Show Commands

Syntax

This command displays the memory pools for the card.

Context

show>system>card

Description

connections

Syntax

connections [address ip-address] [port port-number] [detail]

Context

This command displays UDP and TCP connection information.
If no command line options are specified, a summary of the TCP and UDP connections displays.

Description

Parameters

Displays only the connection information for the specified IP address.

Values

ipv4-address: a.b.c.d (host bits must be 0)
ipv6-address: x:x:x:x:x:x:x:x[-interface]
x:x:x:x:x:x:d.d.d.d[-interface]
x: [0 — FFFF]H
d: [0 — 255]D
interface: 32 characters maximum, mandatory for link local
addresses

port-number

Displays only the connection information for the specified port number.

Values

0 — 65535

Appends TCP statistics to the display output.

Output

Standard Connection Output

The following table describes the system connections output fields.

Label

Description

Proto

Displays the socket protocol, either TCP or UDP.

RecvQ

Displays the number of input packets received by the protocol.

TxmtQ

Displays the number of output packets sent by the application.

Local Address

Displays the local address of the socket. The socket port is separated by a period.

Remote Address

Displays the remote address of the socket. The socket port is separated by a period.

State

Listen

The protocol state is in the listen mode.

Established

The protocol state is established.

vRtrID

The virtual router identifier.

•

vRtrID 0 — listens for connections in all routing instances including the Base and Management VRFs.

•

vRtrID 1 — Base routing instance

•

vRtrID 4095 — Management routing instance

MSS

The TCP maximum segment size.

A:ALA-12# show system connections

===============================================================================

Connections

===============================================================================

Prot RecvQ   TxmtQ   Local Address                                   State

                MSS  Remote Address                                      vRtrID

-------------------------------------------------------------------------------

TCP        0       0 0.0.0.0.21                                      LISTEN

               1024  0.0.0.0.0                                                0

TCP        0       0 0.0.0.0.22                                      LISTEN

               1024  0.0.0.0.0                                                0

TCP        0       0 0.0.0.0.23                                      LISTEN

               1024  0.0.0.0.0                                                0

TCP        0       0 0.0.0.0.830                                     LISTEN

               1024  0.0.0.0.0                                                0

TCP        0       0 0.0.0.0.6068                                    LISTEN

               1024  0.0.0.0.0                                                0

TCP        0       0 0.0.0.0.47806                                   LISTEN

               1024  0.0.0.0.0                                                0

TCP        0       0 ::.21                                           LISTEN

               1024  ::.0                                                     0

TCP        0       0 ::.22                                           LISTEN

               1024  ::.0                                                     0

TCP        0       0 ::.830                                          LISTEN

               1024  ::.0                                                     0

TCP        0       0 ::.47806                                        LISTEN

               1024  ::.0                                                     0

TCP        0       0 127.1.0.11.21                                   LISTEN

               1024  0.0.0.0.0                                             4095

TCP        0       0 127.1.0.11.21059                                LISTEN

               1024  0.0.0.0.0                                             4095

TCP        0       0 135.121.129.98.22                               LISTEN

               1024  0.0.0.0.0                                             4095

TCP        0       0 135.121.129.98.23                               ESTABLISH

               1024  138.120.140.149.59042                                 4095

TCP        0    1149 135.121.129.98.23                               ESTABLISH

               1024  138.120.140.244.58579                                 4095

TCP        0       0 135.121.129.98.830                              LISTEN

               1024  0.0.0.0.0                                             4095

TCP        0       0 3000::8779:8163.22                              LISTEN

               1024  ::.0                                                  4095

TCP        0       0 3000::8779:8163.830                             LISTEN

               1024  ::.0                                                  4095

UDP        0       0 0.0.0.0.67                                       ---

                     0.0.0.0.0                                                0

UDP        0       0 0.0.0.0.68                                       ---

                     0.0.0.0.0                                                0

UDP        0       0 0.0.0.0.123                                      ---

                     0.0.0.0.0                                                0

UDP        0       0 0.0.0.0.319                                      ---

                     0.0.0.0.0                                                0

UDP        0       0 0.0.0.0.320                                      ---

                     0.0.0.0.0                                                0

UDP        0       0 0.0.0.0.514                                      ---

                     0.0.0.0.0                                                0

UDP        0       0 0.0.0.0.50055                                    ---

                     0.0.0.0.0                                                0

UDP        0       0 ::.123                                           ---

                     ::.0                                                     0

UDP        0       0 ::.50056                                         ---

                     ::.0                                                     0

UDP        0       0 0.0.0.0.1025                                     ---

                     0.0.0.0.0                                                1

UDP        0       0 0.0.0.0.123                                      ---

                     0.0.0.0.0                                             4095

UDP        0       0 0.0.0.0.49152

-------------------------------------------------------------------------------

No. of Connections: 18

===============================================================================

A:ALA-12#

Sample Detailed Output

A:ALA-12# show system connections detail

-------------------------------------------------------------------------------

 TCP Statistics

-------------------------------------------------------------------------------

packets sent                                : 659635

data packets                                : 338982 (7435146 bytes)

data packet retransmitted                   : 73 (1368 bytes)

ack-only packets                            : 320548 (140960 delayed)

URG only packet                             : 0

window probe packet                         : 0

window update packet                        : 0

control packets                             : 32

packets received                            : 658893

acks                                        : 338738 for (7435123 bytes)

duplicate acks                              : 23

ack for unsent data                         : 0

packets received in-sequence                : 334705 (5568368 bytes)

completely duplicate packet                 : 2 (36 bytes)

packet with some dup. data                  : 0 (0 bytes)

out-of-order packets                        : 20 (0 bytes)

packet of data after window                 : 0 (0 bytes)

window probe                                : 0

window update packet                        : 3

packets received after close                : 0

discarded for bad checksum                  : 0

discarded for bad header offset field       : 0

discarded because packet too short          : 0

connection request                          : 4

connection accept                           : 24

connections established (including accepts) : 27

connections closed                          : 26 (including 2 drops)

embryonic connections dropped               : 0

segments updated rtt                        : 338742 (of 338747 attempts)

retransmit timeouts                         : 75

connections dropped by rexmit timeout       : 0

persist timeouts                            : 0

keepalive timeouts                          : 26

keepalive probes sent                       : 0

connections dropped by keepalive            : 1

pcb cache lookups failed                    : 0

connections dropped by bad md5 digest       : 0

connections dropped by enhanced auth        : 0

path mtu discovery backoff                  : 0

===============================================================================

A:ALA-12#

cpu

Syntax

cpu [sample-period seconds]

Context

This command displays CPU utilization per task over a sample period.

show>card

Description

Parameters

sample-period seconds

The number of seconds over which to sample CPU task utilization.

Default

Values

1 — 300

Output

System CPU Output

The following table describes the system CPU output fields.


Label	Description
CPU Utilization	The total amount of CPU time.
Name	The process or protocol name.
CPU Time (uSec)	The CPU time each process or protocol has used in the specified time.
CPU Usage	The sum of CPU usage of all the processes and protocols.
Capacity Usage	Displays the level the specified service is being utilized. When this number hits 100%, this part of the system is busied out. There may be extra CPU cycles still left for other processes, but this service is running at capacity. This column does not reflect the true CPU utilization value; that data is still available in the CPU Usage column. This column is the busiest task in each group, where busiest is defined as either actually running or blocked attempting to acquire a lock.

This command enters the show CRON context.

*A:cses-E11# show system cpu sample-period 2

===============================================================================

CPU Utilization (Sample period: 2 seconds)

===============================================================================

Name                                   CPU Time       CPU Usage        Capacity

                                         (uSec)                           Usage

-------------------------------------------------------------------------------

BFD                                          10          ~0.00%          ~0.00%

BGP                                           0           0.00%           0.00%

CFLOWD                                       61          ~0.00%          ~0.00%

Cards & Ports                             8,332           0.41%           0.08%

DHCP Server                                  79          ~0.00%          ~0.00%

ICC                                         408           0.02%           0.01%

IGMP/MLD                                  1,768           0.08%           0.08%

IOM                                      17,197           0.85%           0.31%

IP Stack                                  4,080           0.20%           0.09%

IS-IS                                     1,213           0.06%           0.06%

ISA                                       2,496           0.12%           0.07%

LDP                                           0           0.00%           0.00%

Logging                                      32          ~0.00%          ~0.00%

MPLS/RSVP                                 2,380           0.11%           0.08%

MSDP                                          0           0.00%           0.00%

Management                                5,969           0.29%           0.15%

OAM                                         907           0.04%           0.02%

OSPF                                         25          ~0.00%          ~0.00%

PIM                                       5,600           0.27%           0.27%

RIP                                           0           0.00%           0.00%

RTM/Policies                                  0           0.00%           0.00%

Redundancy                                3,635           0.18%           0.13%

SIM                                       1,462           0.07%           0.04%

SNMP Daemon                                   0           0.00%           0.00%

Services                                  2,241           0.11%           0.05%

Stats                                         0           0.00%           0.00%

Subscriber Mgmt                           2,129           0.10%           0.04%

System                                    8,802           0.43%           0.17%

Traffic Eng                                   0           0.00%           0.00%

VRRP                                        697           0.03%           0.02%

WEB Redirect                                125          ~0.00%          ~0.00%

-------------------------------------------------------------------------------

Total                                 2,014,761         100.00%

   Idle                               1,945,113          96.54%

   Usage                                 69,648           3.45%

Busiest Core Utilization                 69,648           3.45%

===============================================================================

*A:cses-E11#

*A:ALA-1# show card 4 cpu

===============================================================================

Card 4 CPU Utilization (Sample period: 1 second)

===============================================================================

Name                                   CPU Time       CPU Usage        Capacity

                                         (uSec)                           Usage

-------------------------------------------------------------------------------

HQoS Algorithm                               70          ~0.00%          ~0.00%

HQoS Statistics                             124          ~0.00%           0.83%

IOM                                      15,904           0.79%           0.94%

-------------------------------------------------------------------------------

Total                                 2,003,678         100.00%

   Idle                               1,987,580          99.19%

   Usage                                 16,098           0.80%

Busiest Core Utilization                  8,192           0.81%

===============================================================================

cron

Syntax

cron

Context

show>cron

Description

action

Syntax

action [action-name] [owner action-owner] run-history run-state

Context

show>cron#

Description

This command displays cron action parameters.

Parameters

action action-name

Specifies the action name.

Values

maximum 32 characters

owner action-owner

Specifies the owner name.

Default

TiMOS CLI

run-history run-state

Specifies the state of the test to be run.

Values

executing, initializing, terminated

Output

The following table describes the show cron action output fields.


Label	Description
Action	Displays the name of the action.
Action owner	The name of the action owner.
Administrative status	Enabled Administrative status is enabled Disabled Administrative status is disabled
Script	The name of the script
Script owner	The name of the script owner.
Script source location	Displays the location of scheduled script.
Max running allowed	Displays the maximum number of allowed sessions.
Max completed run histories	Displays the maximum number of sessions previously run.
Max lifetime allowed	Displays the maximum amount of time the script may run.
Completed run histories	Displays the number of completed sessions.
Executing run histories	Displays the number of sessions in the process of executing.
Initializing run histories	Displays the number of sessions ready to run/queued but not executed.
Max time run history saved	Displays the maximum amount of time to keep the results from a script run.
Last change	Displays the system time a change was made to the configuration.

This command displays cron schedule parameters.

*A:Redundancy# show cron action run-history terminated

===============================================================================

CRON Action Run History

===============================================================================

Action "test"

Owner "TiMOS CLI"

-------------------------------------------------------------------------------

Script Run #17

-------------------------------------------------------------------------------

Start time    : 2006/11/06 20:30:09     End time      : 2006/11/06 20:35:24

Elapsed time  : 0d 00:05:15             Lifetime      : 0d 00:00:00

State         : terminated              Run exit code : noError

Result time   : 2006/11/06 20:35:24     Keep history  : 0d 00:49:57

Error time    : never

Results file  : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203008.

out

Run exit      : Success

-------------------------------------------------------------------------------

Script Run #18

-------------------------------------------------------------------------------

Start time    : 2006/11/06 20:35:24     End time      : 2006/11/06 20:40:40

Elapsed time  : 0d 00:05:16             Lifetime      : 0d 00:00:00

State         : terminated              Run exit code : noError

Result time   : 2006/11/06 20:40:40     Keep history  : 0d 00:55:13

Error time    : never

Results file  : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203523.

out

Run exit      : Success

-------------------------------------------------------------------------------

*A:Redundancy#

*A:Redundancy# show cron action run-history executing

===============================================================================

CRON Action Run History

===============================================================================

Action "test"

Owner "TiMOS CLI"

-------------------------------------------------------------------------------

Script Run #20

-------------------------------------------------------------------------------

Start time    : 2006/11/06 20:46:00     End time      : never

Elapsed time  : 0d 00:00:56             Lifetime      : 0d 00:59:04

State         : executing               Run exit code : noError

Result time   : never                   Keep history  : 0d 01:00:00

Error time    : never

Results file  : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-204559.

out

===============================================================================

*A:Redundancy#

*A:Redundancy# show cron action run-history initializing

===============================================================================

CRON Action Run History

===============================================================================

Action "test"

Owner "TiMOS CLI"

-------------------------------------------------------------------------------

Script Run #21

-------------------------------------------------------------------------------

Start time    : never                   End time      : never

Elapsed time  : 0d 00:00:00             Lifetime      : 0d 01:00:00

State         : initializing            Run exit code : noError

Result time   : never                   Keep history  : 0d 01:00:00

Error time    : never

Results file  : none

-------------------------------------------------------------------------------

Script Run #22

-------------------------------------------------------------------------------

Start time    : never                   End time      : never

Elapsed time  : 0d 00:00:00             Lifetime      : 0d 01:00:00

State         : initializing            Run exit code : noError

Result time   : never                   Keep history  : 0d 01:00:00

Error time    : never

Results file  : none

-------------------------------------------------------------------------------

Script Run #23

-------------------------------------------------------------------------------

Start time    : never                   End time      : never

Elapsed time  : 0d 00:00:00             Lifetime      : 0d 01:00:00

State         : initializing            Run exit code : noError

Result time   : never                   Keep history  : 0d 01:00:00

Error time    : never

Results file  : none

===============================================================================

*A:Redundancy#

schedule

Syntax

schedule [schedule-name] [owner schedule-owner]

Context

show>cron#

Description

Parameters

schedule-name

Displays information for the specified scheduler name.

owner schedule-owner

Displays information for the specified scheduler owner.

Output

The following table describes the show cron schedule output fields.


Label	Description
Schedule name	Displays the schedule name.
Schedule owner	Displays the owner name of the action.
Description	Displays the schedule’s description.
Administrative status	Enabled The administrative status is enabled.
	Disabled Administratively disabled.
Operational status	Enabled The operational status is enabled.
	Disabled Operationally disabled.
Action	Displays the action name
Action owner	Displays the name of action owner.
Script	Displays the name of the script.
Script owner	Displays the name of the script.
Script owner	Displays the name of the of script owner.
Script source location	Displays the location of scheduled script.
Script results location	Displays the location where the script results have been sent.
Schedule type	Periodic Displays a schedule which ran at a given interval. Calendar Displays a schedule which ran based on a calendar. Oneshot Displays a schedule which ran one time only.
Interval	Displays the interval between runs of an event.
Next scheduled run	Displays the time for the next scheduled run.
Weekday	Displays the configured weekday.
Month	Displays the configured month.
Day of Month	Displays the configured day of month.
Hour	Displays the configured hour.
Minute	Displays the configured minute.
Number of scheduled runs	Displays the number of scheduled sessions.
Last scheduled run	Displays the last scheduled session.
Number of scheduled failures	Displays the number of scheduled sessions that failed to execute.
Last scheduled failure	Displays the last scheduled session that failed to execute.
Last failure time	Displays the system time of the last failure.

A:sim1>show>cron schedule test

===============================================================================

CRON Schedule Information

===============================================================================

Schedule                     : test

Schedule owner               : TiMOS CLI

Description                  : none

Administrative status        : enabled

Operational status           : enabled

Action                       : test

Action owner                 : TiMOS CLI

Script                       : test

Script Owner                 : TiMOS CLI

Script source location       : ftp://*****:******@192.168.15.1/home/testlab_bgp

                               /cron/test1.cfg

Script results location      : ftp://*****:******@192.168.15.1/home/testlab_bgp

                               /cron/res

Schedule type                : periodic

Interval                     : 0d 00:01:00 (60 seconds)

Next scheduled run           : 0d 00:00:42

Weekday                      : tuesday

Month                        : none

Day of month                 : none

Hour                         : none

Minute                       : none

Number of schedule runs      : 10

Last schedule run            : 2008/01/01 17:20:52

Number of schedule failures  : 0

Last schedule failure        : no error

Last failure time            : never

===============================================================================

A:sim1>show>cron

information

Syntax

information

Context

This command displays general system information including basic system, SNMP server, last boot and DNS client information.

Description

Output

System Information Output

The following table describes the system information output fields.


Label	Description
System Name	The configured system name.
System Contact	A text string that describes the system contact information.
System Location	A text string that describes the system location.
System Coordinates	A text string that describes the system coordinates.
System Up Time	The time since the last boot.
SNMP Port	The port number used by this node to receive SNMP request messages and to send replies.
SNMP Engine ID	The SNMP engineID to uniquely identify the SNMPv3 node.
SNMP Max Message Size	The maximum SNMP packet size generated by this node.
SNMP Admin State	Enabled SNMP is administratively enabled and running. Disabled SNMP is administratively shutdown and not running.

