p Commands
p2mp
p2mp
Syntax
p2mp p2mp-id identifier root ip-address [ session ip-addr [label-space]] [summary | detail]
p2mp p2mp-id identifier root ip-address [ session ip-addr [label-space]] [summary | detail] inner-root ip-address
p2mp p2mp-id identifier [rd rd] [ session ip-addr [label-space]] [family] [ summary | detail] [innermost-root ip-address]
p2mp p2mp-id identifier root ip-address rd rd [session ip-addr [ label-space] [family] [summary | detail] [innermost-root ip-address]
p2mp [session ip-addr [label-space]] [ family] [summary | detail] [opaque-type opaque-type]
p2mp source ip-address group mcast-address root ip-address [session ip-addr [ label-space]] [family] [summary | detail] inner-root ip-address
p2mp source ip-address group mcast-address root ip-address [rd rd] [ session ip-addr [label-space]] [summary | detail]
p2mp source ip-address group mcast-address [ session ip-addr [label-space]] [family] [ summary | detail] [innermost-root ip-address]
p2mp stitching [p2mp-id identifier root ip-address [rd rd] [ inner-root ip-address]]
p2mp stitching source ip-address group mcast-address root ip-address inner-root ip-address
p2mp stitching p2mp-id identifier [rd rd] innermost-root ip-address
p2mp stitching source ip-address group mcast-address innermost-root ip-address
Context
[Tree] (show>router>ldp>bindings p2mp)
Full Context
show router ldp bindings p2mp
Description
This command displays LDP P2MP FEC bindings.
Parameters
- detail
-
Displays detailed information.
- family
-
Displays either IPv4 or IPv6 active LDP information.
- group mcast-address
-
Displays the P2MP group multicast address bindings.
- inner-root ip-address
-
Displays recursive FECs whose inner root address matches the specified address.
- innermost-root ip-address
-
Displays recursive FECs whose inner root address matches the specified address and non-recursive FECs that have a root address that matches the specified address.
- opaque-type opaque-type
-
Specifies the type of a Multi-Point Opaque Value Element.
- p2mp-id identifier
-
Displays LDP active P2MP identifier bindings.
- rd rd
-
Displays information for the route distinguisher.
- root ip-address
-
Displays root IP address information.
- session ip-addr[label-space]
-
Displays information for the LDP session IP address and label space.
- source ip-address
-
Displays LDP active P2MP source bindings.
- stitching
-
Displays stitching information for LDP P2MP FEC bindings.
- summary
-
Displays information in a summarized format.
Platforms
All
Output
Output ExampleThe following show output displays recursive FECs.
A:Dut-C# show router ldp bindings p2mp stitching
===============================================================================
LDP GRT Recursive with Generic IPv4 P2MP Bindings
===============================================================================
RootAddr
InnerRootAddr P2MP-Id Stitch
-------------------------------------------------------------------------------
10.20.1.3
10.20.1.5 8193 lowerFec
10.180.5.5
10.20.1.5 8193 primUpperFec
10.181.5.5
10.20.1.5 8193 bkpUpperFec
-------------------------------------------------------------------------------
10.20.1.3
10.20.1.6 8193 lowerFec
10.180.5.5
10.20.1.6 8193 primUpperFec
10.181.5.5
10.20.1.6 8193 bkpUpperFec
-------------------------------------------------------------------------------
10.180.5.3
10.20.1.1 8193 lowerFec
10.20.1.1
-- 8193 primUpperFec
-------------------------------------------------------------------------------
10.180.5.3
10.20.1.2 8193 lowerFec
10.20.1.2
-- 8193 primUpperFec
-------------------------------------------------------------------------------
No. of GRT Recursive with Generic IPv4 P2MP Bindings: 10
===============================================================================
A:Dut-C# show router ldp bindings active p2mp
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, BA - ASBR Backup FEC
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
8193 73730
10.20.1.1 Pop 262134 --
-- --
8193 73730
10.20.1.1 (UF) Swap 262134 Stitched
-- --
8193 73729
10.20.1.2 Pop 262135 --
-- --
8193 73729
10.20.1.2 (UF) Swap 262135 Stitched
-- --
8193 73728
10.20.1.3 Push -- 262137
10.180.2.1 1/1/1:0
8193 73728
10.20.1.3 Push -- 262137
10.181.2.1 1/1/1:1
-------------------------------------------------------------------------------
No. of Generic IPv4 P2MP Active Bindings: 6
===============================================================================
===============================================================================
LDP GRT Recursive with Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
InnerRootAddr
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
8193 Unknw
10.20.1.3 (LF) Push -- 262135
10.20.1.5
10.180.2.1 1/1/1:0
8193 Unknw
10.20.1.3 (LF) Push -- 262135
10.20.1.5
10.181.2.1 1/1/1:1
8193 Unknw
10.20.1.3 (LF) Push -- 262136
10.20.1.6
10.180.2.1 1/1/1:0
8193 Unknw
10.20.1.3 (LF) Push -- 262136
10.20.1.6
10.181.2.1 1/1/1:1
8193 Unknw
10.180.5.3 (LF) Push -- 262132
10.20.1.1
10.180.5.5 2/1/1:0
8193 Unknw
10.180.5.3 (LF) Push -- 262136
10.20.1.2
10.180.5.5 2/1/1:0
8193 Unknw
10.180.5.3 Push -- 262131
10.20.1.3
10.180.5.5 2/1/1:0
8193 73731
10.180.5.5 Pop 262126 --
10.20.1.5
-- --
8193 73731
10.180.5.5 (UF) Swap 262126 Stitched
10.20.1.5
-- --
8193 73732
10.180.5.5 Pop 262124 --
10.20.1.6
-- --
8193 73732
10.180.5.5 (UF) Swap 262124 Stitched
10.20.1.6
-- --
8193 73731
10.181.5.5 (BA) Pop 262125 --
10.20.1.5
-- --
8193 73731
10.181.5.5 (BA) (UF) Swap 262125 Stitched
10.20.1.5
-- --
8193 73732
10.181.5.5 (BA) Pop 262123 --
10.20.1.6
-- --
8193 73732
10.181.5.5 (BA) (UF) Swap 262123 Stitched
10.20.1.6
-- --
-------------------------------------------------------------------------------
No. of GRT Recursive with Generic IPv4 P2MP Active Bindings: 15
===============================================================================
p2mp
Syntax
p2mp p2mp-id identifier root ip-address [summary | detail] [egress-if port-id]
p2mp p2mp-id identifier root ip-address [summary | detail] [egress-lsp tunnel-id]
p2mp p2mp-id identifier root ip-address [summary | detail] [egress-nh ip-address]
p2mp [family] [summary | detail] [ egress-if port-id] [opaque-type opaque-type]
p2mp [family] [summary | detail] [ egress-lsp tunnel-id] [opaque-type opaque-type]
p2mp [family] [summary | detail] [ egress-nh ip-address] [opaque-type opaque-type]
p2mp p2mp-id identifier root ip-address [rd rd] [summary | detail] [ egress-if port-id] inner-root ip-address
p2mp p2mp-id identifier root ip-address [rd rd] [summary | detail] [ egress-lsp tunnel-id] inner-root ip-address
p2mp p2mp-id identifier root ip-address [rd rd] [summary | detail] [ egress-nh ip-address] inner-root ip-address
p2mp source ip-address group mcast-address root ip-address [summary | detail] [egress-if port-id] inner-root ip-address
p2mp source ip-address group mcast-address root ip-address [summary | detail] [ egress-lsp tunnel-id] inner-root ip-address
p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [egress-if port-id]
p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [egress-lsp tunnel-id]
p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [egress-nh ip-address]
p2mp p2mp-id identifier [rd rd] [family] [summary | detail] [ innermost-root ip-address]
p2mp source ip-address group mcast-address [family] [summary | detail] [ innermost-root ip-address]
Context
[Tree] (show>router>ldp>bindings>active p2mp)
Full Context
show router ldp bindings active p2mp
Description
This command displays LDP active P2MP bindings.
Parameters
- identifier
-
Specifies the P2MP ID.
- ip-address
-
Specifies the IPv4 or IPv6 address.
- mcast-address
-
Displays the P2MP group multicast address bindings.
- rd
-
Displays information for the route distinguisher.
- family
-
Specifies the address family.
- port-id
-
Specifies the port ID.
- tunnel-id
-
Specifies the tunnel ID.
- opaque-type
-
Specifies the multi-point opaque value element type.
Platforms
All
p2mp-candidate-path
p2mp-candidate-path
Syntax
p2mp-candidate-path [path-name] [oper { up | down}] [in-use]
Context
[Tree] (show>router>p2mp-sr-tree>p2mp-policy p2mp-candidate-path)
Full Context
show router p2mp-sr-tree p2mp-policy p2mp-candidate-path
Description
This command displays candidate path information.
Parameters
- path-name
-
Specifies the candidate path name, up to 32 characters.
- oper up
-
Displays the candidate paths with operational status up.
- oper down
-
Displays the candidate paths with operational status down.
- in-use
-
Displays candidate paths that are in use.
Platforms
All
p2mp-info
p2mp-info
Syntax
p2mp-info [type {originate | transit | terminate}] [s2l-endpoint ip-address]
Context
[Tree] (show>router>mpls p2mp-info)
Full Context
show router mpls p2mp-info
Description
This command displays P2MP cross-connect information.
Parameters
- type
-
Specifies the P2MP type.
Platforms
All
Output
The following output is an example of MPLS p2mp information.
Output Example*A:Dut-C# show router mpls p2mp-info
========================================================================
MPLS P2MP Cross Connect Information
========================================================================
------------------------------------------------------------------------
S2L ipmsi-4000-73729::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.1 Tunnel ID : 61441
P2MP ID : 4000 Lsp ID : 29696
S2L Name : ipmsi-4000-73729::pa* To : 10.20.1.3
In Interface : 1/1/1 In Label : 262129
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-65535-73730::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.1 Tunnel ID : 61442
P2MP ID : 65535 Lsp ID : 30208
S2L Name : ipmsi-65535-73730::p* To : 10.20.1.3
In Interface : 1/1/1 In Label : 262128
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-1001-73728::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.1 Tunnel ID : 61440
P2MP ID : 1001 Lsp ID : 35840
S2L Name : ipmsi-1001-73728::pa* To : 10.20.1.3
In Interface : 1/1/1 In Label : 262127
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-1001-73732::path_ipmsi
-----------------------------------------------------------------------
Source IP Address : 10.20.1.2 Tunnel ID : 64944
P2MP ID : 1001 Lsp ID : 34816
S2L Name : ipmsi-1001-73732::pa* To : 10.20.1.3
In Interface : 1/1/2 In Label : 262114
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-4000-73729::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61441
P2MP ID : 4000 Lsp ID : 16384
S2L Name : ipmsi-4000-73729::pa* To : 10.20.1.1
Out Interface : 1/1/1 Out Label : 262131
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-4000-73729::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61441
P2MP ID : 4000 Lsp ID : 16384
S2L Name : ipmsi-4000-73729::pa* To : 10.20.1.4
Out Interface : 2/1/1 Out Label : 262121
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-1001-73728::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61440
P2MP ID : 1001 Lsp ID : 22016
S2L Name : ipmsi-1001-73728::pa* To : 10.20.1.1
Out Interface : 1/1/1 Out Label : 262129
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-1001-73728::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61440
P2MP ID : 1001 Lsp ID : 22016
S2L Name : ipmsi-1001-73728::pa* To : 10.20.1.2
Out Interface : 1/1/2 Out Label : 262115
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-1001-73728::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61440
P2MP ID : 1001 Lsp ID : 22016
S2L Name : ipmsi-1001-73728::pa* To : 10.20.1.4
Out Interface : 2/1/1 Out Label : 262108
Num. of S2ls : 2
------------------------------------------------------------------------
S2L ipmsi-1001-73728::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61440
P2MP ID : 1001 Lsp ID : 22016
S2L Name : ipmsi-1001-73728::pa* To : 10.20.1.5
Out Interface : 2/1/1 Out Label : 262108
Num. of S2ls : 2
------------------------------------------------------------------------
S2L ipmsi-65535-73730::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61442
P2MP ID : 65535 Lsp ID : 46592
S2L Name : ipmsi-65535-73730::p* To : 10.20.1.1
Out Interface : 1/1/1 Out Label : 262130
Num. of S2ls : 1
------------------------------------------------------------------------
S2L ipmsi-65535-73730::path_ipmsi
------------------------------------------------------------------------
Source IP Address : 10.20.1.3 Tunnel ID : 61442
P2MP ID : 65535 Lsp ID : 46592
S2L Name : ipmsi-65535-73730::p* To : 10.20.1.4
Out Interface : 2/1/1 Out Label : 262109
Num. of S2ls : 1
------------------------------------------------------------------------
P2MP Cross-connect instances : 12
p2mp-lsp
p2mp-lsp
Syntax
p2mp-lsp [lsp-name] [detail]
p2mp-lsp [lsp-name] p2mp-instance [p2mp-instance-name] [ mbb]
p2mp-lsp [lsp-name] p2mp-instance [p2mp-instance-name] s2l [s2l-name [to s2l-to-address]] [ status {up | down}] [detail]
p2mp-lsp [lsp-name] p2mp-instance [p2mp-instance-name] s2l [s2l-name [to s2l-to-address]] mbb
Context
[Tree] (show>router>mpls p2mp-lsp)
Full Context
show router mpls p2mp-lsp
Description
This command displays MPLS P2MP LSP information.
Parameters
- lsp-name
-
Specifies the LSP name, up to 64 characters, used in the path.
- p2mp-instance [p2mp-instance-name
-
Specifies the administrative name for the P2MP instance which must be unique within a virtual router instance.
- mbb
-
Specifies to display make-before-break (MBB) information.
- s2l
-
Specifies the source-to-leaf (S2L) name.
- to s2l-to-address
-
Indicates the IP address of the destination address of the S2L sub-LSP.
- status
-
Displays the status of the p2mp LSP.
Platforms
All
Output
The following output is an example of MPLS p2mp LSP information.
Output Example*A:Dut-C# show router mpls p2mp-lsp
- p2mp-lsp [<lsp-name>] [detail]
- p2mp-lsp [<lsp-name>] p2mp-instance [<p2mp-instance-name>] [mbb]
- p2mp-lsp [<lsp-name>] p2mp-instance [<p2mp-instance-name>] s2l [<s2l-name>
[to <s2l-to-address>]][status {up | down}] [detail]
- p2mp-lsp [<lsp-name>] p2mp-instance [<p2mp-instance-name>] s2l [<s2l-name>
[to <s2l-to-address>]] <mbb>
- p2mp-lsp using-template [lsp-template <template-name>] [detail]
<lsp-name> : [64 chars max] - accepts * as wildcard char
<p2mp-instance> : keyword
<p2mp-instance-name> : [max 32 chars]
<s2l> : keyword
<s2l-name> : [max 32 chars]
<up | down> : keywords
<detail> : keyword
<mbb> : keyword
<s2l-to-address> : [a.b.c.d]
<using-template> : keyword
<lsp-template> : [32 chars max]
*A:Dut-C# show router mpls p2mp-lsp
==============================================================================
MPLS P2MP LSPs (Originating)
==============================================================================
LSP Name Adm Opr
------------------------------------------------------------------------------
ipmsi-1001-73728 Up Up
ipmsi-4000-73729 Up Up
ipmsi-65535-73730 Up Up
------------------------------------------------------------------------------
LSPs : 3
==============================================================================
*A:Dut-C# show router mpls p2mp-lsp detail
==============================================================================
MPLS P2MP LSPs (Originating) (Detail)
==============================================================================
------------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------------
LSP Name : ipmsi-1001-73728
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61440
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 6d 21:08:37 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Disabled VprnAutoBind : Disabled
IGP Shortcut: Disabled BGP Shortcut : Disabled
BGPTransTun : Disabled
Oper Metric : Disabled
Prop Adm Grp: Disabled CSPFFirstLoose : Disabled
P2MPInstance: 1001 P2MP-Inst-type : Primary
S2L Cfg Cou*: 4 S2L Oper Count*: 4
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.2
S2l-Name : path_ipmsi To : 10.20.1.4
S2l-Name : path_ipmsi To : 10.20.1.5
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : ipmsi-4000-73729
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61441
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 6d 21:08:38 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Disabled VprnAutoBind : Disabled
IGP Shortcut: Disabled BGP Shortcut : Disabled
BGPTransTun : Disabled
Oper Metric : Disabled
Prop Adm Grp: Disabled CSPFFirstLoose : Disabled
P2MPInstance: 4000 P2MP-Inst-type : Primary
S2L Cfg Cou*: 2 S2L Oper Count*: 2
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.4
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : ipmsi-65535-73730
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61442
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 6d 21:08:39 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Disabled VprnAutoBind : Disabled
IGP Shortcut: Disabled BGP Shortcut : Disabled
BGPTransTun : Disabled
Oper Metric : Disabled
Prop Adm Grp: Disabled CSPFFirstLoose : Disabled
P2MPInstance: 65535 P2MP-Inst-type : Primary
S2L Cfg Cou*: 2 S2L Oper Count*: 2
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.4
========================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C#
*A:sim1>config>router>mpls>lsp$ show router mpls p2mp-lsp p2mp-instance s2l detail
========================================================================
MPLS LSP S2L (Detail)
========================================================================
Legend :
@ - Detour Available # - Detour In Use
b - Bandwidth Protected n - Node Protected
S - Strict L - Loose
s - Soft Preemption
========================================================================
------------------------------------------------------------------------
LSP 1 S2L 1
------------------------------------------------------------------------
LSP Name : 1 S2l LSP ID : 26624
P2MP ID : 0 S2l Grp Id : 0
Adm State : Up Oper State : Down
S2l State: : Inactive :
S2L Name : 1 To : 10.20.1.3
S2l Admin : Up S2l Oper : Down
OutInterface: n/a Out Label : n/a
S2L Up Time : 0d 00:00:00 S2L Dn Time : 0d 00:00:01
RetryAttempt: 0 NextRetryIn : 9 sec (Fast)
S2L Trans : 8 CSPF Queries: 4
Failure Code: noError Failure Node: n/a
ExplicitHops:
10.20.1.2(S)
Actual Hops :
No Hops Specified
ComputedHops:
No Hops Specified
LastResignal: n/a
========================================================================
show router mpls p2mp-lsp p2mp-instance s2l detail
========================================================================
------------------------------------------------------------------------
LSP 2 S2L 2
------------------------------------------------------------------------
LSP Name : 2 S2l LSP ID : 52230
P2MP ID : 0 S2l Grp Id : 2
Adm State : Up Oper State : Up
S2l State: : Active :
S2L Name : 2 To : 10.20.1.3
S2l Admin : Up S2l Oper : Up
OutInterface: 1/1/1 Out Label : 131071
S2L Up Time : 0d 00:04:43 S2L Dn Time : 0d 00:00:00
RetryAttempt: 0 NextRetryIn : 0 sec
S2L Trans : 5 CSPF Queries: 21
Failure Code: tunnelLocallyRepaired Failure Node: 10.20.1.2
ExplicitHops:
10.20.1.2(S)
Actual Hops :
10.10.1.1(10.20.1.1) Record Label : N/A
-> 10.10.1.2(10.20.1.2) @ # Record Label : 131071
-> 10.10.6.3(10.20.1.3) Record Label : 131068
ComputedHops:
10.10.1.1(S) -> 10.10.1.2(S) -> 10.10.5.3(S)
LastResignal: n/a
In Prog MBB :
MBB Type : GlobalRevert NextRetryIn : n/a
Timeout In : 23 sec
Started At : 06/29/2011 11:06:09 RetryAttempt: 7
FailureCode: noError Failure Node: n/a
========================================================================
*A:Dut-C>config>router>mpls>lsp$ /show router mpls lsp path detail
========================================================================
MPLS LSP Path (Detail)
========================================================================
Legend :
@ - Detour Available # - Detour In Use
b - Bandwidth Protected n - Node Protected
s - Soft Preemption
S - Strict L - Loose
========================================================================
------------------------------------------------------------------------
LSP 1 Path 1
------------------------------------------------------------------------
LSP Name : 1 Path LSP ID : 56320
From : 10.20.1.3 To : 10.10.1.1
Adm State : Up Oper State : Up
Path Name : 1 Path Type : Primary
Path Admin : Up Path Oper : Up
OutInterface: 1/1/1 Out Label : 131071
Path Up Time: 0d 00:03:09 Path Dn Time: 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
RetryAttempt: 0 NextRetryIn : 0 sec
SetupPriori*: 7 Hold Priori*: 0
Preference : n/a
Bandwidth : No Reservation Oper Bw : 0 Mbps
Hop Limit : 255 Class Type : 0
Backup CT : None
MainCT Retry: n/a MainCT Retry: 0
Rem : Limit :
Oper CT : 0
Record Route: Record Record Label: Record
Oper MTU : 1496 Neg MTU : 1496
Adaptive : Enabled Oper Metric : 1000
Include Grps: Exclude Grps:
None None
Path Trans : 1 CSPF Queries: 3
Failure Code: badNode Failure Node: 10.20.1.3
Oper Values :
Setup Prior*: 7 Hold Priori*: 0
Record Route: Record Record Label: Record
Hop Limit : 255
Adspec : Disabled
CSPF : Enabled CSPFToFirst*: Disabled
Least Fill : Disabled FR Node Pro*: Disabled
Prop Adm Grp: Disabled
Include Grps: Exclude Grps:
None None
ExplicitHops:
No Hops Specified
Actual Hops :
10.10.2.3(10.20.1.3) @ # Record Label : N/A
-> 10.10.1.1(10.20.1.1) Record Label : 131071
ComputedHops:
10.10.2.3(S) -> 10.10.2.1(S)
ResigEligib*: False
LastResignal: n/a CSPF Metric : 1000
In Prog MBB :
MBB Type : GlobalRevert NextRetryIn : 0 sec
Timeout In : 22 sec
Started At : 08/26/2011 23:59:29 RetryAttempt: 2
FailureCode: noError Failure Node: n/a
Signaled BW: 0 Mbps
========================================================================
* indicates that the corresponding row element may have been truncated.
