Provision Ethernet circuit pack parameters

Procedure 11-10: Provision Ethernet circuit pack parameters

Overview

This procedure provides a list of provisionable parameters for Ethernet circuit packs.

Privilege level

You must login as either a Privileged or General user to complete this procedure.

Before you begin

Prior to performing this procedure, refer to Before you begin and Required equipment in this chapter and you must have complete work instructions for this procedure that detail:

The network configuration and the terminating Ethernet nodes.
The values to be set for each parameter.

Steps

Use this procedure as a reference for provisioning Ethernet circuit pack parameters.

Use the ed-eqpt TL1 command or select Configuration → Equipment from the System View menu. Select the Ethernet circuit pack being provisioned, then click Select.

Use Table 11-3, ED-EQPT command provisionable parametersas reference to provision the necessary parameters from your work instructions.

End of steps

ED-EQPT command parameters

Table 11-3, ED-EQPT command provisionable parameters lists the provisionable parameters for the Ethernet circuit packs:

Table 11-3: ED-EQPT command provisionable parameters

Parameter	Description
type	Equipment TypeWhen addressed to a slot AID, the legal value is ETHPK (Ethernet circuit pack). Other values are valid when the slot is not equipped with an Ethernet pack.
brst	Burst Size (1-255): Burst size determines the length or size of the burst that will be allowed by the peak information rate (PIR) policer. The valid range is 1 to 255. The default is 5. A larger value of burst size means that larger bursts will be allowed; a smaller value of burst size means that the PIR is more strictly enforced and less burstiness is allowed. This parameter affects policing for all VLANs (in 802.1Q mode) or all port tags (in transparent mode). This parameter applies to the LNW66, LNW67, and LNW68 Ethernet circuit packs.
cint	Credit Interval (1-4095): Credit interval for adding tokens to the token buckets used by the peak information rate (PIR) policer. The valid range is 1 to 4095. The default is 125, which corresponds to an interval of approximately 65.5 ms. The minimum value of 1 corresponds to an interval of 524.288 us. The maximum value of 4095 corresponds to 2.15 sec. This parameter affects policing for all VLANs (in 802.1Q mode) or all port tags (in transparent mode). This parameter applies to the LNW66, LNW67, and LNW68 Ethernet circuit packs.
eccmode	Ethernet Cross Connect Mode STS1 - STS-1 Cross-Connect mode supports only STS-1 cross-connections. For the LNW71, STS1 mode supports up to two STS-1 cross-connections to each VCG (1-24). For the LNW70/LNW170, STS1 mode supports up to 48 STS-1 cross-connections to VCG 1-2, 32 STS-1 cross-connections to VCG 3-28, and 10 STS-1 cross-connections to VCG 29-32. For the LNW78, STS1 mode supports up to 24 STS-1 cross-connections to VCG 1-2. STS3c - STS-3c Cross-Connect mode supports at most one STS-3c or one STS-1 cross-connection to each of the first 16 VCGs (1-16), (VCGs 17-24 are not used). Applies only to the LNW71 circuit pack. STS12c - STS-12c Cross-Connect mode supports STS-3c, STS12c,or virtual concatenated STS3c cross-connections to each VCG. Applies to the LNW70/LNW170 and LNW78 circuit packs. This parameter applies to the LNW70/LNW170, LNW71, and LNW78 circuit packs.
enetmd	Ethernet Port Configuration. This parameter allows the Ethernet ports to operate with different PTMs. This parameter is valid when type = ETHPK. This parameter does not apply to the LNW87. See lnrate (Line Rate) in ed-eport. Values are: GX_FX (initial value). For the LNW70/LNW170, sets ports 1-4 to operate with optical GbE PTMs. Sets ports 5-8 to operate with optical FE PTMs. For the LNW78, sets ports 1-2 to operate with optical GbE PTMs. Sets ports 5-8 to operate with optical FE PTMs. GT_FX For the LNW70/LNW170, sets ports 1-4 to operate with electrical GbE PTMs. Sets ports 5-8 to operate with optical FE PTMs. For the LNW78, sets ports 1-2 to operate with electrical GbE PTMs. Sets ports 5-8 to operate with optical FE PTMs. FT_FX For the LNW70/LNW170, sets ports 1-4 to operate with electrical FE PTMs. Sets ports 5-8 to operate with optical FE PTMs. For the LNW74, enables electrical FE backplane ports 1-16 and sets ports 17-24 to operate with optical FE PTMs. Provisionable for the LNW74 only when the main slots are equipped with VLF OLIU circuit packs. FX For the LNW74, disables electrical FE backplane ports 1-16 and sets ports 17-24 to operate with optical FE PTMs. Provisionable for the LNW74 only when the main slots are equipped with VLF OLIU circuit packs. GX_FT For the LNW70/LNW170, sets ports 1-4 to operate with optical GbEs PTMs. Sets ports 5-8 to operate with electrical FE PTMs. For the LNW78, sets ports 1-2 to operate with optical GbEs PTMs. Sets ports 5-8 to operate with electrical FE PTMs. GT_FT For the LNW70/LNW170, sets ports 1-4 to operate with electrical GbEs PTMs. Sets ports 5-8 to operate with electrical FE PTMs. For the LNW78, sets ports 1-2 to operate with electrical GbEs PTMs. Sets ports 5-8 to operate with electrical FE PTMs. FT For the LNW70/LNW170, sets ports 1-8 to operate with electrical FE PTMs.
