Service egress policies on 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
This section provides information to configure Service egress QoS policies using the command line interface.
Service egress policies are supported only on the 7210 SAS-Mxp, 7210 SAS-R6 IMM-b, and 7210 SAS-R12 IMM-b. It is not supported on the 7210 SAS-R6 IMM-c, 7210 SAS-R12 IMM-c, 7210 SAS-T, and 7210 SAS-Sx/S 1/10GE devices.
Overview
On the 7210 SAS-R6 and 7210 SAS-R12, only unicast traffic sent out of RVPLS SAPs uses per-SAP egress queues. BUM traffic sent out of RVPLS SAPs uses per-port egress queues.
The Service Egress policy defines the Service Level Agreement (SLA) for service packets as they egress on the access SAP. Service Egress QoS policies allow the definition of queue parameters along with a remark policy.
Service Egress Qos policies are available for use only when per SAP egress queues (SAP-based queuing mode) are used. It is not available when port-based queuing mode (that is, with per access port egress queues) is in use.
The 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12, on port egress, use either port-based egress queuing and shaping or SAP-based egress queuing and shaping for all SAPs configured on the port. The config system global-resource-profile qos port-scheduler-mode command on the 7210 SAS-R6 and 7210 SAS-R12 and the config system resource-profile qos port-scheduler-mode command on the 7210 SAS-Mxp allows the user to select the mode for all SAPs configured on either access ports or hybrid ports. When port-scheduler-mode is enabled, the software allocates eight egress queues per port (access port or hybrid port). See Schedulers on 7210 SAS-R6 and 7210 SAS-R12 for more information. When port-scheduler-mode is disabled, the software allocates eight egress queues per SAP, which are configured using service egress policies.
Basic configurations
To use per SAP service egress policies, the following must be configured:
Disable port-scheduler mode using the config system res-prof qos no port-scheduler-mode command on the 7210 SAS-Mxp, and config system global-res-prof no port-scheduler-mode on the 7210 SAS-R6 and 7210 SAS-R12.
Ensure resources are available for use by SAP egress queues in the ingress-internal-tcam resources pool using the config system resource-profile ingress-internal-tcam qos-sap-egress-resource command.
A basic service egress QoS policy must conform to the following:
have a unique service egress QoS policy ID
have a QoS policy scope of template or exclusive
have at least one forwarding class queue
Create a SAP egress policy
To create a new SAP Egress policy, define the following:
a SAP egress policy name
a brief description of the policy features
the queue parameters for all the queues
Use the following syntax to configure a SAP egress policy.
A:Dut-A>config>qos# sap-egress
- no sap-egress <policy-id>
- sap-egress <policy-id> [create]
<policy-id> : [1..65535]|<name:64 char max>
<create> : keyword - mandatory while creating an entry.
[no] description - Description for this sap-egress policy
[no] queue + Configure a queue
[no] remark - Specify Remarking policy for this policy
[no] remarking - Enable/disable remarking
[no] scope - Specify scope of the policy
The following is a sample SAP Egress policy configuration output for the 7210 SAS-Mxp.
*A:sim_dutc>config>qos>sap-egress# info detail
----------------------------------------------
description "Default SAP egress QoS policy."
scope template
no remarking
remark 2
queue 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
queue-mode weighted
weight 1
exit
queue 2
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
queue-mode weighted
weight 1
exit
queue 3
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
queue-mode weighted
weight 1
exit
queue 4
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
queue-mode weighted
weight 1
exit
queue 5
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
queue-mode weighted
weight 1
exit
----------------------------------------------
A:Dut-B>config>qos>sap-egress#
The following is a sample SAP Egress configuration output for the 7210 SAS-R6 and 7210 SAS-R12.
*A:SAS>config>qos>sap-egress# info detail
----------------------------------------------
description "Default SAP egress QoS policy."
scope template
no remarking
remark 2
queue 1
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 2
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 3
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 4
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 5
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 6
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 7
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
queue 8
port-parent cir-level 1 pir-weight 1
adaptation-rule pir closest cir closest
rate cir 0 pir max
queue-mgmt "default"
exit
----------------------------------------------
*A:SAS>config>qos>sap-egress#
Editing QoS policies
Existing policies and entries can be edited through the CLI or NMS. The changes are applied immediately to all services where the policy is applicable.
To prevent configuration errors, perform the following:
Copy the policy to a work area.
Edit the policy.