show router mpls p2mp-lsp p2mp-instance s2l detail
------------------------------------------------------------------------
LSP 2 S2L 2
------------------------------------------------------------------------
LSP Name : 2 S2l LSP ID : 52230
P2MP ID : 0 S2l Grp Id : 4
Adm State : Up Oper State : Down
S2l State: : Inactive :
S2L Name : 2 To : 10.20.1.3
S2l Admin : Up S2l Oper : In Progress
OutInterface: n/a Out Label : n/a
S2L Up Time : 0d 00:00:00 S2L Dn Time : 0d 00:00:20
RetryAttempt: 1 NextRetryIn : n/a
Timeout In : 21 sec
S2L Trans : 6 CSPF Queries: 27
Failure Code: noError Failure Node: n/a
ExplicitHops:
10.20.1.2(S)
Actual Hops :
No Hops Specified
LastResignal: n/a
*A:Dut-C# show router mpls p2mp-lsp
=============================================================================
MPLS P2MP LSPs (Originating)
=============================================================================
LSP Name Adm Opr
------------------------------------------------------------------------
ipmsi-1001-73728 Up Up
ipmsi-4000-73729 Up Up
ipmsi-65535-73730 Up Up
------------------------------------------------------------------------
LSPs : 3
========================================================================
*A:Dut-C# show router mpls p2mp-lsp detail
========================================================================
MPLS P2MP LSPs (Originating) (Detail)
========================================================================
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : ipmsi-1001-73728
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61440
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 6d 21:08:37 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Disabled VprnAutoBind : Disabled
IGP Shortcut: Disabled BGP Shortcut : Disabled
BGPTransTun : Disabled
Oper Metric : Disabled
Prop Adm Grp: Disabled CSPFFirstLoose : Disabled
P2MPInstance: 1001 P2MP-Inst-type : Primary
S2L Cfg Cou*: 4 S2L Oper Count*: 4
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.2
S2l-Name : path_ipmsi To : 10.20.1.4
S2l-Name : path_ipmsi To : 10.20.1.5
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : ipmsi-4000-73729
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61441
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 6d 21:08:38 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Disabled VprnAutoBind : Disabled
IGP Shortcut: Disabled BGP Shortcut : Disabled
BGPTransTun : Disabled
Oper Metric : Disabled
Prop Adm Grp: Disabled CSPFFirstLoose : Disabled
P2MPInstance: 4000 P2MP-Inst-type : Primary
S2L Cfg Cou*: 2 S2L Oper Count*: 2
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.4
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : ipmsi-65535-73730
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61442
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 6d 21:08:39 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Disabled VprnAutoBind : Disabled
IGP Shortcut: Disabled BGP Shortcut : Disabled
BGPTransTun : Disabled
Oper Metric : Disabled
Prop Adm Grp: Disabled CSPFFirstLoose : Disabled
P2MPInstance: 65535 P2MP-Inst-type : Primary
S2L Cfg Cou*: 2 S2L Oper Count*: 2
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.4
========================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C#
*A:sim1>config>router>mpls>lsp$ show router mpls p2mp-lsp p2mp-instance s2l detail
========================================================================
MPLS LSP S2L (Detail)
========================================================================
Legend :
@ - Detour Available # - Detour In Use
b - Bandwidth Protected n - Node Protected
S - Strict L - Loose
s - Soft Preemption
========================================================================
------------------------------------------------------------------------
LSP 1 S2L 1
------------------------------------------------------------------------
LSP Name : 1 S2l LSP ID : 26624
P2MP ID : 0 S2l Grp Id : 0
Adm State : Up Oper State : Down
S2l State: : Inactive :
S2L Name : 1 To : 10.20.1.3
S2l Admin : Up S2l Oper : Down
OutInterface: n/a Out Label : n/a
S2L Up Time : 0d 00:00:00 S2L Dn Time : 0d 00:00:01
RetryAttempt: 0 NextRetryIn : 9 sec (Fast)
S2L Trans : 8 CSPF Queries: 4
Failure Code: noError Failure Node: n/a
ExplicitHops:
10.20.1.2(S)
Actual Hops :
No Hops Specified
ComputedHops:
No Hops Specified
LastResignal: n/a
========================================================================
A:ALU-25# show router mpls p2mp-lsp lsp_1
========================================================================
MPLS LSPs (Originating)
========================================================================
LSP Name To/P2MP ID Fastfail Adm Opr
Config
------------------------------------------------------------------------
lsp_1 18 Yes Up Up
------------------------------------------------------------------------
LSPs : 1
========================================================================
A:ALU-25#
A:ALU-25# show router mpls p2mp-lsp Test_p2mp detail
========================================================================
MPLS P2MP LSPs (Originating) (Detail)
========================================================================
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : lsp_1 LSP Tunnel ID : 1
From : 10.10.1.1 P2MP ID : 18
Adm State : Up Oper State : Down
LSP Up Time : 0d 00:00:00 LSP Down Time : 0d 20:39:48
Transitions : 0 Path Changes : 0
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : FF
Hop Limit : 255 Adaptive : Enabled
FastReroute : Disabled Oper FR : Disabled
FR Method : Facility FR Hop Limit : 45
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Disabled ADSPEC : Disabled
Metric : 1 Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
P2MPinstance:Test_p2mp p2mp-inst-type : primary
S2L Name :Test-s2l1 To : 10.20.1.6
S2L Name :Test-s2l2 To : 10.20.1.5
S2L Name :Test-s2l3 To : 10.20.1.4
------------------------------------------------------------------------
A:ALU-25#
A:ALU-25# show router mpls p2mp-lsp Test_p2mp
========================================================================
MPLS P2MP Instance (Originating)
========================================================================
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : lsp_1 LSP Tunnel ID : 1
P2MP ID : 18 Path LSP ID : 18
Adm State : Up Oper State : Down
P2MPinstance:Test_p2mp p2mp-inst-type : primary
Inst Name : lsp_1 P2MP Inst ID : 1
Adm State : Up Oper State : Down
Inst Up Time: 0d 00:00:00 Inst Down Time : 0d 20:39:48
Hop Limit : 255 Adaptive : Enabled
Record Route: Record Record Label : Record
Include Grps: Exclude Grps :
None None
Bandwidth : 0 Mbps Oper Bw : 0 Mbps
S2L Name :Test-s2l1 To : 10.20.1.6
S2L Name :Test-s2l2 To : 10.20.1.5
S2L Name :Test-s2l3 To : 10.20.1.4
------------------------------------------------------------------------
A:ALU-25#
Note that the normal output is in detailed format only. There is no separate detail format.
A:ALU-52# show router mpls p2mp-lsp [p2mp-lsp-name] p2mp-instance [p2mp-inst-name]
========================================================================
MPLS P2MP Instance (Originating)
========================================================================
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : lsp_1 LSP Tunnel ID : 1
P2MP ID : 18 Path LSP ID : 18
Adm State : Up Oper State : Down
P2MPinstance:Test_p2mp p2mp-inst-type : primary
Inst Name : lsp_1 P2MP Inst ID : 1
Adm State : Up Oper State : Down
Inst Up Time: 0d 00:00:00 Inst Down Time : 0d 20:39:48
Hop Limit : 255 Adaptive : Enabled
Record Route: Record Record Label : Record
Include Grps: Exclude Grps :
None None
Bandwidth : 0 Mbps Oper Bw : 0 Mbps
S2L Name :Test-s2l1 To : 10.20.1.6
S2L Name :Test-s2l2 To : 10.20.1.5
S2L Name :Test-s2l3 To : 10.20.1.4
------------------------------------------------------------------------
A:ALU-52#
A:ALU-52# show router mpls p2mp-lsp [p2mp-lsp-name] p2mp-instance [p2mp-inst-
name] mbb
========================================================================
MPLS P2MP Instance (Originating)
========================================================================
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : lsp_1 LSP Tunnel ID : 1
P2MP ID : 18 Path LSP ID : 18
Adm State : Up Oper State : Down
P2MPinstance:Test_p2mp p2mp-inst-type : primary
Inst Name : lsp_1 P2MP Inst ID : 1
Adm State : Up Oper State : Down
Inst Up Time: 0d 00:00:00 Inst Down Time : 0d 20:39:48
Hop Limit : 255 Adaptive : Enabled
Record Route: Record Record Label : Record
Include Grps: Exclude Grps :
None None
Bandwidth : 0 Mbps Oper Bw : 0 Mbps
Last MBB :
MBB type : Mbb State :
ended at : Old Metric :
In Prog MBB :
MBB type : Next Retry In :
Started at : Retry Attempt :
Failure code: Failure Node :
S2L Name :Test-s2l1 To : 10.20.1.6
S2l Admin : S2l Oper :
Failure code: Failure Node : 10.12.1.1
S2L Name :Test-s2l1 To : 10.20.1.6
S2l Admin : S2l Oper :
Failure code: Failure Node : 10.12.1.1
------------------------------------------------------------------------
A:ALU-52#
A:ALU-52# show router mpls p2mp-lsp [p2mp-lsp-name] p2mp-instance [p2mp-inst-
name] s2l
[s2l-name]
========================================================================
MPLS S2Ls (Originating)
========================================================================
S2L Name To Next Hop Adm Opr
------------------------------------------------------------------------
Test-s2l1 10.20.1.6 10.10.1.2 Up Up
------------------------------------------------------------------------
LSPs : 1
========================================================================
A:ALU-52#
A:ALU-52# show router mpls p2mp-lsp [p2mp-lsp-name] p2mp-instance [p2mp-inst-
name] s2l
[s2l-name] detail
========================================================================
MPLS S2Ls (Originating) (Detail)
========================================================================
------------------------------------------------------------------------
Type : Originating
------------------------------------------------------------------------
LSP Name : lsp_1 LSP Tunnel ID : 1
P2MP ID : 18 Path LSP ID : 18
Adm State : Up Oper State : Down
P2MP Primary Instance:
Inst Name : lsp_1 P2MP Inst ID : 1
Adm State : Up Oper State : Down
S2L Name : Test-s2l1 To : 10.20.1.6
Adm State : Up Oper State : Down
OutInterface: 1/1/1 Out Label : 131071
S2L Up Time : 0d 00:00:00 S2L Down Time : 0d 20:39:48
Transitions : 0 Path Changes : 0
Retry Limit : 0 Retry Timer : 30 sec
RetryAttempt: 0 NextRetryIn : 0 sec
Bandwidth : No Reservation Oper Bw : 0 Mbps
Hop Limit : 255 Adaptive : Enabled
Record Route: Record Record Label : Record
Oper MTU : 1496 Neg MTU : 1496
FastReroute : Disabled Oper FR : Disabled
FR Method : Facility FR Hop Limit : 45
FR Bandwidth: 0 Mbps FR Node Protect: Disabled
FR Object : Enabled
CSPF : Disabled ADSPEC : Disabled
Metric : 1 Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
CSPF Queries: 9
Failure Code: noError Failure Node : n/a
ExplicitHops:
No Hops Specified
Actual Hops :
10.10.1.1(10.20.1.1) @ Record Label : N/A
-> 10.10.1.2(10.20.1.2) Record Label : 131071
ComputedHops:
10.10.1.1 -> 10.10.1.2
LastResignal: n/a CSPF Metric : 1000
------------------------------------------------------------------------
A:ALU-52#
*A:Dut-C# show router mpls p2mp-lsp "ipmsi-1-73752" detail
=======================================================================
MPLS P2MP LSPs (Originating) (Detail)
=======================================================================
-------------------------------------------------------------------------------
Type : Originating
-----------------------------------------------------------------------
LSP Name : ipmsi-1-73752
LSP Type : P2mpAutoLsp LSP Tunnel ID : 61445
From : 10.20.1.3
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:00:51 LSP Down Time : 0d 00:00:00
Transitions : 3 Path Changes : 3
Retry Limit : 0 Retry Timer : 30 sec
Signaling : RSVP Resv. Style : SE
Hop Limit : 255 Negotiated MTU : n/a
Adaptive : Enabled ClassType : 0
FastReroute : Enabled Oper FR : Enabled
FR Method : Facility FR Hop Limit : 16
FR Node Pro*: Disabled FR Prop Adm Grp: Disabled
FR Object : Enabled
Egress Stats: Enabled Egress Oper St*: Out-of-resource
CSPF : Enabled ADSPEC : Disabled
Metric : Disabled Use TE metric : Disabled
Include Grps: Exclude Grps :
None None
Least Fill : Disabled
Auto BW : Disabled
LdpOverRsvp : Enabled VprnAutoBind : Enabled
IGP Shortcut: Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : Disabled
Prop Adm Grp: Disabled
P2MPInstance: 1 P2MP-Inst-type : Primary
S2L Cfg Cou*: 4 S2L Oper Count*: 4
S2l-Name : path_ipmsi To : 10.20.1.1
S2l-Name : path_ipmsi To : 10.20.1.2
S2l-Name : path_ipmsi To : 10.20.1.5
S2l-Name : path_ipmsi To : 10.20.1.6
=======================================================================
p2mp-policy
p2mp-policy
Syntax
p2mp-policy [root-address ip-address] [tree-id tree-id] [candidate-path path-name] [ detail]
Context
[Tree] (show>router>p2mp-sr-tree>database p2mp-policy)
Full Context
show router p2mp-sr-tree database p2mp-policy
Description
This command displays the policy information present in the P2MP SR tree database.
Parameters
- ip-address
-
Specifies the root IPv4 address.
- tree-id
-
Specifies the P2MP SR tree ID.
- path-name
-
Specifies the candidate path name, up to 64 characters.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of P2MP SR tree database policy information.
Output ExampleA:node-2>show>router>p2mp-sr-tree>database# p2mp-policy
===============================================================================
P2MP Policies
===============================================================================
Policy-Name
RootAddr TreeId State NumPaths
Tunnel Active-Path
Candidate-Path Origin ASN PLSP-ID
State Create-Time Desc
-------------------------------------------------------------------------------
test
100.0.0.103 9000 inService 1
73729 Primary-path
Primary-path configuration 0 --
inService 0d 00:00:01 1
test-spmsi
100.0.0.103 9001 inService 1
0 Primary-path
Primary-path configuration 0 --
inService 0d 00:00:01 1
-------------------------------------------------------------------------------
Total P2MP Policies : 2
p2mp-policy
Syntax
p2mp-policy [policy-name] [root-tree-id root-tree-id] [root-addr ip-address]
Context
[Tree] (show>router>p2mp-sr-tree p2mp-policy)
Full Context
show router p2mp-sr-tree p2mp-policy
Description
This command displays the P2MP policy information.
Parameters
- policy-name
-
Specifies the policy name, up to 256 characters.
- root-tree-id
-
Specifies the root tree ID.
- ip-address
-
Specifies the root IPv4 address.
Platforms
All
Output
The following output is an example of P2MP SR tree policy information.
Output ExampleA:swsim103>show>router>p2mp-sr-tree# p2mp-policy
===============================================================================
P2MP Policies
===============================================================================
Name TreeId NumPaths Adm/Opr
RootAddr SvcId
activeCPName ActInstId
-------------------------------------------------------------------------------
test 9000 1 Up/Up
100.0.0.103 70
Primary-path 1
test-spmsi 9001 1 Up/Up
100.0.0.103 70
Primary-path 1
-------------------------------------------------------------------------------
Total P2MP Policies : 2
===============================================================================
p2mp-sr-tree
p2mp-sr-tree
Syntax
p2mp-sr-tree
Context
[Tree] (show>router p2mp-sr-tree)
Full Context
show router p2mp-sr-tree
Description
Commands in this context display P2MP SR tree information.
Platforms
All
packet
packet
Syntax
packet packet-number
Context
[Tree] (show>test-oam>build-packet packet)
Full Context
show test-oam build-packet packet
Description
This command displays the OAM egress port finder information for a specific packet.
Parameters
- packet-number
-
Specifies the packet number.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
packet-size
packet-size
Syntax
packet-size protocol [clear]
Context
[Tree] (tools>dump>cflowd packet-size)
Full Context
tools dump cflowd packet-size
Description
This command displays packet size distribution for sampled IP traffic. Values are displays in decimal format (1.0 = 100%, .500 = 50%). Separate statistics are maintained and shown for IPv4 and IPv6 traffic.
Platforms
All
Output
The following output is an example of cflowd packet size information.
Output ExampleSR-12# tools dump cflowd packet-size ipv4
IP packet size distribution (801600 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.000 .250 .000 .000 .010 .100 .500 .090 .000 .000 .000 .000 .000 .000 .000
512 544 576 1024 1536 2048 2560 3072 3584 4096 4608 9000
.000 .000 .000 .050 .000 .000 .000 .000 .000 .000 .000 .000
parameters
parameters
Syntax
parameters
Context
[Tree] (show>router>ldp parameters)
Full Context
show router ldp parameters
Description
This command displays configuration information about LDP parameters.
