For feedback, use the following:
ipd_online_feedback@alcatel-lucent.com
Table of Contents Previous Next Index PDF


Show Commands
System Commands
connections
Syntax 
connections [address ip-address [interface interface-name]] [port port-number] [detail]
Context 
show>system
Description 
This command displays UDP and TCP connection information.
If no command line options are specified, a summary of the TCP and UDP connections displays.
Parameters 
ip-address
Displays only the connection information for the specified IP address.
Values
ipv4-address: a.b.c.d (host bits must be 0)
ipv6-address: x:x:x:x:x:x:x:x[-interface]
x:x:x:x:x:x:d.d.d.d[-interface]
x: [0 — FFFF]H
d: [0 — 255]D
interface: 32 characters maximum, mandatory for link local
addresses
port-number
Displays only the connection information for the specified port number.
Values
detail
Appends TCP statistics to the display output.
Output 
Standard Connection Output
The following table describes the system connections output fields.
Displays the number of output packets sent by the application.
Sample Output
A:ALA-12# show system connections
===============================================================================
Connections :
===============================================================================
Proto    RecvQ    TxmtQ Local Address         Remote Address        State
-------------------------------------------------------------------------------
TCP          0        0 0.0.0.0.21            0.0.0.0.0             LISTEN
TCP          0        0 0.0.0.0.23            0.0.0.0.0             LISTEN
TCP          0        0 0.0.0.0.179           0.0.0.0.0             LISTEN
TCP          0        0 10.0.0.xxx.51138      10.0.0.104.179        SYN_SENT
TCP          0        0 10.0.0.xxx.51139      10.0.0.91.179         SYN_SENT
TCP          0        0 10.10.10.xxx.646      0.0.0.0.0             LISTEN
TCP          0        0 10.10.10.xxx.646      10.10.10.104.49406    ESTABLISHED
TCP          0        0 11.1.0.1.51140        11.1.0.2.179          SYN_SENT
TCP          0        993 192.168.x.xxx.23    192.168.x.xx.xxxx     ESTABLISHED
UDP          0        0 0.0.0.0.123           0.0.0.0.0              ---
UDP          0        0 0.0.0.0.646           0.0.0.0.0              ---
UDP          0        0 0.0.0.0.17185         0.0.0.0.0              ---
UDP          0        0 10.10.10.xxx.646      0.0.0.0.0              ---
UDP          0        0 127.0.0.1.50130       127.0.0.1.17185        ---
-------------------------------------------------------------------------------
No. of Connections: 14
===============================================================================
A:ALA-12# 
 
 
Sample Detailed Output
A:ALA-12# show system connections detail
-------------------------------------------------------------------------------
 TCP Statistics                                                                
-------------------------------------------------------------------------------
packets sent                                : 659635                           
data packets                                : 338982 (7435146 bytes)           
data packet retransmitted                   : 73 (1368 bytes)                  
ack-only packets                            : 320548 (140960 delayed)          
URG only packet                             : 0                                
window probe packet                         : 0                                
window update packet                        : 0                                
control packets                             : 32                               
packets received                            : 658893                           
acks                                        : 338738 for (7435123 bytes)       
duplicate acks                              : 23                               
ack for unsent data                         : 0                                
packets received in-sequence                : 334705 (5568368 bytes)           
completely duplicate packet                 : 2 (36 bytes)                     
packet with some dup. data                  : 0 (0 bytes)                      
out-of-order packets                        : 20 (0 bytes)                     
packet of data after window                 : 0 (0 bytes)                      
window probe                                : 0                                
window update packet                        : 3                                
packets received after close                : 0                                
discarded for bad checksum                  : 0                                
discarded for bad header offset field       : 0                                
discarded because packet too short          : 0                                
connection request                          : 4                                
connection accept                           : 24                               
connections established (including accepts) : 27                               
connections closed                          : 26 (including 2 drops)           
embryonic connections dropped               : 0                                
segments updated rtt                        : 338742 (of 338747 attempts)      
retransmit timeouts                         : 75                               
connections dropped by rexmit timeout       : 0                                
persist timeouts                            : 0                                
keepalive timeouts                          : 26                               
keepalive probes sent                       : 0                                
connections dropped by keepalive            : 1                                
pcb cache lookups failed                    : 0                                
===============================================================================
A:ALA-12#
 
cpu
Syntax 
cpu [sample-period seconds]
Context 
show>system
Description 
This command displays CPU utilization per task over a sample period.
Parameters 
sample-period seconds
The number of seconds over which to sample CPU task utilization.
Default
Values
1 5
Output 
System CPU Output
The following table describes the system CPU output fields.
CPU Utilization
This column does not reflect the true CPU utilization value; that data is still available in the CPU Usage column. This column is the busiest task in each group, where busiest is defined as either actually running or blocked attempting to acquire a lock.
Sample Output
*A:cses-E11# show system cpu sample-period 2
===============================================================================
CPU Utilization (Sample period: 2 seconds)
===============================================================================
Name                                   CPU Time       CPU Usage        Capacity
                                         (uSec)                           Usage
-------------------------------------------------------------------------------
BFD                                          10          ~0.00%          ~0.00%
BGP                                           0           0.00%           0.00%
CFLOWD                                       61          ~0.00%          ~0.00%
Cards & Ports                             8,332           0.41%           0.08%
DHCP Server                                  79          ~0.00%          ~0.00%
ICC                                         408           0.02%           0.01%
IGMP/MLD                                  1,768           0.08%           0.08%
IOM                                      17,197           0.85%           0.31%
IP Stack                                  4,080           0.20%           0.09%
IS-IS                                     1,213           0.06%           0.06%
ISA                                       2,496           0.12%           0.07%
LDP                                           0           0.00%           0.00%
Logging                                      32          ~0.00%          ~0.00%
MPLS/RSVP                                 2,380           0.11%           0.08%
MSDP                                          0           0.00%           0.00%
Management                                5,969           0.29%           0.15%
OAM                                         907           0.04%           0.02%
OSPF                                         25          ~0.00%          ~0.00%
PIM                                       5,600           0.27%           0.27%
RIP                                           0           0.00%           0.00%
RTM/Policies                                  0           0.00%           0.00%
Redundancy                                3,635           0.18%           0.13%
SIM                                       1,462           0.07%           0.04%
SNMP Daemon                                   0           0.00%           0.00%
Services                                  2,241           0.11%           0.05%
Stats                                         0           0.00%           0.00%
Subscriber Mgmt                           2,129           0.10%           0.04%
System                                    8,802           0.43%           0.17%
Traffic Eng                                   0           0.00%           0.00%
VRRP                                        697           0.03%           0.02%
WEB Redirect                                125          ~0.00%          ~0.00%
-------------------------------------------------------------------------------
Total                                 2,014,761         100.00%
   Idle                               1,945,113          96.54%
   Usage                                 69,648           3.45%
Busiest Core Utilization                 69,648           3.45%
===============================================================================
*A:cses-E11#
cron
Syntax 
cron
Context 
show>cron
Description 
This command enters the show CRON context.
action
Syntax 
action [action-name] [owner action-owner] run-history run-state
Context 
show>cron#
Description 
This command displays cron action parameters.
Parameters 
action action-name
Specifies the action name.
Values
owner action-owner
Specifies the owner name.
Default
run-history run-state
Specifies the state of the test to be run.
Values
Output 
The following table describes the show cron action output fields.
 
 
Sample Output
*A:Redundancy# show cron action run-history terminated
===============================================================================
CRON Action Run History
===============================================================================
Action "test"
Owner "TiMOS CLI"
-------------------------------------------------------------------------------
Script Run #17
-------------------------------------------------------------------------------
Start time    : 2006/11/06 20:30:09     End time      : 2006/11/06 20:35:24
Elapsed time  : 0d 00:05:15             Lifetime      : 0d 00:00:00
State         : terminated              Run exit code : noError
Result time   : 2006/11/06 20:35:24     Keep history  : 0d 00:49:57
Error time    : never
Results file  : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203008.
                out
Run exit      : Success
-------------------------------------------------------------------------------
Script Run #18
-------------------------------------------------------------------------------
Start time    : 2006/11/06 20:35:24     End time      : 2006/11/06 20:40:40
Elapsed time  : 0d 00:05:16             Lifetime      : 0d 00:00:00
State         : terminated              Run exit code : noError
Result time   : 2006/11/06 20:40:40     Keep history  : 0d 00:55:13
Error time    : never
Results file  : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203523.
                out
Run exit      : Success
-------------------------------------------------------------------------------
*A:Redundancy#
 
 
*A:Redundancy# show cron action run-history executing
===============================================================================
CRON Action Run History
===============================================================================
Action "test"
Owner "TiMOS CLI"
-------------------------------------------------------------------------------
Script Run #20
-------------------------------------------------------------------------------
Start time    : 2006/11/06 20:46:00     End time      : never
Elapsed time  : 0d 00:00:56             Lifetime      : 0d 00:59:04
State         : executing               Run exit code : noError
Result time   : never                   Keep history  : 0d 01:00:00
Error time    : never
Results file  : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-204559.
                out
=============================================================================== 
*A:Redundancy#
 
 
*A:Redundancy# show cron action run-history initializing
===============================================================================
CRON Action Run History
===============================================================================
Action "test"
Owner "TiMOS CLI"
-------------------------------------------------------------------------------
Script Run #21
-------------------------------------------------------------------------------
Start time    : never                   End time      : never
Elapsed time  : 0d 00:00:00             Lifetime      : 0d 01:00:00
State         : initializing            Run exit code : noError
Result time   : never                   Keep history  : 0d 01:00:00
Error time    : never
Results file  : none
-------------------------------------------------------------------------------
Script Run #22
-------------------------------------------------------------------------------
Start time    : never                   End time      : never
Elapsed time  : 0d 00:00:00             Lifetime      : 0d 01:00:00
State         : initializing            Run exit code : noError
Result time   : never                   Keep history  : 0d 01:00:00
Error time    : never
Results file  : none
-------------------------------------------------------------------------------
Script Run #23
-------------------------------------------------------------------------------
Start time    : never                   End time      : never
Elapsed time  : 0d 00:00:00             Lifetime      : 0d 01:00:00
State         : initializing            Run exit code : noError
Result time   : never                   Keep history  : 0d 01:00:00
Error time    : never
Results file  : none
=============================================================================== 
*A:Redundancy#
schedule
Syntax 
schedule [schedule-name] [owner schedule-owner]
Context 
show>cron#
Description 
This command displays cron schedule parameters.
Parameters 
schedule-name
Displays information for the specified scheduler name.
owner schedule-owner
Displays information for the specified scheduler owner.
Output 
The following table describes the show cron schedule output fields.
 