SNMP Oper State	Enabled SNMP is operationally enabled. Disabled SNMP is operationally disabled.

SNMP Index Boot Status	Persistent System indexes are saved between reboots. Not Persistent System indexes are not saved between reboots.

Telnet/SSH/FTP Admin	Displays the administrative state of the Telnet, SSH, and FTP sessions.
Telnet/SSH/FTP Oper	Displays the operational state of the Telnet, SSH, and FTP sessions.
BOF Source	The location of the BOF.
Image Source	Primary Indicates that the directory location for runtime image file was loaded from the primary source.
	Secondary Indicates that the directory location for runtime image file was loaded from the secondary source. Tertiary Indicates that the directory location for runtime image file was loaded from the tertiary source.

Config Source	Primary Indicates that the directory location for configuration file was loaded from the primary source. Secondary Indicates that the directory location for configuration file was loaded from the secondary source. Tertiary Indicates that the directory location for configuration file was loaded from the tertiary source.


DNS Resolve Preference	ipv4-only Dns-names are queried for A-records only. ipv6-first Dns-server will be queried for AAAA-records first and a successful reply is not received, the dns-server is queried for A-records.

Last Booted Config File	The URL and filename of the last loaded configuration file.
Last Boot Cfg Version	The date and time of the last boot.
Last Boot Config Header	Displays header information such as image version, date built, date generated.
Last Boot Index Version	The version of the persistence index file read when this card was last rebooted.
Last Boot Index Header	The header of the persistence index file read when this card was last rebooted.
Last Saved Config	The location and filename of the last saved configuration file.
Time Last Saved	The date and time of the last time configuration file was saved.
Changes Since Last Save	Yes There are unsaved configuration file changes. No There are no unsaved configuration file changes.
Time Last Modified	The date and time of the last modification.
Max Cfg/BOF Backup Rev	The maximum number of backup revisions maintained for a configuration file. This value also applies to the number of revisions maintained for the BOF file.
Cfg-OK Script	URL The location and name of the CLI script file executed following successful completion of the boot-up configuration file execution.
Cfg-OK Script Status	Successful/Failed The results from the execution of the CLI script file specified in the Cfg-OK Script location. Not used No CLI script file was executed.

Cfg-Fail Script	URL The location and name of the CLI script file executed following a failed boot-up configuration file execution. Not used No CLI script file was executed.

Cfg-Fail Script Status	Successful/Failed The results from the execution of the CLI script file specified in the Cfg-Fail Script location. Not used No CLI script file was executed.

Management IP Addr	The management IP address and mask.
DNS Server	The IP address of the DNS server.
DNS Domain	The DNS domain name of the node.
BOF Static Routes	To The static route destination.
	Next Hop The next hop IP address used to reach the destination. Metric Displays the priority of this static route versus other static routes. None No static routes are configured.

A:Dut-F>show system information

...

Primary DNS Server     : 138.120.252.56

Secondary DNS Server   : 138.120.252.48

Tertiary DNS Server    : 138.120.252.49

DNS Domain             : labs.ca.alcatel-lucent.com

DNS Resolve Preference : ipv4-only

DNSSEC                 AD Validated    : False

DNSSEC Response Control: drop

BOF Static Routes      :

A:Dut-F# show system information

===============================================================================

System Information

===============================================================================

System Name            : Dut-F

System Type            : 7750 SR-7 7450 ESS-7

System Version         : B-6.0.B1-6

System Contact         :

System Location        :

System Coordinates     :

System Active Slot     : A

System Up Time         : 0 days, 03:42:01.29 (hr:min:sec)

SNMP Port              : 161

SNMP Engine ID         : 0000197f00008c6cff000000

SNMP Max Message Size  : 1500

SNMP Admin State       : Enabled

SNMP Oper State        : Enabled

SNMP Index Boot Status : Not Persistent

SNMP Sync State        : OK

Tel/Tel6/SSH/FTP Admin : Enabled/Disabled/Enabled/Enabled

Tel/Tel6/SSH/FTP Oper  : Up/Down/Up/Up

BOF Source             : ftp://test:test@xxx.xxx.xx.xxx/./images

Image Source           : primary

Config Source          : primary

Last Booted Config File: ftp://*:*@xxx.xxx.xx.xxx/./images/dut-f.cfg

Last Boot Cfg Version  : N/A

Last Boot Index Version: N/A

Last Saved Config      : N/A

Time Last Saved        : N/A

Changes Since Last Save: No

Max Cfg/BOF Backup Rev : 5

Cfg-OK Script          : ftp://*:*@[3000::8acb:466d]/./images/env.cfg

Cfg-OK Script Status   : failed

Cfg-Fail Script        : N/A

Cfg-Fail Script Status : not used

Management IP Addr     : xxx.xxx.xx.xxx/23

Primary DNS Server     : xxx.xxx.xx.xxx

Secondary DNS Server   : xxx.xxx.xx.xxx

Tertiary DNS Server    : N/A

DNS Domain             : sh.bel.alcatel.be

DNS Resolve Preference : ipv4-only

BOF Static Routes      :

  To                   Next Hop

  138.203.0.0/16       xxx.xxx.xx.xxx

  172.0.0.0/8          xxx.xxx.xx.xxx

ATM Location ID        : 01:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00

ATM OAM Retry Up       : 2

ATM OAM Retry Down     : 4

ATM OAM Loopback Period: 10

===============================================================================

A:Dut-F#

lldp

Syntax

lldp neighbor

Context

This command displays neighbor information for all configured ports without having to specify each individual port ID.

Description

Parameters

neighbor

Displays LLDP neighbor information.

*A:Dut-C# show system lldp neighbor

Link Layer Discovery Protocol (LLDP) System Information

==============================================================================

NB = nearest-bridge   NTMPR = nearest-non-tpmr   NC = nearest-customer

==============================================================================

Port      Scope  Chassis ID           Index    Port ID     System Name

------------------------------------------------------------------------------

1/1/1     NB     16:2f:ff:00:00:00    1        35717120    Dut-A

2/1/2     NB     16:34:ff:00:00:00    1        35782656    Dut-D

2/1/1     NB     16:36:ff:00:00:00    2        35684352    Dut-E

1/1/2     NB     16:30:ff:00:00:00    2        35749888    Dut-B

1/1/3     NB     16:30:ff:00:00:00    3        35782656    Dut-B

2/1/3     NB     16:30:ff:00:00:00    3        35815424    Dut-B

==============================================================================

Number of neighbors : 6

*A:Dut-C#

A:GHR-API# show system lldp neighbor

Link Layer Discovery Protocol (LLDP) System Information

==============================================================================

NB = nearest-bridge   NTMPR = nearest-non-tpmr   NC = nearest-customer

==============================================================================

Port      Scope  Chassis ID           Index    Port ID     System Name

------------------------------------------------------------------------------

1/1/6     NTPMR  00:21:05:1b:bc:17    1        36044800    RXI-AMI

1/1/8     NTPMR  00:21:06:6d:bd:53    2        36110336    YOY-WOW

1/1/9     NTPMR  00:21:08:2b:ab:81    3        36143104    FRI-MON

==============================================================================

Number of neighbors : 3

load-balancing-alg

Syntax

load-balancing-alg [detail]

Context

This command displays system load balancing settings.

Description

Parameters

Displays port settings.

*A:ALA-49>show>system# load-balancing-alg

===============================================================================

System-wide Load Balancing Algorithms

===============================================================================

L4  - Load Balance                     : exclude-L4

LSR - Load Balance                     : lbl-only

===============================================================================

*A:ALA-49>show>system#

Syntax

Context

This command displays system memory status.

Description

Output

Memory Pools Output

The following table describes memory pool output fields.


Label	Description
Name	The name of the system or process.
Max Allowed	Integer The maximum allocated memory size.
	No Limit No size limit.
Current Size	The current size of the memory pool.
Max So Far	The largest amount of memory pool used.
In Use	The current amount of the memory pool currently in use.
Current Total Size	The sum of the Current Size column.
Total In Use	The sum of the In Use column.
Available Memory	The amount of available memory.

A:ALA-1# show system memory-pools

===============================================================================

Memory Pools

===============================================================================

Name               Max Allowed    Current Size      Max So Far          In Use

-------------------------------------------------------------------------------

System                No limit      24,117,248      24,117,248      16,974,832

Icc                  8,388,608       1,048,576       1,048,576          85,200

RTM/Policies          No limit       5,242,912       5,242,912       3,944,104

OSPF                  No limit       3,145,728       3,145,728       2,617,384

MPLS/RSVP             No limit       9,769,480       9,769,480       8,173,760

LDP                   No limit               0               0               0

IS-IS                 No limit               0               0               0

RIP                   No limit               0               0               0

VRRP                  No limit       1,048,576       1,048,576              96

BGP                   No limit       2,097,152       2,097,152       1,624,800

Services              No limit       2,097,152       2,097,152       1,589,824

IOM                   No limit     205,226,800     205,226,800     202,962,744

SIM                   No limit       1,048,576       1,048,576             392

CFLOWD                No limit               0       1,048,576               0

IGMP                  No limit               0               0               0

PIM                   No limit               0               0               0

ATM                   No limit       2,872,648       2,872,648       2,790,104

MMPI                  No limit               0               0               0

MFIB                  No limit               0               0               0

PIP                   No limit      79,943,024      79,943,024      78,895,248

MBUF                67,108,864       5,837,328       5,837,328       4,834,280

-------------------------------------------------------------------------------

Current Total Size :    343,495,200 bytes

Total In Use       :    324,492,768 bytes

Available Memory   :    640,178,652 bytes

===============================================================================

A:ALA-1#

ntp

Syntax

ntp

Context

This command displays NTP protocol configuration and state.

Description

Output

Show NTP Output

The following table describes NTP output fields.


Label	Description
Enabled	yes NTP is enabled.
	no NTP is disabled.
Admin Status	yes Administrative state is enabled.
	no Administrative state is disabled.
NTP Server	Displays NTP server state of this node.
Stratum	Displays stratum level of this node.
Oper Status	yes The operational state is enabled.
	no The operational state is disabled.
Auth Check	Displays the authentication requirement
System Ref. ID	IP address of this node or a 4-character ASCII code showing the state.
Auth Error	Displays the number of authentication errors.
Auth Errors Ignored	Displays the number of authentication errors ignored.
Auth key ID Errors	Displays the number of key identification errors.
Auth Key Type Errors	Displays the number of authentication key type errors.
Reject	The peer is rejected and will not be used for synchronization. Rejection reasons could be the peer is unreachable, the peer is synchronized to this local server so synchronizing with it would create a sync loop, or the synchronization distance is too large. This is the normal startup state.
Invalid	The peer is not maintaining an accurate clock. This peer will not be used for synchronization.
Excess	The peer's synchronization distance is greater than ten other peers. This peer will not be used for synchronization.
Outlyer	The peer is discarded as an outlyer. This peer will not be used for synchronization.
Candidate	The peer is accepted as a possible source of synchronization.
Selected	The peer is an acceptable source of synchronization, but its synchronization distance is greater than six other peers.
Chosen	The peer is chosen as the source of synchronization.
ChosenPPS	The peer is chosen as the source of synchronization, but the actual synchronization is occurring from a pulse-per-second (PPS) signal.
Remote	The IP address of the remote NTP server or peer with which this local host is exchanging NTP packets.
Reference ID	When stratum is between 0 and 15 this field shows the IP address of the remote NTP server or peer with which the remote is exchanging NTP packets. For reference clocks, this field shows the identification assigned to the clock, such as, “.GPS.” For an NTP server or peer, if the client has not yet synchronized to a server/peer, the status cannot be determined and displays the following codes:
	Peer Codes: ACST The association belongs to any cast server. AUTH Server authentication failed. Please wait while the association is restarted. AUTO Autokey sequence failed. Please wait while the association is restarted. BCST The association belongs to a broadcast server. CRPT Cryptographic authentication or identification failed. The details should be in the system log file or the cryptostats statistics file, if configured. No further messages will be sent to the server. DENY Access denied by remote server. No further messages will be sent to the server.
	DROP Lost peer in symmetric mode. Please wait while the association is restarted. RSTR Access denied due to local policy. No further messages will be sent to the server. INIT The association has not yet synchronized for the first time. MCST The association belongs to a manycast server. NKEY No key found. Either the key was never installed or is not trusted. RATE Rate exceeded. The server has temporarily denied access because the client exceeded the rate threshold. RMOT The association from a remote host running ntpdc has had unauthorized attempted access. STEP A step change in system time has occurred, but the association has not yet resynchronized. System Codes INIT The system clock has not yet synchronized for the first time. STEP A step change in system time has occurred, but the system clock has not yet resynchronized.
St	Stratum level of this node.
Auth	yes Authentication is enabled.
	no Authentication is disabled.
Poll	Polling interval in seconds.
R	Yes The NTP peer or server has been reached at least once in the last 8 polls.
	No The NTP peer or server has not been reached at least once in the last 8 polls.
Offset	The time between the local and remote UTC time, in milliseconds.

*A:Dut-A# show system ntp

===============================================================================

NTP Status

===============================================================================

Configured         : Yes                Stratum              : 4

Admin Status       : up                 Oper Status          : up

Server Enabled     : No                 Server Authenticate  : No

Clock Source       : 1111:2222:3333:4444:5555:10:100:2

Auth Check         : Yes

Current Date & Time: 2015/07/10 12:46:30 UTC

===============================================================================

*A:Dut-A# show system ntp all

===============================================================================

NTP Status

===============================================================================

Configured         : Yes                Stratum              : 4

Admin Status       : up                 Oper Status          : up

Server Enabled     : No                 Server Authenticate  : No

Clock Source       : 1111:2222:3333:4444:5555:10:100:2

Auth Check         : Yes

Current Date & Time: 2015/07/10 12:46:32 UTC

===============================================================================

===============================================================================

NTP Active Associations

===============================================================================

State                     Reference ID    St Type  A  Poll Reach     Offset(ms)

    Remote

-------------------------------------------------------------------------------

candidate                 252.242.213.211 3  srvr  -  64   YYYYYYYY  -5.829

    10.10.1.2

candidate                 252.242.213.211 3  srvr  -  64   YYYYYYYY  -6.889

    10.10.100.2

chosen                    252.242.213.211 3  srvr  -  64   ...YYYYY  -6.804

    1111:2222:3333:4444:5555:10:100:2

===============================================================================

===============================================================================

NTP Clients

===============================================================================

vRouter                                                    Time Last Request Rx

    Address

-------------------------------------------------------------------------------

===============================================================================

*A:Dut-A# show system ntp detail

===============================================================================

NTP Status

===============================================================================

Configured         : Yes                Stratum              : 4

Admin Status       : up                 Oper Status          : up

Server Enabled     : No                 Server Authenticate  : No

Clock Source       : 1111:2222:3333:4444:5555:10:100:2

Auth Check         : Yes

Auth Errors        : 0                  Auth Errors Ignored  : 0

Auth Key Id Errors : 0                  Auth Key Type Errors : 0

Current Date & Time: 2015/07/10 12:46:34 UTC

===============================================================================

===============================================================================

NTP Configured Broadcast/Multicast Interfaces

===============================================================================

vRouter         Interface           Address             Type    Auth    Poll

-------------------------------------------------------------------------------

===============================================================================

*A:Dut-A# show system ntp detail all

===============================================================================

NTP Status

===============================================================================

Configured         : Yes                Stratum              : 4

Admin Status       : up                 Oper Status          : up

Server Enabled     : No                 Server Authenticate  : No

Clock Source       : 1111:2222:3333:4444:5555:10:100:2

Auth Check         : Yes

Auth Errors        : 0                  Auth Errors Ignored  : 0

Auth Key Id Errors : 0                  Auth Key Type Errors : 0

Current Date & Time: 2015/07/10 12:46:36 UTC

===============================================================================

===============================================================================

NTP Configured Broadcast/Multicast Interfaces

===============================================================================

vRouter         Interface           Address             Type    Auth    Poll

-------------------------------------------------------------------------------

===============================================================================

===============================================================================

NTP Active Associations

===============================================================================

State                     Reference ID    St Type  A  Poll Reach     Offset(ms)

    Remote

-------------------------------------------------------------------------------

candidate                 252.242.213.211 3  srvr  -  64   YYYYYYYY  -5.829

    10.10.1.2

candidate                 252.242.213.211 3  srvr  -  64   YYYYYYYY  -6.889

    10.10.100.2

chosen                    252.242.213.211 3  srvr  -  64   ...YYYYY  -6.804

    1111:2222:3333:4444:5555:10:100:2

===============================================================================

===============================================================================

NTP Clients

===============================================================================

vRouter                                                    Time Last Request Rx

    Address

-------------------------------------------------------------------------------

===============================================================================

*A:Dut-A#

rollback

Syntax

rollback

Context

This command displays rollback configuration and state.

