Bandwidth Usage report

Bandwidth Throughput Summary report overview

The Bandwidth Throughput Summary report shows bandwidth utilization by specified radio or Ethernet ports configured as a part of the link across the Wavence NEs. The default display is a set of time series graphs for Rx and Tx Throughput and Rx and Tx summary. You can select a link to use as a baseline on the graph, either the same link or a different link from the data set.

The Bandwidth Throughput Summary report at the link level shows the Rx and Tx throughput on a per link basis for the available Ethernet or Radio ports. The corresponding graphs are plotted for Rx and Tx Throughput within the selected single link.

Note: The report tooltip cannot display large numbers of links. If the data displayed in the tooltip extends past the viewable area, refer to the report instead of the tooltip.

Use cases

Capacity planning—Use the report to examine traffic usage and patterns based on the radio or Ethernet traffic in a network and to plan for capacity requirements.

Limitations

Minimum and maximum throughput aggregation cannot be compared with the minimum and maximum throughput values generated from raw granularity.

Prerequisites

The following table describes the aggregation rules that must be enabled and the accounting policies that must be configured for the NEs on which statistics are to be collected; see the NSP NFM-P Statistics Management Guide for information about configuring an accounting policy. To view the report for granularities other than raw data, the aggregation rules must be enabled; see How do I configure analytics aggregation?.

Table 15-12: Bandwidth Throughput Summary report prerequisites

Aggregator name	Monitored object class	Statistics class	Statistics collection	MIB	NE types
Wavence Ingress Stats Bandwidth Aggregator Wavence Egress Stats Bandwidth Aggregator	Port LAG	Ethernet	Ethernet Aggregate Rx Stats (15Min) Ethernet Aggregate Tx Stats (15Min)	ethAggrMaintRxEntry ethAggrMaintTxEntry	Wavence MSS-1, Wavence MSS-4, Wavence MSS-8, Wavence MSS-O, Wavence MSS-E, Wavence MSS-HE, Wavence MSS-XE, Wavence MSS-1c, Wavence SA, Wavence UBT-SA, Wavence UBT-I, Wavence UBT-T XP, 9500 MPR-A Chassis 4, 9500 MPR-A Chassis 8, 9500 MPR-E Chassis 1, 9500 MPR-E Chassis 4, 9500 MPR-E Chassis 8, 9500 MSS-1c, 9500 MSS-O ANSI, 9500 MSS-O ETSI, 9500 SA Note: The 7705 SAR-H is not supported.

Aggregator name

Monitored object class

Statistics class

Statistics collection

MIB

NE types

Wavence Ingress Stats Bandwidth Aggregator

Wavence Egress Stats Bandwidth Aggregator

Port

LAG

Ethernet

Ethernet Aggregate Rx Stats (15Min)

Ethernet Aggregate Tx Stats (15Min)

ethAggrMaintRxEntry

ethAggrMaintTxEntry

Wavence MSS-1, Wavence MSS-4, Wavence MSS-8, Wavence MSS-O, Wavence MSS-E, Wavence MSS-HE, Wavence MSS-XE, Wavence MSS-1c, Wavence SA, Wavence UBT-SA, Wavence UBT-I, Wavence UBT-T XP, 9500 MPR-A Chassis 4, 9500 MPR-A Chassis 8, 9500 MPR-E Chassis 1, 9500 MPR-E Chassis 4, 9500 MPR-E Chassis 8, 9500 MSS-1c, 9500 MSS-O ANSI, 9500 MSS-O ETSI, 9500 SA

Note: The 7705 SAR-H is not supported.

Report characteristics

The following table lists the principal report characteristics.

Table 15-13: Bandwidth Throughput Summary report characteristics

Characteristic	Value
Data type	Statistics
NE types supported	Wavence MSS-1, Wavence MSS-4, Wavence MSS-8, Wavence MSS-O, Wavence MSS-E, Wavence MSS-HE, Wavence MSS-XE, Wavence MSS-1c, Wavence SA, Wavence UBT-SA, Wavence UBT-I, Wavence UBT-T XP, 9500 MPR-A Chassis 1, 9500 MPR-A Chassis 4, 9500 MPR-A Chassis 8, 9500 MPR-E Chassis 1, 9500 MPR-E Chassis 4, 9500 MPR-E Chassis 8, 9500 MSS-1c, 9500 MSS-O ANSI, 9500 MSS-O ETSI, 9500 SA
Report inputs	Prompt	Notes
	End date	Calendar date or relative date (for example, two days ago) and time
	Granularity	Aggregation types: None (raw data) Hourly Daily Monthly
	Name or name pattern for links	Enter the name pattern of the link
	Links	Select individual items or click Select All.
	Enable Baseline	Select the check box to enable baseline support.
	Baseline End Date	Calendar date or relative date (for example, two days ago) and time
	Baseline Report range	Length of time to be reported, in hours or days
	Baseline Definition	Sub-aggregation types: None (raw data): Raw + Hour of Day, Raw + Hour of Day + Day of Week Hourly: Hour of Day, Hour of Day + Day of Week + Hour of Day + Day of Month Daily: Day of Week, Day of Week + Month of year, Day of Month, Day of Month + Month of year Monthly: Month of year
	Baseline Links	Select individual items or click Select All.
	Tx Threshold	Specify value (Mbps)
	Rx Threshold	Specify value (Mbps)
	Logo Resource ID	The logo to add to the report. Enter the Resource ID of the logo image in the Images folder. The default is the Nokia logo. To create the report without a logo, leave the Logo Resource ID field blank.
	Logo Position	Choose Left, Middle, or Right. The logo appears on the left on the first page of the report if you choose Left or Middle.
	Show report output on one page	Select the check box to enable pagination. Note: Using the Show report output on one page option when creating reports as drill-downs may impact report rendering time. Nokia recommends disabling the Show report output on one page option when creating reports.
	Apply	Applies all the parameters and prepares the report based on the parameters entered
	Reset	Resets all the parameters to default value
Drill-down support	No