j Commands

jitter-event

Syntax

jitter-event rising-threshold threshold [falling-threshold threshold] [direction]

no jitter-event

Context

[Tree] (config>saa>test jitter-event)

Full Context

configure saa test jitter-event

Description

This command specifies that at the termination of an SAA test probe, the calculated jitter value is evaluated against the configured rising and falling jitter thresholds. SAA threshold events are generated as required.

Once the threshold (rising/falling) is crossed, it is disabled from generating additional events until the opposite threshold is crossed. If a falling-threshold is not supplied, the rising- threshold is re-enabled when it falls below the threshold after the initial crossing that generated the event.

The configuration of jitter event thresholds is optional.

The no form of the command disables the jitter event.

Parameters

rising-threshold threshold

Specifies a rising threshold jitter value, in milliseconds. When the test run is completed, the calculated jitter value is compared to the configured jitter rising threshold. If the test run jitter value is greater than the configured rising threshold value then an SAA threshold event is generated. The SAA threshold event is tmnxOamSaaThreshold, logger application OAM, event #2101.

Values: 0 to 2147483

Default: 0

falling-threshold threshold

Specifies a falling threshold jitter value, in milliseconds. When the test run is completed, the calculated jitter value is compared to the configured jitter falling threshold. If the test run jitter value is greater than the configured falling threshold value then an SAA threshold event is generated. The SAA threshold event is tmnxOamSaaThreshold, logger application OAM, event #2101.

Values: 0 to 2147483

Default: 0

direction

Specifies the direction for OAM ping responses received for an OAM ping test run.

Values

inbound — Monitor the value of jitter calculated for the inbound, one-way, OAM ping responses received for an OAM ping test run.

outbound — Monitor the value of jitter calculated for the outbound, one-way, OAM ping requests sent for an OAM ping test run.

roundtrip — Monitor the value of jitter calculated for the round trip, two-way, OAM ping requests and replies for an OAM ping test run.

Default: roundtrip

Platforms

All

join-time

Syntax

join-time value

no join-time

Context

[Tree] (config>service>vpls>sap>mrp join-time)

[Tree] (config>service>vpls>spoke-sdp>mrp join-time)

[Tree] (config>service>vpls>mesh-sdp>mrp join-time)

Full Context

configure service vpls sap mrp join-time

configure service vpls spoke-sdp mrp join-time

configure service vpls mesh-sdp mrp join-time

Description

This command controls the interval between transmit opportunities that are applied to the Applicant state machine. An instance of this Join Period Timer is required on a per-Port, per-MRP Participant basis. For additional information, refer to IEEE 802.1ak-2007 section 10.7.4.1.

Default

join-time 2

Parameters

value

The interval between transmit opportunities, in tenths of a second.

Values: 1 to 10

Platforms

All

join-tlv-packing-disable

Syntax

[no] join-tlv-packing-disable

Context

[Tree] (config>service>vprn>mvpn>pt>selective join-tlv-packing-disable)

Full Context

configure service vprn mvpn provider-tunnel selective join-tlv-packing-disable

Description

This command enables packing of MDT join TLVs into a single PDU to improve efficiency, if multiple join TLVs are available at the time of transmission.

The no form of this command disables packing of MDT join TLVs into a single PDU.

Default

no join-tlv-packing-disable

Platforms

All

jp

Syntax

jp [group grp-ip-address] [ source ip-address] [detail]

no jp

Context

[Tree] (debug>service>id>pim-snooping jp)

Full Context

debug service id pim-snooping jp

Description

This command enables or disables debugging for the PIM Join-Prune mechanism.

Parameters

grp-ip-address

Debugs information associated with the specified Join-Prune mechanism.

Values: multicast group address (ipv4 or ipv6) or zero

ip-address

Debugs information associated with the specified Join-Prune mechanism

Values: source IP address (IPv4 or IPv6)

detail: Debugs detailed Join-Prune mechanism information

Platforms

All

jp

Syntax

jp [group grp-ip-address] [source ip-address] [detail]

no jp

Context

[Tree] (debug>router>pim jp)

Full Context

debug router pim jp

Description

This command enables debugging for PIM join and prune mechanisms.

The no form of this command disables PIM join and prune mechanisms debugging.

Parameters

grp-ip-address

Debugs information associated with the specified Join-Prune mechanism.

Values: multicast group address (ipv4, ipv6) or zero

ip-address

Debugs information associated with the specified Join-Prune mechanism.

Values: source address (ipv4, ipv6)

detail: Debugs detailed Join-Prune mechanism information.

Platforms

All