How do I create an E-Tree service?

Purpose

Use this procedure to create an E-Tree service. The set of parameters that are available to you is dependant on the intent type that is associated with the service template you select, and may differ from those described in this procedure, which assumes the Nokia-provided E-Tree template is being used.

Before attempting to perform this procedure, ensure that you have read Service creation prerequisites.

Steps
 

Perform How do I create a service template?.


From the Service Management, Services view, click + CREATE.

The Select a service template to start form opens displaying a list of service templates.


Click on an E-Tree service template from the list.

The Create Service form opens with the Template Name parameter populated.


Configure the parameters, as required:

Parameter

Description

Service Name

Specifies the name of the service. Must be unique from other services created using NSP.

NE Service ID

Specifies the NE service ID

MTU

Specifies the MTU of the service

Customer ID

Specifies the customer ID

Description

Describes the service

Admin State

Specifies the initial administrative state of the service upon deployment

Job ID

Specifies the work-order number


In the Site Details panel, click + ADD.

The Add Site form opens.


Configure the required parameters:

Parameter

Description

Device ID

Specifies the device identifier

Site Name

Specifies the site name

Description

Describes the site

Note: If site names and descriptions are added, these will take precedence over any service name and description specified in Step 4, with the first-configured site's name and description taking precedence over all others. As such, these attributes will be displayed in various locations, such as NSP's Model Driven Configurator function and NFM-P.


In the SAP details panel, click + ADD.

The Add SAP form opens.


Configure the parameters, as required:

Parameter

Description

Root Leaf Tag Value

Specifies the Root Leaf Tag Value

E-Tree Leaf

Specifies whether E-Tree Leaf access-circuit is enabled

Port ID

Specifies the port identifier

Inner VLAN Tag

Specifies the inner VLAN tag

Outer VLAN Tag

Specifies the outer VLAN tag

Admin State

Specifies the administrative state of the service

Description

Describes the SAP

Collect Accounting Statistics

Specifies whether or not accounting statistics will be collected


Perform the following to specify an accounting policy to be used:

  1. Click on the Accounting Policy field. The Select Accounting Policy form opens.

  2. Click on an accounting policy in the list, then click SELECT. The Select Accounting Policy form closes.


10 

Configure the parameters, as required:

Parameter

Description

Enable QoS

Specifies whether or not QoS is enabled

Enable IP/IPv6 Filter

Specifies whether or not an IP/IPv6 filter is enabled


11 

If QoS was enabled in Step 10, configure the parameters as required in both the ingress and egress panels:

Parameter

Description

QoS

Match QinQ Dot1p (ingress only)

Specifies the match QinQ Dot1p

QinQ Mark Top Only (egress only)

Specifies whether top Q-tags are marked

SAP Ingress

Policy Name

Specifies the name of the ingress SAP policy

Queuing Type

Specifies the ingress queuing type

SAP Egress

Policy Name

Specifies the name of the egress SAP policy

Queue (click + ADD)

Queue ID

Specifies the unique identifier for the queue

CBS

Specifies the CBS of the queue

MBS

Specifies the MBS of the queue

PIR (kbps)

Specifies the PIR rate of the queue

CIR (kbps)

Specifies the CIR rate of the queue

Policer (click + ADD)

Policer ID

Specifies the unique identifier for the policer

CBS

Specifies the CBS of the policer

MBS

Specifies the MBS of the policer

Policer Control Policy

Policy Name

Specifies the name of the policer control policy

Scheduler Policy

Policy Name

Specifies the name of the scheduler policy

Scheduler (click + ADD)

Scheduler Name

Specifies the name of the scheduler

PIR

Specifies the PIR rate of the scheduler

CIR

Specifies the CIR rate of the scheduler


12 

If an IP/IPv6 filter was enabled in Step 10, configure the parameters as required in both the ingress and egress panels:

Parameter

Description

IP

Specifies the IP filter identifier

IPv6

Specifies the IPv6 filter identifier

Click ADD to add the SAP. The Add SAP form closes.


13 

Perform one of the following:

  1. If required, repeat Step 7 to Step 12 to add additional SAPs.

  2. Continue to Step 14.


14 

Configure the parameters in the MEP panel, as required:

Parameter

Description

MD Admin Name

Specifies the admin-assigned maintenance domain index value

MA Admin Name

Specifies the admin-assigned maintenance association index value

MEP ID

Specifies the MEP identifier

MAC Address

Specifies the MAC address of the MEP

One Way Delay Threshold

Specifies the time limit for one way delay tests

CCM

Specifies whether or not the MEP will generate CCM tests

CCM LTM Priority

Specifies the priority of CCM and LTM messages transmitted by the MEP

Admin State

Specifies the administrative state of the MEP

Click ADD to add the site(s). The Add Site form closes.


15 

In the SDP Details panel, click + ADD.

The Add SDP form opens.


16 

Configure the parameters, as required:

Parameter

Description

E-Tree Root Leaf Tag

Specifies the E-Tree Root Leaf Tag status

E-tree Leaf

Specifies whether E-Tree Leaf access-circuit is enabled

VC Type

Specifies the virtual circuit type, ether or VLAN

SDP Type

Specifies the SDP type, mesh or spoke

Admin State

Specifies the desired state of the service SDP binding

Source Device ID

Specifies the SDP source device identifier

Destination Device ID

Specifies the SDP destination device identifier

Steering Parameter

Specifies the steering parameter used by NSP

SDP ID

Specifies the SDP identifier

Description

Describes the SDP binding

Override VC-ID

Specifies whether or not the VC-ID will serve as the NE service ID for the SDP

VC ID

Specifies the SDP virtual circuit identifier

Click ADD to add the SDP binding. The Add SDP form closes.


17 

Perform one of the following:

  1. Select the Reserve Resources check box and click PLAN to create the service in a Planned state.

  2. Click SAVE to create the service in a Saved state.

  3. Click DEPLOY to create the service in a Deployed state.

See What is the state of my service or tunnel? for more information.

End of steps

© 2024 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.