IES Show Commands

For feedback, use the following:

IES Show Commands

IES

customer

Syntax

customer [customer-id] [site customer-site-name]

Context

show>service

Description

This command displays service customer information.

Parameters

customer-id

Displays only information for the specified customer ID.

Default

All customer IDs display

Values

1 — 2147483647

site customer-site-name

Specifies the customer site which is an anchor point for an ingress and egress virtual scheduler hierarchy.

Output

Show Customer Command Output

The following table describes show customer command output fields:

Label

Description

Customer-ID

The ID that uniquely identifies a customer.

Contact

The name of the primary contact person.

Description

Generic information about the customer.

Phone

The phone/pager number to reach the primary contact person.

Total Customers

The total number of customers configured.

Multi-service site

Site

Multi-service site name. A multi-service customer site is a group of SAPs with common origination and termination points.

Description

Information about a specific customer's multi-service site.

Assignment

The port ID, MDA, or card number, where the SAP's that are members of this multi- service site are defined.

I. Sched Pol

The ingress QoS scheduler policy assigned to this multi-service site.

E. Sched Pol

The egress QoS scheduler policy assigned to this multi-service site.

Service Association

Service-ID

The ID that uniquely identifies a service.

SAP

Specifies the SAP assigned to the service.

Sample Output
*A:ALA-12# show service customer
==========================================================
Customers
==========================================================
Customer-ID : 1
Contact     : Manager
Description : Default customer
Phone       : (123) 555-1212
 
Customer-ID : 2
Contact     : Tech Support
Description : TiMetra Networks
Phone       : (234) 555-1212
 
Customer-ID : 3
Contact     : Fred
Description : TiMetra Networks
Phone       : (345) 555-1212
 
Customer-ID : 6
Contact     : Ethel
Description : Epipe Customer
Phone       : (456) 555-1212
 
Customer-ID : 7
Contact     : Lucy
Description : ABC Customer
Phone       : (567) 555-1212
 
Customer-ID : 8
Contact     : Customer Service
Description : IES Customer
Phone       : (678) 555-1212
 
Customer-ID : 274
Contact     : Mssrs. Beaucoup
Description : ABC Company
Phone       : 650 123-4567
 
Customer-ID : 94043
Contact     : Test Engineer on Duty
Description : TEST Customer
Phone       : (789) 555-1212
 
------------------------------------------------------
Total Customers : 8
-----------------------------------------------------------
*A:ALA-12#
 
 
*A:ALA-12# show service customer 274
==============================================================================
Customer  274
==============================================================================
Customer-ID : 274
Contact     : Mssrs. Beaucoup
Description : ABC Company
Phone       : 650 123-4567
------------------------------------------------------------------------------
Multi Service Site
------------------------------------------------------------------------------
Site        : west
Description : (Not Specified)
==============================================================================
*A:ALA-12#
 
 
*A:ALA-12# show service customer 274 site west
==============================================================================
Customer  274
==============================================================================
Customer-ID : 274
Contact     : Mssrs. Beaucoup
Description : ABC Company
Phone       : 650 123-4567
------------------------------------------------------------------------------
Multi Service Site
------------------------------------------------------------------------------
Site        : west
Description : (Not Specified)
Assignment  : Card 5
I. Sched Pol: SLA1
E. Sched Pol: (Not Specified)
------------------------------------------------------------------------------
Service Association
------------------------------------------------------------------------------
No Service Association Found.
==============================================================================
*A:ALA-12#
egress-label

Syntax

egress-label egress-label1 [egress-label2]

Context

show>service

Description

Display services using the range of egress labels.

If only the mandatory egress-label1 parameter is specified, only services using the specified label are displayed.

If both egress-label1 and egress-label2 parameters are specified, the services using the range of labels X where egress-label1 <= X <= egress-label2 are displayed.

Use the show router ldp bindings command to display dynamic labels.

Parameters

egress-label1

The starting egress label value for which to display services using the label range. If only egress-label1 is specified, services only using egress-label1 are displayed.

Values

0, 2049 — 131071

egress-label2

The ending egress label value for which to display services using the label range.

Default

The egress-label1 value.

Values

2049 — 131071

Output

Show Service Egress Command Output

The following table describes show service egress label output fields.

Label

Description

Svc Id

The value that identifies a service.

Sdp Id

The value that identifies a SDP.

Type

Indicates whether the SDP binding is a spoke or a mesh.

I. Lbl

The VC label used by the far-end device to send packets to this device in this service by the SDP.

E. Lbl

The VC label used by this device to send packets to the far-end device in this service by the SDP.

Number of bindings found

The total number of SDP bindings that exist within the specified egress label range.

Sample Output
*A:ALA-12# show service egress-label 0 10000
==============================================================================
Martini Service Labels                                                         
==============================================================================
Svc Id     Sdp Id             Type I.Lbl        E.Lbl                          
------------------------------------------------------------------------------
1          10:1               Mesh 0            0                              
1          20:1               Mesh 0            0                              
1          30:1               Mesh 0            0                              
1          100:1              Mesh 0            0                              
...
1          107:1              Mesh 0            0                              
1          108:1              Mesh 0            0                              
1          300:1              Mesh 0            0                              
1          301:1              Mesh 0            0                              
1          302:1              Mesh 0            0                              
1          400:1              Mesh 0            0                              
100        300:100            Spok 0            0                              
200        301:200            Spok 0            0                              
300        302:300            Spok 0            0                              
400        400:400            Spok 0            0                              
------------------------------------------------------------------------------
Number of Bindings Found : 21
==============================================================================
*A:ALA-12#
ingress-label

Syntax

ingress-label start-label [end-label]

Context

show>service

Description

This command displays services using the range of ingress labels. If only the mandatory start-label parameter is specified, only services using the specified label are displayed.

If both start-label and end-label parameters are specified, the services using the range of labels X where start-label <= X <= end-label are displayed.

Use the show router vprn-service-id ldp bindings command to display dynamic labels.

Parameters

start-label

The starting ingress label value for which to display services using the label range. If only start-label is specified, services only using start-label are displayed.

Values

0, 2048 — 131071

end-label

The ending ingress label value for which to display services using the label range.

Default

The start-label value.

Values

2049 — 131071

Output

Show Service Ingress-Label

The following table describes show service ingress-label output fields:

Label

Description

Svc ID

The service identifier.

SDP Id

The SDP identifier.

Type

Indicates whether the SDP is spoke or mesh.

I.Lbl

The ingress label used by the far-end device to send packets to this device in this service by the SDP.

E.Lbl

The egress label used by this device to send packets to the far-end device in this service by the SDP.

Number of Bindings Found

The number of SDP bindings within the label range specified.

Sample Output
*A:ALA-12# show service ingress-label 0
==============================================================================
Martini Service Labels                                                         
==============================================================================
Svc Id     Sdp Id             Type I.Lbl        E.Lbl                          
------------------------------------------------------------------------------
1          10:1               Mesh 0            0                              
1          20:1               Mesh 0            0                              
1          30:1               Mesh 0            0                              
1          50:1               Mesh 0            0                              
1          100:1              Mesh 0            0                              
1          101:1              Mesh 0            0                              
1          102:1              Mesh 0            0                              
1          103:1              Mesh 0            0                              
1          104:1              Mesh 0            0                              
1          105:1              Mesh 0            0                              
1          106:1              Mesh 0            0                              
1          107:1              Mesh 0            0                              
1          108:1              Mesh 0            0                              
1          300:1              Mesh 0            0                              
1          301:1              Mesh 0            0                              
1          302:1              Mesh 0            0                              
1          400:1              Mesh 0            0                              
1          500:2              Spok 131070       2001                           
1          501:1              Mesh 131069       2000                           
100        300:100            Spok 0            0                              
200        301:200            Spok 0            0                              
300        302:300            Spok 0            0                              
400        400:400            Spok 0            0                              
------------------------------------------------------------------------------
Number of Bindings Found : 23                                                  
------------------------------------------------------------------------------
*A:ALA-12# 
sap-using

Syntax

sap-using [msap] [dyn-script] [description]

sap-using [sap sap-id] [vlan-translation | anti-spoof] [description]

sap-using [sap sap-id]

sap-using interface [ip-address | ip-int-name]

sap-using [ingress | egress] atm-td-profile td-profile-id

sap-using [ingress | egress] filter filter-id

sap-using [ingress | egress] qos-policy qos-policy-id

sap-using authentication-policy policy-name

Context

show>service

Description

Displays SAP information.

If no optional parameters are specified, the command displays a summary of all defined SAPs. The optional parameters restrict output to only SAPs matching the specified properties.

Parameters

sap sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI Command Descriptions for command syntax.

ingress

Specifies matching an ingress policy.

egress

Specifies matching an egress policy.

qos-policy qos-policy-id

The ingress or egress QoS Policy ID for which to display matching SAPs.

Values

1 — 65535

atm-td-profile td-profile-id

Displays SAPs using this traffic description.

filter filter-id

The ingress or egress filter policy ID for which to display matching SAPs.

Values

1 — 65535

dyn-script

Displays dynamic service SAPs information.

authentication policy-name

The session authentication policy for which to display matching SAPs.

interface

Specifies matching SAPs with the specified IP interface.

ip-addr

The IP address of the interface for which to display matching SAPs.

Values

1.0.0.0 — 223.255.255.255

ip-int-name

The IP interface name for which to display matching SAPs.

Output

Show Service SAP

The following table describes show service SAP output fields:

Label

Description

Port ID

The ID of the access port where the SAP is defined.

Svc ID

The value that identifies the service.

SapMTU

The SAP MTU value.

Igr.QoS

The SAP ingress QoS policy number specified on the ingress SAP.

Ing.Fltr

The MAC or IP filter policy ID applied to the ingress SAP.

E.QoS

The SAP egress QoS policy number specified on the egress SAP.

Egr.Fltr

The MAC or IP filter policy ID applied to the egress SAP.

A.Pol

The accounting policy ID assigned to the SAP.

Adm

The administrative state of the SAP.

Opr

The actual state of the SAP.