Platforms
All
Output
LDP Parameters Output
LDP Parameters Output Fields describes the LDP parameters output fields.
|
Label |
Description |
|---|---|
|
Keepalive Timeout |
The time interval (in s), that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). |
|
Timeout Factor |
The value by which the keepalive timeout should be divided to give the keepalive time, for example, the time interval (in s), between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. |
|
Hold Time |
The hello time, also known as hold time. It is the time interval (in s), that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. |
|
Hello Factor |
The value by which the hello timeout should be divided to give the hello time, for example, the time interval (in s), between LDP hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. |
|
Auth |
Enabled — Authentication using MD5 message based digest protocol is enabled. Disabled — No authentication is used. |
|
Admin Status |
inService — The LDP is administratively enabled. outService — The LDP is administratively disabled. |
|
Deaggregated FECs |
False — LDP aggregates multiple prefixes into a single Forwarding Equivalence Class (FEC) and advertises a single label for the FEC. This value is only applicable to LDP interfaces and not for targeted sessions. True — LDP de-aggregates prefixes into multiple FECs. |
|
Propagate Policy |
The Propagate Policy value specifies whether the LSR should generate FECs and which FECs it should generate. system — LDP distributes label bindings only for the router's system IP address. interface — LDP distributes label bindings for all LDP interfaces. all — LDP distributes label bindings for all prefixes in the routing table. none — LDP does not distribute any label bindings. |
|
Transport Address |
interface — The interface's IP address is used to set up the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used because only one LDP session is actually set up between the two neighbors. system — The system's IP address is used to set up the LDP session between neighbors. |
|
Label-Retention |
liberal — All advertised label mappings are retained whether they are from a valid next hop or not. When the label distribution value is downstream unsolicited, a router may receive label bindings for the same destination for all its neighbors. Labels for the non-next hops for the FECs are retained in the software but not used. When a network topology change occurs where a non-nexthop becomes a true next hop, the label received earlier is then used. conservative — Advertised label mappings are retained only if they are used to forward packets; for example, if the label came from a valid next hop. Label bindings received from non-next hops for each FEC are discarded. |
|
Control Mode |
ordered — Label bindings are not distributed in response to a label request until a label binding has been received from the next hop for the destination. independent — Label bindings are distributed immediately in response to a label request even if a label binding has not yet been received from the next hop for the destination. |
|
Route Preference |
The route preference assigned to LDP routes. When multiple routes are available to a destination, the route with the lowest preference is used. This value is only applicable to LDP interfaces and not for targeted sessions. |
|
Loop Detection |
none — Loop detection is not supported on this router. This is the only valid value because Path Vector based loop detection is not supported. other — Loop detection is supported but by a method other than hopCount, pathVector, or hopCountAndPathVector. hopCount — Loop detection is supported by hop count only. pathVector — Loop detection is supported by path vector only. hopCountAndPathVector — Loop detection is supported by both path vector and hop count. |
|
Keepalive Timeout |
The factor used to derive the Keepalive interval. |
|
Keepalive Factor |
The time interval (in s), that LDP waits before tearing down the session. |
|
Hold-Time |
The time left before a neighbor is declared to be down. |
|
Hello Factor |
The value by which the hello timeout should be divided to give the hello time, for example, the time interval (in s), between LDP hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. |
|
Auth |
Enabled — Authentication using MD5 message based digest protocol is enabled. Disabled — No authentication is used. |
|
Passive-Mode |
true — LDP responds only when it gets a connect request from a peer and does not attempt to actively connect to its neighbors. false — LDP actively tries to connect to its peers. |
|
Targeted-Sessions |
true — Targeted sessions are enabled. false — Targeted sessions are disabled. |
*A:Dut-A# show router ldp parameters
===============================================================================
LDP Parameters (IPv4 LSR ID 10.20.1.1:0)
(IPv6 LSR ID 3ffe::a14:101[0])
===============================================================================
-------------------------------------------------------------------------------
Graceful Restart Parameters
-------------------------------------------------------------------------------
Graceful Restart : Disabled
Nbor Liveness Time : 120 sec Max Recovery Time : 120
-------------------------------------------------------------------------------
IPv4 Interface Parameters
-------------------------------------------------------------------------------
Keepalive Timeout : 30 sec Keepalive Factor : 3
Hold Time : 15 sec Hello Factor : 3
Transport Address : system
-------------------------------------------------------------------------------
IPv6 Interface Parameters
-------------------------------------------------------------------------------
Keepalive Timeout : 30 sec Keepalive Factor : 3
Hold Time : 15 sec Hello Factor : 3
Transport Address : system
-------------------------------------------------------------------------------
Targeted Session Parameters
-------------------------------------------------------------------------------
Import Pfx Policies: None Export Pfx Policies : None
Prefer Tunl-in-Tunl: Disabled SDP Auto Targ Sess : Enabled
-------------------------------------------------------------------------------
IPv4 Targeted Session Parameters
-------------------------------------------------------------------------------
Keepalive Timeout : 30 sec Keepalive Factor : 3
Hold Time : 15 sec Hello Factor : 3
Hello Reduction : Disabled Hello Reduction Fctr: 3
-------------------------------------------------------------------------------
IPv6 Targeted Session Parameters
-------------------------------------------------------------------------------
Keepalive Timeout : 40 sec Keepalive Factor : 4
Hold Time : 45 sec Hello Factor : 3
Hello Reduction : Disabled Hello Reduction Fctr: 3
===============================================================================
*A:Dut-A#
partition
partition
Syntax
partition summary
Context
[Tree] (show>app-assure>group partition)
Full Context
show application-assurance group partition
Description
This command displays partition information.
Parameters
- summary
-
Displays partition summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
passive-dns
passive-dns
Syntax
passive-dns
Context
[Tree] (tools>dump>app-assure>group>ipassist passive-dns)
Full Context
tools dump application-assurance group ip-identification-assist passive-dns
Description
Commands in this context display passive DNS monitoring statistics related to IP identification assist for top applications using IP addresses learned by passive monitoring of DNS traffic.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
password-options
password-options
Syntax
password-options
Context
[Tree] (show>system>security password-options)
Full Context
show system security password-options
Description
This command displays configured password options.
Platforms
All
Output
The following output is an example of password options information, and Show Password Options Output Fields describes the output fields.
Output ExampleA:ALA-7# show system security password-options
===============================================================================
Password Options
===============================================================================
Password aging in days : none
Time required between password changes : 0d 00:10:00
Number of invalid attempts permitted per login : 3
Time in minutes per login attempt : 5
Lockout period (when threshold breached) : 10
Authentication order : radius tacplus local
User password history length : disabled
Password hashing : bcrypt
Accepted password length : 6..56 characters
Credits for each character type : none
Required character types : none
Minimum number different character types : 0
Required distance with previous password : 5
Allow consecutively repeating a character : always
Allow passwords containing username : yes
Palindrome allowed : no
===============================================================================
A:ALA-7#
|
Label |
Description |
|---|---|
|
Password aging in days |
Displays the number of days a user password is valid before the user must change their password. |
|
Time required between password changes |
Displays the time interval between changed passwords. |
|
Number of invalid attempts permitted per login |
Displays the number of unsuccessful login attempts allowed for the specified time. |
|
Time in minutes per login attempt |
Displays the period of time, in minutes, that a specified number of unsuccessful attempts can be made before the user is locked out. |
|
Lockout period (when threshold breached) |
Displays the number of minutes that the user is locked out if the threshold of unsuccessful login attempts has been exceeded. |
|
Authentication order |
Displays the sequence in which password authentication is attempted among RADIUS, TACACS+, and local passwords. |
|
User password history length |
Displays the size of the password history file to be stored. |
|
Password hashing |
Displays the system hashing algorithm for passwords. |
|
Accepted password length |
Displays the minimum length required for local passwords. |
|
Credits for each character type |
Displays the credit for each character type. A credit is obtained for a specific character type; for example, uppercase, lowercase, numeric, or special character. Credits per character type are configurable. Credits can be used toward the minimum length of the password, so a trade-off can be made between a very long, simple password and a short, complex one. |
|
Required character types |
Displays the character types that are required in a password; for example, uppercase, lowercase, numeric, or special character. |
|
Minimum number different character types |
Displays the minimum number of each different character types in a password. |
|
Required distance with previous password |
Displays the minimum Levenshtein distance between a new password and the old password. |
|
Allow consecutively repeating a character |
Displays the number of times the same character is allowed to be repeated consecutively. |
|
Allow passwords containing username |
Displays whether the user name is allowed as part of the password. |
|
Palindrome allowed |
Displays whether palindromes are allowed as part of the password. |
password-options
Syntax
password-options
Context
[Tree] (show>system>security password-options)
Full Context
show system security password-options
Description
This command displays password options.
Platforms
All
Output
The following output is an example of password option information.
Show Password-Options Output Fields describes password-options output fields.
Output ExampleA:ALA-48>show>system>security# password-options
===============================================================================
Password Options
===============================================================================
Password aging in days : 365
Number of invalid attempts permitted per login : 5
Time in minutes per login attempt : 5
Lockout period (when threshold breached) : 20
Authentication order : radius tacplus local
User password hashing algorithm : bcrypt
Configured complexity options :
Minimum password length : 8
===============================================================================
A:ALA-48>show>system>security#
|
Label |
Description |
|---|---|
|
Password aging in days |
Displays the number of days a user password is valid before the user must change his password. |
|
Number of invalid attempts permitted per login |
Displays the maximum number of unsuccessful login attempts allowed for a user. |
|
Time in minutes per login attempt |
Displays the time in minutes that user is to be locked out. |
|
Lockout period (when threshold breached) |
Displays the number of minutes the user is locked out if the threshold of unsuccessful login attempts has exceeded. |
|
Authentication order |
Displays the most preferred method to authenticate and authorize a user. |
|
User password hashing algorithm |
Displays the algorithm with which the system hashes the user passwords. |
|
Configured complexity options |
Displays the complexity requirements of locally administered passwords, HMAC-MD5-96, HMAC-SHA-96 and DES-keys configured in the authentication section. |
|
Minimum password length |
Displays the minimum number of characters required in the password. |
path
path
Syntax
path [path-name] [lsp-binding]
path path-name p2mp-lsp-binding
Context
[Tree] (show>router>mpls path)
Full Context
show router mpls path
Description
This command displays MPLS paths.
Parameters
- path-name
-
Specifies the unique name label for the LSP path.
- lsp-binding
-
Displays binding information.
- p2mp-lsp-binding
-
Displays binding information.
Platforms
All
Output
The following output is an example of MPLS path information.
MPLS Path Output Fields describes MPLS Path output fields.
|
Label |
Description |
|---|---|
|
Path Name |
The unique name label for the LSP path. |
|
Adm |
Down — The path is administratively disabled. Up — The path is administratively enabled. |
|
Hop Index |
The value used to order the hops in a path. |
|
IP Address |
The IP address of the hop that the LSP should traverse on the way to the egress router. |
|
Strict/Loose |
Strict — The LSP must take a direct path from the previous hop router to the next router. Loose — The route taken by the LSP from the previous hop to the next hop can traverse through other routers. |
|
LSP Name |
The name of the LSP used in the path. |
|
Binding |
Primary — The preferred path for the LSP. Secondary — The standby path for the LSP. |
|
Paths |
Total number of paths configured. |
*A:SRU4>config>router>mpls# show router mpls path
===============================================================================
MPLS Path:
===============================================================================
Path Name Adm Hop Index IP Address Strict/Loose
-------------------------------------------------------------------------------
to_10_30_1_1 Up no hops n/a n/a
to_10_30_1_2 Up no hops n/a n/a
to_10_30_1_3 Up no hops n/a n/a
to_10_30_1_4 Up no hops n/a n/a
to_10_30_1_5 Up no hops n/a n/a
to_10_30_1_6 Up no hops n/a n/a
to_10_30_1_110 Up no hops n/a n/a
to_10_8_100_15 Up no hops n/a n/a
to_10_20_1_20 Up no hops n/a n/a
to_10_20_1_22 Up no hops n/a n/a
to_10_100_1_1 Up no hops n/a n/a
------------------------------------------------------------------------------
Paths : 11
===============================================================================
*A:SRU4>config>router>mpls#
*A:SRU4>config>router>mpls# show router mpls path lsp-binding
===============================================================================
MPLS Path:
===============================================================================
Path Name Opr LSP Name Binding
-------------------------------------------------------------------------------
to_10_30_1_1 Up to_10_30_1_1_cspf Primary
Up to_10_30_1_1_cspf_2 Primary
Up to_10_30_1_1_cspf_3 Primary
Up to_10_30_1_1_cspf_16 Primary
Up to_10_30_1_1_cspf_17 Primary
Up to_10_30_1_1_cspf_18 Primary
Up to_10_30_1_1_cspf_19 Primary
Up to_10_30_1_1_cspf_20 Primary
to_10_30_1_2 Up to_10_30_1_2_cspf Primary
Up to_10_30_1_2_cspf_2 Primary
Up to_10_30_1_2_cspf_3 Primary
Up to_10_30_1_2_cspf_4 Primary
Up to_10_30_1_2_cspf_5 Primary
...
to_10_100_1_1 Down to_10_100_1_1_cspf Primary
Down to_10_100_1_1_cspf_2 Primary
Down to_10_100_1_1_cspf_3 Primary
Down to_10_100_1_1_cspf_4 Primary
Down to_10_100_1_1_cspf_5 Primary
Down to_10_100_1_1_cspf_6 Primary
Down to_10_100_1_1_cspf_13 Primary
Down to_10_100_1_1_cspf_14 Primary
Down to_10_100_1_1_cspf_15 Primary
Down to_10_100_1_1_cspf_16 Primary
Down to_10_100_1_1_cspf_17 Primary
Down to_10_100_1_1_cspf_18 Primary
Down to_10_100_1_1_cspf_19 Primary
Down to_10_100_1_1_cspf_20 Primary
-------------------------------------------------------------------------------
Paths : 11
===============================================================================
*A:SRU4>config>router>mpls#
path-request
path-request
Syntax
path-request [lsp-type lsp-type] [dest ip-address] [ detail]
Context
[Tree] (show>router>pcep>pcc path-request)
Full Context
show router pcep pcc path-request
Description
This command displays the PCEP path request information.
Parameters
- lsp-type
-
Specifies the LSP type.
- ip-address
-
Specifies the IP address.
- detail
-
Specifies detailed information.
Platforms
All
paths
paths
Syntax
paths
Context
[Tree] (show>router>bgp paths)
Full Context
show router bgp paths
Description
This command displays a summary of BGP path attributes.
Platforms
All
Output
The following output is an example of BGP path information. Show Router BGP Path Field Descriptions describes the output fields.
Output Example*A:ALA-12# show router 3 bgp paths
==============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
==============================================================================
BGP Paths
------------------------------------------------------------------------------
Path: 60203 65001 19855 3356 15412
------------------------------------------------------------------------------
Origin : IGP Next Hop : 10.0.28.1
MED : 60203 Local Preference : none
Refs : 4 ASes : 5
Segments : 1
Flags : EBGP-learned
Aggregator : 15412 62.216.140.1
------------------------------------------------------------------------------
Path: 60203 65001 19855 3356 1 1236 1236 1236 1236
------------------------------------------------------------------------------
Origin : IGP Next Hop : 10.0.28.1
MED : 60203 Local Preference : none
Refs : 2 ASes : 9
Segments : 1
Flags : EBGP-learned
------------------------------------------------------------------------------
*A:ALA-12#
|
Label |
Description |
|---|---|
|
BGP Router ID |
The local BGP router ID. |
|
AS |
The configured autonomous system number. |
|
Local AS |
The configured local AS setting. If not configured, then the value is the same as the AS. |
|
Path |
The AS path attribute. |
|
Origin |
EGP — The NLRI is learned by an EGP protocol. IGP — The NLRI is interior to the originating AS. INCOMPLETE — NLRI was learned another way. |
|
Next Hop |
The advertised BGP nexthop. |
|
MED |
The Multi-Exit Discriminator value. |
|
Local Preference |
The local preference value. |
|
Refs |
The number of routes using a specified set of path attributes. |
|
ASes |
The number of autonomous system numbers in the AS path attribute. |
|
Segments |
The number of segments in the AS path attribute. |
|
Flags |
EBGP-learned — Path attributes learned by an EBGP peering. IBGP-Learned — Path attributes learned by an IBGP peering. |
|
Aggregator |
The route aggregator ID. |
|
Community |
The BGP community attribute list. |
|
Originator ID |
The originator ID path attribute value. |
|
Cluster List |
The route reflector cluster list. |
pattern-match
pattern-match
Syntax
pattern-match [detail]
Context
[Tree] (tools>dump>filter>resources pattern-match)
Full Context
tools dump filter resources pattern-match
Description
This command displays pattern match records.
Parameters
- detail
-
Displays detailed pattern match records.
Platforms
All
Output
The following output is an example of detailed pattern match records.
Output ExampleA:Dut-A# tools dump filter resources pattern-match
===============================================================================
Unique filter pattern match patterns
===============================================================================
Used : 1
Free : 1022
Total : 1023
===============================================================================
A:Dut-A# tools dump filter resources pattern-match detail
===================================================================
Unique pattern match
===================================================================
Num Pattern Mask Not emb. Emb.
-------------------------------------------------------------------
1 0xff00000000000000 0xff00000000000000 1 0
===================================================================
===============================================================================
Unique filter pattern match patterns
===============================================================================
Used : 1
Free : 1022
Total : 1023
===============================================================================
pbb
pbb
Syntax
pbb base
pbb mac-name
pbb mac-name mac-name detail
Context
[Tree] (show>service pbb)
Full Context
show service pbb
Description
This command displays PBB information.
Parameters
- base
-
Displays information about a PBB base.
- mac-name
-
Displays MAC name information.
- detail
-
Displays detailed information.
- mac-name
-
Displays information about a specific MAC name, up to 32 characters.
Platforms
All
Output
The following output is an example of PBB base information.
Output Example*A:Dut-B# show service pbb base
======================================================================
PBB MAC Information
======================================================================
MAC-Notif Count : 3
MAC-Notif Interval : 1
Source BMAC : Default
======================================================================
The following output is an example of PBB MAC information.
Output Example*A:Dut-B# show service pbb mac-name
=====================================================================
MAC Name Table
=====================================================================
MAC-Name MAC-Address
---------------------------------------------------------------------
test 00:03:03:03:03:02
=====================================================================
*A:Dut-B# show service pbb mac-name test detail
=====================================================================
Services Using MAC name='test' addr='00:03:03:03:03:02'
=====================================================================
Svc-Id ISID
---------------------------------------------------------------------
501 501
---------------------------------------------------------------------
Number of services: 1
=====================================================================
*A:Dut-B#
pbr-steering
pbr-steering
Syntax
pbr-steering
Context
[Tree] (show>router pbr-steering)
Full Context
show router pbr-steering
Description
This command displays PBR steering VAS interfaces with VAS interface type configuration.
Platforms
All
Output
The following output is an example of router PBR steering VAS interfaces information.
