For feedback and comments:
documentation.feedback@alcatel-lucent.com

Table of Contents Previous Next PDF


WIFI Aggregation and Offload Commands
Generic Commands
description
Syntax
description description-string
no description
Context
config>aaa>acct-on-off-grp
config>aaa>radius-server-policy
config>isa>wlan-gw-group
config>router>radius-server>server
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
config>service>vprn>radius-server>server
config>subscr-mgmt>wlan-gw>mgw-profile
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6
Description
This command creates a text description stored in the configuration file for a configuration context.
The description command associates a text string with a configuration context to help identify the context in the configuration file.
The no form of this command removes any description string from the context.
Default
No description is associated with the configuration context.
Parameters
description-string
A text string describing the entity. Allowed values are any string up to 80 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
shutdown
Syntax
[no] shutdown
Context
config>router>radius-proxy>cache
config>router>radius-proxy>server>cache
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server>cache
config>service>vprn>radius-proxy>server
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface>group-interface>wlan-gw
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>slaac
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>slaac
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>ia-na
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>ia-na
Description
The shutdown command administratively disables the entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics. Many entities must be explicitly enabled using the no shutdown command.
The shutdown command administratively disables an entity. The operational state of the entity is disabled as well as the operational state of any entities contained within. Many objects must be shut down before they can be deleted.
Unlike other commands and parameters where the default state is not indicated in the configuration file, shutdown and no shutdown are always indicated in system generated configuration files.
The no form of the command puts an entity into the administratively enabled state.
Default
no shutdown
subscriber-mgmt
Syntax
subscriber-mgmt
Context
config
Description
This command enables the context to configure subscriber management entities. A subscriber is uniquely identified by a subscriber identification string. Each subscriber can have several DHCP sessions active at any time. Each session is referred to as a subscriber host and is identified by its IP address and MAC address.
All subscriber hosts belonging to the same subscriber are subject to the same hierarchical QoS (HQoS) processing. The HQoS processing is defined in the sub-profile (the subscriber profile). A sub-profile refers to an existing scheduler policy (configured in the configure>qos>scheduler-policy context) and offers the possibility to overrule the rate of individual schedulers within this policy.
Because all subscriber hosts use the same scheduler policy instance, they must all reside on the same complex.
 
WLAN-GW Commands
Note that the wlan-gw commands apply only to the 7750 SR platform.
wlan-gw
Syntax
[no] wlan-gw
Context
config>subscriber-mgmt
config>router
config>service>vprn
Description
This command enables the context to configure WLAN Gateway parameters.
 
distributed-sub-mgt
Syntax
distributed-sub-mgmt
Context
config>subscr-mgmt>wlan-gw
Description
This command enables the context to configure profiles, templates, and policies that can be applied to DSM subscribers.
dsm-ip-filter
Syntax
dsm-ip-filter filter-name
no dsm-ip-filter filter-name
Context
config>subscr-mgmt>wlan-gw>dsm
Description
This command configures a set of filter rules that can be applied to a DSM UE.
The no form of the command can only be executed if no entries are configured under this filter.
Default
none
Parameters
filter-name
Specifies the name of the filter.
description
Syntax
description description-string
no description
Context
config>subscr-mgmt>wlan-gw>dsn>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6>entry
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command creates a text description stored in the configuration file for a configuration context.
The description command associates a text string with a configuration context to help identify the context in the configuration file.
The no form of the command removes any description string from the context.
Default
none
Parameters
description-string
A text string describing the entity. Allowed values are any string up to 80 characters long composed of printable, 7-bit ASCII characters, excluding double quotation marks (“ ”). If the string contains special characters (such as #, $, spaces, etc.), the entire string must be enclosed in double quotation marks (“ ”).
default-action
Syntax
default-action {drop|forward}
no default-action
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6
Description
This command specifies what should happen to packets that do not match any of the configured entries.
The no form of the command reverts to the default value.
Default
default-action drop
Parameters
drop
Drops the packet.
forward
Forwards the packet.
entry
Syntax
entry entry-id [create]
no entry entry-id
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6
Description
This command creates a new entry for this filter. When processing a packet, entries are matched in order, starting with the lowest entry-id. A maximum of 128 IPv4 and 128 IPv6 DSM filter entries are allowed.
The no form of the command reverts to the default value.
Default
none
Parameters
entry-id
The numeric identifier for the filter entry.
 
action
Syntax
action {drop|forward|none}
no action
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6>entry
Description
This command specifies what should happen to packets that do match this entry. If the configured action is none, this entry is not applied and processing continues to match against subsequent entries.
The no form of the command reverts to the default value.
Default
action none
Parameters
drop
Drops the packet.
forward
Forwards the packet.
none
Disables this entry. Packet processing continues with the next entry.
match
Syntax
match protocol {any|icmp|tcp|upd|gre}
no match
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6>entry
Description
This command creates a match context for this entry. The protocol value specifies which Layer-4
protocol the packet should match.
The no form of the command removes the match context of this entry.
Default
no match
Parameters
protocol
The only supported match context is protocol.
any
Matches any protocol.
icmp
Matches ICMP packets in a v4 filter.
tcp
Matches TCP packets.
udp
Matches UDP packets.
gre
Matches GRE over IP packets.
dst-port
Syntax
dst-port operator <port-number>
no dst-port
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>entry>match
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6>entry>match
Description
This command specifies that the packet’s UDP/TCP dst-port must match a specific value. This command is not valid in a match context that is not specific to UDP or TCP.
The no form of the command removes matching of the layer-4 port.
Default
no dst-port
Parameters
operator
The only supported value is eq (equal to); the destination port value must be equal to the port-number value.
port-number
[0..65535] The number of the port to match.
dst-ip
Syntax
dst-ip ip-prefix/length
no dst-ip
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>entry>
Description
This command specifies that the packet’s destination IP address must match the specified IP prefix and mask.
The no form of the command disables the match on the destination IP.
Default
no dst-ip
Parameters
ip-prefix/length
The IP prefix to match.
dsm-policer
Syntax
dsm-policer policer-name [type {single-bucket-bandwidth|dual-bucket-bandwidth}][create]
no dsm-policer policer-name
Context
config>subscr-mgmt>wlan-gw>dsm>
Description
This command creates a policer profile that can be applied to a DSM host. When creating a profile the first time, the create and type parameters are required.
The WLAN-GW allows configuration of single-rate and dual-rate bucket policers.
The no form of the command removes the profile.
Default
none
Parameters
policer-name
The name by which this policer is referenced.
single-bucket-bandwidth
One rate is applied per policer.
dual-bucket-bandwidth
The policer applies a CIR and a PIR.
action
Syntax
action {permit-deny|priority-mark}
no action
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies what happens to packets that are in-profile and out-of-profile.
The no form of the command reverts to the default value.
Default
action permit-deny
Parameters
permit-deny
Drop all packets that are out of profile (do not conform to the PIR).
priority-mark
Currently not supported. The policer will take no action.
adaptation-rule
Syntax
adaptation-rule pir {max|min|closest} [cir {max|min|closest}]
no adaptation-rule
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies what happens to packets that are in-profile and out-of-profile.
The no form of the command reverts to the default value.
Default
action permit-deny
Parameters
max
The operational rate at its maximum may be the configured rate. The first operational value that is smaller or equal to the configured rate will be chosen.
min
The operational rate at its minimum must be the configured rate. The first operational value that is bigger or equal to the configured rate will be chosen.
closest
The system chooses the operational value—either lower or higher—that is closest to the configured value.
cbs
Syntax
cbs burst-size
no cbs
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies the committed burst-size value of this policer. This can only be set on dual-bucket-bandwidth policers.
The no form of the command reverts to the default value.
Default
cbs 0
Parameters
burst-size
[0..131071] The committed burst-size in kilobytes.
mbs
Syntax
mbs burst-size
no mbs
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies the maximum burst-size value of this policer. This can only be set on dual-bucket-bandwidth policers.
The no form of the command reverts to the default value.
Default
mbs 0
Parameters
burst-size
[0..131071] The maximum burst-size in kbytes.
rate
Syntax
rate rate [cir rate]
no rate
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies the rate at which the policer drains packets. The cir rate value is only supported on dual-bucket-bandwidth policers. If rate max is configured, no rate limitations are applied.
The no form of the command reverts to the default value.
Default
rate max
Parameters
rate
[1..100000000|max] the rate in kb/s
mgw-profile
Syntax
mgw-profile profile-name [create]
no mgw-profile profile-name
Context
config>subscr-mgmt>wlan-gw
Description
This command creates a new mobile gateway profile or configures an existing mobile gateway profile.
Mobile gateway profile is used to configure signaling interface between WLAN-GW and mobile gateway (PGW or GGSN) and GTP related signaling parameters per mobile gateway.
The no form of the command removes the profile name from the configuration.
Default
none
Parameters
profile-name
Specifies the Mobile Gateway profile up to 32 characters in length.
create
Keyword used to create a profile name. The create keyword requirement can be enabled/disabled in the environment>create context.
interface-type
Syntax
interface-type {gn|s2a|s2b}
no interface-type
Context
config>subscriber-mgmt>wlan-gw >mgw-profile
Description
This command specifies the signaling interface between WLAN-GW and mobile gateway (PGW or GGSN).
Default
s2a
Parameters
gn
Signaling interface between wlan-gw and mobile gateway is Gn as specified in 3GPP TS 29.060.
S2a
Signaling interface between wlan-gw and mobile gateway is S2a as specified in SAMOG.
S2b
Signaling interface between wlan-gw and mobile gateway is S2b as specified in 3GPP TS 29.274.
ip-ttl
Syntax
ip-ttl hops
no ip-ttl
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command configures the value to put in the IP header’s TTL field for GTP control messages.
The no form of the command reverts to the default value.
Default
255
Parameters
hops
Specifies the IP TTL.
Values
keep-alive
Syntax
keep-alive [interval seconds] [retry-count value] [timeout retry-seconds]
no keep-alive
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command configures the context in radius-server-policy.
The no form of the command reverts to the default values.
Default
keep-alive interval 60 seconds, retry-count 5, timeout 5 seconds
Parameters
interval seconds
Specifies, in seconds, the interval between keep-alive Echo-Request messages towards the same peer.
Values
Default
retry-count value
Specifies, in seconds, the interval between keep-alive Echo-Request messages towards the same peer.
Values
Default
timeout retry-seconds
Specifies the retry timeout, in seconds.
Values
Default
message-retransmit
Syntax
message-retransmit [timeout timeout] [retry-count value]
no message-retransmit
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command configures the retry-count and response-timeout for GTP messages.
The no form of the command reverts to the default values.
Default
timeout 5 seconds, value 3
Parameters
timeout timeout
specifies, in seconds, the interval between retransmission of signalling request messages towards the same peer Mobile Gateway.
Values
Default
retry-count value
specifies the number of times a signalling request message is transmitted towards the same peer.
Values
Default
report-wlan-location
report-wlan-location
no report-wlan-location
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command enables reporting the WLAN location or cellular location of the UE in the signaling interface (S2a or Gn) between wlan-gw and mobile gateway (PGW or GGSN).
The no form of the command disables location reporting.
Default
not enabled
signalling-protocol
signalling-protocol protocol
no signalling-protocol
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command specifies the GTP (GPRS Tunneling Protocol) control protocol.
The no form of the command reverts to the default value.
Default
gtpv1C
Parameters
protocol
Specifies the the GTP control protocol variant.
Values
serving-network
Syntax
serving-network mcc mcc-value mnc mnc-value
no serving-network
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command configures the Operator Identifier part (MCC and MNC) of the APN.
The no form of the command removes the values from the profile.
Default
no serving-network
Parameters
mcc mcc-value
specifies the Mobile Country Code (MCC) portion of the Serving Network.
Values
mnc mnc-value
specifies the Mobile Network Code (MNC) portion of the Serving Network.
Values
virtual-chassis-identifier
Syntax
virtual-chassis-identifier dual-homing-key
no virtual-chassis-identifier
Context
config>subscr-mgmt>wlan-gw>mgw-profile
Description
This command specifies a virtual chassis identifier that can link two wlan-gw’s together.
The no form of the command removes the dual-homing-key
Default
none
Parameters
dual-homing-key
Specifies the name of the dual homing key up to 16 characters.
apn
Syntax
apn apn
no apn
Context
config>router>wlan-gw
configure>service>vprn>wlan-gw
Description
This command configures the Network Identifier part of the APN.
The no form of the command removes the string from the configuration.
Default
no apn
Parameters
apn
Specifies the APN (Access Point Name) used for this IMSI to connect to this Mobile Gateway up to 80 characters in length.
distributed-sub-mgmt
Syntax
distributed-sub-mgmt
Context
config>router>wlan-gw
config>service>vprn>wlan-gw
Description
This command enables the context to configure profiles, templates and policies that can be applied to DSM subscribers.
ipv6-tcp-mss-adjust
Syntax
ipv6-tcp-mss-adjust segment-size
no ipv6-tcp-mss-adjust
Context
config>router>wlan-gw>dsm
config>service>wlan-gw>dsm
Description
This command specifies the value used for TCP-MSS-adjust in the IPv6 upstream direction for DSM. The downstream direction for both IPv4 and IPv6 are both configured under the group-interface. The upstream direction for IPv4 NAT hosts is configured under the NAT policy.
The defined segment size is inserted in a TCP SYN message if there is no existing MSS option or the value in the MSS option is bigger than the configured value.
The no form of the command disables upstream TCP MSS adjust for IPv6 DSM.
Default
no ipv6-tcp-mss-adjust
Parameters
segment-size
Specifies the segment size to be inserted.
Values
mgw-map
Syntax
mgw-map ip-prefix [/prefix-length] mgw-profile profile-name
no mgw-map
Context
config>router>wlan-gw
configure>service>vprn>wlan-gw
Description
This command configures the mappings of MGW IP address and GTP profile.
Parameters
ip-prefix[/prefix-length]
Specifies the IP prefix and prefix length.
Values
profile-name
specifies the profile associated with this address prefix.
Values
address
Syntax
address ip-prefix[/prefix-length] [mgw-profile profile-name]
no address ip-prefix[/prefix-length]
Context
config>router>wlan-gw>mgw-map
configure>service>vprn>wlan-gw>mgw-map
Description
This command specifies the address .
The no form of the command removes the parameters form the configuration.
ip-prefix[/prefix-length
Specifies the IP prefix and prefix length of the subnet.
Values
mgw-profile profile-name
specifies the Mobile Gateway profile associated with this address prefix up to 32 characters in length.
mobility-triggered-acct
Syntax
mobility-triggered-acct
Context
config>router>wlan-gw
configure>service>vprn>wlan-gw
Description
This command enters the configuration context of mobility-triggered-accounting in wlan-gw context under router or VPRN service.
Default
none
interim-update
Syntax
interim-update
no interim-update
Context
config>router>wlan-gw>mobility-triggered-acct
configure>service>vprn>wlan-gw>mobility-triggered-acct
Description
This command enables generation of a flash interim accounting-update to the accounting service when change in location of the UE is detected.
The no form of the command disables generation of flash interim accounting- update to RADIUS when change in location of the UE is detected.
Default
Not enabled
 
