For feedback, use the following:
ipd_online_feedback@alcatel-lucent.com
Table of Contents Previous Next Index PDF

PBB Show Commands
PBB
eth-cfm
Syntax 
eth-cfm
Context 
show
Description 
This command displays 802.1ag CFM information.
association
Syntax 
association [ma-index] [detail]
Context 
show>eth-cfm
Description 
Shows association information.
Parameters 
ma-index
Specifies the MA index value.
Values
1 — 4294967295
detail
Displays all association detail.
Output 
*A:alcag1-R6# show eth-cfm association 
======================================================================
CFM Association Table
======================================================================
Md-index   Ma-index   Name                     CCM-interval Bridge-id          
----------------------------------------------------------------------
1          1          ivpls                    1            5000      
======================================================================
*A:alcag1-R6#
cfm-stack-table
Syntax 
cfm-stack-table
cfm-stack-table port [port-id> [vlan vlan-id]] [level 0..7] [direction up | down]
cfm-stack-table sdp [sdp-id[:vc-id]>] [level 0..7]] [direction up | down]
cfm-stack-table virtual [service-id] [level 0..7]
Context 
show>eth-cfm
Description 
Summarizes all MEPs/MIPs.
Parameters 
port-id
Displays information about the specified port.
Values
port-id slot/mda/port[.channel]
lag-id lag-id
 lag keyword
id 1 — 200
sdp-id[:vc-id]
Specfies an existing SDP and VC ID.
Values
1 — 17407
vlan-id
Specifies te VLAN ID.
Values
0 — 4094
level
Specifies the level.
Values
0 — 7
direction up | down
Indicates the direction in which the maintenance association (MEP or MIP) faces on the bridge port.
down — Displays continuity check information configured away from the MAC relay entity.
up — Displays continuity check information configured toward the MAC relay entity.
service-id
Specifies information about the specified service ID.
Values
1 — 2147483648
Sample Output
*A:alcag1-R6# show eth-cfm cfm-stack-table 
========================================================================
CFM SAP Stack Table
========================================================================
Sap            Level Dir  Md-index   Ma-index   Mep-id Mac-address             
------------------------------------------------------------------------
1/2/9:5        4     Up   1          1          51     00:ae:ae:ae:ae:ae
========================================================================
CFM SDP Stack Table
========================================================================
Sdp            Level Dir  Md-index   Ma-index   Mep-id Mac-address             
------------------------------------------------------------------------
No Matching Entries
========================================================================
*A:alcag1-R6#
domain
Syntax 
domain [md-index] [association ma-index | all-associations [detail]]
Context 
show>eth-cfm>domain
Description 
This command displays domain information.
Parameters 
md-index
Specifies the maintenance domain (MD) index value.
Values
1 — 4294967295
ma-index
Specifies the MA index value.
Values
1 — 4294967295
all-associations
Displays information all maintenance associations.
detail
Displays detailed information.
Sample Output
*A:alcag1-R6# show eth-cfm domain 
==============================================================================
CFM Domain Table
==============================================================================
Md-index   Level Name                                       Format             
------------------------------------------------------------------------------
1          4     ivpls                                      charString        
==============================================================================
*A:alcag1-R6#
 
*A:alcag1-R6# show eth-cfm mep 51 domain 1 association 1 
-------------------------------------------------------------------------------
Mep Information
-------------------------------------------------------------------------------
Md-index           : 1                        Direction         : Up           
Ma-index           : 1                        Admin             : Enabled      
MepId              : 51                       CCM-Enable        : Enabled      
IfIndex            : 38043648                 PrimaryVid        : 5            
FngState           : fngReset                                                  
LowestDefectPri    : allDef                   HighestDefect     : none         
Defect Flags       : None
Mac Address        : 00:ae:ae:ae:ae:ae        CcmLtmPriority    : 7            
CcmTx              : 775                      CcmSequenceErr    : 0            
CcmLastFailure Frame:
    None
XconCcmFailure Frame:
    None
*A:alcag1-R6#
mep
Syntax 
mep mep-id domain md-index association ma-index [loopback] [linktrace]
Context 
show>eth-cfm>domain
Description 
This command displays Maintenance Endpoint (MEP) information.
Parameters 
mep-id
Specifies the maintenance association end point identifier.
Values
1 — 8191
md-index
Specifies the maintenance domain (MD) index value.
Values
1 — 4294967295
ma-index
Specifies the MA index value.
Values
1 — 4294967295
loopback
Displays loopback information for the specified MEP.
linktrace
Displays linktrace information for specified MEP.
Sample Output
*A:alcag1-R6# oam eth-cfm loopback 00:af:af:af:af:af mep 51 domain 1 association 1 
eth-cfm Loopback Test Initiated: Mac-Address: 00:af:af:af:af:af, out sap: 1/2/9:5
Sent 1 packets, received 1 packets [0 out-of-order, 0 Bad Msdu] -- OK
*A:alcag1-R6#
 