Description

A:dut-a_a># show system rollback

===============================================================================

Rollback Information

===============================================================================

Rollback Location               : cf1:/Rollback

Save

  Last Rollback Save Result     : In Progress, Successful or Failed

  Last Save Completion Time     : 10/15/2010 21:24:06

Revert

  In Progress                   : Yes, No

  Last Revert Initiated Time    : 10/15/2010 21:26:23

  Last Revert Initiated User    : xyz

  Last Initiated Checkpoint     : cf1:/Rollback.rb.3

  Last Completed Revert Result  : Successful or Failed

  Last Revert Completion  Time  : 10/15/2010 21:27:19

================================================================================

Rollback Files

================================================================================

Idx      Suffix   Creation time        Release  User

           Comment

--------------------------------------------------------------------------------

latest   .rb      2010/10/15 21:24:02  9.0.R4   fred

           This checkpoint was saved after the 3 VPLS services were created

1        .rb.1    2010/10/15 21:23:58  9.0.R4   John

           John’s checkpoint on Sunday

2        .rb.2    2010/10/15 21:23:52  9.0.R4   admin

           A long checkpoint comment that an operator is using to summarize

           various some of the changes that were made.   They may even have so

           much to say that they use the maximum comment size.   Notice that

           words are not chopped.

…

9        .rb.9    2010/10/14 22:00:01  9.0.R4   admin

           VPLS services 1000-2000 created

…

53       .rb.53   2010/10/14 22:10:10  9.0.R4   admin

--------------------------------------------------------------------------------

No. of Rollback Files: 10

================================================================================

ptp

Syntax

ptp [standby]

ptp peers [router router-instance|service-name service-name] [detail]

ptp port

ptp port port-id [detail]

ptp statistics

ptp unicast [router router-instance|service-name service-name]

Context

These commands display Precision Time Protocol (PTP) configuration and state information. This information can be displayed for the entire node or on a per router instance basis.

Description

Parameters

standby

Displays information for PTP on the standby control module.

unicast

Displays information related to the unicast sessions.

Displays the message and error statistics for the node.

peers

Displays summary information for the PTP peers.

Displays information for a single PTP peer.

router router-instance

Qualifier to show only the information for a specific router instance.

Provides additional information on the specified area.

router-instance

router-name|service-id

Values

router-name - "Base"

Values

service-id - [1..2147483647]

Output

Show PTP Output

The following table describes PTP output fields.


Label	Description
Pending	When the SR/ESS has initiated a request to a peer but has not yet received a response.
Granted	When the SR/ESS has initiated a request to a peer and it was granted OR a peer has made a request of the SR/ESS and it was granted.
Denied	When the SR/ESS has initiated a request to a peer but it was rejected.
Canceled	When a cancel message has been received from or transmitted toward a peer.
Expired	When a unicast session between the SR/ESS and the peer has expired without being renewed.

B:NS082761964# show system ptp

===============================================================================

IEEE 1588/PTP Clock Information

===============================================================================

-------------------------------------------------------------------------------

Local Clock

-------------------------------------------------------------------------------

Clock Type        : boundary           PTP Profile         : ITU-T G.8275.1

Domain            : 0                  Network Type        : sdh

Admin State       : up                 Oper State          : up

Announce Interval : 1 pkt/2 s          Announce Rx Timeout : 3 intervals

Peer Limit        : none (Base Router) G.8275.1 Priority   : 128

Clock Id          : 001af0fffeb2fead   Clock Class         : 255 (slave-only)

Clock Accuracy    : 0xfe (unknown)     Clock Variance      : ffff (not computed)

Clock Priority1   : 128                Clock Priority2     : 128

PTP Recovery State: locked             Last Changed        : 08/24/2010 13:17:37

Frequency Offset  : +231.920 ppb

-------------------------------------------------------------------------------

Parent Clock

-------------------------------------------------------------------------------

IP Address        : 2.1.1.1            Router            : Base

Port              : 1/2/8              Remote MAC Address: 01:02:03:04:05:06

Local Clock is Parent Clock

Parent Clock Id   : 001af0fffeab36ad   Parent Port Number: 2

GM Clock Id       : 00b0aefffe011ca6   GM Clock Class    : 13

GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance : 0x6400 (3.7E-09)

GM Clock Priority1: 128                GM Clock Priority2: 128

-------------------------------------------------------------------------------

Time Information

-------------------------------------------------------------------------------

Timescale           : PTP

Current Time        : 2011-08-30 15:31:42.99 UTC

Frequency Traceable : yes

Time Traceable      : yes

Time Source         : gps

==============================================================================

B:NS082761964# show system ptp standby

===============================================================================

IEEE 1588/PTP Clock Information

===============================================================================

-------------------------------------------------------------------------------

Local Clock

-------------------------------------------------------------------------------

Clock Type        : ordinary,slave     PTP Profile         : ieee1588-2008

Domain            : 0

Admin State       : up                 Oper State          : up

Announce Interval : 1 pkt/2 s          Announce Rx Timeout : 3 intervals

Clock Id          : 001af0fffeb2fead   Clock Class         : 255 (slave-only)

Clock Accuracy    : 0xfe (unknown)     Clock Variance      : ffff (not computed)

Clock Priority1   : 128                Clock Priority2     : 128

PTP Port State    : listening          Last Changed        : 02/11/2013 18:09:58

PTP Recovery State: locked             Last Changed        : 08/24/2010 13:17:37

Frequency Offset  : +231.920 ppb

-------------------------------------------------------------------------------

Parent Clock

-------------------------------------------------------------------------------

IP Address        : 2.1.1.1

Parent Clock Id   : 001af0fffeab36ad   Remote PTP Port Number: 2

GM Clock Id       : 00b0aefffe011ca6   GM Clock Class    : 13

GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance : 0x6400 (3.7E-09)

GM Clock Priority1: 128                GM Clock Priority2: 128

-------------------------------------------------------------------------------

Time Information

-------------------------------------------------------------------------------

Timescale           : PTP

Current Time        : 2011-08-30 15:31:42.99 UTC

Frequency Traceable : yes

Time Traceable      : yes

Time Source         : gps

==============================================================================

A:bksim1619# show system ptp statistics

===============================================================================

IEEE 1588/PTP Packet Statistics

===============================================================================

                                                      Input              Output

-------------------------------------------------------------------------------

PTP Packets                                         2910253            2393354

  Announce                                             9015              22682

  Sync                                              1153275             622585

  Follow Up                                               0                  0

  Delay Request                                      594036            1153568

  Delay Response                                    1153044             593614

  Signaling                                             883                905

    Request TLVs                                        428                598

      Announce                                          304                350

      Sync                                               62                124

      Delay Response                                     62                124

    Grant TLVs (Granted)                                514                428

      Announce                                          272                304

      Sync                                              121                 62

      Delay Response                                    121                 62

    Grant TLVs (Rejected)                                 0                  0

      Announce                                            0                  0

      Sync                                                0                  0

      Delay Response                                      0                  0

    Cancel TLVs                                           3                  0

      Announce                                            1                  0

      Sync                                                1                  0

      Delay Response                                      1                  0

    Ack Cancel TLVs                                       0                  3

      Announce                                            0                  1

      Sync                                                0                  1

      Delay Response                                      0                  1

    Other TLVs                                            0                  0

  Other                                                   0                  0

  Event Packets timestamped at port                  215523             215371

  Event Packets timestamped in software                   0                  0

  Discards                                                0                  0

    Bad domain value                                      0                  0

    Alternate Master Flag Set                             0                  0

    Other                                                 0                  0

==============================================================================

===============================================================================

IEEE 1588/PTP Clock Recovery State Statistics

===============================================================================

State                                                                 Seconds

-------------------------------------------------------------------------------

Initial                                                                   136

Acquiring                                                                   0

Phase-Tracking                                                              0

Locked                                                                      0

Hold-over                                                                   0

===============================================================================

===============================================================================

IEEE 1588/PTP Clock Recovery Event Statistics

===============================================================================

Event                                                                   Count

-------------------------------------------------------------------------------

Packet Loss                                                                 0

Excessive Packet Loss                                                       0

Excessive Phase Shift Detected                                              0

Too Much Packet Delay Variation                                             0

===============================================================================

===============================================================================

===============================================================================

IEEE 1588/PTP Message Rates Per Second

===============================================================================

                                                UDP/IP             Ethernet

Packet Type                                 Input    Output     Input    Output

-------------------------------------------------------------------------------

Announce                                        0         0        16         0

Sync                                            0         0        32         0

Follow Up                                       0         0        32         0

Delay Request                                   0         0         0         4

Delay Response                                  0         0         4         0

Other                                           0         0         0         0

-------------------------------------------------------------------------------

Total                                           0         0        84         4

===============================================================================

===============================================================================

*A:bksim1618# show system ptp peers

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router

  IP Address                 Anno Flow Admin State PTP Port State Parent Clock

-------------------------------------------------------------------------------

Base

  1.4.1.21                   tx        n/a         master         no

  1.2.1.20                   rx+tx     up          master         no

  1.3.1.19                   rx        up          slave          yes

  1.1.1.21                   tx        n/a         master         no

-------------------------------------------------------------------------------

No. of PTP Peers: 4

===============================================================================

*A:bksim1618# show system ptp peers router Base

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router

  IP Address                 Anno Flow Admin State PTP Port State Parent Clock

-------------------------------------------------------------------------------

Base

  1.4.1.21                   tx        n/a         master         no

-------------------------------------------------------------------------------

No. of PTP Peers: 1

===============================================================================

*A:bksim1618# show system ptp peers router 1

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router

  IP Address                 Anno Flow Admin State PTP Port State Parent Clock

-------------------------------------------------------------------------------

  1.2.1.20                   rx+tx     up          master         no

  1.3.1.19                   rx        up          slave          yes

-------------------------------------------------------------------------------

No. of PTP Peers: 2

===============================================================================

*A:bksim1618# show system ptp peers detail

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router            : Base

IP Address        : 1.4.1.21           Announce Direction : tx

Admin State       : n/a                G.8275.1 Priority  : 128

Local PTP Port    : 3                  PTP Port State     : master

Clock Id          : ac65fffffe000000   Remote PTP Port    : 1

-------------------------------------------------------------------------------

Router            : 1

IP Address        : 1.2.1.20           Announce Direction : rx+tx

Admin State       : up                 G.8275.1 Priority  : 128

Local PTP Port    : 2                  PTP Port State     : master

Clock Id          : ac5efffffe000000   Remote PTP Port    : 1

Locked Out        : no                 Time Remaining     : n/a

-------------------------------------------------------------------------------

Router            : 1

IP Address        : 1.3.1.19           Announce Direction : rx

Admin State       : up                 G.8275.1 Priority  : 128

Local PTP Port    : 1                  PTP Port State     : slave

Clock Id          : ac5dfffffe000000   Remote PTP Port    : 1

GM Clock Id       : ac5dfffffe000000   GM Clock Class     : 13

GM Clock Accuracy : unknown            GM Clock Variance  : ffff (not computed)

GM Clock Priority1: 0                  GM Clock Priority2 : 128

Steps Removed     : 0                  Parent Clock       : yes

Locked Out        : no                 Time Remaining     : n/a

-------------------------------------------------------------------------------

Router            : 2

IP Address        : 1.1.1.21           Announce Direction : tx

Admin State       : n/a                G.8275.1 Priority  : 128

Local PTP Port    : 4                  PTP Port State     : master

Clock Id          : ac65fffffe000000   Remote PTP Port    : 1

===============================================================================

*A:bksim1618# show system ptp peers router 1 detail

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router            : 1

IP Address        : 1.2.1.20           Announce Direction : rx+tx

Admin State       : up                 G.8275.1 Priority  : 128

Local PTP Port    : 2                  PTP Port State     : master

Clock Id          : ac5efffffe000000   Remote PTP Port    : 1

-------------------------------------------------------------------------------

Router            : 1

IP Address        : 1.3.1.19           Announce Direction : rx

Admin State       : up                 G.8275.1 Priority  : 128

Local PTP Port    : 1                  PTP Port State     : slave

Clock Id          : ac5dfffffe000000   Remote PTP Port    : 1

GM Clock Id       : ac5dfffffe000000   GM Clock Class     : 13

GM Clock Accuracy : unknown            GM Clock Variance  : ffff (not computed)

GM Clock Priority1: 0                  GM Clock Priority2 : 128

Steps Removed     : 0                  Parent Clock       : yes

===============================================================================

A:bksim1620# show system ptp peer 6.1.1.2 router 5

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router            : 5

IP Address        : 6.1.1.2            Announce Direction : rx+tx

Admin State       : up                 G.8275.1 Priority  : 128

Local PTP Port    : 2                  PTP Port State     : passive

Clock Id          : ac5dfffffe000000   Remote PTP Port    : 2

GM Clock Id       : ac5cfffffe000000   GM Clock Class     : 13

GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance  : ffff (not computed)

GM Clock Priority1: 128                GM Clock Priority2 : 128

Steps Removed     : 1                  Parent Clock       : no

===============================================================================

A:bksim1620# show system ptp peer 6.1.1.2 router 5 detail

===============================================================================

IEEE 1588/PTP Peer Information

===============================================================================

Router Instance   : 5

IP Address        : 6.1.1.2            Announce Direction : rx+tx

Admin State       : up                 G.8275.1 Priority  : 128

Local PTP Port    : 2                  PTP Port State     : passive

Clock Id          : ac5dfffffe000000   Remote PTP Port    : 2

GM Clock Id       : ac5cfffffe000000   GM Clock Class     : 13

GM Clock Accuracy : 0xfe (unknown)     GM Clock Variance  : ffff (not computed)

