OAM-PM Network Site Summary (NSP) report

Overview

The OAM-PM Network Site Summary (NSP) report differs from the OAM-PM Network Site Summary report by including OAM data for NEs managed by the NFM-P and MDM (model-driven Nokia NEs). The report shows the aggregated PM sessions for a selected source and target NE with collected bin type data, aggregated by session name.

The report includes the following session types:

Use cases

QoS analysis—Identify potential service impacting issues based on thresholds for latency, jitter and packet loss between specific NEs.

Prerequisites

The following sessions need to be performed in the NSP and NFM-P for the report to be created:

Report inputs

The following table shows the report inputs.

Table 17-13: OAM-PM Network Site Summary (NSP) report inputs

Prompt

Notes

Session Type

ETH-CFM Session, TWAMP-Light Session

End Date

Calendar date or relative date (for example, two days ago) and time

Granularity

Aggregation types:

  • None (raw collection interval)

  • Hourly

  • Daily

  • Monthly

Report range

Length of time to be reported, in hours, days, or months

Source Node

Search using partial or full names.

Select individual items or click Select All.

Both the NE name and its IP address display.

Target Node

Bin Type

Bin types configured in the NSP and NFM-P

Result set limit

Number of results to report

Interval Duration

5 minutes, 15 minutes, 1 hour, or 1 day

Logo resource ID

The logo to add to the report. Enter the Resource ID of the logo image in the Images folder.

The default is the Nokia logo. To create the report without a logo, leave the Logo Resource ID field blank.

Logo Position

Choose Left, Middle, or Right. The logo appears on the left on the first page of the report if you choose Left or Middle.

Show report output on one page

Select the check box to enable pagination.

Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.

Report characteristics

The following table lists the principal report characteristics.

Table 17-14: OAM-PM Network Site Summary (NSP) report characteristics

Characteristic

Value

Data type

OAM session statistics

Source database

Auxiliary database

NE types supported

7210 SAS-M 24F, 7210 SAS-M 24F 2XFP, 7210 SAS-M 24F 2XFP ETR, 7210 SAS-T 12F 10T 4XFP, 7210 SAS-T 12F 10T 4XFP ETR, 7210 SAS-X 24F 2XFP, 7210 SAS-K, 7210 SAS-R6, 7210 SAS-R12, 7210 SAS-S/SX 1/10GE VC

7250 IXR-6, 7250 IXR-R6, 7250 IXR-s, 7250 IXR-10, 7250 IXR-e

all 7450 ESS variants

all 7750 SR variants

all 7950 XRS variants

Drill-down support

Yes:

  • Click on a delay result to show an OAM-PM Latency (NSP) report.

  • Click on a jitter or loss result to show an OAM-PM Loss (NSP) report.

Example

The following figures show report examples.

Figure 17-17: OAM-PM Twamp-Light Network Site Summary (NSP) – Frame Delay
OAM-PM Twamp-Light Network Site Summary (NSP) – Frame Delay
Figure 17-18: OAM-PM Twamp-Light Network Site Summary (NSP) – Frame Delay Range
OAM-PM Twamp-Light Network Site Summary (NSP) – Frame Delay Range
Figure 17-19: OAM-PM ETH-CFM Network Site Summary (NSP) – Inter Frame Delay Variation
OAM-PM ETH-CFM Network Site Summary (NSP) – Inter Frame Delay Variation
Figure 17-20: OAM-PM ETH-CFM Network Site Summary (NSP) – Frame Delay Range
OAM-PM ETH-CFM Network Site Summary (NSP) – Frame Delay Range