The table below contains a list of each circuit pack supported by the Alcatel-Lucent 1665 DMX, indicates which slots they are able to be housed in, and in what release each circuit pack is available.
|
Circuit pack |
Apparatus code |
Slot(s) |
Release |
Comments |
|---|---|---|---|---|
|
System Controller (SYSCTL) |
LNW2 |
CTL |
6.0 |
Extended temp. controller for outside cabinet deployment (OSP hardened). |
|
28DS1PM |
LNW7 |
A–D |
1.0 |
28 ports, not supported with VLF Mains, OSP hardened |
|
56DS1/E1 |
LNW8 |
A–D |
3.1 |
56 ports, for use in Alcatel-Lucent 1665 DMX High-Capacity Shelf,E1 service is provisionable on a per pack basis, OSP hardened |
|
12DS3/EC1 |
LNW16 |
A–D |
1.1 |
12 ports, OSP hardened |
|
DS1/DS3 TransMUX |
LNW18 |
A–D |
3.0 |
12 ports, receives/transmits channelized DS3, OSP hardened |
|
48DS3/EC1 |
LNW19B |
A–D |
5.0 |
48 ports, for use in Alcatel-Lucent 1665 DMX High-Capacity Shelf, supports DS3 loopbacks, OSP hardened |
|
48DS3/EC1/ TMUX (with portless operation) |
LNW20 |
A–G |
7.0.1 |
48 ports, DS3, EC1, and TMUX functionality on a port-by-port basis. LNW20 is supported in G1/2 for portless mode only with certain Mains, OSP hardened. When Mains that don't support portless are used, LNW20 can only be installed in A–D. |
|
OC-48 OLIU |
LNW27 |
M1, M2 |
2.1 |
High-speed, long reach, 1310 nm, 48 STS-1 VT fabric |
|
OC-48 OLIU |
LNW29 |
M1, M2 |
2.1 |
High-speed, long reach, 1550 nm, 48 STS-1 VT fabric |
|
OC-48 OLIU |
LNW31 |
A–D, G1, G2 |
2.0 |
Low-speed, intermediate reach, 1310 nm, 12 STS-1 VT fabric, OSP hardened |
|
OC-48 OLIU |
LNW32 |
M1, M2 |
4.0 |
High-speed, long reach, 1310 nm, 48 STS-1 VT fabric, OSP hardened |
|
OC-3 OLIU (4 ports) |
LNW37 |
A–D, G1, G2 |
4.0 |
Low-speed, 12 STS-1 VT fabric, PTM optics, supports facility loopbacks, OSP hardened |
|
OC-3 OLIU (8 ports) |
LNW45 |
A–D, G1, G2 |
5.0 |
Low-speed, 48 STS-1 VT fabric, PTM optics, supports facility loopbacks, OSP hardened 4 |
|
OC-12 OLIU (1 port) |
LNW48 |
M1, M2 |
3.1 |
High-speed, intermediate reach. 1310 nm, 12 STS-1 VT fabric, OSP hardened |
|
OC-12 OLIU (4 ports) |
LNW49 |
A–D, G1, G2 |
4.0 |
Low-speed, 48 STS-1 VT fabric, PTM optics, OSP hardened 4 |
|
OC-12 OLIU (1 port) |
LNW50 |
M1, M2 |
3.1 |
High-speed, long reach. 1310 nm, 12 STS-1 VT fabric, OSP hardened |
|
OC-12 OLIU (1 port) |
LNW54 |
M1, M2 |
5.1 |
High-speed, long reach. 1550 nm, 12 STS-1 VT fabric, OSP hardened |
|
OC-3/OC-12/ OC-48 OLIU (12/4 ports) |
LNW55 |
A–D, G1, G2 |
7.1 |
12OC-3/12OC-12/4OC-48, PTM-based, multi-port, multi-rate (MPMR), for use with VLF Main packs, supports facility loopbacks, OSP hardened 4 |
|
OC-192 OLIU |
LNW56 |
M1, M2 |
2.1 |
High-speed, intermediate reach, 1550 nm, 48 STS-1 VT fabric |
|
OC-192 OLIU |
LNW58 |
M1, M2 |
2.1 |
High-speed, very short reach, 1310 nm, 48 STS-1 VT fabric |
|
OC-192 OLIU |
LNW59 |
M1, M2 |
7.0 |
2 port, High-speed, 1.3SR1/1.5IR2/1.5LR2 and DWDM PTMs, 20G optical main, 240G STS fabric, 30G VT termination capacity, and 40G VT fabric |
|
OC-48 OLIU |
LNW62 |
A–D, G1, G2 |
7.0 |
4 port, Low-speed, SR, 1.3LR1, 1.5LR2, and DWDM PTMs, no switch fabric, requires use of VLF Main, OSP hardened 4 |
|
1000BASE-SX/LX/ZX (4 ports) Private Line |
