Alcatel-Lucent 1665 DMX supports a Standard SONET PM MIB module defined in IETF RFC2558. This module defines SONET PM parameters for the SONET physical medium, section layer, line, path and tributary. This Standard SONET PM MIB module applies to individual SONET ports and tributaries.
The following table shows the Standard SONET PM MIB module parameters.
|
Group/Table |
Parameters |
Definition |
|---|---|---|
|
SonetMedium Group |
sonetMediumType (READ-ONLY) |
value: “sonet” |
|
sonetMediumTimeElapsed |
seconds since the beginning of current period | |
|
sonetMediumValidIntervals |
number of previous 15-min intervals for which data was collected (usually 32) | |
|
sonetMediumLineCoding (READ-ONLY) |
line coding,e.g., B3ZS | |
|
sonetMediumLineType (READ-ONLY) |
short range single mode or long range single mode | |
|
sonetMediumCircuitIdentifier (READ-ONLY) |
circuit ID | |
|
sonetMediumInvalidIntervals |
number of intervals for which no data is available (usually 0) | |
|
sonetMediumLoopbackConfig (READ-ONLY) |
no loopback, facility loopback or terminalloopback | |
|
SonetSectionCurrent Table |
sonetSectionCurrentStatus |
Current |
|
sonetSectionCurrentESs |
Current | |
|
sonetSectionCurrentSESs |
Current | |
|
sonetSectionCurrentSEFSs |
Current | |
|
sonetSectionCurrentCVs |
Current | |
|
SonetSectionInterval Table |
sonetSectionIntervalNumber |
15 minute |
|
sonetSectionIntervalESs |
15 minute | |
|
sonetSectionIntervalSESs |
15 minute | |
|
sonetSectionIntervalSEFSs |
15 minute | |
|
sonetSectionIntervalCVs |
15 minute | |
|
sonetSectionIntervalValidData |
15 minute | |
|
SonetLineCurrent Table |
sonetLineCurrentStatus |
Current |
|
sonetLineCurrentESs |
Current | |
|
sonetLineCurrentSESs |
Current | |
|
sonetLineCurrentCVs |
Current | |
|
sonetLineCurrentUASs |
Current | |
|
SonetLineCurrent Table |
sonetLineCurrentStatus |
Current |
|
sonetLineCurrentESs |
Current | |
|
sonetLineCurrentSESs |
Current | |
|
sonetLineCurrentCVs |
Current | |
|
sonetLineCurrentUASs |
Current | |
|
SonetLineInterval Table |
sonetLineIntervalNumber |
15 minute |
|
sonetLineIntervalESs |
15 minute | |
|
sonetLineIntervalSESs |
15 minute | |
|
sonetLineIntervalCVs |
15 minute | |
|
sonetLineIntervalUASs |
15 minute | |
|
sonetLineIntervalValidData |
15 minute | |
|
SonetFarEndLineCurrent Table |
sonetFarEndLineCurrentESs |
Current |
|
sonetFarEndLineCurrentSESs |
Current | |
|
sonetFarEndLineCurrentCVs |
Current | |
|
sonetFarEndLineCurrentUASs |
Current | |
|
SonetFarEndLineInterval Table |
sonetFarEndLineIntervalNumber |
15 minute |
|
sonetFarEndLineIntervalESs |
15 minute | |
|
sonetFarEndLineIntervalSESs |
15 minute | |
|
sonetFarEndLineIntervalCVs |
15 minute | |
|
sonetFarEndLineIntervalUASs |
15 minute | |
|
sonetFarEndLineIntervalValidData |
15 minute | |
|
SonetPathCurrent Table |
sonetPathCurrentWidth |
Current |
|
sonetPathCurrentStatus |
Current | |
|
sonetPathCurrentESs |
Current | |
|
sonetPathCurrentSESs |
Current | |
|
sonetPathCurrentCVs |
Current | |
|
sonetPathCurrentUASs |
Current | |
|
SonetPathInterval Table |
sonetPathIntervalNumber |
15 minute |
|
sonetPathIntervalESs |
15 minute | |
|
sonetPathIntervalSESs |
15 minute | |
|
sonetPathIntervalCVs |
15 minute | |
|
sonetPathIntervalUASs |
15 minute | |
|
sonetPathIntervalValidData |
15 minute | |
|
SonetFarEndPathCurrent Table |
sonetFarEndPathCurrentESs |
Current |
|
sonetFarEndPathCurrentSESs |
Current | |
|
sonetFarEndPathCurrentCVs |
Current | |
|
sonetFarEndPathCurrentUASs |
Current | |
|
SonetFarEndPathInterval Table |
sonetFarEndPathIntervalNumber |
15 minute |
|
sonetFarEndPathIntervalESs |
15 minute | |
|
sonetFarEndPathIntervalSESs |
15 minute | |
|
sonetFarEndPathIntervalCVs |
15 minute | |
|
sonetFarEndPathIntervalUASs |
15 minute | |
|
sonetFarEndPathIntervalValidData |
15 minute | |
|
SonetVTCurrent Table |
sonetVTCurrentWidth |
Current |
|
sonetVTCurrentStatus |
Current | |
|
sonetVTCurrentESs |
Current | |
|
sonetVTCurrentSESs |
Current | |
|
sonetVTCurrentCVs |
Current | |
|
sonetVTCurrentUASs |
Current | |
|
SonetVTInterval Table |
sonetVTIntervalNumber |
15 minute |
|
sonetVTIntervalESs |
15 minute | |
|
sonetVTIntervalSESs |
15 minute | |
|
sonetVTIntervalCVs |
15 minute | |
|
sonetVTIntervalUASs |
15 minute | |
|
sonetVTIntervalValidData |
15 minute | |
|
SonetFarEndVTCurrent Table |
sonetFarEndVTCurrentESs |
Current |
|
sonetFarEndVTCurrentSESs |
Current | |
|
sonetFarEndVTCurrentCVs |
Current | |
|
sonetFarEndVTCurrentUASs |
Current | |
|
SonetFarEndVTInterval Table |
sonetFarEndVTIntervalNumber |
15 minute |
|
sonetFarEndVTIntervalESs |
15 minute | |
|
sonetFarEndVTIntervalSESs |
15 minute | |
|
sonetFarEndVTIntervalCVs |
15 minute | |
|
sonetFarEndVTIntervalUASs |
15 minute | |
|
sonetFarEndVTIntervalValidData |
15 minute |
Alcatel-Lucent 1665 DMX supports private SONET Day PM MIB Module. This module defines 24 hour SONET PM parameters for the SONET physical medium, section layer, line, path and tributary. This MIB module applies to individual SONET ports and tributaries.
