VLL services

This section provides information about Virtual Leased Line (VLL) services and implementation notes.

Ethernet pipe (Epipe) services

This section provides information about the Epipe service and implementation notes.

Epipe service overview

An Epipe service is a Layer 2 point-to-point service where the customer data is encapsulated and transported across a service provider network. An Epipe service is completely transparent to the subscriber data and protocols. The Epipe service does not perform any MAC learning. A local Epipe service consists of two SAPs on the same node, whereas a distributed Epipe service consists of two SAPs on different nodes.

Each SAP configuration includes a specific port on which service traffic enters the 7210 SAS from the customer side (also called the access side). Each port is configured with an encapsulation type. If a port is configured with an IEEE 802.1Q (referred to as dot1q) encapsulation, then a unique encapsulation value (ID) must be specified.

The following figure shows Epipe/VLL service.

Figure 1. Epipe/VLL service

Support for processing of packets received with more than 2 tags on a QinQ SAP in Epipe service (only on 7210 SAS devices configured in network mode)

To forward packets with 2 or more tags using a QinQ SAP, a new Epipe service type is available for use when 7210 SAS devices are operating in ‛network’ mode. This new service allows for configuration of a QinQ SAP as one endpoint and the following service entities as the other endpoint:

  • MPLS spoke-SDP with vc-type set to vc-vlan: The VC VLAN tag to be must match the inner tag VLAN ID value specified in the QinQ SAP.

  • dot1q SAP: The VLAN value configured for the dot1q SAP must match the inner-tag VLAN ID value of the QinQ SAP.

  • QinQ SAP: The inner VLAN tag of both QinQ SAPs configured in the service must be the same.

The device processes the packet as follows in the forward direction:

  • If the packet is received on a QinQ SAP, assign an incoming packet to this service based on matching the outermost two tags in the packet header (that is, the first two tags in the packet header). It strips only the outermost tag (only a single tag) on ingress and forward the rest on to the other endpoint in the service (as follows).

  • If the other endpoint the packet is sent out of is a MPLS SDP, then MPLS encapsulation is added.

  • If the other endpoint the packet is sent out of is a dot1q SAP packet is forwarded as is, without any egress VLAN checks. The operator must ensure the inner tag of the packet matches the dot1q VLAN value.

  • If the other endpoint the packet is sent out of is another QinQ SAP (for example, Q1.Q2 SAP), then another tag (that is, Q2 tag) is added to the packet and sent out of the QinQ SAP.

In the reverse direction, the device processes the packet as follows:

  • When traffic is received on the MPLS SDP, the VC VLAN tag is retained as is and the VLAN tag corresponding to the outermost tag configured for the QinQ SAP (that is, the other endpoint) is added to the packet. The system does not match the VC VLAN tag received in the packet with the configured value (that is, the inner tag of the QinQ SAP). The operator must configure both ends of the service appropriately to ensure only appropriate packets enter the service.

  • When traffic is received on the dot1q SAP, the outermost tag is stripped and the VLAN tag corresponding to the outermost tag configured for the QinQ SAP is added to the packet.

  • If the packet is received on a QinQ SAP, assign an incoming packet to this service based on matching the outermost two tags in the packet header (that is, that is, the first two tags in the packet header). It strips only the outermost tag (only a single tag) on ingress. The VLAN tag corresponding to the outermost tag configured for the QinQ SAP (that is, the other endpoint) is added to the packet and it is sent out of the QinQ SAP.

Therefore, the device processes packets received with 2 or more tags using the MPLS SDP or a dot1q SAP while classifying on the QinQ SAP ingress using 2 tags.

Feature support, configuration notes and restrictions

A new svc-sap-type value qinq-inner-tag-preserve is available for configuring the service. This must be used when creating a new Epipe service if this functionality is desired (For example: epipe 10 svc-sap-type qinq-inner-tag-preserve create):

  • This service is available only in network mode.

  • Epipe service created with the parameter svc-sap-type set to qinq-inner-tag-preserve allows for only one QinQ SAP and only one SDP of vc-type vc-vlan. The system does not allow the user to use any other SAP in this new service, that is, NULL SAP, Q1. * SAP, 0.* SAP, and so on, are not allowed for configuration in this service. The SDP cannot be of vc-type vc-ether.

  • User can configure vlan-vc-tag value for the SDP, the dot1q SAP VLAN tag value and the inner tag VLAN value of a QinQ SAP to match the VLAN ID value of the inner tag specified in the Q1.Q2 SAP configured in the service (example: if the SAP is 1/1/10:Q1.Q2, then vlan-vc-tag must be set to Q2, the dot1q SAP VLAN value must be Q2, and the inner tag of another QinQ SAP must be set to Q2). If any other value, other than QinQ SAP's inner tag is configured for vlan-vc-tag or dot1q SAP VLAN value, or for the inner tag of the QinQ SAP then it is errored out by the software. If vlan-vc-tag value is not configured, it defaults to use the inner VLAN tag value. It is highly recommended that the customer configure the vlan-vc-tag value to match the VLAN ID value of the inner tag configured for the QinQ SAP, to avoid mis-configuration.

  • Existing QoS and ACL functionality for the Epipe service entities continues to be available, with the following exceptions:

    • If the packet is received with more than 2 tags, then IP match-criteria cannot be used with SAP ingress QoS classification and ACLs (both Ingress and Egress ACLs).

    • If the packet is received with more than 2 tags, then Ethertype value in the mac-criteria cannot be used with SAP ingress QoS classification and ACLs (both Ingress and Egress ACLs).

    • Dot1p bits from the outermost tag (that is, Q1 VLAN tag, if the SAP is 1/1/10:Q1.Q2) are used for SAP ingress classification. Dot1p bits of the outermost tag are marked on egress, if marking is enabled on the egress port. The Dot1p bit value of the vlan-vc-tag is not used to mark the Dot1p bits of the outermost VLAN tag, when the packets is exiting the QinQ SAP.

  • OAM tools:

    • MPLS OAM tools such as VCCV ping and VCCV trace are supported for the SDPs

    • Accounting and Statistics for the service entities (for example, SAP and SDP) are available as before

    • CFM/Y.1731 tools are supported. UP and Down MEP is supported on the SAPs and the SDPs configured in the Epipe service.

  • The following Redundancy mechanisms available in Epipe service are supported when using MPLS SDP:

    • Epipe PW redundancy

    • MC-LAG based protection for access SAPs using the new service type (along with use PW redundancy)

vlan-vc-tag value configured to match Q1.Q2 SAP innner tag

The following example shows output of a vlan-vc-tag value configured to match the inner tag specified in the Q1.Q2 SAP configured in the service.

*A:7210SAS>config>service# info
----------------------------------------------
epipe 10 svc-sap-type qinq-inner-tag-preserve customer 1 create
       sap 1/1/3:10.45 create
    exit
    spoke-sdp 111:69 vc-type vlan create
         vlan-vc-tag 45
    exit
    no shutdown
----------------------------------------------

Epipe service with QinQ SAP and dot1q SAP

The following example shows an Epipe service with QinQ SAP and dot1q SAP. In the following example, note that the dot1q SAP (1/1/4:45) VLAN value of 45 matches the inner tag VLAN value specified with QinQ SAP (1/1/3:10.45).

*A:7210>config>service# info
----------------------------------------------
epipe 10 svc-sap-type qinq-inner-tag-preserve customer 1 create
       sap 1/1/3:10.45 create
no shutdown
    exit
    sap 1/1/4:45 create
         no shutdown
    exit
    no shutdown
exit
----------------------------------------------

Epipe service with 2 QinQ SAPs

The following example shows an Epipe service with 2 QinQ SAPs. In the following sample, note that the inner tag of both QinQ SAPs matches and is set to a value of '45'.

*A:7210>config>service# info
------------------------------------------------------------------------------------
epipe 10 svc-sap-type qinq-inner-tag-preserve customer 1 create
sap 1/1/3:10.45 create
no shutdown
exit
sap 1/1/4:200.45 create
no shutdown
exit
no shutdown
exit
-----------------------------------------------------------------------------------

Epipe oper state decoupling

An Epipe service transitions to an operational state of down when only a single entity SAP or binding is active and the operation state of the mate is down or displays an equivalent state. The default behavior does not allow you to validate the connectivity and measure performance metrics. With this feature an option is provided to allow you to validate the connectivity and measure performance metrics of an Epipe service.

You can also maintain performance and continuity measurement across the customer network regardless of the connectivity between the terminating node and the customer. If the SAP between the operator and the customer enters a Oper Down state, the Epipe remains operationally up, so the results can continue to be collected uninterrupted. The operator receives applicable port or SAP alerts/alarms. This option is available only for the customer facing SAP failures. If a network facing SAP or spoke-SDP fails, the operational state of the Epipe service is set to 'Down'. That is, there is no option to hold the service in an UP state, if a network component fails.

The following functionality is supported:

  • Configuration under SAP is required to change the default behavior of the Epipe service in response to the SAP failure.

  • The user can create a SAP on a LAG where the LAG has no port members. In this case, the operator configures the ignore-oper-state on the SAP and the service remains operational. However, as there are no ports existing in the LAG member group, there is no extraction function that can be created. This feature protects against an established working configuration with full forwarding capabilities from failing to collect PM data. The user should shutdown their equipment and place the Epipe SAP in an operationally down state.

  • The SAP connecting the provider equipment to the customer is configured to hold the Epipe service status UP when the customer facing SAP enters any failed state. Only one SAP per Epipe is allowed to be configured.

  • Any failure of the network entity (network SAP or SDP-Binding) still cause the Epipe service to transition to OPER=DOWN.

  • As the service remains operationally up, all bindings should remain operationally up and should be able to receive and transmit data. The PW status represents the failed SAP in the LDP status message, but this does not prevent the data from using the PW as a transport, in or out. This is the same as LDP status messaging.

  • The SAP failure continues to trigger normal reactions, except the operational state of the service.

  • ETH-CFM PM measurement tools (DMM/SLM) can be used with the UP MEP on the failed SAP to collect performance metric. Additionally, CFM troubleshooting tools and connectivity (LBM, LTM, AIS, CCM) can be used and function as usual.

  • ETH-CFM CCM processing and fault propagation does not change. Even when a SAP fails with the hold service UP configuration, CCM sets the Interface Status TLV to ‟Down”.

  • VPLS services remain operationally UP until the final entity in the service enters a failed operational state. There are no changes to VPLS services and the change is specific to Epipe.

Pseudowire switching

Note:

The 7210 SAS platforms as described in this document can be configured as S-PE nodes.

The pseudowire switching feature provides the user with the ability to create a VLL service by cross-connecting two spoke SDPs. This feature allows the scaling of VLL and VPLS services in a large network in which the otherwise full mesh of PE devices would require thousands of Targeted LDP (T-LDP) sessions per PE node.

Services with one SAP and one spoke-SDP are created on the PE; however, the target destination of the SDP is the pseudowire switching node instead of the remote PE.

The pseudowire switching node acts in a passive role with respect to signaling of the pseudowires. It waits until one or both of the PEs sends the label mapping message before relaying it to the other PE. This is because it needs to pass the Interface Parameters of each PE to the other.

A pseudowire switching point TLV is inserted by the switching pseudowire to record its system address when relaying the label mapping message. This TLV is useful in a few situations:

  • It allows for troubleshooting of the path of the pseudowire especially if multiple pseudowire switching points exist between the two PEs.

  • It helps in loop detection of the T-LDP signaling messages where a switching point would receive back a label mapping message it had already relayed.

  • The switching point TLV is inserted in pseudowire status notification messages when they are sent end-to-end or from a pseudowire switching node toward a destination PE.

Pseudowire OAM is supported for the manual switching pseudowires and allows the pseudowire switching node to relay end-to-end pseudowire status notification messages between the two PEs. The pseudowire switching node can generate a pseudowire status and to send it to one or both of the PEs by including its system address in the pseudowire switching point TLV. This allows a PE to identify the origin of the pseudowire status notification message.

Pseudowire service switching node

In the following example, the user configures a regular Epipe VLL service PE1 and PE2. These services consist each of a SAP and a spoke SPD. However, the target destination of the SDP is actually not the remote PE but the pseudowire switching node. In addition, the user configures an Epipe VLL service on the pseudowire switching node using the two SDPs.

| PE1 (Epipe)|---sdp 2:10---| PW SW (Epipe)|---sdp 7:15---| PE2 (Epipe)|

Pseudowire switching with protection

Pseudowire switching scales VLL and VPLS services over a multi-area network by removing the need for a full mesh of targeted LDP sessions between PE nodes. The following figure shows the use of pseudowire redundancy to provide a scalable and resilient VLL service across multiple IGP areas in a provider network.

Figure 2. VLL resilience with pseudowire redundancy and switching

In the network in the preceding figure, PE nodes act as leading nodes and pseudowire switching nodes act as followers for the purpose of pseudowire signaling. A switching node needs to pass the SAP Interface Parameters of each PE to the other.T-PE1 sends a label mapping message for the Layer 2 FEC to the peer pseudowire switching node” for example, S-PE1. It includes the SAP interface parameters, such as MTU, in the label mapping message. S-PE1 checks the FEC against the local information and if a match exists, it appends the optional pseudowire switching point TLV to the FEC TLV in which it records its system address. T-PE1 then relays the label mapping message to S-PE2. S-PE2 performs similar operations and forwards a label mapping message to T-PE2. The same procedures are followed for the label mapping message in the reverse direction, for example, from T-PE2 to T-PE1. S-PE1 and S-PE2 affect the spoke-SDP cross-connect only when both directions of the pseudowire have been signaled and matched.

The pseudowire switching TLV is useful in a few situations. First, it allows for troubleshooting of the path of the pseudowire especially if multiple pseudowire switching points exist between the two T-PE nodes. Secondly, it helps in loop detection of the T-LDP signaling messages where a switching point receives back a label mapping message it already relayed. Finally, it can be inserted in pseudowire status messages when they are sent from a pseudowire switching node toward a destination PE.

Pseudowire status messages can be generated by the T-PE nodes. Pseudowire status messages received by a switching node are processed and then passed on to the next hop. An S-PE node appends the optional pseudowire switching TLV, with its system address added to it, to the FEC in the pseudowire status notification message only if it originated the message or the message was received with the TLV in it. Otherwise, it means the message was originated by a T-PE node and the S-PE should process and pass the message without changes except for the VCID value in the FEC TLV.

Pseudowire switching behavior

In the network in VLL resilience with pseudowire redundancy and switching, PE nodes act as leading nodes and pseudowire switching nodes act as followers for the purpose of pseudowire signaling. This is because a switching node needs to pass the SAP interface parameters of each PE to the other.T-PE1 sends a label mapping message for the Layer 2 FEC to the peer pseudowire switching node, for example, S-PE1. It includes the SAP interface parameters, such as MTU, in the label mapping message. S-PE1 checks the FEC against the local information and if a match exists, it appends the optional pseudowire switching point TLV to the FEC TLV in which it records its system address. T-PE1 then relays the label mapping message to S-PE2. S-PE2 performs similar operation and forwards a label mapping message to T-PE2. The same procedures are followed for the label mapping message in the reverse direction, for example, from T-PE2 to T-PE1. S-PE1 and S-PE2 affect the spoke-SDP cross-connect only when both directions of the pseudowire have been signaled and matched.

The merging of the received T-LDP status notification message and the local status for the spoke SDPs from the service manager at a PE complies with the following rules:

  • When the local status for both spokes is up, the S-PE passes any received SAP or SDP-binding generated status notification message unchanged, for example, the status notification TLV is unchanged but the VC-ID in the FEC TLV is set to value of the pseudowire segment to the next hop.

  • When the local operational status for any of the spokes is down, the S-PE always sends SDP-binding down status bits regardless if the received status bits from the remote node indicated SAP up/down or SDP-binding up/down.

Pseudowire switching TLV

The format of the pseudowire switching TLV is as follows:



    0                   1                   2                   3
    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |1|0|     pw sw TLV  (0x096D)   |     pseudowire sw TLV  Length         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |    Variable Length Value      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         Variable Length Value                 |
   |                             "                                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

  • PW sw TLV Length

    Specifies the total length of all the following pseudowire switching point TLV fields in octets.

  • Type

    Encodes how the Value field is to be interpreted.

  • Length

    Specifies the length of the Value field in octets.

  • Value

    Octet string of Length octets that encodes information to be interpreted as specified by the Type field.

Pseudowire Switching Point Sub-TLVs

The following are details specific to pseudowire switching point sub-TLVs:

  • pseudowire ID of last pseudowire segment traversed

    This sub-TLV type contains a pseudowire ID in the format of the pseudowire ID

  • pseudowire switching point description string

    An optional description string of text up to 80 characters

  • IP address of pseudowire switching point

  • The IP V4 or V6 address of the pseudowire switching point. This is an optional sub-TLV

  • MH VCCV capability indication

Static-to-dynamic pseudowire switching

When one segment of the pseudowire cross-connect at the S-PE is static while the other is signaled using T-LDP, the S-PE operates much like a T-PE from a signaling perspective and as an S-PE from a data plane perspective.

The S-PE signals a label mapping message as soon as the local configuration is complete. The control word C-bit field in the pseudowire FEC is set to the value configured on the static spoke-SDP.

When the label mapping for the egress direction is also received from the T-LDP peer, and the information in the FEC matches that of the local configuration, the static-to-dynamic cross-connection is effected.

End nodes of a static pseudowire segment can be misconfigured. In this case, an S-PE or T-PE node may be receiving packets with the wrong encapsulation, and it is possible that an invalid payload is forwarded over the pseudowire or the SAP respectively. Also, if the S-PE or T-PE node is expecting the control word in the packet encapsulation and the received packet comes with no control word but the first nibble below the label stack is 0x0001, the packet may be mistaken for a VCCV OAM packet and may be forwarded to the CPM. In that case, the CPM performs a check of the IP header fields such as version, IP header length, and checksum. If any of this fails the VCCV packet is discarded.

Pseudowire redundancy

Pseudowire redundancy provides the ability to protect a pseudowire with a preprovisioned pseudowire and to switch traffic over to the secondary standby pseudowire in case of a SAP or network failure condition. Pseudowires are redundant by the virtue of the SDP redundancy mechanism. For instance, if the SDP is an RSVP LSP and is protected by a secondary standby path, Fast-Reroute paths, or both, the pseudowire is also protected. However, there are a couple of applications in which SDP redundancy does not protect the end-to-end pseudowire path:

  • There are two different destination PE nodes for the same VLL service. The main use case is the provision of dual-homing of a CPE or access node to two PE nodes located in different POPs. The other use case is the provision of a pair of active and standby BRAS nodes, or active and standby links to the same BRAS node, to provide service resiliency to broadband service subscribers.

  • The pseudowire path is switched in the middle of the network and the 7210 SAS pseudowire switching node fails.

Pseudowire and VPLS link redundancy extends link-level resiliency for pseudowires and VPLS to protect critical network paths against physical link or node failures. These innovations enable the virtualization of redundant paths across the metro or core IP network to provide seamless and transparent fail-over for point-to-point and multi-point connections and services. When deployed with multi-chassis LAG, the path for return traffic is maintained through the pseudowire or VPLS switchover, which enables carriers to deliver ‟always on” services across their IP/MPLS networks.

VLL resilience with two destination PE nodes

The following figure shows the application of pseudowire redundancy to provide Ethernet VLL service resilience for broadband service subscribers accessing the broadband service on the service provider BRAS.

Figure 3. VLL resilience

If the Ethernet SAP on PE2 fails, PE2 notifies PE1 of the failure by either withdrawing the primary pseudowire label it advertised or by sending a pseudowire status notification with the code set to indicate a SAP defect. PE1 receives it and immediately switches its local SAP to forward over the secondary standby spoke-SDP. To avoid black holing of in-flight packets during the switching of the path, PE1 accepts packets received from PE2 on the primary pseudowire while transmitting over the backup pseudowire.

When the SAP at PE2 is restored, PE2 updates the new status of the SAP by sending a new label mapping message for the same pseudowire FEC or by sending pseudowire status notification message indicating that the SAP is back up. PE1 then starts a timer and reverts to the primary at the expiry of the timer. By default, the timer is set to 0, which means PE1 reverts immediately. A special value of the timer (infinity) means that PE1 should never revert to the primary pseudowire.

The behavior of the pseudowire redundancy feature is the same if PE1 detects or is notified of a network failure that brought the spoke-SDP operational status to DOWN. The following are the events which cause PE1 to trigger a switchover to the secondary standby pseudowire:

  1. T-LDP peer (remote PE) node withdrew the pseudowire label.

  2. T-LDP peer signaled a FEC status indicating a pseudowire failure or a remote SAP failure.

  3. T-LDP session to peer node times out.

  4. SDP binding and VLL service went down as a result of network failure condition such as the SDP to peer node going operationally down.

The Nokia routers support the ability to configure multiple secondary standby pseudowire paths. For example, PE1 uses the value of the user configurable precedence parameter associated with each spoke-SDP to select the next available pseudowire path after the failure of the current active pseudowire (whether it is the primary or one of the secondary pseudowires). The revertive operation always switches the path of the VLL back to the primary pseudowire though. There is no revertive operation between secondary paths meaning that the path of the VLL does not switch back to a secondary pseudowire of higher precedence when the latter comes back up again.

The Nokia routers support the ability for a user-initiated manual switchover of the VLL path to the primary or any of the secondary be supported to divert user traffic in case of a planned outage such as in node upgrade procedures.

Dynamic Multi-Segment Pseudowire Routing

Overview

The following sections describe the end-to-end solution with BGP PW-routing, assuming appropriate platforms are used for various functions.

Dynamic Multi-Segment Pseudowire Routing (Dynamic MS-PWs) enable a complete multi-segment pseudowire to be established, while only requiring per-pseudowire configuration on the T-PEs. No per-pseudowire configuration is required on the S-PEs. End-to-end signaling of the MS-PW is achieved using T-LDP, while multi-protocol BGP is used to advertise the T-PEs, so allowing dynamic routing of the MS-PW through the intervening network of S-PEs. Dynamic multi-segment pseudowires are described in the IETF in draft-ietf-pwe3-dynamic-ms-pw-13.txt.

The following figure shows the operation of dynamic MS-PWs.

Figure 4. Dynamic MS-PW overview

The FEC 129 AII Type 2 structure shown in the following figure is used to identify each individual pseudowire endpoint:

Figure 5. MS-PW addressing using FEC129 AII Type 2

A 4-byte global ID followed by a 4 byte prefix and a 4 byte attachment circuit ID are used to provide for hierarchical, independent allocation of addresses on a per service provider network basis. The first 8 bytes (Global ID + Prefix) may be used to identify each individual T-PE or S-PE as a loopback Layer 2 Address.

This new AII type is mapped into the MS-PW BGP NLRI (a new BGP AFI of L2VPN, and SAFI for network layer reachability information for dynamic MS-PWs. As soon as a new T- PE is configured with a local prefix address of global id:prefix, pseudowire routing proceeds to advertise this new address to all the other T- PEs and S-PEs in the network, as shown in the following figure.

Figure 6. Advertisement of PE addresses by PW routing

In step 1 a new T-PE (T-PE2) is configured with a local prefix.

Next, in steps 2-5, MP-BGP uses the NLRI for the MS-PW routing SAFI to advertise the location of the new T-PE to all the other PEs in the network. Alternatively, static routes may be configured on a per T-PE/S-PE basis to accommodate non-BGP PEs in the solution.

As a result, pseudowire routing tables for all the S-PEs and remote T-PEs are populated with the next hop to be used to reach T-PE2.

VLL services can then be established, as shown in the following figure.

Figure 7. Signaling of dynamic MS-PWs using T-LDP

In step 1 and 1' the T-PEs are configured with the local and remote endpoint information, Source AII (SAII), Target AII (TAII). On the 7210, the AIIs are locally configured for each spoke-SDP, according to the model shown in the following figure. The 7210 therefore provides for a flexible mapping of AII to SAP. That is, the values used for the AII are through local configuration, and it is the context of the spoke-SDP that binds it to a specific SAP.

Figure 8. Mapping of AII to SAP

Before T-LDP signaling starts, the two T-PEs decide on an active and passive relationship using the highest AII (comparing the configured SAII and TAII) or the configured precedence. Next, the active T-PE (in the IETF draft this is referred to as the source T-PE or ST-PE) checks the PW Routing Table to determine the next signaling hop for the configured TAII using the longest match between the TAII and the entries in the PW routing table

This signaling hop is then used to choose the T-LDP session to the chosen next-hop S-PE. Signaling proceeds through each subsequent S-PE using similar matching procedures to determine the next signaling hop. Otherwise, if a subsequent S-PE does not support dynamic MS-PW routing and therefore uses a statically configured PW segment, the signaling of individual segments follows the procedures already implemented in the PW Switching feature.

Note: BGP can install a PW AII route in the PW routing table with ECMP next-hops. However, when LDP needs to signal a PW with matching TAII, it chooses only one next-hop from the available ECMP next-hops. PW routing supports up to 4 ECMP paths for each destination.

The signaling of the forward path ends when the PE matches the TAII in the label mapping message with the SAII of a spoke-SDP bound to a local SAP. The signaling in the reverse direction can now be initiated, which follows the entries installed in the forward path. The PW Routing tables are not consulted for the reverse path. This ensures that the reverse direction of the PW follows exactly the same set of S-PEs as the forward direction.

This solution can be used in either a MAN-WAN environment or in an Inter-AS/Inter-Provider environment as shown in the following figure.

Figure 9. VLL using dynamic MS-PWs, Inter-AS scenario
Note: Data plane forwarding at the S-PEs uses pseudowire service label switching, as per the pseudowire switching feature.

Pseudowire routing

Note: The platforms as described in this document can be configured as S-PE nodes.

The following sections describe the end-to-end solution with BGP PW-routing, assuming appropriate platforms are used for various functions.

Each S-PE and T-PE has a pseudowire routing table that contains a reference to the T-LDP session to use to signal to a set of next hop S-PEs to reach a specific T-PE (or the T-PE if that is the next hop). For VLLs, this table contains aggregated AII Type 2 FECs and may be populated with routes that are learned through MP-BGP or that are statically configured.

MP-BGP is used to automatically distribute T-PE prefixes using the new MS-PW NLRI, or static routes can be used. The MS-PW NLRI is composed of a Length, an 8-byte RD, a 4-byte Global-ID, a 4-byte local prefix, and (optionally) a 4-byte AC-ID. Support for the MS-PW address family is configured in CLI under config>router>bgp>family ms-pw.

MS-PW routing parameters are configured in the config>service>pw-routing context.

To enable support for dynamic MS-PWs on a 7210 node to be used as a T-PE or S-PE, a single, globally unique, S-PE ID, known as the S-PE Address, is first configured under config>service>pw-routing on each 7210 to be used as a T-PE or S-PE. The S-PE Address has the format global-id:prefix. It is not possible to configure any local prefixes used for pseudowire routing or to configure spoke SPDs using dynamic MS-PWs at a T-PE unless an S-PE address has already been configured. The S-PE address is used as the address of a node used to populate the switching point TLV in the LDP label mapping message and the pseudowire status notification sent for faults at an S-PE.

Each T-PE is also be configured with the following parameters:

  1. Global ID

    This is a 4 byte identifier that uniquely identifies an operator or the local network.

  2. Local Prefix

    One or more local (Layer 2) prefixes (up to a maximum of 16), which are formatted in the style of a 4-octet IPv4 address. A local prefix identifies a T-PE or S-PE in the PW routing domain.

  3. For each local prefix, at least one 8-byte route distinguisher can be configured. It is also possible to configure an optional BGP community attribute.

For each local prefix, BGP then advertises each global ID/prefix tuple and unique RD and community pseudowire using the MS-PW NLRI, based on the aggregated FEC129 AII Type 2 and the Layer 2 VPN/PW routing AFI/SAFI 25/6, to each T-PE/S-PE that is a T-LDP neighbor, subject to local BGP policies.

The dynamic advertisement of each of these pseudowire routes is enabled for each prefix and RD using the advertise-bgp command.

Exporting MS-PW routes in MP-BGP

An export policy is also required to export MS-PW routes in MP-BGP. This can be done using a default policy, such as the following.

*A:lin-123>config>router>policy-options# info
----------------------------------------------
            policy-statement "ms-pw"
                default-action accept
                exit
            exit
----------------------------------------------

However, this would export all routes. A recommended choice is to enable filtering per family, as follows.

*A:lin-123>config>router>policy-options# info
----------------------------------------------
            policy-statement "to-mspw"
                entry 1
                    from
                        family ms-pw
                    exit
                    action accept
                    exit
                exit
            exit
----------------------------------------------

The following command is then added in the config>router>bgp context.

export "to-mspw"

Local preference for iBGP and BGP communities can be configured under such a policy.

Static routing

In addition to support for BGP routing, static MS-PW routes may also be configured using the config>services>pw-routing>static-route command. Each static route comprises the target T-PE Global-ID and prefix, and the IP address of the T-LDP session to the next hop S-PE or T-PE that should be used.

If a static route is set to 0, then this represents the default route. If a static route exists to a specific T-PE, then this is used in preference to any BGP route that may exist.

Explicit paths

A set of default explicit routes to a remote T-PE or S-PE prefix may be configured on a T-PE under config>services>pw-routing using the path name command. Explicit paths are used to populate the explicit route TLV used by MS-PW T-LDP signaling. Only strict (fully qualified) explicit paths are supported.

Note: It is possible to configure explicit paths independently of the configuration of BGP or static routing.

Configuring VLLs using dynamic MS-PWs

One or more spoke SDPs may be configured for distributed Epipe VLL services. Dynamic MS-PWs use FEC129 (also known as the Generalized ID FEC) with Attachment Individual Identifier (AII) Type 2 to identify the pseudowire, as opposed to FEC128 (also known as the PW ID FEC) used for traditional single segment pseudowires and for pseudowire switching. FEC129 spoke SDPs are configured under the spoke-sdp-fec command in the CLI.

FEC129 AII Type 2 uses a Source Attachment Individual Identifier (SAII) and a Target Attachment Individual Identifier (TAII) to identify the end of a pseudowire at the T-PE. The SAII identifies the local end, while the TAII identifies the remote end. The SAII and TAII are each structured as follows:

  • Global-ID

    This is a 4 byte identifier that uniquely identifies an operator or the local network.

  • Prefix

    A 4-byte prefix, which should correspond to one of the local prefixes assigned under pw-routing.

  • AC-ID

    A 4-byte identifier for this end of the pseudowire. This should be locally unique within the scope of the global-id:prefix.

