c Commands
ca-profile
ca-profile
Syntax
ca-profile
ca-profile name [association]
Context
[Tree] (show>certificate ca-profile)
Full Context
show certificate ca-profile
Description
This command shows certificate-authority profile information.
Parameters
- name
-
Specifies the name of the Certificate Authority (CA) profile.
- association
-
Displays associated CA profiles.
Platforms
All
cache
cache
Syntax
cache [peer ip-address] [group ip-address] [source ip-address] [originrp ip-address]
Context
[Tree] (clear>router>msdp cache)
Full Context
clear router msdp cache
Description
This command clears the MSDP cache.
Parameters
- peer ip-address
-
Clears the cache of the IP address of the peer to which Multicast Source Discovery protocol (MSDP) source-active (SA) requests for groups matching this entry's group range were sent.
- group ip-address
-
Clears the group IP address of the SA entry.
- source ip-address
-
Clears the source IP address of the SA entry.
- originrp ip-address
-
Clears the origin rendezvous point (RP) address type of the SA entry.
Platforms
All
cache
Syntax
cache aggregate {src-dst-proto | src-dst-proto-port} family {ipv4 | ipv6}
cache all family {ipv4 | ipv6}
Context
[Tree] (tools>dump>cflowd cache)
Full Context
tools dump cflowd cache
Description
This command displays the contents of the cflowd active cache. This information can be displayed either in raw form where every flow entry is displayed or in an aggregated form.
Tools Dump cflowd Cache Output Fields describes the cflowd cache output fields.
Label |
Description |
---|---|
Proto/Protocol |
Displays the IPv4 or IPv6 protocol type |
Source Address/Src-IP |
Displays the source IP address of the flow (IPv4 or IPv6) |
Destination Address/Dst-IP |
Displays the destination IP address of the flow (IPv4 or IPv6) |
Intf/Ingr |
Displays the ingress interface associated with the sampled flow (only displayed with the raw (all) output) |
Intf/Egr |
Displays the egress interface associated with the sampled flow (only displayed with the raw (all) output) |
S-Port |
Displays the source protocol port number |
D-Port |
Displays the destination protocol port number |
Pkt-Cnt |
Displays the total number of packets sampled for the associated flow |
Byte-Cnt |
Displays the total number of bytes of traffic sampled for the associated flow |
Start-Time |
Displays the system time when the first packet was sampled for the associated flow |
Flags |
Displays the IP flag value from the sampled IP flow header (only displayed with the raw (all) output) |
ToS |
Displays the ToS byte values from the sampled IP flow header (only displayed with the raw (all) output) |
(Src) Mask |
Displays the IP route mask for the route to the flow source IP address associated with the flow (only displayed with the raw (all) output) |
(Dst) Mask |
Displays the IP route mask for the route to the flow destination IP address associated with the flow (only displayed with the raw (all) output) |
(Src) AS |
Displays the ASN associated with the route to the flow source IP address associated with the flow (only displayed with the raw (all) output) |
(Dst) AS |
Displays the ASN associated with the route to the flow destination IP address associated with the flow (only displayed with the raw (all) output) |
vRtr-ID |
Displays the Virtual Router ID associated with the reported IP flow (only displayed with the raw (all) output) |
Parameters
- aggregate
-
Displays the aggregated active cache flow data.
- family
-
Specifies which IP address family flow data should be displayed.
- all
-
Displays the raw active cache flow data with no aggregation.
Platforms
All
cache-contents
cache-contents
Syntax
cache-contents [isa mda-id/esa-vm-id] url file-url
Context
[Tree] (tools>dump>app-assure>group>ipassist cache-contents)
Full Context
tools dump application-assurance group ip-identification-assist cache-contents
Description
This command dumps the cache contents generated by the IP identification assist feature into a local or remote destination.
Parameters
- isa mda-id
-
Specifies the slot and MDA of the ISA in the format slot/mda.
- isa esa-vm-id
-
Specifies the ESA and ESA VM in the format esa-esa-id/vm-id.
- url file-url
- Specifies a local or remote destination to which the cache content output is directed.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
Use the following command to direct the cache contents generated by the IP identification assist feature to a remote destination.
tools dump application-assurance group 1 ip-identification-assist cache-contents isa 1/1 url ftp://exuser:expassword@192.0.2.1/tmp/sample-cache
Sample
Output===============================================================================
Application-Assurance Group 1 ip-identification-assist cache contents
===============================================================================
Writing to file ftp://exuser:expassword@192.0.2.1/tmp/sample-cache_1_1.ip-ident-assist-cache ...
File closed
-rw-r--r-- 1 exuser exuser 16553 Aug 24 09:22 sample-cache_1_1.ip-ident-assist-cach
calculate-maps
calculate-maps
Syntax
calculate-maps router router-instance subscriber-type nat-sub-type prefix ip-prefix/length
Context
[Tree] (tools>perform>nat>deterministic calculate-maps)
Full Context
tools perform nat deterministic calculate-maps
Description
This command allows the operator to reveal the auto-mappings before they are created in the system, while the inside prefix is still out of service (in a shutdown administrative state). Based on the auto-mapping results, the user can decide to use the auto-mapping and operationalize the prefix (no shutdown command), or to use custom mappings.
The inside IP addresses for deterministic subscribers and for 1:1 protocol agnostic subscribers can be mapped to outside IP addresses in the following ways:
-
Automatically by the system. By enabling the deterministic prefix (no shutdown command), the system will automatically create map commands and sequentially map subscribers into outside IP address space.
-
Manually by the operator by configuring the map commands. This gives the operator control over mappings beyond the sequential auto-mapping.
Parameters
- router-instance
-
Specifies the inside router name or VPRN service instance where the deterministic prefix resides.
- nat-sub-type
-
Specifies the NAT subscriber type.
- ip-prefix/length
-
Specifies the inside prefix containing IP addresses for which mapping is sought. The IP prefix is IPv4 family type for classic LSN subscriber and IPv6 family type for a DS-Lite subscriber.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
call-trace
call-trace
Syntax
call-trace
Context
[Tree] (show call-trace)
Full Context
show call-trace
Description
Commands in this context display information related to the call-trace module.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
call-trace
Syntax
call-trace
Context
[Tree] (clear call-trace)
Full Context
clear call-trace
Description
This command clears call trace jobs.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
cam-utilization
cam-utilization
Syntax
cam-utilization [card slot-number]
Context
[Tree] (tools>dump>filter cam-utilization)
Full Context
tools dump filter cam-utilization
Description
This command, when used without parameters, specifies the utilization per CAM table for line card ACL filters per FP for FP4 based cards in the system. Optionally, the card number can be provided as a parameter to limit the output to a single card.
Parameters
- slot-number
-
Specifies the IOM slot number.
Platforms
All
Output
The following output is an example of CAM utilization information for filters.
Sample Output*A:7750# tools dump filter cam-utilization
============================================
Filter Cam Utilization
============================================
Slot FP Dir Type Cam Utilization %
--------------------------------------------
2 1 Ing ip-mac 0
2 1 Egr ip-mac 100
2 1 Ing ipv6 0
2 1 Egr ipv6 0
============================================
candidate
candidate
Syntax
candidate
Context
[Tree] (show>system candidate)
Full Context
show system candidate
Description
This command shows classic CLI candidate configuration information.
This command is not available in the MD-CLI. Use the MD-CLI info command in a configuration region.
Platforms
All
Output
The following output is an example of candidate information, and Candidate Output Fields describes the output fields.
Sample Output*A:bksim3107# show system candidate
===============================================================================
Candidate Config Information
===============================================================================
Candidate configuration state : modified
Num editors/viewers : 0
Candidate cfg exclusive locked : no
Last commit state : revert-failed
Last commit time : 10/23/2012 17:21:47
Checkpoint created with last commit : yes
Scheduled revert time : N/A
Last commit revert time : 10/23/2012 17:22:47
===============================================================================
Users in edit-cfg mode
===============================================================================
Username Type (from)
===============================================================================
admin Console
Joris Telnet (192.0.2.239)
===============================================================================
Label |
Description |
---|---|
Candidate configuration state |
• empty — indicates there are no uncommitted changes in the candidate config • modified — indicates there are uncommitted changes in the candidate config • unconfirmed — indicates there are no uncommitted changes in the candidate config but the result of the last commit will be auto-reverted unless it is confirmed before the timeout expires |
Num editors/viewers |
Displays the number of CLI sessions currently in edit-cfg mode |
Candidate cfg exclusive locked |
Indicates if a user has exclusively locked the candidate using the candidate edit exclusive command |
Last commit state |
• none — indicates there have been no commits since the last reboot of the node • in-progress — indicates the system is currently committing the candidate config • success — indicates the last commit finished successfully • revert-pending — indicates the last commit finished successfully but has not been confirmed yet, and will be auto-reverted if it is not confirmed before the timeout expires • failed — indicates the last commit failed and has been undone • revert-in-progress — indicates the last commit finished successfully but was not confirmed in time and is currently being reverted • reverted — indicates the last commit finished successfully but was not confirmed in time and has been reverted • revert-failed — indicates the last commit finished successfully but was not confirmed in time and the system attempted to revert it but failed |
Last commit time |
Displays the time at which the last commit attempt was started |
Checkpoint created with last commit |
Indicates if a rollback checkpoint was created after the previous commit completed |
Scheduled revert time |
Indicates the currently scheduled auto-revert time based on the confirmed option being used with a candidate commit |
Last commit revert time |
Displays the time the commit was last reverted |
Users in edit-cfg mode |
Lists all the user sessions that are currently in edit-cfg mode |
Type (from) |
Indicates the type of session (such as Console, Telnet, and so on) and also the source of the session (such as the source IP address of the remote host) |
capabilities
capabilities
Syntax
capabilities [system-id | lsp-id] [level level]
Context
[Tree] (show>router>isis capabilities)
Full Context
show router isis capabilities
Description
This command displays the IS-IS capability information.
Parameters
- system-id
-
Only the LSPs related to the specified system-id are listed.
- lsp-id
-
Only the specified LSP is listed.
- level
-
Specifies the interface level (1, 2, or 1 and 2).
Platforms
All
Output
The following output is an example of IS-IS capability information, and IS-IS Capability Information Output Fields describes the output fields.
Sample Output*A:Dut-B# show router isis 0 capabilities
===============================================================================
Rtr Base ISIS Instance 0 Capabilities
===============================================================================
Displaying Level 1 capabilities
-------------------------------------------------------------------------------
LSP ID : Dut-B.00-00
Router Cap : 10.20.1.2, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:10001
SR Alg: metric based SPF, 128
Node MSD Cap: BMI : 12 ERLD : 15
FAD Sub-Tlv:
Flex-Algorithm : 128
Metric-Type : delay
Calculation-Type : 0
Priority : 100
Flags: M
LSP ID : Dut-D.00-00
Router Cap : 10.20.1.4, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:10001
SR Alg: metric based SPF, 128
Node MSD Cap: BMI : 12 ERLD : 15
FAD Sub-Tlv:
Flex-Algorithm : 128
Metric-Type : delay
Calculation-Type : 0
Priority : 50
Flags: M
Level (1) Capability Count : 2
Displaying Level 2 capabilities
LSP ID : Dut-A.00-00
Router Cap : 10.20.1.1, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:10001
SR Alg: metric based SPF, 128
Node MSD Cap: BMI : 12 ERLD : 15
LSP ID : Dut-B.00-00
Router Cap : 10.20.1.2, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:10001
SR Alg: metric based SPF, 128
Node MSD Cap: BMI : 12 ERLD : 15
FAD Sub-Tlv:
Flex-Algorithm : 128
Metric-Type : delay
Calculation-Type : 0
Priority : 100
Flags: M
LSP ID : Dut-C.00-00
Router Cap : 10.20.1.3, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:10001
SR Alg: metric based SPF, 128
Node MSD Cap: BMI : 12 ERLD : 15
Level (2) Capability Count : 3
===============================================================================
*A:Dut-B#
Label |
Description |
---|---|
Flex-Algorithm |
The flexible algorithm number |
Priority |
Displays the FAD priority; It is the tiebreaker when multiple FADs are received |
Metric Type |
The metric used by the winning FAD igp — the IGP metric is used te-metric — the TE metric is used delay — the delay metric is used |
Calculation Type |
Displays the calculation type; for SPF a zero value is only defined |
Flags |
Displays the FAD Flags; the M-flag is used for inter-area; when set, the metric must be used for inter-area traffic to avoid loops and blackhole traffic on ABR/ASBR |
capabilities
Syntax
capabilities [router-id]
Context
[Tree] (show>router>ospf capabilities)
[Tree] (show>router>ospf3 capabilities)
Full Context
show router ospf capabilities
show router ospf3 capabilities
Description
This command displays the entries in the Router Information (RI) LSAs.
Parameters
- router-id
-
Lists only the LSAs related to that router ID. If no router-id is specified, all database entries are listed.
Platforms
All
Output
OSPF Capabilities Output
The following table describes the standard and detailed command output fields for OSPF capabilities.
Sample Output*A:Dut-C# show router ospf capabilities
===============================================================================
Rtr Base OSPFv2 Instance 0 Capabilities
===============================================================================
scope Router Id Capabilities
-------------------------------------------------------------------------------
Area 10.20.1.2 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 22000 range 1001
Area 10.20.1.3 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 23030 range 71
Area 10.20.1.4 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 24000 range 1001
Area 10.20.1.5 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 25000 range 1001
Area 10.20.1.1 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 21000 range 1001
Area 10.20.1.2 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 22000 range 1001
Area 10.20.1.3 0x14: Stub P2P-VLAN
SR Algorithm: IGP-metric-based-SPF
SR Label Range: start label 23030 range 71
-------------------------------------------------------------------------------
No. of LSAs: 7
===============================================================================
capture-sap
capture-sap
Syntax
capture-sap [statistics] sap-id
Context
[Tree] (show>service>id>dynsvc capture-sap)
Full Context
show service id dynamic-services capture-sap
Description
This command displays the status and statistics of a dynamic services capture. Statistics include counters for the number of data triggers received and data trigger drop reasons.
This command is not available in the MD-CLI.
Parameters
- sap-id
-
Specifies the dynamic services capture SAP.
- statistics
-
Displays data trigger receive and drop reason counters for this dynamic services capture SAP.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of capture SAP information.
Sample Output# show service id 10 dynamic-services capture-sap 1/1/1:10.*
===============================================================================
Dynamic Services Capture SAP 1/1/1:10.*
===============================================================================
Dynamic services policy : dyn-svc-1
Administrative state : in-service
-------------------------------------------------------------------------------
Last Mgmt Change : 01/20/2016 12:54:06
===============================================================================
# show service id 10 dynamic-services capture-sap 1/1/1:10.* statistics
===============================================================================
Dynamic Services Capture SAP 1/1/1:10.* Statistics
===============================================================================
Data packets received by SAP : 0
-------------------------------------------------------------------------------
Drop Reason Counters
-------------------------------------------------------------------------------
No policy configured at capture SAP level : 0
No authentication configured in policy : 0
Data-trigger already exists : 0
Lockout is active : 0
Reached data-trigger system limit : 0
No memory available : 0
Unsuccessful authentication : 0
No data-trigger SAP-id in authentication : 0
Corresponding dynamic SAP is not created : 0
===============================================================================
Capture SAP Field Descriptions describes the Capture SAP policy fields.
Counter |
Description |
---|---|
Data packets received by SAP |
The number of dynamic service data triggers received on the capture SAP that reached the CPM. |
No policy configured at capture SAP level |
There is no dynamic-services-policy configured at the capture SAP. This is required to determine the authentication destination. |
No authentication configured in policy |
The authentication section in the specified in dynamic services policy is missing or incomplete. |
Data-trigger already exists |
A new data trigger frame is received for an existing data trigger that is authenticated, but the corresponding dynamic SAP is not yet created. The new data trigger packet is dropped. |
Lockout is active |
The data trigger for this managed SAP is currently in a lockout state due to previous authentication failures. |
Reached data-trigger system limit |
The maximum number of dynamic service data triggers supported on the system is reached. Additional data triggers are dropped. |
No memory available |
There is not enough system memory available to process the data trigger. |
Unsuccessful authentication |
The authentication for a data trigger on this capture SAP failed or timed out. |
No data-trigger SAP-id in authentication |
The dynamic services data trigger SAP ID is not provided in authentication. This is a mandatory parameter. |
Corresponding dynamic SAP is not created |
The data trigger successfully authenticated but the corresponding dynamic SAP was not created. This is typically caused by a dynamic services script error. |
capture-sap
Syntax
capture-sap [statistics] sap-id
Context
[Tree] (clear>service>id>dynsvc capture-sap)
Full Context
clear service id dynamic-services capture-sap
Description
This command clears the dynamic services capture SAP control plane statistics (data triggers received and data trigger drop reason counters).
Parameters
- statistics
-
Clears the data trigger statistics for a capture SAP.
- sap-id
-
Specifies the dynamic services capture SAP.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
card
card
Syntax
card slot-number cpu [sample-period seconds]
card slot-number fp fp-number dist-cpu-protection
card slot-number fp fp-number [tap tap-number] ingress per-egress-fp-stats
card slot-number fp fp-number [tap tap-number] egress per-ingress-fp-stats
card slot-number fp fp-number policy-accounting
card slot-number memory-pools
card state
card [slot-number]
card [slot-number] detail
card slot-number fp fp-number fwd-engine drop-reason statistics
card slot-number fp fp-number ingress queue-group mode {access | network}
card slot-number [detail] fp fp-number ingress queue-group queue-group-name instance [instance-number] mode {access | network} [ statistics]
Context
[Tree] (show card)
Full Context
show card
Description
This command shows card information.
If no command line parameters are specified, a card summary for all cards is displayed.
Parameters
- slot-number
-
Displays information for the specified card slot.
- cpu
-
Displays CPU utilization.
- seconds
-
Displays the number of seconds over which to sample CPU task utilization.
- fp-number
-
Displays information for the specified forwarding plane.
- dist-cpu-protection
-
Displays the distributed CPU protection information.
- policy-accounting
-
Displays the policy accounting information.
- memory-pools
-
Displays the memory pools for the card.
- state
-
Displays provisioned and equipped card and MDA information.
- detail
-
Displays detailed card information.
- fwd-engine
-
Displays forwarding engine information.
- drop-reason
-
Displays drop reason information.
- statistics
-
Displays statistics information.
- ingress
-
Specifies statistics are ingress related.
- egress
-
Specifies statistics are egress related.
- tap-number
-
Displays the source TAP number.
- per-egress-fp-stats
-
Displays packet and octet statistics for unicast traffic sent from the specified FP to each destination FP. Only supported on 7750 SR-1 and 7750 SR-s platforms.
- per-ingress-fp-stats
-
Displays packet and octet statistics for unicast traffic received by the specified FP from each source FP. Only supported on 7750 SR-1 and 7750 SR-s platforms.
- queue-group
-
Displays queue group information.
- mode
-
Specifies the mode in which the card will operate.
- access
-
Displays information for the queue groups related to access mode.
- network
-
Displays information for the queue groups related to network mode.
Platforms
All
Output
See the following sections for sample outputs:
-
Sample Output: show card state (showing 7750 SR-14s Chassis)
-
Sample Output: show card state (showing 7450 ESS-12 Chassis)
-
Sample Output: show card <slot-number> detail (showing IOM5-e Card)
-
Sample Output: show card <slot-number> detail (showing XCM-20 Card)
-
Output Fields: show card <slot-number> detail (for an IOM or XCM Card)
-
Sample Output: show card <slot-number> detail (showing CPM5 Cards)
-
Sample Output: show card <slot-number> detail (showing CPM-x20 Cards)
-
Sample Output: show card <slot-number> detail (showing IOM iwth license detail)
-
Output Fields: show card <slot-number> detail (showing IOM with license level)
-
Sample Output: show card <slot-number> fp fwd-engine drop-reason statistics
-
Output Fields: show card<slot-number> fp fwd-engine drop-reason statistics
-
Sample Output: show card <slot-number> fp <fp-number> ingress per-egress-fp-stats
-
Sample Output: show card <slot-number> fp <fp-number> ingress per-egress-fp-stats tap <tap-number>
-
Sample Output: show card <slot-number> fp <fp-number> egress per-ingress-fp-stats
-
Output Fields: show card <slot-number> fp <fp-number> ingress per-egress-fp-stats
*A:Dut-A# show card
===============================================================================
Card Summary
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
6 iom4-e up up
7 iom4-e up up
8 iom4-e-hs up up
9 iom4-e up up
A cpm5 up up/active
B cpm5 up up/standby
===============================================================================
Sample Output: show card (showing the 7950 XRS-40)
A:Dut-A# show card
===============================================================================
Card Summary
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
1 xcm-x20 up up
2 xcm-x20 up up
A cpm-x20 up up/active
B cpm-x20 up up/standby
C cpm-x20 up down/ext-stby
D cpm-x20 up up/ext-actv
===============================================================================
Output Fields: show card
Output Field: show card describes the output fields for the show card command.