LNW63 |
A–G 1 |
6.0 |
1000BASE-SX/LX/ZX Ethernet interface via optical PTMs, can be used in slot 1 and/or 2 in a VLF-equipped Alcatel-Lucent 1665 DMX and either slot 1 or 2 in a non-VLF equipped Alcatel-Lucent 1665 DMX, GbE private lines, includes no switch fabric, OSP hardened 4 |
|
1000BASE-T/SX/LX/ZX (8 ports) Private Line |
LNW64 |
A–G 1 |
7.0 |
1000BASE-T/SX/LX/ZX Ethernet interface via PTMs, can be used in slot 1 and/or 2 in a VLF-equipped Alcatel-Lucent 1665 DMX, GbE private lines, includes no switch fabric, OSP hardened 4 |
|
10/100T (24 ports) |
LNW66 |
A–D 2 |
1.1 |
100BASE-T Ethernet interface |
|
FC-DATA (SAN Interface) |
LNW73 |
A–G 1 |
5.1 |
4 ports, PTM optics supporting either FICON/Fibre-Channel or ESCON, can be installed in slot 1 or 2 of a function group or a growth slot with VLF mains, slot 1 only with non-VLF |
|
FC-DATA w/ compression (SAN Interface) |
LNW73C |
A–G 1 |
7.0 |
4 ports, PTM optics supporting either FICON/Fibre-Channel or ESCON, also supports compression of SAN traffic, can be installed in slot 1 or 2 of a function group or a growth slot with VLF mains, slot 1 only with non-VLF |
|
100BASE-ZX/LX/FX (8 ports) 10/100BASE-T (16 ports) Private Line |
LNW74 |
A–G 1 |
5.0 |
Hybrid 100BASE-ZX/LX/FX and 10/100 BASE-T Ethernet interface, may only occupy slot 1 of a function group or a growth slot if non-VLF mains are used, slot 1 and 2 are available with VLF mains (Series 1:2 or higher LNW74s), uses PTM optics for ZX/LX/FX interfaces, supports private lines, when installed in the Growth slots, only the optical ports are functional (17–24), OSP hardened. 4 |
|
OC-48 OLIU |
LNW76 |
M1, M2 |
2.1 |
High-speed, short reach, 1310 nm, 48 STS-1 VT fabric |
|
Main Switch Pack |
LNW80 |
M1, M2 |
4.0 |
High-speed, 96 STS-1 VT fabric, based on LNW27, no optics on pack, OSP hardened |
|
OC-3/OC-12/ OC48 OLIU (8/8/2 ports) |
LNW82 |
M1, M2 |
7.1 |
8OC-3/8OC-12/2OC-48 multi-port multi-rate (MPMR) PTM-based pack, 7.5G VT capacity, supports facility loopbacks, OSP hardened 4 |
|
100/ 1000BASE-T 100BASE- ZX/LX/FX (4 ports) FE/GBE PL |
LNW87 |
A–G 1 |
9.0 |
100/1000BASE-T and 100BASE-ZX/LX/FX Ethernet interface via optical PTMs, can be used in slot 1 and/or 2 in a VLF-equipped Alcatel-Lucent 1665 DMX and either slot 1 or 2 in a non-VLF equipped Alcatel-Lucent 1665 DMX, GbE private lines, includes no switch fabric, OSP hardened 4 |
|
In-service Electrical Continuity Test Tool |
LNW93 |
A–D |
4.0 |
For use in Alcatel-Lucent 1665 DMX to test the integrity of cables that will be connected to a High-Capacity DS1, DS3, or Ethernet circuit pack while a lower capacity pack is in-service in the other slot of the function group |
|
Electrical Continuity Test Tool |
LNW94 |
A–D |
3.1 |
For use in Alcatel-Lucent 1665 DMX to test the integrity of cables connected to the DS1, DS3, and Ethernet interfaces on the Alcatel-Lucent 1665 DMX shelf |
|
Detectable Apparatus Blank |
LNW97 |
M2 |
3.1 |
Filler plates to be used in unpopulated M2 slot of the Alcatel-Lucent 1665 DMX shelf. WaveStar® CIT will show a blank plate when slot is equipped with this pack |
|
Detectable Apparatus Blank |
LNW98 |
A–D, G1, G2 |
3.1 |
