To configure IPoE hosts on a local user database

Steps
 
1 

Choose Manage→Residential Subscribers from the NFM-P main menu. The Manage Residential Subscribers form opens.

2 

Choose Local User Database (Local User DB) and click Search.

3 

Select a local user database entry and click Properties. The Local User Database (Edit) form opens.

4 

Click on the IPoE tab and configure the Match Type IPoE parameters.

You cannot set two parameters to the same value.

5 

Click on the Circuit ID Mask tab and configure the required parameters.

6 

Click on the Masks tab.

  1. Click Create or select an existing IPoE mask entry and click Properties. The Local User Database IPoE Mask form opens.

  2. Configure the required parameters.

  3. Save your changes and close the form.

7 

Click on the Hosts tab.

  1. Click Create or select an existing host entry and click Properties. The Local User Database IPoE Host (Create|Edit) form opens.

  2. Configure the required parameters.

  3. Select a diameter application policy.

  4. Select a subscriber authentication policy.

    If you are using LLID pre-authentication, choose a subscriber authentication policy that is associated with the pre-authentication server.

  5. Select a diameter authentication policy.

  6. Select a RIP policy.

  7. In the MSAP Defaults panel, select the following objects:

    • MSAP policy

    • MSAP service ID

    • MSAP group interface

    You can also specify an MSAP group interface by manually typing its name. If the port ID is not included in the typed name, set one of the following parameters to Port ID, depending on whether the port ID is to be the prefix or suffix of the group interface name:

    • MSAP Group Interface Prefix

    • MSAP Group Interface Suffix

  8. Select a RADIUS accounting policy and a duplicate RADIUS accounting policy.

  9. Configure IPv6 lease times for the IPoE host, if required.

    The Valid Life and Preferred Life parameters can be set to infinite by placing check marks in the Infinite check boxes.

8 

Click on the Address tab.

  1. Configure the required parameters.

  2. If you configure IPv6 parameters, select an IPv6 SLAAC prefix pool.

    You can also manually type an IPv6 SLAAC prefix pool name.

9 

Click on the Host Identification tab.

  1. Configure up to four of the following parameter groups.

    • Circuit ID Format, Circuit ID

    • MAC Address

    • Option 60 Format, Option 60

    • Remote ID Format, Remote ID

    • SAP ID

    • Service ID

    • IPoE String

    • System ID

    • Derived ID

    • IP Address Prefix, Prefix Length

  2. If one of the match criteria specified in Step 4 is Encapsulation Tag Range, configure the Type parameter.

    Configure the following parameters to define the outer encapsulation range:

    • Outer Start Value (Tag1)

    • Outer End Value (Tag1)

  3. If you set the Type parameter to Q in Q, configure the following parameters to define the inner encapsulation range:

    • Inner Start Value (Tag2)

    • Inner End Value (Tag2)

10 

Click on the Identification Strings tab.

  1. Configure the Option Number parameter. The form displays additional parameters.

  2. Configure the required identification strings parameters.

11 

Click on the WPP tab to configure WPP-based host authentication.

  1. Configure the Routing Instance parameter.

  2. If you specify the VPRN option in 1, you must configure the VPRN Service parameter. You can manually type a VPRN service ID, or select a VPRN service.

  3. Configure the Portal Name parameter. You can manually type a portal name, or select a WPP portal.

  4. Configure the Initial Subscriber Profile parameter. You can manually type a subscriber profile name, or select a subscriber profile.

  5. Configure the Initial SLA Profile parameter. You can manually type an SLA profile name, or select an SLA profile.

  6. Configure the Initial Application Profile parameter. You can manually type an application profile name, or select an application profile.

  7. Configure the Restore Default Profile On Disconnection parameter.

12 

Click on the Options tab.

13 

To configure IPv4 options, perform the following steps:

  1. Click Create or select an existing IPv4 option entry and click Properties. The Local User Database DHCP IPv4 Option (Create|Edit) form opens.

  2. Configure the Option parameter.

  3. Configure any additional parameters that appear. The configurable parameters vary, depending on the Option parameter value.

  4. Save your changes and close the form.

14 

Click on the IPv6 tab to configure IPv6 options.

  1. Click Create or select an existing IPv4 option entry and click Properties. The Local User Database DHCP IPv6 Option (Create|Edit) form opens.

  2. Configure the required IPv6 address parameters.

  3. Save your changes and close the form.

15 

Click on the RADIUS Proxy Cache tab to configure a RADIUS proxy cache for the IPoE host.

  1. Configure the Routing Instance parameter.

  2. If you set the Routing Instance parameter to Base, select a RADIUS proxy server.

  3. If you set the Routing Instance parameter to VPRN, select a VPRN service.

  4. Configure the Match Type parameter.

  5. Configure any additional parameters that appear. The configurable parameters vary, depending on the Match Type parameter value.

  6. Configure the Match Failure Action parameter.

16 

Click on the To Client Options tab to configure relay to client options for the IPoE host.

  1. Click Create or select an existing options instance and click Properties. The To Client Options (Create|Edit) form opens.

  2. Configure the required parameters.

  3. Configure any additional parameters that appear in the Option Value panel. The configurable parameters vary, depending on the Type parameter value.

  4. Save your changes and close the form.

17 

Save your changes and close the forms.

End of steps