Label |
Description |
---|---|
Slot |
The slot number of the card in the chassis. |
Provisioned Type |
The card type that is configured for the slot. Note: CPMs C and D do not appear in the summary unless the Chassis Topology is Extended (for the 7950 XRS-40). |
Equipped Type |
The card type that is actually populated in the slot. Note: CPMs C and D do not appear in the summary unless the Chassis Topology is Extended (for the7950 XRS-40). |
Admin State |
Up — The card is administratively up. Down — The card is administratively down. |
Operational State |
Up — The card is operationally up. Down — The card is operationally down. active — The CPM is the Active CPM for the system (actively managing the system components, processing various protocols, and so on). standby — The CPM is the Standby CPM. The standby is hot synchronized with the Active CPM. ext-actv — The CPM is operating in an Extension role in a 7950 XRS-40 system and is the active extension CPM for the chassis in which it sits. ext-stby — The CPM is operating in an Extension role in a 7950 XRS-40 system and is the standby extension CPM for the chassis in which it sits. |
Comments |
Active — Indicates if the CPM is the active state. Standby — Indicates if the CPM is the standby state. No SFM — Indicates no SFM is online that is usable by this card. Pwr Save — Indicates if the card is in power save mode. Lo Power — Indicates if the card is in low power mode. It is prevented from booting by power management. SFM Test — Indicates card is being held in booting because a B2B standalone SFM inter-connect test is in progress. No MDA — Indicates the card is waiting for MDAs. MDAs are either missing or failed. |
*A:Dut-A# show card state
===============================================================================
Card State
===============================================================================
Slot/ Provisioned Type Admin Operational Num Num Comments
Id Equipped Type (if different) State State Ports MDA
-------------------------------------------------------------------------------
6 iom4-e up up 2
6/1 me40-1gb-csfp up up 40
6/2 me40-1gb-csfp up up 40
7 iom4-e up up 2
7/1 me40-1gb-csfp up up 40
8 iom4-e-hs up up 2
8/1 me12-10/1gb-sfp+ up up 12
8/2 me40-1gb-csfp up up 40
9 iom4-e up up 2
9/1 me12-10/1gb-sfp+ up up 12
9/2 me12-10/1gb-sfp+ up up 12
A cpm5 up up Active
B cpm5 up up Standby
===============================================================================
Sample Output: show card state (showing 7750 SR-14s
Chassis)
A:Dut-O# show card state
===============================================================================
Card State
===============================================================================
Slot/ Provisioned Type Admin Operational Num Num Comments
Id Equipped Type (if different) State State Ports MDA
-------------------------------------------------------------------------------
1 xcm-14s up up 2
1/1 s18-100gb-qsfp28:he1200g+ up up 18
1/x2 iom-s-3.0t:he3000g+ up up
1/x2/1 ms18-100gb-qsfp28 up up 18
1/x2/2 ms4-400g-qsfpdd+4-100g-qsfp28 up up 8
2 xcm-14s up up 2
2/x1 iom-s-3.0t:he3000g+ up up
2/x1/1 ms6-200gb-cfp2-dco up up 6
6 xcm-14s up up 2
6/1 s36-400gb-qsfpdd:he4800g+ up up 36
6/2 s36-100gb-qsfp28:he2400g+ up up 36
A cpm-s up up Active
B cpm-s up up Standby
===============================================================================
Sample Output: show card state (showing 7450 ESS-12 Chassis)
A:Dut-B# show card state
===============================================================================
Card State
===============================================================================
Slot/ Provisioned Type Admin Operational Num Num Comments
Id Equipped Type (if different) State State Ports MDA
-------------------------------------------------------------------------------
6 imm-1pac-fp3 up up 1
6/1 p1-100g-cfp up up 1
7 imm-2pac-fp3 up up 2
7/2 p20-1gb-sfp up up 20
8 imm-2pac-fp3 up up 2
8/1 isa2-bb up up 7
p-isa2-ms
8/2 p3-40g-qsfp up up 3
A cpm5 up up Active
B cpm5 up up Standby
===============================================================================
Sample Output: show card state (showing a 7950 XRS
Chassis)
A:Dut-A# show card state
===============================================================================
Card State
===============================================================================
Slot/ Provisioned Type Admin Operational Num Num Comments
Id Equipped Type (if different) State State Ports MDA
-------------------------------------------------------------------------------
1 xcm-x20 up up 2
1/1 cx20-10g-sfp up up 20
1/2 cx20-10g-sfp up up 20
2 xcm-x20 up up 2
2/1 cx20-10g-sfp up up 20
A cpm-x20 up up Active
B cpm-x20 up up Standby
===============================================================================
Output Fields: show card state
Output Fields: show card state describes the output fields for the show card state command.
Label |
Description |
---|---|
Slot/MDA |
The slot number of the card in the chassis. |
Provisioned Type |
The card type that is configured for the slot. |
Equipped Type |
The card type that is actually populated in the slot. |
Admin State |
Up — The card is administratively up. Down — The card is administratively down. |
Operational State |
Up — The card is operationally up. Provisioned — There is no card in the slot but it has been pre-configured. |
Num Ports |
The number of ports available on the MDA. |
Num MDA |
The number of MDAs installed. |
Comments |
Active — Indicates if the CPM is the active state. Standby — Indicates if the CPM is the standby state. No SFM — Indicates no SFM is online that is usable by this card. Pwr Save — Indicates if the card is in power save mode. Lo Power — Indicates if the card is in low power mode. It is prevented from booting by power management. SFM Test — Indicates card is being held in booting because a B2B standalone SFM inter-connect test is in progress. No MDA — Indicates the card is waiting for MDAs. MDAs are either missing or failed. |
*A:Dut-A# show card 1 detail
===============================================================================
Card 1
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
1 iom5-e:he1200g+ up up
IOM Card Licensing Data
Licensed Level : he1200g+
Description : 1.2T /w Agg to 2.4T, High Edge Routing
IOM Card Specific Data
Clock source : none
Fail On Error : Disabled
Reset On Recoverable Error : Disabled
Available MDA slots : 2
Installed MDAs : 2
FP 1 Specific Data
WRED Admin State : Out Of Service
WRED buffer-allocation max : 2500
WRED buffer-allocation min : 2500
WRED reserved-cbs max : 2500
WRED reserved-cbs min : 2500
WRED Slope Policy : default
hi-bw-mc-srcEgress Alarm : disabled
hi-bw-mc-srcEgress Group : 0
mc-path-mgmt Admin State : Out Of Service
Ingress Bandwidth Policy : default
FP Resource Policy : default
Hw-Agg-Shaping QSets : True
Hw-Agg-Shaping QSet Size : 4
Hw-Agg-Shaping In Use : saps
Stable Pool Sizing : False
Ingress Buffer Pool Size : 8257536 KB
Egress Buffer Pool Size : 8257536 KB
Initial Extract Priority Mode : uniform
HS Pool Policy : None
HS Fixed High Threshold Delta : default
Generation : FP4
Network ingress queue policy : default
Hardware Data
Platform type : 7750
Part number : 3HE12332CARB01
CLEI code : INUIAD3HAA
Serial number : NS1936F7144
Manufacture date : 09082019
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0926-03
Administrative state : up
Operational state : up
Temperature : 60C
Temperature threshold : 75C
Software boot (rom) version : X-0.0.I6157 on Thu Jan 16 18:06:36 PST
2020 by builder
Software version : TiMOS-I-21.2.B1-6 iom/hops64 Nokia 7750 SR
Copyright (c) 2000-2021 Nokia.
All rights reserved. All use subject to
applicable license agreements.
Built on Fri Feb 5 18:15:30 PST 2021 by
builder in /builds/c/212B/B1-6/panos/main/
sros
Time of last boot : 2021/02/09 07:35:30
Current alarm state : alarm cleared
Base MAC address : 14:7b:ac:b4:b0:e1
Firmware revision status : acceptable
Last bootup reason : clear card
Memory capacity : 16,384 MB
===============================================================================
*A:Dut-A#
Sample Output: show card <slot-number> detail (showing XCM-20
Card)
A:bkvm20# show card 2 detail
===============================================================================
Card 2
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
2 xcm2-x20 up provisioned
(not equipped)
IOM Card Specific Data
Clock source : none
Fail On Error : Disabled
Available MDA slots : 2
Installed MDAs : 0
FP 1 Specific Data
WRED Admin State : Out Of Service
WRED buffer-allocation max : 2500
WRED buffer-allocation min : 2500
WRED reserved-cbs max : 2500
WRED reserved-cbs min : 2500
WRED Slope Policy : default
hi-bw-mc-srcEgress Alarm : disabled
hi-bw-mc-srcEgress Group : 0
mc-path-mgmt Admin State : Out Of Service
Ingress Bandwidth Policy : default
FP Resource Policy : default
Stable Pool Sizing : False
Initial Extract Priority Mode : uniform
Generation : FP4
Network ingress queue policy : default
FP 2 Specific Data
WRED Admin State : Out Of Service
WRED buffer-allocation max : 2500
WRED buffer-allocation min : 2500
WRED reserved-cbs max : 2500
WRED reserved-cbs min : 2500
WRED Slope Policy : default
hi-bw-mc-srcEgress Alarm : disabled
hi-bw-mc-srcEgress Group : 0
mc-path-mgmt Admin State : Out Of Service
Ingress Bandwidth Policy : default
FP Resource Policy : default
Stable Pool Sizing : False
Initial Extract Priority Mode : uniform
Generation : FP4
Network ingress queue policy : default
FP 3 Specific Data
WRED Admin State : Out Of Service
WRED buffer-allocation max : 2500
WRED buffer-allocation min : 2500
WRED reserved-cbs max : 2500
WRED reserved-cbs min : 2500
WRED Slope Policy : default
hi-bw-mc-srcEgress Alarm : disabled
hi-bw-mc-srcEgress Group : 0
mc-path-mgmt Admin State : Out Of Service
Ingress Bandwidth Policy : default
FP Resource Policy : default
Stable Pool Sizing : False
Initial Extract Priority Mode : uniform
Generation : FP4
Network ingress queue policy : default
Hardware Data
Platform type : N/A
Part number :
CLEI code :
Serial number :
Manufacture date :
Manufacturing deviations : (Not Specified)
Manufacturing assembly number :
Administrative state : up
Operational state : provisioned
Software boot (rom) version : (Not Specified)
Software version : (Not Specified)
Time of last boot : N/A
Current alarm state : alarm cleared
Base MAC address :
Last bootup reason :
Memory capacity : 0 MB
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 0.00 Volts (N/A)
Current : 0.00 Volts
Peak : 0.00 Volts (N/A)
Wattage
Minimum : 0.00 Watts (N/A)
Current : 0.00 Watts
Peak : 0.00 Watts (N/A)
Max Required : 282.00 Watts
Amperage
Minimum : 0.00 Amps (N/A)
Current : 0.00 Amps
Peak : 0.00 Amps (N/A)
===============================================================================
A:bkvm20#
Output Fields: show card <slot-number> detail (for an IOM or
XCM Card)
Output Fields: show card <slot-number> detail (for an IOM or XCM Card) describes the output fields for the show card detail command.
Label |
Description |
---|---|
Clock source |
Source of clock for the IOM. Currently this parameter always displays "none”. |
Available MDA slots |
The number of MDA slots available on the IOM. |
Installed MDAs |
The number of MDAs installed on the IOM. |
FP Resource Policy |
The FP resource policy for the specified FP. |
Initial Extract Priority Mode |
The scheme used to select the initial drop priority of extracted control plane traffic. uniform — Initializes the drop priority of all extracted control traffic as high priority. l3-classify — Initializes the drop priority of all Layer 3 extracted control traffic (for example, BGP or OSPF) based on the QoS classification of the packets. See "Classification-Based Priority for Extracted Protocol Traffic" in the7450 ESS, 7750 SR, 7950 XRS, and VSR System Management Guide for more details. |
Part number |
The IOM part number. |
CLEI code |
The Common Language Location Identifier (CLLI) code string for the router. |
Serial number |
The serial number. Not user-modifiable. |
Manufacture date |
The chassis manufacture date. Not user-modifiable. |
Manufacturing string |
Factory-inputted manufacturing text string. Not user-modifiable. |
Manufacturing deviations |
Displays a record of changes by manufacturing to the hardware or software that is outside the normal revision control process. |
Administrative state |
Up — The card is administratively up. Down — The card is administratively down. |
Operational state |
Up — The card is operationally up. Down — The card is operationally down. |
Temperature |
Internal chassis temperature. |
Temperature threshold |
The value above which the internal temperature must rise in order to indicate that the temperature is critical. |
Software boot version |
The version of the boot image. |
Software version |
The software version number. |
Time of last boot |
The date and time the most recent boot occurred. |
Current alarm state |
Displays the alarm conditions for the specific board. |
Base MAC address |
Displays the base MAC address of the hardware component. |
Memory capacity |
Displays the memory capacity of the card. |
Generation |
Displays the FP generation of the assembly. N/A is displayed if there is no XMA installed in the card slot. |
Comments |
Active — Indicates if the CPM is the active state. Standby — Indicates if the CPM is the standby state. No SFM — Indicates no SFM is online that is usable by this card. Pwr Save — Indicates if the card is in power save mode. Lo Power — Indicates if the card is in low power mode. It is prevented from booting by power management. SFM Test — Indicates card is being held in booting because a B2B standalone SFM inter-connect test is in progress. No MDA — Indicates the card is waiting for MDAs. MDAs are either missing or failed. |
Network ingress queue policy |
Displays the name of the network ingress queue policy applied to the FP. |
B:Dut-D# show card A detail
===============================================================================
Card A
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
A cpm5 up up/active
BOF last modified : N/A
Config file version : FRI APR 12 01:08:10 2019 UTC
Config file last modified : N/A
Config file last saved : 2019/04/16 21:08:31
M/S clocking ref state : primary
Flash - cf1:
Administrative State : up
Operational state : up
Serial number : 20101124004146824682
Firmware revision : 20091110
Model number : SMART CF
Size : 3,907 MB
Free space : 798,240 KB
Percent Used : 80 %
Flash - cf2:
Administrative State : up
Operational state : up
Serial number : 20101124004180EB80EB
Firmware revision : 20091110
Model number : SMART CF
Size : 3,907 MB
Free space : 1,562 MB
Percent Used : 59 %
Flash - cf3:
Administrative State : up
Operational state : up
Serial number : 000060089160A700003F
Firmware revision : 110301a
Model number : SFCF32GBH1BO4TO-I-NC-543-ALU
Size : 31,248 MB
Free space : 27,771 MB
Percent Used : 11 %
Hardware Data
Platform type : 7750
Part number : 3HE08423AARC01
CLEI code : IPUCBGZ1AA
Serial number : NS155160462
Manufacture date : 12222015
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0553-05
Administrative state : up
Operational state : up
Temperature : 51C
Temperature threshold : 75C
Software boot (rom) version : X-13.0.R4 on Wed Jul 29 15:56:20 PDT 2015
by builder
Software version : TiMOS-C-16.0.R6 cpm/hops64 Nokia 7750 SR
Copyright (c) 2000-2019 Nokia.
All rights reserved. All use subject to
applicable license agreements.
Built on Wed Feb 27 14:42:05 PST 2019 by
builder in /builds/c/160B/R6/panos/main
Time of last boot : 2019/04/15 09:31:29
Current alarm state : alarm cleared
Base MAC address : e4:81:84:81:ca:06
Firmware revision status : acceptable
Memory capacity : 16,384 MB
System timing oscillator type : OCXO
==============================================================================
A:MLS2-SR164# show card "b" detail
===============================================================================
Card B
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
B cpm5 up up/standby
BOF last modified : N/A
Config file version :
Config file last modified : N/A
Config file last saved : N/A
M/S clocking ref state : secondary
Flash - cf1:
Administrative State : up
Operational state : not equipped
Flash - cf2:
Administrative State : up
Operational state : not equipped
Flash - cf3:
Administrative State : up
Operational state : up
Serial number : 000060078551A1000397
Firmware revision : 110301a
Model number : SFCF4096H1BO2TO-I-D1-543-ALU
Size : 3,904 MB
Free space : 1,135 MB
Percent Used : 70 %
Hardware Data
Platform type : 7750
Part number : 3HE08423AARC01
CLEI code : IPUCBGZ1AA
Serial number : NS160164783
Manufacture date : 01172016
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0553-05
Administrative state : up
Operational state : up
Temperature : 50C
Temperature threshold : 75C
Software boot (rom) version : X-13.0.R4 on Wed Jul 29 15:56:20 PDT 2015
by builder
Software version : TiMOS-C-16.0.R6 cpm/hops64 Nokia 7750 SR
Copyright (c) 2000-2019 Nokia.
All rights reserved. All use subject to
applicable license agreements.
Built on Wed Feb 27 14:42:05 PST 2019 by
builder in /builds/c/160B/R6/panos/main
Time of last boot : 2019/04/15 09:32:04
Current alarm state : alarm cleared
Base MAC address : e4:81:84:81:db:7c
Firmware revision status : acceptable
Memory capacity : 16,384 MB
System timing oscillator type : OCXO
===============================================================================
Sample Output: show card <slot-number> detail (showing
CPM-x20 Cards)
*A:bksim3107# show card A detail
===============================================================================
Card A
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
A cpm-x20 up up/active
BOF last modified : 2013/05/15 12:33:22
Config file version : FRI MAR 08 13:24:58 2013 UTC
Config file last modified : 2013/05/15 12:34:22
Config file last saved : 2013/05/15 12:36:22
M/S clocking ref state : primary
Flash - cf1:
Administrative State : up
Operational state : up
Serial number : serial-1
Firmware revision : v1.0
Model number : PC HD 1
Size : 1,950 MB
Free space : 1,950 MB
Flash - cf2:
Administrative State : up
Operational state : up
Serial number : serial-2
Firmware revision : v1.0
Model number : PC HD 2
Size : 0 Bytes
Free space : 0 Bytes
Flash - cf3:
Administrative State : up
Operational state : up
Serial number : serial-3
Firmware revision : v1.0
Model number : PC HD 3
Size : 18,432 Bytes
Free space : 6,144 Bytes
Hardware Data
Platform type : 7950
Part number : Sim Part#
CLEI code : Sim CLEI
Serial number : card-11
Manufacture date : 01012003
Manufacturing deviations : Sim MfgDeviation card-11
Manufacturing assembly number : 01-2345-67
Administrative state : up
Operational state : up
Temperature : -1C
Temperature threshold : 75C
Software boot (rom) version : simulated
Software version : TiMOS-C-11.0.R2 cpm/i386 Nokia 7950 XRS*
Time of last boot : 2013/05/13 08:10:33
Current alarm state : alarm cleared
Base MAC address : ac:9f:0b:00:00:01
Memory capacity : 3,072 MB
Inter Chassis CPM Interconnect
CPM Interconnect Port 1
Oper State : up
SFF Status : operational
CPM Interconnect Port 2
...
* indicates that the corresponding row element may have been truncated.
===============================================================================
*A:Dut-A# show card D detail
===============================================================================
Card D
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
D cpm-x20 up up/ext-stby
BOF last modified : N/A
Config file version :
Config file last modified : N/A
Config file last saved : N/A
M/S clocking ref state : secondary
Flash - cf1:
Administrative State : up
Operational state : up
Serial number : WE11K6300191
Firmware revision : 2.1ME
Model number : WDC SSD-D0128S-7117
Size : 122,089 MB
Free space : 122,089 MB
Flash - cf2:
Administrative State : up
Operational state : not equipped
Flash - cf3:
Administrative State : up
Operational state : up
Serial number : SPG2012061404165
Firmware revision : 20101222
Model number : SMART CF
Size : 3,907 MB
Free space : 3,802 MB
Hardware Data
Platform type : 7950
Part number : 3HE07116AARB01
CLEI code : IPUCA9T1AA
Serial number : NS13426D067
Manufacture date : 03162014
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0488-05
Administrative state : up
Operational state : up
Temperature : 39C
Temperature threshold : 75C
Software boot (rom) version : X-12.0.B1-120 on Wed Jul 16 18:55:26 PDT
2014 by builder
Software version : TiMOS-C-12.0.B1-120 cpm/hops64 Nokia_7950 XRS
7950 Copyright (c) 2000-2016 Nokia
All rights reserved. All use subject to
applicable license agreements.
Built on Wed Jul 16 19:26:12 PDT 2014 by
builder in /rel12.0/b1/B1-120/panos/main
Time of last boot : 2014/07/17 13:41:28
Current alarm state : alarm cleared
Base MAC address : 00:d0:f6:f3:3c:9e
Memory capacity : 8,192 MB
Hardware Resources (Power-Zone 2)
Voltage
Minimum : 53.10 Volts (07/17/2014 12:40:28)
Current : 53.16 Volts
Peak : 54.15 Volts (07/17/2014 12:18:27)
Wattage
Minimum : 151.10 Watts (07/17/2014 13:31:23)
Current : 202.61 Watts
Peak : 208.79 Watts (07/17/2014 13:00:07)
Max Required : 204.00 Watts
Amperage
Minimum : 3.69 Amps (07/17/2014 12:18:27)
Current : 3.82 Amps
Peak : 3.94 Amps (07/17/2014 13:07:25)
Inter Chassis CPM Interconnect
CPM Interconnect Port 1
Oper State : up
SFF Status : operational
CPM Interconnect Port 2
Oper State : up
SFF Status : operational
===============================================================================
Output Fields: show card <slot-number> detail (for a
CPM)
Output Fields: show card <slot-number> detail (for a CPM) describes the output fields for the show card detail command for a CPM card.