Active/passive T-PE selection

Dynamic MS-PWs use single-sided signaling procedures with double-sided configuration, a fully qualified FEC must be configured at both endpoints. That is, one T-PE (the source T-PE, ST-PE) of the MS-PW initiates signaling for the MS-PW, while the other end (the terminating T-PE, TT-PE) passively waits for the label mapping message from the far-end and only responds with a label mapping message to set up the opposite direction of the MS-PW when it receives the label mapping from the ST-PE. By default, the 7210 SAS determines which T-PE is the ST-PE (the active T-PE) and which is the TT-PE (the passive T-PE) automatically, based on comparing the SAII with the TAII as unsigned integers. The T-PE with SAII>TAII assumes the active role. However, it is possible to override this behavior using the signaling {master | auto} command under the spoke-sdp-fec. If master is selected at a specific T-PE, it assumes the active role. If a T-PE is at the endpoint of a spoke-SDP that is bound to an VLL SAP and single sided auto-configuration is used (as follows), then that endpoint is always passive. Therefore, signaling master should only be used when it is known that the far end assumes a passive behavior.

Automatic endpoint configuration

Automatic endpoint configuration allows the configuration of an endpoint without specifying the TAII associated with that spoke-sdp-fec. It allows a single-sided provisioning model where an incoming label mapping message with a TAII that matches the SAII of that spoke-SDP to be automatically bound to that endpoint. This is useful in scenarios where a service provider needs to separate service configuration from the service activation phase.

Automatic endpoint configuration is supported required for Epipe VLL spoke-sdp-fec endpoints bound to a VLL SAP. It is configured using the spoke-sdp-fec>auto-config command, and excluding the TAII from the configuration. When auto-configuration is used, the node assumed passive behavior from a point of view of T-LDP signaling. Therefore, the far-end T-PE must be configured for signaling master for that spoke-sdp-fec.

Selecting a path for an MS-PW

Path selection for signaling occurs in the outbound direction (ST-PE to TT-PE) for an MS-PW. In the TT-PE to ST-PE direction, a label mapping message follows the reverse of the path already taken by the outgoing label mapping.

A node can use explicit paths, static routes, or BGP routes to select the next hop S-PE or T-PE. The order of preference used in selecting these routes is:

  1. Explicit Path

  2. Static route

  3. BGP route

To use an explicit path for an MS-PW, an explicit path must have been configured in the config>services>pw-routing>path path-name context. The user must then configure the corresponding path path-name under spoke-sdp-fec.

If an explicit path name is not configured, the TT-PE or S-PE performs a longest match lookup for a route (static if it exists, and BGP if not) to the next hop S-PE or T-PE to reach the TAII.

Pseudowire routing chooses the MS-PW path in terms of the sequence of S-PEs to use to reach a specific T-PE. It does not select the SDP to use on each hop, which is instead determined at signaling time. When a label mapping is sent for a specific pseudowire segment, an LDP SDP is used to reach the next-hop S-PE/T-PE if such an SDP exists. If not, and a RFC 3107 labeled BGP SDP is available, then that is used. Otherwise, the label mapping fails and a label release is sent.

Pseudowire templates

Dynamic MS-PWs support the use of the pseudowire template for specifying generic pseudowire parameters at the T-PE. The pseudowire template to use is configured in the spoke-sdp-fec>pw-template-bind policy-id context. Dynamic MS-PWs do not support the provisioned SDPs specified in the pseudowire template.

Pseudowire redundancy

Pseudowire redundancy is supported on dynamic MS-PWs used for VLLs. It is configured in a similar manner to pseudowire redundancy on VLLs using FEC128, whereby each spoke-sdp-fec within an endpoint is configured with a unique SAII/TAII.

The following figure shows the use of pseudowire redundancy.

Figure 10. Pseudowire redundancy

The following is a summary of the key points to consider in using pseudowire redundancy with dynamic MS-PWs:

  • Each MS-PW in the redundant set must have a unique SAII/TAII set and is signaled separately. The primary pseudowire is configured in the spoke-sdp-fec>primary context.

  • Each MS-PW in the redundant set should use a diverse path (from the point of view of the S-PEs traversed) from every other MS-PW in that set if path diversity is possible in a specific network topology. There are a number of possible ways to achieve this:

    • Configure an explicit path for each MS-PW.

    • Allow BGP routing to automatically determine diverse paths using BGP policies applied to different local prefixes assigned to the primary and standby MS-PWs.

    • Path diversity can be further provided for each primary pseudowire through the use of a BGP route distinguisher.

If the primary MS-PW fails, a fail-over to a standby MS-PW occurs, as per the normal pseudowire redundancy procedures. A configurable retry timer for the failed primary MS-PW is then started. When the timer expires, attempt to reestablish the primary MS-PW using its original path, up to a maximum number of attempts as per the retry count parameter. The T-PE may then optionally revert to the primary MS-PW on successful reestablishment.

Note that because the SDP ID is determined dynamically at signaling time, it cannot be used as a tie breaker to choose the primary MS-PW between multiple MS-PWs of the same precedence. The user should therefore explicitly configure the precedence values to determine which MS-PW is active in the final selection.

VCCV OAM for dynamic MS-PWs

The primary difference between dynamic MS-PWs and those using FEC128 is support for FEC129 AII type 2. As in PW Switching, VCCV on dynamic MS-PWs requires the use of the VCCV control word on the pseudowire. Both the vccv-ping and vccv-trace commands support dynamic MS-PWs.

VCCV-ping on dynamic MS-PWs

VCCV-ping supports the use of FEC129 AII type 2 in the target FEC stack of the ping echo request message. The FEC to use in the echo request message is derived in one of two ways: Either the user can specify only the spoke-sdp-fec-id of the MS-PW in the vccv-ping command, or the user can explicitly specify the SAII and TAII to use.

If the SAII:TAII is entered by the user in the vccv-ping command, then those values are be used for the VCCV ping echo request, but their order is be reversed before being sent so that they match the order for the downstream FEC element for an S-PE, or the locally configured SAII:TAII for a remote T-PE of that MS-PW. If SAII:TAII is entered in addition to the spoke-sdp-fec-id, the system verifies the entered values against the values stored in the context for that spoke-sdp-fec-id.

Otherwise, if the SAII:TAII to use in the target FEC stack of the VCCV ping message is not entered by the user, and if a switching point TLV was previously received in the initial label mapping message for the reverse direction of the MS-PW (with respect to the sending PE), then the SAII:TAII to use in the target FEC stack of the VCCV ping echo request message is derived by parsing that switching point TLV based on the user-specified TTL (or a TTL of 255 if none is specified). In this case, the order of the SAII:TAII in the switching point TLV is maintained for the VCCV ping echo request message.

If no pseudowire switching point TLV was received, then the SAII:TAII values to use for the VCCV ping echo request are derived from the MS-PW context, but their order is reversed before being sent so that they match the order for the downstream FEC element for an S-PE, or the locally configured SAII:TAII for a remote T-PE of that MS-PW. Note that the use of spoke-sdp-fec-id in vccv-ping is only applicable at T-PE nodes, because it is not configured for a specific MS-PW at S-PE nodes.

VCCV-trace on dynamic MS-PWs

The 7210 SAS supports the MS-PW path trace mode of operation for VCCV trace, as per pseudowire switching, but using FEC129 AII type 2. As in the case of VCCV ping, the SAII:TAII used in the VCCV echo request message sent from the T-PE or S-PE from which the VCCV trace command is executed is specified by the user or derived from the context of the MS-PW.

Note: The use of spoke-sdp-fec-id in vccv-trace is only applicable at T-PE nodes because it is not configured for a specific MS-PW at S-PE nodes.

Example dynamic MS-PW configuration

This section presents an example of how to configure Dynamic MS-PWs for a VLL service between a set of 7210 nodes. The network consists of two 7210 T-PEs and two 7210 playing the role of S-PEs, as shown in the following figure. Each 7210 peers with its neighbor using LDP and BGP.

Figure 11. Dynamic MS-PW example

The example uses BGP to route dynamic MS-PWs and T-LDP to signal them. Therefore each node must be configured to support the MS-PW address family under BGP, and BGP and LDP peerings must be established between the T-PEs/S-PEs. The appropriate BGP export policies must also be configured.

Next, pseudowire routing must be configured on each node. This includes an S-PE address for every participating node, and one or more local prefixes on the T-PEs. MS-PW paths and static routes may also be configured. When this routing and signaling infrastructure is established, spoke-SDP FECs can be configured on each of the T-PEs.

T-PE-1 configuration

config
   router
      ldp
         targeted-session
            peer 10.20.1.5
            exit
         exit
      policy-options
         begin
         policy-statement "exportMsPw"
            entry 10
               from
                  family ms-pw
               exit
               action accept
               exit
            exit
         exit
         commit
      exit
      bgp
         family ms-pw
         connect-retry 1
         min-route-advertisement 1
         export "exportMsPw" 
         rapid-withdrawal          
         group "ebgp"
            neighbor 10.20.1.5
               multihop 255
               peer-as 200
            exit
         exit
     exit
config
   service
      pw-routing
         spe-address 3:10.20.1.3
         local-prefix 3:10.20.1.3 create
         exit
         path "path1_to_F" create
            hop 1 10.20.1.5
            hop 2 10.20.1.2
            no shutdown
        exit
     exit
     epipe 1 customer 1 vpn 1 create
        description "Default epipe
             description for service id 1"
        service-mtu 1400
        service-name "XYZ Epipe 1"
        sap 2/1/1:1 create
        exit
        spoke-sdp-fec 1 fec 129 aii-type 2 create
           retry-timer 10
           retry-count 10
           saii-type2 3:10.20.1.3:1
           taii-type2 6:10.20.1.6:1
           no shutdown

T-PE-2 configuration

config
   router
      ldp
         targeted-session
            peer 10.20.1.2
            exit
         exit
         …
      policy-options
         begin
         policy-statement "exportMsPw"
            entry 10
               from
                  family ms-pw
               exit
               action accept
               exit
            exit
         exit
         commit
      exit
      
      bgp
         family ms-pw
         connect-retry 1
         min-route-advertisement 1
         export "exportMsPw" 
         rapid-withdrawal          
         group "ebgp"
            neighbor 10.20.1.2
               multihop 255
               peer-as 300
            exit
         exit
     exit
config
   service
      pw-routing
         spe-address 6:10.20.1.6
         local-prefix 6:10.20.1.6 create
         exit
         path "path1_to_F" create
            hop 1 10.20.1.2
            hop 2 10.20.1.5
            no shutdown
        exit
     exit
     epipe 1 customer 1 vpn 1 create
        description "Default epipe
             description for service id 1"
service-mtu 1400
        service-name "XYZ Epipe 1"
        sap 1/1/3:1 create
        exit
        spoke-sdp-fec 1 fec 129 aii-type 2 create
           retry-timer 10
           retry-count 10
           saii-type2 6:10.20.1.6:1
           taii-type2 3:10.20.1.3:1
           no shutdown
        exit
        no shutdown
     exit

Master-slave operation

This section describes a mechanism in which one end on a pseudowire (the ‟master”) dictates the active PW selection, which is followed by the other end of the PW (the ‟slave”). This mechanism and associated terminology is specified in RFC 6870.

7210 SAS devices support only the standby-signaling-master option. 7210 does not support the CLI command standby-signaling-slave. In the following discussion, reference to standby-signaling-slave command is only used to describe the solution. 7210 device can be used only where standby-signaling-master is used in the following example.

Master-Slave pseudowire redundancy is discussed in this section. It adds the ability for the remote peer to react to the pseudowire standby status notification, even if only one spoke-SDP terminates on the VLL endpoint on the remote peer, by blocking the transmit (Tx) direction of a VLL spoke-SDP when the far-end PE signals standby. This solution enables the blocking of the Tx direction of a VLL spoke-SDP at both master and slave endpoints when standby is signaled by the master endpoint. This approach satisfies a majority of deployments where bidirectional blocking of the forwarding on a standby spoke-SDP is required.

The following figure shows the operation of master-slave pseudowire redundancy. In this scenario, an Epipe service is provided between CE1 and CE2. CE2 is dual homed to PE2 and PE3, and therefore PE1 is dual-homed to PE2 and PE3 using Epipe spoke SDPs. The objectives of this feature is to ensure that only one pseudowire is used for forwarding in both directions by PE1, PE2 and PE3 in the absence of a native dual homing protocol between CE2 and PE2/PE3, such as MC-LAG. In normal operating conditions (the SAPs on PE2 and PE3 toward CE2 are both up and there are no defects on the ACs to CE2), PE2 and PE3 cannot choose which spoke-SDP to forward on based on the status of the AC redundancy protocol.

Figure 12. Master-slave pseudowire redundancy

Master-slave pseudowire redundancy adds the ability for the remote peer to react to the pseudowire standby status notification, even if only one spoke-SDP terminates on the VLL endpoint on the remote peer. When the CLI command standby-signaling-slave is enabled at the spoke-SDP or explicit endpoint level in PE2 and PE3, then any spoke-SDP for which the remote peer signals PW FWD Standby is blocked in the transmit direction.

This is achieved as follows. The standby-signaling-master state is activated on the VLL endpoint in PE1. In this case, a spoke-SDP is blocked in the transmit direction at this master endpoint if it is either in operDown state, or it has lower precedence than the highest precedence spoke-SDP, or the specific peer PE signals one of the following pseudowire status bits:

  • Pseudowire not forwarding (0x01)

  • SAP (ingress) receive fault (0x02)

  • SAP (egress) transmit fault (0x04)

  • SDP binding (ingress) receive fault (0x08)

  • SDP binding (egress) transmit fault (0x10)

The fact that the specific spoke-SDP is blocked is signaled to LDP peer through the pseudowire status bit (PW FWD Standby (0x20)). This prevents traffic being sent over this spoke-SDP by the remote peer, but obviously only in case that remote peer supports and reacts to pseudowire status notification. Previously, this applied only if the spoke-SDP terminates on an IES, VPRN or VPLS. However, if standby-signaling-slave is enabled at the remote VLL endpoint then the Tx direction of the spoke-SDP is also blocked, according to the rules in Operation of master-slave pseudowire redundancy with existing scenarios.

Although master-slave operation provides bidirectional blocking of a standby spoke-SDP during steady-state conditions, it is possible that the Tx directions of more than one slave endpoint can be active for transient periods during a fail-over operation. This is because of slave endpoints transitioning a spoke-SDP from standby to active receiving or processing a pseudowire preferential forwarding status message before those transitioning a spoke-SDP to standby. This transient condition is most likely when a forced switch-over is performed, or the relative preferences of the spoke SDPs is changed, or the active spoke-SDP is shutdown at the master endpoint. During this period, loops of unknown traffic may be observed. Fail-overs because of common network faults that can occur during normal operation, a failure of connectivity on the path of the spoke-SDP or the SAP, would not result in such loops in the datapath.

Operation of master-slave pseudowire redundancy with existing scenarios

This section illustrates how master-slave pseudowire redundancy could operate.

VLL resilience

The following figure shows a VLL resilience path example. A sample configuration follows.

Figure 13. VLL resilience

A revert-time value of zero (default) means that the VLL path is switched back to the primary immediately after it comes back up.

PE1 configuration
configure service epipe 1
endpoint X
exit
endpoint Y
revert-time 0
standby-signaling-master
exit
sap 1/1/1:100 endpoint X
spoke-sdp 1:100 endpoint Y 
precedence primary
spoke-sdp 2:200 endpoint Y 
precedence 1
PE2 configuration
configure service epipe 1
endpoint X
exit
sap 2/2/2:200 endpoint X
spoke-sdp 1:100 
standby-signaling-slave
PE3 configuration
configure service epipe 1
endpoint X
exit
sap 3/3/3:300 endpoint X
spoke-sdp 2:200 
standby-signaling-slave

VLL resilience for a switched PW path

Note:

The 7210 SAS platforms as described in this document can be configured as S-PE nodes.

The following figure shows a VLL resilience for a switched pseudowire path example. A sample configuration follows.

Figure 14. VLL resilience with pseudowire switching
T-PE1 configuration
configure service epipe 1
endpoint X
exit
endpoint Y
revert-time 100
standby-signaling-master
exit
sap 1/1/1:100 endpoint X
spoke-sdp 1:100 endpoint Y 
precedence primary
spoke-sdp 2:200 endpoint Y 
precedence 1
spoke-sdp 3:300 endpoint Y 
precedence 1
T-PE2 configuration
configure service epipe 1
endpoint X
exit
endpoint Y
revert-time 100
standby-signaling-slave
exit
sap 2/2/2:200 endpoint X
spoke-sdp 4:400 endpoint Y 
precedence primary
spoke-sdp 5:500 endpoint Y 
precedence 1
spoke-sdp 6:600 endpoint Y 
precedence 1
S-PE1 configuration

VC switching indicates a VC cross-connect so that the service manager does not signal the VC label mapping immediately but put this into passive mode.

configure service epipe 1 vc-switching 
spoke-sdp 1:100 
spoke-sdp 4:400

Access node resilience using MC-LAG and pseudowire redundancy

The following figure shows the use of both Multi-Chassis Link Aggregation (MC-LAG) in the access network and pseudowire redundancy in the core network to provide a resilient end-to-end VLL service to the customers.

Figure 15. Access node resilience

In this application, a new pseudowire status bit of active or standby indicates the status of the SAP in the MC-LAG instance in the 7210 SAS aggregation node. All spoke SDPs are of secondary type and there is no use of a primary pseudowire type for this mode of operation. Node A is in the active state according to its local MC-LAG instance and therefore advertises active status notification messages to both its peer pseudowire nodes, for example, nodes C and D. Node D performs the same operation. Node B is in the standby state according to the status of the SAP in its local MC-LAG instance and therefore advertises standby status notification messages to both nodes C and D. Node C performs the same operation.

7210 SAS node selects a pseudowire as the active path for forwarding packets when both the local pseudowire status and the received remote pseudowire status indicate active status. However, a 7210 SAS device in standby status according to the SAP in its local MC-LAG instance is capable of processing packets for a VLL service received over any of the pseudowires which are up. This is to avoid black holing of user traffic during transitions. The 7210 SAS standby node forwards these packets to the active node bye the Inter-Chassis Backup pseudowire (ICB pseudowire) for this VLL service. An ICB is a spoke-SDP used by a MC-LAG node to backup a MC-LAG SAP during transitions. The same ICB can also be used by the peer MC-LAG node to protect against network failures causing the active pseudowire to go down.

Note that at configuration time, the user specifies a precedence parameter for each of the pseudowires which are part of the redundancy set as described in the application. A 7210 SAS node uses this to select which pseudowire to forward packet to in case both pseudowires show active/active for the local/remote status during transitions.

Only VLL service of type Epipe is supported in this application. Also, ICB spoke-SDP can only be added to the SAP side of the VLL cross-connect if the SAP is configured on a MC-LAG instance.

VLL resilience for a switched pseudowire path

The following figures show the use of both pseudowire redundancy and pseudowire switching to provide a resilient VLL service across multiple IGP areas in a provider network.

Figure 16. VLL resilience in a provider network
Figure 17. VLL resilience with pseudowire redundancy and switching

Pseudowire switching is a method for scaling a large network of VLL or VPLS services by removing the need for a full mesh of T-LDP sessions between the PE nodes as the number of these nodes grows over time.

Like in the application in VLL resilience with two destination PR nodes, the T-PE1 node switches the path of a VLL to a secondary standby pseudowire in the case of a network side failure causing the VLL binding status to be DOWN or if T-PE2 notified it that the remote SAP went down. This application requires that pseudowire status notification messages generated by either a T-PE node or a S-PE node be processed and relayed by the S-PE nodes.

It is possible that the secondary pseudowire path terminates on the same target PE as the primary, for example, T-PE2. This provides protection against network side failures but not against a remote SAP failure. When the target destination PE for the primary and secondary pseudowires is the same, T-PE1 does not switch the VLL path onto the secondary pseudowire upon receipt of a pseudowire status notification indicating the remote SAP is down because the status notification is sent over both the primary and secondary pseudowires.

However, the status notification on the primary pseudowire may arrive earlier than the one on the secondary pseudowire because of the differential delay between the paths. This causes T-PE1 to switch the path of the VLL to the secondary standby pseudowire and remain there until the status notification is cleared. At that point in time, the VLL path is switched back to the primary pseudowire because of the revertive behavior operation. The path does not switch back to a secondary path when it becomes up even if it has a higher precedence than the currently active secondary path.

Pseudowire redundancy service models

This section describes the various MC-LAG and pseudowire redundancy scenarios as well as the algorithm used to select the active transmit object in a VLL endpoint.

The redundant VLL service model is described in the following section, Redundant VLL service model.

Redundant VLL service model

To implement pseudowire redundancy, a VLL service accommodates more than a single object on the SAP side and on the spoke-SDP side. The following figure shows the model for a redundant VLL service based on the concept of endpoints.

Figure 18. Redundant VLL endpoint objects

A VLL service supports by default two implicit endpoints managed internally by the system. Each endpoint can only have one object, a SAP or a spoke-SDP.

To add more objects, up to two (2) explicitly named endpoints may be created per VLL service. The endpoint name is locally significant to the VLL service. They are referred to as endpoint 'X' and endpoint 'Y' as shown in the preceding figure.

The information in Redundant VLL endpoint objects is merely an example and that the ‟Y” endpoint can also have a SAP and an ICB spoke-SDP. The following details the four types of endpoint objects supported and the rules used when associating them with an endpoint of a VLL service:

  • SAP

    There can only be a maximum of one SAP per VLL endpoint.

  • Primary spoke-SDP

    The VLL service always uses this pseudowire and only switches to a secondary pseudowire when it is down the VLL service switches the path to the primary pseudowire when it is back up. The user can configure a timer to delay reverting back to primary or to never revert. There can only be a maximum of one primary spoke-SDP per VLL endpoint.

  • Secondary spoke-SDP

    There can be a maximum of four secondary spoke-SDP per endpoint. The user can configure the precedence of a secondary pseudowire to indicate the order in which a secondary pseudowire is activated.

  • Inter-Chassis Backup (ICB) spoke-SDP

    Special pseudowire used for MC-LAG and pseudowire redundancy application. Forwarding between ICBs is blocked on the same node. The user has to explicitly indicate the spoke-SDP is actually an ICB at creation time. There are however a few scenarios (as follows) where the user can configure the spoke-SDP as ICB or as a regular spoke-SDP on a specific node. The CLI for those cases indicate both options.

A VLL service endpoint can only use a single active object to transmit at any specific time but can receive from all endpoint objects

An explicitly named endpoint can have a maximum of one SAP and one ICB. When a SAP is added to the endpoint, only one more object of type ICB spoke-SDP is allowed. The ICB spoke-SDP cannot be added to the endpoint if the SAP is not part of a MC-LAG instance. Conversely, a SAP which is not part of a MC-LAG instance cannot be added to an endpoint which already has an ICB spoke-SDP.

An explicitly named endpoint, which does not have a SAP object, can have a maximum of four spoke SDPs and can include any of the following:

  • a single primary spoke-SDP

  • one or many secondary spoke SDPs with precedence

  • a single ICB spoke-SDP

T-LDP status notification handling rules

Using Redundant VLL endpoint objects as a reference, the following are the rules for generating, processing, and merging T-LDP status notifications in VLL service with endpoints. Note that any allowed combination of objects as specified in Redundant VLL service model can be used on endpoints ‟X” and ‟Y”. The following sections refer to the specific combination objects in Redundant VLL endpoint objects as an example to describe the more general rules.

Processing endpoint SAP active/standby status bits

The advertised admin forwarding status of active/standby reflects the status of the local LAG SAP in MC-LAG application. If the SAP is not part of a MC-LAG instance, the forwarding status of active is always advertised.

When the SAP in endpoint ‟X” is part of a MC-LAG instance, a node must send T-LDP forwarding status bit of ‟SAP active/standby” over all ‟Y” endpoint spoke SDPs, except the ICB spoke-SDP, whenever this status changes. The status bit sent over the ICB is always zero (active by default).

When the SAP in endpoint ‟X” is not part of a MC-LAG instance, then the forwarding status sent over all ‟Y” endpoint spoke-SDPs should always be set to zero (active by default).

Processing and merging

Endpoint ‟X” is operationally up if at least one of its objects is operationally up. It is down if all its objects are operationally down.

If the SAP in endpoint ‟X” transitions locally to the down state, or received a SAP down notification by SAP-specific OAM signal, the node must send T-LDP SAP down status bits on the ‟Y” endpoint ICB spoke-SDP only. Ethernet SAP does not support SAP OAM protocol. All other SAP types cannot exist on the same endpoint as an ICB spoke-SDP because non Ethernet SAP cannot be part of a MC-LAG instance.

If the ICB spoke-SDP in endpoint ‟X” transitions locally to down state, the node must send T-LDP SDP-binding down status bits on this spoke-SDP.

If the ICB spoke-SDP in endpoint ‟X” received T-LDP SDP-binding down status bits or pseudowire not forwarding status bits, the node saves this status and takes no further action. The saved status is used for selecting the active transmit endpoint object.

If all objects in endpoint ‟X” transition locally to down state, or received a SAP down notification by remote T-LDP status bits or by SAP specific OAM signal, or received status bits of SDP-binding down, or received status bits of pseudowire not forwarding, the node must send status bits of SAP down over all ‟Y” endpoint spoke SDPs, including the ICB.

Endpoint ‟Y” is operationally up if at least one of its objects is operationally up. It is down if all its objects are operationally down.

If a spoke-SDP in endpoint ‟Y”, including the ICB spoke-SDP, transitions locally to down state, the node must send T-LDP SDP-binding down status bits on this spoke-SDP.

If a spoke-SDP in endpoint ‟Y”, including the ICB spoke-SDP, received T-LDP SAP down status bits, or received T-LDP SDP-binding down status bits, or received status bits of pseudowire not forwarding, the node saves this status and takes no further action. The saved status is used for selecting the active transmit endpoint object.

If all objects in endpoint ‟Y”, except the ICB spoke-SDP, transition locally to down state, or received T-LDP SAP down status bits, or received T-LDP SDP-binding down status bits, or received status bits of pseudowire not forwarding, the node must send status bits of SDP-binding down over the ‟X” endpoint ICB spoke-SDP only.

If all objects in endpoint ‟Y” transition locally to down state, or received T-LDP SAP down status bits, or received T-LDP SDP-binding down status bits, or received status bits of pseudowire not forwarding, the node must send status bits of SDP-binding down over the ‟X” endpoint ICB spoke-SDP, and must send a SAP down notification on the ‟X” endpoint SAP by the SAP specific OAM signal if applicable. An Ethernet SAP does not support signaling status notifications.

Epipe configuration for MPLS-TP

Note: MPLS-TP PWs are supported in Epipe service. MPLS-TP is only supported on 7210 SAS-R6 and 7210 SAS-R12.

The following subsections describe how SDPs and spoke-SDPs are used with MPLS-TP LSPs and static PWs with MPLS-TP OAM.

SDPs

An SDP used for MPLS-TP supports the configuration of an MPLS-TP identifier as the far end address, as an alternative to an IP address. IP addresses are used if IP/MPLS LSPs are used by the SDP, or MPLS-TP tunnels identified by IPv4 source or destination addresses. MPLS-TP node identifiers are used if MPLS-TP tunnels are used.

MPLS-TP options

config
    service
        sdp
            no description
            network-domain "default"
            signaling off
            far-end node-id 0.0.0.43 global-id 4294967295
            no mixed-lsp-mode
            no ldp
            no bgp-tunnel
            lsp "unnumberedLSP"
            no vlan-vc-etype
            no pbb-etype
            no path-mtu
            no adv-mtu-override
            keep-alive
                shutdown
                hello-time 10
                hold-down-time 10
                max-drop-count 3
                timeout 5
                no message-length
            exit
            no metric
            no collect-stats
            no accounting-policy
            binding
                no port
            exit
            no shutdown
----------------------------------------------
*A:7210SAS>config>service>sdp#

The far-end node-id ip-address global-id global-id command is used to associate an SDP far end with an MPLS-TP tunnel whose far end address is an MPLS-TP node ID. If the SDP is associated with an RSVP-TE LSP, then the far-end must be a routable IPv4 address.

The system accepts the node-id being entered as either 4-octet IP address format <a.b.c.d> or unsigned integer format.

The SDP far-end refers to an MPLS-TP node-id or global-id only if:

  • delivery type is MPLS

  • signaling is off

  • keep-alive is disabled

  • mixed-lsp-mode is disabled

  • adv-mtu-override is disabled

An LSP is allowed to be configured only if the far-end info matches the LSP far-end info (whether MPLS-TP or RSVP):

  • Only one LSP is allowed if the far-end is an MPLS-TP node-id or global-id.

  • MPLS-TP or RSVP-TE LSPs are supported. However, note that LDP and BGP LSPs are not blocked in CLI.

Signaling TLDP or BGP is blocked if:

  • far-end node-id/global-id configured

  • control-channel-status enabled on any spoke (or mate vc-switched spoke)

  • PW-path-id configured on any spoke (or mate vc-switched spoke)

The following commands are blocked if a far-end node-id or global-id is configured:

  • class-forwarding

  • tunnel-far-end

  • mixed-lsp-mode

  • keep-alive

  • ldp-tunnel or bgp-tunnel

  • adv-mtu-override

VLL spoke-SDP configuration

7210 SAS-R6 and 7210 SAS-R12 can be S-PE or T-PE and 7210 SAS-T can only be a T-PE. MPLS-TP OAM related commands are applicable to spoke SDPs configured under all services supported by MPLS-TP pseudowires. All commands and functions that are applicable to spoke SDPs in the current implementation are supported, except for those that explicitly depend on an LDP session on the SDP or stated as follows. Likewise, all existing functions on a specific service SAP are supported if the spoke-sdp that it is matched to is MPLS-TP.

The following describes how to configure MPLS-TP on an Epipe VLL. However, similar configuration applies to other VLL types.

A spoke-SDP bound to an SDP with the mpls-tp keyword cannot be enabled unless the ingress label, the egress label, the control word, and the pw-path-id are configured.

VLL spoke-SDP configuration

*7210SAS>config>service>epipe# info 
----------------------------------------------
            sap 1/1/10:1.111 create
            exit
            spoke-sdp 1:111 create
               [no] hash-label  ingress
                    vc-label 2111
                exit
                egress
                    vc-label 2111
                exit
                control-word
                pw-path-id
                        agi 0:111
                        saii-type2 4294967295:0.0.0.42:111
                        taii-type2 4294967295:0.0.0.43:111
                exit
                no shutdown
            exit
            no shutdown
----------------------------------------------
*7210SAS>config>service>epipe# 

The pw-path-id context is used to configure the end-to-end identifiers for a MS-PW. These may not coincide with those for the local node if the configuration is at an S-PE. The saii and taii are consistent with the source and destination of a label mapping message for a signaled PW.

