Video services

Video services

Video groups

Video services are supported on:

  • MS-ISA

  • MS-ISA2

  • MS-ISM (two MS-ISA2 on a single line card)

  • ESA

These MS-ISA and ESA variants are referred to as ISAs in this section.

Both MS-ISA and MS-ISA2 support FCC and RET, VQM, and perfect stream functionality. The ESA currently only supports FCC, RET, and perfect stream . Perfect stream is only supported on multi-complex platforms.

When configured in the router, ISAs are logically grouped into video groups for video services. A video group allows multiple ISAs/ESAs for an application. The system performs load balancing between the ISAs. Nokia recommends not mixing ISA, ISA2, and ESA in the same video group. All ISAs within a video group are always active, there are no standby ISAs.

Video groups provide a redundancy mechanism to guard against hardware failure within a group where the system automatically rebalances tasks to the group excluding the failed MS-ISA or ESA-VM. Video groups also pool the processing capacity of all the group members and increase the application throughput because of the increased packet processing capability of the group. The buffer usage is typically identical for all members of the video group, so increasing the number of members in a group does not increase the scaling numbers for parameters bounded by available buffering, but there is still the increase in performance gained from the pooled packet processor capacity. A video service must be enabled at the video group level before that service can be used.

A video application may restrict the number of ISAs supported in a video group to a smaller number. Please contact your local Nokia representative for more information about video application specifications.

Note: There are restrictions to the number of MS-ISA and ESA-VMs that can be added to a video group. MS-ISA and ESA-VMs must not intermix within a video group. Only the SR-7/12/12e platforms require video groups to be in separate forwarding complexes. For more information, contact your local Nokia representative.

Video SAP

The video group logically interfaces to a service instance with a video Service Access Point (SAP). Like a SAP for connectivity services, the video SAP allows the assignment of an ingress and egress filter policy and QoS policy.

Ingress and egress directions for the filter and QoS policy are named based on the perspective of the router which is the opposite perspective of the ISA. An ‟egress” policy is one that applies to traffic egressing the router and ingressing the ISA. An ‟ingress” policy is one that applies to traffic ingressing the router and egressing the video. Although potentially confusing, the labeling of ingress and egress for the ISA policies was chosen so that existing policies for connectivity services can be reused on the ISA unchanged.

If no filter or QoS policy is configured, the default policies are used.

One of the key attributes of a video SAP is a video group association. The video SAP’s video group assignment is what determines which video group services on that video SAP. The video groups configuration determines what video services are available.

Video interface

The video interface acts as the following:

  • FCC and RET server

  • interface for multicast buffering

  • interface for the perfect stream

A video interface supports up to 16 IP addresses and is supported on VPRN or IES services.

Video interface properties

The video application is supported on various platforms but the video interface has different characteristics on the following platforms:

  • 7750 SR-7, 7750 SR-12, 7750 SR-12e

    For 7750 SR-7, 7750 SR-12, 7750 SR-12e, the video interface is a logical interface regardless of whether ISA or ESA is used. For these platforms, the video interface uses direct protocol as the routing policy to export to IGP or BGP protocols. Use the following command to configure the routing policy for a video interface as direct protocol:

    • MD-CLI

      configure policy-options policy-statement entry from protocol name direct
    • classic CLI

      configure router policy-options policy-statement entry from protocol direct
  • All other platforms supporting video applications

    The video interface is modeled as a route. Only ESA is supported on these platforms. For these platforms, the video interface uses video protocol as the routing policy to export to IGP or BGP protocols. Use the following command to configure the routing policy for a video interface as video protocol:

    • MD-CLI

      configure policy-options policy-statement entry from protocol name video
    • classic CLI

      configure router policy-options policy-statement from protocol video

Multicast information policies

Multicast information policies on the 7750 SR and 7450 ESS serve multiple purposes. In the context of a service with video services, the multicast information policy assigned to the service provides configuration information for the multicast channels and defines video policy elements for a video interface.

This section describes the base elements of a multicast information policy in support of a video service. Specific video service features require additional configuration in the multicast information policy, which is described in the sections dedicated to the video feature.

Multicast information policies are named hierarchically structured policies that are composed of channel bundles that contain channels containing source-overrides.

  • A bundle has an assigned name and contains a collection of channels. If attributes are not defined for a bundle they are inherited from a special default bundle named ‟default”. Use commands in the following context to configure bundles for the multicast information policy:

    • MD-CLI
      configure multicast-management multicast-info-policy bundle
    • classic CLI
      configure mcast-management multicast-info-policy bundle
  • Channels are ranges of IP multicast addresses identified by a start IP multicast address (GGstart) and optional end IP multicast address (Gend), so the channels encompass (*,Gstart) through (*,Gend). A channel attribute is inherited from its bundle unless the attribute is explicitly assigned, in which case the channel attribute takes precedence.

  • Source overrides within a channel are IP multicast addresses within the channel that have a specific source IP address (Soverride), so the source override encompasses (Soverride,Gstart) through (Soverride,Gend). A source-override attribute is inherited from its channel, unless the attribute is explicitly assigned in the source-override channel, in which case the source-override channel attribute takes precedence.

For an IP multicast channel (*,G) or (S,G), the most specific policy element in the hierarchy that matches applies to that channel.

A multicast information policy is assigned to a service instance. For video services, the multicast information policy assigned to the service determines the video group for a given IP multicast channel. When a channel is assigned to a video group, the channel is sent to the video group for buffering or processing as appropriate depending on the video services enabled on the video group. If no video group is assigned to a channel, the channel is still distributed within the service instance, but no video services are available for that channel.

In addition to bundles, channels, and source-overrides, multicast information policies also include video policies. Video policies define attributes for the video interfaces within the service instance.

Video policy attributes are specific to the video feature and are covered in detail in the applicable video feature section. Video policies are mentioned here because they are an element of the multicast information policy and provide the link to configuration for a video interface.

Perfect stream protection

To protect against network interruption or reconvergence, it is often more efficient to protect the stream using an alternate transmission path. This can be a separate physical interface, transmission link, system, or even technology.

Perfect stream is also known as duplicate stream in some markets. Perfect stream protection allows an operator to split a single multicast stream (single S,G and common SSRC) into two different transmission paths that may have different transmission characteristics, such as latency or jitter. Instead of selecting one stream for retransmission to the client, the perfect stream protection feature evaluates each stream packet-by-packet, selecting the first, valid packet for retransmission.

A circular buffer is used for perfect stream protection which incorporates both packet-by-packet selection (based on RTP sequence number/timestamp and SSRC) and a re-ordering function whereby any out-of-sequence packets are placed into the buffer in order, therefore creating a corrected, in-order stream.

Playout rate is a function in ingest rate, however because the two streams may be delayed between one-another a few assumptions are made:

  • The first arriving packet is always put into the buffer, allowing for the backup medium to wander in terms of latency and jitter.

  • Because the source is the same, the rate at which a packet is put into the buffer (from either stream) can be assumed to be the normal bitrate.

The output RTP stream is always maintained in-sequence and the playout speed is always controlled. A moving window calculated against the time stamp smooths jitter that may occur between packets or the two contributing streams. The playout stream is described in Perfect stream selection.

Perfect stream selection

This section describes perfect stream protection and provides details about packet selection on playout.

Stream identification

Stream selection is a simple selection algorithm that is applicable to any number of input streams. It is a prerequisite for stream selection that RTPv2 encapsulation be used in UDP.

Each service is identified by multicast source, group/destination address and current synchronization source (SSRC). After the service has been identified, the ISA monitors its ingress for:

  • traffic with a DA of the multicast group

  • traffic with a DA of the ISA (unicast)

Traffic is further checked as having RTP-in-UDP payload, RTP version 2.

The SSRC of each incoming RTP packet is learned as a unique source. Only one SSRC is supported for each stream; as SSRC may change during abnormal situations (such as encoder failover), it can be updated.

An SSRC can only be updated when a Loss of Transport (LoT) occurs, as other perfect streams (with the original SSRC) may still be operational. When an LoT occurs, the SSRC is deleted, the buffers are purged, and the RTP sequence counters are reset. The SSRC is extracted from the next valid RTP packet and the sequence starts over.

One RTP packet from the perfect stream is selected for insertion into the video ISA buffer. After a packet is selected, the RTP sequence counter is incremented and any further RTP packets received by the ISA with the previous sequence number are discarded.

In summary, perfect stream selection is a FIFO algorithm for RTP packet selection; this is considered optimal because:

  • All stream sources are identical. Therefore, for any sequence number, the payload should also be identical.

  • Most bit errors should be detected by the CRC-32 algorithm applied to Ethernet, SDH, and so on.

    These devices typically discard frames where bit errors occur, with the net result being that the video ISA receives a bit error-free stream (though packet loss can occur).

  • The UDP checksum is verified by the video ISA (after input VQM) and any failures result in a silent discard of the packet.

  • VQM can be used in conjunction with perfect stream protection.

    VQM can be used to monitor the quality of two duplicate ingress multicast streams and the egress multicast stream (after perfect stream selection). This is particularly useful to compare between the ingress and egress multicast. Monitoring the egress multicast after perfect stream selection can provide an insight to the customer viewing experience.

Initial sequence identification

When a service is defined and is administratively enabled, the video ISA monitors for valid RTP packets and on first receipt of a valid RTP packet learn the following information:

  • SSRC

  • sequence number

  • timestamp (as timestamp is profile-specific, MPEG2-TS are assumed)

The packet is inserted into the video ISA playout buffer associated with that particular service and playout when directed (playout algorithm).

Packet selection

Each valid RTP packet received for a specific service is inserted into the buffer if there is no existing RTP packet that matches the sequence number. When sequence numbers and timestamps discontinue, the video ISA makes a limited attempt to validate the MPEG stream. The video ISA code adopts a philosophy to ensure that sequence numbers and timestamps increment correctly. If packets are non-contiguous, the packet selection algorithm adapts.

