To configure a time-of-day suite policy

General Information

Consider the following when you create a time-of-day suite policy:

  • when there are overlapping time range policy entries within a time-of-day suite policy, the time range policy entry with the highest priority is applied first

  • only one time-of-day suite policy entry without a time range (default NO-TIME-RANGE) is allowed for each type of policy

  • you cannot modify a time-of-day suite policy entry after you create the entry

  • you cannot assign the same priority of a global policy within the same policy type

  • you cannot assign the same priority of a local policy within the same policy type

  • you cannot assign the same time range of a global policy within the same policy type

  • you cannot assign the same time range a local policy within the same policy type

  • you cannot distribute a time-of-day suite policy entry to a local policy if the local policy already has been assigned the same time range as the global policy

  • you cannot distribute a time-of-day suite policy entry to a local policy if the local policy already has been assigned the same priority as the global policy

  • all time-of-day suite policy entries of a local policy are replaced by the time-of-day suite policy entries of a global policy if none of the entries from the local policy have the same priority or time ranges as the global policy

Steps
 

Choose Policies→Time of Day→Time Of Day Suite from the NFM-P main menu. The Time Of Day Suite Policies form opens.


Click Create, or choose a policy and click Properties. The Time of Day Suite (Create) form opens.


Configure the required general parameters.


Click on the TOD Suite Entries tab.


Configure time-of-day suite entries for ingress traffic. Click on the Ingress tab and perform any of the following:

  1. Associate time ranges with ingress filter policies.

    1. Click on the IP Filter, IPV6 Filter or MAC Filter tab. A list of available time range policies is displayed.

    2. Click Create, or choose an entry in the list and click Properties. The Ingress type_of_filter (Create) form opens.

    3. Configure the Priority parameter.

    4. Click Select in the Time range panel and choose a time range policy.

    5. Click Select in the Policy ID panel and choose a filter policy.

    6. Save your changes and close the form.

  2. Associate time ranges with ingress QoS policies.

    1. Click on the QoS tab. A list of available time range policies is displayed.

    2. Click Create, or choose an entry in the list and click Properties. The Ingress QoS (Create) form opens.

    3. Configure the Priority parameter.

    4. Click Select in the Time range panel and choose a time range policy.

    5. Click Select in the Policy panel, or 7210 Policy panel, and choose a QoS policy.

    6. Save your changes and close the form.

  3. Associate time ranges with ingress scheduler policies.

    1. Click on the Schedulers tab. A list of available time range policies is displayed.

    2. Click Create, or choose an entry in the list and click Properties. The Ingress Scheduler (Create) form opens.

    3. Configure the Priority parameter.

    4. Click Select in the Time range panel and choose a time range policy.

    5. Click Select in the Policy Name panel and choose a scheduler policy.

    6. Save your changes and close the form.


Configure time-of-day suite entries for egress traffic. Click on the Egress tab and perform any of the following:

  1. Associate time ranges with egress filter policies.

    1. Click on the IP Filter, IPV6 Filter or MAC Filter tab. A list of available time range policies is displayed.

    2. Click Create, or choose an entry in the list and click Properties. The Egress type_of_filter (Create) form opens.

    3. Configure the Priority parameter.

    4. Click Select in the Time range panel and choose a time range policy.

    5. Click Select in the Policy ID panel and choose a filter policy.

    6. Save your changes and close the form.

  2. Associate time ranges with egress QoS policies.

    1. Click on the QoS tab. A list of available time range policies is displayed.

    2. Click Create, or choose an entry in the list and click Properties. The Egress QoS (Create) form opens.

    3. Configure the Priority parameter.

    4. Click Select in the Time range panel and choose a time range policy.

    5. Click Select in the Policy ID panel and choose a QoS policy.

    6. Save your changes and close the form.

  3. Associate time ranges with egress scheduler policies.

    1. Click on the Schedulers tab. A list of available time range policies is displayed.

    2. Click Create, or choose an entry in the list and click Properties. The Egress Scheduler (Create) form opens.

    3. Configure the Priority parameter.

    4. Click Select in the Time range panel and choose a time range policy.

    5. Click Select in the Policy Name panel and choose a scheduler policy.

    6. Save your changes and close the form.


Click OK to save the policy and close the form, or click Apply to save the policy. See To release and distribute a policy to distribute the policy to NEs.

End of steps