Output ExampleA:Dut-C# show router pbr-steering
===============================================================================
PBR Steering VAS interfaces
===============================================================================
Interface-Name VAS IF Type
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
PBR Steering IPv4 filters
===============================================================================
Ingress filter
Interface Interface name
PBR Control
PBR Types
-------------------------------------------------------------------------------
1
pxc-20.b:1.1 N/A
Mgmt
IP
-------------------------------------------------------------------------------
Number of ingress IPv4 filters with PBR: 1
-------------------------------------------------------------------------------
Egress filter
Interface Interface name
PBR Control
PBR Types
-------------------------------------------------------------------------------
2
pxc-20.b:1.1 N/A
Mgmt
IP
-------------------------------------------------------------------------------
Number of egress IPv4 filters with PBR: 1
===============================================================================
===============================================================================
PBR Steering IPv6 filters
===============================================================================
Ingress filter
Interface Interface name
PBR Control
PBR Types
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Egress filter
Interface Interface name
PBR Control
PBR Types
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
pcap
pcap
Syntax
pcap [session-name] [detail]
Context
[Tree] (show pcap)
Full Context
show pcap
Description
This command shows the information about the packet capture session and confirms if the packet is reliable.
Parameters
- session-name
-
Specifies the session name up to 32 characters.
Platforms
All
Output
The following output is an example of information about the packet capture session.
Output Example===============================================================================
Pcap Session "1" Information
===============================================================================
Application Type : mirror-dest Session State : ready
Capture : stop Last Changed : 02/06/2018 19:52:07
Capture File Url : ftp://*:*@192.168.40.1/pcap.pcap
Buffer Size : 0 Bytes File Size : 0 Bytes
Write Failures : 0 Read Failures : 0
Proc Time Bailouts : 0 Last File Write : 02/06/2018 19:52:07
Dropped Packets : 0 Packets
===============================================================================
|
Label |
Description |
|---|---|
|
Buffer Size |
The maximum buffer size is 20 Mb. If the number of packets in the buffer exceeds 20 Mb, packets are dropped. |
|
File Size |
The current size of the capture file. |
|
Write Failures |
The number of errors that occurred when packets were written into the buffer. A number greater than zero indicates that some packets were not captured. |
|
Read Failures |
The errors occurred when packets were read from the buffer for exporting to FTP or TFTP. A number greater than zero indicates that some packets were not captured. |
|
Process Time Bailouts |
A system process timeout. Some packets were not captured. |
|
Dropped Packets |
The number of packets dropped from the buffer due to errors. |
pcc
pcc
Syntax
pcc
Context
[Tree] (clear>router>pcep pcc)
Full Context
clear router pcep pcc
Description
Commands in this context clear PCEP PCC related data.
Platforms
All
pcc
Syntax
pcc
Context
[Tree] (show>router>pcep pcc)
Full Context
show router pcep pcc
Description
Commands in this context display PCEP PCC related information.
Platforms
All
pcc
Syntax
pcc
Context
[Tree] (tools>dump>router>pcep pcc)
Full Context
tools dump router pcep pcc
Description
Commands in this context dump tools for PCEP PCC.
Platforms
All
pcc-rule
pcc-rule
Syntax
pcc-rule
pcc-rule monitoring-key key detail
pcc-rule rule-id id detail
pcc-rule rule-name rule-name
pcc-rule rule-name rule-name detail
pcc-rule summary
pcc-rule monitoring-key key
Context
[Tree] (show>subscr-mgmt pcc-rule)
Full Context
show subscriber-mgmt pcc-rule
Description
This command displays a list of PCC rules and associated monitoring keys in the system.
Parameters
- key
-
Displays details about a specific monitoring-key.
- id
-
Displays details about a specific PCC rule.
- rule-name
-
Displays information about a specific PCC rule.
- summary
-
Displays summarized information for active rules in the system.
- key
-
Displays information about a specific monitoring-key.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management PCC rule information.
Output Exampleshow subscriber-mgmt pcc-rule summary
===============================================================================
PCC Rules Summary
===============================================================================
Nbr Active PCC Rules : 26 / 1023
Nbr Active Combinations
IPv4 Filter : 2 / 4095
IPv6 Filter : 0 / 4095
Egress Qos : 1 / 4095
Ingress Qos : 1 / 4095
===============================================================================
show subscriber-mgmt pcc-rule
===============================================================================
Id Dir ForwardAction QosAction
-------------------------------------------------------------------------------
name : RULE_egress_FC
monitorKey: -
29 egr - fc
name : RULE_egress_UM
monitorKey: um_RULE_egress_UM
34 egr - monitor
name : RULE_ingress_FC
monitorKey: -
37 ingr - fc
name : RULE_ingress_UM
monitorKey: um_RULE_ingress_UM
50 ingr - monitor
name : RULE_egress_DROP
monitorKey: -
28 egr drop -
name : RULE_ingress_RDR
monitorKey: -
49 ingr fwd nh4 -
name : RULE_egress_UM_FC
monitorKey: um_RULE_egress_UM_FC
35 egr - fc monitor
…
===============================================================================
show subscriber-mgmt pcc-rule rule-name "RULE_ingress_RATE_LIMIT_UM_FC_RDR" detail
===============================================================================
PCC Rules
===============================================================================
PCC rule name : RULE_ingress_RATE_LIMIT_UM_FC_RDR
PCC rule id : 47
Monitoring key : um_RULE_ingress_RATE_LIMIT_UM_FC_RDR
Flow status : Enabled
Nbr of Flows : 1 (ingress)
HTTP-Redirect : -
Next-Hop Redir. IPv4 : 10.10.10.10
Next-Hop Redir. IPv6 : -
QoS Ingr. CIR/PIR : 1000 kbps / 2000 kbps
QoS Egr. CIR/PIR : - / -
FC change : h2
-------------------------------------------------------------------------------
Flows
-------------------------------------------------------------------------------
Src. IP : any Src. Port: -
Dst. IP : 75.24.24.17/32 Dst. Port: -
Protocol : 6 DSCP : cp60
-------------------------------------------------------------------------------
===============================================================================
show service active-subscribers pcc-rule subscriber "1/1/3:1.1|00:00:00:00:00:01"
===============================================================================
Active Subscribers
===============================================================================
-------------------------------------------------------------------------------
Subscriber 1/1/3:1.1|00:00:00:00:00:01 (subprof1)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
(1) SLA Profile Instance sap:1/1/3:1.1 - sla:sla1
-------------------------------------------------------------------------------
Ingr Qos Policy Override : 3:P2
Egr Qos Policy Override : 2:P2
-------------------------------------------------------------------------------
IP Address
MAC Address PPPoE-SID Origin
--------------------------------------------------------
22.1.0.1
00:00:00:00:00:01 N/A DHCP
--------------------------------------------------------
Ingr Filter Override : 5:P4
Egr Filter Override : 6:P5
========================================================
Preference Rule Id Rule Name
--------------------------------------------------------
0 28 RULE_egress_DROP
0 29 RULE_egress_FC
0 30 RULE_egress_RATE_LIMIT
0 31 RULE_egress_RATE_LIMIT_FC
0 32 RULE_egress_RATE_LIMIT_UM
0 33 RULE_egress_RATE_LIMIT_UM_FC
0 34 RULE_egress_UM
0 35 RULE_egress_UM_FC
0 36 RULE_ingress_DROP
0 37 RULE_ingress_FC
0 38 RULE_ingress_FC_HTTP
0 39 RULE_ingress_FC_RDR
0 40 RULE_ingress_HTTP
0 41 RULE_ingress_RATE_LIMIT
0 42 RULE_ingress_RATE_LIMIT_FC
0 43 RULE_ingress_RATE_LIMIT_FC_RDR
0 44 RULE_ingress_RATE_LIMIT_RDR
0 45 RULE_ingress_RATE_LIMIT_UM
0 46 RULE_ingress_RATE_LIMIT_UM_FC
0 47 RULE_ingress_RATE_LIMIT_UM_FC_RDR
0 48 RULE_ingress_RATE_LIMIT_UM_RDR
0 49 RULE_ingress_RDR
0 50 RULE_ingress_UM
0 51 RULE_ingress_UM_FC
0 52 RULE_ingress_UM_FC_RDR
0 53 RULE_ingress_UM_RDR
========================================================
Policy and Charging Control Rule Field Descriptions describes subscriber management PCC rule output fields.
|
Field |
Description |
|---|---|
|
Nbr Active PCC Rules |
The number of active PCC rules |
|
Nbr Active Combinations |
The number of active IP PCC rule combinations |
|
IPv4 Filter |
The number of IPv4 filter combinations |
|
IPv6 Filter |
The number of IPv6 filter combinations |
|
Egress QoS |
The number of active egress QoS PCC rule combinations |
|
Ingress QoS |
The number of active ingress QoS PCC rule combinations |
|
Id |
The PCC ID |
|
Dir |
The flow direction on which the PCC-rule acts |
|
ForwardAction |
The filter action of the PCC-rule |
|
QosAction |
The Qos action of the PCC-rule. The value account(3) is only relevant if the PCC-rule was received by the system as part of a RADIUS Subscriber Service attribute |
|
name |
The PCC rule name |
|
monitorKey |
The monitor key name that can be received in a PCC rule. An empty string (length 0) indicates that no monitor key is defined in the PCC rule |
|
PCC rule name |
The name of a PCC rule |
|
PCC rule id |
The PCC rule ID |
|
Monitoring key |
The monitoring key defined in this PCC-rule. This value is only considered if monitor is set in the QoS action. |
|
Flow status |
The PCC rule flow status; enabled or disabled |
|
Nbr of Flows |
The number of flow rules defined in this PCC rule |
|
HTTP-Redirect |
The URL to which all data flows that pertain to this PCC-rule must be redirected |
|
Next-Hop Redir. IPv4 |
The IPv4 address to which all IPv4 data flows that pertain to this PCC-rule be redirected |
|
Next-Hop Redir. IPv6 |
The IPv6 address to which all IPv6 data flows that pertain to this PCC-rule be redirected |
|
QoS Ingr. CIP/PIR |
The ingress QoS CIP and PIR values |
|
QoS Egr. CIP/PIR |
The egress QoS CIP and PIR values |
|
FC change |
The forwarding class (FC) that is assigned to all data flows that pertain to this PCC-rule |
|
Src. IP |
The address type of the source address |
|
Src. Port |
The port type of the source address |
|
Dst. IP |
The address type of the destination address |
|
Protocol |
The IPv4 protocol value, and for IPv6 the next header type used in the match criteria for this flow
|
|
DSCP |
The DSCP to be matched for this flow |
|
Subscriber |
The subscriber SAP |
|
SLA Profile Instance sap |
The SLA profile instance SAP |
|
Ingr QoS Policy Override |
The ID of the overriding ingress Qos policy |
|
Egr QoS Policy Override |
The ID of the overriding egress Qos policy |
|
IP Address |
The subscriber IP address |
|
MAC Address |
The subscriber MAC address |
|
PPPoE-SID |
The PPPoE session ID of this subscriber host |
|
Origin |
The origin of this subscriber host |
|
Preference |
The preference with respect to other PCC rules |
|
Rule ID |
The PCC rule ID |
|
Rule Name |
The PCC rule name |
pcc-rule
Syntax
pcc rule [subscriber sub-ident-string]
pcc rule [subscriber sub-ident-string] detail
Context
[Tree] (show>service>active-subscribers pcc-rule)
Full Context
show service active-subscribers pcc-rule
Description
This command specifies the PCC rule.
Parameters
- sub-ident-string
-
Specifies the sub-ident-string, up to 32 characters.
- detail
-
Displays detailed information for the specified PCC rule.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pce-associations
pce-associations
Syntax
pce-associations
Context
[Tree] (show>router>pcep>pcc pce-associations)
Full Context
show router pcep pcc pce-associations
Description
Commands in this context display information about PCE associations configured under the PCC.
Platforms
All
pcep
pcep
Syntax
pcep
Context
[Tree] (clear>router pcep)
Full Context
clear router pcep
Description
Commands in this context clear PCEP related data.
Platforms
All
pcep
Syntax
pcep
Context
[Tree] (show>router pcep)
Full Context
show router pcep
Description
Commands in this context display PCEP related information.
Platforms
All
pcep
Syntax
pcep
Context
[Tree] (tools>dump>router pcep)
Full Context
tools dump router pcep
Description
Commands in this context dump tools for PCEP.
Platforms
All
pcm
pcm
Syntax
pcm [pcm-slot] [chassis chassis-id] [ detail]
Context
[Tree] (show pcm)
Full Context
show pcm
Description
This command displays PCM information.
Parameters
- pcm-slot
-
Specifies the PCM slot identifier.
- chassis-id
-
Specifies the chassis ID for the router chassis.
- detail
-
Displays detailed information.
Platforms
7950 XRS-20e
Output
The following output is an example of PCM information.
Output Example: show pcm*A:Dut-A# show pcm
===============================================================================
PCM Summary
===============================================================================
Chassis/ Provisioned Type Operational Input Zone
Slot Equipped Type (if diff) State A B2 A2 B
-------------------------------------------------------------------------------
1/9 (not provisioned) unprovisioned 1
(present)
1/10 (not provisioned) unprovisioned Y Y Y Y 1
quad-pcm
1/11 quad-pcm unprovisioned Y Y Y Y 1
1/12 quad-pcm unprovisioned Y Y Y Y 1
pcp-server
pcp-server
Syntax
pcp-server
pcp-server server-name
pcp-server server-name statistics interface interface-name
pcp-server server-name statistics
Context
[Tree] (show>router pcp-server)
Full Context
show router pcp-server
Description
This command displays PCP server information.
Parameters
- server-name
-
Specifies the PCP server name, up to 32 characters.
- statistics
-
Displays PCP server statistics information.
- interface-name
-
Specifies the interface name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following outputs are examples of router PCP server information.
Output Example*A:Dut-C# show router 20 pcp-server "pcp-server-1"
===============================================================================
PCP server "pcp-server-1"
===============================================================================
Description : (Not Specified)
Administrative state : in-service
PCP server policy : pcp-policy-1
Forwarding Inside Router : 20
Dual Stack Lite address : af::1
State : in-service
State description : (Not Specified)
Epoch : 19684
Last management change : 04/07/2020 13:19:34
===============================================================================
Interfaces
-------------------------------------------------------------------------------
toDut-B-lag2
toLinux2
-------------------------------------------------------------------------------
No. of Interface(s): 2
*A:Dut-C# show router 20 pcp-server "pcp-server-1" statistics
===============================================================================
PCP statistics for interface "toDut-B-lag2"
===============================================================================
Rx opcode "announce" : 0
Rx opcode "map" : 0
Rx opcode "peer" : 0
Rx opcode "get" : 0
Rx opcode unknown : 0
Rx option "third party" : 0
Rx option "prefer failure" : 0
Rx option "filter" : 0
Rx option "description" : 0
Rx option "next" : 0
Rx option "port reservation" : 0
Rx option unknown : 0
Rx dropped (packet too short) : 0
Rx dropped (wrong r bit) : 0
Rx dropped (invalid source address) : 0
Rx dropped (oper down) : 0
Tx result "success" : 6
Tx result "unsupported version" : 0
Tx result "not authorized" : 0
Tx result "malformed request" : 0
Tx result "unsupported opcode" : 0
Tx result "unsupported option" : 0
Tx result "malformed option" : 0
Tx result "network failure" : 0
Tx result "no resources" : 0
Tx result "unsupported protocol" : 0
Tx result "user exceeded quota" : 0
Tx result "cannot provide external" : 0
Tx result "address mismatch" : 0
Tx result "no more mappings" : 0
Tx result "ambiguous" : 0
Tx v4 : 2
Tx v6 : 4
Tx dropped (tx error) : 0
===============================================================================
pcp-server
Syntax
pcp-server server-name interface interface-name statistics
Context
[Tree] (clear>router pcp-server)
Full Context
clear router pcp-server
Description
This command clears NAT PCP server data.
Parameters
- server-name
-
Clears NAT PCP server data for the specified PCP server, up to 32 characters.
- interface-name
-
Clears NAT PCP server data for the specified interface, up to 32 characters.
- statistics
-
Clears NAT PCP server statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
pcp-server
Syntax
pcp-server server-name
Context
[Tree] (tools>perform>router pcp-server)
Full Context
tools perform router pcp-server
Description
This command configures performance tools for a specified NAT port control policy server.
Parameters
- server-name
-
Specifies the PCP server name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
pcp-server-policy
pcp-server-policy
Syntax
pcp-server-policy
pcp-server-policy name
Context
[Tree] (show>service>nat pcp-server-policy)
Full Context
show service nat pcp-server-policy
Description
This command displays PCP server policy information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
pcs
pcs
Syntax
pcs[clear]
Context
[Tree] (tools>dump>port pcs)
Full Context
tools dump port pcs
Description
This command dumps the Physical Coding Sublayer (PCS) information for the port.
Platforms
All
peak
peak
Syntax
peak
peak application license-app
Context
[Tree] (show>system>license-statistics peak)
Full Context
show system license-statistics peak
Description
This command displays peak values of application license statistics.
Parameters
- license-app
-
Specifies the application license.
Platforms
VSR
peakvalue-stats
peakvalue-stats
Syntax
peakvalue-stats iom (slot | all) [recursive]
peakvalue-stats mda (mda | all) [recursive]
peakvalue-stats port (port-id | all)
peakvalue-stats pw-port (pw-port | all)
peakvalue-stats system [recursive]
peakvalue-stats service {svc-id | all} [ recursive]
peakvalue-stats service {svc-id} subscriber-interface { sub-itf | all} [recursive]
peakvalue-stats service {svc-id} group-interface { grp-itf | all}
Context
[Tree] (clear>subscriber-mgmt peakvalue-stats)
Full Context
clear subscriber-mgmt peakvalue-stats
Description
This command resets the most recent peak enhanced subscriber management counter per port, PW port, MDA, IOM, system, service, subscriber interface, or group interface.
Clearing one counter will not impact other counters. For example, clearing the most recent peak value for an IOM will not impact chassis peak value.
Parameters
- slot
-
Clears IOM host peak value statistics for the specified IOM.
- mda
-
Clears MDA host peak value statistics for the specified MDA.
- port-id
-
Clears port host peak value statistics for the specified port ID.
- pw-port
-
Clears pseudowire port host peak value statistics for the specified port.
- system
-
Clears system host peak value statistics.
- all
-
Clears all host peak value statistics.
- recursive
-
Resets the sub-level counters. For example, clearing IOM counters with the recursive keyword also clears counters of all port counters on that IOM.
- service svc-id
-
Clears service host peak value statistics for the specified service.
- subscriber-interface sub-itf
-
Clears subscriber interface host peak value statistics for the specified subscriber interface, up to 32 characters.
- group-interface grp-itf
-
Clears group interface host peak value statistics for the specified group interface, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
peer
peer
Syntax
peer [peer-profile profile-name] [local-address ip-address] [control protocol] [interface-type interface-type]
peer remote-address {ip-address | ipv6-address] [ udp-port port] [dsm-local-ip-address {ip-address | ipv6-address}
peer remote-address {ip-address | ipv6-address] [ udp-port port] statistics [dsm-local-ip-address { ip-address | ipv6-address}
Context
[Tree] (show>router>gtp peer)
Full Context
show router gtp peer
Description
This command displays GTP peer information.
Parameters
- profile-name
-
Specifies the name that identifies the profile.
- ip-address
-
Specifies the local IP address.
- protocol
-
Specifies the control plane protocol used for the connection with this Mobile Gateway.
- interface-type
-
Specifies the interface type used in the context of this peer.
- ip-address
-
Specifies the remote IP address.
- port
-
Specifies the UDP port.
- statistics
-
Displays statistics information about the Mobile Gateways connected to this system.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of peer GTP information.