 
A:sim1>show>cron schedule test
===============================================================================
CRON Schedule Information
===============================================================================
Schedule                     : test
Schedule owner               : TiMOS CLI
Description                  : none
Administrative status        : enabled
Operational status           : enabled
Action                       : test
Action owner                 : TiMOS CLI
Script                       : test
Script Owner                 : TiMOS CLI
Script source location       : ftp://*****:******@192.168.15.1/home/testlab_bgp
                               /cron/test1.cfg
Script results location      : ftp://*****:******@192.168.15.1/home/testlab_bgp
                               /cron/res
Schedule type                : periodic
Interval                     : 0d 00:01:00 (60 seconds)
Next scheduled run           : 0d 00:00:42
Weekday                      : tuesday
Month                        : none
Day of month                 : none
Hour                         : none
Minute                       : none
Number of schedule runs      : 10
Last schedule run            : 2008/01/01 17:20:52
Number of schedule failures  : 0
Last schedule failure        : no error
Last failure time            : never
=============================================================================== 
A:sim1>show>cron
script
Syntax 
script [script-name] [owner script-owner]
Context 
show>cron#
Description 
This command displays cron script parameters.
Parameters 
schedule-name
Displays information for the specified script.
owner schedule-owner
Displays information for the specified script owner.
Output 
The following table describes the show cron script output fields.
Sample Output
A:sim1>show>cron# script
===============================================================================
CRON Script Information
===============================================================================
Script                       : test
Owner name                   : TiMOS CLI
Description                  : asd
Administrative status        : enabled
Operational status           : enabled
Script source location       : ftp://*****:******@192.168.15.1/home/testlab_bgp
                               /cron/test1.cfg
Last script error            : none
Last change                  : 2006/11/07 17:10:03
=============================================================================== 
A:sim1>show>cron#
 
information
Syntax 
information
Context 
show>system
Description 
This command displays general system information including basic system, SNMP server, last boot and DNS client information.
Output 
System Information Output
The following table describes the system information output fields.
Sample Output
A:Dut-F# show system information
===============================================================================
System Information
===============================================================================
System Name            : Dut-F
System Type            : 7750 SR-7 7450 ESS-7
System Version         : B-6.0.B1-6
System Contact         :
System Location        :
System Coordinates     :
System Active Slot     : A
System Up Time         : 0 days, 03:42:01.29 (hr:min:sec)
  
SNMP Port              : 161
SNMP Engine ID         : 0000197f00008c6cff000000
SNMP Max Message Size  : 1500
SNMP Admin State       : Enabled
SNMP Oper State        : Enabled
SNMP Index Boot Status : Not Persistent
SNMP Sync State        : OK
  
Tel/Tel6/SSH/FTP Admin : Enabled/Disabled/Enabled/Enabled
Tel/Tel6/SSH/FTP Oper  : Up/Down/Up/Up
  
BOF Source             : ftp://test:test@xxx.xxx.xx.xxx/./images
Image Source           : primary
Config Source          : primary
Last Booted Config File: ftp://*:*@xxx.xxx.xx.xxx/./images/dut-f.cfg
Last Boot Cfg Version  : N/A
Last Boot Index Version: N/A
Last Saved Config      : N/A
Time Last Saved        : N/A
Changes Since Last Save: No
Max Cfg/BOF Backup Rev : 5
Cfg-OK Script          : ftp://*:*@[3000::8acb:466d]/./images/env.cfg
Cfg-OK Script Status   : failed
Cfg-Fail Script        : N/A
Cfg-Fail Script Status : not used
Management IP Addr     : xxx.xxx.xx.xxx/23
Primary DNS Server     : xxx.xxx.xx.xxx
Secondary DNS Server   : xxx.xxx.xx.xxx
Tertiary DNS Server    : N/A
DNS Domain             : sh.bel.alcatel.be
DNS Resolve Preference : ipv4-only
BOF Static Routes      :
  To                   Next Hop
  138.203.0.0/16       xxx.xxx.xx.xxx
  172.0.0.0/8          xxx.xxx.xx.xxx
ATM Location ID        : 01:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00
ATM OAM Retry Up       : 2
ATM OAM Retry Down     : 4
ATM OAM Loopback Period: 10
===============================================================================
A:Dut-F#
 
lldp
Syntax 
lldp neighbor
Context 
show>system
Description 
This command displays neighbor information for all configured ports without having to specify each individual port ID.
Parameters 
neighbor
Displays LLDP neighbor information.
Sample Output
*A:Dut-C# show system lldp neighbor
Link Layer Discovery Protocol (LLDP) System Information
==============================================================================
NB = nearest-bridge   NTMPR = nearest-non-tpmr   NC = nearest-customer
==============================================================================
Port      Scope  Chassis ID           Index    Port ID     System Name
------------------------------------------------------------------------------
1/1/1     NB     16:2f:ff:00:00:00    1        35717120    Dut-A
2/1/2     NB     16:34:ff:00:00:00    1        35782656    Dut-D
2/1/1     NB     16:36:ff:00:00:00    2        35684352    Dut-E
1/1/2     NB     16:30:ff:00:00:00    2        35749888    Dut-B
1/1/3     NB     16:30:ff:00:00:00    3        35782656    Dut-B
2/1/3     NB     16:30:ff:00:00:00    3        35815424    Dut-B
==============================================================================
Number of neighbors : 6
*A:Dut-C#
 
 
A:GHR-API# show system lldp neighbor
Link Layer Discovery Protocol (LLDP) System Information
==============================================================================
NB = nearest-bridge   NTMPR = nearest-non-tpmr   NC = nearest-customer
==============================================================================
Port      Scope  Chassis ID           Index    Port ID     System Name
------------------------------------------------------------------------------
1/1/6     NTPMR  00:21:05:1b:bc:17    1        36044800    RXI-AMI
1/1/8     NTPMR  00:21:06:6d:bd:53    2        36110336    YOY-WOW
1/1/9     NTPMR  00:21:08:2b:ab:81    3        36143104    FRI-MON
==============================================================================
Number of neighbors : 3
load-balancing-alg
Syntax 
load-balancing-alg [detail]
Context 
show>system
Description 
This command displays system load balancing settings.
Parameters 
detail
Displays port settings.
Sample Output
*A:ALA-49>show>system# load-balancing-alg
===============================================================================
System-wide Load Balancing Algorithms
===============================================================================
L4  - Load Balance                     : exclude-L4
LSR - Load Balance                     : lbl-only
===============================================================================
*A:ALA-49>show>system# 
memory-pools
Syntax 
memory-pools
Context 
show>system
Description 
This command displays system memory status.
Output 
Memory Pools Output
The following table describes memory pool output fields.
Sample Output
A:ALA-1# show system memory-pools
===============================================================================
Memory Pools
===============================================================================
Name               Max Allowed    Current Size      Max So Far          In Use
-------------------------------------------------------------------------------
System                No limit      24,117,248      24,117,248      16,974,832
Icc                  8,388,608       1,048,576       1,048,576          85,200
RTM/Policies          No limit       5,242,912       5,242,912       3,944,104
OSPF                  No limit       3,145,728       3,145,728       2,617,384
MPLS/RSVP             No limit       9,769,480       9,769,480       8,173,760
LDP                   No limit               0               0               0
IS-IS                 No limit               0               0               0
RIP                   No limit               0               0               0
VRRP                  No limit       1,048,576       1,048,576              96
BGP                   No limit       2,097,152       2,097,152       1,624,800
Services              No limit       2,097,152       2,097,152       1,589,824
IOM                   No limit     205,226,800     205,226,800     202,962,744
SIM                   No limit       1,048,576       1,048,576             392
CFLOWD                No limit               0       1,048,576               0
IGMP                  No limit               0               0               0
PIM                   No limit               0               0               0
ATM                   No limit       2,872,648       2,872,648       2,790,104
MMPI                  No limit               0               0               0
MFIB                  No limit               0               0               0
PIP                   No limit      79,943,024      79,943,024      78,895,248
MBUF                67,108,864       5,837,328       5,837,328       4,834,280
-------------------------------------------------------------------------------
Current Total Size :    343,495,200 bytes
Total In Use       :    324,492,768 bytes
Available Memory   :    640,178,652 bytes
===============================================================================
A:ALA-1# 
ntp
Syntax 
ntp
Context 
show>system
Description 
This command displays NTP protocol configuration and state.
Output 
Show NTP Output
The following table describes NTP output fields.
 
 
Sample Output
A:pc-40>config>system>time>ntp# show system ntp
===============================================================================
NTP Status
===============================================================================
Enabled            : Yes                Stratum              : 3
Admin Status       : up                 Oper Status          : up
Server enabled     : No                 Server keyId         : none
System Ref Id      : 192.168.15.221     Auth Check           : Yes
===============================================================================
 
 
A:Dut-A# show system ntp all
===============================================================================
NTP Status
===============================================================================
Configured         : Yes                Stratum              : 1
Admin Status       : up                 Oper Status          : up
Server Enabled     : Yes                Server Authenticate  : No
Clock Source       : PTP
Auth Check         : Yes
Current Date & Time: 2013/03/19 20:18:50 UTC
===============================================================================
===============================================================================
NTP Active Associations
===============================================================================
State                     Reference ID    St Type  A  Poll Reach     Offset(ms)
    Remote
-------------------------------------------------------------------------------
chosen                    PTP            0  srvr  -  256  YYYYYYYY  0.000
    PTP
candidate                 GPS             1  srvr  -  256  YYYYYYYY  -0.054
    138.120.193.198
===============================================================================
A:Dut-A#
 
 
A:pc-40>config>system>time>ntp# show system ntp detail
===============================================================================
NTP Status
===============================================================================
Enabled            : Yes                Stratum              : 3
Admin Status       : up                 Oper Status          : up
Server enabled     : No                 Server keyId         : none
System Ref Id      : 192.168.15.221     Auth Check           : Yes
Auth Errors        : 0                  Auth Errors Ignored  : 0
Auth Key Id Errors : 0                  Auth Key Type Errors : 0
===============================================================================
NTP Configured Broadcast/Multicast Interfaces
===============================================================================
vRouter         Interface           Address             Type    Auth    Poll
-------------------------------------------------------------------------------
Base            i3/1/1              Host-ones           bcast   yes     off
management      management          224.0.1.1           mcast   no      off
Base            t2                                      bclnt   no      n/a
management      management          224.0.1.1           mclnt   no      n/a
===============================================================================
A:pc-40>config>system>time>ntp# 
 
