| |
|
1 |
Choose Manage→Service→Services from the NFM-P main menu. The Manage Services form opens.
|
2 |
Choose a VLL service and click Properties. The Epipe Service (Edit) form opens.
|
3 |
On the service tree, expand Sites→Spoke SDP Bindings, right-click and choose Create SDP Spoke Binding, or expand Spoke SDP Bindings, right-click on a spoke SDP binding and choose Properties. The Spoke SDP Binding (Create|Edit) form opens.
|
4 |
Specify a destination NE for the spoke SDP binding:
-
If the destination NE is a managed NE, select an NE from a list of managed NEs.
-
If the destination NE is an unmanaged NE, specify the system ID for the Tunnel Termination Site parameter.
|
5 |
Configure the required general parameters.
The range of the Ingress Label parameter depends on the parameter value set for the Static Label Range on the MPLS instance. See
To configure an MPLS instance .
|
6 |
Configure the L2TPv3 transport tunnel.
-
Select an L2TPv3 transport tunnel in the Tunnel panel. See
To configure an L2TPv3 service tunnel for more information about how to create an L2TPv3 tunnel.
-
Configure the parameters in the L2TPv3 Cookie panel.
|
7 |
To configure QoS:
-
Click on the QoS tab.
-
Select a network policy and configure the required parameters in the Forwarding Plane Redirect panel.
-
Select an ingress queue group template policy in the Forwarding Plane Redirect panel.
-
Configure the Instance ID parameter in the Forwarding Plane Redirect panel.
-
Select a network policy and configure the required parameters in the Port Redirect panel.
-
Select an egress queue group template policy in the Port Redirect panel.
-
Configure the Instance ID parameter in the Port Redirect panel.
|
8 |
Click on the States tab and configure the Administrative State parameter.
|
9 |
To configure pseudowire OAM:
-
Click on the Pseudowire OAM tab.
-
Configure the Control Word parameter.
If you are creating a spoke SDP binding using an MPLS-TP service tunnel for pseudowire static configuration, you must set the Control Word parameter to Preferred.
For Apipes, if you set the VC Type parameter to ATM-SDU in
Step 3 of
To create a VLL service , you must set the Control Word parameter to Preferred.
For Fpipes, if you set the VC Type parameter to FR-DLCI in
Step 3 of
To create a VLL service , you must set the Control Word parameter to Preferred.
For Hpipes, if you set the VC Type parameter to HDLC in
Step 3 of
To create a VLL service , you must set the Control Word parameter to Preferred.
|
10 |
To assign ingress and egress filter policies to the spoke SDP binding:
-
Click on the ACL tab.
-
Select an ingress filter in the Ingress Filter panel.
-
Select an egress filter in the Egress Filter panel.
-
Select an IPv6 ingress filter in the IPv6 Ingress Filter panel.
|
11 |
To assign an accounting policy to the SDP binding:
-
Click on the Accounting tab.
-
Configure the Collect Accounting Statistics parameter.
-
Select an accounting policy in the Accounting policy panel.
|
12 |
To configure security:
-
Click on the Security tab.
-
Enable the IP Src Monitoring parameter.
|
13 |
To assign an Application Profile to the spoke SDP binding:
-
Click on the Application Assurance tab.
-
Select an application profile string.
You can select only local profiles on the NE.
-
To associate an AA transit prefix policy with the service object, select a transit prefix policy in the Transit Prefix Policy panel.
See
To configure an AA transit prefix policy for more information about how to configure a transit prefix policy.
|
14 |
Save the changes and close the forms.
End of steps |