|
Table |
Parameters |
|---|---|
|
dmxSonetSectionDay Table |
dmxSonetSectionDayNumber |
|
dmxSonetSectionDayESs | |
|
dmxSonetSectionDaySESs | |
|
dmxSonetSectionDaySEFSs | |
|
dmxSonetSectionDayCVs | |
|
dmxSonetSectionDayValidData | |
|
dmxSonetLineDay Table |
dmxSonetLineDayNumber |
|
dmxSonetLineDayESs | |
|
dmxSonetLineDaySESs | |
|
dmxSonetLineDayCVs | |
|
dmxSonetLineDayUASs | |
|
dmxSonetLineDayValidData | |
|
dmxSonetFarEndLineDay Table |
dmxSonetFarEndLineDayNumber |
|
dmxSonetFarEndLineDayESs | |
|
dmxSonetFarEndLineDaySESs | |
|
dmxSonetFarEndLineDayCVs | |
|
dmxSonetFarEndLineDayUASs | |
|
dmxSonetFarEndLineDayValidData | |
|
dmxSonetPathDay Table |
dmxSonetPathDayNumber |
|
dmxSonetPathDayESs | |
|
dmxSonetPathDaySESs | |
|
dmxSonetPathDayCVs | |
|
dmxSonetPathDayUASs | |
|
dmxSonetPathDayValidData | |
|
dmxSonetFarEndPathDay Table |
dmxSonetFarEndPathDayNumber |
|
dmxSonetFarEndPathDayESs | |
|
dmxSonetFarEndPathDaySESs | |
|
dmxSonetFarEndPathDayCVs | |
|
dmxSonetFarEndPathDayUASs | |
|
dmxSonetFarEndPathDayValidData | |
|
dmxSonetVTDay Table |
dmxSonetVTDayNumber |
|
dmxSonetVTDayESs | |
|
dmxSonetVTDaySESs | |
|
dmxSonetVTDayCVs | |
|
dmxSonetVTDayUASs | |
|
dmxSonetVTDayValidData | |
|
dmxSonetFarEndVTDay Table |
dmxSonetFarEndVTDayNumber |
|
dmxSonetFarEndVTDayESs | |
|
dmxSonetFarEndVTDaySESs | |
|
dmxSonetFarEndVTDayCVs | |
|
dmxSonetFarEndVTDayUASs | |
|
dmxSonetFarEndVTDayValidData |
In addition to standard SNMP traps, Alcatel-Lucent 1665 DMX supports the following five traps for all NE alarms: Alarms (dmxAlarm), Alarm Clears (dmxAlarmCL), Standing Conditions (dmxStandingCond), Standing Condition Clears (dmxStandingCondCL), and Transient Conditions (dmxTransientCond).
The following table shows the Standard DS1/E1 PM MIB tables and parameters defined in IETF RFC2495. This MIB module applies to individual DS1/E1 ports.
|
Table |
Parameters |
Description |
|---|---|---|
|
Dsx1CurrentEntry Table |
dsx1CurrentIndex |
Current |
|
dsx1CurrentESs |
Current | |
|
dsx1CurrentSESs |
Current | |
|
dsx1CurrentSEFSs |
Current | |
|
dsx1CurrentUASs |
Current | |
|
dsx1CurrentCSSs |
Current | |
|
dsx1CurrentPCVs |
Current | |
|
dsx1CurrentLESs |
Current | |
|
dsx1CurrentBESs |
Current | |
|
dsx1CurrentDMs |
Current | |
|
dsx1CurrentLCVs |
Current | |
|
Dsx1ConfigEntry Table |
dsx1LineIndex |
ifIndex |
|
dsx1TimeElapsed |
seconds since the beginning of current period | |
|
dsx1ValidIntervals |
number of previous 15-min intervals for which data was collected (usually 32) | |
|
dsx1LineType |
type of DS1/E1 line, e.g., E1 unframed | |
|
dsx1LineCoding |
line coding, e.g. B8ZS | |
|
dsx1SendCode |
code being sent | |
|
dsx1CircuitIdentifier |
circuit ID: 0,...,255 | |
|
dsx1LoopbackConfig |
loopback configuration | |
|
dsx1LineStatus |
bit mapped line status information | |
|
dsx1SignalMode |
signaling mode | |
|
dsx1TransmitClockSource |
loop timing, local timing or through timing | |
|
dsx1Fdl |
facilities data link capabilities | |
|
dsx1InvalidIntervals |
number of intervals for which no data is available (usually 0) | |
|
dsx1LineLength |
length of the DS1/E1 line in meters | |
|
dsx1LineStatusLastChange |
time this DS1/E1 entered its current line status state | |
|
dsx1LineStatusChangeTrapEnable |
indicates whether dsx1LineStatusChange traps should be generated for this DS1/E1 | |
|
dsx1LoopbackStatus |
current state of the loopback on the DS1/E1 interface | |
|
dsx1Ds1ChannelNumber |
0...28 | |
|
dsx1Channelization |
DS1/E1 channelization: disabled, enabled DS0 or enabled DS1 | |
|
Dsx1IntervalEntry Table |
dsx1IntervalIndex |
15 minute |
|
dsx1IntervalNumber |
15 minute | |
|
dsx1IntervalESs |
15 minute | |
|
dsx1IntervalSESs |
15 minute | |
|
dsx1IntervalSEFSs |
15 minute | |
|
dsx1IntervalUASs |
15 minute | |
|
dsx1IntervalCSSs |
15 minute | |
|
dsx1IntervalPCVs |
15 minute | |
|
dsx1IntervalLESs |
15 minute | |
|
dsx1IntervalBESs |
15 minute | |
|
dsx1IntervalDMs |
15 minute | |
|
dsx1IntervalLCVs |
15 minute | |
|
dsx1IntervalValidData |
15 minute | |
|
Dsx1TotalEntry Table |
dsx1TotalIndex |
24 hour |
|
dsx1TotalESs |
24 hour | |
|
dsx1TotalSESs |
24 hour | |
|
dsx1TotalSEFSs |
24 hour | |
|
dsx1TotalUASs |
24 hour | |
|
dsx1TotalCSSs |
24 hour | |
|
dsx1TotalPCVs |
24 hour | |
|
dsx1TotalLESs |
24 hour | |
|
dsx1TotalBESs |
24 hour | |
|
dsx1TotalDMs |
24 hour | |
|
dsx1TotalLCVs |
24 hour | |
|
Dsx1ChanMappingEntry Table |
dsx1ChanMappedIfIndex |
DS1/E1 channel number ifIndex |
|
Dsx1FarEndCurrentEntry Table |
dsx1FarEndCurrentIndex |
Current |
|
dsx1FarEndTimeElapsed |
Current | |
|
dsx1FarEndValidIntervals |
Current | |
|
dsx1FarEndCurrentESs |
Current | |
|
dsx1FarEndCurrentSESs |
Current | |
|
dsx1FarEndCurrentSEFSs |
Current | |
|
dsx1FarEndCurrentUASs |
Current | |
|
dsx1FarEndCurrentCSSs |
Current | |
|
dsx1FarEndCurrentLESs |
Current | |
|
dsx1FarEndCurrentPCVs |
Current | |
|
dsx1FarEndCurrentBESs |
Current | |
|
dsx1FarEndCurrentDMs |
Current | |
|
dsx1FarEndInvalidIntervals |
Current | |
|
Dsx1FarEndIntervalEntry Table |
dsx1FarEndIntervalIndex |
15 minute |
|
dsx1FarEndIntervalNumber |
15 minute | |
|
dsx1FarEndIntervalESs |
15 minute | |
|
dsx1FarEndIntervalSESs |
15 minute | |
|
dsx1FarEndIntervalSEFSs |
15 minute | |
|
dsx1FarEndIntervalUASs |
15 minute | |
|
dsx1FarEndIntervalCSSs |
15 minute | |
|
dsx1FarEndIntervalLESs |
15 minute | |
|
dsx1FarEndIntervalPCVs |
15 minute | |
|
dsx1FarEndIntervalBESs |
15 minute | |
|
dsx1FarEndIntervalDMs |
15 minute | |
|
dsx1FarEndIntervalValidData |
15 minute | |
|
Dsx1FarEndTotalEntry Table |
dsx1FarEndTotalIndex |
24 hour |
|
dsx1FarEndTotalESs |
24 hour | |
|
dsx1FarEndTotalSESs |
24 hour | |
|
dsx1FarEndTotalSEFSs |
24 hour | |
|
dsx1FarEndTotalUASs |
24 hour | |
|
dsx1FarEndTotalCSSs |
24 hour | |
|
dsx1FarEndTotalLESs |
24 hour | |
|
dsx1FarEndTotalPCVs |
24 hour | |
|
dsx1FarEndTotalBESs |
24 hour | |
|
dsx1FarEndTotalDMs |
24 hour |
Alcatel-Lucent 1665 DMX supports the following DS1 trap.