The control-channel-status command enables static PW status signaling. This is valid for any spoke-SDP where signaling none is configured on the SDP (for example, where T-LDP signaling is not in use). The refresh timer is specified in seconds, from 10-65535, with a default of 0 (off). This value can only be changed if control-channel-status is shutdown. Commands that rely on PW status signaling are allowed if control-channel-status is configured for a spoke-SDP bound to an SDP with signaling off, but the system uses control channel status signaling instead of T-LDP status signaling. The ability to configure control channel status signaling on a specific spoke-SDP is determined by the credit-based algorithm described as follows. Control-channel-status for a particular PW only counts against the credit based algorithm if it is in a no shutdown state and has a non-zero refresh timer.

Note: A shutdown of a service results in the static PW status bits for the corresponding PW being set.

The spoke-SDP is held down unless the pw-path-id is complete.

The system accepts the node ID of the pw-path-id saii or taii being entered as either a 4-octet IP address format <a.b.c.d> or an unsigned integer format.

The control word must be enabled to use MPLS-TP on a spoke-SDP.

The pw-path-id only configurable if all of the following is true:

  • network mode D

  • SDP signaling is off

  • control word enabled (control-word is disabled by default)

  • service type Epipe or VPLS

  • mate SDP signaling is off for VC-switched services

  • an MPLS-TP node ID/global ID is configured under the config>router>mpls>mpls-tp context. This is required for OAM to provide a reply address.

In the VC switching case, if configured on a mate spoke-SDP, then the TAII of the spoke-SDP must match the SAII of its mate, and SAII of spoke-SDP has to match the TAII of its mate.

A control-channel-status no shutdown is allowed only if all of the following is true:

  • Network-mode D

  • SDP signaling is off

  • Control-ord enabled (control-word by default is disabled)

  • the service type is Epipe or VPLS interface

  • Mate SDP signaling is off (in VC-switched services)

  • PW status signaling is enabled (as follows)

  • PW path ID is configured for this spoke

The hash-label option is only configurable if SDP far-end is not node-id or global-id.

The control channel status request mechanism is enabled when the request-timer timer parameter is non-zero. When enabled, this overrides the normal RFC-compliant refresh timer behavior. The refresh timer value in the status packet defined in RFC 6478 is always set to zero.

The refresh-timer in the sending node is taken from the request-timer. The two mechanisms are not compatible with each other. One node sends a request timer while the other is configured for refresh timer. In a specific node, the request timer can only be configured with both acknowledgment and refresh timers disabled.

When configured, the following procedures are used instead of the RFC 6478 procedures when a PW status changes.

The following commands are used to configure control channel status requests.

[no] control-channel-status
[no] refresh-timer <value> //0,10-65535, default:0
[no] request-timer 
[timeout-multiplier <value>]
[no] shutdown
exit
request-timer <timer1>: 0, 10-65535, defaults: 0.
  • This parameter determines the interval at which PW status messages, including a reliable delivery TLV, with the ‟request” bit set (as follows) are sent. This cannot be enabled if refresh-timer not equal to zero (0). retry-timer : 3-60s

  • This parameter determines the timeout interval if no response to a PW status is received. This defaults to zero (0) when no retry-timer. timeout-multiplier <value> - 3-15.

  • If a requesting node does not hear back after retry-timer times multiplier, then it must assume that the peer is down. This defaults to zero (0) when no retry-timer.

Credit-based algorithm

To constrain the CPU resources consumed processing control channel status messages, the system should implement a credit-based mechanism. If a user enables control channel status on a PW[n], then a number of credits c_n are consumed from a CPM-wide pool of max_credit credits. The number of credits consumed is inversely proportional to the configured refresh timer (the first three messages at 1 second interval do not count against the credit). If the current_credit <= 0, then control channel status signaling cannot be configured on a PW (but the PW can still be configured and enabled).

The following is an example algorithm:

If refresh timer > 0, c_n = 65535 / refresh_timer

Else c_n = 0.

For n=1, current_credit[n] = max-credits – c_n

Else current_credit [n] = current_credit [n-1] – c_n

If a PE with a non-zero refresh timer configured does not receive control channel status refresh messages for 3.5 time the specified timer value, then by default it times out and assumes a PW status of zero. A proprietary optional extension to the [RFC6478] protocol should be implemented to enable a node to resolve such a stale PW status condition by requesting the status from the far end node in such cases.

VLAN range for SAPs in an Epipe service

7210 SAS VLAN ranges provide a mechanism to group a range of VLAN IDs as a single service entity. This allows the operator to provide the service treatment (forwarding, ACL, QoS, Accounting, and others) to the group of VLAN IDs as a whole.

Note: Grouping a range of VLAN IDs to a SAP is supported only for Virtual Leased Lines (VLL) Ethernet services.

VLAN range SAPs feature support and restrictions

The following information describes VLAN range SAPs feature support and restrictions:

  • The access SAPs that specify VLAN range values (using connection-profile) are allowed only in Epipe service. The system allows only one range SAP in an Epipe service. Any attempt to configure more than one range SAP in an Epipe service fails. Range SAP can be configured only on access ports.

  • In network mode, the dot1q range sap is allowed to be configured in a service with svc-sap-type set to any.

  • The access SAPs using VLAN range values are allowed only for dot1q encapsulation port or LAG. A connection profile is used to specify either range of VLAN IDs or individual VLANs to be grouped together in a single SAP.

  • A ‟connection profile” is used to specify either range of VLAN IDs or individual VLANs to be grouped together in a single SAP.

  • Multiple ‟connection-profile” can be used per port or Lag as long as the VLAN value specified by each of them does not overlap. The number of VLAN ranges available per port/LAG is limited. The available number must be shared among all the SAPs on the port/LAG.

  • ‟Connection-profile”, associated with a SAP cannot be modified. To modify a connection profile, it must be removed from all SAPs that are using it.

Processing behavior for SAPs using VLAN ranges in network mode

The access SAPs that specifies VLAN range values (using connection-profile) is allowed only in an Epipe service. The system allows only one range SAP in an Epipe service. Any attempt to configure more than one range SAP in an Epipe service fails. Range SAP can be configured only on access ports. The other endpoint in the Epipe service has to be a Q.* access SAP or a spoke-sdp (PW) in network mode.

The Spoke-SDP processing and forwarding behavior for packets received on range SAPs are listed as follows: No VLAN tags are removed/stripped on ingress of the access dot1q SAPs using VLAN range connection profile. When the other endpoint in the service is configured to be an Q1.* access SAP, 7210 adds another tag to the packet and forwards it out of that SAP. If the other endpoint in the service is configured to be a spoke-SDP whose vc-type is set to vc-ether, 7210 SAS adds the appropriate MPLS PW and LSP encapsulations and forwards it out of the SDP.

In the reverse direction, when the other endpoint is a Q1.* SAP and a packet is received on it, 7210 SAS removes the outermost VLAN tag and forwards the packet out of the access dot1q SAP using VLAN ranges. When the other endpoint is a spoke-SDP (whose vc-type is set to vc-ether), 7210 SAS removes the MPLS PW and LSP encapsulation and forwards the packet out of the access dot1q SAP using VLAN ranges. The system does not check if the VLAN in the packet matches the VLAN IDs of the dot1q access SAPs configured in the service:

  • ACL support

    Filter policies are supported on SAP ingress. For more information about ACL on range SAPs, see the 7210 SAS-Mxp, R6, R12, S, Sx, T Router Configuration Guide.

  • QoS

    For ingress classification and metering with hierarchical metering support for SAP ingress, SAP ingress classification criteria available for use with VLAN range SAPs is similar to that available for other SAPs supported in an Epipe service. Dot1p based ingress classification uses the dot1p bits in the outermost VLAN tag for matching. On access egress, dot1p received from the SDP (on a network port) from another access port is preserved.

  • The amount of hardware resources (such as CAM entries used for matching in QoS classification and ACL match, meters used in SAP ingress policy, and others.) consumed by a single range SAP is equivalent to the amount of resources consumed by a single SAP that specifies a single VLAN ID for service identification. That is, the hardware has the ability to match a range of VLAN values and therefore uses ‛X’ resources for a SAP using a VLAN range instead of X * n, where ‛n’ is the number of VLANs specified in the range and X is the amount of QoS or ACL resources needed.

  • Ingress accounting support is similar to the support available for other SAPs in an Epipe service. Count of packets or octets received from individual VLANs configured in the connection profile is not available. No support for Egress SAP statistics and accounting is available.

  • Mirroring is supported. In network mode, the use of service resiliency mechanisms such as MC-LAG and Epipe PW redundancy is supported.

VLL service considerations

This section describes various of the general service features and any special capabilities or considerations as they relate to VLL services.

SDPs

The most basic SDPs must have the following:

  • a locally unique SDP identification (ID) number

  • the system IP address of the originating and far-end routers

  • an SDP encapsulation type, MPLS

SAP encapsulations

The Epipe service is designed to carry Ethernet frame payloads, so it can provide connectivity between any two SAPs that pass Ethernet frames. The following SAP encapsulations are supported on the Epipe service:

  • Ethernet null

  • Ethernet dot1q

  • QinQ

While different encapsulation types can be used, encapsulation mismatch can occur if the encapsulation behavior is not understood by connecting devices and are unable to send and receive the expected traffic. For example, if the encapsulation type on one side of the Epipe is dot1q and the other is null, tagged traffic received on the null SAP can potentially be double tagged when it is transmitted out of the dot1q SAP.

QoS policies

Traffic Management - Traffic management of Ethernet VLLs is achieved through the application of ingress QoS policies to SAPs and access egress QoS policies applied to the port. All traffic management is forwarding-class aware and the SAP ingress QoS policy identifies the forwarding class based on the rules configured to isolate and match the traffic ingressing on the SAP. Forwarding classes are determined based on the Layer 2 (Dot1p, MAC) or Layer 3 (IP, DSCP) fields of contained packets and this association of forwarding class at the ingress determines both the queuing and the Dot1P bit setting of packets on the Ethernet VLL on the egress.

SAP ingress classification and Policing - The traffic at the SAP ingress is classified and metered according to the SLA parameters. All the traffic ingressing on the SAP is classified to a particular forwarding class. All the forwarding class is metered through and marked in-profile or put-profile based on the Meter parameters.

When applied to Epipe services, service ingress QoS policies only create the unicast defined in the policy. The multipoint are not created on the service. Note that both Layer 2 or Layer 3 criteria can be used in the QoS policies for traffic classification in a service.

Egress Network DOT1P Marking - Marking of IEEE DOT1P bits in VLAN tag is as per the FC-to-Dot1p map. For details see the default network QoS policy in the 7210 SAS-Mxp, R6, R12, S, Sx, T Quality of Service Guide. This marking is applied at the port level on access ports and access uplink ports.

Ingress Network Classification - Ingress network classification is based on the Dot1p bits in the outer VLAN tag received on the access uplink port. Dot1p-to-FC mapping is based on the network ingress QoS policy.

Filter policies

7210 SAS Epipe services can have a single filter policy associated on both ingress and egress. Both MAC and IP filter policies can be used on Epipe services.

MAC resources

Epipe services are point-to-point Layer 2 VPNs capable of carrying any Ethernet payloads. Although an Epipe is a Layer 2 service, the 7210 SAS-R6 and 7210 SAS-R12 Epipe implementation does not perform MAC learning on the service, so Epipe services do not consume any MAC hardware resources.

Configuring a VLL service with CLI

This section provides information to configure Virtual Leased Line (VLL) services using the command line interface.

Basic configurations

Common configuration tasks

This section provides a brief overview of the tasks that must be performed to configure the VLL services and provides the CLI commands:

  • Associate the service with a customer ID.

  • Define SAP parameters:

    • Optional - select ingress QoS policies (configured in the config>qos context)

    • Optional - select accounting policy (configured in the config>log context)

  • Define spoke-SDP parameters.

  • Enable the service.

Configuring VLL components

This section provides VLL configuration examples for the VLL services.

Creating an Epipe service

Use the following syntax to create an Epipe service.

config>service# 
    epipe service-id [customer customer-id] [create] [vpn vpn-id] 
    description description-string
    no shutdown

For 7210 SAS-R6 and 7210 SAS-R12 devices:

config>service#
    epipe service-id [customer customer-id] [create] [vpn vpn-id][vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}] 
    description description-string
    no shutdown
Epipe configuration

The following example shows Epipe configuration output.


A:ALA-1>config>service# info
epipe 1 customer 1 vpn 1 vc-switching create
            description "Default epipe description for service id 1"
            spoke-sdp 1:1 vc-type vlan create
                description "Description for Sdp Bind 1 for Svc ID 1"
A:ALA-1>config>service# info
Configuring Epipe SAP parameters

A default QoS policy is applied to each ingress SAP. Additional QoS policies can be configured in the config>qos context. Filter policies are configured in the config>filter context and explicitly applied to a SAP. There are no default filter policies.

config>service# epipe service-id [customer customer-id]
    sap sap-id 
    accounting-policy policy-id
    collect-stats
    description description-string
    no shutdown
    egress
        filter {ip ip-filter-name | mac mac-filter-name}
    ingress
        filter {ip ip-filter-name | mac mac-filter-name}
        qos policy-id
Local Epipe SAPs

To configure a basic local Epipe service, enter the sap sap-id command twice with different port IDs in the same service configuration.

By default, QoS policy ID 1 is applied to ingress service SAPS. Existing filter policies or other existing QoS policies can be associated with service SAPs on ingress and egress ports.

Ingress and Egress SAP parameters can be applied to local and distributed Epipe service SAPs.

SAP configurations for a local Epipe service

This example displays the SAP configurations for local Epipe service 500 on SAP 1/1/2 and SAP 1/1/3 on ALA-1.

A:ALA-1>config>service# epipe 500 customer 5 create
config>service>epipe$ description "Local epipe service
config>service>epipe# sap 1/1/2 create
config>service>epipe>sap? ingress
config>service>epipe>sap>ingress# qos 20
config>service>epipe>sap>ingress# filter ip 1
config>service>epipe>sap>ingress# exit
config>service>epipe>sap# egress
config>service>epipe# sap 1/1/3 create
config>service>epipe>sap# ingress
config>service>epipe>sap>ingress# qos 555
config>service>epipe>sap>ingress# filter ip 1
config>service>epipe>sap>ingress# exit
config>service>epipe>sap# no shutdown
config>service>epipe>sap# exit

A:ALA-1>config>service# info
----------------------------------------------
...
        epipe 500 customer 5 create
            description "Local epipe service"
            sap 1/1/2 create
                ingress
                    qos 20
                    filter ip 1
                exit
            exit
            sap 1/1/3 create
                ingress
                    qos 555
                    filter ip 1
                exit
            exit
            no shutdown
        exit

Using spoke-SDP control words

The control word command provides the option to add a control word as part of the packet encapsulation for PW types for which the control word is optional. On 7210 SAS, an option is provided to enable it for Ethernet PW (Epipe). The control word may be needed because when ECMP is enabled on the network, packets of a specific PW may be spread over multiple ECMP paths if the hashing router mistakes the PW packet payload for an IPv4 or IPv6 packet. This occurs when the first nibble following the service label corresponds to a value of 4 or 6.

The control word negotiation procedures described in Section 6.2 of RFC 4447 are not supported and therefore the service only comes up if the same C bit value is signaled in both directions. If a spoke-SDP is configured to use the control word but the node receives a label mapping message with a C-bit clear, the node releases the label with an ‟Illegal C-bit” status code per Section 6.1 of RFC 4447. As soon as the user enables control of the remote peer, the remote peer withdraws its original label and sends a label mapping with the C-bit set to 1 and the VLL service is up in both nodes.

When the control word is enabled, VCCV packets also include the VCCV control word. In that case, the VCCV CC type 1 (OAM CW) is signaled in the VCCV parameter in the FEC. If the control word is disabled on the spoke-SDP, then the Router Alert label is used. In that case, VCCV CC type 2 is signaled. Note that for a multi-segment PW (MS-PW), the CC type 1 is the only supported and therefore the control word must be enabled on the spoke-SDP to be able to use VCCV ping and VCCV trace.

Spoke-SDP control word configuration

The following example shows spoke-SDP control word configuration output.

-Dut-B>config>service>epipe# info
----------------------------------------------
description "Default epipe description for service id 2100"
sap 1/2/7:4 create
description "Default sap description for service id 2100"
exit
spoke-sdp 1:2001 create
control-word
exit
no shutdown
----------------------------------------------
*A:ALA-Dut-B>config>service>epipe#
To disable the control word on spoke-sdp 1:2001:
*A:ALA-Dut-B>config>service>epipe# info
----------------------------------------------
description "Default epipe description for service id 2100"
sap 1/2/7:4 create
description "Default sap description for service id 2100"
exit
spoke-sdp 1:2001 create
exit
no shutdown
----------------------------------------------
*A:ALA-Dut-B>config>service>epipe#

Pseudowire configuration notes

The vc-switching parameter must be specified at the time the VLL service is created.

Note: When the vc-switching parameter is specified, you are configuring an S-PE. This is a pseudowire switching point (switching from one pseudowire to another). Therefore, you cannot add a SAP to the configuration.

Error generated when adding a SAP to a pseudowire

The following example show the configuration when a SAP is added to a pseudowire. The CLI generates an error response if you attempt to create a SAP. VC switching is only needed on the pseudowire at the S-PE.

*A:ALA-701>config>service# epipe 28 customer 1 create vc-switching
*A:ALA-701>config>service>epipe$ sap 1/1/3 create
MINOR: SVCMGR #1311 SAP is not allowed under PW switching service
*A:ALA-701>config>service>epipe$

Use the following syntax to create pseudowire switching VLL services.

config>service# epipe service-id [customer customer-id][vpn vpn-id] [vc-
switching]
description description-string
spoke-sdp sdp-id:vc-id

Configuring VLL pseudowiare switching services

The following example shows command usage to configure VLL pseudowire switching services.

*A:7210SAS>config>service# info 
.............
epipe 1 customer 1 vpn 1 vc-switching create
            description "Default epipe description for service id 1"
            spoke-sdp 1:1 vc-type vlan create
                description "Description for Sdp Bind 1 for Svc ID 1"
                ingress
                    vc-label 4501
                exit
                egress
                    vc-label 4501
                exit
                control-word
                pw-path-id
                        agi 1:1
                        saii-type2 1:0.0.0.2:1
                        taii-type2 1:0.0.0.1:1
                exit
                control-channel-status
                    refresh-timer 10  
                    no shutdown
                exit
                no shutdown
            exit
            spoke-sdp 1001:1 vc-type vlan create
                description "Description for Sdp Bind 1001 for Svc ID 1"
                ingress
                    vc-label 5501
                exit
                egress
                    vc-label 5501
                exit
                control-word
                pw-path-id
                        agi 1:1
                        saii-type2 1:0.0.0.1:1
                        taii-type2 1:0.0.0.2:1
                exit
                control-channel-status
                    refresh-timer 10
                    no shutdown
                exit
                no shutdown
            exit
            no shutdown
        exit
----------------------------------------------
*A:7210SAS>config>service#

S-PE1 configuration

Note: Note that specifying the vc-switching parameter enables a VC cross-connect so the service manager does not signal the VC label mapping immediately but puts this into passive mode.

The following example shows configuration output for S-PE1.

*A:ALA-S-PE1>config>service>epipe# info
----------------------------------------------
...
spoke-sdp 2:200 create
exit
spoke-sdp 3:300 create
exit
no shutdown
----------------------------------------------
*A:ALA-S-PE1>config>service>epipe#

S-PE2 configuration

Note: Note that specifying the vc-switching parameter enables a VC cross-connect so the service manager does not signal the VC label mapping immediately but puts this into passive mode.

The following example shows configuration output for S-PE2.

*A:ALA-S-PE2>config>service>epipe# info
----------------------------------------------
...
spoke-sdp 2:200 create
exit
spoke-sdp 3:300 create
exit
no shutdown
----------------------------------------------
*A:ALA-S-PE2>config>service>epipe#

Configuring VLL resilience

The following figure shows an example to create VLL resilience.

Note: The zero revert-time value means that the VLL path switches back to the primary immediately after it comes back up.
Figure 19. VLL resilience

PE1 configuration output

The following example shows configuration output on PE1.

*A:ALA-48>config>service>epipe# info
----------------------------------------------
            endpoint "x" create
            exit
            endpoint "y" create
            exit
            spoke-sdp 1:100 endpoint "y" create
                precedence primary
            exit
            spoke-sdp 2:200 endpoint "y" create
                precedence 1
            exit
            no shutdown
----------------------------------------------
*A:ALA-48>config>service>epipe#

Configuring VLL resilience for a switched pseudowire path

The following figure shows an example to create VLL resilience with pseudowire switching.

Figure 20. VLL resilience with pseudowire switching

T-PE1 configuration output

The following example shows configuration output on TPE1.

*A:ALA-48>config>service>epipe# info
----------------------------------------------
            endpoint "x" create
            exit
            endpoint "y" create
            exit
            sap 1/1/1:100 endpoint "x" create
            exit
            spoke-sdp 1:100 endpoint "y" create
                precedence primary
            exit
            spoke-sdp 2:200 endpoint "y" create
                precedence 1
            exit
            spoke-sdp 3:300 endpoint "y" create
                precedence 1
            exit
            no shutdown
----------------------------------------------
*A:ALA-48>config>service>epipe#

T-PE2 configuration output

The following example shows configuration output on TPE2.

*A:ALA-49>config>service>epipe# info
----------------------------------------------
            endpoint "x" create
            exit
            endpoint "y" create
                revert-time 100
            exit
            spoke-sdp 4:400 endpoint "y" create
                precedence primary
            exit
            spoke-sdp 5:500 endpoint "y" create
                precedence 1
            exit
            spoke-sdp 6:600 endpoint "y" create
                precedence 1
            exit
            no shutdown
----------------------------------------------
*A:ALA-49>config>service>epipe#

S-PE1 configuration output

The following example shows configuration output on S-PE1.

*A:ALA-50>config>service>epipe# info
----------------------------------------------
...
            spoke-sdp 1:100 create
            exit
            spoke-sdp 4:400 create
            exit
            no shutdown
----------------------------------------------
*A:ALA-49>config>service>epipe#

Service management tasks

This section describes the Epipe service management tasks.

Modifying Epipe service parameters

Adding an accounting policy to an existing SAP

The following example shows adding an accounting policy to an existing SAP.

config>service# epipe 2
config>service>epipe# sap
config>service>epipe>sap# accounting-policy 14
config>service>epipe>sap# exit
SAP configuration output

The following example shows SAP configuration output.

ALA-1>config>service# info
----------------------------------------------
epipe 2 customer 6 vpn 2 create
            description "Distributed Epipe service to east coast"
            sap 1/1/3:21 create
accounting-policy 14
            exit
            no shutdown
        exit
----------------------------------------------
ALA-1>config>service#

Disabling an Epipe service

Use the following syntax to shut down an Epipe service without deleting the service parameters.

config>service# epipe service-id 
    shutdown
Disabling an Epipe service
config>service# epipe 2
config>service>epipe# shutdown
config>service>epipe# exit

Re-enabling an Epipe service

Use the following syntax to re-enable an Epipe service that was shut down.

config>service# epipe service-id 
    no shutdown
Re-enabling an Epipe service
config>service# epipe 2
config>service>epipe# no shutdown
config>service>epipe# exit

Deleting an Epipe service

Perform the following steps before deleting an Epipe service:

  1. Shut down the SAP.

  2. Delete the SAP.

  3. Shut down the service.

Use the following syntax to delete an Epipe service.

config>service
    [no] epipe service-id 
    shutdown
    [no] sap sap-id 
        shutdown
Deleting an Epipe service
config>service# epipe 2
config>service>epipe# sap
config>service>epipe>sap# shutdown
config>service>epipe>sap# exit
config>service>epipe# no sap
config>service>epipe# epipe 2
config>service>epipe# shutdown
config>service>epipe# exit
config>service# no epipe 2

VLL services command reference

Command hierarchies

Epipe service configuration commands

Epipe global commands in network mode
config
    - service
        - [no] epipe service-id [customer customer-id] [create] [vpn vpn-id] [vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}]
        - no epipe service-id
            - description description-string
            - no description
            - [no] endpoint endpoint-name [create]
                - active-hold-delay active-endpoint-delay
                - no active-hold-delay
                - revert-time [revert-time | infinite]
                - no revert-time
                - standby-signaling-master
                - [no] standby-signaling-master
            - sap sap-id [create]
            - no sap sap-id 
            - service-mtu octetsno service-mtu
            - [no] service-mtu-check[no] shutdown
            - spoke-sdp sdp-id[:vc-id] [vc-type {ether | vlan}] [create] [no-endpoint]
            - spoke-sdp sdp-id[:vc-id] [vc-type {ether | vlan}] [create] endpoint 
            - no spoke-sdp sdp-id[:vc-id]
            - spoke-sdp-fec spoke-sdp-fec-id [fec fec-type] [aii-type aii-type] [create]
            - spoke-sdp-fec spoke-sdp-fec-id no-endpoint
            - spoke-sdp-fec spoke-sdp-fec-id [fec fec-type] [aii-type aii-type] [create] endpoint name [icb]
            - no spoke-sdp-fec spoke-sdp-fec-id
Epipe SAP configuration commands
config
    - service
        - [no] epipe service-id [customer customer-id] [create] [vpn vpn-id] [vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}]
        - no epipe service-id
            - sap sap-id [no-endpoint] [create]
            - sap sap-id [endpoint endpoint-name] [create]
            - no sap sap-id 
                - accounting-policy acct-policy-id
                - no accounting-policy acct-policy-id
                - [no] collect-stats
                - description description-string
                - no description
                - eth-cfm
                    - [no] ais-enable
                    - [no] mep mep-id domain md-index association ma-index [direction {up | down}] primary-vlan-enable
                        - [no] ais-enable
                            - [no] client-meg-level [[level [level ...]]
                            - [no] interval {1 | 60}
                            - [no] priority priority-value
                        - [no] ccm-enable 
                        - [no] ccm-ltm-priority priority
                        - [no] description
                        - [no] eth-test-enable
                            - [no] test-pattern {all-zeros | all-ones} [crc-enable]
                        - [no] fault-propagation-enable {use-if-tlv | suspendccm}
                        - [no] mac-address mac-address
                        - [no] one-way-delay-threshold seconds
                    - mip [mac mac address]
                    - mip default-mac
                    - no mip
                    - mep
                        - [no] ccm-enable
                        - ccm-ltm-priority priority
                        - no ccm-ltm-priority
                        - [no] eth-test-enable
                            - test-pattern {all-zeros | all-ones} [crc-enable]
                            - no test-pattern
                        - low-priority-defect {allDef | macRemErrXcon | remErrXcon | errXcon | xcon | noXcon}
                        - mac-address mac-address
                        - no mac-address
                        - [no] shutdown
                - ethernet
                    - [no] llf
                - [no] ignore-oper-down
                - [no] shutdown
Epipe SAP meter override commands
config
    - service
        - [no] epipe service-id [customer customer-id] [create] [vpn vpn-id] [vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}]
        - no epipe service-id
            - no sap sap-id 
                - ingress 
                    - meter-override
                        - meter meter-id [create]
                        - no meter meter-id
                            - adaptation-rule [pir adaptation-rule] [cir adaptation-rule]
                            -  cbs size [kbits | bytes | kbytes] 
                            - no cbs
                            - mbs size [kbits | bytes | kbytes]
                            - no mbs
                            - mode mode
                            - no mode
                            - rate cir cir-rate [pir pir-rate]
                            - no rate
Epipe spoke-SDP configuration commands
config
    - service
        - [no] epipe service-id [customer customer-id] [create] [vpn vpn-id] [vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}]
        - no epipe service-id
            - spoke-sdp sdp-id[:vc-id] [vc-type {ether | vlan}] [create] [no-endpoint]
            - spoke-sdp sdp-id[:vc-id] [vc-type {ether | vlan}] [create]  endpoint
            - no spoke-sdp sdp-id[:vc-id]
                - accounting-policy acct-policy-id
                - no accounting-policy
                - [no] collect-stats
                - [no] control-word
                - control-channel-status
                    - acknowledgment
                    - no acknowledgment
                    - refresh-timer seconds
                    - no refresh-timer
                    - request-timer request-timer request-timer-secs retry-timer retry-timer-secs timeout-multiplier multiplier
                - [no] description
                - [no] egress
                    - [no] vc-label egress-vc-label
                - eth-cfm
                    - [no] ais-enable
                    - [no] mep mep-id domain md-index association ma-index [direction {up | down}]
                        - [no] ais-enable
                            - [no] client-meg-level [[level [level ...]]
                            - [no] interval {1 | 60}
                            - [no] priority priority-value
                        - [no] ccm-enable 
                        - [no] ccm-ltm-priority priority
                        - [no] description
                        - [no] eth-test-enable
                            - [no] test-pattern {all-zeros | all-ones} [crc-enable]
                        - [no] fault-propagation-enable {use-if-tlv | suspendccm}
                        - low-priority-defect {allDef | macRemErrXcon | remErrXcon | errXcon | xcon | noXcon}
                        - [no] mac-address mac-address
                        - [no] one-way-delay-threshold seconds
                        - [no] shutdown
                    - mip [mac mac address]
                    - mip default-mac
                    - no mip
                - [no] force-vlan-vc-forwarding
                - hash-label
                - hash-label [signal-capability]
                - no hash-label
                - [no] ingress
                    - [no] vc-label egress-vc-label
                - precedence [precedence-value| primary]
                - no precedence
                - [no] pw-path-id
                    - agi attachment-group-identifier
                    - no agi
                    - no saii-type2
                    - saii-type2 global-id:node-id:ac-id
                    - no taii-type2
                    - taii-type2 global-id:node-id:ac-id
                - no pw-status-signaling
                - pw-status-signaling
                - [no] shutdown
                - vlan-vc-tag vlan-id
                - no vlan-vc-tag [vlan-id]
            - spoke-sdp-fec spoke-sdp-fec-id [fec fec-type] [aii-type aii-type] [create]
            - spoke-sdp-fec spoke-sdp-fec-id no-endpoint
            - spoke-sdp-fec spoke-sdp-fec-id [fec fec-type] [aii-type aii-type] [create] endpoint name [icb]
            - no spoke-sdp-fec spoke-sdp-fec-id
                - [no] auto-config
                - path name
                - no path
                - precedence prec-value
                - precedence primary
                - no precedence
                - pw-template-bind policy-id
                - no pw-template-bind
                - retry-count retry-count
                - no retry-count
                - retry-timer retry-timer
                - no retry-timer
                - saii-type2 global-id:prefix:ac-id
                - no saii-type2
                - [no] shutdown
                - signaling signaling
                - [no] standby-signaling-slave
                - taii-type2 global-id:prefix:ac-id
                - no taii-type2
Epipe SAP filter and QoS configuration commands
config
    - service
        - [no] epipe service-id [customer customer-id] [create] [vpn vpn-id] [vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}]
        - no epipe service-id
            - no sap sap-id 
                - egress 
                    - agg-rate-limit [cir cir-rate] [pir pir-rate]
                    - no agg-rate-limit
                    - aggregate-meter-rate rate-in-kbps [burst burst-in-kbits] [enable-stats] 
                    - no aggregate-meter-rate
                    - filter [ip ip-filter-id]
                    - filter  [ipv6 ipv6 -filter-id] 
                    - filter [mac mac-filter-id] (app
                    - no filter [ip ip-filter-id] [ ipv6 ipv6 -filter-id] [mac mac-filter-id]
                    - qos policy-id 
                    - no qos
                - ingress 
                    - aggregate-meter-rate rate-in-kbps [burst burst-in-kbits] 
                    - no aggregate-meter-rate
                    - filter [ip ip-filter-id]
                    - filter [ ipv6 ipv6-filter-id] 
                    - filter [mac mac-filter-id]
                    - no filter [ip ip-filter-id] [ ipv6 ipv6-filter-id] [mac mac-filter-id]
                    - qos policy-id [enable-table-classification] 
                    - no qos

Clear commands

clear
    - service
        - id service-id
        - statistics
            -  id service-id
            - counters
            - sap sap-id {all | counters | stp| l2pt}

Debug commands

debug
    - service
        - id service-id
            - sap sap-id
            - event-type {arp | config-change | oper-status-change} 
            - sdp sdp-id:vc-id 

Command descriptions

Configuration commands

Generic commands
shutdown
Syntax

[no] shutdown

Context

config>service>epipe

config>service>epipe>sap

config>service>epipe>sap>eth-cfm>mep

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command administratively disables an entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics.

