|
|
1 |
Perform
How do I create a service template?.
|
2 |
From the Service Management, Services view, click + CREATE.
The Select a service template to start form opens displaying a list of service templates.
|
3 |
Click on a L3 VPN service template from the list.
The Create Service form opens with the Template Name parameter populated.
|
4 |
Configure the parameters, as required:
Parameter |
Description |
Service Name |
Specifies the name of the service. Must be unique from other services created using NSP. |
Customer ID |
Specifies the customer ID |
Description |
Describes the service |
Admin State |
Specifies the initial administrative state of the service upon deployment |
Job ID |
Specifies the work-order number |
|
5 |
In the Site Details panel, click + ADD.
The Add Site form opens.
|
6 |
Configure the parameters, as required:
Parameter |
Description |
Device ID |
Specifies the assigned queue group redirect list |
VRF Name |
Specifies the name of the VRF |
Description |
Describes the VRF |
MTU |
Specifies the service MTU |
NE Service ID |
Specifies the NE service ID |
Autonomous System |
Specifies the AS number advertised to peers for this router |
ECMP |
Specifies the maximum number of ECMP routes |
Router ID |
Specifies the unique identifier of the router in the autonomous system |
Export Inactive BGP |
Specifies whether or not to export the best BGP route as a VPN-IP route, even if inactive due to a preferred route from another PE |
Route Distinguisher Type |
Specifies the route distinguisher type |
Route Distinguisher |
Specifies the route distinguisher |
VRF Import |
Specifies the name of the VRF import policy |
VRF Export |
Specifies the name of the VRF export policy |
BGP IPVPN Admin State |
Specifies the BGP IPVPN administrative state. Only applicable on SROS 21.x devices. |
Route Target (click + ADD) |
Target Type |
Specifies the type of route target |
Target Value |
Specifies the route target value |
|
7 |
In the Auto Bind Tunnel panel, configure the required parameters:
Parameter |
Description |
Resolution |
Specifies the MBS of the queue |
Enforce Strict Tunnel Tagging |
Specifies the PIR rate of the queue |
Resolution Filter |
BGP |
Specifies the BGP type for the autobind tunnel |
GRE |
Specifies whether GRE is enabled for the autobind tunnel |
LDP |
Specifies whether LDP is enabled for the autobind tunnel |
RSVP |
Specifies whether RSVP is enabled for the autobind tunnel |
SR ISIS |
Specifies whether SR ISIS is enabled for the autobind tunnel |
SR OSPF |
Specifies whether SR OSPF is enabled for the autobind tunnel |
SR-TE |
Specifies whether SR-TE is enabled for the autobind tunnel |
UDP |
Specifies the UDP type for the autobind tunnel |
RIB API |
Specifies whether RIB API is enabled for the autobind tunnel |
MPLS Fwd Policy |
Specifies whether MPLS Fwd policy is enabled for the autobind tunnel |
SR Policy |
Specifies whether SR policy is enabled for the autobind tunnel |
SR OSPF3 |
Specifies whether segment routing OSPF3 is used for next hop resolution |
|
8 |
As required, click the Enable EVPN MPLS check box in the BGP EVPN panel and configure the parameters:
Parameter |
Description |
Admin State |
Specifies the administrative state of BGP-EVPN MPLS |
Route Distinguisher |
Specifies the route distinguisher |
VRF Import Policy |
Specifies the name of the VRF import policy |
VRF Export Policy |
Specifies the name of the VRF export policy |
Route Target (click + ADD) |
Target Type |
Specifies the type of route target |
Target Value |
Specifies the route target value |
Auto Bind Tunnel |
Resolution |
Specifies the MBS of the queue |