RADIUS Server Policy Commands
acct-on-off-group
Syntax
acct-on-off-group group-name [create]
no acct-on-off-group group-name
Context
config>aaa
Description
This command creates an acct-on-off-group.
An acct-on-off-group can be referenced by:
The no form of the command deletes the acct-on-off-group.
Default
none
Parameters
group-name
Specifies the name of an acct-on-off group up to 32 characters in length.
radius-server-policy
Syntax
radius-server-policy policy-name [create]
no radius-server-policy policy-name
Context
config>aaa
Description
This command creates a radius-server-policy.
A radius-server-policy can be used in
- radius-proxy, for application like EAP authentication for WIFI access
- authentication policy, for Enhanced Subscriber Management authentication
- radius accounting policy, for Enhanced Subscriber Management accounting
- dynamic data service RADIUS accounting
- AAA route downloader
The no form of the command removes the policy name from the configuration.
Default
none
Parameters
policy-name
Specifies the name of the radius-server-policy up to 32 characters in length.
create
Keyword used to create a radius-server-policy name. The create keyword requirement can be enabled/disabled in the environment>create context.
accept-script-policy
Syntax
accept-script-policy policy-name
no accept-script-policy
Context
config>aaa>radius-server-policy
Description
This command specifies name of the radius-script-policy to be applied for access-accept.
Default
none
Parameters
policy-name
Specifies the name of the accept-script-policy up to 32 characters in length.
acct-on-off
Syntax
acct-on-off
acct-on-off monitor-group group-name
acct-on-off oper-state-change [group group-name]
Context
config>aaa>radius-server-policy
Description
This command controls the sending of Accounting-On and Accounting-Off messages and the acct-on-off oper-state of the radius-server-policy:
acct-on-off: enables the sending of Accounting-On and Accounting-Off messages for this radius-server-policy. The acct-on-off oper-state is always not blocked.
acct-on-off oper-state-change [group group-name]: enables the sending of Accounting-On and Accounting-Off messages for this radius-server-policy. The acct-on-off oper-state is function of the Accounting-response received for the Accounting-On and Accounting-Off. Optionally, sets the acct-on-off oper-state of the acct-on-off-group.
acct-on-off monitor-group group-name: no Accounting-On and Accounting-Off messages are sent for this radius-server-policy. The acct-on-off oper-state is inherited from the acct-on-off-group.
The no form of the command disables the sending of Accounting-On and Accounting-Off messages.
Default
no acct-on-off
Parameters
group-name
Specifies the name of an acct-on-off group up to 32 characters in length.
acct-on-off-group
Syntax
acct-on-off-group <group-name> [create]
no acct-on-off-group <group-name>]
Context
config>aaa
Description
This command creates an acct-on-off-group.
An acct-on-off-group can be referenced by:
-a single radius-server-policy as controller: the acct-on-off oper-state of the acct-on-off-group is set to the acct-on-off oper-state of the radius-server-policy (acts as master)
-multiple radius-server-policies as monitor: the acct-on-off oper-state of the radius-server-policy is inherited from the acct-on-off oper-state of the acct-on-off group. (acts as a slave)
The no form of the command deletes the acct-on-off-group.
Default
none
Parameters
group-name
Specifies the name of an acct-on-off group up to 32 characters in length.
acct-request-script-policy
Syntax
acct-request-script-policy policy-name
no acct-request-script-policy
Context
config>aaa>radius-server-policy
Description
This command specifies the name of the acct-request-script-policy pointing to the Python script to be applied for RADIUS accounting request messages.
Default
no acct-request-script-policy
Parameters
policy-name
Specifies the name of the acct-request-script-policy up to 32 characters in length.
auth-request-script-policy
Syntax
uth-request-script-policy policy-name
no auth-request-script-policy
Context
config>aaa>radius-server-policy
Description
This command specifies the name of the auth-request-script-policy pointing to the Python script to be applied for RADIUS access request messages.
Default
no auth-request-script-policy
Parameters
policy-name
Specifies the name of the auth-request-script-policy up to 32 characters in length.
buffering
Syntax
[no] buffering
Context
config>aaa>radius-server-policy
Description
This command enables the context to configure RADIUS message buffering.
The no form of the command disables RADIUS message buffering.
Default
none
acct-interim
Syntax
acct-interim min min-val max max-val lifetime lifetime
no acct-interim
Context
config>aaa>radius-srv-plcy>servers>buffering
Description
This command enables RADIUS accounting interim update message buffering.
1- The message is stored in the buffer, a lifetime timer is started and the message is sent to the RADIUS server
2- If after retry*timeout seconds no RADIUS accounting response is received for the interim update then a new attempt to send the message is started after minimum[(min-val*2n), max-val] seconds.
3- Repeat step 2 until for one of the following:
a. a RADIUS accounting response is received.
b. the lifetime of the buffered message expires.
c. a new RADIUS accounting interim-update or a RADIUS accounting stop for the same accounting session-id and radius-server-policy is stored in the buffer.
d. the message is manually purged from the message buffer via a clear command.
4- The message is purged from the buffer.
The no form of the command disables RADIUS accounting interim update message buffering.
Default
no acct-interim
Parameters
min-val
Specifies the minimum interval in seconds between attempts to resend the RADIUS accounting interim update
Values
max-val
Specifies the maximum interval in seconds between attempts to resend the RADIUS accounting interim update
Values
lifetime
Specifies the lifetime in hours
Values
acct-stop
Syntax
acct-stop min min-val max max-val lifetime lifetime
no acct-stop
Context
config>aaa>radius-srv-plcy>servers>buffering
Description
This command enables RADIUS accounting stop message buffering.
1- The message is stored in the buffer, a lifetime timer is started and the message is sent to the RADIUS server
2 - If after retry*timeout seconds no RADIUS accounting response is received for the accounting stop, then a new attempt to send the message is started after minimum[(min-val*2n), max-val] seconds.
3 - Repeat step 2 until
a. a RADIUS accounting response is received, or
b. the lifetime of the buffered message expires, or
c. the message is manually purged from the message buffer via a clear command
4 - The message is purged from the buffer.
The no form of the command disables RADIUS accounting stop message buffering..
Default
no acct-interim
Parameters
min-val
Secifies the minimum interval in seconds between attempts to resend the RADIUS accounting stop
Values
max-val
Specifies the maximum interval in seconds between attempts to resend the RADIUS accounting stop.
Values
max-val
Specifies the lifetime in hours.
Values
servers
Syntax
servers
Context
config>aaa>radius-server-policy
Description
This command enables the context to configure radius-server-policy parameters.
access-algorithm
Syntax
access-algorithm {direct|round-robin|hash-based}
no access-algorithm
Context
config>aaa>radius-server-policy>servers
Description
This command configures the algorithm used to select a RADIUS server from the pool of configured RADIUS servers.
Default
direct
Parameters
direct
Specifies that the first server will be used as primary server for all requests, the second as secondary and so on.
round-robin
Specifies that the first server will be used as primary server for the first request, the second server as primary for the second request, and so on. If the router gets to the end of the list, it starts again with the first server.
hash-based
Select a RADIUS server based on the calculated hash result of the configured load-balance-key under the radius-proxy server hierarchy. This parameter is only applicable for radius-proxy server scenarios and results in an unpredictable RADIUS server selection if used in other scenarios.
retry
Syntax
retry count
no retry
Context
config>aaa>radius-srv-plcy>servers
Description
This command configures the number of times the router attempts to contact the RADIUS server, if not successful the first time.
Default
3
Parameters
count
Specifies the number of times a signalling request message is transmitted towards the same peer.
Values
router
Syntax
router router-instance
router service-name service-name
no router
Context
config>aaa>radius-server-policy>servers
Description
This command specifies the virtual router instance applicable for the set of configured RADIUS servers. This value cannot be changed once a RADIUS server is configured for this policy.
Default
no router
Parameters
router-instance
Specifies the router instance.
Values
service-name
Specifies the router name service-id up to 64 characters.
server
Syntax
server server-index name server-name
no server server-index
Context
config>aaa>radius-server-policy>servers
Description
This command adds a RADIUS server.
The no form of the command removes a RADIUS server.
Default
none
Parameters
index
The index for the RADIUS server. The index determines the sequence in which the servers are queried for authentication requests. Servers are queried in order from lowest to highest index.
Values
server-name
Specifies the server name up to 32 characters in length.
source-address
Syntax
source-address ip-address
no source-address
Context
config>aaa>radius-server-policy>servers
Description
This command configures the source address of the RADIUS packet. The system IP address must be configured in order for the RADIUS client to work. See Configuring a System Interface in the 7750 SR OS Router Configuration Guide. Note that the system IP address must only be configured if the source-address is not specified. When the no source-address command is executed, the source address is determined at the moment the request is sent. This address is also used in the nas-ip-address attribute: over there it is set to the system IP address if no source-address was given.
The no form of the command reverts to the default value.
Default
no source-address
Parameters
ip-address
Specifies the source address of radius packet.
timeout
Syntax
timeout [sec seconds] [min minutes]
no timeout
Context
config>aaa>radius-srv-plcy>servers
Description
This command configures the time the router waits for a response from a RADIUS server.
The no form of the command reverts to the default value.
Default
5 seconds
Parameters
seconds
Specifies the number of seconds for the timeout.
Values
minutes
Specifies the number of minutes for the timeout.
Values
Values
hold-down-time
Syntax
hold-down-time [sec seconds] [min minutes]
no hold-down-time
Context
config>aaa>radius-server-policy>servers
Description
This command configures the hold time before re-using a RADIUS server.
The no form of the command reverts to the default value.
Default
30 seconds
Parameters
seconds
Specifies the number of seconds for the hold down time.
Values
minutes
Specifies the number of minutes for the hold down time.
Values
ipv6-source-address
Syntax
ipv6-source-address ipv6-address
no ipv6-source-address
Context
config>aaa>radius-server-policy>servers
Description
This command configures the source address of an IPv6 RADIUS packet.
When no ipv6-source-address is configured, the system IPv6 address (inband RADIUS server connection) or Boot Option File (BOF) IPv6 address (outband RADIUS server connection) must be configured in order for the RADIUS client to work with an IPv6 RADIUS server.
This address is also used in the NAS-IPv6-Address attribute.
The no form of the command reverts to the default value.
Default
no ipv6-source-address
Parameters
ipv6-address
Specifies the source address of an IPv6 RADIUS packet.
CLI Command Description for RADIUS Server
radius-server
Syntax
radius-server
Context
config>router
config>service>vprn
Description
This command enters the radius-server configuration context under router or VPRN service.
Default
none
server
Syntax
server server-name [address ip-address] [secret key][hash|hash2][create]
no server server-name
Context
config>router>radius-server
config>service>vprn>radius-server
Description
This command either specifies an external RADIUS server in the corresponding routing instance or enters configuration context of an existing server. The configured server could be referenced in the radius-server-policy.
The no form of the command removes the parameters from the server configuration.
Default
no
Parameters
server-name
Specifies the name of the external RADIUS server
address ip-address
Specifies the IPv4 or IPv6 IP address of the external RADIUS server.
secret key
Specifies the shared secret key of the external RADIUS server
hash
Specifies the hash scheme.
accept-coa
Syntax
[no] accept-coa
Context
config>router>radius-server>server
config>service>vprn>radius-server>server
Description
This command configures this server for Change of Authorization messages. The system will process the CoA request from the external server if configured with this command; otherwise the CoA request will be dropped.
The no form of the command disables the command.
acct-port
Syntax
acct-port port
no acct-port
Context
config>router>radius-server>server
config>service>vprn>radius-server>server
Description
This command specifies the UDP listening port for RADIUS accounting requests.
The no form of the commands resets the UDP port to its default value (1813)
Default
acct-port 1813
Parameters
port
Specifies the UDP listening port for accounting requests of the external RADIUS server.
Values
auth-port
Syntax
auth-port port
no auth-port
Context
config>router>radius-server>server
config>service>vprn>radius-server>server
Description
This command specifies the UDP listening port for RADIUS authentication requests.
The no form of the commands resets the UDP port to its default value (1812)
Default
auth-port 1812
Parameters
port
Specifies the UDP listening port for accounting requests of the external RADIUS server.
Values
coa-script-policy
Syntax
coa-script-policy policy-name
no coa-script-policy
Context
config>router>radius-server>server
config>service>vprn>radius-server>server
Description
This command specifies radius-script-policy for CoA-Request sent from this RADIUS server.
The no form of the command removes the policy name from the configuration.
Default
none
Parameters
policy-name
Specifies the name of radius-script-policy up to 80 characters in length.
pending-requests-limit
Syntax
pending-request-limit limit
no pending-request-limit
Context
config>router>radius-server>server
config>service>vprn>radius-server>server
Description
This command specifies the per-server maximum number of outstanding requests sent to the RADIUS server. If the maximum number is exceeded, the next RADIUS server in the pool is selected.
The no form of the command removes the limit value from the configuration.
Default
none
Parameters
limit
Specifies the maximum number of outstanding requests sent to the RADIUS server
Values
CLI Command Description for RADIUS Proxy Server
radius-proxy
Syntax
radius-proxy
Context
config>router
config>service>vprn
Description
This command context to configure RADIUS proxy parameters.
server
Syntax
server server-name [create] [purpose {[accounting | authentication]}] [wlan-gw-group group-id]
no server server-name
Context
config>router>radius-proxy
config>service>vprn>radius-proxy
Description
This command creates a RADIUS-proxy server in the corresponding routing instance. The proxy server can be configured for the purpose of proxying authentication or accounting or both.
If wlan-gw isa group is specified, then the RADIUS proxy server is instantiated on the set of ISAs in the specified wlan-gw group. The RADIUS messages from the AP are load-balanced to these ISAs. The ISA that processes the RADIUS message then hashes this message to the ISA that anchors the UE. The hash is based on UE MAC address (required to be present in the calling-station-id attribute) in the RADIUS message.
If the create parameter is not specified, then this command enters configuration context of the specified RADIUS-proxy server.
The no form of the command removes the server-name and parameters from the radius-proxy configuration.
Default
purpose authentication
Parameters
server-name
Specifies the name of the RADIUS-proxy server.
create
The creation parameter. The system will create the specified RADUIS-proxy server.
purpose
Specifies the purpose the RADIUS-proxy server,
Values
wlan-gw-group group-id
Specifies the WLAN-GW isa group.
interface
Syntax
[no] interface ip-int-name
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command configures the IP interface the RADIUS-proxy server will bind to. One RADIUS-proxy server could bind to multiple interfaces.
Default
none
Parameters
ip-int-name
Specifies the name of IP interface.
load-balance-key
Syntax
load-balance-key [vendor vendor-id [vendor-id...(up to 5 max)]] attribute-type attribute-type [attribute-type...(up to 5 max)]
load-balance-key source-ip-udp
no load-balance-key
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command specifies the key(s) used in calculating a hash to select an external RADIUS server from the pool of configured servers.
The key(s) can be the source ip and source udp port tuple, or the specified radius attribute(s) in radius packets.
The no form of the command removes the parameters from the configuration.
Default
no load-balance-key
Parameters
vendor vendor-id
Specifies the vendor-id of vendor-specific attribute.
Values
attribute-type attribute-type
Specifies that the key is constructed with the attributes in the RADIUS message.
Values
source-ip-udp
Specifies that the key consists of the source IP address and source UDP port of the RADIUS message.
python-policy
Syntax
python-policy name
no python-policy
Context
config>router>radius-proxy>server
Description
This command specifies the Python policy used to change the RADIUS attributes of the different RADIUS messages.
secret
Syntax
secret secret [hash|hash2]
no secret
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command configures the shared secret key. The RADIUS client must have the same key to communicate with the RADIUS-proxy server.
The no form of the command removes the parameters from the configuration.
Default
none
Parameters
secret key
The secret key to access the RADIUS server. This secret key must match the password on the RADIUS server.
Values
hash
Specifies the key is entered in an encrypted form. If the hash parameter is not used, the key is assumed to be in a non-encrypted, clear text form. For security, all keys are stored in encrypted form in the configuration file with the hash parameter specified.
hash2
Specifies the key is entered in a more complex encrypted form. If the hash2 parameter is not used, the less encrypted hash form is assumed.
default-accounting-server-policy
Syntax
default-accounting-server-policy policy-name
no default-accounting-server-policy
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command specifies the default radius-server-policy for RADIUS accounting. This policy will be used when there is no specific match based on username.
The no form of the command removes the policy name from the configuration.
Default
none
Parameters
policy-name
Specifies the name of the default RADIUS server policy associated with this RADIUS Proxy server for accounting purposes.
default-authentication-server-policy
Syntax
default-authentication-server-policy policy-name
no default-authentication-server-policy
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command specifies the default radius-server-policy for RADIUS authentication. This policy will be used when there is no specific match based on username.
The no form of the command removes the policy name from the configuration.
Default
none
Parameters
policy-name
Specifies the name of the default RADIUS server policy associated with this RADIUS proxy server for authentication purposes.
username
Syntax
username [1..32] [prefix-string prefix-string] [accounting-server-policy policy-name] [suffix-string suffix-string]
no username [1..32]
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command configures a mapping of username prefix to a radius-server-policy for authentication or accounting. The username from incoming authentication or accounting messages is matched against the configured mappings to obtain the radius-server-policy to be used. Up to 32 entries could be configured for a RADIUS-proxy server.
Default
none
Parameters
1..32
Assigns an integer to specify this username.
prefix-string
Specifies a prefix string used to match username attribute up to 128 characters.
policy-name
Specifies a radius-server-policy name up to 32 characters in length.
send-accounting-response
Syntax
[no] send-accounting-response
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command results in the system to always generate RADIUS accounting-response to acknowledge RADIUS accounting-request received from the RADIUS client.
The no form of the command disables the command.
Default
no send-accounting-response
cache
Syntax
cache
Context
config>router>radius-proxy>server
config>service>vprn>radius-proxy>server
Description
This command enters the cache configuration context under radius-proxy server. The cache contains per-subscriber authentication information learnt from RADIUS authentication messages, and is used to authorize subsequent DHCP requests.
Default
none
key
Syntax
key packet-type {accept|request} attribute-type attribute-type [vendor vendor-id]
no key
config>router>radius-proxy>server>cache
config>service>vprn>radius-proxy>server>cache
Description
This command specifies the RADIUS cache key that is used to match the information in subsequent DHCP requests for authorization.
Default
no key
Parameters
packet-type
Specifies the packet type of the RADIUS messages to use to generate the key for the cache of this RADIUS proxy server.
Values
attribute-type attribute-type
Specifies the RADIUS attribute type to cache for this RADIUS proxy server.
Values
the type value of RADIUS attribute
vendor vendor-id
Specifies the RADIUS vendor ID.
Values
timeout
Syntax
timeout [hrs hours] [min minutes] [sec seconds]
no timeout
Context
config>router>radius-proxy>server>cache
config>service>vprn>radius-proxy>server>cache
Description
This command configures the time for which the cache entry is kept if there is no corresponding DHCP DISCOVER. At the expiry of this time, the cache entry is deleted.
The no form of the command reverts to the default value.
Default
timeout min 5
Parameters
hrs hours
Specifies, in seconds, the timeout after which an entry in the cache will expire.
min minutes
Specifies, in seconds, the timeout after which an entry in the cache will expire.
sec seconds
Specifies, in seconds, the timeout after which an entry in the cache will expire.
track-accounting
Syntax
track-accounting [start] [stop][interim-update][accounting-on] [accounting-off]
no track-accounting
Context
config>router>radius-proxy>server>cache
config>service>vprn>radius-proxy>server>cache
Description
This command specifies the type of RADIUS accounting packets from RADIUS client (a WIFI AP) that the router should track.
The no form of the command removes the parameters from the configuration.
Default
no track-accounting
Parameters
start
The router will update the associated ESM-host with the RADIUS client (for example, a WIFI AP) that generated the accounting-start. This is required in cases where a UE roams to a new AP that does not re-authenticate due to key caching.
stop
The router will remove the corresponding ESM host and forward the accounting-stop packet to the external RADIUS server.
accounting-on | accounting-off
The router will remove all ESM hosts associated with the RADIUS client (a WIFI AP), and forward the accounting-on packet to the external RADIUS server.
interim-update
The router will update the associated ESM-host with the RADIUS client (e.g. a WIFI AP) that generated the interim-update. The interim-updates with the updated information are sent to the RADIUS server as scheduled.
track-authentication
Syntax
track-authentication [accept]
no track-authentication
Context
config>router>radius-proxy>server>cache
config>service>vprn>radius-proxy>server>cache
Description
This command specifies if RADIUS authentication (from the AP) should be tracked in order to update the ESM host with the RADIUS client (for example, WIFI AP) on UE mobility. It also specifies the authentication packet from RADIUS client (for example, a WIFI AP) that the router should track for mobility.
The no form of this command stops tracking authentication for UE mobility.
Default
Not enabled
Parameters
accept
Indicates access-accept is tracked for mobility.
track-delete-hold-time
Syntax
track-delete-hold-time seconds
no track-delete-hold-time
Context
config>router>radius-proxy>server>cache
Description
This command specifies the delete hold-time in case the DHCP host gets a trigger to delete from the matched RADIUS Proxy server.
Default
0
Parameters
seconds
Spcifies the delete hold time, in seconds.
Values
 