GM Clock Priority1: 128                GM Clock Priority2 : 128

Steps Removed     : 1                  Parent Clock       : no

===============================================================================

===============================================================================

IEEE 1588/PTP Unicast Negotiation Information

===============================================================================

IP Address      Dir Type       Rate       Duration State    Time

-------------------------------------------------------------------------------

6.1.1.2         Rx  Announce   1 pkt/2 s  300      Granted  09/01/2010 17:23:04

6.1.1.2         Tx  Announce   1 pkt/2 s  300      Granted  09/01/2010 17:23:04

===============================================================================

===============================================================================

IEEE 1588/PTP Packet Statistics

===============================================================================

                                                      Input              Output

-------------------------------------------------------------------------------

PTP Packets                                                      253         11

  Announce                                                       243          1

  Sync                                                             0          0

  Follow Up                                                        0          0

  Delay Request                                                    0          0

  Delay Response                                                   0          0

  Signaling                                                       10         10

    Request TLVs                                                   6          4

      Announce                                                     6          4

      Sync                                                         0          0

      Delay Response                                               0          0

    Grant TLVs (Granted)                                           4          6

      Announce                                                     4          6

      Sync                                                         0          0

      Delay Response                                               0          0

    Grant TLVs (Rejected)                                          0          0

      Announce                                                     0          0

      Sync                                                         0          0

      Delay Response                                               0          0

    Cancel TLVs                                                    0          0

      Announce                                                     0          0

      Sync                                                         0          0

      Delay Response                                               0          0

    Ack Cancel TLVs                                                0          0

      Announce                                                     0          0

      Sync                                                         0          0

      Delay Response                                               0          0

    Other TLVs                                                     0          0

  Other                                                            0          0

Discards                                                           0          0

  Bad PTP domain                                                   0          0

  Alternate Master                                                 0          0

  Out Of Sequence                                                  0          0

  Peer Disabled                                                    0          0

  Other                                                            0          0

================================================================================

A:bksim1618# show system ptp port 1/1/1 detail

===============================================================================

IEEE 1588/PTP Ethernet Port Information

===============================================================================

Port                : 1/1/2

PTP Admin State     : up                 PTP Oper State     : up

Local MAC Addr      : 02:43:BA:01:00:03  Multicast MAC Addr : 01:1b:19:00:00:00

G.8275.1 notSlave   : false              G.8275.1 Priority  : 128

PTP Port Number     : 3                  PTP Port State     : Slave

Cfg Anno Rate       : 1 pkt/2 s          Cfg Sync/Dly Rate  : 64 pkt/s

Neighbor Clocks     : 4                  Timestamp Point    : port

===============================================================================

A:bksim1618# show system ptp port 1/1/2 detail

===============================================================================

IEEE 1588/PTP Ethernet Port Information

===============================================================================

Port              : 1/1/2

PTP Admin State   : up                 PTP Oper State     : up

Local MAC Addr    : a0:f3:e4:33:ee:a3  Multicast MAC Addr : 01:1b:19:00:00:00

PTP Port Number   : 1                  PTP Port State     : slave

Cfg Anno Rate     : 1 pkt/2 s          Cfg Sync/Delay Rate: 64 pkt/s

Neighbors         : 1                  Timestamp Point    : cpm

===============================================================================

===========================================================

IEEE 1588/PTP Ethernet Port Neighbor Clocks

===========================================================

MAC Address       Clock Id          Port #  Rx Packet Rate

-----------------------------------------------------------

8c:90:d3:c4:3d:f9 a0f3e4fffe637e30       1             128

8c:90:d3:c4:3d:fa a0f3e4fffe637e30       2              64

-----------------------------------------------------------

No. of Neighbor Clocks: 2

===========================================================

===============================================================================

IEEE 1588/PTP Ethernet Port Packet Statistics

===============================================================================

                                                               Input     Output

-------------------------------------------------------------------------------

PTP Packets                                                     3584       1785

  Announce                                                        14          0

  Sync                                                          1785          0

  Follow Up                                                        0          0

  Delay Request                                                    0       1785

  Delay Response                                                1785          0

  Signaling                                                        0          0

  Other                                                            0          0

Discards                                                           0          0

  Bad PTP domain                                                   0          0

  Alternate Master                                                 0          0

  Out Of Sequence                                                  0          0

  Other                                                            0          0

===============================================================================

===============================================================================

IEEE 1588/PTP Ethernet Port Neighbor Clocks

===============================================================================

  MAC Address          Clock Id           Port Num     Rx Packet Rate

-------------------------------------------------------------------------------

  01:02:03:04:05:06    ac65fffffe000001      65535           64

  01:02:03:04:05:07    ac65fffffe000002          1            0

  01:02:03:04:05:08    ac65fffffe000003          2           64

  01:02:03:04:05:09    ac65fffffe000004         99            0

===============================================================================

===============================================================================

IEEE 1588/PTP Ethernet Port Packet Statistics

===============================================================================

                                                      Input              Output

-------------------------------------------------------------------------------

PTP Packets                                                      253         11

  Announce                                                       243          1

  Sync                                                             0          0

  Follow Up                                                        0          0

  Delay Request                                                    0          0

  Delay Response                                                   0          0

  Signaling                                                       10         10

  Other                                                            0          0

Discards                                                           0          0

  Bad PTP domain                                                   0          0

  Alternate Master                                                 0          0

  Out Of Sequence                                                  0          0

  Other                                                            0          0

================================================================================

A:bksim1618# show system ptp port

===============================================================================

IEEE 1588/PTP Ethernet Port Summary Information

===============================================================================

Port       PTP Adm/Opr   PTP State    Neighbors   Tx Rate     Rx Rate

-------------------------------------------------------------------------------

10/2/16       up/up         passive         5          12312       4400

1/1/1         up/up         slave           1          12312       4400

1/1/2         up/up         master         61          12312       4400

1/1/3         up/down       disabled        0              0          0

1/1/4         up/up         listening       0              0          0

-------------------------------------------------------------------------------

No. of PTP Ports : 5                            Total  99999     999999

*A:bksim1618# show system ptp unicast

===============================================================================

IEEE 1588/PTP Unicast Negotiation Information

===============================================================================

Router

  IP Address      Dir Type     Rate       Duration State    Time

-------------------------------------------------------------------------------

Base

  1.4.1.21        Tx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:14:09

  1.2.1.20        Rx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:14:19

  1.2.1.20        Tx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:13:25

  1.2.1.20        Tx  Sync     64 pkt/s   300      Granted  04/21/2013 19:13:30

  1.2.1.20        Rx  DelayReq 64 pkt/s   300      Granted  04/21/2013 19:13:30

  1.2.1.20        Tx  DelayRsp 64 pkt/s   300      Granted  04/21/2013 19:13:30

  1.3.1.19        Rx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:13:16

  1.3.1.19        Rx  Sync     64 pkt/s   300      Granted  04/21/2013 19:13:21

  1.3.1.19        Tx  DelayReq 64 pkt/s   300      Granted  04/21/2013 19:13:21

  1.3.1.19        Rx  DelayRsp 64 pkt/s   300      Granted  04/21/2013 19:13:21

  1.1.1.21        Tx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:14:08

  1.1.1.21        Tx  Sync     64 pkt/s   300      Granted  04/21/2013 19:14:15

  1.1.1.21        Rx  DelayReq 64 pkt/s   300      Granted  04/21/2013 19:14:15

  1.1.1.21        Tx  DelayRsp 64 pkt/s   300      Granted  04/21/2013 19:14:15

-------------------------------------------------------------------------------

PTP Peers               : 4

Total Packet Rate       : 578 packets/second

===============================================================================

*A:bksim1618#

A:bksim1618# show system ptp router 1 unicast

===============================================================================

IEEE 1588/PTP Unicast Negotiation Information

===============================================================================

Router

  IP Address      Dir Type     Rate       Duration State    Time

-------------------------------------------------------------------------------

  1.2.1.20        Rx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:14:19

  1.2.1.20        Tx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:13:25

  1.2.1.20        Tx  Sync     64 pkt/s   300      Granted  04/21/2013 19:13:30

  1.2.1.20        Rx  DelayReq 64 pkt/s   300      Granted  04/21/2013 19:13:30

  1.2.1.20        Tx  DelayRsp 64 pkt/s   300      Granted  04/21/2013 19:13:30

  1.3.1.19        Rx  Announce 1 pkt/2 s  300      Granted  04/21/2013 19:13:16

  1.3.1.19        Rx  Sync     64 pkt/s   300      Granted  04/21/2013 19:13:21

  1.3.1.19        Tx  DelayReq 64 pkt/s   300      Granted  04/21/2013 19:13:21

  1.3.1.19        Rx  DelayRsp 64 pkt/s   300      Granted  04/21/2013 19:13:21

-------------------------------------------------------------------------------

PTP Peers               : 2

Total Packet Rate       : 385 packets/second

===============================================================================

*A:bksim1618#

sntp

Syntax

sntp

Context

This command displays SNTP protocol configuration and state.

Description

Output

Show SNTP Output

The following table describes SNTP output fields.


Label	Description
SNTP Server	The SNTP server address for SNTP unicast client mode.
Version	The SNTP version number, expressed as an integer.
Preference	Normal When more than one time server is configured, one server can be configured to have preference over another.
Preference	Preferred Indicates that this server has preference over another.
Interval	The frequency, in seconds, that the server is queried.

A:ALA-1# show system sntp

===============================================================================

SNTP

===============================================================================

SNTP Server            Version            Preference         Interval

-------------------------------------------------------------------------------

10.10.20.253           3                  Preferred          64

===============================================================================

A:ALA-1#

thresholds

Syntax

thresholds

Context

This command display system monitoring thresholds. The “Threshold Events Log” table will keep only the last 201 entries.

Description

Output

Thresholds Output

following table describes system threshold output fields.


Label	Description
Variable	Displays the variable OID.
Alarm Id	Displays the numerical identifier for the alarm.
Last Value	Displays the last threshold value.
Rising Event Id	Displays the identifier of the RMON rising event.
Threshold	Displays the identifier of the RMON rising threshold.
Falling Event Id	Displays the identifier of the RMON falling event.
Threshold	Displays the identifier of the RMON falling threshold.
Sample Interval	Displays the polling interval, in seconds, over which the data is sampled and compared with the rising and falling thresholds.
Sample Type	Displays the method of sampling the selected variable and calculating the value to be compared against the thresholds.
Startup Alarm	Displays the alarm that may be sent when this alarm is first created.
Owner	Displays the owner of this alarm.
Description	Displays the event cause.
Event Id	Displays the identifier of the threshold event.
Last Sent	Displays the date and time the alarm was sent.
Action Type	log — An entry is made in the RMON-MIB log table for each event occurrence. This does not create a TiMOS logger entry. The RMON-MIB log table entries can be viewed using the show>system>thresholds CLI command. trap — A TiMOS logger event is generated. The TiMOS logger utility then distributes the notification of this event to its configured log destinations which may be CONSOLE, telnet session, memory log, cflash file, syslog, or SNMP trap destinations logs. both — Both a entry in the RMON-MIB logTable and a TiMOS logger event are generated. none — No action is taken
Owner	Displays the owner of the event.

A:ALA-48# show system thresholds

================================================================

Threshold Alarms

================================================================

Variable: tmnxCpmFlashUsed.1.11.1

Alarm Id         : 1        Last Value : 835

Rising Event Id  : 1        Threshold  : 5000

Falling Event Id : 2        Threshold  : 2500

Sample Interval  : 2147483* SampleType : absolute

Startup Alarm    : either   Owner      : TiMOS CLI

Variable: tmnxCpmFlashUsed.1.11.1

Alarm Id         : 2        Last Value : 835

Rising Event Id  : 3        Threshold  : 10000

Falling Event Id : 4        Threshold  : 5000

Sample Interval  : 2147483* SampleType : absolute

Startup Alarm    : rising   Owner      : TiMOS CLI

Variable: sgiMemoryUsed.0

Alarm Id         : 3        Last Value : 42841056

Rising Event Id  : 5        Threshold  : 4000

Falling Event Id : 6        Threshold  : 2000

Sample Interval  : 2147836  SampleType : absolute

Startup Alarm    : either   Owner      : TiMOS CLI

================================================================

* indicates that the corresponding row element may have been truncated.

================================================================

Threshold Events

================================================================

Description: TiMOS CLI - cflash capacity alarm rising event

Event Id         : 1        Last Sent  : 10/31/2006 08:47:59

Action Type      : both     Owner      : TiMOS CLI

Description: TiMOS CLI - cflash capacity alarm falling event

Event Id         : 2        Last Sent  : 10/31/2006 08:48:00

Action Type      : both     Owner      : TiMOS CLI

Description: TiMOS CLI - cflash capacity warning rising event

Event Id         : 3        Last Sent  : 10/31/2006 08:47:59

Action Type      : both     Owner      : TiMOS CLI

Description: TiMOS CLI - cflash capacity warning falling event

Event Id         : 4        Last Sent  : 10/31/2006 08:47:59

Action Type      : both     Owner      : TiMOS CLI

Description: TiMOS CLI - memory usage alarm rising event

Event Id         : 5        Last Sent  : 10/31/2006 08:48:00

Action Type      : both     Owner      : TiMOS CLI

Description: TiMOS CLI - memory usage alarm falling event

Event Id         : 6        Last Sent  : 10/31/2006 08:47:59

Action Type      : both     Owner      : TiMOS CLI

================================================================

Threshold Events Log

================================================================

Description      : TiMOS CLI - cflash capacity alarm falling eve

                   nt : value=835, <=2500 : alarm-index 1, event

                   -index 2 alarm-variable OID tmnxCpmFlashUsed.

                   1.11.1

Event Id         : 2        Time Sent  : 10/31/2006 08:48:00

Description      : TiMOS CLI - memory usage alarm rising event :

                    value=42841056, >=4000 : alarm-index 3, even

                   t-index 5 alarm-variable OID sgiMemoryUsed.0

Event Id         : 5        Time Sent  : 10/31/2006 08:48:00

================================================================

A:ALA-48#

Syntax

Context

This command displays the system time and zone configuration parameters.

Description

Output

System Time Output

The following table describes system time output fields.


Label	Description
Date & Time	The system date and time using the current time zone.
DST Active	Yes Daylight Savings Time is currently in effect.
	No Daylight Savings Time is not currently in effect.
Zone	The zone names for the current zone, the non-DST zone, and the DST zone if configured.
Current Time Zone	Indicates the process currently controlling the system time. SNTP, NTP, PTP or NONE.
Zone type	Non-standard The zone is user-defined.
	Standard The zone is system defined.
Offset from UTC	The number of hours and minutes added to universal time for the zone, including the DST offset for a DST zone.
Offset from Non-DST	The number of hours (always 0) and minutes (0—60) added to the time at the beginning of Daylight Saving Time and subtracted at the end Daylight Saving Time.
Starts	The date and time Daylight Saving Time begins.
Ends	The date and time Daylight Saving Time ends.

A:ALA-1# show system time

===============================================================================

Date & Time

===============================================================================

Current Date & Time : 2006/05/05 23:03:13    DST Active            : yes

Current Zone        : PDT                    Offset from UTC       : -7:00

-------------------------------------------------------------------------------

Non-DST Zone        : PST                    Offset from UTC       : -8:00

Zone type           : standard

-------------------------------------------------------------------------------

DST Zone            : PDT                    Offset from Non-DST   : 0:60

Starts              : first sunday in april 02:00

Ends                : last sunday in october 02:00

============================================================================

A:ALA-1#

A:ALA-1# show system time (with no DST zone configured)

===============================================================================

Date & Time

===============================================================================

Current Date & Time : 2006/05/12 11:12:05	       DST Active      :     no

Current Zone	    : APA			       Offset from UTC :  -8:00

-------------------------------------------------------------------------------

Non-DST Zone	    : APA			       Offset from UTC :  -8:00

Zone Type           : non-standard

-------------------------------------------------------------------------------

No DST zone configured

===============================================================================

A:ALA-1#

Syntax

This command displays the current day, date, time and time zone.

Context

show

Description

The time is displayed either in the local time zone or in UTC depending on the setting of the root level time-display command for the console session.

Output

tod-suite failed-associations

A:ALA-49# show time

Tue Oct 31 12:17:15 GMT 2006

tod-suite

Syntax

tod-suite [detail]

tod-suite associations

Context

show>cron

Description

This command displays information on the configured time-of-day suite.

Output

CRON TOD Suite Output

The following table describes TOD suite output fields:


Label	Description
Associations	Shows which SAPs this tod-suite is associated with.
failed-associations	Shows the SAPs or Multiservice sites where the TOD Suite could not be applied successfully.
Detail	Shows the details of this tod-suite.

The following example shows output for TOD suite associations.

A:kerckhot_4# show cron tod-suite suite_sixteen detail

===============================================================================

Cron tod-suite details

===============================================================================

Name        : suite_sixteen

Type / Id                        Time-range                       Prio  State

-------------------------------------------------------------------------------

Ingress Qos Policy

  1160                           day                              5     Inact

  1190                           night                            6     Activ

Ingress Scheduler Policy

  SchedPolCust1_Day              day                              5     Inact

  SchedPolCust1_Night            night                            6     Activ

Egress Qos Policy

  1160                           day                              5     Inact

  1190                           night                            6     Activ

Egress Scheduler Policy

  SchedPolCust1Egress_Day        day                              5     Inact

===============================================================================

A:kerckhot_4#

A:kerckhot_4# show cron tod-suite suite_sixteen associations

===============================================================================

Cron tod-suite associations for suite suite_sixteen

===============================================================================

Service associations

-------------------------------------------------------------------------------

Service Id  : 1                         Type   : VPLS

 SAP 1/1/1:1

 SAP 1/1/1:2

 SAP 1/1/1:3

 SAP 1/1/1:4

 SAP 1/1/1:5

 SAP 1/1/1:6

 SAP 1/1/1:20

-------------------------------------------------------------------------------

Number of SAP's : 7

Customer Multi-Service Site associations

-------------------------------------------------------------------------------

Multi Service Site: mss_1_1

-------------------------------------------------------------------------------

Number of MSS's: 1

===============================================================================

A:kerckhot_4#

The following example shows output for TOD suite failed-associations.

A:kerckhot_4# show cron tod-suite suite_sixteen failed-associations

===============================================================================

Cron tod-suite associations failed

===============================================================================

tod-suite suite_sixteen : failed association for SAP

-------------------------------------------------------------------------------

Service Id  : 1                         Type   : VPLS

  SAP 1/1/1:2

  SAP 1/1/1:3

  SAP 1/1/1:4

  SAP 1/1/1:5

  SAP 1/1/1:6

  SAP 1/1/1:20

-------------------------------------------------------------------------------

tod-suite suite_sixteen : failed association for Customer MSS

-------------------------------------------------------------------------------

None

-------------------------------------------------------------------------------

Number of tod-suites failed/total : 1/1

===============================================================================

A:kerckhot_4#

Zooming in on one of the failed SAPs, the assignments of QoS and scheduler policies are shown as not as intended:

A:kerckhot_4# show service id 1 sap 1/1/1:2

===============================================================================

Service Access Points(SAP)

===============================================================================

Service Id         : 1

SAP                : 1/1/1:2                  Encap             : q-tag

Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100

Admin State        : Up                       Oper State        : Up

Flags              : None

Last Status Change : 10/05/2006 18:11:34

Last Mgmt Change   : 10/05/2006 22:27:48

Max Nbr of MAC Addr: No Limit                 Total MAC Addr    : 0

Learned MAC Addr   : 0                        Static MAC Addr   : 0

Admin MTU          : 1518                     Oper MTU          : 1518

Ingress qos-policy : 1130                     Egress qos-policy : 1130

Intend Ing qos-pol*: 1190                     Intend Egr qos-po*: 1190

Shared Q plcy      : n/a                      Multipoint shared : Disabled

Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a

Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a

Ingr IPv6 Fltr-Id  : n/a                      Egr IPv6 Fltr-Id  : n/a

tod-suite          : suite_sixteen            qinq-pbit-marking : both

Egr Agg Rate Limit : max

ARP Reply Agent    : Unknown                  Host Conn Verify  : Disabled

Mac Learning       : Enabled                  Discard Unkwn Srce: Disabled

Mac Aging          : Enabled                  Mac Pinning       : Disabled

L2PT Termination   : Disabled                 BPDU Translation  : Disabled

Multi Svc Site     : None

I. Sched Pol       : SchedPolCust1

Intend I Sched Pol : SchedPolCust1_Night

E. Sched Pol       : SchedPolCust1Egress

Intend E Sched Pol : SchedPolCust1Egress_Night

Acct. Pol          : None                     Collect Stats     : Disabled

Anti Spoofing      : None                     Nbr Static Hosts  : 0

===============================================================================

A:kerckhot_4#

If a time-range is specified for a filter entry, use the show filter command to view results:

A:kerckhot_4# show filter ip  10

===============================================================================

IP Filter

===============================================================================

Filter Id    : 10                               Applied        : No

Scope        : Template                         Def. Action    : Drop

Entries      : 2

-------------------------------------------------------------------------------

Filter Match Criteria : IP

-------------------------------------------------------------------------------

Entry        : 1010

time-range   : day                              Cur. Status    : Inactive

Log Id       : n/a

Src. IP      : 0.0.0.0/0                        Src. Port      : None

Dest. IP     : 10.10.100.1/24                   Dest. Port     : None

Protocol     : Undefined                        Dscp           : Undefined

ICMP Type    : Undefined                        ICMP Code      : Undefined

Fragment     : Off                              Option-present : Off

Sampling     : Off                              Int. Sampling  : On

IP-Option    : 0/0                              Multiple Option: Off

TCP-syn      : Off                              TCP-ack        : Off

Match action : Forward

Next Hop     : 138.203.228.28

Ing. Matches : 0                                Egr. Matches   : 0

Entry        : 1020

time-range   : night                            Cur. Status    : Active

Log Id       : n/a

Src. IP      : 0.0.0.0/0                        Src. Port      : None

Dest. IP     : 10.10.1.1/16                     Dest. Port     : None

Protocol     : Undefined                        Dscp           : Undefined

ICMP Type    : Undefined                        ICMP Code      : Undefined

Fragment     : Off                              Option-present : Off

Sampling     : Off                              Int. Sampling  : On

IP-Option    : 0/0                              Multiple Option: Off

TCP-syn      : Off                              TCP-ack        : Off

Match action : Forward

Next Hop     : 172.22.184.101

Ing. Matches : 0                                Egr. Matches   : 0

===============================================================================

A:kerckhot_4#

If a filter is referred to in a TOD Suite assignment, use the show filter associations command to view the output:

A:kerckhot_4# show filter ip 160 associations

===============================================================================

IP Filter

===============================================================================

Filter Id    : 160                              Applied        : No

Scope        : Template                         Def. Action    : Drop

Entries      : 0

-------------------------------------------------------------------------------

Filter Association : IP

-------------------------------------------------------------------------------

Tod-suite "english_suite"

 - ingress, time-range "day" (priority 5)

===============================================================================

A:kerckhot_4#

Syntax

This command enables the context to show redundancy information.