Output ExampleNode# show router 10 gtp peer
===============================================================================
Peers
===============================================================================
Remote address : 192.168.100.1
UDP port : 2123
-------------------------------------------------------------------------------
State : up
Local address : 192.0.2.10
Profile : default_s11
Control protocol : gtpv2-c
Interface type : s11
Restart count : 1
Time : 2018/05/31 11:12:59
-------------------------------------------------------------------------------
No. of Peers: 1
===============================================================================
peer
Syntax
peer remote-address ip-address [remote-udp-port port]
peer remote-address ip-address [remote-udp-port port] statistics
Context
[Tree] (clear>router>gtp peer)
Full Context
clear router gtp peer
Description
This command clears all states for a given peer in this routing context. The system no longer sends keep-alive messages to the peer, and all active sessions are terminated.
If the optional statistics parameter is specified, only the peer statistics are cleared and all sessions remain.
Parameters
- ip-address
-
Specifies the IP address of the peer.
- port
-
Specifies the UDP port used by the peer.
- statistics
-
Specifies to clear only the peer statistics with all sessions remaining active.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
peer
Syntax
peer ip-address [udp-port port] [ip]
peer ip-address statistics [ udp-port port] [ip]
peer [draining] [{blacklisted | selectable | unreachable}]
Context
[Tree] (show>router>l2tp peer)
Full Context
show router l2tp peer
Description
This command displays information regarding all configured L2TP peers.
If this command is executed without specifying a peer IP address, then a list of all L2TP peers are listed along with the type of transport used and statistics on the total number of tunnels and sessions, as well as the number of active tunnels and sessions.
If this command is executed with a specific peer IP address, then a detailed view for that peer is displayed.
Parameters
- ip-address
-
Specifies the L2TP peer address.
- port
-
Specifies the UDP port for the L2TP peer. This parameter is only supported with L2TPv2 peers.
- ip
-
Displays peers using IP transport.
- statistics
-
Displays the statistics for the given IP address.
- draining
-
Displays only peers with draining tunnels.
- blacklisted
-
Displays peers that are denylisted.
- selectable
-
Displays peers that are selectable.
- unreachable
-
Displays peers that are deemed unreachable.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of L2TP peer operational information.
Output ExampleA:Dut-A# show router 200 l2tp peer
===============================================================================
L2TP Peers
===============================================================================
Peer IP Port Tun Active Ses Active
Drain Reachability Tun Total Ses Total
-------------------------------------------------------------------------------
10.1.1.2 ip 1 1
1 1
-------------------------------------------------------------------------------
No. of peers: 1
===============================================================================
A:Dut-A# show router 200 l2tp peer 10.1.1.2 ip
===============================================================================
Peer IP: 10.1.1.2
===============================================================================
Roles capab/actual: LAC LNS / - - Draining : false
Tunnels : 1 Tunnels Active : 1
Sessions : 1 Sessions Active : 1
Reachability : reachable Time Unreachable : N/A
===============================================================================
Conn ID Loc-Tu-ID Rem-Tu-ID State Blacklist-state Ses Active
Group Ses Total
Assignment
-------------------------------------------------------------------------------
221118464 3374 0 established not-blacklisted 1
v3-group-1 1
tun-1-l2tp-v3
-------------------------------------------------------------------------------
No. of tunnels: 1
===============================================================================
*A:Fden-Dut2-BSA2# show router l2tp peer 10.0.0.1 statistics
===============================================================================
Peer IP: 10.0.0.1
===============================================================================
tunnels : 1
tunnels active : 1
sessions : 1
sessions active : 1
rx ctrl octets : 541
rx ctrl packets : 5
tx ctrl octets : 272
tx ctrl packets : 5
tx error packets : 0
rx error packets : 0
rx accepted msg : 4
rx duplicate msg : 0
rx out of window msg : 0
acceptedMsgType
StartControlConnectionRequest : 1
StartControlConnectionConnected : 1
IncomingCallRequest : 1
IncomingCallConnected : 1
ZeroLengthBody : 1
originalTransmittedMsgType
StartControlConnectionReply : 1
IncomingCallReply : 1
ZeroLengthBody : 3
last cleared time : N/A
===============================================================================
peer
Syntax
peer ip-address [udp-port port]
peer ip-address statistics [udp-port port]
peer [draining] [blacklisted | selectable | unreachable]
Context
[Tree] (show>router>l2tp peer)
Full Context
show router l2tp peer
Description
This command displays L2TP peer operational information.
Parameters
- ip-address
-
Specifies the IP dress for the L2TP peer.
- port
-
Specifies the local UDP port of this L2TP.
- draining
-
Specifies to display information about the L2TP peer being drained.
- blacklisted
-
Specifies to display information about the peer has been deemed unreachable and has been put in the tunnel selection denylist.
- selectable
-
Specifies to display information about the peer has been deemed unreachable for the time specified in tmnxL2tpXtTuSelBlacklistMaxTime and can now be selected for a single session, after which the reachability of the peer is reevaluated.
- unreachable
-
Specifies to display information about the sysUpTime when the peer was deemed unreachable for the last time.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of L2TP peer information.
Output Exampleshow router l2tp peer 10.100.0.2
===============================================================================
Peer IP: 10.100.0.2
===============================================================================
Roles capab/actual: LAC LNS /LAC - Draining : false
Tunnels : 1 Tunnels Active : 0
Sessions : 1 Sessions Active : 0
Reachability : blacklisted Time Unreachable : 01/31/2013 08:55:06
Time Blacklisted : 01/31/2013 08:55:06 Remaining (s) : 34
===============================================================================
Conn ID Loc-Tu-ID Rem-Tu-ID State Ses Active
Group Ses Total
Assignment
-------------------------------------------------------------------------------
977207296 14911 0 closed 0
base_lac_base_lns 1
t1
-------------------------------------------------------------------------------
No. of tunnels: 1
===============================================================================
show router l2tp tunnel detail
===============================================================================
L2TP Tunnel Status
==============================================================================
Connection ID: 831782912
State : closedByPeer
IP : 10.0.0.1
Peer IP : 10.100.0.2
Tx dst-IP : 10.100.0.2
Rx src-IP : 10.100.0.2
Name : lac
Remote Name :
Assignment ID: t1
Group Name : base_lac_base_lns
Acct. Policy : l2tp-base
Error Message: N/A
Remote Conn ID : 4294901760
Tunnel ID : 12692 Remote Tunnel ID : 65535
UDP Port : 1701 Remote UDP Port : 1701
Preference : 50 Receive Window : 64
Hello Interval (s): 300
Idle TO (s) : 5 Destruct TO (s) : 60
Max Retr Estab : 5 Max Retr Not Estab: 5
Session Limit : 32767 AVP Hiding : sensitive
Transport Type : udpIp Challenge : never
Time Started : 01/31/2013 08:56:58 Time Idle : 01/31/2013 08:56:58
Time Established : N/A Time Closed : 01/31/2013 08:56:58
Stop CCN Result : reqShutDown General Error : noError
Blacklist-state : blacklisted
Blacklist Time : 01/31/2013 08:56:58 Remaining (s) : 49
-------------------------------------------------------------------------------
No. of tunnels: 1
===============================================================================
peer
Syntax
peer ip-address [udp-port port] [ip]
Context
[Tree] (clear>router>l2tp peer)
Full Context
clear router l2tp peer
Description
This command clears L2TP peer data.
Parameters
- ip-address
-
Clears the peers associated with the specified IP address.
- port
-
Clears the peers associated with the specified UDP port.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
peer
Syntax
peer ip-address [udp-port port] [ip]
Context
[Tree] (tools>perform>router>l2tp peer)
Full Context
tools perform router l2tp peer
Description
This command configures performance tools for an L2TP peer.
Parameters
- ip-address
-
Specifies the IP address of the L2TP peer.
- port
-
Specifies the UDP port for the L2TP peer. This parameter is only supported with L2TPv2 peers.
- ip
-
Enables performance tools for peers using IP transport.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
peer
Syntax
peer [ip-int-name]
Context
[Tree] (show>router>rip peer)
Full Context
show router rip peer
Description
This command displays RIP peer information.
Parameters
- ip-int-name
-
Displays peer information for the specified IP peer interface name, up to 32 characters.
Platforms
All
Output
RIP Peer Output Fields describes the command output fields for a RIP peer.
|
Label |
Description |
|---|---|
|
Peer IP Addr |
The IP address of the peer router. |
|
Interface Name |
The peer interface name. |
|
Version |
The version of RIP running on the peer. |
|
Last Update |
The number of days since the last update. |
|
No. of Peers |
The number of RIP peers. |
The following output is an example of RIP peer information.
Output ExampleA:ALA-A# show router rip peers
===============================================================================
RIP Peers
===============================================================================
Peer IP Addr Interface Name Version Last Update
-------------------------------------------------------------------------------
10.0.5.13 router-2/2 RIPv2 0
10.0.6.16 router-2/3 RIPv2 2
10.0.9.14 router-2/5 RIPv2 8
10.0.10.15 router-2/4 RIPv2 0
-------------------------------------------------------------------------------
No. of Peers: 4
===============================================================================
A:ALA-A#
peer
Syntax
peer [ip-address] [statistics]
Context
[Tree] (clear>router>ldp peer)
Full Context
clear router ldp peer
Description
This command restarts or clears statistics for LDP targeted peers.
Parameters
- ip-address
-
The IP address of a targeted peer.
- statistics
-
Clears only the statistics for a targeted peer.
Platforms
All
peer
Syntax
peer ip-address
Context
[Tree] (tools>dump>router>ldp peer)
Full Context
tools dump router ldp peer
Description
This command dumps information for an LDP peer.
Platforms
All
peer
Syntax
peer [ip-address] [detail]
Context
[Tree] (show>router>pcep>pcc peer)
Full Context
show router pcep pcc peer
Description
This command displays the PCEP peer information.
Parameters
- ip-address
-
Specifies the IP address.
- detail
-
Specifies detailed information.
Platforms
All
Output
PCEP Peer Output
PCEP Peer Output Fields describes PCEP Peer output fields.
Output Example*A:cses-V23# show router pcep pcc peer
===============================================================================
PCEP Path Computation Client (PCC) Peer Info
===============================================================================
IP Address : 192.168.0.10
Admin Status : Down Oper Status : Down
Peer Capabilities : (Not Specified)
Speaker ID : (Undefined)
Sync State : not-initialized Peer Overloaded : False
Session Establish Time: 0d 00:00:00
Oper Keepalive : N/A Oper DeadTimer : N/A
===============================================================================
|
Label |
Description |
|---|---|
|
IP Address |
Specifies the IP address. |
|
Peer Capabilities |
Specifies the peer capabilities. |
|
Speaker ID |
Specifies the sender IP address. |
|
Sync State |
Specifies the synchronization state. |
|
Peer Overload |
Specifies the peer overload. |
|
Session Establish Time |
Specifies the session establish time. |
|
Oper Keepalive |
Specifies the operational keepalive value. |
|
Oper DeadTimer |
Specifies the operational dead timer value. |
peer
Syntax
peer [ip-address] [group group-name] [detail]
Context
[Tree] (show>router>msdp peer)
Full Context
show router msdp peer
Description
This command displays information about an MSDP peer.
Parameters
- ip-address
-
Displays information about the specified IP address. If no IP address specified, information about all MSDP IP addresses display.
- group group-name
-
Displays information about the specified group name, up to 32 characters. If no group-name is specified, information about all MSDP peers display.
- detail
-
Keyword to displays detailed MSDP peer information.
Platforms
All
Output
The following output is an example of MSDP peer information, and Output fields: MSDP peer describes the output fields.
Output exampleA:ALA-48# show router msdp peer
=============================================================================
MSDP Peers
=============================================================================
Peer Local Address State Last State Change SA Learnt
-----------------------------------------------------------------------------
10.20.1.1 10.20.1.6 Established 08/30/2002 03:22:131008
-----------------------------------------------------------------------------
Peers : 1
=============================================================================
A:ALA-48#
A:ALA-48# show router msdp peer detail
===============================================================================
MSDP Peers
-------------------------------------------------------------------------------
Peer Address : 10.20.1.1
-------------------------------------------------------------------------------
Group Name : None
Local Address : 10.20.1.6
Last State Change : 08/30/2002 03:22:13 Last Act Src Limit : N/A
Peer Admin State : Up Default Peer : No
Peer Connect Retry : 0 State : Established
SA accepted : 1008 SA received : 709
State timer expires: 18 Peer time out : 62
Active Source Limit: None Receive Msg Rate : 0
Receive Msg Time : 0 Receive Msg Thd : 0
Auth Status : Disabled Auth Key : None
Export Policy : None Specified / Inherited
Import Policy : None Specified / Inherited
-------------------------------------------------------------------------------
Peers : 1
===============================================================================
A:ALA-48#
|
Label |
Description |
|---|---|
|
Peer |
The IP address of the peer |
| Group Name | The name of the group associated with the peer |
|
Local Address |
The local IP address |
|
State |
The current state of the peer |
|
Last State Change |
The date and time of the last state change of the peer |
| Last Act Src Limit | The date and time when the active source limit was reached for messages received by the peer |
|
SA Learnt |
The number of SAs learned through a peer |
|
Peer Admin State |
The administrative state of the MSDP peer |
| Default Peer | The default peer configuration status |
| Peer connect retry | The number of connection attempts to the peer |
| SA accepted | The number of SA messages accepted from the peer |
| SA received | The total number of SA messages received from the peer |
| Active Source Limit | The active source message limit |
|
Receive Msg Rate |
The rate that the messages are read from the TCP session |
|
Receive Msg Time |
The time of MSDP messages that are read from the TCP session within the configured number of seconds |
|
Receive Msg Thd |
The configured threshold number of MSDP messages that can be processed before the MSDP message rate limiting function |
| Auth status |
The authentication status of the peer |
| Auth Key | The authentication key for the peer |
| Export Policy |
The export policy specified for the group |
| Import Policy |
The import policy specified for the group |
peer
Syntax
peer ip-address [router router-instance | service-name service-name] [detail]
Context
[Tree] (show>system>ptp peer)
Full Context
show system ptp peer
Description
This command displays PTP information for a specific peer.
Parameters
- ip-address
-
Specifies the IPv4 or IPv6 address.
- router-instance
-
Displays the information for the specified router instance.
- service-name
-
Specifies the service name, up to 64 characters, used to identify the router instance.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of IPv6 peer information and Output fields: PTP peer describes the output fields.
Output Exampleshow system ptp peer router===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router : 5
IP Address : 1111:2222:3333:4444:5555:70:1:4
Announce Direction: rx+tx
Admin State : up G.8275 Priority : 128
Sync Interval : 64 pkt/s
Local PTP Port : 1 PTP Port State : master
Clock Id : ac5dfffffe000000 Remote PTP Port : 2
GM Clock Id : ac5cfffffe000000 GM Clock Class : 6
GM Clock Accuracy : within 100 ns GM Clock Variance : 0x4e5d (1.8E-15)
GM Clock Priority1: 128 GM Clock Priority2 : 128
Steps Removed : 1 Parent Clock : no
Tx Timestamp Point: port Rx Timestamp Point : port
Last Tx Port : 1/4/2 Last Rx Port : 1/4/2
Port Asymmetry : 0 ns Port Asymmetry : 0 ns
Best Master : no Parent Clock : no
Backup Source : yes
APTS Asymmetry : +140 ns Last Calc : 2023/05/29 13:57:36
Profile Name : Primary
Profile : ITU-T G.8275.2 Domain : 44
===============================================================================
The following output is an example of detailed IPv6 peer information and Output fields: PTP peer describes the output fields.
Output Exampleshow system ptp peer router detail==============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router Instance : 5
IP Address : 1111:2222:3333:4444:5555:70:1:4
Announce Direction : rx+tx
Admin State : up G.8275 Priority : 128
Sync Interval : 64 pkt/s
Local PTP Port : 1 PTP Port State : master
Clock Id : ac5dfffffe000000 Remote PTP Port : 2
GM Clock Id : ac5cfffffe000000 GM Clock Class : 6
GM Clock Accuracy : within 100 ns GM Clock Variance : 0x4e5d (1.8E-15)
GM Clock Priority1: 128 GM Clock Priority2 : 128
Steps Removed : 1 Parent Clock : no
Tx Timestamp Point: port Rx Timestamp Point : port
Last Tx Port : 1/4/2 Last Rx Port : 1/4/2
Port Asymmetry : 0 ns Port Asymmetry : 0 ns
Best Master : no Parent Clock : no
Backup Source : yes
APTS Asymmetry : +140 ns Last Calc : 2023/05/29 13:57:36
Profile Name : Primary
Profile : ITU-T G.8275.2 Domain : 44
===============================================================================
===============================================================================
IEEE 1588/PTP Unicast Negotiation Information
===============================================================================
IP Address
Dir Type Rate Duration State Time
-------------------------------------------------------------------------------
1111:2222:3333:4444:5555:70:1:4
Rx Announce 1 pkt/2 s 300 Granted 09/01/2010 17:23:04
1111:2222:3333:4444:5555:70:1:4
Tx Announce 1 pkt/2 s 300 Granted 09/01/2010 17:23:04
===============================================================================
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
PTP Packets 253 11
Announce 243 1
Sync 0 0
Follow Up 0 0
Delay Request 0 0
Delay Response 0 0
Signaling 10 10
Request TLVs 6 4
Announce 6 4
Sync 0 0
Delay Response 0 0
Grant TLVs (Granted) 4 6
Announce 4 6
Sync 0 0
Delay Response 0 0
Grant TLVs (Rejected) 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Cancel TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Ack Cancel TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Other TLVs 0 0
Other 0 0
Discards 0 0
Bad PTP domain 0 0
Alternate Master 0 0
Out Of Sequence 0 0
Peer Disabled 0 0
Other 0 0
================================================================================
The following output is an example of detailed IPv4 peer information and Output fields: PTP peer describes the output fields.