|
Table |
Parameters |
|---|---|
|
ds1Traps |
dsx1LineStatusChange |
The following table shows the Standard DS3/EC-1 PM MIB tables and parameters defined in IETF RFC2496. This MIB module applies to individual DS3/EC-1 ports.
|
Table |
Parameters |
Description |
|---|---|---|
|
Dsx3ConfigEntry |
dsx3LineIndex |
ifIndex |
|
dsx3TimeElapsed |
seconds since the beginning of current period | |
|
dsx3ValidIntervals |
number of previous 15-min intervals for which data was collected (usually 32) | |
|
dsx3LineType |
type of DS3/E3 line | |
|
dsx3LineCoding |
line coding, e.g. B3ZS | |
|
dsx3SendCode |
code being sent | |
|
dsx3CircuitIdentifier |
N/A - always “0” | |
|
dsx3LoopbackConfig |
loopback configuration | |
|
dsx3LineStatus |
bit mapped line status information | |
|
dsx3TransmitClockSource |
loop timing, local timing or through timing | |
|
dsx3InvalidIntervals |
number of intervals for which no data is available (usually 0) | |
|
dsx3LineLength |
length of the DS3/E3 line in meters | |
|
dsx3LineStatusLastChange |
time this DS3/E3 entered its current line status state | |
|
dsx3LineStatusChangeTrap Enable |
indicates whether dsx3LineStatusChange traps should be generated for this DS3/E3 - read only | |
|
dsx3LoopbackStatus |
current state of the loopback on the DS3/E3 interface | |
|
dsx3Channelization |
“enabled DS1” if CP is TMUX, otherwise “disabled” | |
|
dsx3Ds1ForRemoteLoop |
not supported, always “0” | |
|
Dsx3CurrentEntry |
dsx3CurrentIndex |
Current |
|
dsx3CurrentPESs |
Current - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3CurrentPSESs |
Current - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3CurrentSEFSs |
Current | |
|
dsx3CurrentUASs |
Current | |
|
dsx3CurrentLCVs |
Current | |
|
dsx3CurrentPCVs |
Current - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3CurrentLESs |
Current | |
|
dsx3CurrentCCVs |
Current - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3CurrentCESs |
Current - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3CurrentCSESs |
Current - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
Dsx3IntervalEntry |
dsx3IntervalIndex |
Current |
|
dsx3IntervalNumber |
15 minute | |
|
dsx3IntervalPESs |
15 minute - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3IntervalPSESs |
15 minute - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3IntervalSEFSs |
15 minute | |
|
dsx3IntervalUASs |
15 minute | |
|
dsx3IntervalLCVs |
15 minute | |
|
dsx3IntervalPCVs |
15 minute - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3IntervalLESs |
15 minute | |
|
dsx3IntervalCCVs |
15 minute - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3IntervalCESs |
15 minute - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3IntervalCSESs |
15 minute - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3IntervalValidData |
15 minute | |
|
Dsx3TotalEntry |
dsx3TotalIndex |
24 hour |
|
dsx3TotalPESs |
24 hour - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3TotalPSESs |
24 hour - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3TotalSEFSs |
24 hour | |
|
dsx3TotalUASs |
24 hour | |
|
dsx3TotalLCVs |
24 hour | |
|
dsx3TotalPCVs |
24 hour - valid only if ENT-rr:fmt=PBIT, otherwise “0” | |
|
dsx3TotalLESs |
24 hour | |
|
dsx3TotalCCVs |
24 hour - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3TotalCESs |
24 hour - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
dsx3TotalCSESs |
24 hour - valid only if ENT-rr:fmt=CPBIT, otherwise “0” | |
|
Dsx3FarEndConfigEntry |
dsx3FarEndLineIndex |
not supported |
|
dsx3FarEndEquipCode |
not supported | |
|
dsx3FarEndLocationIDCode |
not supported | |
|
dsx3FarEndFrameIDCode |
not supported | |
|
dsx3FarEndUnitCode |
not supported | |
|
dsx3FarEndFacilityIDCode |
not supported |
Alcatel-Lucent 1665 DMX supports the following DS3 trap.
|
Table |
Parameter |
|---|---|
|
DS3 Traps |
dsx3LineStatusChange |
Alcatel-Lucent 1665 DMX supports private DS3/EC-1 PM MIB Module. This MIB module applies to individual DS3/EC-1 ports and tributaries.
|
Table |
Parameters |
Description |
|---|---|---|
|
DmxDmxDsx3CurrentEntry |
dmxDsx3CurrentIndex |
Current |
|
dmxDsx3CurrentFMESs |
Current - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dmxDsx3CurrentFMSESs |
Current - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dmxDsx3CurrentFMCVs |
Current - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
DmxDmxDsx3IntervalEntry |
dmxDsx3IntervalIndex |
Interval |
|
dmxDsx3IntervalFMESs |
Interval - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dmxDsx3IntervalFMSESs |
Interval - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dmxDsx3IntervalFMCVs |
Interval - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dsx3DMXIntervalValidData |
||
|
DmxDmxDsx3TotalEntry |
dmxDsx3TotalIndex |
Total |
|
dmxDsx3TotalFMESs |
Total - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dmxDsx3TotalFMSESs |
Total - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
dmxDsx3TotalFMCVs |
Total - valid only if ENT-rr:fmt=FMBIT, otherwise “0” | |
|
DmxDsx3FarEndCurrentEntry |
dmxDsx3FarEndCurrentIndex |
Current |
|
dmxDsx3FarEndTimeElapsed |
Current | |
|
dmxDsx3FarEndValidIntervals |
Current | |
|
dmxDsx3FarEndCurrentCFMESs |
Current - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndCurrentCFMSESs |
Current - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndCurrentCFMCVs |
Current - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndCurrentUASs |
Current - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndInvalidIntervals |
Current | |
|
DmxDsx3FarEndIntervalEntry |
dmxDsx3FarEndIntervalIndex |
15 minute |
|
dmxDsx3FarEndIntervalNumber |
15 minute | |
|
dmxDsx3FarEndIntervalCFMESs |
15 minute - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndIntervalCFMSESs |
15 minute - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndIntervalCFMCVs |
15 minute - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndIntervalUASs |
15 minute - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndIntervalValidData |
15 minute | |
|
DmxDsx3FarEndTotalEntry |
dmxDsx3FarEndTotalIndex |
24 hour |
|
dmxDsx3FarEndTotalCFMESs |
24 hour - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndTotalCFMSESs |
24 hour - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndTotalCFMCVs |
24 hour - far end PM based on C-bit, F-bit and M-bit errors | |
|
dmxDsx3FarEndTotalUASs |
24 hour - far end PM based on C-bit, F-bit and M-bit errors |
Alcatel-Lucent 1665 DMX supports a private Fibre Channel/ESCON/FICON PM MIB module for retrieving Fibre Channel/ESCON/FICON PM parameters. This private MIB module applies to individual ports for the LNW73 circuit pack.
