Configuring physical ports

This chapter provides information about configuring physical ports with the CLI on the node.

Topics in this chapter include:

Configuring Ethernet port parameters

See the 7450 ESS, 7750 SR, 7950 XRS, and VSR Interface Configuration Guide, "Configuring Ethernet port parameters" for information.

Configuring cellular port parameters

The pdn-profile parameter must be configured for the cellular port.

The PDN profile defines the specific APN that the node can connect to. Configure the pdn-profile under the appropriate cellular port. If a PDN profile is not specified, the default profile is used; this default PDN profile cannot be changed.

For more information, see Cellular PDN profile configuration commands and Cellular MDA and cellular port configuration commands.

Configuring serial port parameters

Use the following CLI syntax to configure parameters on an RS-232 serial port.

CLI Syntax:

config# port port-id 
    no shutdown
    serial
        rs232
            character-length {6 | 7 | 8}
            control-lead
                input
                    dtr-dsr high
                    rts-dcd high
                exit
                output
                    dcd-rts high
                    cts-alb high
                    ri-rdl high
                exit
                monitor
                    dtr-dsr off
                    rts-dcd off
                exit
            hold-time {[up hold-time-up] [down hold-time-down]}
            no loopback
            parity {odd | even | mark | space}
            speed {600 | 1200 | 2400 | 4800 | 
9600 | 19200 | 38400 | 57600 | 115200}
            stop-bits {1|2}
            exit
        exit
    exit

The following CLI syntax shows an example of configuring an RS-232 serial port.

Example:

config# port 1/3/2
config>port# no shutdown
config>port# description "RS-232 Serial”
config>port# serial
config>port>serial# rs232
config>port>serial>rs232# character-length 8
config>port>serial>rs232# control-lead
config>port>serial>rs232>control-lead# input
config>port>serial>rs232>control-lead>input# dtr-dsr high
config>port>serial>rs232>control-lead>input# rts-dcd high
config>port>serial>rs232>control-lead>input# exit
config>port>serial>rs232>control-lead# output
config>port>serial>rs232>control-lead>output# dcd-rts high
config>port>serial>rs232>control-lead>output# cts-alb high
config>port>serial>rs232>control-lead>output# ri-rdl high
config>port>serial>rs232>control-lead>output# exit
config>port>serial>rs232>control-lead# monitor
config>port>serial>rs232>control-lead>monitor# dtr-dsr off
config>port>serial>rs232>control-lead>monitor# rts-dcd off
config>port>serial>rs232>control-lead>monitor# exit
config>port>serial>rs232>control-lead# exit
config>port>serial>rs232# hold-time up 100
config>port>serial>rs232# no loopback
config>port>serial>rs232# parity odd
config>port>serial>rs232# speed 9600
config>port>serial>rs232# stop-bits 1
config>port>serial>rs232# exit
config>port>serial# exit
config>port# exit

Use the admin>display-config detail command to display the serial RS-232 port configuration information.

*A:Dut>admin# display-config detail
#--------------------------------------------------
echo "Port Configuration"
#--------------------------------------------------
  .....
port 1/3/2
        description "RS-232 Serial"
        serial
            rs232
                speed 9600
                control-lead
                    input
                        dtr-dsr high
                        rts-dcd high
                    exit
                    output
                        dcd-rts high
                        cts-alb high
                        ri-rdl high
                    exit
                    monitor
                        dtr-dsr off
                        rts-dcd off
                    exit
                exit
                character-length 8
                parity odd
                stop-bits 1
                hold-time up 100 down 100
                    exit
                exit
            exit
        exit
    exit
  .....
#--------------------------------------------------

Configuring RS-232 raw socket serial port parameters

Use the following CLI syntax to configure an RS-232 raw socket serial port.

CLI Syntax:

config# port port-id 
    serial
        rs232
            socket
                description description-string
                rx
                    eop
                        length bytes
                        idle-timeout milliseconds
                        [no] special-char value
                        exit
                    no squelch-delay
                    no unsquelch-delay
                    exit
                tx
                    inter-session-delay ms
                    exit
            exit
        exit

The following CLI syntax shows an example of configuring an RS-232 raw socket serial port.

Example:

config# port 1/3/2
config>port# description "RS-232 Serial"
config>port# serial
config>port>serial# rs232
config>port>serial>rs232# socket
config>port>serial>rs232>socket# rx
config>port>serial>rs232>socket>rx# eop
config>port>serial>rs232>socket>rx>eop# idle-timeout 50
config>port>serial>rs232>socket>rx>eop# length 1500
config>port>serial>rs232>socket>rx>eop# no special-char
config>port>serial>rs232>socket>rx>eop# exit
config>port>serial>rs232>socket>rx# no squelch-delay
config>port>serial>rs232>socket>rx# no unsquelch-delay
config>port>serial>rs232>socket>rx# exit
config>port>serial>rs232>socket# tx
config>port>serial>rs232>socket>tx# inter-session-delay 10
config>port>serial>rs232>socket>tx# exit
config>port>serial>rs232>socket# exit
config>port>serial>rs232# exit
config>port>serial# exit
config>port# exit

Use the admin>display-config detail command to display the raw socket port configuration information.

*A:Dut>admin# display-config detail
#--------------------------------------------------
echo "Port Configuration"
#--------------------------------------------------
  .....
port 1/3/2
        description "RS-232 Serial"
        serial
            rs232
                socket
                    rx
                        eop
                            length 1500
                            idle-timeout 50
                            no special-char
                        exit
                        no squelch-delay
                        no unsquelch-delay
                    exit
                    tx
                        inter-session-delay 10
                    exit
                exit
            exit
        exit
    exit
  .....
#--------------------------------------------------