Sample Output
*A:ALA-48# show service sap-using sap 2/1/10:0
===============================================================================
Service Access Points Using Port 2/1/10:0
===============================================================================
PortId                          SvcId      Ing.  Ing.    Egr.  Egr.   Adm  Opr
                                           QoS   Fltr    QoS   Fltr
-------------------------------------------------------------------------------
2/1/10:0                        13         1     none    1     none   Up   Down
-------------------------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------------------------
===============================================================================
*A:ALA-48#
*A:ALA-12#  show service sap-using egress atm-td-profile 2 
=============================================================================== 
Service Access Point Using ATM Traffic Profile 2 
=============================================================================== 
PortId 	SvcId 	I.QoS 	I.Fltr 	E.QoS E.Fltr A.Pol Adm Opr 
------------------------------------------------------------------------------- 
5/1/1:0/11 511111 2 none 2 none none Up Up

5/1/1:0/12 511112 2 none 2 none none Up Up

5/1/1:0/13 511113 2 none 2 none none Up Up

5/1/1:0/14 511114 2 none 2 none none Up Up

5/1/1:0/15 511115 2 none 2 none none Up Up

5/1/1:0/16 511116 2 none 2 none none Up Up

5/1/1:0/17 511117 2 none 2 none none Up Up

5/1/1:0/18 511118 2 none 2 none none Up Up

5/1/1:0/19 511119 2 none 2 none none Up Up

5/1/1:0/20 511120 2 none 2 none none Up Up

5/1/1:0/21 511121 2 none 2 none none Up Up

5/1/1:0/22 511122 2 none 2 none none Up Up

5/1/1:0/23 511123 2 none 2 none none Up Up

5/1/1:0/24 511124 2 none 2 none none Up Up

5/1/1:0/25 511125 2 none 2 none none Up Up
...
=============================================================================== 
*A:ALA-12# 
sdp

Syntax

sdp [sdp-id | far-end ip-address] [detail | keep-alive-history]

Context

show>service

Description

This command displays SDP information. If no optional parameters are specified, a summary SDP output for all SDPs is displayed.

Parameters

sdp-id

Specifies the SDP ID for which to display information.

Default

All SDPs.

Values

1 — 17407

far-end ip-address

Displays only SDPs matching with the specified far-end IP address.

Default

SDPs with any far-end IP address.

detail

Displays detailed SDP information.

Default

SDP summary output.

keep-alive-history

Displays the last fifty SDP keepalive events for the SDP.

Default

SDP summary output.

Output

Show Service SDP

The following table describes show service SDP output fields:

Label

Description

SDP Id

The SDP identifier.

Adm MTU

Specifies the desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Opr MTU

Specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

IP address

Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP.

Adm

Admin State

Specifies the administrative state of the SDP.

Opr

Oper State

Specifies the operational state of the SDP.

Deliver

Specifies the type of delivery used by the SDP: GRE or MPLS.

Flags

Specifies the conditions that affect the operating status of this SDP.

Signal

Signaling

Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP.

Last Status Change

Specifies the time of the most recent operating status change to this

SDP.

Sample Output
*A:ALA-12# show service sdp
==============================================================================
Services: Service Destination Points                                           
==============================================================================
SdpId    Adm MTU   Opr MTU   IP address       Adm  Opr         Deliver Signal  
------------------------------------------------------------------------------
10       4462      4462      10.20.1.3        Up   Dn NotReady MPLS    TLDP    
40       4462      1534      10.20.1.20       Up   Up          MPLS    TLDP    
60       4462      1514      10.20.1.21       Up   Up          GRE     TLDP    
100      4462      4462      180.0.0.2        Down Down        GRE     TLDP    
500      4462      4462      10.20.1.50       Up   Dn NotReady GRE     TLDP    
------------------------------------------------------------------------------
Number of SDPs : 5                                                            
------------------------------------------------------------------------------
*A:ALA-12# 
 
 
*A:ALA-12# show service sdp 2 detail
===============================================================================
Service Destination Point (Sdp Id : 2) Details
-------------------------------------------------------------------------------
 Sdp Id 2  -(10.10.10.104)
-------------------------------------------------------------------------------
Description           : GRE-10.10.10.104
SDP Id               : 2
Admin Path MTU       : 0                     Oper Path MTU      : 0
Far End              : 10.10.10.104          Delivery           : GRE
Admin State          : Up                    Oper State         : Down
Flags                : SignalingSessDown TransportTunnDown
Signaling            : TLDP                  VLAN VC Etype      : 0x8100
Last Status Change   : 02/01/2007 09:11:39   Adv. MTU Over.     : No
Last Mgmt Change     : 02/01/2007 09:11:46
 
KeepAlive Information :
Admin State          : Disabled              Oper State         : Disabled
Hello Time           : 10                    Hello Msg Len      : 0
Hello Timeout        : 5                     Unmatched Replies  : 0
Max Drop Count       : 3                     Hold Down Time     : 10
Tx Hello Msgs        : 0                     Rx Hello Msgs      : 0
 
Associated LSP LIST :
SDP Delivery Mechanism is not MPLS
===============================================================================
*A:ALA-12# 
 
 
*A:ALA-12# show service sdp 8
==============================================================================
Service Destination Point (Sdp Id : 8)
==============================================================================
SdpId    Adm MTU   Opr MTU   IP address       Adm  Opr         Deliver Signal
------------------------------------------------------------------------------
8        4462      4462      10.10.10.104     Up   Dn NotReady MPLS    TLDP
==============================================================================
*A:ALA-12# 
===============================================================================
Service Destination Point (Sdp Id : 8) Details
===============================================================================
Sdp Id 8  -(10.10.10.104)
-------------------------------------------------------------------------------
Description           : MPLS-10.10.10.104
SDP Id               : 8
Admin Path MTU       : 0                     Oper Path MTU      : 0
Far End              : 10.10.10.104          Delivery           : MPLS
Admin State          : Up                    Oper State         : Down
Flags                : SignalingSessDown TransportTunnDown
Signaling            : TLDP                  VLAN VC Etype      : 0x8100
Last Status Change   : 02/01/2007 09:11:39   Adv. MTU Over.     : No
Last Mgmt Change     : 02/01/2007 09:11:46
KeepAlive Information :
Admin State          : Disabled              Oper State         : Disabled
Hello Time           : 10                    Hello Msg Len      : 0
Hello Timeout        : 5                     Unmatched Replies  : 0
Max Drop Count       : 3                     Hold Down Time     : 10
Tx Hello Msgs        : 0                     Rx Hello Msgs      : 0
 
Associated LSP LIST :
Lsp Name             : to-104
Admin State          : Up                    Oper State         : Down
Time Since Last Tran*: 01d07h36m
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALA-12#
 
When network domains are configured, the SDP egress interface state can be verified by using the following command:
*A:Dut-T# show service sdp egressifs 
===============================================================================
SDP Egress Ifs State Table
===============================================================================
SDP Id              Network Domain                   State                     
-------------------------------------------------------------------------------
100                 net1                             consistent                
-------------------------------------------------------------------------------
SDPs : 1
===============================================================================
*A:Dut-Tr# 
sdp-using

Syntax

sdp-using [sdp-id[:vc-id] | far-end ip-address]

Context

show>service

Description

This command displays services using SDP or far-end address options.

Parameters

sdp-id

Displays only services bound to the specified SDP ID.

Values

1 — 17407

vc-id

Displays information about the virtual circuit identifier.

Values

1 — 4294967295

far-end ip-address

Displays only services matching with the specified far-end IP address.

Default

Services with any far-end IP address.

Output

Show Service SDP Using X

The following table describes show service sdp-using output fields.

Label

Description

Svc ID

The service identifier.

Sdp ID

The SDP identifier.

Type

Type of SDP: spoke or mesh.

Far End

The far-end address of the SDP.

Oper State

The operational state of the service.

I.Label

The label used by the far-end device to send packets to this device in this service by this SDP.

E.Label

The label used by this device to send packets to the far-end device in this service by this SDP.

Sample Output
*A:ALA-1# show service sdp-using 300
===============================================================================
Service Destination Point (Sdp Id : 300)
===============================================================================
SvcId       SdpId               Type Far End        Opr State I.Label  E.Label
-------------------------------------------------------------------------------
1           300:1               Mesh 10.0.0.13      Up        131071   131071
2           300:2               Spok 10.0.0.13      Up        131070   131070
100         300:100             Mesh 10.0.0.13      Up        131069   131069
101         300:101             Mesh 10.0.0.13      Up        131068   131068
102         300:102             Mesh 10.0.0.13      Up        131067   131067
-------------------------------------------------------------------------------
Number of SDPs : 5
===============================================================================
*A:ALA-1#
service-using

Syntax

service-using [ies] [customer customer-id]

Context

show>service

Description

This command displays the services matching certain usage properties. If no optional parameters are specified, all services defined on the system are displayed.

Parameters

ies

Displays matching IES services.

sdp sdp-id

Displays only services bound to the specified SDP ID.

Default

Services bound to any SDP ID.

Values

1 — 17407

customer customer-id

Displays services only associated with the specified customer ID.

Default

Services associated with an customer.

Values

1 — 2147483647

Output

Show Service Service-Using

The following table describes show service service-using output fields:

Label

Description

Service Id

The value that identifies the service.

Type

Specifies the service type configured for the service ID.

Adm

The administrative state of the service.

Opr

The operating state of the service.

CustomerID

The ID of the customer who owns this service.

Last Mgmt Change

The date and time of the most recent management-initiated change to this service.

Sample Output
A:ALA-48# show service service-using ies
===============================================================================
Services [ies]
===============================================================================
ServiceId    Type      Adm    Opr        CustomerId        Last Mgmt Change
-------------------------------------------------------------------------------
88           IES       Up     Down       8                 07/25/2006 15:46:28
89           IES       Up     Down       8                 07/25/2006 15:46:28
104          IES       Up     Down       1                 07/25/2006 15:46:28
200          IES       Up     Down       1                 07/25/2006 15:46:28
214          IES       Up     Down       1                 07/25/2006 15:46:28
321          IES       Up     Down       1                 07/25/2006 15:46:28
322          IES       Down   Down       1                 07/25/2006 15:46:28
1001         IES       Up     Down       1730              07/25/2006 15:46:28
-------------------------------------------------------------------------------
Matching Services : 8
-------------------------------------------------------------------------------
A:ALA-48#
subscriber-using

Syntax

subscriber-using [service-id service-id] [sap-id sap-id] [interface ip-int-name] [ip ip-address[/mask]] [mac ieee-address] [sub-profile sub-profile-name] [sla-profile sla-profile-name]

Context

show>service>subscriber-using

Description

This command displays subscribers using certain options.

Parameters

service-id service-id

Display subscriber information about the specified service ID.

Values

1 — 2147483648

sap-id sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI Command Descriptions for command syntax.

interface ip-int-name

Display subscriber information about the specified interface.

ip ip-address[/mask

Display subscriber information about the specified IP address.

mac ieee-address

Display subscriber information about the specified MAC address.

sub-profile sub-profile-name

Display subscriber information about the specified subscriber profile name.

sla-profile sla-profile-name

Display subscriber information about the specified SLA profile name.

id

Syntax

id service-id {all | arp | base | sap | sdp}

Context

show>service

Description

This command displays information for a particular service-id.

Parameters

service-id

The unique service identification number to identify the service in the service domain.

all

Display detailed information about the service.

arp

Display ARP entries for the service.

arp-host

Displays ARP host related information.

base

Display basic service information.

interface

Display service interfaces.

sap

Display SAPs associated to the service.

sdp

Display SDPs associated with the service.

all

Syntax

all

Context

show>service>id

Description

This command displays detailed information for all aspects of the service.

