ISA and ESA hardware

In this section

This section provides an overview of Nokia’s implementation of the ISA and ESA hardware.

Note: Cards must be configured using the commands described in the 7450 ESS, 7750 SR, 7950 XRS, and VSR Interface Configuration Guide.
Note:

The following conditions apply to the ISA and ESA hardware:

  • ISAs (ISA2s alone or on MS-ISM cards) and ESA-VMs cannot be intermixed within the same ISA group. This limitation applies to all ISA group types.

  • All ISA group types allow ESA-VMs to be hosted on ESAs of any hardware version.

MS-ISA2 overview

The MS-ISA2 (or ISA2-MS in CLI) is a second generation Integrated Services Adapter for multiservice processing, as a resource module within the router system providing packet buffering and packet processing.

The MS-ISA2 fits in an MDA or ISA slot on an IOM4-e and has no external ports, so all communication passes through the Input/Output Module (IOM), making use of the network processor complex on the host IOM for queuing and filtering functions like other MDAs and ISAs.

The actual ingress and egress throughput varies depending on the buffering and processing demands of a specific application, but the MS-ISA2 hardware can support 40 Gb/s of throughput processing. The processed rate (up to 40 Gb/s) is the sum of the upstream and downstream rates (for example, 10 Gb/s up and 30 Gb/s down, or 20 Gb/s up and 20 Gb/s down).

MS-ISM overview

The Multiservice Integrated Services Module (MS-ISM) card contains two ISA2 processing modules providing increased packet processing throughput and scale compared to the MS-ISA platform. Each ISA2 processing module supports a 40G datapath for packet processing; as with ISA1 the actual throughput varies by function. The processed rate (up to 40 Gb/s) is the sum of the upstream and downstream rates (for example, 10 Gb/s up and 30 Gb/s down, or 20 Gb/s up and 20 Gb/s down).

The IOM base card is an imm-2pac-fp3 with two embedded positions for ISA2s. Hot swap or field replacement of the ISA2s within an MS-ISM assembly is not supported. IMM cards offering 10x10GE media plus one ISA2, or 1x100GE media plus one ISA2.

The following shows the ISA2 processing modules in the MG-ISM card.

Figure 1. MS-ISM with ISA2s

The MS-ISA2 remains as a common base hardware assembly to be used as a generic CPU processing platform for multiple applications. The functions supported on the MS-ISA2 and MS-ISM include the following software based capabilities:

  • Application Assurance (AA)

  • Tunnel (IPsec, GRE)

  • Broadband (NAT, LNS)

  • Video (FCC, RET)

ESA overview

An Extended Services Appliance (ESA) is a server that attaches to a host 7750 SR over standard SR system interface ports, and which has one to four Virtual Machine (VM) instances to perform multiservice processing. The ESA provides packet buffering and processing and is logically part of the router system. The ESA 100G-2 includes one 20-core Intel fourth generation (Sapphire Rapids) 4416+ processor and 128 Gbytes of memory. The ESA 400G (Revision BA) includes two 32-core Intel fourth generation (Sapphire Rapids) 6438N processors and 512 Gbytes of memory.

The ESA processing rate is the sum of the upstream and downstream rates (for example, 80 Gb/s up and 20 Gb/s down, or 50 Gb/s up and 50 Gb/s down).

The ESA 100G-2 hardware can support up to 100 Gb/s of throughput processing, and the ESA 400G up to 400 Gb/s of processing. However, the maximum ESA ingress and egress throughput varies depending on the buffering and processing demands of a specific application.

The following shows an ESA connected to a 7750 SR.

Figure 2. ESA connection to 7750 SR

A direct local fiber connection must be used to connect an ESA port to a 7750 SR port. As with other MDAs and ISAs, all communication passes through the 7750 SR Input/Output Module (IOM), making use of the network processor complex on the host IOM for queuing and filtering functions.

The ESA 100G-2 includes one Mellanox Connect X6 2-port 100 Gb/s NIC with QSFP28 optics connectors. Each NIC has a maximum 200 Gb/s throughput per NIC, but the CPU capacity of the ESA 100G-2 limits the number of useful links to one 100 Gb/s port. Either of the two ESA NIC ports can be used to connect to the 7750 SR port.

The ESA 400G includes two Mellanox Connect X6 2-port 100 Gb/s NIC with QSFP28 optics connectors. Each NIC has a maximum 200 Gb/s throughput per NIC, and any of the four ESA NIC ports can be used to connect to the 7750 SR port.