The following table shows the private Ethernet PM MIB module QOS parameters.
|
Table |
Object |
Parameter |
Definition |
|---|---|---|---|
|
dmxPortStatCountCurrentTable |
dmxPortStatCountCurrentRxElements |
The number of octets or bytes that have been received by this port (EINB). 1 |
|
|
dmxPortStatCountCurrentRxObjects |
The number of frames/packets that have been received by this port (EINF) 2 |
||
|
dmxPortStatCountCurrentInvalidCRC |
Count of frames received with invalid CRC (EDFE) |
||
|
dmxPortStatCountCurrentInvalidTxWords |
Count of invalid transmission words received at this port (INTXWD) |
||
|
dmxPortStatCountCurrentLossofSignal |
Count of instances of signal loss detected at port (LOS) |
||
|
dmxPortStatCountCurrentLossofSynchronization |
Count of instances of synchronization (LSYNC) |
||
|
dmxPortStatCountCurrentEncodingDisparityErrors |
Count of disparity errors received at this port (DSPERR) |
||
|
dmxPortStatCountCurrentTxElements |
The number of octets or bytes that have been transmitted by this port (EONB) 1 |
||
|
dmxPortStatCountCurrentTxObjects |
The number of frames/packets/ IOs/etc. that have been transmitted by this port (EONF) 2 |
||
|
dmxPortStatCountCurrentRxOverflowFramesDropped |
Count of received overflow frames dropped (RFOVD) |
||
|
dmxPortStatCountCurrentTxOverflowFramesDropped |
Count of transmit overflow frames dropped (TFOVD) |
||
|
dmxPortStatCountCurrentTxFramesCRCErrors |
Count of transmitted frames with CRC errors (TFCRC) |
||
|
dmxPortStatCountCur- rentTx10BERRErrors |
Count of transmitted 10B_ERR errors (T10BERR) |
||
|
dmxPortStatCountIntervalTable |
dmxPortStatCountIntervalIndex |
15 minute bucket index |
1 to 32 |
|
dmxPortStatCountIntervalRxElements |
The number of octets or bytes that have been received by this port (EINB) 1 |
15 minute | |
|
dmxPortStatCountIntervalRxObjects |
The number of frames/packets that have been received by this port (EINF) 2 |
15 minute | |
|
dmxPortStatCountIntervalInvalidCRC |
Count of frames received with invalid CRC (EDFE) |
15 minute | |
|
dmxPortStatCountIntervalInvalidTxWords |
Count of invalid transmission words received at this port (INTXWD) |
15 minute | |
|
dmxPortStatCountIntervalLossofSignal |
Count of instances of signal loss detected at port (LOS) |
15 minute | |
|
dmxPortStatCountIntervalLossofSynchronization |
Count of instances of synchronization (LSYNC) |
15 minute | |
|
dmxPortStatCountIntervalEncodingDisparityErrors |
Count of disparity errors received at this port (DSPERR) |
15 minute | |
|
dmxPortStatCountIntervalTxElements |
The number of octets or bytes that have been transmitted by this port (EONB) 1 |
15 minute | |
|
dmxPortStatCountIntervalTxObjects |
The number of frames/packets/ IOs/etc that have been transmitted by this port (EONF) 2 |
15 minute | |
|
dmxPortStatCountIntervalRxOverflowFramesDropped |
Count of received overflow frames dropped (RFOVD) |
||
|
dmxPortStatCountIntervalTxOverflowFramesDropped |
Count of transmit overflow frames dropped (TFOVD) |
||
|
dmxPortStatCountIntervalTxFramesCRCErrors |
Count of transmitted frames with CRC errors (TFCRC) |
||
|
dmxPortStatCountInter- valTx10BERRErrors |
Count of transmitted 10B_ERR errors (T10BERR) |
||
|
dmxPortStatCountDayTable |
dmxPortStatCountDayIndex |
day index |
current or previous 24 hour period |
|
dmxPortStatCountDayRxElements |
The number of octets or bytes that have been received by this port (EINB) 1 |
24 hour | |
|
dmxPortStatCountDayRxObjects |
The number of frames/packets that have been received by this port (EINF) 2 |
24 hour | |
|
dmxPortStatCountDayInvalidCRC |
Count of frames received with invalid CRC (EDFE) |
24 hour | |
|
dmxPortStatCountDayInvalidTxWords |
Count of invalid transmission words received at this port (INTXWD) |
24 hour | |
|
dmxPortStatCountDayLossofSignal |
Count of instances of signal loss detected at port (LOS) |
24 hour | |
|
dmxPortStatCountDayLossofSynchronization |
Count of instances of synchronization (LSYNC) |
24 hour | |
|
dmxPortStatCountDayEncodingDisparityErrors |
Count of disparity errors received at this port (DSPERR) |
24 hour | |
|
dmxPortStatCountDayTxElements |
The number of octets or bytes that have been transmitted by this port. (EONB) 1 |
24 hour | |
|
dmxPortStatCountDayTxObjects |
The number of frames/packets/ IOs/etc that have been transmitted by this port. (EONF) 2 |
24 hour | |
|
dmxPortStatCountDayRxOverflowFramesDropped |
Count of received overflow frames dropped (RFOVD) |
24 hour | |
|
dmxPortStatCountDayTxOverflowFramesDropped |
Count of transmit overflow frames dropped (TFOVD) |
24 hour | |
|
dmxPortStatCountDayTxFramesCRCErrors |
Count of transmitted frames with CRC errors (TFCRC) |
24 hour | |
|
dmxPortStatCountDay Tx10BERRErrors |
Count of transmitted 10B_ERR errors (T10BERR) |
24 hour | |
|
dmxVcgStatCountCurrentTable |
dmxVcgStatCountCurrentRxObjects |
The number of frames/packets that have been received by this port |
|
|
dmxVcgStatCountCurrentInvalidCRC |
Count of frames received with invalid CRC (EDFE) |
||
|
dmxVcgStatCountCurrentTxObjects |
The number of frames/packets that have been transmitted by this port |
||
|
dmxVcgStatCountCurrentRxSingleBitErrCorrectedGFP |
Count of received single-bit error corrected GFP header count (RCORH) |
||
|
dmxVcgStatCountCurrentRxMultiBitUncorrectedGFP |
Count of received uncorrected multi-bit error GFP header count (RCRCH) |
||
|
dmxVcgStatCountCurrentRxSingleBitErrCorrectedGFPSuperblk |
Count of received single-bit error corrected GFP super-block count (RCORF) |
||
|
dmxVcgStatCountIntervalTable |
dmxVcgStatCountIntervalIndex |
15 minute bucket index |
15 minute |
|
dmxVcgStatCountIntervalRxObjects |
The number of frames/packets that have been received by this port |
15 minute | |
|
dmxVcgStatCountIntervalInvalidCRC |
Count of frames received with invalid CRC (EDFE) |
15 minute | |
|
dmxVcgStatCountIntervalTxObjects |
The number of frames/packets that have been transmitted by this port |
15 minute | |
|
dmxVcgStatCountIntervalRxSingleBitErrCorrectedGFP |
Count of received single-bit error corrected GFP header count (RCORH) |
15 minute | |
|
dmxVcgStatCountIntervalRxMultiBitUncorrectedGFP |
Count of received uncorrected multi-bit error GFP header count (RCRCH) |
15 minute | |
|
dmxVcgStatCountIntervalRxSingleBitErrCorrectedGFPSuperblk |
Count of received single-bit error corrected GFP super-block count (RCORF) |
15 minute | |
|
dmxVcgStatCountDayTable |
dmxVcgStatCountDayIndex |
day index |
24 hour |
|
dmxVcgStatCountDayRxObjects |
The number of frames/packets that have been received by this port |
24 hour | |
|
dmxVcgStatCountDayInvalidCRC |
Count of frames received with invalid CRC (EDFE) |
24 hour | |
|
dmxVcgStatCountDayTxObjects |
The number of frames/packets that have been transmitted by this port |
24 hour | |
|
dmxVcgStatCountDayRxSingleBitErrCorrectedGFP |
Count of received single-bit error corrected GFP header count (RCORH) |
24 hour | |
|
dmxVcgStatCountDayRxMultiBitUncorrectedGFP |
Count of received uncorrected multi-bit error GFP header count (RCRCH) |
24 hour | |
|
dmxVcgStatCountDayRxSingleBitErrCorrectedGFPSuperblk |
Count of received single-bit error corrected GFP super-block count (RCORF) |
24 hour |
The following table shows the private Ethernet PM MIB module traps. These traps are only supported on the LNW73 pack.