Overwrite the original policy.
Service egress policy command reference
Command hierarchies
Configuration commands for 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
config
- qos
- sap-egress policy-id [create]
- no sap-egress policy-id
- [no] description description-string
- queue queue-id
- [no] adaptation-rule [pir adaptation-rule] [cir adaptation-rule]
- queue-mgmt name
- no queue-mgmt
- queue-mode queue-mode
- no queue-mode
- [no] rate cir cir-rate pir pir-rate
- weight weight
- no weight
- scope {exclusive | template}
- no scope
- [no] remark policy-id
- [no] remarking
Operational commands
config
- qos
- copy sap-egress src-pol dst-pol [overwrite]
Show commands
show
- qos
- sap-egress [policy-id] [detail | association]
Command descriptions
Configuration commands
Generic commands
description
Syntax
description description-string
no description
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command creates a text description stored in the configuration file for a configuration context.
The description command associates a text string with a configuration context to help identify the context in the configuration file.
The no form of this command removes any description string from the context.
Parameters
- description-string
Specifies a text string describing the entity. Allowed values are any string up to 80 characters composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
SAP egress queue QoS policy commands
adaptation-rule
Syntax
adaptation-rule [cir adaptation-rule] [pir adaptation-rule]
no adaptation-rule
Context
config>qos>sap-egress>queue
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command defines the method used by the system to derive the operational CIR and PIR rates when the queue is provisioned in hardware. For the cir and pir parameters, the system attempts to find the best operational rate depending on the defined constraint.
The no form of this command removes any explicitly defined constraints used to derive the operational CIR and PIR created by the application of the policy. When a specific adaptation-rule is removed, the default constraints for cir and pir apply.
Default
adaptation-rule pir closest cir closest
Parameters
- cir adaptation-rule
Specifies the adaptation rule and defines the constraints enforced when adapting the CIR rate defined using the queue queue-id rate command. The cir parameter requires a qualifier that defines the constraint used to derive the operational CIR rate for the queue. When the cir parameter is not specified, the default constraint applies. The max (maximum), min (minimum), and closest qualifiers are mutually exclusive. Supported hardware rates and burst step sizes for CIR and PIR values on the 7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12, 7210 SAS-Sx/S 1/10GE, and 7210 SAS-T lists the supported hardware step-size rates.
- pir adaptation-rule
Specifies the adaptation rule and defines the constraints enforced when adapting the PIR rate defined using the queue queue-id rate command. The pir parameter requires a qualifier that defines the constraint used when deriving the operational PIR rate for the queue. When the pir command is not specified, the default constraint applies. The max (maximum), min (minimum), and closest qualifiers are mutually exclusive. Supported hardware rates and burst step sizes for CIR and PIR values on the 7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12, 7210 SAS-Sx/S 1/10GE, and 7210 SAS-T lists the supported hardware step-size rates.
queue
Syntax
queue queue-id create
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command configures queue parameters.
Parameters
- queue-id
Specifies the ID of the queue.
- create
Keyword to create a network queue policy.
sap-egress
Syntax
sap-egress policy-id [create]
Context
config>qos
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command configures a SAP Egress policy. The SAP egress policy determines the QoS treatment to packets on service egress.
When the policy is created, by default only one queue is created. The user can create up to eight queues and associate each queue to different FCs on the SAPs to which this sap-egress policy is attached. A SAP egress policy allows the user to define the queue parameters for the eight queues.
Default
1
Parameters
- policy-id
Specifies the ID of the SAP Egress policy.
- create
Keyword to create a SAP Egress policy
remark
Syntax
remark policy-id
no remark
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command specifies the remarking policy ID to use for marking packets on service egress (also known as SAP egress).
The remarking policy ID must be associated with the appropriate sap-egress policy and remarking must be enabled in the sap-egress policy to enable marking of packets sent out of the SAP. Only remarking policy of type dot1p, or dot1p-lsp-exp-shared is allowed to be used when the remark policy is associated with sap-egress. See Summary of remark policy and attachment points for 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12 for more information on remark policies.
On the 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12, remarking is user configurable and supports SAP-based marking per SAP and port-based marking per access port. See Access egress QoS policies on 7210 SAS-Mxp and Summary of remark policy and attachment points for 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12 for more information about access port-based marking capabilities.