The operational state of the entity is disabled as well as the operational state of any entities contained within. Many objects must be shut down before they may be deleted.

Services are created in the administratively down (shutdown) state. When a no shutdown command is entered, the service becomes administratively up and then tries to enter the operationally up state.

The no form of this command places the entity into an administratively enabled state.

description
Syntax

description description-string

no description

Context

config>service>epipe

config>service>epipe>sap

config>service>epipe>spoke-sdp

config>connection-profile

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command creates a text description stored in the configuration file for a configuration context. The description command associates a text string with a configuration context to identify the content in the configuration file.

The no form of this command removes the string from the configuration.

Parameters
string

Specifies the description character string. Allowed values are any string up to 80 characters composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.

eth-cfm
Syntax

eth-cfm

Context

config>service>vpls

config>service>vpls>mesh-sdp

config>service>vpls>spoke-sdp

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context configure ETH-CFM parameters.

mep
Syntax

mep mep-id domain md-index association ma-index [direction {up | down}] primary-vlan-enable

no mep mep-id domain md-index association ma-index

Context

config>service>epipe>sap>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the Maintenance Endpoint (MEP).

The no form of this command reverts to the default values.

For more information about ETH-CFM support for different services, see the 7210 SAS-Mxp, R6, R12, S, Sx, T OAM and Diagnostics Guide.

Parameters
mep-id

Specifies the MEP identifier.

Values

1 to 8191

md-index

Specifies the maintenance domain (MD) index value.

Values

1 to 4294967295

ma-index

Specifies the MA index value.

Values

1 to 4294967295

direction up | down

Indicates the direction in which the MEP faces on the bridge port. Direction is not supported when a MEP is created directly under the vpls>eth-cfm context (vMEP).

down — Keyword that sends ETH-CFM messages away from the MAC relay entity.

up — Keyword that sends ETH-CFM messages toward the MAC relay entity.

primary-vlan-enable

Provides a method for linking with the primary VLAN configured under the bridge-identifier for the MA. This is only allowed if the mhf-creation method is static. MIPs cannot be changed from or to primary VLAN functions without first being deleted.

This must be configured as part of the creation step and can be changed only by deleting the MEP and recreating it. Primary VLANs are supported only under Ethernet SAPs.

VLL global commands
epipe
Syntax

epipe service-id [customer customer-id] [create] [vpn vpn-id] [vc-switching] [svc-sap-type {any | qinq-inner-tag-preserve}]

no epipe service-id

Context

config>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures a point-to-point Epipe service instance. An Epipe connects two endpoints, defined as Service Access Points (SAPs). In a local service, the SAPs can be defined in one 7210 SAS node, and in a distributed service, the SAPs can be defined on two different 7210 SAS nodes.

Note:

  • 7210 SAS platforms as described in this document support local SAP-to-SAP service.

  • 7210 SAS platforms as described in this document support both local and distributed services.

MAC learning and filtering are not supported on an Epipe service.

When a service is created, the customer keyword and customer-id parameter must be specified to associate the service with a customer. The customer-idmust already exist, having been created using the customer command in the service context. When a service has been created with a customer association, it is not possible to edit the customer association. The service must be deleted and recreated with a new customer association.

When a service is created, the use of the customer customer-id command is optional for navigating into the service configuration context. Edit a service with the incorrect customer-id value specified results in an error.

By default, no Epipe services exist until they are explicitly created with this command.

The no form of this command deletes the Epipe service instance with the specified service-id. The service cannot be deleted until the service has been shut down and all instances of SAPs, mesh SDPs, or spoke SDPs have been deleted from the service.

Parameters
service-id

Specifies the unique service identification number or string identifying the service in the service domain. This ID must be unique to this service and may not be used for any other service of any type. The service-id must be the same number used for every 7210 SAS on which this service is defined.

Values

service-id: 1 to 2147483647 svc-name: 64 characters maximum

customer customer-id

Specifies the customer ID number to be associated with the service. This parameter is required on service creation and is optional for service editing or deletion.

Values

1 to 2147483647

vpn vpn-id

Specifies the VPN ID number, which allows you to identify virtual private networks (VPNs). If this parameter is not specified, the VPN ID uses the same number as the service ID.

Values

1 to 2147483647

Default

null (0)

vc-switching

Specifies whether pseudowire switching signaling is used for the spoke-SDPs configured in the service.

svc-sap-type

Specifies the type of service and allowed SAPs in the service.

Values

any — Specifies that, for network mode, all supported SAPs are allowed in the service. See QinQ SAP configuration restrictions for 7210 SAS in network mode only for information about restrictions related to QinQ SAPs.

qinq-inner-tag-preserve — Specifies that an Epipe service processes and forwards packets received with 3 or more tags on a QinQ SAP. See Support for processing of packets received with more than 2 tags on a QinQ SAP in Epipe service (only on 7210 SAS devices configured in network mode) for more information about available support and restrictions.

create

Keyword used to create the service instance. The create keyword requirement can be enabled or disabled in the environment>create context.

endpoint
Syntax

[no] endpoint endpoint-name [create]

Context

config>service>epipe

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures a service endpoint.

Parameters
endpoint-name

Specifies an endpoint name.

create

Mandatory keyword to create a service endpoint name.

active-hold-delay
Syntax

active-hold-delay active-hold-delay

no active-hold-delay

Context

config>service>epipe>endpoint

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies that the node delays sending the change in the T-LDP status bits for the VLL endpoint when the MC-LAG transitions the LAG subgroup that hosts the SAP for this VLL endpoint from active to standby or when any object in the endpoint. For example, SAP, ICB, or regular spoke-SDP, transitions from up to down operational state.

By default, when the MC-LAG transitioned the LAG subgroup that hosts the SAP for this VLL endpoint from active to standby, the node immediately sends new T-LDP status bits indicating the new value of "standby" over the spoke SDPs that are on the mate-endpoint of the VLL. The same applies when an object in the endpoint changes an operational state from up to down.

A value of zero means that when the MC-LAG transitioned the LAG subgroup which hosts the SAP for this VLL endpoint from active to standby, the node sends immediately new T-LDP status bits indicating the new value of standby over the spoke SDPs which are on the mate-endpoint of the VLL. The same applies when any object in the endpoint changes an operational state from up to down.

There is no delay applied to the VLL endpoint status bit advertisement when the MC-LAG transitions the LAG subgroup that hosts the SAP from "standby" to "active" or when an object in the endpoint transitions to an operationally up state.

Default

0

Parameters
active-hold-delay

Specifies the active hold delay in 100s of milliseconds.

Values

0 to 60

revert-time
Syntax

revert-time [revert-time | infinite]

no revert-time

Context

config>service>epipe>endpoint

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the time to wait before reverting back to the primary spoke-SDP defined on this service endpoint, after having failed over to a backup spoke-SDP.

Parameters
revert-time

Specifies the time, in seconds, to wait before reverting to the primary SDP.

Values

0 to 600

infinite

Keyword that causes the endpoint to be non-revertive.

standby-signaling-master
Syntax

[no] standby-signaling-master

Context

config>service>vll>endpoint

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

When this command is enabled, the pseudowire standby bit (value 0x00000020) is sent to T-LDP peer for each spoke SDP of the endpoint that is selected as a standby.

This command cannot be used with a VLL mate SAP created on an MC-LAG or ICB. This command and the vc-switching parameter are mutually exclusive.

Default

no standby-signaling-master

service-mtu
Syntax

service-mtu octets

no service-mtu

Context

config>service>epipe

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the service payload (Maximum Transmission Unit – MTU), in bytes, for the service. This MTU value overrides the service-type default MTU. The service MTU defines the payload capabilities of the service. It is used by the system to validate the SAP and the SDP binding operational state within the service.

The service MTU and a SAP service delineation encapsulation overhead (that is, 4 bytes for a dot1q tag) is used to derive the required MTU of the physical port or channel on which the SAP was created. If the required payload is larger than the port or channel MTU, the SAP is placed in an inoperative state. If the required MTU is equal to or less than the port or channel MTU, the SAP can transition to the operative state.

If a service MTU, port or channel MTU, or path MTU is dynamically or administratively modified, all associated SAP and SDP binding operational states are automatically reevaluated.

To disable service MTU check, execute the command no service-mtu-check. Disabling service MTU check allows the packets to pass to the egress if the packet length is less than or equal to the MTU configured on the port.

The no form of this command reverts to the default value.

Default

VPLS: 1514

Parameters
octets

Specifies the size of the MTU in octets, expressed as a decimal integer. The following table lists MTU values for specific VC types.

Table 1. MTU values for VC types
VC-type Example service MTU Advertised MTU

Ethernet

1514

1500

Ethernet (with preserved dot1q)

1518

1504

VPLS

1514

1500

VPLS (with preserved dot1q)

1518

1504

VLAN (dot1p transparent to MTU value)

1514

1500

VLAN (QinQ with preserved bottom Qtag)

1518

1504

Values

1 to 9194

service-mtu-check
Syntax

[no] service-mtu-check

Context

config>service>epipe

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Disabling service MTU check allows the packets to pass to the egress if the packet length is less than or equal to the MTU configured on the port. The length of the packet sent from a SAP is limited only by the access port MTU. In case of a pseudowire, the length of a packet is limited by the network port MTU (including the MPLS encapsulation).

The no form of this command disables the service MTU check.

Note:

If TLDP is used for signaling, the configured value for service-mtu is used during pseudowire set up.

Default

enabled

VLL SAP commands
sap
Syntax

sap sap-id [no-endpoint] [create]

sap sap-id endpoint endpoint-name [create]

no sap sap-id

Context

config>service>epipe

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command creates a SAP within a service. A SAP is a combination of port and encapsulation parameters that identify the SAP on the interface and within the service. Each SAP must be unique.

All SAPs must be explicitly created. If no SAPs are created within a service or on an IP interface, a SAP does not exist on that object.

Enter an existing SAP without the create keyword to edit SAP parameters.

For ports in network mode, multiple SAPs on the same port can belong to the same service.

If a port is shut down, all SAPs on that port become operationally down. When a service is shut down, SAPs for the service are not displayed as operationally down, although all traffic traversing the service is discarded.

The operational state of a SAP is relative to the operational state of the port on which the SAP is defined.

The following encapsulations are supported:

  • Ethernet access SAPs support null, dot1q

  • Ethernet access-uplink SAPs support only QinQ encapsulation.

The no form of this command deletes the SAP with the specified port. When a SAP is deleted, all configuration parameters for the SAP are also deleted.

Special Cases
Default SAPs

A default SAP has the following format: port-id:*. This type of SAP is supported only on Ethernet MDAs, and its creation is allowed only in the scope of Layer 2 services (Epipe and VPLS).

Parameters
sap-id

Specifies the physical port identifier portion of the SAP. See Common CLI command descriptions for command syntax.

endpoint

Keyword that adds a SAP endpoint association.

no endpoint

Keyword that removes the association of a SAP with an explicit endpoint name.

create

Keyword used to create a SAP instance. The create keyword requirement can be enabled or disabled in the environment>create context.

tod-suite
Syntax

tod-suite tod-suite-name

no tod-suite

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command applies a time-based policy (filter or QoS policy) to the service SAP. The suite name must already exist in the config>cron context.

Default

no tod-suite

Parameters
tod-suite-name

Specifies a collection of policies (ACLs, QoS) including time-ranges that define the full or partial behavior of a SAP. The suite can be applied to more than one SAP.

accounting-policy
Syntax

accounting-policy acct-policy-id

no accounting-policy

Context

config>service>epipe>sap

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command creates the accounting policy context that can be applied to a SAP or spoke-SDP.

An accounting policy must be defined before it can be associated with a SAP or spoke-SDP. If the policy-id does not exist, an error message is generated.

A maximum of one accounting policy can be associated with a SAP or spoke-SDP at one time. Accounting policies are configured in the config>log context.

The no form of this command removes the accounting policy association from the SAP or spoke-SDP, and the accounting policy reverts to the default.

Parameters
acct-policy-id

Specifies the accounting policy-id, as configured in the config>log>accounting-policy context.

Values

1 to 99

collect-stats
Syntax

[no] collect-stats

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables accounting and statistical data collection for either the SAP, network port, or IP interface. When applying accounting policies, by default the data is collected in the appropriate records and written to the designated billing file.

When the no collect-stats command is issued, the statistics are still accumulated by the cards. However, the CPU does not obtain the results and write them to the billing file. If a subsequent collect-stats command is issued, the counters written to the billing file include all the traffic while the no collect-stats command was in effect.

Default

no collect-stats

ethernet
Syntax

ethernet

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures Ethernet properties in this SAP.

llf
Syntax

[no] llf

Context

config>service>epipe>sap>ethernet

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables Link Loss Forwarding (LLF) on an Ethernet port. It provides an end-to-end OAM fault notification for Ethernet VLL service.

LLF on an Ethernet port brings down the port when there is a local fault on the pseudowire or service, or a remote fault on the SAP or pseudowire, signaled with label withdrawal or TLDP status bits. LLF stops signaling when the fault disappears.

The Ethernet port must be configured for null encapsulation.

The no form of this command disables LLF.

ignore-oper-down
Syntax

[no] ignore-oper-down

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This optional command configures a specific SAP to ignore the transition of the operational state to down when a SAP fails. Only a single SAP in an Epipe may use this option.

Default

no ignore-oper-down

mip
Syntax

mip [mac mac-address]

mip default-mac

no mip

Context

config>service>epipe>sap>eth-cfm

config>service>epipe>spoke-sdp>eth-cfm

config>service>vpls>sap>eth-cfm

config>service>vpls>spoke-sdp>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables Maintenance Intermediate Points (MIPs) to be created if mhf-creation for the MA is configured using the default option.

The no form of this command deletes the MIP.

Default

no mip

Parameters
mac-address

Specifies the MAC address of the MIP.

Values

6-byte mac-address in the form of xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx of the MIP. The MAC must be unicast. Using the all zeros address is equivalent to the no form of this command.

default-mac

Keyword to change the MAC back to the default MAC without having to delete the MIP and reconfigure it.

Service filter and QoS policy commands
egress
Syntax

egress

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context configure egress SAP parameters.

agg-rate-limit
Syntax

agg-rate-limit [cir cir-rate] [pir pir-rate]

no agg-rate-limit

Context

config>service>epipe>sap>egress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command defines a maximum total rate for all egress queues on a service SAP.

The SAP aggregate rate can be used only if SAP based-scheduling mode is configured at the port level. It is not supported in FC-based scheduling mode.

When configured in SAP-based scheduling mode, the egress port scheduler distributes the available bandwidth to all the SAPs configured on the port, up to the configured aggregate rate for the SAP.

The no form of this command removes the aggregate rate limit from the SAP.

Parameters
cir-rate

Specifies the CIR in kilobits per second. This parameter is supported only on the 7210 SAS-R6 and 7210 SAS-R12.

Values

0 to 10000000

pir-rate

Specifies the PIR in kilobits per second. This parameter is supported only on the 7210 SAS-R6 and 7210 SAS-R12.

Values

1 to 10000000, max

aggregate-meter-rate
Syntax

aggregate-meter-rate rate-in-kbps [burst burst-in-kbits] [enable-stats]

no aggregate-meter-rate

Context

config>service>epipe>sap>egress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command associates a set of two counters to count total forwarded packets and octets and total dropped packets and octets. When enabled, the amount of resources required increases by twice the amount of resources taken up when counter is not used. If the enable-stats keyword is specified during the creation of the meter, the counter is allocated by the software, if available. To free up the counter and relinquish its use, use the no aggregate-meter-rate command, and then recreate the meter using the aggregate-meter-rate command.

If egress Frame-based accounting is used, the SAP egress aggregate meter rate accounts for the Ethernet frame overhead. The system accounts for 12 bytes of IFG and 8 bytes of start delimiter. Frame-based counting does not affect the count of octets maintained by the counter, if in use.

Note:

  • Before enabling this command for a SAP, resources must be allocated to this feature from the egress internal TCAM resource pool using the configure system resource-profile egress-internal-tcam egress-sap-aggregate-meter command. See the 7210 SAS-Mxp, R6, R12, S, Sx, T Basic System Configuration Guide for more information.

  • The egress aggregate meter is not FC aware. The forward and drop decisions are made based on the order the packets are sent out of the SAP by the egress port scheduler.

The no form of this command removes the egress aggregate policer from use.

Default

no aggregate-meter-rate

Parameters
rate-in-kbps

Specifies the rate in kilobits per second.

Values

1 to 100000000 | max

Default

max

burst-in-kbits

Specifies the burst size for the policer in kilobits. The burst size cannot be configured without configuring the rate.

Values

4 to 2146959 | default

Default

512

enable-stats

Specifies that the counter is allocated by the software, if available.

filter
Syntax

filter [ip ip-filter-id]

filter [ipv6 ipv6-filter-id]

filter [mac mac-filter-id]

no filter [ip ip-filter-id]

no filter [ipv6 ipv6-filter-id]

no filter [mac mac-filter-id]

Context

config>service>epipe>sap>egress

config>service>epipe>sap>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command associates an IP filter policy with an ingress or egress SAP or IP interface.

Filter policies control the forwarding and dropping of packets based on IP matching criteria. Only one filter can be applied to a SAP at a time.

The filter command is used to associate a filter policy with a specified filter-id with an ingress or egress SAP. The filter-id must already be defined before the filter command is executed. If the filter policy does not exist, the operation fails and an error message is returned.

IP filters apply only to RFC 2427-routed IP packets. Frames that do not contain IP packets are not subject to the filter and are always passed, even if the default action of the filter is to drop.

Note:

For filter support available on different 7210 SAS platforms, see the 7210 SAS-Mxp, R6, R12, S, Sx, T Router Configuration Guide.

The no form of this command removes any configured filter ID association with the SAP or IP interface. The filter ID is not removed from the system.

Special Cases
Epipe

Both MAC and IP filters are supported on an Epipe service SAP.

Parameters
ip ip-filter-id

Specifies the IP filter policy. The filter ID must already exist within the created IP filters.

Values

1 to 65535

ipv6 ipv6-filter-id

Specifies the IPv6 filter policy. The filter ID must already exist within the created IPv6 filters.

Values

1 to 65535

mac mac-filter-id

Specifies the MAC filter policy. The specified filter ID must already exist within the created MAC filters. The filter policy must already exist within the created MAC filters.

Values

1 to 65535

qos
Syntax

qos policy-id

qos policy-id [enable-table-classification]

no qos

Context

config>service>epipe>sap>egress

config>service>epipe>sap>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command associates a Quality of Service (QoS) policy with an ingress SAP.

QoS ingress policies are important for the enforcement of SLA agreements. The policy ID must be defined before associating the policy with a SAP or IP interface. If the policy-id does not exist, an error is returned.

The qos command is used to associate both ingress and egress QoS policies. The qos command allows ingress policies to be associated only on SAP or IP interface ingress, and allows egress policies only on SAP or IP interface egress. Attempts to associate a QoS policy of the wrong type returns an error.

Only one ingress QoS policy can be associated with a SAP or IP interface at one time. Attempts to associate a second policy of same or different type replaces the earlier one with the new policy.

On the 7210 SAS-R6 and 7210 SAS-R12 (ingress), using the enable-table-classification keyword enables the use of IP DSCP tables to assign FC and profile on a per-SAP ingress basis. The match-criteria configured from the service ingress policy, which require CAM resources, are ignored. Only meters from the service ingress policy are used (and the meters still require CAM resources). The IP DSCP classification policy configured in the SAP ingress policy is used to assign FC and profile. The default FC is assigned from the SAP ingress policy.

By default, if no specific QoS policy is associated with the SAP for ingress or egress, the default QoS policy is used.

The no form of this command removes the QoS policy association from the SAP, and the QoS policy reverts to the default.

Parameters
policy-id

Specifies the ingress or egress policy ID to associate with SAP on ingress or egress. The policy ID must already exist.

Values

1 to 65535

enable-table-classification

Keyword to enable the use of table-based classification instead of CAM-based classification at SAP ingress. The FC and profile are taken from the IP DSCP classification policy configured in the ingress policy, along with the meters from the SAP ingress policy. Match-criteria entries in the SAP ingress policy are ignored.

ingress
Syntax

ingress

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context configure ingress SAP QoS policies.

If no SAP ingress QoS policy is defined, the system default SAP ingress QoS policy is used for ingress processing.

aggregate-meter-rate
Syntax

aggregate-meter-rate rate-in-kbps [burst burst-in-kbits]

no aggregate-meter-rate

Context

config>service>epipe>sap>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the SAP ingress aggregate policer. The rate of the SAP ingress aggregate policer must be specified by the user. The user can optionally specify the burst size for the SAP aggregate policer. The aggregate policer monitors the ingress traffic on different FCs and determines the final disposition of the packet. The packet is either forwarded to an identified profile or dropped.

Note:

The sum of CIR of the individual FCs configured under the SAP cannot exceed the PIR rate configured for the SAP. The 7210 SAS software does not block this configuration, however it is not recommended.

When the SAP aggregate policer is configured, per FC policer can be configured only in ‟trtcm2” mode (RFC 4115).

Note:

The meter modes ‟srtcm” and ‟trtcm1” are used in the absence of an aggregate meter.

The SAP ingress meter counters increment the packet or octet counts based on the final disposition of the packet.

If ingress Frame-based accounting is used, the SAP aggregate meter rate accounts for the Ethernet frame overhead. The system accounts for 12 bytes of IFG and 8 bytes of start delimiter.

The no form of this command removes the aggregate policer from use.

Default

no aggregate-meter-rate

Parameters
rate-in-kbps

Specifies the rate in kilobits per second.

Values

1 to 100000000 | max

Default

max

burst-in-kbits

Specifies the burst size for the policer in kilobits. The burst size cannot be configured without configuring the rate.

Values

4 to 2146959 | default

Default

512

The following table lists the final disposition of the packet based on the operating rate of the per-FC policer and the per-SAP aggregate policer or meter.

Table 2. Final disposition of packet
Per FC meter operating rate Per FC assigned color SAP aggregate meter operating rate SAP aggregate meter color Final packet color

Within CIR

Green

Within PIR

Green

Green or

In-profile

Within CIR1

Green

Above PIR

Red

Green or

In-profile

Above CIR, Within PIR

Yellow

Within PIR

Green

Yellow or

Out-of-Profile

Above CIR, Within PIR

Yellow

Above PIR

Red

Red or

Dropped

Above PIR

Red

Within PIR

Green

Red or

Dropped

Above PIR

Red

Above PIR

Red

Red or

Dropped

1 This row is not recommended for use. For more information, see the Note in the aggregate-meter-rate command description.
meter-override
Syntax

[no] meter-override

Context

config>service>epipe>sap>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures specific overrides to one or more meters created on the SAP through the sap-ingress QoS policies.

The no form of this command is used to remove existing meter overrides.

Default

no meter-override

meter
Syntax

meter meter-id [create]

no meter meter-id

Context

config>service>epipe>sap>ingress>meter-override

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables the context for specific overrides to a specific meter created on the SAP through a SAP ingress QoS policies.

The no form of this command is used to remove existing overrides for the specified meter-id.

Parameters
meter-id

This parameter is required when executing the meter command within the meter-overrides context. The specified meter-id must exist within the SAP ingress QoS policy applied to the SAP. If the meter is not currently used by any forwarding class or forwarding type mappings, the meter does not exist on the SAP. This does not preclude creating an override context for the meter-id.

create

Keyword that is required when a meter meter-id override node is being created and the system is configured to expect explicit confirmation that a new object is being created. When the system is not configured to expect explicit confirmation, the create keyword is not required.

adaptation-rule
Syntax

adaptation-rule [pir adaptation-rule] [cir adaptation-rule]

no adaptation-rule

Context

config>service>epipe>sap>ingress>meter-override>meter

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the override of specific attributes of the specified meter adaptation rule parameters. The adaptation rule controls the method used by the system to derive the operational CIR and PIR settings when the meter is provisioned in hardware. For the CIR and PIR parameters individually, the system attempts to find the best operational rate, depending on the defined constraint.

The no form of this command removes explicitly defined constraints used to derive the operational CIR and PIR created by the application of the policy. When a specific adaptation-rule is removed, the default constraints for rate and cir apply.

Default

no adaptation-rule

Parameters
pir

Specifies the constraints enforced when adapting the PIR rate defined within the meter-override meter meter-id command. The pir parameter requires a qualifier that defines the constraint used when deriving the operational PIR for the queue. When the meter-override command is not specified, the default applies.

When the meter mode in use is ‟trtcm2,” this parameter is interpreted as EIR value. See the description and relevant notes for meter modes in the 7210 SAS-Mxp, R6, R12, S, Sx, T Quality of Service Guide for more information.

cir

Specifies the constraints enforced when adapting the CIR rate defined within the meter-override meter meter-id command. The cir parameter requires a qualifier that defines the constraint used when deriving the operational CIR for the queue. When the cir parameter is not specified, the default constraint applies.

adaptation-rule

Specifies the criteria to use to compute the operational CIR and PIR values for this meter, while maintaining a minimum offset.

Values

max — The max, min, and closest options are mutually exclusive. When max (maximum) is defined, the operational PIR for the meter will be equal to or less than the administrative rate specified using the meter-override command.

min — The min, max and closest options are mutually exclusive. When min (minimum) is defined, the operational PIR for the queue will be equal to or greater than the administrative rate specified using the meter-override command.

closest — The closest, min and max options are mutually exclusive. When closest is defined, the operational PIR for the meter will be the rate closest to the rate specified using the meter-override command.

cbs
Syntax

cbs size [kbits | bytes | kbytes]

no cbs

Context

config>service>epipe>sap>ingress>meter-override>meter

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the override of the default CBS for the meter. The committed burst size parameter specifies the maximum burst size that can be transmitted by the source while still complying with the CIR. If the transmitted burst is lower than the CBS value, the packets are marked as in-profile by the meter to indicate that the traffic is complying with meter configured parameters.

The no form of this command reverts to the default value.

Default

32 kbits

Parameters
size

Specifies the value in kilobits, bytes, or kilobytes.

Values

kbits: 4 to 2146959 | default

bytes: 512 to 274810752

kbytes: 1 to 268369

mbs
Syntax

mbs size [kbits | bytes | kbytes]

no mbs

Context

config>service>epipe>sap>ingress>meter-override>meter

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures a mechanism to override the default MBS for the meter. The maximum burst size parameter specifies the maximum burst size that can be transmitted by the source while still complying with the CIR. If the transmitted burst is lower than the MBS value then the packets are marked as in-profile by the meter to indicate that the traffic is complying with meter configured parameters.

The no form of this command reverts to the default value.

Default

512kbits

Parameters
size

Specifies the value in kilobits, bytes, or kilobytes.

Values

kbits: 4 to 2146959 | default

bytes: 512 to 274810752

kbytes: 1 to 268369

mode
Syntax

mode mode

no mode

Context

config>service>epipe>sap>ingress>meter-override>meter

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command overrides the SAP ingress QoS policy configured mode parameters for the specified meter-id.

The no form of this command restores the policy defined metering and profiling mode to a meter.

Parameters
mode

Specifies the rate mode of the meter-override.

Values

trtcm1, trtcm2, srtcm

rate
Syntax

rate cir cir-rate [pir pir-rate]

no rate

Context

config>service>epipe>sap>ingress>meter-override>meter

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command overrides the SAP ingress QoS policy configured rate parameters for the specified meter-id.

The max default specifies the amount of bandwidth in kilobits per second (thousand bits per second). The max value is mutually exclusive to the pir-rate value.

The no form of this command reverts the policy defined metering and profiling rate to a meter.

Default

max

Parameters
pir-rate

Defines the administrative PIR rate, in kilobits, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed. Fractional values are not allowed and must be specified as a positive integer.

When the meter mode is set to ‟trtcm2” the PIR value is interpreted as the EIR value. See the 7210 SAS-Mxp, R6, R12, S, Sx, T Quality of Service Guide for more information.

The actual PIR rate is dependent on the queue adaptation-rule parameters and the hardware where the queue is provisioned.

Values

0 to 20000000 | max

Default

max

cir-rate

Specifies to override the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be specified as a positive integer.

Values

0 to 20000000 | max

Default

0

statistics
Syntax

statistics

Context

config>service>epipe>sap

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context configure the counters associated with SAP ingress and egress.

ingress
Syntax

ingress

Context

config>service>epipe>sap>statistics

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context configure the ingress SAP statistics counter.

counter-mode
Syntax

counter-mode {in-out-profile-count| forward-drop-count}

Context

config>service>epipe>sap>statistics>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command sets the counter mode for the counters associated with SAP ingress meters (also known as policers). A pair of counters is available with each meter. These counters count different events based on the counter mode value.

Note:
  • The counter mode can be changed if an accounting policy is associated with a SAP. If the counter mode is changed, the counters associated with the meter are reset and the counts are cleared. If an accounting policy is in use when the counter mode is changed, a new record is written into the current accounting file.

  • The configuration information is not saved across a reboot.

Perform the following sequence of commands on the specified SAP to ensure the correct statistics are collected when the counter-mode is changed.