 
A:pc-40>config>system>time>ntp# show system ntp detail all
===============================================================================
NTP Status
===============================================================================
Enabled            : Yes                Stratum              : 3
Admin Status       : up                 Oper Status          : up
Server enabled     : No                 Server keyId         : none
System Ref Id      : 192.168.15.221     Auth Check           : Yes
Auth Errors        : 0                  Auth Errors Ignored  : 0
Auth Key Id Errors : 0                  Auth Key Type Errors : 0
===============================================================================
NTP Configured Broadcast/Multicast Interfaces
===============================================================================
vRouter         Interface           Address             Type    Auth    Poll
-------------------------------------------------------------------------------
Base            i3/1/1              Host-ones           bcast   yes     off
management      management          224.0.1.1           mcast   no      off
Base            t2                                      bclnt   no      n/a
management      management          224.0.1.1           mclnt   no      n/a
===============================================================================
NTP Active Associations
===============================================================================
State      Remote          Reference ID    St  Type   Auth  Poll  R  Offset
-------------------------------------------------------------------------------
reject     192.168.15.221  192.168.14.50   2   srvr   none  64    y  0.901
chosen     192.168.15.221  192.168.1.160   4   mclnt  none  64    y  1.101
===============================================================================
A:pc-40>config>system>time>ntp# 
rollback
Syntax 
rollback
Context 
show>system
Description 
This command displays rollback configuration and state.
Sample Output
A:dut-a_a># show system rollback
===============================================================================
Rollback Information
===============================================================================
Rollback Location               : cf1:/Rollback
Save
  Last Rollback Save Result     : In Progress, Successful or Failed     
  Last Save Completion Time     : 10/15/2010 21:24:06
Revert
  In Progress                   : Yes, No
  Last Revert Initiated Time    : 10/15/2010 21:26:23
  Last Revert Initiated User    : xyz
  Last Initiated Checkpoint     : cf1:/Rollback.rb.3
  Last Completed Revert Result  : Successful or Failed
  Last Revert Completion  Time  : 10/15/2010 21:27:19
================================================================================
Rollback Files
================================================================================
Idx      Suffix   Creation time        Release  User  
           Comment
--------------------------------------------------------------------------------
latest   .rb      2010/10/15 21:24:02  9.0.R4   fred
           This checkpoint was saved after the 3 VPLS services were created
1        .rb.1    2010/10/15 21:23:58  9.0.R4   John
           John’s checkpoint on Sunday
2        .rb.2    2010/10/15 21:23:52  9.0.R4   admin
           A long checkpoint comment that an operator is using to summarize 
           various some of the changes that were made.   They may even have so 
           much to say that they use the maximum comment size.   Notice that 
           words are not chopped.
9        .rb.9    2010/10/14 22:00:01  9.0.R4   admin
           VPLS services 1000-2000 created
53       .rb.53   2010/10/14 22:10:10  9.0.R4   admin 
--------------------------------------------------------------------------------
No. of Rollback Files: 10 
================================================================================
ptp
Syntax 
ptp [peer ip-address [detail] | peers [detail] | unicast | statistics | standby]
Context 
show>system
Description 
This command displays Precision Time Protocol (PTP) configuration and state.
Output 
Show PTP Output
The following table describes PTP output fields.
Sample Output
B:NS082761964# show system ptp 
===============================================================================
IEEE 1588/PTP Clock Information
===============================================================================
-------------------------------------------------------------------------------
Local Clock
-------------------------------------------------------------------------------
Clock Type        : boundary           PTP Profile       : ieee1588-2008
Domain            : 0
Admin State       : up                 Oper State        : up
Rx Announce Rate  : 1 pkt/2 s          Wait To Restore   : disabled
Clock Id          : 001af0fffeb2fead   Clock Class       : 255 (slave-only)
Clock Accuracy    : 0xfe (unknown)     Clock Variance    : ffff (not computed)
Clock Priority1   : 128                Clock Priority2   : 128
PTP Recovery State: locked             Last Changed      : 08/24/2010 13:17:37
Frequency Offset  : +231.920 ppb
-------------------------------------------------------------------------------
Parent Clock
-------------------------------------------------------------------------------
IP Address        : 2.1.1.1
Parent Clock Id   : 001af0fffeab36ad   Remote PTP Port Number: 2
GM Clock Id       : 00b0aefffe011ca6   GM Clock Class    : 13
GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance : 0x6400 (3.7E-09)
GM Clock Priority1: 128                GM Clock Priority2: 128
-------------------------------------------------------------------------------
Time Information
-------------------------------------------------------------------------------
Timescale           : PTP
Current Time        : 2013/02/11 23:05:26.6 (UTC)
Frequency Traceable : yes
Time Traceable      : yes
Time Source         : GPS
==============================================================================
 
 
B:NS082761964# show system ptp standby
===============================================================================
IEEE 1588/PTP Clock Information
===============================================================================
-------------------------------------------------------------------------------
Local Clock
-------------------------------------------------------------------------------
Clock Type        : ordinary,slave     PTP Profile       : ieee1588-2008
Domain            : 0
Admin State       : up                 Oper State        : up
Clock Id          : 001af0fffeb2fead   Clock Class       : 255 (slave-only)
Clock Accuracy    : 0xfe (unknown)     Clock Variance    : ffff (not computed)
Clock Priority1   : 128                Clock Priority2   : 128
PTP Port State    : listening          Last Changed       : 02/11/2013 18:09:58
PTP Recovery State: locked             Last Changed      : 08/24/2010 13:17:37
Frequency Offset  : +231.920 ppb
-------------------------------------------------------------------------------
Parent Clock
-------------------------------------------------------------------------------
IP Address        : 2.1.1.1
Parent Clock Id   : 001af0fffeab36ad   Remote PTP Port Number: 2
GM Clock Id       : 00b0aefffe011ca6   GM Clock Class    : 13
GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance : 0x6400 (3.7E-09)
GM Clock Priority1: 128                GM Clock Priority2: 128
-------------------------------------------------------------------------------
Time Information
-------------------------------------------------------------------------------
Timescale           : PTP
Current Time        : 2011-08-30 15:31:42.99 UTC
Frequency Traceable : yes
Time Traceable      : yes
Time Source         : gps
==============================================================================
 
 
A:bksim1619# show system ptp statistics 
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
                                                      Input              Output
-------------------------------------------------------------------------------
PTP Packets                                         2910253            2393354
  Announce                                             9015              22682
  Sync                                              1153275             622585
  Follow Up                                               0                  0
  Delay Request                                      594036            1153568
  Delay Response                                    1153044             593614
  Signaling                                             883                905
    Request TLVs                                        428                598
      Announce                                          304                350
      Sync                                               62                124
      Delay Response                                     62                124
    Grant TLVs (Granted)                                514                428
      Announce                                          272                304
      Sync                                              121                 62
      Delay Response                                    121                 62
    Grant TLVs (Rejected)                                 0                  0
      Announce                                            0                  0
      Sync                                                0                  0
      Delay Response                                      0                  0
    Cancel TLVs                                           3                  0
      Announce                                            1                  0
      Sync                                                1                  0
      Delay Response                                      1                  0
    Ack Cancel TLVs                                       0                  3
      Announce                                            0                  1
      Sync                                                0                  1
      Delay Response                                      0                  1
    Other TLVs                                            0                  0
  Other                                                   0                  0
  Event Packets timestamped at port                  215523             215371
  Event Packets timestamped in software                   0                  0
  Discards                                                0                  0
    Bad domain value                                      0                  0
    Alternate Master Flag Set                             0                  0
    Other                                                 0                  0
==============================================================================
===============================================================================
IEEE 1588/PTP Clock Recovery State Statistics
===============================================================================
State                                                                 Seconds  
-------------------------------------------------------------------------------
Initial                                                                   136
Acquiring                                                                   0
Phase-Tracking                                                              0
Locked                                                                      0
Hold-over                                                                   0
===============================================================================
===============================================================================
IEEE 1588/PTP Clock Recovery Event Statistics
===============================================================================
Event                                                                   Count 
-------------------------------------------------------------------------------
Packet Loss                                                                 0
Excessive Packet Loss                                                       0
Excessive Phase Shift Detected                                              0
Too Much Packet Delay Variation                                             0
===============================================================================
 
*B:Dut-B# show system ptp  statistics
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
                                                               Input     Output
-------------------------------------------------------------------------------
PTP Packets                                                   934483     934473
  Announce                                                      2489       2507
  Sync                                                        310598     310597
  Follow Up                                                        0          0
  Delay Request                                               310596     310598
  Delay Response                                              310598     310596
  Signaling                                                      202        175
    Request Unicast Transmission TLVs                            102        103
      Announce                                                    34         37
      Sync                                                        34         33
      Delay Response                                              34         33
    Grant Unicast Transmission (Accepted) TLVs                   100        102
      Announce                                                    34         34
      Sync                                                        33         34
      Delay Response                                              33         34
    Grant Unicast Transmission (Denied) TLVs                       0          0
      Announce                                                     0          0
      Sync                                                         0          0
      Delay Response                                               0          0
    Cancel Unicast Transmission TLVs                               0          3
      Announce                                                     0          1
      Sync                                                         0          1
      Delay Response                                               0          1
    Ack Cancel Unicast Transmission TLVs                           0          0
      Announce                                                     0          0
      Sync                                                         0          0
      Delay Response                                               0          0
    Other TLVs                                                     0          0
  Other                                                            0          0
  Event Packets timestamped at port                           621194     621195
  Event Packets timestamped at cpm                                 0          0
Discards                                                           0          0
  Bad PTP domain                                                   0          0
  Alternate Master                                                 0          0
  Other                                                            0          0
===============================================================================
IEEE 1588/PTP Clock Recovery State Statistics
===============================================================================
State                                                                   Seconds
-------------------------------------------------------------------------------
Initial                                                                     441
Acquiring                                                                   261
Phase-Tracking                                                                8
Locked                                                                     4268
Hold-over                                                                     0
===============================================================================
IEEE 1588/PTP Clock Recovery Event Statistics
===============================================================================
Event                                                      Sync Flow Delay Flow
-------------------------------------------------------------------------------
Packet Loss                                                        0          0
Excessive Packet Loss                                              0          0
Excessive Phase Shift Detected                                     0          0
Too Much Packet Delay Variation                                    0          0
===============================================================================
*B:Dut-B#
 
A:bksim1620# show system ptp peers detail 
===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
IP Address        : 3.1.1.1            Announce Direction : tx
Admin State       : n/a                G.8265.1 Priority  : n/a
Local PTP Port    : 3                  PTP Port State     : master
Clock Id          : ac65fffffe000000   Remote PTP Port    : 1
Tx Timestamp Point: port               Rx Timestamp Point : port
Last Tx Port      : 1/1/1              Last Rx Port       : 1/1/1
-------------------------------------------------------------------------------
IP Address        : 5.1.1.2            Announce Direction : rx
Admin State       : up                 G.8265.1 Priority  : n/a
Local PTP Port    : 1                  PTP Port State     : slave
Clock Id          : ac5cfffffe000000   Remote PTP Port    : 1
GM Clock Id       : ac5cfffffe000000   GM Clock Class     : 13
GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance  : ffff (not computed)
GM Clock Priority1: 128                GM Clock Priority2 : 128
Steps Removed     : 0                  Parent Clock:      : yes
Tx Timestamp Point: cpm                Rx Timestamp Point : cpm
Last Tx Port      : 1/2/1              Last Rx Port       : 1/2/1
-------------------------------------------------------------------------------
IP Address        : 6.1.1.2            Announce Direction : rx+tx
Admin State       : up                 G.8265.1 Priority  : n/a
Local PTP Port    : 2                  PTP Port State     : passive
Clock Id          : ac5dfffffe000000   Remote PTP Port    : 2
GM Clock Id       : ac5cfffffe000000   GM Clock Class     : 13
GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance  : ffff (not computed)
GM Clock Priority1: 128                GM Clock Priority2 : 128
Steps Removed     : 1                  Parent Clock       : no
Tx Timestamp Point: port               Rx Timestamp Point : port
Last Tx Port      : 3/2/1              Last Rx Port       : 3/2/1
-------------------------------------------------------------------------------
IP Address        : 11.1.1.2           Announce Direction : tx/rx
Admin State       : up                 G.8265.1 Priority  : n/a
Local PTP Port    : 3                  PTP Port State     : master
Clock Id          : ac5dfffffe000000   Remote PTP Port    : 2
Alarms            : 
Tx Timestamp Point: cpm                Rx Timestamp Point : cpm
Last Tx Port      : 7/2/5              Last Rx Port       : 6/2/3
===============================================================================
 