enetmd (continued)	GX (initial value) For the LNW63 sets ports 1-4 to operate with optical GbE PTMs. For the LNW64 sets ports 1-8 to operate with optical GbE PTMs. GT For the LNW63 sets ports 1-4 to operate with electrical GbE PTMs. For the LNW64 sets ports 1-8 to operate with electrical GbE PTMs. GT_GX For the LNW64, sets ports 1-4 to operate with electrical GbE PTMs. Sets ports 5-8 to operate with optical GbE PTMs. This parameter does not apply to the LNW87.
fefi_code	Far End Fault Indication Code is a 2 digit hexadecimal number in the range 03 to FE. The initial value is 05. (If a single digit is entered, it is padded with a zero to the left. For example, 5 is interpreted as 05). feﬁ_code is applicable only for LNW74, LNW70/170, and LNW87 circuit packs and is speciﬁed on a circuit pack basis.
mst	Socket Maintenance State. This parameter applies to equipped sockets only. Values are: Normal - While in the normal state, any subsequent removal of the pluggable transmission module is reported with the assigned ASAP alarm severity level. Maint - While in the maintenance state, any subsequent removal of the pluggable transmission module is reported with an alarm severity level of a standing condition regardless of the assigned ASAP alarm severity level.
prot_state	Slot Protection state. This parameter speciﬁes the protection state for the companion circuit packs in a slot pair. Values are: PROT - protected. UNPROT - unprotected. This parameter applies only to LNW170 Ethernet circuit packs. When a slot pair is equipped with LNW170 circuit packs, provisioning the slot prot_state to PROT sets the packs to be equipment protected and assigns certain corresponding ports on the companion circuit packs to the same ﬁxed link aggregation groups: LAG1 (slot 1, port 1 and slot 2, port 1); LAG2 (slot 1, port 2 and slot 2, port 2); LAG3 (slot 1, port 5 and slot 2, port 5); LAG4 (slot 1, port 6 and slot 2, port 6). When prot_state is provisioned to UNPROT, if the NE is equipped with VLF MAINs, the LNW170 circuit packs are unprotected and the corresponding ports on the companion packs operate independently. If the NE is equipped with non-VLF MAINs, the LNW170 in the slot addressed by the ED-EQPT command is unprotected and any circuit pack in the companion slot is alarmed.
taudit	Transmission audit. Enables or disables the LNW70/LNW170 transmission audit. The transmission audit is a consistency check between counters on various hardware devices on the LNW70/LNW170 circuit pack. A transmission audit failure will result in a LAN or VCG segment audit failed alarm or equipment NP audit failed alarm. Values are: ENABLED - Enables the transmission audit function. This is the initial value. DISABLED - Disables the transmission audit function. This parameter applies only to LNW70/LNW170 Ethernet circuit packs. When taudit is provisioned for a protected LNW170 circuit pack, the provisioned value will apply to both circuit packs of the protected pair.
vlantagmd	Vlan Tagging Mode. 802.1TAG - IEEE 802.1Q mode. Default value for FE circuit packs. Allows VLAN ID assignments to LAN and VCG ports for customer identification. Applies to the LNW66, LNW67, and LNW68 circuit packs only. TRANS - Transparent mode. Allows Port Tag provisioning independent of customer VLANs. Applies to the LNW66, LNW67, and LNW68 circuit packs only. NOTAG - No VLAN or port tag assignments. Accepts all customer packets. Default value for the LNW70/LNW170 and LNW78 circuit packs. Only mode of operation for the LNW63, LNW64, LNW71, LNW87 and LNW74 circuit packs. SWITCHED - In this mode, switched Ethernet ports are allowed on the Ethernet circuit pack. The vlantagmd (TRANS or 802.1TAG) is selectable per virtual switch (ent-vrtsw), not on the circuit pack. Applies to the LNW70/LNW170 and LNW78 circuit packs. Only mode of operation for the LNW78 circuit pack.
vt_vcat	VT Virtual Concatenation: Determines the number of STS-1s dedicated to VT virtual concatenation. A value of `0` indicates that VT virtual concatenation is disabled. A value of `12` indicates that 12 STS-1s (336 VT1.5s) are reserved for VT virtual concatenation. Up to 63 VT1.5s may be assigned to any VCG. Applies to the LNW74 circuit pack only.