OAM-PM Service Site Summary report

Overview

An OAM-PM Service Site Summary report can be run by itself or as a drill-down from an OAM-PM Service Summary or OAM-PM Composite Service Summary report. The report shows the aggregate view of the set of sessions on a selected service.

The report includes the following session types:

• ETH-CFM Session

• TWAMP-Light Session

The following service types are supported:

• Epipe

• VPLS

• VPRN

• MVPLS

Use cases

QoS analysis—Identify potential service impacting issues based on thresholds for latency, jitter, and packet loss between specific NEs.

Troubleshooting—Troubleshoot service performance by service and segment

Prerequisites

The following sessions need to be performed in the NFM-P for OAM-PM Service Site Summary reports to be created:

• A DMM session must be defined with accounting enabled.

• A TWAMP-Light session must be defined with accounting enabled.

• For session loss information to be available, an SLM session must also be defined.

Report inputs

The following table shows the report inputs.

Table 13-20: OAM-PM Service Site Summary report inputs

Prompt	Notes
Session Type	ETH-CFM Session, TWAMP-Light Session
End Date	Calendar date or relative date (for example, two days ago) and time
Granularity	Aggregation types: None (raw collection interval) Hourly Daily Monthly
Report range	Length of time to be reported, in hours, days, or months
Service Type	Search using partial names or full names. Select individual items or click Select All. Both the NE name and its IP address display.
Service Name/ID
Service Sites
Bin Type	Frame Delay—The Avg Delay, Min Delay, and Max Delay in the report output is the delay in microseconds Frame Delay Range—The Avg Delay, Min Delay, and Max Delay in the report output is the delay range in microseconds Inter Frame Delay Variation—The Avg Delay, Min Delay, and Max Delay in the report output is the delay variation (jitter) in microseconds
Result set limit	Number of results to report
Show report output on one page	Select the check box to enable pagination. Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.

Report characteristics

The following table lists the principal report characteristics.

Table 13-21: OAM-PM Service Site Summary report characteristics

Characteristic	Value
Data type	OAM session statistics
Source database	Auxiliary database
NE types supported	7210 SAS-M 24F, 7210 SAS-M 24F 2XFP, 7210 SAS-M 24F 2XFP ETR, 7210 SAS-T 12F 10T 4XFP, 7210 SAS-T 12F 10T 4XFP ETR, 7210 SAS-X 24F 2XFP, 7210 SAS-K, 7210 SAS-R6, 7210 SAS-R12, 7210 SAS-S/SX 1/10GE VC 7250 IXR-6, 7250 IXR-R6, 7250 IXR-s, 7250 IXR-10, 7250 IXR-e all 7450 ESS variants all 7750 SR variants all 7950 XRS variants
Drill-down support	Yes—Opens an OAM-PM Service Site report of the selected session type: a view of the results of tests on the site. From an OAM-PM Service Site report: Click on a delay result to show an OAM-PM Latency report. Click on a jitter or loss result to show an OAM-PM Loss report.

OAM-PM ETH-CFM Service Site Summary report overview

The OAM-PM ETH-CFM Service Site Summary report shows an aggregated view of PM CFM DMM and PM CFM SLM sessions for a specified service over a specified time period, grouped by source and target NE.

Example

The following figure shows a report example.

Figure 13-20: OAM-PM ETH-CFM Service Site Summary report

OAM-PM TWAMP-Light Service Site Summary report overview

The OAM-PM TWAMP-Light Service Site Summary report shows an aggregated view of TWAMP Light session statistics on a specified service over a specified time period, grouped by source and target NE.

Example

The following figures show a report example.

Figure 13-21: OAM-PM TWAMP-Light Service Site Summary report