|
dmxAlarmId |
Parameter |
|---|---|
|
dmxPortStatInc1GfcLos |
Loss of signal (LOS) on 1GFC port |
|
dmxPortStatInc1GfcLosClr |
LOS clear on 1GFC port |
|
dmxPortStatInc2GfcLos |
Loss of signal (LOS) on 2GFC port |
|
dmxPortStatInc2GfcLosClr |
LOS clear on ESCON port |
|
dmxPortStatIncEsconLos |
Loss of signal (LOS) on 2GFC port |
|
dmxPortStatIncEsconLosClr |
LOS clear on ESCON port |
|
dmxPortStatIncFiconLos |
Loss of signal (LOS) on FICON port |
|
dmxPortStatIncFiconLosClr |
LOS clear on FICON port |
|
dmxPortStatInc1GfcLsync |
inc. Loss of Synch (LSYNC) on 1GFC port |
|
dmxPortStatInc1GfcLsyncClr |
LSYNC clear on 1GFC port |
|
dmxPortStatInc2GfcLsync |
inc. Loss of Synch (LSYNC) on 2GFC port |
|
dmxPortStatInc2GfcLsyncClr |
LSYNC clear on ESCON port |
|
dmxPortStatIncEsconLsync |
inc. Loss of Synch (LSYNC) on 2GFC port |
|
dmxPortStatIncEsconLsyncClr |
LSYNC clear on ESCON port |
|
dmxPortStatIncFiconLsync |
inc. Loss of Synch (LSYNC) on FICON port |
|
dmxPortStatIncFiconLsyncClr |
LSYNC clear on FICON port |
|
dmxPortStatCount1GfcTINTXWD |
Invalid transmission words TCA received at this 1GFC port |
|
dmxPortStatCount2GfcTINTXWD |
Invalid transmission words TCA received at this 2GFC port |
|
dmxPortStatCountFiconTINTXWD |
Invalid transmission words TCA received at this FICON port |
|
dmxPortStatCountEsconTINTXWD |
Invalid transmission words TCA received at this ESCON port |
Alcatel-Lucent 1665 DMX supports the standard Ethernet interface MIB module defined in RFC2863. This module defines Ethernet traps and retrievable Ethernet port and PM parameters. This MIB module applies to individual Fast Ethernet and Gigabit Ethernet ports.
The following table shows the standard Ethernet interface MIB module parameters.
|
Object |
Definition |
|---|---|
|
ifIndex |
Interface Index |
|
ifDescr |
Interface description (mfg, product, version) |
|
ifType |
Type of interface |
|
ifMtu |
Interface maximum rate (bps) - for GbE circuit pack, this is “1,000,000,000”, for FE circuit pack, value is based on value of the line rate parameter. If the line rate is 10M, ifSpeed value is “10,000,000”. If the line rate parameter is 100M, ifSpeed value is “100,000,000”. |
|
ifPhysAddress |
MAC Address |
|
ifAdminStatus |
Administration status (up, down or testing) (read only). Value is always “up”. |
|
ifOperStatus |
Operational status (up, down, testing, unknown, dormant, notPresent or lowerLayerDown). If board/port is removed, value is “notPresent”. If there is an existing alarm on the port, i.e., Loss of signal (LOS) or Auto-Negotiation Mismatch (ANM) on the port, then the value is “down”, else the value is “up”. |
|
ifLastChange |
TimeTicks since last re-initialization |
|
ifInOctets |
Total Bytes Received |
|
IfInUcastPkts |
Frames Received: Broadcast Frames Received - Multicast Frames Received |
|
ifInMulticastPkts |
Multicast Frames Received |
|
ifInBroadcastPkts |
Broadcast Frames Received |
|
ifInDiscards |
Dropped Frames |
|
ifInErrors |
CRC Error + Oversize Frames + Fragments + Jabber + MAC Rx Error |
|
ifInUnknownProtos |
(always 0) |
|
ifOutOctets |
Bytes Sent |
|
IfOutUcastPkts |
Frames Sent - Out Multicast Frames - Out Broadcast Frames |
|
ifOutMulticastPkts |
Out Multicast Frames |
|
ifOutBroadcastPkts |
Out Broadcast Frames |
|
IfOutDiscards |
(always 0) (not supported in this release) |
|
ifOutErrors |
(always 0) (not supported in this release) |
|
ifName |
Interface name - (always set to NULL) |
|
ifHCInOctets |
Total Bytes Received |
|
ifHCInUcastPkts |
Frames Received: Broadcast Frames Received - Multicast Frames Received |
|
ifHCInMulticastPkts |
Multicast Frames Received |
|
ifHCInBroadcastPkts |
Broadcast Frames Received |
|
ifHCOutOctets |
Bytes Sent |
|
ifHCOutUcastPkts |
Frames Sent - Out Multicast Frames - Out Broadcast Frames |
|
ifHCOutMulticastPkts |
Out Multicast Frames |
|
ifHCOutBroadcastPkts |
Out Broadcast Frames |
|
ifLinkUpDownTrapEnable |
Traps enabled or disabled - Alcatel-Lucent 1665 DMX, Metropolis® DMXpress, and Alcatel-Lucent 1665 DMXtend support READ-ONLY |
|
ifHighSpeed |
Interface speed (Mbps) - for GbE circuit pack, this is “1,000”, for FE circuit pack, value is based on line rate parameter. If the line rate is 10M, ifSpeed value is “10”. If the line rate is 100M, ifSpeed value is “100”. |
|
ifPromiscuousMode |
Promiscuous mode (true or false) - Alcatel-Lucent 1665 DMX, Metropolis® DMXpress and Alcatel-Lucent 1665 DMXtend support READ-ONLY |
|
ifConnectorPresent |
Physical connector present (true or false) |
|
ifAlias |
Interface alias name - READ-ONLY - (always set to NULL) |
|
ifCounterDiscontinuity TimeTimeStamp |
Time of last counter discontinuity |
The following table shows the standard Ethernet interface MIB module traps.
|
Object |
Definition |
|---|---|
|
linkUp |
link up |
|
linkDown |
link down |
Alcatel-Lucent 1665 DMX supports the standard Ethernet PM MIB module defined in RFC2358 and RFC2665. This module defines additional retrievable Ethernet PM parameters. This MIB module applies to individual Fast Ethernet and Gigabit Ethernet ports.