Output

Show All Service-ID Output

The following table describes the show all service-id command output fields:

Label

Description

Service Detailed Information

Service Id

The service identifier.

VPN Id

The number which identifies the VPN.

Service Type

Specifies the type of service.

SDP Id

The SDP identifier.

Description

Generic information about the service.

Customer Id

The customer identifier.

Last Mgmt Change

The date and time of the most recent management-initiated change to this customer.

SAP Count

The number of SAPs specified for this service.

SDP Bind Count

The number of SDPs bound to this service.

Service Destination Points (SDPs)

SDP Id

The SDP identifier.

Type

Indicates whether this Service SDP binding is a spoke or a mesh.

Admin Path MTU

The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Oper Path MTU

The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Delivery

Specifies the type of delivery used by the SDP: GRE or MPLS.

Admin State

The administrative state of this SDP.

Oper State

The operational state of this SDP.

Ingress Label

The label used by the far-end device to send packets to this device in this service by this SDP.

Egress Label

The label used by this device to send packets to the far-end device in this service by this SDP.

Ingress Filter

The ID of the ingress filter policy.

Egress Filter

The ID of the egress filter policy.

Far End

Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP.

Last Changed

The date and time of the most recent change to this customer.

Signaling

Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP.

Admin State

Specifies the operating status of the service.

Oper State

The current status of the service.

Hello Time

Specifies how often the SDP echo request messages are transmitted on this SDP.

Hello Msg Len

Specifies the length of the SDP echo request messages transmitted on this SDP.

Max Drop Count

Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault.

Hold Down Time

Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state.

SDP Delivery Mechanism

When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far-end field.

If the SDP type is GRE, then the following message displays:

“SDP Delivery Mechanism is not MPLS”

Number of SDPs

The total number SDPs applied to this service ID.

Service Access Points

Service Id

The service identifier.

Port Id

The ID of the access port where this SAP is defined.

Description

Generic information about the SAP.

Encap

The value of the label used to identify this SAP on the access port.

Admin State

The desired state of the SAP.

Oper State

The operating state of the SAP.

Last Changed

The date and time of the last change.

Admin MTU

The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Oper MTU

The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Ingress qos-policy

The SAP ingress QoS policy ID.

Egress qos-policy

The SAP egress QoS policy ID.

Ingress Filter-Id

The SAP ingress filter policy ID.

Egress Filter-Id

The SAP egress filter policy ID.

Multi Svc Site

Indicates the multi-service site that the SAP is a member.

Ingress sched-policy

Indicates the ingress QoS scheduler for the SAP.

Egress sched-policy

Indicates the egress QoS scheduler for the SAP.

Acct. Pol

Indicates the accounting policy applied to the SAP.

Collect Stats

Specifies whether accounting statistics are collected on the SAP.

SAP Statistics

Dropped

The number of packets or octets dropped.

Offered Hi Priority

The number of high priority packets, as determined by the SAP ingress QoS policy.

Offered Low Priority

The number of low priority packets, as determined by the SAP ingress QoS policy.

Forwarded In Profile

The number of in-profile packets or octets (rate below CIR) forwarded.

Forwarded Out Profile

The number of out-of-profile packets or octets (rate above CIR) forwarded.

Queueing Stats

Dropped In Profile

The number of in-profile packets or octets discarded.

Dropped Out Profile

The number of out-of-profile packets or octets discarded.

Forwarded In Profile

The number of in-profile packets or octets (rate below CIR) forwarded.

Forwarded Out Profile

The number of out-of-profile packets or octets (rate above CIR) forwarded.

SAP per Queue stats

Ingress Queue 1

The index of the ingress QoS queue of this SAP.

High priority offered

The packets or octets count of the high priority traffic for the SAP.

High priority dropped

The number of high priority traffic packets/octets dropped.

Low priority offered

The packets or octets count of the low priority traffic.

Low priority dropped

The number of low priority traffic packets/octets dropped.

In profile forwarded

The number of in-profile packets or octets (rate below CIR) forwarded.

Out profile forwarded

The number of out-of-profile octets (rate above CIR) forwarded.

Egress Queue 1

The index of the egress QoS queue of the SAP.

In profile forwarded

The number of in-profile packets or octets (rate below CIR) forwarded.

IPCP Address Extension Details

In profile dropped

The number of in-profile packets or octets dropped for the SAP.

Peer IP Addr

Specifies the remote IP address to be assigned to the far-end of the associated PPP/MLPPP link via IPCP extensions.

Peer Pri DNS Addr

Specifies a unicast IPv4 address for the primary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions.

Peer Sec DNS Addr

Specifies a unicast IPv4 address for the secondary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions. (optional)
 
arp

Syntax

arp [ip-address] | [mac ieee-address] | [sap sap-id] | [interface ip-int-name] [sdp sdp-id:vc-id]

Context

show>service>id

Description

Displays the ARP table for the IES instance. The ARP entries are displayed uniquely. Each MAC associated with the child group-interfaces are displayed with each ARP entry. They do not reflect actual ARP entries but are displayed along the interfaces ARP entry for easy lookup.

Parameters

ip-address

Displays only ARP entries in the ARP table with the specified IP address.

Default

All IP addresses.

mac ieee-address

Displays only ARP entries in the ARP table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.

Default

All MAC addresses.

sap sap-id

Displays SAP information for the specified SAP ID. See Common CLI Command Descriptions for command syntax.

port-id

interface

Specifies matching service ARP entries associated with the IP interface.

ip-address

The IP address of the interface for which to display matching ARP entries.

Values

1.0.0.0 — 223.255.255.255

ip-int-name

The IP interface name for which to display matching ARPs.

sdp-id

The SDP identifier.

vc-id

The virtual circuit identifier.

Values

1 — 4294967295

Output

Show Service-ID ARP

The following table describes show service-id ARP output fields.

Label

Description

IP Address

The IP address.

MAC Address

The specified MAC address.

Type

Static

FDB entries created by management.

Learned

Dynamic entries created by the learning process.

OAM

Entries created by the OAM process.

Other — Local entries for the IP interfaces created.

Expiry

The age of the ARP entry.

Interface

The interface applied to the service.

SAP

The SAP ID.

Sample Output
A:ALA-49# show service id 88 arp
====================================================================================
ARP Table
====================================================================================
IP Address   MAC Address        Type    Expiry       Interface   SAP
------------------------------------------------------------------------------------
11.30.1.1    76:1e:ff:00:01:41  Other   00h00m00s    ies30       lag-1:30
11.31.1.1    76:1e:ff:00:01:41  Other   00h00m00s    ies30       lag-1:30
11.37.1.1    00:00:00:00:00:00  Other   00h00m00s    foo2        n/a
11.20.1.1    76:1e:ff:00:00:00  Other   00h00m00s    s2          subscrib*
             76:1e:ff:00:01:41                       g3          lag-1
11.20.1.10   00:00:aa:aa:aa:dd  Managed 00h00m00s    g3          lag-1:11
11.20.1.11   00:00:aa:aa:aa:dd  Managed 00h00m00s    g3          lag-1:11
11.20.1.12   00:00:aa:aa:aa:dd  Managed 00h00m00s    g3          lag-1:11
11.38.1.1    76:1e:ff:00:00:00  Other   00h00m00s    s3          subscrib*
             76:21:04:01:00:01                       g5          4/1/1
             76:21:04:01:00:01                       g7          4/1/1
11.39.1.1    76:1e:ff:00:00:00  Other   00h00m00s    s3          subscrib*
             76:21:04:01:00:01                       g5          41/1/1
             76:21:04:01:00:01                       g7          4/1/1
11.38.1.2    76:22:07:01:00:01  Managed 00h00m00s    g7          4/1/1:25*
11.38.10.1   76:22:07:01:00:01  Managed 00h00m00s    g7          4/1/1:25*
11.38.99.1   76:22:07:01:00:01  Managed 00h00m00s    g7          4/1/1:25*
====================================================================================
* indicats that the corresponding row element may have been truncated.
A:ALA-49#
arp-host

Syntax

arp-host [wholesaler service-id] [sap sap-id | interface interface-name | ip-address ip-address[/mask] | mac ieee-address | {[port port-id] [no-inter-dest-id | inter-dest-id inter-dest-id]}] [detail]

arp-host statistics [sap sap-id | interface interface-name]

arp-host summary [interface interface-name]

Context

show>service>id

Description

This command displays ARP host related information.

Sample Output
*A:Dut-C# show service id 2 arp-host 
===============================================================================
ARP host table, service 2
===============================================================================
IP Address      Mac Address       Sap Id              Remaining           MC   
                                                      Time                Stdby
-------------------------------------------------------------------------------
128.128.1.2     00:80:00:00:00:01 2/1/5:2             00h04m41s                
128.128.1.3     00:80:00:00:00:02 2/1/5:2             00h04m42s                
128.128.1.4     00:80:00:00:00:03 2/1/5:2             00h04m43s                
128.128.1.5     00:80:00:00:00:04 2/1/5:2             00h04m44s                
128.128.1.6     00:80:00:00:00:05 2/1/5:2             00h04m45s                
128.128.1.7     00:80:00:00:00:06 2/1/5:2             00h04m46s                
128.128.1.8     00:80:00:00:00:07 2/1/5:2             00h04m47s                
128.128.1.9     00:80:00:00:00:08 2/1/5:2             00h04m48s                
128.128.1.10    00:80:00:00:00:09 2/1/5:2             00h04m49s                
128.128.1.11    00:80:00:00:00:0a 2/1/5:2             00h04m50s                
-------------------------------------------------------------------------------
Number of ARP hosts : 10
===============================================================================
*A:Dut-C#
 
 
*A:Dut-C# show service id 2 arp-host ip-address 128.128.1.2 detail 
===============================================================================
ARP hosts for service 2
===============================================================================
Service ID           : 2                                                       
IP Address           : 128.128.1.2
MAC Address          : 00:80:00:00:00:01                                       
SAP                  : 2/1/5:2                                                 
Remaining Time       : 00h04m58s                                               
 
Sub-Ident            : "alu_1_2"                                               
Sub-Profile-String   : ""                                                      
SLA-Profile-String   : ""                                                      
App-Profile-String   : ""                                                      
ARP host ANCP-String : ""
ARP host Int Dest Id : ""
RADIUS-User-Name     : "128.128.1.2"
 
Session Timeout (s)  : 301                                                     
Start Time           : 02/09/2009 16:35:07                                     
Last Auth            : 02/09/2009 16:36:34                                     
Last Refresh         : 02/09/2009 16:36:38                                     
Persistence Key      : N/A                                                     
-------------------------------------------------------------------------------
Number of ARP hosts : 1
===============================================================================
*A:Dut-C#
 
 
*A:Dut-C# show service id 2 arp-host statistics                    
==============================================================================
ARP host statistics
==============================================================================
Num Active Hosts             : 20                                             
Received Triggers            : 70                                             
Ignored Triggers             : 10                                             
Ignored Triggers (overload)  : 0                                              
SHCV Checks Forced           : 0                                              
Hosts Created                : 20                                             
Hosts Updated                : 40                                             
Hosts Deleted                : 0                                              
Authentication Requests Sent : 40                                             
==============================================================================
*A:Dut-C#
 
 
*A:Dut-C# show service id 2 arp-host summary    
=============================================================
ARP host Summary, service 2
=============================================================
Sap                    Used        Provided    Admin State                     
-------------------------------------------------------------
sap:2/1/5:2            20          8000        inService     
-------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------
=============================================================
*A:Dut-C#
statistics

Syntax

statistics [policy name] [sap sap-id]

Context

show>service>id>authentication

Description

Displays session authentication statistics for this service.