 
A:bksim1620# show system ptp peer 6.1.1.2 
===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
IP Address        : 6.1.1.2            Announce Direction : rx+tx
Admin State       : up                 G.8265.1 Priority  : n/a
Local PTP Port    : 2                  PTP Port State     : passive
Clock Id          : ac5dfffffe000000   Remote PTP Port    : 2
GM Clock Id       : ac5cfffffe000000   GM Clock Class     : 13
GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance  : ffff (not computed)
GM Clock Priority1: 128                GM Clock Priority2 : 128
Steps Removed     : 1                  Parent Clock       : no
Tx Timestamp Point: port               Rx Timestamp Point : port
Last Tx Port      : 3/2/1              Last Rx Port       : 3/2/1
===============================================================================
 
sntp
Syntax 
sntp
Context 
show>system
Description 
This command displays SNTP protocol configuration and state.
Output 
Show SNTP Output
The following table describes SNTP output fields.
Sample Output
A:ALA-1# show system sntp
===============================================================================
SNTP                                                                           
===============================================================================
SNTP Server            Version            Preference         Interval          
-------------------------------------------------------------------------------
10.10.20.253           3                  Preferred          64                
===============================================================================
A:ALA-1#
thresholds
Syntax 
thresholds
Context 
show>system
Description 
This command display system monitoring thresholds. The “Threshold Events Log” table will keep only the last 201 entries.
Output 
Thresholds Output
following table describes system threshold output fields.
Displays the numerical identifier for the alarm.
Displays the polling interval, in seconds, over which the data is sampled and compared with the rising and falling thresholds.
Displays the method of sampling the selected variable and calculating the value to be compared against the thresholds.
Displays the alarm that may be sent when this alarm is first created.
Sample Output
A:ALA-48# show system thresholds
================================================================
Threshold Alarms
================================================================
Variable: tmnxCpmFlashUsed.1.11.1
Alarm Id         : 1        Last Value : 835
Rising Event Id  : 1        Threshold  : 5000
Falling Event Id : 2        Threshold  : 2500
Sample Interval  : 2147483* SampleType : absolute
Startup Alarm    : either   Owner      : TiMOS CLI
Variable: tmnxCpmFlashUsed.1.11.1
Alarm Id         : 2        Last Value : 835
Rising Event Id  : 3        Threshold  : 10000
Falling Event Id : 4        Threshold  : 5000
Sample Interval  : 2147483* SampleType : absolute
Startup Alarm    : rising   Owner      : TiMOS CLI
Variable: sgiMemoryUsed.0
Alarm Id         : 3        Last Value : 42841056
Rising Event Id  : 5        Threshold  : 4000
Falling Event Id : 6        Threshold  : 2000
Sample Interval  : 2147836  SampleType : absolute
Startup Alarm    : either   Owner      : TiMOS CLI
================================================================
* indicates that the corresponding row element may have been truncated.
================================================================
Threshold Events
================================================================
Description: TiMOS CLI - cflash capacity alarm rising event
Event Id         : 1        Last Sent  : 10/31/2006 08:47:59
Action Type      : both     Owner      : TiMOS CLI
Description: TiMOS CLI - cflash capacity alarm falling event
Event Id         : 2        Last Sent  : 10/31/2006 08:48:00
Action Type      : both     Owner      : TiMOS CLI
Description: TiMOS CLI - cflash capacity warning rising event
Event Id         : 3        Last Sent  : 10/31/2006 08:47:59
Action Type      : both     Owner      : TiMOS CLI
Description: TiMOS CLI - cflash capacity warning falling event
Event Id         : 4        Last Sent  : 10/31/2006 08:47:59
Action Type      : both     Owner      : TiMOS CLI
Description: TiMOS CLI - memory usage alarm rising event
Event Id         : 5        Last Sent  : 10/31/2006 08:48:00
Action Type      : both     Owner      : TiMOS CLI
Description: TiMOS CLI - memory usage alarm falling event
Event Id         : 6        Last Sent  : 10/31/2006 08:47:59
Action Type      : both     Owner      : TiMOS CLI
================================================================
Threshold Events Log
================================================================
Description      : TiMOS CLI - cflash capacity alarm falling eve
                   nt : value=835, <=2500 : alarm-index 1, event
                   -index 2 alarm-variable OID tmnxCpmFlashUsed.
                   1.11.1
Event Id         : 2        Time Sent  : 10/31/2006 08:48:00
Description      : TiMOS CLI - memory usage alarm rising event :
                    value=42841056, >=4000 : alarm-index 3, even
                   t-index 5 alarm-variable OID sgiMemoryUsed.0
Event Id         : 5        Time Sent  : 10/31/2006 08:48:00
================================================================
A:ALA-48#
 
time
Syntax 
time
Context 
show>system
Description 
This command displays the system time and zone configuration parameters.
Output 
System Time Output
The following table describes system time output fields.
 
Sample Output
A:ALA-1# show system time
===============================================================================
Date & Time
===============================================================================
Current Date & Time : 2006/05/05 23:03:13    DST Active            : yes
Current Zone        : PDT                    Offset from UTC       : -7:00
-------------------------------------------------------------------------------
Non-DST Zone        : PST                    Offset from UTC       : -8:00
Zone type           : standard
-------------------------------------------------------------------------------
DST Zone            : PDT                    Offset from Non-DST   : 0:60
Starts              : first sunday in april 02:00
Ends                : last sunday in october 02:00
============================================================================
A:ALA-1#
 
 
A:ALA-1# show system time (with no DST zone configured)
===============================================================================
Date & Time
===============================================================================
Current Date & Time : 2006/05/12 11:12:05	       DST Active      :     no
Current Zone	    : APA			       Offset from UTC :  -8:00
-------------------------------------------------------------------------------
Non-DST Zone	    : APA			       Offset from UTC :  -8:00
Zone Type           : non-standard
-------------------------------------------------------------------------------
No DST zone configured
===============================================================================
A:ALA-1#
time
Syntax 
time
Context 
show
Description 
This command displays the current day, date, time and time zone.
The time is displayed either in the local time zone or in UTC depending on the setting of the root level time-display command for the console session.
Output 
Sample Output
A:ALA-49# show time
Tue Oct 31 12:17:15 GMT 2006
tod-suite
Syntax 
tod-suite [detail]
tod-suite associations
tod-suite failed-associations
Context 
show>cron
Description 
This command displays information on the configured time-of-day suite.
Output 
CRON TOD Suite Output
The following table describes TOD suite output fields:
Sample Output
A:kerckhot_4# show cron tod-suite suite_sixteen detail
===============================================================================
Cron tod-suite details
===============================================================================
Name        : suite_sixteen
Type / Id                        Time-range                       Prio  State
-------------------------------------------------------------------------------
Ingress Qos Policy
  1160                           day                              5     Inact
  1190                           night                            6     Activ
Ingress Scheduler Policy
  SchedPolCust1_Day              day                              5     Inact
  SchedPolCust1_Night            night                            6     Activ
Egress Qos Policy
  1160                           day                              5     Inact
  1190                           night                            6     Activ
Egress Scheduler Policy
  SchedPolCust1Egress_Day        day                              5     Inact
===============================================================================
A:kerckhot_4#
 
The following example shows output for TOD suite associations.
A:kerckhot_4# show cron tod-suite suite_sixteen associations 
=============================================================================== 
Cron tod-suite associations for suite suite_sixteen 
=============================================================================== 
Service associations 
------------------------------------------------------------------------------- 
Service Id  : 1                         Type   : VPLS 
 SAP 1/1/1:1 
 SAP 1/1/1:2 
 SAP 1/1/1:3 
 SAP 1/1/1:4 
 SAP 1/1/1:5 
 SAP 1/1/1:6 
 SAP 1/1/1:20 
------------------------------------------------------------------------------- 
Number of SAP's : 7 
Customer Multi-Service Site associations 
------------------------------------------------------------------------------- 
Multi Service Site: mss_1_1 
------------------------------------------------------------------------------- 
Number of MSS's: 1 
===============================================================================
A:kerckhot_4#
 
The following example shows output for TOD suite failed-associations.
A:kerckhot_4# show cron tod-suite suite_sixteen failed-associations
===============================================================================
Cron tod-suite associations failed
===============================================================================
tod-suite suite_sixteen : failed association for SAP
-------------------------------------------------------------------------------
Service Id  : 1                         Type   : VPLS
  SAP 1/1/1:2
  SAP 1/1/1:3
  SAP 1/1/1:4
  SAP 1/1/1:5
  SAP 1/1/1:6
  SAP 1/1/1:20
-------------------------------------------------------------------------------
tod-suite suite_sixteen : failed association for Customer MSS
-------------------------------------------------------------------------------
None
-------------------------------------------------------------------------------
Number of tod-suites failed/total : 1/1
===============================================================================
A:kerckhot_4#
 
Zooming in on one of the failed SAPs, the assignments of QoS and scheduler policies are shown as not as intended:
A:kerckhot_4# show service id 1 sap 1/1/1:2
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id         : 1
SAP                : 1/1/1:2                  Encap             : q-tag
Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100
Admin State        : Up                       Oper State        : Up
Flags              : None
Last Status Change : 10/05/2006 18:11:34
Last Mgmt Change   : 10/05/2006 22:27:48
Max Nbr of MAC Addr: No Limit                 Total MAC Addr    : 0
Learned MAC Addr   : 0                        Static MAC Addr   : 0
Admin MTU          : 1518                     Oper MTU          : 1518
Ingress qos-policy : 1130                     Egress qos-policy : 1130
Intend Ing qos-pol*: 1190                     Intend Egr qos-po*: 1190
Shared Q plcy      : n/a                      Multipoint shared : Disabled
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
Ingr IPv6 Fltr-Id  : n/a                      Egr IPv6 Fltr-Id  : n/a
tod-suite          : suite_sixteen            qinq-pbit-marking : both
Egr Agg Rate Limit : max
ARP Reply Agent    : Unknown                  Host Conn Verify  : Disabled
Mac Learning       : Enabled                  Discard Unkwn Srce: Disabled
Mac Aging          : Enabled                  Mac Pinning       : Disabled
L2PT Termination   : Disabled                 BPDU Translation  : Disabled
 
Multi Svc Site     : None
I. Sched Pol       : SchedPolCust1
Intend I Sched Pol : SchedPolCust1_Night
E. Sched Pol       : SchedPolCust1Egress
Intend E Sched Pol : SchedPolCust1Egress_Night
Acct. Pol          : None                     Collect Stats     : Disabled
Anti Spoofing      : None                     Nbr Static Hosts  : 0
===============================================================================
A:kerckhot_4#
 
If a time-range is specified for a filter entry, use the show filter command to view results:
A:kerckhot_4# show filter ip  10
===============================================================================
IP Filter
===============================================================================
Filter Id    : 10                               Applied        : No
Scope        : Template                         Def. Action    : Drop
Entries      : 2
-------------------------------------------------------------------------------
Filter Match Criteria : IP
-------------------------------------------------------------------------------
Entry        : 1010
time-range   : day                              Cur. Status    : Inactive
Log Id       : n/a
Src. IP      : 0.0.0.0/0                        Src. Port      : None
Dest. IP     : 10.10.100.1/24                   Dest. Port     : None
Protocol     : Undefined                        Dscp           : Undefined
ICMP Type    : Undefined                        ICMP Code      : Undefined
Fragment     : Off                              Option-present : Off
Sampling     : Off                              Int. Sampling  : On
IP-Option    : 0/0                              Multiple Option: Off
TCP-syn      : Off                              TCP-ack        : Off
Match action : Forward
Next Hop     : 138.203.228.28
Ing. Matches : 0                                Egr. Matches   : 0
Entry        : 1020
time-range   : night                            Cur. Status    : Active
Log Id       : n/a
Src. IP      : 0.0.0.0/0                        Src. Port      : None
Dest. IP     : 10.10.1.1/16                     Dest. Port     : None
Protocol     : Undefined                        Dscp           : Undefined
ICMP Type    : Undefined                        ICMP Code      : Undefined
Fragment     : Off                              Option-present : Off
Sampling     : Off                              Int. Sampling  : On
IP-Option    : 0/0                              Multiple Option: Off
TCP-syn      : Off                              TCP-ack        : Off
Match action : Forward
Next Hop     : 172.22.184.101
Ing. Matches : 0                                Egr. Matches   : 0
=============================================================================== 
A:kerckhot_4#
If a filter is referred to in a TOD Suite assignment, use the show filter associations command to view the output:
A:kerckhot_4# show filter ip 160 associations
===============================================================================
IP Filter
===============================================================================
Filter Id    : 160                              Applied        : No
Scope        : Template                         Def. Action    : Drop
Entries      : 0
-------------------------------------------------------------------------------
Filter Association : IP
-------------------------------------------------------------------------------
Tod-suite "english_suite"
- ingress, time-range "day" (priority 5)
=============================================================================== 
A:kerckhot_4#
redundancy
Syntax 
redundancy
Context 
show
Description 
This command enables the context to show redundancy information.
multi-chassis
Syntax 
multi-chassis
Context 
show>redundancy
Description 
This command enables the context to show multi-chassis redundancy information.
all
Syntax 
all [detail]
Context 
show>redundancy>multi-chassis
Description 
This command displays brief multi-chassis redundancy information.
Parameters 
detail
Shows detailed multi-chassis redundancy information.
Output 
Show Redundancy Multi-Chassis All Output
The following table describes Redundancy Multi-Chassis All fields:
 