Filler plates to be used in unpopulated Function Unit or Growth Slot of the Alcatel-Lucent 1665 DMX shelf. WaveStar® CIT will show a blank plate when slot is equipped with this pack. |
|
100/1000 BASE-T or 1000BASE-LX/SX/ZX (4 ports) 100BASE-ZX/LX/FX (4 ports) |
LNW170 |
A–G 1 |
7.1 |
100/1000 4 port Ethernet Switch |
|
OC-48 OLIU |
LNW202 |
M1, M2 |
7.1 |
High-speed, PTM-based pack, 48 STS-1 VT fabric, OSP hardened 4 |
|
OC-12 OLIU |
LNW203 |
M1, M2 |
9.0 |
High-speed, PTM-based pack, 12 STS-1 VT fabric, OSP hardened 4 |
|
OC-48 OLIU |
LNW402 |
A–D, G1, G2 |
8.0 |
Low-speed, OC-48 PTM-based, 12 STS-1 VT fabric, OSP hardened 4 |
|
OC-192 OLIU |
LNW502 |
M1, M2 |
7.1 |
High-speed, PTM-based pack with 48 STS-1 VT fabric, OSP hardened 4 |
|
OC-48/OC-192 OLIU |
LNW504 |
M1, M2 |
9.0 |
4OC-48/4OC-192 PTM-based VLF Main |
|
OC-192 OLIU (1 port) |
LNW603 |
A–D, G1, G2 |
9.0 |
Low-speed, PTM-based pack for use with VLF Mains |
|
XM10G/8 |
LNW705 |
A–D, G1, G2 |
R7.1.1 |
8:1 10G Muxponder - PTM-based pack (1 XFP and up to 8 SFPs) |
|
OMD5/8 |
LNW785 |
A–D, G1, G2 |
7.1 |
8 channel low-loss DWDM Mux/Demux with integrated VOAs, ITU-T channels 52 through 59 (195.20-195.90 THz) |
|
56DS1/E1 |
LNW801 |
A–D |
8.0 |
56 ports, for use in Alcatel-Lucent 1665 DMX High-Capacity Shelf, E1 service is provisionable on a per pack basis, OSP hardened |
|
Apparatus Blank |
177D |
A–D, G1, G2 |
1.0 |
Filler plates to be used in unpopulated slots of the Alcatel-Lucent 1665 DMX shelf |
|
Apparatus Blank |
177E |
M2 |
2.0 |
Filler plates to be used in unpopulated slots of the Alcatel-Lucent 1665 DMX shelf |
In order to support Ethernet and SAN packs in both Slot 1 and 2 of a Function or Growth Group, Alcatel-Lucent 1665 DMX must be equipped with VLF Mains (LNW59/LNW82/LNW504). When the shelf is equipped non-VLF mains, the Ethernet circuit packs are only supported in Slot 1 of a group. However, when the LNW170 is in equipment-protected mode, it is supported in both slots of a group with VLF and non-VLF mains.
Alcatel-Lucent 1665 DMX does not allow installation of two packs with electrical interfaces in adjacent slots within the same Function Unit or Growth Group (other than an equipment-protected pair). Therefore, in systems equipped with VLF mains (LNW59/LNW82/LNW504), LNW66 packs can reside in either Slot 1 or Slot 2 of a group, but not both at the same time. Telcordia ® OS systems only support electrical packs in Slot 1 of a group. However, another optical (Ethernet or SONET) pack may be installed in the other slot. In non-VLF equipped shelves, LNW66 can only occupy Slot 1 of a particular group.
When populating the MAIN slots in the Alcatel-Lucent 1665 DMX shelf, it is imperative that both MAIN 1 and MAIN 2 contain circuit packs with identical VT switch fabric size. The Alcatel-Lucent 1665 DMX OC-48 circuit packs, for example, contain fabrics ranging from 12 STS-1 to VLF capacity. It is therefore very important that you look carefully at the switch fabric sizes of your high-speed circuit packs while planning your order.
These PTM-based circuit packs are OSP hardened, but they must also be equipped with OSP-hardened PTMs to operate in OSP environments.
| November 2011 | Copyright © 2011 Alcatel-Lucent. All rights reserved. |