r Commands

Context

[Tree] (config>python>py-policy radius)

Full Context

configure python python-policy radius

Description

This command specifies the Python script for the specified RADIUS packet type in the specified direction.

Multiple radius command configurations are allowed in the same Python policy.

The no form of this command reverts to the default.

Parameters

type

Specifies the message type of the event.

Values

access-request, access-accept, access-reject, accounting-request, accounting-response, access-challenge, disconnect-request, change-of-authorization-request

direction {ingress | egress}

Specifies whether the event is incoming or outgoing.

script

Specifies the name of the Python script, up to 32 characters, that is used to handle the specified message.

Platforms

All

Context

[Tree] (debug>router radius)

Full Context

debug router radius

Description

This command enables the debug router RADIUS context.

Platforms

All

Context

[Tree] (config>service>vprn>aaa>remote-servers radius)

Full Context

configure service vprn aaa remote-servers radius

Description

This command creates the context to configure RADIUS authentication on the VPRN.

Implement redundancy by configuring multiple server addresses for each VPRN.

The no form of this command removes the RADIUS configuration.

Parameters

create

Keyword used to create the RADIUS context.

Platforms

All

Context

[Tree] (config>app-assure>group>transit-ip-policy radius)

Full Context

configure application-assurance group transit-ip-policy radius

Description

This command enables dynamic radius based management of transit aa-subs for the transit-ip-policy. This is mutually exclusive to other types management of transit subs for a given transit-ip-policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>li radius)

Full Context

configure li radius

Description

This command configures RADIUS for Lawful Intercept.

Platforms

All

Context

[Tree] (debug radius)

Full Context

debug radius

Description

This command enables debugging for RADIUS connections.

The no form of the command disables the debug output.

Parameters

detail

Displays detailed output.

hex

Displays the packet dump in hex format.

Platforms

All

Context

[Tree] (config>system>security radius)

Full Context

configure system security radius

Description

This command creates the context to configure RADIUS authentication on the router.

Implement redundancy by configuring multiple server addresses for each router.

The no form of this command removes the RADIUS configuration.

Platforms

All

Context

[Tree] (config>subscr-mgmt>sub-prof radius-accounting)

Full Context

configure subscriber-mgmt sub-profile radius-accounting

Description

Commands in this context configure RADIUS accounting subscriber profile parameters.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>ies>if>sap>ipsec-gw radius-accounting-policy)

[Tree] (config>router>l2tp>group radius-accounting-policy)

[Tree] (config>service>vprn>l2tp>group radius-accounting-policy)

[Tree] (config>router>l2tp>group>tunnel radius-accounting-policy)

[Tree] (config>router>l2tp radius-accounting-policy)

[Tree] (config>service>vprn>l2tp>group>tunnel radius-accounting-policy)

[Tree] (config>service>vprn>l2tp radius-accounting-policy)

[Tree] (config>service>vprn>if>sap>ipsec-gw radius-accounting-policy)

Full Context

configure service ies interface sap ipsec-gw radius-accounting-policy

configure router l2tp group radius-accounting-policy

configure service vprn l2tp group radius-accounting-policy

configure router l2tp group tunnel radius-accounting-policy

configure router l2tp radius-accounting-policy

configure service vprn l2tp group tunnel radius-accounting-policy

configure service vprn l2tp radius-accounting-policy

configure service vprn interface sap ipsec-gw radius-accounting-policy

Description

This command configures the RADIUS accounting policy.

The no form of this command reverts to the default value.

Default

no radius-accounting-policy

Parameters

policy-name

Specifies the policy name, up to 32 characters.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

• configure service vprn interface sap ipsec-gw radius-accounting-policy
• configure service ies interface sap ipsec-gw radius-accounting-policy

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

• configure router l2tp group radius-accounting-policy
• configure service vprn l2tp group tunnel radius-accounting-policy
• configure router l2tp radius-accounting-policy
• configure service vprn l2tp radius-accounting-policy
• configure service vprn l2tp group radius-accounting-policy
• configure router l2tp group tunnel radius-accounting-policy

Context

[Tree] (config>subscr-mgmt radius-accounting-policy)

Full Context

configure subscriber-mgmt radius-accounting-policy

Description

This command specifies a subscriber RADIUS based accounting policy.

The no form of this command removes the policy name from the configuration.

Parameters

name

The name of the policy. The string is case-sensitive and limited to 32 ASCII 7-bit printable characters with no spaces.

create

Keyword used to create a RADIUS accounting policy instance. The create keyword requirement can be enabled/disabled in the environment>create context.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>isa>wlan-gw-group>nat radius-accounting-policy)

Full Context

configure isa wlan-gw-group nat radius-accounting-policy

Description

This command configures the RADIUS accounting policy to use for each MDA in this ISA group.

The no form of this command removes the accounting policy from the configuration.

Parameters

nat-accounting-policy

Specifies the RADIUS accounting policy up to 32 characters.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>app-assure>group>statistics>aa-sub radius-accounting-policy)

Full Context

configure application-assurance group statistics aa-sub radius-accounting-policy

Description

This command specifies an existing subscriber RADIUS based accounting policy to use for AA. RADIUS Accounting policies are configured in the config>app-assure>radius-accounting-policy context.

Default

no radius-accounting-policy

Parameters

rad-acct-plcy-name

Specifies the name of the policy. The string is case sensitive and limited to 32 ASCII 7-bit printable characters with no spaces.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>app-assure radius-accounting-policy)

Full Context

configure application-assurance radius-accounting-policy

Description

This command specifies an existing subscriber RADIUS-based accounting policy to use for AA. RADIUS accounting policies are configured in the config>app-assure>radius-accounting-policy context.

Default

no radius-accounting-policy

Parameters

rad-acct-plcy-name

Specifies the policy name. The string is case sensitive and limited to 32 ASCII 7-bit printable characters with no spaces.

create

Keyword used to create the policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>ipsec radius-accounting-policy)

Full Context

configure ipsec radius-accounting-policy

Description

This command specifies an existing RADIUS accounting policy to use to collect accounting statistics on this subscriber profile by RADIUS. This command is used independently of the collect-stats command.

Parameters

name

Specifies an existing RADIUS based accounting policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>isa>nat-group radius-accounting-policy)

Full Context

configure isa nat-group radius-accounting-policy

Description

This command specifies the RADIUS accounting policy to use for each MDA in this ISA group.

The no form of the command removes the policy ID from the configuration.

Default

no radius-accounting-policy

Parameters

nat-accounting-policy

Reference to the nat-accounting-policy which defines:

Source IP addresses that are assigned to BB-ISA cards.

Parameters related to RADIUS server itself.

List of RADIUS attributes that are included in accounting messages.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>l2tp-acct-plcy>include-radius-attribute radius-accounting-server)

Full Context

configure aaa l2tp-accounting-policy include-radius-attribute radius-accounting-server

Description

Commands in this context configure RADIUS accounting server attributes under a given session authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>l2tp-acct-plcy radius-accounting-server)

[Tree] (config>app-assure>rad-acct-plcy radius-accounting-server)

Full Context

configure aaa l2tp-accounting-policy radius-accounting-server

configure application-assurance radius-accounting-policy radius-accounting-server

Description

This command creates the context for defining RADIUS accounting server attributes under a given session authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

• configure aaa l2tp-accounting-policy radius-accounting-server

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

• configure application-assurance radius-accounting-policy radius-accounting-server

Context

[Tree] (debug>router>radius radius-attr)

Full Context

debug router radius radius-attr

Description

This command specifies the RADIUS attribute filter of command debug router radius.

Parameters

attribute-type

Specifies the RADIUS attribute type.

Values

1 to 255

attribute-ext-type

Specifies the RADIUS attribute extended type (RFC 6929).

Values

1 to 255

address

Specifies the value is a IPv4 or IPv6 address/prefix/subnet.

string

Specifies the value is a ASCII string.

integer

Specifies the value is a integer.

hex

Specifies the value is a binary string in hex format, such as "\0xAB01FE”.

attribute-value

Specifies the value of the RADIUS attribute.

Values

address	<ipv4-address> | <ipv6-address> | <ipv6-prefix/prefix-length>
	ipv4-address	a.b.c.d
	ipv6-address	x:x:x:x:x:x:x:x (eight 16-bit pieces)
	ipv6-prefix	x:x:x:x:x:x:x:x (eight 16-bit pieces)
		x:x:x:x:x:x:d.d.d.d
		x - [0 to FFFF]H
		d - [0 to 255]D
	ipv6-prefix-length [0 to 128]
	hex	[0x0 to 0xFFFFFFFF (up to 506 hex nibbles)]
	integer	[0 to 4294967295]
	string	ascii-string (up to 253 characters)

transaction

Specifies that the system outputs both request and response packets in the same session even if the response packet does not include the filter attribute.

vendor-id

Specifies the vendor id for the vendor specific attribute.

Values

0 to 16777215

encoding-type

Specifies the size of the vendor-type and vendor-length in bytes. It is a two digitals string: "xy”, x is the size of vendor-type, range from 1 to 4; y is the size of vendor-length, range from 0 to 2; it is "11” by default.

Values

type-size:1 to 4, length-size: 0 to 2

Platforms

All

Context

[Tree] (config>subscr-mgmt>gtp>apn-policy>apn radius-auth-policy)

Full Context

configure subscriber-mgmt gtp apn-policy apn radius-auth-policy

Description

This command configures the RADIUS authentication policy with which the GTP connection is authenticated.

The no form of this command removes the authentication policy. Only new session setups are affected.

Default

no radius-auth-policy

Parameters

radius-authentication-policy-name

Specifies the name of the authentication policy to be used, up to 32 characters.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>vrgw>brg>brg-profile radius-authentication)

Full Context

configure subscriber-mgmt vrgw brg brg-profile radius-authentication

Description

Commands in this context configure parameters related to RADIUS authentication performed for the BRG.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vprn>if>sap>ipsec-gw radius-authentication-policy)

[Tree] (config>service>ies>if>sap>ipsec-gw radius-authentication-policy)

Full Context

configure service vprn interface sap ipsec-gw radius-authentication-policy

configure service ies interface sap ipsec-gw radius-authentication-policy

Description

This command specifies the policy to be used for the IKEv2 remote-access tunnels terminated on the IPsec GW. The radius-authentication-policy is defined under config>ipsec context.

Parameters

name

Specifies the name of an existing RADIUS authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>ipsec radius-authentication-policy)

Full Context

configure ipsec radius-authentication-policy

Description

This command specifies the RADIUS authentication policy associated with this IPsec gateway.

Parameters

name

Specifies an existing RADIUS authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>auth-plcy radius-authentication-server)

Full Context

configure subscriber-mgmt authentication-policy radius-authentication-server

Description

Commands in this context define RADIUS authentication server attributes under a given session authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa radius-coa-port)

Full Context

configure aaa radius-coa-port

Description

This command configures the system-wide UDP port number that RADIUS is listening on for CoA and Disconnect messages.

The no form of this command reverts to the default.

Default

radius-coa-port 3799

Parameters

port-number

Specifies the UDP port number for RADIUS CoA and disconnect messages.

Values

1647, 1700, 1812, 3799

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>port>ethernet>dot1x radius-plcy)

Full Context

configure port ethernet dot1x radius-plcy

Description

This command references the RADIUS policy to be used for 802.1x authentication. An 802.1x RADIUS policy must be configured (config>system>security>dot1x) before it can be associated to a port. If the RADIUS policy-id does not exist, an error is returned. Only one 802.1x RADIUS policy can be associated with a port at a time.

The no form of this command removes the RADIUS policy association.

Default

no radius-plcy

Parameters

name

Specifies an existing 802.1x RADIUS policy name, up to 32 characters.

Platforms

All

Context

[Tree] (config>system>security>dot1x radius-plcy)

Full Context

configure system security dot1x radius-plcy

Description

This command creates the context to configure RADIUS server parameters for 802.1x network access control on the router.

The no form of this command removes the RADIUS server configuration for 802.1x.

Platforms

All

Context

[Tree] (config>service>vprn radius-proxy)

[Tree] (config>router radius-proxy)

Full Context

configure service vprn radius-proxy

configure router radius-proxy

Description

This command context to configure RADIUS proxy parameters.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vprn>sub-if>grp-if>wlan-gw>ranges>range>track-mobility radius-proxy-cache)

[Tree] (config>service>ies>sub-if>grp-if>wlan-gw>ranges>range>track-mobility radius-proxy-cache)

Full Context

configure service vprn subscriber-interface group-interface wlan-gw vlan-tag-ranges range track-mobility radius-proxy-cache

configure service ies subscriber-interface group-interface wlan-gw vlan-tag-ranges range track-mobility radius-proxy-cache

Description

This command specifies the RADIUS-proxy server to allow subscribers created via data-triggered authentication to create an entry. This RADIUS proxy cache entry allows efficient handling of UE mobility.

Parameters

router-instance

Specifies the router instance.

Values

router-name	Base
service-id	1 to 2147483647

server-name

Specifies the server name up to 32 characters.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>vrgw>brg>brg-profile radius-proxy-server)

Full Context

configure subscriber-mgmt vrgw brg brg-profile radius-proxy-server

Description

This command enables BRG processing on the specified RADIUS proxy server. Whenever an Access-Accept message is received with the attribute Alc-BRG-Id present, this will trigger the creation of a BRG. The BRG will use the brg-profile specified in the Access-Accept message or fall back to this BRG profile. When the specified radius-proxy-server has a cache enabled, no cache entries will be created for a transaction identified as BRG. A RADIUS proxy server can only be listed in one BRG profile.

This command can be executed multiple times.

The no form of this command removes BRG processing for the specified radius-proxy server.

Parameters

router-instance

Specifies the ID of the VRF where the proxy server is located.

server-name

Specifies the name of the RADIUS proxy server.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>router>nat>inside>subscriber-identification radius-proxy-server)

[Tree] (config>service>vprn>nat>inside>subscriber-identification radius-proxy-server)

Full Context

configure router nat inside subscriber-identification radius-proxy-server

configure service vprn nat inside subscriber-identification radius-proxy-server

Description

This command configures RADIUS proxy server parameters. This is a reference to a RADIUS accounting proxy server in Subscriber Aware Large Scale NAT44 application. RADIUS accounting proxy server will cache attributes related to a BNG subscriber as they are received in standard accounting messages (RFC 2866). Radius accounting proxy server can be configured in any routing instance within 7750 SR.

Parameters

router router-instance

Specifies the routing instance in which the RADIUS accounting proxy is configured.

name server-name

Specifies the name reference to the RADIUS accounting proxy server that is instantiated in 7750 SR.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa radius-script-policy)

Full Context

configure aaa radius-script-policy

Description

This command configures a RADIUS script policy.

The no form of this command removes the script policy from the configuration.

Parameters

policy-name

Configures Python scripts to modify RADIUS messages.

create

This keyword is required when first creating the configuration context. Once the context is created, it is possible to navigate into the context without the create keyword.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vprn radius-server)

[Tree] (config>router radius-server)

Full Context

configure service vprn radius-server

configure router radius-server

Description

Commands in this context configure the RADIUS server under router or VPRN service.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>l2tp-acct-plcy radius-server-policy)

Full Context

configure aaa l2tp-accounting-policy radius-server-policy

Description

This command references an existing radius-server-policy (available under the config>aaa context) for use in subscriber management authentication and accounting.

When configured in an authentication-policy, following CLI commands are ignored in the policy to avoid conflicts:

• all commands in the radius-authentication-server context

• accept-authorization-change

• coa-script-policy

• accept-script-policy

• request-script-policy

When configured in a radius-accounting-policy, following CLI commands are ignored in the policy to avoid conflicts:

• all commands in the radius-accounting-server context

• acct-request-script-policy

The no form of this command removes the radius-server-policy reference from the configuration.

