The following table shows the provisionable port parameters.
|
Parameter |
TL1 Commands (Access) (Note) |
Range |
Default |
Related WaveStar® CIT Commands |
|---|---|---|---|---|
|
DS1 Incoming Signal Format (fmt) |
ENT-T1 (P, G) |
SF, ESF, ESFN, UF |
ESF |
Configuration → Equipment |
|
DS1 Line Code (linecde) |
AMI, B8ZS |
B8ZS | ||
|
DS1 Line Buildout (lbo) |
20 (0-133 ft.), 40 (133-267 ft.), 60 (267-420 ft.), 80 (420-550 ft.), 100 (550-655 ft.) |
20 | ||
|
DS1 inband loopback from DSX (inbandlpbkdsx) |
Enable, Disable |
Disable | ||
|
DS1 inband loopback from fiber (inbandlpbkfiber) |
Enable, Disable |
Disable | ||
|
Port Mode (pmd) (DS1 in A group or DS1 in Channelized b-3 DS3) |
Avail, Unavail |
Avail | ||
|
E1 Signal Format (fmt) |
ENT-E1 (P, G) |
FAS, CRC4 |
CRC4 | |
|
E1 Line Code (linecde) |
HDB3 (not provisionable or retrievable) |
HDB3 | ||
|
DS3 AIS |
ENT-T3 (P, G) |
Y, N |
N | |
|
Line Buildout (lbo) |
ENT-T3 (P, G) |
728A/B Cable: IN (0-225), OUT (225-450) 735A Cable: IN (0-112), OUT (112-225) |
IN |
Configuration → Equipment |
|
DS3 Line Coding (linecde) |
ENT-T3 (P, G) |
B3ZS, CCHAN1 |
B3ZS |
Configuration → Equipment |
|
DS3 Frame Format (frame) |
M13, CBIT, CCHAN1 |
M13 | ||
|
P-bit Violation Removal (pbit) |
ON, OFF |
ON | ||
|
DS3 Incoming Signal Format (fmt) |
PBIT, FMBIT, CPBIT |
PBIT | ||
|
Tributary Mode (tribmd) (b-3 port only) |
Unchan, Chan |
Unchan | ||
|
FEAC loopback requests from DSX (feaclpbkdsx) (b-3 port only) |
Enable, Disable |
Disable | ||
|
TCA Monitoring Mode (tcamd) |
ENT-E1 ENT-T1 ENT-T3 ENT-OC3 ENT-OC12 ENT-OC48 ENT-STM1 ENT-STM4 ENT-STM16 (P, G) |
Enable, Disable |
Enable |
Performance → Prov PM Settings |
|
Incoming Signal Failure Alarm Level (ntfcncde) |
ENT-E1 ENT-E3 ENT-T1 ENT-T3 (P, G) |
DS1/E1: MJ, MN, NA DS3/E3: CR, MJ, MN, NA |
DS1/E1: NA DS3/E3: CR |
Configuration → Equipment |
|
Signal Failure Threshold (sfthr) |
ENT-E1 ENT-T1 (P, G) |
-3, -6, -7, -8 |
-3 | |
|
ENT-E3 ENT-T3 (P, G) |
-4, -6 |
-6 | ||
|
Primary State (pst) |
ENT-E1 ENT-E3 ENT-T1 ENT-T3 (P, G) |
OOS-MA-AS (AUTO), OOS (NMON) |
AUTO | |
|
Alarm Indication Signal (AIS) Notification for Non-Service Affecting Alarms (aisnc) |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-STM1 ENT-STM4 ENT-STM16 (P, G) |
CR, MJ, MN, NA |
NA |
Configuration → Equipment |
|
Line Remote Defect Indicator (rdi-l) |
MJ, MN, NA |
NA | ||
|
Signal Degrade Threshold (sfthr) |
-5, -6, -7, -8, -9 |
-6 | ||
|
Signal Fail Threshold (sfail) |
-3, -4, -5 |
-3 | ||
|
PJC Monitor Point (pjcmon) |
ENT-OC3 ENT-OC12 ENT-OC48 (P, G) |
N (number of STSn tributary to be monitored), AUTO AUTO-NO-TCA |
AUTO-NO-TCA |
Performance → Prov PM Settings |
|
Transmission Protection (application) |
ENT-OC3 ENT-OC12 ENT-OC48 (P, G) |
UPSR, 1+1, 0x1 |
0x1 |
Configuration → Equipment |
|
ENT-STM1 ENT-STM4 ENT-STM16 (P, G) |
SNCP, 1+1, 0x1 |
0x1 | ||
|
Signal Type (signaltype) |
ENT-OC3 ENT-OC12 ENT-OC48 (P, G) |
OC3, OC12, OC48 |
OC3 | |
|
ENT-STM1 ENT-STM4 ENT-STM16 (P, G) |
STM1, STM4 |
STM1 | ||
|
Primary State (pst) |
ENT-OC3 ENT-OC12 ENT-OC48 ENT-STM1 ENT-STM4 ENT-STM16 (P, G) |
OOS-MA-AS (AUTO), OOS (NMON) |
AUTO | |
|
Slot protection state (prot_state) |
ED-EQPT (P, G) |
Prot, Unprot |
Unprot | |
|
Note: The TL1 command security access levels are Privileged (P), Administration (A), General (G), Maintenance (M), and Reports-only (R). | ||||
| Copyright © 2011 Alcatel-Lucent. All rights reserved. |