| |
|
1 |
Perform
How do I create a service template?.
|
2 |
From the Service Management, Services view, click + CREATE.
The Select a service template to start form opens displaying a list of service templates.
|
3 |
Click on a VPLS service template from the list.
The Create Service form opens with the Template Name parameter populated.
|
4 |
Configure the parameters, as required:
|
Parameter |
Description |
|
Service Name |
Specifies the name of the service. Must be unique from other services created using NSP. |
|
Customer ID |
Specifies the customer ID |
|
Description |
Describes the service |
|
Admin State |
Specifies the initial administrative state of the service upon deployment |
|
Job ID |
Specifies the work-order number |
|
VPLS Type |
Specifies the virtual circuit type |
|
Management VPLS |
Specifies whether or not the service will be used for management |
|
MTU |
Specifies the MTU of the service |
|
NE Service ID |
Specifies the NE service ID |
|
5 |
In the Site Details panel, click + ADD.
The Add Site form opens.
|
6 |
Configure the parameters, as required:
|
Parameter |
Description |
|
Device ID |
Specifies the device identifier |
|
Site Name |
Specifies the site name |
|
Description |
Describes the site |
|
MTU |
Specifies the MTU of the site |
|
Routed VPLS |
Specifies whether or not the VPLS will be routed |
|
STP |
|
Admin State |
Specifies the STP administrative state |
|
Mode |
Specifies the protocol version |
|
Priority |
Specifies the STP bridge priority |
|
Mac Flush |
|
Propagate |
Specifies whether or not to propagate MAC flush messages received from the T-LDP |
|
Send On Failure |
Specifies whether or not to send MAC withdraw message on SAP/Spoke-SDP failure |
|
Fdb |
|
Discard Unknown |
Specifies whether or not to discard packets with unknown destination MAC addresses |
|
High Watermark |
Specifies the high watermark for the FDB table |
|
Low Watermark |
Specifies the low watermark for the FDB table |
|
Size |
Specifies the maximum MAC entries in the FDB |
|
Learning |
Specifies whether or not to enable learning of new MAC addresses |
|
Aging |
Specifies whether or not to enable aging of MAC addresses |
|
Local Age Time |
Specifies the aging time for locally learned MAC addresses |
|
Remote Age Time |
Specifies the aging time for remotely learned MAC addresses |
|
Split Horizon Group (click +ADD) |
|
Name |
The name of the split horizon group to which the SDP belongs |
|
Description |
Description of the split horizon group to which the SDP belongs |
|
7 |
Perform one of the following:
-
If the VPLS Type parameter was set to B-VPLS in
Step 4, use the Source B-MAC parameter in the PBB panel to specify the base source B-MAC address for the B-VPLS service.
-
If the VPLS Type parameter was set to I-VPLS in
Step 4, configure the parameters, as required:
|
Parameter |
Description |
|
Backbone VPLS Service Name |
Specifies the name of the service. Must be unique from other services created using NSP. |
|
ISID |
Specifies the ISID of the service |
|
8 |
In the SAP details panel, click + ADD.
The Add SAP form opens.
|
9 |
Configure the parameters, as required:
|
Parameter |
Description |
|
Port ID |
Specifies the port identifier |
|
Inner VLAN Tag |
Specifies the inner VLAN tag |
|
Outer VLAN Tag |
Specifies the outer VLAN tag |
|
Admin State |
Specifies the administrative state of the service |
|
Description |
Describes the SAP |
|
Collect Accounting Statistics |
Specifies whether or not accounting statistics will be collected |
|
Multi Service Site |
Specifies the multi service site name |
|
10 |
Perform the following to specify an accounting policy to be used:
-
Click on the Accounting Policy field. The Select Accounting Policy form opens.