Context

show

Description

Syntax

This feature is not supported on 7750 SR-a, 7750 SR-c or VSR platforms.

Context

show>redundancy

Description

This command shows the management Ethernet port redundancy status. The show router “management” interface command also shows the CPM Ethernet port used by the management interface. If the primary CPM’s port is active, then it shows “A/1” under the Port field,. If the secondary CPM’s port is active, then it shows “B/1 -> A/1”in the Port field.

Output

Show Redundancy Mgmt-Ethernet Output

The following table describes the Redundancy Mgmt-Ethernet fields:


Label	Description
Admin Status	Enabled — Administrative status is enabled. Disabled — Administratively disabled.
Oper Status	Displays the CPM on which the management Ethernet port is operating.
Revert Time	Displays the revert time.

Show Router “Management” Interface Detail Output

A:SR12# show redundancy mgmt-ethernet

===============================================================================

Management Ethernet Redundancy

===============================================================================

Admin Status  : Enabled

Oper Status   : Management port operating on active CPM

Revert Time   : 5 seconds

===============================================================================

The following is a sample output that shows “A/1” when the primary CPM’s Ethernet port is acitve and “B/1 ->A/1” if the secondary CPM’s port is active.

*B:Dut-A# show router "management" interface

===========================================================================

Interface Table (Router: management)

===========================================================================

Interface-Name                   Adm         Opr(v4/v6)  Mode    Port/SapId

   IP-Address                                                    PfxState

---------------------------------------------------------------------------

management                       Up          Up/Up       Network B/1 -> A/1

   138.120.186.219/24                                            n/a

   3000::8a78:badb/96                                            PREFERRED

   fe80::221:5ff:fece:df49/64                                    PREFERRED

---------------------------------------------------------------------------

Interfaces : 1

===========================================================================

*B:Dut-A# show router "management" interface detail

===============================================================================

Interface Table (Router: management)

===============================================================================

-------------------------------------------------------------------------------

Interface

-------------------------------------------------------------------------------

If Name          : management

Admin State      : Up                   Oper (v4/v6)      : Up/Up

Protocols        : None

IP Addr/mask     : 138.120.186.219/24   Address Type      : Primary

IGP Inhibit      : Disabled             Broadcast Address : Host-ones

HoldUp-Time      : 0                    Track Srrp Inst   : 0

IPv6 Address     : 3000::8a78:badb/96

IPv6 Addr State  : PREFERRED

CGA modifier     : (Not Specified)

HoldUp-Time      : 0                    Track Srrp Inst   : 0

Link Lcl Address : fe80::221:5ff:fece:df49/64

Link Lcl State   : PREFERRED

-------------------------------------------------------------------------------

Details

-------------------------------------------------------------------------------

Description      : (Not Specified)

If Index         : 1280                 Virt. If Index    : 1280

Last Oper Chg    : 06/16/2015 21:01:07  Global If Index   : 16384

Lag Link Map Prof: none

Port Id          : B/1 -> A/1

TOS Marking      : Trusted              If Type           : Network

Egress Filter    : none                 Ingress Filter    : none

Egr IPv6 Flt     : none                 Ingr IPv6 Flt     : none

BGP IP FlowSpec  : Disabled

BGP IPv6 FlowSpec: Disabled

SNTP B.Cast      : True                 Network QoS Policy: 1

MAC Address      : 00:21:05:ce:df:49    Mac Accounting    : Disabled

Syntax

This command enables the context to show multi-chassis redundancy information.

Context

show>redundancy

Description

all

Syntax

all [detail]

Context

This command displays brief multi-chassis redundancy information.

Description

Parameters

Shows detailed multi-chassis redundancy information.

Output

Show Redundancy Multi-Chassis All Output

The following table describes Redundancy Multi-Chassis All fields:


Label	Description
Peer IP Address	Displays the multi-chassis redundancy peer.
Description	The text string describing the peer.
Authentication	If configured, displays the authentication key used between this node and the MC peer.
Source IP Address	Displays the source address used to communicate with the MC peer.
Admin State	Displays the administrative state of the peer.

B:Dut-B# show redundancy multi-chassis all

===============================================================================

Multi-chassis Peer Table

===============================================================================

Peer

-------------------------------------------------------------------------------

Peer IP Address         : 10.10.10.2

Description             : Mc-Lag peer 10.10.10.2

Authentication          : Disabled

Source IP Address       : 0.0.0.0

Admin State             : Enabled

===============================================================================

B:Dut-B#

B:Dut-B# show lag detail

===============================================================================

LAG Details

===============================================================================

LAG 1

-------------------------------------------------------------------------------

Description: Description For LAG Number 1

-------------------------------------------------------------------------------

Details

-------------------------------------------------------------------------------

Lag-id              : 1                     Mode                 : access

Adm                 : up                    Opr                  : up

Thres. Exceeded Cnt : 9                     Port Threshold       : 0

Thres. Last Cleared : 05/20/2006 00:12:35   Threshold Action     : down

Dynamic Cost        : false                 Encap Type           : null

Configured Address  : 1c:71:ff:00:01:41     Lag-IfIndex          : 1342177281

Hardware Address    : 1c:71:ff:00:01:41     Adapt Qos            : distribute

Hold-time Down      : 0.0 sec

LACP                : enabled               Mode                 : active

LACP Transmit Intvl : fast                  LACP xmit stdby      : enabled

Selection Criteria  : highest-count         Slave-to-partner     : disabled

Number of sub-groups: 1                     Forced               : -

System Id           : 1c:71:ff:00:00:00     System Priority      : 32768

Admin Key           : 32768                 Oper Key             : 32666

Prtr System Id      : 20:f4:ff:00:00:00     Prtr System Priority : 32768

Prtr Oper Key       : 32768

MC Peer Address     : 10.10.10.2            MC Peer Lag-id       : 1

MC System Id        : 00:00:00:33:33:33     MC System Priority   : 32888

MC Admin Key        : 32666                 MC Active/Standby    : active

MC Lacp ID in use   : true                  MC extended timeout  : false

MC Selection Logic  : peer decided

MC Config Mismatch  : no mismatch

-------------------------------------------------------------------------------

Port-id        Adm    Act/Stdby Opr    Primary   Sub-group     Forced   Prio

-------------------------------------------------------------------------------

331/2/1          up     active    up     yes       1             -        32768

331/2/2          up     active    up               1             -        32768

331/2/3          up     active    up               1             -        32768

331/2/4          up     active    up               1             -        32768

-------------------------------------------------------------------------------

Port-id        Role      Exp   Def   Dist  Col   Syn   Aggr  Timeout  Activity

-------------------------------------------------------------------------------

331/2/1          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/1          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/2          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/2          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/3          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/3          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/4          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes

331/2/4          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes

===============================================================================

B:Dut-B#

mc-endpoint

Syntax

mc-endpoint statistics

mc-endpoint peer [ip-address] statistics

mc-endpoint endpoint [mcep-id] statistics

mc-endpoint peer [ip-address]

Context

This command displays multi-chassis endpoint information.

Description

Parameters

Displays the global statistics for the MC endpoint.

peer ip-address

Specifies the IP address of multi-chassis end-point peer.

endpoint mcep-id

Specifies the nulti-chassis endpoint.

Values

1 — 4294967295

*A:Dut-B# show redundancy multi-chassis mc-endpoint statistics

===============================================================================

Multi-Chassis Endpoint Global Statistics

===============================================================================

Packets Rx                                  : 533

Packets Rx Keepalive                        : 522

Packets Rx Config                           : 3

Packets Rx Peer Config                      : 1

Packets Rx State                            : 7

Packets Dropped Keep-Alive Task             : 7

Packets Dropped Too Short                   : 0

Packets Dropped Verify Failed               : 0

Packets Dropped Tlv Invalid Size            : 0

Packets Dropped Out Of Seq                  : 0

Packets Dropped Unknown Tlv                 : 0

Packets Dropped Tlv Invalid MC-Endpoint Id  : 0

Packets Dropped MD5                         : 0

Packets Dropped Unknown Peer                : 0

Packets Dropped MC Endpoint No Peer         : 0

Packets Tx                                  : 26099

Packets Tx Keepalive                        : 8221

Packets Tx Config                           : 2

Packets Tx Peer Config                      : 17872

Packets Tx State                            : 4

Packets Tx Failed                           : 0

===============================================================================

*A:Dut-B#

*A:Dut-B# show redundancy multi-chassis mc-endpoint peer 3.1.1.3 statistics

===============================================================================

Multi-Chassis MC-Endpoint Statistics

===============================================================================

Peer Addr                         : 3.1.1.3

-------------------------------------------------------------------------------

Packets Rx                        : 597

Packets Rx Keepalive              : 586

Packets Rx Config                 : 3

Packets Rx Peer Config            : 1

Packets Rx State                  : 7

Packets Dropped State Disabled    : 0

Packets Dropped Packets Too Short : 0

Packets Dropped Tlv Invalid Size  : 0

Packets Dropped Tlv Invalid LagId : 0

Packets Dropped Out of Seq        : 0

Packets Dropped Unknown Tlv       : 0

Packets Dropped MD5               : 0

Packets Tx                        : 636

Packets Tx Keepalive              : 600

Packets Tx Peer Config            : 30

Packets Tx Failed                 : 0

Packets Dropped No Peer           : 0

===============================================================================

*A:Dut-B#

*A:Dut-B# show redundancy multi-chassis mc-endpoint  endpoint 1 statistics

===============================================================================

Multi-Chassis Endpoint Statistics

===============================================================================

===============================================================================

MC-Endpoint Id 1

===============================================================================

Packets Rx Config                 : 3

Packets Rx State                  : 7

Packets Tx Config                 : 2

Packets Tx State                  : 4

Packets Tx Failed                 : 0

===============================================================================

Number of Entries 1

===============================================================================

mc-lag

Syntax

mc-lag [lag lag-id]

Context

This command displays multi-chassis LAG information.

Description

Parameters

lag lag-id

Shows information for the specified LAG identifier.

Values

1 — 800

mc-mobile

Syntax

mc-mobile peer {ip-address | ip6-address}

Context

This command displays multi-chassis LAG information.

Description

Parameters

Shows information for the specified IPv4 peer.

ipv6-address

Shows information for the specified IPv6 peer.

*A:Dut-A# show redundancy multi-chassis mc-mobile peer 10.90.1.2

===============================================================================

Multi-chassis Peer Mc-Mobile Table

===============================================================================

Peer                 : 10.90.1.2

Last State Change    : 12/04/2012 23:23:43

Admin State          : Up/Down               Oper State      : Up/Down/ISSU

Peer Version         : 5.0Rx

Keep Alive           : 10 deci-sec      Hold On Nbr Fail     : 3

BFD Svc ID           : 0                BFD Interface Name   : mc_intloopback

-------------------------------------------------------------------------------

Gateway Id           : 2

-------------------------------------------------------------------------------

Admin Role           : Primary          Oper Role            : Master

Peer Admin Role      : Secondary        Peer Oper Role       : Slave

Admin State          : Up               Oper State           : Up

Last Time Peer Connected : 12/04/2012 23:23:43

Last State Change    : 12/04/2012 23:23:43

Last State Chg Reason: Traffic Evnt

Geo-Redundancy State : Hot

CPM                  : 0                Geo Redundancy       : Hot

MSCP Group           : 1                Geo Redundancy       : Hot

===============================================================================

*A:Dut-A#

show>redundancy>multi-chassis>mc-lag

Syntax

peer ip-address [lag lag-id]

Context

Description

This command enables the context to display mc-lag peer-related redundancy information.

Parameters

Shows peer information about the specified IP address.

lag lag-id

Shows information for the specified LAG identifier.

Values

1 — 800

Output

Show Redundancy Multi-chassis MC-Lag Peer Output

The following table describes show redundancy multi-chassis mc-lag peer output fields:


Label	Description
Last Changed	Displays date and time of the last mc-lag peer.
Admin State	Displays the administrative state of the mc-lag peer.
Oper State	Displays the operation state of the mc-lag peer.
KeepAlive	Displays the length of time to keep alive the mg-lag peer.
Hold On Ngbr Failure	Specifies how many “keepalive” intervals the standby SR will wait for packets from the active node before assuming a redundant-neighbor node failure.

A:subscr_mgt# show redundancy multi-chassis mc-lag peer 10.10.10.30

===============================================================================

Multi-Chassis MC-Lag Peer 10.10.10.30

===============================================================================

Last Changed    : 01/23/2007 18:20:13

Admin State     : Up                  Oper State           : Up

KeepAlive       : 10 deci-seconds     Hold On Ngbr Failure : 3

-------------------------------------------------------------------------------

Lag Id Lacp Key Remote Lag Id System Id          Sys Prio Last Changed

-------------------------------------------------------------------------------

1      1        1             00:00:00:00:00:01  1        01/23/2007 18:20:13

2      2        2             00:00:00:00:00:02  2        01/24/2007 08:53:48

-------------------------------------------------------------------------------

Number of LAGs : 2

===============================================================================

A:subscr_mgt#

A:subscr_mgt# show redundancy multi-chassis mc-lag peer 10.10.10.30 lag 1

===============================================================================

Multi-Chassis MC-Lag Peer 10.10.10.30

===============================================================================

Last Changed    : 01/23/2007 18:20:13

Admin State     : Up                  Oper State           : Up

KeepAlive       : 10 deci-seconds     Hold On Ngbr Failure : 3

-------------------------------------------------------------------------------

Lag Id Lacp Key Remote Lag Id System Id          Sys Prio Last Changed

-------------------------------------------------------------------------------

1      1        1             00:00:00:00:00:01  1        01/23/2007 18:20:13

-------------------------------------------------------------------------------

Number of LAGs : 1

===============================================================================

A:subscr_mgt#

show>redundancy>multi-chassis>mc-lag

Syntax

statistics mc-lag [peer ip-address [lag lag-id]]

Context

Description

This command displays multi-chassis statistics.

Parameters

mc-lag

Displays multi-chassis LAG statistics.

peer ip-address

Shows the specified address of the multi-chassis peer.

lag lag-id

Shows information for the specified LAG identifier.

Values

1 — 800

Output

Show Redundancy Multi-chassis MC-Lag Peer Statistics Output

The following table describes show redundancy multi-chassis mc-lag peer output fields:


Label	Description
Packets Rx	Indicates the number of MC-Lag packets received from the peer.
Packets Rx Keepalive	Indicates the number of MC-Lag keepalive packets received from the peer.
Packets Rx Config	Indicates the number of received MC-Lag configured packets from the peer.
Packets Rx Peer Config	Indicates the number of received MC-Lag packets configured by the peer.
Packets Rx State	Indicates the number of MC-Lag “lag” state packets received from the peer.
Packets Dropped State Disabled	Indicates the number of packets that were dropped because the peer was administratively disabled.
Packets Dropped Packets Too Short	Indicates the number of packets that were dropped because the packet was too short.
Packets Dropped Tlv Invalid Size	Indicates the number of packets that were dropped because the packet size was invalid.
Packets Dropped Tlv Invalid LagId	Indicates the number of packets that were dropped because the packet referred to an invalid or non multi-chassis lag.
Packets Dropped Out of Seq	Indicates the number of packets that were dropped because the packet size was out of sequence.
Packets Dropped Unknown Tlv	Indicates the number of packets that were dropped because the packet contained an unknown TLV.
Packets Dropped MD5	Indicates the number of packets that were dropped because the packet failed MD5 authentication.
Packets Tx	Indicates the number of packets transmitted from this system to the peer.
Packets Tx Keepalive	Indicates the number of keepalive packets transmitted from this system to the peer.
Packets Tx Peer Config	Indicates the number of configured packets transmitted from this system to the peer.
Packets Tx Failed	Indicates the number of packets that failed to be transmitted from this system to the peer.