Sample Output
B:Dut-B# show redundancy multi-chassis all
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address         : 10.10.10.2
Description             : Mc-Lag peer 10.10.10.2
Authentication          : Disabled
Source IP Address       : 0.0.0.0
Admin State             : Enabled
===============================================================================
B:Dut-B#
 
 
B:Dut-B# show lag detail
===============================================================================
LAG Details
===============================================================================
LAG 1
-------------------------------------------------------------------------------
Description: Description For LAG Number 1
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Lag-id              : 1                     Mode                 : access
Adm                 : up                    Opr                  : up
Thres. Exceeded Cnt : 9                     Port Threshold       : 0
Thres. Last Cleared : 05/20/2006 00:12:35   Threshold Action     : down
Dynamic Cost        : false                 Encap Type           : null
Configured Address  : 1c:71:ff:00:01:41     Lag-IfIndex          : 1342177281
Hardware Address    : 1c:71:ff:00:01:41     Adapt Qos            : distribute
Hold-time Down      : 0.0 sec
LACP                : enabled               Mode                 : active
LACP Transmit Intvl : fast                  LACP xmit stdby      : enabled
Selection Criteria  : highest-count         Slave-to-partner     : disabled
Number of sub-groups: 1                     Forced               : -
System Id           : 1c:71:ff:00:00:00     System Priority      : 32768
Admin Key           : 32768                 Oper Key             : 32666
Prtr System Id      : 20:f4:ff:00:00:00     Prtr System Priority : 32768
Prtr Oper Key       : 32768
 
MC Peer Address     : 10.10.10.2            MC Peer Lag-id       : 1
MC System Id        : 00:00:00:33:33:33     MC System Priority   : 32888
MC Admin Key        : 32666                 MC Active/Standby    : active
MC Lacp ID in use   : true                  MC extended timeout  : false
MC Selection Logic  : peer decided
MC Config Mismatch  : no mismatch
-------------------------------------------------------------------------------
Port-id        Adm    Act/Stdby Opr    Primary   Sub-group     Forced   Prio
-------------------------------------------------------------------------------
331/2/1          up     active    up     yes       1             -        32768
331/2/2          up     active    up               1             -        32768
331/2/3          up     active    up               1             -        32768
331/2/4          up     active    up               1             -        32768
-------------------------------------------------------------------------------
Port-id        Role      Exp   Def   Dist  Col   Syn   Aggr  Timeout  Activity
-------------------------------------------------------------------------------
331/2/1          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/1          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/2          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/2          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/3          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/3          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/4          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes
331/2/4          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes
===============================================================================
B:Dut-B#
mc-endpoint
Syntax 
mc-endpoint statistics
mc-endpoint peer [ip-address] statistics
mc-endpoint endpoint [mcep-id] statistics
mc-endpoint peer [ip-address]
Context 
show>redundancy>multi-chassis
Description 
This command displays multi-chassis endpoint information.
Parameters 
statistics
Displays the global statistics for the MC endpoint.
peer ip-address
Specifies the IP address of multi-chassis end-point peer.
endpoint mcep-id
Specifies the nulti-chassis endpoint.
Values
Sample Output
*A:Dut-B# show redundancy multi-chassis mc-endpoint statistics 
===============================================================================
Multi-Chassis Endpoint Global Statistics
===============================================================================
Packets Rx                                  : 533                              
Packets Rx Keepalive                        : 522                              
Packets Rx Config                           : 3                                
Packets Rx Peer Config                      : 1                                
Packets Rx State                            : 7                                
Packets Dropped Keep-Alive Task             : 7                                
Packets Dropped Too Short                   : 0                                
Packets Dropped Verify Failed               : 0                                
Packets Dropped Tlv Invalid Size            : 0                                
Packets Dropped Out Of Seq                  : 0                                
Packets Dropped Unknown Tlv                 : 0                                
Packets Dropped Tlv Invalid MC-Endpoint Id  : 0                                
Packets Dropped MD5                         : 0                                
Packets Dropped Unknown Peer                : 0                                
Packets Dropped MC Endpoint No Peer         : 0                                
Packets Tx                                  : 26099                            
Packets Tx Keepalive                        : 8221                             
Packets Tx Config                           : 2                                
Packets Tx Peer Config                      : 17872                            
Packets Tx State                            : 4                                
Packets Tx Failed                           : 0                                
===============================================================================
*A:Dut-B# 
 
*A:Dut-B# show redundancy multi-chassis mc-endpoint peer 3.1.1.3 statistics 
===============================================================================
Multi-Chassis MC-Endpoint Statistics
===============================================================================
Peer Addr                         : 3.1.1.3                                    
-------------------------------------------------------------------------------
Packets Rx                        : 597                                        
Packets Rx Keepalive              : 586                                        
Packets Rx Config                 : 3                                          
Packets Rx Peer Config            : 1                                          
Packets Rx State                  : 7                                          
Packets Dropped State Disabled    : 0                                          
Packets Dropped Packets Too Short : 0                                          
Packets Dropped Tlv Invalid Size  : 0                                          
Packets Dropped Tlv Invalid LagId : 0                                          
Packets Dropped Out of Seq        : 0                                          
Packets Dropped Unknown Tlv       : 0                                          
Packets Dropped MD5               : 0                                          
Packets Tx                        : 636                                        
Packets Tx Keepalive              : 600                                        
Packets Tx Peer Config            : 30                                         
Packets Tx Failed                 : 0                                          
Packets Dropped No Peer           : 0                                          
===============================================================================
*A:Dut-B# 
 
*A:Dut-B# show redundancy multi-chassis mc-endpoint  endpoint 1 statistics 
===============================================================================
Multi-Chassis Endpoint Statistics
===============================================================================
===============================================================================
MC-Endpoint Id 1
===============================================================================
Packets Rx Config                 : 3                                          
Packets Rx State                  : 7                                          
Packets Tx Config                 : 2                                          
Packets Tx State                  : 4                                          
Packets Tx Failed                 : 0                                          
===============================================================================
Number of Entries 1
===============================================================================
mc-lag
Syntax 
mc-lag [lag lag-id]
Context 
show>redundancy>multi-chassis
Description 
This command displays multi-chassis LAG information.
Parameters 
lag lag-id
Shows information for the specified LAG identifier.
Values
mc-mobile
Syntax 
mc-mobile peer {ip-address | ip6-address}
Context 
show>redundancy>multi-chassis
Description 
This command displays multi-chassis LAG information.
Parameters 
ip-address
Shows information for the specified IPv4 peer.
ipv6-address
Shows information for the specified IPv6 peer.
Sample Output
*A:Dut-A# show redundancy multi-chassis mc-mobile peer 10.90.1.2 
===============================================================================
Multi-chassis Peer Mc-Mobile Table
===============================================================================
Peer                 : 10.90.1.2        
Last State Change    : 12/04/2012 23:23:43
Admin State          : Up/Down               Oper State      : Up/Down/ISSU
Peer Version         : 5.0Rx                             
Keep Alive           : 10 deci-sec      Hold On Nbr Fail     : 3
BFD Svc ID           : 0                BFD Interface Name   : mc_intloopback
-------------------------------------------------------------------------------
Gateway Id           : 2                
-------------------------------------------------------------------------------
Admin Role           : Primary          Oper Role            : Master
Peer Admin Role      : Secondary        Peer Oper Role       : Slave
Admin State          : Up               Oper State           : Up
Last Time Peer Connected : 12/04/2012 23:23:43
 
Last State Change    : 12/04/2012 23:23:43
Last State Chg Reason: Traffic Evnt     
Geo-Redundancy State : Hot             
 
CPM                  : 0                Geo Redundancy       : Hot
MSCP Group           : 1                Geo Redundancy       : Hot
===============================================================================
*A:Dut-A# 
peer
Syntax 
peer ip-address [lag lag-id]
Context 
show>redundancy>multi-chassis>mc-lag
Description 
This command enables the context to display mc-lag peer-related redundancy information.
Parameters 
ip-address
Shows peer information about the specified IP address.
lag lag-id
Shows information for the specified LAG identifier.
Values
Output 
Show Redundancy Multi-chassis MC-Lag Peer Output
The following table describes show redundancy multi-chassis mc-lag peer output fields:
 
Sample Output
A:subscr_mgt# show redundancy multi-chassis mc-lag peer 10.10.10.30 
===============================================================================
Multi-Chassis MC-Lag Peer 10.10.10.30
===============================================================================
Last Changed    : 01/23/2007 18:20:13                                          
Admin State     : Up                  Oper State           : Up                
KeepAlive       : 10 deci-seconds     Hold On Ngbr Failure : 3                 
-------------------------------------------------------------------------------
Lag Id Lacp Key Remote Lag Id System Id          Sys Prio Last Changed       
-------------------------------------------------------------------------------
1      1        1             00:00:00:00:00:01  1        01/23/2007 18:20:13
2      2        2             00:00:00:00:00:02  2        01/24/2007 08:53:48
-------------------------------------------------------------------------------
Number of LAGs : 2
===============================================================================
A:subscr_mgt#
 
 
 
A:subscr_mgt# show redundancy multi-chassis mc-lag peer 10.10.10.30 lag 1 
===============================================================================
Multi-Chassis MC-Lag Peer 10.10.10.30
===============================================================================
Last Changed    : 01/23/2007 18:20:13                                          
Admin State     : Up                  Oper State           : Up                
KeepAlive       : 10 deci-seconds     Hold On Ngbr Failure : 3                 
-------------------------------------------------------------------------------
Lag Id Lacp Key Remote Lag Id System Id          Sys Prio Last Changed       
-------------------------------------------------------------------------------
1      1        1             00:00:00:00:00:01  1        01/23/2007 18:20:13
-------------------------------------------------------------------------------
Number of LAGs : 1
===============================================================================
A:subscr_mgt#
statistics
Syntax 
statistics mc-lag [peer ip-address [lag lag-id]]
Context 
show>redundancy>multi-chassis>mc-lag
Description 
This command displays multi-chassis statistics.
Parameters 
mc-lag
Displays multi-chassis LAG statistics.
peer ip-address
Shows the specified address of the multi-chassis peer.
lag lag-id
Shows information for the specified LAG identifier.
Values
Output 
Show Redundancy Multi-chassis MC-Lag Peer Statistics Output
The following table describes show redundancy multi-chassis mc-lag peer output fields:
 
