Access egress QoS policies
This chapter provides information to configure access egress QoS policies using the CLI.
Overview
An access-egress policy defines the queuing for the traffic egressing on the access ports. Access-egress queue policies are used at the Ethernet access port and define the bandwidth distribution for the various FC/queue traffic egressing on the Ethernet access port.
There is one default access egress policy which is identified as policy ID 1. Each policy has eight queues available. The FC-to-queue mapping is predefined and cannot be changed. Queue parameters, for example CIR, PIR, and so on, can be modified. The default policy can be copied but cannot be deleted or modified.
Basic configurations
A basic access egress QoS policy must conform to the following:
have a unique access egress QoS policy ID
have a QoS policy scope of template or exclusive
have queue parameters that can be modified but not deleted
Modifying access egress QoS queues
To modify access-egress queue parameters, specify the following:
queue ID value
Eight queues are identified and are mapped as defined in FC-to-queue ID map.
queue parameters
Egress queues support configuration of CIR and PIR rates.
The following is a sample access egress QoS policy configuration output.
A:card-1>config>qos# info
#--------------------------------------------------
echo "QoS Policy Configuration"
#--------------------------------------------------
....
access-egress 30 create
remarking
queue 1
rate cir 100 pir 4500
exit
queue 2
exit
queue 3
exit
queue 4
exit
queue 5
exit
queue 6
exit
queue 7
exit
queue 8
exit
exit
----------------------------------------------
A:card-1>config>qos#
Applying access egress QoS policies
Apply access egress policies to the 'Ethernet ports' entity.
A policy can be applied to the ports that are in access mode.
Ethernet ports
Use the following CLI syntax to apply an access-egress policy to an Ethernet port.
config>port#
ethernet access egress
qos access-egress-policy-id
The following is a sample port configuration output.
*A:card-1>config>port# info
----------------------------------------------
shutdown
ethernet
access
egress
qos 30
exit
exit
exit
----------------------------------------------
*A:card-1>config>port#
Default access egress QoS policy values
The following are sample access egress default policy parameters.
*A:card-1>config>qos>access-egress# info detail
----------------------------------------------
description "Default Access egress QoS policy."
no remarking
scope template
queue 1
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
queue 2
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
queue 3
adaptation-rule cir closest pir closest
rate 0 pir max
exit
queue 4
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
queue 5
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
queue 6
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
queue 7
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
queue 8
adaptation-rule cir closest pir closest
rate cir 0 pir max
exit
----------------------------------------------
*A:card-1>config>qos>access-egress#
The following table lists the default FC marking values when remarking is enabled on the access egress policy.
|
Default FC value |
dot1p marking values |
|---|---|
|
af: |
dot1p-in-profile 2 dot1p-out-profile 2 |
|
be: |
dot1p-in-profile 0 dot1p-out-profile 0 |
|
ef: |
dot1p-in-profile 5 dot1p-out-profile 5 |
|
h1: |
dot1p-in-profile 6 dot1p-out-profile 6 |
|
h2: |
dot1p-in-profile 4 dot1p-out-profile 4 |
|
l1: |
dot1p-in-profile 3 dot1p-out-profile 3 |
|
l2: |
dot1p-in-profile 1 dot1p-out-profile 1 |
|
nc: |
dot1p-in-profile 7 dot1p-out-profile 7 |
Deleting QoS policies
Every access Ethernet port is associated, by default, with the default access-egress policy (policy-id 1). You can replace the default policy with a customer-configured policy, but you cannot entirely remove the policy from the port configuration. When you remove a non-default access-egress policy, the association reverts to the default policy-id 1.
A QoS policy cannot be deleted until it is removed from all access ports where it is applied.
When a QoS policy is still in use, the following error occurs.
*A:card-1>config>qos# no access-egress 30
MINOR: CLI Could not remove Access egress policy "30" because it is in use.
Removing a policy from the QoS configuration
Use the following syntax to remove a policy.
config>qos# no access-egress policy-id
config>qos# no access-egress 100
config>qos# no access-egress 1010
Access egress QoS policy command reference
Command hierarchies
Configuration commands for 7210 SAS-D and 7210 SAS-Dxp
- config
- qos
- access-egress policy-id [create]
- no access-egress policy-id
- description description-string
- no description
- fc fc-name [create]
- no fc fc-name
- [no] de-mark [force de-value]
- dot1p dot1p-priority
- no dot1p
- dot1p-in-profile dot1p-value
- no dot1p-in-profile
- dot1p-out-profile dot1p-value
- no dot1p-out-profile
- dscp-in-profile dscp-name
- no dscp-in-profile
- dscp-out-profile dscp-name
- no dscp-out-profile
- queue queue-id
- adaptation-rule [cir adaptation-rule] [pir adaptation-rule]
- no adaptation-rule
- rate cir cir-rate [pir pir-rate]
- no rate
- [no] remarking {use-dot1p | use-dscp | all}
- scope {exclusive | template}
- no scope
Show commands
- show
- qos
- access-egress [policy-id] [association| detail]
Command descriptions
Configuration commands
Generic commands
description
Syntax
description description-string
no description
Context
config>qos>access-egress
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command creates a text description stored in the configuration file for a configuration context.