Default

no radius-server-policy

Parameters

policy-name

Specifies the RADIUS server policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa radius-server-policy)

Full Context

configure aaa radius-server-policy

Description

This command creates a radius-server-policy.

A RADIUS server policy can be used in

• radius-proxy, for application like EAP authentication for WIFI access

• authentication policy, for Enhanced Subscriber Management authentication

• radius accounting policy, for Enhanced Subscriber Management accounting

• dynamic data service RADIUS accounting

• AAA route downloader

The no form of this command removes the policy name from the configuration.

Parameters

policy-name

Specifies the name of the radius-server-policy up to 32 characters.

create

Keyword used to create a radius-server-policy name. The create keyword requirement can be enabled/disabled in the environment>create context.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>acct-plcy radius-server-policy)

[Tree] (config>subscr-mgmt>auth-plcy radius-server-policy)

Full Context

configure subscriber-mgmt radius-accounting-policy radius-server-policy

configure subscriber-mgmt authentication-policy radius-server-policy

Description

This command references an existing radius-server-policy (available under the config>aaa context) for use in subscriber management authentication and accounting.

When configured in an authentication-policy, following CLI commands are ignored in the policy to avoid conflicts:

• all commands in the radius-authentication-server context

• accept-authorization-change

• coa-script-policy

• accept-script-policy

• request-script-policy

When configured in a radius-accounting-policy, following CLI commands are ignored in the policy to avoid conflicts:

• all commands in the radius-accounting-server context

• acct-request-script-policy

The no form of this command removes the radius-server-policy reference from the configuration

Parameters

radius-server-policy-name

Specifies the RADIUS server policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>route-downloader radius-server-policy)

Full Context

configure aaa route-downloader radius-server-policy

Description

This command references an existing radius-server-policy (available under the config>aaa context). The server (or servers) referenced by the policy is used as the targets for the access-request message.

The no form of this command removes the policy name from the route-downloader configuration.

Parameters

policy-name

Specifies the RADIUS server policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>vrgw>brg>brg-profile>radius-authentication radius-server-policy)

Full Context

configure subscriber-mgmt vrgw brg brg-profile radius-authentication radius-server-policy

Description

This command is used if the BRG needs to be authenticated to the controller/PCMP by the vRGW. This is required if the BRG does not perform RADIUS authentication via the proxy server. The vRGW will originate a valid Access Request using the BRG ID as the username.

The no form of this command removes the radius-server-policy from the configuration. Setup of an unauthenticated BRG will now fail.

Parameters

policy-name

Specifies the RADIUS server policy, up to 32 characters, to be applied to this subscriber authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>ipsec>rad-acct-plcy radius-server-policy)

[Tree] (config>ipsec>rad-auth-plcy radius-server-policy)

Full Context

configure ipsec radius-accounting-policy radius-server-policy

configure ipsec radius-authentication-policy radius-server-policy

Description

This command references an existing radius-server-policy (available under the config>aaa context) for use in subscriber management authentication and accounting.

When configured in an authentication-policy, following CLI commands are ignored in the policy to avoid conflicts:

• all commands in the radius-authentication-server context

• accept-authorization-change

• coa-script-policy

• accept-script-policy

• request-script-policy

When configured in a radius-accounting-policy, following CLI commands are ignored in the policy to avoid conflicts:

• all commands in the radius-accounting-server context

• acct-request-script-policy

The no form of this command removes the radius-server-policy reference from the configuration.

Default

no radius-server-policy

Parameters

radius-server-policy-name

Specifies the RADIUS server policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>vrgw>brg>brg-profile radius-server-policy)

Full Context

configure subscriber-mgmt vrgw brg brg-profile radius-server-policy

Description

This command allows the vRGW to authenticate on the BRG's behalf. This is required if the BRG does not perform authentication itself using the radius proxy. The vRGW originates a valid Access Request using the BRG ID as a username.

The no form of this command removes the RADIUS server policy from the configuration. Setting up of an unauthenticated BRG will now fail.

Default

no radius-server-policy

Parameters

policy-name

Specifies the RADIUS server policy, up to 32 characters, to apply in this subscriber authentication policy.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>port>ethernet>dot1x radius-server-policy)

Full Context

configure port ethernet dot1x radius-server-policy

Description

This command configures the RADIUS policy with IPv4/IPv6 in base routing and VPRN. The current RADIUS policy can be found under the configure>aaa>radius-server-policy context.

The RADIUS servers for the policy are configured under configure>router>radius-server or configure>service>vprn>radius-server context.

The RADIUS policy is assigned under dot1x using the radius-server-policy command. When the RADIUS policy is configured, both authorization and accounting are performed via the same server.

The no form of this command allows authorization and accounting via different servers.

Default

no radius-server-policy

Parameters

policy-name

Specifies the RADIUS server policy, up to 32 characters.

The policy is configured under configure>aaa>radius-server-policy. When the policy name is configured, both authorization and accounting are done via this server.

policy-name-auth

Specifies the AAA RADIUS server policy for dot1x authorization only; up to 32 characters.

The policy is configured under configure>aaa>radius-server-policy. The policy name authorization is used if the user needs a different server for authorization.

policy-name-acct

Specifies the AAA RADIUS server policy for dot1x accounting only; up to 32 characters.

The policy is configured under configure>aaa>radius-server-policy. The policy name accounting is used if the user needs a different server for accounting.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vprn>sub-if>grp-if>ipoe-session radius-session-timeout)

[Tree] (config>service>ies>sub-if>grp-if>ipoe-session radius-session-timeout)

Full Context

configure service vprn subscriber-interface group-interface ipoe-session radius-session-timeout

configure service ies subscriber-interface group-interface ipoe-session radius-session-timeout

Description

This command specifies how to interpret the session-timeout coming from a RADIUS VSA in an Access-Accept or CoA message.

The value of this command can only be changed on wlan-gw group interfaces.

The no form of this command to resets the default behavior.

Default

radius-session-timeout absolute (backward compatible on wlan-gw group interfaces)

Parameters

backwards-compatible

Specifies that the VSA is interpreted as an IPv4 lease time if the Alc-Lease-Time attribute is not present and an absolute timeout otherwise. The VSA is treated the same as for non-ipoe session DHCP hosts.

ignore

Specifies that the VSA meaning is irrelevant for IPoE session and should be ignored.

absolute

Specifies that the VSA would be treated as a timeout starting from the moment the IPoE session is set up.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>diam-appl-plcy>gy>include-avp radius-user-name)

Full Context

configure subscriber-mgmt diameter-application-policy gy include-avp radius-user-name

Description

This command includes the RADIUS user name AVP in the Diameter Gy messages.

The no form of this command returns the command to the default setting.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>diam-appl-plcy>gx>include-avp rai)

Full Context

configure subscriber-mgmt diameter-application-policy gx include-avp rai

Description

This command enables the inclusion of the RAI AVP as signaled in the incoming GTP setup message.

The no form of this command disables the inclusion of the AVP.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>redundancy>multi-chassis>peer>sync>port range)

Full Context

configure redundancy multi-chassis peer sync port range

Description

This command configures a range of encapsulation values.

Parameters

encap-range

Specifies a range of encapsulation values on a port to be synchronized with a multi-chassis peer.

Values

Dot1Q	start-tag-end-tag
start-tag	0 to 4094
end-tag	0 to 4094
QinQ	qtag1.start-qtag2-qtag1.end-qtag2-start-qtag1.*-end-qtag1.*
qtag1	1 to 4094
start-qtag1	1 to 4094
en-qtag1	1 to 4094
start-qtag2	0 to 4094
end-qtag2	0 to 4094

sync-tag

Specifies a synchronization tag up to 32 characters to be used while synchronizing this encapsulation value range with the multi-chassis peer.

Platforms

All

Context

[Tree] (config>redundancy>multi-chassis>peer>sync>sdp range)

Full Context

configure redundancy multi-chassis peer sync sdp range

Description

This command specifies a range of VC IDs for manually configured spoke SDPs to be synchronized with the multi-chassis peer and a synchronization tag to be used while synchronizing each range with the multi-chassis peer. The range command and the configuration of a synchronization tag on the parent sdp command are mutually exclusive.

To synchronize a single spoke SDP, the start-vc-id should be the same as the end-vc-id. If the configured end-vc-id is lower than the start-vc-id, the range command fails.

The synchronization tag can be changed by entering the same command with a different synchronization tag. Changing the synchronization tag removes all states relating to the previous synchronization tag for the SDP and a new synchronization tag state is created.

Multiple range commands can be configured, however, overlapping ranges for the same SDP (sdp-id) are not permitted.

The synchronization of PIM snooping is only supported for manually configured spoke SDPs but is not supported for spoke SDPs configured within an endpoint. See PIM Snooping for IPv4 Synchronization for service support.

The synchronization of the PIM snooping state is not supported on any of the following when used with the configured sdp-id:

• mesh SDPs

• spoke SDPs in non-VPLS services

• BGP-AD/BGP-VPLS (FEC 129) spoke SDPs

• spoke SDPs configured in endpoints

• pseudowire SAPs

• ESM-over-MPLS pseudowires

Non-existent spoke SDPs may be specified. If these spoke SDPs are created at a later time, then all states on the spoke SDPs are synchronized according to the synchronization tag and the synchronization protocols enabled. The sync-tag can be changed by entering the same command with a different sync-tag value. If the synchronization tag is changed, then all states for the previous sync-tag are removed for the SDP configured in the command and the state is then built for the new synchronization tag.

Parameters

vc-id-range

Specifies a non-overlapping range of VC IDs for the spoke SDPs of the SDP to be synchronized with the multi-chassis peer.

Values

start-vc-id-end-vc-id

start-vc-id: 1 to 4294967295

end-vc-id: 1 to 4294967295

sync-tag

Specifies a synchronization tag, up to 32 characters, to be used when synchronizing with the multi-chassis peer.

Platforms

All

Context

[Tree] (config>redundancy>mc>peer>mcr>ring>path-b range)

[Tree] (config>redundancy>mc>peer>mcr>ring>path-excl range)

Full Context

configure redundancy multi-chassis peer mc-ring ring path-b range

configure redundancy multi-chassis peer mc-ring ring path-excl range

Description

This command configures a Layer 2 MC-Ring path-b or path-excl VLAN range.

By default, all customer VLANs participating in an L2 MC-Ring are on path-a. For load balancing purposes, a range of customer VLANs can be configured to use path-b which is set up in the opposite direction than path-a.The range of VLANs that are not participating in L2 MC-Ring are configured using the path-excl command.

Parameters

vlan-range

Specifies the VLAN range.

Values

[0 to 4094] - [0 to 4094]

[0 to 4094] - *

* - *

Platforms

All

Context

[Tree] (config>service>vpls>sap>managed-vlan-list range)

Full Context

configure service vpls sap managed-vlan-list range

Description

This command configures a range of VLANs on an access port that are to be managed by an existing management VPLS.

This command is only valid when the VPLS in which it is entered was created as a management VPLS, and when the SAP in which it was entered was created on an Ethernet port with encapsulation type of dot1q or qinq, or on a SONET/SDH port with encapsulation type of bcp-dot1q.

To modify the range of VLANs, first the new range should be entered and afterwards the old range removed.

The no form of this command removes the VLAN range from this configuration.

Parameters

vlan-range

Specifies the VLAN start value and VLAN end value. The end-vlan must be greater than start-vlan. The format is <start-vlan>-<end-vlan>.

Values

start-vlan: 1 to 4094

end-vlan: 1 to 4094

Platforms

All

Context

[Tree] (config>service>ies>sub-if>grp-if>wlan-gw>ranges range)

[Tree] (config>service>vprn>sub-if>grp-if>wlan-gw>ranges range)

Full Context

configure service ies subscriber-interface group-interface wlan-gw vlan-tag-ranges range

configure service vprn subscriber-interface group-interface wlan-gw vlan-tag-ranges range

Description

This command creates a VLAN range or enters the context of the specified VLAN ranges for configuration applicable to that range of VLANs.

Parameters

start

Specifies the start of the VLAN range.

Values

0 to 4096

Default

200

end

Specifies the end of VLAN range.

Values

0 to 4096

Default

400

default

Specifies to use defaults for the interface.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vpls>isid-policy>entry range)

Full Context

configure service vpls isid-policy entry range

Description

This command specifies an ISID or a Range of ISIDs in a B-VPLS. One range is allowed per entry.

Default

no range

Parameters

isid

Specifies the ISID value in 24 bits. When singular, ISID identifies a particular ISID to be used for matching

Values

0 to 16777215

to isid

Identifies upper value in a range of ISIDs to be used as matching criteria

Platforms

All

Context

[Tree] (config>service>vpls>sap>static-isid range)

[Tree] (config>service>vpls>spoke-sdp>static-isid range)

Full Context

configure service vpls sap static-isid range

configure service vpls spoke-sdp static-isid range

Description

This command identifies a set of ISIDs for I-VPLS services that are external to SPBM. These ISIDs are advertised as supported locally on this node unless an altered by an isid-policy. This allows communication from I-VPLS services external to SPBM through this node. The SAP may be a regular SAP or MC-LAG SAP. The spoke-SDP may be an active/standby spoke. When used with MC-LAG or active/stand-by PWs the conditional static-mac must be configured. ISIDs declared this way become part of the ISID multicast and consume MFIBs. Multiple SPBM static-isid ranges are allowed under a SAP/spoke-SDP.

The static-isids are associated with a remote B-MAC that must be declared as a static-mac for unicast traffic. ISIDs are advertised as if they were attached to the local B-MAC. Only remote I-VPLS ISIDs need to be defined. In the MFIB, the group MACs are then associated with the active SAP or spoke-SDP. An ISID policy may be defined to suppress the advertisement of an ISID if the ISID is primary used for unicast services. The following rules govern the usage of multiple ISID statements:

• overlapping values are allowed:

  • isid from 301 to 310

  • isid from 305 to 315

  • isid 316

• the minimum and maximum values from overlapping ranges are considered and displayed. The above entries will be equivalent with "ISID from 301 to 316” statement.

• there is no consistency check with the content of ISID statements from other entries. The entries will be evaluated in the order of their IDs and the first match will cause the implementation to execute the associated action for that entry.

The no form of this command removes all the previous statements under one interface

no isid value | from value to higher-value - removes a specific ISID value or range. Must match a previously used positive statement: for example if the command "isid 316 to 400” was used using "no isid 316 to 350” will not work but "no isid 316 to 400 will be successful.

Parameters

range-id

Sets context for specified entry ID for the static-isids

Values

1— 8191

isid-value

Configures the ISID or the start of an ISID range. Specifies the ISID value in 24 bits. When just one present identifies a particular ISID to be used for matching.

Values

0 to 16777215

to isid

Identifies upper value in a range of ISIDs to be used as matching criteria

Values

0 to 16777215

create

This keyword is mandatory when creating a range instance.

Platforms

All

Context

[Tree] (config>qos>sap-ingress>dyn-policer range)

[Tree] (config>qos>sap-egress>dyn-policer range)

Full Context

configure qos sap-ingress dynamic-policer range

configure qos sap-egress dynamic-policer range

Description

This command defines the range of ids for dynamic policers that are created using a Gx interface.

The no form of this command disables creation of dynamic policers using a Gx interface, resulting in a Gx rule instantiation failure, which is the default.

Default

no range

Parameters

start-entry policer-id

Specifies the lowest entry in the range.

Values

1 to 63

count count

Specifies the number of entries in the range.

Values

1 to 63

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>router>mpls>mpls-tp>protection-template rapid-psc-timer)

Full Context

configure router mpls mpls-tp protection-template rapid-psc-timer

Description

This command configures the rapid timer value to be used for protection switching coordination (PSC) packets for MPLS-TP linear protection (RFC 6378).