The following SR to ESA port speeds are supported:

  • 100GE (using QSFP28 optics in both the SR and ESA)

  • 40GE (using QSFP+ optics in both the SR and ESA)

  • 25GE (using a QSFP28 - SFP28/SFP+ Adapter and SFP28 optics in both SR and ESA)

  • 10GE (using a QSFP28 - SFP28/SFP+ Adapter and SFP+ optics in both SR and ESA)

ESA 400G performance may be enhanced by configuring up to four ESA VMs for a single ESA across two CPUs. The two ESA NICs each connect to only one NUMA cell (CPU socket). For each ESA VM, reserve at least one port for SR interconnect. The most common ESA 400G deployment scenarios are as follows:

  • one port and one ESA VM – one port per NIC and one ESA VM per CPU socket

  • two ports and two ESA VMs – one port per NIC and one ESA VM per CPU socket to ensure maximum port and ESA VM performance

  • four ports and four ESA VMs – two ports per NIC and two ESA VMs per CPU socket for maximum performance and density

Note: When using four ports and four ESA VMs, because each CPU socket is shared by two VMs, the throughput for each VM is slightly less than when one VM is used.

Ports for an ESA may be from the same or from different IOMs, XMAs, or MDAs. Any combination of supported port speeds may be used on an ESA. If at least one host-port between the SR and the ESA is up, the ESA instance stays up.

An ESA-VM must be associated with one specific 7750 SR port. One physical 7750 SR port can be used by multiple VMs within an ESA. ESA-VMs may be configured as different types or the same type.

As each ESA-VM may only be associated with one 7750 SR port, LAG cannot be used between ports to an ESA. ESA-to-SR link resilience is handled by provisioning more VM instances than the processing requires (using the ISA group N+1 redundancy model). Functional sparing capacity is also handled by provisioning more VM instances than required.

Each ESA is managed by one 7750 SR. The ESA software (hypervisors.tim file, located on the active CPM from the 7750 SR host) can only be instantiated by a 7750 SR and cannot be instantiated in any other virtualized environment. Creation, configuration, deletion, resource allocation, and upgrade of a ESA-VM are all controlled by the 7750 SR CPM.

SR system LLDP must be enabled for ESA use, as LLDP is used to verify connectivity between the configured SR ESA host-ports and the matching configured ESA port for an ESA-VM. To set up an ESA in a 7750 SR system, complete the following actions in any order:

  • Install the ESA hardware in a rack, then apply power to the ESA hardware.

  • Connect the ESA hardware to a compatible 7750 SR chassis, IOM, or MDA using the appropriate optics.

  • From the 7750 SR, configure ESA host and ESA-VM ports; see Configuring an ESA with CLI.

See the 7750 SR ESA Chassis Installation Guide for more information about the first two items in the preceding list.

Note: After the ESA host-port is assigned, the port defaults are automatically modified. The new port defaults cannot be changed by the operator until the port is unassigned as an ESA host-port.

The ESA hardware is then booted by the 7750 SR CPM and available resources are discovered by the 7750 SR. ESA-VMs are configured as a type and size (number of cores and amount of memory). ESA-VM types include services that also run on ISAs, thereby providing a virtualized ISA function as an ESA-VM within the SR system and as part of an ISA group. An ISA group can only contain physical ISAs or ESA-VMs. Traffic for an ESA-VM enters the 7750 SR and is forwarded to the ESA-VM in a manner identical to that of a traditional ISA.

Multiple ESAs may be configured per IOM and per system as needed for scale.

ESA 100G-2 and 400G provide CLI, SNMP, and YANG support for the following hardware monitoring states:

  • ESA health – unknown, OK, degraded, or critical

  • PSU health – unknown, OK, degraded, or critical

  • Fan redundancy – unknown, redundant, non-redundant, or failed-redundant

  • Fan health – unknown, OK, degraded, or critical

  • Power supply mismatch – true or false

  • Power supply redundancy – unknown, redundant, non-redundant, or failed-redundant

  • Temperature health – unknown, OK, degraded, or critical

ESA hardware monitoring events and states are integrated into the SR OS system facility alarms.

Application Assurance hardware features

AA system support

The Application Assurance Integrated Services Adapter (AA ISA) is a resource adapter, which means that there are no external interface ports on the AA ISA itself. Similarly, ESAs only do processing functions for traffic on the ESA interconnect ports to the SR system. Traffic on the SR system is forwarded to ISAs or ESA from any other IOMs on a system in which the AA ISA or ESA is installed, with a divert mechanism used to switch traffic internally to the AA ISA or ESA-VM.

See the SR OS R23.x.Rx Software Release Notes for information about the ESA platform support.

The following table describes Application Assurance support on the 7750 SR and 7450 ESS.