-
Click on an accounting policy in the list, then click SELECT. The Select Accounting Policy form closes.
|
11 |
Configure the parameters in the Cpu Protection Panel, as required:
|
Parameter |
Description |
|
Policy Id |
Specifies the CPM protection policy |
|
Enable QoS |
Specifies whether or not QoS is enabled |
|
Enable IP/IPv6 Filter |
Specifies whether or not an IP/IPv6 filter is enabled |
|
Split Horizon Group (if neither QoS nor IP/IPv6 Filter are enabled) |
Name of the split horizon group to which the SDP belongs |
|
12 |
If QoS was enabled in
Step 11, configure the parameters as required in both the ingress and egress panels:
|
Parameter |
Description |
|
QoS |
|
Match QinQ Dot1p (ingress only) |
Specifies the match QinQ Dot1p |
|
QinQ Mark Top Only (egress only) |
Specifies whether top Q-tags are marked |
|
SAP Ingress |
|
Policy Name |
Specifies the name of the ingress SAP policy |
|
Queuing Type |
Specifies the ingress queuing type |
|
SAP Egress |
|
Policy Name |
Specifies the name of the egress SAP policy |
|
Queue (click + ADD) |
|
Queue ID |
Specifies the unique identifier for the queue |
|
CBS |
Specifies the CBS of the queue |
|
MBS |
Specifies the MBS of the queue |
|
PIR (kbps) |
Specifies the PIR rate of the queue |
|
CIR (kbps) |
Specifies the CIR rate of the queue |
|
Policer (click + ADD) |
|
Policer ID |
Specifies the unique identifier for the policer |
|
CBS |
Specifies the CBS of the policer |
|
MBS |
Specifies the MBS of the policer |
|
Stat Mode |
Specifies the mode of statistics collected by the policer |
|
Policer Override Rate |
Specifies the policer override rate |
|
Policer Control Policy |
|
Policy Name |
Specifies the name of the policer control policy |
|
Overrides (click check box) |
|
Max rate |
Specifies the maximum rate |
|
Min Thresh Separation |
Specifies the minimum threshold separation |
|
Priority (click +ADD) |
|
Priority Level |
Specifies the priority level |
|
Mbs Contribution |
Specifies the minimum amount of cumulative buffer space allowed |
|
Scheduler Policy |
|
Policy Name |
Specifies the name of the scheduler policy |
|
Scheduler (click + ADD) |
|
Scheduler Name |
Specifies the name of the scheduler |
|
PIR |
Specifies the PIR rate of the scheduler |
|
CIR |
Specifies the CIR rate of the scheduler |
|
Weight |
Specifies the relative weight of the scheduler to feed the queue |
|
Cir Weight |
Specifies the weight used at the within-CIR port priority level |
|
Aggregate Policer (ingress only) |
|
Rate |
Specifies the enforced aggregate rate for all queues |
|
Burst |
Specifies the aggregate policer burst |
|
Cir |
Specifies the aggregate policer CIR |
|
Cbs |
Specifies the aggregate policer CBS |
|
Vlan Qos Policy (egress only) |
|
Policy Name |
Specifies the Egress VLAN QoS policy name |
|
Port Redirect |
Specifies whether or not to enable Egress VLAN QoS policy port redirect |
|
Egress Remark Policy (egress only) |
|
Policy Name |
Specifies the Egress Remark policy name |
|
Agg Rate or Percent Agg Rate |
Specifies the enforced aggregate rate for all queues |
|
13 |
If an IP/IPv6 filter was enabled in
Step 11, configure the parameters as required in both the ingress and egress panels:
|
Parameter |
Description |
|
Aggregate Policer (ingress only) |
|
Rate |
Specifies the enforced aggregate rate for all queues |
|
Burst |
Specifies the aggregate policer burst |
|
Cir |
Specifies the aggregate policer CIR |
|
Cbs |
Specifies the aggregate policer CBS |
|
IP/IPv6 Filter |
|
IP |
Specifies the IP filter identifier |
|
IPv6 |
Specifies the IPv6 filter identifier |
|
Split Horizon Group (egress only) |
Name of the split horizon group to which the SDP belongs |
|
14 |
Configure the parameters, as required:
|
Parameter |
Description |
|
Fdb |
|
Maximum Mac Addresses |
Specifies the maximum number of MAC entries in the FDB |
|
Discard Unknown Source |
Specifies whether or not to discard frames with unknown source |
|
Mac Pinning |
Specifies whether or not to enable MAC address pinning on this SAP |
|
Auto Learn Mac Protect |
Specifies whether or not to enable automatic update of MAC protect list |
|
Learning |
Specifies whether or not to enable learning of new MAC addresses |
|
Aging |
Specifies whether or not to enable aging of MAC addresses |
|
Anti Spoof |
Specifies the type of anti-spoof filtering to be used |
|
Oper Group |
Specifies the operational group |
|
Igmp Snooping |
|
Import Policy |
Specifies the import policy that filters IGMP packets |
|
Maximum Number Groups |
Specifies the maximum number of groups allowed |
|
Send Queries |
Specifies whether or not to generate IGMP general queries |
|
Policy |
Specifies the multicast CAC policy name |
|
Total |
Specifies the maximum allowed bandwidth |
|
Mandatory |
Specifies the pre-reserved bandwidth for all mandatory channels |
|
Group (click +ADD) |
|
Group Addresses |
Specifies the group address of static IGMP multicast channel |
|
Source or Starg |
Enables adding a list entry for source |
|
Starg |
Specifies any source address (*,G) |
|
Source (click +ADD) |
|
Source Address |
Specifies the source IP address of multicast channel sending data |
Click ADD to add the SAP.