 
*A:alcag1-R6# oam eth-cfm linktrace 00:af:af:af:af:af mep 51 domain 1 association 1 
Index Ingress Mac          Egress Mac           Relay      Action    
----- -------------------- -------------------- ---------- ----------
1     00:00:00:00:00:00    00:AF:AF:AF:AF:AF    rlyHit     terminate 
----- -------------------- -------------------- ---------- ----------
No more responses received in the last 5 seconds.
*A:alcag1-R6#
i-vpls
Syntax 
i-vpls
Context 
show>service>id
Description 
Displays I-VPLS services associated with the B-VPLS service. This command only applies when the service is a B-VPLS.
Sample Output
*A:SetupCLI# show service id 2002 i-vpls 
================================================================
Related iVpls services for bVpls service 2002
================================================================
iVpls SvcId         Oper ISID           Admin               Oper
-------------------------------------------------------------------------------
2001                122                 Up                  Down
-------------------------------------------------------------------------------
Number of Entries : 1
-------------------------------------------------------------------------------
*A:alcag1-R6#
*A:term17>show>service>id# i-vpls
===============================================================================
Related iVpls services for bVpls service 2000
===============================================================================
iVpls SvcId         Oper ISID           Admin               Oper
-------------------------------------------------------------------------------
2100                2100                Up                  Up
2110                123                 Up                  Up
-------------------------------------------------------------------------------
Number of Entries : 2
-------------------------------------------------------------------------------
*A:SetupCLI#
base
Syntax 
base
Context 
show>service>pbb
Sample
*A:Dut-B# show service pbb base 
======================================================================
PBB MAC Information
======================================================================
MAC-Notif Count : 3
MAC-Notif Interval : 1
Source BMAC : Default
======================================================================
mac-name
Syntax 
mac-name [detail]
Context 
show>service>pbb
Description 
This command displays information on a specific MAC name.
Sample
*A:Dut-B# show service pbb mac-name 
=====================================================================
MAC Name Table
=====================================================================
MAC-Name MAC-Address
---------------------------------------------------------------------
test 00:03:03:03:03:02
=====================================================================
*A:Dut-B# show service pbb mac-name test detail 
=====================================================================
Services Using MAC name='test' addr='00:03:03:03:03:02'
=====================================================================
Svc-Id ISID
---------------------------------------------------------------------
501 501
---------------------------------------------------------------------
Number of services: 1
=====================================================================
*A:Dut-B#
id
Syntax 
id service-id
Context 
show>service
Description 
This command displays information on a specific service ID.
Sample
*A:Dut-B# show service id 1 all 
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : b-VPLS
Description : (Not Specified)
Customer Id : 1
Last Status Change: 05/17/2009 19:33:11
Last Mgmt Change : 05/17/2009 19:31:59
Admin State : Up Oper State : Up
MTU : 2000 Def. Mesh VC Id : 1
SAP Count : 1 SDP Bind Count : 0
Snd Flush on Fail : Disabled Host Conn Verify : Disabled
Propagate MacFlush: Disabled
Oper Backbone Src : 00:03:00:00:04:01 Use SAP B-MAC : enabled 
i-Vpls Count : 0
Epipe Count : 900
*A:Dut-B# show service id 501 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 501 Vpn Id : 0
Service Type : Epipe
Description : (Not Specified)
Customer Id : 1
Last Status Change: 05/17/2009 19:41:32
Last Mgmt Change : 05/17/2009 19:40:03
Admin State : Up Oper State : Up
MTU : 1514
Vc Switching : False
SAP Count : 1 SDP Bind Count : 0
-------------------------------------------------------------------------------
PBB Tunnel Point
-------------------------------------------------------------------------------
B-vpls Backbone-dest-MAC Isid AdmMTU OperState Flood Oper-dest-MAC
-------------------------------------------------------------------------------
1 test 501 2000 Up Yes 00:03:03:03:03:02
-------------------------------------------------------------------------------
*A:Dut-B#
mrp
Syntax 
mrp
Context 
show>service>id
Description 
This command displays information on a a per service MRP configuration.
Output 
*A:PE-A# show service id 10 mrp
-------------------------------------------------------------------------------
MRP Information
-------------------------------------------------------------------------------
Admin State        : Up                 Failed Register Cnt: 0
Max Attributes     : 2048               Attribute Count    : 10
Flood Time         : Off
-------------------------------------------------------------------------------
*A:PE-A#
mrp-policy
Syntax 
mrp-policy [mrp-policy]
mrp-policy mrp-policy [association]
mrp-policy mrp-policy [entry entry-id]
Context 
show>service
Description 
This command displays MRP policy information.
Parameters 
mrp-policy
Specifies the MRP policy.
Values
32 chars max
entry-id
Specifies the entry ID.
Values
1..65535
mmrp
Syntax 
mmrp mac [ieee-address]
Context 
show>service>id
Description 
This command displays information on MACs. If a MAC address is specified, information will be displayed relevant to the specific group. No parameter will display information on all group MACs on a server.
Parameters 
ieee-address
Hex string: xx:xx:xx:xx:xx:xx: or xx-xx-xx-xx-xx-xx
Output 
*A:PE-A# show service id 10 mmrp mac 01:1E:83:00:00:65
-------------------------------------------------------------------------------
SAP/SDP                                 MAC Address       Registered  Declared
-------------------------------------------------------------------------------
sap:1/1/4:10                            01:1e:83:00:00:65 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:65 No          Yes
sap:2/2/5:10                            01:1e:83:00:00:65 Yes         Yes
-------------------------------------------------------------------------------
*A:PE-A#
 