Duplicate packets are detected by sequence number or timestamp, unless M-bit resets the timestamp. A packet that is already in the buffer and which has the same sequence number as a received packet (or one recently played out) is discarded. The system monitors the incoming sequence number on each RTP packet. If a packet takes more than 1.5 seconds, it is considered late and is discarded.

In a multiprogram transport stream (MPTS), the timestamp is uniquely set for every RTP packet, as any RTP packet many contain a number of multiplexed elementary streams. As a result, playout is based on the embedded timestamp in each RTP packet. In a single-program transport stream the inverse occurs. Many RTP packets can share the same timestamp as it is referenced from the start of a picture (and a picture can span many RTP packets). As an SPTS does not contain audio, its application is limited to content production and so only MPTS are supported.

Timestamp discontinuities do occur and are normally represented with the Marker bit (M) being set.

Playout time is determined by an internal playout timestamp. The playout timestamp is set independently from the actual timestamp in the packet. The recovered clock can compute the expected timestamp for the very next incoming RTP packet.

When a packet is received, it is first compared to existing packets in the buffer based on sequence number (assuming that a stream may be delayed for hundreds of milliseconds by a backup path yet still be valid); jitter tolerance is only evaluated if this packet is determined to be a new RTP packet eligible for buffer insertion. If jitter tolerance is exceeded, then a timestamp discontinuity is assumed and instead of setting the playout timestamp based on the contained RTP timestamp, the actual received time (offset by playout-buffer) is set for the RTP packet playout timestamp.

In normal operation, the clock is recovered from the timestamp field in the RTP header, is offset by the playout buffer configuration parameter, and is used to schedule playout of the packet. The playout clock is synchronized with the sender by using an adaptive clock recovery algorithm to correct for wander.

Algorithm summary

  • For a service marked LoT, if a loss of transport occurred, purge the buffer and reset all counters/timers.

  • If the service is UP, check the RTP packet sequence number. Compare to sequence numbers contained in the buffer. If no match then check last played sequence number. If the sequence number of this packet is between last played and last played + 4096 then consider this packet late and discard.

  • Check the expected timestamp recovered clock value and compare to RTP timestamp. If the expected timestamp is (-ve)jitter tolerance<timestamp<(+ve)jitter tolerance then the packet is admitted to the buffer with a playout timestamp per the embedded RTP timestamp. If jitter tolerance is not maintained this marks a discontinuity event. Set playout timestamp to current clock + playout buffer and enqueue.

Clock recovery

RFC 2250, RTP Payload Format for MPEG1/MPEG2 Video, defines the timestamp format for MPEG2 video streams (which may carry H.264 video): a 90kHz clock referenced to the PCR. Each ingest RTP packet has it’s timestamp inspected and it is used in an adaptive clock recovery algorithm. Importantly, these adjustments occur on ingress (not on playout). This serves as a long-term, stable, ingress stream recovered clock.

The 90kHz ingress stream recovered clock is adjusted for each service to account for the encoder’s reference clock/difference between the clock in the 7750 SR. This input timestamp is derived from the same RTP packet that is inserted into the buffer, and therefore may be subjected to significant jitter. The clock adjustment algorithm must only adjust clock in extremely small increments (in the order of microseconds) over a very long sample period (not bitrate) of at least 30 minutes.

Playout

Playout is the process of regenerating the stream based on the playout timestamp.

The playout is an exact offset to the ingress stream-recovered clock and serves as playout time for the video ISA. Because the timestamp is used for buffer playout, CBR, capped VBR, and VBR streams are all supported without pre-configuration. The playout buffer mechanism effectively removes network-induced jitter and restores the output to the rate of the original encoder.

Loss of transport

In the circumstance that the playout buffer is emptied an LoT is indicated. The video ISA resets playout timestamp, clock, sequence number, and so on for this event and awaits the next valid RTP packet for this service.

Perfect stream in relation to FCC/RET

Perfect stream can enhance the end user experience by removing network induced faults to the multicast stream. The egress of the perfect stream can be fed back into a separate ISA for the FCC/RET application. This ensures that the end user gets the best IPTV viewing experience from the start of a channel change. The perfect stream can be sent to the FCC/RET ISA by using extranet where FCC/RET resides on a separate VPRN instance.

Perfect stream in relation to VQM

Perfect stream uses two identical multicast streams traversing two diverse network paths to construct a multicast stream that is less susceptible to network faults. VQM can be configured in conjunction with perfect stream, which allows VQM to monitor the two ingress as well as the egress streams. By using the VQM statistics from all three streams, the operator can assess the quality of the network transporting the multicast stream, the performance of perfect stream, and the viewing quality for the end user. VQM and Perfect Stream can be enabled on the same video-group (the same ISA).

Video quality monitoring

The following terminology is used in this section:

  • TNC is an acronym for Technically Non-Conformant.

  • QoS is an acronym for Quality of Service.

  • POA is an acronym for Program Off Air.

  • TNC event (also known as impaired event) refers to a trap/alarm that detects an impairment event and is therefore termed TNC.

    An impaired event is said to have occurred if:

    • A PAT/PMT syntax error occurs in that second.

    • Continuity counter errors were detected.

    • PAT /PMT/PCR PIDs were not present in the video stream for a time period equal to or greater than the configured TNC value in the respective alarm.

      The default value of the impaired threshold in terms of milliseconds is:

      • PAT (100 ms)

      • PCR (100 ms)

      • PMT (400 ms)

    • An unreferenced PID is seen in the video stream which has not been referred in the PMT.

  • TNC seconds (also known as impaired seconds) refers to the number of seconds elapsed before an impaired event is detected and a TNC SNMP trap is sent. Use the following command to display TNC events.

    show video channel analyzer
  • Note: Although multiple TNC events may occur within a second, the displayed counters only increment once per second.
  • QoS event (also known as degraded event) refers to a trap/alarm that detects a degraded event and is therefore termed QoS. A QoS event is said to have occurred if PAT/PMT/PCR PIDs are absent in the video stream for a time period equal to or greater than the configured QoS value in their respective alarms.

    The default value of the degraded threshold in terms of milliseconds is:

    • PAT (200 ms)

    • PCR (200 ms)

    • PMT (800 ms)

  • QoS seconds (also known as degraded seconds) refer to the number of seconds elapsed before a degraded event was detected and a QoS SNMP trap was sent. Use the following command to display QoS events.

    show video channel analyzer
    Note: Although multiple QoS events may occur within a second, the displayed counters only increment once per second.
  • POA event (also known as error event) refers to a trap/alarm that detects an error event and is therefore termed POA.

    A POA event has occurred if:

    • A synchronization loss error has occurred for that particular second. A synchronization loss is said to have occurred if more than 1 consecutive synchronization byte error is seen in the stream.

    • PAT/PMT/PCR PIDs are absent from the video stream for a time period equal to or greater than the configured POA value.

      The default value of the degraded threshold in terms of milliseconds is:

      • PAT (500 ms)

      • PCR (500 ms)

      • PMT (2000 ms)

    • Traffic loss has occurred for that particular second.

    • A transport error indicator or TEI indicator is set in the transport stream packet header for that particular second in the video stream.

  • POA seconds (also known as error seconds) refer to the number of seconds elapsed before an error event is detected and a POA SNMP trap is sent. Use the following command to display POA events.

    show video channel analyzer
    Note: Although multiple POA events may occur within a second, the displayed counters only increment once per second.
  • Good seconds refer to the number of seconds where there are no impaired, degraded, or error events.

PID statistics are described in PID stats — description of fields

Table 1. PID stats — description of fields
Field Description

PID

Displays the value of the PID.

Is PCR PID

Can be set to Yes or No. If set to Yes, then it indicates that the PID is the PCR PID.

TEI Err Sec

Counts the number of seconds TEI was set for that particular PID.

Absent Err Secs

The number of seconds for which the PID was not seen for a particular interval of time which is decided by the alarms set for the non-Vid PID Absent and Video PID Absent.

PID bitrate

Calculated by counting the number of times the PID occurred in the last second x 188 x 8.

  • 188 = TS packet size

  • 8 = Number of bits in a byte

CC Err Secs

Number of seconds Continuity Counter errors were seen for that particular PID in the stream.

PID Type

Specifies that the PID is either video, audio, PAT, PMT, or PCR.

MPEG Stream Type

If the PID is video or audio, this field indicates how the video or audio is encoded. For example:
  • For video, H.265, H.264, or MPEG2 (only the decimal equivalent defined by the MPEG standard is displayed and not the string)

  • For audio, E-AC3, DTS-HD, AC-3, or MPEG-2 (only the decimal equivalent defined by the MPEG standard is displayed and not the string)

To address interval statistics, except for the PID statistics all other statistics described above have interval statistics. Information can be obtained about stream status for the last 1 minute, 5 minute, and 15 minute interval.

MDI - Media Delivery Index (RFC 4445, A Proposed Media Delivery Index (MDI))

  • Delay Factor (RFC 4445)

    The delay factor is a value which indicates the minimum amount of time a STB buffers to resolve network jitter (that is, it is the minimum STB buffer depth in ms). RTP timestamp is used as the definitive time indicator (the notional drain rate).

  • Loss Rate (RFC 4445)

    The Media Loss Rate is the number of media (Transport Stream) packets lost over a specific time interval. This is reported in TS/sec. Each RTP packet lost is assumed to have 7 TS packets lost.

Note: In absence of traffic MDI values are reported as N/A. These stats are reported over current (current second) , 1 minute, 5 minutes and 15 minutes intervals

In many instances IPTV operators are unable to identify the cause of visual impairments which are present in almost every video distribution network because the IPTV network has so many moving parts While head end transport-stream monitoring; full reference video analysis (comparing the source content to the encoded output), and; STB probes allow an operator to establish whether the contribution source, the encoder, or the network is the problem the network is a very complex thing.

Operators can use another measurement point in the network, just before the last mile such that network faults can be characterized as being between the head end and last mile (transport) or in the last-mile itself.