Enforce Strict Tunnel Tagging |
Specifies the PIR rate of the queue |
Resolution Filter |
BGP |
Specifies the BGP type for the autobind tunnel |
GRE |
Specifies whether GRE is enabled for the autobind tunnel |
LDP |
Specifies whether LDP is enabled for the autobind tunnel |
RSVP |
Specifies whether RSVP is enabled for the autobind tunnel |
SR ISIS |
Specifies whether SR ISIS is enabled for the autobind tunnel |
SR OSPF |
Specifies whether SR OSPF is enabled for the autobind tunnel |
SR-TE |
Specifies whether SR-TE is enabled for the autobind tunnel |
UDP |
Specifies the UDP type for the autobind tunnel |
RIB API |
Specifies whether RIB API is enabled for the autobind tunnel |
MPLS Fwd Policy |
Specifies whether MPLS Fwd policy is enabled for the autobind tunnel |
SR Policy |
Specifies whether SR policy is enabled for the autobind tunnel |
SR OSPF3 |
Specifies whether segment routing OSPF3 is used for next hop resolution |
|
9 |
As required, click the Enable Maximum Routes check box in the BGP EVPN panel and configure the parameters:
Parameter |
Description |
Maximum IPv4 Routes |
Max Number of Routes |
Specifies the maximum number of IPv4 routes that are configured on the virtual router |
Log Only |
Specifies whether action is taken when the maximum number of IPv4 routes, held within a VRF context, is reached |
Mid Route Threshold |
Specifies the mid-level water marker for the number of IPv4 routes that the VRF holds |
Maximum IPv6 Routes |
Max Number of Routes |
Specifies the maximum number of IPv6 routes that are configured on the virtual router |
Log Only |
Specifies whether action is taken when the maximum number of IPv6 routes, held within a VRF context, is reached |
Mid Route Threshold |
Specifies the mid-level water marker for the number of IPv6 routes that the VRF holds |
Mc Maximum Routes |
Max Number of MCast Routes |
Specifies the maximum number of multicast routes that are configured on the virtual router |
Log Only |
Specifies whether action is taken when the maximum number of multicast routes, held within a VRF context, is reached |
Mid Route MCast Threshold |
Specifies the mid-level water marker for the number of multicast routes that the VRF holds |
|
10 |
Configure the parameters in the Route Aggregation panel, as required:
Parameter |
Description |
Aggregate (click +ADD) |
Ip Prefix |
Specifies the destination IP address prefix of the aggregate route |
Community |
Specifies the community name that is added to the aggregate route |
Summary Only |
Specifies whether or not to advertise the aggregate route only |
Next Hop |
Specifies the address of the next hop |
SNMP Community |
Specifies the SNMP v1/v2c community name associated with the VPRN |
Ignore NH Metric |
Specifies whether or not to ignore next hop metric |
|
11 |
Configure the parameters in the Bgp Vpn Backup panel, as required:
Parameter |
Description |
Ipv4 |
Specifies whether or not to allow BGP-VPN to be used as backup for IPv4 prefixes |
Ipv6 |
Specifies whether or not to allow BGP-VPN to be used as backup for IPv6 prefixes |
|
12 |
At the bottom of the form, configure the parameters, as required:
Parameter |
Description |
Enable eBGP |
Specifies whether or not the eBGP protocol is enabled |
Enable Static Route |
Specifies whether or not the static routes protocol is enabled |
Enable IS-IS |
Specifies whether or not the IS-IS protocol is enabled |
Enable BGP |
Specifies whether or not the BGP protocol is enabled |
Enable RIP |
Specifies whether or not the RIP protocol is enabled |
|
13 |
In the Interface Details panel, click + ADD.
The Add Interface form opens.