  1. Execute the config service epipe sap no collect-stats command to disable the writing of accounting records for the SAP.

  2. Change the counter-mode to the required option by executing the config service epipe sap counter-mode {in-out-profile-count | forward-drop-count} command.

  3. Execute the config service epipe sap collect-stats command to enable the writing of accounting records for the SAP.

The no form of this command reverts to the default value.

Default

in-out-profile-count

Parameters
forward-drop-count

When this parameter is specified, one counter counts the forwarded packets and octets received on ingress of a SAP and another counts the dropped packets. The forwarded count is the sum of in-profile and out-of-profile packets/octets received on SAP ingress. The dropped count is count of packets/octets dropped by the policer. A packet is determined to be in-profile or out-of-profile based on the meter rate parameters configured. A packet is dropped by the policer if it exceeds the configured PIR rate. The in-profile count and out-of-profile count is not individually available when operating in this mode.

in-out-profile-count

When this parameter is specifies, one counter counts the total in-profile packets and octets received on ingress of a SAP and another counts the total out-of-profile packets and octets received on ingress of a SAP. A packet is determined to be in-profile or out-of-profile based on the meter rate parameters configured. A packet is dropped by the policer if it exceeds the configured PIR rate. Dropped counts are not maintained in hardware when this mode is used. It is obtained by subtracting the sum of in-profile count and out-of-profile count from the total SAP ingress received count and displayed.

drop-count-extra-vlan-tag-pkts
Syntax

[no] drop-count-extra-vlan-tag-pkts

Context

config>service>epipe>sap>statistics>ingress

config>service>epipe>spoke-sdp>statistics>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command associates a counter, which enables the counting of extra VLAN-tag dropped packets for the SAP or spoke-SDP. A limited number of such counters are available for use.

The no form of this command removes the associated counter.

VLL SDP commands
spoke-sdp
Syntax

spoke-sdp sdp-id[:vc-id] [no-endpoint] [create]

spoke-sdp sdp-id[:vc-id] endpoint endpoint-name

no spoke-sdp sdp-id[:vc-id]

Context

config>service>epipe

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command binds a service to an existing Service Distribution Point (SDP).

The SDP has an operational state, which determines the operational state of the SDP within the service; for example, if the SDP is administratively or operationally down, the SDP for the service is down.

The SDP must already exist in the config>service>sdp context before it can be associated with an Epipe or VPL service. If the sdp sdp-id is not already configured, an error message is generated. If the sdp-id exists, a binding between the specific sdp-id and the service is created.

SDPs must be explicitly associated and bound to a service to allow far-end 7210 SAS-R6 and 7210 SAS-R12 devices to participate in the service.

The no form of this command removes the SDP binding from the service; the SDP configuration is not affected. When the SDP binding is removed, no packets are forwarded to the far-end router.

Special Cases
Epipe

At most, only one sdp-id can be bound to an Epipe service. Because an Epipe is a point-to-point service, it can have, at most, two end points. The two end points can be one SAP and one SDP or two SAPs. VC-switching VLLs are an exception. If the VLL is a ‟vc-switching” VLL, the two endpoints must both be SDPs.

Parameters
sdp-id

Specifies the SDP identifier. Allowed values are integers for existing SDPs.

Values

1 to 17407

vc-id

Specifies the virtual circuit identifier.

Values

1 to 4294967295

no endpoint

Keyword that removes the association of a spoke-SDP with an explicit endpoint name.

endpoint endpoint-name

Specifies the name of the service endpoint.

control-word
Syntax

[no] control-word

Context

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command adds a control word as part of the packet encapsulation for pseudowire types for which the control word is optional. These are Ethernet pseudowires (Epipe).

The configuration for the two directions of the pseudowire must match because the control word negotiation procedures described in Section 6.2 of RFC 4447 are not supported. The C-bit in the pseudowire FEC sent in the label mapping message is set to 1 when the control word is enabled. Otherwise, it is set to 0.

The service only comes up if the same C-bit value is signaled in both directions. If a spoke-sdp is configured to use the control word but the node receives a label mapping message with a C-bit clear, the node releases the label with the an ‟Illegal C-bit” status code, in accordance with Section 6.1 of RFC 4447. When the user also enables the control on the remote peer, the remote peer withdraws its original label and sends a label mapping with the C-bit set to 1; the VLL service then becomes up in both nodes.

control-channel-status
Syntax

[no] control-channel-status

Context

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures static pseudowire status signaling on a spoke-SDP for which signaling for its SDP is set to OFF.

A control-channel-status no shutdown is allowed only if all of the following is true:

  • SDP signaling is off

  • control word is enabled (control word by default is disabled)

  • service type is Epipe or VPLS

  • mate SDP signaling is off (in VC-switched services)

  • pw-path-id is configured for this spoke

The no form of this command removes control channel status signaling form a spoke-sdp. It can only be removed if control channel status is shutdown.

Default

no control-channel-status

acknowledgment
Syntax

[no] acknowledgment

Context

config>service>epipe>spoke-sdp>control-channel-status

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the acknowledgment of control channel status messages. By default, no acknowledgment packets are sent.

refresh-timer
Syntax

refresh-timer value

no refresh-timer

Context

config>service>epipe>spoke-sdp>control-channel-status

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the refresh timer for control channel status signaling packets. By default, no refresh packets are sent.

Default

no refresh-timer

Parameters
value

Specifies the refresh timer value.

Values

10 to 65535 seconds

Default

0 (off)

request-timer
Syntax

request-timer request-timer request-timer-secs retry-timer retry-timer-secs timeout-multiplier multiplier

Context

config>service>epipe>spoke-sdp>control-channel-status

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the control channel status request mechanism. When it is configured, control channel status request procedures are used. These augment the procedures for control channel status messaging, in accordance with RFC 6478. This command and a non-zero refresh-timer value are mutually exclusive.

Parameters
request-timer-secs

Specifies the interval at which pseudowire status messages, including a reliable delivery TLV, with the ‟request” bit set, are sent.

Values

10 to 65535 seconds

retry-timer-secs

Specifies the timeout interval if no response to a pseudowire status request is received. This parameter must be configured. A value of zero (0) disables retries.

Values

0, 3 to 60 seconds

multiplier

Specifies that, if a requesting node does not receive a valid response to a pseudowire status request within this multiplier times the retry timer, it assumes the pseudowire is down. This parameter is optional.

Values

3 to 20 seconds

force-vlan-vc-forwarding
Syntax

[no] force-vlan-vc-forwarding

Context

config>service>epipe>spoke-sdp

config>service>vpls>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command forces vc-vlan-type forwarding in the datapath for spokes that have either vc-type. This command is not allowed on vlan-vc-type SDPs.

The no version of this command reverts to the default value.

Default

disabled

hash-label
Syntax

hash-label [signal-capability]

no hash-label

Context

config>service>epipe>spoke-sdp

Platforms

7210 SAS-R6 IMMv2 and IMM-c cards and 7210 SAS-R12 IMMv2 and IMM-c cards

Description

This command configures the use of the hash label on a VLL or VPLS service bound to LDP or RSVP SDP using the autobind mode with the ldp, rsvp-te, or mpls options. When this feature is enabled, the ingress datapath is modified such that the result of the hash on the packet header is communicated to the egress datapath for use as the value of the label field of the hash label. The egress datapath appends the hash label at the bottom of the stack (BoS) and sets the S-bit to one (1).

Note:

On 7210 SAS, the hash label is not used on the local node for purpose of ECMP hashing and LAG hashing. It is available for use by LSR nodes through which the traffic flows and that are capable of using the labels for hashing.

Packets generated in CPM and that are forwarded labeled within the context of a service (for example, OAM packets) must also include a hash label at the BoS and set the S-bit accordingly.

The TTL of the hash label is set to a value of 0.

The user enables the signaling of the hash-label capability under a VLL spoke-sdp, a VPLS spoke-sdp, or mesh-sdp interface by adding the signal-capability option. In this case, the decision whether to insert the hash label on the user and control plane packets by the local PE is solely determined by the outcome of the signaling process and can override the local PE configuration. The following rules apply when the hash-label option and the signal-capability option are enabled on the local PE.

  • The 7210 SAS local PE inserts the Flow Label Interface Parameters sub-TLV with T=1 and R=1 in the PW ID FEC element in the label mapping message for that spoke-SDP or mesh SDP.

  • If the remote PE does not send the Flow Label sub-TLV in the PW ID FEC element, or sends a Flow Label sub-TLV in the PW ID FEC element with T=FALSE and R=FALSE, the local node disables the hash label capability. Therefore, the local PE node does not insert a hash label in user and control plane packets; it forwards on the spoke-SDP or mesh SDP. It also drops user and control plane packets received from the remote PE if they include a hash label. Note that the latter may be caused by a remote 7210 SAS PE that does not support the hash-label option, or that has the hash-label option enabled but does not support the signal-capability option, or does support both options but the user did not enable them because of a misconfiguration.

  • If remote PE sends Flow Label sub-TLV in the PW ID FEC element with T=TRUE and R=TRUE, the local PE enables the hash label capability. Therefore, local PE inserts a hash label in user and control plane packets it forwards on the spoke-SDP or mesh SDP. It also accepts user and control plane packets remote PE with or without a hash label.

If the hash-label option was enabled on the local configuration of the spoke-sdp or mesh-sdp at the remote PE, the pseudowire packets received by the local PE include the hash label. These packets must be dropped. The only way to solve this is to disable the signaling capability option on the local node, which results in the insertion of the hash label by both PE nodes.

If the hash-label option is not supported or was not enabled on the local configuration of the spoke-SDP or mesh SDP at the remote PE, the pseudowire received by the local PE does not have the hash label included.

The user can enable or disable the signal-capability option in CLI as needed. When doing so, the router must withdraw the label it sent to its peer and send a new label mapping message with the new value of the F bit in the flow label interface parameters sub-TLV of the PW ID FEC element.

Note:

  • This feature is supported only for VLL and VPLS services. It not supported for VPRN services. It is also not supported on multicast packets forwarded using RSVP P2MP LPS or mLDP LSP in both the base router instance and in the multicast VPN (mVPN) instance.

  • In 7x50 and possibly other vendor implementations, to allow applications where the egress LER infers the presence of the hash label implicitly from the value of the label, the Most Significant Bit (MSB) of the result of the hash is set before copying into the Hash Label. Therefore, the value of the hash label is always in the range [524,288 to 1,048,575] and does not overlap with the signaled/static LSP and signaled/static service label ranges. This also guarantees the hash label does not match a value in the reserved label range. This is not supported on 7210 SAS for service traffic (for MPLS OAM traffic the MSB bit is set). That is, 7210 SAS devices do not set the MSB bit in the hash label value for service traffic. If enabled, the user must ensure that both the ends are correctly configured to process hash labels.

The no form of this command disables the use of the hash label.

Default

no hash-label

Parameters
signal-capability

Keyword to enable the signaling and negotiation of the use of the hash label between the local and remote PE nodes.

precedence
Syntax

precedence [precedence-value | primary]

no precedence

Context

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies the precedence of the SDP binding when there are multiple SDP bindings attached to one service endpoint. The value of zero can only be assigned to one SDP bind making it the primary SDP bind. When an SDP binding goes down, the next highest precedence SDP binding begins to forward traffic.

The no form of this command reverts the value to the default.

Default

4

Parameters
precedence-value

Specifies the spoke-SDP precedence.

Values

1 to 4

primary

Specifies to make this the primary spoke-SDP.

pw-path-id
Syntax

[no] pw-path-id

Context

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures an MPLS-TP Pseudowire Path Identifier for a spoke-SDP. All elements of the PW path ID must be configured to enable a spoke-SDP with a PW path ID.

For an IES or VPRN spoke-SDP, the PW path ID is only valid for Ethernet spoke SDPs.

This command is configurable only if all the following conditions are true:

  • system is using network chassis mode D

  • SDP signaling is off

  • control-word is enabled (control-word is disabled by default)

  • the service type is Epipe or VPLS.

  • mate SDP signaling is off for VC-switched services

The no form of this command deletes the PW path ID.

Default

no pw-path-id

agi
Syntax

agi agi

no agi

Context

config>service>epipe>spoke-sdp>pw-path-id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the attachment group identifier for an MPLS-TP PW.

Parameters
agi

Specifies the attachment group identifier.

Values

0 to 4294967295

saii-type2
Syntax

saii-type2 global-id:node-id:ac-id

no saii-type2

Context

config>service>epipe>spoke-sdp>pw-path-id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the source individual attachment identifier (SAII) for an MPLS-TP spoke-sdp. If this is configured on a spoke-sdp for which vc-switching is also configured, that is, if it is at an S-PE, the values must match those of the taii-type2 of the mate spoke-sdp.

Parameters
global-id

Specifies the global ID at the source PE or T-PE for the MPLS-TP PW for a spoke-SDP.

Values

0 to 4294967295

node-id

Specifies the node ID at the source PE or T-PE for the MPLS-TP PW for a spoke-SDP.

Values

a.b.c.d or 0 to 4294967295

ac-id

Specifies the attachment circuit ID at the source PE or T-PE for the MPLS-TP PW for a spoke-SDP. If this node is the source of the PW, the AC ID must be set to a locally unique value.

Values

1 to 4294967295

taii-type2
Syntax

taii-type2 global-id:node-id:ac-id

no taii-type2

Context

config>service>epipe>spoke-sdp>pw-path-id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the source individual attachment identifier (SAII) for an MPLS-TP spoke-sdp. If this is configured on a spoke-sdp for which vc-switching is also configured, that is, it is at an S-PE, the values must match those of the taii-type2 of the mate spoke-sdp.

Parameters
global-id

Specifies the global ID at the target PE or T-PE for the MPLS-TP PW for a spoke-SDP.

Values

0 to 4294967295

node-id

Specifies the node ID at the target PE or T-PE for the MPLS-TP PW for a spoke-SDP.

Values

a.b.c.d or 0 to 4294967295

ac-id

Specifies the attachment circuit ID at the target PE or T-PE for the MPLS-TP PW for a spoke-SDP. If this node is the source of the PW, the AC ID must be set to a locally unique value.

Values

1 to 4294967295

pw-status-signaling
Syntax

[no] pw-status-signaling

Context

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables pseudowire status signaling for this spoke-SDP binding.

The no form of this command disables the status signaling.

Default

pw-status-signaling

vc-label
Syntax

[no] vc-label vc-label

Context

config>service>epipe>spoke-sdp>egress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the egress VC label.

Parameters
vc-label

Specifies a VC egress value that indicates a specific connection.

Values

16 to 1048575

vc-label
Syntax

[no] vc-label vc-label

Context

config>service>epipe>spoke-sdp>ingress

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the ingress VC label.

Parameters
vc-label

Specifies a VC ingress value that indicates a specific connection.

Values

2048 to 18431

vlan-vc-tag
Syntax

vlan-vc-tag vlan-id

no vlan-vc-tag [vlan-id]

Context

config>service>epipe>spoke-sdp

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies an explicit dot1q value used when encapsulating to the SDP far end. When signaling is enabled between the near and far end, the configured dot1q tag can be overridden by a received TLV specifying the dot1q value expected by the far end. This signaled value must be stored as the remote signaled dot1q value for the binding. The provisioned local dot1q tag must be stored as the administrative dot1q value for the binding.

When the dot1q tag is not defined, the default value of zero is stored as the administrative dot1q value. Setting the value to zero is equivalent to not specifying the value.

The no form of this command disables the command.

Default

no vlan-vc-tag

Parameters
vlan-id

Specifies a valid VLAN identifier to bind an 802.1Q VLAN tag ID.

Values

0 to 4094

spoke-sdp-fec
Syntax

spoke-sdp-fec

spoke-sdp-fec spoke-sdp-fec-id [fec fec-type] [aii-type aii-type] [create]

spoke-sdp-fec spoke-sdp-fec-id no-endpoint

spoke-sdp-fec spoke-sdp-fec-id [fec fec-type] [aii-type aii-type] [create] endpoint name [icb]

Context

config>service>epipe

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command binds a service to an existing Service Distribution Point (SDP), using a dynamic MS-PW.

A spoke-SDP is treated like the equivalent of a traditional bridge ‟port” where flooded traffic received on the spoke-SDP is replicated on all other ‟ports” (other spoke and mesh SDPs or SAPs) and not transmitted on the port it was received.

The SDP has an operational state which determines the operational state of the SDP within the service. For example, if the SDP is administratively or operationally down, the SDP for the service is down.

When using dynamic MS-PWs, the particular SDP to bind-to is automatically selected based on the Target Attachment Individual Identifier (TAII) and the path to use, specified under spoke-SDP FEC. The selected SDP terminates on the first hop S-PE of the MS-PW. Therefore, an SDP must already be defined in the config>service>sdp context that reaches the first hop 7210 SAS of the MS-PW. The 7210 SAS associates an SDP with a service. If an SDP is not already configured, an error message is generated. If the sdp-id does exist, a binding between that sdp-id and the service is created.

This command differs from the spoke-sdp command in that the spoke-sdp command creates a spoke-SDP binding that uses a PW with the PW ID FEC. However, the spoke-sdp-fec command enables PWs with other FEC types to be used. In Release 9.0, only the Generalised ID FEC (FEC129) may be specified using this command.

The no form of this command removes the SDP binding from the service. The SDP configuration is not affected; only the binding of the SDP to a service. When removed, no packets are forwarded to the far-end router.

Parameters
spoke-sdp-fec-id

Specifies an unsigned integer value identifying the spoke-SDP.

Values

1 to 4294967295

fec fec-type

Specifies an unsigned integer value for the type of the FEC used by the MS-PW.

Values

129 to 130

aii-type aii-type

Specifies an unsigned integer value for the Attachment Individual Identifier (AII) type used to identify the MS-PW endpoints.

Values

1 to 2

endpoint endpoint-name

Specifies the name of the service endpoint.

no endpoint

Keyword to add or remove a spoke-SDP association.

icb

Keyword to configure the spoke-SDP as an inter-chassis backup SDP binding.

auto-config
Syntax

[no] auto-config

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables single-sided automatic endpoint configuration of the spoke-SDP. The 7210 SAS acts as the passive T-PE for signaling this MS-PW.

Automatic Endpoint Configuration allows the configuration of a spoke-SDP endpoint without specifying the TAII associated with that spoke-SDP. It allows a single-sided provisioning model where an incoming label mapping message with a TAII that matches the SAII of that spoke-SDP to be automatically bound to that endpoint. In this mode, the far end T-PE actively initiates MS-PW signaling and sends the initial label mapping message using T-LDP, while the 7210 SAS T-PE for which auto-config is specified acts as the passive T-PE.

The auto-config command is blocked in CLI if signaling active has been enabled for this spoke-SDP. It it is only applicable to spoke SDPs configured under the Epipe, IES and VPRN interface context.

The no form of this command means that the 7210 SAS T-PE either acts as the active T-PE (if signaling active is configured) or automatically determines which 7210 SAS initiates MS-PW signaling based on the prefix values configured in the SAII and TAII of the spoke-SDP. If the SAII has the greater prefix value, the 7210 SAS initiates MS-PW signaling without waiting for a label mapping message from the far end. However, if the TAII has the greater value prefix, the 7210 SAS assumes that the far end T-PE will initiate MS-PW signaling and will wait for that label mapping message before responding with a T-LDP label mapping message for the MS-PW in the reverse direction.

Default

no auto-config

path
Syntax

path name

no path

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies the explicit path, containing a list of S-PE hops, that should be used for this spoke-SDP. The path-name should correspond to the name of an explicit path configured using the config>service>pw-routing context.

If no path is configured, each next-hop of the MS-PW used by the spoke-SDP will be chosen locally at each T-PE and S-PE.

Default

no path

Parameters
path-name

Specifies the name of the explicit path to be used, as configured in the config>service>pw-routing context.

precedence
Syntax

precedence prec-value

precedence primary

no precedence

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies the precedence of the SDP binding when there are multiple SDP bindings attached to one service endpoint. The value of zero can be assigned to only one SDP bind making it the primary SDP bind. When an SDP binding goes down, the next highest precedence SDP binding begins to forward traffic.

The no form of this command reverts to the default value.

Default

42

Parameters
precedence-value

Specifies the spoke-SDP precedence.

Values

1 to 4

primary

Keyword to make this the primary spoke-SDP.

pw-template-bind
Syntax

pw-template-bind policy-id

no pw-template-bind

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command binds the parameters included in a specific PW Template to a spoke-SDP.

The no form of this command removes the values from the configuration.

Parameters
policy-id

Specifies the existing policy ID.

Values

1 to 2147483647

retry-count
Syntax

retry-count retry-count

no retry-count

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This optional command specifies the number of attempts software should make to reestablish the spoke-SDP after it has failed. After each successful attempt, the counter is reset to zero.

When the specified number is reached, no more attempts are made, and the spoke-sdp is put into the shutdown state.

Use the no shutdown command to bring up the path after the retry limit is exceeded.

The no form of this command reverts to the default value.

Default

30

Parameters
retry-count

Specifies the maximum number of retries before putting the spoke-sdp into the shutdown state.

Values

10 to 10000

retry-timer
Syntax

retry-timer retry-timer

no retry-timer

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies a retry-timer for the spoke-SDP. This is a configurable exponential back-off timer that determines the interval between retries to reestablish a spoke-SDP if it fails, a label withdraw message is received with the status code ‟AII unreachable”.

The no form of this command reverts to the default value.

Default

30

Parameters
retry-timer

Specifies the initial retry-timer value in seconds.

Values

10 to 480

saii-type2
Syntax

saii-type2 global-id:prefix:ac-id

no saii-type2

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the source attachment individual identifier for the spoke-sdp. This is only applicable to FEC129 AII type 2.

Parameters
global-id

Specifies a global ID for this 7210 SAS T-PE. This value must correspond to one of the global_id values configured for a local-prefix in the config>service>pw-routing>local-prefix context.

Values

1 to 4294967295

prefix

Specifies the prefix, expressed as an IPv4-formatted address, on this 7210 SAS T-PE that the spoke-sdp SDP is associated with.This value must correspond to one of the prefixes configured in the config>service>pw-routing>local-prefix context.

Values

a.b.c.d or 1 to 4294967295

ac-id

Specifies an unsigned integer representing a locally unique identifier for the spoke-SDP.

Values

1 to 4294967295

signaling
Syntax

signaling signaling

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures this 7210 SAS as the active or passive T-PE for signaling this MS-PW, or to automatically select whether this T-PE is active or passive based on the prefix.

In an active role, this endpoint initiates MS-PW signaling without waiting for a T-LDP label mapping message to arrive from the far end T-PE. In a passive role, it waits for the initial label mapping message from the far end before sending a label mapping for this end of the PW. In auto mode, if the SAII has the greater prefix value, the 7210 SAS initiates MS-PW signaling without waiting for a label mapping message from the far end. However, if the TAII has the greater value prefix, the 7210 SAS assumes that the far end T-PE is initiating MS-PW signaling and waits for that label mapping message before responding with a T-LDP label mapping message for the MS-PW in the reverse direction.

The no form of this command means that the 7210 SAS T-PE automatically selects the 7210 SAS that will initiate MS-PW signaling based on the prefix values configured in the SAII and TAII of the spoke-SDP, as described previously.

Default

auto

Parameters
signaling

Specifies this 7210 SAS as the active T-PE for signaling this MS-PW.

Values

auto, master

standby-signaling-slave
Syntax

[no] standby-signaling-slave

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

When this command is enabled, the node blocks the transmit forwarding direction of a spoke-SDP based on the setting of the standby bit received from a T-LDP peer.

This command is present at the endpoint level and spoke-SDP level. If the spoke-sdp is part of an explicit-endpoint, it is not possible to change this setting at the spoke-sdp level. An existing spoke-sdp can be made part of the explicit endpoint only if the settings do not conflict. A newly created spoke-sdp, which is part of a specific explicit-endpoint, inherits this setting from the endpoint configuration. An existing spoke-sdp cannot be moved to an endpoint if the setting of standby-signaling-slave is not the same as at the endpoint level. If the standby-signaling-slave setting is changed at the endpoint level, that change is automatically populated to the member spoke-sdps.This command cannot be configured for an endpoint that is part of an MC-LAG, ICB, and MC endpoint, or for which standby-signaling-master has been enabled.

If this command is disabled, the node assumes the existing Release 5.0 mode of behavior for forwarding on the spoke-SDP.

Default

no standby-signaling-slave

taii-type2
Syntax

taii-type2 global-id:prefix:ac-id

no taii-type2

Context

config>service>epipe>spoke-sdp-fec

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command configures the target attachment individual identifier for the spoke-sdp. This is only applicable to FEC129 AII type 2.

This command is blocked in CLI if this end of the spoke-SDP is configured for single-sided auto configuration (using the auto-config command).

Parameters
global-id

Specifies the global ID of this 7210 T-PE. This value must correspond to one of the global_id values configured for a local-prefix in the config>service>pw-routing>local-prefix context.

Values

1 to 4294967295

prefix

Specifies the prefix, expressed as an IPv4-formatted address, on this 7210 T-PE that the spoke-sdp SDP is associated with.This value must correspond to one of the prefixes configured in the config>service>pw-routing>local-prefix context.

Values

a.b.c.d or 1 to 4294967295

ac-id

Specifies an unsigned integer representing a locally unique identifier for the spoke-SDP.

Values

1 to 4294967295

Connection profile commands

connection-profile
Syntax

connection-profile conn-prof-id [create]

no connection-profile conn-prof-id

Context

config

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command creates a list of VLAN values to be assigned to a dot1q SAP in an Epipe service.

A connection profile can only be assigned to a dot1q SAP that is part of an Epipe Service.

The no form of this command deletes the profile from the configuration.

Parameters
noneconn-prof-id

Specifies the profile number.

Values

1 to 8000

ethernet
Syntax

ethernet

Context

config>connprof

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context configure the VLAN ranges values.

ranges
Syntax

no ranges

ranges vlan-ranges [vlan-ranges...(upto 32 max)]

Context

config>connprof>ethernet

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command specifies the list of VLAN ranges or individual VLAN ID to be used for mapping the specific VLANs to the Epipe SAP.

The system validates that the values specified are valid VLAN IDs in the range 0 to 4094 (VLAN ID 4095 is reserved). Ranges are specified in the format ‟a-b,” the expression (a < b) should be true. Up to about 32 individual VLAN values or VLAN ranges can be specified. A maximum of 8 VLAN ranges are allowed per connection profile.

Parameters
vlan-ranges

Specifies the list of VLAN ranges or individual VLAN ID to be used for mapping the specific VLANs to the Epipe SAP.

A list of space separated values specified as either a-b or individual VLAN IDs. Both the VLAN IDs and the value used for ‟a” and ‟b” must be in the range of 0 to 4094. Additionally, value ‟a” must be less than value ‟b.”

For example:

ranges

100 to 200 5 6 4000 to 4020

ranges

4 5 6 10 11 12

ranges

250 to 350 500 to 600 1000 to 1023

Show commands

sap-using
Syntax

sap-using [sap sap-id]

sap-using interface [ip-address | ip-int-name]

sap-using [ingress] filter filter-id

sap-using [ingress] qos-policy qos-policy-id

sap-using encap-type encap-type

Context

show>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays SAP information.

If no optional parameters are specified, the command displays a summary of all defined SAPs.

The optional parameters restrict output to only SAPs matching the specified properties.

Parameters
ip-addr

Specifies the IP address of the interface for which to display matching SAPs.

Values

a.b.c.d

ip-int-name

Specifies the IP interface name for which to display matching SAPs.

ingress

Specifies matching an ingress policy.

egress

Specifies matching an egress policy.

qos-policy qos-policy-id

Specifies the ingress QoS Policy ID for which to display matching SAPs.

Values

1 to 65535

filter filter-id

Specifies the ingress or egress filter policy ID for which to display matching SAPs.

Values

1 to 65535

sap sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI command descriptions for command syntax.

encap-type encap-type

Displays the CEM encapsulation type.

Values

cem

Output

The following output is an example of SAP information, and Output fields: service SAP-using describes the output fields.

Sample output

*A:DUT-B_sasx>show>service# sap-using

===============================================================================
Service Access Points
===============================================================================
PortId                          SvcId      Ing.  Ing.    Egr.  Egr.   Adm  Opr
                                           QoS   Fltr    QoS   Fltr
-------------------------------------------------------------------------------
1/1/3:1                         1          10    none    1     none   Up   Up
1/1/3:2                         2          1     none    1     none   Up   Up
1/1/3:3                         3          1     none    1     none   Up   Up
1/1/3:4                         4          1     none    1     none   Up   Up
1/1/3:5                         5          1     none    1     none   Up   Up
1/1/3:6                         6          1     none    1     none   Up   Up
1/1/3:7                         7          1     none    1     none   Up   Up
1/1/3:8                         8          1     none    1     none   Up   Up
1/1/3:9                         9          1     none    1     none   Up   Up
1/1/3:10                        10         1     none    1     none   Up   Up
1/1/3:11                        11         1     none    1     none   Up   Up
1/1/3:12                        12         1     none    1     none   Up   Up
1/1/3:13                        13         1     none    1     none   Up   Up
1/1/3:14                        14         1     none    1     none   Up   Up
1/1/3:15                        15         1     none    1     none   Up   Up
1/1/3:16                        16         1     none    1     none   Up   Up
1/1/3:17                        17         1     none    1     none   Up   Up
1/1/3:18                        18         1     none    1     none   Up   Up
1/1/3:19                        19         1     none    1     none   Up   Up
1/1/3:20                        20         1     none    1     none   Up   Up
1/1/3:21                        21         1     none    1     none   Up   Up
1/1/3:22                        22         1     none    1     none   Up   Up
1/1/3:23                        23         1     none    1     none   Up   Up
1/1/3:24                        24         1     none    1     none   Up   Up
1/1/3:25                        25         1     none    1     none   Up   Up
1/1/3:26                        26         1     none    1     none   Up   Up
1/1/3:27                        27         1     none    1     none   Up   Up
1/1/3:28                        28         1     none    1     none   Up   Up
1/1/3:29                        29         1     none    1     none   Up   Up
1/1/3:30                        30         1     none    1     none   Up   Up
1/1/3:31                        31         1     none    1     none   Up   Up
1/1/3:32                        32         1     none    1     none   Up   Up
1/1/3:33                        33         1     none    1     none   Up   Up
1/1/3:34                        34         1     none    1     none   Up   Up
1/1/3:35                        35         1     none    1     none   Up   Up
1/1/3:36                        36         1     none    1     none   Up   Up
1/1/3:37                        37         1     none    1     none   Up   Up
1/1/3:38                        38         1     none    1     none   Up   Up
1/1/3:39                        39         1     none    1     none   Up   Up
1/1/3:40                        40         1     none    1     none   Up   Up
1/1/3:41                        41         1     none    1     none   Up   Up
1/1/3:42                        42         1     none    1     none   Up   Up
1/1/3:43                        43         1     none    1     none   Up   Up
1/1/3:44                        44         1     none    1     none   Up   Up
1/1/3:45                        45         1     none    1     none   Up   Up
1/1/3:46                        46         1     none    1     none   Up   Up
1/1/3:47                        47         1     none    1     none   Up   Up
1/1/3:48                        48         1     none    1     none   Up   Up
1/1/3:49                        49         1     none    1     none   Up   Up
1/1/3:50                        50         1     none    1     none   Up   Up
1/1/3:51                        51         1     none    1     none   Up   Up
1/1/3:52                        52         1     none    1     none   Up   Up
1/1/3:53                        53         1     none    1     none   Up   Up
1/1/3:54                        54         1     none    1     none   Up   Up
1/1/3:55                        55         1     none    1     none   Up   Up
1/1/3:56                        56         1     none    1     none   Up   Up
1/1/3:57                        57         1     none    1     none   Up   Up
1/1/3:58                        58         1     none    1     none   Up   Up
1/1/3:59                        59         1     none    1     none   Up   Up
1/1/3:60                        60         1     none    1     none   Up   Up
1/1/3:61                        61         1     none    1     none   Up   Up
1/1/3:62                        62         1     none    1     none   Up   Up
1/1/3:63                        63         1     none    1     none   Up   Up
1/1/3:64                        257        1     none    1     none   Up   Up
-------------------------------------------------------------------------------
Number of SAPs : 64
-------------------------------------------------------------------------------
===============================================================================


*A:DUT-B_sasx>show>service# sap-using sap 1/1/3:1

===============================================================================
Service Access Points Using Port 1/1/3:1
===============================================================================
PortId                          SvcId      Ing.  Ing.    Egr.  Egr.   Adm  Opr
                                           QoS   Fltr    QoS   Fltr
-------------------------------------------------------------------------------
1/1/3:1                         1          10    none    1     none   Up   Up
-------------------------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------------------------
===============================================================================
Table 3. Output fields: service SAP-using
Label Description

Port ID

The ID of the access port where the SAP is defined.