Sample Output
A:subscr_mgt# show redundancy multi-chassis mc-lag statistics 
===============================================================================
Multi-Chassis Statistics
===============================================================================
Packets Rx                        : 52535                                      
Packets Rx Keepalive              : 52518                                      
Packets Rx Config                 : 2                                          
Packets Rx Peer Config            : 4                                          
Packets Rx State                  : 6                                          
Packets Dropped KeepaliveTask     : 0                                          
Packets Dropped Packet Too Short  : 0                                          
Packets Dropped Verify Failed     : 0                                          
Packets Dropped Tlv Invalid Size  : 0                                          
Packets Dropped Out of Seq        : 0                                          
Packets Dropped Unknown Tlv       : 0                                          
Packets Dropped Tlv Invalid LagId : 0                                          
Packets Dropped MD5               : 0                                          
Packets Dropped Unknown Peer      : 0                                          
Packets Tx                        : 52583                                      
Packets Tx Keepalive              : 52519                                      
Packets Tx Config                 : 2                                          
Packets Tx Peer Config            : 54                                         
Packets Tx State                  : 8                                          
Packets Tx Failed                 : 0                                          
===============================================================================
A:subscr_mgt#
 
B:Dut-B# show redundancy multi-chassis mc-lag peer 10.10.10.2 statistics
===============================================================================
Multi-Chassis Statistics, Peer 10.10.10.2
===============================================================================
Packets Rx                        : 231
Packets Rx Keepalive              : 216
Packets Rx Config                 : 1
Packets Rx Peer Config            : 2
Packets Rx State                  : 12
Packets Dropped State Disabled    : 0
Packets Dropped Packets Too Short : 0
Packets Dropped Tlv Invalid Size  : 0
Packets Dropped Tlv Invalid LagId : 0
Packets Dropped Out of Seq        : 0
Packets Dropped Unknown Tlv       : 0
Packets Dropped MD5               : 0
Packets Tx                        : 235
Packets Tx Keepalive              : 216
Packets Tx Peer Config            : 3
Packets Tx Failed                 : 0
===============================================================================
B:Dut-B#
mc-ring
Syntax 
mc-ring peer ip-address statistics
mc-ring peer ip-address [ring sync-tag [detail|statistics] ]
mc-ring peer ip-address ring sync-tag ring-node [ring-node-name [detail|statistics] ]
mc-ring global-statistics
Context 
show>redundancy>multi-chassis
Description 
This command displays multi-chassis ring information.
Parameters 
ip-address
Specifies the address of the multi-chassis peer to display.
ring sync-tag
Specifies a synchronization tag to be displayed that was used while synchronizing this port with the multi-chassis peer.
node ring-node-name
Specifies a ring-node name.
global-statistics
Displays global statistics for the multi-chassis ring.
detail
Displays detailed peer information for the multi-chassis ring.
Output 
Show mc-ring peer ip-address ring Output
The following table describes mc-ring peer ip-address ring output fields.
 
Sample Output
*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2 ring ring11 detail
==============================================================================
Multi-Chassis MC-Ring Detailed Information
==============================================================================
Peer           : 10.0.0.2
Sync Tag       : ring11
Port ID        : 1/1/3
Admin State    : inService
Oper State     : connected
Admin Change   : 01/07/2008 21:40:07
Oper Change    : 01/07/2008 21:40:24
Failure Reason : None
------------------------------------------------------------------------------
In Band Control Path
------------------------------------------------------------------------------
Service ID     : 10
Interface Name : to_an1
Oper State     : connected
Dest IP        : 10.10.0.2
Src  IP        : 10.10.0.1
------------------------------------------------------------------------------
VLAN Map B Path Provisioned
------------------------------------------------------------------------------
range 13-13
range 17-17
------------------------------------------------------------------------------
VLAN Map Excluded Path Provisioned
------------------------------------------------------------------------------
range 18-18
------------------------------------------------------------------------------
VLAN Map B Path Operational
------------------------------------------------------------------------------
range 13-13
range 17-17
------------------------------------------------------------------------------
VLAN Map Excluded Path Operational
------------------------------------------------------------------------------
range 18-18
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
 
*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 192.251.10.104
==============================================================================
MC Ring entries
==============================================================================
Sync Tag                         Oper State      Failure Reason
------------------------------------------------------------------------------
No. of MC Ring entries: 0
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
 
*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2
==============================================================================
MC Ring entries
==============================================================================
Sync Tag                         Oper State      Failure Reason
------------------------------------------------------------------------------
ring11                           connected       None
ring12                           shutdown        None
------------------------------------------------------------------------------
No. of MC Ring entries: 4
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
 
*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2 ring ring11 ring-node an1 detail
==============================================================================
Multi-Chassis MC-Ring Node Detailed Information
==============================================================================
Peer           : 10.0.0.2
Sync Tag       : ring11
Node Name      : an1
Oper State Loc : connected
Oper State Rem : notTested
In Use         : True
Admin Change   : 01/07/2008 21:40:07
Oper Change    : 01/07/2008 21:40:25
Failure Reason : None
------------------------------------------------------------------------------
Ring Node Connectivity Verification
------------------------------------------------------------------------------
Admin State    : inService
Service ID     : 11
VLAN Tag       : 11
Dest IP        : 10.11.3.1
Src  IP        : None
Interval       : 1 minutes
Src MAC        : None
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
 
*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2 ring ring11 ring-node
==============================================================================
MC Ring Node entries
==============================================================================
Name                             Loc Oper St.      Failure Reason
  In Use                           Rem Oper St.
------------------------------------------------------------------------------
an1                              connected         None
  Yes                              notTested
an2                              connected         None
  Yes                              notTested
------------------------------------------------------------------------------
No. of MC Ring Node entries: 2
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
 
Show Redundancy Multi-Chassis Ring Peer Statistics Output
The following table describes multi-chassis ring peer output fields.
 
 
Sample Output
*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 192.251.10.104 statistics
==============================================================================
MC Ring statistics for peer 192.251.10.104
==============================================================================
Message                                              Received     Transmitted
------------------------------------------------------------------------------
MCS ID Request                                       0            0
MCS ID Response                                      0            0
Ring Exists Request                                  0            0
Ring Exists Response                                 0            0
Keepalive                                            0            0
------------------------------------------------------------------------------
Total                                                0            0
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
Show mc-ring ring-node Command Output
Show mc-ring global-statistics Command Output
 
*A:ALA-48>show>redundancy>multi-chassis# mc-ring global-statistics
==============================================================================
Global MC Ring statistics
==============================================================================
Rx                           : 0
Rx Too Short                 : 0
Rx Wrong Authentication      : 0
Rx Invalid TLV               : 0
Rx Incomplete                : 0
Rx Unknown Type              : 0
Rx Unknown Peer              : 0
Rx Unknown Ring              : 0
Rx Unknown Ring Node         : 0
Tx                           : 36763
Tx No Buffer                 : 0
Tx Transmission Failed       : 0
Tx Unknown Destination       : 0
Missed Configuration Events  : 0
Missed BFD Events            : 0
==============================================================================
*A:ALA-48>show>redundancy>multi-chassis#
 
sync
Syntax 
sync [port port-id | lag-id]
Context 
show>redundancy>multi-chassis
Description 
This command displays synchronization information.
Parameters 
port port-id
Shows the specified port ID of the multi-chassis peer.
lag lag-id
Shows information for the specified LAG identifier.
Values
Output 
Show Redundancy Multi-chassis Sync Output
The following table describes show redundancy multi-chassis sync output fields:
 
Sample Output
*A:subscr_mgt_2# show redundancy multi-chassis sync 
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address         : 10.10.10.20                                          
Description             : Mc-Lag peer 10.10.10.20
Authentication          : Disabled                                             
Source IP Address       : 0.0.0.0                                              
Admin State             : Enabled                                              
-------------------------------------------------------------------------------
Sync-status
-------------------------------------------------------------------------------
Client Applications     : SUBMGMT                                              
Sync Admin State        : Up                                                   
Sync Oper State         : Up                                                   
DB Sync State           : inSync                                               
Num Entries             : 1                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
Rem Num Entries         : 1                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
===============================================================================
A:subscr_mgt_2# 
peer
Syntax 
peer ip-address
Context 
show>redundancy>multi-chassis>sync
Description 
This command enables the context to display peer-related redundancy information.
Parameters 
ip-address
Shows peer information about the specified IP address.
Output 
Show Redundancy Multi-chassis Sync Peer Output
The following table describes show redundancy multi-chassis sync output fields:
 
Sample Output
*A:subscr_mgt_2# show redundancy multi-chassis sync peer 10.10.10.20 
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address         : 10.10.10.20                                          
Description             : Mc-Lag peer 10.10.10.20
Authentication          : Disabled                                             
Source IP Address       : 0.0.0.0                                              
Admin State             : Enabled                                              
-------------------------------------------------------------------------------
Sync-status
-------------------------------------------------------------------------------
Client Applications     : SUBMGMT                                              
Sync Admin State        : Up                                                   
Sync Oper State         : Up                                                   
DB Sync State           : inSync                                               
Num Entries             : 1                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
Rem Num Entries         : 1                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0 
===============================================================================
MCS Application Stats
===============================================================================
Application             : igmp                                                 
Num Entries             : 0                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 0                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
-------------------------------------------------------------------------------
Application             : igmpSnooping                                         
Num Entries             : 0                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 0                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
-------------------------------------------------------------------------------
Application             : subMgmt                                              
Num Entries             : 1                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 1                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
-------------------------------------------------------------------------------
Application             : srrp                                                 
Num Entries             : 0                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 0                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
===============================================================================
*A:subscr_mgt_2# 
detail
Syntax 
detail
Context 
show>redundancy>multi-chassis>peer
Description 
This command displays detailed peer information.
Output 
Show Redundancy Multi-chassis Sync Peer Detail Output
The following table describes show redundancy multi-chassis sync detail output fields:
 
Sample Output
*A:subscr_mgt_2# show redundancy multi-chassis sync peer 10.10.10.20 detail 
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address         : 10.10.10.20                                          
Description             : Mc-Lag peer 10.10.10.20
Authentication          : Disabled                                             
Source IP Address       : 0.0.0.0                                              
Admin State             : Enabled                                              
-------------------------------------------------------------------------------
Sync-status
-------------------------------------------------------------------------------
Client Applications     : SUBMGMT                                              
Sync Admin State        : Up                                                   
Sync Oper State         : Up                                                   
DB Sync State           : inSync                                               
Num Entries             : 1                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
Rem Num Entries         : 1                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0 
===============================================================================
MCS Application Stats
===============================================================================
Application             : igmp                                                 
Num Entries             : 0                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 0                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
-------------------------------------------------------------------------------
Application             : igmpSnooping                                         
Num Entries             : 0                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 0                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
-------------------------------------------------------------------------------
Application             : subMgmt                                              
Num Entries             : 1                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 1                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
-------------------------------------------------------------------------------
Application             : srrp                                                 
Num Entries             : 0                                                    
Lcl Deleted Entries     : 0                                                    
Alarm Entries           : 0                                                    
-------------------------------------------------------------------------------
Rem Num Entries         : 0                                                    
Rem Lcl Deleted Entries : 0                                                    
Rem Alarm Entries       : 0                                                    
===============================================================================
Ports synced on peer 10.10.10.20
===============================================================================
Port/Encap                    Tag                                              
-------------------------------------------------------------------------------
lag-1                         test123                                          
===============================================================================
*A:subscr_mgt_2#
 
synchronization
Syntax 
synchronization
Context 
show>redundancy
Description 
This command displays redundancy synchronization times.
Sample Output
A:ALA-48>show>redundancy# synchronization
===============================================================================
Synchronization Information
===============================================================================
Standby Status               : disabled
Last Standby Failure         : N/A
Standby Up Time              : N/A
Failover Time                : N/A
Failover Reason              : N/A
Boot/Config Sync Mode        : None
Boot/Config Sync Status      : No synchronization
Last Config File Sync Time   : Never
Last Boot Env Sync Time      : Never
===============================================================================
A:ALA-48>show>redundancy#
time-range
Syntax 
time-range name associations [detail]
Context 
show>cron
Description 
This command displays information on the configured time ranges.
Output 
Time Range Output
The following table displays system time range output fields:
Sample Output
The following example shows time-range detail output.
A:ala# show cron time-range time-range2 detail
===============================================================================
Cron time-range
===============================================================================
Name 	    : time-range1
Periodic	    : Start * * * * End * * * *
Absolute 	    : Start * * * * End * * * *
 