A:subscr_mgt# show redundancy multi-chassis mc-lag statistics

===============================================================================

Multi-Chassis Statistics

===============================================================================

Packets Rx                        : 52535

Packets Rx Keepalive              : 52518

Packets Rx Config                 : 2

Packets Rx Peer Config            : 4

Packets Rx State                  : 6

Packets Dropped KeepaliveTask     : 0

Packets Dropped Packet Too Short  : 0

Packets Dropped Verify Failed     : 0

Packets Dropped Tlv Invalid Size  : 0

Packets Dropped Out of Seq        : 0

Packets Dropped Unknown Tlv       : 0

Packets Dropped Tlv Invalid LagId : 0

Packets Dropped MD5               : 0

Packets Dropped Unknown Peer      : 0

Packets Tx                        : 52583

Packets Tx Keepalive              : 52519

Packets Tx Config                 : 2

Packets Tx Peer Config            : 54

Packets Tx State                  : 8

Packets Tx Failed                 : 0

===============================================================================

A:subscr_mgt#

B:Dut-B# show redundancy multi-chassis mc-lag peer 10.10.10.2 statistics

===============================================================================

Multi-Chassis Statistics, Peer 10.10.10.2

===============================================================================

Packets Rx                        : 231

Packets Rx Keepalive              : 216

Packets Rx Config                 : 1

Packets Rx Peer Config            : 2

Packets Rx State                  : 12

Packets Dropped State Disabled    : 0

Packets Dropped Packets Too Short : 0

Packets Dropped Tlv Invalid Size  : 0

Packets Dropped Tlv Invalid LagId : 0

Packets Dropped Out of Seq        : 0

Packets Dropped Unknown Tlv       : 0

Packets Dropped MD5               : 0

Packets Tx                        : 235

Packets Tx Keepalive              : 216

Packets Tx Peer Config            : 3

Packets Tx Failed                 : 0

===============================================================================

B:Dut-B#

mc-ring global-statistics

Syntax

mc-ring peer ip-address statistics

mc-ring peer ip-address [ring sync-tag [detail|statistics] ]

mc-ring peer ip-address ring sync-tag ring-node [ring-node-name [detail|statistics] ]

Context

This command displays multi-chassis ring information.

Description

Parameters

Specifies the address of the multi-chassis peer to display.

ring sync-tag

Specifies a synchronization tag to be displayed that was used while synchronizing this port with the multi-chassis peer.

node ring-node-name

Specifies a ring-node name.

global-statistics

Displays global statistics for the multi-chassis ring.

Displays detailed peer information for the multi-chassis ring.

Output

Show mc-ring peer ip-address ring Output

The following table describes mc-ring peer ip-address ring output fields.


Label	Description
Sync Tag	Displays the synchronization tag that was used while synchronizing this port with the multi-chassis peer.
Oper State	noPeer The peer has no corresponding ring configured.
	connected The in-band control connection with the peer is operational.
	broken The in-band control connection with the peer has timed out.
	conflict The in-band control connection with the peer has timed out but the physical connection is still OK; the failure of the in-band signaling connection is caused by a misconfiguration. For example, a conflict between the configuration of this system and its peer, or a misconfiguration on one of the ring access node systems.
	testingRing The in-band control connection with the peer is being set up. Waiting for result.
	waitingForPeer Verifying if this ring is configured on the peer.
	configErr The ring is administratively up, but a configuration error prevents it from operating properly.
	halfBroken The in-band control connection indicates that the ring is broken in one direction (towards the peer).
	localBroken The in-band control connection with the peer is known to be broken due to local failure or local administrative action.
	shutdown The ring is shutdown.
Failure Reason	Displays the reason of the failure of the operational state of a MC ring.
No. of MC Ring entries	Displays the number of MC ring entries.

Show Redundancy Multi-Chassis Ring Peer Statistics Output

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2 ring ring11 detail

==============================================================================

Multi-Chassis MC-Ring Detailed Information

==============================================================================

Peer           : 10.0.0.2

Sync Tag       : ring11

Port ID        : 1/1/3

Admin State    : inService

Oper State     : connected

Admin Change   : 01/07/2008 21:40:07

Oper Change    : 01/07/2008 21:40:24

Failure Reason : None

------------------------------------------------------------------------------

In Band Control Path

------------------------------------------------------------------------------

Service ID     : 10

Interface Name : to_an1

Oper State     : connected

Dest IP        : 10.10.0.2

Src  IP        : 10.10.0.1

------------------------------------------------------------------------------

VLAN Map B Path Provisioned

------------------------------------------------------------------------------

range 13-13

range 17-17

------------------------------------------------------------------------------

VLAN Map Excluded Path Provisioned

------------------------------------------------------------------------------

range 18-18

------------------------------------------------------------------------------

VLAN Map B Path Operational

------------------------------------------------------------------------------

range 13-13

range 17-17

------------------------------------------------------------------------------

VLAN Map Excluded Path Operational

------------------------------------------------------------------------------

range 18-18

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 192.251.10.104

==============================================================================

MC Ring entries

==============================================================================

Sync Tag                         Oper State      Failure Reason

------------------------------------------------------------------------------

No. of MC Ring entries: 0

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2

==============================================================================

MC Ring entries

==============================================================================

Sync Tag                         Oper State      Failure Reason

------------------------------------------------------------------------------

ring11                           connected       None

ring12                           shutdown        None

------------------------------------------------------------------------------

No. of MC Ring entries: 4

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2 ring ring11 ring-node an1 detail

==============================================================================

Multi-Chassis MC-Ring Node Detailed Information

==============================================================================

Peer           : 10.0.0.2

Sync Tag       : ring11

Node Name      : an1

Oper State Loc : connected

Oper State Rem : notTested

In Use         : True

Admin Change   : 01/07/2008 21:40:07

Oper Change    : 01/07/2008 21:40:25

Failure Reason : None

------------------------------------------------------------------------------

Ring Node Connectivity Verification

------------------------------------------------------------------------------

Admin State    : inService

Service ID     : 11

VLAN Tag       : 11

Dest IP        : 10.11.3.1

Src  IP        : None

Interval       : 1 minutes

Src MAC        : None

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 10.0.0.2 ring ring11 ring-node

==============================================================================

MC Ring Node entries

==============================================================================

Name                             Loc Oper St.      Failure Reason

  In Use                           Rem Oper St.

------------------------------------------------------------------------------

an1                              connected         None

  Yes                              notTested

an2                              connected         None

  Yes                              notTested

------------------------------------------------------------------------------

No. of MC Ring Node entries: 2

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#

The following table describes multi-chassis ring peer output fields.


Label	Description
Message	Displays the message type.
Received	Indicates the number of valid MC-ring signalling messages received from the peer.
Transmitted	Indicates the number of valid MC-ring signalling messages transmitted from the peer.
MCS ID Request	Displays the number of valid MCS ID requests were received from the peer.
MCS ID Response	Displays the number of valid MCS ID responses were received from the peer.
Ring Exists Request	Displays the number of valid 'ring exists' requests were received from the peer.
Ring Exists Response	Displays the number of valid ring exists' responses were received from the peer.
Keepalive	Displays the number of valid MC-ring control packets of type 'keepalive' were received from the peer.

Show mc-ring ring-node Command Output

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 192.251.10.104 statistics

==============================================================================

MC Ring statistics for peer 192.251.10.104

==============================================================================

Message                                              Received     Transmitted

------------------------------------------------------------------------------

MCS ID Request                                       0            0

MCS ID Response                                      0            0

Ring Exists Request                                  0            0

Ring Exists Response                                 0            0

Keepalive                                            0            0

------------------------------------------------------------------------------

Total                                                0            0

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#


Label	Description
Oper State	Displays the state of the connection verification (both local and remote).
	notProvisioned Connection verification is not provisioned.
	configErr Connection verification is provisioned but a configuration error prevents it from operating properly.
	notTested Connection verification is administratively disabled or is not possible in the current situation.
	testing Connection Verification is active, but no results are yet available.
	connected The ring node is reachable.
	disconnected Connection verification has timed out.
In Use	Displays “True” if the ring node is referenced on an e-pipe or as an inter-dest-id on a static host or dynamic lease.

Show mc-ring global-statistics Command Output


Label	Description
Rx	Displays the number of MC-ring signalling packets were received by this system.
Rx Too Short	Displays the number of MC-ring signalling packets were received by this system that were too short.
Rx Wrong Authentication	Displays the number of MC-ring signalling packets were received by this system with invalid authentication.
Rx Invalid TLV	Displays the number of MC-ring signalling packets were received by this system with invalid TLV.
Rx Incomplete	Displays the number of MC-ring signalling packets were received by this system that were incomplete.
Rx Unknown Type	Displays the number of MC-ring signalling packets were received by this system that were of unknown type.
Rx Unknown Peer	Displays the number of MC-ring signalling packets were received by this system that were related to an unknown peer.
Rx Unknown Ring	Displays the number of MC-ring signalling packets were received by this system that were related to an unknown ring.
Rx Unknown Ring Node	Displays the number of MC-ring signalling packets were received by this system that were related to an unknown ring node.
Tx	Displays the number of MC-ring signalling packets were transmitted by this system.
Tx No Buffer	Displays the number of MC-ring signalling packets could not be transmitted by this system due to a lack of packet buffers.
Tx Transmission Failed	Displays the number of MC-ring signalling packets could not be transmitted by this system due to a transmission failure.
Tx Unknown Destination	Displays the number of MC-ring 'unknown destination' signalling packets were transmitted by this system.
Missed Configuration Events	Displays the number of missed configuration events on this system.
Missed BFD Events	Displays the number of missed BFD events on this system.

*A:ALA-48>show>redundancy>multi-chassis# mc-ring global-statistics

==============================================================================

Global MC Ring statistics

==============================================================================

Rx                           : 0

Rx Too Short                 : 0

Rx Wrong Authentication      : 0

Rx Invalid TLV               : 0

Rx Incomplete                : 0

Rx Unknown Type              : 0

Rx Unknown Peer              : 0

Rx Unknown Ring              : 0

Rx Unknown Ring Node         : 0

Tx                           : 36763

Tx No Buffer                 : 0

Tx Transmission Failed       : 0

Tx Unknown Destination       : 0

Missed Configuration Events  : 0

Missed BFD Events            : 0

==============================================================================

*A:ALA-48>show>redundancy>multi-chassis#

sync

Syntax

sync [port port-id | lag-id]

Context

This command displays synchronization information.

Description

Parameters

port port-id

Shows the specified port ID of the multi-chassis peer.

lag lag-id

Shows information for the specified LAG identifier.

Values

1 — 800

Output

Show Redundancy Multi-chassis Sync Output

The following table describes show redundancy multi-chassis sync output fields:


Label	Description
Peer IP Address	Displays the multi-chassis redundancy peer.
Description	The text string describing the peer.
Authentication	If configured, displays the authentication key used between this node and the multi-chassis peer.
Source IP Address	Displays the source address used to communicate with the multi-chassis peer.
Admin State	Displays the administrative state of the peer.
Client Applications	Displays the list of client applications synchronized between SRs.
Sync Admin State	Displays the administrative state of the synchronization.
Sync Oper State	Displays the operation state of the synchronization.
DB Sync State	Displays the database state of the synchronization.
Num Entries	Displays the number of entries on local router.
Lcl Deleted Entries	Displays the number of deleted entries made at the local router.
Alarm Entries	Displays the alarm entries on the local router.
Rem Num Entries	Displays the number of entries on the remote router.
Rem Lcl Deleted Entries	Displays the number of locally deleting entries made by the remote router.
Rem Alarm Entries	Displays alarm entries on the remote router.

*A:subscr_mgt_2# show redundancy multi-chassis sync

===============================================================================

Multi-chassis Peer Table

===============================================================================

Peer

-------------------------------------------------------------------------------

Peer IP Address         : 10.10.10.20

Description             : Mc-Lag peer 10.10.10.20

Authentication          : Disabled

Source IP Address       : 0.0.0.0

Admin State             : Enabled

-------------------------------------------------------------------------------

Sync-status

-------------------------------------------------------------------------------

Client Applications     : SUBMGMT

Sync Admin State        : Up

Sync Oper State         : Up

DB Sync State           : inSync

Num Entries             : 1

Lcl Deleted Entries     : 0

Alarm Entries           : 0

Rem Num Entries         : 1

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

===============================================================================

A:subscr_mgt_2#

show>redundancy>multi-chassis>sync

Syntax

peer ip-address

Context

Description

This command enables the context to display peer-related redundancy information.

Parameters

Shows peer information about the specified IP address.

Output

Show Redundancy Multi-chassis Sync Peer Output

The following table describes show redundancy multi-chassis sync output fields:


Label	Description
Peer IP Address	Displays the multi-chassis redundancy peer.
Description	The text string describing the peer.
Authentication	If configured, displays the authentication key used between this node and the multi-chassis peer.
Source IP Address	Displays the source address used to communicate with the multi-chassis peer.
Admin State	Displays the administrative state of the peer.
Client Applications	Displays the list of client applications synchronized between SRs.
Sync Admin State	Displays the administrative state of the synchronization.
Sync Oper State	Displays the operation state of the synchronization.
DB Sync State	Displays the database state of the synchronization.
Num Entries	Displays the number of entries on local router.
Lcl Deleted Entries	Displays the number of deleted entries made at the local router.
Alarm Entries	Displays the alarm entries on the local router.
Rem Num Entries	Displays the number of entries on the remote router.
Rem Lcl Deleted Entries	Displays the number of locally deleting entries made by the remote router.
Rem Alarm Entries	Displays alarm entries on the remote router.

*A:subscr_mgt_2# show redundancy multi-chassis sync peer 10.10.10.20

===============================================================================

Multi-chassis Peer Table

===============================================================================

Peer

-------------------------------------------------------------------------------

Peer IP Address         : 10.10.10.20

Description             : Mc-Lag peer 10.10.10.20

Authentication          : Disabled

Source IP Address       : 0.0.0.0

Admin State             : Enabled

-------------------------------------------------------------------------------

Sync-status

-------------------------------------------------------------------------------

Client Applications     : SUBMGMT

Sync Admin State        : Up

Sync Oper State         : Up

DB Sync State           : inSync

Num Entries             : 1

Lcl Deleted Entries     : 0

Alarm Entries           : 0

Rem Num Entries         : 1

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

===============================================================================

MCS Application Stats

===============================================================================

Application             : igmp

Num Entries             : 0

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 0

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

-------------------------------------------------------------------------------

Application             : igmpSnooping

Num Entries             : 0

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 0

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

-------------------------------------------------------------------------------

Application             : subMgmt

Num Entries             : 1

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 1

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

-------------------------------------------------------------------------------

Application             : srrp

Num Entries             : 0

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 0

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

===============================================================================

*A:subscr_mgt_2#

Syntax

show>redundancy>multi-chassis>peer

Context

Description

This command displays detailed peer information.

Output

Show Redundancy Multi-chassis Sync Peer Detail Output

The following table describes show redundancy multi-chassis sync detail output fields:


Label	Description
Peer IP Address	Displays the multi-chassis redundancy peer.
Description	The text string describing the peer.
Authentication	If configured, displays the authentication key used between this node and the multi-chassis peer.
Source IP Address	Displays the source address used to communicate with the multi-chassis peer.
Admin State	Displays the administrative state of the peer.
Client Applications	Displays the list of client applications synchronized between routers.
Sync Admin State	Displays the administrative state of the synchronization.
Sync Oper State	Displays the operation state of the synchronization.
DB Sync State	Displays the database state of the synchronization.
Num Entries	Displays the number of entries on local router.
Lcl Deleted Entries	Displays the number of deleted entries made at the local router.
Alarm Entries	Displays the alarm entries on the local router.
Rem Num Entries	Displays the number of entries on the remote router.
Rem Lcl Deleted Entries	Displays the number of locally deleting entries made by the remote router.
Rem Alarm Entries	Displays alarm entries on the remote router.

*A:subscr_mgt_2# show redundancy multi-chassis sync peer 10.10.10.20 detail

===============================================================================

Multi-chassis Peer Table

===============================================================================

Peer

-------------------------------------------------------------------------------

Peer IP Address         : 10.10.10.20

Description             : Mc-Lag peer 10.10.10.20

Authentication          : Disabled

Source IP Address       : 0.0.0.0

Admin State             : Enabled

-------------------------------------------------------------------------------

Sync-status

-------------------------------------------------------------------------------

Client Applications     : SUBMGMT

Sync Admin State        : Up

Sync Oper State         : Up

DB Sync State           : inSync

Num Entries             : 1

Lcl Deleted Entries     : 0

Alarm Entries           : 0

Rem Num Entries         : 1

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

===============================================================================

MCS Application Stats

===============================================================================

Application             : igmp

Num Entries             : 0

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 0

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

-------------------------------------------------------------------------------

Application             : igmpSnooping

Num Entries             : 0

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 0

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

-------------------------------------------------------------------------------

Application             : subMgmt

Num Entries             : 1

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 1

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

-------------------------------------------------------------------------------

Application             : srrp

Num Entries             : 0

Lcl Deleted Entries     : 0

Alarm Entries           : 0

-------------------------------------------------------------------------------

Rem Num Entries         : 0

Rem Lcl Deleted Entries : 0

Rem Alarm Entries       : 0

===============================================================================

Ports synced on peer 10.10.10.20

===============================================================================

Port/Encap                    Tag

-------------------------------------------------------------------------------

lag-1                         test123

===============================================================================

*A:subscr_mgt_2#

Syntax

This command displays redundancy synchronization times.