*A:PE-A# show service id 10 mmrp mac
-------------------------------------------------------------------------------
SAP/SDP                                 MAC Address       Registered  Declared
-------------------------------------------------------------------------------
sap:1/1/4:10                            01:1e:83:00:00:65 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:66 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:67 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:68 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:69 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6a No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6b No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6c No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6d No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6e No          Yes
sap:1/2/2:10                            01:1e:83:00:00:65 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:66 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:67 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:68 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:69 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6a No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6b No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6c No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6d No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6e No          Yes
sap:2/2/5:10                            01:1e:83:00:00:65 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:66 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:67 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:68 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:69 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6a Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6b Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6c Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6d Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6e Yes         Yes
-------------------------------------------------------------------------------
*A:PE-A#
spb
Syntax 
spb
Context 
clear>service>id
Description 
This command clears STP related data.
adjacency
Syntax 
adjacency [detail]
Context 
show>service>id>spb
Description 
This command displays SPB adjacency information.
Parameters 
detail
Show detailed information.
Output 
Sample Ouput
===============================================================================
ISIS Adjacency
===============================================================================
System ID                Usage State Hold Interface                     MT Enab
-------------------------------------------------------------------------------
Dut-B                    L1    Up    19   sap:1/2/2:1.1                 No
Dut-C                    L1    Up    21   sap:1/2/3:1.1                 No
-------------------------------------------------------------------------------
Adjacencies : 2
===============================================================================
base
Syntax 
base
Context 
show>service>id>spb
Description 
This command displays SPB base information.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb base
===============================================================================
Service SPB Information
===============================================================================
Admin State        : Up                 Oper State         : Up
ISIS Instance      : 1024               FID                : 1
Bridge Priority    : 8                  Fwd Tree Top Ucast : spf
Fwd Tree Top Mcast : st
Bridge Id          : 80:00.00:10:00:01:00:01
Mcast Desig Bridge : 80:00.00:10:00:01:00:01
 