The following example shows output for time-range associations with previously created IP and MAC filters.
A:ala# show cron time-range day associations
===============================================================================
Cron time-range associations
===============================================================================
Name          : day                            State  : Inactive
-------------------------------------------------------------------------------
IP Filter associations
-------------------------------------------------------------------------------
IP filter Id  : 10, entry 1010
-------------------------------------------------------------------------------
MAC Filter associations
-------------------------------------------------------------------------------
None
-------------------------------------------------------------------------------
Tod-suite associations
-------------------------------------------------------------------------------
Tod-suite : suite_sixteen, for Ingress Qos Policy "1160"
Tod-suite : suite_sixteen, for Ingress Scheduler Policy "SchedPolCust1_Day"
Tod-suite : suite_sixteen, for Egress Qos Policy "1160"
Tod-suite : suite_sixteen, for Egress Scheduler Policy "SchedPolCust1Egress_Day
===============================================================================
uptime
Syntax 
uptime
Context 
show
Description 
This command displays the time since the system started.
Output 
Uptime Output
The following table describes uptime output fields.
Sample Output
A:ALA-1# show uptime
System Up Time         : 11 days, 18:32:02.22 (hr:min:sec)
 
A:ALA-1#
switch-fabric
Syntax 
switch-fabric
Context 
show>system
Description 
This command displays switch fabric information.
Output 
Switch fabric output
The following table describes switch-fabric output fields for 12-slot and 7-slot chassis models:.
Displays the fabric slot within a chassis in the system. The CPM cards and IOM cards cannot be physically inserted into the switch fabric card slots.
Sample Output
A:ALA-7# show system switch-fabric 
==============================================================================
Switch Fabric
==============================================================================
Slot/Mda Min. Forwarding Capacity Max. Forwarding Capacity
------------------------------------------------------------------------------
1/1 100% 100%
1/2 100% 100%
2/1 100% 100%
2/2 100% 100%
3/1 100% 100%
3/2 100% 100%
4/1 100% 100%
4/2 100% 100%
5/1 100% 100%
5/2 100% 100%
A 100% 100%
B 100% 100%
==============================================================================
A:ALA-7#
 
A:ALA-12# show system switch-fabric 
==============================================================================
Switch Fabric
==============================================================================
Slot/Mda Min. Forwarding Capacity Max. Forwarding Capacity
------------------------------------------------------------------------------
1/1 100% 100%
1/2 100% 100%
2/1 100% 100%
2/2 100% 100%
3/1 100% 100%
3/2 100% 100%
4/1 100% 100%
4/2 100% 100%
5/1 100% 100%
5/2 100% 100%
6/1 100% 100%
6/2 100% 100%
7/1 100% 100%
7/2 100% 100%
8/1 100% 100%
8/2 100% 100%
A 100% 100%
B 100% 100%
==============================================================================
A:ALA-12
sync-if-timing
Syntax 
sync-if-timing
Context 
show>system
Description 
This command displays synchronous interface timing operational information.
Output 
System Timing Output
The following table describes sync-if-timing output fields.
BITS A, BITS B - (7750 SR-7/12)
Mate CPM (BITS A), Mate CPM (BITS B) - (7750 SR-7/12 on the active CPM)
Mate CPM (none) - show>system>sync-if-timing> standby when standby locked to active which is freerun or holdover - (7750 SR-7/12)
Mate CPM (ref1), Mate CPM (ref2) - show>system>sync-if-timing>standby when standby locked to active which is locked to ref1 or ref2 - (7750 SR-7/12)
The ref1 or ref2 configuration is administratively shutdown.
The ref1 or ref2 configuration is administratively enabled.
The following example is for a node locked to the active BITS input and directing the signal on ref1 to the BITS output:
Sample Output
*A:SR7# show system sync-if-timing 
===============================================================================
System Interface Timing Operational Info
===============================================================================
System Status CPM A                : Master Locked
    Reference Input Mode           : Non-revertive
    Quality Level Selection        : Disabled
    Reference Selected             : BITS A
    System Quality Level           : prs
    Current Frequency Offset (ppm) : +0
 
Reference Order                    : bits ref1 ref2
 
Reference Mate CPM   
    Qualified For Use              : Yes
    Selected For Use               : No
        Not Selected Due To        :     on standby
 
Reference Input 1   
    Admin Status                   : up
    Rx Quality Level               : prs
    Qualified Level Override       : none
    Qualified For Use              : Yes
    Selected For Use               : No
        Not Selected Due To        :     on standby
    Source Port                    : 3/1/2
 
Reference Input 2      
    Admin Status                   : down
    Rx Quality Level               : unknown
    Qualified Level Override       : none
    Qualified For Use              : No
        Not Qualified Due To       :     disabled
    Selected For Use               : No
        Not Selected Due To        :     disabled
    Source Port                    : None
 
Reference BITS A   
    Admin Status                   : up
    Rx Quality Level               : prs
    Qualified Level Override       : none
    Qualified For Use              : Yes
    Selected For Use               : Yes
    Interface Type                 : DS1
    Framing                        : ESF
    Line Coding                    : B8ZS
    Line Length                    : 550-660ft
    Output Admin Status          : up
    Output Admin State           : ref1
    Output Source                : prs
    Output Reference Selected    : ptp
    Tx Quality Level             : prs
 
===============================================================================
*A:SR7# 
 
 
The following example is for a node locked to the standby CPM BITS input and directing the ref1 signal to the BITS output port:
*A:Dut-B# show system sync-if-timing
=======================================================================
System Interface Timing Operational Info 
=======================================================================
System Status CPM A                : Master Locked
    Reference Input Mode           : Non-revertive
    Quality Level Selection        : Disabled
    Reference Selected             : Mate CPM (BITS B)
    System Quality Level           : prs
    Current Frequency Offset (ppm) : +0
 
Reference Order                    : bits ref1 ref2
 
Reference Mate CPM   
    Qualified For Use              : Yes
    Selected For Use               : Yes
 
Reference Input 1   
    Admin Status                   : up
    Rx Quality Level               : prs
    Quality Level Override         : none
    Qualified For Use              : Yes
    Selected For Use               : No
        Not Selected Due To        : on standby
    Source Port                    : 3/1/2
 
Reference Input 2      
    Admin Status                   : down
    Rx Quality Level               : unknown
    Quality Level Override         : none
    Qualified For Use              : No
        Not Qualified Due To       : disabled
    Selected For Use               : No
        Not Selected Due To        : disabled
    Source Port                    : None
 
Reference BITS A 
    Admin Status                   : up
    Rx Quality Level               : unknown
    Quality Level Override         : none
    Qualified For Use              : No
        Not Qualified Due To       : LOS 
    Selected For Use               : No
        Not Selected Due To        : not qualified
    Interface Type                 : DS1
    Framing                        : ESF
    Line Coding                    : B8ZS
    Line Length                    : 550-660ft
    Output Admin Status            : up
    Output Admin State             : ref1
    Output Source                  : prs
    Output Reference Selected      : ptp
    Tx Quality Level               : prs
======================================================================
 
The following example is for a node whose standby CPM is locked to its local BITS port and the signal from ref1 is directed to the BITS output port:
A:SR7# show system sync-if-timing standby 
===============================================================================
System Interface Timing Operational Info
===============================================================================
System Status CPM B                : Master Locked
    Reference Input Mode           : Non-revertive
    Quality Level Selection        : Disabled
    Reference Selected             : BITS B
    System Quality Level           : prs
    Current Frequency Offset (ppm) : +0
 
Reference Order                    : bits ref1 ref2
 
Reference Mate CPM   
    Qualified For Use              : Yes
    Selected For Use               : No
        Not Selected Due To        : on standby
 
Reference Input 1   
    Admin Status                   : down
    Rx Quality Level               : unknown
    Quality Level Override         : none
    Qualified For Use              : No
        Not Qualified Due To       : disabled
    Selected For Use               : No
        Not Selected Due To        : disabled
    Source Port                    : None
 
Reference Input 2      
    Rx Quality Level               : unknown
    Quality Level Override         : none
    Qualified For Use              : No
        Not Qualified Due To       : disabled
    Selected For Use               : No
        Not Selected Due To        : disabled
    Source Port                    : None
 
Reference BITS B
    Admin Status                   : up
    Rx Quality Level               : prs
    Quality Level Override         : none
    Qualified For Use              : Yes
    Selected For Use               : Yes
    Interface Type                 : DS1
    Framing                        : ESF
    Line Coding                    : B8ZS
    Line Length                    : 550-660ft
    Output Admin Status            : up
    Output Admin State             : ref1
    Output Source                  : prs
    Output Reference Selected      : ptp
    Tx Quality Level               : prs
===============================================================================
*A:SR7# 
 
synchronization
Syntax 
synchronization
Context 
show>redundancy>synchronization
Description 
This command displays redundancy synchronization times.
Output 
Synchronization Output
The following table describes redundancy synchronization output fields.
Displays the timestamp when the last redundancy failover occurred causing a switchover from active to standby CPM. If there is no redundant CPM card in this system or no failover has occurred since the system last booted, the value will be 0.
Displays the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the configuration files or the boot environment information contained in the boot options file (BOF).
Sample Output
A:ALA-1>show>redundancy# synchronization
===============================================================================
Synchronization Information
===============================================================================
Standby Status               : disabled
Last Standby Failure         : N/A
Standby Up Time              : N/A
Failover Time                : N/A
Failover Reason              : N/A
Boot/Config Sync Mode        : None
Boot/Config Sync Status      : No synchronization
Last Config File Sync Time   : Never
Last Boot Env Sync Time      : Never
===============================================================================
A:ALA-1>show>redundancy#
 
 
Debug Commands
sync-if-timing
Syntax 
sync-if-timing
Context 
debug
Description 
The context to debug synchronous interface timing references.
force-reference
Syntax 
force-reference {ref1 | ref2 | bits | ptp}
no force-reference
Context 
debug>sync-if-timing
Description 
This command allows an operator to force the system synchronous timing output to use a specific reference.
Note: The debug sync-if-timing force-reference command should only be used to test and debug problems. Network synchronization problems may appear if network elements are left with this manual override setting. Once the system timing reference input has been forced, it may be cleared using the no force-reference command.
The CPM clock can be forced to use a specific input reference using the force-reference command.
When the command is executed, the CPM clock on the active CPM immediately switches its input reference to that specified by the command. If the specified input is not available (shutdown), or in a disqualified state, the CPM clock shall use the next qualified input reference based on the selection rules.
This command also affects the BITS output port on the active CPM. If the BITS output port selection is set to line-reference and the reference being forced is not the BITS input port, then the system uses the forced reference to generate the signal out the BITS output port. If the BITS output port selection is set to internal-clock, then the system uses the output of the CPM clock to generate the signal for the BITS output port.
On a CPM activity switch, the force command is cleared and normal reference selection is determined.
Debug configurations are not saved between reboots.
Note: The 7750 SR-c4 has two BITS input ports on the CFM. The force reference command on this system allows the selection of the specific port.
7750 SR-c4 CLI Syntax: debug>sync-if-timing>force-reference {ref1 | ref2 | bits1 | bits2}
Parameters 
ref1
The clock will use the first timing reference.
ref2
The clock will use the second timing reference.
bits
The clock will use the external network interface on the active CPM to be the highest priority input.
bits1
(7750 SR-c4) The clock will use the bits1 timing reference.
bits2
(7750 SR-c4) The clock will use the bits2 timing reference.
ptp
The clock will use the PTP slave as the timing reference.
system
Syntax 
[no] system
Context 
debug
Description 
This command displays system debug information.
 