Parameters

policy name

Specifies the subscriber authentication policy statistics to display.

sap sap-id

Specifies the SAP ID statistics to display. See Common CLI Command Descriptions for command syntax.

See Common CLI Command Descriptions for command syntax.

Sample Output
*A:ALA-1# show service id 11 authentication statistics
---------------------------------------------------------------
Authentication statistics
---------------------------------------------------------------
Interface / SAP                 Authentication  Authentication
                                Successful      Failed
---------------------------------------------------------------
abc-11-90.1.0.254               1582            3
---------------------------------------------------------------
Number of entries: 1
===============================================================
*A:ALA-1#
authentication

Syntax

authentication

Context

show>service>id

Description

This command enables the context to display subscriber authentication information.

base

Syntax

base

Context

show>service>id

Description

This command displays basic information about this IES service.

Sample Output
*A:ALA-A# show service id 100 base
---------------------------------------------------------------
Service Basic Information
---------------------------------------------------------------
Service Id        : 100                 Vpn Id            : 100
Service Type      : IES
Description       : Default Ies description for service id 100
Customer Id       : 1
Last Status Change: 08/29/2006 17:44:28
Last Mgmt Change  : 08/29/2006 17:44:28
Admin State       : Up                  Oper State        : Up
SAP Count         : 2
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier                       Type         AdmMTU  OprMTU  Adm     Opr
-------------------------------------------------------------------------------
sap:1/1/3                        null         1514    1514    Up      Up
sap:1/1/4                        null         1514    1514    Up      Up
===============================================================================
*A:ALA-A#
dhcp

Syntax

dhcp

Context

show>service>id

Description

This command enables the context to display DHCP information for the specified service.

lease-state

Syntax

lease-state [[sap sap-id] | [sdp sdp-id:vc-id] | [interface interface-name] | [ip-address ip-address]] [detail]

Context

show>service>id>dhcp

Description

This command displays DHCP lease state related information.

Parameters

sap sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI Command Descriptions for command syntax.

sdp-id

The SDP identifier.

Values

1 — 17407

vc-id

The virtual circuit ID on the SDP ID for which to display information.

Values

1 — 4294967295

interface interface-name

Displays information for the specified IP interface.

ip-address ip-address

Displays information associated with the specified IP address.

detail

Displays detailed information.

Sample Output
A:ALA-_Dut-A# show service id 13 dhcp lease-state 
===============================================================================
DHCP lease state table, service 13
===============================================================================
IP Address      Mac Address       Sap/Sdp Id          Remaining  Lease    MC   
                                                      LifeTime   Origin   Stdby
-------------------------------------------------------------------------------
13.13.40.1      00:00:00:00:00:13 1/1/1:13            00h00m58s  Radius        
-------------------------------------------------------------------------------
Number of lease states : 1
===============================================================================
A:ALA-_Dut-A# 
 
 
A:ALA-_Dut-A# show service id 13 dhcp lease-state detail 
===============================================================================
DHCP lease states for service 13
===============================================================================
Service ID           : 13                                                      
IP Address           : 13.13.40.1
Mac Address          : 00:00:00:00:00:13                                       
Interface            : ies-13-13.13.1.1                                        
SAP                  : 1/1/1:13                                                
Remaining Lifetime   : 00h00m58s                                               
Persistence Key      : N/A                                                     
 
Sub-Ident            : "TEST"                                              
Sub-Profile-String   : "ADSL GO"                                               
SLA-Profile-String   : "BE-Video"                                              
Lease ANCP-String    : ""
 
Sub-Ident origin     : Radius                                                  
Strings origin       : Radius                                                  
Lease Info origin    : Radius                                                  
 
Ip-Netmask           : 255.255.0.0                                             
Broadcast-Ip-Addr    : 13.13.255.255                                           
Default-Router       : N/A                                                     
Primary-Dns          : 13.13.254.254                                           
Secondary-Dns        : 13.13.254.253                                           
 
ServerLeaseStart     : 12/24/2006 23:44:07                                     
ServerLastRenew      : 12/24/2006 23:44:07                                     
ServerLeaseEnd       : 12/24/2006 23:45:07                                     
Session-Timeout      : 0d 00:01:00                                             
DHCP Server Addr     : N/A                                                     
 
Persistent Relay Agent Information
  Circuit Id         : ancstb6_Dut-A|13|ies-13-13.13.1.1|0|13
  Remote Id          : stringtest
-------------------------------------------------------------------------------
Number of lease states : 1
===============================================================================
A:ALA-_Dut-A# 
Routed CO Output Example
A:ALA-_Dut-A# show service id 13 dhcp lease-state 
===============================================================================
DHCP lease state table, service 13
===============================================================================
IP Address      Mac Address       Sap/Sdp Id          Remaining  Lease    MC   
                                                      LifeTime   Origin   Stdby
-------------------------------------------------------------------------------
13.13.40.1      00:00:00:00:00:13 1/1/1:13            00h00m58s  Radius        
-------------------------------------------------------------------------------
Number of lease states : 1
===============================================================================
A:ALA-_Dut-A# 
 
 
A:ALA-_Dut-A# show service id 13 dhcp lease-state detail 
===============================================================================
DHCP lease states for service 13
===============================================================================
Service ID           : 13                                                      
IP Address           : 13.13.40.1
Mac Address          : 00:00:00:00:00:13                                       
Subscriber-interface : ies-13-13.13.1.1                                        
Group-interface      : intf-13                                                 
SAP                  : 1/1/1:13                                                
Remaining Lifetime   : 00h00m58s                                               
Persistence Key      : N/A                                                     
 
Sub-Ident            : "TEST"                                              
Sub-Profile-String   : "ADSL GO"                                               
SLA-Profile-String   : "BE-Video"                                              
Lease ANCP-String    : ""
 
Sub-Ident origin     : Radius                                                  
Strings origin       : Radius                                                  
Lease Info origin    : Radius                                                  
 
Ip-Netmask           : 255.255.0.0                                             
Broadcast-Ip-Addr    : 13.13.255.255                                           
Default-Router       : N/A                                                     
Primary-Dns          : 13.13.254.254                                           
Secondary-Dns        : 13.13.254.253                                           
 
ServerLeaseStart     : 12/24/2006 23:48:23                                     
ServerLastRenew      : 12/24/2006 23:48:23                                     
ServerLeaseEnd       : 12/24/2006 23:49:23                                     
Session-Timeout      : 0d 00:01:00                                             
DHCP Server Addr     : N/A                                                     
 
Persistent Relay Agent Information
  Circuit Id         : ancstb6_Dut-A|13|intf-13|0|13
  Remote Id          : stringtest
-------------------------------------------------------------------------------
Number of lease states : 1
===============================================================================
A:ALA-_Dut-A# 
 
 
Wholesaler/Retailer Output Example
A:ALA-_Dut-A# show service id 2000 dhcp lease-state detail 
===============================================================================
DHCP lease states for service 2000
-------------------------------------------------------------------------------
Wholesaler 1000 Leases
-------------------------------------------------------------------------------
Service ID           : 1000                                                    
IP Address           : 13.13.1.254
Mac Address          : 00:00:00:00:00:13                                       
Subscriber-interface : whole-sub                                               
Group-interface      : intf-13                                                 
Retailer             : 2000                                                    
Retailer If          : retail-sub                                              
SAP                  : 1/1/1:13                                                
Remaining Lifetime   : 00h09m59s                                               
Persistence Key      : N/A                                                     
 
Sub-Ident            : "TEST"                                              
Sub-Profile-String   : "ADSL GO"                                               
SLA-Profile-String   : "BE-Video"                                              
Lease ANCP-String    : ""
 
Sub-Ident origin     : Retail DHCP                                             
Strings origin       : Retail DHCP                                             
Lease Info origin    : Retail DHCP                                             
 
Ip-Netmask           : 255.255.0.0                                             
Broadcast-Ip-Addr    : 13.13.255.255                                           
Default-Router       : N/A                                                     
Primary-Dns          : N/A                                                     
Secondary-Dns        : N/A                                                     
 
ServerLeaseStart     : 12/25/2006 00:29:41                                     
ServerLastRenew      : 12/25/2006 00:29:41                                     
ServerLeaseEnd       : 12/25/2006 00:39:41                                     
Session-Timeout      : 0d 00:10:00                                             
DHCP Server Addr     : 10.232.237.2                                            
 
Persistent Relay Agent Information
  Circuit Id         : 1/1/1:13
  Remote Id          : stringtest
-------------------------------------------------------------------------------
Number of lease states : 1
===============================================================================
A:ALA-_Dut-A#
statistics

Syntax

statistics [sap sap-id

statistics [sdp sdp-id:vc-id]

statistics [interface interface-name]

Context

show>service>id>dhcp

Description

Displays DHCP statistics information.

Parameters

sap sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI Command Descriptions for command syntax.

sdp-id

The SDP identifier.

Values

1 — 17407

vc-id

The virtual circuit ID on the SDP ID for which to display information.

Values

1 — 4294967295

interface interface-name

Displays information for the specified IP interface.

summary

Syntax

summary

Context

show>service>id>dhcp

Description

Displays DHCP configuration summary information.

Output

Show DHCP Summary Output

The following table describes the output fields for DHCP summary.

Label

Description

Interface Name

Name of the router interface.

Arp Populate

Specifies whether or not ARP populate is enabled.

Used/Provided

Used

The number of lease-states that are currently in use on a specific interface, that is, the number of clients on that interface got an IP address by DHCP. This value is always less than or equal to the ‘Provided’ field.

Provided

The lease-populate value that is configured for a specific interface.

Info Option

Indicates whether Option 82 processing is enabled on the interface.

Admin State

Indicates the administrative state.