The multicast video quality monitoring solution provides an inspection point for the multicast video stream that is combined with other analysis methods to create a full view of video issues and help troubleshoot the part of the network causing the issue.

Video quality monitoring is one part of a video assurance program and is combined with:

  • TS analysis on the encoder output (to detect encoder errors)

  • Full-reference PSNR and PQR on the encoder output (to detect over-encoding, noise and other contribution or encoding artifacts)

  • STB reporting (such as packet-loss, RET events, packet errors) from the entire STB population

  • STB probes performing full-reference monitoring (against test streams)

  • STB probes performing channel-change times, estimated PSNR, and so on

Multicast video monitoring within the network can be positioned as complementary to STB reporting and head end analysis, and but should not attempt to perform either of these functions. Because the network node is not capable of decrypting a MPEG transport stream is primarily used to identify correctable and uncorrectable network errors, correlate them with network events (such as routing re-convergence, interface failure, and so on) and provide summary reports and alarms.

For operators who do not have existing STB probes or reporting, a network-based VQM solution can provide insight into quality issues the network may be contributing to, possibly reducing the amount of STB probe investment that is needed. (that is, both probes and the 7750 SR VQM reports many of the same issues in terms of picture quality, fewer probes are needed to test channel change delay, and so on).

The metrics which VQM can report are based on the use of RTP streams which provide per-packet sequencing and an indication of picture type. These two parameters along with measured bitrate allow VQM to produce estimated MOSv scores for both stream ingress (uncorrected) and stream egress (corrected) outputs.

Reportable metrics include:

  • Relevant SCTE-143 error counters

    • PAT

    • PMT

    • PCR

    • transport errors, and so on

  • ETSI TR 101 290

    • PID

    • SI repetition

    • degraded blocks/intervals, and so on

  • MDI (RFC 4445)

  • forwarded and impaired I-/B-/P-frame counts

  • GOP length

  • video/audio/stream bitrate

These metrics are collected for each multicast group and have relevant command options. Use the following command to generate a detailed numeric metrics report for a specific multicast group.

show video channel analyzer address detail

show video channel analyzer address 239.0.1.1 detail

===============================================================================
Video channel analyzer detail
===============================================================================
  Channel number : 1
-------------------------------------------------------------------------------
Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
MDI Delay Factor : 4                    MDI Loss Rate    :        0
Good Secs        : 0                    
 

===============================================================================
GOP Stats
===============================================================================
                    Min                 Max                 Avg
-------------------------------------------------------------------------------
GOP Length          10                  31                  24
Frames/Sec          21                  28                  25

===============================================================================
Frame Stats
===============================================================================
                    I-Frame             P-Frame             B-Frame
-------------------------------------------------------------------------------
Good                42                  957                 0
Bad                 0                   0                   0

===============================================================================
Error Stats
===============================================================================
                    POA Events          QoS Events          TNC Events
-------------------------------------------------------------------------------
PAT Rep             0                   1215                0
PMT Rep             0                   0                   0
PCR Rep             0                   0                   1
PAT Syntax Err      -                   0                   -
PMT Syntax Err      -                   0                   -
Sync Byte Err       -                   0                   -
Sync Loss           0                   -                   -
Unref PID           -                   -                   34600
Traffic Loss        0                   -                   -
-------------------------------------------------------------------------------
Overall             30285               77                  4238
-------------------------------------------------------------------------------
Reoccurring events only increment counter once every second

-------------------------------------------------------------------------------
Number of channels : 1
===============================================================================

Other information that is captured by VQM but can only be expressed on a per-PID basis. Use the following command to display PID address information per group.

show video channel pid address

The per-PID information captured by VQM includes the following:

  • CC Err secs
  • TEI Err secs
  • Absent Err secs

show video channel pid address 239.0.1.1

===============================================================================
Video Channel PID
===============================================================================
Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
PID              : 0                    PID Type         : pat
MPEG Stream Type : 0                    Is PCR PID       : No
Cc Err Secs      : 0                    TEI Err Secs     : 0
Absent Err Secs  : 0                    PID Bitrate      : 0

Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
PID              : 100                  PID Type         : pmt
MPEG Stream Type : 0                    Is PCR PID       : No
Cc Err Secs      : 0                    TEI Err Secs     : 0
Absent Err Secs  : 0                    PID Bitrate      : 0

Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
PID              : 101                  PID Type         : video
MPEG Stream Type : 27                   Is PCR PID       : Yes
Cc Err Secs      : 0                    TEI Err Secs     : 0
Absent Err Secs  : 0                    PID Bitrate      : 5564800

Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
PID              : 201                  PID Type         : audio
MPEG Stream Type : 3                    Is PCR PID       : No
Cc Err Secs      : 0                    TEI Err Secs     : 0
Absent Err Secs  : 0                    PID Bitrate      : 204544

Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
PID              : 202                  PID Type         : audio
MPEG Stream Type : 3                    Is PCR PID       : No
Cc Err Secs      : 0                    TEI Err Secs     : 0
Absent Err Secs  : 0                    PID Bitrate      : 132352

Service Id       : 31905555             Interface Name   : vi-1
Group Address    : 239.0.1.1            Source Address   : 10.10.10.10
PID              : 401                  PID Type         : other
MPEG Stream Type : 6                    Is PCR PID       : No
Cc Err Secs      : 0                    TEI Err Secs     : 0
Absent Err Secs  : 30310                PID Bitrate      : 0

Number of pids for this channel: 6 
                                   
-------------------------------------------------------------------------------
Number of channels : 1
===============================================================================

Event alarms are reported by log, syslog, or SNMP. The following is an example of an event trap.

Event trap

1 2017/02/11 18:11:20.42 UTC WARNING: VIDEO #2009 Base Video[1/video-300]
Service Id - 300, Video interface - video-300, Group address - 192.0.2.6,  Source address - 10.20.13.2 Last 10 seconds of analyzer state is good good good  good good good good good good poa

A trap is only raised when a POA, QoS, or TNC event occurs within the last 10 seconds. The trap captures events within the last 10 seconds. In the preceding example =, the first nine seconds were ‟good”, which indicates that no events occurred and that every single RTP packet was received. At the 10-second mark, a POA event occurred, which triggered the SNMP trap. This sampling continues every 10 seconds. If an event (POA, QoS, or TNC) continues to be detected, an SNMP trap is raised every 10 seconds.

When the analyzer detects 10 seconds of a ‟good” condition, another trap is raised to clear the alarm for the multicast (S,G). Subsequent alarms are raised and SNMP traps are triggered only when the analyzer detects another event (POA, QoS, or TNC).

Event clear trap

61 2016/10/18 15:40:56.83 UTC WARNING: VIDEO #2010 Base Video[1/video-300]

Analyzer state is cleared for - Service Id - 300, Video interface - video-300, Group address - 192.0.2.6, Source address - 10.20.13.2

VQM is an optional module available on the input side, or output side of the video ISA. On input, it is applied before perfect stream protection. Conversely when on the output side it is applied only to multicast streams after perfect stream protection.

Because of the large number of channels and the nature of measuring input and output sides, VQM is highly reliant on the use of RTP extensions to provide relevant transmission metrics to the VQM analysis module. In a typical head end, a multicast stream is scrambled to encrypt its video or audio. When this encryption occurs, it is typical for the entire payload of the transport stream (for the nominated PID) to be completely scrambled. The consequence of such is that the video and audio PES headers, which reveal much about the picture and timing information, are unavailable to the VQM program.

VQM uses intelligent RTP re-wrapping. RTP re-wrapping is a prerequisite for ad insertion and Fast Channel Change (FCC) and involves marking packets before encryption based on the picture type (most importantly, the start of the I frame of IDR frame in H.264.

The VSA as currently defined, re-multiplexes each transport stream into a new RTP packet. By doing so it allows the separation of different picture types into their own respective RTP packets, and the separation of audio packets from video packets to allow different synchronization in events of FCC. In effect, it pulls the elementary streams back into their component forms while retaining the syntax and structure of the MPTS.

For information about VSAs, see the 7450 ESS, 7750 SR, 7950 XRS, and VSR System Management Guide.

For quality analysis, additional information about the picture can be made available before scrambling. The quality analysis performed by the VQM module emphasizes impairments caused by network issues and transport stream syntax, based on the relative proximity of the router to the customer.

When the video ISA is deployed alongside the ALU VSA re-wrapper, a custom RTP header extension is sent with each RTP packet. The RTP header is shown in RTP header.

Figure 1. RTP header

Where:

B (Frame Begin Flag): set if a frame starts in this packet
 E (Frame End Flag): set if a frame finishes in this packet
 ST (Stream Type)
 00 video
 01 audio
 10 data/padd/other
 11 Reserved
 S (Switch bit): set to 1 in all RTP packets from the moment
 the client should do the IGMP join (rewrap does not fill it)
 r: reserved (set to 1)
 PRI: Packet Priority (coarse)
 FPRI: Fine-grained priority
 PRI FPRI dec DSCP
 --- ---- --- ----
 3 7 31 AF41 Video IDR frame
 3 0 24 AF41 Audio
 2 0 16 AF41 Reference frame (P in MPEG2, I or P or some Bs in AVC)
 1 7 15 AF42 Non-reference frame (most Bs in MPEG2, some Bs in AVC)
 1 5 13 AF42 Trans-GOP frames, undecodable in some circumstances (some Bs in MPEG2)
 0 4 4 AF43 Rest of cases (data, secondary videos, etc)
 0 1 1 AF43 Padding packets
where AF41=100010, AF42=100100, AF43=100110 (DSCP bits in the IP header)

VoIP/video/teleconferencing performance measurements

The feature provides ability to measure and provide statistics to allow reporting on voice and video quality for VoIP and teleconferencing (A/V) applications. A sampled deployment is shown in Voice/video monitoring deployment example . Although a distributed model is shown, a hub-and spoke model, with AA-ISA deployed only on one side of the traffic flow, is also supported.