Default

rapid-psc-timer 10

Parameters

interval

Specifies the rapid timer interval in milliseconds.

Values

[10, 100, 1000]

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>router>gmpls rapid-retransmit-time)

Full Context

configure router gmpls rapid-retransmit-time

Description

This command configures the value of the Rapid Retransmission Interval. It is used in the re-transmission mechanism to handle unacknowledged message_id objects and is based on an exponential back-off timer.

Re-transmission interval of a RSVP message with the same message_id = 2 * rapid-retransmit-time interval of time.

The node stops re-transmission of unacknowledged RSVP messages:

• if the updated back-off interval exceeds the value of the regular refresh interval, or

• if the number of re-transmissions reaches the value of the rapid-retry-limit parameter, whichever comes first

The Rapid Retransmission Interval must be smaller than the regular refresh interval configured in config>router>gmpls>refresh-time.

The no form of this command resets the configuration to the default value.

Default

rapid-retransmit-time 5

Parameters

hundred-milliseconds

Specifies the Rapid Retransmission Interval, in units of 100 ms (for example, enter "6” for a 600 ms retransmit time).

Values

1 to 100

Platforms

7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>router>rsvp rapid-retransmit-time)

Full Context

configure router rsvp rapid-retransmit-time

Description

This command defines the value of the Rapid Retransmission Interval. It is used in the re-transmission mechanism to handle unacknowledged message_id objects and is based on an exponential back-off timer.

Re-transmission interval of a RSVP message with the same message_id = 2 * rapid-retransmit-time interval of time.

The node stops re-transmission of unacknowledged RSVP messages:

• If the updated back-off interval exceeds the value of the regular refresh interval.

• If the number of re-transmissions reaches the value of the rapid-retry-limit parameter, whichever comes first.

The Rapid Retransmission Interval must be smaller than the regular refresh interval configured in config>router>rsvp>refresh-time.

The no form of this command reverts to the default value.

Default

rapid-retransmit-time 5

Parameters

hundred-milliseconds

Specifies the rapid retransmission interval, in hundred-milliseconds (for example, enter "6” for a 600 millisecond retransmit time).

Values

1 to 100, in units of 100 ms.

Platforms

All

Context

[Tree] (config>router>gmpls rapid-retry-limit)

Full Context

configure router gmpls rapid-retry-limit

Description

This command configures the value of the Rapid Retry Limit. This is used in the retransmission mechanism based on an exponential backoff timer in order to handle unacknowledged message_id objects. The RSVP message with the same message_id is retransmitted every 2 * rapid-retransmit-time interval of time. The node will stop retransmission of unacknowledged RSVP messages whenever the updated backoff interval exceeds the value of the regular refresh interval, or the number of retransmissions reaches the value of the rapid-retry-limit parameter, whichever comes first.

The no form of this command resets the configuration to the default value.

Default

rapid-retry-limit 3

Parameters

limit

Specifies the rapid retry limit.

Values

1 to 6

Platforms

7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>router>rsvp rapid-retry-limit)

Full Context

configure router rsvp rapid-retry-limit

Description

This command is used to define the value of the Rapid Retry Limit. This is used in the retransmission mechanism based on an exponential backoff timer in order to handle unacknowledged message_id objects. The RSVP message with the same message_id is retransmitted every 2 * rapid-retransmit-time interval of time. The node will stop retransmission of unacknowledged RSVP messages whenever the updated backoff interval exceeds the value of the regular refresh interval or the number of retransmissions reaches the value of the rapid-retry-limit parameter, whichever comes first.

The no form of this command reverts to the default value.

Default

rapid-retry-limit 3

Parameters

number

Specifies the value of the Rapid Retry Limit.

Values

1 to 6, integer values

Platforms

All

Context

[Tree] (config>router>bgp rapid-update)

Full Context

configure router bgp rapid-update

Description

This command enables and disables BGP rapid update for specified address families.

If rapid update is enabled for a set of address families, and a route belonging to a family in that set is received by the router and chosen for propagation to certain BGP peers, the remaining time on the MRAI timer of these peers is ignored and the route is transmitted immediately, along with all other pending routes for these peers (including routes of address families not specified in the rapid-update command).

The rapid-update command overrides the peer-level min-route-advertisement (config>router>bgp min-route-advertisement, config>router>bgp>group min-route-advertisement, config>router>bgp>group>neighbor min-route-advertisement) time and applies the minimum setting (0 seconds) to routes belonging to specified address families; routes of other address families continue to be advertised according to the session-level MRAI setting.

The no form of this command disables rapid update for all address families.

Default

no rapid-update

Parameters

l2-vpn

Specifies the BGP rapid update for the 12-byte Virtual Switch Instance identifier (VSI-ID) value consisting of the 8-byte route distinguisher (RD) followed by a 4-byte value.

mvpn-ipv4

Specifies BGP rapid update for the mvpn-ipv4 address family. The mvpn-pv4 address is a variable size value consisting of the 1-byte route type, 1-byte length and variable size that is route type specific. Route type defines encoding for the route type specific field. Length indicates the length in octets of the route type specific field.

mdt-safi

Specifies BGP rapid update for the mdt-safi address family. The address is a 16-byte value consisting of 12-byte route distinguisher (RD) followed by a 4-byte group address.

mvpn-ipv6

Specifies BGP rapid update for the mvpn-ipv6 address family.

evpn

Specifies BGP rapid update for the evpn address family by including or removing EVPN routes from the set of routes that can trigger rapid update.

label-ipv4

Includes or removes label-ipv4 routes from the set of routes that can trigger rapid update.

label-ipv6

Includes or removes label-ipv6 routes from the set of routes that can trigger rapid update.

vpn-ipv4

Includes or removes vpn-ipv4 routes from the set of routes that can trigger rapid update.

vpn-ipv6

Includes or removes vpn-ipv6 routes from the set of routes that can trigger rapid update.

mcast-vpn-ipv4

Includes or removes mcast-vpn-ipv4 routes from the set of routes that can trigger rapid update.

mcast-vpn-ipv6

Includes or removes mcast-vpn-ipv6 routes from the set of routes that can trigger rapid update.

Platforms

All

Context

[Tree] (config>service>vprn>bgp rapid-withdrawal)

Full Context

configure service vprn bgp rapid-withdrawal

Description

This command disables the delay (Minimum Route Advertisement) on sending BGP withdrawals. Normal route withdrawals may be delayed up to the minimum route advertisement to allow for efficient packing of BGP updates.

The no form of this command removes this command from the configuration and returns withdrawal processing to the normal behavior.

Default

no rapid-withdrawal

Platforms

All

Context

[Tree] (config>router>bgp rapid-withdrawal)

Full Context

configure router bgp rapid-withdrawal

Description

This command disables the delay (Minimum Route Advertisement) on sending BGP withdrawals. Normal route withdrawals may be delayed up to the minimum route advertisement to allow for efficient packing of BGP updates.

The no form of this command removes this command from the configuration and returns withdrawal processing to the normal behavior.

Default

no rapid-withdrawal

Platforms

All

Context

[Tree] (config>subscr-mgmt>gtp>peer-profile rat-type)

Full Context

configure subscriber-mgmt gtp peer-profile rat-type

Description

This command configures the default Radio Access Type (RAT) signaled during GTP setup. RAT is the underlying physical connection method for a radio-based communication network. This can be overridden by RADIUS.

The no form of this command reverts to the default value.

Default

rat-type wlan

Parameters

utran

Specifies the signaled RAT type is UTRAN (1).

geran

Specifies the signaled RAT type is GERAN (2).

wlan

Specifies the signaled RAT type is WLAN (3).

gan

Specifies the signaled RAT type is GAN (4).

hspa

Specifies the signaled RAT type is HSPA Evolution (5).

eutran

Specifies the signaled RAT type is EUTRAN (6).

virtual

Specifies the signaled RAT type is virtual (7).

id

Specifies the numeric RAT type value.

Values

0 to 255

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>auth-plcy>include-radius-attribute rat-type)

Full Context

configure subscriber-mgmt authentication-policy include-radius-attribute rat-type

Description

This command enables the inclusion of the Radio Access Type in AAA protocols as signaled in the incoming GTP setup message.

The no form of this command disables the inclusion of the attribute.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>diam-appl-plcy>gx>include-avp rat-type)

[Tree] (config>subscr-mgmt>diam-appl-plcy>nasreq>include-avp rat-type)

Full Context

configure subscriber-mgmt diameter-application-policy gx include-avp rat-type

configure subscriber-mgmt diameter-application-policy nasreq include-avp rat-type

Description

This command includes the RAT type.

The no form of this command reverts to the default.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

• configure subscriber-mgmt diameter-application-policy gx include-avp rat-type

7750 SR, 7750 SR-e, 7750 SR-s, VSR

• configure subscriber-mgmt diameter-application-policy nasreq include-avp rat-type

Context

[Tree] (config>subscr-mgmt>sla-prof>egress>qos>hs-wrr-grp rate)

Full Context

configure subscriber-mgmt sla-profile egress qos hs-wrr-group rate

Description

This command configures the rate (PIR) override for the WRR group.

The no form of this command removes the rate from the configuration.

Parameters

rate

Specifies the PIR expressed as a percentage of line rate in kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>subscr-mgmt>sla-prof>egress>qos>queue rate)

Full Context

configure subscriber-mgmt sla-profile egress qos queue rate

Description

This command defines the administrative Peak Information Rate (PIR) and the administrative Committed Information Rate (CIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets out an egress interface (for SAP egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile then out-of-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent command’s cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP egress QoS policy with the queue-id.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Parameters

pir-rate

Defines the administrative PIR rate, in kb/s, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed. Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queues adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 2000000000, max

Default

max

cir-rate

Defines the administrative CIR rate, kb/s, for the queue. The cir parameter overrides the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed. Fractional values are not allowed and must be given as a positive integer.

Values

0 to 2000000000, max

Default

0

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>sla-prof>ingress>qos>queue rate)

Full Context

configure subscriber-mgmt sla-profile ingress qos queue rate

Description

This command defines the administrative Peak Information Rate (PIR) and the administrative Committed Information Rate (CIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the switch fabric (for SAP ingress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. For SAP ingress, the CIR also defines the rate that packets are considered in-profile by the system. In-profile then out-of-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent command’s cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP ingress or SAP egress QoS policy with the queue-id.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Parameters

pir-rate

Defines the administrative PIR rate, in kilobits, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queues adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 2000000000, max

Default

max

cir-rate

Specifies the cir parameter used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be given as a positive integer.

Values

0 to 2000000000, max

Default

0

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>sla-prof>egress>qos>policer rate)

[Tree] (config>subscr-mgmt>sla-prof>ingress>qos>policer rate)

Full Context

configure subscriber-mgmt sla-profile egress qos policer rate

configure subscriber-mgmt sla-profile ingress qos policer rate

Description

This command is used to configure the policer’s metering and optional profiling rates. The metering rate is used by the system to configure the policer’s PIR leaky bucket’s decrement rate while the profiling rate configures the policer’s CIR leaky bucket’s decrement rate. The decrement function empties the bucket while packets applied to the bucket attempt to fill it based on each packets size. If the bucket fills faster than how much is decremented per packet, the bucket’s depth eventually reaches it's exceed (CIR) or violate (PIR) threshold. The cbs, mbs, and high-prio-only commands are used to configure the policer’s PIR and CIR thresholds.

If a packet arrives at the policer while the bucket’s depth is less than the threshold associated with the packet, the packet is considered to be conforming to the bucket’s rate. If the bucket depth is equal to or greater than the threshold, the packet is considered to be in the exception state. For the CIR bucket, the exception state is exceeding the CIR rate while the PIR bucket's exception state is violating the PIR bucket rate. If the packet is violating the PIR, the packet is marked red and is discarded. If the packet is not red, it may be green or yellow based on the conforming or exceeding state from the CIR bucket.

When a packet is red neither the PIR or CIR bucket depths are incremented by the packets size. When the packet is yellow the PIR bucket is incremented by the packet size, but the CIR bucket is not. When the packet is green, both the PIR and CIR buckets are incremented by the packet size. This ensures that conforming packets impact the bucket depth while exceeding or violating packets do not.

The policer’s adaptation-rule command settings are used by the system to convert the specified rates into hardware timers and decrement values for the policer’s buckets.

By default, the policer’s metering rate is max and the profiling rate is 0 kb/s (all packets out-of-profile).

The rate settings defined for the policer in the QoS policy may be overridden on an sla-profile or SAP where the policy is applied.

The no form of this command restores the default metering and profiling rate to a policer.

Parameters

{max | rate}

Specifies the packet byte offset. Specifying the keyword max or an explicit rate (in kilobits per second) parameter directly following the rate command is required and identifies the policer’s metering rate for the PIR leaky bucket. When the policer is first created, the metering rate defaults to max. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used is equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

max or 1 to 2000000000

cir {max | rate}

Specifies the packet byte offset. The optional cir keyword is used to override the default CIR rate of the policer. Specifying the keyword max or an explicit rate (in kilobits per second) parameter directly following the cir keyword is required and identifies the policer’s profiling rate for the CIR leaky bucket. When the policer is first created, the profiling rate defaults to 0 kb/s. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used is equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

max or 0 to 2000000000

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vprn>sub-if>grp-if>sap>egress>agg-rate rate)

[Tree] (config>service>ies>if>sap>egress>agg-rate rate)

[Tree] (config>service>ies>sub-if>grp-if>sap>egress>agg-rate rate)

Full Context

configure service vprn subscriber-interface group-interface sap egress agg-rate rate

configure service ies interface sap egress agg-rate rate

configure service ies subscriber-interface group-interface sap egress agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object (SAP, subscriber, Vport, and so on).

The no form of this command removes an explicit rate value from the aggregate rate therefore returning it to its default value.

Parameters

kilobits-per-second

Specifies the rate limit for the SAP, in kilobits per second.

Values

1 to 6400000000, max

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

• configure service vprn subscriber-interface group-interface sap egress agg-rate rate
• configure service ies subscriber-interface group-interface sap egress agg-rate rate

All

• configure service ies interface sap egress agg-rate rate

Context

[Tree] (config>service>ies>if>sap>ingress>queue-override>queue rate)

[Tree] (config>service>vpls>sap>ingress>queue-override>queue rate)

[Tree] (config>service>ies>if>sap>egress>queue-override>queue rate)

[Tree] (config>service>vpls>sap>egress>queue-override>queue rate)

Full Context

configure service ies interface sap ingress queue-override queue rate

configure service vpls sap ingress queue-override queue rate

configure service ies interface sap egress queue-override queue rate

configure service vpls sap egress queue-override queue rate

Description

This command overrides specific attributes of the specified queue’s Peak Information Rate (PIR) and the Committed Information Rate (CIR) parameters.

The PIR defines the maximum rate that the queue can transmit packets out an egress interface (for SAP egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile, then out-of-profile, packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP egress QoS policy with the queue-id.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Default

rate max cir 0

Parameters

pir-rate

Defines the administrative PIR rate, in kilobits, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 6400000000, max

Default

max

cir-rate

Overrides the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be given as a positive integer.

Values

0 to 6400000000, max

Default

0

Platforms

All

Context

[Tree] (config>service>vpls>sap>egress>sched-override>scheduler rate)

Full Context

configure service vpls sap egress scheduler-override scheduler rate

Description

This command overrides specific attributes of the specified scheduler rate. The rate command defines the maximum bandwidth that the scheduler can offer its policers, child queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the amount of bandwidth to be considered during the parent scheduler’s 'within CIR’ distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler’s parent scheduler may not have the available bandwidth to meet the scheduler’s needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler assumes that an infinite amount of bandwidth is available and allow all child queues and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler's PIR and CIR parameters to the value configured in the applied scheduler policy.