The following table shows the standard Ethernet PM MIB module parameters.
|
Object |
Definition |
|---|---|
|
ifIndex |
Interface Index |
|
dot3StatsAlignmentErrors |
Fragments |
|
dot3StatsFCSErrors |
CRC Error |
|
dot3StatsSingleCollisionFrames |
Collision |
|
dot3StatsMultipleCollisionFrames |
(always 0) (not supported in this release) |
|
dot3StatsSQETestErrors |
(always 0) (not supported in this release) |
|
dot3StatsDeferredTransmissions |
(always 0) (not supported in this release) |
|
dot3StatsLateCollisions |
Late Collision |
|
dot3StatsExcessiveCollisions |
(always 0) (not supported in this release) |
|
dot3StatsInternalMacTransmitErrors |
(always 0) (not supported in this release) |
|
dot3StatsCarrierSenseErrors |
(always 0) (not supported in this release) |
|
dot3StatsFrameTooLongs |
Oversize Frames |
|
dot3StatsInternalMacReceiveErrors |
MAC Rx Error |
|
dot3StatsSymbolErrors |
(always 0) (not supported in this release) |
|
dot3StatsDuplexStatus |
Duplex Status (half duplex (2), full duplex (3) - added by RFC2665 |
|
dot3ControlFunctionsSupported |
pause (0) --802.3 flow control - added by RFC2665 |
|
dot3ControlInUnknownOpcodes |
(always 0) - added by RFC2665 (not supported in this release) |
|
dot3PauseAdminMode |
Flow control default mode (read only) - added by RFC2665 |
|
dot3PauseOperMode |
Flow control operational mode (disabled [1], enabled transmit & receive [4]) - added by RFC2665 |
|
dot3InPauseFrames |
(always 0) - added by RFC2665 (not supported in this release) |
|
dot3OutPauseFrames |
(always 0) - added by RFC2665 (not supported in this release) |
Alcatel-Lucent 1665 DMX supports a private Ethernet PM MIB module for Ethernet traps and for retrieving Ethernet PM parameters. This private Ethernet PM MIB module applies to individual Fast Ethernet and Gigabit Ethernet ports.
The following table shows the private Ethernet PM MIB module parameters.
|
Object |
Parameter |
Definition |
|---|---|---|
|
dmxEthPmonTypeCurrent |
port type |
FE or GbE port |
|
dmxEthPmonCurrentEinb |
Incoming number of bytes (EINB) |
Total Bytes Received |
|
dmxEthPmonCurrentEinf |
Incoming number of frames (EINF) |
Frames Received or Total Frames Received |
|
dmxEthPmonCurrentEdfc |
Dropped frames: congestion (EDFC) |
Dropped Frames |
|
dmxEthPmonCurrentEdfe |
Dropped frames: errors (EDFE) |
CRC Error + Oversize Frames + Fragments + Jabber + MAC Rx Error 2 |
|
dmxEthPmonCurrentEonb |
Outgoing number of bytes (EONB) |
Bytes Sent |
|
dmxEthPmonCurrentEonf |
Outgoing number of frames (EONF) |
Frames Sent |
|
dmxEthPmonIntervalIndex |
15 minute bucket index |
1 to 32 |
|
dmxEthPmonTypeInterval |
port type |
FE or GbE port |
|
dmxEthPmonIntervalEinb |
Incoming number of bytes (EINB) |
Total Bytes Received: 15 minute |
|
dmxEthPmonIntervalEinf |
Incoming number of frames (EINF) |
Frames Received or Total Frames Received: 15 minute |
|
dmxEthPmonIntervalEdfc |
Dropped frames: congestion (EDFC) |
Dropped Frames: 15 minute |
|
dmxEthPmonIntervalEdfe |
Dropped frames: errors (EDFE) |
CRC Error + Oversize Frames + Fragments + Jabber + MAC Rx Error: 15 minute 2 |
|
dmxEthPmonIntervalEonb |
Outgoing number of bytes (EONB) |
Bytes Sent: 15 minute |
|
dmxEthPmonIntervalEonf |
Outgoing number of frames (EONF) |
Frames Sent: 15 minute |
|
dmxEthPmonDayType |
port type |
FE or GbE port |
|
dmxEthPmonDayEinb |
Incoming number of bytes (EINB) |
Total Bytes Received: 24 hour |
|
dmxEthPmonDayEinf |
Incoming number of frames (EINF) |
Frames Received or Total Frames Received: 24 hour |
|
dmxEthPmonDayEdfc |
Dropped frames: congestion (EDFC) |
Dropped Frames: 24 hour |
|
dmxEthPmonDayEdfe |
Dropped frames: errors (EDFE) |
CRC Error + Oversize Frames + Fragments + Jabber + MAC Rx Error: 24 hour 2 |
|
dmxEthPmonDayEonb |
Outgoing number of bytes (EONB) |
Bytes Sent: 24 hour |
|
dmxEthPmonDayEonf |
Outgoing number of frames (EONF) |
Frames Sent: 24 hour |
|
dmxEthPmonCurrentEdfb |
dropped frames - broadcast rate limit (EDFB) |
LNW170 only |
|
dmxEthPmonCurrentEdfcg |
dropped green frames - congestion (EDFCG) |
LNW170 only |
|
dmxEthPmonCurrentEdfcy |
dropped yellow frames - congestion (EDFCY) |
LNW170 only |
|
dmxEthPmonCurrentEindp |
dropped PAUSE frames (EINDP) |
LNW170 only |
|
dmxEthPmonCurrentEincp |
number of frames trapped to CPU (EINCP) |
LNW170 only |
|
dmxEthPmonCurrentEinfb |
incoming number of broadcast frames (EINFB) |
LNW170 only |
|
dmxEthPmonCurrentEinfm |
incoming number of multicast frames (EINFM) |
LNW170 only |
|
dmxEthPmonCurrentEinfu |
incoming number of unicast frames (EINFU) |
LNW170 only |
|
dmxEthPmonCurrentEocp |
number of frames received from CPU (EOCP) |
LNW170 only |
|
dmxEthPmonCurrentEonfb |
outgoing number of broadcast frames (EONFB) |
LNW170 only |
|
dmxEthPmonCurrentEonfm |
outgoing number of multicast frames (EONFM) |
LNW170 only |
|
dmxEthPmonCurrentEonfu |
outgoing number of unicast frames (EONFU) |
LNW170 only |
|
dmxEthPmonCurrentStprole |
Number of times the STP port role changed (STPROLE) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentStpstate |
Number of times the STP port state changed, except to or from DISA (STPSTATE) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentStproot |
Number of times the bridge changed to or from being root. The value is reported only on the lowest numbered port (a VCG if present, else a LAN if present, else a LAG) in a spanning tree group. All other ports in the group report 0 (STPROOT) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentBpdut |
Number of occurrences of BPDU timeout (BPDUT) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentBpdui |
Incoming number of BPDU frames (BPDUI) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentBpduo |
Outgoing number of BPDU frames (BPDUO) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentBpdud |
Number of BPDU frames dropped (BPDUD) |
LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonCurrentRplblk |
Number of times the RPL block state changed (RPLBLK) |
LNW170 only (VCG and LAN ports) |
|
dmxEthPmonCurrent Erp1blk |
Number of times the ERP port #1 block state changed (ERP1BLK) |
LNW170 only (VCG and LAN ports) |
|
dmxEthPmonCurrent Erp2blk |
Number of times the ERP port #2 block state changed (ERP2BLK) |
LNW170 only (VCG and LAN ports) |
|
dmxEthPmonCurrentRapsr |
Number of transmitted R-APS PDUs (RAPSR) |
LNW170 only (VCG and LAN ports) |
|
dmxEthPmonCurrentRapst |
Number of transmitted R-APS PDUs (RAPST) |
LNW170 only (VCG and LAN ports) |
|
dmxEthPmonCurrentEdfems |