LUDB Matching of RADIUS Proxy Cache Commands
local-user-db
Syntax
local-user-db local-user-db-name [create]
no local-user-db local-user-db-name
Context
config>subscr-mgmt
Description
This command enables the context to configure a local user database.
Default
not enabled
Parameters
local-user-db-name
Specifies the name of a local user database.
dhcp
Syntax
dhcp
Context
config>subscr-mgmt>loc-user-db
Description
This command configures DHCP host parameters.
host
Syntax
host
Context
config>subscr-mgmt>loc-user-db
Description
This command enables the context to configure DHCP host parameters.
match-radius-proxy-cache
Syntax
match-radius-proxy-cache
Context
config>subscr-mgmt>loc-user-db>dhcp>host
Description
This command enables the context to configure match-radius-proxy-cache parameters.
fail-action
Syntax
fail-action {continue|drop}
no fail-action
Context
config>subscr-mgmt>loc-user-db>dhcp>host>match-radprox-cache
Description
This command specifies the router’s action when failed to find matched radius-proxy-server cache entry.
The no form of the command reverts to the default.
Default
drop
Parameters
continue
Specifies that the will proceed with ESM authentication without dropping the DHCP packet.
drop
Specifies that the router will drop the DHCP packet.
mac-format
Syntax
mac-format format
no mac-format
Context
config>subscr-mgmt>loc-user-db>dhcp>host>match-radprox-cache
Description
This command specifies the format of MAC address used for matching incoming DHCP DISCOVER against the RADIUS proxy cache.
The no form of the command reverts to the default.
Default
mac-format "aa:"
Parameters
format
Specifies the format string that specifies the format of MAC address.
Values
match
Syntax
match {circuit-id|mac|remote-id}
match option [1..254]
no match
Context
config>subscr-mgmt>loc-user-db>dhcp>host>match-radprox-cache
Description
This command specifies the field/option of DHCP packet that is used to match against the radius-proxy-server cache.
The no form of the command reverts to the default.
Default
mac
Parameters
circuit-id
Specifies to match the circuit-id in DHCP option82
remote-id
Specifies to match the remote-id in DHCP option82
mac
Specifies to match the MAC address of DHCP client
option
Specifies to use specified DHCP option , 1 — 254
server
Syntax
server [service service-id] name server-name
no server
Context
config>subscr-mgmt>loc-user-db>dhcp>host>match-radprox-cache
Description
This command specifies the name of radius-proxy-server and optionally id of the service that the radius-proxy-server resides in.
The no form of the command removes the parameters from the configuration.
Default
no server
Parameters
service service-id
Specifies the ID or name of the service.
Values
name server-name
Specifies the name of radius-proxy-server up to 32 characters in length.
 
WLAN-GW-Group Commands
wlan-gw-group
Syntax
wlan-gw-group group-id [create]
no wlan-gw-group group-id
Context
config>isa
Description
This command creates a WLAN GW group. Note that the wlan-gw-group ID shares the same number space with the nat-group.
The no form of the command removes the group
Default
none
Parameters
group-id
Specifies WLAN Gateway Integrated Service Adaptor (ISA) Groups.
Values
active-iom-limit
Syntax
active-iom-limit number
no active-iom-limit
Context
config>isa>wlan-gw-group
Description
This command specifies the number of WLAN-GW IOMs used as active IOMs from the total number of configured WLAN-GW IOMs. If there are more configured IOM than active-iom-limit, then the remaining number of IOMs will be designated as backup(s).
The no form of the command removes the number from the configuration.
Parameters
number
Specifies the number of IOM's in this WLAN Gateway ISA group that are intended for active use.
Values
distributed-sub-mgmt
Syntax
[no] distributed-sub-mgmt
Context
config>isa>wlan-gw-group
Description
This command configures the WLAN gateway distributed subscriber management.
isa-aa-group
Syntax
isa-aa-group aa-group-id
no isa-aa-group
Context
config>isa>wlan-gw-group>distributed-sub-mgmt
Description
This command configures an ISA application assurance group for WLAN gateway DSM subscribers.
iom
Syntax
iom slot-number
no iom
Context
config>isa>wlan-gw-group
Description
This command designates the specified IOM as a WLAN-GW IOM. Each WLAN-GW IOM MUST be configured with two MS-ISA modules.
The no form of the command removes the number from the configuration.
Default
none
Parameters
slot-number
Indicates the IOM slot of the MDA associated with this member.
Values
nat
Syntax
nat
Context
config>isa>wlan-gw-group
Description
This command enables the context to configure NAT parameters under wlan-gw-group.
radius-accounting-policy
Syntax
radius-accounting-policy nat-accounting-policy
no radius-accounting-policy
Context
config>isa>wlan-gw-group>nat
Description
This command configures the RADIUS accounting policy to use for each MDA in this ISA group.
The no form of the command removes the accounting policy from the configuration.
Default
none
Parameters
nat-accounting-policy
Specifies the RADIUS accounting policy up to 32 characters in length.
session-limits
Syntax
session-limits
Context
config>isa>wlan-gw-group>nat
Description
This command configures the ISA NAT group session limits.
reserved
Syntax
reserved num-sessions
no reserved
Context
config>isa>nat>session-limits
Description
This command configures the number of sessions per block that will be reserved for prioritized sessions.
Parameters
num-sessions
Specifies the number of sessions reserved for prioritized sessions.
Values
watermarks
Syntax
watermarks high percentage low percentage
no watermarks
Context
config>isa>nat>session-limits
Description
This command configures the ISA NAT group watermarks.
high percentage
Specifies the high watermark of the number of sessions for each MDA in this NAT ISA group.
Values
low percentage
Specifies the low watermark of the number of sessions for each MDA in this NAT ISA group.
Values
Port Policy Commands
port-policy
Syntax
port-policy port-policy-name [create]
no port-policy port-policy-name
Context
config
Description
This command either creates a new port-policy with create parameter or enters the configuration context of an existing port-policy.
Default
none
Parameters
port-policy-name
Specifies the name of port-policy.
create
Keyword used to create a port-policy.
egress-scheduler-policy
Syntax
egress-scheduler-policy port-sched-plcy
egress-scheduler-policy
Context
config>port-policy
Description
This command specifies the port-scheduler-policy to use in the egress direction for the internal port connecting the WLAN-GW IOM to the MS-ISA.
Default
none
Parameters
port-sched-plcy
Specifies the name of the port-scheduler-policy up to 32 characters in length.
 