Figure 2. Voice/video monitoring deployment example

Because of network-based AA, the operator has an ability to monitor voice, video, teleconferencing applications for an AA subscriber regardless of the type of that subscriber (a residential subscriber vs. a user of a business VPN service). AA-ISA monitors UDP/RTP/RTCP/SDP headers for each initiated call/application session (sampling may be provided, although it is expected that a sampling rate is smaller than that of TCP-applications because of the nature of the voice/video applications, which are longer lasting with smaller numbers of sessions or calls per subscriber). AA ISA gathers statistics and computes MOS-scores/R-factor results per each call or application session. At the end of a call (application session closure), AA-ISA sends the statistics and computed scores to a Cflowd collector (the Cflowd infrastructure that was introduced for TCP-performance but modified to carry voice/video specific data is used). The collector summarizes and presents the results to the operator/end user.

Mean Opinion Score (MOS) performance measurements solution architecture

AA-ISA integrates a third party MOS software stack to perform VoIP and video MOS measurements. This software provides:

  • call quality analysis using optimized ITU-T G.107

  • measurements of perceptual effects of burst packet loss and recency using ETSI TS 101 329-5 Annex E Extensions

  • measurements and analysis of RTCP XR (RFC3611) VoIP metrics payloads

AA software monitors the associated SDP channel and passes codec information (when available) to the subsystem which monitors VoIP. The video bearer channels traffic generates a wide variety of A/V performance metrics such as:

  • call quality metrics

    • listening and conversational quality MOS scores (MOS-LQ, MOS-CQ)

    • listening and conversational quality R-factors (R-LQ, R-CQ)

    • estimated PESQ scores (MOS-PQ)

    • separate R-factors for burst and gap conditions (R-Burst, R-Gap)

    • video MOS-V and audio MOS-A

    • video transmission quality (VSTQ)

  • video stream metrics

    • good and impaired I, B, P, SI, SP frame counts

    • automatic detection of GoP structure and other key video stream attributes such as image size, bit rate, codec type

  • transport (IP/RTP) metrics

    • packet loss rate, packet discard rate, burst/gap loss rates

    • packet delay variation/jitter

  • degradation factors (degradation because of loss, jitter, codec, delay, signal level, noise level, echo, recency)

When a flow terminates, AA software retrieves the flow MOS parameters from the subsystems, formats the info into a Cflowd record and forwards the record to a configured Cflowd collector (RAM).

RAM collects Cflowd records, summarizes these records using route of interest information (source/destinations). In addition, RAM provides the user with statistics (min/max/ avg values) for the different performance parameters that are summarized.

Retransmission and Fast Channel Change

RET and FCC overview

The following sections provide an overview of RET and FCC.

Retransmission

Retransmission (RET) for RTP (RFC 3550, RTP: A Transport Protocol for Real-Time Applications) is based on a client/server model where the client sends negative acknowledgments (NACKs) using Real-time Transport Control Protocol (RTCP) (RFC 4585, Extended RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/AVPF)) to a RET server when the client detects missing sequence numbers in the RTP stream. The RET server which caches the RTP stream, for example in a circular buffer, detects missing sequence numbers in the replies to the NACKs by resending the missing RTP packets as illustrated in RET server retransmission of a missing frame.

Figure 3. RET server retransmission of a missing frame

The format of the reply must be agreed upon by the RET client and server and can be an exact copy (Payload Type 33 as defined in RFC 3551, RTP Profile for Audio and Video Conferences with Minimal Control) or sent with a different Payload Type using an encapsulating RET header format (RFC 4588, RTP Retransmission Payload Format).

RET has been defined in standards organizations by the IETF in the above-noted RFCs and Digital Video Broadcasting (DVB) in ‟Digital Video Broadcasting (DVB); Transport of MPEG-2 TS Based DVB Services over IP Based Networks (DVB-IPTV Phase 1.4)” which describes the STB standards.

STBs that have a port of the Nokia RET/FCC Client SDK are an example of a standards-compliant RET Client implementation.

FCC

FCC is an Nokia method based on a client/server model for providing fast channel changes on multicast IPTV networks distributed over RTP. During a fast channel change, the FCC client initiates a unicast FCC session with the FCC server where the FCC server caches the video stream and sends the channel stream to the FCC client starting at the beginning of a Group of Pictures (GOP). Beginning at a GOP in the past minimizes the visual channel transition on the client/STB, but the FCC unicast stream must be sent at an accelerated rate in the time domain to allow the unicast stream to catch up to the main multicast stream, at which point, the FCC server signals to the client to join the main RTP stream.

FCC client/server protocol illustrates the FCC client and server communication.

Figure 4. FCC client/server protocol

There are two techniques for compressing the FCC unicast stream in time to allow the unicast session to catch up to the multicast stream: bursting and denting. When bursting, the stream is sent at a rate faster than multicast stream, for example, the stream can be ‟bursted” at 130% (or 30% over the nominal) multicast rate. ‟Denting” is a technique where less important video frames are dropped by the FCC server and not sent to the FCC client. Hybrid mode combines bursting and denting.

Bursting is illustrated in FCC bursting sent faster than nominal rate and denting is illustrated in FCC denting removing less important frames .

Figure 5. FCC bursting sent faster than nominal rate
Figure 6. FCC denting removing less important frames

When the unicast session has caught up to the multicast session, the FCC server signals to the FCC client to join the main multicast stream. The FCC server then sends the unicast session at a lower rate called the ‟handover” rate until the unicast session is terminated.

The FCC server functionality requires the Nokia 5910 Video Services Appliance (VSA) Re-Wrapper which is used to encapsulate and condition the multicast channel streams into RTP, adding important information in the RTP extension header. Also, the ISA FCC server requires an STB FCC client based on the Nokia FCC/RET Client SDK.

Retransmission server

The ISA RET server is supported within an IES or VPRN service context as applicable to the platform.

Whether the RET server is active for a specific multicast channel is defined in the multicast information policy where channels are defined. The channel configuration for the RET server within the policy is an explicit enable/disable of the local RET server (that is, whether the channel should be buffered), the RET buffer size for the channel in the ISA and a channel type (Picture-in-Picture (PIP), Standard Definition (SD) or High Definition (HD)). The RET buffer should be large enough to account for the round trip delay in the network; typically, a few hundred milliseconds is sufficient.

In an IES or VPRN service, up to 16 IP addresses can be assigned to a video interface.

The video policy within the multicast information policy defines the characteristics for the how the RET server should respond to NACKs received on an IP address. The different characteristics defined in a RET server ‟profile” are for each channel type (PIP, SD and HD):

  • enable/disable for the RET server (that is, whether requests should be serviced or dropped)

  • the RET rate (as a percentage of the nominal channel rate)

Typically, RET replies are sent below line rate because most dropped packets occur in the last mile and sending RET replies at a high rate may compound any last mile drop issues.

The IP address(es) of the RET server are defined in the unicast service instance, whereas the UDP port for the RET server is defined in the ‟default” bundle in the multicast information policy. The same UDP port is used for all RET server IP addresses that use the particular multicast information policy.

The ISA RET server supports the network model where there are separate service instances for unicast and multicast traffic that are cross-connected and multicast replicated downstream in the network. If there are separate multicast and unicast service instances, the unicast and multicast services must use the same multicast information policy.

FCC server

The ISA FCC server is supported within an IES or VPRN service context as applicable to the platform. VPRN services are not supported on the 7450 ESS.

Whether the FCC server is active for a specific multicast channel is defined in the multicast information policy where channels are defined. The channel configuration for the FCC server within the policy is an explicit enable/disable of the local FCC server (that is, whether the channel should be buffered) and a channel type PIP, SD or HD. When FCC is enabled, three (3) GOPs are stored in the buffer. The channel also defines an optional FCC tuning parameter called the FCC Minimum Duration which is used by the FCC server to determine which GOP to start the FCC unicast session. If there are too few frames of the current GOP stored in the FCC server buffer (based on number of milliseconds of buffering), the FCC server starts the FCC session from the previous GOP.

In an IES or VPRN service, up to 16 IP addresses can be assigned to a video interface.

The Video Policy within the multicast information policy defines the characteristics for the how the FCC server should respond to FCC requests received on an IP address. The different characteristics defined in an FCC server ‟profile” are for each channel type (PIP, SD and HD):

  • enable/disable for the FCC server (for example, should the requests be serviced or dropped)

  • the FCC mode (burst, dent or hybrid)

  • the burst rate (as a percentage above the nominal channel rate) for PIP, SD and HD channel types

  • the multicast handover rate (as a percentage of the nominal channel rate) used by the server after it has signaled the client to join the main multicast channel

Different FCC rates are allowed for each of the channel types because the channel types have different nominal bandwidths. For example, the last mile may only be able to reliably send a 25% burst (above nominal) for HD whereas the equivalent bit rate for SD is a 75% burst. The profiles are designed to provide flexibility.

The IP address of the FCC server is defined in the unicast service instance, whereas the UDP port for the FCC server is defined in the ‟default” bundle in the multicast information policy. The same UDP port is used for all FCC server IP addresses that use the particular multicast information policy.

The ISA FCC server supports the network model where there are separate service instances for unicast and multicast traffic that are cross-connected and multicast replicated downstream in the network. If there are separate multicast and unicast service instances, the unicast and multicast services must use the same multicast information policy.

Logging and accounting for RET and FCC

Statistics and accounting are supported, but limited to capturing 256 000 sessions per five-minute period. Configure both FCC and RET timers to five minutes. If either timer is changed, the logging and accounting statistics may not be accurate.

Statistics and accounting are available for the following:

  • RET server sessions statistics

  • FCC session statistics

RET and FCC server concurrency

Even though the previous sections discussed the RET server and FCC server as separate entities, the ISA can support RET and FCC servers at the same service at the same time. Therefore, the configuration commands and operational commands for the services are intermingled. If both the RET server and FCC server are enabled for a specific channel, a single buffer is used for caching of the channel.