The Add SAP form closes.
|
15 |
Perform one of the following:
-
If required, repeat
Step 8 to
Step 14 to add additional SAPs.
-
Continue to
Step 16.
|
16 |
Configure the parameters in the MEP panel, as required:
|
Parameter |
Description |
|
MD Admin Name |
Specifies the admin-assigned maintenance domain index value |
|
MA Admin Name |
Specifies the admin-assigned maintenance association index value |
|
MEP ID |
Specifies the MEP identifier |
|
MAC Address |
Specifies the MAC address of the MEP |
|
One Way Delay Threshold |
Specifies the time limit for one way delay tests |
|
CCM |
Specifies whether or not the MEP will generate CCM tests |
|
CCM LTM Priority |
Specifies the priority of CCM and LTM messages transmitted by the MEP |
|
Admin State |
Specifies the administrative state of the MEP |
Click ADD to add the site(s).
The Add Site form closes.
|
17 |
In the SDP Details panel, click + ADD.
The Add SDP form opens.
|
18 |
Configure the parameters, as required:
|
Parameter |
Description |
|
SDP Type |
Specifies the SDP type, mesh or spoke |
|
VC Type |
Specifies the virtual circuit type, ether or VLAN |
|
Admin State |
Specifies the desired state of the service SDP binding |
|
Source Device ID |
Specifies the SDP source device identifier |
|
Destination Device ID |
Specifies the SDP destination device identifier |
|
Steering Parameter |
Specifies the steering parameter used by NSP |
|
SDP ID |
Specifies the SDP identifier |
|
Description |
Describes the SDP binding |
|
Override VC-ID |
Specifies whether or not the VC-ID will serve as the NE service ID for the SDP |
|
VC ID |
Specifies the SDP virtual circuit identifier |
|
Fdb |
|
Maximum Mac Addresses |
Specifies the maximum number of MAC entries in the FDB |
|
Discard Unknown Source |
Specifies whether or not to discard packets with unknown destination MAC addresses |
|
Mac Pinning |
Specifies whether or not to enable MAC address pinning on this SAP |
|
Auto Learn Mac Protect |
Specifies whether or not to enable automatic update of MAC protect list |
|
Igmp Snooping |
|
Maximum Number Groups |
Specifies the maximum number of groups allowed |
|
Dhcp |
|
Snoop |
Specifies whether or not to allow DHCP snooping of DHCP messages on the SAP or SDP |
|
Force Vc Forwarding |
Specifies the VC forwarding action |
|
Control Ward |
Specifies whether or not to use the control word as preferred |
Click ADD to add the SDP binding.
The Add SDP form closes.
|
19 |
Perform one of the following:
-
Select the Reserve Resources check box and click PLAN to create the service in a Planned state.
-
Click SAVE to create the service in a Saved state.
-
Click DEPLOY to create the service in a Deployed state.
See
What is Life Cycle State? for more information.
End of steps |