The description command associates a text string with a configuration context to help identify the context in the configuration file.
The no form of this command removes any description string from the context.
Parameters
- description-string
Specifies a text string describing the entity. Allowed values are any string up to 80 characters composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
access-egress
Syntax
access-egress policy-id [create]
no access-egress policy-id
Context
config>qos
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command creates or edits an access-egress QoS policy. The policy can be applied to multiple access ports. The access-egress policy is common to services (SAPs) all configured on that access port.
Any changes made to an existing policy are applied to all access ports on which the policy is specified.
The remarking parameters and queue parameters are used when port-based queuing is configured.
Parameters
- policy-id
Specifies the value that uniquely identifies the access-egress policy.
- create
Specifies that an access-egress policy is created. The create keyword requirement can be enabled or disabled in the environment>create context.
fc
Syntax
fc fc-name [create]
no fc fc-name
Context
config>qos>access-egress
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command defines the fc node within the access-egress QoS policy is used to contain the explicitly defined dot1p marking commands for the fc-name.
If the mapping for the fc-name and marking value is not defined, the node for fc-name is not displayed in the show configuration or save configuration output.
The no form of the command removes the explicit dot1p marking commands for the fc-name.
Parameters
- fc-name
Specifies this FC for which dot1p marking is to be edited. The value specified for fc-name must be one of the predefined FCs in the system.
- create
Specifies that an access-egress policy is created. The create keyword requirement can be enabled or disabled in the environment>create context.
de-mark
Syntax
[no] de-mark[force de-value]
Context
config>qos>access-egress>fc
config>qos>network>egress>fc
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command explicitly defines the marking of the DEI bit for fc fc-name according to the in and out of profile status of the packet (fc-name may be used to identify the dot1p-value).
If no de-value is present, the default values are used for the marking of the DEI bit: for example, 0 for in-profile packets, 1 for out-of-profile ones – see IEEE 802.1ad-2005 standard.
If the de-value is specifically mentioned in the command line it means this value is to be used for all the packets of this FC regardless of their in/out of profile status.
Parameters
- de-value
Specifies the DEI value to use for this FC.
dot1p
Syntax
[no] dot1p dot1p-value
Context
config>qos>access-egress>fc
config>qos>network>egress>fc
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command explicitly defines the egress IEEE 802.1P (dot1p) bits marking for fc-name. When the marking is set, all packets of fc-name that have either an IEEE 802.1Q or IEEE 802.1P encapsulation use the explicitly defined dot1p-value. If the egress packets for fc-name are not IEEE 802.1Q or IEEE 802.1P encapsulated, the dot1p command has no effect.
DEI marking can be enabled using the de-mark command along with this command for the command to take effect. When de-mark command is configured along with this command, then the DEI bit is marked in the packet to indicate the profile of the packet. The DEI bit is marked to 0 to indicate in-profile/green packet and 1 to indicate out-of-profile/yellow packet. If the ‛force de-value’ parameter is specified then the DEI bit is set to specified value for all packets.
If the no form of this command is executed the software will use the dot1p-in-profile and dot1p-out-profile if configured, else it will use default values.
The following rules are applied by the software to determine the dot1p values to when both dot1p command and dot1p-in-profile and dot1p-out-profile command is specified.
-
If de-mark is not configured, the dot1p [in|out]-profile values are considered. Even if dot1p dot1p-value is configured, it is ignored. If the dot1p [in|out]-profile value is not configured, the default values are considered for that FC.
-
If de-mark is configured and if dot1p dot1p-value is configured then it is considered. Else if the dot1p [in|out]-profile value is configured it is considered. In this case dot1p dot1p-value has the precedence over dot1p [in|out]-profile.
Default
no dot1p
Parameters
- dot1p-value
Specifies the 802.1p value to set for in-profile frames in this FC.
dot1p-in-profile
Syntax
dot1p-in-profile dot1p-priority
no dot1p-in-profile
Context
config>qos>access-egress>fc
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
The command enables the context to mark on an egress the in and out of profile status via a specific dot1p combination, similarly with the DEI options. It may be used when the internal in and out of profile status needs to be communicated to an adjacent network/customer device that does not support the DEI bit.