A maximum bandwidth limit for all server requests can be defined for a specific ‟subscriber” which is equated with the source IP address. Before an ISA server processes a request, the ISA calculates the bandwidth to the subscriber required, and drops the request if the subscriber bandwidth limit is exceeded.

The ISA services RET and FCC requests on a first in, first out (FIFO) basis. Before servicing any request, the ISA calculates whether its egress bandwidth can handle the request. If there is insufficient egress bandwidth to handle the service request, the request is dropped. Near the ISA’s egress limits, RET requests generally continue to be serviced whereas FCC requests are dropped because RET sessions are generally a fairly small percentage of the nominal rate and FCC sessions are slightly below to above the nominal channel rate.

Prerequisites and restrictions

This section summarizes some key prerequisites and restrictions for the RET client, RET server and FCC server:

  • Both RET and FCC require RTP as the transport stream protocol.

  • FCC requires the Nokia 5910 VSA Re-Wrapper.

  • FCC requires an implementation of the Nokia 5910 STB Client.

  • The multicast information policies must be the same on multicast and unicast services which are cross connected downstream.

  • Up to 16 IP addresses can be configured for a Layer 3 service video interface (IES or VPRN) with each supporting a distinct profile.

  • There can be a maximum of 32 IP addresses across all Layer 3 service video interfaces per chassis.

Separate timers for FCC and RET

For each fast channel change, a new RTCP session is initialized, whereas for retransmission, the same RTCP session is always reused, with the same source and destination ports. The RTCP session duration is based on a timeout configuration, and a separate timeout option is available for FCC and RET. Use the following commands to configure the timeout:

  • MD-CLI
    configure multicast-management multicast-info-policy video-policy video-interface fcc-session-timeout
    configure multicast-management multicast-info-policy video-policy video-interface ret-session-timeout
  • classic CLI
    configure mcast-management multicast-info-policy video-policy video-interface fcc-session-timeout fcc-session-timeout
    configure mcast-management multicast-info-policy video-policy video-interface fcc-session-timeout ret-session-timeout
Note: Because the FCC RTCP session timeout is generally shorter than the RET session timeout, Nokia recommends configuring the FCC RTCP session timeout to a lower timeout value, accounting for the time required to complete a fast channel change and multicast handoff. This strategy frees RTCP sessions for other subscribers and improves efficiency.

Peak bandwidth and sessions per ISA

Use the following command to display the peak egress bandwidth and sessions per ISA. Each peak value is also marked with a timestamp.

show isa video-group

There are configurable watermarks for bandwidth and session consumption. The watermarks generate SNMP traps or log events when the ISA has reached the bandwidth or session thresholds. The egress bandwidth and session watermarks are configurable for FCC and RET separately or together. The SNMP trap or log event is generated as the configured watermark is exceeded, and is cleared if the egress rate falls below 10% of the watermark.

For example, if the maximum egress rate is 10 Gb/s and the watermark is set to 90%:

  • The alarm is generated when the egress rate exceeds the following:
    9 Gb/s (90% of 10 Gb/s)
  • The alarm is cleared when the egress rate falls below the following:
    0% at 8.1 Gb/s (10% of 9 Gb/s = 0.9 Gb/s, and 9 Gb/s - 0.9 Gb/s = 8.1 Gb/s)

Video support on ESA

The following applies to video support for the ESA:

  • The FCC and RET applications are supported.

  • VQM is not supported.

  • Perfect stream is supported on multi-complex platforms only.

  • SR-1/1s/2s/7/12/12e/7s/14s and SR-1-24D are currently supported.

  • ISA and ESA must not be used in the same video group.

IP Video for Live

Traditionally, IPTV is delivered over a broadband network and subscribers require IPTV STB to receive multicast content. Both the STB and its IP gateway must support IP multicast and IGMP. Because native IGMP cannot route beyond the first IP hop, subscriber reach is often restricted.

IP Video for Live further extends the FCC feature. Use the following command to enable IP Video for Live:

  • MD-CLI

    configure multicast-management multicast-info-policy video-policy video-interface extended-unicast
  • classic CLI

    configure mcast-management multicast-info-policy video-policy video-interface extended-unicast

Channel requests are triggered by an RTCP request. IPTV content is unicast to each individual subscriber using RTP over IP UDP, which:

  • eliminates the need to have both IP multicast support and IGMP support on end user devices

  • only requires subscribers to have IP connectivity. IPTV content is routed Over The Top (OTT) to individual subscribers.

  • supports all FCC, RET, and IP Video for Live on the same ISA/ESA. Therefore, the ISA/ESA that supports FCC/RET for broadband IPTV multicast can be reused for IP Video for Live.

  • allows OTT subscribers to use the same STB and software as the traditional broadband multicast IPTV subscribers. STB can be programmed to automatically use RTCP messages instead of IGMP, if IGMP requests are non-responsive. This allows for unified STB deployment regardless of the end subscriber type.

  • delivers video content using UDP with steady bit rate, which does not require network dimensioning for TCP burstiness or buffering

  • allows IP Video for Live subscribers to use the FCC and RET function. IP Video for Live uses RTCP control messages to retrieve IPTV content.

Before Release 23.7.R1, the ingress buffer of the multicast packet had a direct impact on the extended unicast streaming to the end subscriber. If the ingress multicast packet had missing packets, or a gap in the RTP sequence, the extended unicast streaming would abruptly stop for the end subscriber. Starting in Release 23.7.R1, the extended unicast feature can tolerate 20 missing consecutive packets from the multicast source. This tolerance also applies to jitter tolerance (20 packets).
Note: The jitter tolerance is based on the number of packets, instead of on the time; the higher the streaming throughout, the lower the jitter tolerance.
Overall, this jitter and loss tolerance helps improves the streaming experience.

Delayed IGMP join for FCC

The FCC solution requires the STB to switch from unicast to multicast after the fast channel change completes. The STB uses IGMP to switch to multicast. In some cases, the multicast process is delayed. Delay may occur because of IGMP processing delay, authentication delay, or network delay. Use the following command, which is used for IP Video for Live, to delay the IGMP for up to 5 minutes:

  • MD-CLI

    configure multicast-management multicast-info-policy video-policy video-interface extended-unicast
  • classic CLI

    configure mcast-management multicast-info-policy video-policy video-interface extended-unicast
Note: Nokia recommends enabling this command only in implementations where multicast delivery is delayed beyond 1.5 seconds. By default, extended unicast is disabled to ensure the optimal bandwidth for unicast to multicast handover.

Configuring video service components with CLI

This section provides information to configure RET/FCC using the command line interface.

Video services overview

The main entities of video configurations are:

  • video group

  • multicast information policy

    • a video policy to configure video interface properties

    • multicast bundles and channels to associate bundles/channels with video groups

  • within a service, configuring video interfaces and their associations with video groups

Video services configuration elements shows various configuration elements and how they are associated by configuration.
Figure 7. Video services configuration elements

A video interface within a service can have multiple IP address, and their association with the video interfaces within the video policy are based on IP addresses. Support for multiple video interface IP addresses for a specific video interface allows video characteristics (burst rate, retransmission format, and so on) for the channels associated with the video interface to be based on the IP address on which the request is received.

The bundle and channel configuration and the video interface configuration within the service are associated with a specific video group. If the request is received on a video interface for a channel not serviced by the video group associated with the video interface, the request is invalid and is dropped. Video services configuration elements displays an example of this is a request for mc-range2 received on IP1, IP2 or IP3. A request for mc-range2 would only be valid on IP4.

As with other multicast information policies, the bundle name default is a special bundle and is reserved for setting of default values. If a video parameter is not explicitly set in a bundle/channel, the value set in the default bundle is used.

Configuring an ISA module

The ISA hardware has an MDA form factor that is provisioned in the same manner as other MDAs.

Use the following commands to configure an ISA module.

configure card card-type
configure card mda mda-type
MD-CLI
[ex:/configure card 9]
A:admin@node-2# info
    card-type iom4-e-b
    mda 1 {
        mda-type isa2-aa
    }
    mda 2 {
        mda-type isa2-aa
    }
    fp 1 {
    }
classic CLI
A:node-2>config>card# info
----------------------------------------------
        card-type iom4-e-b
        mda 1
            mda-type isa2-bb
        exit
        mda 2
            mda-type isa2-bb
        exit
        fp 1
        exit
----------------------------------------------

Configuring a video group

When used for video services, ISA-MSes are logically grouped into video groups that pool the ISA buffering and processing resources into a single logical entity.

Use the commands in the following context to configure a video group.

configure isa video-group 

The following example shows video-group 1 with a single ISA configured in slot 2/MDA 1.

MD-CLI
[ex:/configure isa]
A:admin@node-2# info
    video-group 1 {
        admin-state enable
        description "Video Group 1"
        mda 1/2 { }
    }
classic CLI
A:node-2>config>isa# info
===============================================================================
        video-group 1 create
            description "Video Group 1"
            primary 7/2
            no shutdown
        exit
===============================================================================

Within the video group configuration, there are specific video application commands to enable features. These commands are described in the configuration examples for the application. Depending on the video application, more than one primary ISA-MS is allowed increasing the egress capacity of the video group.

ISA-MS in a single video group cannot be on the same IOM. An IOM can accommodate two ISA-MS modules provided that the ISA-MS are members of different video groups.

Configuring a video SAP and video interface in a service

Video features in a VPRN service require the user to create the following:

  • a video SAP

  • a video interface

A video SAP is similar to other SAPs in the system in that QoS and filter policies can be associated with the SAP on ingress (traffic leaving the ISA and ingressing the system) and egress (traffic leaving system and entering the ISA).

The video SAP is associated with a video group. Channels are also associated with a video group which is what establishes the link between what channels can be referenced through the video SAP. The multicast information policy associated with the service is where the channel to video group association is defined.

A single VPRN service can be used to support all video applications. However, it is possible to use two different VPRNs for a FCC/RET service; one VPRN is configured with a FCC/RET server to process FCC/RET requests, and a second VPRN is configured to support only the buffering of the multicast video content. In this case, within the FCC/RET server VPRN, the multicast service of the VPRN (service ID) must be specified.