Label |
Description |
---|---|
Slot |
The slot of the card in the chassis. |
Card Provisioned |
The CPM type that is configured for the slot. Note: CPMs C and D will not show up in the summary unless the Chassis Topology is Extended (XRS-40). |
Card Equipped |
The CPM type that is actually populated in the slot. Note: CPMs C and D will not show up in the summary unless the Chassis Topology is Extended (XRS-40). |
Admin State |
Up — The CPM is administratively up. Down — The CPM is administratively down. |
Operational State |
Up — The CPM is operationally up. Down — The CPM is operationally down. |
Inter chassis cpm interconnect |
Up — The CPM is operationally up. Down — The CPM is operationally down. |
BOF last modified |
The date and time of the most recent BOF modification. |
Config file version |
The configuration file version. |
Config file last modified |
The date and time of the most recent config file modification. |
Config file last modified |
The date and time of the most recent config file modification. |
Config file last saved |
The date and time of the most recent config file save. |
CPM card status |
active — The card is acting as the primary (active) CPM in a redundant system. standby — The card is acting as the standby (secondary) CPM in a redundant system. |
Administrative state |
Up — The CPM is administratively up. Down — The CPM is administratively down. |
Operational state |
Up — The CPM is operationally up. Down — The CPM is operationally down. |
Serial number |
The compact flash part number. Not user modifiable. |
Firmware revision |
The firmware version. Not user modifiable. |
Model number |
The compact flash model number. Not user modifiable. |
Size |
The amount of space available on the compact flash card. |
Free space |
The amount of space remaining on the compact flash card. |
Part number |
The CPM part number. |
CLEI code |
The code used to identify the router. |
Serial number |
The CPM part number. Not user modifiable. |
Manufacture date |
The chassis manufacture date. Not user modifiable. |
Manufacturing string |
Factory-set manufacturing text string. Not user modifiable. |
Administrative state |
Up — The card is administratively up. Down — The card is administratively down. |
Operational state |
Up — The card is operationally up. Down — The card is operationally down. |
Time of last boot |
The date and time the most recent boot occurred. |
Current alarm state |
Displays the alarm conditions for the specific board. |
Status |
Displays the current status. |
Temperature |
Internal chassis temperature. |
Temperature threshold |
The value above which the internal temperature must rise in order to indicate that the temperature is critical. |
Software boot version |
The version of the boot image. |
Memory capacity |
The total amount of memory. |
Comments |
Active — Indicates if the CPM is the active state. Standby — Indicates if the CPM is the standby state. No SFM — Indicates no SFM is online that is usable by this card. Pwr Save — Indicates if the card is in power save mode. Lo Power — Indicates if the card is in low power mode. It is prevented from booting by power management. SFM Test — Indicates card is being held in booting because a B2B standalone SFM inter-connect test is in progress. No MDA — Indicates the card is waiting for MDAs. MDAs are either missing or failed. |
*A:bkvm18# show card 1 detail
===============================================================================
Card 1
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
1 iom5-e:he1200g+ up up
IOM Card Licensing Data
Licensed Level : he1200g+
Description : 1.2T /w Agg to 2.4T, High Edge Routing
Licensed Bandwidth Used : 900 Gbps
IOM Card Specific Data
Clock source : none
Fail On Error : Disabled
Reset On Recoverable Error : Disabled
Available MDA slots : 2
Installed MDAs : 0
FP 1 Specific Data
WRED Admin State : Out Of Service
WRED buffer-allocation max : 2500
WRED buffer-allocation min : 2500
WRED reserved-cbs max : 2500
WRED reserved-cbs min : 2500
WRED Slope Policy : default
hi-bw-mc-srcEgress Alarm : disabled
hi-bw-mc-srcEgress Group : 0
mc-path-mgmt Admin State : Out Of Service
Ingress Bandwidth Policy : default
FP Resource Policy : default
Stable Pool Sizing : False
Ingress Buffer Allocation : 50.00
Initial Extract Priority Mode : uniform
HS Pool Policy : None
HS Fixed High Threshold Delta : default
Generation : FP4
Network ingress queue policy : default
Hardware Data
Platform type : N/A
Part number :
CLEI code :
Serial number :
Manufacture date :
Manufacturing deviations : (Not Specified)
Manufacturing assembly number :
Administrative state : up
Operational state : provisioned
Software boot (rom) version : (Not Specified)
Software version : (Not Specified)
Time of last boot : N/A
Current alarm state : alarm cleared
Base MAC address :
Last bootup reason :
Memory capacity : 0 MB
Output Fields: show card <slot-number> detail (showing IOM
with license level)
Output Fields: show card <slot-number> detail (showing IOM with license level) describes the output fields for the show card detail command with IOM licensing information.
Label |
Description |
---|---|
Slot |
The slot of the card in the chassis. |
Provisioned Type |
The IOM type and level that is configured for the slot. |
Equipped Type (if different) |
The IOM type and level that is actually populated in the slot if it is different than the Provisioned Type. |
Admin State |
Up — The IOM is administratively up. Down — The IOM is administratively down. |
Operational State |
Up — The IOM is operationally up. Down — The IOM is operationally down. |
Licensed Level |
License level of the card. |
Description |
Description of the license. |
Licensed Bandwidth Used |
The total connector bandwidth configured on the assembly. |
Comments |
Active — Indicates if the CPM is the active state. Standby — Indicates if the CPM is the standby state. No SFM — Indicates no SFM is online that is usable by this card. Pwr Save — Indicates if the card is in power save mode. Lo Power — Indicates if the card is in low power mode. It is prevented from booting by power management. SFM Test — Indicates card is being held in booting because a B2B standalone SFM inter-connect test is in progress. No MDA — Indicates the card is waiting for MDAs. MDAs are either missing or failed. |
*A:cses-V93# show card 1 fp 1 fwd-engine drop-reason statistics
===============================================================================
Card 1 FP 1 Egress Forwarding Engine Drop Reason Statistics
===============================================================================
Egress Encapsulation Exceeded 0
MTU Exceeded 0
Frame too big for port 4
===============================================================================
Output Fields: show card<slot-number> fp fwd-engine
drop-reason statistics
Output Fields: show card slot-number fp fwd-engine drop-reason describes the output fields for the show card fp fwd-engine drop-reason command.
Label |
Description |
---|---|
Card |
The card in the chassis. |
FP |
The egress forwarding plane hardware component. |
Egress Encapsulation Exceeded |
Addition of egress encapsulation headers would have exceeded the maximum frame size. |
MTU Exceeded |
Protocol supports packet fragmentation but fragmentation was blocked (for example, packet is IPv6 or packet is IPv4 and DF set to one). |
Frame too big for port |
Final check before transmitting has detected frame exceeded the port MTU. |
A single frame can only result in one drop reason statistic being incremented.
# show card 4 fp 5 ingress per-egress-fp-stats
===============================================================================
Card 4 FP 5 TAP 1 (Ingress Per-Egress FP Statistics)
===============================================================================
To FP/TAP Priority Forwarded Packets Forwarded Octets
-------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 114919092 114919092000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 5782 2154196
Best-Effort 0 0
===============================================================================
===============================================================================
Card 4 FP 5 TAP 2 (Ingress Per-Egress FP Statistics)
===============================================================================
To FP/TAP Priority Forwarded Packets Forwarded Octets
-------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 114919195 114919195000
===============================================================================
Sample Output: show card <slot-number> fp <fp-number>
ingress per-egress-fp-stats tap <tap-number>
*A:Dut-A# show card 4 fp 5 ingress per-egress-fp-stats tap 1
===============================================================================
Card 4 FP 5 TAP 1 (Ingress Per-Egress FP Statistics)
===============================================================================
To FP/TAP Priority Forwarded Packets Forwarded Octets
-------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 115935212 115935212000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 5816 2169292
Best-Effort 0 0
===============================================================================
-------------------------------------------------------------------------------
===============================================================================
*A:Dut-A# show card 4 fp 5 ingress per-egress-fp-stats tap 2
===============================================================================
Card 4 FP 5 TAP 2 (Ingress Per-Egress FP Statistics)
===============================================================================*
To FP/TAP Priority Forwarded Packets Forwarded Octets
-------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 115935316 115935316000
===============================================================================
Sample Output: show card <slot-number> fp <fp-number>
egress per-ingress-fp-stats
# show card 1 fp 1 egress per-ingress-fp-stats
===============================================================================
Card 1 FP 1 TAP 1 Egress Per-Ingress FP Statistics
===============================================================================
To FP/TAP Priority Received Packets Received Octets
-------------------------------------------------------------------------------
1 1/1 Expedite 172437 2207203840
Best-Effort 12345678 3160493568
1 2/1 Expedite 103446 1324118016
Best-Effort 987654 252839424
1 3/1 Expedite 6899108 883085824
Best-Effort 11223344 2873176064
1 4/1 Expedite 0 0
Best-Effort 0 0
2 1/1 Expedite 0 0
Best-Effort 0 0
2 2/2 Expedite 0 0
Best-Effort 0 0
-------------------------------------------------------------------------------
===============================================================================
Output Fields: show card <slot-number> fp <fp-number>
ingress per-egress-fp-stats
Output Fields: egress and ingress card statistics per ingress or egress FP describes the output fields for the egress and ingress card statistics per ingress or egress FP.
Label |
Description |
---|---|
To FP/TAP |
Displays the To forwarding plane TAP information. |
Priority |
Displays the priority (Best-Effort, Expedite, or Auto-Expedite). |
Forwarded Packets |
Displays the unicast packet statistics sent from the specified FP to the destination FP. |
Forwarded Octets |
Displays the unicast octet statistics sent from the specified FP to the destination FP. |
card
Syntax
card slot-number
card slot-number fp fp-number hs-pool high-water-mark
card slot-number fp fp-number hs-pool high-water-mark mid-pool [value]
card slot-number fp fp-number hs-pool high-water-mark root-pool [value]
card slot-number fp fp-number hs-pool high-water-mark system
card slot-number fp fp-number dist-cpu-protection
card slot-number fp fp-number ingress per-egress-fp-stats
card slot-number fp fp-number egress per-ingress-fp-stats
card slot-number soft [hard-reset-unsupported-mdas]
card slot-number fp fp-number fwd-engine drop-reason statistics
card slot-number fp fp-number ingress mode {access | network} queue-group group-name instance instance statistics
Context
[Tree] (clear card)
Full Context
clear card
Description
This command re-initializes the card in the specified slot. A clear card command (without the soft) is referred to as a Hard Reset. A clear card x soft command (with the soft) is referred to as a Soft Reset.
Parameters
- slot-number
-
Clears information for the specified card slot.
- fp-number
-
Displays information for the specified forwarding plane.
- high-water-mark
-
Clears the high water marks within the HS pool on the specified card and FP.
- mid-pool
-
Clears the high water marks within the mid pools in the HS pool and on the specified card and FP.
- root-pool
-
Clears the high water marks within the root pools in the HS pool and on the specified card and FP.
- system
-
Clears the high water marks within the in the HS system pool and on the specified card and FP.
- dist-cpu-protection
-
Clears the distributed CPU protection information.
- soft
-
Issues a soft reset of the I/O module (IOM).
- hard-reset-unsupported-mdas
-
Allows a soft reset operation when some of the MDA’s cannot perform a soft reset. A soft reset is performed on MDAs that support a soft reset and a hard reset is performed on MDAs that do not support soft resets.
- fwd-engine
-
Specifies to clear the forwarding engine information.
- drop-reason
-
Specifies to clear the drop reason information.
- statistics
-
Specifies to clear the statistics.
- ingress
-
Specifies to clear the ingress information.
- egress
-
Specifies to clear the egress information.
- per-egress-fp-stats
-
Specifies to clear packet and octet statistics for unicast traffic sent from the specified FP to each destination FP. Only supported on 7750 SR-1 and 7750 SR-s platforms.
- per-ingress-fp-stats
-
Specifies to clear packet and octet statistics for unicast traffic received by the specified FP from each source FP. Only supported on 7750 SR-1 and 7750 SR-s platforms.
- mode
-
Specifies the mode in which the card is to operate.
- access
-
Specifies to clear the access mode information.
- network
-
Specifies to clear the network mode information.
- group-name
-
Specifies the group name, to a maximum of 32 characters.
- instance
-
Specifies the instance of the named queue group to be cleared.
Platforms
All
card
Syntax
card slot-number fp fp-number queue-group queue-group-name instance instance-id [{access | network}] [{ingress | egress}] [arbiter {name | root}] [port port-id] [{detail | root-detail | thresholds | priority-info | depth}]
Context
[Tree] (show>qos>policer-hierarchy card)
Full Context
show qos policer-hierarchy card
Description
This command displays physical card related information.
Parameters
- slot-number
-
Displays information about the slot number of the card in the chassis. The maximum slot number is platform dependent.
- fp-number
-
Displays information about the specified forwarding plane number.
- queue-group-name
-
Displays information about the specified queue group name, up to 32 characters.
- instance-id
-
Displays information about the instance of the named queue group.
- name
-
Displays information about the name of the QoS arbiter.
- root
-
Displays information about the arbiter root.
- port-id
-
Displays information about the specified port ID.
- access
-
Displays policer-hierarchy statistics applied on an access port.
- network
-
Displays policer-hierarchy statistics applied on a network port.
- ingress
-
Displays ingress queue group information.
- egress
-
Displays egress queue group information.
- detail
-
Displays detailed information.
- root-detail
-
Displays detailed information about the arbiter root.
- thresholds
-
Displays the threshold, parenting, rate, and traffic information related to a policer.
- priority-info
-
Displays the threshold information related to the root arbiter.
- depth
-
Displays the bucket depth, parenting, rate, and traffic information related to a policer.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
card
Syntax
card [slot-num]
card [slot-num] all
Context
[Tree] (tools>dump>resource-usage card)
Full Context
tools dump resource-usage card
Description
This command displays resource information for cards.
Parameters
- slot-num
-
Specifies a card slot.
- all
-
Displays all available information for the card, including resource usage information for all child objects of the card such as FPs and MDAs.
Platforms
All
card
Syntax
card slot-number fp fp-number ingress {access | network} queue-group queue-group-name instance instance-id [absolute | percent-rate] [interval seconds] [repeat repeat] policer policer-id [reference-rate]
card slot-number fp fp-number ingress [tap tap-number] per-egress-fp-stats [interval seconds] [repeat repeat] [absolute | rate]
card slot-number fp fp-number [tap tap-number] egress per-ingress-fp-stats [interval seconds] [ repeat repeat] [absolute | rate]
Context
[Tree] (monitor card)
Full Context
monitor card
Description
This command monitors statistics in an ingress and egress Forwarding Plane (FP).
Parameters
- slot-number
-
Monitors information on the specified card slot.
- fp-number
-
Monitors information on the specified FP.
- ingress
-
Monitors information on the ingress.
- egress
-
Monitors information on the egress.
- access
-
Displays policer statistics on the FP access.
- network
-
Displays policer statistics on the FP network.
- queue-group-name
-
Specifies the queue group name, up to 32 characters.
- instance-id
-
Specifies the identification of a specific instance of the queue group.
- absolute
-
Displays the raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- percent-rate
-
Displays the rate-per-second for each statistic based on the reference rate of 10G.
- seconds
-
Specifies the interval for each display in seconds.
- repeat
-
Specifies how many times the command is repeated.
- policer-id
-
Must exist within the queue-group template applied to the ingress context of the forwarding plane.
- reference-rate
-
Displays the rate-per-second for each statistic as a percentage based on the reference rate specified.
- tap-number
-
Specifies the source TAP.
- per-egress-fp-stats
-
Displays packet and octet statistics for unicast traffic sent from the specified FP to each destination FP.
- per-ingress-fp-stats
-
Displays packet and octet statistics for unicast traffic received by the specified FP from each source FP.
- rate
-
Displays the rate-per-second for each statistic instead of the delta.
Platforms
All
Output
See the following sections for sample outputs:
Sample Output Ingress per-egress-fp-stats# monitor card "4" fp 5 ingress per-egress-fp-stats
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 42659137 42659137000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3338 1054788
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 42659012 42659012000
==============================================================================
At time t = 11 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375377 1375377000
4 - 5/1 Expedite 0 0
Best-Effort 0 0
A - 1/1 Expedite 46 20832
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375605 1375605000
Sample Output Ingress per-egress-fp-stats rate
# monitor card "4" fp 5 ingress per-egress-fp-stats rate
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 45802801 45802801000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3444 1102780
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 45802905 45802905000
==============================================================================
At time t = 11 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125039 125039364 1000
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1921 0
Best-Effort 0 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125039 125039273 1000
==============================================================================
At time t = 22 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124999 124999273 999
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1867 0
Best-Effort 0 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124999 124999182 999
Sample Output Ingress per-egress-fp-stats absolute
# monitor card "4" fp 5 ingress per-egress-fp-stats absolute
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 49729775 49729775000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3585 1163992
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 49729878 49729878000
==============================================================================
At time t = 11 sec (Mode: Absolute)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 51104481 51104481000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3631 1184824
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 51104584 51104584000
==============================================================================
At time t = 22 sec (Mode: Absolute)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 52479477 52479477000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3677 1206224
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 52479581 52479581000
Sample Output Ingress per-egress-fp-stats absolute tap
# monitor card "4" fp 5 ingress per-egress-fp-stats absolute tap 1
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 53893930 53893930000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3726 1227188
Best-Effort 0 0
==============================================================================
At time t = 11 sec (Mode: Absolute)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 55269466 55269466000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3773 1248320
Best-Effort 0 0
# monitor card "4" fp 5 ingress per-egress-fp-stats absolute tap 2
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 56153283 56153283000
==============================================================================
At time t = 11 sec (Mode: Absolute)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 57528327 57528327000
Sample Output Ingress per-egress-fp-stats rate tap
# monitor card "4" fp 5 ingress per-egress-fp-stats rate tap 1
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 59487961 59487961000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 3915 1312280
Best-Effort 0 0
==============================================================================
At time t = 11 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125035 125034818 1000
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1955 0
Best-Effort 0 0 0
==============================================================================
At time t = 22 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124995 124994909 999
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1921 0
Best-Effort 0 0 0
==============================================================================
At time t = 33 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124994 124993818 999
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1867 0
Best-Effort 0 0 0
==============================================================================
At time t = 44 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125002 125001545 1000
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1886 0
Best-Effort 0 0 0
==============================================================================
At time t = 55 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124998 124998182 999
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1894 0
Best-Effort 0 0 0
==============================================================================
At time t = 66 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125001 125000636 1000
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1955 0
Best-Effort 0 0 0
==============================================================================
At time t = 77 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124998 124998273 999
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1921 0
Best-Effort 0 0 0
==============================================================================
At time t = 88 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125076 125075545 1000
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1867 0
Best-Effort 0 0 0
==============================================================================
At time t = 99 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 125039 125039091 1000
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1886 0
Best-Effort 0 0 0
==============================================================================
At time t = 110 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124999 124998636 999
4 - 5/1 Expedite 0 0 0
Best-Effort 0 0 0
A - 1/1 Expedite 4 1894 0
Best-Effort 0 0 0
==============================================================================
# monitor card "4" fp 5 ingress per-egress-fp-stats rate tap 2
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 84288530 84288530000
==============================================================================
At time t = 11 sec (Mode: Rate)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets Mbps
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0 0
Best-Effort 124982 124981818 999
Sample Output Ingress per-egress-fp-stats
# monitor card "4" fp 5 ingress per-egress-fp-stats
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 90150683 90150683000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 4949 1778224
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 90150787 90150787000
==============================================================================
At time t = 11 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375025 1375025000
4 - 5/1 Expedite 0 0
Best-Effort 0 0
A - 1/1 Expedite 47 21132
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375024 1375024000
==============================================================================
At time t = 22 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375003 1375003000
4 - 5/1 Expedite 0 0
Best-Effort 0 0
A - 1/1 Expedite 45 20532
Best-Effort 0 0
------------------------------------------------------------------------------
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375003 1375003000
Sample Output Ingress per-ingress-fp-stats tap
# monitor card "4" fp 5 ingress per-egress-fp-stats tap 1
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 93787778 93787778000
4 - 5/1 Expedite 792 788688
Best-Effort 0 0
A - 1/1 Expedite 5071 1833136
Best-Effort 0 0
==============================================================================
At time t = 11 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 1 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375605 1375605000
4 - 5/1 Expedite 0 0
Best-Effort 0 0
A - 1/1 Expedite 47 20748
Best-Effort 0 0
# monitor card "4" fp 5 ingress per-egress-fp-stats tap 2
==============================================================================
==============================================================================
At time t = 0 sec (Base Statistics)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 96041192 96041192000
==============================================================================
At time t = 11 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1374706 1374706000
==============================================================================
At time t = 22 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1374960 1374960000
==============================================================================
At time t = 33 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1374980 1374980000
==============================================================================
At time t = 44 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375009 1375009000
==============================================================================
At time t = 55 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375010 1375010000
==============================================================================
At time t = 66 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1374987 1374987000
==============================================================================
At time t = 77 sec (Mode: Delta)
==============================================================================
Card: 4 FP: 5 Tap: 2 (Ingress Per-Egress FP Statistics)
------------------------------------------------------------------------------
To FP/TAP Priority Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
1 - 2/1 Expedite 0 0
Best-Effort 1375005 1375005000
Sample Output Egress per-ingress-fp-stats interval repeat
*A:PE1# monitor card 1 fp 1 egress per-ingress-fp-stats interval 11 repeat 1
===============================================================================
Card 1 FP 1 TAP 1 Egress Per-Ingress FP Statistics
===============================================================================
To FP/TAP Priority Received Packets Received Octets
-------------------------------------------------------------------------------
1 1/1 Expedite 172437 2207203840
Best-Effort 12345678 3160493568
1 2/1 Expedite 103446 1324118016
Best-Effort 987654 252839424
1 3/1 Expedite 6899108 883085824
Best-Effort 11223344 2873176064
1 4/1 Expedite 0 0
Best-Effort 0 0
2 1/1 Expedite 0 0
Best-Effort 0 0
2 2/1 Expedite 0 0
Best-Effort 0 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 11 sec (Mode: Delta)
-------------------------------------------------------------------------------
1 1/1 Expedite 272437 2232803840
Best-Effort 12545678 3211693568
1 2/1 Expedite 403446 1400918016
Best-Effort 1387654 355239424
1 3/1 Expedite 7399108 1011085824
Best-Effort 11823344 3026776064
1 4/1 Expedite 0 0
Best-Effort 0 0
2 1/1 Expedite 0 0
Best-Effort 0 0
2 2/1 Expedite 0 0
Best-Effort 0 0
===============================================================================
Sample Output Egress per-ingress-fp-stats interval repeat
rate
# monitor card 1 fp 1 egress per-ingress-fp-stats interval 11 repeat 1 rate
===============================================================================
Card 1 FP 1 TAP 1 Egress Per-Ingress FP Statistics
===============================================================================
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
To FP/TAP Priority Received Packets Received Octets
-------------------------------------------------------------------------------
1 1/1 Expedite 172437 2207203840
Best-Effort 12345678 3160493568
1 2/1 Expedite 103446 1324118016
Best-Effort 987654 252839424
1 3/1 Expedite 6899108 883085824
Best-Effort 11223344 2873176064
1 4/1 Expedite 0 0
Best-Effort 0 0
2 1/1 Expedite 0 0
Best-Effort 0 0
2 2/1 Expedite 0 0
Best-Effort 0 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 11 sec (Mode: Rate)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
To FP/TAP Priority Received Packets Received Octets Mbps
-------------------------------------------------------------------------------
1 1/1 Expedite 100000 25600000 19
Best-Effort 200000 51200000 37
1 2/1 Expedite 300000 76800000 56
Best-Effort 400000 102400000 74
1 3/1 Expedite 500000 128000000 93
Best-Effort 600000 153600000 112
1 4/1 Expedite 0 0
Best-Effort 0 0
2 1/1 Expedite 0 0
Best-Effort 0 0
2 2/1 Expedite 0 0
Best-Effort 0 0
===============================================================================
card
Syntax
card slot-number fp fp-number queue-group queue-group-name instance instance-id [ingress] [access | networks] [interval seconds] [repeat repeat] [absolute | percent-rate [reference-rate]] [arbiter root | name]
Context
[Tree] (monitor>qos>arbiter-stats card)
Full Context
monitor qos arbiter-stats card
Description
This command monitors arbiter statistics in an ingress FP queue group.