http-connections
Syntax 
http-connections [host-ip-address/mask]
http-connections
Context 
debug>system
Description 
This command displays HTTP connections debug information.
Parameters 
host-ip-address/mask
Displays information for the specified host IP address and mask.
ntp
Syntax 
[no] router router-name interface ip-int-name
Context 
debug>system
Description 
This command enables and configures debugging for NTP.
The no form of the command disables debugging for NTP.
Parameters 
router-name
Base, management
Default
ip-int-name
maximum 32 characters; must begin with a letter. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
persistence
Syntax 
[no] persistence
Context 
debug>system
Description 
This command displays persistence debug information.
Tools Commands
redundancy
Syntax 
redundancy
Context 
tools>dump
Description 
This command enables the context to dump redundancy parameters.
multi-chassis
Syntax 
multi-chassis
Context 
tools>dump>redundancy
Description 
This command enables the context to dump multi-chassis parameters.
mc-endpoint
Syntax 
mc-endpoint peer ip-address
Context 
tools>dump>redundancy>multi-chassis
Description 
This command dumps multi-chassis endpoint information.
Parameters 
peer ip-address
Specifies the peer’s IP address.
Sample Output
*A:Dut-B# tools dump redundancy multi-chassis mc-endpoint peer 3.1.1.3 
MC Endpoint Peer Info
    peer addr                    : 3.1.1.3
    peer name                    : Dut-C
    peer name refs               : 1
    src addr conf                : Yes
    source addr                  : 2.1.1.2
    num of mcep                  : 1
    num of non-mcep              : 0
    own sess num                 : 58ba0d39
    mc admin state               : Up
    tlv own mc admin state       : Up
    tlv peer mc admin state      : Up
    reachable                    : Yes
 
    own sys priority             : 50
    own sys id                   : 00:03:fa:72:c3:c0
    peer sys priority            : 21
    peer sys id                  : 00:03:fa:c6:31:f8
    master                       : No
 
    conf boot timer              : 300
    boot timer active            : No 
    conf ka intv                 : 10
    conf hold on num of fail     : 3
    tlv own ka intv              : 10
    tlv peer ka intv             : 10
    ka timeout tmr active        : Yes
    ka timeout tmr intvl         : 20
    ka timeout tmr time left     : 4
    peer ka intv                 : 10
    mc peer timed out            : No
 
    initial peer conf rx         : Yes
    peer-mc disabled             : No
    initial peer conf sync       : Yes
    peer conf sync               : Yes
 
    own passive mode             : Disable
    peer passive mode            : No
 
    retransmit pending           : No
    non-mcep retransmit pending  : No
    retransmit intvl             : 5
    last tx time                 : 1437130
    last rx time                 : 1437156
 
    own bfd                      : Enable
    peer bfd                     : Enable
    bfd vrtr if                  : 2
    bfd handle                   : 1
    bfd state                    : 3
    bfd code                     : 0
 
*A:Dut-B#
mc-ring
Syntax 
mc-ring
mc-ring peer ip-address [ring sync-tag]
Context 
tools>dump>redundancy>multi-chassis
Description 
This command dumps multi-chassis ring information.
peer ip-address
Specifies the peer’s IP address.
ring sync-tag
Specifies the ring’s sync-tag created in the config>redundancy>mc>peer>mcr> ring context.
 
sync-database
Syntax 
sync-database [peer ip-address] [port port-id | lag-id] [sync-tag sync-tag] [application application] [detail] [type type]
Context 
tools>dump>redundancy>multi-chassis
Description 
This command dumps MCS database information.
peer ip-address
Specifies the peer’s IP address.
port port-id | lag-id
Indicates the port or LAG ID to be synchronized with the multi-chassis peer.
slot/mda/port or lag-lag-id
sync-tag sync-tag
Specifies a synchronization tag to be used while synchronizing this port with the multi-chassis peer.
application application
Specifies a particular multi-chassis peer synchronization protocol application.
Values
dhcp-server: local dhcp server
igmp: Internet group management protocol
igmp-snooping: igmp-snooping
mc-ring : multi-chassis ring
mld-snooping: multicast listener discovery-snooping
srrp: simple router redundancy protocol
sub-host-trk: subscriber host tracking
sub-mgmt: subscriber management
type type
Indicates the locally deleted or alarmed deleted entries in the MCS database per multi-chassis peer.
Values
detail
Displays detailed information.
srrp-sync-data
Syntax 
srrp-sync-database [instance instance-id] [peer ip-address]
Context 
tools>dump>redundancy>multi-chassis
Description 
This command dumps SRRP database information.
peer ip-address
Specifies the peer’s IP address.
instance instance-id
Dumps information for the specified Subscriber Router Redundancy Protocol instance configured on this system.
Values
 
Clear Commands
application-assurance
Syntax 
application-assurance
Context 
clear
Description 
This command clears application assurance commands.
group
Syntax 
group isa-aa-group-id statistics
group isa-aa-group-id status
Context 
clear>app-assure
Description 
This command clears application assurance group data.
Parameters 
isa-aa-group-id
Specifies the ISA-AA group index.
Values
status
Specifies that application assurance system statistics are cleared.
statistics
Specifies that application assurance statistics are cleared.
cron
Syntax 
cron action completed [action-name] [owner action-owner]
Context 
clear
Description 
This command clears completed CRON action run history entries.
Parameters 
action-name
Specifies the action name.
Values
owner action-owner
Specifies the owner name.
Default
 
redundancy
Syntax 
redundancy
Context 
clear
Description 
This command enables the context to clear redundancy parameters.
multi-chassis
Syntax 
multi-chassis
Context 
clear>redundancy
Description 
This command enables the context to clear multi-chassis parameters.
mc-mobile
Syntax 
mc-mobile statistics peer {ip-address | ipv6-address}
Context 
clear>redundancy
Description 
This command enables the context to clear multi-chassis parameters.
mc-endpoint
Syntax 
mc-endpoint endpoint [mcep-id] statistics
mc-endpoint statistics
mc-endpoint peer [ip-address] statistics
Context 
clear>redundancy>multi-chassis
Description 
This command clears multi-chassis endpoint statistics.
endpoint mcep-id
Clears information for the specified multi-chassis endpoint ID.
Values
peer ip-address
Clears information for the specified peer IP address.
statistics
Clears statistics for this multi-chassis endpoint.
mc-lag
Syntax 
mc-lag [peer ip-address [lag lag-id]]
Context 
clear>redundancy>multi-chassis
Description 
This command clears multi-chassis Link Aggregation Group (LAG) information.
Parameters 
peer ip-address
Clears the specified address of the multi-chassis peer.
lag lag-id
Clears the specified LAG on this system.
Values
mc-ring
Syntax 
mc-ring
Context 
clear>redundancy>multi-chassis
Description 
This command clears multi-chassis ring data.
debounce
Syntax 
debounce peer ip-address ring sync-tag
Context 
clear>redundancy>multi-chassis
Description 
This command clears multi-chassis ring operational state debounce history.
Parameters 
ip-address
Clears debounce historyf or the specified IP address.
ring sync-tag
Clears debounce history for the specified sync tag.
ring-nodes
Syntax 
ring-nodes peer ip-address ring sync-tag
Context 
clear>redundancy>multi-chassis>mcr
Description 
This command clears multi-chassis ring unreferenced ring nodes.
Parameters 
ip-address
Clears ring statistics for the specified IP address.
ring sync-tag
Clears ring statistics for the specified sync tag.
statistics
Syntax 
statistics
Context 
clear>redundancy>multi-chassis>mcr
Description 
This command clears multi-chassis ring
global
Syntax 
global
Context 
clear>redundancy>multi-chassis>mcr>statistics
Description 
This command clears multi-chassis ring global statistics.
peer
Syntax 
peer ip-address
Context 
clear>redundancy>multi-chassis>mcr>statistics
Description 
This command clears multi-chassis ring peer statistics.
Parameters 
ip-address
Clears ring peer statistics for the specified IP address.
ring
Syntax 
ring peer ip-address ring sync-tag
Context 
clear>redundancy>multi-chassis>mcr>statistics
Description 
This command clears multi-chassis ring statistics.
Parameters 
ip-address
Clears ring statistics for the specified IP address.
ring sync-tag
Clears ring statistics for the specified sync tag.
ring-node
Syntax 
ring-node peer ip-address ring sync-tag node ring-node-name
Context 
clear>redundancy>multi-chassis>mcr>statistics
Description 
This command clears multi-chassis ring statistics.
Parameters 
peer ip-address
Clears ring-node peer statistics for the specified IP address.
ring sync-tag
Clears ring-node peer statistics for the specified sync-tag.
node ring-node-name
Clears ring-node peer statistics for the specified ring node name.
ptp
Syntax 
ptp inactive-peers
ptp statistics
ptp peer ip_address statistics
Context 
clear>system
Description 
This command clears PTP statistics.
Parameters 
inactive-peers
Removes PTP peers which are not currently exchanging PTP packets with the router.
peer ip-address statistics
Clears statistics for the specified peer.
statistics
Clears all ptp statistics.
sync-database
Syntax 
sync-database peer ip-address all application application
sync-database peer ip-address { port port-id | lag-id | sync-tag sync-tag } application application
sync-database peer ip-address port port-id | lag-id sync-tag sync-tag application application
Context 
clear>redundancy>multi-chassis
Description 
This command clears multi-chassis sync database information.
Parameters 
peer ip-address
Clears the specified address of the multi-chassis peer.
port port-id
Clears the specified port ID of the multi-chassis peer.
port lag-id
Clears the specified Link Aggregation Group (LAG) on this system.
all
Clears all ports and/or sync tags.
sync-tag sync-tag
Clears the synchronization tag used while synchronizing this port with the multi-chassis peer.
application
Clears the specified application information that was synchronized with the multi-chassis peer.
Values
all: All supported applications
dhcp-server: local dhcp server
igmp: internet group management protocol
igmp-snooping: igmp-snooping
mc-ring: multi-chassis ring
mld-snooping: multicast listener discovery-snooping
srrp: simple router redundancy protocol
sub-host-trk subscriber host tracking
sub-mgmt: subscriber management
screen
Syntax 
screen
Context 
clear
Description 
This command allows an operator to clear the Telnet or console screen.
system
Syntax 
system sync-if-timing {ref1 | ref2 | bits}
Context 
clear
Description 
This command allows an operator to individually clear (re-enable) a previously failed reference. As long as the reference is one of the valid options, this command is always executed. An inherent behavior enables the revertive mode which causes a re-evaluation of all available references.
sync-if-timing
Syntax 
system sync-if-timing {ref1 | ref2}
Context 
clear
Description 
This command allows an operator to individually clear (re-enable) a previously failed reference. As long as the reference is one of the valid options, this command is always executed. An inherent behavior enables the revertive mode which causes a re-evaluation of all available references.
Parameters 
ref1
clears the first timing reference
ref2
clears the second timing reference
trace
Syntax 
trace log
Context 
clear
Description 
This command allows an operator to clear the trace log.