This command explicitly defines the egress IEEE 802.1P (dot1p) bits marking for fc-name. When the marking is set, all packets with in-profile status (or green color) of fc-name that have either an IEEE 802.1Q or IEEE 802.1P encapsulation use the explicitly defined dot1p-value. If the egress packets for fc-name are not IEEE 802.1Q or IEEE 802.1P encapsulated, the dot1p command has no effect.
If DEI marking is enabled using the de-mark command and the command dot1p dot1p-value is used to configure the dot1p value, then this command has no effect. In other words, enabling DEI marking has precedence over this command and the system ignores this command.
When this command is used the DEI Bit is left unchanged by the egress processing if a tag exists. If a new tag is added, the related DEI bit is set to 0.
The no form of this command sets the IEEE 802.1P or IEEE 802.1Q priority bits to 0.
The following rules are applied by the software to determine the dot1p values to when both the dot1p command and the dot1p-in-profile and dot1p-out-profile command is specified:
-
If de-mark is not configured, the dot1p [in|out]-profile values are considered. Even if dot1p dot1p-value is configured it is ignored. If the dot1p [in|out]-profile value is not configured, the default values are considered for that FC.
-
If de-mark is configured, and if the dot1p dot1p-value command is configured, then it is considered. Else if `dot1p [in|out]-profile' value is configured it is considered. In this case dot1p dot1p-valuehas the precedence over dot1p [in|out]-profile.
-
If marking is enabled and both dot1p and dot1-[in|out]-profile commands are not specified, then the value reverts to the default.
Default
0
Parameters
- dot1p-priority
Specifies the 802.1p value to set for in-profile frames in this FC.
dot1p-out-profile
Syntax
dot1p-out-profile dot1p-priority
no dot1p-out-profile
Context
config>qos>access-egress>fc
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
The command enables the context to mark on an egress the in and out of profile status via a specific dot1p combination, similarly with the DEI options. It may be used when the internal in and out of profile status needs to be communicated to an adjacent network/customer device that does not support the DEI bit.
This command explicitly defines the egress IEEE 802.1P (dot1p) bits marking for fc-name. When the marking is set, all packets with out-of-profile status (or yellow color) of fc-name that have either an IEEE 802.1Q or IEEE 802.1P encapsulation use the explicitly defined dot1p-value. If the egress packets for fc-name are not IEEE 802.1Q or IEEE 802.1P encapsulated, the dot1p command has no effect.
If DEI marking is enabled using the de-mark command and the dot1p-value is configured, then this command has no effect. In other words, enabling DEI marking has precedence over this command and the system ignores this command.
When this command is used the DEI Bit is left unchanged by the egress processing if a tag exists. If a new tag is added, the related DEI bit is set to 0.
The no form of this command sets the IEEE 802.1P or IEEE 802.1Q priority bits to 0.
The following rules are applied by software to determine the dot1p values to when both dot1p command and dot1p-in-profile and dot1p-in-profile command is specified:
-
If de-mark is not configured, the dot1p [in|out]-profile values are considered. Even if dot1p dot1p-value command is configured, it is ignored. If the dot1p [in|out]-profile value is not configured, the default values are considered for that FC.
-
If de-mark is configured and if dot1p dot1p-value command is configured, then it is considered. Else if 'dot1p [in|out]-profile' value is configured, it is considered. In this case dot1p dot1p-value, has the precedence over dot1p [in|out]-profile.
-
If marking is enabled and both dot1p dot1p-value and dot1-[in|out]-profile commands are not specified, the value revert to the default.
Default
0
Parameters
- dot1p-priority
Specifies the 802.1p value to set for in-profile frames in this FC.
dscp-out-profile
Syntax
dscp-out-profile dscp-name
no dscp-out-profile
Context
config>qos>access-egress>fc
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command specifies the out-of-profile DSCP name for the FC. When marking is set, the corresponding DSCP value is used to mark all IP packets with out-of-profile status, on the egress of this FC queue.
When multiple DSCP names are associated with the FC at network egress, the last name entered will overwrite the previous value.
The no form of this command reverts to the factory default out-of-profile dscp-name.
Parameters
- dscp-name
Specifies the DSCP name.
dscp-in-profile
Syntax
dscp-in-profile dscp-name
no dscp-in-profile
Context
config>qos>access-egress>fc
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command specifies the in-profile DSCP name for the FC. When marking is set, the corresponding DSCP value is used to mark all IP packets with out-of-profile status, on the egress of this FC queue.