Context

show>redundancy

Description

This command displays information on the configured time ranges.

A:ALA-48>show>redundancy# synchronization

===============================================================================

Synchronization Information

===============================================================================

Standby Status               : disabled

Last Standby Failure         : N/A

Standby Up Time              : N/A

Failover Time                : N/A

Failover Reason              : N/A

Boot/Config Sync Mode        : None

Boot/Config Sync Status      : No synchronization

Last Config File Sync Time   : Never

Last Boot Env Sync Time      : Never

===============================================================================

A:ALA-48>show>redundancy#

time-range

Syntax

time-range name associations [detail]

Context

show>cron

Description

Output

Time Range Output

The following table displays system time range output fields:


Label	Description
Associations	Shows the time-range as it is associated with the TOD suites and ACL entries as well as the SAPs using them.
Detail	Shows the details of this time-range.

The following example shows time-range detail output.

A:ala# show cron time-range time-range2 detail

===============================================================================

Cron time-range

===============================================================================

Name 	    : time-range1

Periodic	    : Start * * * * End * * * *

Absolute 	    : Start * * * * End * * * *

The following example shows output for time-range associations with previously created IP and MAC filters.

A:ala# show cron time-range day associations

===============================================================================

Cron time-range associations

===============================================================================

Name          : day                            State  : Inactive

-------------------------------------------------------------------------------

IP Filter associations

-------------------------------------------------------------------------------

IP filter Id  : 10, entry 1010

-------------------------------------------------------------------------------

MAC Filter associations

-------------------------------------------------------------------------------

None

-------------------------------------------------------------------------------

Tod-suite associations

-------------------------------------------------------------------------------

Tod-suite : suite_sixteen, for Ingress Qos Policy "1160"

Tod-suite : suite_sixteen, for Ingress Scheduler Policy "SchedPolCust1_Day"

Tod-suite : suite_sixteen, for Egress Qos Policy "1160"

Tod-suite : suite_sixteen, for Egress Scheduler Policy "SchedPolCust1Egress_Day

===============================================================================

script-control

Syntax

script-control

Context

This command enables the context to display script information.

Description

script

Syntax

script [script-name] [owner script-owner]

Context

show>system>script-control

Description

This command displays script parameters.

Parameters

script-name

Displays information for the specified script.

owner script-owner

Displays information for the specified script owner.

Output

The following table describes the show script output fields.


Label	Description
Script	Displays the name of the script.
Script owner	Displays the owner name of script.
Administrative status	Enabled Administrative status is enabled.
	Disabled Administratively disabled.
Operational status	Enabled Operational status is enabled.
	Disabled Operationally disabled.
Script source location	Displays the location of scheduled script.
Last script error	Displays the system time of the last error.
Last change	Displays the system time of the last change.

show>system>script-control

A:sim1>show>system>script-control# script

===============================================================================

Script Information

===============================================================================

Script                       : test

Owner name                   : TiMOS CLI

Description                  : asd

Administrative status        : enabled

Operational status           : enabled

Script source location       : ftp://*****:******@100.100.100.1/home/testlab_bgp

                               /test1.cfg

Last script error            : none

Last change                  : 2015/01/07 17:10:03

===============================================================================

A:sim1>show>cron#

script-policy

Syntax

script-policy script-policy-name [owner owner-name]

script-policy run-history [run-state]

Context

Description

This command displays script policy information.

Parameters

script-policy-name

Displays policy information for the specified script.

owner owner-name

Displays information for the specified script owner.

Default

“TiMOS CLI”

run-state

Displays information for script policies in the specified state.

Values

executing | initializing | terminated

Output

Script Policy Output

The following table describes script policy output fields.


Label	Description
Script policy	Displays the name of the script policy.
Script policy owner	The name of the script policy owner.
Administrative status	Enabled — Administrative status is enabled. Disabled — Administrative status is disabled.
Script	The name of the script.
Script owner	The name of the script owner.
Script source location	Displays the location of scheduled script.
Max running allowed	Displays the maximum number of allowed sessions.
Max completed run histories	Displays the maximum number of sessions previously run.
Max lifetime allowed	Displays the maximum amount of time the script may run.
Completed run histories	Displays the number of completed sessions.
Executing run histories	Displays the number of sessions in the process of executing.
Initializing run histories	Displays the number of sessions ready to run/queued but not executed.
Max time tun history saved	Displays the maximum amount of time to keep the results from a script run.
Last change	Displays the system time a change was made to the configuration.

This command displays the time since the system started.

*A:Redundancy# show system script-control script-policy run-history terminated

===============================================================================

Script-policy Run History

===============================================================================

Script policy "test"

Owner "TiMOS CLI"

-------------------------------------------------------------------------------

Script Run #17

-------------------------------------------------------------------------------

Start time : 2006/11/06 20:30:09 End time : 2006/11/06 20:35:24

Elapsed time : 0d 00:05:15 Lifetime : 0d 00:00:00

State : terminated Run exit code : noError

Result time : 2006/11/06 20:35:24 Keep history : 0d 00:49:57

Error time : never

Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203008.

out

Run exit : Success

-------------------------------------------------------------------------------

Script Run #18

-------------------------------------------------------------------------------

Start time : 2006/11/06 20:35:24 End time : 2006/11/06 20:40:40

Elapsed time : 0d 00:05:16 Lifetime : 0d 00:00:00

State : terminated Run exit code : noError

Result time : 2006/11/06 20:40:40 Keep history : 0d 00:55:13

Error time : never

Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203523.

out

Run exit : Success

-------------------------------------------------------------------------------

*A:Redundancy#

*A:Redundancy# show system script-control script-policy run-history executing

===============================================================================

Script-policy Run History

===============================================================================

Script policy "test"

Owner "TiMOS CLI"

-------------------------------------------------------------------------------

Script Run #20

-------------------------------------------------------------------------------

Start time : 2006/11/06 20:46:00 End time : never

Elapsed time : 0d 00:00:56 Lifetime : 0d 00:59:04

State : executing Run exit code : noError

Result time : never Keep history : 0d 01:00:00

Error time : never

Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-204559.

out

===============================================================================

*A:Redundancy#

*A:Redundancy# show system script-control script-policy run-history initializing

===============================================================================

Script-policy Run History

===============================================================================

Script policy "test"

Owner "TiMOS CLI"

-------------------------------------------------------------------------------

Script Run #21

-------------------------------------------------------------------------------

Start time : never End time : never

Elapsed time : 0d 00:00:00 Lifetime : 0d 01:00:00

State : initializing Run exit code : noError

Result time : never Keep history : 0d 01:00:00

Error time : never

Results file : none

-------------------------------------------------------------------------------

Script Run #22

-------------------------------------------------------------------------------

Start time : never End time : never

Elapsed time : 0d 00:00:00 Lifetime : 0d 01:00:00

State : initializing Run exit code : noError

Result time : never Keep history : 0d 01:00:00

Error time : never

Results file : none

-------------------------------------------------------------------------------

Script Run #23

-------------------------------------------------------------------------------

Start time : never End time : never

Elapsed time : 0d 00:00:00 Lifetime : 0d 01:00:00

State : initializing Run exit code : noError

Result time : never Keep history : 0d 01:00:00

Error time : never

Results file : none

===============================================================================

*A:Redundancy#

uptime

Syntax

uptime

Context

show

Description

Output

Uptime Output

The following table describes uptime output fields.


Label	Description
System Up Time	Displays the length of time the system has been up in days, hr:min:sec format.

A:ALA-1# show uptime

System Up Time         : 11 days, 18:32:02.22 (hr:min:sec)

A:ALA-1#

switch-fabric

Syntax

switch-fabric

Context

This command displays switch fabric information.

Description

Output

Switch fabric output

The following table describes switch-fabric output fields for 12-slot and 7-slot chassis models:.


Label	Description
Slot/MDA	Displays the fabric slot within a chassis in the system. The CPM cards and IOM cards cannot be physically inserted into the switch fabric card slots.
Min. Forwarding Capacity	Displays the minimum forwarding capacity of the slot and MDA as a percentage.
Max. Forwarding Capacity	Displays the maximum forwarding capacity of the slot and MDA as a percentage.

A:ALA-7# show system switch-fabric

==============================================================================
Switch Fabric
==============================================================================
Slot/Mda 	Min. Forwarding Capacity 	Max. Forwarding Capacity
------------------------------------------------------------------------------
1/1 	100% 		100%
1/2 	100% 		100%
2/1 	100% 		100%
2/2 	100% 		100%
3/1 	100% 		100%
3/2 	100% 		100%
4/1 	100% 		100%
4/2 	100% 		100%
5/1 	100% 		100%
5/2 	100% 		100%
A 	100% 		100%
B 	100% 		100%
==============================================================================
A:ALA-7#

A:ALA-12# show system switch-fabric

==============================================================================
Switch Fabric
==============================================================================
Slot/Mda 	Min. Forwarding Capacity 	Max. Forwarding Capacity
------------------------------------------------------------------------------
1/1 	100% 		100%
1/2 	100% 		100%
2/1 	100% 		100%
2/2 	100% 		100%
3/1 	100% 		100%
3/2 	100% 		100%
4/1 	100% 		100%
4/2 	100% 		100%
5/1 	100% 		100%
5/2 	100% 		100%
6/1 	100% 		100%
6/2 	100% 		100%
7/1 	100% 		100%
7/2 	100% 		100%
8/1 	100% 		100%
8/2 	100% 		100%
A 	100% 		100%
B 	100% 		100%
==============================================================================
A:ALA-12

sync-if-timing

Syntax

sync-if-timing

Context

This command displays synchronous interface timing operational information.

Description

Output

System Timing Output

The following table describes sync-if-timing output fields.

Label

Description

System Status CPM A/B

Indicates the present status of the synchronous timing equipment subsystem (SETS).

Not Present — Only shown on systems without central clocks (7450 ESS-1)

Master Freerun — The clock is in free-run because it hasn’t had a qualified input reference to lock to

Master Holdover — The clock was locked to an input reference but has lost all qualified input references and is in holdover.

Master Locked — The clock is locked to an input reference

Acquiring — The clock is training to a qualified input reference.

Reference Input Mode

Revertive

Indicates that for a re-validated or a newly validated reference source which has a higher priority than the currently selected reference has reverted to the new reference source.

Non-revertive

The clock cannot revert to a higher priority clock if the current clock goes offline.

Quality Level Selection

Indicates whether the ql-selection command has been enabled or disabled. If this command is enabled, then the reference is selected first using the QL value, then by the priority reference order. If this command is not enabled, then the reference is selected by the priority reference order.

Reference Selected

Indicates which reference has been selected:

•

ref1, ref2 - (for all chassis)

•

BITS A, BITS B - (7750 SR-7/12)

•

Mate CPM (BITS A), Mate CPM (BITS B) - (7750 SR-7/12 on the active CPM)

•

Mate CPM (none) - show>system>sync-if-timing> standby when standby locked to active which is freerun or holdover - (7750 SR-7/12)

•

Mate CPM (ref1), Mate CPM (ref2) - show>system>sync-if-timing>standby when standby locked to active which is locked to ref1 or ref2 - (7750 SR-7/12)

•

BITS 1, BITS2 - (7750 SR-c4 only)

System Quality Level

Indicates the quality level being generated by the system clock.

Current Frequency Offset

(value)

The frequency offset of the currently selected timing reference in parts per million.

Reference Order

ref1, ref2, bits

Indicates that the priority order of the timing references.

Reference Mate CPM

Data within this block represents the status of the timing reference provided by the Mate CPM. This will be the BITS input from the standby CPM.

Admin Status

down

The ref1 or ref2 configuration is administratively shutdown.

The ref1 or ref2 configuration is administratively enabled.

diag

Indicates the reference has been forced using the force-reference command.

Quality Level Override

Indicates whether the QL value used to determine the reference was configured directly by the user.

Rx Quality Level

Indicates the QL value received on the interface.

•

inv - SSM received on the interface indicates an invalid code for the interface type.

•

unknown - No QL value was received on the interface.

Qualified for Use

Indicates whether the reference has been qualified to be used as a source of timing for the node.

Not Qualified Due To

Indicates the reason why the reference has not been qualified:

Indicates whether the method is presently selected.

Not Selected Due To

Indicates the reason why the method is not selected:

Identifies the Source port for the reference.

Interface Type

The interface type configured for the BITS port.

Framing

The framing configured for the BITS port.

Line Coding

The line coding configured for the BITS port.

Line Length

The line length value of the BITS output.

Output Admin Status

down

The BITS output is administratively shutdown.

The BITS output is administratively enabled.

diag

Indicates the BITS output has been forced using the force-reference command.

Output Source

The source to be used to provide the signal on the BITS output port.

line reference

unfiltered recovered line reference.

internal clock

filtered node clock output.

Output Reference Selected

The reference selected as the source for the BITS output signal (ref1 or ref2).

TX Quality Level

QL value for BITS output signal.

The following example is for a node locked to the active BITS input and directing the signal on ref1 to the BITS output:

The following example is for a node locked to the standby CPM BITS input and directing the ref1 signal to the BITS output port:

*A:SR7# show system sync-if-timing

===============================================================================

System Interface Timing Operational Info

===============================================================================

System Status CPM A                : Master Locked

    Reference Input Mode           : Non-revertive

    Quality Level Selection        : Disabled

    Reference Selected             : BITS A

    System Quality Level           : prs

    Current Frequency Offset (ppm) : +0

Reference Order                    : bits ref1 ref2

Reference Mate CPM

    Qualified For Use              : Yes

    Selected For Use               : No

        Not Selected Due To        :     on standby

Reference Input 1

    Admin Status                   : up

    Rx Quality Level               : prs

    Qualified Level Override       : none

    Qualified For Use              : Yes

    Selected For Use               : No

        Not Selected Due To        :     on standby

    Source Port                    : 3/1/2

Reference Input 2

    Admin Status                   : down

    Rx Quality Level               : unknown

    Qualified Level Override       : none

    Qualified For Use              : No

        Not Qualified Due To       :     disabled

    Selected For Use               : No

        Not Selected Due To        :     disabled

    Source Port                    : None

Reference BITS A

    Admin Status                   : up

    Rx Quality Level               : prs

    Qualified Level Override       : none

    Qualified For Use              : Yes

    Selected For Use               : Yes

    Interface Type                 : DS1

    Framing                        : ESF

    Line Coding                    : B8ZS

    Line Length                    : 550-660ft

    Output Admin Status            : up

    Output Source                  : line reference

    Output Reference Selected      : ref1

    Tx Quality Level               : prs

===============================================================================

*A:SR7#

*A:Dut-B# show system sync-if-timing

=======================================================================

System Interface Timing Operational Info

=======================================================================

System Status CPM A                : Master Locked

    Reference Input Mode           : Non-revertive

    Quality Level Selection        : Disabled

    Reference Selected             : Mate CPM (BITS B)

    System Quality Level           : prs

    Current Frequency Offset (ppm) : +0

Reference Order                    : bits ref1 ref2

Reference Mate CPM

    Qualified For Use              : Yes

    Selected For Use               : Yes

Reference Input 1

    Admin Status                   : up

    Rx Quality Level               : prs

    Quality Level Override         : none

    Qualified For Use              : Yes

    Selected For Use               : No

        Not Selected Due To        : on standby

    Source Port                    : 3/1/2

Reference Input 2

    Admin Status                   : down

    Rx Quality Level               : unknown

    Quality Level Override         : none

    Qualified For Use              : No

        Not Qualified Due To       : disabled

    Selected For Use               : No

        Not Selected Due To        : disabled

    Source Port                    : None

Reference BITS A

    Admin Status                   : up

    Rx Quality Level               : unknown

    Quality Level Override         : none

    Qualified For Use              : No

        Not Qualified Due To       : LOS

    Selected For Use               : No

        Not Selected Due To        : not qualified

    Interface Type                 : DS1

    Framing                        : ESF

    Line Coding                    : B8ZS

    Line Length                    : 550-660ft

    Output Admin Status            : up

    Output Source                  : line reference

    Output Reference Selected      : ref1

    Tx Quality Level               : prs

======================================================================

The following example is for a node whose standby CPM is locked to its local BITS port and the signal from ref1 is directed to the BITS output port:

A:SR7# show system sync-if-timing standby

===============================================================================

System Interface Timing Operational Info

===============================================================================

System Status CPM B                : Master Locked

    Reference Input Mode           : Non-revertive

    Quality Level Selection        : Disabled

    Reference Selected             : BITS B

    System Quality Level           : prs

    Current Frequency Offset (ppm) : +0

Reference Order                    : bits ref1 ref2

Reference Mate CPM

    Qualified For Use              : Yes

    Selected For Use               : No

        Not Selected Due To        : on standby

Reference Input 1

    Admin Status                   : down

    Rx Quality Level               : unknown

    Quality Level Override         : none

    Qualified For Use              : No

        Not Qualified Due To       : disabled

    Selected For Use               : No

        Not Selected Due To        : disabled

    Source Port                    : None

Reference Input 2

    Rx Quality Level               : unknown

    Quality Level Override         : none

    Qualified For Use              : No

        Not Qualified Due To       : disabled

    Selected For Use               : No

        Not Selected Due To        : disabled

    Source Port                    : None

Reference BITS B

    Admin Status                   : up

    Rx Quality Level               : prs

    Quality Level Override         : none

    Qualified For Use              : Yes

    Selected For Use               : Yes

    Interface Type                 : DS1

    Framing                        : ESF

    Line Coding                    : B8ZS

    Line Length                    : 550-660ft

    Output Admin Status            : up

    Output Source                  : line reference

    Output Reference Selected      : ref1

    Tx Quality Level               : prs

===============================================================================

*A:SR7#

Syntax

show>redundancy>synchronization

Context

Description

This command displays redundancy synchronization times.