===============================================================================
ISIS Interfaces
===============================================================================
Interface                        Level CircID  Oper State   L1/L2 Metric
-------------------------------------------------------------------------------
sap:1/2/2:1.1                    L1    65536   Up           10/-
sap:1/2/3:1.1                    L1    65537   Up           10/-
-------------------------------------------------------------------------------
Interfaces : 2
===============================================================================
FID ranges using ECT Algorithm
-------------------------------------------------------------------------------
1-99      low-path-id
100-100   high-path-id
101-4095  low-path-id
===============================================================================
database
Syntax 
database
Context 
show>service>id>spb
Description 
This command displays SPB database information.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb database
===============================================================================
ISIS Database
===============================================================================
LSP ID                                  Sequence  Checksum Lifetime Attributes
-------------------------------------------------------------------------------
 
Displaying Level 1 database
-------------------------------------------------------------------------------
Dut-A.00-00                             0xc       0xbaba   1103     L1
Dut-B.00-00                             0x13      0xe780   1117     L1
Dut-C.00-00                             0x13      0x85a    1117     L1
Dut-D.00-00                             0xe       0x174a   1119     L1
Level (1) LSP Count : 4
===============================================================================
fate-sharing
Syntax 
fate-sharing
Context 
show>service>id>spb
Description 
This command displays SPB fate-sharing information on User B-VPLS service, in correspond to associated Control B-VPLS service.
Output 
Sample Ouput
*A:Dut-A# Node show service id spb fate-sharing
===============================================================================
User service fate-shared sap/sdp-bind information
===============================================================================
Control   Control Sap/             FID       User      User Sap/
SvcId     SdpBind                            SvcId     SdpBind
-------------------------------------------------------------------------------
500       1/1/20:500               502       502       1/1/20:502
===============================================================================
fdb
Syntax 
fdb
Context 
show>service>id>spb
Description 
This command displays SPB Forwarding database information.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb fdb
==============================================================================
User service FDB information
==============================================================================
MacAddr           UCast Source          State   MCast Source          State
------------------------------------------------------------------------------
00:10:00:01:00:02 1/2/2:1.1             ok      1/2/2:1.1             ok
00:10:00:01:00:03 1/2/3:1.1             ok      1/2/3:1.1             ok
00:10:00:01:00:04 1/2/2:1.1             ok      1/2/2:1.1             ok
------------------------------------------------------------------------------
Entries found: 3
==============================================================================
fid
Syntax 
fid [fid] fate-sharing
fid [fid] user-service
fid [fid] fdb
fid [fid] mfib [group-mac ieee-address]
fid [fid] mfib [isid isid]
Context 
show>service>id>spb
Description 
This command displays SPBcontrol service FID information.
Parameters 
fid
A user service FID may be specified. All user service FIDs are displayed if the FID is not specified.
user-service
Specifies user VPLS information for each control VPLS per forwarding data-base identfier. A user service FID may be specified. All user service FIDs are displayed if the FID is not specified.
fdb
Specifies user VPLS Shortest Path Bridging (SPB) multicast forwarding data-base (Mfib) information.
mfib
group-mac ieee-address
Specifies the 48-bit IEEE 802.3 group MAC address.
isid isid
Specifies the value of ISID of the group MAC address of this entry.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb fid fate-sharing
===============================================================================
Control service fate-shared sap/sdp-bind information
===============================================================================
Control   Control Sap/             FID       User      User Sap/
SvcId     SdpBind                            SvcId     SdpBind
-------------------------------------------------------------------------------
500       1/1/20:500               502       502       1/1/20:502
=============================================================================== 
 