Svc ID

The service identifier.

MTU

The port MTU value.

Ing. QoS

The SAP ingress QoS policy number specified on the ingress SAP.

Ing Fltr

The MAC or IP filter policy ID applied to the ingress SAP.

Egr. QoS

The SAP egress QoS policy number specified on the egress SAP.

Egr. Fltr

The MAC or IP filter policy ID applied to the egress SAP.

Adm

The administrative state of the SAP.

Opr

The operational state of the SAP.

sdp
Syntax

sdp [sdp-id | far-end ip-address] [detail | keep-alive-history]

Context

show>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays SDP information.

If no optional parameters are specified, a summary SDP output for all SDPs is displayed.

Parameters
sdp-id

Specifies the SDP ID for which to display information.

Default

All SDPs.

Values

1 to 17407

far-end ip-address

Displays only SDPs matching with the specified far-end IP address.

Default

SDPs with any far-end IP address.

detail

Displays detailed SDP information.

Default

SDP summary output.

keep-alive-history

Displays the last fifty SDP keepalive events for the SDP.

Default

SDP summary output.

Output

The following output is an example of SDP information, and Output fields: service SDP describes the output fields.

Sample output
*A:ALA-12# show service sdp
==============================================================================
Services: Service Destination Points                                           
==============================================================================
SdpId    Adm MTU   Opr MTU   IP address       Adm  Opr         Deliver Signal  
------------------------------------------------------------------------------
10       4462      4462      10.20.1.3        Up   Dn NotReady MPLS    TLDP    
40       4462      1534      10.20.1.20       Up   Up          MPLS    TLDP    
60       4462      1514      10.20.1.21       Up   Up          MPLS TLDP    
100      4462      4462      10.0.0.2         Down Down        MPLS TLDP    
500      4462      4462      10.20.1.50       Up   Dn NotReady MPLS TLDP    
------------------------------------------------------------------------------
Number of SDPs : 5                                                            
==============================================================================
*A:ALA-12# 


*A:ALA-12# show service sdp 2 detail
===============================================================================
Service Destination Point (Sdp Id : 2) Details
===============================================================================
Sdp Id 2  -(10.10.10.104)
-------------------------------------------------------------------------------
Description           : MPLS-10.10.10.104
SDP Id               : 2
Admin Path MTU       : 0                     Oper Path MTU      : 0
Far End              : 10.10.10.104          Delivery           : MPLS
Admin State          : Up                    Oper State         : Down
Flags                : SignalingSessDown TransportTunnDown
Signaling            : TLDP                  VLAN VC Etype      : 0x8100
Last Status Change   : 02/01/2007 09:11:39   Adv. MTU Over.     : No
Last Mgmt Change     : 02/01/2007 09:11:46

KeepAlive Information :
Admin State          : Disabled              Oper State         : Disabled
Hello Time           : 10                    Hello Msg Len      : 0
Hello Timeout        : 5                     Unmatched Replies  : 0
Max Drop Count       : 3                     Hold Down Time     : 10
Tx Hello Msgs        : 0                     Rx Hello Msgs      : 0

Associated LSP LIST :
SDP Delivery Mechanism is not MPLS
===============================================================================
*A:ALA-12# 
*A:ALA-12# show service sdp 8
==============================================================================
Service Destination Point (Sdp Id : 8)
==============================================================================
SdpId    Adm MTU   Opr MTU   IP address       Adm  Opr         Deliver Signal
------------------------------------------------------------------------------
8        4462      4462      10.10.10.104     Up   Dn NotReady MPLS    TLDP
==============================================================================
*A:ALA-12# 


*A:ALA-12# show service sdp 8 detail
===============================================================================
Service Destination Point (Sdp Id : 8) Details
===============================================================================
Sdp Id 8  -(10.10.10.104)
-------------------------------------------------------------------------------
Description           : MPLS-10.10.10.104
SDP Id               : 8
Admin Path MTU       : 0                     Oper Path MTU      : 0
Far End              : 10.10.10.104          Delivery           : MPLS
Admin State          : Up                    Oper State         : Down
Flags                : SignalingSessDown TransportTunnDown
Signaling            : TLDP                  VLAN VC Etype      : 0x8100
Last Status Change   : 02/01/2007 09:11:39   Adv. MTU Over.     : No
Last Mgmt Change     : 02/01/2007 09:11:46

KeepAlive Information :
Admin State          : Disabled              Oper State         : Disabled
Hello Time           : 10                    Hello Msg Len      : 0
Hello Timeout        : 5                     Unmatched Replies  : 0
Max Drop Count       : 3                     Hold Down Time     : 10
Tx Hello Msgs        : 0                     Rx Hello Msgs      : 0

Associated LSP LIST :
Lsp Name             : to-104
Admin State          : Up                    Oper State         : Down
Time Since Last Tran*: 01d07h36m
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALA-12#
Table 4. Output fields: service SDP
Label Description

SDP Id

The SDP identifier.

Adm MTU

Specifies the configured largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Opr MTU

Specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

IP address

Specifies the IP address of the remote end of the MPLS tunnel defined by this SDP.

Adm

Admin State

Specifies the configured state of the SDP.

Opr

Oper State

Specifies the operating state of the SDP.

Deliver

Delivery

Specifies the type of delivery used by the SDP: MPLS.

Flags

Specifies all the conditions that affect the operating status of this SDP.

Signal

Signaling

Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP.

Last Status Change

Specifies the time of the most recent operating status change to this SDP.

Last Mgmt Change

Specifies the time of the most recent management-initiated change to this SDP.

Number of SDPs

Specifies the total number of SDPs displayed according to the criteria specified.

Hello Time

Specifies how often the SDP echo request messages are transmitted on this SDP.

Number of SDPs

Specifies the total number of SDPs displayed according to the criteria specified.

Hello Time

Specifies how often the SDP echo request messages are transmitted on this SDP.

Hello Msg Len

Specifies the length of the SDP echo request messages transmitted on this SDP.

Hello Timeout

Specifies the number of seconds to wait for an SDP echo response message before declaring a timeout.

Unmatched Replies

Specifies the number of SDP unmatched message replies.

Max Drop Count

Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault.

Hold Down Time

Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state.

TX Hello Msgs

Specifies the number of SDP echo request messages transmitted after the keepalive was administratively enabled or the counter was cleared.

Rx Hello Msgs

Specifies the number of SDP echo request messages received after the keepalive was administratively enabled or the counter was cleared.

Associated LSP List

When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field.

sdp-using
Syntax

sdp-using [sdp-id[:vc-id] | far-end ip-address]

Context

show>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays services using SDP or far-end address options.

Parameters
sdp-id

Displays only services bound to the specified SDP ID.

Values

1 to 17407

vc-id

Specifies the virtual circuit identifier.

Values

1 to 4294967295

far-end ip-address

Displays only services matching the specified far-end IP address.

Default

Services with any far-end IP address.

Output

The following output is an example of SDP information, and Output fields: service SDP-using describes the output fields.

Sample output
*A:ALA-1# show service sdp-using 300
===============================================================================
Service Destination Point (Sdp Id : 300)
===============================================================================
SvcId       SdpId               Type Far End        Opr State I.Label  E.Label
-------------------------------------------------------------------------------
1           300:1               Mesh 10.0.0.13      Up        131071   131071
2           300:2               Spok 10.0.0.13      Up        131070   131070
100         300:100             Mesh 10.0.0.13      Up        131069   131069
101         300:101             Mesh 10.0.0.13      Up        131068   131068
102         300:102             Mesh 10.0.0.13      Up        131067   131067
-------------------------------------------------------------------------------
Number of SDPs : 5
-------------------------------------------------------------------------------
*A:ALA-1#
*A:ces-A# show service sdp-using 
===============================================================================
SDP Using
===============================================================================
SvcId       SdpId               Type    Far End        Opr S* I.Label  E.Label 
-------------------------------------------------------------------------------
1           12:1                Spok    2.2.2.2        Up     131063   131062  
2           12:2                Spok    2.2.2.2        Up     131062   131069  
3           122:3               Spok    2.2.2.2        Up     131069   131068  
4           12:4                Spok    2.2.2.2        Up     131061   131061  
-------------------------------------------------------------------------------
Number of SDPs : 4
-------------------------------------------------------------------------------
===============================================================================
*A:ces-A# 
Table 5. Output fields: service SDP-using
Label Description

Svc ID

The service identifier.

Sdp ID

The SDP identifier.

Type

Type of SDP: spoke or mesh.

Far End

The far end address of the SDP.

Oper State

The operational state of the service.

Ingress Label

The label used by the far-end device to send packets to this device in this service by this SDP.

Egress Label

The label used by this device to send packets to the far-end device in this service by this SDP.

service-using
Syntax

service-using [sdp sdp-id] [b-vpls] [i-vpls] [m-vpls] [sdp sdp-id] [customer customer-id]

Context

show>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays the services matching the specified usage properties.

If no optional parameters are specified, all services defined on the system are displayed.

Parameters
b-vpls

Specifies the B-component instance of the Provider Backbone Bridging (PBB/IEEE 802.1ah) feature. It represents the multi-point tunneling component that multiplexes multiple customer VPNs (ISIDs) together. It is similar to a regular VPLS instance that operates on the backbone MAC addresses.

i-vpls

Specifies the I-component instance of the Provider Backbone Bridging (PBB/IEEE 802.1ah) feature. It identifies the specific VPN entity associated with a customer multipoint (ELAN) service. It is similar to a regular VPLS instance that operates on the customer MAC addresses.

m-vpls

Specifies the M-component (managed VPLS) instance of the Provider Backbone Bridging (PBB/IEEE 802.1ah) feature.

sdp sdp-id

Displays only services bound to the specified SDP ID.

Default

Services bound to any SDP ID.

Values

1 to 17407

customer customer-id

Displays services only associated with the specified customer ID.

Default

Services associated with any customer.

Values

1 to 2147483647

Output

The following output is an example of service information, and Output fields: service service-using describes the output fields.

Sample output
*A:ALA-12# show service service-using customer 10
==============================================================================
Services
==============================================================================
ServiceId    Type      Adm    Opr        CustomerId        Last Mgmt Change
------------------------------------------------------------------------------
1            VPLS      Up     Up         10                09/05/2006 13:24:15
300          Epipe     Up     Up         10                09/05/2006 13:24:15
------------------------------------------------------------------------------
Matching Services : 
==============================================================================
*A:ALA-12#


*A:ALA-12# show service service-using
===============================================================================
Services
===============================================================================
ServiceId    Type      Adm    Opr        CustomerId        Last Mgmt Change
-------------------------------------------------------------------------------
1            uVPLS     Up     Up         1                 10/26/2006 15:44:57
2            Epipe     Up     Down       1                 10/26/2006 15:44:57
10           mVPLS     Down   Down       1                 10/26/2006 15:44:57
11           mVPLS     Down   Down       1                 10/26/2006 15:44:57
100          mVPLS     Up     Up         1                 10/26/2006 15:44:57
101          mVPLS     Up     Up         1                 10/26/2006 15:44:57
102          mVPLS     Up     Up         1                 10/26/2006 15:44:57
999          uVPLS     Down   Down       1                 10/26/2006 16:14:33
-------------------------------------------------------------------------------
Matching Services : 8
-------------------------------------------------------------------------------
*A:ALA-12#
Table 6. Output fields: service service-using
Label Description

Service Id

The service identifier.

Type

Specifies the service type configured for the service ID.

Adm

The configured state of the service.

Opr

The operating state of the service.

CustomerID

The ID of the customer who owns this service.

Last Mgmt Change

The date and time of the most recent management-initiated change to this service.

id
Syntax

id service-id {all | arp | base | endpoint fdb | label |sap | split-horizon-group |stp | interface | mstp-configuration}

Context

show>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays information for a particular service ID.

Parameters
service-id

Specifies the service identification number that identifies the service in the domain.

Values

service-id: 1 to 214748364

svc-name: A string up to 64 characters.

all

Displays all information about the service.

arp

Displays ARP entries for the service.

base

Displays basic service information.

endpoint

Displays service endpoint information.

fdb

Displays FDB information.

interface

Displays service interfaces.

labels

Displays labels being used by this service.

mstp-configuration

Display MSTP information.

sap

Displays SAPs associated with the service.

sdp

Displays SDPs associated with the service.

split-horizon-group

Displays split horizon group information.

stp

Displays STP information.

Output

The following output is an example of service ID information.

Sample output
*A:ces-A# show service id 1 sap 
=========================================================================
SAP(Summary), Service 1
=========================================================================
PortId                          SvcId      Ing.  Ing.    Egr.   Adm  Opr       
                                           QoS   Fltr    Fltr                  
-------------------------------------------------------------------------
1/2/1.1                         1          1     none    none   Up   Up  
-------------------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------------------
=========================================================================
all
Syntax

all

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays more information for all aspects of the service.

Output

The following outputs are examples of detailed service information, and Output fields: service ID All describes the output fields:

Sample output
*A:Dut-A>show>service>id# all

===============================================================================
Service Detailed Information
===============================================================================
Service Id        : 1501                Vpn Id            : 1501
Service Type      : Epipe
Description       : Default epipe description for service id 1501
Customer Id       : 1
Last Status Change: 02/21/2011 13:07:03
Last Mgmt Change  : 02/21/2011 13:03:58
Admin State       : Up                  Oper State        : Up
MTU               : 1514
MTU Check         : Enabled
Vc Switching      : False
SAP Count         : 1                   SDP Bind Count    : 2
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
 Sdp Id 1413:1501  -(10.20.1.4)
-------------------------------------------------------------------------------
Description     : Default sdp description
SDP Id             : 1413:1501                Type              : Spoke
VC Type            : Ether                    VC Tag            : n/a
Admin Path MTU     : 0                        Oper Path MTU     : 9182
Far End            : 10.20.1.4                Delivery          : MPLS

Admin State        : Up                       Oper State        : Up
Acct. Pol          : 14                       Collect Stats     : Enabled
Ingress Label      : 130948                   Egress Label      : 130483
Ing mac Fltr       : n/a                      Egr mac Fltr      : n/a
Ing ip Fltr        : n/a                      Egr ip Fltr       : n/a
Admin ControlWord  : Preferred                Oper ControlWord  : True
Admin BW(Kbps)     : 0                        Oper BW(Kbps)     : 0
Last Status Change : 02/21/2011 13:07:12      Signaling         : TLDP
Last Mgmt Change   : 02/21/2011 13:03:58      Force Vlan-Vc     : Disabled
Endpoint           : coreSide                 Precedence        : 1
Class Fwding State : Down
Flags              : None
Peer Pw Bits       : None
Peer Fault Ip      : None
Peer Vccv CV Bits  : lspPing
Peer Vccv CC Bits  : pwe3ControlWord mplsRouterAlertLabel

KeepAlive Information :
Admin State        : Enabled                  Oper State        : Alive
Hello Time         : 10                       Hello Msg Len     : 0
Max Drop Count     : 3                        Hold Down Time    : 10

Statistics            :
I. Fwd. Pkts.      : 48319                    I. Fwd. Octs.     : 5690869
E. Fwd. Pkts.      : 34747                    E. Fwd. Octets    : 4013709
-------------------------------------------------------------------------------
Eth-Cfm Configuration Information
-------------------------------------------------------------------------------
Md-index           : 1000                     Direction         : Down
Ma-index           : 1150114                  Admin             : Enabled
MepId              : 1                        CCM-Enable        : Enabled
LowestDefectPri    : macRemErrXcon            HighestDefect     : none
Defect Flags       : None
Mac Address        : 7c:20:64:ad:04:07        ControlMep        : False
CcmLtmPriority     : 7
CcmTx              : 11385                    CcmSequenceErr    : 0
Eth-1Dm Threshold  : 3(sec)
Eth-Ais:           : Disabled
Eth-Tst:           : Disabled
LbRxReply          : 0                        LbRxBadOrder      : 0
LbRxBadMsdu        : 0                        LbTxReply         : 0
LbNextSequence     : 1                        LtNextSequence    : 1
LtRxUnexplained    : 0

Associated LSP LIST :
Lsp Name           : A_D_21
Admin State        : Up                       Oper State        : Up
Time Since Last Tr*: 03h49m30s

-------------------------------------------------------------------------------
 Sdp Id 1613:1501  -(10.20.1.6)
-------------------------------------------------------------------------------
Description     : Default sdp description
SDP Id             : 1613:1501                Type              : Spoke
VC Type            : Ether                    VC Tag            : n/a
Admin Path MTU     : 0                        Oper Path MTU     : 9182
Far End            : 10.20.1.6                Delivery          : MPLS

Admin State        : Up                       Oper State        : Up
Acct. Pol          : 14                       Collect Stats     : Enabled
Ingress Label      : 130526                   Egress Label      : 130424
Ing mac Fltr       : n/a                      Egr mac Fltr      : n/a
Ing ip Fltr        : n/a                      Egr ip Fltr       : n/a
Admin ControlWord  : Not Preferred            Oper ControlWord  : False
Admin BW(Kbps)     : 0                        Oper BW(Kbps)     : 0
Last Status Change : 02/21/2011 13:07:03      Signaling         : TLDP
Last Mgmt Change   : 02/21/2011 13:03:58      Force Vlan-Vc     : Disabled
Endpoint           : coreSide                 Precedence        : 2
Class Fwding State : Down
Flags              : None
Peer Pw Bits       : pwFwdingStandby
Peer Fault Ip      : None
Peer Vccv CV Bits  : lspPing
Peer Vccv CC Bits  : mplsRouterAlertLabel

KeepAlive Information :
Admin State        : Enabled                  Oper State        : Alive
Hello Time         : 10                       Hello Msg Len     : 0
Max Drop Count     : 3                        Hold Down Time    : 10

Statistics            :
I. Fwd. Pkts.      : 25                       I. Fwd. Octs.     : 2776
E. Fwd. Pkts.      : 23                       E. Fwd. Octets    : 2557
-------------------------------------------------------------------------------
Eth-Cfm Configuration Information
-------------------------------------------------------------------------------
Md-index           : 1000                     Direction         : Down
Ma-index           : 1150116                  Admin             : Enabled
MepId              : 1                        CCM-Enable        : Enabled
LowestDefectPri    : macRemErrXcon            HighestDefect     : none
Defect Flags       : None
Mac Address        : 7c:20:64:ad:04:07        ControlMep        : False
CcmLtmPriority     : 7
CcmTx              : 11414                    CcmSequenceErr    : 0
Eth-1Dm Threshold  : 3(sec)
Eth-Ais:           : Disabled
Eth-Tst:           : Disabled
LbRxReply          : 0                        LbRxBadOrder      : 0
LbRxBadMsdu        : 0                        LbTxReply         : 0
LbNextSequence     : 1                        LtNextSequence    : 1
LtRxUnexplained    : 0

Associated LSP LIST :
Lsp Name           : A_F_21
Admin State        : Up                       Oper State        : Up
Time Since Last Tr*: 03h48m45s

-------------------------------------------------------------------------------
Number of SDPs : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
SAP lag-3:1501.1501
-------------------------------------------------------------------------------
Service Id         : 1501
SAP                : lag-3:1501.1501          Encap             : qinq
QinQ Dot1p         : Default
Description        : (Not Specified)
Admin State        : Up                       Oper State        : Up
Flags              : None
Last Status Change : 02/21/2011 13:06:45
Last Mgmt Change   : 02/21/2011 13:03:58

Admin MTU          : 9212                     Oper MTU          : 9212
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : 1501                     Egr Mac Fltr-Id   : n/a
tod-suite          : None
Egr Agg Rate Limit : max
Endpoint           : accessSide

Acct. Pol          : Default                  Collect Stats     : Enabled


-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1500                     Egress qos-policy : 1500
-------------------------------------------------------------------------------
Sap Egress Policy (1500)
-------------------------------------------------------------------------------
Scope              : Template
Remark             : False                    Remark Pol Id     : 2
Accounting         : frame-based
Description    : Sap Egress Policy for svcList 1500
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        CIR          CIR Adpt Rule        PIR          PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1          10000          max                10000          max
Queue2          10000          max                10000          max
Queue3          10000          max                10000          max
Queue4          10000          max                10000          max
Queue5          10000          max                10000          max
Queue6          10000          max                10000          max
Queue7          10000          max                10000          max
Queue8          10000          max                10000          max
-------------------------------------------------------------------------------
Parent Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId          Port       CIR Level      PIR Weight
-------------------------------------------------------------------------------
Queue1          True             1             1
Queue2          True             2             2
Queue3          True             3             3
Queue4          True             4             4
Queue5          True             5             5
Queue6          True             6             6
Queue7          True             7             7
Queue8          True             8             8
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1           Up             50           100            50
Queue2           Up             50           100            50
Queue3           Up             50           100            50
Queue4           Up             50           100            50
Queue5           Up             50           100            50
Queue6           Up             50           100            50
Queue7           Up             50           100            50
Queue8           Up             50           100            50
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1           Up             10           50            50
Queue2           Up             10           50            50
Queue3           Up             10           50            50
Queue4           Up             10           50            50
Queue5           Up             10           50            50
Queue6           Up             10           50            50
Queue7           Up             10           50            50
Queue8           Up             10           50            50
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId         CBS            MBS       Time Average Factor        Queue-Mgmt
-------------------------------------------------------------------------------
Queue1          200               400              10           qM_1500
Queue2          200               400              10           qM_1500
Queue3          200               400              10           qM_1500
Queue4          200               400              10           qM_1500
Queue5          200               400              10           qM_1500
Queue6          200               400              10           qM_1500
Queue7          200               400              10           qM_1500
Queue8          200               400              10           qM_1500
-------------------------------------------------------------------------------
Aggregate Policer (Available)
-------------------------------------------------------------------------------
rate               : n/a                      burst             : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 32                    Meters Allocated   : 16
Classifiers Used     : 8                     Meters Used        : 5
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Stats:          34659                   3241035
Egress Stats:           48099                   5291928
Extra-Tag Drop Stats:   n/a                     n/a
-------------------------------------------------------------------------------
Sap per Meter stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Ingress Meter 1 (Unicast)
For. InProf           : 7209                    468585
For. OutProf          : 0                       0

Ingress Meter 2 (Unicast)
For. InProf           : 0                       0
For. OutProf          : 0                       0

Ingress Meter 3 (Unicast)
For. InProf           : 0                       0
For. OutProf          : 0                       0

Ingress Meter 4 (Unicast)
For. InProf           : 0                       0
For. OutProf          : 0                       0

Ingress Meter 5 (Unicast)
For. InProf           : 27454                   2772854
For. OutProf          : 0                       0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Egress Queue 1 (be)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 2 (l2)
Fwd Stats            :  3                       180
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 3 (af)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 4 (l1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 5 (h2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 6 (ef)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 7 (h1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 8 (nc)
Fwd Stats            :  20842                   1938306
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
Endpoint name                : coreSide
Description                  : (Not Specified)
Revert time                  : 0
Act Hold Delay               : 0
Standby Signaling Master     : true
Tx Active                    : 1413:1501
Tx Active Up Time            : 0d 03:48:41
Revert Time Count Down       : N/A
Tx Active Change Count       : 2
Last Tx Active Change        : 02/21/2011 13:07:12
-------------------------------------------------------------------------------
Members
-------------------------------------------------------------------------------
Spoke-sdp: 1413:1501 Prec:1                         Oper Status: Up
Spoke-sdp: 1613:1501 Prec:2                         Oper Status: Up
===============================================================================
Endpoint name                : accessSide
Description                  : (Not Specified)
Revert time                  : 0
Act Hold Delay               : 0
Standby Signaling Master     : false
Tx Active                    : lag-3:1501.1501
Tx Active Up Time            : 0d 03:49:08
Revert Time Count Down       : N/A
Tx Active Change Count       : 1
Last Tx Active Change        : 02/21/2011 13:06:45
-------------------------------------------------------------------------------
Members
-------------------------------------------------------------------------------
SAP      : lag-3:1501.1501                          Oper Status: Up
===============================================================================
===============================================================================


*A:DUT-B_sasx>show>service# id 257 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id        : 257                 Vpn Id            : 0
Service Type      : Epipe
Description       : (Not Specified)
Customer Id       : 257
Last Status Change: 05/20/2000 11:03:07
Last Mgmt Change  : 05/20/2000 11:03:07
Admin State       : Up                  Oper State        : Up
MTU               : 1514
MTU Check         : Enabled
Vc Switching      : False
SAP Count         : 1                   SDP Bind Count    : 2
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
 Sdp Id 12:64  -(1.1.1.1)
-------------------------------------------------------------------------------
Description     : (Not Specified)
SDP Id             : 12:64                    Type              : Spoke
VC Type            : Ether                    VC Tag            : n/a
Admin Path MTU     : 0                        Oper Path MTU     : 9186
Far End            : 1.1.1.1                  Delivery          : LDP

Admin State        : Up                       Oper State        : Up
Acct. Pol          : None                     Collect Stats     : Disabled
Ingress Label      : 130940                   Egress Label      : 130747
Ing mac Fltr       : n/a                      Egr mac Fltr      : n/a
Ing ip Fltr        : n/a                      Egr ip Fltr       : n/a
Admin ControlWord  : Not Preferred            Oper ControlWord  : False
Admin BW(Kbps)     : 0                        Oper BW(Kbps)     : 0
Last Status Change : 05/20/2000 12:26:22      Signaling         : TLDP
Last Mgmt Change   : 05/20/2000 11:01:59      Force Vlan-Vc     : Disabled
Endpoint           : y                        Precedence        : 4
Class Fwding State : Down
Flags              : None
Peer Pw Bits       : None
Peer Fault Ip      : None
Peer Vccv CV Bits  : None
Peer Vccv CC Bits  : None

KeepAlive Information :
Admin State        : Enabled                  Oper State        : Alive
Hello Time         : 10                       Hello Msg Len     : 0
Max Drop Count     : 3                        Hold Down Time    : 10

Statistics            :
I. Fwd. Pkts.      : 0                        I. Fwd. Octs.     : 0
E. Fwd. Pkts.      : 1981718                  E. Fwd. Octets    : 3016174796
-------------------------------------------------------------------------------
 Sdp Id 24:64  -(4.4.4.4)
-------------------------------------------------------------------------------
Description     : (Not Specified)
SDP Id             : 24:64                    Type              : Spoke
VC Type            : Ether                    VC Tag            : n/a
Admin Path MTU     : 0                        Oper Path MTU     : 9186
Far End            : 4.4.4.4                  Delivery          : LDP

Admin State        : Up                       Oper State        : Up
Acct. Pol          : None                     Collect Stats     : Disabled
Ingress Label      : 130939                   Egress Label      : 130744
Ing mac Fltr       : n/a                      Egr mac Fltr      : n/a
Ing ip Fltr        : n/a                      Egr ip Fltr       : n/a
Admin ControlWord  : Not Preferred            Oper ControlWord  : False
Admin BW(Kbps)     : 0                        Oper BW(Kbps)     : 0
Last Status Change : 05/20/2000 12:28:58      Signaling         : TLDP
Last Mgmt Change   : 05/20/2000 11:03:07      Force Vlan-Vc     : Disabled
Endpoint           : y                        Precedence        : 4
Class Fwding State : Down
Flags              : None
Peer Pw Bits       : None
Peer Fault Ip      : None
Peer Vccv CV Bits  : None
Peer Vccv CC Bits  : None

KeepAlive Information :
Admin State        : Enabled                  Oper State        : Alive
Hello Time         : 10                       Hello Msg Len     : 0
Max Drop Count     : 3                        Hold Down Time    : 10

Statistics            :
I. Fwd. Pkts.      : 0                        I. Fwd. Octs.     : 0
E. Fwd. Pkts.      : 2020669                  E. Fwd. Octets    : 3075458218
-------------------------------------------------------------------------------
Number of SDPs : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/3:64
-------------------------------------------------------------------------------
Service Id         : 257
SAP                : 1/1/3:64                 Encap             : q-tag
Description        : (Not Specified)
Admin State        : Up                       Oper State        : Up
Flags              : None
Last Status Change : 05/19/2000 12:13:40
Last Mgmt Change   : 05/20/2000 11:00:53
Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100

Admin MTU          : 1518                     Oper MTU          : 1518
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
tod-suite          : None
Endpoint           : x