The no form of this command removes the explicit association of the remark policy and associates the default remark policy. If remarking is enabled and no remark policy is executed, the default remark policy is used to mark packets sent out. If no remark policy is executed and remarking is disabled, packets are not remarked.
Parameters
- policy-id
Specifies the remark policy.
remarking
Syntax
no remarking
remarking
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command enables the system to remark egress packets sent out of service egress (also known as Access SAP egress).
When remarking is enabled, the remark policy configured in the QoS policy context is used to determine the FC to QoS bit mapping. For example, when remarking is enabled in the -egress QoS policy, the remark policy associated with sap-egress QoS policy is used to determine the FC to dot1p mapping to use for marking packets sent out of access ports.
See Remark policies and Summary of remark policy and attachment points for 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12 for more information about the remark policy that can be used to configure FC to priority bit markings in different QoS policies associated with different service entities.
The no form of this command disables remarking.
Default
no remarking
scope
Syntax
scope {exclusive | template}
no scope
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command configures the scope as exclusive or template. The policy’s scope cannot be changed if the policy is applied to an interface multiple ports.
The no form of this command reverts the scope of the policy to the default.
Default
template
Parameters
- exclusive
Specifies that the policy can only be applied to one interface or port. If a policy with an exclusive scope is assigned to a second interface, an error message is generated. If the policy is removed from the exclusive interface, it will become available for assignment to another exclusive interface. The system default policies cannot be put into the exclusive scope. An error will be generated if scope exclusive is executed in any policies with a policy-id equal to default QoS policies are configured with template scope. An error is generated if you try to modify the scope parameter from template to exclusive scope on default policies.
- template
Specifies that the policy can be applied to multiple interfaces or ports on the router.
queue-mgmt
Syntax
[no] queue-mgmt name
Context
config>qos>sap-egress>queue
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command associates the specified queue management policy with this queue.
The queue management policy is used to specify the queue buffer parameters and queue slope policy parameters.
The no form of this command associates the default SAP egress queue management policy with this queue.
Parameters
- name
Specifies the name of the queue management policy, up to 32 characters.
queue-mode
Syntax
[no] queue-mode queue-mode
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command determines whether the queue operates in strict or weighted mode.
The no form of this command reverts the queue mode to the default.
Default
weighted
Parameters
- queue-mode
Specifies the queue mode.
strict — Specifies that the scheduler schedules the queue in order of their priority in the two passes, the CIR loop and the PIR loop.
weighted — Specifies that the scheduler examines these queues in two passes - CIR loop and PIR loop. In the CIR loop, it distributes the available bandwidth to all the strict and then weighted queues in round-robin up to the configured CIR rate. It examines the weighted queues in the PIR loop, after examining all the strict queues and distributes the available bandwidth, if any, in the proportion of the configured weights.
rate
Syntax
rate cir cir-rate-in-kbps [pir pir-rate-in-kbps]
no rate
Context
config>qos>sap-egress>queue
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command defines the administrative Peak Information Rate (PIR) and the administrative Committed Information Rate (CIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the port. Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth. The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth.
The rate command can be executed at anytime, altering the PIR and CIR rates for all queues created on the access ports.
The no form of this command reverts all queues created with the queue ID by association with the QoS policy to the default PIR (max) and CIR (0) parameters.
Default
rate cir 0 pir max
Parameters
- cir cir-rate-in-kbps
Specifies the administrative CIR rate, in kilobits, for the queue. The cir parameter overrides the default administrative CIR used by the queue. If the rate command is not executed or the cir parameter is not explicitly specified, the default CIR value is used.
- pir pir-rate-in-kbps
Specifies the administrative PIR rate, in kilobits, for the queue. When the rate command is executed, a PIR setting is optional. If the rate command is not executed, the default PIR of maximum value is used. The max default specifies the amount of bandwidth in kilobits per second (thousand bits per second). The max value is mutually exclusive to the pir-rate value.
weight
Syntax
[no] weight weight
Context
config>qos>sap-egress>queue
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command configures the weight of the queue.
For queues configured in weighted mode, the CIR of the queues are met if bandwidth is available and the configured weights are considered in the PIR loop. The configured weight determines the proportion of available bandwidth that is given to this queue in comparison to other queues contending for bandwidth at the same priority level.
The no form of this command reverts the weight to the default value.
