Choose Policies→Residential Subscriber from the NFM-P main menu. The Residential Subscriber Policies form opens.

CAUTION Service Disruption

Modifying an active SLA profile is potentially service-affecting.

Ensure that you consider the implications of reconfiguring the SLA profile before you proceed.

Click Create→SLA Profile or choose an existing SLA Profile entry and click Properties. The SLA Profile (Create|Edit) form opens.

Configure the required parameters.

The Displayed Name parameter is configurable only during SLA profile creation.

Select a credit control policy to associate with the SLA profile.

Click on the QoS tab to associate ingress and egress QoS policies with the SLA profile.

1. Select an access ingress policy to associate with the SLA profile.

2. Configure the required ingress parameters.

3. Select an access egress policy to associate with the SLA profile.

4. Select a scheduler policy to associate with the SLA profile.

5. Configure the required egress parameters.

Click on the ACL tab to associate ingress or egress IP filters with the SLA profile. Select any of the following filters:

• ingress IP filter

• egress IP filter

• ingress IPv6 filter

• egress IPv6 filter

• one-time HTTP redirect filter

Click on the Supported Service Models tab to specify the intended service model(s) for the SLA profile.

Click on the Category Map tab.

1. Select a category map to associate with the SLA profile.

   If you selected a credit control policy in Step 4, you will not be able to select a category map.

2. Click Create or choose a category entry and click Properties. The Category (Create|Edit) form opens.

3. Select a category name and configure the Idle Timeout parameter.

   Note:

   The session will be disconnected if the value of the Activity Threshold parameter is not met during the period specified by the Idle Timeout parameter. See To configure a category map policy for information about configuring the Activity Threshold parameter.

4. Save your changes and close the form.

Click on the Bonding Selection tab to configure the SLA profile for use in a connection bonding configuration.

Configure the required selection bonding parameters.

Click on the Host Limits tab to specify a maximum host count for the SLA profile.

You can set an overall limit, or configure host limits at a more granular level for each of the IPv4, IPv6, and L2TP host type categories, and their respective subcategories.

Although the NFM-P specifies a Host Limit parameter range of 1-131071, the maximum host limit varies for different NE types and chassis types.

Click on the Override Policy Items tab to specify local overrides for queue parameters of the QoS policies assigned to the SLA profile.

On the Access Ingress Queues tab, click Create or choose an ingress queue override item and click Properties. The Access Ingress Queue Override (Create|Edit) form opens.

1. Select an access ingress policy queue.

2. Click on the Override tab and configure the required parameters.

3. Save your changes and close the form.

On the Access Egress Queues tab, click Create or choose an egress queue override item and click Properties. The Access Egress Queue Override (Create|Edit) form opens.

1. Select an access egress policy queue.

2. Click on the Override tab and configure the required parameters.

3. Configure overridden HS queue parameters and select an override slope policy in the HS WRED Queue, if required.

4. Save your changes and close the form.

On the Access Ingress Policer tab, click Create or choose an ingress policer override item and click Properties. The Ingress Policer Override (Create|Edit) form opens.

1. Select an access ingress policy policer.

2. Click on the Override tab and configure the required parameters.

3. Save your changes and close the form.

On the Access Egress Policer tab, click Create or choose an egress policer override item and click Properties. The Egress Policer Override (Create|Edit) form opens.

1. Select an access egress policy policer.

2. Click on the Override tab and configure the required parameters.

3. Save your changes and close the form.

On the Egress Scheduler tab, specify local overrides for traffic flow rate parameters of the egress schedulers assigned to the SLA profile.

1. Click Create or choose an egress scheduler override item and click Properties. The Egress Scheduler Override (Create|Edit) form opens.

2. Select the scheduler policy you want to override.

3. Click on the Override tab and configure the required parameters.

   The CIR parameter is available only when the Summed CIR parameter is set to False.

4. Save your changes and close the form.

On the HS WRR Groups tab, specify local overrides for traffic flow rate parameters of the egress schedulers assigned to the SLA profile.

1. Click Create or choose an HS WRR group override item and click Properties. The HS WRR Group Override (Create|Edit) form opens.

2. Select an HS WRR group.

3. Click on the Override tab and configure the required parameters.

4. Save your changes and close the form.

Click OK to save the policy and close the form, or click Apply to save the policy. See To release and distribute a policy to distribute the policy to NEs.

End of steps