|
14 |
Configure the parameters, as required:
Parameter |
Description |
Interface Name |
Specifies the name of the interface |
Description |
Describes the interface |
Administrative State |
Specifies the administrative state of the interface |
Loopback |
Specifies whether to use the interface as a loopback interface |
IP MTU |
Specifies the interface IP MTU |
Ingress Stats |
Specifies whether or not ingress statistics will be collected |
Monitor Oper Group |
Specifies the operational group to monitor |
|
15 |
If IS-IS was enabled in
Step 12, configure the required parameters in the IS-IS panel:
Parameter |
Description |
IS-IS Instance |
Specifies the instance ID for the IS-IS instance |
Admin State |
Specifies the administrative state of the IS-IS interface |
Passive |
Specifies the passive interface |
Level Capability |
Specifies the routing level for instance |
Interface Type |
Specifies the interface type; broadcast or point-to-point |
|
16 |
If OSPF was enabled in
Step 12, configure the required parameters in the OSPF panel:
Parameter |
Description |
Area ID |
Specifies the area identifier |
Interface Type |
Specifies the interface type, broadcast or point-to-point |
Passive |
Specifies whether to allow the interface to be advertised as an OSPF interface without running the OSPF protocol |
Metric |
Specifies the explicit route cost metric that is applied to the interface |
Authentication Key |
Specifies the authentication key |
Authentication Type |
Specifies the authentication type used on OSPF interface |
BFD Liveliness (click check box) |
Remain Down On Failure |
Specifies whether or not to force adjacency down on failure until session returns |
Admin State |
Specifies the administrative state of the OSPF interface |
|
17 |
If RIP was enabled in
Step 12, configure the required parameter in the RIP panel:
Parameter |
Description |
Group Name |
Specifies the group name |
|
18 |
In the IPv4 panel, configure the required parameters:
Parameter |
Description |
Primary |
Address |
Specifies the primary IPv4 address assigned to the interface |
Prefix Length |
Specifies the primary IPv4 address prefix length |
Secondary (+ ADD) |
Address |
Specifies the secondary IPv4 address assigned to the interface |
Prefix Length |
Specifies the secondary IPv4 address prefix length |
VRRP (+ ADD) |
Virtual Router ID |
Specifies the virtual router identifier for the VRRP virtual router instance |
Passive |
Specifies whether or not to suppress the processing of VRRP advertisement messages |
Admin State |
Specifies the administrative state of VRRP |
Backup |
Specifies virtual router IP addresses for the interface |
Priority |
Specifies the base priority for the VRRP |
Message Interval |
Specifies the interval for sending VRRP advertisement messages |
Ping Reply |
Specifies whether or not to allow non-owner master to reply to ICMP echo requests |
Traceroute Reply |
Specifies whether or not to allow non-owner master to reply to traceroute requests |
Standby Forwarding |
Specifies whether or not to allow standby router to forward traffic |
Neighbor Discovery |
Timeout |
Specifies the timeout for an ARP entry learned on the interface |
Retry Timer |
Specifies the ARP retry interval |
Learn Unsolicited |
Specifies whether or not to learn new entries from any received NA message |
Proactive Refresh |
Specifies whether or not to send a single refresh message before entry timeout |
Populate |
Specifies whether or not to allow static and dynamic hosts to be populated in system ARP cache |
Local Proxy Arp |
Specifies whether or not to enable local proxy ARP on interface |
Proxy Arp Policy |
Specifies the proxy ARP policy name |
Populate (click +ADD) |
Route Type |
Specifies the type of ARP or ND entries that generate host routes |
Route Tag |
Specifies the tag value used with the host route from an ARP/ND entry |
Limit |
Max Entries |
Specifies the maximum number of entries learned on an IP interface |
Log Only |
Specifies whether or not to generate log entries only if limit is reached |
Threshold |
Specifies the threshold value that triggers a warning message |
BFD |
Admin State |
Specifies the administrative state of BFD sessions |
Transmit Interval |
Specifies the BFD transmit interval over this interface |
Receive |
Specifies the BFD receive interval over this interface |
Multiplier |
Specifies the number of consecutive BFD messages missed from the peer |
Echo Receive |
Specifies the minimum echo interval over this interface |
Type |
Specifies the local termination point for the BFD session |
ICMP - Redirects |
Admin State |
Specifies the administrative state of sending ICMP redirect messages |
Number |
Specifies the maximum number of ICMP redirect messages to send |
Seconds |
Specifies the time used to limit the number of ICMP redirect messages |
ICMP - Unreachables |
Admin State |
Specifies the administrative state of sending unreachable messages |
Number |
Specifies the maximum number of unreachable messages to send |
Seconds |
Specifies the time used to limit the number of ICMP unreachable messages |
DHCP |
Admin State |
Specifies the administrative state of DHCP |
Server |
Specifies the IP addresses for DHCP server requests |
|
19 |
In the SAP panel, configure the following parameters for both ingress and egress, as required:
Parameter |
Description |
Port ID |
Specifies the port identifier |
Inner VLAN Tag |
Specifies the inner VLAN tag |
Outer VLAN Tag |
Specifies the outer VLAN tag |
Admin State |
Specifies the administrative state of the service |
Description |
Describes the SAP |
Collect Accounting Statistics |
Specifies whether or not accounting statistics will be collected |
Multi Service Site |
Specifies the multi service site name |
|
20 |
Perform the following to specify an accounting policy to be used:
-
Click on the Accounting Policy field. The Select Accounting Policy form opens.