Default
1
Parameters
- weight
Specifies the value for the weight parameter. The value is an integer value which specifies the proportion of available bandwidth to be allocated to this queue relative to other queues.
scope
Syntax
scope {exclusive | template}
no scope
Context
config>qos>sap-egress
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command configures the scope as exclusive or template. The policy’s scope cannot be changed if the policy is applied to an interface multiple ports.
The no form of this command reverts the scope of the policy to the default.
Default
template
Parameters
- exclusive
Specifies that the policy can only be applied to one interface port. If a policy with an exclusive scope is assigned to a second interface an error message is generated. If the policy is removed from the exclusive interface, it will become available for assignment to another exclusive interface. The system default policies cannot be put into the exclusive scope. An error will be generated if scope exclusive is executed in any policies with a policy ID equal to 1.
- template
Specifies that the policy can be applied to multiple interface ports on the router.
Default QoS policies are configured with template scope. An error is generated if you try to modify the scope parameter from template to exclusive scope on default policies.
Operational commands
copy
Syntax
copy sap-egress src-pol dst-pol [overwrite]
Context
config>qos
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command copies the existing SAP egress QoS policy entries to another SAP egress QoS policy.
The copy command is a configuration level maintenance tool used to create new policies using existing policies. It also allows bulk modifications to an existing policy with the use of the overwrite keyword.
If the destination policy already exists, the overwrite keyword must be specified.
Parameters
- src-pol
Specifies the source policy.
- dst-pol
Specifies the destination policy.
- overwrite
Keyword to overwrite the information in the destination policy by the information in the source policy.
Show Commands
sap-egress
Syntax
sap-egress [policy-id] [association | detail]
Context
show>qos
Platforms
7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12
Description
This command displays SAP egress QoS policy information.
Parameters
- policy-id
Displays the policy ID of the sap-egress policy.
- association
Displays associations related to the specified sap-egress policy.
- detail
Displays detailed policy information including the policy associations.
Output
The following outputs are examples of SAP egress QoS policy information. The associated tables describe the output fields.
Sample output (7210 SAS-Mxp), Output fields: SAP egress QoS policy (7210 SAS-Mxp)
Sample output (7210 SAS-R6 and 7210 SAS-R12), Output fields: SAP egress QoS policy (7210 SAS-R6 and 7210 SAS-R12)
A:7210SAS>show>qos# sap-egress
===============================================================================
Sap Egress Policies
===============================================================================
-------------------------------------------------------------------------------
Policy-id Remark Remark Scope Name Description
Policy-id
-------------------------------------------------------------------------------
1 False 2 Template default Default SAP egress
===============================================================================
A:7210SAS>show>qos#
| Label | Description |
|---|---|
Policy-Id |
The ID that uniquely identifies the policy |
Remark |
True — Remarking is enabled for all the dot1q-tagged packets that egress the ports on which the sap-egress QoS policy is applied and remarking is enabled False — Remarking is disabled for the policy |
Remark Pol Id |
Displays the policy ID of the remarking policy |
Accounting |
Specifies whether the accounting mode is packet-based or frame-based |
Scope |
Exclusive — Implies that this policy can be applied only to a single access egress port Template — Implies that this policy can be applied to multiple access ports on the router |
Description |
A text string that helps identify the policy’s context in the configuration file |
A:SAS>config>qos# show qos sap-egress 1 detail
===============================================================================
QoS Sap Egress
===============================================================================
-------------------------------------------------------------------------------
Sap Egress Policy (1)
-------------------------------------------------------------------------------
Scope : Template
Remark : False Remark Pol Id : 2
Accounting : frame-based
Description : Default SAP egress QoS policy.