Sample Output
A:ALA-49# show service id 88 dhcp summary
===============================================================================
DHCP Summary, service 88
===============================================================================
Interface Name                   Arp      Used/                 Info    Admin
  SapId/Sdp                      Populate Provided              Option  State
-------------------------------------------------------------------------------
Sector A                         No       0/0                   Keep    Up
  sap:7/1/1.2.2                           0/0
grp-if                           No       0/1                   Keep    Down
  sap:2/2/2:0                             0/1
  sap:2/2/2:0                             0/1
test                             No       0/0                   Keep    Up
  sap:10/1/2:0                            0/0
-------------------------------------------------------------------------------
Interfaces: 3
===============================================================================
A:ALA-49#
gsmp

Syntax

gsmp

Context

show>service>id

Description

This command enables the context to display GSMP information.

neighbors

Syntax

neighbors group [name] [ip-address]

Context

show>service>id>gsmp

Description

This command displays GSMP neighbor information.

Parameters

group

A GSMP group defines a set of GSMP neighbors which have the same properties.

name

Specifies a GSMP group name is unique only within the scope of the service in which it is defined.

ip-address

Specifies the ip-address of the neighbor.

Sample Output

These commands show the configured neighbors per service, regardless of the fact there exists an open TCP connection with this neighbor. The admin state is shown because for a neighbor to be admin enabled, the service, gsmp node, group node and the neighbor node in this service must all be in 'no shutdown' state. Session gives the number of session (open TCP connections) for each configured neighbor.

A:active>show>service>id>gsmp# neighbors

============================================================================

GSMP neighbors

============================================================================

Group Neighbor AdminState Sessions

----------------------------------------------------------------------------

dslam1 192.168.1.2 Enabled 0

dslam1 192.168.1.3 Enabled 0

----------------------------------------------------------------------------

Number of neighbors shown: 2

============================================================================

A:active>show>service>id>gsmp#

A:active>show>service>id>gsmp# neighbors group dslam1

============================================================================

GSMP neighbors

============================================================================

Group Neighbor AdminState Sessions

----------------------------------------------------------------------------

dslam1 192.168.1.2 Enabled 0

dslam1 192.168.1.3 Enabled 0

----------------------------------------------------------------------------

Number of neighbors shown: 2

============================================================================

A:active>show>service>id>gsmp#

A:active>show>service>id>gsmp# neighbors group dslam1 192.168.1.2

============================================================================

GSMP neighbors

============================================================================

Group Neighbor AdminState Sessions

----------------------------------------------------------------------------

dslam1 192.168.1.2 Enabled 0

============================================================================

A:active>show>service>id>gsmp#

sessions

Syntax

sessions [group name] neighbor ip-address] [port port-number] [association] [statistics]

Context

show>service>id>gsmp

Description

This command displays GSMP sessions information.

Parameters

group

A GSMP group defines a set of GSMP neighbors which have the same properties.

name

Specifies a GSMP group name is unique only within the scope of the service in which it is defined.

ip-address

Specifies the ip-address of the neighbor.

port

Specifies the neighbor TCP port number use for this ANCP session.

Values

0 — 65535

association

Displays to what object the ANCP-string is associated.

statistics

Displays statistics information about an ANCP session known to the system.

Sample Output

This show command gives information about the open TCP connections with DSLAMs.

A:active>show>service>id>gsmp# sessions

=======================================================

GSMP sessions for service 999 (VPRN)

=======================================================

Port Ngbr-IpAddr Gsmp-Group

-------------------------------------------------------

40590 192.168.1.2 dslam1

-------------------------------------------------------

Number of GSMP sessions : 1

=======================================================

A:active>show>service>id>gsmp#

A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590

=========================================================================

GSMP sessions for service 999 (VPRN), neighbor 192.168.1.2, Port 40590 =========================================================================

State : Established

Peer Instance : 1 Sender Instance : a3cf58

Peer Port : 0 Sender Port : 0

Peer Name : 12:12:12:12:12:12 Sender Name : 00:00:00:00:00:00

timeouts : 0 Max. Timeouts : 3

Peer Timer : 100 Sender Timer : 100

Capabilities : DTD OAM

Conf Capabilities : DTD OAM

Priority Marking : dscp nc2

Local Addr. : 192.168.1.4

Conf Local Addr. : N/A

=========================================================================

A:active>show>service>id>gsmp#

A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 association

===============================================================================

ANCP-Strings

===============================================================================

ANCP-String Assoc. State

-------------------------------------------------------------------------------

No ANCP-Strings found

===============================================================================

A:active>show>service>id>gsmp#

A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 statistics

===============================================================

GSMP session stats, service 999 (VPRN), neighbor 192.168.1.2, Port 40590 ===============================================================

Event Received Transmitted

---------------------------------------------------------------

Dropped 0 0

Syn 1 1

Syn Ack 1 1

Ack 14 14

Rst Ack 0 0

Port Up 0 0

Port Down 0 0

OAM Loopback 0 0

===============================================================

A:active>show>service>id>gsmp#

Note: The association command gives an overview of each ANCP string received from this session.

A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 association

===============================================================================

ANCP-Strings

===============================================================================

ANCP-String Assoc.

State

-------------------------------------------------------------------------------

7330-ISAM-E47 atm 1/1/01/01:19425.64048 ANCP Up

-------------------------------------------------------------------------------

Number of ANCP-Strings : 1

===============================================================================

A:active>show>service>id>gsmp#

host

Syntax

host

Context

show>service>id

Description

Displays static hosts configured for this IES service.

Output

Show All Service-ID Output

The following table describes the show all service-id command output fields.

Label

Description

Service Id

The service identifier.

VPN Id

The number which identifies the VPN.

Service Type

Specifies the type of service.

SDP Id

The SDP identifier.

Description

Generic information about the service.

Customer Id

The customer identifier.

Last Mgmt Change

The date and time of the most recent management-initiated change to this customer.

SAP Count

The number of SAPs specified for this service.

Sample Output
*A:ALA-48# show service id 88  host
===============================================================================
Static Hosts for service 88
===============================================================================
Sap                         IP Address      Configured MAC    Dynamic MAC
  Subscriber                                                    Fwding state
-------------------------------------------------------------------------------
1/2/4:50/5                  143.144.145.1   N/A               N/A
   N/A                                                          Fwding
-------------------------------------------------------------------------------
Number of static hosts : 1
===============================================================================
*A:ALA-48#
host-connectivity-verify

Syntax

host-connectivity-verify statistics [sap sap-id]

Context

show>service>id

Description

Displays host connectivity check statistics.

Parameters

statistics

Displays host connectivity verification data.

sap sap-id

See Common CLI Command Descriptions for command syntax.

Output

Show Service Id Host Connectivity Verify

The following table describes show service-id host connectivity verification output fields:

Label

Description

Svc Id

The service identifier.

SapId/SdpId

The SAP and SDP identifiers.

DestIp Address

The destination IP address.

Last Response

The time when the last response was received.

Time Expired

Displays whether the interval value has expired.

Oper State

Displays the current operational state of the service.

Sample Output
A:ALA-48>show>service>id# host-connectivity-verify statistics sap 1/1/9:0
==============================================================================
Host connectivity check statistics
==============================================================================
Svc   SapId/          DestIp          Last                   Time 	Oper
Id    SdpId           Address         Response               Expired 	State
------------------------------------------------------------------------------
1000  551/2/3:0       143.144.145.1 	Up
==============================================================================
A:ALA-48>show>service>id#
interface

Syntax

interface [ip-address | ip-int-name] [interface-type] [detail] [family]

Context

show>service>id

Description

This command displays information for the IP interfaces associated with the IES service. If no optional parameters are specified, a summary of all IP interfaces associated to the service are displayed.

Parameters

ip-address

The IP address of the interface for which to display information.

Values

ipv4-address: a.b.c.d (host bits must be 0)
ipv6-address: x:x:x:x:x:x:x:x (eight 16-bit pieces)
x:x:x:x:x:x:d.d.d.d
x: [0 — FFFF]H
d: [0 — 255]

ip-int-name

Specifies the IP interface name for which to display information.

Values

32 characters maximum

family

Displays the router IP interface table to display.

Values

ipv4 — Displays only those peers that have the IPv4 family enabled.
ipv6 — Displays the peers that are IPv6-capable.

interface-type

Specifies to display either group or interfaces.

Values

group, subscriber

detail

Displays detailed IP interface information.

Default

IP interface summary output.

Output

Show Service-ID

The following table describes show service-id output fields.

Label

Description

If Name

The name used to refer to the IES interface.

Type

Specifies the interface type.

IP-Address

Specifies the IP address/IP subnet/broadcast address of the interface.

Adm

The administrative state of the interface.

Opr

The operational state of the interface.

Admin State

The administrative state of the interface.

Oper State

The operational state of the interface.

IP Addr/mask

Specifies the IP address/IP subnet/broadcast address of the interface.

If Index

The index corresponding to this IES interface. The primary index is 1; all IES interfaces are defined in the base virtual router context.

If Type

Specifies the interface type.

SAP Id

Specifies the SAP’s port ID.

SNTP B.Cast

Specifies whether SNTP broadcast client mode is enabled or disabled.

Arp Timeout

Specifies the timeout for an ARP entry learned on the interface.

MAC Address

Specifies the 48-bit IEEE 802.3 MAC address.

ICMP Mask Reply

Specifies whether ICMP mask reply is enabled or disabled.

Cflowd

Specifies whether Cflowd collection and analysis on the interface is enabled or disabled.

Redirects

Specifies the rate for ICMP redirect messages.

Unreachables

Specifies the rate for ICMP unreachable messages.

TTL Expired

Specifies the rate for ICMP TTL messages.

Sample Output
A:ALA-49# show service id 88 interface
===============================================================================
Interface Table
===============================================================================
Interface-Name                   Adm         Opr(v4/v6)  Type    Port/SapId
   IP-Address                                                    PfxState
-------------------------------------------------------------------------------
Sector A                         Up          Down/Down   IES     1/1/1.2.2
   -                                                             -
test                             Up          Down/Down   IES     1/1/2:0
   1.1.1.1/31                                                    n/a
   1.1.1.1/31                                                    n/a
   1.1.2.1/31                                                    n/a
test27                           Up          Up/--       IES Sub subscriber
   192.168.10.21/24                                              n/a
grp-if                           Up          Down/--     IES Grp 1/2/2
Interfaces : 4
===============================================================================
A:ALA-49#
labels

Syntax

labels

Context

show>service>id

Description

Displays the labels being used by the service.

Output

Show Service-ID Labels

The following table describes show service-id labels output fields:

Label

Description

Svc Id

The service identifier.

Sdp Id

The SDP identifier.

Type

Indicates whether the SDP is a spoke or a mesh.

I.Lbl

The VC label used by the far-end device to send packets to this device in this service by the SDP.

E.Lbl

The VC label used by this device to send packets to the far-end device in this service by the SDP.

Sample Output
*A:ALA-12# show service id 1 labels
============================================================================== 
Martini Service Labels                                                          
============================================================================== 
Svc Id     Sdp Id             Type I.Lbl        E.Lbl                           
------------------------------------------------------------------------------ 
1          10:1               Mesh 0            0                               
1          20:1               Mesh 0            0                               
1          30:1               Mesh 0            0                               
1          40:1               Mesh 130081       131061                          
1          60:1               Mesh 131019       131016                          
1          100:1              Mesh 0            0                               
------------------------------------------------------------------------------ 
Number of Bound SDPs : 6                                                       
------------------------------------------------------------------------------ 
*A:ALA-12#
sap

Syntax

sap sap-id [detail]

Context

show>service>id

Description

Displays information for the SAPs associated with the service.

