The following table shows the provisionable port parameters.
Parameter |
TL1 Commands (Access) (Note) |
Range |
Default |
Related WaveStar® CIT Commands |
---|---|---|---|---|
BPV to All Zeroes Translation on Incoming DS1 (bpv) 1 |
ENT-T1 (P, G) |
N,Y |
N |
Configuration → Equipment |
DS1 Incoming Signal Format (fmt) |
SF, ESF, ESFN, UF |
ESF | ||
DS1 Line Code (linecde)1 |
AMI, B8ZS |
AMI | ||
DS1 Line Buildout (lbo)1 |
20 (0–133 ft.), 40 (133–267 ft.), 60 (267–420 ft.), 80 (420–550 ft.), 100 (550–655 ft.) |
20 | ||
Interface Type (intftype) |
ED-EQPT (P, G) |
E1, DS1 |
||
E1 Signal Format (fmt) |
ENT-E1 (P, G) |
FAS, CRC4 |
CRC4 | |
DS3 AIS |
ENT-T3 (P, G) |
Y, N |
N | |
DS3/EC1 Mode (eif) LNW19/19B and LNW20 only LNW16: Hardware Settable |
ENT-T3 ENT-EC1 (P, G) |
DS3, EC1 |
DS3 | |
Line Buildout (lbo) |
ENT-EC1 ENT-T3 (P, G) |
728A/B Cable: IN (0–225), OUT (225–450) 735A Cable: IN (0–112), OUT (112–225) |
IN |
Configuration → Equipment |
DS3 Line Coding (linecde) |
ENT-T3 (P, G) |
B3ZS, CCHAN1 |
B3ZS | |
DS3 Frame Format (frame) |
M13, CBIT, CCHAN1 |
M13 | ||
P-bit Violation Removal (pbit) |
ON, OFF |
ON | ||
DS3 Incoming Signal Format (fmt) |
PBIT, FMBIT, CPBIT |
PBIT | ||
TCA Monitoring Mode (tcamd) |
ENT-E1 ENT-T1 ENT-T3 ENT-EC1 ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 ENT-OCH ENT-OTS ENT-OTU2 (P, G) |
ENABLE, DISABLE |
ENABLE |
Performance → Prov PM Settings |
Alarm Severity Assignment Profile (pfname) |
ENT-ASAP-ASGNMT (P, G) |
DEFAULT ASAP User-Created ASAP |
DEFAULT ASAP |
Configuration → Equipment |
Primary State (pst) |
ENT-E1 ENT-T1 ENT-T3 ENT-EC1 ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 ENT-OCH ENT-OTS ENT-OTU2 (P, G) |
OOS (NMON) OOS-MA-AS (AUTO) IS (In Service) |
AUTO |
Configuration → Equipment |
Signal Failure Threshold (sfthr) |
ENT-E1 ENT-T1 ENT-T3 ENT-EC1 (P, G) |
-3, -6, -7, -8 -3, -6, -7, -8 -4, -6 -3, -5, -6, -7, -8, -9 |
-3 -3 -6 -6 | |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
-5, -6, -7, -8, -9 |
-6 | ||
Signal Fail Threshold (sfail) |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
-3, -4, -5 |
-3 | |
PJC Monitor Point (pjcmon) |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
N (number of STSn tributary), AUTO AUTO-NO-TCA |
AUTO-NO-TCA |
Performance → Prov PM Settings |
Transmission Protection (application) (low-speed slots) |
ENT-OC3 ENT-OC12 ENT-OC48 (P, G) |
0x1S1 (non-VLF Mains), 0x1S2 (non-VLF Mains), 0x1 (VLF Mains), 1+1, 1+1_BIDIR, UPSR |
1+1 |
Configuration → Equipment |
Transmission Protection (application) (high-speed slots) |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
UPSR, 1+1, 1+1_BIDIR 0x1 (VLF Mains only) |
UPSR | |
Transmission Protection (application) (LNW705 XM10G/8 circuit pack client ports only) |
ENT-OC3 ENT-OC12 ENT-OC48 (P, G) |
0x1 |
0x1 | |
Socket Maintenance State (mst) |
ED-EQPT (P, G) |
Normal, Maintenance |
Normal | |
Expected DWDM Frequency (efreq) |
NA 9200 to 9590 in increments of 10 Auto |
NA | ||
Default Port Maintenance (portmntc_default) |
ENT-SYS (P) |
Allow, Inhibit |
Allow |
Configuration → Equipment |
PDH port Equipment Fault Control (pdheqfltctl) |
Enabled, Disabled |
Disabled | ||
Transmit Section Trace Format (strcwfmt) Expected Receive Section Trace Format (strcfmt) |
ENT-EC1 ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
EC-1: 1, 2 OC-3/12/48/192: 1, 2, 16, 64 |
2 | |
Transmit Section Trace Value - Hexadecimal (strcout) Expected Receive Section Trace Value - Hexadecimal (exprstrc) |
characters 0–9 and A–F in a string up to twice the number specified by the format |
Format 1=00 Format 16=89 Format 64=C8 | ||
Transmit Section Trace Value - ASCII (strcouttxt) Expected Receive Section Trace Value - ASCII (exprstrctxt) |
ENT-EC1 ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
Any characters except semicolon, double quote, and backslash. Format 1=1 character Format 16 =15 characters Format 64=63 characters |
Null |
Configuration → Equipment |
Receive Section Trace Identifier Monitor (rstimmon) |
Enable, Disable |
Disable | ||
Receive Section Trace Identifier Mismatch Consequent Action (rstimca) |
Enable, Disable |
Disable | ||
Port Mode (pmd) (LNW20 only) |
ENT-T3 (P, G) |
PORTED, PORTLESS (odd ports only with non-VLF Mains, all ports with VLF Mains) |
PORTED |
Configuration → Equipment |
Tributary Mode (tribmod) (LNW20 only) |
ENT-T3 (P, G) |
UNCHAN, CHAN |
UNCHAN | |
Signal Type (signaltype) |
ENT-STNA ENT-OC3 ENT-OC12 ENT-OC48 (P, G) |
STNA, OC3, OC12, OC48 |
STNA (No expected circuit pack type or unprotected companion), or Same value as protected companion | |
Signal Type (signaltype) (LNW705 client ports only) |
ENT-OTPE (P, G) |
STNA, OC3, OC12, OC48, 1GE, FC100, FC200, FICON, FICON_EXP |
STNA |
Configuration → Equipment |
Forward Error Correction Type (fectype) |
ENT-OTU2 (P, G) |
EFEC: Enhanced FEC NOFEC: No FEC RSFEC: Industry-standard Reed-Solomon FEC |
EFEC | |
Transmit Fiber Type (tx_ftype) |
ENT-OTS (P, G) |
SSMF: not provisionable |
SSMF | |
Receive Fiber Type (rx_ftype) | ||||
SS Bits (ssbits) (port level) (LNW55, LNW62, LNW84, and LNW141 only) |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-OC192 (P, G) |
SS00, SS10 |
SS00 | |
1Does not apply to the TMUX circuit pack. Note: The TL1 command security access levels are Privileged (P), Administration (A), General (G), Maintenance (M), and Reports-only (R). |
November 2011 | Copyright © 2011 Alcatel-Lucent. All rights reserved. |