x Commands

Context

[Tree] (config>li x-interfaces)

Full Context

configure li x-interfaces

Description

Commands in this context configure LI X1, X2, and X3 interfaces.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>li>x-interfaces x1)

Full Context

configure li x-interfaces x1

Description

Commands in this context configure the LI X1 interface.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>li>x-interfaces x2)

Full Context

configure li x-interfaces x2

Description

Commands in this context configure the LI X2 interface.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (config>li>x-interfaces x3)

Full Context

configure li x-interfaces x3

Description

Commands in this context configure the LI X3 interface.

Platforms

7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS

Context

[Tree] (debug>router>mpls>event xc)

Full Context

debug router mpls event xc

Description

This command debugs cross connect events.

The no form of the command disables the debugging.

Parameters

detail

Displays detailed information about cross connect events.

Platforms

All

Context

[Tree] (config>subscr-mgmt>wlan-gw>tunnel-query>ue-state xcon)

Full Context

configure subscriber-mgmt wlan-gw tunnel-query ue-state xcon

Description

This command enables matching on tunnels with cross-connect UEs.

The no form of this command disables matching on cross-connect UEs, unless UE state matching is disabled altogether.

Default

no xcon

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>service>ies>sub-if>grp-if>wlan-gw>vlan-tag-ranges>range xconnect)

[Tree] (config>router>wlan-gw xconnect)

[Tree] (config>service>vprn>sub-if>grp-if>wlan-gw>vlan-tag-ranges>range xconnect)

Full Context

configure service ies subscriber-interface group-interface wlan-gw vlan-tag-ranges range xconnect

configure router wlan-gw xconnect

configure service vprn subscriber-interface group-interface wlan-gw vlan-tag-ranges range xconnect

Description

Commands in this context configure WLAN-GW cross-connect UE-related parameters.

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>card>mda xconnect)

[Tree] (config>card>xiom>mda xconnect)

Full Context

configure card mda xconnect

configure card xiom mda xconnect

Description

This command creates a loopback (cross-connect) in the MAC chip and does not require a faceplate port.

Platforms

7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS

• configure card mda xconnect

7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s

• configure card xiom mda xconnect

Context

[Tree] (config>subscr-mgmt>auth-plcy>include xconnect-tunnel-home-address)

[Tree] (config>subscr-mgmt>acct-plcy>include-radius-attribute xconnect-tunnel-home-address)

Full Context

configure subscriber-mgmt authentication-policy include-radius-attribute xconnect-tunnel-home-address

configure subscriber-mgmt radius-accounting-policy include-radius-attribute xconnect-tunnel-home-address

Description

This command enables the generation of the Cross Connect Tunnel Home Address RADIUS attribute.

The no form of the command reverts to the default value.

Default

no xconnect-tunnel-home-address

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>isa-radius-plcy>acct-include-attributes xconnect-tunnel-home-address)

[Tree] (config>aaa>isa-radius-plcy>auth-include-attributes xconnect-tunnel-home-address)

Full Context

configure aaa isa-radius-policy acct-include-attributes xconnect-tunnel-home-address

configure aaa isa-radius-policy auth-include-attributes xconnect-tunnel-home-address

Description

This command enables the cross connect tunnel home address RADIUS attribute.

Default

no xconnect-tunnel-home-address

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>isa-radius-plcy>acct-include-attributes xconnect-tunnel-local-ipv6-address)

Full Context

configure aaa isa-radius-policy acct-include-attributes xconnect-tunnel-local-ipv6-address

Description

This command enables the generation of the cross connect tunnel local IPv6 address RADIUS attribute.

Default

no xconnect-tunnel-local-ipv6-address

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>isa-radius-plcy>acct-include-attributes xconnect-tunnel-remote-ipv6-address)

Full Context

configure aaa isa-radius-policy acct-include-attributes xconnect-tunnel-remote-ipv6-address

Description

This command enables the generation of the cross connect tunnel remote IPv6 address RADIUS attribute.

Default

no xconnect-tunnel-remote-ipv6-address

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>isa-radius-plcy>acct-include-attributes xconnect-tunnel-service)

Full Context

configure aaa isa-radius-policy acct-include-attributes xconnect-tunnel-service

Description

This command enables the generation of the cross connect tunnel service RADIUS attribute.

Default

no xconnect-tunnel-service

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>aaa>isa-radius-plcy>acct-include-attributes xconnect-tunnel-type)

Full Context

configure aaa isa-radius-policy acct-include-attributes xconnect-tunnel-type

Description

This command enables the generation of the cross connect tunnel type RADIUS attribute.

Default

no xconnect-tunnel-type

Platforms

7750 SR, 7750 SR-e, 7750 SR-s, VSR

Context

[Tree] (config>port>ethernet xgig)

Full Context

configure port ethernet xgig

Description

This command configures a 10 Gb/s interface to be in Local or Wide Area Network (LAN or WAN) mode. When configuring the port to be in WAN mode certain SONET/SDH parameters can be changed to reflect the SONET/SDH requirements for this port.

When the port is configured for LAN mode, all SONET/SDH parameters are pre-determined and not configurable.

Default

xgig lan

Parameters

lan

Sets the port to operate in LAN mode.

wan

Sets the port to operate in WAN mode.

Platforms

All

Context

[Tree] (config>card xiom)

Full Context

configure card xiom

Description

This command configures an XIOM in one of the slots of an XCM. An XIOM can be used instead of an XMA and operates as a carrier module to support MDA-s modules.

Parameters

xiom-slot

Specifies the XIOM identifier.

Values

x1 or x2

Platforms

7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s

Context

[Tree] (config>card>xiom xiom-type)

Full Context

configure card xiom xiom-type

Description

This command adds an XIOM to the device configuration for the slot. The XIOM type can be preprovisioned, which means that the XIOM does not have to be installed in the chassis.

An XIOM must be provisioned before an MDA-s, connector, or port can be configured.

An XIOM can only be provisioned in a slot that is vacant. No other XIOM or XMA can be provisioned (configured) for that particular slot. To reconfigure a slot position, use the no form of this command to remove the current information.

An XIOM can only be provisioned in a slot if the XIOM type is allowed in the slot. An error message is generated if an attempt is made to provision an XIOM type that is not allowed.

If an XIOM is inserted that does not match the configured XIOM type for the slot, then a log event and a facility alarm are raised. The alarm is cleared when the correct XIOM type is installed or the configuration is modified.

A log event and a facility alarm are raised if an administratively enabled XIOM is removed from the chassis. The alarm is cleared when the correct XIOM type is installed or the configuration is modified. A log event is issued when a XIOM is removed that is administratively disabled.

XIOMs are controlled by hardware and software licensing. For these cards, the license level must be provisioned in addition to the XIOM type. An XIOM cannot become operational unless the provisioned license level matches the license level of the card installed into the slot. The set of license levels varies by XIOM type.

The provisioned license level controls aspects related to connector provisioning and the consumption of hardware egress queues and egress policers. Changes to the provisioned license level may be blocked if a configuration exists that would not be permitted with the new target license level.

If the license level is not specified, the level is set to the highest license level for that XIOM.

The no form of this command removes the XIOM from the configuration.

Parameters

xiom-type

Specifies the type of XIOM to be configured and installed in the slot. Values for this attribute vary by platform and release. The release notes include a listing of all supported xiom-types and their CLI strings. In addition, the command can be queried to check which xiom-types are relevant for the active platform type.

xiom-level

Specifies the license level of the XIOM, up to 32 characters. Possible values vary by XIOM type.

Platforms

7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s