Default

rate max cir sum

Parameters

pir-rate

Specifies the PIR rates. The pir parameter accepts a step multiplier value that specifies the multiplier used to determine the PIR rate at which the queue operates. A value of 0 to 100000000 or the keyword max is accepted. Any other value results in an error without modifying the current PIR rate.

To calculate the actual PIR rate, the rate described by the queue’s rate is multiplied by the pir-rate.

The SAP ingress context for PIR is independent of the defined forwarding class (fc) for the queue. The default pir and definable range is identical for each class. The PIR in effect for a queue defines the maximum rate at which the queue is allowed to forward packets in a given second, thus shaping the queue’s output.

The PIR parameter for SAP ingress queues do not have a negate (no) function. To return the queue’s PIR rate to the default value, that value must be specified as the PIR value.

Values

1 to 6400000000, max

Default

max

cir-rate

Specifies the CIR rate. The cir parameter accepts a step-multiplier value that specifies the multiplier used to determine the CIR rate at which the queue operate. A value of 0 to 250 or the keyword max is accepted. Any other value results in an error without modifying the current CIR rate.

To calculate the actual CIR rate, the rate described by the rate pir pir-rate is multiplied by the cir-rate. If the cir is set to max, then the CIR rate is set to infinity.

The context for CIR is dependent on the defined forwarding class (fc) for the queue. The default CIR and definable range is different for each class. The CIR in effect for a policer or queue defines both its profile (in or out) marking level as well as the relative importance compared to other queues for scheduling purposes during congestion periods.

Values

0 to 6400000000, max, sum

Default

sum

Platforms

All

Context

[Tree] (config>subscr-mgmt>isa-policer rate)

Full Context

configure subscriber-mgmt isa-policer rate

Description

This command specifies at which rate the policer drains packets. The cir value is only supported on dual-bucket-bandwidth policers. If rate max is configured, no actual rate limitations are applied.

The no form of this command reverts to the default.

Parameters

rate

Specifies the rate in kb/s.

Values

1 to 100000000, max

Default

max

cir-rate

Specifies the CIR rate in kb/s.

Values

1 to 100000000, max

Default

max

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>vprn>sub-if>grp-if>wlan-gw>egress>agg-rate rate)

[Tree] (config>service>ies>sub-if>grp-if>wlan-gw>egress>agg-rate rate)

Full Context

configure service vprn subscriber-interface group-interface wlan-gw egress agg-rate rate

configure service ies subscriber-interface group-interface wlan-gw egress agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object (SAP, subscriber, Vport, and so on).

The no form of this command reverts to the default.

Context

[Tree] (config>card>fp>ingress>access>qgrp>policer-over>plcr rate)

[Tree] (config>card>fp>ingress>network>qgrp>policer-over>plcr rate)

Full Context

configure card fp ingress access queue-group policer-override policer rate

configure card fp ingress network queue-group policer-override policer rate

Description

This command configures the policer’s metering and optional profiling rates. The metering rate is used by the system to configure the policer’s PIR leaky bucket’s decrement rate while the profiling rate configures the policer’s CIR leaky bucket’s decrement rate. The decrement function empties the bucket while packets applied to the bucket attempt to fill it based on its packet size. If the bucket fills faster than how much is decremented per packet, the bucket’s depth eventually reaches it's exceeded (CIR) or violate (PIR) threshold. The cbs, mbs, and high-prio-only commands are used to configure the policer’s PIR and CIR thresholds.

If a packet arrives at the policer while the bucket’s depth is less than the threshold associated with the packet, the packet is considered to be conforming to the bucket’s rate. If the bucket depth is equal to or greater than the threshold, the packet is considered to be in the exception state. For the CIR bucket, the exception state is exceeding the CIR rate while the PIR bucket's exception state is violating the PIR bucket rate. If the packet is violating the PIR, the packet is marked red and will be discarded. If the packet is not red, it may be green or yellow based on the conforming or exceeding state from the CIR bucket.

When a packet is red neither the PIR nor the CIR bucket depths are incremented by the packets size. When the packet is yellow the PIR bucket is incremented by the packet size, but the CIR bucket is not. When the packet is green, both the PIR and CIR buckets are incremented by the packet size. This ensures that conforming packets impact the bucket depth while exceeding or violating packets do not.

The policer’s adaptation-rule command settings are used by the system to convert the specified rates into hardware timers and decrement values for the policer’s buckets.

By default, the policer’s metering rate is max and the profiling rate is 0 kb/s (all packets out-of-profile).

The rate settings defined for the policer in the QoS policy may be overridden on an sla-profile or SAP where the policy is applied.

The no form of this command reverts to the default metering and profiling rate of a policer.

Parameters

{rate | max}

Specifying the keyword max or an explicit rate parameter directly following the rate command is required and identifies the policer’s metering rate for the PIR leaky bucket. When the policer is first created, the metering rate defaults to max. The kilobits-per-second value must be expressed as an integer and defines the rate in kilobits-per-second. The integer value is multiplied by 1,000 to derive the actual rate in bits-per-second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

max or 1 to 2000000000

cir {max | rate}

The optional cir keyword is used to override the default CIR rate of the policer. Specifying the keyword max or an explicit rate parameter directly following the cir keyword is required and identifies the policer’s profiling rate for the CIR leaky bucket. When the policer is first created, the profiling rate defaults to 0 kb/s. The kilobits-per-second value must be expressed as an integer and defines the rate in kilobits-per-second. The integer value is multiplied by 1,000 to derive the actual rate in bits-per-second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

max or 0 to 2000000000

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>port>ethernet>access>egr>qgrp>agg-rate rate)

[Tree] (config>port>ethernet>network>egr>qgrp>agg-rate rate)

Full Context

configure port ethernet access egress queue-group agg-rate rate

configure port ethernet network egress queue-group agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object.

The no form of this command removes an explicit rate value from the aggregate rate returning it to its default value.

Parameters

kilobits-per-second

Specifies the rate limit for the queue group, in kilobits per second.

Values

1 to 3200000000, max

Platforms

All

Context

[Tree] (config>port>ethernet>access>egr>vport>agg-rate rate)

Full Context

configure port ethernet access egress vport agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object.

The no form of this command removes an explicit rate value from the aggregate rate returning it to its default value.

Parameters

kilobits-per-second

Specifies the rate limit for the Vport, in kilobits per second.

Values

1 to 6400000000, max

Platforms

All

Context

[Tree] (config>port>ethernet>network>egr>qover>q rate)

[Tree] (config>port>ethernet>access>egr>qgrp>qover>q rate)

[Tree] (config>port>ethernet>access>ing>qgrp>qover>q rate)

Full Context

configure port ethernet network egress queue-overrides queue rate

configure port ethernet access egress queue-group queue-overrides queue rate

configure port ethernet access ingress queue-group queue-overrides queue rate

Description

This command specifies the administrative Peak Information Rate (PIR) and the administrative Committed Information Rate (CIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets out an egress interface (for SAP egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile then out-of-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP egress QoS policy with the queue-id.

This command is ignored for egress HSQ queue group queues which are attached to an HS WRR group within an associated HS attachment policy. In this case, the configuration of the rate is performed under the hs-wrr-group within the egress queue group template.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Default

rate max cir 0 - The max default specifies the amount of bandwidth in kilobits per second (thousand bits per second). The max value is mutually exclusive to the pir-rate value.

Parameters

pir-rate

Defines the administrative PIR rate, in kilobits per second, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed. Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 200000000, max

Default

max

cir-rate

The cir parameter overrides the default administrative CIR used by the queue, in kilobits per second. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed. Fractional values are not allowed and must be given as a positive integer.

Values

0 to 200000000, max

Default

0

Platforms

All

Context

[Tree] (config>port>ethernet>access>ing>qgrp>sched-override>scheduler rate)

[Tree] (config>port>ethernet>access>egr>qgrp>sched-override>scheduler rate)

Full Context

configure port ethernet access ingress queue-group scheduler-override scheduler rate

configure port ethernet access egress queue-group scheduler-override scheduler rate

Description

This command can be used to override specific attributes of the specified scheduler rate. The rate command defines the maximum bandwidth that the scheduler can offer its child queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the amount of bandwidth to be considered during the parent scheduler's 'within CIR' distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler's parent scheduler may not have the available bandwidth to meet the scheduler's needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler will assume that an infinite amount of bandwidth is available and allow all child policers, queues, and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler's PIR and CIR parameters to the value configured in the applied scheduler policy.

Parameters

pir-rate

Specifies the PIR rate, in kilobits per second. Any other value will result in an error without modifying the current PIR rate.

Values

1 to 6400000000, max

cir-rate

Specifies the CIR rate, in kilobits per second. If the CIR is set to max, then the CIR rate is set to infinity. The sum keyword specifies that the CIR be used as the summed CIR values of the children schedulers, policers, or queues.

Values

0 to 6400000000, sum, max

Platforms

All

Context

[Tree] (config>port>ethernet>egress>hs-sec-shaper>agg rate)

[Tree] (config>port>ethernet>egress>hs-sec-shaper>class rate)

Full Context

configure port ethernet egress hs-secondary-shaper aggregate rate

configure port ethernet egress hs-secondary-shaper class rate

Description

This command specifies the rate allowed for the HS secondary shaper's aggregate rate and per-class rates.

The no form of this command reverts to the default.

Default

rate max

Parameters

rate

Specifies the maximum rate in kilobits per second. When the max keyword follows the rate keyword, the bandwidth limitation is removed from the aggregate or class. The max keyword is mutually exclusive to the rate parameter. Either max or a rate value must follow the rate keyword.

Values

1 to 100000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>service>apipe>sap>egress>agg-rate rate)

[Tree] (config>service>fpipe>sap>egress>agg-rate rate)

[Tree] (config>service>epipe>sap>egress>agg-rate rate)

[Tree] (config>service>cpipe>sap>egress>agg-rate rate)

[Tree] (config>service>ipipe>sap>egress>agg-rate rate)

Full Context

configure service apipe sap egress agg-rate rate

configure service fpipe sap egress agg-rate rate

configure service epipe sap egress agg-rate rate

configure service cpipe sap egress agg-rate rate

configure service ipipe sap egress agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object (SAP, subscriber, Vport, and so on).

The no form of this command removes an explicit rate value from the aggregate rate returning it to its default value.

Parameters

kilobits-per-second

The enforced aggregate rate for all queues associated with the agg-rate context, in kilobits per second.

Values

1 to 6400000000, max

Platforms

7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e, 7950 XRS

• configure service apipe sap egress agg-rate rate

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

• configure service cpipe sap egress agg-rate rate
• configure service fpipe sap egress agg-rate rate

All

• configure service epipe sap egress agg-rate rate
• configure service ipipe sap egress agg-rate rate

Context

[Tree] (config>service>epipe>sap>ingress>policer-over>plcr rate)

[Tree] (config>service>ipipe>sap>ingress>policer-over>plcr rate)

[Tree] (config>service>fpipe>sap>ingress>policer-over>plcr rate)

[Tree] (config>service>fpipe>sap>egress>policer-over>plcr rate)

[Tree] (config>service>epipe>sap>egress>policer-over>plcr rate)

[Tree] (config>service>ipipe>sap>egress>policer-over>plcr rate)

[Tree] (config>service>apipe>sap>egress>policer-over>plcr rate)

[Tree] (config>service>cpipe>sap>egress>policer-over>plcr rate)

[Tree] (config>service>cpipe>sap>ingress>policer-over>plcr rate)

[Tree] (config>service>apipe>sap>ingress>policer-over>plcr rate)

Full Context

configure service epipe sap ingress policer-override policer rate

configure service ipipe sap ingress policer-override policer rate

configure service fpipe sap ingress policer-override policer rate

configure service fpipe sap egress policer-override policer rate

configure service epipe sap egress policer-override policer rate

configure service ipipe sap egress policer-override policer rate

configure service apipe sap egress policer-override policer rate

configure service cpipe sap egress policer-override policer rate

configure service cpipe sap ingress policer-override policer rate

configure service apipe sap ingress policer-override policer rate

Description

This command within the SAP ingress and egress policer-overrides contexts is used to override the sap-ingress and sap-egress QoS policy configured rate parameters for the specified policer-id.

The no rate command is used to restore the policy defined metering and profiling rate to a policer.

Parameters

rate rate

Specifies the policer instance metering rate for the PIR leaky bucket, in kilobits per second. The integer value is multiplied by 1000 to derive the actual rate in bits per second.

Values

1 to 6400000000

cir rate

Specifies the overriding value for the policy-derived profiling rate of the policer, in kilobits per second. The integer value is multiplied by 1000 to derive the actual rate in bits per second.

Values

0 to 6400000000

max

Uses the maximum policer rate, equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR or CIR used is equivalent to max.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

• configure service ipipe sap egress policer-override policer rate
• configure service epipe sap egress policer-override policer rate
• configure service epipe sap ingress policer-override policer rate
• configure service ipipe sap ingress policer-override policer rate

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS

• configure service cpipe sap egress policer-override policer rate
• configure service cpipe sap ingress policer-override policer rate
• configure service fpipe sap egress policer-override policer rate
• configure service fpipe sap ingress policer-override policer rate

7450 ESS, 7750 SR-7/12/12e, 7750 SR-e, 7950 XRS

• configure service apipe sap ingress policer-override policer rate
• configure service apipe sap egress policer-override policer rate

Context

[Tree] (config>service>epipe>sap>egress>queue-override>hs-wrr-group rate)

[Tree] (config>service>ipipe>sap>egress>queue-override>hs-wrr-group rate)

Full Context

configure service epipe sap egress queue-override hs-wrr-group rate

configure service ipipe sap egress queue-override hs-wrr-group rate

Description

This command overrides the scheduling rate applied to the HS WRR group in kb/s. A rate can be specified in kb/s or the keyword max can be used to remove the bandwidth limitation on the HS WRR group. The override rate type must match the corresponding rate type within the applied QoS policy.

The no form of this command removes the rate override value from the configuration.

Parameters

rate

Specifies the scheduling rate of the HS WRR group in kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>service>epipe>sap>egress>queue-override>queue rate)

[Tree] (config>service>cpipe>sap>egress>queue-override>queue rate)

[Tree] (config>service>ipipe>sap>ingress>queue-override>queue rate)

[Tree] (config>service>cpipe>sap>ingress>queue-override>queue rate)

[Tree] (config>service>fpipe>sap>ingress>queue-override>queue rate)

[Tree] (config>service>apipe>sap>egress>queue-override>queue rate)

[Tree] (config>service>apipe>sap>ingress>queue-override>queue rate)

[Tree] (config>service>epipe>sap>ingress>queue-override>queue rate)

[Tree] (config>service>fpipe>sap>egress>queue-override>queue rate)

[Tree] (config>service>ipipe>sap>egress>queue-override>queue rate)

Full Context

configure service epipe sap egress queue-override queue rate

configure service cpipe sap egress queue-override queue rate

configure service ipipe sap ingress queue-override queue rate

configure service cpipe sap ingress queue-override queue rate

configure service fpipe sap ingress queue-override queue rate

configure service apipe sap egress queue-override queue rate

configure service apipe sap ingress queue-override queue rate

configure service epipe sap ingress queue-override queue rate

configure service fpipe sap egress queue-override queue rate

configure service ipipe sap egress queue-override queue rate

Description

This command can be used to override specific attributes of the specified queue’s Peak Information Rate (PIR) and the Committed Information Rate (CIR) parameters.

The PIR defines the maximum rate that the queue can transmit packets out an egress interface (for SAP egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile and then out-of-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP egress QoS policy with the queue-id.

