LSP Throughput with Forecast report

LSP Throughput with Forecast report overview

The LSP Throughput with Forecast report provides the LSP throughput with forecasting data.

The report can generate a forecast depending on the granularity. For raw and hourly granularities, forecast periods and periods per season are ignored. To generate a forecast, you must provide at least two seasons of data, although more may be required if the input data is not linear. For example, if you choose a seasonality value of 7 and the granularity is daily, you must use a report range of at least 14 days.

When the forecast algorithm fails, a pop-up message displays with the recommendation that you either lower the seasonality value or increase the report range.

The aggregation time zone and the session time zone must be same.

You may consider scheduling the report, as it takes several minutes to generate.

Limitations

Minimum and maximum throughput aggregation cannot be compared with the minimum and maximum throughput values generated from raw granularity.

Prerequisites

The session time zone must match the aggregation time zone. When these two settings are different, the report does not run correctly and the system returns an error. See section How do I configure the Analytics session time zone? for more information about configuring the session time zone.

For an LSP Throughput with Forecast report to be created, the following items must be enabled:

The following table describes the aggregation rules that must be enabled and the accounting policies that must be configured for the NEs on which statistics are to be collected; see the NSP NFM-P Statistics Management Guide for information about configuring an accounting policy. To view the report for granularities other than raw data, the aggregation rules must be enabled; see How do I configure analytics aggregation?.

Table 14-35: LSP Throughput with Forecast report prerequisites

Aggregator name

Monitored object class

Statistics class

Statistics collection

MIB

NE types

MPLS LSP Egress Aggregator

mpls.DynamicLsp

mpls.P2MPDynamicLsp

mpls.SegmentRoutingTeLsp

mpls.mplsLspEgress

Performance statistics

TIMETRA -MPLS- MIB.vRtr MplsLsp Statistics Entry

7705 SAR

7705 SAR-H

7750 SR

Note: 7210 SAS and 7250 IXR are not supported

Use cases

Capacity planning—Use the report to examine LSP throughput data for planning future capacity requirements.

Report characteristics

The following table lists the principal report characteristics.

Table 14-36: LSP Throughput with Forecast report characteristics

Characteristic

Value

Data type

Statistics

Source database

Auxiliary database

LSP types supported

Dynamic, P2MP Dynamic, SR TE

Report inputs

Prompt

Notes

End date

Calendar date or relative date (for example, two days ago) and time

Report Range

Length of time to be reported, in minutes (minutes, min), hours (hours, h), days (days, d), or months (months, m)

Granularity

Aggregation types:

  • None (raw data)

  • Hourly

  • Daily

  • Monthly

NE type

Select individual items.

Name or name pattern for NE

Search using partial names or wildcard (%).

Select individual items.

NE

Select individual items.

Name or name pattern for LSP

Search using partial names or wildcard (%).

Select individual items.

LSP

Select individual items.

You must enter data for this field.

Forecast Periods

The range for the forecast to work. The value is based on the granularity selected. For example, a period of 30 would mean 30 days if the granularity is daily, and 30 months if the granularity is monthly.

Periods per Season

The frequency at which there is a similarity in data. For example, the frequency at which a plot has similar values. The behavior is the same as the forecast period. For example, a period of 7 would mean 7 days if the granularity is daily, and 7 months if the granularity is monthly.

Logo Resource ID

The logo to add to the report. Enter the resource ID for the logo image uploaded to the Images folder, if any. If no logo ID is provided, the logo area will be blank.

Logo Position

Choose Left, Middle or Right. The logo will be placed on the left of the first page of the report for both the left and middle options.

Show report output on one page

Select the check box to enable pagination.

Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.

Drill-down support

No

Example

The following figures show report examples.

Figure 14-45: LSP Throughput with Forecast
LSP Throughput with Forecast