*A:Dut-A# show service id 100001 spb fid fdb
===============================================================================
Control service FDB information
===============================================================================
Fid        MacAddr            UCast Source             MCast Source
                              Last Update              Last Update
-------------------------------------------------------------------------------
1          00:10:00:01:00:01  local                    local
                              04/04/2012 15:11:24      04/04/2012 15:11:24
1          00:10:00:01:00:02  1/2/2:1.1                1/2/2:1.1
                              04/04/2012 15:51:45      04/04/2012 15:51:45
1          00:10:00:01:00:03  1/2/3:1.1                1/2/3:1.1
                              04/04/2012 15:51:56      04/04/2012 15:51:56
1          00:10:00:01:00:04  1/2/2:1.1                1/2/2:1.1
                              04/04/2012 15:52:11      04/04/2012 15:52:11
-------------------------------------------------------------------------------
Entries found: 4
===============================================================================
*A:Dut-A# show service id 100001 spb fid mfib
===============================================================================
Control service MFIB information
===============================================================================
FID   MacAddr           ISID      Source                   Last Update
-------------------------------------------------------------------------------
1     01:1E:83:00:27:11 10001     1/2/2:1.1                04/04/2012 15:51:45
                                  1/2/3:1.1                04/04/2012 15:51:56
                                  local                    04/04/2012 15:42:44
100   01:1E:83:00:27:12 10002     1/2/2:1.1                04/04/2012 15:51:45
                                  1/2/3:1.1                04/04/2012 15:51:56
                                  local                    04/04/2012 15:43:09
-------------------------------------------------------------------------------
Entries found: 6
===============================================================================
hostname
Syntax 
hostname
Context 
show>service>id>spb
Description 
This command displays SPB system-id to hostname mapping.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb hostname
===============================================================================
Hosts
===============================================================================
System Id                Hostname
-------------------------------------------------------------------------------
0000.00AA.AAAA           cses-B02
0000.00BB.BBBB           cses-B07
===============================================================================
interface
Syntax 
interface
Context 
show>service>id>spb
Description 
This command displays SPB interfaces.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb interface
===============================================================================
ISIS Interfaces
===============================================================================
Interface                        Level CircID  Oper State   L1/L2 Metric
-------------------------------------------------------------------------------
sap:1/1/20:500                   L1    65536   Up           10/-
-------------------------------------------------------------------------------
Interfaces : 1
===============================================================================
mfib
Syntax 
mfib [group-mac ieee-address][isid isid]
Context 
show service id <svcId> spb
Description 
This command displays multicast forwarding data-base information.
Parameters 
group-mac
Optional IEEE group MAC format:
mac-address: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx
isid
Optional I-SID.
Format: 0..16777215
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb mfib
===============================================================================
User service MFIB information
===============================================================================
MacAddr           ISID     Status
-------------------------------------------------------------------------------
01:1E:83:00:27:11 10001    Ok
-------------------------------------------------------------------------------
Entries found: 1
===============================================================================
routes
Syntax 
routes
Context 
show>service>id>spb
Description 
This command displays SPB route information.
Output 
Sample Ouput
*A:Dut-A# show service id 100001 spb routes
================================================================
MAC Route Table
================================================================
Fid  MAC                                          Ver.   Metric
      NextHop If                    SysID
----------------------------------------------------------------
 
Fwd Tree: unicast
----------------------------------------------------------------
1    00:10:00:01:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
1    00:10:00:01:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
1    00:10:00:01:00:04                            10     20
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
100  00:10:00:02:00:04                            10     20
      sap:1/2/3:1.1                 Dut-C
 
Fwd Tree: multicast
----------------------------------------------------------------
1    00:10:00:01:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
1    00:10:00:01:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
1    00:10:00:01:00:04                            10     20
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
100  00:10:00:02:00:04                            10     20
      sap:1/2/3:1.1                 Dut-C
----------------------------------------------------------------
No. of MAC Routes: 12
================================================================
 
================================================================
ISID Route Table
================================================================
Fid  ISID                                         Ver.
      NextHop If                    SysID
----------------------------------------------------------------
1    10001                                        10
      sap:1/2/2:1.1                 Dut-B
      sap:1/2/3:1.1                 Dut-C
100  10002                                        10
      sap:1/2/2:1.1                 Dut-B
      sap:1/2/3:1.1                 Dut-C
----------------------------------------------------------------
No. of ISID Routes: 2
================================================================ 
A:Dut-A#  show service id spb fate-sharing
===============================================================================
User service fate-shared sap/sdp-bind information
===============================================================================
Control   Control Sap/             FID       User      User Sap/
SvcId     SdpBind                            SvcId     SdpBind
-------------------------------------------------------------------------------
500       1/1/20:500               502       502       1/1/20:502
===============================================================================
spf
Syntax 
spf
Context 
show>service>id>spb
Description 
This command displays SPF information.
Output 
Sample Ouput
A:cses-B01#  show service id spb spf
===============================================================================
Path Table
===============================================================================
Node                            Interface                  Nexthop
-------------------------------------------------------------------------------
 