Another important video services option in a multicast information policy is the administrative bandwidth defined for the channel. Many video applications use the bandwidth to determine if sufficient ISA egress bandwidth exists to service or drop a service request.

Video interface configuration (MD-CLI)
[ex:/configure service ies "1"]
A:admin@node-2# info
    customer "1"
    video-interface "video-100" {
        multicast-service 5
        video-sap {
            video-group-id 4
        }
        address 10.1.1.254/8 { }
        address 192.168.0.254/8 { }
    }
Video interface configuration (classic CLI)
A:node-2>config>service>ies# info
----------------------------------------------
            shutdown
            video-interface "video-100" create
                shutdown
                video-sap 4
                exit
                address 10.1.1.254/8
                address 192.168.0.254/8
                multicast-service 5
            exit
----------------------------------------------

Basic multicast information policy configuration

Multicast information policies are used by the video applications to define multicast channel attributes and video policies which contains application-specific configuration for a video interface IP address.

It is within the multicast information policy bundles, channels and source-overrides that a video group is assigned to a channel. The video group association is inherited from the more general construct unless it is explicitly disabled.

The administrative bandwidth for channels at the bundle, channel or source-override level is also defined in the multicast information policy. Video applications use the administrative bandwidth here when a channel rate estimate is needed.

A video policy is defined within the multicast information policy for a specific video interface IP address. The IP address for the video policy is the key value that associates it with a specific video interface IP address within a service associated with overall multicast information policy.

See the 7450 ESS, 7750 SR, and VSR Triple Play Service Delivery Architecture Guide for CLI command descriptions and syntax usage information to configure multicast info policies.

The following example displays a multicast information policy configuration.

MD-CLI
[ex:/configure multicast-management]
A:admin@node-2# info
    multicast-info-policy "ies100" {
        bundle "10.5.6.140" {
            admin-bw 8000
            video {
                local-rt-server true
                rt-buffer-size 3000
                video-group 1
            }
            channel start 10.5.6.140 end 10.5.6.140 {
            }
        }
        bundle "10.5.6.241-10.5.6.243" {
            admin-bw 12000
            video {
                rt-buffer-size 4000
                video-group 1
            }
            channel start 10.5.6.241 end 10.5.6.243 {
            }
        }
    }
classic CLI
A:node-2>config>mcast-mgmt># info   
----------------------------------------------
            multicast-info-policy "ies100" create
                bundle "10.5.6.140" create
                    admin-bw 8000
                    video
                        video-group 1
                        local-rt-server
                        rt-buffer-size 3000
                    exit
                    channel "10.5.6.140" "10.5.6.140" create
                    exit
                exit
                bundle "default" create
                exit
                bundle "5.6.241-5.6.243" create
                    admin-bw 12000
                    video
                        video-group 1
                        rt-buffer-size 4000
                    exit
                    channel "10.5.6.241" "10.5.6.243" create
                    exit
                exit                  
            exit
----------------------------------------------

Sample configurations

The following example displays the configuration of the VQM with packet selection.

VQM configuration with packet selection (MD-CLI)

[ex:/configure multicast-management]
A:admin@node-2# info
    multicast-info-policy "vqm" {
        bundle "ixia" {
            channel start 10.5.5.6 end 10.5.5.7"
                admin-bw 2000    
                video {
                    rt-buffer-size 1000
                    video-group 4
                    stream-selection {
                        source1 192.168.2.1
                        intf1 "ineo-ingress1"
                        source2 192.168.2.1
                        intf2 "ineo-ingress2"
                    analyzer {
                        alarms {
                            cc-error true
                            pat-repetition tnc 400 qos 600 poa 700
                            pat-syntax
                            pcr-repetition tnc 400 qos 600 poa 700
                            pid-pmt-unref
                            pmt-repetition tnc 2300 qos 2500 poa 2700
                            pmt-syntax
                            scte-35
                            tei-set
                            ts-sync-loss
                            vid-pid-absent 5000 
                            non-vid-pid-absent 5000 {
                        }
                    }
               }
               source-override 192.168.2.1 {
            }
        }
    }

[ex:/configure service ies "300"]
A:admin@node-2# info
    admin-state enable
    description "Default IES description for service ID 300"
    customer "1"
    vpn-id 300
    video-interface "video-300" {
        admin-state enable
        video-sap {
            video-group-id 1
        }
        channel 10.5.5.6 source 192.168.2.1 {
            channel-name "Ineoquest-1"
            zone-channel 10.5.5.6 source 10.20.0.1 { 
                adi-channel-name "Ineoquest-1-1"
            }
        }
    }

[ex:/configure router "Base"]
A:admin@node-2# info
    ecmp 2
    multicast-info-policy "vqm"
    interface "ineo-ingress1" {
        port 3/2/12
        ingress {
            filter {
                ip "100"
            }
        }
        ipv4 {
            primary {
                address 10.200.16.1
                prefix-length 24
            }
        }
    }
    interface "ineo-ingress2"
        port 5/1/1
        ingress
            filter {
                ip 200
            }
        }
        ipv4 {
            primary {
                address 10.200.17.1
                prefix-length 24
            }
        }
    }
    interface "ixia-egress"
        port 3/2/15
        ipv4 {
            primary {
                address 10.200.15.1
                prefix-length 24
            }
        }
    }
    interface "system"
        ipv4 {
            primary {
                address 10.20.1.1
                prefix-length 32
            }
        }
    }
    static-routes {
        route 192.168.2.1/32 route-type multicast {
            next-hop "10.200.16.2" {
                admin-state enable
            }
            next-hop "10.200.17.2" {
                admin-state enable
            }
        }
    }
    
[ex:/configure router "Base" igmp]
A:admin@node-2# info
    ...
    interface "video-300-D" {  
        static {
            group 10.5.5.6 {
                source 192.168.2.1 { }  
            }
        }
    }
    interface "video-300-D2" {  
        static {
            group 10.5.5.6 {
                source 192.168.2.1
            }
        } 
    } 
    interface "ixia-egress" {  
        static {
            group 10.5.5.6 {
                source 10.20.0.1
            }
        } 
    } 

[ex:/configure router "base" pim]
A:admin@node-2# info
    interface "video-300" {
        admin-state enable
    }  
    interface "ineo-ingress1" {
        admin-state enable
        multicast-senders always
    }
    interface "ineo-ingress2" {
        admin-state enable
        multicast-senders always
    }
    rp {
        ipv4 {
            bsr-candidate {
                admin-state enable
           }
            rp-candidate {
                admin-state enable  
            }
        }
    }

[ex:/configure isa]
A:admin@node-2# info
    video-group 4 {
        admin-state enable
        analyzer
        stream-selection true
        mda 3/1 { }
    }

VQM configuration with packet selection (classic CLI)

A:node-2>config>mcast-mgmt># info
----------------------------------------------
            multicast-info-policy "vqm" create
                bundle "ixia" create
                    channel "10.5.5.6" "10.5.5.7" create
                        admin-bw 20000
                        video
                            video-group 4
                            rt-buffer-size 1000
                            analyzer
                                alarms
                                    cc-error
                                    pat-repetition tnc 400 qos 600 poa 700
                                    pat-syntax
                                    pid-pmt-unref
                                    pmt-repetition tnc 2300 qos 2500 poa 2700
                                    pmt-syntax
                                    vid-pid-absent 5000
                                    non-vid-pid-absent 5000
                                    pcr-repetition tnc 400 qos 600 poa 700
                                    scte-35
                                    tei-set
                                    ts-sync-loss
                                exit
                            exit
                            stream-selection source1 192.168.2.1 intf1 "ineo-ingress1" 
source2 192.168.2.1 intf2 "ineo-ingress2"
                        exit
                        source-override "192.168.2.1" create
                        exit
                    exit
                exit
                bundle "default" create
                exit
            exit
----------------------------------------------
A:node-2>config>service# info
------------------------adm----------------------
        customer 1 create
            description "Default customer"
        exit
        ies 300 customer 1 vpn 300 create
            description "Default Ies description for service id 300"
            video-interface "video-300" create
                video-sap 4
                exit
                address 10.20.255.254/16
                channel 10.5.5.6 source 192.168.2.1 channel-name "Ineoquest-1"
                    zone-channel 10.5.5.6 source 10.20.0.1 adi-channel-name "Ineoquest-
1-1"
                exit
                adi
                exit
                no shutdown
            exit
            service-name "XYZ Ies 300"
            no shutdown
        exit
----------------------------------------------
A:node-2>config>router# info
----------------------------------------------
#--------------------------------------------------
echo "IP Configuration"
#--------------------------------------------------
        interface "ineo-ingress1"
            address 10.200.16.1/24
            port 3/2/12
            ingress
                filter ip 100
            exit
        exit
        interface "ineo-ingress2"
            address 10.200.17.1/24
            port 5/1/1
            ingress
                filter ip 200
            exit
        exit
        interface "ixia-egress"
            address 10.200.15.1/24
            port 3/2/15
        exit
        interface "system"
            address 10.20.3.1/32
        exit
        ecmp 2
        multicast-info-policy "vqm"
        static-route 192.168.2.1/32
            next-hop 10.200.16.2
               no shutdown
            exit
            next-hop 10.200.17.2
               no shutdown
            exit
        exit
#--------------------------------------------------
echo "IGMP Configuration"
#--------------------------------------------------
        igmp
            interface "video-300-D"
                static
                    group 10.5.5.6
                        source 192.168.2.1
                    exit
                exit
            exit
            interface "video-300-D2"
                static
                    group 10.5.5.6
                        source 192.168.2.1
                    exit
                exit
            exit
            interface "ixia-egress"
                static
                    group 10.5.5.6
                        source 10.20.0.1
                    exit
                exit
            exit
        exit
#--------------------------------------------------
echo "PIM Configuration"
#--------------------------------------------------
        pim
            rpf-table rtable-m
            interface "video-300"
            exit
            interface "ineo-ingress1"
                multicast-senders always
            exit
            interface "ineo-ingress2"
                multicast-senders always
            exit
            rp
                static
                exit
                bsr-candidate
                    shutdown
                exit
                rp-candidate
                    shutdown
                exit
            exit
        exit
----------------------------------------------
A:node-2>config>isa# info
----------------------------------------------
        video-group 4 create
            analyzer
            stream-selection
            primary 3/1
            no shutdown
        exit
----------------------------------------------

The following output displays configurations of VQM without packet selection.