This command is ignored for egress HSQ queue group queues which are attached to an HS WRR group within an associated HS attachment policy. In this case, the configuration of the rate is performed under the hs-wrr-group within the SAP egress QoS policy.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Default

rate max cir 0

Parameters

pir-rate

Defines the administrative PIR rate, in kilobits per second, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 6400000000, max

Default

max

cir-rate

The cir parameter overrides the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be given as a positive integer. The sum keyword specifies that the CIR be used as the summed CIR values of the children schedulers, policers, or queues.

Values

0 to 6400000000, max, sum

Default

0

Platforms

All

• configure service epipe sap ingress queue-override queue rate
• configure service epipe sap egress queue-override queue rate
• configure service ipipe sap egress queue-override queue rate
• configure service ipipe sap ingress queue-override queue rate

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

• configure service fpipe sap egress queue-override queue rate
• configure service cpipe sap egress queue-override queue rate
• configure service cpipe sap ingress queue-override queue rate
• configure service fpipe sap ingress queue-override queue rate

7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e, 7950 XRS

• configure service apipe sap egress queue-override queue rate
• configure service apipe sap ingress queue-override queue rate

Context

[Tree] (config>service>epipe>sap>egress>sched-override>scheduler rate)

[Tree] (config>service>apipe>sap>egress>sched-override>scheduler rate)

[Tree] (config>service>cpipe>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>fpipe>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>cpipe>sap>egress>sched-override>scheduler rate)

[Tree] (config>service>apipe>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>fpipe>sap>egress>sched-override>scheduler rate)

[Tree] (config>service>ipipe>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>epipe>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>ipipe>sap>egress>sched-override>scheduler rate)

Full Context

configure service epipe sap egress scheduler-override scheduler rate

configure service apipe sap egress scheduler-override scheduler rate

configure service cpipe sap ingress scheduler-override scheduler rate

configure service fpipe sap ingress scheduler-override scheduler rate

configure service cpipe sap egress scheduler-override scheduler rate

configure service apipe sap ingress scheduler-override scheduler rate

configure service fpipe sap egress scheduler-override scheduler rate

configure service ipipe sap ingress scheduler-override scheduler rate

configure service epipe sap ingress scheduler-override scheduler rate

configure service ipipe sap egress scheduler-override scheduler rate

Description

This command can be used to override specific attributes of the specified scheduler rate. The rate command defines the maximum bandwidth that the scheduler can offer its child policers, queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the amount of bandwidth to be considered during the parent scheduler’s 'within CIR’ distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler’s parent scheduler may not have the available bandwidth to meet the scheduler’s needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child policers or queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler will assume that an infinite amount of bandwidth is available and allow all child policers, queues, and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler’s PIR and CIR parameters to the values configured in the applied scheduler policy.

Parameters

pir-rate

The pir parameter accepts the max keyword or a value in kilobits per second. Any other value will result in an error without modifying the current PIR rate.

Values

1 to 6400000000, max

cir cir-rate

The cir parameter accepts a value in kilobits per second or the max keyword. Any other value will result in an error without modifying the current CIR rate.

If the cir parameter is set to max, then the CIR rate is set to infinity but bounded by the PIR rate.

The sum keyword specifies that the CIR will be used as the summed CIR values of the children schedulers, policers, or queues.

Values

0 to 6400000000, max, sum

Platforms

All

• configure service ipipe sap ingress scheduler-override scheduler rate
• configure service ipipe sap egress scheduler-override scheduler rate
• configure service epipe sap egress scheduler-override scheduler rate
• configure service epipe sap ingress scheduler-override scheduler rate

7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e, 7950 XRS

• configure service apipe sap ingress scheduler-override scheduler rate
• configure service apipe sap egress scheduler-override scheduler rate

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

• configure service fpipe sap egress scheduler-override scheduler rate
• configure service fpipe sap ingress scheduler-override scheduler rate
• configure service cpipe sap ingress scheduler-override scheduler rate
• configure service cpipe sap egress scheduler-override scheduler rate

Context

[Tree] (config>service>vpls>sap>egress>encap-defined-qos>encap-group>agg-rate rate)

[Tree] (config>service>template>vpls-sap-template>egress>agg-rate rate)

[Tree] (config>service>vpls>sap>egress>agg-rate rate)

Full Context

configure service vpls sap egress encap-defined-qos encap-group agg-rate rate

configure service template vpls-sap-template egress agg-rate rate

configure service vpls sap egress agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered active on the context’s object (SAP, subscriber, Vport, and so on.).

The no form of this command removes an explicit rate value from the aggregate rate returning it to its default value.

Parameters

kilobits-per-second

The enforced aggregate rate for all queues associated with the agg-rate context, in kilobits per second.

Values

1 to 6400000000, max

Platforms

All

Context

[Tree] (config>service>vpls>sap>ingress>policer-override>plcr rate)

[Tree] (config>service>vpls>sap>egress>policer-override>plcr rate)

Full Context

configure service vpls sap ingress policer-override policer rate

configure service vpls sap egress policer-override policer rate

Description

This command within the SAP ingress and egress policer-overrides contexts is used to override the sap-ingress and sap-egress QoS policy configured rate parameters for the specified policer-id.

The no form of this command removes the rate override so that the rate configured for the policer in the applied SAP egress QoS policy is used.

Parameters

{rate | max}

Specifying the keyword max or an explicit kilobits per second parameter directly following the rate override command is required and identifies the policer instance’s metering rate for the PIR leaky bucket. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

1 to 6400000000, max

cir {max | rate}

The optional cir keyword is used to override the policy derived profiling rate of the policer. Specifying the keyword max or an explicit kilobits per second parameter directly following the cir keyword is required. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

0 to 6400000000, max

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>service>vpls>sap>egress>queue-override>hs-wrr-group rate)

Full Context

configure service vpls sap egress queue-override hs-wrr-group rate

Description

This command overrides the scheduling rate applied to the HS WRR group in kb/s. Alternatively, the keyword max can be specified which removes the bandwidth limitation on the HS WRR group. The override rate type must match the corresponding rate type within the applied QoS policy.

The no form of this command removes the rate override value from the configuration.

Parameters

rate

Specifies the scheduling rate of the HS WRR group in kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>service>ies>if>sap>ingress>policer-override>plcr rate)

[Tree] (config>service>ies>if>sap>egress>policer-override>plcr rate)

Full Context

configure service ies interface sap ingress policer-override policer rate

configure service ies interface sap egress policer-override policer rate

Description

This command within the SAP ingress and egress policer-overrides contexts is used to override the sap-ingress and sap-egress QoS policy configured rate parameters for the specified policer-id.

The no form of the command removes the rate override so that the rate configured for the policer in the applied SAP egress QoS policy is used.

Parameters

{rate | max}

Specifying the keyword max or an explicit kilobits per second parameter directly following the rate override command is required and identifies the policer instance’s metering rate for the PIR leaky bucket. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

1 to 6400000000, max

cir {max | rate}

The optional cir keyword is used to override the policy derived profiling rate of the policer. Specifying the keyword max or an explicit kilobits per second parameter directly following the cir keyword is required. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

0 to 6400000000, max

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>service>ies>if>sap>egress>queue-override>hs-wrr-group rate)

Full Context

configure service ies interface sap egress queue-override hs-wrr-group rate

Description

This command overrides the scheduling rate applied to the HS WRR group in Kb/s. Alternatively, the keyword max can be specified which removes the bandwidth limitation on the HS WRR group. The override rate type must match the corresponding rate type within the applied QoS policy.

The no form of this command removes the rate override value from the configuration.

Parameters

rate

Specifies the scheduling rate of the HS WRR group in Kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>service>ies>if>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>ies>if>sap>egress>sched-override>scheduler rate)

Full Context

configure service ies interface sap ingress scheduler-override scheduler rate

configure service ies interface sap egress scheduler-override scheduler rate

Description

This command can be used to override specific attributes of the specified scheduler rate. The rate command defines the maximum bandwidth that the scheduler can offer its child queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the amount of bandwidth to be considered during the parent scheduler’s 'within CIR’ distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler’s parent scheduler may not have the available bandwidth to meet the scheduler’s needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler will assume that an infinite amount of bandwidth is available and allow all child queues and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler's PIR and CIR parameters to the value configured in the applied scheduler policy.

Parameters

pir-rate

The pir parameter accepts a value in kilobits per second, or the keyword max. Any other value will result in an error without modifying the current PIR rate.

Values

1 to 6400000000, max

cir-rate

This parameter accepts a step-multiplier value that specifies the multiplier used to determine the CIR rate at which the queue will operate. A value in kilobits per second or the keywords max or sum is accepted. Any other value will result in an error without modifying the current CIR rate.

If the cir is set to max, then the CIR rate is set to infinity but is restricted by the PIR rate.

The sum keyword specifies that the CIR be used as the summed CIR values of the children schedulers, policers, or queues.

For egress>sched-override>scheduler and ingress>sched-override>scheduler:

Values

0 to 6400000000, max, sum

Platforms

All

Context

[Tree] (config>service>vprn>if>sap>egress>agg-rate rate)

Full Context

configure service vprn interface sap egress agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object.

The no form of this command removes an explicit rate value from the aggregate rate returning it to its default value.

Parameters

kilobits-per-second

Specifies the rate limit for the SAP, in kilobits per second.

Values

1 to 6400000000, max

Platforms

All

Context

[Tree] (config>service>vprn>if>sap>ingress>policer-override>plcr rate)

[Tree] (config>service>vprn>if>sap>egress>policer-override>plcr rate)

Full Context

configure service vprn interface sap ingress policer-override policer rate

configure service vprn interface sap egress policer-override policer rate

Description

This command within the SAP ingress and egress policer-overrides contexts is used to override the sap-ingress and sap-egress QoS policy configured rate parameters for the specified policer-id.

The no form of this command restores the policy defined metering and profiling rate to a policer.

Parameters

{rate | max}

Specifying the keyword max or an explicit kilobits per second parameter directly following the rate override command is required and identifies the policer instance’s metering rate for the PIR leaky bucket. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

1 to 6400000000, max

cir {max | rate}

The optional cir keyword is used to override the policy derived profiling rate of the policer. Specifying the keyword max or an explicit kilobits per second parameter directly following the cir keyword is required. The kilobits per second value must be expressed as an integer and defines the rate in kilobits per second. The integer value is multiplied by 1,000 to derive the actual rate in bits per second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

0 to 6400000000, max

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>service>vprn>if>sap>egress>queue-override>hs-wrr-group rate)

Full Context

configure service vprn interface sap egress queue-override hs-wrr-group rate

Description

This command overrides the scheduling rate applied to the HS WRR group in Kb/s. Alternatively, the keyword max can be specified which removes the bandwidth limitation on the HS WRR group. The override rate type must match the corresponding rate type within the applied QoS policy.

The no form of this command removes the rate override value from the configuration.

Parameters

rate

Specifies the scheduling rate of the HS WRR group in Kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>service>vprn>if>sap>egress>queue-override>queue rate)

[Tree] (config>service>vprn>if>sap>ingress>queue-override>queue rate)

Full Context

configure service vprn interface sap egress queue-override queue rate

configure service vprn interface sap ingress queue-override queue rate

Description

This command can be used to override specific attributes of the specified queue’s Peak Information Rate (PIR) and the Committed Information Rate (CIR) parameters. The PIR defines the maximum rate that the queue can transmit packets out an egress interface (for SAP egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP egress QoS policy with the queue-id.

This command is ignored for egress HSQ queue group queues which are attached to an HS WRR group within an associated HS attachment policy. In this case, the configuration of the rate is performed under the hs-wrr-group within the SAP egress QoS policy.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Default

rate max cir 0

Parameters

pir-rate

Defines the administrative PIR rate, in kb/s, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 6400000000, max

Default

max

cir-rate

Defines the administrative CIR rate, in kb/s, for the queue. The cir parameter overrides the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be given as a positive integer.

Values

0 to 6400000000, max

Default

0

Platforms

All

Context

[Tree] (config>service>vprn>if>sap>ingress>sched-override>scheduler rate)

[Tree] (config>service>vprn>if>sap>egress>sched-override>scheduler rate)

Full Context

configure service vprn interface sap ingress scheduler-override scheduler rate

configure service vprn interface sap egress scheduler-override scheduler rate

Description

This command can be used to override specific attributes of the specified scheduler rate. The rate command defines the maximum bandwidth that the scheduler can offer its child queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the amount of bandwidth to be considered during the parent scheduler’s 'within CIR’ distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler’s parent scheduler may not have the available bandwidth to meet the scheduler’s needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child policers and queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler will assume that an infinite amount of bandwidth is available and allow all child queues and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler's PIR and CIR parameters to the value configured in the applied scheduler policy.

Parameters

pir-rate

Specifies the PIR rate for the scheduler. The pir parameter accepts a value in kb/s, or the max keyword. Any other value will result in an error without modifying the current PIR rate.

Values

1 to 6400000000, max

cir-rate

Specifies the CIR rate for the scheduler. The cir parameter accepts a value in kb/s, or the max or sum keywords. Any other value will result in an error without modifying the current CIR rate.

If the cir is set to max, then the CIR rate is set to infinity, but is limited by the pir-rate.

If the cir is set to sum, then the CIR rate is set to the summed CIR values of the children schedulers, policers, or queues.

Values

0 to 6400000000, max, sum

Platforms

All

Context

[Tree] (config>app-assure>group>cflowd>volume rate)

Full Context

configure application-assurance group cflowd volume rate

Description

This command configures the sampling rate of packets for the cflowd export of application assurance volume statistics.

The no form of this command reverts to the default value.

Parameters

sample-rate

Specifies the rate at which to sample packets for the cflowd export of application assurance volume statistics.

Values

1 to 10000

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>app-assure>group>policer rate)

[Tree] (config>app-assure>group>tod-override rate)

Full Context

configure application-assurance group policer rate

configure application-assurance group policer tod-override rate

Description

This command configures the administrative PIR and CIR for bandwidth policers and flow setup rate limits for flow policers. The actual rate sustained by the flow can be limited by other policers that may be applied to that flow’s traffic. This command does not apply to flow-count-limit policers.

The cir option is applicable only to dual-bucket bandwidth policers. It is recommended to configure flow setup rate subscriber-level policer for AA subscribers to ensure fair usage of flow resources between AA subscribers.

The no form of this command resets the values to defaults.

Default

rate max cir 0

Parameters

pir-rate

Specifies an integer for the PIR rate in kb/s for bandwidth policers.

Values

1 to 100000000, max or flows/sec

cir-rate

Specifies an integer for the CIR rate in kb/s.

Values

0 to 100000000, max

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (debug>app-assure>group>port-recorder rate)

[Tree] (debug>app-assure>group>http-host-recorder rate)

Full Context

debug application-assurance group port-recorder rate

debug application-assurance group http-host-recorder rate

Description

This command configures the sampling rate for the recorded http host, a sampling rate of 10 will sample one out of 10 http-host.

Parameters

sample-rate

Specifies the sample rate.

Values

1 to 10000

Default

100

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Output

The following configuration records http-host entries ending with ".com” as a result of the expression filter configuration. It will not record any other HTTP host values since the default-filter-action set to no-record. The http-host entries analyzed by the recorder in the first place are http-host-app-filter-candidates.