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId CIR CIR Adpt Rule PIR PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1 0 closest max closest
Queue2 0 closest max closest
Queue3 0 closest max closest
Queue4 0 closest max closest
Queue5 0 closest max closest
Queue6 0 closest max closest
Queue7 0 closest max closest
Queue8 0 closest max closest
-------------------------------------------------------------------------------
Parent Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId Port CIR Level PIR Weight
-------------------------------------------------------------------------------
Queue1 True 1 1
Queue2 True 1 1
Queue3 True 1 1
Queue4 True 1 1
Queue5 True 1 1
Queue6 True 1 1
Queue7 True 1 1
Queue8 True 1 1
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId State Start-Avg(%) Max-Avg(%) Max-Prob(%)
-------------------------------------------------------------------------------
Queue1 Down 70 90 75
Queue2 Down 70 90 75
Queue3 Down 70 90 75
Queue4 Down 70 90 75
Queue5 Down 70 90 75
Queue6 Down 70 90 75
Queue7 Down 70 90 75
Queue8 Down 70 90 75
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId State Start-Avg(%) Max-Avg(%) Max-Prob(%)
-------------------------------------------------------------------------------
Queue1 Down 50 75 75
Queue2 Down 50 75 75
Queue3 Down 50 75 75
Queue4 Down 50 75 75
Queue5 Down 50 75 75
Queue6 Down 50 75 75
Queue7 Down 50 75 75
Queue8 Down 50 75 75
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId CBS MBS Time Average Factor Queue-Mgmt
-------------------------------------------------------------------------------
Queue1 def def 7 default
Queue2 def def 7 default
Queue3 def def 7 default
Queue4 def def 7 default
Queue5 def def 7 default
Queue6 def def 7 default
Queue7 def def 7 default
Queue8 def def 7 default
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
Service-Id : 1 (Epipe) Customer-Id : 1
- SAP : 1/1/1:1
Service-Id : 101 (Epipe) Customer-Id : 1
- SAP : 1/1/2:101
-------------------------------------------------------------------------------
Mirror SAPs
-------------------------------------------------------------------------------
No Mirror SAPs Found.
===============================================================================
A:SAS>config>qos#
| Label | Description |
|---|---|
Policy-Id |
Displays the ID that uniquely identifies the policy |
Remark |
True — Remarking is enabled for all the dot1q-tagged packets that egress the ports on which the SAP-egress QoS policy is applied and remarking is enabled False — Remarking is disabled for the policy |
Remark Pol Id |
Displays the policy ID of the remarking policy |
Accounting |
Specifies whether the accounting mode is packet-based or frame-based |
Scope |
Exclusive — Specifies that this policy can be applied only to a single access egress port Template — Specifies that this policy can be applied to multiple access ports on the router |
Description |
A text string that helps identify the policy context in the configuration file |
Queue Rates and Rules |
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
Explicit/Default |
Explicit — Specifies the egress dot1p bits marking for fc-name, if explicitly configured Default —Specifies the default dot1p value according to FC-Dot1p marking map as listed in Default remarking policy for dot1p on 7210 SAS-R6 and 7210 SAS-R12 , if explicit values are not configured |
CIR |
Specifies the administrative CIR parameters for the queue The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. |
CIR Adpt Rule |
min — The operational CIR for the queue is equal to or greater than the administrative rate specified using the rate command max — The operational CIR for the queue is less than or equal to the administrative rate specified using the rate command closest — The operational CIR for the queue is the rate closest to the rate specified using the rate command without exceeding the operational PIR |
PIR |
Specifies the administrative PIR parameters for the queue The PIR defines the maximum rate that the queue can transmit packets through the access port. |
PIR Adpt Rule |
min — The operational PIR for the queue is equal to or greater than the administrative rate specified using the rate command max — The operational PIR for the queue is less than or equal to the administrative rate specified using the rate command closest — The operational PIR for the queue is the rate closest to the rate specified using the rate command |
Parent Details |
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
Port |
Indicates whether the parent scheduler is a port scheduler |
CIR Level |
Displays the priority of the queue in the CIR loop |
PIR Weight |
Displays the weight of the queue used in the PIR loop |
High Slope/Low slope |
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
State |
Displays the state of the queue The state of the queue can be either ‟Up” or ‟Down”. |
Start Avg |
Specifies the low priority or high priority RED slope position for the shared buffer average utilization value, where the packet discard probability starts to increase above zero |
Max Avg |
Specifies the percentage of the shared buffer space for the buffer pool at which point the drop probability becomes ‟1” This parameter is expressed as a decimal integer. |
Max Prob |
Specifies the high-priority RED slope position for the maximum non-one packet discard probability value before the packet discard probability rises directly to one |
Burst Sizes and Time Average Factor |
|
QueueId |
Displays the queue identifier associated with the SAP-egress QoS policy |
CBS |
Displays the configured CBS value |
MBS |
Displays the configured MBS value |
Time Average Factor |
Displays the value of the time average factor in use |
Queue-Mgmt |
Displays the queue management policy in use |
Service Associations |
|
Service-Id |
The unique service ID number that identifies the service in the service domain |
Customer-Id |
Specifies the customer ID that identifies the customer to the service |
SAP |
Specifies the SAP within the service where the SAP-egress policy is applied |