VQM configuration without packet selection (MD-CLI)

[ex:/configure service ies "300"]
A:admin@node-2# info
    admin-state enable
    description "Default IES description for service ID 300"
    customer "1"
    vpn-id 300
    interface "linux-egress" {
        sap 3/2/17 {
            description "sap-300-10.10.34.228"
        }
        ipv4 {
            primary {
                address 10.10.34.228
            }
        }
    }
    interface "linux-ingress" {
        sap 3/2/17 {
            description "sap-300-10.10.33.228"
        }
        ipv4 {
            primary {
                address 10.10.33.228
            }
        }
    }
    video-interface "video-300" {
        admin-state enable
        video-sap {
            video-group-id 2
        }
        address 10.20.13.1/24 { }
        }
        channel 10.5.5.6 source 192.168.2.1 {
            channel-name "A2-SP3"
                zone-channel 10.5.5.6 source 10.20.13.2 { 
                adi-channel-name "A2-SP3-1"
            }
        }
    }

[ex:/configure router "Base"]
A:admin@node-2# info
    ...
    multicast-info-policy "A-server"
    interface "system" {
        ipv4 {
            primary {
                address 10.20.1.1
                prefix-length 32
            }
        }
    }
    ...
    static-routes {
        route 128.251.33.0/24 {
            next-hop "10.10.33.229" {
                admin-state enable
            }
        }
        route 192.168.2.0/24
            next-hop "10.10.33.229" {
                admin-state enable
            }
        }
    }
    
[ex:/configure router "Base" igmp]
A:admin@node-2# info
    interface "video-300-D" {  
        static {
            group 10.5.5.6 {
                source 192.168.2.1 { }  
            }
        }
    }
    interface "linux-egress" {  
        static {
            group 10.5.5.6 {
                source 10.20.13.2
            }
        } 
    } 

[ex:/configure router "base" pim]
A:admin@node-2# info
    interface "linux-ingress" {
        admin-state enable
        hello-interval 0
        multicast-senders always 
    }  
    interface "linux-egress" {
        admin-state enable
        hello-interval 0
    }
    apply-to all
    }
    rp {
        static 
        bsr-candidate {
            admin-state enable
        }
         rp-candidate {
             admin-state enable  
            }
        }
    }

[ex:/configure isa]
A:admin@node-2# info
    video-group 2 {
        admin-state enable
        analyzer
        mda 2/1 { }
    }
[ex:/configure multicast-management]
A:admin@node-2# info
    multicast-info-policy "A-server" {
        bundle "LiveTV" {
            channel start 10.5.6.243 end 10.5.6.243"
                admin-bw 3000    
                video {
                    rt-buffer-size 1000
                    video-group 2
                }
            }
            channel start 10.5.5.6 end 10.5.5.6"
                admin-bw 5000   
                video {
                    rt-buffer-size 1000
                    video-group 2
                    analyzer {
                        alarms {
                            cc-error true
                            pat-repetition tnc 400 qos 600 poa 700
                            pat-syntax
                            pid-pmt-unref
                            pmt-repetition
                            pmt-syntax
                            vid-pid-absent 1000 
                            non-vid-pid-absent 1000 
                            pcr-repetition tnc 200 qos 400 poa 600
                            scte-35
                            tei-set
                            ts-sync-loss
                            report-alarm severity tnc {
                        }
                    }
                }   
                source-override 192.168.2.1 {
            }
        }
        bundle "mp2ts-ads" {
            channel start 10.4.5.1 end 10.4.5.254"
                admin-bw 5000    
                video {
                    rt-buffer-size 1000
                    video-group 2
                }
            }
        }
    }

VQM configuration without packet selection (classic CLI)

----------------------------------------------
A:node-2>config>service# info
----------------------------------------------
        customer 1 create
            description "Default customer"
        exit
        ies 300 customer 1 vpn 300 create
            description "Default Ies description for service id 300"
            interface "linux-ingress"  create
                address 10.10.33.228/24
                sap 3/2/17 create
                    description "sap-300-10.10.33.228"
                exit
            exit
            interface "linux-egress"  create
                address 10.10.34.228/24
                sap 3/2/7 create
                    description "sap-300-10.10.34.228"
                exit
            exit
            video-interface "video-300" create
                video-sap 2
                exit
                address 10.20.13.1/24
                channel 10.5.5.6 source 192.168.2.1 channel-name "A2-SP3"
                    zone-channel 10.5.5.6 source 10.20.13.2 adi-channel-name "A2-SP3-1"
                exit
                adi
                exit
                no shutdown
            exit
            service-name "XYZ Ies 300"
            no shutdown
        exit
----------------------------------------------

A:node-2>config>router# info
----------------------------------------------
#--------------------------------------------------
echo "IP Configuration"
#--------------------------------------------------
        interface "system"
            address 10.20.1.1/32
        exit
        multicast-info-policy "A-server"
#--------------------------------------------------
echo "Static Route Configuration"
#--------------------------------------------------
        static-route 128.251.33.0/24
            next-hop 10.10.33.229
               no shutdown
            exit
        static-route 192.168.2.0/24
            next-hop 10.10.33.229
               no shutdown
            exit
        exit
#--------------------------------------------------
echo "IGMP Configuration"
#--------------------------------------------------
        igmp
            interface "video-300-D"
                static
                    group 10.5.5.6
                        source 192.168.2.1
                    exit
                exit
            exit
            interface "linux-egress"
                static
                    group 10.5.5.6
                        source 10.20.13.2
                    exit
                exit
            exit
        exit
#--------------------------------------------------
echo "PIM Configuration"
#--------------------------------------------------
        pim
            interface "linux-ingress"
                hello-interval 0
                multicast-senders always
            exit
            interface "linux-egress"
                hello-interval 0
            exit
            apply-to all
            rp
                static
                exit
                bsr-candidate
                    shutdown
                exit
                rp-candidate
                    shutdown
                exit
            exit
        exit
----------------------------------------------

A:node-2>config>isa# info
----------------------------------------------
        video-group 2 create
            analyzer
            primary 2/1
            no shutdown
        exit
----------------------------------------------

A:node-2>config>mcast-mgmt># info
----------------------------------------------
            multicast-info-policy "A-server" create
                bundle "LiveTv" create
                    channel "10.5.6.243" "10.5.6.243" create
                        admin-bw 3000
                        video
                            video-group 2
                            rt-buffer-size 1000
                        exit
                    exit
                    channel "10.5.5.6" "10.5.5.6" create
                        admin-bw 5000
                        video
                            video-group 2
                            rt-buffer-size 1000
                            analyzer
                                alarms
                                    cc-error
                                    pat-repetition tnc 200 qos 400 poa 600
                                    pat-syntax
                                    pid-pmt-unref
                                    pmt-repetition
                                    pmt-syntax
                                    vid-pid-absent 1000
                                    non-vid-pid-absent 1000
                                    pcr-repetition tnc 200 qos 400 poa 600
                                    scte-35
                                    tei-set
                                    ts-sync-loss
                                    report-alarm severity tnc
                                exit
                            exit
                        exit
                        source-override "192.168.33.37" create
                        exit
                    exit
                exit
                bundle "default" create
                exit
                bundle "mp2ts-ads" create
                    channel "10.4.5.1" "10.4.5.254" create
                        admin-bw 5000
                        video
                            video-group 2
                            rt-buffer-size 1000
                        exit
                    exit
                exit
            exit
----------------------------------------------

Configuring RET/FCC video components with CLI

This section provides information to configure RET/FCC using the command line interface.

Configuring RET/FCC video features in the CLI

The following sections provide configuration examples for the RET client, RET server and FCC server.

Configuring the RET server

This section provides an example configuration for the RET server. The configuration example has the following assumptions:

  • a single ISA-MS in slot 2/1 in video group 1

  • a single channel 192.0.2.1 within multicast bundle ‟b1” with an administrative bandwidth of 2700 kb/s defined in multicast-info-policy policy-name

  • a retransmission buffer for the channel set to 300 milliseconds

  • RET rate is 5% of nominal

  • local RET server address is 10.3.3.3 and destination port is UDP 4096

The first step is to configure the video group, including the RET server, and the ISA-MS hardware. The local-rt-server command in the example enables the local RET server on the video group.

Video group with RET server configuration (MD-CLI)
[ex:/configure isa]
A:admin@node-2# info
    video-group 1 {
        admin-state enable
        local-rt-server true
        mda 2/1 { }
    }

[ex:/configure card 2 mda 1]
A:admin@node-2# info
    mda-type isa-ms-v
Video group with RET server configuration (classic CLI)
A:node-2>config>isa# info
----------------------------------------------
        video-group 1 create
            local-rt-server
            primary 2/1
            no shutdown
        exit
----------------------------------------------

A:node-2>config>card>mda# info
----------------------------------------------
            mda-type isa-ms
----------------------------------------------

The channel command options for 192.0.2.1 are configured in the multicast management policy. The channel configuration includes the administrative bandwidth and the channel’s association with video group 1.