7750# show debug                                             
debug
    application-assurance
        group 1:1
            http-host-recorder
                filter
                    default-filter-action no-record
                    expression 1 http-host eq "*.com$" record
                    record http-host-app-filter-candidates
                exit
                rate 100
                no shutdown
            exit
        exit
    exit
exit

Context

[Tree] (config>qos>plcr-ctrl-plcy>tier>arbiter rate)

Full Context

configure qos policer-control-policy tier arbiter rate

Description

This command is used to define the maximum bandwidth an instance of the arbiter can receive from its parent tier 1 arbiter or the root arbiter. The arbiter instance enforces this limit by calculating the bandwidth each of its child policers should receive relative to their offered loads, parenting parameters, and individual rate limits, and using that derived rate as a child PIR decrement rate override. The override will not exceed the child policer’s administrative rate limit and the aggregate of all the child PIR decrement rates will not exceed the specified arbiter rate limit.

The arbiter’s policy defined rate value may be overridden at the SAP or sub-profile where the policer-control-policy is applied. Specifying an override prevents the arbiter from being removed from the policer control policy until the override is removed.

The no form of this command is used to remove a rate limit from the arbiter at the policer control policy level. The policy level rate limit for the arbiter will return to the default value of max. The no rate command has no effect on instances of the arbiter where a rate limit override has been defined.

Default

rate max

Parameters

rate

Enter an integer representing the rate limit in kilobits per second.

Values

1 to 6400000000, max

max

When max is specified, the arbiter does not enforce a rate limit on its child policers or arbiters other than the individual rate limits enforced at the child level.

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>qos>sap-egress>policer rate)

[Tree] (config>qos>sap-ingress>policer rate)

Full Context

configure qos sap-egress policer rate

configure qos sap-ingress policer rate

Description

This command is used to configure the policer’s metering and optional profiling rates. The metering rate is used by the system to configure the policer’s PIR leaky bucket’s decrement rate while the profiling rate configures the policer’s CIR leaky bucket’s decrement rate. The decrement function empties the bucket while packets applied to the bucket attempt to fill it based on each packet’s size. If the bucket fills faster than how much is decremented per packet, the bucket’s depth eventually reaches its exceed (CIR) or violate (PIR) threshold. The cbs, mbs, and high-prio-only commands are used to configure the policer’s PIR and CIR thresholds.

If a packet arrives at the policer while the bucket’s depth is less than the threshold associated with the packet, the packet is considered to be conforming to the bucket’s rate. If the bucket depth is equal to or greater than the threshold, the packet is considered to be in the exception state. For the CIR bucket, the exception state is exceeding the CIR rate while the PIR bucket's exception state is violating the PIR bucket rate. If the packet is violating the PIR, the packet is marked red and will be discarded. If the packet is not red, it may be green or yellow, based on the conforming or exceeding state from the CIR bucket.

When a packet is red, neither the PIR nor CIR bucket depths are incremented by the packets size. When the packet is yellow, the PIR bucket is incremented by the packet size, but the CIR bucket is not. When the packet is green, both the PIR and CIR buckets are incremented by the packet size. This ensures that conforming packets impact the bucket depth while exceeding or violating packets do not.

The policer’s adaptation-rule command settings are used by the system to convert the specified rates into hardware timers and decrement values for the policer’s buckets.

By default, the policer’s metering rate is max and the profiling rate is 0 kb/s (all packets out-of-profile).

The rate settings defined for the policer in the QoS policy may be overridden on an sla-profile or SAP where the policy is applied.

The no form of this command is used to restore the default metering and profiling rate to a policer.

Parameters

{max | pir-rate}

Specifying the keyword max or an explicit pir-rate parameter directly following the rate command is required and identifies the policer’s metering rate for the PIR leaky bucket. When the policer is first created, the metering rate defaults to max. The pir-rate value must be expressed as an integer and defines the rate in kilobits-per-second. The integer value is multiplied by 1,000 to derive the actual rate in bits-per-second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

1 to 6400000000, max

cir {max | cir-rate}

The optional cir keyword is used to override the default CIR rate of the policer. Specifying the keyword max or an explicit cir-rate parameter directly following the cir keyword is required and identifies the policer’s profiling rate for the CIR leaky bucket. When the policer is first created, the profiling rate defaults to 0 kb/s. The cir-rate value must be expressed as an integer and defines the rate in kilobits-per-second. The integer value is multiplied by 1,000 to derive the actual rate in bits-per-second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

0 to 6400000000, max

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>qos>sap-ingress>queue rate)

Full Context

configure qos sap-ingress queue rate

Description

This command defines the administrative Peak Information Rate (PIR), the administrative Committed Information Rate (CIR), and the administrative Fair Information Rate (FIR) parameters for the queue.

The PIR defines the maximum rate that the queue can transmit packets through the switch fabric (for SAP ingress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. For SAP ingress, the CIR also defines the rate that packets are considered in-profile by the system, unless cir-non-profiling is configured. In-profile, then out-of-profile, packets are preferentially queued by the system at egress and at subsequent next-hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The FIR defines an additional rate at which the system prioritizes the queue over other queues competing for the same bandwidth above that used by the CIR.

The rate command can be executed at any time, altering the PIR, CIR, and FIR for all queues created through the association of the SAP ingress QoS policy with the queue-id.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0, 0).

Default

rate max cir 0 fir 0

Parameters

pir-rate

Defines the administrative PIR, in kilobits per second, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and the value must be given as a positive integer.

The actual PIR is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 6400000000, max

Default

max

cir-rate

The cir parameter overrides the default administrative CIR, in kilobits per second, used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and the value must be given as a positive integer. The actual CIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

0 to 6400000000, max

Default

0

fir-rate

The fir parameter overrides the default administrative FIR, in kilobits per second, used by the queue. When the rate command is executed, an FIR setting is optional. When the rate command has not been executed or the fir parameter is not explicitly specified, the default FIR (0) is assumed.

Fractional values are not allowed and the value must be given as a positive integer. The actual FIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

FIR is only supported on FP4 hardware and is ignored when the related policy is applied to FP2- or FP3-based hardware.

Values

0 to 6400000000, max

Default

0

police

Specifies that traffic feeding into the queue instance above the specified PIR rate will be dropped. When the police keyword is defined, only the PIR rate may be overridden.

Platforms

All

Context

[Tree] (config>qos>sap-egress>queue rate)

Full Context

configure qos sap-egress queue rate

Description

This command defines the administrative Peak Information Rate (PIR) and the administrative Committed Information Rate (CIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets out an egress interface (for SAP egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled as in- or out-of-profile throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR rates for all queues created through the association of the SAP egress QoS policy with the queue-id.

When configured on an egress HSQ queue group queue, the cir keyword is ignored.

This command is ignored for egress HSQ queue group queues which are attached to an HS WRR group within an associated HS attachment policy. In this case, the configuration of the rate is performed under the hs-wrr-group within the SAP egress QoS policy.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Default

rate max cir 0

Parameters

pir-rate

Defines the administrative PIR rate, in kilobits per second, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 6400000000, max

Default

max

cir-rate

The cir parameter overrides the default administrative CIR, in kilobits per second, used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be given as a positive integer.

Values

0 to 6400000000, max

Default

0

Platforms

All

Context

[Tree] (config>qos>network-queue>hs-wrr-group rate)

Full Context

configure qos network-queue hs-wrr-group rate

Description

This command specifies the scheduling rate applied to the HS WRR group as a percentage of the port rate, which includes both the egress-rate and HS scheduler policy max-rate, if configured.

The no form of the command reverts to the default.

Default

rate 100

Parameters

percent

Specifies the scheduling rate of the HS WRR group as a percentage.

Values

1 to 100

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>qos>sap-egress>hs-wrr-group rate)

Full Context

configure qos sap-egress hs-wrr-group rate

Description

This command specifies the scheduling rate applied to the HS WRR group in kb/s. Alternatively, the keyword max can be specified, which removes the bandwidth limitation on the HS WRR group. The rate and percent-rate commands are mutually exclusive.

The no form of the command reverts to the default value.

Default

rate max

Parameters

rate

Specifies the scheduling rate of the HS WRR group in kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>qos>qgrps>egr>qgrp>hs-wrr-group rate)

Full Context

configure qos queue-group-templates egress queue-group hs-wrr-group rate

Description

This command specifies the scheduling rate applied to the HS WRR group in kb/s. Alternatively, the keyword max can be specified, which removes the bandwidth limitation on the HS WRR group. The rate and percent-rate commands are mutually exclusive.

The no form of the command reverts to the rate max.

Default

rate max

Parameters

rate

Specifies the scheduling rates of the HS WRR group in kb/s.

Values

1 to 2000000000, max

Platforms

7750 SR-7/12/12e

Context

[Tree] (config>qos>network-queue>queue rate)

Full Context

configure qos network-queue queue rate

Description

This command defines the administrative Peak Information Rate (PIR), the administrative Committed Information Rate (CIR), and the administrative Fair Information Rate (FIR) parameters for the queue.

The PIR defines the percentage that the queue can transmit packets through the switch fabric (for ingress queues) or out of an egress port (for egress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available bandwidth.

The CIR defines the percentage at which the system prioritizes the queue over other queues competing for the same bandwidth.

The CIR can be used by the queue’s port-parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent port scheduler.

The FIR defines an additional percentage at which the system prioritizes the queue over other queues competing for the same bandwidth above that used by the CIR percentage.

The rate command can be executed at any time, altering the PIR, CIR, and FIR for all queues created through the association of the network queue policy with the queue-id.

When configured on an egress HSQ queue group queue, the cir keyword is ignored.

This command is ignored for egress HSQ queue group queues which are attached to an HS WRR group within an associated HS attachment policy. In this case, the configuration of the rate is performed under the hs-wrr-group within the network queue policy.

The no form of the command returns all queues created with the queue-id by association with the network queue policy to the default PIR, CIR, and FIR parameters.

Default

rate 100 cir 0 fir 0

Parameters

percent

Defines the percentage of the sum of the capacities of network and hybrid ports on that FP (taking into account any ingress-rate configuration) or egress port speed for the rate allowed for the queue. When the rate command is executed, a valid percent (PIR setting) must be explicitly defined. When the rate command has not been executed, the default PIR of 100 is assumed. Fractional values are not allowed, and the value must be given as a positive integer.

The actual PIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 100

Default

100

cir percent

Defines the percentage of the sum of the capacities of network and hybrid ports on that FP (taking into account any ingress-rate configuration) or egress port speed for the CIR allowed for the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed. Fractional values are not allowed, and the value must be given as a positive integer. The actual CIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

0 to 100

Default

0

fir percent

Defines the percentage of the sum of the capacities of network and hybrid ports on that FP (taking into account any ingress-rate configuration) or egress port speed for the FIR allowed for the queue. When the rate command is executed, a FIR setting is optional. When the rate command has not been executed or the fir parameter is not explicitly specified, the default FIR (0) is assumed. Fractional values are not allowed, and the value must be given as a positive integer. The actual FIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned. FIR is only supported on FP4 hardware and is ignored when the related policy is applied to FP2- or FP3-based hardware.

Values

0 to 100

Default

0

Platforms

All

Context

[Tree] (config>qos>qgrps>egr>qgrp>policer rate)

[Tree] (config>qos>qgrps>ing>qgrp>policer rate)

Full Context

configure qos queue-group-templates egress queue-group policer rate

configure qos queue-group-templates ingress queue-group policer rate

Description

This command is used to configure the policer’s metering and optional profiling rates. The metering rate is used by the system to configure the policer’s PIR leaky bucket’s decrement rate while the profiling rate configures the policer’s CIR leaky bucket’s decrement rate. The decrement function empties the bucket while packets applied to the bucket attempt to fill it based on each packet’s size. If the bucket fills faster than how much is decremented per packet, the bucket’s depth eventually reaches its exceed (CIR) or violate (PIR) threshold. The cbs, mbs, and high-prio-only commands are used to configure the policer’s PIR and CIR thresholds.

If a packet arrives at the policer while the bucket’s depth is less than the threshold associated with the packet, the packet is considered to be conforming to the bucket’s rate. If the bucket depth is equal to or greater than the threshold, the packet is considered to be in the exception state. For the CIR bucket, the exception state is exceeding the CIR rate while the PIR bucket's exception state is violating the PIR bucket rate. If the packet is violating the PIR, the packet is marked red and will be discarded. If the packet is not red, it may be green or yellow, based on the conforming or exceeding state from the CIR bucket.

When a packet is red, neither the PIR nor CIR bucket depths are incremented by the packets size. When the packet is yellow, the PIR bucket is incremented by the packet size, but the CIR bucket is not. When the packet is green, both the PIR and CIR buckets are incremented by the packet size. This ensures that conforming packets impact the bucket depth while exceeding or violating packets do not.

The policer’s adaptation-rule command settings are used by the system to convert the specified rates into hardware timers and decrement values for the policer’s buckets.

By default, the policer’s metering rate is max and the profiling rate is 0 kb/s (all packets out-of-profile).

The no form of this command is used to restore the default metering and profiling rate to a policer.

Parameters

{max | pir-rate}

Specifying the keyword max or an explicit pir-rate parameter directly following the rate command is required and identifies the policer’s metering rate for the PIR leaky bucket. When the policer is first created, the metering rate defaults to max. The pir-rate value must be expressed as an integer and defines the rate in kilobits-per-second. The integer value is multiplied by 1,000 to derive the actual rate in bits-per-second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the PIR used is equivalent to max.

Values

max, 1 to 2000000000

cir {max | cir-rate}

The optional cir keyword is used to override the default CIR rate of the policer. Specifying the keyword max or an explicit cir-rate parameter directly following the cir keyword is required and identifies the policer’s profiling rate for the CIR leaky bucket. When the policer is first created, the profiling rate defaults to 0 kb/s. The cir-rate value must be expressed as an integer and defines the rate in kilobits-per-second. The integer value is multiplied by 1,000 to derive the actual rate in bits-per-second. When max is specified, the maximum policer rate used will be equal to the maximum capacity of the card on which the policer is configured. If the policer rate is set to a value larger than the maximum rate possible for the card, then the CIR used is equivalent to max.

Values

max, 0 to 2000000000

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR

Context

[Tree] (config>qos>queue-group-templates>ingress>queue-group>queue rate)

Full Context

configure qos queue-group-templates ingress queue-group queue rate

Description

This command defines the administrative Peak Information Rate (PIR), the administrative Committed Information Rate (CIR), and the administrative Fair Information Rate (FIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the switch fabric (for SAP ingress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. For SAP ingress, the CIR also defines the rate that packets are considered in-profile by the system, unless cir-non-profiling is configured. In-profile, then out-of-profile, packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The FIR defines an additional rate at which the system prioritizes the queue over other queues competing for the same bandwidth above that used by the CIR.

The rate command can be executed at any time, altering the PIR, CIR, and FIR for all queues created through the association of the ingress queue group template with the queue-id.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR, CIR, and FIR parameters (max, 0, 0).

Default

rate max cir 0 fir 0

Parameters

pir-rate

Defines the administrative PIR, in kilobits, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed. Fractional values are not allowed and the value must be given as a positive integer.

The actual PIR is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 2000000000 kb/s, max

Default

max

cir-rate

The cir parameter overrides the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed. Fractional values are not allowed and the value must be given as a positive integer. The actual CIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 2000000000 kb/s, max

Default

0

fir-rate

The fir parameter overrides the default administrative FIR used by the queue. When the rate command is executed, an FIR setting is optional. When the rate command has not been executed or the fir parameter is not explicitly specified, the default FIR (0) is assumed.

Fractional values are not allowed and the value must be given as a positive integer. The actual FIR used is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

FIR is only supported on FP4 hardware and is ignored when the related policy is applied to FP2- or FP3-based hardware.

Values

1 to 2000000000 kb/s, max

Default

0

police

Specifies that traffic feeding into the queue instance above the specified rate is dropped.

Platforms

All

Context

[Tree] (config>qos>queue-group-templates>egress>queue-group>queue rate)

Full Context

configure qos queue-group-templates egress queue-group queue rate

Description

This command defines the administrative PIR and the administrative CIR parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets out an egress port. Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by oversubscription factors or available egress bandwidth.