Fwd Tree: unicast,   ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00                	  sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
 
Fwd Tree: unicast,   ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00               	  sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
 
Fwd Tree: multicast,   ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00                	  sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
 
Fwd Tree: multicast,   ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00               	  sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
===============================================================================
spf-log
Syntax 
spf-log
Context 
show>service>id>spb
Description 
This command displays SPF Log information.
Output 
Sample Ouput
A:cses-B01#  show service id spb spf-log
===============================================================================
ISIS SPF Log
===============================================================================
When                 Duration       L1 Nodes   L2 Nodes   Event Count      Type
-------------------------------------------------------------------------------
07/23/2012 16:01:13  <0.01s         1          0          1                Reg
07/23/2012 16:01:19  <0.01s         1          0          4                Reg
07/23/2012 16:01:24  <0.01s         3          0          2                Reg
07/23/2012 16:01:29  <0.01s         4          0          1                Reg
-------------------------------------------------------------------------------
Log Entries : 4
-------------------------------------------------------------------------------
statistics
Syntax 
statistics
Context 
show>service>id>spb
Description 
This command displays SPB statistics.
Output 
Sample Ouput
A:cses-B01#  show service id spb statistics
===============================================================================
ISIS Statistics
===============================================================================
ISIS Instance     : 1024                    SPF Runs       : 4
Purge Initiated   : 0                       LSP Regens.    : 11
 
CSPF Statistics
Requests          : 0                       Request Drops  : 0
Paths Found       : 0                       Paths Not Found: 0
 
-------------------------------------------------------------------------------
PDU Type   Received   Processed  Dropped    Sent       Retransmitted
-------------------------------------------------------------------------------
LSP        31         31         0          9          0
IIH        532        532        0          533        0
CSNP       479        479        0          479        0
PSNP       9          9          0          27         0
Unknown    0          0          0          0          0
===============================================================================
status
Syntax 
status
Context 
show>service>id>spb
Description 
This command displays SPB status.
Output 
Sample Ouput
A:cses-B01#  show service id spb status
===============================================================================
ISIS Status
===============================================================================
System Id            : 0000.00AA.AAAA
Admin State          : Up
Oper State           : Up
SPB Routing          : Enabled
Last Enabled         : 07/23/2012 16:01:06
Level Capability     : L1
Authentication Check : True
Authentication Type  : None
CSNP-Authentication  : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication  : Enabled
Overload-On-Boot Tim*: 0
LSP Lifetime         : 1200
LSP Wait             : 5 sec (Max)   0 sec (Initial)   1 sec (Second)
LSP MTU Size         : 1492  (Config)  1492  (Oper)
Adjacency Check      : loose
L1 Auth Type         : none
L1 CSNP-Authenticati*: Enabled
L1 HELLO-Authenticat*: Enabled
L1 PSNP-Authenticati*: Enabled
L1 Preference        : 15
L1 Ext. Preference   : 160
L1 Wide Metrics      : Enabled
L1 LSDB Overload     : Disabled
L1 LSPs              : 4
L1 Default Metric    : 10
L1 IPv6 Def Metric   : 10
Last SPF             : 07/23/2012 16:01:29
SPF Wait             : 10 sec (Max)   1000 ms (Initial)   1000 ms (Second)
Multi-topology       : Disabled
Area Addresses       : 00
Total Exp Routes(L1) : 0
IID TLV              : Disabled
All-L1-MacAddr       : 01:80:c2:00:00:14
===============================================================================
 