Output

Synchronization Output

The following table describes redundancy synchronization output fields.


Label	Description
Standby Status	Displays the status of the standby CPM.
Last Standby Failure	Displays the timestamp of the last standby failure.
Standby Up Time	Displays the length of time the standby CPM has been up.
Failover Time	Displays the timestamp when the last redundancy failover occurred causing a switchover from active to standby CPM. If there is no redundant CPM card in this system or no failover has occurred since the system last booted, the value will be 0.
Failover Reason	Displays a text string giving an explanation of the cause of the last redundancy failover. If no failover has occurred, an empty string displays.
Boot/Config Sync Mode	Displays the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the configuration files or the boot environment information contained in the boot options file (BOF).
Boot/Config Sync Status	Displays the results of the last synchronization operation between the primary and secondary CPMs.
Last Config File Sync Time	Displays the timestamp of the last successful synchronization of the configuration files.
Last Boot Env Sync Time	Displays the timestamp of the last successful synchronization of the boot environment files.

The context to debug synchronous interface timing references.

A:ALA-1>show>redundancy# synchronization

===============================================================================

Synchronization Information

===============================================================================

Standby Status               : disabled

Last Standby Failure         : N/A

Standby Up Time              : N/A

Failover Time                : N/A

Failover Reason              : N/A

Boot/Config Sync Mode        : None

Boot/Config Sync Status      : No synchronization

Last Config File Sync Time   : Never

Last Boot Env Sync Time      : Never

===============================================================================

A:ALA-1>show>redundancy#

Syntax

Context

Description

force-reference

Syntax

force-reference {ref1 | ref2 | bits | ptp}

no force-reference

Context

debug>sync-if-timing

Description

This command allows an operator to force the system synchronous timing output to use a specific reference.

Note: The debug sync-if-timing force-reference command should only be used to test and debug problems. Network synchronization problems may appear if network elements are left with this manual override setting. Once the system timing reference input has been forced, it may be cleared using the no force-reference command.

The CPM clock can be forced to use a specific input reference using the force-reference command.

When the command is executed, the CPM clock on the active CPM immediately switches its input reference to that specified by the command. If the specified input is not available (shutdown), or in a disqualified state, the CPM clock shall use the next qualified input reference based on the selection rules.

This command also affects the BITS output port on the active CPM. If the BITS output port selection is set to line-reference and the reference being forced is not the BITS input port, then the system uses the forced reference to generate the signal out the BITS output port. If the BITS output port selection is set to internal-clock, then the system uses the output of the CPM clock to generate the signal for the BITS output port.

On a CPM activity switch, the force command is cleared and normal reference selection is determined.

Debug configurations are not saved between reboots.

Note: The 7750 SR-c4 has two BITS input ports on the CFM. The force reference command on this system allows the selection of the specific port.

7750 SR-c4 CLI Syntax: debug>sync-if-timing>force-reference {ref1 | ref2 | bits1 | bits2}

Parameters

ref1

The clock will use the first timing reference.

ref2

The clock will use the second timing reference.

bits

The clock will use the external network interface on the active CPM to be the highest priority input.

bits1

(7750 SR-c4) The clock will use the bits1 timing reference.

bits2

(7750 SR-c4) The clock will use the bits2 timing reference.

ptp

The clock will use the PTP slave as the timing reference.

system

Syntax

[no] system

Context

debug

Description

This command displays system debug information.

http-connections

Syntax

http-connections [host-ip-address/mask]

http-connections

Context

debug>system

Description

This command displays HTTP connections debug information.

Parameters

host-ip-address/mask

Displays information for the specified host IP address and mask.

ntp

Syntax

[no] router router-name interface ip-int-name

Context

debug>system

Description

This command enables and configures debugging for NTP.

The no form of the command disables debugging for NTP.

Parameters

Default

maximum 32 characters; must begin with a letter. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.

persistence

Syntax

[no] persistence

Context

debug>system

Description

This command displays persistence debug information.

Syntax

Context

Description

This command enables the context to dump redundancy parameters.

Syntax

This command enables the context to dump multi-chassis parameters.

Context

tools>dump>redundancy

Description

mc-endpoint

Syntax

mc-endpoint peer ip-address

Context

This command dumps multi-chassis endpoint information.

Description

Parameters

peer ip-address

*A:Dut-B# tools dump redundancy multi-chassis mc-endpoint peer 3.1.1.3

MC Endpoint Peer Info

    peer addr                    : 3.1.1.3

    peer name                    : Dut-C

    peer name refs               : 1

    src addr conf                : Yes

    source addr                  : 2.1.1.2

    num of mcep                  : 1

    num of non-mcep              : 0

    own sess num                 : 58ba0d39

    mc admin state               : Up

    tlv own mc admin state       : Up

    tlv peer mc admin state      : Up

    reachable                    : Yes

    own sys priority             : 50

    own sys id                   : 00:03:fa:72:c3:c0

    peer sys priority            : 21

    peer sys id                  : 00:03:fa:c6:31:f8

    master                       : No

    conf boot timer              : 300

    boot timer active            : No

    conf ka intv                 : 10

    conf hold on num of fail     : 3

    tlv own ka intv              : 10

    tlv peer ka intv             : 10

    ka timeout tmr active        : Yes

    ka timeout tmr intvl         : 20

    ka timeout tmr time left     : 4

    peer ka intv                 : 10

    mc peer timed out            : No

    initial peer conf rx         : Yes

    peer-mc disabled             : No

    initial peer conf sync       : Yes

    peer conf sync               : Yes

    own passive mode             : Disable

    peer passive mode            : No

    retransmit pending           : No

    non-mcep retransmit pending  : No

    retransmit intvl             : 5

    last tx time                 : 1437130

    last rx time                 : 1437156

    own bfd                      : Enable

    peer bfd                     : Enable

    bfd vrtr if                  : 2

    bfd handle                   : 1

    bfd state                    : 3

    bfd code                     : 0

*A:Dut-B#

Syntax

mc-ring peer ip-address [ring sync-tag]

Context

This command dumps multi-chassis ring information.

Description

peer ip-address

ring sync-tag

Specifies the ring’s sync-tag created in the config>redundancy>mc>peer>mcr> ring context.

sync-database

Syntax

sync-database [peer ip-address] [port port-id | lag-id] [sync-tag sync-tag] [application application] [detail] [type type]

Context

This command dumps MCS database information.

Description

peer ip-address

Indicates the port or LAG ID to be synchronized with the multi-chassis peer.

port port-id | lag-id

slot/mda/port or lag-lag-id

sync-tag sync-tag

Specifies a synchronization tag to be used while synchronizing this port with the multi-chassis peer.

application application

Specifies a particular multi-chassis peer synchronization protocol application.

Values

dhcp-server: local dhcp server
igmp: Internet group management protocol
igmp-snooping: igmp-snooping
mc-ring : multi-chassis ring
mld-snooping: multicast listener discovery-snooping
srrp: simple router redundancy protocol
sub-host-trk: subscriber host tracking
sub-mgmt: subscriber management

type type

Indicates the locally deleted or alarmed deleted entries in the MCS database per multi-chassis peer.

Values

alarm-deleted, local-deleted

Displays detailed information.

srrp-sync-data

Syntax

srrp-sync-database [instance instance-id] [peer ip-address]

Context

This command dumps SRRP database information.

Description

peer ip-address

Dumps information for the specified Subscriber Router Redundancy Protocol instance configured on this system.

instance instance-id

Values

1 — 4294967295

Syntax

tools>perform>redundancy>mgmt-ethernet

Context

Description

This command triggers redundancy mode, just as if the management Ethernet port of the primary CPM has gone down. The router will revert if the management Ethernet port of the primary CPM has been up for the revert duration.

set-fabric-speed

Syntax

set-fabric-speed speed

Context

tools>perform

Description

This command sets fabric speed. With the introduction of SFM5-12e and the mini-SFM5-12e, a new tools command (set-fabric-speed) was added to set the fabric operating speed. (tools command does not apply to SFM4-12e) fabric-speed-a).

Parameters

fabric-speed-a

The 7750 SR-12e chassis defaults to the fabric-speed-a when initially deployed with SFM5-12e. It operates at 200GB per slot which permits a mixture of FP2/FP3 based cards to co-exist.

fabric-speed-b

Eenables the 7750 SR-12e to operate at up to 400 Gb/s, for which all cards in the 7750 SR-12e are required to be T3 based (FP3 IMM and/or IOM3-XP-C). The system will not support any FP2 based cards when the chassis is set to fabric-speed-b.

stop

Syntax

stop [script-policy-name] [owner script-policy-owner] [all]

Context

tools>perform>system>script-control>script-policy

Description

This command stops the execution of scripts.

Parameters

script-policy-name

Only stop scripts with the specified script-policy.

owner script-policy-owner

Only stop scripts that are associated with script-policies with the specified owner.

Default

“TiMOS CLI”

all

Keyword to stop all running scripts.

customer

Syntax

customer customer-id [site customer-site-name]

Context

This command is used to re-evaluate the time-of-day state of a multi-service site.

Description

Parameters

customer-id

Re-evaluate time-of-day state of a specific customer.

Values

1 to 2147483647

customer-site-name

Re-evaluate time-of-day state of a specific customer site. 32 characters max.

filter

Syntax

filter {ip-filter | ipv6-filter | mac-filter}

Context

This command is used to re-evaluate the time-of-day state of a filter entry.

Description

Parameters

ip-filter

Re-evaluate time-of-day state of an IP filter entry.

ipv6-filter

Re-evaluate time-of-day state of an IPv6 filter entry.

mac-filter

Re-evaluate time-of-day state of a MAC filter entry.

service

Syntax

service service-id [sap sap-id]

Context

This command is used to re-evaluate the time-of-day state of a SAP.

Description

Parameters

service-id

Re-evaluate time-of-day state of a specific service.

Values

1 to 2148007978 | svc-name: 64 characters max

sap-id

Re-evaluate time-of-day state of a specific SAP.

Values

sap-id null port-id|bundle-id|bpgrp-id|lag-id|aps-id>
dot1q port-id|bundle-id|bpgrp-id|lag-id| aps-id|pw-id>:qtag1
qinq port-id|bundle-id|bpgrp-id|lag-id|pw-id>:qtag1.qtag2
atm <port-id|aps-id>[:vpi/vci|vpi|vpi1.vpi2|cp.conn-prof-id]
cp keyword
conn-prof-id 1..8000
frame port-id|aps-id:dlci
cisco-hdlc slot/mda/port.channel
cem slot/mda/port.channel
ima-grp bundle-id>[:vpi/vci|vpi|vpi1.vpi2|cp.conn-prof-id]
cp keyword
conn-prof-id 1..8000
port-id slot/mda/port[.channel]
bundle-id bundle-<type>-slot/mda.bundle-num
bundle keyword
type ima, fr, ppp
bundle-num 1..336
bpgrp-id bpgrp-<type>-<bpgrp-num>
bpgrp keyword
type ima, ppp
bpgrp-num 1..2000
aps-id aps-<group-id>[.channel]
aps keyword
group-id 1..64
ccag-id ccag-id.path-id[cc-type]<cc-id
ccag keyword
id 1..8
path-id a, b
cc-type .sap-net, .net-sap
cc-id 0..4094
eth-tunnel eth-tunnel-id[:eth-tun-sap-id]
id 1..1024
eth-tun-sap-id 0..4094
lag-id lag-id
lag keyword
id 1..800
pw-id pw-id
pw keyword
id 1..10239
qtag1 *, 0..4094
qtag2 *|0..4094
vpi 0..4095 (NNI)
0..255 (UNI)
vci 1, 2, 5..65535
dlci 16..1022
tunnel-id tunnel-id.private|public:tag
tunnel keyword
id 1..16
tag 0..4094

tod-suite

Syntax

tod-suite [tod-suite-name]

Context

This command is used to re-evaluate the time-of-day state for objects referring to a tod-suite.

Description

Parameters

tod-suite-name

Re-evaluate time-of-day state for all objects referring to a specific tod-suite. 32 characters maximum.

Clear Commands

application-assurance

Syntax

application-assurance

Context

This command clears application assurance commands.

Description

group

Syntax

group isa-aa-group-id statistics

group isa-aa-group-id status

Context

clear>app-assure

Description

This command clears application assurance group data.

Parameters

isa-aa-group-id

Specifies the ISA-AA group index.

Values

status

Specifies that application assurance system statistics are cleared.

Specifies that application assurance statistics are cleared.

Syntax

Context

This command enables the context to clear redundancy parameters.

Description

Syntax

This command enables the context to clear multi-chassis parameters.

Context

clear>redundancy

Description

mc-mobile

Syntax

mc-mobile statistics peer {ip-address | ipv6-address}

Context

clear>redundancy

Description

This command enables the context to clear multi-chassis parameters.

mc-endpoint

Syntax

mc-endpoint endpoint [mcep-id] statistics

mc-endpoint statistics

mc-endpoint peer [ip-address] statistics

Context

This command clears multi-chassis endpoint statistics.

Description

endpoint mcep-id

Clears information for the specified multi-chassis endpoint ID.

Values

1 — 4294967295

peer ip-address

Clears information for the specified peer IP address.

Clears statistics for this multi-chassis endpoint.

mc-lag

Syntax

mc-lag [peer ip-address [lag lag-id]]

Context

This command clears multi-chassis Link Aggregation Group (LAG) information.

Description

Parameters

peer ip-address

Clears the specified address of the multi-chassis peer.

lag lag-id

Clears the specified LAG on this system.

Values

1 — 100

Syntax

Context

This command clears multi-chassis ring data.

Description

debounce

Syntax

debounce peer ip-address ring sync-tag

Context

This command clears multi-chassis ring operational state debounce history.

Description

Parameters

Clears debounce history for the specified IP address.

ring sync-tag

Clears debounce history for the specified sync tag.

ring-nodes

Syntax

ring-nodes peer ip-address ring sync-tag

Context

clear>redundancy>multi-chassis>mcr

Description

This command clears multi-chassis ring unreferenced ring nodes.

Parameters

Clears ring statistics for the specified IP address.

ring sync-tag

Clears ring statistics for the specified sync tag.

Syntax

clear>redundancy>multi-chassis>mcr

Context

Description

This command clears multi-chassis ring

global

Syntax

global

Context

This command clears multi-chassis ring global statistics.

Description

Syntax

peer ip-address

Context

This command clears multi-chassis ring peer statistics.

Description

Parameters

Clears ring peer statistics for the specified IP address.

ring

Syntax

ring peer ip-address ring sync-tag

Context

This command clears multi-chassis ring statistics.

Description

Parameters

Clears ring statistics for the specified IP address.

ring sync-tag

Clears ring statistics for the specified sync tag.

ring-node

Syntax

ring-node peer ip-address ring sync-tag node ring-node-name

Context

This command clears multi-chassis ring statistics.

Description

Parameters

peer ip-address

Clears ring-node peer statistics for the specified IP address.

ring sync-tag

Clears ring-node peer statistics for the specified sync-tag.

node ring-node-name

Clears ring-node peer statistics for the specified ring node name.

ptp

Syntax

ptp inactive-peers

ptp statistics

ptp peer ip_address statistics

Context

clear>system

Description

This command clears PTP statistics.

Parameters

inactive-peers

Removes PTP peers which are not currently exchanging PTP packets with the router.

peer ip-address statistics

Clears statistics for the specified peer.

Clears all ptp statistics.

sync-database

Syntax

sync-database peer ip-address all application application

sync-database peer ip-address {port port-id | lag-id | sync-tag sync-tag } application application

sync-database peer ip-address port port-id | lag-id sync-tag sync-tag application application

Context

This command clears multi-chassis sync database information.

Description

Parameters

peer ip-address

Clears the specified address of the multi-chassis peer.

port port-id

Clears the specified port ID of the multi-chassis peer.

port lag-id

Clears the specified Link Aggregation Group (LAG) on this system.

all

Clears all ports and/or sync tags.

sync-tag sync-tag

Clears the synchronization tag used while synchronizing this port with the multi-chassis peer.

application

Clears the specified application information that was synchronized with the multi-chassis peer.

Values

all: All supported applications
dhcp-server: local dhcp server
igmp: internet group management protocol
igmp-snooping: igmp-snooping
mc-ring: multi-chassis ring
mld-snooping: multicast listener discovery-snooping
srrp: simple router redundancy protocol
sub-host-trk subscriber host tracking
sub-mgmt: subscriber management

screen

Syntax

screen

Context

This command allows an operator to clear the Telnet or console screen.

Description

system

Syntax

system sync-if-timing {ref1 | ref2 | bits}

Context