If no optional parameters are specified, a summary of all associated SAPs is displayed.

Parameters

sap-id

The ID that displays SAPs for the service in the slot/mda/port[.channel format. See Common CLI Command Descriptions for command syntax.

detail

Displays detailed information for the SAP.

Output

Show Service-ID SAP

The following table describes show service SAP fields:

Label

Description

Service Id

The service identifier.

SAP

The type of SAP.

Encap

The encapsulation type of the SAP.

Ethertype

Specifies an Ethernet type II Ethertype value.

Admin State

The administrative state of the SAP.

Oper State

The operational state of the SAP.

Flags

Specifies the conditions that affect the operating status of this SAP.

Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch,RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, SapIngressNamedPoolMismatch, SapEgressNamedPoolMismatch, NoSapEpipeRingNode.

Last Status Change

Specifies the time of the most recent operating status change to this SAP.

Last Mgmt Change

Specifies the time of the most recent management-initiated change to this SAP.

Admin MTU

The desired largest service frame size (in octets) that can be transmitted through the SAP to the far-end router, without requiring the packet to be fragmented.

Ingress qos-policy

The ingress QoS policy ID assigned to the SAP.

Egress qos-policy

The egress QoS policy ID assigned to the SAP.

Ingress Filter-Id

The ingress filter policy ID assigned to the SAP.

Egress Filter-Id

The egress filter policy ID assigned to the SAP.

Acct. Pol

The accounting policy ID assigned to the SAP.

Collect Stats

Specifies whether statistics collection is enabled.

Dropped

The number of packets and octets dropped due to SAP state, ingress MAC or IP filter, same segment discard, bad checksum, etc.

Off. HiPrio

The number of high priority packets and octets, as determined by the SAP ingress QoS policy.

Off. LowPrio

The number of low priority packets and octets, as determined by the SAP ingress QoS policy.

Off. Uncolor

The number of uncolored packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

Dro. HiPrio

The number of high priority packets and octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

Dro. LowPrio

The number of low priority packets and octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

For. InProf

The number of in-profile packets and octets (rate below CIR) forwarded by the ingress Qchip.

For. OutProf

The number of out-of-profile packets and octets (rate below CIR) forwarded by the ingress Qchip.

Dro. InProf

The number of in-profile packets and octets discarded by the egress Qchip due to MBS exceeded, buffer pool limit exceeded, etc.

Ingress TD Profile

The profile ID applied to the ingress SAP.

Egress TD Profile

The profile ID applied to the egress SAP.

Alarm Cell Handling

The OAM operational status of the VCL.

AAL-5 Encap

The AAL-5 encapsulation type.

Mult Svc Site

Specifies the customer’s multi-service-site name.

I. Sched Pol

The ingress scheduler policy applied to the customer’s multi-service-site.

E. Sched Pol

The egress scheduler policy applied to the customer’s multi-service-site.

Sample Output
A:ALA-49# show service id 88 sap 7/1/1.2.2
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id         : 88
SAP                : 1/1/1.2.2                Encap             : bcpNull
Admin State        : Up                       Oper State        : Down
Flags              : PortOperDown
                     SapEgressQoSMismatch
Last Status Change : 06/06/2006 08:22:07
Last Mgmt Change   : 06/06/2006 14:15:58
Admin MTU          : 1518                     Oper MTU          : 1518
Ingress qos-policy : 2                        Egress qos-policy : 1020
Shared Q plcy      : default                  Multipoint shared : Enabled
Ingress Filter-Id  : n/a                      Egress Filter-Id  : n/a
tod-suite          : None
Multi Svc Site     : None
Acct. Pol          : None                     Collect Stats     : Disabled
Anti Spoofing      : None                     Nbr Static Hosts  : 0
-------------------------------------------------------------------------------
Subscriber Management
-------------------------------------------------------------------------------
Admin State        : Down                     MAC DA Hashing    : False
Def Sub-Profile    : None
Def SLA-Profile    : None
Sub-Ident-Policy   : None
Subscriber Limit   : 1
Single-Sub-Parameters
 Prof Traffic Only : False
 Non-Sub-Traffic   : N/A
===============================================================================
A:ALA-49#
sdp

Syntax

sdp [{sdp-id | far-end ip-address }] [detail]]

Context

show>service>id

Description

Displays information for the SDPs associated with the service.

If no optional parameters are specified, a summary of all associated SDPs is displayed.

Parameters

sdp-id

The SDP ID for which to display information.

Values

1 — 17407

far-end ip-address

When specified, displays SDP having the specified far-end IP address.

detail

Displays detailed information for the SDP.

Sample Output
A:Dut-A# show service id 1 sdp detail 
===============================================================================
Services: Service Destination Points Details 
===============================================================================
 Sdp Id 1:1  -(10.20.1.2)  
-------------------------------------------------------------------------------
Description     : Default sdp description
SDP Id             : 1:1                      Type              : Spoke        
VC Type            : Ether                    VC Tag            : n/a          
Admin Path MTU     : 0                        Oper Path MTU     : 9186         
Far End            : 10.20.1.2                Delivery          : MPLS         
 
Admin State        : Up                       Oper State        : Up           
Acct. Pol          : None                     Collect Stats     : Disabled     
Ingress Label      : 2048                     Egress Label      : 2048         
Ing mac Fltr       : n/a                      Egr mac Fltr      : n/a          
Ing ip Fltr        : n/a                      Egr ip Fltr       : n/a          
Ing ipv6 Fltr      : n/a                      Egr ipv6 Fltr     : n/a          
Admin ControlWord  : Not Preferred            Oper ControlWord  : False        
Last Status Change : 05/31/2007 00:45:43      Signaling         : None         
Last Mgmt Change   : 05/31/2007 00:45:43                                       
Class Fwding State : Up                                                        
Flags              : None
Peer Pw Bits       : None
Peer Fault Ip      : None                                                      
Peer Vccv CV Bits  : None
Peer Vccv CC Bits  : None
Max Nbr of MAC Addr: No Limit                 Total MAC Addr    : 0            
Learned MAC Addr   : 0                        Static MAC Addr   : 0            
 
MAC Learning       : Enabled                  Discard Unkwn Srce: Disabled     
MAC Aging          : Enabled                                                   
L2PT Termination   : Disabled                 BPDU Translation  : Disabled     
MAC Pinning        : Disabled                                                  
 
KeepAlive Information :
Admin State        : Disabled                 Oper State        : Disabled     
Hello Time         : 10                       Hello Msg Len     : 0            
Max Drop Count     : 3                        Hold Down Time    : 10           
 
Statistics            :
I. Fwd. Pkts.      : 0                        I. Dro. Pkts.     : 0            
I. Fwd. Octs.      : 0                        I. Dro. Octs.     : 0            
E. Fwd. Pkts.      : 0                        E. Fwd. Octets    : 0            
MCAC Policy Name   :                                                           
MCAC Max Unconst BW: no limit                 MCAC Max Mand BW  : no limit     
MCAC In use Mand BW: 0                        MCAC Avail Mand BW: unlimited    
MCAC In use Opnl BW: 0                        MCAC Avail Opnl BW: unlimited    
 
Associated LSP LIST :
Lsp Name           : A_B_1                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m35s                                                 
 
Lsp Name           : A_B_2                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m35s                                                 
 
Lsp Name           : A_B_3                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s                                                 
 
Lsp Name           : A_B_4                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s                                                 
 
Lsp Name           : A_B_5                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s                                                 
 
Lsp Name           : A_B_6                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s                                                 
 
Lsp Name           : A_B_7                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s                                                 
 
Lsp Name           : A_B_8                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m35s                                                 
 
Lsp Name           : A_B_9                                                     
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s                                                 
 
Lsp Name           : A_B_10                                                    
Admin State        : Up                       Oper State        : Up           
Time Since Last Tr*: 00h26m34s 
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding   : enabled                                                   
Default LSP        : A_B_10                   Multicast LSP     : A_B_9 
===============================================================================
FC Mapping Table
===============================================================================
FC Name             LSP Name                                                   
-------------------------------------------------------------------------------
af                  A_B_3                                                      
be                  A_B_1                                                      
ef                  A_B_6                                                      
h1                  A_B_7                                                      
h2                  A_B_5                                                      
l1                  A_B_4                                                      
l2                  A_B_2                                                      
nc                  A_B_8                                                      
===============================================================================
Stp Service Destination Point specifics
-------------------------------------------------------------------------------
Mac Move           : Blockable                                                 
Stp Admin State    : Up                       Stp Oper State    : Down         
Core Connectivity  : Down                                                      
Port Role          : N/A                      Port State        : Forwarding   
Port Number        : 2049                     Port Priority     : 128          
Port Path Cost     : 10                       Auto Edge         : Enabled      
Admin Edge         : Disabled                 Oper Edge         : N/A          
Link Type          : Pt-pt                    BPDU Encap        : Dot1d        
Root Guard         : Disabled                 Active Protocol   : N/A          
Last BPDU from     : N/A                                                       
Designated Bridge  : N/A                      Designated Port Id: 0            
 
Fwd Transitions    : 0                        Bad BPDUs rcvd    : 0            
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0            
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0            
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0            
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
A:Dut-A# 
subscriber-hosts

Syntax

subscriber-hosts [sap sap-id] [ip ip-address[/mask]] [mac ieee-address] [sub-profile sub-profile-name] [sla-profile sla-profile-name] [detail]

Context

show>service>id

Description

Displays subscriber host information.

Parameters

sap sap-id

Displays the specified subscriber host SAP information. See Common CLI Command Descriptions for command syntax.

ip-address/mask

The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation.

Values

Allowed values are IP addresses in the range 1.0.0.0 – 223.255.255.255 (with support of /31 subnets).
mask: 1 — 32

ieee-address

Specifies the 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.

sub-profile sub-profile-name

Specifies an existing subscriber profile name to be associated with the static subscriber host. The subscriber profile is configured in the config>subscr-mgmt>sub-profile context.

sla-profile sla-profile-name

Specifies an existing SLA profile name to be associated with the static subscriber host. The SLA profile is configured in the config>subscr-mgmt>sla-profile context.

detail

Displays detailed information.

statistics

Syntax

statistics [ip-int-name | ip-address]

Context

show>router>dhcp

Description

Display statistics for DHCP relay and DHCP snooping. If no IP address or interface name is specified, then all configured interfaces are displayed. If an IP address or interface name is specified, then only data regarding the specified interface is displayed.

Parameters

ip-int-name | ip-address

Displays statistics for the specified IP interface.