-
Click on an accounting policy in the list, then click SELECT. The Select Accounting Policy form closes.
|
21 |
Configure the parameters in the Cpu Protection Panel, as required:
Parameter |
Description |
Policy Id |
Specifies the CPM protection policy |
Enable QoS |
Specifies whether or not QoS is enabled |
Enable IP/IPv6 Filter |
Specifies whether or not an IP/IPv6 filter is enabled |
|
22 |
If QoS was enabled in
Step 21, configure the required QoS parameters in both the Ingress and Egress sections:
Parameter |
Description |
QoS |
Match QinQ Dot1p (ingress only) |
Specifies the match QinQ Dot1p |
QinQ Mark Top Only (egress only) |
Specifies whether top Q-tags are marked |
SAP Ingress |
Policy Name |
Specifies the name of the ingress SAP policy |
Queuing Type |
Specifies the ingress queuing type |
SAP Egress |
Policy Name |
Specifies the name of the egress SAP policy |
Queue (click + ADD) |
Queue ID |
Specifies the unique identifier for the queue |
CBS |
Specifies the CBS of the queue |
MBS |
Specifies the MBS of the queue |
PIR |
Specifies the PIR rate of the queue |
CIR |
Specifies the CIR rate of the queue |
Policer (click + ADD) |
Policer ID |
Specifies the unique identifier for the policer |
CBS |
Specifies the CBS of the policer |
MBS |
Specifies the MBS of the policer |
Stat Mode |
Specifies the mode of statistics collected by the policer |
Policer Override Rate |
Specifies the policer override rate |
Policer Control Policy |
Policy Name |
Specifies the name of the policer control policy |
Overrides (click check box) |
Max rate |
Specifies the maximum rate |
Min Thresh Separation |
Specifies the minimum threshold separation |
Priority (click +ADD) |
Priority Level |
Specifies the priority level |
Mbs Contribution |
Specifies the minimum amount of cumulative buffer space allowed |
Scheduler Policy |
Policy Name |
Specifies the name of the scheduler policy |
Scheduler (click + ADD) |
Scheduler Name |
Specifies the name of the scheduler |
PIR |
Specifies the PIR rate of the scheduler |
CIR |
Specifies the CIR rate of the scheduler |
Weight |
Specifies the relative weight of the scheduler to feed the queue |
Cir Weight |
Specifies the weight used at the within-CIR port priority level |
Aggregate Policer (ingress only) |
Rate |
Specifies the enforced aggregate rate for all queues |
Burst |
Specifies the aggregate policer burst |
Cir |
Specifies the aggregate policer CIR |
Cbs |
Specifies the aggregate policer CBS |
Vlan Qos Policy (egress only) |
Policy Name |
Specifies the Egress VLAN QoS policy name |
Port Redirect |
Specifies whether or not to enable Egress VLAN QoS policy port redirect |
Egress Remark Policy (egress only) |
Policy Name |
Specifies the Egress Remark policy name |
Agg Rate or Percent Agg Rate |
Specifies the enforced aggregate rate for all queues |
|
23 |
If a filter was enabled in
Step 21, configure the required filter parameters:
Parameter |
Description |
Aggregate Policer (ingress only) |
Rate |
Specifies the enforced aggregate rate for all queues |
Burst |
Specifies the aggregate policer burst |
Cir |
Specifies the aggregate policer CIR |
Cbs |
Specifies the aggregate policer CBS |
IP/IPv6 Filter |
IP |
Specifies the IP filter identifier |
IPv6 |
Specifies the IPv6 filter identifier |
|
24 |
In the Routed VPLS panel, configure the required parameters:
Parameter |
Description |
VPLS Name |
Specifies the name of the VPLS service |
EVPN Tunnel |
Specifies whether or not to configure the interface as a VPLS EVPN tunnel |
ARP |
Learn Dynamic |
Specifies whether or not dynamic entries learning is enabled |
Advertise Static |
Specifies whether or not advertise static is enabled |
Advertise Static Route Tag |
Specifies the advertise static route tag |
Advertise Dynamic |
Specifies whether or not advertise dynamic is enabled |
Advertise Dynamic Route Tag |
Specifies the advertise dynamic route tag |
|
25 |
In the IPv6 Details panel, configure the required parameters:
Parameter |
Description |
IPv6 (+ ADD) |
IPv6 Address |
Specifies the IPv6 address assigned to the interface |
Prefix Length |
Specifies the IPv6 address prefix length |
Click ADD to add the interface.