Number of Ethernet Dropped Frames due to Exceeding MTU SIze (EDFEMS) |
LNW170 only (VCG and LAN ports) LNW64, LNW74. and LNW87 (LAN ports) |
|
dmxEthPmonIntervalEdfb |
dropped frames - broadcast rate limit (EDFB) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEdfcg |
dropped green frames - congestion (EDFCG) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEdfcy |
dropped yellow frames - congestion (EDFCY) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEindp |
dropped PAUSE frames (EINDP) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEincp |
number of frames trapped to CPU (EINCP) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEinfb |
incoming number of broadcast frames (EINFB) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEinfm |
incoming number of multicast frames (EINFM) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEinfu |
incoming number of unicast frames (EINFU) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEocp |
number of frames received from CPU (EOCP) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEonfb |
outgoing number of broadcast frames (EONFB) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEonfm |
outgoing number of multicast frames (EONFM) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalEonfu |
outgoing number of unicast frames (EONFU) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalStprole |
Number of times the STP port role changed (STPROLE) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalStpstate |
Number of times the STP port state changed, except to or from DISA (STPSTATE) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalStproot |
Number of times the bridge changed to or from being root. The value is reported only on the lowest numbered port (a VCG if present, else a LAN if present, else a LAG) in a spanning tree group. All other ports in the group report 0 (STPROOT) |
15 minute - LNW170 only |
|
dmxEthPmonIntervalBpdut |
Number of occurrences of BPDU timeout (BPDUT) |
15 minute LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonIntervalBpdui |
Incoming number of BPDU frames (BPDUI) |
15 minute LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonIntervalBpduo |
Outgoing number of BPDU frames (BPDUO) dmxEthPmonIntervalBpdut |
15 minute LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonIntervalBpdud |
Number of BPDU frames dropped (BPDUD) |
15 minute LNW170 only (VCG and LAN ports or LAGs) |
|
dmxEthPmonIntervalValid Data |
Interval valid data |
Used to flag counter discontinuities when protection switching between protected packs |
|
dmxEthPmonIntervalRplblk |
Number of times the RPL block state changed (RPLBLK) |
15 minute LNW170 only (VCG and LAN ports) |
|
dmxEthPmonInterval Erp1blk |
Number of times the ERP port #1 block state changed (ERP1BLK) |
15 minute LNW170 only (VCG and LAN ports) |
|
dmxEthPmonInterval Erp2blk |
Number of times the ERP port #2 block state changed (ERP2BLK) |
15 minute LNW170 only (VCG and LAN ports) |
|
dmxEthPmonDayEdfb |
dropped frames - broadcast rate limit (EDFB) |
24 hour - LNW170 only |
|
dmxEthPmonDayEdfcg |
dropped green frames - congestion (EDFCG) |
24 hour - LNW170 only |
|
dmxEthPmonDayEdfcy |
dropped yellow frames - congestion (EDFCY) |
24 hour - LNW170 only |
|
dmxEthPmonDayEindp |
dropped PAUSE frames (EINDP) |
24 hour - LNW170 only |
|
dmxEthPmonDayEincp |
number of frames trapped to CPU (EINCP) |
24 hour - LNW170 only |
|
dmxEthPmonDayEinfb |
incoming number of broadcast frames (EINFB) |
24 hour - LNW170 only |
|
dmxEthPmonDayEinfm |
incoming number of multicast frames (EINFM) |
24 hour - LNW170 only |
|
dmxEthPmonDayEinfu |
incoming number of unicast frames (EINFU) |
24 hour - LNW170 only |
|
dmxEthPmonDayEocp |
number of frames received from CPU (EOCP) |
24 hour - LNW170 only |
|
dmxEthPmonDayEonfb |
outgoing number of broadcast frames (EONFB) |
24 hour - LNW170 only |
|
dmxEthPmonDayEonfm |
outgoing number of multicast frames (EONFM) |
24 hour - LNW170 only |
|
dmxEthPmonDayEonfu |
outgoing number of unicast frames (EONFU) |
24 hour - LNW170 only |
|
dmxEthPmonDayStprole |
Number of times the STP port role changed (STPROLE) |
24 hour - LNW170 only |
|
dmxEthPmonDayStpstate |
Number of times the STP port state changed, except to or from DISA (STPSTATE) |
24 hour - LNW170 only |
|
dmxEthPmonDayStproot |
Number of times the bridge changed to or from being root. The value is reported only on the lowest numbered port (a VCG if present, else a LAN if present, else a LAG) in a spanning tree group. All other ports in the group report 0 (STPROOT) |
24 hour - LNW170 only |
|
dmxEthPmonDayBpdut |
Number of occurrences of BPDU timeout (BPDUT) |
24 hour - LNW170 only |
|
dmxEthPmonDayBpdui |
Incoming number of BPDU frames (BPDUI) |
24 hour - LNW170 only |
|
dmxEthPmonDayBpduo |
Outgoing number of BPDU frames (BPDUO) |
24 hour - LNW170 only |
|
dmxEthPmonDayBpdud |
Number of BPDU frames dropped (BPDUD) |
24 hour - LNW170 only |
The definition of Dropped Frames is based on the counters supported by the Galnet devices. The definition of this parameter for the Private Line board, which doesn’t have the Galnet devices, may differ.
Oversize Frames are not included for LNW170 (LAN and VCG ports) or LNW64, LNW87, LNW74 (LAN ports).
The following table shows the private Ethernet PM MIB module traps.
|
Trap Object |
Definition |
|---|---|
|
dmxIncFeLanLos |
Loss of signal (LOS) on FE LAN port |
|
dmxIncFeLanLosClr |
LOS clear on FE LAN port |
|
dmxIncFeLanAnm |
Auto-Negotiation Mismatch (ANM) on FE LAN port |
|
dmxIncFeLanAnmClr |
ANM clear on FE LAN port |
|
dmxIncGeLanLos |
Loss of signal (LOS) on GbE LAN port |
|
dmxIncGeLanLosClr |
LOS clear on GbE LAN port |
|
dmxIncGeLanAnm |
Auto-Negotiation Mismatch (ANM) on GbE LAN port |
|
dmxIncGeLanAnmClr |
ANM clear on GbE LAN port |
|
dmxIncGeLanECV |
Excessive Code Violation on GbE LAN port |
|
dmxIncGeLanECVClr |
Excessive Code Violation clear on GbE LAN port |
|
dmxIncGeLanTEDFC |
Dropped frames due to congestion TCA on GbE LAN port |
|
dmxIncFeLanTEDFC |
Dropped frames due to congestion TCA on FE LAN port |
|
dmxIncGeLanTEDFE |
Dropped frames due to errors TCA on GbE LAN port |
|
dmxIncFeLanTEDFE |
Dropped frames due to errors TCA on FE LAN port |
Alcatel-Lucent 1665 DMX supports private Ethernet PM MIB module for retrieving QOS parameters. This private Ethernet PM MIB module applies to individual Fast Ethernet and Gigabit Ethernet ports for the LNW170 pack.
The following table shows the private Ethernet PM MIB module QOS parameters.