When multiple DSCP names are associated with the FC at network egress, the last name entered will overwrite the previous value.
The no form of this command reverts to the factory default in-profile dscp-name.
Parameters
- dscp-name
Specifies the DSCP name.
queue
Syntax
queue queue-id
Context
config>qos>access-egress
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command specifies a queue for which to modify queue parameters.
Parameters
- queue-id
Specifies the access-egress queue-id associated with an FC according to FC-to-queue ID map.
remarking
Syntax
[no] remarking {use-dot1p | use-dscp | all}
Context
config>qos>access-egress
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command remarks egress packets sent out of access ports and access-uplink ports. For 7210 SAS-D, remarking can be enabled or disabled.
If remarking is enabled without specifying one of the options, by default 'use-dot1p' is used for access-egress and ‟all” is used for network-egress.
The no form of this command disables remarking, which is the default behavior.
Default
no remarking
Parameters
- use-dot1p
Specifies that the dot1p bits are marked in the packet header for all IEEE 802.1q and IEEE 802.1p encapsulated traffic sent out of the access port.
- use-dscp
Specifies that the IP DSCP bits are marked in the packet header for IPv4 traffic sent out of the access port.
- all
Specifies that the dot1p bits are marked in the packet header for all IEEE 802.1q and IEEE 802.1p encapsulated traffic, and in addition the IP DSCP bits are marked in the packet header for all IPv4 traffic sent out the access port.
Access egress queue QoS policy commands
adaptation-rule
Syntax
adaptation-rule [cir adaptation-rule] [pir adaptation-rule]
no adaptation-rule
Context
config>qos>access-egress>queue
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command defines the method used by the system to derive the operational CIR and PIR settings when the queue is provisioned in hardware. For the CIR and PIR parameters individually, the system attempts to find the best operational rate depending on the defined constraint.
The no form of this command removes any explicitly defined constraints used to derive the operational CIR and PIR created by the application of the policy. When a specific adaptation-rule is removed, the default constraints for cir and pir apply.
Default
adaptation-rule pir closest cir closest
Parameters
- cir adaptation-rule
Specifies the adaptation rule and defines the constraints enforced when adapting the CIR rate defined using the queue queue-id rate command. The cir parameter requires a qualifier that defines the constraint used to derive the operational CIR rate for the queue. When the cir parameter is not specified, the default constraint applies. The max (maximum), min (minimum), and closest qualifiers are mutually exclusive.
- pir adaptation-rule
Specifies the adaptation rule and defines the constraints enforced when adapting the PIR rate defined using the queue queue-id rate command. The pir parameter requires a qualifier that defines the constraint used when deriving the operational PIR rate for the queue. When the pir command is not specified, the default constraint applies. The max (maximum), min (minimum), and closest qualifiers are mutually exclusive.
rate
Syntax
rate cir cir-rate [pir pir-rate]
no rate
Context
config>qos>access-egress>queue
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command defines the administrative PIR and CIR parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the port. Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by over subscription factors or available egress bandwidth. The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth.
The rate command can be executed at any time, altering the PIR and CIR rates for all queues created on the access ports.
The no form of this command reverts all queues created using the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).
Parameters
- cir-rate
Specifies that the default administrative CIR used by the queue is overridden. When the rate command is executed, a valid CIR setting must be explicitly defined. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed. Fractional values are not allowed and must be specified as a positive integer.
- pir-rate
Specifies the administrative PIR rate, in kilobits, for the queue. When the rate command is executed, a PIR setting is optional. When the rate command has not been executed, the default PIR of max is assumed. Fractional values are not allowed and must be specified as a positive integer.
The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.
scope
Syntax
scope {exclusive | template}
no scope
Context
config>qos>access-egress
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command configures the scope as exclusive or template. The policy’s scope cannot be changed if the policy is applied to multiple ports.
The no form of this command sets the scope of the policy to the default of template.
Default
template
Parameters
- exclusive
Specifies that the policy can only be applied to one port. If a policy with an exclusive scope is assigned to a second interface, an error message is generated. If the policy is removed from the exclusive interface, it becomes available for assignment to another exclusive interface. The system default policies cannot be put into the exclusive scope. An error occurs if scope exclusive is executed in the default access-egress policy (policy-id 1).
- template
Specifies that the policy can be applied to multiple ports on the router.
access-egress
Syntax
access-egress [policy-id] [association | detail]
Context
show>qos
Platforms
Supported on all 7210 SAS platforms as described in this document
Description
This command displays access-egress QoS policy information.
