Interface Utilization Details report

Interface Utilization Details report overview

The Interface Utilization Details report shows utilization details for a selected IGP interface. The report can be run on its own or as a drill-down from a Link Utilization report.

The default display is a set of graphs and a table showing ingress, egress utilization, reference speeds, and percentage interface consumption. By default the table is sorted by average egress interface consumption in decreasing value order (worst first).

Percentage interface consumption is based on average MPLS interface throughput divided by average LSP throughput.

The results in the table are colored based on interface consumption percentage ranges:

green: 0% to 20%
turquoise: 21% to 40%
blue: 41% to 60%
purple: 61% to 80%
red: 81% to 100%

Use cases

Capacity planning—Use the report to examine interface utilization patterns for planning future capacity requirements.

Limitations

Minimum and maximum throughput aggregation cannot be compared with the minimum and maximum throughput values generated from raw granularity.

Prerequisites

For an Interface Utilization Details Report to be created for an interface, the Prerequisites for a Link Utilization report must be performed.

To view the report for granularities other than raw data, the aggregation rules must be enabled; see How do I configure analytics aggregation?. The following table describes the aggregation rules and the accounting policies that must be configured for the NEs on which statistics are to be collected; see the NSP NFM-P Statistics Management Guide for information about configuring an accounting policy.

Table 14-29: Interface Utilization Details report prerequisites

Aggregator name	Monitored object class	Statistics class	Statistics collection	Details (MIB name)	NE types
Ip Interface Stats Aggregator	rtr.Network Interface	rtr.IpInterfaceStats	Performance statistics	vRtrIfStatsEntry	7250 IXR 7750 SR Note: 7210 SAS is not supported
Ip Interface Additional Stats Aggregator	rtr.Network Interface	rtr.IpInterfaceAdditionalStats	Performance statistics	vRtrIfStatsExtEntry	7250 IXR 7750 SR Note: 7210 SAS is not supported
SAR Ip Interface Stats Aggregator	rtr.Network Interface	rtr.SarIpInterfaceStats	Performance statistics	—	7705 SAR 7705 SAR Hm Note: 7210 SAS is not supported
Mpls Interface Stats Aggregator	rtr.Network Interface	mpls.MplsInterfaceStats	Performance statistics	vRtrMplsIfStatEntry	7210 SAS 7250 IXR 7705 SAR 7705 SAR Hm 7750 SR Omnisystem NEs
MPLS LSP Egress Stats Aggregator	rtr.Network Interface	mpls.MplsLspEgressStats	Performance statistics	—	7705 SAR 7705 SAR Hm 7750 SR Note: 7210 SAS is not supported

Report characteristics

The following table lists the principal report characteristics.

Table 14-30: Interface Utilization Details report characteristics

Characteristic	Value
Data type	Statistics
Source database	Auxiliary database
Interface types supported	IP (IS-IS, OSPF, RIP), MPLS
Report inputs	Prompt	Notes
	End date	Calendar date or relative date (for example, two days ago) and time
	Granularity	Aggregation types: None (raw data) Hourly Daily Monthly
	Report Range	Length of time to be reported, in minutes (minutes, min), hours (hours, h), days (days, d), or months (months, m)
	Node Type	Search using partial names or wildcard (%). Select individual items or click Select All.
	Node Name (or Node Name Pattern)
	Nodes
	Interface Name (or Interface Name Pattern)
	Interfaces
	Rank	Value to use for the Top-N LSPs. Max is 1000, default is 10.
	Reference Speed	Interface Speed or Physical Port Speed Notes: IP-only utilization can be calculated with Interface Speed. MPLS-only and IP+MPLS calculations can only be calculated if the Reference Speed is Physical Port Speed.
	Logo Resource ID	The logo to add to the report. Enter the Resource ID of the logo image in the Images folder. The default is the Nokia logo. To create the report without a logo, leave the Logo Resource ID field blank.
	Logo Position	Choose Left, Middle, or Right. The logo appears on the left on the first page of the report if you choose Left or Middle.
	Show report output on one page	Select the check box to enable pagination. Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.
Drill-down support	Yes—OpenClick on a Name to launch a Service Utilization per LSP report.

Example

The following figures show a report example.