WLAN-GW Group Interface Commands
Note that the wlan-gw commands apply only to the 7750 SR platform.
group-interface
Syntax
group-interface ip-int-name [create]
group-interface ip-int-name [create] lns
group-interface ip-int-name [create] wlangw
no group-interface ip-int-name [create]
Context
config>service>ies>subscriber-interface
config>service>vprn>subscriber-interface
Description
This command creates a group interface. This interface is designed for triple-play services where multiple SAPs are part of the same subnet. A group interface may contain one or more SAPs.
Use the no form of the command to remove the group interface from the subscriber interface.
Default
no group interfaces configured
Parameters
ip-int-name
Specifies the interface name of a group interface. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
lns
Specifies to use LNS.
wlangw
Specifies the group interface for wlan-gw.
ip-mtu
Syntax
ip-mtu octets
no ip-mtu
Context
config>service>ies>subscriber-interface
config>service>vprn>subscriber-interface
Description
This command specifies the maximum size of frames on this group-interface. Packets larger than this will get fragmented.
The no form of the command removes this functionality.
Default
none
Parameters
octets
Specifies the largest frame size (in octets) that this interface can handle.
Values
wlan-gw
Syntax
wlan-gw
Context
config>service>ies>subscriber-interface>group-interface
config>service>vprn>subscriber-interface> group-interface
Description
This command enables the context to configure wlan-gw parameters.
Default
none
egress
Syntax
egress
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
Description
This command enables the context to configure egress QoS parameters for wlan-gw tunnels.
agg-rate-limit
Syntax
agg-rate-limit kilobits-per-second
no agg-rate-limit
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress
config>service>vprn>subscriber-interface>group-interface>wlan-gw>egress
Description
This command is used to control an HQoS aggregate rate limit. It is used in conjunction with the following parameter commands: rate, limit-unused-bandwidth, and queue-frame-based-accounting.
Parameters
kilobits-per-second
Specifies the aggregate rate limit.
Values
rate
Syntax
rate {max | rate}
no rate
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress>agg-rate
config>service>vprn>subscriber-interface>group-interface>wlan-gw>egress>agg-rate
Description
This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object (SAP, subscriber, Vport, etc.).
limit-unused-bandwidth
Syntax
[no] limit-unused-bandwidth
Context
config>service>ies>interface>sap>egress>agg-rate
config>service>ies>subscriber-interface> group-interface>sap>egress>agg-rate
config>service>vprn>interface>sap>egress>agg-rate
config>service>vprn>subscriber-interface> group-interface>sap>egress>agg-rate
Description
This command is used to enable (or disable) aggregate rate overrun protection on the agg-rate context.
queue-frame-based-accounting
Syntax
[no] queue-frame-based-accounting
Context
config>service>ies>interface>sap>egress>agg-rate
config>service>ies>subscriber-interface> group-interface>sap>egress>agg-rate
config>service>vprn>interface>sap>egress>agg-rate
config>service>vprn>subscriber-interface> group-interface>sap>egress>agg-rate
Description
This command is used to enabled (or disable) frame based accounting on all queues associated with the agg-rate context. Only supported on Ethernet ports. Not supported on HSMDA Ethernet ports.
hold-time
Syntax
hold-time infinite
hold-time [1..86400]
no hold-time
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress
config>service>vprn>subscriber-interface> group-interface>wlan-gw>egress
Description
This command configures the time for which egress shaping resources associated with a wlan-gw tunnel are held after the last subscriber on a tunnel is deleted.
Parameters
1..86400
Specifies the time, in seconds, for which shaping resources are held in seconds after last subscriber is deleted.
Values
qos
Syntax
qos policy-id
no qos
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress
Description
This command configures the identifier of the egress QoS policy associated with each wlan-gw tunnel of this interface.
The no form of the command removes the policy ID from the configuration.
Default
1
Parameters
policy-id
Specifies to apply the specified sap-egress-policy-id.
Values
scheduler-policy
Syntax
scheduler-policy scheduler-policy-name
no scheduler-policy
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress
Description
This command configures the identifier of the egress scheduler policy associated with each wlan-gw tunnel of this interface.
The no form of the command removes the scheduler policy name from the configuration.
Default
none
Parameters
scheduler-policy-name
Specifies the identifier of the egress scheduler policy associated with each wlan-gw tunnel of this interface
shape-multi-client-only
Syntax
[no] shape-multi-client-only
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress
Description
This command enables the egress shaping is only enabled for a wlan-gw tunnel while there are multiple UE (User Equipment) using it.
The no form of the command disables the egress shaping.
shaping
Syntax
shaping {per-retailer|per-tunnel}
no shaping
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>egress
Description
This command configures the the granularity of the egress shaping for wlan-gw on this group interface.
The no form of the command removes the parameter from the configuration.
Parameters
per-tunnel
Specifies that a separate shaper is applied to each wlan-gw tunnel.
per-retailer
Specifies that a separate shaper is applied to each retailer Mobile Network Operator's fraction of the wlan-gw tunnel payload.
gw-address
Syntax
gw-address ip-address
no gw-address
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command specifies gateway endpoint address for the wlan-gw tunnel.
The no form of the command removes the value from the wlan-gw configuration.
Default
none
Parameters
ip-address
Specifies the IP address of the wlan-gw tunnels on this group interface.
gw-ipv6-address
Syntax
gw-ipv6-address ipv6-address
no gw-ipv6-address
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command specifies a gateway IPv6 endpoint address for the wlan-gw tunnel.
The no form of the command removes the IPv6 the gateway IPv6 endpoint address for the wlan-gw tunnel.
Default
none
Parameters
ipv6-address
Specifies the gateway IPv6 endpoint address
Values
l2-access-points
Syntax
l2-access-points
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command enables the context to configure Layer 2 Access Points in WLAN Gateway Group-Interfaces.
l2-ap
Syntax
l2-ap sap-id [create]
no l2-ap sap-id
Context
config>service>vprn>sub-if>grp-if>wlan-gw>l2-access-points
config>service>ies >sub-if>grp-if>wlan-gw>l2-access-points
Description
This command adds a specific SAP where Layer-2 WLAN-GW aggregation will be performed. The following SAPs are supported.
This command can be repeated multiple times to create multiple Layer-2 access points.
The no form of the command removes the Layer-2 access point. This is only allowed if the l2-ap SAP is shutdown.
Default
No SAPs are defined
Parameters
sap-id
Specifies SAP to be created. For the exact syntax, see the common CLI command description of the 7750 Services Guide.
create
Keyword used to create the Layer-2 WLAN-GW aggregation instance. The create keyword requirement can be enabled/disabled in the environment>create context.
encap-type
Syntax
encap-type {default|null|dot1q|qinq}
no encap-type
Context
config>service>vprn>sub-if>grp-if>wlan-gw>l2-access-points>l2-ap
config>service>ies >sub-if>grp-if>wlan-gw>l2-access-points>l2-ap
Description
If different from default, this command overrides the value specified by l2-ap-encap-type on wlan-gw level. See the description of l2-ap-encap-type for more detail. This value can only be changed while the l2-ap is shutdown.
The no form of the command sets the default value.
Default
default
Parameters
default
Specifies to use the value specified by l2-ap-encap-type.
null
Specifies to use both the SAP and the AP are not VLAN-tagged.
dot1q
Specifies to use either the AP or the SAP uses one VLAN tag.
qinq
Up to two VLAN tags are used by the AP or SAP.
epipe-sap-template
Syntax
epipe-sap-template name
no epipe-sap-template
Context
config>service>vprn>sub-if>grp-if>wlan-gw>l2-access-points>l2-ap
config>service>ies >sub-if>grp-if>wlan-gw>l2-access-points>l2-ap
Description
This command specifies which SAP parameter template should be applied to the l2-ap SAP. This can only be changed when the l2-ap is shutdown.
The no form of the command removes the template, the SAP will use default parameters.
Default
none
Parameters
name
Specifies the name of the template to use.
shutdown
Syntax
shutdown sap-id [create]
no shutdown sap-id
Context
config>service>vprn>sub-if>grp-if>wlan-gw>l2-access-points>l2-ap
config>service>ies >sub-if>grp-if>wlan-gw>l2-access-points>l2-ap
Description
This command administratively enables this SAP to begin accepting Layer 2 packets for WIFI offloading.
The no form of the command disables this SAP.
Default
shutdown
l2-ap-encap-type
Syntax
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies >sub-if>grp-if>wlan-gw
Description
This parameter specifies the number of AP identifying VLAN tags for an AP. This is the default value that can be overridden per SAP. This value should at least be equal to the number of VLANs configured in the SAP or enabling a SAP will fail.
A SAP VLAN is explicitly configured, for example l2-ap 1/1/1:25. Other VLANs on the same port can still be used in other contexts.
The number of VLAN tags Epiped to WLAN-GW IOM equal the l2-ap-encap-type minus the encaps of the SAP. Upon receipt of a packet these VLANs will be stored as a Layer 2 tunnel identifier, and are only used in context of WLAN-GW.
The no form of the command sets the default value.
Default
null
Parameters
null
Both the SAP and the AP are not VLAN-tagged.
dot1q
Either the AP or the SAP uses one VLAN tag.
qinq
Up to two VLAN tags are used by the AP or SAP.
mobility
Syntax
mobility
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command enables the context to configure mobility parameters.
arp-ap
Syntax
arp-ap
no arp-ap
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>mobility
config>service>vprn>subscriber-interface> group-interface>wlan-gw>mobility
Description
This command enables the generation of an ARP packet on wlan-gw tunnel to learn the MAC address of the new AP when UE mobility is detected. The IP address in the ARP packet is the wlan-gw tunnel endpoint IP address of the AP.
The no form of the command disables sending of special ARP packet on wlan-gw tunnel to learn the MAC address of the AP when UE mobility is detected.
Default
not enabled
hold-time
Syntax
hold-time time in s
no hold-time
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>mobility
config>service>vprn>subscriber-interface> group-interface>wlan-gw>mobility
Description
This command configures the minimum time that a User Equipment will be held associated with its current Access Point (AP) before being associated with a new AP.
The hold time is used to prevent overwhelming the system with mobility triggers, by limiting the rate at which a UE can move from one AP to another while the system is very busy already.
Default
no default
Parameters
time in s
Specifies a hold-down time, in seconds, for handling of successive mobility triggers for a UE. It is the minimal time a UE stays associated with an AP.
Values
trigger
Syntax
trigger [data] [iapp]
no trigger
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>mobility
config>service>vprn>subscriber-interface> group-interface>wlan-gw>mobility
Description
This command specifies the type of packet used as a mobility trigger.
Ths no form of the command removes the parameters from the configuration and disables data-plane mobility.
Parameters
data
Specifies that data traffic be used as a trigger.
iapp
Specifies that Inter Access Point Protocol (IAPP) messages be used as a trigger.
multi-tunnel-type
Syntax
[no] multi-tunnel-type
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command enables terminating multiple types of tunnels.
The no form of the command disables terminating multiple types of tunnels.
oper-down-on-group-degrade
Syntax
[no] oper-down-on-group-degrade
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command operationally brings down the WLAN-GW group if the total number of operational WLAN-GW IOMs in the WLAN-GW group fall below the configured number of active WLAN-GW IOMs. This triggers withdrawal of the route to tunnel endpoint and subscriber subnets in routing.
Default
none
router
Syntax
router router-instance
no router
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command specifies the routing instance that wlan-gw gateway endpoint resides in.
The no form of the command removes the value from the wlan-gw configuration.
Default
none
Parameters
router-instance
Specifies the identifier of the virtual router instance where the tunneled User Equipment traffic is routed.
tcp-mss-adjust
Syntax
tcp-mss-adjust segment-size
no tcp-mss-adjust
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command configures the TCP Maximum Segment Size (MSS) adjustment for the wlan-gw gateway.
The no form of the command disables adjusting tcp-mss values.
Default
none
Parameters
segment-size
Specifies the value to put into the TCP Maximum Segment Size (MSS) option if not already present, or if the present value is higher.
Values
tunnel-encaps
Syntax
tunnel-encaps
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command enables the context to configure tunnel encapsulation parameters.
learn-l2tp-cookie
Syntax
learn-l2tp-cookie {if-match|never|always} [cookie hex string]
no learn-l2tp-cookie
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command specifies when this system will learn the cookie from L2TP tunnels terminating on this interface. Learning the cookie means that the value of the octets 3-8 of the cookie is interpreted as an access point’s MAC address, and used as such, for example in the Called-Station-Id attribute of RADIUS Interim-Update messages.
Parameters
if-match
Specifies that the cookie will be interpreted only if the value of the first two octets of the cookie is equal to the value of the object tmnxWlanGwSoftGreIfL2tpCookie.
cookie hex string
Only valid if if-match is used. Specifies the value used to compare the first two bytes of the cookie. Specified in HEX format, possible range [0x0000 .. 0xFFFF]
Values
never
Specifies that the cookie value will always be ignored.
always
Always learn the AP-MAC from the cookie, no matter what the value of the first two bytes is.
vlan-tag-ranges
Syntax
vlan-tag-ranges
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command enables the context to configure vlan-to-retail-map parameters to map dot1Q tags to retail-service-id. The WIFI AP could insert a dot1Q tag in the Layer 2 frame within the GRE tunnel to indicate the retail service provider for the subscriber.
Default
none
default-retail-svc-id
Syntax
default-retail-svc-id service-id
no default-retail-svc-id
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>vlan-tag-ranges
config>service>vprn>subscriber-interface> group-interface>wlan-gw>vlan-tag-ranges
Description
This command specifies the id of default retail service if there is no match found in VLAN to retail map configuration (specified by the vlan command). For DSM and migrant, this command is only applicable for non-NAT stacks.
Default
none
Parameters
service-id
specifies the identifier of the retail service to be used by default of a value in the retail service map of this interface.
Values
retail-svc-id
Syntax
retail-svc-id service-id
no retail-svc-id
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
Description
This command configures the retailer service.
Parameters
service-id
specifies the identifier of the retail service.
Values
router-advertisements
Syntax
[no] router-advertisements
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range
Description
This command configures IPv6 router advertisements for this group-interface.
current-hop-limit
Syntax
[no] current-hop-limit limit
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>router-advertisements
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>router-advertisements
Description
This command configures the hop-limit advertised for this group-interface.
Default
64
Parameters
limit
Specifies the default value to be placed in the current hop limit field in router advertisements sent from this interface.
Values
vlan
Syntax
vlan start [0..4095] end [0..4095] retail-svc-id service-id
no vlan start [0..4095] end [0..4095]
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>retailer
config>service>vprn>subscriber-interface> group-interface>wlan-gw>retailer
Description
This command creates a mapping from a range of VLANs (appearing in the wlan-gw encapsulated Layer 2 frame) to a retail service ID.
The no form of the command removes the parameters from the configuration.
Default
none
Parameters
start [0..4095]
Specifies the start VLAN tag of this range.
Values
end [0..4095]
Specifies the end VLAN tag of this range.
Values
retail-svc-id service-id
Specifies the identifier of the retail service to be used by default of a value in the retail service map of this interface.
Values
wlan-gw-group
Syntax
wlan-gw-group group-id
no wlan-gw-group
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command specifies the id of wlan-gw-group that the wlan-gw gateway binds to.
The no form of the command removes the value from the wlan-gw configuration.
Default
none
Parameters
group-id
Specifies the ISA WLAN-GW group.
Values
pool-manager
Syntax
pool-manager
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw
config>service>vprn>subscriber-interface> group-interface>wlan-gw
Description
This command enables the context to configure pool manager data for a WLAN GW subscriber interface.
dhcpv6-client
Syntax
dhcpv6-client
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>pool-manager
config>service>vprn>subscriber-interface> group-interface>wlan-gw>pool-manager
Description
This command configures the DHCPv6 client for the pool manager.
ia-na
Syntax
ia-na
Context
config>service>ies>subscriber-interface>group-interface>wlan-gw>pool-manager
config>service>vprn>subscriber-interface> group-interface>wlan-gw>pool-manager
Description
This command configures the DHCPv6 client for the pool manager.
link-addr
Syntax
link-addr ipv6-address
no link-addr
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>slaac
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>slaac
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>ia-na
config>service>ies >sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>ia-na
Description
This command specifies the ipv6-address that should be included in the link-address field of the relay header. This can be used for pool-selection by the DHCPv6 server.
The no form of this command falls back to the default.
Default
0::0
Parameters
ipv6-address
Specifies the IPv6 address up to 32 characters.
pool-name
Syntax
pool-name name
no pool-name
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>slaac
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>slaac
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>ia-na
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt>ia-na
Description
This command specifies the pool name that should be sent in the DHCPv6 messages. This will be reflected in the Alcatel-Lucent vendor specific pool option (vendor-id 6527, option-id 0x02).
The no form of this command removes pool-name and the option will not be sent in DHCPv6.
Parameters
name
Specifies the pool name up with 32 characters.
lease-query
Syntax
lease-query [max-retry Max nbr of retries]
no lease-query
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
Description
This command enables lease-query. If this is specified the dhcpv6-client will retrieve any existing addresses when becoming active. The lease-query is performed for all of the configured servers
The no form of this command disables lease-query.
Parameters
max-retry
Specifies the maximum number of retries before the lease query assumes no existing subnets were allocated.
Values
server
Syntax
server ipv6-address [ipv6-address...(upto 8 max)]
no server [ipv6-address [ipv6-address...(upto 8 max)]]
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
Description
This specifies the DHCPv6 servers that are used for requesting addresses. Up to 8 servers can be used simultaneously.
The no form of this command removes the server. This cannot be executed while any dhcpv6 client application is not shutdown.
Default
none
Parameters
ipv6-address
Specifies the unicast IPv6 address of a DHCPv6 server.
slaac
Syntax
slaac
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
config>service>ies>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
Description
This command configures SLAAC for the DHCPv6 client.
source-ip
Syntax
source-ip ipv6-address
no source-ip
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
config>service>ies >sub-if>wlan-gw>pool-mgr>dhcpv6-clnt
Description
This command specifies the source-ip to be used by the DHCPv6 client.
The no form of this command removes the specific source-ip. In this case the DHCPv6 client will fall back to the IP address configured on the outgoing interface.
Parameters
ipv6-address
Specifies the IPv6 address up to 32 characters.
watermarks
Syntax
watermarks high high-percentage low low-percentage
no watermarks
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr
config>service>ies>sub-if>wlan-gw>pool-mgr
Description
This command configures the watermarks used to determine if a new prefix should be allocated or an old prefix should be removed. A new prefix will be allocated when the total usage level for the ISA reaches the high watermark. A prefix will be freed if no addresses are currently in use and the usage level without this prefix would be below the low watermark.
The no form of this command resets the watermarks to its default values of 95% high and 90% low.
Default
watermarks high 95 low 90
Parameters
high high-percentage
Specifies the high watermark.
Values
low low-percentage
Specifies the low watermark. The value must be lower than the high percentage value.
Values
wlan-gw-group
Syntax
wlan-gw-group nat-group-id
no wlan-gw-group
Context
config>service>vprn>sub-if>wlan-gw>pool-mgr
config>service>ies>sub-if>wlan-gw>pool-mgr
Description
This command specifies the ISA WLAN Gateway group.
Default
none
Parameters
nat-group-id
Specifies the identifier of the WLAN Gateway group.
Values
redundancy
Syntax
redundancy
Context
config>service>ies>subscriber-interface>wlan-gw
Description
This command enables the context to configure WLAN-GW redundancy-related parameters.
Default
none
export
Syntax
export ip-prefix/length
no export
Context
config>service>ies>subscriber-interface>wlan-gw>redundancy
Description
This command specifies an IPv4 route (prefix/length) per subscriber-interface to be exported (announced) to indicate liveness of the subscriber-interface on the WLAN-GW. This route is the one that is monitored in routing by the peer WLAN-GW to decide its state with respect.
Default
none
Parameters
ip-prefix/length
Specifies the IP prefix and length.
Values
monitor
Syntax
monitor ip-prefix/length
no monitor
Context
config>service>ies>subscriber-interface>wlan-gw>redundancy
Description
This command specifies an IPv4 route (prefix/length) per subscriber-interface to be monitored in the FIB to determine liveness of the subscriber-interface (and consequently all associated group-interfaces of type wlangw) on a peer WLAN-GW. This route is the one that is advertised in routing by the peer WLAN-GW when the subscriber-interface and WLAN-GW group are operationally up
Default
none
Parameters
ip-prefix/length
Specifies the IP prefix and length.
Values
 
