To configure a subscriber profile

Steps
 

Choose Policies→Residential Subscriber from the NFM-P main menu. The Residential Subscriber Policies form opens.


CAUTION 

CAUTION

Service Disruption

Modifying an active subscriber profile is potentially service-affecting.

Ensure that you consider the implications of reconfiguring the subscriber profile before you proceed.

Click Create→Subscriber Profile or choose an existing Subscriber Profile and click Properties. The Subscriber Profile (Create|Edit) form opens.


Configure the required parameters.

You can designate a subscriber profile as the default profile by specifying the case-sensitive name “default” for the Displayed Name parameter. The Displayed Name parameter is configurable only during subscriber profile creation.

The Egress Aggregate Rate Limit and Frame Base Accounting parameters are configurable only when a scheduler is not specified in the Egress Scheduler panel.

The Virtual Port Hashing parameter applies only to standard LAG ports. The Secondary Shaper Hashing parameter applies only to HSMDA and HSQ ports. Both of these parameters can also be configured on a local definition of an existing subscriber profile, accessed on the Local Definitions tab.


Configure policies to associate with the subscriber profile.

  1. Select an accounting policy in the Accounting Policy panel and configure the Volume Stats Type parameter.

  2. Configure the required policy objects on the subscriber profile:
    • ANCP policy

    • host tracking policy

    • NAT policy

    • IGMP policy

    • MLD policy

    • subscriber multicast CAC policy

    • PIM policy

    • UPnP policy

    • NAT prefix list (NAT policy must also be configured)

    • Firewall policy


Click on the Scheduling tab and configure the required parameters.

An additional parameter, Encapsulation Offset Mode, can be configured using the XML API.


Configure LAG per-link hashing parameters, if required.


Select an ingress or egress scheduler in the Ingress or Egress panel.

You cannot specify an egress scheduler in a subscriber profile when the Egress Aggregate Rate Limit parameter is set to a value greater than zero.


Configure HS Egress Aggregate Rate Limit parameters, as required.


Click on the RADIUS Accounting tab and select first, second, and third RADIUS accounting policies. Depending on the NE version, the third RADIUS accounting policy option may not be displayed.

If you configure the Optimize for Session Accounting parameter to reduce accounting messages in a dual stack PPP session configuration, you must also configure the Delay Start Time parameter on the RADIUS accounting policies; see To configure a RADIUS-based accounting policy.


10 

Click on the SLA Profiles tab to configure SLA profiles for the subscriber profile.

  1. On the General tab, configure the Use Direct Map as Default and HS SLA Profile Handling Mode parameters.

  2. Click on the Profiles tab.

  3. Click Create or choose an SLA profile entry and click Properties. The SLA Profile Entry (Create|Edit) form opens.

  4. Configure the SLA Profile String parameter.

  5. Select an SLA profile to associate with the subscriber profile.

  6. Save your changes and close the form.


11 

Click on the HSMDA QoS tab and perform one of the following:

  1. Select an ingress policy in the Ingress panel.

  2. Select an egress policy in the Egress panel and configure the Aggregate Rate Limit parameter.


12 

Select a WRR policy in the Egress HSMDA Override panel and configure the Packet Byte Offset parameter, if required.


13 

Click on the Policer Control tab to configure ingress and egress policer control policies.

  1. Select a policer control policy in the Ingress Policer Control Policy panel.

  2. Configure local override parameters for the selected ingress policer control policy, if required.

  3. Select a policer control policy in the Egress Policer Control Policy panel.

  4. Configure local override parameters for the selected egress policer control policy, if required.


14 

Click on the Override Policy Items tab to specify local overrides for schedulers, queues, or policers assigned to the subscriber profile.


15 

On the Ingress Schedulers tab, click Create or choose an ingress scheduler entry and click Properties. The Ingress Scheduler Entry Override (Create|Edit) form opens.

  1. Select a scheduler policy.

  2. Click on the Override tab and configure the required parameters.

    The CIR parameter can only be configured when Summed CIR is set to false.

  3. Save your changes and close the form.


16 

On the Egress Schedulers tab, click Create or choose an egress scheduler entry and click Properties. The Egress Scheduler Entry Override (Create|Edit) form opens.

  1. Select a scheduler policy.

  2. Click on the Override tab and configure the required parameters.

    The CIR parameter can only be configured when Summed CIR is set to false.

  3. Save your changes and close the form.


17 

On the Ingress Policer Level tab, click Create or choose an ingress policer level override entry and click Properties. The Ingress Policer Level Override (Create|Edit) form opens.

  1. Select a policer level.

    The current maximum cumulative buffer space value for the policer level is displayed.

  2. Click on the Override tab and then enable and configure the Maximum Cumulative Buffer Space (bytes) parameter.

  3. Save your changes and close the form.


18 

On the Egress Policer Level tab, click Create or choose an egress policer level override entry and click Properties. The Egress Policer Level Override (Create|Edit) form opens.

  1. Select a policer level.

    The current maximum cumulative buffer space value for the policer level is displayed.

  2. Click on the Override tab and then enable and configure the Maximum Cumulative Buffer Space (bytes) parameter.

  3. Save your changes and close the form.


19 

On the HSMDA Ingress Queues tab, click Create or choose an access ingress HSMDA queue override entry and click Properties. The Access Ingress HSMDA Queue Override (Create|Edit) form opens.

  1. Select an access ingress policy queue.

  2. To configure separate IPv4 and IPv6 statistics counters for the queue override, click on the Override tab and configure the Stat Mode parameter.

  3. Save your changes and close the form.


20 

On the HSMDA Ingress Policers tab, click Create or choose an access ingress HSMDA policer override entry and click Properties. The Access Ingress HSMDA Policer Override (Create|Edit) form opens.

  1. Select an access ingress policy policer.

  2. To configure separate IPv4 and IPv6 statistics counters for the policer override, click on the Override tab and configure the Stat Mode parameter.

  3. Save your changes and close the form.


21 

On the Access Egress HSMDA Queues tab, click Create or choose an access egress HSMDA queue override entry and click Properties. The Access Egress HSMDA Queue Override (Create|Edit) form opens.

  1. Select an access egress policy queue.

  2. To specify override values for the queue, click on the Override tab and configure the required parameters.

    If you enable the Override check box for any of these parameters, then the original value of the parameter that was configured for the Access Egress HSMDA Queue will appear in that parameter’s value field. You can then configure the override value for that parameter.

    You can only specify an override value for WRR Weight for queues 1, 2, or 3.

  3. Select an HSMDA slope policy.

  4. Save your changes and close the form.


22 

Click OK to save the policy and close the form, or click Apply to save the policy. See To release and distribute a policy to distribute the policy to NEs.

End of steps