Output Exampleshow system ptp peer router detail===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router Instance : 5
IP Address : 6.1.1.2
Announce Direction: rx
Admin State : up G.8275 Priority : 128
Sync Interval : 64 pkt/s
Local PTP Port : 2 PTP Port State : master
Clock Id : ac5dfffffe000000 Remote PTP Port : 2
GM Clock Id : ac5cfffffe000000 GM Clock Class : 6
GM Clock Accuracy : within 100 ns GM Clock Variance : 0x4e5d (1.8E-15)
GM Clock Priority1: 128 GM Clock Priority2 : 128
Steps Removed : 0
Tx Timestamp Point: port Rx Timestamp Point : port
Last Tx Port : 1/1/2 Last Rx Port : 1/1/2
Port Asymmetry : 0 ns Port Asymmetry : 0 ns
Best Master : no Parent Clock : no
Backup Source : yes
APTS Asymmetry : +140 ns Last Calc : 2023/05/29 13:57:36
Profile Name : Primary
Profile : ITU-T G.8275.2 Domain : 44
===============================================================================
===============================================================================
IEEE 1588/PTP Unicast Negotiation Information
===============================================================================
IP Address Dir Type Rate Duration State Time
-------------------------------------------------------------------------------
6.1.1.2 Rx Announce 1 pkt/2 s 300 Granted 09/01/2010 17:23:04
6.1.1.2 Tx Announce 1 pkt/2 s 300 Granted 09/01/2010 17:23:04
===============================================================================
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
PTP Packets 253 11
Announce 243 1
Sync 0 0
Follow Up 0 0
Delay Request 0 0
Delay Response 0 0
Signaling 10 10
Request TLVs 6 4
Announce 6 4
Sync 0 0
Delay Response 0 0
Grant TLVs (Granted) 4 6
Announce 4 6
Sync 0 0
Delay Response 0 0
Grant TLVs (Rejected) 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Cancel TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Ack Cancel TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Other TLVs 0 0
Other 0 0
Discards 0 0
Bad PTP domain 0 0
Alternate Master 0 0
Out Of Sequence 0 0
Peer Disabled 0 0
Other 0 0
================================================================================
|
Label |
Description |
|---|---|
|
IEEE 1588/PTP Peer Information |
|
|
Router |
The name of the router instance |
|
IP Address |
The IP address of the PTP peer |
|
Announce Direction Anno Flow |
The direction from which PTP announce messages were sent or received |
|
Admin State |
The administrative state of the PTP peer |
|
G.8265.1 Priority |
The priority used in the best master clock algorithm (BMCA) for the local PTP port when the clock profile is G.8265.x |
|
G.8275 Priority |
The priority used in the BTCA for the local port when the clock profile is G.8275.1 or G.8275.2 |
|
Sync Interval |
The message rate for Sync messages for this peer |
|
Local PTP Port |
The number of local PTP ports |
|
PTP Port State |
The state of the PTP port |
|
Clock Id |
The clockIdentity value of the local PTP clock |
|
Remote PTP Port |
The number of remote PTP ports |
|
GM Clock Id |
The clockIdentity value of the grandmaster clock advertised by the parent clock |
|
GM Clock Class |
The clockClass value of the grandmaster clock advertised by the parent clock |
|
GM Clock Accuracy |
The clockAccuracy value of the grandmaster clock advertised by the parent clock |
|
GM Clock Variance |
The offsetScaledLogVariance value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority1 |
The priority1 value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority2 |
The priority2 value of the grandmaster clock advertised by the parent clock |
|
Steps Removed |
The number of steps removed the PTP peer is from a grandmaster clock |
|
Parent Clock |
Indicates if this is the parent clock. May differ from the Best Master if there is a local GNSS. |
| Tx Timestamp Point |
The transmit timestamp point |
|
Rx Timestamp Point |
The receive timestamp point |
|
Last Tx Port |
The port-id of the last port from which a synchronization packet was transmitted |
|
Last Rx Port |
The port-id of the last port into which a synchronization packet was received |
|
Port Asymmetry |
The configured asymmetry for the port (either Tx or Rx port) |
| Best Master |
Indicates if this peer was selected as the best master clock by the BTCA |
|
Backup Source |
Indicates if this port is operating as a backup slave to the parent clock |
| APTS Asymmetry | The asymmetry computed by the backup source. This is used to compensate if the clock switches to this backup. |
|
Offset from LclClk |
The offset from master computed by the PTP source. This is the difference between the backup PTP source and the local clock set by the GNSS. This is similar to APTS Asymmetry but when using G.8275.1 profile. |
|
Last Calc |
The date and time at which the APTS Asymmetry or Offset from LclClk was last updated |
|
Profile Name |
The profile in use with this peer |
|
Profile |
The underlying standard profile used in the profile identified by profile name |
|
Domain |
The domain number used for this peer |
|
IEEE 1588/PTP Unicast Negotiation Information |
|
|
Dir |
The direction (transmitted or received) of the unicast negotiation packet |
|
Type |
The unicast negotiation packet type |
|
Rate |
The rate of packet transmission or reception |
|
Duration |
The duration of the packet transmission or reception interval, in seconds |
|
State |
The state of the negotiation |
|
Time |
The date and time that the negotiation state was changed |
|
IEEE 1588/PTP Packet Statistics |
|
|
Input |
The number of input packets within the specified category |
|
Output |
The number of output packets within the specified category |
peer
Syntax
peer ip-address [detail]
Context
[Tree] (show>service>id>ptp peer)
Full Context
show service id ptp peer
Description
This command displays PTP information for a specific peer.
Parameters
- ip-address
-
Specifies the IP address.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following command displays PTP information for a single peer and Output fields: service PTP peer describes the output fields.
show service id ptp peer detail===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router Instance : 5
IP Address : 6.1.1.2 Announce Direction : rx+tx
Admin State : up G.8265.1 Priority : n/a
Sync Interval : 64 pkt/s
Local PTP Port : 2 PTP Port State : passive
Clock Id : ac5dfffffe000000 Remote PTP Port : 2
GM Clock Id : ac5cfffffe000000 GM Clock Class : 13
GM Clock Accuracy : 0xfe (unknown) GM Clock Variance : ffff (not computed)
GM Clock Priority1: 128 GM Clock Priority2 : 128
Steps Removed : 1 Parent Clock : no
Tx Timestamp Point: port Rx Timestamp Point : port
Last Tx Port : 1/1/2 Last Rx Port : 1/1/2
===============================================================================
===============================================================================
IEEE 1588/PTP Unicast Negotiation Information
===============================================================================
IP Address Dir Type Rate Duration State Time
-------------------------------------------------------------------------------
6.1.1.2 Rx Announce 1 pkt/2 s 300 Granted 09/01/2010 17:23:04
6.1.1.2 Tx Announce 1 pkt/2 s 300 Granted 09/01/2010 17:23:04
===============================================================================
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
PTP Packets 253 11
Announce 243 1
Sync 0 0
Follow Up 0 0
Delay Request 0 0
Delay Response 0 0
Signaling 10 10
Request TLVs 6 4
Announce 6 4
Sync 0 0
Delay Response 0 0
Grant TLVs (Granted) 4 6
Announce 4 6
Sync 0 0
Delay Response 0 0
Grant TLVs (Rejected) 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Cancel TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Ack Cancel TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Other TLVs 0 0
Other 0 0
Discards 0 0
Bad PTP domain 0 0
Alternate Master 0 0
Out Of Sequence 0 0
Peer Disabled 0 0
Other 0 0
================================================================================
| Label | Description |
|---|---|
|
IEEE 1588/PTP Peer Information |
|
|
Router |
The name or ID of the router instance |
|
IP Address |
The IP address of the PTP peer |
|
Announce Direction |
The configured directions (transmit, receive, or both) for Announce messages |
|
Admin State |
The administrative state of the PTP peer |
|
G.8265.1 Priority |
Displays if the G.8265.1 profile has priority |
|
Local PTP Port |
The local PTP port number |
|
PTP Port State |
The PTP port state |
|
Clock ID |
The ID of the referenced clock |
|
Remote PTP Port |
The remote PTP port number |
|
GM Clock Id |
The clockIdentity value of the grandmaster clock advertised by the parent clock |
|
GM Clock Class |
The clockClass value of the grandmaster clock advertised by the parent clock |
|
GM Clock Accuracy |
The clockAccuracy value of the grandmaster clock advertised by the parent clock |
|
GM Clock Variance |
The offsetScaledLogVariance value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority1 |
The priority1 value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority2 |
The priority2 value of the grandmaster clock advertised by the parent clock |
|
Steps Removed |
The number of steps removed the PTP peer is from a grandmaster clock |
|
Parent Clock |
Displays whether a parent clock is referenced |
|
IEEE 1588/PTP Unicast Negotiation Information |
|
|
IP Address |
The IP address of the PTP peer |
|
Dir |
The direction (transmitted or received) of the unicast negotiation packet |
|
Type |
The unicast negotiation packet type |
|
Rate |
The rate of packet transmission or reception |
|
Duration |
The duration of the packet transmission or reception interval, in seconds |
|
State |
The state of the negotiation |
|
Time |
The date and time that the negotiation state was changed |
|
IEEE 1588/PTP Packet Statistics |
|
|
Input |
The number of input packets within the specified category |
|
Output |
The number of output packets within the specified category |
|
PTP Packets |
The total number of PTP packets across all PTP packet categories |
|
Announce |
The number of PTP Announce packets |
|
Sync |
The number of PTP Sync packets |
|
Follow Up |
The number of PTP Follow Up packets |
|
Delay Request |
The number of PTP Delay Request packets |
|
Delay Response |
The number of PTP Delay Response packets |
|
Signaling |
The number of PTP signaling packets |
|
Request TLVs |
The total number of Request TLV packets of all types (Announce, Sync, and Delay Response) |
|
Grant TLVs (Granted) |
The total number of granted Grant TLV packets of all types (Announce, Sync, and Delay Response) |
|
Grant TLVs (Rejected) |
The total number of rejected Grant TLV packets of all types (Announce, Sync, and Delay Response) |
|
Cancel TLVs |
The total number of Cancel TLV packets of all types (Announce, Sync, and Delay Response) |
|
Ack Cancel TLVs |
The total number of Ack Cancel TLV packets of all types (Announce, Sync, and Delay Response) |
|
Announce |
The number of Announce packets of the specified TLV category |
|
Sync |
The number of Sync packets of the specified TLV category |
|
Delay Response |
The number of Delay Response packets of the specified TLV category |
|
Other TLVs |
The total number of other TLV packets that do not match the other categories or types |
|
Other |
The number of PTP packets that do not match the other categories or types |
|
Discards |
The total number of discarded packets across all categories |
|
Bad PTP domain |
The number of packets discarded because of a bad PTP domain |
|
Alternate Master |
The number of packets discarded because of an alternate master being referenced |
|
Out of Sequence |
The number of out-of-sequence packets discarded |
|
Peer Disabled |
The number of packets discarded because of the peer being disabled |
|
Other |
The number of packets discarded for reasons not matching the other categories or types |
peer
Syntax
peer ip-address
Context
[Tree] (clear>redundancy>multi-chassis>mcr>statistics peer)
Full Context
clear redundancy multi-chassis mc-ring statistics peer
Description
This command clears multi-chassis ring peer statistics.
Parameters
- ip-address
-
Clears ring peer statistics for the specified IP address.
Platforms
All
peer
Syntax
peer ip-address [router router-instance | service name service-name] statistics
Context
[Tree] (clear>system>ptp peer)
Full Context
clear system ptp peer
Description
This command clears PTP peer information.
Parameters
- ip-address
-
Specifies the IPv4 or IPv6 address.
- router-instance
-
Clears information that is specific to a virtual router instance, up to 32 characters.
- service-name
-
Clears information that is specific to a service name, up to 64 characters.
- statistics
-
Clears statistics information of the specified IP address.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
peer
Syntax
peer [ip-int-name]
Context
[Tree] (show>router>ripng peer)
Full Context
show router ripng peer
Description
This command displays RIPng peer information.
Parameters
- ip-int-name
-
Displays peer information for peers on the specified IPv6 interface.
Platforms
All
Output
The following output is an example of RIPng peer information.
Output Example*A:Dut-C>config>router>if# show router ripng peer
===============================================================================
RIP-NG Peers
===============================================================================
Peer IP Addr Version Last Update
Interface Name
-------------------------------------------------------------------------------
fe80::6629:ffff:fe00:0 ripNg-v1 0
one
fe80::6629:ffff:fe00:0 ripNg-v1 0
two
fe80::6629:ffff:fe00:0 ripNg-v1 0
three
fe80::6629:ffff:fe00:0 ripNg-v1 0
four
-------------------------------------------------------------------------------
No. of Peers: 4
===============================================================================
*A:Dut-C>config>router>if# show router ripng peer "one"
===============================================================================
RIP-NG Peers
===============================================================================
Peer IP Addr Version Last Update
Interface Name
-------------------------------------------------------------------------------
fe80::6629:ffff:fe00:0 ripNg-v1 0
one
-------------------------------------------------------------------------------
No. of Peers: 1
===============================================================================
peer
Syntax
peer [peer-address {ip-address | ipv6-address}] [router router-instance] [ local-address {ip-address | ipv6-address}]
Context
[Tree] (show>subscr-mgmt>pfcp peer)
Full Context
show subscriber-mgmt pfcp peer
Description
This command displays connectivity details for a specific PFCP connection to a peer and the PFCP association to which the peer is linked. Multiple connections can exist per PFCP association.
Parameters
- ip-address
-
Specifies the peer or local IPv4 address.
- ipv6-address
-
Specifies the peer or local IPv6 address.
- router-instance
-
Specifies the identifier of the router where the peer is terminated.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of output of the show subscriber-mgmt PFCP peer command.
Output ExampleA:BNG-UPF# show subscriber-mgmt pfcp peer
===============================================================================
PFCP Peers
===============================================================================
Peer router : 990002
Peer Address : 17.17.17.10
Local Address : 192.0.2.11
Association : bng-cpf
Path Mgmt State : up
Restoration Timer Expiry : (Not Specified)
Restart Reason : none
===============================================================================
No. of PFCP Peers: 1
===============================================================================
peer
Syntax
peer ip-address statistics
Context
[Tree] (clear>service>id>ptp peer)
Full Context
clear service id ptp peer
Description
This command clears PTP peer information.
Parameters
- ip-address
-
Specifies the IP address.
- statistics
-
Clears statistics information of the specified peer.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
peer
Syntax
peer [ip-address] statistics
Context
[Tree] (clear>router>pcep>pcc peer)
Full Context
clear router pcep pcc peer
Description
This command clears PCEP PCC peer statistics.
Parameters
- ip-address
-
Specifies the IP address.
- statistics
-
Clears PCEP PCC peer statistics.
Platforms
All
peer-profile
peer-profile
Syntax
peer-profile [profile-name]
peer-profile profile-name associations
Context
[Tree] (show subscr-mgmt gtp peer-profile)
Full Context
show subscriber-mgmt gtp peer-profile
Description
This command displays GTP peer profile information.
Parameters
- profile-name
-
Specifies the name that identifies the profile.
- associations
-
Specifies the associated contexts for the specified peer profile.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of GTP peer profile information.
Output ExampleNode# show subscriber-mgmt gtp peer-profile
===============================================================================
GTP peer profiles
===============================================================================
Name Description
-------------------------------------------------------------------------------
default (Not Specified)
default_s11 (Not Specified)
-------------------------------------------------------------------------------
No. of profiles: 2
===============================================================================
Node# show subscriber-mgmt gtp peer-profile "default_s11"
===============================================================================
GTP peer profile "default_s11"
===============================================================================
Description : (Not Specified)
Retransmit timeout (s) : 5
Retransmit retries : 3
Keepalive interval (s) : 60
Keepalive retries : 4
Keepalive retry timeout (s) : 5
Time to live : 255
IPv4 MTU : 1400
Interface type : s11
Charging char home UE : (None)
Charging char roaming UE : (None)
Session hold time (s) : 30
Report WLAN location : disabled
Procotol Config Options I.E.: pco
Python policy : (Not Specified)
Radio Access Technology type: wlan
Last management change : 05/31/2018 11:05:46
GGSN uplink GBR (Kbps) : 5000
GGSN uplink MBR (Kbps) : 5000
GGSN downlink GBR (Kbps) : 2000
GGSN downlink MBR (Kbps) : 2000
GGSN Alloc/Retention Prio : 1
GGSN uplink AMBR (Kbps) : (Not Specified)
GGSN downlink AMBR (Kbps) : (Not Specified)
GGSN last management change : 05/31/2018 11:05:46
PGW uplink GBR (Kbps) : 0
PGW uplink MBR (Kbps) : 0
PGW downlink GBR (Kbps) : 0
PGW downlink MBR (Kbps) : 0
PGW Alloc/Retention Prio : 1
PGW Qos Class ID : 8
PGW uplink AMBR (Kbps) : 10000
PGW downlink AMBR (Kbps) : 20000
PGW last management change : 05/31/2018 11:05:46
MME uplink GBR (Kbps) : 0
MME uplink MBR (Kbps) : 0
MME downlink GBR (Kbps) : 0
MME downlink MBR (Kbps) : 0
MME Alloc/Retention Prio : 1
MME Qos Class ID : 8
MME uplink AMBR (Kbps) : 10000
MME downlink AMBR (Kbps) : 20000
MME last management change : 05/31/2018 11:05:46
===============================================================================
peer-profile-map
peer-profile-map
Syntax
peer-profile-map
Context
[Tree] (show>router>gtp>s11 peer-profile-map)
Full Context
show router gtp s11 peer-profile-map
Description
This command displays the peer profile mapping that is used to connect to S11 peers.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of GTP peer profile map information.
Output ExampleNode# show router 20 gtp s11 peer-profile-map
===============================================================================
Peer profile map
===============================================================================
Address prefix Profile
-------------------------------------------------------------------------------
0.0.0.0/0 default_s11
192.2.0.0/24 specific_profile
-------------------------------------------------------------------------------
No. of address prefixes: 2
===============================================================================
peer-profile-map
Syntax
peer-profile-map
Context
[Tree] (show>router>gtp>uplink peer-profile-map)
Full Context
show router gtp uplink peer-profile-map
Description
This command displays the peer profile map.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
peers
peers
Syntax
peers [router router-instance | service-name service-name] [detail]
Context
[Tree] (show>system>ptp peers)
Full Context
show system ptp peers
Description
This command displays summary information for all the PTP peers.
Parameters
- router-instance
-
Displays only the information for a specific router instance.