Migrant User Support Commands
http-redirect-policy
Syntax
http-redirect-policy policy-name
no http-redirect-policy
Context
config>subscr-mgmt
Description
This command configures the redirect policy to constrain forwarding of an unauthenticated “migrant” WIFI user.
Default
none
Parameters
policy-name
Specifies the HTTP redirect policy name up to 32 characters in length.
forward-entries
Syntax
forward-entries
Context
config>subscr-mgmt>http-rdr-plcy
Description
Enters the context to configure entries that need to be forwarded
Default
none
dst-port
Syntax
dst-port tcp-port
no dst-port
Context
config>subscr-mgmt>http-rdr-plcy
Description
This command specifies the port to match the destination port in the HTTP request.
HTTP traffic that does not match this port, is not redirected.
Default
80
Parameters
tcp-port
Specifies the TCP port.
Values
dst-ip
Syntax
dst-ip ip-address protocol ip-protocol dst-port port-number
dst-ip ip-address protocol ip-protocol dst-port port-number prefix-length prefix-length
no dst-ip ip-address protocol ip-protocol dst-port port-number
Context
config>subscr-mgmt>http-rdr-plcy
Description
This command configures traffic flow to be forwarded via match in the redirect policy.
Default
none
Parameters
ip-address
Specifies the IPv4 or IPv6 address to match the destination address in the IP header of the traffic received from the subscriber.
prefix-length
Specifies the length of the prefix specified by the ip-address.
Values
protocol ip-protocol
Specifies the protocol to match the IP protocol in the IP header of the traffic received from the subscriber.
Values
dst-port port-number
Specifies the port to match the destination port in the HTTP request.
Values
portal-hold-time
Syntax
portal-hold-time seconds
no portal-hold-time
Context
config>subscr-mgmt>http-rdr-plcy
Description
This command configures the time for which the forwarding state applicable during redirect phase is held in the system, after the user has been authenticated on the portal. This allows the http response from the portal to be forwarded back on the existing connection.
none
Parameters
seconds
Specifies how long the system holds on to re-direct forwarding resources of a subscriber, after it has left the re-direct portal.
Values
url
Syntax
url rdr-url-sting
no url
Context
config>subscr-mgmt>http-rdr-plcy
Description
This command configures the HTTP URL to re-direct the matching traffic to. It also can specify inclusion of original URL, MAC address and IP address of the subscriber in the redirect URL.
none
Parameters
rdr-url-sting
Specifies the URL to redirect to.
Values
rdr-url-string [255 chars max]
macro substitutions:
$URL Request-URI in the HTTP GET Request received
$MAC string that represents the MAC address of the subscriber host
$IP a string that represents the IP address of the subscriber host
wlan-gw
Syntax
wlan-gw
Context
config>service>vprn>sub-if>grp-if
config>service>ies>sub-if>grp-if
Description
This command enables the context to configure wlan-gw parameters.
vlan-tag-ranges
Syntax
vlan-tag-ranges
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
Description
This command enters the context for per vlan range configuration.
Default
none
default-retail-svc-id
Syntax
default-retail-svc-id service-id
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges
config>service>ies>sub-if>grp-if>wlan-gw>ranges
Description
This command configures the default retailer service for WIFI users.
Default
none
range
Syntax
range start [0..4096] end [0..4096]
range default
no range start [0..4096] end [0..4096]
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges
config>service>ies>sub-if>grp-if>wlan-gw>ranges
Description
This command creates or enters the context of specified VLAN range for configuration applicable to that range of VLANs.
Default
none
Parameters
start [0..4096]
Specifies the start of the vlan range.
end [0..4096]
Specifies the end of vlan the range.
default
Configures defaults for the interface.
distributed-sub-mgmt
Syntax
distributed-sub-mgmt
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
This command enables the context to configure distributed-sub-mgmt configuration per vlan-range. This also includes vlan-range default, which makes this configuration applicable to the wlan-gw group-interface.
Default
none
accounting-policy
Syntax
accounting-policy policy-name
no accounting-policy
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
This command specifies the isa-radius-policy used for accounting messages originated from the ISAs in the wlan-gw group. The policy can specify up to five accounting servers and configuration-specific to these accounting servers. It also specifies configuration specific to RADIUS client on ISAs and RADIUS attributes to be included in accounting messages.
Default
none
Parameters
policy-name
Specifies the name of the account policy up to 32 characters in length.
accounting-update-interval
Syntax
accounting-update-interval [5..259200]
no accounting-update-interval
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
This command enables the interim accounting and specifies the interim accounting interval.
Default
none
Parameters
5..259200
Specifies the interim accounting interval in seconds.
def-app-profile
Syntax
def-app-profile profile-name
no def-app-profile
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
This command configures the default application profile.
dsm-ip-filter
Syntax
dsm-ip-filter dsm-ip-filter-name
no dsm-ip-filter
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
This command configures an IP filter that is distributed on ISA cards.
This command specifies the IP filter applied to all UEs corresponding to default vlan-range (such as a group-interface) or the specified vlan-range. The IP filter can be created in the subscr-mgmt>wlan-gw>distributed-sub-mgmt context, and can contain up to 1024 match entries. The IP filter can be overridden per UE from RADIUS via access-accept or COA.
Default
none
Parameters
dsm-ip-filter-name
Specifies the identifier of the distributed-sub-mgmt IP filter.
egress-policer
Syntax
egress-policer [256 chars max]
no egress-policer
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
This command specifies the egress policer applied to all UEs corresponding to default vlan-range (such as, group-interface) or the specified vlan-range. The policer can be created in the subscr-mgmt>wlan-gw>distributed-sub-mgmt context. The egress policer can be overridden per UE from RADIUS via access-accept or COA.
Default
none
Parameters
256 chars max
Specifies the identifier of the distributed-sub-mgmt policer for egress traffic.
ingress-policer
Syntax
ingress-policer policer-name
no ingress-policer
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
.This command specifies the ingress policer applied to all UEs corresponding to default vlan-range (such as group-interface) or the specified vlan-range. The policer can be created in the subscr-mgmt>wlan-gw>distributed-sub-mgmt context. The ingress policer can be overridden per UE from RADIUS via access-accept or COA.
Default
none
Parameters
policer-name
Specifies the identifier of the distributed-sub-mgmt policer for ingress traffic.
one-time-redirect
Syntax
one-time-redirect url rdr-url-string port port-num
no one-time-redirect
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>distrib-sub-mgmt
Description
This command enables one-time http-redirect to specified redirect URL for traffic matching the specified destination port.
Default
none
Parameters
url rdr-url-string
Specifies the HTTP web address that will be sent to the user’s browser.
port port-num
Specifies the destination port number as a decimal hex or binary.
Values
dhcp
Syntax
dhcp
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges
config>service>ies>sub-if>grp-if>wlan-gw>ranges
Description
Enters the context to create DHCP configuration for WLAN-GW ISA subscribers (e.g. migrant subscribers).
Default
none
dhcp6
Syntax
dhcp6
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges
config>service>ies>sub-if>grp-if>wlan-gw>ranges
Description
Enters the context to create DHCP6 configuration for WLAN-GW ISA subscribers.
Default
none
active-preferred-lifetime
Syntax
active-preferred-lifetime [hrs hours] [min minutes] [sec seconds]
no active-preferred-lifetime
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
Description
This command specifies the signaled preferred lifetime in DHCPv6 or SLAAC after full authentication. This is only applicable to DSM.
Default
min 10
Parameters
hrs hours
Specifies the number of active preferred lifetime hours.
Values
min minutes
Specifies the number of active preferred lifetime minutes.
Values
sec seconds
Specifies the number of active preferred lifetime seconds.
Values
Combined values: min 5 – hrs 1
active-valid-lifetime
Syntax
active-valid-lifetime [hrs hours] [min minutes] [sec seconds]
no active-valid-lifetime
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
Description
This command specifies the signaled valid lifetime in DHCPv6 or SLAAC after full authentication. This is only applicable to DSM.
Default
min 10
Parameters
hrs hours
Specifies the number of active-valid-lifetime hours.
Values
min minutes
Specifies the number of active-valid-lifetime minutes.
Values
sec seconds
Specifies the number of active-valid-lifetime seconds.
Values
active-lease-time
Syntax
active-lease-time [hrs hours] [min minutes] [sec seconds]
no active-lease-time
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the lease time for an authenticated user.
Default
none
Parameters
hrs hours
Specifies the number of initial lease time hours.
Values
min minutes
Specifies the number of initial lease time minutes.
Values
sec seconds
Specifies the number of initial lease time seconds.
Values
initial-preferred-lifetime
Syntax
initial-preferred-lifetime [hrs hours] [min minutes] [sec seconds]
no initial-preferred-lifetime
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
Description
This command specifies the signaled preferred lifetime in DHCPv6 or SLAAC after full authentication (DSM and/or ESM).
Default
min 10
Parameters
hrs hours
Specifies the number of initial preferred lifetime hours.
Values
min minutes
Specifies the number of initial preferred lifetime minutes.
Values
sec seconds
Specifies the number of initial preferred lifetime seconds.
Values
Combined values: min 5 – hrs 1
initial-valid-lifetime
Syntax
initial-valid-lifetime [hrs hours] [min minutes] [sec seconds]
no initial-valid-lifetime
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>dhcp6
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
config>service>ies>sub-if>grp-if>wlan-gw>vlan-ranges>range>slaac
Description
This command specifies the signaled preferred lifetime in DHCPv6 or SLAAC during a migrant phase.
Default
min 5
Parameters
hrs hours
Specifies the number of initial preferred lifetime hours.
Values
min minutes
Specifies the number of initial preferred lifetime minutes.
Values
sec seconds
Specifies the number of initial preferred lifetime seconds.
Values
Combined values: min 5 – hrs 1
initial-lease-time
Syntax
initial-lease-time [hrs hours] [min minutes] [sec seconds]
no initial-lease-time
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the lease time for a user which is migrant (unauthenticated).
Default
none
Parameters
hrs hours
Specifies the number of initial lease time hours.
Values
min minutes
Specifies the number of initial lease time minutes.
Values
sec seconds
Specifies the number of initial lease time Biteme#24ds.
Values
l2-aware-ip-address
Syntax
l2-aware-ip-address ip-address
no l2-aware-ip-address
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the l2-aware NAT inside IP address to be assigned via DHCP on WLAN-GW ISA.
Default
none
Parameters
ip-address
Specifies the l2-aware NAT inside IP address.
primary-dns
Syntax
primary-dns ip-address
no primary-dns
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the primary DNS address to be returned via DHCP on WLAN-GW ISA.
Default
none
Parameters
ip-address
Specifies the primary DNS address
secondary-dns
Syntax
secondary-dns ip-address
no secondary-dns
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the secondary DNS address to be returned via DHCP on WLAN-GW ISA.
Default
none
Parameters
ip-address
Specifies the secondary DNS address.
primary-nbns
Syntax
primary-nbns ip-address
no primary-nbns
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the primary NBNS address to be returned via DHCP on WLAN-GW ISA.
Default
none
Parameters
ip-address
Specifies the primary NBNS address.
secondary-nbns
Syntax
secondary-nbns ip-address
no secondary-nbns
Context
config>service>vprn>sub-if>grp-if>wlan-gw>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>dhcp
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>dhcp
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>dhcp
Description
This command configures the secondary NBNS address to be returned via DHCP on WLAN-GW ISA.
Default
none
Parameters
ip-address
Specifies the secondary NBNS address.
idle-timeout
Syntax
idle-timeout action idle-timeout-action
no idle-timeout
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range
config>service>ies >sub-if>grp-if>wlan-gw>vlan-ranges>range
Description
This command specifies idle-timeout behavior for DSM UEs and UEs undergoing (ISA-based) portal authentication. This knob only specifies the desired action, idle-timeout is activated by RADIUS on a per-UE basis.
The no form of the command resets the idle-timeout to its default
Default
idle-timeout action remove
Parameters
action
Specifies which action to perform when the idle-timeout timer goes off.
Values
http-redirect-policy
Syntax
http-redirect-policy policy-name
no http-redirect-policy
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
This command specifies http redirect policy on ISA to redirect http traffic to the URL specified in the policy.
Default
none
Parameters
policy-name
Specifies the name of the http redirect policy under subscriber-management context.
l2-service
Syntax
l2-service service-id
no l2-service
Context
config>service>vprn>sub-if>grp-if>wlan-gw>vlan-ranges>range
config>service>ies >sub-if>grp-if>wlan-gw>vlan-ranges>range
Description
This command specifies the VPLS service used for L2 wholesale. When such a service is configured no other configuration is allowed under the vlan-range.
The no form of the command removes the L2 wholesale service, this is only allowed if the l2-service node is shutdown.
Parameters
service-id
Specifies the VPLS service ID to use for Layer 2 wholesale.
nat-policy
Syntax
nat-policy policy-name
no nat-policy
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
This command specifies the NAT policy for WLAN-GW ISA subscribers.
Default
none
authentication
Syntax
authentication
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
Enters the context to create configuration for authenticating a user from the WLAN-GW ISA.
Default
none
authenticate-on-dhcp
Syntax
[no] authenticate-on-dhcp
Context
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
This command enables initial authentication (when there is no state for the UE on the ISA), to be triggered by DHCP DISCOVER or REQUEST. The default behavior s authentication based on first Layer 3 packet.
Default
none
authentication-policy
Syntax
authentication-policy policy-name
no authentication-policy
Context
config>service>vprn>sub-if>grp-if>wlan-gw>authentication
config>service>ies>sub-if>grp-if>wlan-gw>authentication
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>authentication
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>authentication
Description
This command specifies authentication policy configured under aaa context for authenticating users on WLAN-GW ISA.
Default
none
Parameters
policy-name
Specifies the name of the authentication policy up to 32 characters in length.
hold-time
Syntax
hold-time [hrs hours] [min minutes] [sec seconds]
no hold-time
Context
config>service>vprn>sub-if>grp-if>wlan-gw>authentication
config>service>ies>sub-if>grp-if>wlan-gw>authentication
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>authentication
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>authentication
Description
This command configures the minimum time that a user is held down after a failed authentication attempt.
Default
.none
Parameters
hrs hours
the minimum time that a user is held down in hours.
Values
min minutes
the minimum time that a user is held down in minutes
Values
sec seconds
the minimum time that a user is held down in seconds.
Values
data-triggered-ue-creation
Syntax
[no] data-triggered-ue-creation
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
This command enables or disables data-triggered subscriber creation for WIFI subscribers. Data triggered UE creation is currently only supported for UDP and TCP packets.
Default
none
track-mobility
Syntax
track-mobility
Context
config>service>vprn>sub-if>grp-if>wlan-gw
config>service>ies>sub-if>grp-if>wlan-gw
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range
Description
This command enters the context to configure RADIUS-proxy cache information required for subscribers that are created via “data-triggered” authentication. The RADIUS proxy cache enables efficient handling of UE mobility.
none
mac-format
Syntax
mac-format mac-format
no mac-format
Context
config>service>vprn>sub-if>grp-if>wlan-gw>track-mobility
config>service>ies>sub-if>grp-if>wlan-gw>track-mobility
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>track-mobility
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>track-mobility
Description
This command configures how the MAC address is represented by the RADIUS proxy server.
Default
none
Parameters
mac-format
Specifies how the MAC address is represented by the RADIUS proxy server
Values
radius-proxy-cache
Syntax
radius-proxy-cache router router-instance server server-name
no radius-proxy-cache
Context
config>service>vprn>sub-if>grp-if>wlan-gw>track-mobility
config>service>ies>sub-if>grp-if>wlan-gw>track-mobility
config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>track-mobility
config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>track-mobility
Description
This command specifies the RADIUS-proxy server to allow subscribers created via data-triggered authentication to create an entry. This RADIUS proxy cache entry allows efficient handling of UE mobility.
Default
none
Parameters
router router-instance
Specifies the router instance.
Values
server server-name
Specifies the server name up to 32 characters in length.
 
sap-template
Syntax
sap-template sap template
no sap-template
Context
config>service>vpls>wlan-gw
Description
This command specifies the vpls-sap-template that will be applied on the internal SAPs created for communication between the VPLS and the ISAs.
The no form of the command removes the SAP template.
Parameters
sap-template
Specifies the SAP template to apply. The template is a vpls-sap-template created in the service>template context.
 