Output

Show DHCP Statistics Output

The following table describes the output fields for DHCP.i

Label

Description

Received Packets

The number of packets received from the DHCP clients.

Transmitted Packets

The number of packets transmitted to the DHCP clients.

Received Malformed Packets

The number of malformed packets received from the DHCP clients.

Received Untrusted Packets

The number of untrusted packets received from the DHCP clients.

Client Packets Discarded

The number of packets received from the DHCP clients that were discarded.

Client Packets Relayed

The number of packets received from the DHCP clients that were forwarded.

Client Packets Snooped

The number of packets received from the DHCP clients that were snooped.

Server Packets Discarded

The number of packets received from the DHCP server that were discarded.

Server Packets Relayed

The number of packets received from the DHCP server that were forwarded.

Server Packets Snooped

The number of packets received from the DHCP server that were snooped.

Sample Output
*A:ALA-1# show router dhcp statistics
================================================================
DHCP Global Statistics
================================================================
Rx Packets                        : 0
Tx Packets                        : 0
Rx Malformed Packets              : 0
Rx Untrusted Packets              : 0
Client Packets Discarded          : 0
Client Packets Relayed            : 0
Client Packets Snooped            : 0
Server Packets Discarded          : 0
Server Packets Relayed            : 0
Server Packets Snooped            : 0
================================================================
*A:ALA-1#
summary

Syntax

summary

Context

show>router>dhcp

Description

This command displays the status of the DHCP relay and DHCP snooping functions on each interface.

Output

Show DHCP Summary Output

The following table describes the output fields for DHCP summary.

Label

Description

Interface Name

Name of the router interface.

SapId/Sdp

Specifies the associated SAP ID or SDP ID.

Arp Populate

Specifies whether or not ARP populate is enabled.

Used/Provided

Used

The number of lease-states currently in use on a specific interface (the number of clients on that interface got an IP address by DHCP). This value is always less than or equal to the ‘Provided’ field.

Provided

The configured for a specific interface.

Info Option

Indicates whether Option 82 processing is enabled on the interface.

Admin State

Indicates the administrative state.

Sample Output
A:ALA-49# show router dhcp summary
===============================================================================
DHCP Summary (Router: Base)
===============================================================================
Interface Name                   Arp      Used/                 Info    Admin
  SapId/Sdp                      Populate Provided              Option  State
-------------------------------------------------------------------------------
Sector A                         No       0/0                   Keep    Up
  sap:7/1/1.2.2                           0/0
grp-if                           No       0/1                   Keep    Down
ies-test                         No       0/0                   Keep    Up
  sap:9/1/2:0/500                         0/0
test                             No       0/0                   Keep    Up
  sap:10/1/2:0                            0/0
test1                            No       0/0                   Keep    Up
  sap:7/1/1.1.2                           0/0
test2                            No       0/0                   Keep    Up
  sap:7/1/1.2.1                           0/0
testA                            No       0/0                   Keep    Up
  sap:7/1/3.1.1                           0/0
testB                            No       0/0                   Keep    Up
  sap:7/1/5.1.1                           0/0
to-HQ                            No       0/0                   Keep    Up
  sdp:spoke-2:1001                        0/0
to-web                           No       0/0                   Keep    Up
  sap:2/1/10:50                           0/0
-------------------------------------------------------------------------------
Interfaces: 9
vrrp

Syntax

vrrp

Context

show>router

Description

This command displays information VRRP instances.

instance

Syntax

instance

instance interface interface-name [vrid virtual-router-id]

instance interface interface-name vrid virtual-router-id ipv6

Context

show>router>vrrp

Description

This command displays statistics for the VRRP instance.

Parameters

interface-name

Displays statistics for the specified interface.

virtual-router-id

Displays statistics for the specified virtual router ID.

Values

1 — 255

statistics

Syntax

statistics

Context

show>router>vrrp

Description

This command displays statistics for the VRRP instance.

retailers

Syntax

retailers

Context

show>service>id

Description

This command displays the service ID of the retailer subscriber service to which this DHCP lease belongs.

wholesalers

Syntax

wholesalers

Context

show>service>id

Description

This command displays service wholesaler information.

IES Clear Commands

dhcp

Syntax

dhcp

Context

clear>router>dhcp

clear>service>id

Description

This command enables the context to clear DHCP parameters.

dhcp6

Syntax

dhcp6

Context

clear>router>dhcp6

clear>service>id

Description

This command enables the context to clear DHCPv6 parameters.

statistics

Syntax

statistics [ip-int-name | ip-address]

Context

clear>router>dhcp

Description

Clears DHCP statistics.

id

Syntax

id service-id

Context

clear>service

clear>service>statistics

Description

This command clears parameters for a specific service.

Parameters

service-id

The ID that uniquely identifies the service to clear.

arp-host

Syntax

arp-host

arp-host { mac ieee-address | sap sap-id | ip-address ip-address[/mask] }

arp-host [port port-id] [inter-dest-id intermediate-destination-id | no-inter-dest-id]

arp-host statistics [sap sap-id | interface interface-name]

Context

clear>service>id

Description

This command clears ARP host data.

interface

Syntax

interface [ip-int-name | ip-addr] [icmp]

Context

clear>router

Description

This command clears IP interface statistics.

If no IP interface is specified either by IP interface name or IP address, the command will perform the clear operation on all IP interfaces.

Parameters

ip-int-name | ip-addr

The IP interface name or IP interface address.

Default

All IP interfaces.

icmp

Specifies to reset the ICMP statistics for the IP interface(s) used for ICMP rate limit.

interface

Syntax

interface interface-name [vrid virtual-router-id]

interface interface-name vrid vritual-router-id ipv6

Context

clear>router>vrrp

Description

This command clears and resets VRRP instances.

Parameters

interface-name

Specifies an existing interface name up to 32 characters in length.

virtual-router-id

Specifies the virtual router identifier.

Values

1 — 255

statistics

Syntax

statistics interface interface-name [vrid virtual-router-id]

statistics

statistics interface interface-name vrid virtual-router-id ipv6

Context

clear>router>vrrp

Description

This command clears statistics for VRRP instances.

Parameters

interface-name

Specifies an existing interface name up to 32 characters in length.

virtual-router-id

Specifies the virtual router identifier.

Values

1 — 255

fdb

Syntax

fdb {all | mac ieee-address | sap sap-id] | mesh-sdp sdp-id[:vc-id] | spoke-sdp sdp-id:vc-id}

Context

clear>service>id

Description

This command clears FDB entries for the service.

Parameters

all

Clears all FDB entries.

mac ieee-address

Clears only FDB entries in the FDB table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.

sap sap-id

Clears the specified SAP information. See Common CLI Command Descriptions for command syntax.

mesh-sdp

Clears only service FDB entries associated with the specified mesh SDP ID. For a mesh SDP, the VC ID is optional.

spoke-sdp

Clears only service FDB entries associated with the specified spoke SDP ID. For a spoke SDP, the VC ID must be specified.

sdp-id

The SDP ID for which to clear associated FDB entries.

Values

1 — 17407

vc-id

The virtual circuit ID on the SDP ID for which to clear associated FDB entries.

Default

For mesh SDPs only, all VC IDs.

Values

1 — 4294967295

site

Syntax

site service-id

Context

clear>service>id

Description

This command clears site-specific information for the service.

Parameters

service-id

Specifies the service ID or service name up to 64 characters in length.

Values

1 — 2147483648

spoke-sdp

Syntax

spoke-sdp sdp-id:vc-id ingress-vc-label

Context

clear>service>id

Description

Clears and resets the spoke SDP bindings for the service.

Parameters

sdp-id

The spoke SDP ID to be reset.

Values

1 — 17407

vc-id

The virtual circuit ID on the SDP ID to be reset.

Values

1 — 4294967295

stp

Syntax

stp

Context

clear>service>statistics>id

Description

Clears all spanning tree statistics for the service ID.

lease-state

Syntax

lease-state

lease-state ip-address ip-address

lease-state mac ieee-address

lease-state sap sap-id

lease-state sdp sdp-id:vc-id

Context

clear>service>id>dhcp

Description

Clears DHCP lease state information for this service.

Parameters

ip-address

The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation. Allowed values are IP addresses in the range 1.0.0.0 – 223.255.255.255 (with support of /31 subnets).

ieee-address

Specifies the 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.

sap sap-id

Clears the specified lease state SAP information. See Common CLI Command Descriptions for command syntax.

sdp-id

The specified SDP to be cleared.

Values

1 — 17407

vc-id

The virtual circuit ID on the SDP ID to be cleared.

Values

1 — 4294967295

lease-state

Syntax

lease-state [ip-address ipv6-address/prefix-length] [mac ieee-address]

Context

clear>service>id>dhcp6

Description

This command clears DHCPv6 lease state information for this service.

Parameters

ip-address ipv6-address/prefix-length

The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation. Allowed values are IP addresses in the range 1.0.0.0 – 223.255.255.255 (with support of /31 subnets).

Values

ipv6-address x:x:x:x:x:x:x:x (eight 16-bit pieces)
x:x:x:x:x:x:d.d.d.d
x [0 — FFFF]H
d [0 — 255]D
prefix-length 1 — 128

mac ieee-address

Specifies the 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.

statistics

Syntax

statistics [ip-int-name | ipv6-address]

Context

clear>router>dhcp6

Description

This command clears DHCP6 statistics.

Parameters

ip-int-name

Specifies the IP interface name up to 32 characters inlength.

ip-address ipv6-address/prefix-length

The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation. Allowed values are IP addresses in the range 1.0.0.0 – 223.255.255.255 (with support of /31 subnets).

Values

ipv6-address x:x:x:x:x:x:x:x (eight 16-bit pieces)
x:x:x:x:x:x:d.d.d.d
x [0 — FFFF]H
d [0 — 255]D
prefix-length 1 — 128

statistics

Syntax

statistics [sap sap-id | sdp sdp-id:vc-id | interface ip-address | ip-int-name]

Context

clear>service>id>dhcp

Description

This command clears DHCP statistics.

Parameters

sap sap-id

Clears the specified SAP information. See Common CLI Command Descriptions for command syntax.

sdp sdp-id

The specified SDP to be cleared.

Values

1 — 17407

vc-id

The virtual circuit ID on the SDP ID to be cleared.

Values

1 — 4294967295

interface ip-address

The interface IP address.

ip-int-name

The interface name.

IES Debug Commands

host-connectivity-verify

Syntax

[no] host-connectivity-verify

Context

debug>service>id

Description

This command enables Subscriber Host Connectivity Verification (SHCV) debugging.

The no form of the command disables the SHCV debugging.

ip

Syntax

[no] ip ip-address

Context

debug>service>id>host-connectivity-verify

Description

This command displays Subscriber Host Connectivity Verification (SHCV) events for a particular IP address.

