Getting started

About this guide

This guide describes details pertaining to Triple Play Services Delivery Architecture (TPSDA) support provided by the operating system and presents examples to configure and implement various protocols and services.

This guide is organized into functional chapters and provides concepts and descriptions of the implementation flow, as well as Command Line Interface (CLI) syntax and command usage.

Note: Unless otherwise indicated, this guide uses classic CLI command syntax and configuration examples.

The topics and commands described in this document apply to the:

  • 7450 ESS

  • 7750 SR

  • Virtualized Service Router

For a list of unsupported features by platform and chassis, see the SR OS R23.x.Rx Software Release Notes, part number 3HE 19269 000 x TQZZA.

Command outputs shown in this guide are examples only; actual displays may differ depending on supported functionality and user configuration.

Note: The SR OS CLI trees and command descriptions can be found in the following guides:
  • 7450 ESS, 7750 SR, 7950 XRS, and VSR Classic CLI Command Reference Guide

  • 7450 ESS, 7750 SR, 7950 XRS, and VSR Clear, Monitor, Show, and Tools Command Reference Guide (for both MD-CLI and Classic CLI)

  • 7450 ESS, 7750 SR, 7950 XRS, and VSR MD-CLI Command Reference Guide

Note: This guide generically covers Release 23.x.Rx content and may contain some content to be released in later maintenance loads. See the SR OS R23.x.Rx Software Release Notes, part number 3HE 19269 000 x TQZZA, for information about features supported in each load of the Release 23.x.Rx software.

Nokia SR OS services configuration process

Configuration process lists the tasks necessary to configure TPSDA entities. Each section describes a software area and provides CLI syntax and command usage to configure parameters for a functional area.

Table 1. Configuration process
Area Task Section

Triple play services

Provision and deploy services

Deploying and provisioning services

Configure triple play services

Configuring Triple Play services with CLI

Protocol configuration

Configure DHCP

Configuring DHCP with CLI

Configure traffic steering on L2TP LAC

Configuring traffic steering on L2TP LAC

PPPoE

Configure point-to-point over Ethernet

Point-to-Point Protocol over Ethernet management

Security

Configure triple play security

Configuring Triple Play security with CLI

Multicast

Configure triple play multicast services

Configuring Triple Play multicast services with CLI

Enhanced Subscriber management

Configure RADIUS server

Uniform RADIUS server configuration

Use scripts dynamic recognition of subscribers

Using scripts for dynamic recognition of subscribers

Configure IP and IPv6 filter policies for subscriber hosts

Configuring IP and IPv6 filter policies for subscriber hosts

Configure Dual-Stack Lite (SD-Lite)

Dual-Stack Lite

Configure MSAP

MSAP QoS configuration

Configure web authentication protocol (WPP)

WPP configurations

Configure IPoE session

Configuration steps

Troubleshoot ESM

ESM troubleshooting show command

Configure enhanced subscriber management

Configuring ESM with CLI

Deploy oversubscribed multi-chassis redundancy

Deploying oversubscribed multi-chassis redundancy

Python Scripting

Python script support for ESM

Conventions

This section describes the general conventions used in this guide.

Precautionary and information messages

The following information symbols are used in the documentation.

DANGER: Danger warns that the described activity or situation may result in serious personal injury or death. An electric shock hazard could exist. Before you begin work on this equipment, be aware of hazards involving electrical circuitry, be familiar with networking environments, and implement accident prevention procedures.
WARNING: Warning indicates that the described activity or situation may, or will, cause equipment damage, serious performance problems, or loss of data.
Caution: Caution indicates that the described activity or situation may reduce your component or system performance.
Note: Note provides additional operational information.
Tip: Tip provides suggestions for use or best practices.

Options or substeps in procedures and sequential workflows

Options in a procedure or a sequential workflow are indicated by a bulleted list. In the following example, at step 1, the user must perform the described action. At step 2, the user must perform one of the listed options to complete the step.

Options in a procedure

  1. User must perform this step.
  2. This step offers three options. User must perform one option to complete this step.
    • This is one option.
    • This is another option.
    • This is yet another option.

Substeps in a procedure or a sequential workflow are indicated by letters. In the following example, at step 1, the user must perform the described action. At step 2, the user must perform two substeps (a. and b.) to complete the step.

Substeps in a procedure

  1. User must perform this step.
  2. User must perform all substeps to complete this action.
    1. This is one substep.
    2. This is another substep.