Parameters
- slot-number
-
Specifies the slot number associated with the queue group, expressed as an integer.
- fp-number
-
Specifies the FP number associated with the queue group, expressed as an integer.
- ingress
-
Displays policer statistics applied on the ingress FP.
- access
-
Displays policer statistics on the FP access.
- network
-
Displays policer statistics on the FP network.
- queue-group-name
-
Specifies the name of the queue group up to 32 characters.
- instance-id
-
Specifies the identification of a specific instance of the queue-group.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
When the absolute keyword is specified, the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
- percent-rate
-
When the percent-rate keyword is specified, the rate-per-second for each statistic is displayed based on the reference rate of 10G.
- reference-rate
-
When a reference-rate value is specified, the rate-per-second for each statistic is displayed as a percentage based on the reference rate specified.
- name
-
Specify the name of the policer control policy arbiter.
- root
-
Specifies the root arbiter.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
card
Syntax
card slot-number fp fp-number ingress [access | network] queue-group queue-group-name [instance instance-id] [arbiter {name | root}]
Context
[Tree] (clear>qos>arbiter-stats card)
Full Context
clear qos arbiter-stats card
Description
This command clears arbiter statistics per card.
Parameters
- slot-number
-
Specifies the slot number associated with the queue group.
- fp-number
-
Specifies the FP number associated with the queue group.
- access
-
Clears policer statistics on the FP access.
- network
-
Clears policer statistics on the FP network.
- queue-group-name
-
Specifies the queue group name, up to 32 characters.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
card
Syntax
card slot-number fp fp-number ingress [access | network] [queue-group queue-group-name] [instance instance-id] [arbiter name | root]
Context
[Tree] (show>qos>arbiter-stats card)
Full Context
show qos arbiter-stats card
Description
This command displays the arbiter statistics per card.
Parameters
- slot-number
-
Displays information for the specified card slot.
- fp-number
-
Specifies the FP number associated with the queue group.
- access
-
Displays arbiter statistics applied on an access port.
- network
-
Displays arbiter statistics applied on a network port.
- queue-group-name
-
Specifies the queue group name, up to 32 characters.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
card
Syntax
card slot-number fp fp-number queue-group group-name instance instance-id {access | network} [detail] [ingress]
Context
[Tree] (show>qos>policer card)
Full Context
show qos policer card
Description
This command displays the policer statistics per card.
Parameters
- slot-number
-
Displays information for the specified card slot.
- fp-number
-
Specifies the FP number associated with the queue group.
- group-name
-
Specifies the queue group name, up to 32 characters.
- access
-
Displays policer statistics applied on an access port.
- network
-
Displays policer statistics applied on a network port.
- detail
-
Displays detailed information.
- ingress
-
Displays ingress queue group information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
card-status
card-status
Syntax
card-status
Context
[Tree] (tools>dump>service>id>fdb card-status)
Full Context
tools dump service id fdb card-status
Description
This command displays the following MAC address information for each line card in the system:
-
the number of allocated MAC addresses
-
the number of pending MAC address allocations
-
the number of pending free MAC addresses
Platforms
All
Output
Sample Output*A:PE1# tools dump service id 1 fdb card-status
===============================================================================
VPLS FDB Card Status at 01/31/2017 08:44:38
===============================================================================
Card Allocated PendAlloc PendFree
-------------------------------------------------------------------------------
1 4 0 0
2 4 0 0
5 4 0 0
===============================================================================
*A:PE1#
category-map
category-map
Syntax
category-map [category-map]
category-map category-map subscribers
Context
[Tree] (show>subscr-mgmt category-map)
Full Context
show subscriber-mgmt category-map
Description
This command displays category map information.
With no parameters specified, a summary view of all configured category maps is displayed.
With the optional category-map name parameter specified, the detailed configuration of the specified category map name is displayed.
With the category-map subscribers parameters specified, all subscribers that have the specified category-map associated are displayed.
Parameters
- category-map
-
Specifies the category map name for which information is displayed.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example of subscriber management category map information.
Sample OutputNode# show subscriber-mgmt category-map "cat-map-1"
===============================================================================
Category Map: cat-map-1
===============================================================================
Description : gy - time and volume
Credit Type : volume Credit Exh. Thresh.: 80%
Activity Thresh. : 0 kb/s
Gx session level
usage monitoring : false
-------------------------------------------------------------------------------
Category: cat-1-time
-------------------------------------------------------------------------------
Description : Rating group for Time quota
Credit Type Over. : none Rating Group : 11
OutOfCredit Action : none
Default Credit : none
Ingress Queues : 1
Egress Queues : 1
Ingress Policers : none
Egress Policers : none
ExhCrdSvcLvl Pir : none
-------------------------------------------------------------------------------
Category: cat-1-volume
-------------------------------------------------------------------------------
Description : Rating group for Volume quota
Credit Type Over. : none Rating Group : 12
OutOfCredit Action : none
Default Credit : none
Ingress Queues : 1
Egress Queues : 1
Ingress Policers : none
Egress Policers : none
ExhCrdSvcLvl Pir : 100
===============================================================================
Category Map Field Descriptions describes category map output fields.
Field |
Description |
---|---|
Description |
The user provided description of this policy |
Credit Type |
The volume or time based accounting is performed |
Credit Exh. Thresh |
The credit exhaust threshold considered to take action |
Activity Thresh. |
The threshold (in kb/s) that is applied to determine whether or not activity is occurring |
Gx session level usage monitoring |
Whether category map supports Gx session level usage monitoring |
Credit Type Over. |
Credit type override |
Rating Group |
The rating group applicable for this category |
OutOfCredit Action |
The action to be taken if the credit es exhausted |
Default Credit |
The default value for the Time credit |
Ingress Queues |
The ingress queues defined in this category |
Egress Queues |
The egress queues defined in this category |
Ingress Policers |
The ingress policers defined in this category |
Egress Policers |
The egress queues defined in this category |
ExhCrdSvcLvl Pir |
The credit exhaust threshold considered to take action |
category-set-id
category-set-id
Syntax
category-set-id category-set
Context
[Tree] (show>app-assure>web-service category-set-id)
Full Context
show application-assurance web-service category-set-id
Description
This command displays information for the web-service category set.
Parameters
- category-set
-
Specifies the category set ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output examples show information about SAPs using the application profile.
Example Output# show application-assurance web-service category-set-id 1
===============================================================================
Compatible Classifier-ids
===============================================================================
Name Description
-------------------------------------------------------------------------------
web-sevice-1 WebTitan Web Filtering
===============================================================================
ccrt-replay
ccrt-replay
Syntax
ccrt-replay [session-id session-id] [diameter-application-policy name]
ccrt-replay diameter-application-policy name summary
ccrt-replay summary
Context
[Tree] (show>subscr-mgmt>diam-session ccrt-replay)
Full Context
show subscriber-mgmt diameter-session ccrt-replay
Description
This command displays:
-
information for all diameter sessions that are in CCR-T replay mode:
-
Diameter session ID
-
Diameter Application Policy
-
Replay Time left
-
-
statistics per diameter application policy for diameter sessions in CCR-T replay mode or that were in CCR-T replay mode and were dropped or terminated:
-
Sessions in CCR-T replay mode: the number of Diameter Gx or Gy sessions from the specified diameter application policy that are currently in CCR-T replay mode
-
Replay sessions dropped (maximum life-time expired): the number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and got dropped because no CCA-t was received before max-lifetime expiration
-
Replay sessions dropped (to free resources): the number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and got dropped because the maximum number of active Diameter sessions for Gx or Gy was reached
-
Replay sessions dropped (cleared): the number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and got dropped because the operator issued a clear subscriber-mgmt diameter-session ccrt-replay diameter-application-policy name sessions command
-
Replay sessions terminated (CCA-T received): the number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and for which a CCA-t was received before max-lifetime expiration
-
Statistics last cleared time: timestamp when the statistics were last cleared or n/a if the statistics were never cleared
-
Parameters
- name
-
Specifies the application policy, up to 32 characters.
- session-id
-
Specifies a diameter session ID.
- summary
-
Displays summarized information about CCR-T replay.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example of subscriber management CCR-T replay information.
Sample Output*A:Dut-C# show subscriber-mgmt diameter-session ccrt-replay
===============================================================================
Diameter Sessions in CCR-t Replay Mode
===============================================================================
Session-id Replay Time Left
Diameter Application Policy
-------------------------------------------------------------------------------
router.workstation.be;1431089354;13
diamapppol_gx 0d 21:21:46
bng.nokia.com;1537773225;4
diam-gy-1 0d 00:59:16
-------------------------------------------------------------------------------
No. of Matching Entries: 2
===============================================================================
*A:Dut-C# show subscriber-mgmt diameter-session ccrt-replay session-id ro
===============================================================================
Diameter Sessions in CCR-t Replay Mode
===============================================================================
Session-id Replay Time Left
Diameter Application Policy
-------------------------------------------------------------------------------
router.workstation.be;1431089354;13
diamapppol_gx 0d 21:21:27
-------------------------------------------------------------------------------
No. of Matching Entries: 1
===============================================================================
*A:Dut-C# show subscriber-mgmt diameter-session ccrt-replay summary
===============================================================================
Diameter Sessions in CCR-t Replay Mode
===============================================================================
Total Count : 2
===============================================================================
*A:Dut-C# show subscriber-mgmt diameter-session ccrt-replay diameter-application-policy "diam-gy-1"
===============================================================================
Diameter Sessions in CCR-T Replay Mode
===============================================================================
Session-id Replay Time Left
Diameter Application Policy
-------------------------------------------------------------------------------
bng.nokia.com;1537773225;6
diam-gy-1 0d 00:58:33
-------------------------------------------------------------------------------
No. of Matching Entries: 1
===============================================================================
===============================================================================
Diameter CCR-T Replay status for policy "diam-gy-1"
===============================================================================
Sessions in CCR-T replay mode : 1
Replay sessions dropped (maximum life-time expired) : 0
Replay sessions dropped (to free resources) : 0
Replay sessions dropped (cleared) : 0
Replay sessions terminated (CCA-T received) : 1
Statistics last cleared time : N/A
===============================================================================
CCR-T Replay Field Descriptions describes CCRT replay output fields.
Field |
Description |
---|---|
Session-id |
The diameter session ID that is in CCR-T replay mode |
Diameter Application Policy |
The diameter application policy name to which the Gx or Gy session in CCR-T replay mode belongs |
Replay Time Left |
The remaining max-lifetime before the Diameter Gx or Gy session in CCR-T replay mode is dropped |
No. of Matching Entries |
The number of entries matching the search criteria |
Sessions in CCR-T replay mode |
The number of Diameter Gx or Gy sessions from the specified diameter application policy that are in CCR-T replay mode |
Replay sessions dropped (maximum life-time expired) |
The number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and got dropped because no CCA-t was received before max-lifetime expiration |
Replay sessions dropped (to free resources) |
The number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and got dropped because the maximum number of Diameter sessions was reached |
Replay sessions dropped (cleared) |
The number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and got dropped because the operator issued a clear subscriber-mgmt diameter-session ccrt-replay diameter-application-policy name sessions command |
Replay sessions terminated (CCA-T received) |
The number of Diameter Gx or Gy sessions from the specified diameter application policy that were in CCR-T replay mode and for which a CCA-t was received before max-lifetime expiration |
Statistics last cleared time |
The timestamp when the statistics were last cleared or n/a if the statistics were never cleared |
ccrt-replay
Syntax
ccrt-replay diameter-application-policy name statistics
ccrt-replay diameter-application-policy name sessions
Context
[Tree] (clear>subscr-mgmt>diam-session ccrt-replay)
Full Context
clear subscriber-mgmt diameter-session ccrt-replay
Description
This command, when the statistics parameter is specified, clears the CCR-T replay statistics and updates the "Statistics last cleared time” value.
This command, when the sessions parameter is specified, drops the diameter Gx or Gy sessions that are in CCR-T replay mode.
Parameters
- name
-
Specifies the diameter application policy, up to 32 characters.
- statistics
-
Clears the CCR-T replay statistics.
- sessions
-
Clears the sessions that are in CCR-T replay mode.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
cem
cem
Syntax
cem
Context
[Tree] (clear>service>statistics>id cem)
Full Context
clear service statistics id cem
Description
This command clears CEM statistics for this service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
cert-profile
cert-profile
Syntax
cert-profile name association
cert-profile [name]
cert-profile name entry [value]
Context
[Tree] (show>ipsec cert-profile)
Full Context
show ipsec cert-profile
Description
This command displays IPsec certificate profile information.
Parameters
- name
-
Specifies an existing certificate profile name.
- association
-
Displays information for which this IPsec certificate profile is associated.
- value
-
Displays information for the specified entry.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example output of the show ipsec cert-profile command.
Sample Output*A:Dut-A# show ipsec cert-profile cert "cert-1.der"
==============================================================================
Certificate Profile Entry
==============================================================================
Id Cert Key Status Flags
------------------------------------------------------------------------------
1 cert-1.der key-1.der
==============================================================================
*A:Dut-A#
*A:Dut-A# show ipsec cert-profile "cert-1.der" entry 1
===============================================================================
IPsec Certificate Profile: cert-1.der Entry: 1 Detail
===============================================================================
Cert File : cert-1.der
Key File : key-1.der
Status Flags : (Not Specified)
Comp Chain : complete
Compute Chain CA Profiles
-------------------------------------------------------------------------------
CA10
CA9
CA8
CA7
CA6
===============================================================================
*A:Dut-A#
cert-profile
Syntax
cert-profile [name]
cert-profile name association
cert-profile name entry entry
Context
[Tree] (show>system>security>tls cert-profile)
Full Context
show system security tls cert-profile
Description
This command displays information about server and client profiles that are using this certificate profile.
Parameters
- entry
-
Specifies a certificate profile entry number for which to display information.
- name
-
Specifies the name of a certificate profile for which to display information.
Platforms
All
certificate
certificate
Syntax
certificate filename association
Context
[Tree] (show>ipsec certificate)
[Tree] (show certificate)
Full Context
show ipsec certificate
show certificate
Description
This command displays certificate-related information.
Parameters
- filename
-
Specifies the certificate file name.
- association
-
Displays information for which this IPsec certificate is associated.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
- show ipsec certificate
All
- show certificate
Output
The following is an example output of the show certificate command.
Sample Output*A:Dut-B# show certificate ca-profile
-------------------------------------------------------------------------------
Max Cert Chain Depth: 7 (default)
-------------------------------------------------------------------------------
Certificate Display Format: 1 ASCII
===============================================================================
CA Profile
===============================================================================
CA Profile Admin Oper Cert File CRL File
State State
-------------------------------------------------------------------------------
CA0 up up CA1-00cert.der CA1-00crl.der
CA1 up up CA1-01cert.der CA1-01crl.der
CA2 up up CA1-02cert.der CA1-02crl.der
CA3 up up CA1-03cert.der CA1-03crl.der
CA4 up up CA1-04cert.der CA1-04crl.der
CA5 up up rsa_sha512_1024_0cert.d* rsa_sha512_1024_0crl.der
CA6 up up rsa_sha512_1024_1cert.d* rsa_sha512_1024_1crl.der
CA7 up up rsa_sha512_1024_2cert.d* rsa_sha512_1024_2crl.der
CA8 up up rsa_sha512_1024_3cert.d* rsa_sha512_1024_3crl.der
CA9 up up rsa_sha512_1024_4cert.d* rsa_sha512_1024_4crl.der
CA10 up up rsa_sha512_1024_5cert.d* rsa_sha512_1024_5crl.der
CA11 up up rsa_sha384_1024_0cert.d* rsa_sha384_1024_0crl.der
CA12 up up rsa_sha384_1024_1cert.d* rsa_sha384_1024_1crl.der
CA13 up up rsa_sha384_1024_2cert.d* rsa_sha384_1024_2crl.der
CA14 up up rsa_sha384_1024_3cert.d* rsa_sha384_1024_3crl.der
CA15 up up rsa_sha384_1024_4cert.d* rsa_sha384_1024_4crl.der
CA16 up up rsa_sha384_1024_5cert.d* rsa_sha384_1024_5crl.der
CMPv2 up up rsaCMPv2cert.der rsaCMPv2CRL.der
-------------------------------------------------------------------------------
Entries found: 18
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-B#
*A:Dut-B# show ipsec certificate cert-1.der association
===============================================================================
Associated Tunnels
===============================================================================
Tunnel SvcId Sap Admin
-------------------------------------------------------------------------------
tun-1-s-cert-v2 3 tunnel-1.private:3 Up
tun-1-s-cert-MTA-v2 8 tunnel-1.private:7 Up
tun-1-s-cert-i_op-ss-v2 42 tunnel-1.private:10 Up
tun-1-s-cert-MTA-i_op-ss-v2 48 tunnel-1.private:11 Up
-------------------------------------------------------------------------------
IPsec Tunnels: 4
===============================================================================
*A:Dut-B#
In the following example, the "cert-1.der" is the certificate-profile name, whereas above the cert-1.der is the actual file in use.
*A:Dut-B# show ipsec cert-profile association "cert-1.der"
===============================================================================
IPsec tunnels using certificate profile
===============================================================================
SvcId Type SAP Tunnel
-------------------------------------------------------------------------------
3 vprn tunnel-1.private:3 tun-1-s-cert-v2
8 vprn tunnel-1.private:7 tun-1-s-cert-MTA-v2
42 vprn tunnel-1.private:10 tun-1-s-cert-i_op-ss-v2
48 vprn tunnel-1.private:11 tun-1-s-cert-MTA-i_op-ss-v2
===============================================================================
Number of tunnel entries: 4
===============================================================================
===============================================================================
IPsec gateways using certificate profile
===============================================================================
SvcId Type SAP Gateway
-------------------------------------------------------------------------------
1057 vprn tunnel-1.public:18 d-cert-MTA-g1-1-v2
1092 vprn tunnel-1.public:21 d-cert-i_op-ss-g1-1-v2
===============================================================================
Number of gateway entries: 2
===============================================================================
*A:Dut-B#
show ipsec gateway tunnel 10.2.2.100:500
===============================================================================
IPsec Remote Users Tunnel Detail
===============================================================================
IP Addr: 10.2.2.100:500, port: 500
-------------------------------------------------------------------------------
Service Id : 300 Sap Id : tunnel-1.public:100
Address : 10.2.2.100:500
Private If : priv
Private Address : 10.20.20.50
Private Service : 400 Template Id : 1
Replay Window : None Bi Direction SA : true
Host MDA : 1/2
Match TrustAnchor: labroot
Last Oper Changed: 05/04/2016 17:36:20
IKE IDI Type : derAsn1Dn
IKE IDI Value : CN=Client-1
-------------------------------------------------------------------------------
Dynamic Keying Parameters
-------------------------------------------------------------------------------
Transform Id1 : 1 Transform Id2 : None
Transform Id3 : None Transform Id4 : None
IPsec GW Name : rw
Local GW Address : 172.16.100.1
Ike Policy Id : 1 Ike Pol Auth : cert
Pre Shared Key : None
Cert Profile : segw
Trust Anchor Prof: labroot
Selected Cert : segw-1.cert
Selected Key : segw-1.key
Send Chain Prof : None
Local Id Type : none
Client Database
Name : (Not Specified)
Client ID : None
Radius Acct Plcy : None
Radius Auth Plcy : None
TS-List : <none>
Certificate Status Verify
-------------------------------------------------------------------------------
Primary : crl Secondary : none
Default Result : good
DHCP
-------------------------------------------------------------------------------
Admin State : Up Send Release : true
Service : 400
Gi-Address : 10.20.20.1
Server1-Address : 10.9.9.9
DHCPv4 Lease
-------------------------------------------------------------------------------
Private Address : 10.20.20.50
Acquired : 2016/05/04 17:36:19 UTC
Renew : 2016/05/04 18:06:19 UTC
Rebind : 2016/05/04 18:28:49 UTC
Valid Lifetime
End : 2016/05/04 18:36:19 UTC
Total : 3600 seconds
Remaining : 3585 seconds
Server : 10.9.9.9
-------------------------------------------------------------------------------
ISAKMP-SA
-------------------------------------------------------------------------------
State : Up
Established : 05/04/2016 17:36:20 Lifetime : 86400
Expires : 05/05/2016 17:36:20
ISAKMP Statistics
--------------------
Tx Packets : 2 Rx Packets : 2
Tx Errors : 0 Rx Errors : 0
Tx DPD : 0 Rx DPD : 0
Tx DPD ACK : 0 Rx DPD ACK : 0
DPD Timeouts : 0 Rx DPD Errors : 0
-------------------------------------------------------------------------------
IPsec-SA : 1, Inbound (index 2)
-------------------------------------------------------------------------------
SPI : 207232
Auth Algorithm : Sha1 Encr Algorithm : Aes128
Installed : 05/04/2016 17:36:20 Lifetime : 3600
Local Traffic Selectors:
10.9.9.9-10.9.9.9
any protocol
Remote Traffic Selectors:
10.20.20.50-10.20.20.50
any protocol
Aggregate Statistics
--------------------
Bytes Processed : 0 Packets Processed: 0
Crypto Errors : 0 Replay Errors : 0
SA Errors : 0 Policy Errors : 0
-------------------------------------------------------------------------------
IPsec-SA : 1, Outbound (index 1)
-------------------------------------------------------------------------------
SPI : 3433111520
Auth Algorithm : Sha1 Encr Algorithm : Aes128
Installed : 05/04/2016 17:36:20 Lifetime : 3600
Local Traffic Selectors:
10.9.9.9-10.9.9.9
any protocol
Remote Traffic Selectors:
10.20.20.50-10.20.20.50
any protocol
Aggregate Statistics
--------------------
Bytes Processed : 0 Packets Processed: 0
Crypto Errors : 0 Replay Errors : 0
SA Errors : 0 Policy Errors : 0
===============================================================================
Fragmentation Statistics
===============================================================================
Encapsulation Overhead : 73
Pre-Encapsulation
Fragmentation Count : 0
Last Fragmented Packet Size : 0
Post-Encapsulation
Fragmentation Count : 0
Last Fragmented Packet Size : 0
===============================================================================
===============================================================================
certificate-profile
certificate-profile
Syntax
certificate-profile
Context
[Tree] (show>app-assure>group certificate-profile)
Full Context
show application-assurance group certificate-profile
Description
This command displays certificate profile information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
cflowd
cflowd
Syntax
cflowd
Context
[Tree] (show cflowd)
Full Context
show cflowd
Description
This command displays cflowd information.