The Add Interface form closes.
|
26 |
In the IP Transports panel, click +ADD.
The Add IP Transport form opens.
|
27 |
Configure the parameters, as required:
Parameter |
Description |
Transport Port ID |
Specifies the Transport Port Identifier |
Admin State |
Specifies the administrative state for this IP Transport entry |
Description |
Description of this IP Transport |
Local Host |
Local Host IP Address |
Specifies the IP address of the IP Transport Local Host |
Local Host Port Number |
Specifies the Internet socket port number |
Local Host Protocol |
Specifies the IP protocol that the Local Host |
Session Details |
DSCP |
Specifies the Differentiated Services Code Point (DSCP) for all packets sent to Remote Hosts (within the same IP Transport) |
Forwarding Class |
Specifies the Forwarding Class (FC) for all packets sent to Remote Hosts (within the same IP Transport) |
Filter Unknown Host |
Specifies whether to allow a connection/session with an unknown remote host |
Profile |
Specifies the profile marking for all packets sent to Remote Hosts (within the same IP Transport) |
TCP |
TCP Max Retries |
Specifies the maximum number of consecutive attempts to establish a TCP connection |
TCP Retry Interval |
Specifies the period of time between consecutive attempts to establish a TCP connection |
TCP In Active Timeout |
Specifies the maximum period of time a TCP connection can remain idle before tear-down is initiated |
Remote Host (click +ADD) |
Remote Host Id |
Specifies the identifier for this IP Transport Remote Host |
Name |
Specifies the name assigned to this IP Transport Remote Host |
Description |
Specifies the description of this IP Transport Remote Host |
Remote Host Ip Address |
Specifies the IP address of the IP Transport Remote Host |
Remote Host Port Number |
Specifies the number of a TCP or UDP port |
Check TCP |
Specifies the TCP connection test to be initiated |
Click ADD to add the IP Transport.
The Add IP Transport form closes.
|
28 |
If eBGP was enabled in
Step 12, configure the required parameters:
Parameter |
Description |
Loop Detect |
Specifies the strategy for loop detection in the AS path |
Peer IP Tracking |
Specifies whether or not to enable BGP peer tracking |
Router ID |
Specifies the Router ID for the BGP instance in the AS |
Local AS |
As Number |
Specifies the Local (or virtual) BGP AS number |
Rapid Withdrawal |
Specifies whether or not to send BGP withdrawal UPDATE messages immediately |
Min Route Advertisement |
Specifies the minimum time before a prefix can be advertised to peer |
Next Hop Resolution |
Specifies whether BGP routes can be used to resolve BGP nexthop |
Best Path Selection |
Compare Origin Validation State |
Specifies whether the origin validation state is used in the BGP decision process |
Deterministic MED |
Specifies whether paths will be grouped based on AS before MED attribute comparison |
Origin Invalid Unusable |
Specifies whether routes that have an origin validation state of 'Invalid' can be used |
Ignore NH Metric |
Specifies whether next-hop distance will be ignored during best path selection |
Ignore Router ID |
Specifies whether router ID will be ignored during best path selection |
Always Compare MED |
MED Value |
Specifies the Always Compare MED context |
Strict AS |
Specifies whether MED attributes will be compared from same-neighbor AS routes only |
AS Path Ignore |
IPv4 |
Specifies whether AS path length will be ignored for unlabeled unicast IPv4 routes |
IPv6 |
Specifies whether AS path length will be ignored for unlabeled unicast IPv6 routes |
Label IPv4 |
Specifies whether AS path length will be ignored for labeled unicast IPv4 routes |
Ebgp Ibgp Equal |
IPv4 |
Specifies whether to consider EBGP and IBGP labeled IPv4 routes equal |
IPv6 |
Specifies whether to consider EBGP and IBGP labeled IPv6 routes equal |
Label IPv4 |
Specifies whether to consider EBGP and IBGP unlabeled IPv4 routes equal |
Group (+ ADD) |
Group Name |
Specifies the group name |
Damping |
Specifies whether BGP route damping is used to reduce route flap |
Authentication Key |
Specifies the BGP authentication key for all peers |
Peer AS |
Specifies the peer AS number |
Peer IP Tracking |
Specifies whether BGP peer tracking is enabled |
Prefix Limit (click +ADD) |
Family |
Specifies the address family to which the limit applies |
Maximum |