Acct. Pol          : None                     Collect Stats     : Disabled
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1                        Egress qos-policy : 1
-------------------------------------------------------------------------------
Sap Egress Policy (1)
-------------------------------------------------------------------------------
Scope              : Template
Remark             : False                    Remark Pol Id     : 2
Accounting         : frame-based
Description    : Default SAP egress QoS policy.
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        CIR          CIR Adpt Rule        PIR          PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1          0              closest            max            closest
Queue2          0              closest            max            closest
Queue3          0              closest            max            closest
Queue4          0              closest            max            closest
Queue5          0              closest            max            closest
Queue6          0              closest            max            closest
Queue7          0              closest            max            closest
Queue8          0              closest            max            closest
-------------------------------------------------------------------------------
Parent Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId          Port       CIR Level      PIR Weight
-------------------------------------------------------------------------------
Queue1          True             1             1
Queue2          True             1             1
Queue3          True             1             1
Queue4          True             1             1
Queue5          True             1             1
Queue6          True             1             1
Queue7          True             1             1
Queue8          True             1             1
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            70           90            75
Queue2          Down            70           90            75
Queue3          Down            70           90            75
Queue4          Down            70           90            75
Queue5          Down            70           90            75
Queue6          Down            70           90            75
Queue7          Down            70           90            75
Queue8          Down            70           90            75
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            50           75            75
Queue2          Down            50           75            75
Queue3          Down            50           75            75
Queue4          Down            50           75            75
Queue5          Down            50           75            75
Queue6          Down            50           75            75
Queue7          Down            50           75            75
Queue8          Down            50           75            75
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId         CBS            MBS       Time Average Factor        Queue-Mgmt
-------------------------------------------------------------------------------
Queue1          def               def              7           default
Queue2          def               def              7           default
Queue3          def               def              7           default
Queue4          def               def              7           default
Queue5          def               def              7           default
Queue6          def               def              7           default
Queue7          def               def              7           default
Queue8          def               def              7           default
-------------------------------------------------------------------------------
Aggregate Policer (Not Available)
-------------------------------------------------------------------------------
rate               : n/a                      burst             : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4                     Meters Allocated   : 2
Classifiers Used     : 1                     Meters Used        : 1
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Stats:          5496351                 8244526500
Egress Stats:           0                       0
-------------------------------------------------------------------------------
Sap per Meter stats
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Meter 1 (Unicast)
For. InProf           : 3                       4500
For. OutProf          : 5506597                 8259894000
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
                        Packets                 Octets
Egress Queue 1 (be)
Fwd Stats            :  56935                   86541200
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 2 (l2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 3 (af)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 4 (l1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 5 (h2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 6 (ef)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 7 (h1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 8 (nc)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
Endpoint name                : x
Description                  : (Not Specified)
Revert time                  : 0
Act Hold Delay               : 0
Ignore Standby Signaling     : false
Suppress Standby Signaling   : true
Block On Mesh Fail           : false
Tx Active                    : 1/1/3:64
Tx Active Up Time            : 0d 01:31:46
Revert Time Count Down       : N/A
Tx Active Change Count       : 0
Last Tx Active Change        : 05/19/2000 12:13:40
-------------------------------------------------------------------------------
Members
-------------------------------------------------------------------------------
SAP      : 1/1/3:64                                 Oper Status: Up
===============================================================================
Endpoint name                : y
Description                  : (Not Specified)
Revert time                  : 0
Act Hold Delay               : 0
Ignore Standby Signaling     : false
Suppress Standby Signaling   : true
Block On Mesh Fail           : false
Tx Active                    : 12:64
Tx Active Up Time            : 0d 00:00:27
Revert Time Count Down       : N/A
Tx Active Change Count       : 105
Last Tx Active Change        : 05/20/2000 12:32:15
-------------------------------------------------------------------------------
Members
-------------------------------------------------------------------------------
Spoke-sdp: 12:64 Prec:4                             Oper Status: Up
Spoke-sdp: 24:64 Prec:4                             Oper Status: Up
===============================================================================
===============================================================================
*A:DUT-B_sasx>show>service#
Sample output (split horizon group)
*A:SASX>show>service# id 1 all

===============================================================================
Service Detailed Information
===============================================================================
Service Id        : 1                   Vpn Id            : 0
Service Type      : VPLS
Description       : (Not Specified)
Customer Id       : 1
Last Status Change: 07/22/2011 13:24:25
Last Mgmt Change  : 07/21/2011 09:04:33
Admin State       : Up                  Oper State        : Up
MTU               : 1514                Def. Mesh VC Id   : 1
MTU Check         : Enabled
SAP Count         : 2                   SDP Bind Count    : 0
Snd Flush on Fail : Disabled            Host Conn Verify  : Disabled

-------------------------------------------------------------------------------
Split Horizon Group specifics
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Split Horizon Group : access
-------------------------------------------------------------------------------
Description       : (Not Specified)
Instance Id       : 1                   Last Change       : 07/21/2011 09:03:50

-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
SAP 1/1/1:10
-------------------------------------------------------------------------------
Service Id         : 1
SAP                : 1/1/1:10                 Encap             : q-tag
Description        : (Not Specified)
Admin State        : Up                       Oper State        : Up
Flags              : None
Last Status Change : 07/21/2011 08:47:19
Last Mgmt Change   : 07/22/2011 13:24:25
Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100
Split Horizon Group: (Not Specified)

Max Nbr of MAC Addr: No Limit                 Total MAC Addr    : 0
Learned MAC Addr   : 0                        Static MAC Addr   : 0
Admin MTU          : 1518                     Oper MTU          : 1518
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
Ingr IPv6 Fltr-Id  : n/a                      Egr IPv6 Fltr-Id  : n/a
tod-suite          : None
Egr Agg Rate Limit : max
Mac Learning       : Enabled                  Discard Unkwn Srce: Disabled
Mac Aging          : Enabled                  Mac Pinning       : Disabled
BPDU Translation   : Disabled
L2PT Termination   : Disabled

Acct. Pol          : None                     Collect Stats     : Disabled
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State    : Up                       Stp Oper State    : Down
Core Connectivity  : Down
Port Role          : N/A                      Port State        : Forwarding
Port Number        : 2048                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A
CIST Desig Bridge  : N/A                      Designated Port   : N/A

Forward transitions: 0                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
TC bit BPDUs rcvd  : 0                        TC bit BPDUs tx   : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 0                        MST BPDUs tx      : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State        : outOfService
Host Limit         : 1                        Min Auth Interval : 15 minutes

-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1                        Egress qos-policy : 1
-------------------------------------------------------------------------------
Sap Egress Policy (1)
-------------------------------------------------------------------------------
Scope              : Template
Remark             : False                    Remark Pol Id     : 2
Accounting         : frame-based
Description    : Default SAP egress QoS policy.
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        CIR          CIR Adpt Rule        PIR          PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1          0              closest            max            closest
Queue2          0              closest            max            closest
Queue3          0              closest            max            closest
Queue4          0              closest            max            closest
Queue5          0              closest            max            closest
Queue6          0              closest            max            closest
Queue7          0              closest            max            closest
Queue8          0              closest            max            closest
-------------------------------------------------------------------------------
Parent Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId          Port       CIR Level      PIR Weight
-------------------------------------------------------------------------------
Queue1          True             1             1
Queue2          True             1             1
Queue3          True             1             1
Queue4          True             1             1
Queue5          True             1             1
Queue6          True             1             1
Queue7          True             1             1
Queue8          True             1             1
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            70           90            75
Queue2          Down            70           90            75
Queue3          Down            70           90            75
Queue4          Down            70           90            75
Queue5          Down            70           90            75
Queue6          Down            70           90            75
Queue7          Down            70           90            75
Queue8          Down            70           90            75
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            50           75            75
Queue2          Down            50           75            75
Queue3          Down            50           75            75
Queue4          Down            50           75            75
Queue5          Down            50           75            75
Queue6          Down            50           75            75
Queue7          Down            50           75            75
Queue8          Down            50           75            75
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId         CBS            MBS       Time Average Factor        Queue-Mgmt
-------------------------------------------------------------------------------
Queue1          def               def              7           default
Queue2          def               def              7           default
Queue3          def               def              7           default
Queue4          def               def              7           default
Queue5          def               def              7           default
Queue6          def               def              7           default
Queue7          def               def              7           default
Queue8          def               def              7           default
-------------------------------------------------------------------------------
Aggregate Policer (Available)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
rate               : n/a                      burst             : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4                     Meters Allocated   : 2
Classifiers Used     : 2                     Meters Used        : 2
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Stats:          0                       0
Egress Stats:           0                       0
Ingress Drop Stats:     0                       0

Extra-Tag Drop Stats:   n/a                     n/a
-------------------------------------------------------------------------------
Sap per Meter stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Ingress Meter 1 (Unicast)
For. InProf           : 0                       0
For. OutProf          : 0                       0

Ingress Meter 11 (Multipoint)
For. InProf           : 0                       0
For. OutProf          : 0                       0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Egress Queue 1 (be)
Fwd Stats            :  333437964               501490697856
Drop InProf          :  0                       0
Drop OutProf         :  329635022               495771073088

Egress Queue 2 (l2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 3 (af)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 4 (l1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 5 (h2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 6 (ef)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 7 (h1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 8 (nc)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

-------------------------------------------------------------------------------
SAP 1/1/25:10
-------------------------------------------------------------------------------
Service Id         : 1
SAP                : 1/1/25:10                Encap             : q-tag
Description        : (Not Specified)
Admin State        : Up                       Oper State        : Up
Flags              : None
Last Status Change : 07/21/2011 08:47:19
Last Mgmt Change   : 07/22/2011 13:24:29
Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100
Split Horizon Group: (Not Specified)

Max Nbr of MAC Addr: No Limit                 Total MAC Addr    : 0
Learned MAC Addr   : 0                        Static MAC Addr   : 0
Admin MTU          : 1518                     Oper MTU          : 1518
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
Ingr IPv6 Fltr-Id  : n/a                      Egr IPv6 Fltr-Id  : n/a
tod-suite          : None
Egr Agg Rate Limit : max
Mac Learning       : Enabled                  Discard Unkwn Srce: Disabled
Mac Aging          : Enabled                  Mac Pinning       : Disabled
BPDU Translation   : Disabled
L2PT Termination   : Disabled

Acct. Pol          : None                     Collect Stats     : Disabled



-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State    : Up                       Stp Oper State    : Down
Core Connectivity  : Down
Port Role          : N/A                      Port State        : Forwarding
Port Number        : 2049                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A
CIST Desig Bridge  : N/A                      Designated Port   : N/A

Forward transitions: 0                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
TC bit BPDUs rcvd  : 0                        TC bit BPDUs tx   : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 0                        MST BPDUs tx      : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State        : outOfService
Host Limit         : 1                        Min Auth Interval : 15 minutes

-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1                        Egress qos-policy : 1
-------------------------------------------------------------------------------
Sap Egress Policy (1)
-------------------------------------------------------------------------------
Scope              : Template
Remark             : False                    Remark Pol Id     : 2
Accounting         : frame-based
Description    : Default SAP egress QoS policy.
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        CIR          CIR Adpt Rule        PIR          PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1          0              closest            max            closest
Queue2          0              closest            max            closest
Queue3          0              closest            max            closest
Queue4          0              closest            max            closest
Queue5          0              closest            max            closest
Queue6          0              closest            max            closest
Queue7          0              closest            max            closest
Queue8          0              closest            max            closest
-------------------------------------------------------------------------------
Parent Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId          Port       CIR Level      PIR Weight
-------------------------------------------------------------------------------
Queue1          True             1             1
Queue2          True             1             1
Queue3          True             1             1
Queue4          True             1             1
Queue5          True             1             1
Queue6          True             1             1
Queue7          True             1             1
Queue8          True             1             1
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            70           90            75
Queue2          Down            70           90            75
Queue3          Down            70           90            75
Queue4          Down            70           90            75
Queue5          Down            70           90            75
Queue6          Down            70           90            75
Queue7          Down            70           90            75
Queue8          Down            70           90            75
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            50           75            75
Queue2          Down            50           75            75
Queue3          Down            50           75            75
Queue4          Down            50           75            75
Queue5          Down            50           75            75
Queue6          Down            50           75            75
Queue7          Down            50           75            75
Queue8          Down            50           75            75
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId         CBS            MBS       Time Average Factor        Queue-Mgmt
-------------------------------------------------------------------------------
Queue1          def               def              7           default
Queue2          def               def              7           default
Queue3          def               def              7           default
Queue4          def               def              7           default
Queue5          def               def              7           default
Queue6          def               def              7           default
Queue7          def               def              7           default
Queue8          def               def              7           default
-------------------------------------------------------------------------------
Aggregate Policer (Available)
-------------------------------------------------------------------------------
rate               : n/a                      burst             : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4                     Meters Allocated   : 2
Classifiers Used     : 2                     Meters Used        : 2
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Stats:          662979085               997120543840
Egress Stats:           0                       0
Ingress Drop Stats:     0                       0

Extra-Tag Drop Stats:   n/a                     n/a
-------------------------------------------------------------------------------
Sap per Meter stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Ingress Meter 1 (Unicast)
For. InProf           : 0                       0
For. OutProf          : 0                       0

Ingress Meter 11 (Multipoint)
For. InProf           : 3                       4512
For. OutProf          : 662979118               997120593472
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Egress Queue 1 (be)
Fwd Stats            :  663030839               997198381856
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 2 (l2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 3 (af)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 4 (l1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 5 (h2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 6 (ef)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 7 (h1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 8 (nc)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state    : Up                       Core Connectivity : Down
Stp Admin State    : Down                     Stp Oper State    : Down
Mode               : Rstp                     Vcp Active Prot.  : N/A

Bridge Id          : 80:00.7c:20:64:ad:09:87  Bridge Instance Id: 0
Bridge Priority    : 32768                    Tx Hold Count     : 6
Topology Change    : Inactive                 Bridge Hello Time : 2
Last Top. Change   : 0d 00:00:00              Bridge Max Age    : 20
Top. Change Count  : 0                        Bridge Fwd Delay  : 15

Root Bridge        : N/A
Primary Bridge     : N/A

Root Path Cost     : 0                        Root Forward Delay: 0
Rcvd Hello Time    : 0                        Root Max Age      : 0
Root Priority      : 0                        Root Port         : N/A

-------------------------------------------------------------------------------
Forwarding Database specifics
-------------------------------------------------------------------------------
Service Id        : 1                   Mac Move          : Disabled
Mac Move Rate     : 2                   Mac Move Timeout  : 10
Mac Move Retries  : 3
Table Size        : 250                 Total Count       : 0
Learned Count     : 0                   Static Count      : 0
OAM-learned Count : 0                   DHCP-learned Count: 0
Remote Age        : 900                 Local Age         : 300
High Watermark    : 95%                 Low Watermark     : 90%
Mac Learning      : Enabled             Discard Unknown   : Disabled
Mac Aging         : Enabled             Relearn Only      : False

-------------------------------------------------------------------------------
===============================================================================
IGMP Snooping Base info for service 1
===============================================================================
Admin State : Up
Querier     : No querier found
-------------------------------------------------------------------------------
Sap/Sdp                    Oper  MRtr Send  Max  MVR       Num
Id                         State Port Qries Grps From-VPLS Grps
-------------------------------------------------------------------------------
sap:1/1/1:1                Up    No   No    None Local     13
sap:1/1/10:1               Up    No   No    None Local     0
==============================================================================
===============================================================================
Sample output (meter-override)
A:7210SAS>show>service# id 1101 sap 1/2/1:1 detail
Ingress Meter Override
-------------------------------------------------------------------------------

Meter Id           : 1
Admin PIR          : 12000                    Admin CIR         : 10000
Oper PIR           : 12000                    Oper CIR          : 10000
PIR Rule           : closest*                 CIR Rule          : closest*
MBS                : 20 KBytes CBS : 15 Kbytes
Mode               : Trtcm2*

* means the value is inherited
-------------------------------------------------------------------------------
A:7210SAS>show>service#
Sample output (entropy/hash-label)
*A:7210SAS>config>service# /show service id 1 all 

===============================================================================
Service Detailed Information
===============================================================================
Service Id        : 1                   Vpn Id            : 0
Service Type      : VPLS                
Name              : (Not Specified)
Description       : (Not Specified)
Customer Id       : 1                   
Last Status Change: 01/07/2000 21:19:14 
Last Mgmt Change  : 01/07/2000 21:15:25 
Admin State       : Up                  Oper State        : Up
MTU               : 1514                Def. Mesh VC Id   : 1
MTU Check         : Enabled             
SAP Count         : 0                   SDP Bind Count    : 1
Snd Flush on Fail : Disabled            Host Conn Verify  : Disabled
SAP Type:         : Any                 
Propagate MacFlush: Disabled            Per Svc Hashing   : Disabled
Allow IP Intf Bind: Disabled            
 
-------------------------------------------------------------------------------
Split Horizon Group specifics
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults     : ignore              V-Mep Extensions  : Enabled


-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
 Sdp Id 1:1  -(2.2.2.2)
-------------------------------------------------------------------------------
Description     : (Not Specified)
SDP Id             : 1:1                      Type              : Spoke
Spoke Descr     : (Not Specified)
Split Horiz Grp    : (Not Specified)
VC Type            : Ether                    VC Tag            : n/a
Admin Path MTU     : 0                        Oper Path MTU     : 9190
Far End            : 2.2.2.2                  Delivery          : MPLS
Tunnel Far End     : 2.2.2.2                  LSP Types         : LDP
Hash Label         : Enabled                  Hash Lbl Sig Cap  : Disabled
Oper Hash Label    : Enabled                  
 
Admin State        : Up                       Oper State        : Up
Acct. Pol          : None                     Collect Stats     : Disabled
Ingress Label      : 131069                   Egress Label      : 131069
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr IPv6 Fltr-Id  : n/a                      Egr IPv6 Fltr-Id  : n/a
Admin ControlWord  : Not Preferred            Oper ControlWord  : False
Last Status Change : 01/07/2000 21:19:14      Signaling         : TLDP
Last Mgmt Change   : 01/07/2000 21:15:25      Force Vlan-Vc     : Disabled
Endpoint           : N/A                      Precedence        : 4
PW Status Sig      : Enabled                  
Class Fwding State : Down                     
Flags              : None
Local Pw Bits      : None
Peer Pw Bits       : None
Peer Fault Ip      : None                     
 
Application Profile: None                     
Transit Policy     : None                     
Max Nbr of MAC Addr: No Limit                 Total MAC Addr    : 0
Learned MAC Addr   : 0                        Static MAC Addr   : 0
                                      
MAC Learning       : Enabled                  Discard Unkwn Srce: Disabled
MAC Aging          : Enabled                  
BPDU Translation   : Disabled                 
L2PT Termination   : Disabled
MAC Pinning        : Disabled                 
Ignore Standby Sig : False                    Block On Mesh Fail: False
Oper Group         : (none)                   Monitor Oper Grp  : (none)
Rest Prot Src Mac  : Disabled                 
Auto Learn Mac Prot: Disabled                 RestProtSrcMacAct : Disable

Ingress Qos Policy : (none)                   Egress Qos Policy : (none)
Ingress FP QGrp    : (none)                   Egress Port QGrp  : (none)
Ing FP QGrp Inst   : (none)                   Egr Port QGrp Inst: (none)
 
KeepAlive Information :
Admin State        : Disabled                 Oper State        : Disabled
Hello Time         : 10                       Hello Msg Len     : 0
Max Drop Count     : 3                        Hold Down Time    : 10
 
Statistics            :
I. Fwd. Pkts.      : 0                        I. Fwd. Octs.     : 0
E. Fwd. Pkts.      : 0                        E. Fwd. Octets    : 0
Extra-Tag-Drop-Pkts: n/a                      Extra-Tag-Drop-Oc*: n/a

-------------------------------------------------------------------------------
Control Channel Status
-------------------------------------------------------------------------------
PW Status          : disabled                 Refresh Timer     : <none>
Peer Status Expire : false                    
Request Timer      : <none>                   
Acknowledgement    : false                    

-------------------------------------------------------------------------------
ETH-CFM SDP-Bind specifics
-------------------------------------------------------------------------------
V-MEP Filtering    : Disabled                 
 
-------------------------------------------------------------------------------
LDP Information :
-------------------------------------------------------------------------------
LDP LSP Id         : 65537                    
 
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :                 
No LSPs Associated
 
 
-------------------------------------------------------------------------------
Stp Service Destination Point specifics
-------------------------------------------------------------------------------
Stp Admin State    : Up                       Stp Oper State    : Down
Core Connectivity  : Down                     
Port Role          : N/A                      Port State        : Forwarding
Port Number        : 0                        Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A                      
Designated Bridge  : N/A                      Designated Port Id: 0
 
Fwd Transitions    : 0                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
TC bit BPDUs rcvd  : 0                        TC bit BPDUs tx   : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
No Sap Associations

-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state    : Up                       Core Connectivity : Down
Stp Admin State    : Down                     Stp Oper State    : Down
Mode               : Rstp                     Vcp Active Prot.  : N/A
 
Bridge Id          : 80:00.c4:08:4a:59:b2:61  Bridge Instance Id: 0
Bridge Priority    : 32768                    Tx Hold Count     : 6
Topology Change    : Inactive                 Bridge Hello Time : 2
Last Top. Change   : 0d 00:00:00              Bridge Max Age    : 20
Top. Change Count  : 0                        Bridge Fwd Delay  : 15
 
Root Bridge        : N/A                      
Primary Bridge     : N/A                      
 
Root Path Cost     : 0                        Root Forward Delay: 0
Rcvd Hello Time    : 0                        Root Max Age      : 0
Root Priority      : 0                        Root Port         : N/A
 
-------------------------------------------------------------------------------
Forwarding Database specifics
-------------------------------------------------------------------------------
Service Id        : 1                   Mac Move          : Disabled
Mac Move Rate     : 2                   Mac Move Timeout  : 10
Mac Move Retries  : 3                   
Table Size        : 250                 Total Count       : 0
Learned Count     : 0                   Static Count      : 0
OAM-learned Count : 0                   DHCP-learned Count: 0
Remote Age        : 900                 Local Age         : 300
High Watermark    : 95%                 Low Watermark     : 90%
Mac Learning      : Enabled             Discard Unknown   : Disabled
Mac Aging         : Enabled             Relearn Only      : False

-------------------------------------------------------------------------------
IGMP Snooping Base info
-------------------------------------------------------------------------------
Admin State : Down                    
Querier     : No querier found
-------------------------------------------------------------------------------
Sap/Sdp                    Oper  MRtr Send  Max  MVR       Num
Id                         State Port Qries Grps From-VPLS Grps
-------------------------------------------------------------------------------
sdp:1:1                    Up    No   No    None N/A       0

-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
-------------------------------------------------------------------------------

===============================================================================
VPLS Sites
===============================================================================
Site                Site-Id   Dest                Mesh-SDP  Admin   Oper  Fwdr
Table 7. Output fields: service ID All
Label Description

Service Id

The service identifier.

VPN Id

The number that identifies the VPN.

Service Type

Specifies the type of service.

VLL Type

Specifies the VLL type.

SDP Id

The SDP identifier.

Description

Generic information about the service.

Customer Id

The customer identifier.

Last Mgmt Change

The date and time of the most recent management-initiated change.

Endpoint

Specifies the name of the service endpoint.

Flags

Specifies the conditions that affect the operating status of this SAP.

Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, L2OperDown, RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, SapIngressNamedPoolMismatch, SapEgressNamedPoolMismatch, NoSapEpipeRingNode.

SAP Count

The number of SAPs specified for this service.

SDP Bind Count

The number of SDPs bound to this service.

Split Horizon Group Specifics

Split Horizon Group

Name of the split horizon group for this VPLS.

Description

Description of the split horizon group.

Instance ID

Displays the Instance identifier of the split horizon group.

Last Changed

Displays the date and time of most recent change to the split horizon group.

Split Horizon Group

Displays the name of the split horizon group the SAP or spoke-SDP is associated.

Service Destination Points (SDPs)

SDP Id

The SDP identifier.

Type

Indicates whether this Service SDP binding is a spoke or a mesh.

Admin Path MTU

The configured largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Oper Path MTU

The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Delivery

Specifies the type of delivery used by the SDP: MPLS.

Admin State

The administrative state of this SDP.

Oper State

The operational state of this SDP.

Jitter Buffer (packets)

Indicates the jitter buffer length in number of packet buffers.

Playout Threshold (packets)

Indicates the playout buffer packets threshold in number of packet buffers.

Playout Threshold (packets)

Indicates the current packet depth of the jitter buffer.

Peer Pw Bits

Indicates the bits set by the LDP peer when there is a fault on its side of the pseudowire. LAC failures occur on the SAP that has been configured on the pipe service, PSN bits are set by SDP-binding failures on the pipe service. The pwNotForwarding bit is set when none of the preceding failures apply, such as an MTU mismatch failure. This value is only applicable if the peer is using the pseudowire status signaling method to indicate faults.

pwNotForwarding — Pseudowire not forwarding

lacIngressFault Local — Attachment circuit RX fault

lacEgresssFault Local — Attachment circuit TX fault

psnIngressFault Local — PSN-facing PW RX fault

psnEgressFault Local — PSN-facing PW TX fault

pwFwdingStandby — Pseudowire in standby mode

LLF Admin State

Displays the Link Loss Forwarding administrative state.

LLF Oper State

Displays the Link Loss Forwarding operational state.

Standby Signaling Master

Indicates whether the parameter standby signaling master is enabled.

Hash Label

Indicates whether use of PW hash label is enabled.

Oper Hash Label

Indicates whether the MPLS packet originated by the node is using PW Hash label if the value displayed is Enabled. If the value displayed is Disabled, the MPLS packets originated by the node is not using Pseudowire Hash label.

Hash Lbl Sig Cap

Indicates whether PW hash label signaling is enabled.

base
Syntax

base

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays basic information about the service ID, including service type, description, and SAPs.

Output

The following output is an example of basic service information, and Output fields: service ID base describes the output fields.

Sample output
A:Dut-A# show service id 1101 base
===============================================================================
Service Basic Information
===============================================================================
Service Id        : 1101                Vpn Id            : 1101
Service Type      : Epipe
Description       : Default epipe description for service id 1101
Customer Id       : 1
Last Status Change: 07/07/2009 18:13:43
Last Mgmt Change  : 07/07/2009 14:39:14
Admin State       : Up                  Oper State        : Up
MTU               : 1514
Vc Switching      : False
SAP Count         : 1                   SDP Bind Count    : 1
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier                               Type         AdmMTU  OprMTU  Adm  Opr
-------------------------------------------------------------------------------
sap:lag-4:1101                           q-tag        9212    9212    Up   Up
sdp:1409:1101 S(10.20.1.4)               n/a          0       9186    Up   Up
===============================================================================
A:Dut-A#
Table 8. Output fields: service ID base
Label Description

Service Id

The service identifier.

Vpn Id

Specifies the VPN ID assigned to the service.

Service Type

The type of service: Epipe, VPLS

Description

Generic information about the service.

Customer Id

The customer identifier.

Last Mgmt Change

The date and time of the most recent management-initiated change to this customer.

Adm

The configured state of the service.

Oper

The operating state of the service.

Mtu

The largest frame size (in octets) that the service can handle.

Def. Mesh VC Id

This object is only valid in services that accept mesh SDP bindings. It is used to validate the VC ID portion of each mesh SDP binding defined in the service.

SAP Count

The number of SAPs defined on the service.

SDP Bind Count

The number of SDPs bound to the service.

Identifier

Specifies the service access (SAP) points.

Type

Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received.

AdmMTU

Specifies the configured largest service frame size (in octets) that can be transmitted, without requiring the packet to be fragmented.

PBB Tunnel Point

Specifies the endpoint in the B-VPLS environment where the Epipe terminates.

Admin MTU

Specifies the B-VPLS admin MTU.

Backbone-Flooding

Specifies whether the traffic is flooded in the B-VPLS for the destination instead of unicast. If the backbone destination MAC is in the B-VPLS FDB, it is unicast.

ISID

The 24-bit field carrying the service instance identifier associated with the frame. It is used at the destination PE as a demultiplexor field.

endpoint
Syntax

endpoint [endpoint-name]

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays service endpoint information.

Parameters
endpoint-name

Specifies the name of an existing endpoint for the service.

Output

The following output is an example of endpoint information, and Output fields: service ID endpoint describes the output fields.

Sample output
*A:Dut-A>show>service>id# endpoint

===============================================================================
Service 1501 endpoints
===============================================================================
Endpoint name                : coreSide
Description                  : (Not Specified)
Revert time                  : 0
Act Hold Delay               : 0
Standby Signaling Master     : true
Tx Active                    : 1413:1501
Tx Active Up Time            : 0d 03:46:25
Revert Time Count Down       : N/A
Tx Active Change Count       : 2
Last Tx Active Change        : 02/21/2011 13:07:12
-------------------------------------------------------------------------------
Members
-------------------------------------------------------------------------------
Spoke-sdp: 1413:1501 Prec:1                         Oper Status: Up
Spoke-sdp: 1613:1501 Prec:2                         Oper Status: Up
===============================================================================
Endpoint name                : accessSide
Description                  : (Not Specified)
Revert time                  : 0
Act Hold Delay               : 0
Standby Signaling Master     : false
Tx Active                    : lag-3:1501.1501
Tx Active Up Time            : 0d 03:46:52
Revert Time Count Down       : N/A
Tx Active Change Count       : 1
Last Tx Active Change        : 02/21/2011 13:06:45
-------------------------------------------------------------------------------
Members
-------------------------------------------------------------------------------
SAP      : lag-3:1501.1501                          Oper Status: Up
===============================================================================
===============================================================================
Table 9. Output fields: service ID endpoint
Label Description

Service endpoints

Endpoint name

Identifies the endpoint.

Revert time

Displays the revert time setting for the active spoke SDP.

Act Hold Delay

Not applicable.

Ignore Standby Signaling

Indicates whether standby signaling is ignored.

True — standby signaling is ignored

False — standby signaling is not ignored

Suppress Standby Signaling

Indicates whether standby signaling is suppressed.

True — standby signaling is suppressed

False — standby signaling is not suppressed

Tx Active

Identifies the actively transmitting spoke SDP.

Tx Active Up Time

Indicates the length of time that the active spoke SDP has been up.

Revert Time Count Down

Not applicable.

Tx Active Change Count

Indicates the number of times that there has been a change of active spoke SDPs.

Last Tx Active Change

Indicates the date and time when a different spoke SDP became the actively transmitting spoke SDP.

labels
Syntax

labels

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays the labels being used by the service.

Output

The following output is an example of service label information, and Output fields: service ID labels describes the output fields.

Sample output
*A:ALA-12# show service id 1 labels
============================================================================== 
Martini Service Labels                                                          
============================================================================== 
Svc Id     Sdp Id             Type I.Lbl        E.Lbl                           
------------------------------------------------------------------------------ 
1          10:1               Mesh 0            0                               
1          20:1               Mesh 0            0                               
1          30:1               Mesh 0            0                               
1          40:1               Mesh 130081       131061                          
1          60:1               Mesh 131019       131016                          
1          100:1              Mesh 0            0                               
------------------------------------------------------------------------------ 
Number of Bound SDPs : 6                                                       
------------------------------------------------------------------------------ 
*A:ALA-12#
Table 10. Output fields: service ID labels
Label Description

Svc Id

The service identifier.