PBB Clear Commands
counters
Syntax 
counters
Context 
clear>service>statistics>id
Description 
This command clears all traffic queue counters associated with the service ID.
mesh-sdp
Syntax 
mesh-sdp sdp-id[:vc-id] {all | counters |stp | mrp}
Context 
clear>service>statistics>id
Description 
This command clears the statistics for a particular mesh SDP bind.
Parameters 
sdp-id
Specifies the SDP ID for which to display information.
Default
All SDPs.
Values
1 — 17407
vc-id
Displays information about the virtual circuit identifier.
Values
1 — 4294967295
all
Clears all queue statistics and STP statistics associated with the SDP.
counters
Clears all queue statistics associated with the SDP.
stp
Clears all STP statistics associated with the SDP.
mrp
Clears all MRP statistics associated with the SDP.
mrp
Syntax 
mrp
Context 
clear>service>statistics>id
Description 
This command clears all MRP statistics for the service ID.
spoke-sdp
Syntax 
spoke-sdp sdp-id[:vc-id] {all | counters | stp| l2pt | mrp}
Context 
clear>service>statistics>id
Description 
This command clears statistics for the spoke SDP bound to the service.
Parameters 
sdp-id
The spoke SDP ID for which to clear statistics.
Values
1 — 17407
vc-id
The virtual circuit ID on the SDP ID to be reset.
Values
1 — 4294967295
all
Clears all queue statistics and STP statistics associated with the SDP.
counters
Clears all queue statistics associated with the SDP.
stp
Clears all STP statistics associated with the SDP.
l2pt
Clears all L2PT statistics associated with the SDP.
mrp
Clears all MRP statistics associated with the SDP.
sap
Syntax 
sap sap-id {all | counters | stp| l2pt | mrp}
Context 
clear>service>statistics>id
Description 
This command clears statistics for the SAP.
Parameters 
sap-id
The SAP ID for which to clear statistics.
all
Clears all queue statistics and STP statistics associated with the SAP.
counters
Clears all queue statistics associated with the SAP.
stp
Clears all STP statistics associated with the SAP.
l2pt
Clears all L2PT statistics associated with the SAP.
mrp
Clears all MRP statistics associated with the SAP.
stp
Syntax 
stp
Context 
clear>service>statistics>id
Description 
Clears all spanning tree statistics for the service ID.
 
PBB Debug Commands
mrp
Syntax 
[no] mrp
Context 
debug>service>id
Description 
This command enables and configures MRP debugging.
all-events
Syntax 
all-events
Context 
debug>service>id>mrp
Description 
This command enables MRP debugging for the applicant, leave all, periodic and registrant state machines and enables debugging of received and transmutted MRP PDUs.
applicant-sm
Syntax 
[no] applicant-sm
Context 
debug>service>id>mrp
Description 
This command enables debugging of the applicant state machine.
The no form of the command disables debugging of the applicant state machine.
leave-all-sm
Syntax 
[no] leave-all-sm
Context 
debug>service>id>mrp
Description 
This command enables debugging of the leave all state machine.
The no form of the command disables debugging of the leave all state machine.
mmrp-mac
Syntax 
[no] mmrp-mac ieee-address
Context 
debug>service>id>mrp
Description 
This command filters debug events and only shows events related to the MAC address specified.
The no form of the command removes the debug filter.
Parameters 
ieee-address
xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx (cannot be all zeroes)
mrpdu
Syntax 
[no] mrpdu
Context 
debug>service>id>mrp
Description 
This command enables debugging of the MRP PDUs that are received or transmitted.
The no form of the command disables debugging of MRP PDUs.
periodic-sm
Syntax 
[no] periodic-sm
Context 
debug>service>id>mrp
Description 
This command enables debugging of the periodic state machine.
The no form of the command disables debugging of the periodic state machine.
registrant-sm
Syntax 
[no] registrant-sm
Context 
debug>service>id>mrp
Description 
This command enables debugging of the registrant state machine.
The no form of the command disables debugging of the registrant state machine.
sap
Syntax 
[no] sap sap-id
Context 
debug>service>id>mrp
Description 
This command filters debug events and only shows events for the particular SAP.
The no form of the command removes the debug filter.
Parameters 
sap-id
See Common CLI Command Descriptions on page 1469 for command syntax.
 
sdp
Syntax 
[no] sdp sdp-id:vc-id
Context 
debug>service>id>mrp
Description 
This command filters debug events and only shows events for the particular SDP.
The no form of the command removes the debug filter.
Parameters 
sdp-id
Specifies the SDP ID for which to display information.
Default
All SDPs.
Values
1 — 17407
vc-id
Displays information about the virtual circuit identifier.
Values
1 — 4294967295