Feature and Capacity Inventory report

Feature and Capacity Inventory report overview

The Feature and Capacity Inventory report consists of feature inventory and capacity inventory tables.

The feature inventory table counts the following items for the selected snapshot date:

radios
radio types
MSS types
features
NEs

ref radios
difference of radios
ref nodes
difference of nodes

The capacity inventory table lists the UBT or MPT type, its capacity and number of radios, number of ref radios, and difference of radios for the selected snapshot date.

You can compare the selected snapshot date against another snapshot to display the difference between the two snapshots.

Use cases

Capacity planning—Use the report to examine capacity and features which are licensed.

Limitations

When using a reference snapshot that contains data for features or capacities that are absent from any of the selected snapshot dates, rows in the table output may appear malformed (for example, displaying N/A in the Snapshot Date column).

Prerequisites

Before a feature and capacity inventory report can be created, the Wavence NE and ports must be discovered using NSP Classic management, and features and capacity must be scheduled.

Calculations

This section describes how the capacity and feature license values are calculated for this report. The following table lists the port feature licenses and the requirements for a port to be counted as using the licensed feature. If a feature is enabled on any channel, then the port is counted as using that feature, except where noted.

License	Description
XPIC	Number of ports with XPIC enabled
modAdp	Number of ports with Adaptive Modulation enabled
HCS	Number of ports with channel spacing igreater than 500MHz
HQAM	Number of ports using HQAM. The threshold depends on the UBT UBT-m: 128QAM/256QAM UBT-S, UBT-T: 2048QAM/4096QAM UBT-C is not included.
PTB	Number of ports with Packet Throughput Booster enabled
AES	Number of ports with AES Encryption enabled
TRX2	Number of ports using TRX2. UBT-T are counted only if both channels are enabled
TDM2Eth	Only UBT ports which are part of a CrossConnect backhaul service with a CEM to Eth profile are counted. If the same port is used in two different services, it will be counted twice.
CA	Total number of LAG members. Port usage is calculated using the primary port in the LAG. MPTs are also considered.

The following table lists the node feature licenses, and the requirements for a node to be counted as using the licensed feature.

License	Description
L3VPN	Total number of sites used for an L3 service, grouped by node type.
Ring	Number of ring instances created, grouped by node type.
1588TC	Number of nodes with 1588TC enabled
1588BC	Number of nodes with 1588BC enabled
IGP	Number of nodes with an OSPF Site that has an administrative state of Up
BNM	Number of nodes with one or more BNM entries enabled.
Core Protection	Number of nodes with core card protected.
RTU Synchronous Ethernet	Number of nodes with Sync-E enabled.
10G	Number of nodes containing a UBT port with speed 10G.

The following table lists the capacity licenses for each UBT type and capacity range.

UBT Type	From	Till	License
UBT-m	0	1000	yyCapU1000
UBT-m	1001	1500	yyCapU1500
UBT-m	1501	2000	yyCapU2000
UBT-m	2001	3000	yyCapU3000
UBT-m	3001	4000	yyCapU4000
UBT-m	4001	5000	yyCapU5000
UBT-m	5001	6000	yyCapU6000
UBT-m	6001	Above	yyCapU10000
UBT-S	0	50	yyCapU0050
UBT-S	51	100	yyCapU0100
UBT-S	101	160	yyCapU0160
UBT-S	161	200	yyCapU0200
UBT-S	201	300	yyCapU0300
UBT-S	301	400	yyCapU0400
UBT-S	401	600	yyCapU0600
UBT-S	601	800	yyCapU0800
UBT-S	801	Above	yyCapU1000
UBT-T	0	300	yyCapU0300
UBT-T	301	400	yyCapU0400
UBT-T	401	600	yyCapU0600
UBT-T	601	800	yyCapU0800
UBT-T	801	1000	yyCapU1000
UBT-T	1001	1500	yyCapU1500
UBT-T	1501	Above	yyCapU2000
UBT-C	0	50	yyCapU0050
UBT-C	51	100	yyCapU0100
UBT-C	101	160	yyCapU0160
UBT-C	161	200	yyCapU0200
UBT-C	201	300	yyCapU0300
UBT-C	301	400	yyCapU0400
UBT-C	401	600	yyCapU0600
UBT-C	601	800	yyCapU0800
UBT-C	801	Above	yyCapU1000

Report characteristics

The following table lists the principal report characteristics.

Table 15-4: Feature and Capacity Inventory report characteristics

Characteristic	Value
Source database	NSP database
NE types supported	Wavence MSS-1, Wavence MSS-4, Wavence MSS-8, Wavence MSS-E, Wavence MSS-HE, Wavence MSS-XE, Wavence MSS-O, Wavence UBT-SA, Wavence UBT-I, Wavence UBT-T XP, Wavence-SA, Wavence NIM
NE types supported	Support is limited to NEs found in the network.
Report inputs	Prompt	Notes
	Snapshot date	Calendar date or relative date (for example, two days ago) and time. Do not specify more than ten snapshot dates.
	Reference snapshot date	Snapshot date to compare the selected snapshot against
	Logo Resource ID	The logo to add to the report. Enter the Resource ID of the logo image in the Images folder. The default is the Nokia logo. To create the report without a logo, leave the Logo Resource ID field blank.
	Logo Position	Choose Left, Middle, or Right. The logo appears on the left on the first page of the report if you choose Left or Middle.
	Show report output on one page	Select the check box to enable pagination. Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.
	Apply	Applies all the parameters and prepares the report based on the parameters entered.
	Reset	Resets all the parameters to default value.
Drill-down support	No

Example

The following figure shows a report example using a single snapshot date.

Figure 15-4: Feature and Capacity Inventory report

The following figure shows a report example using a reference snapshot date.