Table 1. AA system support
System AA on MS-ISM AA on MS-ISA2

7750 SR-12

Yes

Yes

7750 SR-12e

Yes

Yes

7750 SR-7

Yes

Yes

7750 SR-1e

No

Yes

7750 SR-2e

No

Yes

7750 SR-3e

No

Yes

7450 ESS-12

Yes

Yes

7450 ESS-7

Yes

Yes

Host IOM support for AA on ISAs

The AA MS-ISA2 is supported on IOM4-e, IOM4-e-B, IOM4-e-HS, and on 7750 SR-1e, 7750 SR-2e, and 7750 SR-3e (IOM-e). The MS-ISM versions contain one or two ISA2s embedded on a IMM card.

Each IOM can support a maximum of two AA ISA2 modules. To maximize AA ISA redundancy, deployment of AA ISAs on separate host IOMs is recommended as it provides IOM resilience. Traffic from any supported IOM (for example, IOM4-e, a fixed port IOM (IMM)) can be diverted to an AA ISA host IOM.

The MS-ISA2 is field replaceable and supports hot insertion and removal. An SR system can support up to 15 active ISA2s for AA, each providing up to 40 Gb/s processing and 600 Gb/s total per system.

AA ISA software upgrades are part of the ISSU functionality. Upgrades to AA ISA software, for example to activate new protocol signatures, do not impact the second MDA slot for the IOM carrying the AA ISA, nor do upgrades impact the router itself (for example a new AA ISA software image can be downloaded without a need to upgrade other software images).

Host IOM support for AA on ESAs

ESA port connectivity is supported on most FP3-based IOMs and all FP4-based (or later) cards. For a list of supported platforms or cards, contact your Nokia representative.

An SR system can support up to 15 active and one standby ESA-VMs for AA.

AA ESA-VM software upgrades are part of the ISSU functionality. Upgrades to AA software, for example to activate new protocol signatures, do not impact other ESA-VMs on the same ESA or on other traffic on the same IOM, nor do upgrades impact the router itself (for example, a new AA software image can be downloaded to an ESA-VM without a need to upgrade other software images).

The ESA version must match the build release version of the host IOM.

Configuring an ESA with CLI

This section provides information to configure an ESA using the command line interface from a 7750 SR. It is assumed that the user is familiar with the basic concepts of configuring policies.

Provisioning an ESA and ESA-VM

Use the following syntax to provision an ESA.

Note: Each ESA host-port and ESA-VM port must each be associated with a dedicated 7750 SR 100G port.
config>esa esa-id
    vm vm-id
        vm-type {aa | bb | tunnel | video}

The following example shows an ESA containing both a VM-type AA and a VM-type BB.

configure 
            esa 1 create 
                description "Esa for AA-BB" 
                host-port 7/1/c6/1 
                vm 1 create 
                    description "Application-Assurance ISA" 
                    vm-type aa 
                    host-port 7/1/c6/1
                    cores 12 
                    memory 20  
                    no shutdown 
                exit 
                vm 2 create 
                    description "Broadband ISA" 
                    vm-type bb 
                    host-port 7/1/c6/1 
                    cores 9 
                    memory 40
                    no shutdown 
                exit 

The following output displays an ESA and ESA-VM for the preceding configuration example.

show esa 
========================================================================= 
Extended Services Appliance Summary 
========================================================================= 
ESA  Description                                           Admin     Oper 
                                                           State     State 
-------------------------------------------------------------------------- 
1                                                           up        up 
========================================================================== 
 
show esa detail 
=============================================================================== 
ESA 1 
=============================================================================== 
Description                  : Esa for AA-BB 
Admin State                  : up 
Operational State            : up 
Oper flags                   : none 
IOM Host Port                : 7/1/c6/1 
Hardware Data 
    System manufacturer      : Nokia Solutions and Networks 
    System product name      : ESA-100G 
    System serial number     : QTFCT99040103 
    Software Version         : TiMOS-H-19.10.S24 hypervisor/esa Copyright (c) 
                               2000-2019 Nokia. All rights reserved. All use 
                               subject to applicable license agreements. Built 
                               on Wed Oct 23 20:35:01 PDT 2019 by builder in / 
                               builds/c/1910S/S24/panos/hypervisors 
    Time of last boot        : 2019/10/24 14:49:58 UTC 
    Cores available          : 23 
    Cores allocated          : 23 
    Cores remaining          : 0 
    Memory available         : 192 GB 
    Memory allocated         : 60 GB 
    Memory remaining         : 132 GB 
    Performance enabled      : yes 
    Export restricted        : no 
=========================================================================