Using the work instructions, determine the DS3/EC-1 port to be discontinued.

At the terminating nodes, click the Alarm List button to obtain an NE Alarm List and verify that no alarms are present. Clear all alarms before continuing this procedure.

Reference:

Alcatel-Lucent 1665 Data Multiplexer (DMX) Alarm Messages and Trouble Clearing Guide, 365-372-302

Important!

This step may activate the office alarms. The audible alarm may be suppressed by pressing the ACO push-button.

At the cross-connect panel or equivalent connection point at the terminating nodes, remove the DS3/EC-1 signal associated with the port being discontinued.

Result:

The FAULT LED flashes on the circuit pack with signals removed.

At the terminating nodes, click the Alarm List button to obtain an NE Alarm List and verify that the correct DS3/EC-1 signal was removed.

At the terminating nodes, select Configuration →Update System → Update States to clear the DS3/EC-1 LOS alarms.

Result:

The flashing FAULT LEDs go off.

At the terminating nodes, click the Alarm List button to obtain an NE Alarm List and verify that the DS3/EC-1 LOS alarm is cleared.

At the terminating nodes, select View → Equipment to access the required DS3/EC-1 ports and verify that the Port Monitoring Mode changed to AUTO.

Determine the cross-connections for the circuit being discontinued using the work instructions, or at the terminating nodes and non-terminating nodes (UPSRs/BLSRs only), select View → Cross-Connections to obtain a current list of cross-connections.

Record the source addresses (SRC) of the cross-connections to be deleted.

At the terminating nodes, select Configuration → Cross-Connections to access the Cross-Connection Wizard and delete the add/drop cross-connections for all DS3/EC-1 service being removed.

(Refer to the cross-connection source addresses recorded in Step 8.)

Important!

DS3/EC-1 slots cannot be unequipped without an alarm until all port cross-connections are removed.

If required, at each pass-through node (UPSRs/BLSRs only) select Configuration → Cross-Connections to access the Cross-Connection Wizard and delete the pass-through cross-connections for all DS3/EC-1 service being removed.

(Refer to the cross-connection source addresses recorded in Step 8.)

Important!

The LNW16 circuit packs have 12 DS3/EC-1 ports. The LNW19/19B circuit packs have 48 DS3/EC-1 ports.

If all the DS3/EC-1 ports on the circuit pack are being discontinued, you may remove the circuit pack, if required.

If circuit packs have been removed continue with Step 13, otherwise proceed to Step 14.

If circuit packs have been removed, update the Alcatel-Lucent 1665 DMX internal equipment list.

From the System View menu select Configuration → Update System → Update Inventory.

Click OK.

Insert 177D application blanks or LNW98 Detectable Blank circuit packs into empty slots, then proceed to Step 15.

If circuit packs have not been removed, provision the Port Monitoring Mode of the DS3/EC-1 ports to AUTO, NMON, or IS as required.

From the System View menu select Configuration → Equipment, expand the required circuit pack details, then select the DS3/EC-1 port.

Under the Fault Management section, select NMON (Not Monitored), AUTO (Automatic), or IS (In Service) for the Port Monitoring Mode .

Important!

If the Port Monitoring Mode is NMON, the port is not monitored/alarmed, and the port will not automatically transition to the in service state if a valid signal is detected. If the Port Monitoring Mode is AUTO, the port automatically transitions to the in service state if a valid signal is detected and the port is monitored/alarmed. If the Port Monitoring Mode is provisioned to IS, the port is monitored and alarms are reported.

At the terminating nodes and non-terminating nodes (UPSRs/BLSRs only), click the Alarm List button to obtain an NE Alarm List and verify that no alarms are present.

End of steps