Distributed Subscriber Management Commands
dsm-ip-filter
Syntax
dsm-ip-filter name [create]
no dsm-ip-filter name
Context
config>subscr-mgmt>wlan-gw>dsm
Description
This command configures a set of filter rules that can be applied to a DSM UE.
The no form of this command can only be executed if no entries are configured under this filter.
Parameters
filter-name
Specifies the name of the filter as it will be referred to in other contexts.
create
Keyword used to create a dsm-ip-filter name. The create keyword requirement can be enabled/disabled in the environment>create context.
default-action
Syntax
default-action {drop|forward}
no default-action
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6
Description
The default action specifies what should happen to packets that do not match any of the configured entries.
The no form of this command reverts to the default.
Default
default-action drop
Parameters
drop
Drops the packet.
forward
Forwards the packet.
entry
Syntax
entry entry-id [create]
no entry entry-id
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6
Description
This command configures a new entry for this filter. When processing a packet, entries are matched in order, starting with the lowest entry-id. A maximum of 128 IPv4 and 128 IPv6 DSM filter entries are allowed box-wide.
The no form of this command reverts to the default.
Parameters
entry-id
Specifies the id of this filter entry.
action
Syntax
action {drop|forward|none}
no action
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>entry
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6>entry
Description
The action specifies what should happen to packets that do match this entry. If the configured action is none, this entry is not applied and processing will continue to match against subsequent entries.
The no form of this command reverts to the default.
Default
action none
Parameters
drop
Drops the packet.
forward
Forwards the packet.
none
Disables this entry. Packet processing continues with the next entry.
match
Syntax
match protocol {any|icmp|tcp|udp|gre}
no match
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>entry
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>ipv6>entry
Description
This command creates a match context for this entry. The protocol specifies which Layer-4 protocol the packet should match.
The no form of this command removes the match context of this entry.
Default
no match
Parameters
any
Matches any protocol.
icmp
Matches ICMP packets in a v4 filter.
tcp
Matches TCP packets.
udp
Matches UDP packets.
gre
Matches GRE over IP packets.
dst-ip
Syntax
dst-ip ip-prefix/length
no dst-ip
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>entry
Description
This command specifies that the packet’s destination IP address must match the specified IP prefix + mask.
The no form of this command disables the match on destination IP.
Default
no dst-ip
Parameters
ip-prefix/length
Specifies the IP prefix to match on.
dst-port
Syntax
dst-port operator port-number
no dst-port
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-ip-filter>entry
Description
This command specifies that the packet’s destination IP address must match the specified IP prefix + mask.
The no form of this command disables the match on destination IP.
Default
no dst-ip
Parameters
ip-prefix/length
Specifies the IP prefix to match on.
dsm-policer
Syntax
dsm-policer policer-name [type policer-type] [create]
no dsm-policer policer-name
Context
config>subscr-mgmt>wlan-gw>dsm
Description
This command creates a policer profile that can be applied to a DSM host. When creating a profile the first time, both the create and type parameters are required.
The WLAN-GW allows configuration of both single-rate and dual-rate bucket policers.
The no form of this command removes the profile.
Parameters
policer-name
The name by which this policer will be referenced.
type policer-type
Specifies the policer type. The dual-bucket-bandwidth policer applies both a CIR and PIR.
Values
action
Syntax
action {permit-deny|priority-mark}
no action
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies what should happen with packets that are in-profile and out-of-profile.
The no value of this command reverts to its default.
Default
action permit-deny
Parameters
permit-deny
Drop all packets that are out of profile (do not conform to the PIR).
priority-mark
Currently not supported, the policer will take no action.
adaptation-rule
Syntax
adaptation-rule pir adaptation-rule [cir {adaptation-rule}]
no adaptation-rule
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
For operational efficiency the operational rate of a policer cannot take on every value in the configurable range. This configuration defines rule has to be followed when mapping a configured rate to an operational rate.
The cir adaptation-rule can only be set on dual-bucket-bandwidth policers.
The no form of this command reverts to its default.
Context
adaptation-rule pir closest cir closest
Parameters
min
The operational rate must minimally be the configured rate. The first operational value bigger or equal to the configured rate will be chosen.
max
The operational rate may maximally be the configured rate. The first operational value smaller or equal to the configured rate will be chosen.
closest
Chooses the operational value closest to the configured value, lower or higher
cbs
Syntax
cbs burst-size
no cbs
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies the committed burst-size value of this policer. This can only be set on dual-bucket-bandwidth policers.
The no form of this command reverts to its default.
Default
cbs 0
Parameters
burst-size
The committed burst-size in kilobytes.
Values
 
mbs
Syntax
mbs burst-size
no mbs
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies the maximum burst-size value of this policer.
The no form of this command reverts to its default.
Default
mbs 0
Parameters
burst-size
The maximum burst-size in kilobytes.
Values
rate
Syntax
rate rate [cir rate]
no rate
Context
config>subscr-mgmt>wlan-gw>dsm>dsm-policer
Description
This command specifies at which rate the policer drains packets. The cir value is only supported on dual-bucket-bandwidth policers. If rate max is configured, no actual rate limitations are applied.
The no form of this command reverts to the default.
Default
rate max
Parameters
rate
Specifies the rate in Kbps.
Values
 
Show Commands
acct-on-off-group
Syntax
acct-on-off-group [group-name]
Context
show>aaa
Description
This command displays Acct-On-Off group information and the associated RADIUS server policies
Parameters
group-name
Displays information pertaining to the specified acct-on-off group.
 
Sample Output
# show aaa acct-on-off-group "group-1" 
===============================================================================
Acct-On-Off-Group Information
===============================================================================
acct on off group name               : group-1
  - controlling Radius-Server-policy :  
        aaa-server-policy-3
  - monitored by Radius-Server-policy :  
        aaa-server-policy-4
-------------------------------------------------------------------------------
Nbr of Acct-on-off-groups displayed : 1
-------------------------------------------------------------------------------
===============================================================================
 
radius-proxy-server
Syntax
radius-proxy-server server-name
radius-proxy-server server-name cache
radius-proxy-server server-name cache hex-key hex-string
radius-proxy-server server-name cache string-key string
radius-proxy-server server-name cache summary
radius-proxy-server server-name statistics
radius-proxy-server
Context
show>router
Description
This command displays summary of RADIUS-proxy cache or specific entries.
Parameters
server-name
Displays information about the specified server name.
cache
Displays messages used to generate the key for the cache of this RADIUS proxy server.
hex-key hex-string
Displays information about the specified hex string.
Values
string-key string
Displays information about the specified string.
summary
Displays a summary of the cache of the RADIUS proxy servers.
statistics
Displays statistics about the RADIUS proxy servers of this system.
 
Displays the RADIUS attribute type to cache for this RADIUS proxy server. Refer to RFC 2865, Remote Authentication Dial In User Service (RADIUS), Section 5 Attributes.
Displays the RADIUS Vendor-Id. Refer to RFC 2865, Remote Authentication Dial In User Service (RADIUS), Section 5.25 Vendor-Specific.
Sample Output
system# show router 10 radius-proxy-server "myProxyServer1" 
===============================================================================
RADIUS Proxy server "myProxyServer1"
===============================================================================
Description                 : myDesc
Purpose                     : authentication 
Administrative state        : in-service
Default acct server policy  : myRadiusServerPolicy1
Default auth server policy  : myRadiusServerPolicy2
Send accounting response    : true
Last management change      : 02/17/2012 14:54:28
-------------------------------------------------------------------------------
Cache settings
-------------------------------------------------------------------------------
Administrative state        : enabled
Key packet type             : access-accept
Key attribute type          : 12
Key vendor ID               : (Not Specified)
Timeout (s)                 : 60
Track accounting            : stop interim-update accounting-on accounting-off 
Load balance key            : source-ip-udp
===============================================================================
Interfaces
-------------------------------------------------------------------------------
myInterface1                     
myInterface2                     
myInterface3                     
-------------------------------------------------------------------------------
No. of Interface(s): 3
===============================================================================
Usernames/RADIUS server policies
===============================================================================
Id Username-match                     RADIUS-server-policy             Purpose
------------------------------------------------------------------------------------
1.  aaa                                myRadiusServerPolicy2 		auth
==============================================================================
system# 
wlan-gw
Syntax
wlan-gw
Context
show>router
Description
This command displays Wireless LAN Gateway information.
isa-subnets
Syntax
isa-subnets [detail]
isa-subnets [detail] interface interface-name
isa-subnets prefix ipv6-address/prefix-length
Context
show>router>wlan-gw
Description
This command outputs all the prefixes in use by the wlan-gw pool-manager.
Parameters
detail
Displays detailed information for each prefix.
interface interface-name
Displays only the prefixes associated with this subscriber-interface.
ipv6-address/prefix-length
Displays details of a specific ipv6 address and prefix.
Sample Output
system# show router wlan-gw isa-subnets
===============================================================================
ISA Subnets
===============================================================================
Prefix                                                   MDA     Family  Usage
-------------------------------------------------------------------------------
2001:db8::/48                                            3/1     dhcpv6  0%
2001:db8:1::/48                                          3/2     dhcpv6  0%
2001:db8:2::/48                                          4/1     dhcpv6  0%
2001:db8:3::/48                                          4/2     dhcpv6  0%
2001:db8:4::/48                                          5/1     dhcpv6  0%
2001:db8:5::/48                                          5/2     dhcpv6  0%
2001:db8:6::/48                                          3/1     slaac   0%
2001:db8:7::/48                                          3/2     slaac   0%
2001:db8:8::/48                                          4/1     slaac   0%
2001:db8:9::/48                                          4/2     slaac   0%
2001:db8:a::/48                                          5/1     slaac   0%
2001:db8:b::/48                                          5/2     slaac   0%
-------------------------------------------------------------------------------
No. of ISA subnets: 12
===============================================================================
 
*A:Dut-C# show router wlan-gw isa-subnets prefix 2001:db8::/48
===============================================================================
ISA Subnet Prefix           : 2001:db8::/48
-------------------------------------------------------------------------------
Group Id                    : 1
Member Id                   : 1
MDA                         : 3/1
Family                      : dhcpv6
Subscriber Interface        : wlangw-sub-itf
Pool Is Old                 : No
Usage Level                 : 0%
Remaining Lease Time        : 0d 23:50:54
DHCPv6 Options              : (length=512)
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                            : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
===============================================================================
 
mgw-address-cache
Syntax
mgw-address-cache [arec] [snaptr] [srv]
mgw-address-cache apn apn-domain-string
Context
show>router>wlan-gw
Description
This command displays the mobile gateway's DNS lookup address cache.
Parameters
arec
Displays A-records/
snaptr
Displays Straightforward-NAPTR information.
srv
Displays SRV records.
apn apn-domain-string
Specifies the APN (Access Point Name) of this DNS cache entry.
Sample Output
*A:Dut-C# show router 300 wlan-gw mgw-address-cache 
===============================================================================
Mobile Gateway SNAPTR cache
===============================================================================
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 10
Index                       : 1
-------------------------------------------------------------------------------
Preference                  : 10
Service                     : x-3gpp-pgw:x-gn-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Time left (s)               : 3582
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 20
Index                       : 2
-------------------------------------------------------------------------------
Preference                  : 20
Service                     : x-3gpp-pgw:x-s2a-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Time left (s)               : 3582
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 30
Index                       : 3
-------------------------------------------------------------------------------
Preference                  : 30
Service                     : x-3gpp-pgw:x-s2b-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
No. of SNAPTR cache entries: 3
===============================================================================
===============================================================================
Mobile Gateway SRV cache
===============================================================================
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Priority                    : 10      
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10      
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
Time left (s)               : 3581
-------------------------------------------------------------------------------
No. of SRV cache entries: 6
===============================================================================
===============================================================================
Mobile Gateway address cache
===============================================================================
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.23
Time left (s)               : 3581 
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.29
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.35
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.24
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.30
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.36
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.25
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.31
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.37
Time left (s)               : 3581
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.26
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.32
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.38
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.27
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.33
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.39
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.28
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.34
Time left (s)               : 3580
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.40
Time left (s)               : 3580
-------------------------------------------------------------------------------
No. of cache entries: 18
 
 
*A:Dut-C# show router 300 wlan-gw mgw-address-cache arec 
===============================================================================
Mobile Gateway address cache
===============================================================================
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.23
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.29
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.35
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.24
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.30
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.36
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.25
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.31
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.37
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.26
Time left (s)               : 3573
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.32
Time left (s)               : 3573
-----------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.38
Time left (s)               : 3572
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.27
Time left (s)               : 3572
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.33
Time left (s)               : 3572
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.39
Time left (s)               : 3572 
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.28
Time left (s)               : 3572
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.34
Time left (s)               : 3572
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.40
Time left (s)               : 3572
-------------------------------------------------------------------------------
No. of cache entries: 18
===============================================================================
 
 
*A:Dut-C# show router 300 wlan-gw mgw-address-cache srv  
===============================================================================
Mobile Gateway SRV cache
===============================================================================
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
Time left (s)               : 3567
 
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
Time left (s)               : 3567    
 
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
Time left (s)               : 3566
 
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
Time left (s)               : 3566
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
Time left (s)               : 3566
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
Time left (s)               : 3566
-------------------------------------------------------------------------------
No. of SRV cache entries: 6
===============================================================================
 
 
*A:Dut-C# show router 300 wlan-gw mgw-address-cache snaptr
===============================================================================
Mobile Gateway SNAPTR cache
===============================================================================
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 10
Index                       : 1
-------------------------------------------------------------------------------
Preference                  : 10
Service                     : x-3gpp-pgw:x-gn-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Time left (s)               : 3555
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 20
Index                       : 2
-------------------------------------------------------------------------------
Preference                  : 20
Service                     : x-3gpp-pgw:x-s2a-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Time left (s)               : 3555
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 30
Index                       : 3
-------------------------------------------------------------------------------
Preference                  : 30
Service                     : x-3gpp-pgw:x-s2b-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Time left (s)               : 3554
 
-------------------------------------------------------------------------------
No. of SNAPTR cache entries: 3
 
 
*A:Dut-C# show router 300 wlan-gw mgw-address-cache apn full.dotted.apn.apn.epc.mnc010.mcc206.3gppnetwork.org 
===============================================================================
Mobile Gateway APN Cache
===============================================================================
-------------------------------------------------------------------------------
APN > NAPTR
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 10
Index                       : 1
-------------------------------------------------------------------------------
Preference                  : 10
Service                     : x-3gpp-pgw:x-gn-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Time left (s)               : 3531
-------------------------------------------------------------------------------
APN > NAPTR > SRV
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
Time left (s)               : 3531
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.23
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.29
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.35
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.24
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.30
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv1.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.36
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 20
Index                       : 2       
-------------------------------------------------------------------------------
Preference                  : 20
Service                     : x-3gpp-pgw:x-s2a-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Time left (s)               : 3530
-------------------------------------------------------------------------------
APN > NAPTR > SRV
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.25
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.31
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.37
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.26
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.32
Time left (s)               : 3529
                                      
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv2.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.38
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.
                              3gppnetwork.org
Order                       : 30
Index                       : 3
-------------------------------------------------------------------------------
Preference                  : 30
Service                     : x-3gpp-pgw:x-s2b-gtp
Next lookup                 : dns-srv
Replacement                 : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Priority                    : 10
Index                       : 1
-------------------------------------------------------------------------------
Weight                      : 10
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.27
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.33
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a1.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.39
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.
                              3gppnetwork.org
Priority                    : 20
Index                       : 2
-------------------------------------------------------------------------------
Weight                      : 20
Port                        : 2123
Target                      : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A                 
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.28
Time left (s)               : 3529
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.34
Time left (s)               : 3528
-------------------------------------------------------------------------------
APN > NAPTR > SRV > A
-------------------------------------------------------------------------------
APN                         : full.dotted.apn.apn.epc.mnc010.mcc206.srv3.a2.
                              3gppnetwork.org
-------------------------------------------------------------------------------
Mobile Gateway address      : 9.0.0.40
Time left (s)               : 3528
-------------------------------------------------------------------------------
No. of cache entries: 18 
mgw-map
Syntax
mgw-map
Context
show>router>wlan-gw
Description
This command displays the Mobile Gateway map.
Sample Output
*A:Dut-C# show router 300 wlan-gw mgw-map                                                                     
===============================================================================
Mobile Gateway map
===============================================================================
Address prefix                                Profile
-------------------------------------------------------------------------------
9.0.0.29/32                                   Ivo
-------------------------------------------------------------------------------
No. of address prefixes: 1
 
mobile-gateway
Syntax
mobile-gateway [mgw-profile profile-name] [local-address ip-address] [control protocol] [interface-type interface-type]
mobile-gateway remote-address ip-address [udp-port port]
mobile-gateway remote-address ip-address [udp-port port] statistics
Context
show>router>wlan-gw
Description
This command displays Mobile Gateway information.
Parameters
mgw-profile profile-name
Specifies the name that identifies the profile.
local-address ip-address
 
Values
control protocol
Specifies the control plane protocol used for the connection with this Mobile Gateway.
Values
interface-type interface-type
Specifies the interface type of the connection between WLAN Gateway and Mobile Gateway.
Values
remote-address ip-address
 
Values
udp-port port
Specifies the UDP port.
Values
statistics
Displays statistics information about the Mobile Gateways connected to this system.
Sample Output
*A:Dut-C# show router 300 wlan-gw mobile-gateway mgw-profile "Ivo" 
===============================================================================
Mobile gateways
===============================================================================
Remote address              : 9.0.0.29
UDP port                    : 2123
-------------------------------------------------------------------------------
State                       : up
Local address               : 5.1.45.3
Profile                     : Ivo
Control protocol            : gtpv1-c
Interface type              : gn
Restart count               : 1
Time                        : 2014/03/24 15:38:53
-------------------------------------------------------------------------------
No. of Mobile gateways: 1
 