Platforms
All
cflowd
Syntax
cflowd
Context
[Tree] (show>app-assure>group cflowd)
Full Context
show application-assurance group cflowd
Description
Commands in this context display cflowd output.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
cflowd
Syntax
cflowd
Context
[Tree] (clear cflowd)
Full Context
clear cflowd
Description
This command clears the raw and aggregation flow caches which are sending flow data to the configured collectors. This action will trigger all the flows to be discarded. The cache restarts flow data collection from a fresh state. This command also clears global stats collector stats listed in the cflowd show commands.
Platforms
All
cflowd
Syntax
cflowd
Context
[Tree] (tools>dump cflowd)
Full Context
tools dump cflowd
Description
Commands in this context dump Cflowd information.
Platforms
All
cflowd
Syntax
cflowd
Context
[Tree] (tools>perform cflowd)
Full Context
tools perform cflowd
Description
Commands in this context perform Cflowd operations.
Platforms
All
cflowd
Syntax
cflowd
Context
[Tree] (clear>app-assure>group cflowd)
Full Context
clear application-assurance group cflowd
Description
This command clears cflowd application assurance statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
cfm-stack-table
cfm-stack-table
Syntax
cfm-stack-table [all-ports] [level level] [direction { up | down}] [primary-vlan-enabled vlan-id]
cfm-stack-table [{all-sdps | all-virtuals}] [level level] [direction {up | down}] [primary-vlan-enabled vlan-id]
cfm-stack-table facility [{all-ports | all-port-meps | all-lags | all-lag-meps | all-tunnel-meps | all-router-interfaces}] [level level] [direction { up | down}]
cfm-stack-table facility collect-lmm-stats
cfm-stack-table facility lag lag-id [tunnel tunnel-id] [level level] [direction {up | down]
cfm-stack-table facility port port-id [tunnel tunnel-id] [level level] [ direction {up | down}]
cfm-stack-table facility router-interface interface-name [level level] [direction {up | down]
cfm-stack-table port port-id [ vlan qtag[.qtag]] [level level] [direction {up | down}] [primary-vlan-enabled vlan-id]
cfm-stack-table sdp sdp-id[:vc-id] [level level] [direction {up | down}] [primary-vlan-enabled vlan-id]
cfm-stack-table virtual service-id [level level]
Context
[Tree] (show>eth-cfm cfm-stack-table)
Full Context
show eth-cfm cfm-stack-table
Description
This command displays stack-table information. This stack-table is used to display the various management points MEPs and MIPs that are configured on the system. These can be service-based or facility-based. The various options allow the operator to be specific. If no parameters are included then the entire stack-table is displayed.
Parameters
- port port-id
-
Displays the bridge port or aggregated port on which MEPs or MHFs are configured.
- vlan vlan-id
-
Displays the associated VLAN ID.
- level
-
Displays the MD level of the maintenance point.
- collect-lmm-stats
-
Displays facility MEPs on which LMM collection is enabled.
- direction up | down
-
Displays the direction in which the MP faces on the bridge port.
- facility
-
Displays the CFM stack table information for facility MEPs. The base command displays all the facility MEPs. Options may be included in order to further parse the table for specific facility MEP information.
- sdp sdp-id[:vc-id]
-
Displays CFM stack table information for the specified SDP.
- virtual service-id
-
Displays CFM stack table information for the specified SDP.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following is an example of stack table information. ETH-CFM CFM Stack Table Field Descriptions describes the output content.
Sample Outputshow eth-cfm cfm-stack-table
===============================================================================
CFM Stack Table Defect Legend:
R = Rdi, M = MacStatus, C = RemoteCCM, E = ErrorCCM, X = XconCCM
A = AisRx, L = CSF LOS Rx, F = CSF AIS/FDI rx, r = CSF RDI rx
G = receiving grace PDU (MCC-ED or VSM) from at least one peer
===============================================================================
CFM SAP Stack Table
===============================================================================
Sap Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
1/2/1:51.28 2 D 12 5001 28 d8:1c:01:02:00:01 --C---- -
1/2/1:1000.1000 3 U 13 1000 28 00:00:00:00:00:28 ---E--- -
1/2/1:1001.1001 1 B 0 0 MIP d8:1c:01:02:00:01 ------- -
1/2/1:1500.1500 3 U 13 1500 28 00:00:00:00:00:28 ------- -
1/2/1:2000.2000 3 U 13 2000 128 d8:1c:01:02:00:01 ------- -
1/2/1:2000.2000 4 B 14 2000 MIP 00:00:00:00:01:28 ------- -
1/2/1:3000.3000 4 B 0 0 MIP d8:1c:01:02:00:01 ------- -
1/2/1:4000.* 3 U 13 4000 28 00:00:00:00:00:28 ------- -
1/2/1:4001.* 3 U 13 4001 28 00:00:00:00:00:28 ------- -
1/2/1:4001.* 4 D 14 4001 28 00:00:00:00:00:28 ------- -
===============================================================================
===============================================================================
CFM Ethernet Tunnel Stack Table
===============================================================================
Eth-tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
CFM Ethernet Ring Stack Table
===============================================================================
Eth-ring Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
CFM Facility Port Stack Table
===============================================================================
Port Tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
1/1/1 0 0 D 10 1 28 d8:1c:01:01:00:01 ------- -
===============================================================================
===============================================================================
CFM Facility LAG Stack Table
===============================================================================
Lag Tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
CFM Facility Tunnel Stack Table
===============================================================================
Port/Lag Tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
CFM Facility Interface Stack Table
===============================================================================
Interface Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
v28-v29-1/1/6 2 D 12 1 28 00:00:00:00:00:28 ------- -
===============================================================================
===============================================================================
CFM SAP Primary VLAN Stack Table
===============================================================================
Sap
Primary VlanId Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
1/1/10:2002.*
2002 3 U 13 2002 28 00:00:00:00:00:28 ------- -
1/2/1:4000.*
4000 4 B 14 4000 MIP d8:1c:01:02:00:01 ------- -
4000 5 B 15 4000 MIP d8:1c:01:02:00:01 ------- -
===============================================================================
===============================================================================
CFM SDP Stack Table
===============================================================================
Sdp Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
2829:4001 2 D 12 4001 28 00:00:00:00:00:28 ------- -
===============================================================================
===============================================================================
CFM SDP Primary VLAN Stack Table
===============================================================================
Sdp
Primary VlanId Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
2829:4000
4000 2 D 12 4000 28 00:00:00:00:00:28 ------- -
4000 4 B 14 4000 MIP d8:1c:ff:00:00:00 ------- -
4000 5 B 15 4000 MIP d8:1c:ff:00:00:00 ------- -
===============================================================================
===============================================================================
CFM Virtual Stack Table
===============================================================================
Service Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
100 4 U 14 100 28 00:00:00:00:00:28 ------- -
1000 4 U 14 1000 28 d8:1c:ff:00:00:00 ---E--- -
2000 3 U 13 2000 28 00:00:00:00:00:28 ------- -
3000 3 U 13 3000 28 00:00:00:00:00:28 R-C---- -
===============================================================================
Label |
Description |
---|---|
Sap |
Displays associated SAP IDs. |
Sdp |
Displays the SDP binding for the bridge. |
Level Dir |
Displays the MD level of the maintenance point. |
Md-index |
Displays the maintenance domain (MD) index. |
Ma-index |
Displays the maintenance association (MA) index. |
Mep-id |
Displays the integer that is unique among all the MEPs in the same MA. |
Mac-address |
Displays the MAC address of the MP. |
change-key
change-key
Syntax
change-key authentication authentication-protocol old-authentication-key new-authentication-key
change-key authentication authentication-protocol privacy privacy-protocol old-privacy-key new-privacy-key
Context
[Tree] (tools>perform>system>mgmt-itf>snmp change-key)
Full Context
tools perform system management-interface snmp change-key
Description
This command generates KeyChange strings to change SNMPv3 authentication or privacy keys. The SNMP engine ID is not needed because localized keys are required as input. The KeyChange algorithm uses a random string, which generates a different output each time the command is executed.
Parameters
- authentication
-
Generates a KeyChange string for an authentication key.
- authentication-protocol
-
Specifies the SNMPv3 authentication protocol.
- old-authentication-key
-
Specifies the old localized authentication key.
- new-authentication-key
-
Specifies the new localized authentication key.
- privacy
-
Keyword to generate a KeyChange string for a privacy key.
- privacy-protocol
-
Specifies the SNMPv3 privacy protocol.
- old-privacy-key
-
Specifies the old localized privacy key.
- new-privacy-key
-
Specifies the new localized privacy key.
Platforms
All
Output
The following output is an example of a generated KeyChange string.
Sample OutputA:ALA-1# tools perform system management-interface snmp change-key authentication hmac-sha1-96 5c9ccb02cb2066f226e9d41b428c63ba801a3319
6caf2644ebb8141876a455ba14e58d5c61d8cb16
KeyChange string : 8feb0fa890f3607aa0986e7f0a71d3d889da1d3f1f07933770e50639c0770cca4dc0519637796240
channel
channel
Syntax
channel [router router-instance | vpls service-id | service-name service-name] [fp slot-number[/fp-number]] [group ip-address [source ip-address]] [path path-type] [detail]
Context
[Tree] (show>mcast-management channel)
Full Context
show mcast-management channel
Description
This command displays multicast path management channel related information.
Parameters
- service-id
-
Specifies an existing VPLS service ID.
- service-name
-
A string up to 64 characters.
- slot-number
-
Displays information for the specified card slot.
- fp-number
-
Specifies an FP.
- ip-address
-
ipv4-address in the form a.b.c.d
- path-type
-
Specifies the path type.
Platforms
7450 ESS, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-7/12/12e, 7750 SR-s, 7950 XRS, VSR
Output
The following output displays an example of multicast management channel information.
Sample Output*A:PE# show mcast-management channel
===============================================================================
Multicast Channels
===============================================================================
Legend : D - Dynamic E - Explicit
===============================================================================
Source Address Slot/Fp Current-Bw Path D/E
Group Address Highest-Bw Plane
-------------------------------------------------------------------------------
10.0.0.29 5/1 3930 Primary D
233.252.0.1 3973 17
===============================================================================
Multicast Channels : 1
===============================================================================
*A:PE# show mcast-management channel detail
===============================================================================
Multicast Channels
===============================================================================
-------------------------------------------------------------------------------
Source Address : 10.0.0.29
Group Address : 233.252.0.1
-------------------------------------------------------------------------------
Slot/Complex : 5/1 Current Bw : 3918 kbps
Dynamic/Explicit : Dynamic Current Path : Primary
Oper Admin Bw : 0 kbps Current Plane : 17
Ing last highest : 3973 Preference : 0
Black-hole rate : None Ing sec highest : 3970
Time remaining : 20 seconds Blackhole : No
===============================================================================
Multicast Channels : 1
===============================================================================
*A:PE#
channel
Syntax
channel [service service-id] [interface ip-int-name] [address mcast-address] [source ip-address] [detail]
Context
[Tree] (show>video>adi channel)
Full Context
show video adi channel
Description
This command displays video channel information.
Parameters
- service service-id
-
Displays video channel information pertaining to the specified service ID.
- interface ip-int-name
-
Displays video channel information pertaining to the specified interface.
- address mcast-address
-
Displays video channel information pertaining to the specified multicast channel address.
- source ip-address
-
Displays video channel information pertaining to the source IP address.
- detail
-
The output displays detailed video channel information.
Platforms
7450 ESS, 7750 SR-1, 7750 SR-7/12/12e, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
channel
Syntax
channel [service service-id] [interface ip-int-name] [address mcast-address] [source ip-address] [summary | detail] [pid | config | [analyzer [interval time-interval]]]
Context
[Tree] (show>video channel)
Full Context
show video channel
Description
This command displays video channel information.
Parameters
- service service-id
-
Displays video channel information pertaining to the specified service ID.
- interface ip-int-name
-
Displays video channel information pertaining to the specified interface.
- address mcast-address
-
Displays video channel information pertaining to the specified multicast channel address.
- source ip-address
-
Displays video channel information pertaining to the source IP address.
- summary
-
The output displays summarized video channel information.
- detail
-
The output displays detailed video channel information.
Platforms
7450 ESS, 7750 SR-1, 7750 SR-7/12/12e, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
Output
The following is an example output for this command.
Sample Output*A:SR-12/Dut-C# show video channel analyzer
===============================================================================
Video channel analyzer summary
===============================================================================
Channel number : 1
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
MDI Delay Factor : 7 MDI Loss Rate : 0
Good Secs : 54
-------------------------------------------------------------------------------
Channel number : 2
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
MDI Delay Factor : 6 MDI Loss Rate : 0
Good Secs : 54
-------------------------------------------------------------------------------
Channel number : 3
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.7 Source Address : 10.20.13.3
MDI Delay Factor : 7 MDI Loss Rate : 0
Good Secs : 54
-------------------------------------------------------------------------------
Number of channels : 3
===============================================================================
*A:SR-12/Dut-C#
*A:SR-12/Dut-C# show video channel analyzer address 192.0.2.6 source 10.20.13.2 interface "video-300" detail
===============================================================================
Video channel analyzer detail
===============================================================================
Channel number : 1
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
MDI Delay Factor : 8 MDI Loss Rate : 0
Good Secs : 80
===============================================================================
GOP Stats
===============================================================================
Min Max Avg
-------------------------------------------------------------------------------
GOP Length 40 78 48
Frames/Sec 39 55 53
===============================================================================
Frame Stats
===============================================================================
I-Frame P-Frame B-Frame
-------------------------------------------------------------------------------
Good 19 986 0
Bad 0 0 0
===============================================================================
Error Stats
===============================================================================
POA Events QoS Events TNC Events
-------------------------------------------------------------------------------
PAT Rep 0 0 0
PMT Rep 0 0 0
PCR Rep 0 0 0
PAT Syntax Err - - 0
PMT Syntax Err - - 0
Sync Byte Err - 0 -
Sync Loss 0 - -
Unref PID - - 0
Traffic Loss 0 - -
-------------------------------------------------------------------------------
Overall 0 0 0
-------------------------------------------------------------------------------
Reoccuring events only increment counter once every second
-------------------------------------------------------------------------------
Number of channels : 1
===============================================================================
*A:SR-12/Dut-C#
*A:SR-12/Dut-C# show video channel pid
===============================================================================
Video Channel PID
===============================================================================
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 0 PID Type : pat
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 2 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 126336
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 32 PID Type : video
MPEG Stream Type : 27 Is PCR PID : Yes
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 1952192
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 33 PID Type : pmt
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 308 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 126336
Number of pids for this channel: 5
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
PID : 0 PID Type : pat
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
PID : 2 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 126336
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
PID : 32 PID Type : video
MPEG Stream Type : 27 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 1949184
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
PID : 33 PID Type : pmt
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
PID : 308 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 136864
===============================================================================
*A:SR-12/Dut-C#
*A:SR-12/Dut-C# show video channel pid interface "video-300" source 10.20.13.3 address 192.0.2.5
===============================================================================
Video Channel PID
===============================================================================
No Matching Entries
===============================================================================
*A:SR-12/Dut-C# show video channel config
===============================================================================
Video channel config
===============================================================================
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
Analyzer State : Enabled Cc Error : Disabled
PAT Rep Err : Enabled TNC PAT Rep : 200
QOS PAT Rep : 400 POA PAT Rep : 600
PAT Syntax : Enabled PCR Rep Err : Enabled
TNC PCR Rep : 200 QOS PCR Rep : 400
POA PCR Rep : 600 Vid PID Absent : 1000
PID PMT Unref : Enabled PMT Rep Err Secs : Enabled
TNC PMT Rep : 400 QOS PMT Rep : 800
POA PMT Rep : 2000 PMT Syntax : Enabled
SCTE35 Err Secs : Disabled TEI Err Secs : Disabled
TS Sync Loss : Enabled Non-Vid Pid Abse*: 1000
Alarm Sev : tnc
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
Analyzer State : Enabled Cc Error : Disabled
PAT Rep Err : Enabled TNC PAT Rep : 200
QOS PAT Rep : 400 POA PAT Rep : 600
PAT Syntax : Enabled PCR Rep Err : Enabled
TNC PCR Rep : 200 QOS PCR Rep : 400
POA PCR Rep : 600 Vid PID Absent : 1000
PID PMT Unref : Enabled PMT Rep Err Secs : Enabled
TNC PMT Rep : 400 QOS PMT Rep : 800
POA PMT Rep : 2000 PMT Syntax : Enabled
SCTE35 Err Secs : Disabled TEI Err Secs : Disabled
TS Sync Loss : Enabled Non-Vid Pid Abse*: 1000
Alarm Sev : tnc
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.7 Source Address : 10.20.13.3
Analyzer State : Enabled Cc Error : Disabled
PAT Rep Err : Enabled TNC PAT Rep : 200
QOS PAT Rep : 400 POA PAT Rep : 600
PAT Syntax : Enabled PCR Rep Err : Enabled
TNC PCR Rep : 200 QOS PCR Rep : 400
POA PCR Rep : 600 Vid PID Absent : 1000
PID PMT Unref : Enabled PMT Rep Err Secs : Enabled
TNC PMT Rep : 400 QOS PMT Rep : 800
POA PMT Rep : 2000 PMT Syntax : Enabled
SCTE35 Err Secs : Disabled TEI Err Secs : Disabled
TS Sync Loss : Enabled Non-Vid Pid Abse*: 1000
Alarm Sev : tnc
-------------------------------------------------------------------------------
Number of channels : 3
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:SR-12/Dut-C#
*A:SR-12/Dut-C# show video channel config interface "video-300"
===============================================================================
Video channel config
===============================================================================
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.3
Analyzer State : Enabled Cc Error : Disabled
PAT Rep Err : Enabled TNC PAT Rep : 200
QOS PAT Rep : 400 POA PAT Rep : 600
PAT Syntax : Enabled PCR Rep Err : Enabled
TNC PCR Rep : 200 QOS PCR Rep : 400
POA PCR Rep : 600 Vid PID Absent : 1000
PID PMT Unref : Enabled PMT Rep Err Secs : Enabled
TNC PMT Rep : 400 QOS PMT Rep : 800
POA PMT Rep : 2000 PMT Syntax : Enabled
SCTE35 Err Secs : Disabled TEI Err Secs : Disabled
TS Sync Loss : Enabled Non-Vid Pid Abse*: 1000
Alarm Sev : tnc
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 192.168.2.1
Analyzer State : Enabled Cc Error : Disabled
PAT Rep Err : Enabled TNC PAT Rep : 200
QOS PAT Rep : 400 POA PAT Rep : 600
PAT Syntax : Enabled PCR Rep Err : Enabled
TNC PCR Rep : 200 QOS PCR Rep : 400
POA PCR Rep : 600 Vid PID Absent : 1000
PID PMT Unref : Enabled PMT Rep Err Secs : Enabled
TNC PMT Rep : 400 QOS PMT Rep : 800
POA PMT Rep : 2000 PMT Syntax : Enabled
SCTE35 Err Secs : Disabled TEI Err Secs : Disabled
TS Sync Loss : Enabled Non-Vid Pid Abse*: 1000
Alarm Sev : tnc
-------------------------------------------------------------------------------
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.7 Source Address : 10.20.13.3
Analyzer State : Enabled Cc Error : Disabled
PAT Rep Err : Enabled TNC PAT Rep : 200
QOS PAT Rep : 400 POA PAT Rep : 600
PAT Syntax : Enabled PCR Rep Err : Enabled
TNC PCR Rep : 200 QOS PCR Rep : 400
POA PCR Rep : 600 Vid PID Absent : 1000
PID PMT Unref : Enabled PMT Rep Err Secs : Enabled
TNC PMT Rep : 400 QOS PMT Rep : 800
POA PMT Rep : 2000 PMT Syntax : Enabled
SCTE35 Err Secs : Disabled TEI Err Secs : Disabled
TS Sync Loss : Enabled Non-Vid Pid Abse*: 1000
Alarm Sev : tnc
-------------------------------------------------------------------------------
Number of channels : 3
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:SR-12/Dut-C#
*A:SR-12/Dut-C# show video channel pid
===============================================================================
Video Channel PID
===============================================================================
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 0 PID Type : pat
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 16 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 2 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 126336
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 32 PID Type : video
MPEG Stream Type : 27 Is PCR PID : Yes
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 1941664
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 33 PID Type : pmt
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 16 PID Bitrate : 0
===============================================================================
*A:SR-12/Dut-C#
*A:SR-12/Dut-C# show video channel pid interface "video-300" source 10.20.13.2 address 192.0.2.6
===============================================================================
Video Channel PID
===============================================================================
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 0 PID Type : pat
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 16 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 2 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 136864
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 32 PID Type : video
MPEG Stream Type : 27 Is PCR PID : Yes
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 1931136
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 33 PID Type : pmt
MPEG Stream Type : 0 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 16 PID Bitrate : 0
Service Id : 300 Interface Name : video-300
Group Address : 192.0.2.6 Source Address : 10.20.13.2
PID : 308 PID Type : audio
MPEG Stream Type : 4 Is PCR PID : No
Cc Err Secs : 0 TEI Err Secs : 0
Absent Err Secs : 0 PID Bitrate : 136864
Number of pids for this channel: 5
-------------------------------------------------------------------------------
Number of channels : 1
===============================================================================
*A:SR-12/Dut-C#
channel
Syntax
channel all [rt-client] [rt-server] [fcc-server] [ad-insert]
channel grp-address [source srcAddr] [rt-client] [rt-server] [fcc-server] [ad-insert]
Context
[Tree] (clear>video>statistics>id channel)
Full Context
clear video statistics id channel
Description
This command clears video statistics for a particular channel.