Specifies the maximum number of routes to be learned from a peer |
Threshold |
Specifies the percentage threshold that triggers a warning message |
Idle Timeout |
Specifies the time which BGP peering remains idle before reconnecting |
Admin State |
Specifies the administrative state of the BGP group |
Export (click check box) |
Policy |
Specifies the export policy name |
Import (click check box) |
Policy |
Specifies the export policy name |
Type |
Specifies the BGP peer type |
Family (click check box) |
Ipv4 |
Specifies whether or not to add support for the IPv4 address family |
Ipv6 |
Specifies whether or not to advertise MP-BGP support for the IPv6 address family |
Mcast Ipv4 |
Specifies whether or not to advertise support for the MCAST-IPv4 address family |
Flow Ipv4 |
Specifies whether or not to advertise support for the flowspec-IPv4 address family |
Flow Ipv6 |
Specifies whether or not to advertise support for the flowspec-IPv6 address family |
Mcast Ipv6 |
Specifies whether or not to advertise support for the MCAST-IPv6 address family |
Label Ipv4 |
Specifies whether or not to advertise support for the label-IPv4 address family |
Neighbor (+ ADD) |
Import Policy |
Specifies the import policy name |
Export Policy |
Specifies the export policy name |
IP Address |
Specifies the IP address that the neighbor uses to communicate with BGP peers |
Group Name |
Specifies the group name |
Peer AS |
Specifies the peer AS number |
Admin State |
Specifies the administrative state of the BGP neighbor |
Split Horizon |
Specifies whether to prevent routes being reflected back to best-route peer |
Authentication Key |
Specifies the BGP authentication key for peer |
Description |
Describes the BGP neighbor |
AS Override |
Specifies whether the peer's ASN will be replaced by the local ASN in AS Path |
Type |
Specifies the BGP peer type |
Family (click check box) |
Ipv4 |
Specifies whether or not to add support for the IPv4 address family |
Ipv6 |
Specifies whether or not to advertise MP-BGP support for the IPv6 address family |
Mcast Ipv4 |
Specifies whether or not to advertise support for the MCAST-IPv4 address family |
Flow Ipv4 |
Specifies whether or not to advertise support for the flowspec-IPv4 address family |
Flow Ipv6 |
Specifies whether or not to advertise support for the flowspec-IPv6 address family |
Mcast Ipv6 |
Specifies whether or not to advertise support for the MCAST-IPv6 address family |
Label Ipv4 |
Specifies whether or not to advertise support for the label-IPv4 address family |
|
29 |
If Enable Static Route was enabled in
Step 12, click + ADD in the Static Route Details panel.
The Add Static Route form opens.
|
30 |
Configure the parameters, as required.
Parameter |
Description |
IP Prefix |
Specifies the IP prefix for the static route |
Prefix Length |
Specifies the prefix length for the static route |
Route Type |
Specifies the static route type |
Tag |
Specifies the static route tag |
Is Blackhole |
Specifies whether the prefix is a blackhole route |
Next Hop (+ ADD) |
IP Address |
Specifies the IP address of the next hop |
Preference |
Specifies the priority of this static route over routes from different sources |
Tag |
Specifies the static route tag |
BFD Liveness |
Specifies whether or not to use Bidirectional Forwarding Detection on this static route |
Admin State |
Specifies the administrative state of next hop |
Indirect (+ ADD) |
IP Address |
Specifies the IP address of the next hop |
Preference |
Specifies the priority of this static route over routes from different sources |
Tag |
Specifies the static route tag |
Admin State |
Specifies the administrative state of next hop |
Click ADD to add the static route.
The Add Static Route form closes.
|
31 |
If Enable IS-IS was enabled in
Step 12, click + ADD in the IS-IS panel.
The Add IS-IS form opens.
|
32 |
Configure the parameters, as required.
Parameter |
Description |
IS-IS Instance |
Specifies the instance ID for the IS-IS instance |
Admin State |
Specifies the administrative state of the IS-IS instance |
Export Policy |
Specifies the export policies that determine exported routes |
Import Policy |
Specifies the import policy names for routes from IGP to route table |
Level Capability |
Specifies the routing level for the instance |
Advertise Router Capability |
Specifies the router capabilities advertisement to neighbors |
Click ADD to add the IS-IS instance.
