The following table shows the provisionable Ethernet parameters.
|
Parameter |
TL1 Commands (Access) (Note) |
Range |
Default |
Related WaveStar® CIT Commands |
|---|---|---|---|---|
|
Ethernet Port Monitoring Mode (epmode) |
ED-EPORT (P, G) |
auto, nmon, is |
auto |
Configuration → Equipment |
|
Ethernet Port PM Enabled (eppm) |
enable, disable |
enable | ||
|
Flow Control Mode (fcmd) |
enable, disable, auto, drop |
disable | ||
|
Alarm Level (almlvl) |
CR, MJ, MN, NA |
CR | ||
|
Line Rate (lnrate) (Electrical FE ports only) |
10M, 100M, Auto |
Auto | ||
|
Crossover Mode (mdix) (Electrical FE ports only) |
Auto, MDIX, MDI |
Auto | ||
|
Remote Client Fail (rcf) |
enable, disable |
disable | ||
|
Remote Client Fail Link Shutdown (rcf_linkdown) |
ED-EPORT (P, G) |
enable, disable |
enable |
Configuration → Equipment |
|
Remote Client Fail Alarm Level (rcf_almlvl) |
CR, MJ, MN, NA |
NA | ||
|
Port Admin Control (admin) |
enable, disable |
enable | ||
|
TCA Monitoring Mode (tcamd) |
enable, disable |
disable | ||
|
MTU (Maximum Transmission Unit) Size (mtu_size) |
1500 - 9614 (NOTAG) 64 - 2048 (MUX) |
1500 | ||
|
Auto-Negotiation (autoneg) |
ED-EPORT (P, G) |
enable, disable |
disable |
Configuration → Equipment |
|
Pass As Is, Unmatch (pai_unmatch |
0 or 1 - 8 |
1 | ||
|
Add Port Tag ID (addporttag) |
ED-VCG (P, G) |
1 - 4093 (Up to 32 Port Tag IDs across 8 VCGs) |
None |
Configuration → Equipment |
|
Default Port Tag ID (dftporttag) |
0 - 4093 |
0 | ||
|
Delete Port Tag ID (delporttag) |
1 - 4093 |
None | ||
|
Tag Filter (tagfilter) |
Enable, Disable |
VCG2-8: Enable VCG1: Disable | ||
|
Ethernet Type Field (TPID) (ethertype) |
0601 to FFFF (hexadecimal) |
8100 (hexadecimal) | ||
|
CSF Management mode (csfmd) |
Enable, Disable |
Disable | ||
|
VCG Monitoring Mode (vmode) |
ED-VCG (P, G) |
auto, nmon |
auto |
Configuration → Equipment |
|
VCG PM Enable (vpm) |
enable, disable |
enable | ||
|
Alarm Level (almlvl) |
CR, MJ, MN, NA |
CR | ||
|
TCA Monitoring Mode (tcamd) |
enable, disable |
disable | ||
|
GFP Frame Check Sequence (gpf_fcs) |
enable, disable |
disable | ||
|
Virtual Concatenation Mode (vcat) |
enable, disable |
enable | ||
|
LCAS Mode (lcasmd) |
ED-VCG (P, G) |
Enable, Disable |
Disable |
Configuration → Equipment |
|
Hold-Off Timer (htmr) |
0 - 10000 |
200 | ||
|
Wait-To-Restore (wtr) |
0 - 3600 |
5 | ||
|
Input Membership (source) (inmbs) |
ED-VCGTRIB (P, G) |
disable, enable |
disable |
Configuration → Equipment |
|
Output Membership (sink) (outmbs) |
disable, enable |
disable | ||
|
Ethernet Port Mode (enetmd) |
ED-EQPT (P, G) |
GX Not provisionable |
GX |
Configuration → Equipment |
|
LAN interface (lanintf) |
BP, PTM |
PTM | ||
|
VLAN Tagging Mode (vlantagmd |
NOTAG, MUX |
NOTAG | ||
|
Note: The TL1 command security access levels are Privileged (P), Administration (A), General (G), Maintenance (M), and Reports-only (R). | ||||
| Copyright © 2011 Alcatel-Lucent. All rights reserved. |