LSP Throughput with Forecast report

LSP Throughput with Forecast report overview

The LSP Throughput with Forecast report provides the LSP throughput with forecasting data.

The report can generate a forecast depending on the granularity. For raw and hourly granularities, forecast periods and periods per season are ignored. To generate a forecast, you must provide at least two seasons of data, although more may be required if the input data is not linear. For example, if you choose a seasonality value of 7 and the granularity is daily, you must use a report range of at least 14 days.

When the forecast algorithm fails, a pop-up message displays with the recommendation that you either lower the seasonality value or increase the report range.

The aggregation time zone and the session time zone must be same.

You may consider scheduling the report, as it takes several minutes to generate.

Prerequisites

The session time zone must match the aggregation time zone. When these two settings are different, the report does not run correctly and the system returns an error. See section How do I configure the Analytics session time zone? for more information about configuring the session time zone.

For an LSP Throughput with Forecast report to be created, the following items must be enabled:

vRtrMplsLspStatisticsEntry
MPLS LSP Egress Aggregator to see MPLS utilization data; see How do I configure analytics aggregation?

The following table describes the aggregation rules that must be enabled and the accounting policies that must be configured for the NEs on which statistics are to be collected; see the NSP NFM-P Statistics Management Guide for information about configuring an accounting policy. To view the report for granularities other than raw data, the aggregation rules must be enabled; see How do I configure analytics aggregation?.

Table 14-35: LSP Throughput with Forecast report prerequisites

Aggregator name	Monitored object class	Statistics class	Statistics collection	MIB	NE types
MPLS LSP Egress Aggregator	mpls.DynamicLsp mpls.P2MPDynamicLsp mpls.SegmentRoutingTeLsp	mpls.mplsLspEgress	Performance statistics	TIMETRA -MPLS- MIB.vRtr MplsLsp Statistics Entry	7705 SAR 7750 SR Note: 7210 SAS and 7250 IXR are not supported

Aggregator name

Monitored object class

Statistics class

Statistics collection

MIB

NE types

MPLS LSP Egress Aggregator

mpls.DynamicLsp

mpls.P2MPDynamicLsp

mpls.SegmentRoutingTeLsp

mpls.mplsLspEgress

Performance statistics

TIMETRA -MPLS- MIB.vRtr MplsLsp Statistics Entry

7705 SAR

7750 SR

Note: 7210 SAS and 7250 IXR are not supported

Use cases

Capacity planning—Use the report to examine LSP throughput data for planning future capacity requirements.

Report characteristics

The following table lists the principal report characteristics.

Table 14-36: LSP Throughput with Forecast report characteristics

Characteristic	Value
Data type	Statistics
Source database	Auxiliary database
LSP types supported	Dynamic, P2MP Dynamic, SR TE
Report inputs	Prompt	Notes
	End date	Calendar date or relative date (for example, two days ago) and time
	Report Range	Length of time to be reported, in hours or days
	Granularity	Aggregation types: None (raw data) Hourly Daily Monthly
	NE type	Select individual items.
	Name or name pattern for NE	Search using partial names or wildcard (%). Select individual items.
	NE	Select individual items.
	Name or name pattern for LSP	Search using partial names or wildcard (%). Select individual items.
	LSP	Select individual items. You must enter data for this field.
	Forecast Periods	The range for the forecast to work. The value is based on the granularity selected. For example, a period of 30 would mean 30 days if the granularity is daily, and 30 months if the granularity is monthly.
	Periods per Season	The frequency at which there is a similarity in data. For example, the frequency at which a plot has similar values. The behavior is the same as the forecast period. For example, a period of 7 would mean 7 days if the granularity is daily, and 7 months if the granularity is monthly.
	Logo Resource ID	The logo to add to the report. Enter the resource ID for the logo image uploaded to the Images folder, if any. If no logo ID is provided, the logo area will be blank.
	Logo Position	Choose Left, Middle or Right. The logo will be placed on the left of the first page of the report for both the left and middle options.
	Show report output on one page	Select the check box to enable pagination. Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.
Drill-down support	No

Example

The following figures show report examples.