Multicast information policy configuration (MD-CLI)
[ex:/configure multicast-management multicast-info-policy "ies100"]
A:admin@node-2# info
    bundle "bl" {
        admin-bw 2700
        video {
            local-rt-port 4096
            rt-buffer-size 300
            video-group 2
        }
        channel start 192.0.2.1 end 192.0.2.1 {
        }
    }
    video-policy {
        video-interface 10.3.3.3 {
            rt-rate 5
            hd {
                local-rt-server true
            }
            pip {
                local-rt-server true
            }
            sd {
                local-rt-server true
            }
        }
    }
Multicast information policy configuration (classic CLI)
A:node-2>config>mcast-mgmt>mcast-info-plcy# info
----------------------------------------------
            bundle "default" create
                local-rt-port 4096
            exit
            bundle "b1" create
                admin-bw 2700
                video
                    video-group 2
                    rt-buffer-size 300
                exit
                channel "192.0.2.1" "192.0.2.1" create
                exit
            exit
            video-policy
                video-interface 10.3.3.3 create
                    rt-rate 5
                    hd
                        local-rt-server
                    exit
                    sd
                        local-rt-server
                    exit
                    pip
                        local-rt-server
                    exit
                exit
            exit
----------------------------------------------

The local-rt-port command in the bundle defines the destination UDP port used to reach the local RET server on the service where the multicast information policy is applied.

In the classic CLI, the RET server port can only be defined in the bundle ‟default” and applies for all bundles in the policy. If no value is specified, the default is used.

In the example, in the bundle ‟b1” the local-rt-server command enables the RET server for all channels in the bundle, and the rt-buffer-size command sets the retransmission buffer for all channels in the bundle to 300 milliseconds.

In the video policy in the example, the local-rt-server commands for the video interface 10.3.3.3 enables the RET server on that interface for all channel types ‟hd” (High Definition), ‟sd” (Standard Definition) and ‟pip” (Picture-in-Picture). The rt-rate command in the policy indicates that the retransmission rate is 5% of the nominal rate for all channel types; individual rates can be defined if needed.

In the following example, for the RET server in an IES or VPRN service instance and router configuration, the following commands are used to complete the RET server configuration:

  1. associate the service with the multicast information policy

  2. create the video interface ‟vi” and assign IP address 10.3.3.3

  3. create video SAP and associate it with video group 1

  4. create a static IGMP join on video-interface ‟vi” for the channel 192.0.2.1

In the following example, the services available on the video interface address 10.3.3.3 are defined in the video policy in which the RET server is enabled.

Video interface to service association and IGMP and PIM configuration (MD-CLI)
[ex:/configure service ies "100"]
A:admin@node-2# info
    video-interface "vi" {
        admin-state enable
        video-sap {
            video-group-id 1
        }
        address 10.3.3.3/32 { }
        }
    }

[ex:/configure router "base"]
A:admin@node-2# info  
        multicast-info-policy "ies100"
        igmp
            interface "vi"
                static
                    group 192.0.2.1
                        starg
                    }
                }
            }
        }
        pim
            interface "vi" {
        }
 
Video interface to service association and IGMP and PIM configuration (classic CLI)
A:node-2>config>service>ies# info
----------------------------------------------
            video-interface "vi" create
                video-sap 1
                exit
                address 10.3.3.3/32
                no shutdown
            exit

A:node-2>config>router# info
----------------------------------------------
    ...
    multicast-info-policy "ies100"
    igmp
        interface "vi"
            static
                group 192.0.2.1
                    starg
                exit
            exit
        exit
    pim 
        interface "vi"
        exit
    exit
----------------------------------------------

Configuring the FCC server

This section provides an example configuration for the FCC server. The configuration example has the following assumptions:

  • a single ISA-MS in slot 2/1 in video group 1

  • a single channel 192.0.2.1 within multicast bundle ‟b1” with an administrative bandwidth of 8000 kb/s defined using the multicast-info-policy command

  • FCC mode burst with a rate 130% of nominal for HD, 200% for SD, and disabled for PIP

  • local FCC server address10.3.3.3 and destination port UDP 4098

The first step in the configuration is to configure video group 1 enabling the FCC server and the ISA-MS hardware. The fcc-server command in the example enables the FCC server on the video group.

Video group with FCC server configuration (MD-CLI)
[ex:/configure isa]
A:admin@node-2# info
    video-group 1 {
        admin-state enable
        fcc-server true
        mda 2/1 { }
    }

[ex:/configure card 2 mda 1]
A:admin@node-2# info
    mda-type isa-ms
Video group with FCC server configuration (classic CLI)
A:node-2>config>isa# info
----------------------------------------------
        video-group 1 create
            fcc-server
            primary 2/1
            no shutdown
        exit
----------------------------------------------

A:node-2>config>card>mda# info
----------------------------------------------
            mda-type isa-ms
----------------------------------------------

The channel parameters for 192.0.2.1 are configured in the multicast-info-policy configuration. The channel configuration includes the administrative bandwidth and the channel’s association with video group 1.

FCC server configuration for a multicast information policy (MD-CLI)
[ex:/configure multicast-management multicast-info-policy "ies100"]
A:admin@node-2# info
    bundle "bl" {
        admin-bw 8000
        video {
            fcc-server true
            fcc-channel-type hd
            local-fcc-port 4098
            video-group 1
        }
        channel start 192.0.2.1 end 192.0.2.1 {
        }
    }
    video-policy {
        video-interface 10.3.3.3 {
            rt-rate 5
            hd {
                fcc-server {
                    mode burst
                }
                fcc-burst 30
            }
            pip
            }
            sd {
                fcc-server {
                    mode burst
                }
                fcc-burst 100
            }
        }
    }
FCC server configuration for a multicast information policy (classic CLI)
A:node-2>config>mcast-mgmtmcast-info-plcy# info
----------------------------------------------
            bundle "default" create
                local-fcc-port 4098
            exit
            bundle "b1" create
                admin-bw 8000
                video
                    video-group 1
                    fcc-server 
                    fcc-channel-type hd
                exit
                channel "192.0.2.1" "192.0.2.1" create
                exit
            exit
            video-policy
                video-interface 10.3.3.3 create
                    rt-rate 5
                    hd
                        fcc-server mode burst
                        fcc-burst 30
                    exit
                    sd
                        fcc-server mode burst
                        fcc-burst 100
                    exit
                    pip
                        no fcc-server
                    exit
                exit
            exit
----------------------------------------------

The local-fcc-port command in the bundle defines the destination UDP port used to reach the FCC server on the service where the multicast information policy is applied.

In the classic CLI, the FCC server port can only be defined using the local-fcc-port command in the bundle ‟default” and applies for all bundles in the policy. If no value is specified, the default is used.

In the bundle ‟b1”, the fcc-server command enables the FCC server for all channels in the bundle, and the fcc-channel-type hd command sets the channel type for all channels in the bundle to ‟hd” (High Definition).

In the preceding video policy example, the fcc-server commands for the video interface 10.3.3.3 enables the FCC server on that interface for all channel types ‟hd” (High Definition), ‟sd” (Standard Definition). There is no FCC server enabled for the Picture-in-Picture (PIP) channels on the video interface.

The fcc-burst command in the policy indicates that the burst rate over the nominal rate for the channel type, that is, HD at 130% (30% over nominal) and SD at 200% (100% over nominal).

In the following example, for the FCC server in an IES or VPRN service instance and router configuration, the following commands are used to complete the FCC server configuration:

  1. associate the service with the multicast information policy

  2. create the video interface ‟vi” and assign IP address 10.3.3.3

  3. create video SAP and associate it with video group 1

  4. create a static IGMP join on video-interface ‟vi” for the channel 192.0.2.1

The services available on the video interface address are defined in the video policy in which the FCC server was enabled.

Video service association with IGMP and PIM configuration (MD-CLI)
[ex:/configure service ies "100"]
A:admin@node-2# info
    video-interface "vi" {
        admin-state enable
        video-sap {
            video-group-id 1
        }
        address 10.4.4.4/32 { }
        }
    }

[ex:/configure router "base"]
A:admin@node-2# info  
        ....
        multicast-info-policy "ies100"
        igmp
            interface "vi"
                static
                    group 192.0.2.1
                        starg
                    }
                }
            }
        }
        pim
            interface "vi" {
        }
        ...
 
Video service association with IGMP and PIM configuration (classic CLI)
A:node-2>config>service>ies# info
----------------------------------------------
            video-interface "vi" create
                video-sap 1
                exit
                address 10.4.4.4/32
                no shutdown
            exit
----------------------------------------------

A:node-2>config>router# info
----------------------------------------------
    ...
    multicast-info-policy "ies100"
    igmp
        interface "vi"
            static
                group 192.0.2.1
                    starg
                exit
            exit
        exit
    pim 
        interface "vi"
    exit
    ...
----------------------------------------------

Logging and accounting collection for video statistics

The following example shows logging and accounting configuration for collecting video statistics. Accounting requires the platforms support no more than 256,000 sessions and the FCC/RET timer must be set to 5 minutes. If these conditions are not met, the accounting record may not be accurate.

Logging and accounting configuration for video statistics (MD-CLI)
[ex:/configure log]
A:admin@node-2# info
        file 1
            compact-flash-location {
                primary cf3:
        }
        accounting-policy 1 {
            admin-state disable
            collection-interval 5
            record video
            destination {
                file "1"
            }
        }
    }
Logging and accounting configuration for video statistics (classic CLI)
A:node-2>config>log# info
----------------------------------------------
        file-id 1
            location cf3:
        exit
        accounting-policy 1
            shutdown
            record video
            collection-interval 5
            to file 1
        exit
----------------------------------------------

The following example shows how to enable logging and accounting for a service to collect statistics for a particular service and video interface. This example refers to the accounting policy created in the preceding example. When administratively enabled, this starts recording of statistics. The statistics are written in an act-collect directory and administratively enabling the accounting policy moves the recorded file to the act directory.

Enabling video statistics collection for a service (MD-CLI)
[ex:/configure service ies "300"]
A:admin@node-2# info
    video-interface "vi" {
        admin-state enable
        accounting-policy 1 {
            admin-state enable
        }
    }
Enabling video statistics collection for a service (classic CLI)
A:node-2>config>service>ies# info
  video-interface "vi" create
        accounting-policy "1"
            no shutdown
        exit
        no shutdown
  exit