Getting started

About this guide

This guide describes routing protocols including multicast, RIP, OSPF, IS-IS, BGP, and route policies provided by the router and presents configuration and implementation examples.

This document is organized into functional chapters and provides concepts and descriptions of the implementation flow, as well as Command Line Interface (CLI) syntax and command usage.

Note: Unless otherwise indicated, this guide uses classic CLI command syntax and configuration examples.

The topics and commands described in this document apply to the:

  • 7450 ESS

  • 7750 SR

  • 7950 XRS

  • Virtualized Service Router (VSR)

For a list of unsupported features by platform and chassis, see the SR OS R22.x.Rx Software Release Notes, part number 3HE 18412 000 x TQZZA.

Command outputs shown in this guide are examples only; actual displays may differ depending on supported functionality and user configuration.

Note: The SR OS CLI trees and command descriptions can be found in the following guides:

  • 7450 ESS, 7750 SR, 7950 XRS, and VSR Classic CLI Command Reference Guide

  • 7450 ESS, 7750 SR, 7950 XRS, and VSR Clear, Monitor, Show, and Tools Command Reference Guide (for both MD-CLI and Classic CLI)

  • 7450 ESS, 7750 SR, 7950 XRS, and VSR MD-CLI Command Reference Guide

Note: Content previously found in this guide related to Segment Routing and PCE has been moved to the 7750 SR and 7950 XRS Segment Routing and PCE User Guide .
Note: This guide generically covers Release 22.x.Rx content and may contain some content that will be released in later maintenance loads. See the SR OS R22.x.Rx Software Release Notes, part number 3HE 18412 000 x TQZZA, for information about features supported in each load of the Release 22.x.Rx software.

Router configuration process

Configuration process lists the tasks necessary to configure RIP, OSPF, IS-IS, and BGP protocols, and route policies on the 7450 ESS, 7750 SR, and 7950 XRS. This guide is presented in an overall logical configuration flow. Each section describes a software area and provides CLI syntax and command usage to configure parameters for a functional area.

Table 1. Configuration process
Area Task Section

RIP configuration

Configure RIP

Configuring RIP with CLI

RIP configuration management

RIP configuration management tasks

OSPF configuration

Configure an LFA SPF policy

Loop-free alternate shortest path first policies

Configure OSPF

Configuring OSPF with CLI

OSPF configuration management

OSPF configuration management tasks

IS-IS configuration

Configure IS-IS

Configuring IS-IS with CLI

Configure IS-IS components

Configuring IS-IS components

IS-IS configuration management

IS-IS configuration management tasks

BGP configuration

Configure BGP

Configuring BGP with CLI

BGP configuration management

BGP configuration management tasks

Route Policies

Configure route policies

Configuring route policies with CLI

Configure route policy components

Configuring route policy components

Route policy configuration management

Route policy configuration management tasks

Conventions

This section describes the general conventions used in this guide.

Precautionary and information messages

The following are information symbols used in the documentation.

DANGER: Danger warns that the described activity or situation may result in serious personal injury or death. An electric shock hazard could exist. Before you begin work on this equipment, be aware of hazards involving electrical circuitry, be familiar with networking environments, and implement accident prevention procedures.
WARNING: Warning indicates that the described activity or situation may, or will, cause equipment damage, serious performance problems, or loss of data.
Caution: Caution indicates that the described activity or situation may reduce your component or system performance.
Note: Note provides additional operational information.
Tip: Tip provides suggestions for use or best practices.

Options or substeps in procedures and sequential workflows

Options in a procedure or a sequential workflow are indicated by a bulleted list. In the following example, at step 1, the user must perform the described action. At step 2, the user must perform one of the listed options to complete the step.

Options in a procedure

  1. User must perform this step.
  2. This step offers three options. User must perform one option to complete this step.
    • This is one option.
    • This is another option.
    • This is yet another option.

Substeps in a procedure or a sequential workflow are indicated by letters. In the following example, at step 1, the user must perform the described action. At step 2, the user must perform two substeps (a. and b.) to complete the step.

Substeps in a procedure

  1. User must perform this step.
  2. User must perform all substeps to complete this action.
    1. This is one substep.
    2. This is another substep.