Service Utilization per Port report

Service Utilization per Port report overview

The Service Utilization per Port report shows the utilization of individual services for a selected access port. It is used to identify what services are consuming the majority of the bandwidth on a particular port. This report can be launched on its own or as a drill-down of the Port Throughput Summary report.

The default display is a table showing average ingress and egress utilization. By default the table is sorted by average utilization in decreasing value order (worst first), regardless of ingress or egress direction.

For SR variants, 7705 SAR-Hm, and 7705 SAR-Hmc, the report supports QoS policies, virtual schedulers, queue overrides, policer overrides, and the egress aggregate rate limit.

For the 7210 SAS, the report supports QoS policies, queue/meter overrides, and the egress aggregate rate limit.

For the 7705 SAR, the report supports QoS policies and the egress aggregate rate limit.

The report supports the port limit and local limit, which are the CIR and PIR values configured as percentages.

It is not mandatory to configure QoS for this report since the default QoS settings apply.

Use cases

Capacity planning—Use the report to examine utilization patterns for planning future capacity requirements.

Fault impact analysis—If the port is down or suffering performance issues, use this report to quickly identify the impacted services.

The Rate (kbps) rate type, Percent Port, and Percent Local rate types are supported for this report.

Prerequisites

The following table describes the aggregation rules that must be enabled and the accounting policies that must be configured for the NEs on which statistics are to be collected; see the NSP NFM-P Statistics Management Guide for information about configuring an accounting policy. The accounting policy must be assigned to the SAPs that belong to services for which the Utilization reports will be created. For the report to be created as a drill-down from a Port Throughput Summary report, the Port Throughput prerequisites must also be in place; see Port Throughput Summary report. To view the report for granularities other than raw data, the aggregation rules must be enabled; see How do I configure analytics aggregation?.

Table 14-19: Service Utilization per Port report prerequisites

Aggregator name	Monitored object class	Statistics class	Statistics collection	Details	NE types
SAP Interface Stats Aggregator Egress	service.AccessInterface	service.CompleteServiceEgressPacketOctets	Accounting, file, and log policies	completeSvcInEg policy	7705 SAR 7705 SAR Hm 7750 SR Note: esat ports are not supported
SAP Interface Stats Aggregator Ingress	service.AccessInterface	service.CompleteServiceIngressPacketOctets	Accounting, file, and log policies	completeSvcInEg policy	7250 IXR-R6 7705 SAR 7705 SAR Hm 7750 SR
Service Egress Octets Aggregator	service.AccessInterface	service.ServiceEgressOctets	Accounting, file, and log policies	svcEgressOctet policy	7210 SAS-D 7210 SAS Dxp 7210 SAS-K 7210 SAS-M 7210 SAS-Mxp 7210 SAS-R 7210 SAS-S/Sx 7210 SAS-T 7210 SAS-X Note: 7210 SAS-E and 7210 SAS-S/Sx are not supported due to NE limitations.
Service Ingress Octets Aggregator	service.AccessInterface	service.ServiceIngressOctets	Accounting, file, and log policies	svcIngressOctet policy	7210 SAS-D 7210 SAS Dxp 7210 SAS-K 7210 SAS-M 7210 SAS-Mxp 7210 SAS-R 7210 SAS-S/Sx 7210 SAS-T 7210 SAS-X

Report characteristics

The following table lists the principal report characteristics.

Table 14-20: Service Utilization per Port report characteristics

Characteristic	Value
Data type	Statistics
Source database	Auxiliary database
Report inputs	Prompt	Notes
	End date	Calendar date or relative date (for example, two days ago) and time
	Granularity	Aggregation types: None (raw data) Hourly Daily Monthly
	Report range	Length of time to be reported, in hours or days
	NE Types	Search using partial names or wildcard (%). Select individual items or click Select All.
	NE Name (or NE Pattern)
	NEs
	Port Name (or Port Name Pattern)	Search using partial names or wildcard (%). Select individual items or click Select All.
	Port/ LAG
	Display Service Full Name	Select the check box to show the full names of the services in the table.
	Percentile	Identify a percentile of interest between 1 and 99.
	Logo Resource ID	The logo to add to the report. Enter the Resource ID of the logo image in the Images folder. The default is the Nokia logo. To create the report without a logo, leave the Logo Resource ID field blank.
	Logo Position	Choose Left, Middle, or Right. The logo appears on the left on the first page of the report if you choose Left or Middle.
	Show report output on one page	Select the check box to enable pagination. Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.
Drill-down support	Yes: Click on a Service Name to launch a Ping Service Summary report. Click on a Service ID to launch an OAM-PM Service Summary report. Click on an Egress Actual value to launch a SAP Throughput report. Click on an Egress Utilization value to launch a Service Utilization Details report. The drill-down from the Service Utilization per port report is only supported when the Service Utilization report is performed on a service that is supported by the target report: Ping Service Summary reports support EPIPE, CPIPE, VPLS, MVPLS, and VPRN OAM-PM Service Summary reports support EPIPE, VPLS, MVPLS, and VPRN

Example

The following figure shows a report example.