Parameters
- all
-
Clears statistics for all channels.
- rt-client
-
Clears all RET client related statistics.
- rt-server
-
Clears all RET server related statistics.
- fcc-server
-
Clears all FCC server related statistics.
- ad-insert
-
Clears all ad insert related statistics.
- grp-address
-
Clears statistics for the specified channel group address.
- source srcAddr
-
Clears statistics for the specified source address.
Platforms
7450 ESS, 7750 SR-1, 7750 SR-7/12/12e, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
charging-filter
charging-filter
Syntax
charging-filter {charging-filter-id | non-zero}
Context
[Tree] (show>app-assure>group>policy charging-filter)
Full Context
show application-assurance group policy charging-filter
Description
This command displays information about the charging filter.
Parameters
- charging-filter-id
-
Specifies the ID of an existing charging filter entry.
- non-zero
-
Specifies to show all non-zero count entries.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output example shows the charging filter information, and Show AA group policy charging filter output fields describes the fields.
show application-assurance group 1:0 policy charging-filter 1
Sample
Output===============================================================
Charging Filter Entry 1
===============================================================
Description : "Charging-filter entry for WhatsApp Video"
Admin State : in-service
Charging Group : "cgVideo100"
Hits : 0 flows
Match :
Application : eq "Whats App"
Flow Attribute : flow-attribute video confidence gte 100
===============================================================
Label |
Description |
---|---|
Charging Filter Entry |
The charging filter |
Description |
The description of the charging filter |
Admin State |
The administrative state of the filter |
Charging Group |
The charging group |
Hits |
The number of hits |
Application |
The matched application |
Flow Attribute |
The flow attribute used by the match criteria |
charging-group
charging-group
Syntax
charging-group
charging-group charging-group-name
Context
[Tree] (show>app-assure>group>policy charging-group)
Full Context
show application-assurance group policy charging-group
Description
This command displays application-assurance policy application information.
Parameters
- charging-group-name
-
Specifies the application name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
charging-group
Syntax
charging-group [charging-group-name] count [detail]
charging-group count top granularity [max-count max-count]
Context
[Tree] (show>app-assure>group>aa-sub charging-group)
Full Context
show application-assurance group aa-sub charging-group
Description
This command displays application-assurance group charging group information.
Parameters
- charging-group-name
-
Specifies an existing charging group.
- count
-
Displays the counters for the charging group.
- detail
-
Displays detailed information.
- top
-
Displays counters sorted by granularity.
- granularity
-
Specifies the granularity of the search.
- max-count
-
Specifies the maximum flows to display.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
charging-group
Syntax
charging-group [charging-group-name] count
Context
[Tree] (show>app-assure>group>aa-sub>um charging-group)
Full Context
show application-assurance group aa-sub usage-monitor charging-group
Description
This command displays usage monitor statistics for the charging group.
Parameters
- charging-group-name
-
Specifies the charging group name, up to 32 characters.
- count
-
Displays counters for the charging group.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
charging-group
Syntax
charging-group [charging-group-name] count [detail]
Context
[Tree] (tools>dump>app-assure>group>aa-sub charging-group)
Full Context
tools dump application-assurance group aa-sub charging-group
Description
This command displays per-subscriber per-charging-group statistics.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
chassis
chassis
Syntax
chassis [environment] [ccm] [power-supply] [chassis-id]
chassis class chassis-class
chassis detail [class chassis-class]
Context
[Tree] (show chassis)
Full Context
show chassis
Description
This command displays general status information about the chassis.
Parameters
- chassis-id
-
Specifies the ID of the chassis.
- chassis-class
-
Displays information related to the chassis of the specified class.
- environment
-
Displays environmental status information about the chassis.
- power-supply
-
Displays the status of the power supply in the chassis.
- detail
-
Displays detailed information for all chassis in the system.
- ccm
-
Displays chassis control module information for platforms that support CCMs.
Platforms
All
Output
See the following sections for sample outputs:
-
Sample Output: show chassis power-supply (showing 7750 SR-1)
-
Sample Output: show chassis (showing 7750 SR with Ethernet satellites configured)
A:PE-1# show chassis
===============================================================================
System Information
===============================================================================
Name : PE-1
Type : 7750 SR-12
Chassis Topology : Standalone
Location : (Not Specified)
Coordinates : (Not Specified)
CLLI code :
Number of slots : 12
Oper number of slots : 12
Num of faceplate ports/connectors : 97
Num of physical ports : 97
Critical LED state : Off
Major LED state : Off
Minor LED state : Off
Over Temperature state : OK
Base MAC address : 10:e8:78:b8:21:47
Admin chassis mode : d
Oper chassis mode : d
Fabric Speed : 10 Gig
FP Generations : FP3
System Profile : none
===============================================================================
Chassis Summary
===============================================================================
Chassis Role Status
-------------------------------------------------------------------------------
1 Standalone up
===============================================================================
A:PE-1#
Sample Output: show chassis environment
A:SR-12# show chassis environment
===============================================================================
Chassis 1 Detail
===============================================================================
Environment Information
Number of fan trays : 3
Number of fans : 6
Fan tray number : 1
Speed : 44 %
Status : up
Fan tray number : 2
Speed : 44 %
Status : up
Fan tray number : 3
Speed : 44 %
Status : up
===============================================================================
Sample Output: show chassis power-supply (showing 7750
SR-1)
A:ALA-4# show chassis power-supply
===============================================================================
Chassis 1 Detail
===============================================================================
Power Supply Information
Number of power supplies : 1
Power supply number : 1
Power supply type : dc multiple
Power supply model : pem
Status1 : present
Input voltage 1 : 53.81 Volts
Status2 : failed
Input voltage 2 : 0.00 Volts
===============================================================================
A:ALA-4#
Sample Output: show chassis ccm
A:7750-3# show chassis ccm
===============================================================================
Chassis Information
===============================================================================
Chassis Control Module (CCM) Information
CCM number : 1
Equipped : yes
Type : ccm-xp
Hardware Data
Part number : Sim Part#
CLEI code : Sim CLEI
Serial number : ccm-0
Manufacture date : 01012003
Manufacturing string : Sim MfgString ccm-0
Manufacturing deviations : Sim MfgDeviation ccm-0
Administrative state : up
Operational state : up
Temperature : 32C
Temperature threshold : 75C
Time of last boot : N/A
Current alarm state : alarm cleared
===============================================================================
A:7750-3>
Sample Output: show chassis (showing 7950 XRS)
*A:PE-1# show chassis
===============================================================================
System Information
===============================================================================
Name : PE-1
Type : 7950 XRS-20
Chassis Topology : Standalone
Location : (Not Specified)
Coordinates : (Not Specified)
CLLI code :
Number of slots : 24
Oper number of slots : 12
Num of faceplate ports/connectors : 314
Num of physical ports : 314
Critical LED state : Off
Major LED state : Off
Minor LED state : Amber
Over Temperature state : OK
Base MAC address : 24:af:4a:a3:ac:c5
FP Generations : FP3
System Profile : none
===============================================================================
Chassis Summary
===============================================================================
Chassis Role Status
-------------------------------------------------------------------------------
1 Standalone up
===============================================================================
*A:PE-1#
Sample Output: show chassis detail (showing 7950 XRS)
*A:PE-1# show chassis detail
===============================================================================
System Information
===============================================================================
Name : PE-1
Type : 7950 XRS-20
Chassis Topology : Standalone
Location : (Not Specified)
Coordinates : (Not Specified)
CLLI code :
Number of slots : 24
Oper number of slots : 12
Num of faceplate ports/connectors : 314
Num of physical ports : 314
Critical LED state : Off
Major LED state : Off
Minor LED state : Amber
Over Temperature state : OK
Base MAC address : 24:af:4a:a3:ac:c5
FP Generations : FP3
System Profile : none
===============================================================================
Chassis 1 Detail
===============================================================================
Chassis Status : up
Chassis Role : Standalone
Hardware Data
Part number :
CLEI code :
Serial number : AME4-14
Manufacture date :
Manufacturing deviations : (Not Specified)
Manufacturing assembly number :
Time of last boot : 2017/10/23 12:29:41
Current alarm state : alarm active
-------------------------------------------------------------------------------
Environment Information
Number of fan trays : 2
Number of fans : 16
Fan tray number : 1
Speed : 38 %
Status : up
Hardware Data
Part number : 3HE07119AARB01
CLEI code : IPUCA9U1AA
Serial number : NS131062838
Manufacture date : 03212013
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0354-03
Administrative state : up
Operational state : up
Time of last boot : 2017/10/23 12:27:47
Current alarm state : alarm cleared
Firmware revision status : acceptable
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 53.00 Volts (10/23/2017 12:30:28)
Current : 53.00 Volts
Peak : 54.00 Volts (10/23/2017 12:29:48)
Wattage
Minimum : 106.00 Watts (10/23/2017 12:30:28)
Current : 159.00 Watts
Peak : 324.00 Watts (10/23/2017 12:29:48)
Max Required : 900.00 Watts
Amperage
Minimum : 2.00 Amps (10/23/2017 12:29:56)
Current : 3.00 Amps
Peak : 6.00 Amps (10/23/2017 12:29:48)
Fan tray number : 2
Speed : 38 %
Status : up
Hardware Data
Part number : 3HE07119AARB01
CLEI code : IPUCA9U1AA
Serial number : NS152062365
Manufacture date : 05232015
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0354-03
Administrative state : up
Operational state : up
Time of last boot : 2017/10/23 12:27:25
Current alarm state : alarm cleared
Firmware revision status : acceptable
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 52.00 Volts (10/23/2017 12:32:01)
Current : 52.00 Volts
Peak : 54.00 Volts (10/23/2017 12:29:54)
Wattage
Minimum : 106.00 Watts (10/23/2017 12:30:05)
Current : 156.00 Watts
Peak : 371.00 Watts (10/23/2017 12:29:51)
Max Required : 900.00 Watts
Amperage
Minimum : 2.00 Amps (10/23/2017 12:29:54)
Current : 3.00 Amps
Peak : 7.00 Amps (10/23/2017 12:29:51)
-------------------------------------------------------------------------------
Power Management Information
Power Management Mode : basic
Power Safety Level : 100%
Power Safety Alert : 0 watts
Number of PEQs : 12
PEQ number : 1
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0116
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:33
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 2
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1249G0022
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:26
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 3
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0141
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:31
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 4
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1249G0201
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:26
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 5
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0123
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:32
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 6
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0061
Manufacture date : 12182012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:34
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 7
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARB01
CLEI code : IPUPAJHUAA
Serial number : NS13226A310
Manufacture date : 06042013
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0532-02
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:33
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 8
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0152
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:29
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 9
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0122
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:28
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 10
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0146
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:25
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 11
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1249G0202
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:30
Current alarm state : alarm active
Firmware revision status : acceptable
PEQ number : 12
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Power-Zone : 1
Status : up
Input Feed Status : input B down
Input Power Mode : N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0115
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2017/10/23 12:27:29
Current alarm state : alarm active
Firmware revision status : acceptable
-------------------------------------------------------------------------------
Chassis Control Module (CCM) Information
CCM Slot : A
Equipped : yes
Hardware Data
Part number : 82-0263-03
CLEI code :
Serial number : AQUA03-30
Manufacture date :
Manufacturing deviations : (Not Specified)
Manufacturing assembly number :
Administrative state : up
Operational state : up
Temperature : 45C
Temperature threshold : 75C
Time of last boot : N/A
Current alarm state : alarm cleared
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 51.67 Volts (10/23/2017 12:31:59)
Current : 51.67 Volts
Peak : 52.68 Volts (10/23/2017 12:29:52)
Wattage
Minimum : 21.29 Watts (10/23/2017 12:30:20)
Current : 21.98 Watts
Peak : 22.66 Watts (10/23/2017 12:29:50)
Max Required : 22.00 Watts
Amperage
Minimum : 0.41 Amps (10/23/2017 12:30:20)
Current : 0.43 Amps
Peak : 0.43 Amps (10/23/2017 12:29:50)
CCM Slot : B
Equipped : yes
Hardware Data
Part number : 82-0263-03
CLEI code :
Serial number : AQUA03-10
Manufacture date :
Manufacturing deviations : (Not Specified)
Manufacturing assembly number :
Administrative state : up
Operational state : up
Temperature : 44C
Temperature threshold : 75C
Time of last boot : N/A
Current alarm state : alarm cleared
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 51.63 Volts (10/23/2017 12:32:00)
Current : 51.63 Volts
Peak : 52.59 Volts (10/23/2017 12:30:14)
Wattage
Minimum : 22.66 Watts (10/23/2017 12:30:40)
Current : 23.35 Watts
Peak : 23.35 Watts (10/23/2017 12:30:14)
Max Required : 22.00 Watts
Amperage
Minimum : 0.45 Amps (10/23/2017 12:30:14)
Current : 0.46 Amps
Peak : 0.46 Amps (10/23/2017 12:31:32)
===============================================================================
*A:PE-1#
Sample Output: show chassis (showing 7750 SR with Ethernet
satellites configured)
*A:PE-1# show chassis
===============================================================================
System Information
===============================================================================
Name : PE-1
Type : 7750 SR-12
Chassis Topology : Standalone
Location : (Not Specified)
Coordinates : (Not Specified)
CLLI code :
Number of slots : 12
Oper number of slots : 12
Num of faceplate ports/connectors : 165
Num of physical ports : 165
Critical LED state : Off
Major LED state : Off
Minor LED state : Off
Over Temperature state : OK
Base MAC address : 10:e8:78:b8:21:47
Admin chassis mode : d
Oper chassis mode : d
Fabric Speed : 10 Gig
FP Generations : FP3
System Profile : none
===============================================================================
Chassis Summary
===============================================================================
Chassis Role Status
-------------------------------------------------------------------------------
1 Standalone up
esat-1 Ethernet Satellite up
===============================================================================
*A:PE-1#
Output Fields: show chassis
Output Fields: show chassis describes the output fields for the show chassis command.
Label |
Description |
---|---|
Name |
The system name for the router. |
Type |
Displays the router model number. |
Chassis Topology |
Indicates the inter-chassis topology mode in which the system is operating. Standalone indicates that the system is comprised of a single physical router chassis. Extended (XRS-40) on a 7950 XRS based system indicates that two router chassis are connected together in a "back-to-back” topology with no additional switch fabric chassis. An extended chassis topology is comprised of two XRS-20 chassis and is also known as an XRS-40 system. |
Chassis role |
Specifies the Chassis Roles. Standalone — Specifies the value for all non-7950 XRS SR OS systems and for 7950 XRS-20 standalone systems. 7950 XRS-40 Master 7950 XRS-40 Extension |
Location |
The system location for the device. |
Coordinates |
A user-configurable string that indicates the Global Positioning System (GPS) coordinates for the location of the chassis. For example:
|
CLLI Code |
The Common Language Location Identifier (CLLI) that uniquely identifies the geographic location of places and certain functional categories of equipment unique to the telecommunications industry. |
Number of slots |
The number of slots in the 7450 ESS and 7750 SR chassis that are available for plug-in cards. The total number includes the IOM/CCM slot(s) and the CPM slots. |
Number of ports |
The total number of ports currently installed in this chassis. This count does not include the Ethernet ports on the CPMs/CCMs that are used for management access. |
Oper Number of Slots |
The number of slots in the 7950 XRS chassis that are available for XCM cards and CPM cards operating as the active or standby CPM. Oper Number of Slots goes to 24 when Chassis Topology is Extended. |
Critical LED state |
The current state of the Critical LED in this chassis. |
Major LED state |
The current state of the Major LED in this chassis. |
Minor LED state |
The current state of the Minor LED in this chassis. |
Base MAC address |
The base chassis Ethernet MAC address. |
FP Generations |
Identifies the FP generations for cards in the system. |
System Profile |
The scaling profile in use by the system. |
Over Temperature state |
Indicates if there is currently an over temperature condition (OK = not currently over temp). |
Admin chassis mode |
The configured chassis mode (chassis mode D). |
Oper chassis mode |
The current chassis mode. |
Part number |
The part number of the particular hardware assembly. In the show chassis output, the first set of Hardware Data output is for the chassis mid-plane. |
CLEI code |
The Common Language Equipment Code of the particular hardware assembly. |
Serial number |
The serial number of the particular hardware assembly. |
Manufacture date |
The manufacture date of the particular hardware assembly. |
Manufacturing string |
The factory inputted manufacturing text string for the particular hardware assembly. |
Manufacturing deviations |
Additional manufacturing data. |
Manufacturing assembly number |
Additional manufacturing data. |
Time of last boot |
The date and time the most recent boot occurred. |
Current alarm state |
Displays the alarm conditions for the specific board. |
Number of fan trays |
The total number of fan trays installed in this chassis. |
Number of fans |
The total number of fans installed in this chassis. |
Fan tray number |
The ID for each fan tray installed in the chassis |
Fan tray type |
Indicates the type of fan tray: Chassis - standard fan tray PCM - dedicated to cooling PCMs in the 7950 XRS-20e Universal chassis |
Operational status |
Current status of the fan tray. |
Speed |
Indicates the speed of the fans as a percentage. |
Status |
Current status of the particular hardware assembly (up, down, or not equipped). |
Number of power supplies |
The number of power supplies installed in the chassis. |
Power supply number |
The ID for each power supply installed in the chassis. |
Power supply type |
The basic type of the power supply. |
Power supply model |
The model of the power supply. |
Input voltage |
The input voltage for the specific power supply or power module. This field is only displayed for a subset of platforms. |
CCM Slot |
The identifier of the CCM (A or B). |
Equipped |
Indicates if the CCM is detected as physically present. |
Temperature |
The current temperature detected by the particular hardware assembly. |
Temperature threshold |
The temperature at which the particular hardware assembly considers an over temperature condition to exist. |
Part number |
The CCM part number. |
CLEI code |
The code used to identify the router. |
Serial number |
The CCM serial number. Not user modifiable. |
Manufacture date |
The chassis manufacture date. Not user modifiable. |
Manufacturing string |
Factory-inputted manufacturing text string. Not user modifiable. |
Administrative state |
Up — The card is administratively up. Down — The card is administratively down. |
Operational state |
Up — The card is operationally up. Down — The card is operationally down. |
Temperature |
The internal chassis temperature. |
Temperature threshold |
The value above which the internal temperature must rise in order to indicate that the temperature is critical. |
Time of last boot |
The date and time the most recent boot occurred. |
Current alarm state |
Displays the alarm conditions for the CCM. |
chassis
Syntax
chassis [phys-chassis-id]
Context
[Tree] (tools>perform chassis)
Full Context
tools perform chassis
Description
The following command performs chassis maintenance operations.
Parameters
- phys-chassis-id
-
The identifier of the physical chassis for the tools perform context.
Platforms
All
chassis
Syntax
chassis
Context
[Tree] (clear chassis)
Full Context
clear chassis
Description
Commands in this context clear data for various pieces of equipment that sit in a chassis.
Platforms
7750 SR-s
chassis
Syntax
chassis
Context
[Tree] (show>mcast-mgmt chassis)
Full Context
show mcast-management chassis
Description
This command displays multicast path management chassis information.
Platforms
7450 ESS, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-7/12/12e, 7750 SR-s, 7950 XRS, VSR
check-bp-eprom
check-bp-eprom
Syntax
check-bp-eprom
Context
[Tree] (tools>perform>chassis check-bp-eprom)
Full Context
tools perform chassis check-bp-eprom
Description
This command checks the chassis BP EPROM. The function reads the EPROM and is corrected with one of the following:
-
for each SEEP that is found to be acceptable or can be corrected:
"BP eprom X: ok” with X = seep number
-
for each SEEP that is found to be unacceptable and cannot be corrected:
"BP eprom X: not ok”
Platforms
All
cisco-hdlc
cisco-hdlc
Syntax
cisco-hdlc
Context
[Tree] (show>port cisco-hdlc)
Full Context
show port cisco-hdlc
Description
This command displays Cisco HDLC port information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
class-forwarding-policy
class-forwarding-policy
Syntax
class-forwarding-policy [policy-name]
Context
[Tree] (show>router>mpls class-forwarding-policy)
Full Context
show router mpls class-forwarding-policy
Description
This command displays the mapping of the Forwarding Classes (FCs) to the set IDs as well as the default set ID of the CBF policy. It also shows the number of MPLS LSPs that reference this CBF policy.
Parameters
- policy-name
-
Specifies the name of the class-forwarding-policy, up to 256 characters and composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
Output
The following is an example of class forwarding policy information.
Sample Output*A:Dut-B>show>router# show router mpls class-forwarding-policy "policy1"
==============================================================================
MPLS Class Forwarding Policy Table
==============================================================================
Policy Name Default Forwarding Class Set-id Ref
Set-Id be l2 af l1 h2 ef h1 nc Count
------------------------------------------------------------------------------
policy1 3 1 1 2 2 3 3 4 4 50
------------------------------------------------------------------------------
No. of Forwarding Policies: 1
==============================================================================
classic-lsn-sub
classic-lsn-sub
Syntax
classic-lsn-sub router-instance ip-prefix ip-prefix/length
classic-lsn-sub router-instance ip-prefix ip-prefix/length subscriber-string
Context
[Tree] (clear>nat classic-lsn-sub)
Full Context
clear nat classic-lsn-sub
Description
This command clears NAT mappings for classic LSN subscribers.
Parameters
- router-instance
-
Specifies the router instance, up to 32 characters.
- ip-prefix/length
-
Specifies the IP prefix and length.