- service-name
-
Specifies the service name, up to 64 characters, used to identify the router instance.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following command displays PTP peers information and Output fields: PTP peers describes the output fields.
show system ptp peers===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router
IP Address
Anno Flow Admin State PTP Port State Parent Clock
-------------------------------------------------------------------------------
Base
1.4.1.21
tx n/a master no
1
1111:2222:3333:4444:5555:70:1:4
rx+tx up master no
1111:2222:3333:4444:5555:70:1:5
rx up slave yes
2
1.1.1.21
tx n/a master no
-------------------------------------------------------------------------------
No. of PTP Peers: 4
===============================================================================
The following command displays PTP peers router information and Output fields: PTP peers describes the output fields.
show system ptp peers router Base===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router
IP Address
Anno Flow Admin State PTP Port State Parent Clock
-------------------------------------------------------------------------------
Base
1.4.1.21
tx n/a master no
-------------------------------------------------------------------------------
No. of PTP Peers: 1
===============================================================================
The following command displays PTP peers router information and Output fields: PTP peers describes the output fields.
show system ptp peers router===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router
IP Address Anno Flow Admin State PTP Port State Parent Clock
-------------------------------------------------------------------------------
1
1111:2222:3333:4444:5555:70:1:4
rx+tx up master no
1111:2222:3333:4444:5555:70:1:5
rx up slave yes
-------------------------------------------------------------------------------
No. of PTP Peers: 2
===============================================================================
The following command displays detailed PTP peers information and Output fields: PTP peers describes the output fields.
show system ptp peers detail ===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router : Base
IP Address : 1.4.1.21
Announce Direction: tx
Admin State : n/a G.8265.1 Priority : n/a
Local PTP Port : 3 PTP Port State : master
Clock Id : ac65fffffe000000 Remote PTP Port : 1
-------------------------------------------------------------------------------
Router : 1
IP Address : 1111:2222:3333:4444:5555:70:1:4
Announce Direction: rx+tx
Admin State : up G.8265.1 Priority : n/a
Local PTP Port : 2 PTP Port State : master
Clock Id : ac5efffffe000000 Remote PTP Port : 1
-------------------------------------------------------------------------------
Router : 1
IP Address : 1111:2222:3333:4444:5555:70:1:4
Announce Direction: rx
Admin State : up G.8265.1 Priority : n/a
Local PTP Port : 1 PTP Port State : slave
Clock Id : ac5dfffffe000000 Remote PTP Port : 1
GM Clock Id : ac5dfffffe000000 GM Clock Class : 13
GM Clock Accuracy : unknown GM Clock Variance : ffff (not computed)
GM Clock Priority1: 0 GM Clock Priority2 : 128
Steps Removed : 0 Parent Clock : yes
-------------------------------------------------------------------------------
Router : 2
IP Address : 1.1.1.21
Announce Direction: tx
Admin State : n/a G.8265.1 Priority : n/a
Local PTP Port : 4 PTP Port State : master
Clock Id : ac65fffffe000000 Remote PTP Port : 1
===============================================================================
The following command displays detailed PTP peers router information and Output fields: PTP peers describes the output fields.
show system ptp peers router detail===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router : 1
IP Address : 1.2.1.20
Announce Direction: rx+tx
Admin State : up G.8265.1 Priority : n/a
Local PTP Port : 2 PTP Port State : master
Clock Id : ac5efffffe000000 Remote PTP Port : 1
-------------------------------------------------------------------------------
Router : 1
IP Address : 1.3.1.19
Announce Direction: rx
Admin State : up G.8265.1 Priority : n/a
Local PTP Port : 1 PTP Port State : slave
Clock Id : ac5dfffffe000000 Remote PTP Port : 1
GM Clock Id : ac5dfffffe000000 GM Clock Class : 13
GM Clock Accuracy : unknown GM Clock Variance : ffff (not computed)
GM Clock Priority1: 0 GM Clock Priority2 : 128
Steps Removed : 0 Parent Clock : yes
===============================================================================
|
Label |
Description |
|---|---|
|
Router |
The name of the router instance |
|
IP Address |
The IP address of the PTP peer |
|
Announce Direction Anno Flow |
The direction from which PTP announce messages were sent or received |
|
Admin State |
The administrative state of the PTP peer |
|
G.8275 Priority |
The priority used in the best master clock algorithm (BMCA) for the local PTP port when the clock profile is G.8275.x |
|
Sync Interval |
The network synchronization interval, in packets per second |
|
Local PTP Port |
The number of local PTP ports |
|
PTP Port State |
The state of the PTP port |
|
Clock Id |
The clockIdentity value of the local PTP clock |
|
Remote PTP Port |
The number of remote PTP ports |
|
GM Clock Id |
The clockIdentity value of the grandmaster clock advertised by the parent clock |
|
GM Clock Class |
The clockClass value of the grandmaster clock advertised by the parent clock |
|
GM Clock Accuracy |
The clockAccuracy value of the grandmaster clock advertised by the parent clock |
|
GM Clock Variance |
The offsetScaledLogVariance value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority1 |
The priority1 value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority2 |
The priority2 value of the grandmaster clock advertised by the parent clock |
|
Steps Removed |
The number of steps removed the PTP peer is from a grandmaster clock |
|
Last Tx Port |
The port-id of the last port from which a synchronization packet was transmitted |
|
Last Rx Port |
The port-id of the last port into which a synchronization packet was received |
|
Port Asymmetry |
The asymmetry value of the PTP peer, in nanoseconds |
|
Best Master |
Whether the clock has been deemed to be the best master clock |
|
Parent Clock |
Whether there is an external parent clock |
|
APTS Asymmetry |
The APTS asymmetry value of the PTP peer, in nanoseconds |
|
Last Calc |
The date and time of the last asymmetry value calculation |
|
Profile Name |
The name of the alternate profile configuration. If an alternate profile is not configured, Primary is displayed as the profile name. |
|
Profile |
The PTP profile used for the alternate profile configuration.
|
|
Domain |
The domain in which PTP 1588 runs on the system. |
peers
Syntax
peers [detail]
Context
[Tree] (show>service>id>ptp peers)
Full Context
show service id ptp peers
Description
This command displays summary information for all the PTP peers.
Parameters
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following command displays PTP information for all peers.
show service id ptp peers=======================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router
IP Address
Anno Flow Admin State PTP Port State Parent Clock
-------------------------------------------------------------------------------
1
1.2.1.20
rx+tx up master no
1.3.1.19
rx up slave yes
-------------------------------------------------------------------------------
No. of PTP Peers: 4
===============================================================================
The following command displays detailed PTP information for all peers.
show service id ptp peers detail===============================================================================
IEEE 1588/PTP Peer Information
===============================================================================
Router : 1
IP Address : 1.2.1.20
Announce Direction: rx+tx
Admin State : up G.8265.1 Priority : n/a
Local PTP Port : 2 PTP Port State : master
Clock Id : ac5efffffe000000 Remote PTP Port : 1
-------------------------------------------------------------------------------
Router : 1
IP Address : 1.3.1.19
Announce Direction: rx
Admin State : up G.8265.1 Priority : n/a
Local PTP Port : 1 PTP Port State : slave
Clock Id : ac5dfffffe000000 Remote PTP Port : 1
GM Clock Id : ac5dfffffe000000 GM Clock Class : 13
GM Clock Accuracy : unknown GM Clock Variance : ffff (not computed)
GM Clock Priority1: 0 GM Clock Priority2 : 128
Steps Removed : 0 Parent Clock : yes
===============================================================================
| Label | Description |
|---|---|
|
Router |
The name of the router instance |
|
IP Address |
The IP address of the PTP peer |
|
Announce Direction Anno Flow |
The direction from which PTP announce messages were sent or received |
|
Admin State |
The administrative state of the PTP peer |
|
G.8265 Priority |
The priority used in the best master clock algorithm (BMCA) for the local PTP port when the clock profile is G.8265.x |
|
Sync Interval |
The network synchronization interval, in packets per second |
|
Alarms |
The alarms that are active for the PTP peer |
|
Tx Timestamp Point |
The transmission timestamp point |
|
Rx Timestamp Point |
The reception timestamp point |
|
Last Tx Port |
The port-id of the last port from which a synchronization packet was transmitted |
|
Last Rx Port |
The port-id of the last port into which a synchronization packet was received |
|
Port Asymmetry |
The asymmetry value of the PTP peer, in nanoseconds |
|
Best Master |
Whether the clock has been deemed to be the best master clock |
|
Parent Clock |
Whether there is an external parent clock |
|
Profile Name |
The name of the alternate profile configuration. If an alternate profile is not configured, Primary is displayed as the profile name. |
|
Profile |
The PTP profile used for the alternate profile configuration.
|
|
Domain |
The domain in which PTP 1588 runs on the system. |
peq
peq
Syntax
peq [peq-slot] [chassis chassis-id] [ detail]
Context
[Tree] (show peq)
Full Context
show peq
Description
This command displays APEQ information.
Parameters
- peq-slot
-
Specifies the APEQ slot identifier.
- chassis-id
-
Specifies the chassis ID for the router chassis.
- detail
-
Displays detailed information.
Platforms
7750 SR-12e, 7750 SR-s, 7950 XRS
Output
The following outputs are examples of PEQ information, and Output Fields: show peq describes the output fields.
Output Example: show peq*A:Dut-A# show peq
===============================================================================
PEQ Summary
===============================================================================
Chassis/ Provisioned Type Admin Operational Input Zone Input
Slot Equipped Type (if diff) State State A B Mode
-------------------------------------------------------------------------------
1/1 apeq-dc-2000 up down Y Y 1 N/A
1/2 (not provisioned) up unprovisioned Y Y 1 N/A
apeq-dc-2000
1/3 apeq-dc-2000 up up Y Y 1 N/A
1/4 apeq-dc-2000 up up Y Y 1 N/A
1/5 apeq-dc-2000 up up Y Y 1 N/A
1/6 apeq-dc-2000 up down Y Y 1 N/A
1/7 apeq-dc-2000 up down Y Y 1 N/A
1/8 apeq-dc-2000 up down Y Y 1 N/A
1/9 apeq-dc-2000 up down Y Y 1 N/A
1/10 apeq-dc-2000 up down Y Y 1 N/A
1/11 apeq-dc-2000 up down Y Y 1 N/A
1/12 apeq-dc-2000 up down Y Y 1 N/A
2/1 apeq-dc-2000 up provisioned - - 2 N/A
(not equipped)
===============================================================================
*A:Dut-A# show peq 1 detail
===============================================================================
PEQ 1
===============================================================================
Slot Provisioned Type Admin Operational Input Zone Input
Equipped Type (if diff) State State A B Mode
-------------------------------------------------------------------------------
1 apeq-dc-2000 down down Y N 1 N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0116
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number: 8205320107
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
===============================================================================
In the following example, the entries for PEQ 2 to PEQ 11 are not shown.
*A:Dut-A# show peq detail
===============================================================================
PEQ 1
===============================================================================
Slot Provisioned Type Admin Operational Input Zone Input
Equipped Type (if diff) State State A B Mode
-------------------------------------------------------------------------------
1/1 apeq-dc-2000 down down Y N 1 N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0116
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number: 8205320107
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
===============================================================================
...
===============================================================================
PEQ 12
===============================================================================
Slot Provisioned Type Admin Operational Input Zone Input
Equipped Type (if diff) State State A B Mode
-------------------------------------------------------------------------------
12 apeq-dc-2000 up up Y N 1 N/A
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0115
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number: 8205320107
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
===============================================================================
|
Label |
Description |
|---|---|
|
Slot |
The number of the slot in which the APEQ is installed. |
|
Provisioned Type Equipped Type (if different) |
The APEQ type provisioned. |
|
Admin State |
The administrative state. |
|
Operational State |
The operational state. |
|
Input |
Specifies the input battery feed: A, or B. |
|
Zone |
Specifies the chassis power zone. |
|
Hardware Data: |
|
|
Part number |
The APEQ part number. |
|
CLEI code |
The APEQ CLEI code. |
|
Serial number |
The APEQ serial number. |
|
Manufacture date |
The date the APEQ was manufactured. |
|
Manufacturing deviations |
Specifies any manufacturing deviations. |
|
Manufacturing assembly number |
The APEQ assembly number. |
|
Administrative state |
Specifies the administrative state of the APEQ. |
|
Operational state |
Specifies the operational state of the APEQ. |
|
Time of last boot |
Indicates the time stamp of the last system restart. |
|
Current alarm state |
Indicates the current alarm state. |
per-link-hash
per-link-hash
Syntax
per-link-hash [class {1 | 2 | 3}]
per-link-hash port port-id
Context
[Tree] (show>lag per-link-hash)
Full Context
show lag per-link-hash
Description
This command displays LAG per-link hash information.
Parameters
- port-id
-
Displays information about a specified LAG link-map profile.
Platforms
All
Output
The following output is an example of per-link hash SAP information.
Show Per-Link-Hash SAP Output Fields describes per-link hash SAP output fields.
Output Example
show lag 1 associations per-link-hash sap [class]
===============================================================================
SAP Associations
===============================================================================
SvcId SAP Active Link Oper
Class Weight
-------------------------------------------------------------------------------
10 lag-1:1 1/1/c1/1 1 111
10 lag-1:2 1/2/c1/1 2 222
10 lag-1:4 2/1/c1/4 2 333
10 lag-1:10 1/1/c1/1 3 444
10 lag-1:99 1/1/c1/1 2 1000
30 lag-1:31 1/1/c1/1 1 1
40 lag-1:41 1/2/c1/1 1 512
===============================================================================
Number of SAP associations: 7
===============================================================================|
Label |
Description |
|---|---|
|
SvcID |
The associated service ID |
|
SAP |
The associated LAG ID |
|
Active Link |
The associated SAP ID |
|
Oper Class |
The per-link-hash class |
|
Weight |
The per-link-hash weight |
|
Number of SAP associations |
The total number of SAPs associated with the specified LAG ID |
The following output is an example of per hash link Vport information.
Show Per-Link-Hash Vport Output Fields describes per hash link Vport output fields.
show lag 1 associations per-link-hash vport
===============================================================================
VPort Associations
===============================================================================
VPort Name Active Link
-------------------------------------------------------------------------------
my_vport_lag1 1/1/c1/1
my_vport_lag1bis 1/2/c1/1
my_vport_lag1_extra1 2/1/c1/4
my_vport_lag1_extra2 1/2/c1/1
my_vport_lag1_extra3 2/1/c1/4
===============================================================================
Number of VPort associations: 5
===============================================================================|
Label |
Description |
|---|---|
|
Vport Name |
The name of the virtual port |
|
Active Link |
The associated SAP ID |
|
Number of Vport associations |
The total number of Vports associated with the specified LAG ID |
The following output is an example of service subscriber host Vport information.
show service id subscriber-hosts detail
===============================================================================
Subscriber Host table
===============================================================================
Sap
IP Address
MAC Address PPPoE-SID Origin Fwding State
Subscriber
-------------------------------------------------------------------------------
lag-1:4
10.2.2.41
00:00:00:00:00:14 N/A DHCP Fwding
subscr2
-------------------------------------------------------------------------------
Subscriber-interface : subscr_lag1
Group-interface : group_lag1
Sub Profile : sub_profile
SLA Profile : sla_profile
Egress Vport : my_vport_lag1
LAG Active Link : 1/1/c1/1
-------------------------------------------------------------------------------|
Label |
Description |
|---|---|
|
Sap |
The LAG ID |
|
IP Address |
The subscriber host IP address |
|
MAC Address |
The subscriber host 48-bit MAC address |
|
Subscriber |
The associated subscriber profile name |
|
PPPoE-SID |
The PPPoE address of the segment identifier (SID) |
|
Origin |
The protocol or mechanism that created the service |
|
Fwding State |
The forwarding state |
|
Subscriber-interface |
The subscriber interface name associated with this service ID |
|
Group-interface |
The group interface name associated with this service ID |
|
Sub Profile |
The subscriber profile associated with this service ID |
|
SLA Profile |
The service level profile associated with this service ID |
|
Egress Vport |
The egress Vport name associated with this service ID |
|
LAG Active Link |
The associated SAP ID |
per-peer-queuing
per-peer-queuing
Syntax
per-peer-queuing [detail]
Context
[Tree] (show>system>security per-peer-queuing)
Full Context
show system security per-peer-queuing
Description
This command enables or disables CPM hardware queuing per peer. TTL security only operates when per-peer-queuing is enabled.
Platforms
All
Output
The following output is an example of per peer queuing information.
Show Per-Peer-Queuing Output Fields describes per-peer-queuing output fields.
Output ExampleA:ALA-48# show system security per-peer-queuing
=================================================
CPM Hardware Queuing
=================================================
Per Peer Queuing : Enabled
Total Num of Queues : 8192
Num of Queues In Use : 2
=================================================
A:ALA-48# configure
|
Label |
Description |
|---|---|
|
Per Peer Queuing |
Displays the status (enabled or disabled) of CPM hardware queuing per peer. |
|
Total Num of Queues |
Displays the total number of hardware queues. |
|
Num of Queues In Use |
Displays the total number of hardware queues in use. |
per-peer-queuing
Syntax
per-peer-queuing
Context
[Tree] (show>system>security per-peer-queuing)
Full Context
show system security per-peer-queuing
Description
This command displays the number of queues in use by the Qchip, which in turn is used by PPQ, CPM filter, SAP, and so on.
Platforms
All
Output
The following output is an example of per peer queuing information.
Show per-peer-queuing Output Fields describes the per-peer-queuing output fields.
Output ExampleA:ALA-48>show>system>security# per-peer-queuing
=================================================
CPM Hardware Queuing
=================================================
Per Peer Queuing : Enabled
Total Num of Queues : 8192
Num of Queues In Use : 0
=================================================
A:ALA-48>show>system>security#
|
Label |
Description |
|---|---|
|
Per Peer Queuing |
Displays whether per-peer-queuing is enabled or disabled. When enabled, a peering session is established and the router will automatically allocate a separate CPM hardware queue for that peer. When disabled, no hardware queuing per peer occurs. |
|
Total Num of Queues |
Displays the total number of CPM hardware queues. |
|
Num of Queues In Use |
Displays the number of CPM hardware queues that are in use. |
perform
perform
Syntax
perform
Context
[Tree] (tools perform)
Full Context
tools perform
Description
Commands in this context perform troubleshooting operations.
Platforms
All
performance
performance
Syntax
performance mda mda-id last time-span time-unit
Context
[Tree] (tools>dump>wlan-gw>isa performance)
Full Context
tools dump wlan-gw isa performance
Description
This command generates an overview of the processing load and data processed by the specified ISA over a period of time. The following time periods are supported:
-
last minute with seconds granularity
-
last hour with minutes granularity
-
last day with hours granularity
-
last day with days granularity
Parameters
- mda-id
-
Specifies the MDA for getting performance measurements in slot/mda format.
- time-span
-
Specifies the period for which to get measurements.
- time-unit
-
Specifies the period for which to get measurements.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s
Output
This command displays performance information.
Output ExampleNode# /tools dump wlan-gw isa performance mda 2/1 last 5 min
===============================================================================
Measurements for last 5 minutes on Slot #2 MDA #1
===============================================================================
Timestamp | Wait Idle Work | Total jobs | Total data
---------------------+----------------------------+------------+---------------
01/22/2018 10:14:04 | 99.47% 0.53% 0.00% | 0 | - -
01/22/2018 10:13:41 | 99.46% 0.54% 0.00% | 3 | 3 Kb
01/22/2018 10:12:41 | 99.47% 0.53% 0.00% | 0 | - -
01/22/2018 10:11:41 | 99.47% 0.53% 0.00% | 0 | - -
01/22/2018 10:10:41 | 99.45% 0.55% 0.00% | 0 | - -
===============================================================================
performance
Syntax
performance mda mda-id last time-span time-unit
Context
[Tree] (tools>dump>nat>isa performance)
Full Context
tools dump nat isa performance
Description
This command generates an overview of the processing load and data processed by the specified ISA over a period of time. The following time periods are supported:
-
last minute with seconds granularity
-
last hour with minutes granularity
-
last day with hours granularity
-
last 31 days with days granularity
Parameters
- mda-id
-
Specifies the MDA for getting performance measurements in format slot/mda.
- time-span
-
Specifies the period for which to get measurements.
- time-unit
-
Specifies the period for which to get measurements.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s
performance-monitoring
performance-monitoring
Syntax
performance-monitoring record record
Context
[Tree] (show>system>ptp performance-monitoring)
Full Context
show system ptp performance-monitoring
Description
This command displays the collected performance monitoring information for the PTP clock.
Parameters
- record
-
Specifies the time window for the record.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of PTP monitoring performance statistics and Output fields: PTP performance monitoring describes the output fields.
Output Exampleshow system ptp performance-monitoring record 503 ===============================================================================
IEEE 1588 Performance Monitoring Statistics
===============================================================================
-------------------------------------------------------------------------------
Record
-------------------------------------------------------------------------------
Index : 503
Valid : Yes
Start time : 2023/03/24 19:43:00 UTC
Complete : Yes
Duration : 1 minute
-------------------------------------------------------------------------------
Statistics
-------------------------------------------------------------------------------
offset-from-master
average : 0 ns
minimum : 0 ns
maximum : +1 ns
stddev : 0 ns
mean-path-delay
average : +10 ns
minimum : +10 ns
maximum : +11 ns
stddev : 0 ns
master-to-slave-delay
average : +10 ns
minimum : +10 ns
maximum : +11 ns
stddev : 0 ns
slave-to-master-delay
average : +10 ns
minimum : +10 ns
maximum : +11 ns
stddev : 0 ns
===============================================================================
|
Label |
Description |
|---|---|
|
IEEE 1588 Performance Monitoring Statistics |
|
|
Record |
|
|
Index |
The name of the router instance |
|
Valid |
The IP address of the PTP peer |
|
Start time |
The direction from which PTP announce messages were sent or received |
|
Complete |
The administrative state of the PTP peer |
|
Duration |
The priority used in the best master clock algorithm (BMCA) for the local PTP port when the clock profile is G.8265.x |
|
offset-from-master mean-path-delay master-to-slave-delay slave-to-master-delay |
Parameters from the time recovery algorithm as defined in the IEEE1588-2019 standard |
|
average minimum maximum stddev |
The average, minimum, maximum, and standard deviation of the values over the time interval of the record |
persistence
persistence
Syntax
persistence
Context
[Tree] (tools>perform persistence)
Full Context
tools perform persistence
Description
Commands in this context configure downgrade parameters.