Parameters

ip-address

The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation. Allowed values are IP addresses in the range 1.0.0.0 – 223.255.255.255 (with support of /31 subnets).

mac

Syntax

[no] mac ieee-address

Context

debug>service>id>host-connectivity-verify

Description

This command displays Subscriber Host Connectivity Verification (SHCV) events for a particular MAC address.

Parameters

mac-address

Specifies the 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.

sap

Syntax

[no] sap sap-id

Context

debug>service>id>host-connectivity-verify

Description

This command displays Subscriber Host Connectivity Verification (SHCV) events for a particular SAP.

Parameters

sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI Command Descriptions for command syntax.

packets

Syntax

[no] packets

[no] packets interface ip-int-name [vrid virtual-router-id]

[no] packets interface ip-int-name vrid virtual-router-id ipv6

Context

debug>router>vrrp

Description

This command enables or disables debugging for VRRP packets.

Parameters

ip-int-name

Specifies the interface name.

virtual-router-id

Specifies the router ID.

Values

1 — 255

events

Syntax

[no] events

[no] events interface ip-int-name [vrid virtual-router-id]

[no] events interface ip-int-name vrid virtual-router-id ipv6

Context

debug>router>vrrp

Description

This command enables or disables debugging for VRRP events.

Parameters

ip-int-name

Specifies the interface name.

virtual-router-id

Specifies the router ID.

Values

1 — 255

instance

Syntax

instance interface interface-name vr-id virtual-router-id [ipv6] [interval seconds] [repeat repeat] [absolute|rate]

Context

monitor>router>vrrp

Description

This command enables monitoring for statistics for VRRP instances.

Label	Description
Customer-ID	The ID that uniquely identifies a customer.
Contact	The name of the primary contact person.
Description	Generic information about the customer.
Phone	The phone/pager number to reach the primary contact person.
Total Customers	The total number of customers configured.
Multi-service site
Site	Multi-service site name. A multi-service customer site is a group of SAPs with common origination and termination points.
Description	Information about a specific customer's multi-service site.
Assignment	The port ID, MDA, or card number, where the SAP's that are members of this multi- service site are defined.
I. Sched Pol	The ingress QoS scheduler policy assigned to this multi-service site.
E. Sched Pol	The egress QoS scheduler policy assigned to this multi-service site.
Service Association
Service-ID	The ID that uniquely identifies a service.
SAP	Specifies the SAP assigned to the service.

Label	Description
Svc Id	The value that identifies a service.
Sdp Id	The value that identifies a SDP.
Type	Indicates whether the SDP binding is a spoke or a mesh.
I. Lbl	The VC label used by the far-end device to send packets to this device in this service by the SDP.
E. Lbl	The VC label used by this device to send packets to the far-end device in this service by the SDP.
Number of bindings found	The total number of SDP bindings that exist within the specified egress label range.

Label	Description
Port ID	The ID of the access port where the SAP is defined.
Svc ID	The value that identifies the service.
SapMTU	The SAP MTU value.
Igr.QoS	The SAP ingress QoS policy number specified on the ingress SAP.
Ing.Fltr	The MAC or IP filter policy ID applied to the ingress SAP.
E.QoS	The SAP egress QoS policy number specified on the egress SAP.
Egr.Fltr	The MAC or IP filter policy ID applied to the egress SAP.
A.Pol	The accounting policy ID assigned to the SAP.
Adm	The administrative state of the SAP.
Opr	The actual state of the SAP.

Label	Description
Service Id	The value that identifies the service.
Type	Specifies the service type configured for the service ID.
Adm	The administrative state of the service.
Opr	The operating state of the service.
CustomerID	The ID of the customer who owns this service.
Last Mgmt Change	The date and time of the most recent management-initiated change to this service.

Label	Description
Service Detailed Information
Service Id	The service identifier.
VPN Id	The number which identifies the VPN.
Service Type	Specifies the type of service.
SDP Id	The SDP identifier.
Description	Generic information about the service.
Customer Id	The customer identifier.
Last Mgmt Change	The date and time of the most recent management-initiated change to this customer.
SAP Count	The number of SAPs specified for this service.
SDP Bind Count	The number of SDPs bound to this service.
Service Destination Points (SDPs)
SDP Id	The SDP identifier.
Type	Indicates whether this Service SDP binding is a spoke or a mesh.
Admin Path MTU	The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.
Oper Path MTU	The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.
Delivery	Specifies the type of delivery used by the SDP: GRE or MPLS.
Admin State	The administrative state of this SDP.
Oper State	The operational state of this SDP.
Ingress Label	The label used by the far-end device to send packets to this device in this service by this SDP.
Egress Label	The label used by this device to send packets to the far-end device in this service by this SDP.
Ingress Filter	The ID of the ingress filter policy.
Egress Filter	The ID of the egress filter policy.
Far End	Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP.
Last Changed	The date and time of the most recent change to this customer.
Signaling	Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP.
Admin State	Specifies the operating status of the service.
Oper State	The current status of the service.
Hello Time	Specifies how often the SDP echo request messages are transmitted on this SDP.
Hello Msg Len	Specifies the length of the SDP echo request messages transmitted on this SDP.
Max Drop Count	Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault.
Hold Down Time	Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state.
SDP Delivery Mechanism	When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far-end field. If the SDP type is GRE, then the following message displays: “SDP Delivery Mechanism is not MPLS”
Number of SDPs	The total number SDPs applied to this service ID.
Service Access Points
Service Id	The service identifier.
Port Id	The ID of the access port where this SAP is defined.
Description	Generic information about the SAP.
Encap	The value of the label used to identify this SAP on the access port.
Admin State	The desired state of the SAP.
Oper State	The operating state of the SAP.
Last Changed	The date and time of the last change.
Admin MTU	The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.
Oper MTU	The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.
Ingress qos-policy	The SAP ingress QoS policy ID.
Egress qos-policy	The SAP egress QoS policy ID.
Ingress Filter-Id	The SAP ingress filter policy ID.
Egress Filter-Id	The SAP egress filter policy ID.
Multi Svc Site	Indicates the multi-service site that the SAP is a member.
Ingress sched-policy	Indicates the ingress QoS scheduler for the SAP.
Egress sched-policy	Indicates the egress QoS scheduler for the SAP.
Acct. Pol	Indicates the accounting policy applied to the SAP.
Collect Stats	Specifies whether accounting statistics are collected on the SAP.
SAP Statistics
Dropped	The number of packets or octets dropped.
Offered Hi Priority	The number of high priority packets, as determined by the SAP ingress QoS policy.
Offered Low Priority	The number of low priority packets, as determined by the SAP ingress QoS policy.
Forwarded In Profile	The number of in-profile packets or octets (rate below CIR) forwarded.
Forwarded Out Profile	The number of out-of-profile packets or octets (rate above CIR) forwarded.
Queueing Stats
Dropped In Profile	The number of in-profile packets or octets discarded.
Dropped Out Profile	The number of out-of-profile packets or octets discarded.
Forwarded In Profile	The number of in-profile packets or octets (rate below CIR) forwarded.
Forwarded Out Profile	The number of out-of-profile packets or octets (rate above CIR) forwarded.
SAP per Queue stats
Ingress Queue 1	The index of the ingress QoS queue of this SAP.
High priority offered	The packets or octets count of the high priority traffic for the SAP.
High priority dropped	The number of high priority traffic packets/octets dropped.
Low priority offered	The packets or octets count of the low priority traffic.
Low priority dropped	The number of low priority traffic packets/octets dropped.
In profile forwarded	The number of in-profile packets or octets (rate below CIR) forwarded.
Out profile forwarded	The number of out-of-profile octets (rate above CIR) forwarded.
Egress Queue 1	The index of the egress QoS queue of the SAP.
In profile forwarded	The number of in-profile packets or octets (rate below CIR) forwarded.
IPCP Address Extension Details
In profile dropped	The number of in-profile packets or octets dropped for the SAP.
Peer IP Addr	Specifies the remote IP address to be assigned to the far-end of the associated PPP/MLPPP link via IPCP extensions.
Peer Pri DNS Addr	Specifies a unicast IPv4 address for the primary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions.
Peer Sec DNS Addr	Specifies a unicast IPv4 address for the secondary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions. (optional)

Label	Description
IP Address	The IP address.
MAC Address	The specified MAC address.
Type	Static FDB entries created by management. Learned Dynamic entries created by the learning process. OAM Entries created by the OAM process. Other — Local entries for the IP interfaces created.
Expiry	The age of the ARP entry.
Interface	The interface applied to the service.
SAP	The SAP ID.

Label	Description
Interface Name	Name of the router interface.
Arp Populate	Specifies whether or not ARP populate is enabled.
Used/Provided	Used The number of lease-states that are currently in use on a specific interface, that is, the number of clients on that interface got an IP address by DHCP. This value is always less than or equal to the ‘Provided’ field.
	Provided The lease-populate value that is configured for a specific interface.
Info Option	Indicates whether Option 82 processing is enabled on the interface.
Admin State	Indicates the administrative state.

Label	Description
If Name	The name used to refer to the IES interface.
Type	Specifies the interface type.
IP-Address	Specifies the IP address/IP subnet/broadcast address of the interface.
Adm	The administrative state of the interface.
Opr	The operational state of the interface.
Admin State	The administrative state of the interface.
Oper State	The operational state of the interface.
IP Addr/mask	Specifies the IP address/IP subnet/broadcast address of the interface.
If Index	The index corresponding to this IES interface. The primary index is 1; all IES interfaces are defined in the base virtual router context.
If Type	Specifies the interface type.
SAP Id	Specifies the SAP’s port ID.
SNTP B.Cast	Specifies whether SNTP broadcast client mode is enabled or disabled.
Arp Timeout	Specifies the timeout for an ARP entry learned on the interface.
MAC Address	Specifies the 48-bit IEEE 802.3 MAC address.
ICMP Mask Reply	Specifies whether ICMP mask reply is enabled or disabled.
Cflowd	Specifies whether Cflowd collection and analysis on the interface is enabled or disabled.
Redirects	Specifies the rate for ICMP redirect messages.
Unreachables	Specifies the rate for ICMP unreachable messages.
TTL Expired	Specifies the rate for ICMP TTL messages.

Label	Description
Received Packets	The number of packets received from the DHCP clients.
Transmitted Packets	The number of packets transmitted to the DHCP clients.
Received Malformed Packets	The number of malformed packets received from the DHCP clients.
Received Untrusted Packets	The number of untrusted packets received from the DHCP clients.
Client Packets Discarded	The number of packets received from the DHCP clients that were discarded.
Client Packets Relayed	The number of packets received from the DHCP clients that were forwarded.
Client Packets Snooped	The number of packets received from the DHCP clients that were snooped.
Server Packets Discarded	The number of packets received from the DHCP server that were discarded.
Server Packets Relayed	The number of packets received from the DHCP server that were forwarded.
Server Packets Snooped	The number of packets received from the DHCP server that were snooped.