- subscriber-string
-
Clears subscriber string information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
clear
clear
Syntax
clear aps-id {protect | working} [number number]
Context
[Tree] (tools>perform>aps clear)
Full Context
tools perform aps clear
Description
This command removes all Automated Protection Switching (APS) operational commands.
Parameters
- aps-id
-
This option clears a specific APS on un-bundled SONET/SDH ports.
- protect
-
This command clears a physical port that is acting as the protection circuit for the APS group.
- working
-
This command clears a physical port that is acting as the working circuit for this APS group.
- number
-
Specifies the APS channel number.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
clear
Syntax
clear ring-index
Context
[Tree] (tools>perform>eth-ring clear)
Full Context
tools perform eth-ring clear
Description
The clear command, at the Ethernet Ring Node, is used for the following operations:
-
Clearing an active local administrative command, such as a Forced Switch or Manual Switch
-
Triggering reversion before the WTR or WTB timer expires in case of revertive operation
-
Triggering reversion in case of non-reactive operation
Parameters
- ring-index
-
Specifies an Ethernet Ring index.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
clear
Syntax
clear id tunnel-id
clear lsp-name
Context
[Tree] (tools>perform>router>mpls>tp-tunnel clear)
Full Context
tools perform router mpls tp-tunnel clear
Description
This command clears all the MPLS-TP linear protection operational commands for the specified LSP that are currently active.
Parameters
- tunnel-id
-
Specifies the tunnel number of the MPLS-TP LSP.
- lsp-name
-
Specifies the name of the MPLS-TP LSP, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
clear-arp
clear-arp
Syntax
clear-arp [ip ipv4-address]
Context
[Tree] (tools>perform>wlan-gw>lanext>bd clear-arp)
Full Context
tools perform wlan-gw lanext bd clear-arp
Description
This command clears all ARP table entries for the specified HLE BD or a specific entry if an IPv4 address is specified.
Parameters
- ipv4-address
-
Specifies the IPv4 address of the ARP table entry to be cleared.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
clear-force
clear-force
Syntax
clear-force all-mc
clear-force lag-id lag-id [sub-group sub-group-id]
clear-force peer-mc ip-address
Context
[Tree] (tools>perform>lag clear-force)
Full Context
tools perform lag clear-force
Description
This command clears forced status.
Parameters
- all-mc
-
Specifies all MC-LAGs.
- lag-id
-
Specifies the LAG ID.
- sub-group-id
-
Specifies the subscriber group ID.
- ip-address
-
Specifies the peer MC IP address.
Platforms
All
clear-lockout-annexb
clear-lockout-annexb
Syntax
clear-lockout-annexb aps-id
Context
[Tree] (tools>perform>aps clear-lockout-annexb)
Full Context
tools perform aps clear-lockout-annexb
Description
This command clears lockout of the Annex B APS group.
Parameters
- aps-id
-
Specifies an APS ID.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
clear-mac
clear-mac
Syntax
clear-mac [mac ieee-address]
Context
[Tree] (tools>perform>wlan-gw>lanext>bd clear-mac)
Full Context
tools perform wlan-gw lanext bd clear-mac
Description
This command clears all MAC table entries for the specified HLE BD or a specific entry if a MAC address is specified.
Parameters
- ieee-address
-
Specifies the MAC address of the MAC table entry to be cleared.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
clear-neighbor
clear-neighbor
Syntax
clear-neighbor [ip6 ipv6-address]
Context
[Tree] (tools>perform>wlan-gw>lanext>bd clear-neighbor)
Full Context
tools perform wlan-gw lanext bd clear-neighbor
Description
This command clears all neighbor table entries for the specified HLE BD or a specific entry if an IPv6 address is specified.
Parameters
- ipv6-address
-
Specifies the IPv6 address of the neighbor table entry to be cleared.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
cli
cli
Syntax
cli
Context
[Tree] (show>log cli)
Full Context
show log cli
Description
Commands in this context display log information specific to CLI users (classic CLI or MD-CLI).
Platforms
All
cli-session-group
cli-session-group
Syntax
cli-session-group session-group-name
Context
[Tree] (show>system>security cli-session-group)
Full Context
show system security cli-session-group
Description
This command displays the user profiles of this CLI session group and the session group details.
Parameters
- session-group-name
-
Specifies a session group, up to 32 characters.
Platforms
All
client
client
Syntax
client all
client client-address ip-address
Context
[Tree] (show>test-oam>twamp client)
Full Context
show test-oam twamp client
Description
This command displays TWAMP client information.
Parameters
- ip-address
-
Specifies the IPv4 or IPv6 address of a client.
- all
-
Displays all TWAMP client information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following sample output shows TWAMP client information.
Sample Outputshow test-oam twamp client all
===============================================================================
Test Session information for Client 6.6.6.6
===============================================================================
Index : 1 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
Index : 2 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Number of Sessions: 2
===============================================================================
===============================================================================
Test Session information for Client 10.10.10.10
===============================================================================
Index : 1 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
Index : 2 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Index : 3 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Number of Sessions: 3
===============================================================================
Test Session information for Client 1234:5678:90ab:cdef:1234:5678:90ab:cdef
===============================================================================
Index : 1 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
Number of Sessions: 1
===============================================================================
show test-oam twamp client 6.6.6.6
===============================================================================
Test Session information for Client 6.6.6.6
===============================================================================
Index : 1 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
Index : 2 State : Active
SID : 16 byte hex field
Src Address : SourceIP Src UDP Port : port
Dst Address : DestIP Dst UDP Port : port
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Number of Sessions: 2
===============================================================================
client-db
client-db
Syntax
client-db
client-db db-name association
client-db db-name client client-index
client-db db-name
Context
[Tree] (show>ipsec client-db)
Full Context
show ipsec client-db
Description
This commands displays information for client databases. Using this command without any parameters will list all configured client database.
Parameters
- db-name
-
Species to list all IPsec gateways that use the specified client database.
- association
-
Displays information for which this client database is associated.
- client client-index
-
Specifies the client index or client name of client entry in the client database.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example output of the show client-db command.
Sample Outputshow ipsec client-db
===============================================================================
IPsec Client Database
===============================================================================
Name Admin State Match List
-------------------------------------------------------------------------------
test Up idi peer-ip-prefix
-------------------------------------------------------------------------------
No. of entries: 1
===============================================================================
show ipsec client-db "test"
===============================================================================
IPsec Client Database "test"
===============================================================================
Description: (Not Specified)
Match List : idi peer-ip-prefix
Admin State: Up
-------------------------------------------------------------------------------
Database Client List
-------------------------------------------------------------------------------
Index Name Admin State
-------------------------------------------------------------------------------
1 client-1 Up
2 client-2 Up
-------------------------------------------------------------------------------
No. of entries: 2
-------------------------------------------------------------------------------
===============================================================================
client-db
Syntax
client-db db-name lookup peer-ip peer-ip-address
client-db db-name lookup idi string-type {fqdn | rfc822} string-value string-value [peer-ip peer-ip-address]
client-db db-name lookup idi address idi-ip-address [peer-ip peer-ip-address]
Context
[Tree] (tools>perform>ipsec client-db)
Full Context
tools perform ipsec client-db
Description
This command performs a lookup in the specified client-db by using specified input and displays the matching result.
Sample Output
tools perform ipsec client-db "test" lookup idi string-type rfc822 string-
value client-1@examplebm.com peer-ip 10.10.10.100
Result : Ok
Database : test
Criterion - Ike Idi : RFC822 "client-1@examplebm.com"
Criterion - Peer IP : 10.10.10.100
Matched Record : 1 "client-1"
Elapsed Time (us) : 2
Parameters
- db-name
-
Specifies the name of the client-db.
- peer-ip peer-ip-address
-
Specifies the peer’s tunnel IP address as input, either v4 or v6.
- string-type
-
Specifies the peer’s IDi as input.
- idi-ip-address
-
Specifies the peer’s IDi of address type as input, either v4 or v6
- string-value string-value
-
Specifies the value of FQDN or RFC822 IDi.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
client-tls-profile
client-tls-profile
Syntax
client-tls-profile [client-tls-profile]
client-tls-profile client-tls-profile association
Context
[Tree] (show>system>security>tls client-tls-profile)
Full Context
show system security tls client-tls-profile
Description
This command displays TLS client profile information
Parameters
- client-tls-profile
-
Specifies the client TLS profile, up to 32 characters.
Platforms
All
Output
The following output is an example of TLS client profile information.
Sample Output*A:Dut-C> show system security tls client-tls-profile
===============================================================================
Client Profile Information
===============================================================================
Name AdminState OperState
-------------------------------------------------------------------------------
ctp up up
ctp-alt1 up up
ctp-alt2 up up
===============================================================================
*A:Dut-C> show system security tls client-tls-profile "ctp"
===============================================================================
Client Profile Entry "ctp"
===============================================================================
Cipher List Name : cl_all
Trust Anchor Profile Name : tap
===============================================================================
coa
coa
Syntax
coa [nas-port-id attr-string] [framed-ip-addr ip-address] [alc-ipv6-addr ipv6-address] [delegated-ipv6-pfx ipv6-prefix[/ipv6-prefix-length]] [framed-ipv6-pfx ipv6-prefix [/ipv6-prefix-length]] [alc-serv-id serv-id] [acct-session-id attr-string] [alc-subscr-id attr-string] [alc-brg-id attr-string] [user-name attr-string] [alc-client-hw-addr mac-address] [attr attribute [attribute]] [attr-from-file file-url] [from-server attr-string] [router-or-service attr-string] [debug]
Context
[Tree] (tools>perform>subscr-mgmt coa)
Full Context
tools perform subscriber-mgmt coa
Description
This command triggers a Change of Authorization (CoA) without a RADIUS authentication policy.
This command can be used to spoof a CoA from a configured server for purposes such as testing CoA python scripts. However, spoofing a CoA from a RADIUS server requires the configuration of a RADIUS authentication policy.
Parameters
- nas-port-id attr-string
-
Specifies the physical access circuit of the NAS up to 253 characters.
- ip-address
-
Specifies the IPv4 host address.
- ipv6-address
-
Specifies the IPv6 host address.
- ipv6-prefix[/ipv6-prefix-length]
-
Specifies the IPv6 PD host prefix.
- ipv6-prefix[/ipv6-prefix-length]
-
Specifies the IPv6 SLAAC host prefix.
- serv-id
-
Specifies the service ID of the LNS subscriber.
- acct-session-id attr-string
-
Specifies the subscriber accounting session ID up to 22 characters.
- alc-subscr-id attr-string
-
Specifies the subscriber ID up to 32 characters.
- alc-brg-id attr-string
-
Specifies the BRG ID to a maximum of 32 characters.
- user-name attr-string
-
Specifies the string matching RADIUS VSA [1] username associated to the host(s), up to 32 characters.
- mac-address
-
Specifies the subscriber host MAC address in the form: xx:xx:xx:xx:xx:xx.
- attribute
-
Specifies the attributes (RADIUS VSAs) for override. The VSA must be specified in number format. For example, VSA Alc-Subsc-Prof-Str=”1M-prof” is expressed as 6527.12 ="1M-prof”. Up to five attributes can be specified within this command.
For more information on VSAs, refer to the 7750 SR and VSR RADIUS Attributes Reference Guide.
- file-url
-
Specifies the file URL where the VSAs are located.
- attr-string
-
Specifies the RADIUS server name that is configured under the router or VPRN service context, up to 32 characters.
- attr-string
-
Specifies the router or VPRN service instance where the RADIUS server is configured, up to 32 characters.
- debug
-
Displays the debug message associated with the CoA command.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example of subscriber management CoA tools information.
Sample OutputNode# tools perform subscriber-mgmt coa alc-subscr-id subscriber-01 attr 6527,13=new-sla-prof debug
===============================================================================
Inject Change-of-Authorization
===============================================================================
SUCCESS: got ACK
Change of Authorization(43) id 0 len 50 from 0.0.0.0:3799 vrid 1
VSA [26] 8 Nokia (6527)
SUBSC ID STR [11] 6 subscriber-01
VSA [26] 10 Nokia (6527)
SLA PROF STR [13] 8 new-sla-prof
Hex Packet Dump:
1a 0e 00 00 19 7f 0b 08 77 69 66 69 2d 31 1a 10 00 00 19 7f 0d 0a 73 6c 61
2d 70 72 6f 66
Change of Authorization Ack(44) 0.0.0.0:3799 id 0 len 20 vrid 1
Hex Packet Dump:
coa-statistics
coa-statistics
Syntax
coa-statistics
Context
[Tree] (clear>subscr-mgmt>authentication coa-statistics)
Full Context
clear subscriber-mgmt authentication coa-statistics
Description
This command clears RADIUS CoA statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
collect-lmm-fc-stats
collect-lmm-fc-stats
Syntax
collect-lmm-fc-stats [{sap {sap-id | all} | sdp {sdp-id | all} | interface {interface-name | all}}]
Context
[Tree] (show>eth-cfm collect-lmm-fc-stats)
Full Context
show eth-cfm collect-lmm-fc-stats
Description
This command displays the entities that are configured with per-FC LMM counters, and whether those counters are counting in-profile packets only or all countable packets.
Each entity may have up to eight individual FC-based counters. Each FC includes a positional index value (1 to 8) under the FC that is counting. A "P” indicates that the index is only counting in-profile traffic.
When no display filters are applied, this command displays all entities and the individual FC counters. Optional filters help to reduce the output that is visible to the operator.
Parameters
- sap-id
-
Specifies a SAP entity for which to display active individual FC counters.
- sdp-id
-
Specifies an SDP entity for which to display active individual FC counters.
- interface-name
-
Specifies an interface entity for which to display active individual FC counters, up to 32 characters maximum.
- all
-
Keyword to display all SAP, SDP, and interface entities, and the associated active individual FC counters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following sample output shows information about entities that are configured with per-FC counters.
Sample Outputshow eth-cfm collect-lmm-fc-stats
===============================================================================
The FC to priority bit mapping for collect-lmm-fc-stats is as follows:
NC = 7, H1 = 6, EF = 5, H2 = 4, L1 = 3, AF = 2, L2 = 1, BE = 0
The number below each FC column indicates which counter index PDUs matching
that FC will be counted in. Entries with a "P" beside the number indicate
that only in-profile traffic is being counted. Entries without a "P" are not
profile aware and count all PDUs associated with that FC.
===============================================================================
ETH-CFM SAPs Configured to Collect Per-FC LMM Statistics
===============================================================================
Sap SvcId BE L2 AF L1 H2 EF H1 NC
-------------------------------------------------------------------------------
1/1/1:100 2147483647 1 2P 3 4 5 8P
-------------------------------------------------------------------------------
No. of SAPs: 1
===============================================================================
===============================================================================
ETH-CFM SDPs Configured to Collect Per-FC LMM Statistics
===============================================================================
SdpId SvcId BE L2 AF L1 H2 EF H1 NC
-------------------------------------------------------------------------------
500:500 2147483647 1 2 4P 5P 6
-------------------------------------------------------------------------------
No. of SDPs: 1
===============================================================================
===============================================================================
ETH-CFM Facility Interface MEPs Configured to Collect Per-FC LMM Statistics
===============================================================================
Interface Md-index Ma-index MepId BE L2 AF L1 H2 EF H1 NC
-------------------------------------------------------------------------------
system 1 1 1 1 2 3 4 5P 6P 7P
-------------------------------------------------------------------------------
No. of Facility Interface MEPs: 1
===============================================================================
collect-lmm-stats
collect-lmm-stats
Syntax
collect-lmm-stats
Context
[Tree] (show>eth-cfm collect-lmm-stats)
Full Context
show eth-cfm collect-lmm-stats
Description
This command displays the entities that are configured with a single LMM counter using the format of the ETH-CFM stack table.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of LMM counter information.
Sample Outputshow eth-cfm collect-lmm-stats
=========================================================
ETH-CFM SAPs Configured to Collect LMM Statistics
=========================================================
SapId SvcId
---------------------------------------------------------
1/2/1:1000.1000 1000
---------------------------------------------------------
No. of SAPs: 1
=========================================================
===============================================================================
ETH-CFM SDPs Configured to Collect LMM Statistics
===============================================================================
SdpId SvcId Type Far End
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of SDPs: 0
===============================================================================
===============================================================================
CFM Stack Table Defect Legend:
R = Rdi, M = MacStatus, C = RemoteCCM, E = ErrorCCM, X = XconCCM
A = AisRx, L = CSF LOS Rx, F = CSF AIS/FDI rx, r = CSF RDI rx
G = receiving grace PDU (MCC-ED or VSM) from at least one peer
===============================================================================
CFM Facility Port Stack Table
===============================================================================
Port Tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
1/1/1 0 0 D 10 1 28 d8:1c:01:01:00:01 ------- -
===============================================================================
===============================================================================
CFM Facility LAG Stack Table
===============================================================================
Lag Tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
CFM Facility Tunnel Stack Table
===============================================================================
Port/Lag Tunnel Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
CFM Facility Interface Stack Table
===============================================================================
Interface Lvl Dir Md-index Ma-index MepId Mac-address Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
collect-lmm-stats
Syntax
collect-lmm-stats [sdp-id[:vc-id]]
Context
[Tree] (show>service>sdp-using>eth-cfm collect-lmm-stats)
Full Context
show service sdp-using eth-cfm collect-lmm-stats
Description
This command displays SDP bindings which are configured to collect statistics for LMM tests.
Parameters
- sdp-id[:vc-id]
-
Specifies the SDP ID and virtual circuit ID on the SDP ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
collector
collector
Syntax
collector [detail]
Context
[Tree] (show>app-assure>group>cflowd collector)
Full Context
show application-assurance group cflowd collector
Description
Commands in this context display cflowd output.
Parameters
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example show output for the collector command.
Sample OutputA:ALU-A# show application-assurance group 1 cflowd collector
========================================================================
Application Assurance Cflowd Collectors for group 1
========================================================================
Host Address Port Version Admin Oper Recs Sent
------------------------------------------------------------------------
192.168.7.7 2055 10 up up 0
192.168.7.8 2055 10 up up 0
------------------------------------------------------------------------
Collectors : 2
------------------------------------------------------------------------
A:ALU-A#
A:ALU-A# show application-assurance group 1 cflowd collector detail
========================================================================
Application Assurance Cflowd Collectors for group 1
========================================================================
Address : 192.168.7.7
Port : 2055
Description : AA Collector 1
Version : 10
Admin State : up
Oper State : up
Records Sent : 0
Last Changed : 07/27/2009 13:36:50
Address : 192.168.7.8
Port : 2055
Description : AA Collector 2
Version : 10
Admin State : up
Oper State : up
Records Sent : 0
Last Changed : 07/27/2009 13:37:10
========================================================================
A:ALU-A#
collector
Syntax
collector collector-id
Context
[Tree] (show>app-assure>group>cflowd>dir-exp collector)
Full Context
show application-assurance group cflowd direct-export collector
Description
Commands in this context display cflowd direct-export collector output.
Parameters
- collector-id
-
Specifies the ID of the cflowd direct export collector.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following is an example show output for the collector command.
Sample OutputA:Sim# show application-assurance group 1 cflowd direct-export collector 1
===============================================================================
Application Assurance Group 1 Cflowd Direct-Export Collector 1
===============================================================================
Collector Status : Inactive
VLAN Id : N/A
Cflowd Version : 10
Admin State : down
Description : (Not Specified)
-------------------------------------------------------------------------------
Host Address Port Admin Oper Records Sent
-------------------------------------------------------------------------------
192.168.2.1 4739 DOWN DOWN 0
192.168.2.2 4739 down down 0
-------------------------------------------------------------------------------
No. of Cflowd Direct Export Collector Addresses: 2
===============================================================================
Application Assurance Group 1 Cflowd Collectors
Collector Status : Active
===============================================================================
Address : 192.168.2.1
Port : 4739
Description :
Version : 10
Admin State : down
Oper State : down
Records Sent : 5400
Last Changed : 08/12/2015 19:12:28
Address : 192.168.2.2
Port : 4739
Description :
Version : 10
Admin State : down
Oper State : down
Records Sent : 5400
Last Changed : 08/12/2015 19:12:35
===============================================================================
status [isa <slot/mda>] cflowd
collector
Syntax
collector [ip-address[:port]] [detail]
Context
[Tree] (show>cflowd collector)
Full Context
show cflowd collector
Description
This command displays administrative and operational status of data collector configuration.
Parameters
- ip-address
-
Displays information only about the specified collector IP address.
- :port
-
Displays information only about the collector on the specified UDP port.
- detail
-
Displays details about either all collectors or the specified collector.
Platforms
All
Output
cflowd Collector Output —The following output is an example of cflowd Collector information, and Show cflowd Collector Output Fields describes the output fields.
A:R51-CfmA# show cflowd collector
===============================================================================
Cflowd Collectors
===============================================================================
Host Address Port Version AS Type Admin Oper Sent
-------------------------------------------------------------------------------
138.120.135.103 2055 v5 peer up up 1380 records
138.120.135.103 9555 v8 origin up up 90 records
138.120.135.103 9996 v9 - up up 0 packets
138.120.214.224 2055 v5 origin up up 1380 records
-------------------------------------------------------------------------------
Collectors : 4
===============================================================================
Label |
Description |
---|---|
Host Address |
The IP address of a remote cflowd collector host to receive the exported cflowd data |
Port |
The UDP port number on the remote cflowd collector host to receive the exported cflowd data |
AS Type |
The style of AS reporting used in the exported flow data |
origin — reflects the endpoints of the AS path which the flow is following |
|
peer — reflects the AS of the previous and next hops for the flow |
|
Version |
Specifies the configured version for the associated collector |
Admin |
The desired administrative state for this cflowd remote collector host |
Oper |
The current operational status of this cflowd remote collector host |
Recs Sent |
The number of cflowd records that have been transmitted to this remote collector host |
Collectors |
The total number of collectors using this IP address |
cflowd Collector Detail Output —The following output is an example of cflowd Collector information, and Show cflowd Collector Detailed Output Fields describes the output fields.