Sdp Id

The SDP identifier.

Type

Indicates whether the SDP is a spoke or a mesh.

I. Lbl

The VC label used by the far-end device to send packets to this device in this service by the SDP.

E. Lbl

The VC label used by this device to send packets to the far-end device in this service by the SDP.

sap
Syntax

sap sap-id [detail]

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays information for the SAPs associated with the service. If no optional parameters are specified, a summary of all associated SAPs is displayed.

Parameters
sap-id

Specifies the ID that displays SAPs for the service in the form slot/mda/port[.channel]. See Common CLI command descriptions for command syntax.

interface interface-name

Displays information for the specified IP interface.

ip-address ip-address

Displays information associated with the specified IP address.

detail

Displays more information for the SAP.

Output

The following outputs are examples of SAP information, and Output fields: service ID SAP describes the output fields.

Sample output

*A:DUT-B_sasx>show>service# id 257 sap 1/1/3:64 detail

===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id         : 257
SAP                : 1/1/3:64                 Encap             : q-tag
Description        : (Not Specified)
Admin State        : Up                       Oper State        : Up
Flags              : None
Last Status Change : 05/19/2000 12:13:40
Last Mgmt Change   : 05/20/2000 11:00:53
Loopback Mode      : Internal                 No-svc-port used : 1/1/13
Loopback Src Addr  : 00:00:00:22:22:22 
Loopback Dst Addr  : 00:00:00:11:11:11 
Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100

Admin MTU          : 1518                     Oper MTU          : 1518
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
tod-suite          : None
Endpoint           : x

Acct. Pol          : None                     Collect Stats     : Disabled
Ignore Oper Down : Disabled

-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1                        Egress qos-policy : 1
-------------------------------------------------------------------------------
Sap Egress Policy (1)
-------------------------------------------------------------------------------
Scope              : Template
Remark             : False                    Remark Pol Id     : 2
Accounting         : frame-based
Description    : Default SAP egress QoS policy.
-------------------------------------------------------------------------------
Queue Rates and Rules
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        CIR          CIR Adpt Rule        PIR          PIR Adpt Rule
-------------------------------------------------------------------------------
Queue1          0              closest            max            closest
Queue2          0              closest            max            closest
Queue3          0              closest            max            closest
Queue4          0              closest            max            closest
Queue5          0              closest            max            closest
Queue6          0              closest            max            closest
Queue7          0              closest            max            closest
Queue8          0              closest            max            closest
-------------------------------------------------------------------------------
Parent Details
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId          Port       CIR Level      PIR Weight
-------------------------------------------------------------------------------
Queue1          True             1             1
Queue2          True             1             1
Queue3          True             1             1
Queue4          True             1             1
Queue5          True             1             1
Queue6          True             1             1
Queue7          True             1             1
Queue8          True             1             1
-------------------------------------------------------------------------------
High Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            70           90            75
Queue2          Down            70           90            75
Queue3          Down            70           90            75
Queue4          Down            70           90            75
Queue5          Down            70           90            75
Queue6          Down            70           90            75
Queue7          Down            70           90            75
Queue8          Down            70           90            75
-------------------------------------------------------------------------------
Low Slope
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId        State      Start-Avg(%)   Max-Avg(%)   Max-Prob(%)
-------------------------------------------------------------------------------
Queue1          Down            50           75            75
Queue2          Down            50           75            75
Queue3          Down            50           75            75
Queue4          Down            50           75            75
Queue5          Down            50           75            75
Queue6          Down            50           75            75
Queue7          Down            50           75            75
Queue8          Down            50           75            75
-------------------------------------------------------------------------------
Burst Sizes and Time Average Factor
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QueueId         CBS            MBS       Time Average Factor        Queue-Mgmt
-------------------------------------------------------------------------------
Queue1          def               def              7           default
Queue2          def               def              7           default
Queue3          def               def              7           default
Queue4          def               def              7           default
Queue5          def               def              7           default
Queue6          def               def              7           default
Queue7          def               def              7           default
Queue8          def               def              7           default
-------------------------------------------------------------------------------
Aggregate Policer (Not Available)
-------------------------------------------------------------------------------
rate               : n/a                      burst             : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4                     Meters Allocated   : 2
Classifiers Used     : 1                     Meters Used        : 1
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Stats:          5726350                 8589525000
Egress Stats:           0                       0
-------------------------------------------------------------------------------
Sap per Meter stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Ingress Meter 1 (Unicast)
For. InProf           : 3                       4500
For. OutProf          : 5733754                 8600631000
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
                        Packets                 Octets

Egress Queue 1 (be)
Fwd Stats            :  56935                   86541200
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 2 (l2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 3 (af)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 4 (l1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 5 (h2)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 6 (ef)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 7 (h1)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0

Egress Queue 8 (nc)
Fwd Stats            :  0                       0
Drop InProf          :  0                       0
Drop OutProf         :  0                       0
===============================================================================

Sample output for 7210 SAS-R6 and 7210 SAS-R12
*A:Dut-A# show service id 10 sap 5/1/1:800 detail 
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id         : 10                       
SAP                : 5/1/1:800                Encap             : q-tag
Description        : (Not Specified)
Admin State        : Up                       Oper State        : Down
Flags              : PortOperDown
Last Status Change : 11/07/2017 04:48:25      
Last Mgmt Change   : 11/07/2017 05:02:47      
Dot1Q Ethertype    : 0x8100                   QinQ Ethertype    : 0x8100
Split Horizon Group: (Not Specified)
Admin MTU          : 1518                     Oper MTU          : 1518
Ingr IP Fltr-Id    : n/a                      Egr IP Fltr-Id    : n/a
Ingr Mac Fltr-Id   : n/a                      Egr Mac Fltr-Id   : n/a
Ingr IPv6 Fltr-Id  : n/a                      Egr IPv6 Fltr-Id  : n/a
BGP IPv4 FlowSpec  : Disabled
BGP IPv6 FlowSpec  : Disabled
tod-suite          : None                     
Egr Agg Rate CIR   : 0                        Egr Agg Rate PIR  : max
                                              Limit Unused BW   : Disabled
Acct. Pol          : None                     Collect Stats     : Disabled
Anti Spoofing      : None                     Dynamic Hosts     : Enabled
Oper Group         : (none)                   Monitor Oper Grp  : (none)
Host Lockout Plcy  : n/a                      
Lag Link Map Prof  : (none)                   
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 17                       Egress qos-policy : 1
Table-based        : enabled
-------------------------------------------------------------------------------
Aggregate Policer
-------------------------------------------------------------------------------
Rate               : n/a                      Burst             : n/a
-------------------------------------------------------------------------------
Egress Aggregate Meter
-------------------------------------------------------------------------------
Rate               : n/a                      Burst             : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 60                    Meters Allocated   : 30
Classifiers Used     : 9                     Meters Used        : 8
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Stats:          0                       0                        
Egress Stats:           0                       0                        
Ingress Drop Stats:     0                       0                        
 
Extra-Tag Drop Stats:   n/a                     n/a                      
-------------------------------------------------------------------------------
Sap per Meter stats (in/out counter mode)
-------------------------------------------------------------------------------
                        Packets                 Octets
Ingress Meter 1
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 2
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 3
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 4
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 5
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 6
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 7
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
 
Ingress Meter 8
For. InProf           : 0                       0                        
For. OutProf          : 0                       0                        
===============================================================================
Table 11. Output fields: service ID SAP
Label Description

Service Id

The service identifier.

SAP

The SAP and qtag.

Encap

The encapsulation type of the SAP.

Ethertype

Specifies an Ethernet type II Ethertype value.

Admin State

The administrative state of the SAP.

Oper State

The operating state of the SAP.

Flags

Specifies the conditions that affect the operating status of this SAP.

Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapEgressQoSMismatch,RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, ServiceMTUTooSmall, SapIngressNamedPoolMismatch, SapEgressNamedPoolMismatch, NoSapEpipeRingNode.

Last Status Change

The time of the most recent operating status change to this SAP.

Last Mgmt Change

The time of the most recent management-initiated change to this SAP.

Admin MTU

The configured largest service frame size (in octets) that can be transmitted through to the far-end router, without requiring the packet to be fragmented.

Oper MTU

The actual largest service frame size (in octets) that can be transmitted through to the far-end router, without requiring the packet to be fragmented.

Ingress qos-policy

The ingress QoS policy ID assigned to the SAP.

Egress qos-policy

The egress QoS policy ID assigned to the SAP.

Ingress Filter-Id

The ingress filter policy ID assigned to the SAP.

Egress Filter-Id

The egress filter policy ID assigned to the SAP.

Acct. Pol

The accounting policy ID assigned to the SAP.

Collect Stats

Specifies whether collect stats is enabled.

Ignore Oper Down

Displays whether the user has enabled or disabled the ignore-oper-down parameter.

LLF Admin State

Displays the Link Loss Forwarding administrative state.

LLF Oper State

Displays the Link Loss Forwarding operational state.

Loopback Mode

Displays the Ethernet port loop back mode.

Loopback Src Addr

Displays the configured loopback source address.

Loopback Dst Addr

Displays the configured loopback destination address.

No-svc-port used

Displays the port ID of the port on which no service is configured.

This port is used for the port loopback with MAC swap functionality.

Loopback Mode

Displays the Ethernet port loopback mode.

Loopback Src Addr

Displays the configured loopback source address.

Loopback Dst Addr

Displays the configured loopback destination address.

No-svc-port used

Displays the port ID of the port on which no service is configured. This port is used for the port loop back with MAC swap functionality.

Table-based

Indicates the use of table-based resource classification: Enabled (table-based) or Disabled (CAM-based).

sdp
Syntax

sdp [sdp-id | far-end ip-addr] [detail]

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays information for the SDPs associated with the service.

If no optional parameters are specified, a summary of all associated SDPs is displayed.

Parameters
sdp-id

Displays information only for the specified SDP ID.

Default

All SDPs.

Values

1 to 17407

far-end ip-addr

Displays only SDPs matching the specified far-end IP address.

Default

SDPs with any far-end IP address.

detail

Displays detailed SDP information.

Output

Output fields: service ID SDP describes the show service ID SDP output fields.

Sample output
Table 12. Output fields: service ID SDP
Label Description

Sdp Id

The SDP identifier.

Type

Indicates whether the SDP is a spoke or a mesh.

Split Horizon Group

Name of the split horizon group that the SDP belongs to.

VC Type

The VC type, ether, vlan, or vpls.

VC Tag

The explicit dot1q value used when encapsulating to the SDP far end.

I. Lbl

The VC label used by the far-end device to send packets to this device in this service by the SDP.

Admin Path MTU

The operating path MTU of the SDP is equal to the admin path MTU (when one is set) or the dynamically computed tunnel MTU, when no admin path MTU is set (the default case).

Oper Path MTU

The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.

Far End

Specifies the IP address of the remote end of the MPLS tunnel defined by this SDP.

Delivery

Specifies the type of delivery used by the SDP: MPLS.

Admin State

The administrative state of this SDP.

Oper State

The current state of this SDP.

Ingress Label

The label used by the far-end device to send packets to this device in this service by this SDP.

Egress Label

The label used by this device to send packets to the far-end device in this service by the SDP.

Last Changed

The date and time of the most recent change to the SDP.

Signaling

Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP.

Admin State

The administrative state of the keepalive process.

Oper State

The operational state of the keepalive process.

Hello Time

Transmission frequency of the SDP echo request messages.

Max Drop Count

Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault.

Hello Msg Len

The length of the SDP echo request messages transmitted on this SDP.

Hold Down Time

Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state.

I. Fwd. Pkts.

Specifies the number of forwarded ingress packets.

I. Dro. Pkts

Specifies the number of dropped ingress packets.

E. Fwd. Pkts.

Specifies the number of forwarded egress packets.

Associated LSP List

When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the Far End field.

split-horizon-group
Syntax

split-horizon-group [group-name]

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays service split horizon groups.

Output

The following output is an example of split horizon group information, and Output fields: split horizon group describes the output fields.

Sample output
*A:7210-SAS>show>service# id 1 split-horizon-group

===============================================================================
Service: Split Horizon Group
===============================================================================
Name                               Description
-------------------------------------------------------------------------------
    access
-------------------------------------------------------------------------------
R = Residential Split Horizon Group
A = Auto Created Split Horizon Group
No. of Split Horizon Groups: 1
===============================================================================
*A:7210-SAS>show>service# id 1 split-horizon-group access

===============================================================================
Service: Split Horizon Group
===============================================================================
Name                               Description
-------------------------------------------------------------------------------
    access
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
R = Residential Split Horizon Group
SAPs Associated : 0                SDPs Associated : 0
*A:7210-SAS>show>service#
Table 13. Output fields: split horizon group
Label Description

Name

The name of the split horizon group. When preceded by ‟R”, the group is a residential split horizon group.

Description

A description of the split horizon group as configured by the user.

Associations

A list of SAPs and SDPs associated with the split horizon group.

stp
Syntax

stp [detail]

Context

show>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command displays information for the spanning tree protocol instance for the service.

Parameters
detail

Displays more information.

Output

The following output is an example of STP information, and Output fields: show service ID STP describes the output fields.

Sample output
A:Dut-A>show>service>id# stp
===============================================================================
Stp info, Service 305
===============================================================================
Bridge Id          : 00:0d.00:20:ab:cd:00:01  Top. Change Count : 5
Root Bridge        : This Bridge              Stp Oper State    : Up
Primary Bridge     : N/A                      Topology Change   : Inactive
Mode               : Rstp                     Last Top. Change  : 0d 08:35:16
Vcp Active Prot.   : N/A
Root Port          : N/A                      External RPC      : 0
===============================================================================
Stp port info
===============================================================================
Sap/Sdp Id         Oper-     Port-      Port-       Port-  Oper-  Link-  Active
                   State     Role       State       Num    Edge   Type   Prot.
-------------------------------------------------------------------------------
1/1/16:305         Up        Designated Forward     2048   False  Pt-pt  Rstp
lag-4:305          Up        Designated Forward     2000   False  Pt-pt  Rstp
1217:305           Up        N/A        Forward     2049   N/A    Pt-pt  N/A
1317:305           Up        N/A        Forward     2050   N/A    Pt-pt  N/A
1417:305           Up        N/A        Forward     2051   N/A    Pt-pt  N/A
1617:305           Pruned    N/A        Discard     2052   N/A    Pt-pt  N/A
===============================================================================
A:Dut-A>show>service>id# 


A:Dut-A>show>service>id# stp detail
===============================================================================
Spanning Tree Information
===============================================================================
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state    : Up                       Core Connectivity : Down
Stp Admin State    : Up                       Stp Oper State    : Up
Mode               : Rstp                     Vcp Active Prot.  : N/A

Bridge Id          : 00:0d.00:20:ab:cd:00:01  Bridge Instance Id: 13
Bridge Priority    : 0                        Tx Hold Count     : 6
Topology Change    : Inactive                 Bridge Hello Time : 2
Last Top. Change   : 0d 08:35:29              Bridge Max Age    : 20
Top. Change Count  : 5                        Bridge Fwd Delay  : 15
MST region revision: 0                        Bridge max hops   : 20
MST region name    :

Root Bridge        : This Bridge
Primary Bridge     : N/A

Root Path Cost     : 0                        Root Forward Delay: 15
Rcvd Hello Time    : 2                        Root Max Age      : 20
Root Priority      : 13                       Root Port         : N/A
-------------------------------------------------------------------------------
Spanning Tree Sap/Spoke SDP Specifics
-------------------------------------------------------------------------------
SAP Identifier     : 1/1/16:305               Stp Admin State   : Up
Port Role          : Designated               Port State        : Forwarding
Port Number        : 2048                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : False
Link Type          : Pt-pt                    BPDU Encap        : PVST
Root Guard         : Disabled                 Active Protocol   : Rstp
Last BPDU from     : 80:04.00:0a:1b:2c:3d:4e
CIST Desig Bridge  : This Bridge              Designated Port   : 34816
Forward transitions: 5                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 29                       RST BPDUs tx      : 23488
MST BPDUs rcvd     : 0                        MST BPDUs tx      : 0

SAP Identifier     : lag-4:305                Stp Admin State   : Up
Port Role          : Designated               Port State        : Forwarding
Port Number        : 2000                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : False
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : Rstp
Last BPDU from     : 80:04.00:0a:1b:2c:3d:4e
CIST Desig Bridge  : This Bridge              Designated Port   : 34768
Forward transitions: 4                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 23                       RST BPDUs tx      : 23454
MST BPDUs rcvd     : 0                        MST BPDUs tx      : 0

SDP Identifier     : 1217:305                 Stp Admin State   : Down
Port Role          : N/A                      Port State        : Forwarding
Port Number        : 2049                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A
Designated Bridge  : N/A                      Designated Port Id: 0
Fwd Transitions    : 0                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0

SDP Identifier     : 1317:305                 Stp Admin State   : Down
Port Role          : N/A                      Port State        : Forwarding
Port Number        : 2050                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A
Designated Bridge  : N/A                      Designated Port Id: 0
Fwd Transitions    : 0                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0

SDP Identifier     : 1417:305                 Stp Admin State   : Down
Port Role          : N/A                      Port State        : Forwarding
Port Number        : 2051                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A
Designated Bridge  : N/A                      Designated Port Id: 0
Fwd Transitions    : 1                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0

SDP Identifier     : 1617:305                 Stp Admin State   : Down
Port Role          : N/A                      Port State        : Discarding
Port Number        : 2052                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : N/A
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : N/A
Last BPDU from     : N/A
Designated Bridge  : N/A                      Designated Port Id: 0
Fwd Transitions    : 0                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
===============================================================================
A:Dut-A>show>service>id#

*7210-SAS>show>service>id# stp detail

===============================================================================
Spanning Tree Information
===============================================================================

-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state    : Up                       Core Connectivity : Down
Stp Admin State    : Up                       Stp Oper State    : Up
Mode               : Mstp                     Vcp Active Prot.  : N/A

Bridge Id          : 80:00.00:25:ba:04:66:a0  Bridge Instance Id: 0
Bridge Priority    : 32768                    Tx Hold Count     : 6
Topology Change    : Inactive                 Bridge Hello Time : 2
Last Top. Change   : 0d 02:54:16              Bridge Max Age    : 20
Top. Change Count  : 27                       Bridge Fwd Delay  : 15

Root Bridge        : 40:00.7c:20:64:ac:ff:63
Primary Bridge     : N/A

Root Path Cost     : 10                       Root Forward Delay: 15
Rcvd Hello Time    : 2                        Root Max Age      : 20
Root Priority      : 16384                    Root Port         : 2048

MSTP info for CIST :
Regional Root      : 80:00.7c:20:64:ad:04:5f  Root Port         : 2048
Internal RPC       : 10                       Remaining Hopcount: 19
MSTP info for MSTI 1 :
Regional Root      : This Bridge              Root Port         : N/A
Internal RPC       : 0                        Remaining Hopcount: 20
MSTP info for MSTI 2 :
Regional Root      : 00:02.7c:20:64:ad:04:5f  Root Port         : 2048
Internal RPC       : 10                       Remaining Hopcount: 19


-------------------------------------------------------------------------------
Spanning Tree Sap Specifics
-------------------------------------------------------------------------------
SAP Identifier     : 1/1/7:0                  Stp Admin State   : Up
Port Role          : Root                     Port State        : Forwarding
Port Number        : 2048                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : False
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : Mstp
Last BPDU from     : 80:00.7c:20:64:ad:04:5f  Inside Mst Region : True
CIST Desig Bridge  : 80:00.7c:20:64:ad:04:5f  Designated Port   : 34816
MSTI 1 Port Prio   : 128                      Port Path Cost    : 10
MSTI 1 Desig Brid  : This Bridge              Designated Port   : 34816
MSTI 2 Port Prio   : 128                      Port Path Cost    : 10
MSTI 2 Desig Brid  : 00:02.7c:20:64:ad:04:5f  Designated Port   : 34816
Forward transitions: 17                       Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 7310                     MST BPDUs tx      : 7277

SAP Identifier     : 1/1/8:0                  Stp Admin State   : Up
Port Role          : Alternate                Port State        : Discarding
Port Number        : 2049                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : False
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : Mstp
Last BPDU from     : 80:00.7c:20:64:ad:04:5f  Inside Mst Region : True
CIST Desig Bridge  : 80:00.7c:20:64:ad:04:5f  Designated Port   : 34817
MSTI 1 Port Prio   : 128                      Port Path Cost    : 10
MSTI 1 Desig Brid  : This Bridge              Designated Port   : 34817
MSTI 2 Port Prio   : 128                      Port Path Cost    : 10
MSTI 2 Desig Brid  : 00:02.7c:20:64:ad:04:5f  Designated Port   : 34817
Forward transitions: 14                       Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 7326                     MST BPDUs tx      : 7307

SAP Identifier     : 1/1/9:0                  Stp Admin State   : Up
Port Role          : Designated               Port State        : Forwarding
Port Number        : 2050                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : True
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : Mstp
Last BPDU from     : N/A                      Inside Mst Region : True
CIST Desig Bridge  : This Bridge              Designated Port   : 34818
MSTI 1 Port Prio   : 128                      Port Path Cost    : 10
MSTI 1 Desig Brid  : This Bridge              Designated Port   : 34818
MSTI 2 Port Prio   : 128                      Port Path Cost    : 10
MSTI 2 Desig Brid  : This Bridge              Designated Port   : 34818
Forward transitions: 2                        Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 0                        MST BPDUs tx      : 7415

SAP Identifier     : 1/1/25:0                 Stp Admin State   : Up
Port Role          : Alternate                Port State        : Discarding
Port Number        : 2051                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : False
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : Mstp
Last BPDU from     : 80:00.7c:20:64:ad:04:5f  Inside Mst Region : True
CIST Desig Bridge  : 80:00.7c:20:64:ad:04:5f  Designated Port   : 34820
MSTI 1 Port Prio   : 128                      Port Path Cost    : 10
MSTI 1 Desig Brid  : This Bridge              Designated Port   : 34819
MSTI 2 Port Prio   : 128                      Port Path Cost    : 10
MSTI 2 Desig Brid  : 00:02.7c:20:64:ad:04:5f  Designated Port   : 34820
Forward transitions: 10                       Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 7329                     MST BPDUs tx      : 7303

SAP Identifier     : lag-1:0                  Stp Admin State   : Up
Port Role          : Alternate                Port State        : Discarding
Port Number        : 2052                     Port Priority     : 128
Port Path Cost     : 10                       Auto Edge         : Enabled
Admin Edge         : Disabled                 Oper Edge         : False
Link Type          : Pt-pt                    BPDU Encap        : Dot1d
Root Guard         : Disabled                 Active Protocol   : Mstp
Last BPDU from     : 80:00.7c:20:64:ad:04:5f  Inside Mst Region : True
CIST Desig Bridge  : 80:00.7c:20:64:ad:04:5f  Designated Port   : 34822
MSTI 1 Port Prio   : 128                      Port Path Cost    : 10
MSTI 1 Desig Brid  : This Bridge              Designated Port   : 34820
MSTI 2 Port Prio   : 128                      Port Path Cost    : 10
MSTI 2 Desig Brid  : 00:02.7c:20:64:ad:04:5f  Designated Port   : 34822
Forward transitions: 11                       Bad BPDUs rcvd    : 0
Cfg BPDUs rcvd     : 0                        Cfg BPDUs tx      : 0
TCN BPDUs rcvd     : 0                        TCN BPDUs tx      : 0
RST BPDUs rcvd     : 0                        RST BPDUs tx      : 0
MST BPDUs rcvd     : 7322                     MST BPDUs tx      : 7299

===============================================================================
Table 14. Output fields: show service ID STP
Label Description

RSTP Admin State

Indicates the administrative state of the Rapid Spanning Tree Protocol instance associated with this service.

Core Connectivity

Indicates the connectivity status to the core.

RSTP Oper State

Indicates the operational state of the Rapid Spanning Tree Protocol instance associated with this service. This field is applicable only when STP is enabled on the router.

Bridge-id

Specifies the MAC address used to identify this bridge in the network.

Hold Time

Specifies the interval length during which no more than two Configuration BPDUs shall be transmitted by this bridge.

Bridge fwd delay

Specifies how fast a bridge changes its state when moving toward the forwarding state.

Bridge Hello time

Specifies the amount of time between the transmission of Configuration BPDUs.

Bridge max age

Specifies the maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded. This is the actual value that this bridge is currently using.

Bridge priority

Defines the priority of the Spanning Tree Protocol instance associated with this service.

Topology change

Specifies whether a topology change is currently in progress.

Last Top. change

Specifies the time (in hundredths of a second) after the last time a topology change was detected by the Spanning Tree Protocol instance associated with this service.

Top. change count

Specifies the total number of topology changes detected by the Spanning Tree Protocol instance associated with this service after the management entity was last reset or initialized.

Root bridge-id

Specifies the bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol instance associated with this service. This value is used as the Root Identifier parameter in all Configuration BPDUs originated by this node.

Root path cost

Specifies the cost of the path to the root bridge as seen from this bridge.

Root forward delay

Specifies how fast the root changes its state when moving toward the forwarding state.

hello time

Specifies the amount of time between the transmission of configuration BPDUs.

Root max age

Specifies the maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded.

Root priority

This object specifies the priority of the bridge that is currently selected as root-bridge for the network.

Root port

Specifies the port number of the port which provides the lowest cost path from this bridge to the root bridge.

SAP Identifier

The ID of the access port where this SAP is defined.

RSTP State

The operational state of RSTP.

STP Port State

Specifies the port identifier of the port on the designated bridge for this port's segment.

BPDU encap

Specifies the type of encapsulation used on BPDUs sent out and received on this SAP.

Port Number

Specifies the value of the port number field which is contained in the least significant 12 bits of the 16-bit port ID associated with this SAP.

Priority

Specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit port ID associated with this SAP.

Cost

Specifies the contribution of this port to the path cost of paths toward the spanning tree root which include this port.

Fast Start

Specifies whether Fast Start is enabled on this SAP.

Designated Port

Specifies the port identifier of the port on the designated bridge for this port's segment.

Designated Bridge

Specifies the bridge identifier of the bridge that this port considers to be the designated bridge for this port's segment.

Clear commands

id
Syntax

id service-id

Context

clear>service

clear>service>statistics

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears commands for a specific service.

Parameters
service-id

Specifies the ID that uniquely identifies a service.

Values

service-id: 1 to 214748364

svc-name: A string up to 64 characters.

spoke-sdp
Syntax

spoke-sdp sdp-id:vc-id ingress-vc-label

Context

clear>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears and resets the spoke-SDP bindings for the service.

Parameters
sdp-id

Specifies the spoke-SDP ID to be reset.

Values

1 to 17407

vc-id

Specifies the virtual circuit ID on the SDP ID to be reset.

Values

1 to 4294967295

ingress-vc-label

Keyword that specifies to clear the ingress VC label.

sap
Syntax

sap sap-id {all | counters | stp}

Context

clear>service>statistics

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears SAP statistics for a SAP.

Parameters
sap-id

Specifies the physical port identifier portion of the SAP definition. See Common CLI command descriptions for command syntax.

all

Clears all SAP queue statistics and STP statistics.

counters

Clears all queue statistics associated with the SAP.

stp

Clears all STP statistics associated with the SAP.

l2pt

Clears all L2PT statistics associated with the SDP.

sdp
Syntax

sdp sdp-id keep-alive

Context

clear>service>statistics

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears keepalive statistics associated with the SDP ID.

Parameters
sdp-id

Specifies the SDP ID for which to clear keepalive statistics.

Values

1 to 17407

counters
Syntax

counters

Context

clear>service>statistics>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears all traffic queue counters associated with the service ID.

spoke-sdp
Syntax

spoke-sdp sdp-id[:vc-id] {all | counters | stp}

Context

clear>service>statistics>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears statistics for the spoke-SDP bound to the service.

Parameters
sdp-id

Specifies the spoke-SDP ID for which to clear statistics.

Values

1 to 17407

vc-id

Specifies the virtual circuit ID on the SDP ID to be reset.

Values

1 to 4294967295

all

Clears all queue statistics and STP statistics associated with the SDP.

counters

Clears all queue statistics associated with the SDP.

stp

Clears all STP statistics associated with the SDP.

stp
Syntax

stp

Context

clear>service>statistics>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command clears all spanning tree statistics for the service ID.

statistics
Syntax

statistics

Context

clear>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

Commands in this context clear statistics for a specific service entity.

Debug commands

id
Syntax

id service-id

Context

debug>service

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command debugs commands for a specific service.

Parameters
service-id

Specifies the ID that uniquely identifies a service.

sap
Syntax

[no] sap sap-id

Context

debug>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables debugging for a particular SAP.

Parameters
sap-id

Specifies the SAP ID.

event-type
Syntax

[no] event-type {arp | config-change | oper-status-change}

Context

debug>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables a particular debugging event type.

The no form of this command disables the event type debugging.

Parameters
arp

Displays ARP events.

config-change

Debugs configuration change events.

svc-oper-status-change

Debugs service operational status changes.

Output

The following output is an example of event type debugging information.

Sample output
A:bksim180# debug service id 1000 sap 1/7/1 event-type arp 
DEBUG OUTPUT show on CLI is as follows:
3 2008/11/17 18:13:24.35 UTC MINOR: DEBUG #2001 Base Service 1000 SAP 1/7/1 
"Service 1000 SAP 1/7/1: 
RX: ARP_REQUEST (0x0001)
hwType     : 0x0001
prType     : 0x0800
hwLength   : 0x06
prLength   : 0x04
srcMac     : 8c:c7:01:07:00:03
destMac    : 00:00:00:00:00:00
srcIp      : 239.1.1.2
destIp     : 239.1.1.1
"

4 2008/11/17 18:13:24.35 UTC MINOR: DEBUG #2001 Base Service 1000 SAP 1/7/1 
"Service 1000 SAP 1/7/1: 
TX: ARP_RESPONSE (0x0002)
hwType     : 0x0001
prType     : 0x0800
hwLength   : 0x06
prLength   : 0x04
srcMac     : 00:03:0a:0a:0a:0a
destMac    : 8c:c7:01:07:00:03
srcIp      : 239.1.1.1
destIp     : 239.1.1.2
"
sdp
Syntax

[no] sdp sdp-id:vc-id

Context

debug>service>id

Platforms

Supported on all 7210 SAS platforms as described in this document

Description

This command enables debugging for a particular SDP.

Parameters
sdp-id

Specifies the SDP ID.