The Add IS-IS form closes.
|
33 |
If Enable OSPF was enabled in
Step 12, configure the parameters as required:
Parameter |
Description |
Compatible RFC-1583 |
Enables OSPF summary and external route calculations |
Overload On Boot (click check box) |
Timeout |
Specifies the time during which the router operates in overload state before reestablishing normal operations |
Export Policy |
Specifies the export policies that determine exported routes |
Import Policy |
Specifies the import policy names for routes from IGP to route table |
Timers |
Incremental SPF Wait |
Specifies the delay time before an incremental SPF calculation starts |
LSA Accumulate |
Specifies the delay to gather LSAs before advertising to neighbors |
LSA Arrival |
Specifies the minimum delay between receipt of same LSAs from neighbors |
Redistribute Delay |
Specifies the hold down timer for external routes into OSPF |
LSA Generate |
Max LSA Wait |
Specifies the maximum time between two LSAs being generated |
LSA Initial Wait |
Specifies the first wait period between OSPF LSA generation |
LSA Second Wait |
Specifies the hold time between the first and second LSA generation |
Spf Wait |
Max SPF Wait |
Specifies the maximum interval between two consecutive SPF calculations |
SPF Initial Wait |
Specifies the initial SPF calculation delay after a topology change |
SPF Second Wait |
Specifies the hold time between the first and second SPF calculation |
Graceful Restart (click check box) |
Helper Mode |
Enables graceful restart helper for OSPF |
Strict Lsa Checking |
Enables strict LSA checking during graceful restart helper |
|
34 |
If Enable RIP was enabled in
Step 12, configure the parameters as required:
Parameter |
Description |
Export Policy |
Specifies the export policies that determine exported routes |
Import Policy |
Specifies the import policy names for routes from IGP to route table |
Metric In |
Specifies the metric added to routes received from a RIP neighbor |
Metric Out |
Specifies the metric added to routes exported into RIP |
Preference |
Specifies the route preference |
Propagate Metric |
Enables the BGP MED used to configure the RIP metric |
Receive |
Specifies the accepted version on received packets |
Send |
Specifies the RIP version and method used to send RIP updates |
Admin State |
Specifies the administrative state of the IS-IS instance |
Timers |
Update |
Specifies the timer that controls the frequency of updates |
Timeout |
Specifies the RIP timeout timer |
Flush |
Specifies the RIP flush timer |
Group (click +ADD) |
Group Name |
Specifies the group name |
Admin State |
Administrative state of the RIP group |
Export Policy |
Specifies the export policies that determine exported routes |
Import Policy |
Specifies the import policy names for routes from IGP to route table |
Metric In |
Specifies the metric added to routes received from a RIP neighbor |
Metric Out |
Specifies the metric added to routes exported into RIP |
Preference |
Specifies the route preference |
Propagate Metric |
Enables the BGP MED used to configure the RIP metric |
Receive |
Specifies the accepted version on received packets |
Send |
Specifies the RIP version and method used to send RIP updates |
Timers |
Update |
Specifies the timer that controls the frequency of updates |
Timeout |
Specifies the RIP timeout timer |
Flush |
Specifies the RIP flush timer |
|
35 |
Click ADD to add the site.
The Add Site form closes.
|
36 |
In the SDP Details panel, click + ADD.
The Add SDP form opens.
|
37 |
Configure the parameters, as required:
Parameter |
Description |
Source Device ID |
Specifies the SDP source device identifier |
Destination Device ID |
Specifies the SDP destination device identifier |
Steering Parameter |
Specifies the steering parameter used by NSP |
SDP ID |
Specifies the SDP identifier |
Description |
Describes the SDP binding |
Interface |
Species the name of the interface |
Override VC-ID |
Specifies whether or not the VC-ID will serve as the NE service ID for the SDP |
VC ID |
Specifies the SDP virtual circuit identifier |
Click ADD to add the SDP binding. The Add SDP form closes.
|
38 |
Perform one of the following:
-
Select the Reserve Resources check box and click PLAN to create the service in a Planned state.
-
Click SAVE to create the service in a Saved state.
-
Click DEPLOY to create the service in a Deployed state.
See
What is the state of my service or tunnel? for more information.
End of steps |