Sample Output
A:R51-CfmA# show cflowd collector detail
===============================================================================
Cflowd Collectors (detail)
===============================================================================
Address : 138.120.135.103
Port : 2055
Description : Test v5 Collector
Version : 5
AS Type : peer
Admin State : up
Oper State : up
Records Sent : 1260
Last Changed : 09/03/2009 17:24:04
Last Pkt Sent : 09/03/2009 18:07:10
-------------------------------------------------------------------------------
Sent Open Errors
-------------------------------------------------------------------------------
42 0 0
===============================================================================
Address : 138.120.135.103
Port : 9555
Description : Test v8 Collector
Version : 8
AS Type : origin
Admin State : up
Oper State : up
Records Sent : 82
Last Changed : 09/03/2009 17:24:04
Last Pkt Sent : 09/03/2009 18:06:41
-------------------------------------------------------------------------------
Aggregation Type Status Sent Open Errors
-------------------------------------------------------------------------------
as-matrix Disabled 0 0 0
protocol-port Disabled 0 0 0
source-prefix Enabled 21 0 0
destination-prefix Enabled 21 0 0
source-destination-prefix Disabled 0 0 0
raw Disabled 0 0 0
===============================================================================
Address : 138.120.135.103
Port : 9996
Description : Test v9 Collector
Version : 9
Admin State : up
Oper State : up
Packets Sent : 51
Last Changed : 09/03/2009 17:24:04
Last Pkt Sent : 09/03/2009 18:07:10
Template Set : Basic
-------------------------------------------------------------------------------
Traffic Type Template Sent Sent Open Errors
-------------------------------------------------------------------------------
IPv4 09/03/2009 18:07:29 51 1 0
MPLS No template sent 0 0 0
IPv6 No template sent 0 0 0
===============================================================================
A:R51-CfmA#
Label |
Description |
---|---|
Address |
The IP address of a remote cflowd collector host to receive the exported cflowd data |
Port |
The UDP port number on the remote cflowd collector host to receive the exported cflowd data |
Description |
A user-provided descriptive string for this cflowd remote collector host |
Version |
The version of the flow data sent to the collector |
AS Type |
The style of AS reporting used in the exported flow data |
origin — reflects the endpoints of the AS path which the flow is following |
|
peer — reflects the AS of the previous and next hops for the flow |
|
Admin State |
The desired administrative state for this cflowd remote collector host |
Oper State |
The current operational status of this cflowd remote collector host |
Records Sent |
The number of cflowd records that have been transmitted to this remote collector host |
Last Changed |
The time when this row entry was last changed |
Last Pkt Sent |
The time when the last cflowd packet was sent to this remote collector host |
Aggregation Type |
The bit mask which specifies the aggregation schemes used to aggregate multiple individual flows into an aggregated flow for export to this remote host collector |
none — no data will be exported for this remote collector host |
|
raw — flow data is exported without aggregation in version 5 format |
|
All other aggregation types use version 8 format to export the flow data to this remote host collector |
|
Collectors |
The total number of collectors using this IP address |
Sent |
The number of packets with flow date sent to the associated collector |
Open |
This counter shows the number of partially filled packets which have some flow data but are not yet filled or have been timed out (60 seconds maximum) |
Error |
This counter increments when there was an error during exporting of the collector packet; the most common reason will be a UDP unreachable destination for the configured collector |
command-list
command-list
Syntax
command-list
Context
[Tree] (tools>dump>service>vsd-services command-list)
Full Context
tools dump service vsd-services command-list
Description
This command displays the list of CLI nodes allowed in the VSD fully dynamic provisioning model. Python will have access to the shown nodes.
When access is granted to a node, all commands in that node are allowed; however, CLI nodes are only allowed if explicitly listed. Nodes in CLI are shown with a "+” in the CLI.
While you can navigate special "Pass through nodes” via these nodes, the commands in that node are not implicitly allowed. When configured in a service through VSD, these commands will not be shown in the 'info' output of the config command.
A 'node' implies leaf-nodes and leaf-table nodes in reality. A 'Leaf-table' is a sub-table that looks like a leaf (i.e. it is entered/displayed as a one-liner). An example of leaf-table node is /configure router policy-options prefix-list x prefix 0.0.0.0/0 - since you can have multiple instances of prefixes.
Platforms
All
commit-history
commit-history
Syntax
commit-history
commit-history [keyword] [commit-id number]
Context
[Tree] (show>system>management-interface commit-history)
Full Context
show system management-interface commit-history
Description
This command displays the history of configuration changes that were committed in model-driven interfaces. A separate history of the last commits is maintained for each configuration region (bof, configure, debug, and li). Each commit is uniquely identified by a numerical sequential incrementing commit ID assigned by the system.
This command is not available in the classic CLI.
Parameters
- keyword
-
Specifies the configuration region to display.
- number
-
Specifies the commit history ID to display.
Platforms
All
Output
The following is an example of commit history information.
The following table describes the commit history output fields.
Sample OutputA:admin@node-2# show system management-interface commit-history
===============================================================================
Commit History
===============================================================================
Total Commits : 4
4
Committed 2022-02-01T11:13:38.7-05:00 by admin (NETCONF) from 10.1.236.68
Comment "Fourth commit with NETCONF."
Location "cf3:\config.cfg"
3
Committed 2022-02-01T11:01:03.8-05:00 by admin (MD-CLI) from 10.1.145.205
Comment "Third commit with the MD-CLI."
Location "cf3:\config.cfg.1"
2
Committed 2022-02-01T11:00:47.7-05:00 by admin (MD-CLI) from 10.1.145.205
Comment "Second commit with the MD-CLI."
Location "cf3:\config.cfg.2"
1
Committed 2022-02-01T10:56:01.3-05:00 by system (MD-CLI) from Console
Log "System booted version B-22.2.R1."
Location "Configuration is not saved to startup."
Label |
Description |
---|---|
Commit ID |
Displays the commit ID. |
Committed |
Displays the date and time when the commit completed. |
By |
Displays the user and interface type that committed. |
From |
Displays the origin of the commit operation. |
Comment |
Displays the comment added by the user. |
Log |
Displays the log added by the system. |
Increment |
Displays the incremental saved configuration file location. |
Location |
Displays the complete saved configuration file location. |
community
community
Syntax
community community-string
Context
[Tree] (show>system>security>snmp community)
Full Context
show system security snmp community
Description
This command lists SNMP communities and characteristics. Including the community-name parameter modifies the output to include all details for the specified community, including the source IP address list and validation failure counters.
Platforms
All
Output
The following is an example of SNMP community information.
Show Community Output Fields describes the community output fields.
Sample OutputThe system-created communities that begin with "cli-” are only used for internal CLI management purposes and are not exposed to external SNMP access.
A:ALA-1# show system security snmp community
==============================================================================
Communities
==============================================================================
community access view version group name
------------------------------------------------------------------------------
cli-li-readwrite n/a li-view v2c cli-li-readwrite
cli-readonly r iso v2c cli-readonly
cli-readwrite rw iso v2c cli-readwrite
my-private1 rw iso v1 v2c snmp-rwa
my-public2 r no-security v1 v2c snmp-ro
test-123 rwa n/a v2c snmp-trap
------------------------------------------------------------------------------
No. of Communities: 6
==============================================================================
A:ALA-1#
A:ALA-1# show system security snmp community "my-public2"
==============================================================================
Communities
==============================================================================
community access view version group name
src-access-list authFailures
------------------------------------------------------------------------------
my-public2 r no-security v1 v2c snmp-ro
my-list1 5
==============================================================================
A:ALA-1#
Label |
Description |
---|---|
Community |
Displays the community string name for SNMPv1 and SNMPv2c access only. |
Access |
Displays access information. r — The community string allows read-only access. rw — The community string allows read-write access. rwa — The community string allows read-write access. mgmt — The unique SNMP community string assigned to the management router. vpls-mgmt — The unique SNMP community string assigned for vpls management. |
View |
Displays the view name. |
Version |
Displays the SNMP version. |
Group Name |
Displays the access group name. |
src-access-list |
Displays the name of the list of source IP addresses that are allowed to use the community, as configured using the community configuration command. |
authFailures |
Displays the number of SNMP requests that have failed validation using this community. |
No of Communities |
Displays the total number of configured community strings. |
community
Syntax
community comm-id {detail | longer}
community comm-id
community comm-id hunt
Context
[Tree] (show>router>bgp>routes community)
Full Context
show router bgp routes community
Description
This command displays BGP routes with routes with a community value matching the specified value.
community is a parameter of the show router bgp routes command. Depending on the parameters that are used to issue the command, the output can display a narrower or wider set of routes, including routes belonging to other address families. See the show router bgp routes command description for syntax variants, parameter descriptions and values, and output examples.
Parameters
- comm-id
-
Specifies the community ID, up to 72 characters.
- hunt
-
Displays entries for the specified route.
Platforms
All
completed
completed
Syntax
completed [script-policy-name] [owner owner-name]
Context
[Tree] (clear>system>script-control>script-policy completed)
Full Context
clear system script-control script-policy completed
Description
This command clears completed script run history entries.
Parameters
- script-policy-name
-
Specifies to only clear history entries for the specified script-policy. 32 characters maximum.
- owner-name
-
Specifies to only clear history entries for script-policies with the specified owner. 32 characters maximum.
Platforms
All
configuration-mode
configuration-mode
Syntax
configuration-mode {mixed | model-driven} check [li | configure]
Context
[Tree] (tools>perform>system>management-interface configuration-mode)
Full Context
tools perform system management-interface configuration-mode
Description
This command checks if the configuration meets the prerequisite reference requirements to change the management interface configuration mode. Incompatible configuration commands are displayed with an error reason if the prerequisite is not met. This command does not check if the configuration has commands that are unsupported in model-driven interfaces.
Parameters
- mixed
-
Specifies to check mixed management interface configuration mode.
- model-driven
-
Specifies to check model-driven management interface configuration mode.
- li
-
Specifies to only check the li configuration region.
- configure
-
Specifies to only check the configure configuration region.
Platforms
All
configuration-sessions
configuration-sessions
Syntax
configuration-sessions
Context
[Tree] (show>system>management-interface configuration-sessions)
Full Context
show system management-interface configuration-sessions
Description
This command displays configuration sessions information.
Platforms
All
Output
The following is an example of configuration session information. Configuration-sessions Output Fields describes the output fields.
Sample Output(pr)[]
A:admin@node-1# show system management-interface configuration-sessions
===============================================================================
Session ID Region Datastore Lock State
Username Session Mode Idle Time
Session Type From
-------------------------------------------------------------------------------
#65 configure Candidate Unlocked
admin Private 0d 00:00:00
MD-CLI 192.168.0.10
66 configure Candidate Unlocked
admin Private 0d 00:05:41
MD-CLI 192.168.0.10
67 configure Candidate Unlocked
admin Private 0d 00:05:08
MD-CLI 192.168.0.10
68 configure Candidate Unlocked
admin Read-Only 0d 00:02:25
MD-CLI (2) 192.168.0.10
69 configure Candidate, Running Locked
admin Exclusive 0d 00:01:54
MD-CLI 192.168.0.10
-------------------------------------------------------------------------------
Number of sessions: 5
'#' indicates the current active session
'(n)' indicates the number of internal sessions
===============================================================================
Label |
Description |
---|---|
Session ID |
The session ID. |
Region |
The region or scope that the datastore belongs to. |
Datastore |
Datastores that can be locked. For example: Running and Candidate. |
Lock State |
Locked — Indicates the session is in a locked state. Unlocked — Indicates the session is in an unlocked state. |
Username |
The name of the user. |
Session Mode |
Exclusive — An exclusive session. Global — A shared session. Private — A private session. Private Exclusive — A private exclusive session. Read-Only — A read-only session. |
Idle Time |
The idle time of the session. |
Session Type |
NETCONF — Indicates a NETCONF session is running. MD-CLI — Indicates an MD-CLI session is running. gRPC — Indicates a gRPC session is running. SNMP — Indicates an SNMP session is running. Classic CLI — Indicates a classic CLI session is running. System — Indicates a system session is running. |
From |
The originating IP address, CRON, or EHS. |
connection-profile
connection-profile
Syntax
connection-profile [1 to 8000]
Context
[Tree] (show connection-profile)
Full Context
show connection-profile
Description
This command displays connection profile information.
Parameters
- conn-prof-id
-
Specifies the connection profile ID.
Platforms
7450 ESS, 7750 SR-7/12/12e
Output
The following output is an example of connection profile information.
Sample Output*A:Dut-A# show connection-profile
========================================================================
Connection Profile Summary Information
========================================================================
CP Index Number of
Members
------------------------------------------------------------------------
10 2
20 2
========================================================================
*A:Dut-A#
*A:Dut-A# show connection-profile 10
========================================================================
Connection Profile 10 Information
========================================================================
Description : (Not Specified)
Last Change : 10/16/2010 06:53:30
------------------------------------------------------------------------
VPI/VCI
------------------------------------------------------------------------
10/11
10/12
========================================================================
*A:Dut-A#
*A:Dut-A#
*A:bksim2801# show connection-profile
========================================================================
Connection Profile Summary Information
========================================================================
CP Index Number of
Members
-------------------------------------------------------------------------------
5000 0
========================================================================
*A:bksim2801#
*A:bksim2801# show connection-profile 2
========================================================================
Connection Profile 2 Information
========================================================================
Description : (Not Specified)
Last Change : 09/09/2010 07:55:28
------------------------------------------------------------------------
VPI/VCI
------------------------------------------------------------------------
2/102
10/100
========================================================================
*A:bksim2801#
connection-profile-vlan
connection-profile-vlan
Syntax
connection-profile-vlan [conn-prof-id]
Context
[Tree] (show connection-profile-vlan)
Full Context
show connection-profile-vlan
Description
This command displays information about the connection-profiles (VLAN) in the system. When a specific connection profile is shown, the vlan-ranges that it contains are displayed.
Parameters
- conn-prof-id
-
Specifies the VLAN connection profile ID.
Platforms
All
Output
The following is an example of connection profile VLAN information.
Sample Output*A:Dut# show connection-profile-vlan
=======================================================================
Connection Profile Vlan Summary Information
=======================================================================
CP Index Number of Members
-----------------------------------------------------------------------
1 2
=======================================================================
*A:Dut# show connection-profile-vlan 1
=======================================================================
Connection Profile 1 Information
=======================================================================
Description : (Not Specified)
Last Change : 12/01/2015 16:50:34
=======================================================================
Connection Profile Vlan Eth Information
=======================================================================
Range Start Range End Last Change
-----------------------------------------------------------------------
5 100 12/01/2015 16:50:34
150 300 12/01/2015 16:50:34
=======================================================================
connections
connections
Syntax
connections
Context
[Tree] (show>li>x-interfaces connections)
Full Context
show li x-interfaces connections
Description
This command displays the connections between the X1, X2, and X3 interfaces.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
connections
Syntax
connections
Context
[Tree] (show>port>atm connections)
Full Context
show port atm connections
Description
This command displays ATM connection information.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e, 7950 XRS
connections
Syntax
connections
Context
[Tree] (show>ml-bundle>ima>atm connections)
Full Context
show multilink-bundle ima atm connections
Description
This command displays connection information.
Platforms
7450 ESS, 7750 SR-7/12/12e
Output
The following output is an example of IMA ATM connections information, and Output Fields: show multilink-bundle <bundle-id> ima atm connections describes the output fields.
Sample Output: show multilink-bundle bundle-ima ima atm connectionsA:NS052651098# show multilink-bundle bundle-ima-1/1.1 ima atm connections
================================================================
ATM Connections, Port bundle-ima-1/1.1
================================================================
Owner Type Ing.TD Egr.TD Adm OAM Opr
----------------------------------------------------------------
1/100 SAP PVC 2 2 up up up
================================================================
A:NS052651098#
Label |
Description |
---|---|
Owner |
Identifies the system entity that owns a specific ATM connection. |
Type |
Specifies the type of this multilink bundle. mlppp — Indicates that the bundle is of type MLPPP. ima — Indicates that the bundle is of type IMA group. |
Ing.TD |
Specifies the ATM traffic descriptor profile that applies to the receive direction of the interface connection. |
Egr.TD |
Specifies the ATM traffic descriptor profile that applies to the transmit direction of the interface connection. |
Adm |
ima — Indicates that the bundle is of type IMA group. Down — The bundle is administratively down. |
Opr |
Up — The bundle is operationally up. Down — The bundle is operationally down. |
OAM |
Indicates the OAM operational status of ATM connections. |
connections
Syntax
connections [detail] [address ip-address] [port port-number]
Context
[Tree] (show>system connections)
Full Context
show system connections
Description
This command displays UDP and TCP connection information.
If no command line options are specified, a summary of the TCP and UDP connections displays.
Parameters
- ip-address
-
Displays only the connection information for the specified IP address.
- port-number
-
Displays only the connection information for the specified port number.
- detail
-
Appends TCP statistics to the display output.
Platforms
All
Output
The following output is an example of system connections information, and System Connections Field Descriptions describes the output fields.
Sample OutputA:ALA-12# show system connections
===============================================================================
Connections
===============================================================================
Prot RecvQ TxmtQ Local Address State
MSS Remote Address vRtrID
-------------------------------------------------------------------------------
TCP 0 0 0.0.0.0.21 LISTEN
1024 0.0.0.0.0 0
TCP 0 0 0.0.0.0.22 LISTEN
1024 0.0.0.0.0 0
TCP 0 0 0.0.0.0.23 LISTEN
1024 0.0.0.0.0 0
TCP 0 0 0.0.0.0.830 LISTEN
1024 0.0.0.0.0 0
TCP 0 0 0.0.0.0.6068 LISTEN
1024 0.0.0.0.0 0
TCP 0 0 0.0.0.0.47806 LISTEN
1024 0.0.0.0.0 0
TCP 0 0 ::.21 LISTEN
1024 ::.0 0
TCP 0 0 ::.22 LISTEN
1024 ::.0 0
TCP 0 0 ::.830 LISTEN
1024 ::.0 0
TCP 0 0 ::.47806 LISTEN
1024 ::.0 0
TCP 0 0 192.168.0.11.21 LISTEN
1024 0.0.0.0.0 4095
TCP 0 0 192.168.0.11.21059 LISTEN
1024 0.0.0.0.0 4095
TCP 0 0 172.31.129.98.22 LISTEN
1024 0.0.0.0.0 4095
TCP 0 0 172.31.129.98.23 ESTABLISH
1024 192.168.140.149.59042 4095
TCP 0 1149 172.31.129.98.23 ESTABLISH
1024 192.168.140.244.58579 4095
TCP 0 0 172.31.129.98.830 LISTEN
1024 0.0.0.0.0 4095
TCP 0 0 2001:db8::8779:8163.22 LISTEN
1024 ::.0 4095
TCP 0 0 2001:db8::8779:8163.830 LISTEN
1024 ::.0 4095
UDP 0 0 0.0.0.0.67 ---
0.0.0.0.0 0
UDP 0 0 0.0.0.0.68 ---
0.0.0.0.0 0
UDP 0 0 0.0.0.0.123 ---
0.0.0.0.0 0
UDP 0 0 0.0.0.0.319 ---
0.0.0.0.0 0
UDP 0 0 0.0.0.0.320 ---
0.0.0.0.0 0
UDP 0 0 0.0.0.0.514 ---
0.0.0.0.0 0
UDP 0 0 0.0.0.0.50055 ---
0.0.0.0.0 0
UDP 0 0 ::.123 ---
::.0 0
UDP 0 0 ::.50056 ---
::.0 0
UDP 0 0 0.0.0.0.1025 ---
0.0.0.0.0 1
UDP 0 0 0.0.0.0.123 ---
0.0.0.0.0 4095
UDP 0 0 0.0.0.0.49152
-------------------------------------------------------------------------------
No. of Connections: 18
===============================================================================
A:ALA-12#
Sample Detailed Output
A:ALA-12# show system connections detail
-------------------------------------------------------------------------------
TCP Statistics
-------------------------------------------------------------------------------
packets sent : 659635
data packets : 338982 (7435146 bytes)
data packet retransmitted : 73 (1368 bytes)
ack-only packets : 320548 (140960 delayed)
URG only packet : 0
window probe packet : 0
window update packet : 0
control packets : 32
packets received : 658893
acks : 338738 for (7435123 bytes)
duplicate acks : 23
ack for unsent data : 0
packets received in-sequence : 334705 (5568368 bytes)
completely duplicate packet : 2 (36 bytes)
packet with some dup. data : 0 (0 bytes)
out-of-order packets : 20 (0 bytes)
packet of data after window : 0 (0 bytes)
window probe : 0
window update packet : 3
packets received after close : 0
discarded for bad checksum : 0
discarded for bad header offset field : 0
discarded because packet too short : 0
connection request : 4
connection accept : 24
connections established (including accepts) : 27
connections closed : 26 (including 2 drops)
embryonic connections dropped : 0
segments updated rtt : 338742 (of 338747 attempts)
retransmit timeouts : 75
connections dropped by rexmit timeout : 0
persist timeouts : 0
keepalive timeouts : 26
keepalive probes sent : 0
connections dropped by keepalive : 1
pcb cache lookups failed : 0
connections dropped by bad md5 digest : 0
connections dropped by enhanced auth : 0
path mtu discovery backoff : 0
===============================================================================
A:ALA-12#
Label |
Description |
---|---|
Proto |
The socket protocol, either TCP or UDP. |
RecvQ |
The number of input packets received by the protocol. |
TxmtQ |
The number of output packets sent by the application. |
Local Address |
The local address of the socket. The socket port is separated by a period. |
Remote Address |
The remote address of the socket. The socket port is separated by a period. |
State |
Listen — The protocol state is in the listen mode. Established — The protocol state is established. vRtrID — The virtual router identifier.
MSS — The TCP maximum segment size. |
connectivity-association
connectivity-association
Syntax
connectivity-association [ca-name] [detail]
Context
[Tree] (show>macsec connectivity-association)
Full Context
show macsec connectivity-association
Description
This command displays MACsec specific CA information.
Parameters
- ca-name
-
Displays MACsec information for the specified CA name, up to 256 characters in length.
- detail
-
Displays MACsec CA detailed information.
Platforms
All