 
*A:Dut-C# show router 300 wlan-gw mobile-gateway local-address 5.1.45.3 
===============================================================================
Mobile gateways
===============================================================================
Remote address              : 9.0.0.29
UDP port                    : 2123
-------------------------------------------------------------------------------
State                       : up
Local address               : 5.1.45.3
Profile                     : Ivo
Control protocol            : gtpv1-c
Interface type              : gn
Restart count               : 1
Time                        : 2014/03/24 15:38:53
 
-------------------------------------------------------------------------------
No. of Mobile gateways: 1
 
 
*A:Dut-C# show router 300 wlan-gw mobile-gateway control gtpv1-c        
===============================================================================
Mobile gateways
===============================================================================
Remote address              : 9.0.0.29
UDP port                    : 2123
-------------------------------------------------------------------------------
State                       : up
Local address               : 5.1.45.3
Profile                     : Ivo
Control protocol            : gtpv1-c
Interface type              : gn
Restart count               : 1
Time                        : 2014/03/24 15:38:53
 
-------------------------------------------------------------------------------
No. of Mobile gateways: 1
 
 
 
 
 
*A:Dut-C# show router 300 wlan-gw mobile-gateway interface-type gn 
===============================================================================
Mobile gateways
===============================================================================
Remote address              : 9.0.0.29
UDP port                    : 2123
-------------------------------------------------------------------------------
State                       : up
Local address               : 5.1.45.3
Profile                     : Ivo
Control protocol            : gtpv1-c
Interface type              : gn
Restart count               : 1
Time                        : 2014/03/24 15:38:53
 
-------------------------------------------------------------------------------
No. of Mobile gateways: 1
 
 
*A:Dut-C# show router 300 wlan-gw mobile-gateway remote-address 9.0.0.29 
===============================================================================
Mobile gateway
===============================================================================
Remote address              : 9.0.0.29
UDP port                    : 2123
-------------------------------------------------------------------------------
State                       : up
Local address               : 5.1.45.3
Profile                     : Ivo
Control protocol            : gtpv1-c
Interface type              : gn
Restart count               : 1
Time                        : 2014/03/24 15:38:53
 
 
*A:Dut-C# show router 300 wlan-gw mobile-gateway remote-address 9.0.0.29 udp-port 2123 
===============================================================================
Mobile gateway
===============================================================================
Remote address              : 9.0.0.29
UDP port                    : 2123
-------------------------------------------------------------------------------
State                       : up
Local address               : 5.1.45.3
Profile                     : Ivo
Control protocol            : gtpv1-c
Interface type              : gn
Restart count               : 1
Time                        : 2014/03/24 15:38:53
 
 
*A:Dut-C# show router 300 wlan-gw mobile-gateway remote-address 9.0.0.29 udp-port 2123 statistics 
===============================================================================
Mobile gateway statistics
===============================================================================
tx echo requests                                        : 4
tx echo responses                                       : 0
rx echo requests                                        : 0
rx echo responses                                       : 4
rx version not supported                                : 0
rx malformed pkts                                       : 0
rx unknown pkts                                         : 0
rx missing IE pkts                                      : 0
peer restarts                                           : 0
peer restart counter                                    : 1
path mgmt failures                                      : 0
create PDP requests                                     : 1
create PDP responses                                    : 1
delete PDP requests                                     : 0
delete PDP responses                                    : 0
modify PDP requests                                     : 0
modify PDP responses                                    : 0
 
soft-gre-tunnel-qos
Syntax
soft-gre-tunnel-qos [detail]
soft-gre-tunnel-qos remote-ip ip-address [local-ip ip-address] [detail]
Context
show>router>wlan-gw
Description
This command displays soft-GRE tunnel-QoS resource information.
Parameters
remote-address ip-address
Specifies the IP address of the Mobile Gateway,that is the source IP address in the tunnel header of received packets.
Values
local-address ip-address
Specifies the IP address of this system,that is the destination IP address in the tunnel header of received packets.
Values
detail
Displays detailed information.
Sample Output
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnel-qos 
===============================================================================
Soft GRE tunnel QoS
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnel-qos detail 
===============================================================================
Soft GRE tunnel QoS
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
Service Access Points(SAP)
===============================================================================
Service Id         : 2147483650               
SAP                : 5/1/lo-gre:1             Encap             : q-tag
Description        : Internal SAP
Admin State        : Up                       Oper State        : Up
Flags              : None
Multi Svc Site     : None                     
Last Status Change : 03/24/2014 15:03:48      
Last Mgmt Change   : 03/24/2014 15:14:00      
 
-------------------------------------------------------------------------------
Encap Group Specifics
-------------------------------------------------------------------------------
Encap Group Name   : _tmnx_SHAPER_GR000       Group Type        : ISID
Qos-per-member     : TRUE                     
Members            :
1                                     
 
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
E. qos-policy      : 1                        Q Frame-Based Acct: Disabled
E. Sched Policy    :                          E. Agg-limit      : -1
                                              Limit Unused BW   : Disabled
-------------------------------------------------------------------------------
Encap Group Member 1 Base Statistics
-------------------------------------------------------------------------------
Last Cleared Time     : N/A
 
Forwarding Engine Stats
                        Packets                 Octets
 
For. InProf           : 0                       0
For. OutProf          : 0                       0
Dro. InProf           : 0                       0
Dro. OutProf          : 0                       0
 
-------------------------------------------------------------------------------
Encap Group Member 1 Queue Statistics
-------------------------------------------------------------------------------
 
                        Packets                 Octets
 
Egress Queue 1                        
For. InProf           : 0                       0
For. OutProf          : 0                       0
Dro. InProf           : 0                       0
Dro. OutProf          : 0                       0
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnel-qos remote-ip 201.0.0.2 
===============================================================================
Soft GRE tunnel QoS
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnel-qos  remote-ip 201.0.0.2  local-ip 50.1.1.1 
===============================================================================
Soft GRE tunnel QoS
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnel-qos  remote-ip 201.0.0.2  local-ip 50.1.1.1 detail 
===============================================================================
Soft GRE tunnel QoS
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
Service Access Points(SAP)
===============================================================================
Service Id         : 2147483650               
SAP                : 5/1/lo-gre:1             Encap             : q-tag
Description        : Internal SAP
Admin State        : Up                       Oper State        : Up
Flags              : None
Multi Svc Site     : None                     
Last Status Change : 03/24/2014 15:03:48      
Last Mgmt Change   : 03/24/2014 15:14:00      
 
-------------------------------------------------------------------------------
Encap Group Specifics
-------------------------------------------------------------------------------
Encap Group Name   : _tmnx_SHAPER_GR000       Group Type        : ISID
Qos-per-member     : TRUE                     
Members            :
1                                     
                                      
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
E. qos-policy      : 1                        Q Frame-Based Acct: Disabled
E. Sched Policy    :                          E. Agg-limit      : -1
                                              Limit Unused BW   : Disabled
-------------------------------------------------------------------------------
Encap Group Member 1 Base Statistics
-------------------------------------------------------------------------------
Last Cleared Time     : N/A
 
Forwarding Engine Stats
                        Packets                 Octets
 
For. InProf           : 0                       0
For. OutProf          : 0                       0
Dro. InProf           : 0                       0
Dro. OutProf          : 0                       0
 
-------------------------------------------------------------------------------
Encap Group Member 1 Queue Statistics
-------------------------------------------------------------------------------
 
                        Packets                 Octets
 
Egress Queue 1
For. InProf           : 0                       0
For. OutProf          : 0                       0
Dro. InProf           : 0                       0
Dro. OutProf          : 0                       0
 
soft-gre-tunnels
Syntax
soft-gre-tunnels local-ip ip-address remote-ip ip-address ue
soft-gre-tunnels [local-ip ip-address] [remote-ip ip-address] [isa-group wlan-gw-group-id] [member [1..255]] [summary] [detail]
Context
show>router>wlan-gw
Description
This command displays soft-GRE tunnel-QoS resource information.
Parameters
remote-address ip-address
Specifies the IP address of the Mobile Gateway,that is the source IP address in the tunnel header of received packets.
Values
local-address ip-address
Specifies the IP address of this system,that is the destination IP address in the tunnel header of received packets.
Values
ue
Displays information for the specified user equipment.
isa-group wlan-gw-group-id
Specifies the identifier of the WLAN Gateway ISA group that terminates GRE for this group interface.
Values
member [1..255]
Specfies the identifier of this WLAN Gateway ISA Group member.
summary
Displays a summary of the specified parameters.
detail
Displays detailed information.
Sample Output
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels                                                   
===============================================================================
Soft GRE tunnels
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
ISA group ID                : 1
ISA group member ID         : 5
Time established            : 2014/03/24 15:38:52
Number of UE                : 1
Access Point MAC            : 00:00:00:00:00:01
AP MAC learn failed         : false
 
Tunnel QoS
----------
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
-------------------------------------------------------------------------------
No. of tunnels: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 
===============================================================================
Soft GRE tunnels
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
ISA group ID                : 1
ISA group member ID         : 5
Time established            : 2014/03/24 15:38:52
Number of UE                : 1
Access Point MAC            : 00:00:00:00:00:01
AP MAC learn failed         : false
 
Tunnel QoS
----------
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
-------------------------------------------------------------------------------
No. of tunnels: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 remote-ip 201.0.0.2 
===============================================================================
Soft GRE tunnels
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
ISA group ID                : 1
ISA group member ID         : 5
Time established            : 2014/03/24 15:38:52
Number of UE                : 1
Access Point MAC            : 00:00:00:00:00:01
AP MAC learn failed         : false
 
Tunnel QoS
----------
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
-------------------------------------------------------------------------------
No. of tunnels: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 remote-ip 201.0.0.2 ue 
===============================================================================
Tunnel User Equipments
===============================================================================
MAC address                 : 00:02:00:00:00:01
-------------------------------------------------------------------------------
VLAN Q-tag                  : 1
MPLS label                  : (Not Specified)
Tunnel router               : 50
Tunnel remote IP address    : 201.0.0.2
Tunnel local IP address     : 50.1.1.1
Retail service              : N/A
SSID                        : "1"
Previous Access Point IP    : (Not Specified)
IMSI                        : 206100000000001
MGW router                  : 300
Mobile Gateway              : 9.0.0.29
APN                         : full.dotted.apn.mnc010.mcc206.gprs
Last move time              : 2014/03/24 15:38:52
-------------------------------------------------------------------------------
No. of UE: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 remote-ip 201.0.0.2 isa-group 1 
===============================================================================
Soft GRE tunnels
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
ISA group ID                : 1
ISA group member ID         : 5
Time established            : 2014/03/24 15:38:52
Number of UE                : 1
Access Point MAC            : 00:00:00:00:00:01
AP MAC learn failed         : false
 
Tunnel QoS
----------
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
-------------------------------------------------------------------------------
No. of tunnels: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 remote-ip 201.0.0.2 isa-group 1 member 5 
===============================================================================
Soft GRE tunnels
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
ISA group ID                : 1
ISA group member ID         : 5
Time established            : 2014/03/24 15:38:52
Number of UE                : 1
Access Point MAC            : 00:00:00:00:00:01
AP MAC learn failed         : false
 
Tunnel QoS
----------
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
 
-------------------------------------------------------------------------------
No. of tunnels: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 remote-ip 201.0.0.2 isa-group 1 member 5 summary 
===============================================================================
Soft GRE tunnels summary
===============================================================================
Remote IP address - Local IP address
-------------------------------------------------------------------------------
201.0.0.2 - 50.1.1.1
-------------------------------------------------------------------------------
No. of tunnels: 1
 
 
*A:Dut-C# show router 50 wlan-gw soft-gre-tunnels local-ip 50.1.1.1 remote-ip 201.0.0.2 isa-group 1 member 5 detail  
===============================================================================
Soft GRE tunnels
===============================================================================
Remote IP address           : 201.0.0.2
Local IP address            : 50.1.1.1
ISA group ID                : 1
ISA group member ID         : 5
Time established            : 2014/03/24 15:38:52
Number of UE                : 1
Access Point MAC            : 00:00:00:00:00:01
AP MAC learn failed         : false
 
Tunnel QoS
----------
Operational state           : active
Number of UE                : 1
Remaining hold time (s)     : N/A
Service Access Points(SAP)
===============================================================================
Service Id         : 2147483650               
SAP                : 5/1/lo-gre:1             Encap             : q-tag
Description        : Internal SAP
Admin State        : Up                       Oper State        : Up
Flags              : None
Multi Svc Site     : None                     
Last Status Change : 03/24/2014 15:03:48      
Last Mgmt Change   : 03/24/2014 15:14:00      
-------------------------------------------------------------------------------
Encap Group Specifics
-------------------------------------------------------------------------------
Encap Group Name   : _tmnx_SHAPER_GR000       Group Type        : ISID
Qos-per-member     : TRUE                     
Members            :
1
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
E. qos-policy      : 1                        Q Frame-Based Acct: Disabled
E. Sched Policy    :                          E. Agg-limit      : -1
                                              Limit Unused BW   : Disabled
-------------------------------------------------------------------------------
Encap Group Member 1 Base Statistics
-------------------------------------------------------------------------------
Last Cleared Time     : N/A
 
Forwarding Engine Stats
                        Packets                 Octets
 
For. InProf           : 0                       0
For. OutProf          : 0                       0
Dro. InProf           : 0                       0
Dro. OutProf          : 0                       0
-------------------------------------------------------------------------------
Encap Group Member 1 Queue Statistics
-------------------------------------------------------------------------------
Packets                 Octets
 
Egress Queue 1
For. InProf           : 0                       0
For. OutProf          : 0                       0
Dro. InProf           : 0                       0
Dro. OutProf          : 0                       0
===============================================================================
-------------------------------------------------------------------------------
No. of tunnels: 1
 
tunnels
Syntax
tunnels [local-ipip-address] [remote-ip ip-address] [isa-group wlan-gw-group-id] [member [1..255]] [summary] [detail]
tunnels local-ip ip-address remote-ip ip-address ue
Context
show>router>wlan-gw
Description
This command displays tunnel operation information.
Parameters
local-address ip-address
Specifies the IP address of this system,that is the destination IP address in the tunnel header of received packets.
Values
remote-address ip-address
Specifies the IP address of the Mobile Gateway,that is the source IP address in the tunnel header of received packets.
Values
isa-group wlan-gw-group-id
Specifies the identifier of the WLAN Gateway ISA group that terminates GRE for this group interface.
Values
member [1..255]
Specfies the identifier of this WLAN Gateway ISA Group member.
summary
Displays a summary of the specified parameters.
detail
Displays detailed information.
ue
Displays information for the specified user equipment.
Sample Output
Note that the remote/local IP addresses are locally generated for VLAN tunnels.
show router 50 wlan-gw tunnels
===============================================================================
Access Point tunnels
===============================================================================
Remote IP address : fe80::3e8f:ffff:fe00:1901
Local IP address : fe80::ff:fe02:202
ISA group ID : 1
ISA group member ID : 4
Time established : 2015/01/07 17:42:01
Number of UE : 1
Access Point MAC : 00:00:00:00:00:05
AP MAC learn failed : false
Encapsulation : vlan
VLAN tag 1                  : 1000
VLAN tag 2                  : (None)
-------------------------------------------------------------------------------
No. of tunnels: 1
===============================================================================
 
 
radius-server-policy
Syntax
radius-server-policy policy-name [acct-on-off]
radius-server-policy policy-name associations
radius-server-policy policy-name msg-buffer-stats
radius-server-policy policy-name statistics
radius-server-policy [acct-on-off]
Context
show>aaa
Description
This command displays RADIUS server policy information.
Parameters
policy-name
Displays information pertaining to the specified policy name.
associations
Displays the association between the RADIUS server policy and the applications referencing the policy (RADIUS proxy, route downloader, authentication policy, accounting policy, dynamic services policy).
statistics
Displays statistics of the RADIUS server policy and RADIUS servers referenced in the policy.
acct-on-off
Displays the acct-on-off operational state for the RADIUS server policy.
msg-buffer-stats
– Displays statistics for the RADIUS message buffering.
Sample Output
show aaa radius-server-policy "aaa-server-policy-1" 
===============================================================================
RADIUS server policy "aaa-server-policy-1"
===============================================================================
Description                 : Radius AAA server policy
Acct Request script policy  : (Not Specified)
Auth Request script policy  : (Not Specified)
Accept script policy        : script-policy-1
Acct-On-Off                 : Enabled (state Not Blocked)
-------------------------------------------------------------------------------
RADIUS server settings
-------------------------------------------------------------------------------
Router                      : "Base"
Source address              : (Not Specified)
Access algorithm            : direct
Retry                       : 3
Timeout (s)                 : 5
Hold down time (s)          : 30
Last management change      : 02/20/2013 13:32:05
===============================================================================
===============================================================================
Servers for "aaa-server-policy-1"
===============================================================================
Idx Name                             Address         Port        Oper State
                                                     Auth/Acct   
-------------------------------------------------------------------------------
1   server-1                         172.16.1.1      1812/1813   in-service
===============================================================================
 