Parameters
- policy-id
Displays the policy ID of the access-egress policy.
- association
Displays associations related to the specified access-egress policy.
- detail
Displays detailed policy information including the policy associations.
Output
The following output is an example of access-egress QoS policy information, and Access-egress labels and descriptions describes the output fields.
Sample outputA:Dut-A>show>qos# access-egress
===============================================================================
Access Egress Policies
===============================================================================
Policy-Id Scope Description
-------------------------------------------------------------------------------
1 Template Default Access egress QoS policy.
===============================================================================
A:Dut-A>show>qos#
A:Dut-A>show>qos# access-egress 1 detail
===============================================================================
QoS Access Egress
===============================================================================
-------------------------------------------------------------------------------
Policy-id : 1 Scope : Template
Remark : False Remark Pol Id: 2
Description : Default Access egress QoS policy.
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId CIR CIR Adpt Rule PIR PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1 0 closest max closest
Queue2 0 closest max closest
Queue3 0 closest max closest
Queue4 0 closest max closest
Queue5 0 closest max closest
Queue6 0 closest max closest
Queue7 0 closest max closest
Queue8 0 closest max closest
-------------------------------------------------------------------------------
Queue Mode and Weight Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId Mode Weight
-------------------------------------------------------------------------------
Queue1 weighted 1
Queue2 weighted 1
Queue3 weighted 1
Queue4 weighted 1
Queue5 weighted 1
Queue6 weighted 1
Queue7 weighted 1
Queue8 weighted 1
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId State Start-Avg(%) Max-Avg(%) Max-Prob(%)
-------------------------------------------------------------------------------
Queue1 Down 70 90 75
Queue2 Down 70 90 75
Queue3 Down 70 90 75
Queue4 Down 70 90 75
Queue5 Down 70 90 75
Queue6 Down 70 90 75
Queue7 Down 70 90 75
Queue8 Down 70 90 75
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId State Start-Avg(%) Max-Avg(%) Max-Prob(%)
-------------------------------------------------------------------------------
Queue1 Down 50 75 75
Queue2 Down 50 75 75
Queue3 Down 50 75 75
Queue4 Down 50 75 75
Queue5 Down 50 75 75
Queue6 Down 50 75 75
Queue7 Down 50 75 75
Queue8 Down 50 75 75
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId CBS MBS Time Average Factor Queue-Mgmt
-------------------------------------------------------------------------------
Queue1 def def 7 default
Queue2 def def 7 default
Queue3 def def 7 default
Queue4 def def 7 default
Queue5 def def 7 default
Queue6 def def 7 default
Queue7 def def 7 default
Queue8 def def 7 default
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
===============================================================================
A:Dut-A>show>qos#
A:Dut-A>show>qos#
|
Label |
Description |
|---|---|
|
Scope |
Exclusive — Specifies that this policy can be applied only to a single access-egress port |
|
Template — Specifies that this policy can be applied to multiple access ports on the router |
|
|
Description |
A text string that helps identify the policy context in the configuration file |
|
Queue Rates and Rules |
|
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
|
CIR |
Specifies the administrative CIR parameters for the queue. The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth |
|
CIR Adpt Rule |
min — The operational CIR for the queue is equal to or greater than the administrative rate specified using the rate command |
|
max — The operational CIR for the queue is less than or equal to the administrative rate specified using the rate command |
|
|
closest — The operational CIR for the queue is the rate closest to the rate specified using the rate command without exceeding the operational PIR |
|
|
PIR |
Specifies the administrative PIR parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the access port |
|
PIR Adpt Rule |
min — The operational PIR for the queue is equal to or greater than the administrative rate specified using the rate command |
|
max — The operational PIR for the queue is less than or equal to the administrative rate specified using the rate command |
|
|
closest — The operational PIR for the queue is the rate closest to the rate specified using the rate command |
|
|
High Slope/Low slope |
|
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
|
State |
Displays the state of the queue The state of the queue can be either ‟Up” or ‟Down” |
|
Start Avg |
Specifies the low priority or high priority RED slope position for the shared buffer average utilization value, where the packet discard probability starts to increase above zero |
|
Max Avg |
Specifies the percentage of the shared buffer space for the buffer pool, at which point the drop probability becomes ‟1” This parameter is expressed as a decimal integer |
|
Max Prob |
Specifies the high priority RED slope position for the maximum non-one packet discard probability value before the packet discard probability rises directly to one |
|
Burst Sizes and Time Average Factor |
|
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
|
CBS |
Displays the configured CBS value |
|
MBS |
Displays the configured MBS value |
|
Time Average Factor |
Displays the value of the time average factor in use |