The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. In-profile packets are preferentially queued by the system at egress and at subsequent next hop nodes where the packet can traverse. To be properly handled as in- or out-of-profile throughout the network, the packets must be marked accordingly for profiling at each hop.

The CIR can be used by the queue’s parent commands cir-level and cir-weight parameters to define the amount of bandwidth considered to be committed for the child queue during bandwidth allocation by the parent scheduler.

The rate command can be executed at any time, altering the PIR and CIR for all queues created through the association of the egress queue group template with the queue-id.

When configured on an egress HSQ queue group queue, the cir keyword is ignored.

This command is ignored for egress HSQ queue group queues which are attached to an HS WRR group within an associated HS attachment policy. In this case, the configuration of the rate is performed under the hs-wrr-group within the SAP egress QoS policy.

The no form of this command returns all queues created with the queue-id by association with the QoS policy to the default PIR and CIR parameters (max, 0).

Default

rate max cir 0

Parameters

pir-rate

Defines the administrative PIR rate, in kilobits, for the queue. When the rate command is executed, a valid PIR setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed.

Fractional values are not allowed and must be given as a positive integer.

The actual PIR rate is dependent on the queue’s adaptation-rule parameters and the actual hardware where the queue is provisioned.

Values

1 to 200000000 kb/s, max

Default

max

cir-rate

The cir parameter overrides the default administrative CIR used by the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed.

Fractional values are not allowed and must be given as a positive integer.

Values

0 to 200000000 kb/s, max

Default

0

Platforms

All

Context

[Tree] (config>qos>scheduler-policy>tier>scheduler rate)

Full Context

configure qos scheduler-policy tier scheduler rate

Description

The rate command defines the maximum bandwidth that the scheduler can offer its child queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the amount of bandwidth to be considered during the parent scheduler’s within-CIR distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler’s parent scheduler may not have the available bandwidth to meet the scheduler’s needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler will assume that an infinite amount of bandwidth is available and allow all child queues and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler's PIR and CIR parameters to the value configured in the applied scheduler policy.

Parameters

pir pir

Specifies the PIR rate of the scheduler in kb/s or it can be set to the maximum using the max keyword.

Values

1 to 6400000000, max

Default

max

cir cir

Specifies the CIR rate of the scheduler in kb/s or it can be set to the maximum using the max keyword. The sum keyword can also be used, which sets the CIR to the sum of child CIR values.

Values

0 to 6400000000, max, sum

Default

sum

Platforms

All

Context

[Tree] (config>qos>port-scheduler-policy>group rate)

Full Context

configure qos port-scheduler-policy group rate

Description

This command specifies the total bandwidth and the within-CIR bandwidth allocated to a weighted scheduler group.

The no form of this command returns the rate to its default value of max.

Parameters

pir-rate

Specifies PIR rates, in kilobits per second.

Values

1 to 6400000000, max

cir cir-rate

Specifies CIR rates, in kilobits per second.

Values

0 to 6400000000, max

Platforms

All

Context

[Tree] (config>qos>shared-queue>queue rate)

Full Context

configure qos shared-queue queue rate

Description

This command defines the administrative PIR, the administrative CIR, and the administrative FIR parameters for the queue.

The PIR defines the percentage that the queue can transmit packets through the switch fabric (for ingress queues). Defining a PIR does not necessarily guarantee that the queue can transmit at the intended rate. The actual rate sustained by the queue can be limited by over-subscription factors or available bandwidth.

The CIR defines the percentage at which the system prioritizes the queue over other queues competing for the same bandwidth.

The rate command can be executed at any time, altering the PIR, CIR, and FIR for the queue created with the queue-id.

Parameters

percent

Defines the percentage of the FP ingress capacity for the max rate allowed for the queue. When the rate command is executed, a valid percent (PIR) setting must be explicitly defined. When the rate command has not been executed, the default PIR of max is assumed. Fractional values are not allowed and the value must be given as a positive integer.

Values

1 to 100, max

Default

100

cir percent

Defines the percentage of the FP ingress capacity for the CIR allowed for the queue. When the rate command is executed, a CIR setting is optional. When the rate command has not been executed or the cir parameter is not explicitly specified, the default CIR (0) is assumed. Fractional values are not allowed and the value must be given as a positive integer.

Values

0 to 100, max

Default

0

fir percent

Defines the percentage of the FP ingress capacity for the FIR allowed for the queue. When the rate command is executed, a FIR setting is optional. When the rate command has not been executed or the fir parameter is not explicitly specified, the default FIR (0) is assumed. Fractional values are not allowed and the value must be given as a positive integer. FIR is only supported on FP4 hardware and is ignored when the related policy is applied to FP2- or FP3-based hardware.

Values

0 to 100

Default

0

Platforms

All

Context

[Tree] (config>cflowd rate)

Full Context

configure cflowd rate

Description

This command specifies the rate (N) at which traffic is sampled and sent for flow analysis. A packet is sampled every N packets; for example, when sample-rate is configured as 1, then all packets are sent to the cache. When sample-rate is configured as 100, then every 100th packet is sent to the cache.

The no form of this command resets the sample rate to the default value.

Default

rate 1000

Parameters

sample-rate

Specifies the rate at which traffic is sampled.

Values

1 to 10000

Platforms

All

Context

[Tree] (config>service>cust>multi-service-site>egress>agg-rate rate)

Full Context

configure service customer multi-service-site egress agg-rate rate

Description

This command defines the enforced aggregate rate for all queues associated with the agg-rate context. A rate must be specified for the agg-rate context to be considered to be active on the context’s object.

The no form of the command reverts to the default.

Parameters

kilobits-per-second

Specifies the rate limit for the multi-service site, in kilobits per second.

Values

1 to 6400000000, max

Platforms

All

Context

[Tree] (config>service>cust>multi-service-site>ingress>sched-override>scheduler rate)

[Tree] (config>service>cust>multi-service-site>egress>sched-override>scheduler rate)

Full Context

configure service customer multi-service-site ingress scheduler-override scheduler rate

configure service customer multi-service-site egress scheduler-override scheduler rate

Description

This command overrides specific attributes of the specified scheduler rate.

The rate command defines the maximum bandwidth that the scheduler can offer its child policers, queues or schedulers. The maximum rate is limited to the amount of bandwidth the scheduler can receive from its parent scheduler. If the scheduler has no parent, the maximum rate is assumed to be the amount available to the scheduler. When a parent is associated with the scheduler, the CIR parameter provides the scheduler’s amount of bandwidth to be considered during the parent schedulers 'within CIR’ distribution phase.

The actual operating rate of the scheduler is limited by bandwidth constraints other than its maximum rate. The scheduler’s parent scheduler may not have the available bandwidth to meet the scheduler’s needs or the bandwidth available to the parent scheduler could be allocated to other child schedulers or child policers or queues on the parent based on higher priority. The children of the scheduler may not need the maximum rate available to the scheduler due to insufficient offered load or limits to their own maximum rates.

When a scheduler is defined without specifying a rate, the default rate is max. If the scheduler is a root scheduler (no parent defined), the default maximum rate must be changed to an explicit value. Without this explicit value, the scheduler will assume that an infinite amount of bandwidth is available and allow all child queues and schedulers to operate at their maximum rates.

The no form of this command returns the scheduler’s to the PIR and CIR parameters to the value configured in the applied scheduler policy.

Parameters

pir-rate

Specifies the PIR rate.

Values

1 to 6400000000, max

Default

max

cir-rate

Specifies the CIR rate.

If the cir-rate is set to max, then the CIR rate is set to infinity. The sum keyword specifies that the CIR be used as the summed CIR values of the children schedulers, policers or queues.

Values

0 to 6400000000, max, sum

Default

sum

Platforms

All

Context

[Tree] (config>system>security>cpm-queue>queue rate)

Full Context

configure system security cpm-queue queue rate

Description

This command specifies the maximum bandwidth that will be made available to the queue in kilobits per second (kb/s).

Parameters

rate

Specifies the administrative Peak Information Rate (PIR) for the queue.

cir

Specifies the amount of bandwidth committed to the queue.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>sys>security>dist-cpu-protection>policy>local-monitoring-policer rate)

[Tree] (config>sys>security>dist-cpu-protection>policy>protocol>dynamic-parameters rate)

Full Context

configure system security dist-cpu-protection policy local-monitoring-policer rate

configure system security dist-cpu-protection policy protocol dynamic-parameters rate

Description

This command configures the rate and burst tolerance for the policer in either a packet rate or a bit rate.

The actual hardware may not be able to perfectly rate limit to the exact configured parameters. In this case, the configured parameters will be adapted to the closest supported rate. The actual (operational) parameters can be seen in CLI, for example, show service id 33 sap 1/1/3:33 dist-cpu-protection detail.

If the kilobits-per-second parameter value is configured as max, then the policer is effectively disabled (always conforming).

If the size parameter value is configured as 0, then all packets are considered as nonconforming.

Default

rate packets max within 1 initial-delay 0

Parameters

packets | kbps

specifies that the rate is either in units of packets per interval or in units of kilobits per second. The packets option would typically be used for lower rates (for example, for per-subscriber DHCP rate limiting) while the kbps option would typically be used for higher rates (for example, per-interface BGP rate limiting).

ppi

Specifies packets per interval.

Values

0 to 255, max

max = disable the policer (always conforming)

packets 0 = all packets considered nonconforming

seconds

Specifies the length of the ppi rate measurement interval.

Values

1 to 32767

packets

Specifies the number of packets allowed (even at line rate) in an initial burst (or a burst after the policer bucket has drained to zero) in addition to the normal ppi. This would typically be set to a value that is equal to the number of received packets in several full handshakes/negotiations of the particular protocol.

Values

0 to 255

kilobits-per-second

Specifies the kilobits per second.

Values

1 to 20000000, max

size

Specifies the tolerance for the kbps rate.

Values

0 to 4194304

Default

10

bytes | kilobytes

Specifies that the units of the mbs size parameter are either in bytes or kilobytes.

Platforms

All

Context

[Tree] (config>sys>security>dist-cpu-protection>policy>static-policer rate)

Full Context

configure system security dist-cpu-protection policy static-policer rate

Description

This command configures the rate and burst tolerance for the policer in either a packet rate or a bit rate.

The actual hardware may not be able to perfectly rate limit to the exact configured parameters. In this case, the configured parameters will be adapted to the closest supported rate. The actual (operational) parameters can be seen in CLI, for example, show service id 33 sap 1/1/3:33 dist-cpu-protection detail.

If the kilobits-per-second parameter value is configured as max, then the policer is effectively disabled (always conforming).

If the size parameter is configured as 0, then all packets are considered as nonconforming.

Default

rate packets max within 1 initial-delay 0

Parameters

packets | kbps

specifies that the rate is either in units of packets per interval or in units of kilobits per second. The packets option would typically be used for lower rates (for example, for per-subscriber DHCP rate limiting) while the kbps option would typically be used for higher rates (for example, per-interface BGP rate limiting).

ppi

Specifies packets per interval.

Values

0 to 8000, max

max = disable the policer (always conforming)

packets 0 = all packets considered nonconforming

seconds

Specifies the length of the ppi rate measurement interval.

Values

1 to 32767

packets

Specifies the number of packets allowed (even at line rate) in an initial burst (or a burst after the policer bucket has drained to zero) in addition to the normal ppi. This would typically be set to a value that is equal to the number of received packets in several full handshakes/negotiations of the particular protocol.

Values

0 to 255

kilobits-per-second

Specifies the kilobits per second.

Values

1 to 20000000, max

size

Specifies the tolerance for the kbps rate.

Values

0 to 4194304

Default

10

bytes | kilobytes

Specifies that the units of the mbs size parameter are either in bytes or kilobytes.

Platforms

All

Context

[Tree] (config>subscr-mgmt>ancp>policy>egress rate-adjustment)

[Tree] (config>subscr-mgmt>ancp>policy>ingress rate-adjustment)

Full Context

configure subscriber-mgmt ancp ancp-policy egress rate-adjustment

configure subscriber-mgmt ancp ancp-policy ingress rate-adjustment

Description

This command configures a rate adjustment for the scheduler. The rate-adjustment command should be used when the rate returned by the DSLAM is calculated with different encapsulation than the 7450 ESS or 7750 SR. The node will adjust the rate by the percent specified as:

DSLAM_RATE*adjust-rate/100 — rate-reduction.

The no form of this command reverts to the default.

Parameters

adjusted-percent

Specifies a rate adjustment for the scheduler.

Values

1 to 200

Default

100

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>card>virt-sched-adj rate-calc-min-int)

Full Context

configure card virtual-scheduler-adjustment rate-calc-min-int

Description

This command overrides the default minimum time that must elapse before a policer or queue’s offered rate may be recalculated. A minimum time between offered rate calculations is enforced to both prevent inaccurate estimation of the offered rate and excessive input to the virtual scheduler process.

In order to smooth out rapidly fluctuating offered rates, the system averages the measured offered rate with a window of previously measured offered traffic statistics and knowledge of the time between the samples.

The window size is defined by the "rate calculation minimum interval” with offered traffic statistics being read at most four times within the window. Any previous measured offered statistics within the window are used in the averaging function. Note that if there are large numbers of samples required, for example when a large number of queues are running HQoS, then it may be that a time greater than the "rate calculation minimum interval” passes before another sample of the offered statistics can be taken for a queue. In this case, in order to calculate an offered rate, HQoS will always use two samples, the current and the previous. In this case, using a smaller rate-calc-min-int will have no effect on the responsiveness of HQoS to queue rate changes.

The system separates policers and queues into fast and slow categories and maintains a separate "rate calculation minimum interval” for each type. The default for each type are as follows:

Slow Queue: 1.0 seconds

Fast Queue: 0.25 seconds

The actual minimum rate calculation interval may be increased or decreased by using the fast-queue and/or slow-queue keywords (which are also applicable for policers managed by HQoS) followed by a percent value which is applied to the default interval. The default slow-queue threshold rate is 1 Mb/s. Once a policer or queue is categorized as slow, its rate must rise to 1.5 Mb/s before being categorized as a fast policer or queue. The categorization threshold may be modified by using the slow-queue-threshold command.

The no form of this command restores the default fast queue and slow queue minimum rate calculation interval.

Default

no rate-calc-min-int

Parameters

percent-of-default

Specifies that the fast-queue percent-of-default parameter is optional and is used to modify the default minimum rate calculation time for "fast” queues. Defining 100.00 percent is equivalent to removing the override (restoring the default) on the fast queue minimum rate calculation time.

Values

0.01% to 1000.00%

Default

100.00%

percent-of-default

Specifies that the slow-queue percent-of-default parameter is optional and is used to modify the default minimum rate calculation time for "slow” queues. Defining 100.00 percent is equivalent to removing the override (restoring the default) on the slow queue minimum rate calculation time.

Values

0.01% to 1000.00%

Default

100.00%

Platforms

All

Context

[Tree] (config>subscr-mgmt>loc-user-db>ppp>host>access-loop-encapsulation rate-down)

Full Context

configure subscriber-mgmt local-user-db ppp host access-loop-encapsulation rate-down

Description

This command is applicable to LAC and LNS. It provides the last mile link rate in the downstream direction that is needed for proper shaping and calculating the interleaving delay.

The rate information in the last mile will be taken from the following sources in the order of priority:

• Statically provisioned value in local user database (LUDB).

• RADIUS.

• PPPoE tags on LAC or ICRQ message (RFC 5515) /ICCN message (TX Connect Seed) on LNS.