|
Object |
Parameter |
Definition |
|---|---|---|
|
dmxEthPmonQosCurrentTagid |
VLANid in the range 1–4093 except for PORT and COSPORT mode which has a value of “NA” |
|
|
dmxEthPmonQosCurrentCos |
Class of Service in the range 0–3 |
|
|
dmxEthPmonQosCurrentQibg |
Incoming bytes marked green (QIB–G) |
|
|
dmxEthPmonQosCurrentQipg |
Incoming packets marked green (QIP–G) |
|
|
dmxEthPmonQosCurrentQiby |
Incoming bytes marked yellow (QIB-Y) |
|
|
dmxEthPmonQosCurrentQipy |
Incoming packets marked yellow (QIP-Y) |
|
|
dmxEthPmonQosCurrentQibr |
Incoming bytes marked red (dropped) (QIB-R) |
|
|
dmxEthPmonQosCurrentQipr |
Incoming packets marked red (dropped) (QIP-R ) |
|
|
dmxEthPmonQosIntervalIndex |
15 minute bucket index |
1 to 32 |
|
dmxEthPmonQosIntervalTagid |
VLANid in the range 1–4093 except for PORT and COSPORT modewhich has a value of “NA” |
15 minute |
|
dmxEthPmonQosIntervalCos |
Class of Service in the range 0–3 |
15 minute |
|
dmxEthPmonQosIntervalQibg |
Incoming bytes marked green (QIB–G) |
15 minute |
|
dmxEthPmonQosIntervalQipg |
Incoming packets marked green (QIP–G) |
15 minute |
|
dmxEthPmonQosIntervalQiby |
Incoming bytes marked yellow (QIB-Y) |
15 minute |
|
dmxEthPmonQosIntervalQipy |
Incoming packets marked yellow (QIP-Y) |
15 minute |
|
dmxEthPmonQosIntervalQibr |
Incoming bytes marked red (dropped) (QIB-R) |
15 minute |
|
dmxEthPmonQosIntervalQipr |
Incoming packets marked red (dropped) (QIP-R ) |
15 minute |
|
dmxEthPmonQosDayIndex |
day index |
current or previous 24 hour period |
|
dmxEthPmonQosDayTagid |
VLANid in the range 1–4093 except for PORT and COSPORT modewhich has a value of “NA” |
24 hour |
|
dmxEthPmonQosDayCos |
Class of Service in the range 0–3 |
24 hour |
|
dmxEthPmonQosDayQibg |
Incoming bytes marked green (QIB–G) |
24 hour |
|
dmxEthPmonQosDayQipg |
Incoming packets marked green (QIP–G) |
24 hour |
|
dmxEthPmonQosDayQiby |
Incoming bytes marked yellow (QIB-Y) |
24 hour |
|
dmxEthPmonQosDayQipy |
Incoming packets marked yellow (QIP-Y) |
24 hour |
|
dmxEthPmonQosDayQibr |
Incoming bytes marked red (dropped) (QIB-R) |
24 hour |
|
dmxEthPmonQosDayQipr |
Incoming packets marked red (dropped) (QIP-R ) |
24 hour |
Alcatel-Lucent 1665 DMX supports a private VCG MIB module for VCG traps. This private VCG MIB module applies to individual VCGs.
The following table shows the private VCG MIB module traps.
|
Trap Object |
Definition |
|---|---|
|
dmxIncVcgFail |
Incoming VCG fail |
|
dmxIncVcgFailClr |
Incoming VCG fail clear |
|
dmxIncVcgGeLanTEDFC |
Dropped frames due to congestion TCA on VCG GbE WAN port |
|
dmxIncVcgFeLanTEDFC |
Dropped frames due to congestion TCA on VCG FE WAN port |
|
dmxIncVcgGeLanTEDFE |
Dropped frames due to errors TCA on VCG GbE WAN port |
|
dmxIncVcgFeLanTEDFE |
Dropped frames due to errors TCA on VCG FE WAN port |
|
dmxIncVcgGfpRcfFail |
General framing procedure remote client signal failed (GFP_RCF) |
|
dmxIncVcgGfpRcfFailClr |
General framing procedure remote client signal failed (GFP_RCF) clear |
|
dmxIncVcgLopcFail |
VCG loss of partial capacity (VCGLOPC) |
|
dmxIncVcgLopcFailClr |
VCG loss of partial capacity (VCGLOPC) clear |
|
dmxIncVcgFoprFail |
VCG failure of LCAS protocol (Sink) (VCGFOPR) |
|
dmxIncVcgFoprFailClr |
VCG failure of LCAS protocol (Sink) (VCGFOPR) clear |
|
dmxIncVcgFoptFail |
VCG failure of LCAS protocol (Source) (VCGFOPT) |
|
dmxIncVcgFoptFailClr |
VCG failure of LCAS protocol (Source) (VCGFOPT) clear |
|
dmxIncVcgNOTLCAS |
Far End Not LCAS (NOTLCAS) |
|
dmxIncVcgNOTLCASClr |
Far End Not LCAS clear (NOTLCAS) |
|
dmxIncSts1Lom |
Incoming STS1 loss of multiframe |
|
dmxIncSts1LomClr |
Incoming STS1 loss of multiframe clear |
|
dmxIncSts3cLom |
Incoming STS3C loss of multiframe |
|
dmxIncSts3cLomClr |
Incoming STS3C loss of multiframe clear |
|
dmxIncVt1Lom |
Incoming VT1 loss of multiframe |
|
dmxIncVt1LomClr |
Incoming VT1 loss of multiframe clear |
|
dmxIncSts1Sqm |
Incoming STS1 sequence number mismatch |
|
dmxIncSts1SqmClr |
Incoming STS1 sequence number mismatch |
|
dmxIncSts3cSqm |
Incoming STS3C sequence number mismatch |
|
dmxIncSts3cSqmClr |
Incoming STS3C sequence number mismatch |
|
dmxIncVt1Sqm |
Incoming Vt1 sequence number mismatch |
|
dmxIncVt1SqmClr |
Incoming Vt1 sequence number mismatch |
|
dmxIncVcgSts1MSUL |
STS1 Member Signal Unacceptable -LCAS (MSU-L) |
|
dmxIncVcgSts1MSULClr |
STS1 Member Signal Unacceptable -LCAS (MSU-L) Clear |
|
dmxIncVcgSts3cMSUL |
STS3c Member Signal Unacceptable -LCAS (MSU-L) |
|
dmxIncVcgSts3cMSULClr |
STS3c Member Signal Unacceptable -LCAS (MSU-L) Clear |
|
dmxIncVcgVtMSUL |
VT1.5 Member Signal Unacceptable -LCAS (MSU-L) |
|
dmxIncVcgVtMSULClr |
VT1.5 Member Signal Unacceptable -LCAS (MSU-L) Clear |
Alcatel-Lucent 1665 DMX supports a private MIB module for retrieving equipment information parameters and equipment traps. This private MIB module applies to individual circuit packs.
The following table shows the private MIB module parameters.
|
Object |
Definition |
|---|---|
|
dmxCardType |
Circuit pack type. |
|
dmxCardAPP |
Circuit pack apparatus code |
|
dmxCardSSN |
Circuit pack series number |
|
dmxCardCLEI |
Common Language Equipment code |
|
dmxCardECI |
Equipment Catalog Item code |
|
dmxCardSLN |
Circuit pack serial number |
|
dmxSftwVersion |
Version of the software currently stored in the circuit pack |
|
dmxCardVlanTagMode |
Virtual LAN tagging mode. This parameter is ONLY reported for slots containing an Ethernet circuit pack. Values: 802.1TAG (IEEE 802.1Q mode), TRANS (Transparent mode), NOTAG (No Tag mode) |
|
dmxCardVtVcat |
VT Virtual Concatenation. This parameter specifies the number of STS-1s dedicated to VT virtual concatenation. |
|
dmxCardDataType |
Data type. Values are: FC-FICON - in this mode, data ports are configured individually for Fibre Channel or FICON. ESCON - in this mode all ports on the circuit pack are set for ESCON This object applies only to the LNW73 circuit pack |
The following table shows the private MIB module traps.
|
Object |
Definition |
|---|---|
|
dmxCpNotAllowed |
Circuit pack not allowed |
|
dmxCpNotAllowedClr |
Circuit pack not allowed clear |
|
dmxFACTERM |
Illegal circuit pack type |
|
dmxFACTERMClr |
Illegal circuit pack type clear |
|
dmxFETERM |
FE-LAN circuit pack failed |
|
dmxFETERMClr |
FE-LAN circuit pack failed clear |
|
dmxGETERM |
GE-LAN circuit pack failed |
|
dmxGETERMClr |
GE-LAN circuit pack failed clear |
|
dmxCpRemoved |
Circuit pack removed |
|
dmxCpRemovedClr |
Circuit pack removed clear |
|
dmxCpInserted |
Circuit pack inserted |
| November 2011 | Copyright © 2011 Alcatel-Lucent. All rights reserved. |