 
 
# show aaa radius-server-policy acct-on-off 
==============================================================================
RADIUS server policies AcctOnOff state
==============================================================================
Name                                    OperState      LastStateChange
------------------------------------------------------------------------------
aaa-server-policy-1                     on             02/20/2013 21:23:57
aaa-server-policy-2                     NotApplicable  NotApplicable
aaa-server-policy-3                     sendAcctOn     NotApplicable
aaa-server-policy-4                     off            02/20/2013 21:40:57
------------------------------------------------------------------------------
No. of policies: 4
==============================================================================
 
# show aaa radius-server-policy "aaa-server-policy-1" acct-on-off 
===============================================================================
RADIUS server policy "aaa-server-policy-1" AcctOnOff info
===============================================================================
Oper state                  : on
Session Id                  : 242FFF0000000451253EED
Last state change           : 02/20/2013 21:23:57
Trigger                     : startUp
Server                      : "server-1"
===============================================================================
 
 
show aaa radius-server-policy "aaa-server-policy-3" msg-buffer-stats                                   
===============================================================================
RADIUS server policy "aaa-server-policy-3" message buffering stats
===============================================================================
buffering acct-interim      : enabled
  min interval (s)          : 60
  max interval (s)          : 3600
  lifetime (hrs)            : 12
buffering acct-stop         : enabled
  min interval (s)          : 60
  max interval (s)          : 3600
  lifetime (hrs)            : 12
 
Statistics
-------------------------------------------------------------------------------
Total acct-stop messages in buffer                        : 6
Total acct-interim messages in buffer                     : 10
Total acct-stop messages dropped (lifetime expired)       : 0
Total acct-interim messages dropped (lifetime expired)    : 0
Last buffer clear time                                    : N/A
Last buffer statistics clear time                         : N/A
-------------------------------------------------------------------------------
===============================================================================
 
 
show aaa radius-server-policy "aaa-server-policy-1" statistics 
===============================================================================
RADIUS server policy "aaa-server-policy-1" statistics
===============================================================================
Tx transaction requests                         : 383
Rx transaction responses                        : 383
Transaction requests timed out                  : 0
Transaction requests send failed                : 0
Packet retries                                  : 0
Transaction requests send rejected              : 0
Authentication requests failed                  : 0
Accounting requests failed                      : 0
Ratio of access-reject over auth responses      : 0%
Transaction success ratio                       : 100%
Transaction failure ratio                       : 0%
Statistics last reset at                        : n/a
 
Server 1 "server-1" address 172.16.1.1 auth-port 1812 acct-port 1813
-------------------------------------------------------------------------------
Tx request packets                              : 383
Rx response packets                             : 383
Request packets timed out                       : 0
Request packets send failed                     : 0
Request packets send failed (overload)          : 0
Request packets waiting for reply               : 0
Response packets with invalid authenticator     : 0
Response packets with invalid msg authenticator : 0
Authentication packets failed                   : 0
Accounting packets failed                       : 0
Avg auth response delay (10 100 1K 10K) in ms   :   27.1   22.8   22.8   22.8
Avg acct response delay (10 100 1K 10K) in ms   :   6.24   12.5   11.5   11.5
Statistics last reset at                        : n/a
 
===============================================================================
 
 
show aaa radius-server-policy "myRadiusServerPolicy1" associations
===============================================================================
RADIUS Proxy Associations
===============================================================================
Router RADIUS Proxy Server Purpose Username
-------------------------------------------------------------------------------
Base myProxyServerBase acc (default)
vprn10 myProxyServer1 acc (default)
-------------------------------------------------------------------------------
No. of associations: 2
 
 
show aaa radius-server-policy "aaa-server-policy-1" associations 
===============================================================================
RADIUS Proxy Associations
===============================================================================
Router RADIUS Proxy Server Purpose Username
-------------------------------------------------------------------------------
Base   myProxyServerBase   acc     (default)
-------------------------------------------------------------------------------
No. of associations: 1
===============================================================================
No route downloader entries found.
===============================================================================
Authentication Policy Associations
===============================================================================
Authentication Policy
-------------------------------------------------------------------------------
auth-policy-1
-------------------------------------------------------------------------------
No. of associations: 1
===============================================================================
===============================================================================
Accounting Policy Associations
===============================================================================
Accounting Policy
-------------------------------------------------------------------------------
acct-policy-1
acct-policy-2
-------------------------------------------------------------------------------
No. of associations: 2
===============================================================================
No dynamic-services policy entries found.
wlan-gw-group
Syntax
wlan-gw-group wlan-gw-group-id
wlan-gw-group wlan-gw-group-id associations
wlan-gw-group wlan-gw-group-id member [1..255] [statistics]
wlan-gw-group
Context
show>isa
Description
This command displays WLAN-GW group information including wlan-gw tunnels.
Parameters
wlan-gw-group-id
Displays information about the specified wlan-gw-group-id.
associations
Displays information about association for the specified wlan-gw-group-id.
member [1..255]
Displays information about the WLAN-GW-specific status and basic statistics information about the specified member.
statistics
Displays statistics information about the members of the specified WLAN-GW group.
Sample Output
system# show isa wlan-gw-group 1
===============================================================================
WLAN Gateway group 1
===============================================================================
test
Administrative state        : in-service
Operational state           : in-service
Active IOM limit            : 2
Port policy                 : myPortPol
Last Mgmt Change            : 02/17/2012 14:54:27
-------------------------------------------------------------------------------
NAT specific information for ISA group 1
-------------------------------------------------------------------------------
Reserved sessions           : 10
High Watermark (%)          : 20
Low Watermark (%)           : 10
Accounting policy           : natAccPol
Last Mgmt Change            : 02/17/2012 15:01:31
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
ISA Group 1 members
===============================================================================
Group    Member     State          Mda     Addresses     Blocks     Se-%    Hi     Se-Prio
----------------------------------------------------------------------------------------------------------------------------------
         1                 1               active         3/1              0                  0          < 1      N         10
1                 2               active         3/2              0                  0          < 1      N         10
1                 3               active         4/1              0                  0          < 1      N         10
1                 4               active         4/2              0                  0          < 1      N         10
---------------------------------------------------------------------------------------------------------------------------------
No. of members: 4
===============================================================================
System# show isa wlan-gw-group 1 member 2 
===============================================================================
ISA WLAN Gateway Group 1 Member 2
===============================================================================
MDA                                                       : 3/2
Number of wlan-gw tunnels                                : 0
Number of UE                                              : 0
Number of activated Egress Encapsulation Group members    : 0
Number of pending Egress Encapsulation Group members      : 0
Number of tunnel QoS problems                             : 0
===============================================================================
 
gtp-session
Syntax
gtp-session imsi imsi apn apn-string | gtp-session [mgw-address ip-address] [mgw-router router-instance] [remote-control-teid teid] [local-control-teid teid] [detail]
gtp-session imsi imsi
gtp-statistics
Context
show>subscr-mgmt>wlan-gw
Description
This command displays GTP session information.
Parameters
imsi imsi
Specifies the IMSI (International Mobile Subscriber Identity) of this UE.
apn apn-string
Specifies the APN (Access Point Name).
mgw-address ip-address
Specifies the IP address of the Mobile Gateway, \that is the source IP address in the tunnel header of received packets.
mgw-router router-instance
Specifies the identifier of the virtual router instance where the GTP tunnel is terminated.
remote-control-teid teid
Specifies the remote control plane Tunnel Endpoint Identifier (TEID).
local-control-teid teid
Specifies the local control plane Tunnel Endpoint Identifier (TEID).
detail
Displays detailed information.
Sample Output
*A:Dut-C# show subscriber-mgmt wlan-gw gtp-session 
===============================================================================
GTP sessions
===============================================================================
IMSI                        : 206100000000001
APN                         : full.dotted.apn.mnc010.mcc206.gprs
-------------------------------------------------------------------------------
Mobile Gateway router       : 300
Mobile Gateway address      : 9.0.0.29
Remote control TEID         : 5678
Local control TEID          : 4289724672
Charging characteristics    : (None)
-------------------------------------------------------------------------------
No. of GTP sessions: 1
 
gtp-statistics
Syntax
gtp-statistics
Context
show>subscr-mgmt>wlan-gw
Description
This command displays GTP statistics.
mgw-profile
Syntax
mgw-profile profile-name
mgw-profile profile-name associations
mgw-profile
Context
show>subscr-mgmt>wlan-gw
Description
This command displays Mobile Gateway profile information.
ssid
Syntax
ssid
Context
show>subscr-mgmt>wlan-gw
Description
This command displays SSID information.
statistics
Syntax
statistics
Context
show>subscr-mgmt>wlan-gw
Description
This command displays statistics information.
ue
Syntax
ue [vlan qtag] [mpls-label label] [retail-svc-id service-id] [ssid service-set-id] [previous-access-point ip-address]
ue mac ieee-address
Context
show>subscr-mgmt>wlan-gw
Description
This command displays user equipment information.
Parameters
vlan qtag
Displays information about the VLAN Q-tag present in the traffic received from this UE.
Values
mpls-label label
Displays information about the MPLS label present in the traffic received from this UE.
retail-svc-id service-id
Displays information about the identifier of the specified retail service.
ssid service-set-id
Displays information about the Service Set ID (SSID) of this UE.
previous-access-point ip-address
Displays information about the IP address of the previous Access Point (AP) of this UE.
mac ieee-address
Displays information about the MAC address of this UE.
Values
Sample Output
System# show subscriber-mgmt wlan-gw ue
======================================================================
User Equipments
======================================================================
MAC address                 : 00:02:00:00:00:39
----------------------------------------------------------------------
VLAN Q-tag                  : 1
MPLS label                  : (Not Specified)
Tunnel router               : 50
Tunnel remote IP address    : 20C9::7:1:2
Tunnel local IP address     : 2032::1:1:7
Retail service              : N/A
SSID                        : 1
Previous Access Point IP    : (Not Specified)
IMSI                        : (Not Specified)
Last move time              : 2013/07/02 07:45:31
 
----------------------------------------------------------------------
No. of UE: 1
======================================================================
System#
 
 
 
Tools Commands
acct-on
Syntax
acct-on [radius-server-policy policy-name] [force]
Context
tools>perform>aaa
Description
This command triggers a RADIUS Accounting-On message:
The Accounting-On message is not sent when the last successful event for the radius server policy was an Accounting-On message. In this case, an Accounting-Off should be sent first. By specifying the keyword “force”, this is overruled.
Parameters
radius-server-policy policy-name
Specifies the radius-server-policy for which the Accounting-On should be sent.
force
Sends an Accounting-On also if the last successful event was an Accounting-On.
acct-off
Syntax
acct-off [radius-server-policy policy-name] [force] [acct-terminate-cause number]
Context
tools>perform>aaa
Description
This command triggers a RADIUS Accounting-Off message:
The Accounting-Off message is not sent when the last successful event for the radius server policy was an Accounting-Off message. In this case, an Accounting-On should be sent first. By specifying the keyword “force”, this is overruled.
Parameters
radius-server-policy policy-name
Specifies the radius-server-policy for which the Accounting-Off should be sent.
force
Sends an Accounting-On also if the last successful event was an Accounting-Off.
acct-terminate-cause number
Overrides the default Acct-Terminate-Cause (User-Request) in the Accounting-Off message.
radius-server-policy
Syntax
radius-server-policy policy-name msg-buffer [session-id acct-session-id]
Context
tools>perform>aaa
Description
This command dumps the RADIUS message buffer content for the specified radius-server-policy:
When specifying the session-id, the message details are displayed.
Parameters
policy-name
Specifies the radius-server-policy for which the message buffer content should be displayed.
session-id acct-session-id
Display the RADIUS message details for the message with specified session-id that is stored in the RADIUS message buffer.
ue
Syntax
ue
Context
tools>dump>wlan-gw
Description
This command dumps user equipment (UE) information.
Sample Output
tools dump wlan-gw ue
===============================================================================
Matched 1 session on Slot #4 MDA #1
===============================================================================
UE-Mac          : 00:02:00:00:00:11     UE-vlan         : 3600
UE IP Addr      : N/A                   UE timeout      : N/A
UE IP6 Addr     : N/A
Description     : L2-user
Auth/CoA-time   : 01/07/2015 18:56:01
Tunnel MDA      : 5/1                   Tunnel Router   : 50
MPLS label      : N/A                   Shaper          : Default
Tunnel Src IP   : 201.0.0.2             Tunnel Dst IP   : 50.1.1.1
Tunnel Type     : GRE
Anchor SAP      : 4/1/nat-out-ip:2049.6
AP-Mac          : Unknown               AP-RSSI         : Unknown
AP-SSID         : Unknown
Last-forward    : 01/07/2015 18:56:01   Last-move       : None
Session Timeout : None                  Idle Timeout    : 300 sec
Acct Update     : None                  Acct Interval   : N/A
Acct Session-Id : N/A
Acct Policy     : N/A
NAT Policy      : N/A
Redirect Policy : N/A
IP Filter       : N/A
App-profile     : N/A
Rx Oper PIR     : N/A                   Rx Oper CIR     : N/A
Tx Oper PIR     : N/A                   Tx Oper CIR     : N/A
Rx Frames       : 0                     Rx Octets       : 0
Tx Frames       : 0                     Tx Octets       : 0
-------------------------------------------------------------------------------
===============================================================================
No sessions on Slot #4 MDA #2 match the query
No sessions on Slot #5 MDA #1 match the query
No sessions on Slot #5 MDA #2 match the query
 
 
Clear Commands
radius-server-policy
Syntax
radius-server-policy policy-name msg-buffer [acct-session-id acct-session-id]
radius-server-policy policy-name statistics [msg-buffer-only]
radius-server-policy policy-name server server-index statistics
Context
clear>aaa
Description
This command dumps the RADIUS message buffer content for the specified radius-server-policy:
- message-type (acct-interim or acct-stop)
- Acct-Session-Id
- Remaining lifetime
When specifying the session-id, the message details are displayed.
Parameters
policy-name
Specifies the radius-server-policy for which the information should be cleared.
msg-buffer [acct-session-id acct-session-id]
Deletes all RADIUS messages or the RADIUS message with specified session-id from the RADIUS message buffer.
statistics [msg-buffer-only]
Clears all statistics for the specified radius-server-policy: radius-server-policy statistics, RADIUS server statistics and RADIUS message buffer statistics. With the optional keyword “msg-buffer-only”, only the RADIUS message buffer statistics are cleared.
server server-index statistics
Clears the RADIUS server statistics for the specified server-index in the specified radius-server-policy.
isa-subnets
Syntax
isa-subnets all
isa-subnets interface ip-int-name
isa-subnets prefix ipv6-address/prefix-length
Context
clear>router>wlan-gw
Description
This command clears specific subnets from the pool-manager. Associated UE’s will be removed from the system.
When clearing the last subnet on an ISA the pool-manager will automatically allocate a new subnet with allocation-level 0%.
Parameters
all
Clears all the isa-subnets.
interface ip-int-name
Clears all the isa-subnets of a specific subscriber-interface.
ipv6-address/prefix-length
Clears a specific IPv6 address and prefix length.