Default

no rate-down

Parameters

rate

Specifies the last mile link downstream rate in the access loop

Values

1 to 100000 kb/s

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s

Context

[Tree] (config>service>nat>syslog>syslog-export-policy rate-limit)

Full Context

configure service nat syslog syslog-export-policy rate-limit

Description

This command configures the maximum rate limit at which syslog messages are sent. Once the rate limit is exceeded, NAT flow logs will be buffered. Overload condition is characterized by exhaustion of this buffer space. This condition can occur due to imposed rate limit or the software speed limit. Once the buffer space is exhausted, new flow creation will be denied, and the teardown of the existing flows will be delayed until the buffer space becomes available.

The no form of the command removes the maximum rate limit from the configuration.

Parameters

packets-per-second

Specifies the packet rate limit in seconds.

Values

10 to 2147483647

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>filter>ip-filter>entry>action rate-limit)

Full Context

configure filter ip-filter entry action rate-limit

Description

This command configures the rate limit value for traffic matching this filter entry. Rate limit policers are configured with MBS equals CBS equals 10 ms of the rate and high-prio-only equals 0.

Traffic can also be rate limited based on extracted-traffic, packet-length, packet-length range, ttl, ttl range, or a pattern of conditional match criteria.

Packets that match the filter entry match criteria, but do not match the conditional match criteria value, are implicitly forwarded with no further match in the following filter entries.

For pattern match:

• the expression is left-aligned for the odd number bytes, for example, the expression 0xABC is programmed 0x0ABC in the line card

• the 'data' offset requires protocol UDP or TCP to be selected in the filter entry match criteria.

Parameters

value

Specifies the rate-limit value in kb/s (default) or packets per second (pps). A rate of 0 results in all traffic being dropped. A rate of max results in all traffic being forwarded.

Values

0 to 2000000000 kb/s, max

0 to 100000000 pps, max

extracted-traffic

Specifies rate-limit packets both extracted to the CPM and matching the filter entry match criteria.

packet-length

Specifies rate-limit packets matching both the filter entry match criteria and the packet-length value defined in the rate-limit action statement. Packets matching the filter entry match criteria and not matching the packet-length value, as defined in the rate-limit action statement, are implicitly forwarded with no further match in the following filter entries.

Values

lt — Specifies "less than”. The lt parameter cannot be used with the lowest possible numerical value for the parameter.

gt — Specifies "greater than”. The gt parameter cannot be used with the highest possible numerical value for the parameter.

eq — Specifies "equal to”.

packet-length-value

Specifies the packet length value for the rate limit action.

Values

0 to 65535

range

Specifies an inclusive range. When range is used, the start of the range (the first value entered) must be smaller than the end of the range (the second value entered).

expression

Specifies the hexadecimal pattern to match; up to eight bytes.

Values

0x0000000000000001 to 0xffffffffffffffff

mask

Specifies the mask for the pattern expression, up to eight bytes.

Values

0x0000000000000001 to 0xffffffffffffffff

offset-type

Specifies the starting point reference for the offset-value of this pattern.

Values

layer-3, layer-4, data, dns-qtype

offset-value

Specifies the offset value for the pattern expression. Dns-qtype supports offset value of 0.

Values

0 to 255

ttl-value

Specifies rate-limit packets matching both the filter entry match criteria and the TTL value defined in the rate-limit action statement. Packets matching the filter entry match criteria and not matching the TTL value, as defined in the rate-limit action statement, are implicitly forwarded with no further match in the following filter entries.

Values

0 to 255

Platforms

All

Context

[Tree] (config>filter>mac-filter>entry>action rate-limit)

Full Context

configure filter mac-filter entry action rate-limit

Description

This command sets the rate limit for the traffic matching both the filter entry match criteria and the packet-length-value defined in the rate-limit action statement.

Packets matching the filter entry match criteria and not matching the packet-length-value defined in the rate-limit action statement are implicitly forwarded with no further match in subsequent filter entries.

Rate limit packets matching both the filter entry match criteria and the ttl-value are defined in the action rate-limit statement.

Packets matching the filter entry match criteria and not matching the ttl-value defined in the rate-limit action statement are implicitly forwarded with no further match in the following filter entries.

Parameters

value

Specifies the rate-limit value in kb/s. A rate of 0 results in all traffic being dropped. A rate of max results in all traffic being forwarded.

Values

0 to 2000000000 kb/s | max

Platforms

All

Context

[Tree] (config>filter>ipv6-filter>entry>action rate-limit)

Full Context

configure filter ipv6-filter entry action rate-limit

Description

This command configures the rate limit value for traffic matching this filter entry.

Traffic can also be rate-limited based on extracted-traffic, payload-length, payload-length range, hop-limit, hop-limit range, or a pattern of conditional match criteria.

Packets that match the filter entry match criteria, but do not match the conditional match criteria value, are implicitly forwarded with no further match in the following filter entries.

For pattern match:

• the expression is left-aligned for the odd number bytes, for example, the expression 0xABC is programmed 0x0ABC in the line card.

• the 'data' offset requires protocol UDP or TCP to be selected in the filter entry match criteria.

Parameters

value

Specifies the rate-limit value in kb/s (default) or packets per second (pps). A rate of 0 results in all traffic being dropped. A rate of max results in all traffic being forwarded.

Values

0 to 2000000000 kb/s, max

0 to 100000000 pps, max

extracted-traffic

Specifies packets extracted to the CPM.

hop-limit

Specifies the hop limit value for the rate limit action.

Values

lt — Specifies "less than”. The lt parameter cannot be used with the lowest possible numerical value for the parameter.

gt — Specifies "greater than”. The gt parameter cannot be used with the highest possible numerical value for the parameter.

eq — Specifies "equal to”.

hop-limit-value

Specifies the hop limit value for the rate limit action.

Values

0 to 255

range

Specifies an inclusive range. When the range parameter is used, the start of the range (the first value entered) must be smaller than the end of the range (the second value entered).

expression

Specifies the hexadecimal pattern to match; up to eight bytes.

Values

0x0000000000000001 to 0xffffffffffffffff

mask

Specifies the mask for the pattern expression, up to eight bytes.

Values

0x0000000000000001 to 0xffffffffffffffff

offset-type

Specifies the starting point reference for the offset-value of this pattern.

Values

layer-3, layer-4, data, dns-qtype

offset-value

Specifies the offset value for the pattern expression. Dns-qtype supports offset value of 0.

Values

0 to 255

payload-length

Specifies rate-limit packets matching both the filter entry match criteria and the payload-length-value defined in the rate-limit action statement. Packets matching the filter entry match criteria and not matching the payload-length-value, as defined in the rate-limit action statement, are implicitly forwarded with no further match in the following filter entries.

Values

lt — Specifies "less than”. The lt parameter cannot be used with the lowest possible numerical value for the parameter.

gt — Specifies "greater than”. The gt parameter cannot be used with the highest possible numerical value for the parameter.

eq — Specifies "equal to”.

payload-length-value

Specifies the payload length value for the rate limit action.

Values

0 to 65535

Platforms

All

Context

[Tree] (config>subscr-mgmt>ancp>policy>ingress rate-modify)

[Tree] (config>subscr-mgmt>ancp>policy>egress rate-modify)

Full Context

configure subscriber-mgmt ancp ancp-policy ingress rate-modify

configure subscriber-mgmt ancp ancp-policy egress rate-modify

Description

This command configures rate modify scheduler parameters.

The no form of this command removes the scheduler name from the configuration.

Parameters

agg-rate-limit

Specifies that the maximum total rate for all subscriber egress queues for each subscriber associated with the policy.

scheduler-name

Specifies a scheduler name, up to 32 characters.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>ancp>policy>egress rate-monitor)

[Tree] (config>subscr-mgmt>ancp>policy>ingress rate-monitor)

Full Context

configure subscriber-mgmt ancp ancp-policy egress rate-monitor

configure subscriber-mgmt ancp ancp-policy ingress rate-monitor

Description

This command configures the rate monitor level.

The no form of this command removes the value from the configuration.

Parameters

kilobit-per-second

Specifies the rate below which the system generates an event.

Values

0 to 4294967295

alarm

When the monitored rate is below the configured value the system generates an alarm (trap) to the management system. The trap includes the rate as well as the ANCP policy name and the ANCP string.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>app-assure>group>policer rate-percentage)

Full Context

configure application-assurance group policer rate-percentage

Description

This command indirectly configures the rate used by Access-Network-Location (ANL) policers. Because ANL total bandwidth is dynamically measured and estimated by AA, this command allows the operator to configure the ratio of that measured bandwidth to be used by the ANL policer as the policer rate.

The no form of this command resets the values to defaults.

Default

no rate-percentage

Parameters

rate-percentage

Specifies an integer value that specifies a percentage that is applied against the ANL estimate maximum bandwidth to produce the actual rate that is used by the policer when ANL congestion occurs.

Values

0 to 200 (0: means drop all traffic)

Default

0

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>app-assure>group>policer rate-percentage-stage2)

Full Context

configure application-assurance group policer rate-percentage-stage2

Description

This command indirectly configures the rate used by Access-Network-Location (ANL) policers. Because ANL stage2 total bandwidth is dynamically measured and estimated by AA, this command allows the operator to configure the ratio of that measured bandwidth to be used by the ANL stage2 policer as the policer rate.

The no form of this command reverts to the default.

Parameters

rate-percentage

Specifies an integer value that specifies a percentage that is applied to the ANL estimated maximum bandwidth to produce the actual rate that is used by the policer when ANL stage2 congestion occurs. A value of 0 means that all traffic is dropped.

Values

0 to 200

Default

0

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>ancp>policy>egress rate-reduction)

[Tree] (config>subscr-mgmt>ancp>policy>ingress rate-reduction)

Full Context

configure subscriber-mgmt ancp ancp-policy egress rate-reduction

configure subscriber-mgmt ancp ancp-policy ingress rate-reduction

Description

This command defines a constant rate reduction to the rate specified by the DSLAM. The rate-reduction command should be used if the node should adjust the rate to a value that is offset (for example by a fixed multicast dedicated bandwidth) compared to the total available on the DSLAM.

When set, the rate is:

DSLAM_RATE*adjust-rate/100 — rate-reduction

The no form of this command removes the value from the configuration.

Parameters

kilobits-per-second

Specifies the rate reduction to be applied for this subscriber.

Values

0 to 4294967295

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>sla-profile>egress>bonding-selection rate-thresholds)

Full Context

configure subscriber-mgmt sla-profile egress bonding-selection rate-thresholds

Description

This command configures the rate thresholds that are required before decreasing or increasing the preferred link’s weight with the specified change percentage.

The low threshold value must be lower than the high threshold value.

The no form of this command reverts to the default.

Default

rate-thresholds high 90 low 80

Parameters

high-percentage

Specifies the high threshold, as a percentage of the reference rate.

Values

56 to 99

low-percentage

Specifies the low threshold, as a percentage of the reference rate.

Values

55 to 98

Platforms

7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>subscr-mgmt>cat-map>category rating-group)

Full Context

configure subscriber-mgmt category-map category rating-group

Description

This command configures the rating group applicable for this category.

The no form of this command reverts to the default.

Parameters

rating-group-id

Specifies the rating group applicable for this category.

Values

0 to 4294967295

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>cflowd>collector>aggregation raw)

Full Context

configure cflowd collector aggregation raw

Description

This command configures raw (unaggregated) flow data to be sent in Version 5.

The no form of this command removes this type of aggregation from the collector configuration.

Platforms

All

Context

[Tree] (file rd)

Full Context

file rd

Description

If the directory is empty, the rd command is used to remove it. The force option executes the command without prompting the user to confirm the action.

If the directory contains files and/or subdirectories, the rf parameter must be used to remove the directory.

Example:

A:nE1>file cf1:\ # rd test 
Are you sure (y/n)? y 
Deleting directory cf1:\test ..MINOR: CLI Cannot delete cf1:\test.
A:nE1>file cf1:\ # rd test force 
Deleting directory cf1:\test .MINOR: CLI Cannot delete cf1:\test.


A:nE1>file cf1:\ # rd testbase rf 
Deleting all subdirectories and files in specified directory. y/n ?y 
Deleting directory cf1:\testbase\testbase1 ..OK
Deleting directory cf1:\test .OK

Parameters

file-url

Specifies the directory to be removed.

Values

local-url	[cflash-id/][file-path] up to 200 characters, including cflash-id directory length up to 99 each
remote-url	[{ftp:// | tftp://}login:pswd@remote-locn/][file-path]
	up to 247 characters
	directory length up to 99 characters each
remote-locn	[hostname | ipv4-address | [ipv6-address]]
ipv4-address	a.b.c.d
ipv6-address	x:x:x:x:x:x:x:x[-interface]
	x:x:x:x:x:x:d.d.d.d[-interface]
	x - [0 to FFFF]H
	d - [0 to 255]D
	interface - up to 32 characters, for link local addresses 255
cflash-id	cf1:, cf1-A:, cf1-B:, cf2:, cf2-A:, cf2-B:, cf3:, cf3-A:, cf3-B:

rf

Forces a recursive delete.

force

Forces an immediate deletion of the specified directory. The rd file-url force command executes the command without displaying a user prompt message.

Platforms

All

Context

[Tree] (config>port>aps rdi-alarms)

Full Context

configure port aps rdi-alarms

Description

This command configures how RDI alarms (line, path, section) are generated on physical circuits of an APS ports. The command configuration changes are supported only for switching-mode set to uni_1plus1. The configuration can be changed only when no working and protecting circuit has been added. Options:

• circuit–RDI alarms are H/W-generated independently on each working and protect circuit based on RX failure of that circuit regardless of APS line status.

• suppress–RDI H/W generation on working and protect circuits is suppressed. No alarms are generated on RX failure of that circuit.

Default

rdi-alarms circuit

Platforms

7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e

Context

[Tree] (config>service>ies>sub-if>grp-if>ipv6 rdnss-lifetime)

[Tree] (config>service>ies>sub-if>ipv6>rtr-adv rdnss-lifetime)

[Tree] (config>subscr-mgmt>rtr-adv-plcy>dns-opt rdnss-lifetime)

[Tree] (config>service>vprn>sub-if>ipv6>rtr-adv rdnss-lifetime)

[Tree] (config>service>vprn>sub-if>grp-if>ipv6 rdnss-lifetime)

Full Context

configure service ies subscriber-interface group-interface ipv6 rdnss-lifetime

configure service ies subscriber-interface ipv6 rtr-adv rdnss-lifetime

configure subscriber-mgmt router-advertisement-policy dns-options rdnss-lifetime

configure service vprn subscriber-interface ipv6 rtr-adv rdnss-lifetime

configure service vprn subscriber-interface group-interface ipv6 rdnss-lifetime

Description

This command configures the maximum time that the RDNSS address may be used for name resolution.

The no form of this command returns the command to the default setting.

Default

rdnss-lifetime 3600

Parameters

seconds

Specifies the time, in seconds, that the RDNSS address is valid for this route.

Values

900 to 3600

infinite

Specifies that the RDNSS address can be used permanently.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>ies>sub-if>ipv6>rtr-adv>dns-opt rdnss-lifetime)

[Tree] (config>service>ies>sub-if>grp-if>ipv6>rtr-adv>dns-opt rdnss-lifetime)

[Tree] (config>service>vprn>sub-if>grp-if>ipv6>rtr-adv>dns-opt rdnss-lifetime)

[Tree] (config>service>vprn>sub-if>ipv6>rtr-adv>dns-opt rdnss-lifetime)

Full Context

configure service ies subscriber-interface ipv6 router-advertisements dns-options rdnss-lifetime

configure service ies subscriber-interface group-interface ipv6 router-advertisements dns-options rdnss-lifetime

configure service vprn subscriber-interface group-interface ipv6 router-advertisements dns-options rdnss-lifetime

configure service vprn subscriber-interface ipv6 router-advertisements dns-options rdnss-lifetime