Platforms
All
persistent
persistent
Syntax
persistent
Context
[Tree] (show>system>telemetry persistent)
Full Context
show system telemetry persistent
Description
Commands in this context display persistent telemetry information.
Platforms
All
pfcp
pfcp
Syntax
pfcp
Context
[Tree] (show>subscr-mgmt pfcp)
Full Context
show subscriber-mgmt pfcp
Description
Commands in this context display all related PFCP information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pfcp-association
pfcp-association
Syntax
pfcp-association name statistics
Context
[Tree] (clear>subscr-mgmt pfcp-association)
Full Context
clear subscriber-mgmt pfcp-association
Description
This command clears all message statistics associated with the specified PFCP association.
Parameters
- name
-
Specifies the name of a PFCP association, up to 32 characters, for which information is cleared.
- statistics
-
Specifies that statistics for the specified PFCP association are cleared.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pfcp-session
pfcp-session
Syntax
pfcp-session session-id session-id
pfcp-session sap sap-id mac mac-address
Context
[Tree] (clear>subscr-mgmt pfcp-session)
Full Context
clear subscriber-mgmt pfcp-session
Description
This command locally clears a PFCP session, either by providing the session ID or the associated SAP ID and MAC address.
This command does not delete the session on the BNG CPF and should only be used as a last attempt to delete the PFCP sessions. It is always recommended to first attempt to gracefully delete the session from the BNG CPF.
Parameters
- session-id
-
Specifies the locally assigned PFCP session ID, up to 20 characters.
- sap-id
-
Specifies the SAP ID associated with the session.
- mac-address
-
Specifies the MAC address associated with the session, in the form xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pim
pim
Syntax
pim
Context
[Tree] (clear>router pim)
Full Context
clear router pim
Description
Commands in this context clear and reset PIM entities.
Platforms
All
pim
Syntax
pim
Context
[Tree] (show>router pim)
Full Context
show router pim
Description
Commands in this context display PIM related information.
Platforms
All
pim
Syntax
pim
Context
[Tree] (tools>perform>router pim)
Full Context
tools perform router pim
Description
This command enables tools to perform certain PIM tasks.
Platforms
All
pim
Syntax
pim
Context
[Tree] (monitor>router pim)
Full Context
monitor router pim
Description
This command monitors commands for the PIM instance.
Platforms
All
pim-policy
pim-policy
Syntax
pim-policy
pim-policy name associations
Context
[Tree] (show>subscr-mgmt pim-policy)
Full Context
show subscriber-mgmt pim-policy
Description
This command displays PIM policy information.
Parameters
- name
-
Specifies the PIM policy name, up to 32 characters.
- associations
-
Displays information associated with the policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pim-snooping
pim-snooping
Syntax
pim-snooping
Context
[Tree] (show>service>id pim-snooping)
Full Context
show service id pim-snooping
Description
Commands in this context display PIM snooping information.
Platforms
All
pim-snooping
Syntax
pim-snooping
Context
[Tree] (clear>service>id pim-snooping)
Full Context
clear service id pim-snooping
Description
Commands in this context clear PIM snooping information.
Platforms
All
ping-template
ping-template
Syntax
ping-template template-name
ping-template
Context
[Tree] (show>test-oam>icmp ping-template)
Full Context
show test-oam icmp ping-template
Description
This command displays a summary of configured ping templates and the total number service interfaces that reference the template. By specifying template name, the values for the specified interface and the total and active references for that specific template are displayed.
Parameters
- template-name
-
Specifies the name of the ping template to be queried, up to 64 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of ping template information.
Output Exampleshow test-oam icmp ping-template
===============================================================================
Ping Templates
===============================================================================
Name IP Refs
-------------------------------------------------------------------------------
base-template 21
-------------------------------------------------------------------------------
No. of ping templates: 1
===============================================================================
show test-oam icmp ping-template base-template
======================================================================
Tmpl Name : base-template
======================================================================
Description : Basic standard template
Dscp : nc1
Dot1p : 7
Interval : 60
Timeout : 5
Failure Threshold : 3
React Interval : 1
React Fail Thresh : 3
React Timeout : 1
React Threshold : 3
Size : 56
TTL : 1
----------------------------------------------------------------------
Active Refs : 20
Total Refs : 21
======================================================================
ping-template-sync
ping-template-sync
Syntax
ping-template-sync template-name
Context
[Tree] (tools>perform>test-oam>icmp ping-template-sync)
Full Context
tools perform test-oam icmp ping-template-sync
Description
This command updates all values for service IP interfaces that reference the specified config>test-oam>icmp>ping-template template-name. Changes to the ping-template in this context are not automatically pushed to service IP interfaces. Values imported by the service interface are those configured when the service IP interface referenced the ping- template.
Parameters
- template-name
-
Specifies the ping template name, up to 64 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
ping-template-using
ping-template-using
Syntax
ping-template-using [template-name]
Context
[Tree] (show>test-oam>icmp ping-template-using)
Full Context
show test-oam icmp ping-template-using
Description
This command displays information about service IP interfaces that reference a ping template, the associated router instance, and the administrative state of the ping template under that interface.
Parameters
- template-name
-
Displays the interfaces mapped to the ping-template template-name, up to 64 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example ping template output information.
Output Exampleshow test-oam icmp ping-template-using
===============================================================================
Ping Templates
===============================================================================
Template Name Router Instance Admin
Interface Name
-------------------------------------------------------------------------------
base-template
int-PE-2-CE-101 vprn12101 up
base-template
int-PE-2-CE-103 vprn12103 up
base-template
int-PE-2-CE-104 vprn12104 up
base-template
int-PE-2-CE-105 vprn12105 up
base-template
int-PE-2-CE-106 vprn12106 up
base-template
int-PE-2-CE-107 vprn12107 up
base-template
int-PE-2-CE-108 vprn12108 up
base-template
int-PE-2-CE-109 vprn12109 up
base-template
int-PE-2-CE-110 vprn12110 up
base-template
int-PE-2-CE-111 vprn12111 up
base-template
int-PE-2-CE-112 vprn12112 up
base-template
int-PE-2-CE-113 vprn12113 up
base-template
int-PE-2-CE-114 vprn12114 up
base-template
int-PE-2-CE-115 vprn12115 up
base-template
int-PE-2-CE-116 vprn12116 up
base-template
int-PE-2-CE-117 vprn12117 up
base-template
int-PE-2-CE-118 vprn12118 up
base-template
int-PE-2-CE-119 vprn12119 up
base-template
int-PE-2-CE-120 vprn12120 up
base-template
int-PE-2-CE-121 vprn12121 down
base-template
int-PE-2-CE-122 vprn12122 up
===============================================================================
Show test-oam icmp ping-template-using Output Fields describes ping template fields.
| Label | Description |
|---|---|
|
Template Name |
The template name |
|
Router Instance |
The router instance name |
|
Admin |
The administrative state |
|
Interface Name |
The interface name |
pip
pip
Syntax
pip
Context
[Tree] (clear>service>statistics>id pip)
Full Context
clear service statistics id pip
Description
This command clears the Provider Internal Port statistics for this service.
Platforms
All
policer
policer
Syntax
policer
policer policer-name [detail]
policer summary
Context
[Tree] (show>app-assure>group policer)
Full Context
show application-assurance group policer
Description
This command displays application-assurance policer information.
Parameters
- policer-name
-
Displays information about the specified policer.
- detail
-
Displays detailed information about policers on this node.
- summary
-
Displays summarized information about policers on this node.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the policer command information.
Output Exampleshow application-assurance group 1 policer <policer-name> detail
===============================================================================
Policer Instance "1m-dwn"
===============================================================================
Description : (Not Specified)
Type : dual-bucket-bandwidth
Granularity : subscriber
Adaptation Rule : pir closest cir closest
Active tod-override : none
PIR : max Oper PIR : max
CIR : 0 kbps Oper CIR : 0 kbps
MBS : 20000 KB Oper MBS : 20000 KB
CBS : 0 KB Oper CBS : 0 KB
No. of tod-overrides : 2
-------------------------------------------------------------------------------
Time of Day Override Instance 10
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : in-service
Occurrence : daily (monday tuesday wednesday thursday friday)
Start time : 19:00
End time : 22:00
PIR : max
CIR : 0 kbps
MBS : 10000 KB
CBS : 0 KB
-------------------------------------------------------------------------------
Time of Day Override Instance 20
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : in-service
Occurrence : daily (sunday saturday)
Start time : 19:00
End time : 22:00
PIR : max
CIR : 0 kbps
MBS : 5000 KB
CBS : 0 KB
===============================================================================
*A:Dut-C>show>app-assure>group# policer "test"
===============================================================================
Policer Instance "test"
===============================================================================
Description : (Not Specified)
Type : single-bucket-bandwidth
Granularity : access-network-location
Action : permitDeny
Adaptation Rule : pir closest
Rate-Percentage : 10
===============================================================================
policer
Syntax
policer policer-name day day time time-of-day
Context
[Tree] (tools>dump>app-assure>group policer)
Full Context
tools dump application-assurance group policer
Description
This command displays rates for the policer for a specific day and time.
Parameters
- policer-name
-
Specifies an existing policer name up to 256 characters in length.
- day day
-
Specifies a day to display policer rates.
- time time-of-day
-
Specifies a time of day (in hours and minutes) to display policer rates.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
policer
Syntax
policer
Context
[Tree] (show>qos policer)
Full Context
show qos policer
Description
Commands in this context display QoS policer information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
policer-control-policy
policer-control-policy
Syntax
policer-control-policy [policy-name] [association]
Context
[Tree] (show>qos policer-control-policy)
Full Context
show qos policer-control-policy
Description
This command displays policer control policy information.
Parameters
- policy-name
-
Specifies the policer control policy name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
policer-hierarchy
policer-hierarchy
Syntax
policer-hierarchy
Context
[Tree] (show>qos policer-hierarchy)
Full Context
show qos policer-hierarchy
Description
This command displays policer hierarchy information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
policers
policers
Syntax
policers
Context
[Tree] (show>app-assure>group>aa-sub policers)
Full Context
show application-assurance group aa-sub policers
Description
This command displays policer configuration information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the policers command.
Output ExampleA:cpm-a>show>app-assure>group>aa-sub# policers
===============================================================================
Application-Assurance Subscriber Policer Summary
===============================================================================
AA-Subscriber : Alex (esm)
-------------------------------------------------------------------------------
Type: single-bucket-bandwidth Direction: subscriber-to-network
-------------------------------------------------------------------------------
AQP Policer Resources Exceeded?
-------------------------------------------------------------------------------
61 SuspectUp_policer N
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Type: single-bucket-bandwidth Direction: network-to-subscriber
-------------------------------------------------------------------------------
AQP Policer Resources Exceeded?
-------------------------------------------------------------------------------
62 SuspectDown_policer N
-------------------------------------------------------------------------------
Policer usage counts:
single-bucket-bandwidth
subscriber-to-network 1 out of 32
network-to-subscriber 1 out of 32
dual-bucket-bandwidth
subscriber-to-network 0 out of 1
network-to-subscriber 0 out of 1
flow-count-limit 0 out of 8
flow-rate-limit 0 out of 8
===============================================================================
A:cpm-a>show>app-assure>group>aa-sub#
policy
policy
Syntax
policy
Context
[Tree] (show>app-assure>group policy)
Full Context
show application-assurance group policy
Description
Commands in this context display application-assurance policy configuration information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
policy
Syntax
policy [policy-name [bundle bundle-name] [ protocol protocol-name] [interface if-name] [ detail]]
Context
[Tree] (show>router>mcac policy)
Full Context
show router mcac policy
Description
This command displays MCAC policy information.
Parameters
- policy-name
-
Specifies an existing multicast CAC (MCAC) policy name.
- bundle bundle-id
-
Specifies an existing multicast bundle name.
- protocol protocol-name
-
specifies an applicable protocol to display.
- interface if-name
-
Specifies an interface name to display.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of MCAC policy information.
Output Example*A:ALA-48>show>router>mcac# policy
===============================================================================
Multicast CAC Policies
===============================================================================
Policy Description
-------------------------------------------------------------------------------
btv_fr foreign TV offering
btv_vl eastern TV offering
policy1 this is policy1
policy2 this is policy 2
-------------------------------------------------------------------------------
Policies : 4
===============================================================================
*A:ALA-48>show>router>mcac#
*A:ALA-48>show>router>mcac# policy btv_fr
===============================================================================
Multicast CAC policy
===============================================================================
Policy : btv_fr
Description : foreign TV offering
Default Action : discard
Bundle(s) : FOR
===============================================================================
*A:ALA-48>show>router>mcac#
policy
Syntax
policy admin
policy as-path-group [asp-group-name]
policy as-path [asp-name]
policy community [community-name]
policy damping [damping-profile-name]
policy exclusive-access
policy global-variables
policy [plcy-name] [expand-variables]
policy prefix-list [prefix-list-name]
policy route-distinguisher-list [rd-list-name]
policy plcy-name sub-policy entry entry-id [name subpol-name]
policy plcy-name sub-policy entry entry-id name subpol-name entry-2 entry-id name-2 subpol-name
policy plcy-name sub-policy entry entry-id name subpol-name entry-2 entry-id name-2 subpol-name entry-3 entry-id name-3 subpol-name
Context
[Tree] (show>router policy)
Full Context
show router policy
Description
This command displays configured policy statement information.
Parameters
- admin
-
When this keyword is specified, the entire policy option configuration is displayed, including any uncommitted configuration changes. This command is similar to the info command.
Note:This parameter is not available in the MD-CLI.
- as-path
-
When this keyword is specified, the parameter displays configured as-path regular expressions (optionally filtered by name).
- as-path-group
-
When this keyword is specified, the command displays configured as-path-groups, optionally filtered by name.
- community
-
When this keyword is specified, the command displays configured community lists, optionally filtered by name.
- damping
-
When this keyword is specified, the information about the route policy damping configurations is displayed.
- entry entry-id
-
Displays the configuration (with parameter value substitution) of the subroutine policy called by the entry with entry ID.
- exclusive-access
-
Displays the policy that edits exclusive access and lock information.
Note:This parameter is not available in the MD-CLI.
- expand-variables
-
Displays the variables that are replaced with values in main policies or in sub-policies.
- prefix-list name
-
Displays the prefix lists configured in the route policy.
- policy name
-
Displays information similar to the info command for a specific policy-statement. If a name is provided, the matching policy-statement displays. If no statement name is specified, a list of all policies statements and descriptions display.
- route-distinguisher rd-list-name
- Keyword to display all the configured route distinguisher lists. If an rd-list-name is provided, the specified route distinguisher list is displayed.
- sub-policy
-
When this keyword is specified, the configuration of a subroutine policy is displayed.
- subpol-name
-
Specifies the policy name up to 64 characters.
- entry-id
-
Specifies the numeric entry identifier of the policy.
Platforms
All
Output
Route Policy Output Fields describes route policy output fields.
Use the following command to display all configured route policies.
show router policy===============================================================================
Route Policies
===============================================================================
Policy Description
-------------------------------------------------------------------------------
Direct And Aggregate Policy Statement ABC
-------------------------------------------------------------------------------
Policies :
===============================================================================Use the following command to display the entire policy option configuration, including any uncommitted configuration changes.
show router policy adminprefix-list "All-Routes"
prefix 0.0.0.0/0 longer
prefix 2.0.0.0/8 longer
prefix 3.0.0.0/8 longer
prefix 4.0.0.0/8 longer
prefix 5.0.0.0/8 longer
prefix 6.0.0.0/8 exact
prefix 224.0.0.0/24 longer
exit
...Use the following command to display information about a specific route policy.
show router policy namedescription "Policy Statement For 'BGP To RIP'"
entry 10
description "Entry For Policy 'BGP To RIP'"
from
protocol bgp
exit
to
protocol rip
exit
action accept
metric set 1
next-hop 10.0.18.200
tag 805
exit
exit
default-action rejectUse the following command to display information about the route policy damping configurations.
show router policy damping=============================================
Route Damping Profiles
=============================================
damping "TEST-LOW"
half-life 22
max-suppress 720
reuse 10000
suppress 15000
exit
damping "TEST-HIGH"
half-life 22
max-suppress 720
reuse 1000
suppress 5000
exit
damping "TEST-MEDIUM"
half-life 22
max-suppress 720
reuse 5000
suppress 11000
exit
=============================================Use the following command to display information about the subroutine called by an entry of the route policy.
show router policy "poll" sub-policy entry 10 name "pol2"===============================================================================
pol1 entry 10 sub-policies
===============================================================================
-------------------------------------------------------------------------------
Level1 Sub-policy : pol2 Parent-policy : pol1, Parent-entry 10
-------------------------------------------------------------------------------
entry 20
from
community "telnet"
exit
exit
===============================================================================|
Label |
Description |
|---|---|
|
Policy |
Displays a list of route policy names. |
|
Description |
Displays the description of each route policy. |
|
Policies |
The total number of policies configured. |
policy
Syntax
policy [policy-id [event event-type specific-qualifier]]
Context
[Tree] (show>vrrp policy)
Full Context
show vrrp policy
Description
This command displays VRRP priority control policy information.
If no command line options are specified, a summary of the VRRP priority control event policies displays.
Parameters
- policy-id
-
Displays information on the specified priority control policy ID.
- event-type
-
Displays information on the specified VRRP priority control event within the policy ID.
- specific-qualifier
-
Display information about the specified qualifier.
Platforms
All
Output
VRRP Policy Output — The following output is an example of VRRP policy information, and Show VRRP Policy Output Fields describes the fields.
|
Label |
Description |
|---|---|
|
Policy Id |
The VRRP priority control policy associated with the VRRP virtual router instance A value of 0 indicates that no control policy is associated with the virtual router instance |
|
Current Priority & Effects |
|
|
Current Explicit |
When multiple explicitly defined events associated with the priority control policy happen simultaneously, the lowest value of all the current explicit priorities will be used as the in-use priority for the virtual router |
|
Current Delta Sum |
The sum of the priorities of all the delta events when multiple delta events associated with the priority control policy happen simultaneously; this sum is subtracted from the base priority of the virtual router to give the in-use priority |
|
Delta Limit |
The delta-in-use-limit for a VRRP policy; once the total sum of all delta events has been calculated and subtracted from the base-priority of the virtual router, the result is compared to the delta-in-use-limit value; if the result is less than this value, the delta-in-use-limit value is used as the virtual router in-use priority value; if an explicit priority control event overrides the delta priority control events, the delta-in-use-limit has no effect If the delta-in-use-limit is 0, the sum of the delta priority control events to reduce the virtual router's in-use-priority to 0 can prevent it from becoming or staying master |
|
Current Priority |
The configured delta-in-use-limit priority for a VRRP priority control policy or the configured delta or explicit priority for a priority control event |
|
Applied |
The number of virtual router instances to which the policy has been applied; the policy cannot be deleted unless this value is 0 |
|
Description |
A text string which describes the VRRP policy |
|
Event Type & ID |
A delta priority event is a conditional event defined in a priority control policy that subtracts a given amount from the base priority to give the current in-use priority for the VRRP virtual router instances to which the policy is applied An explicit priority event is a conditional event defined in a priority control policy that explicitly defines the in-use priority for the VRRP virtual router instances to which the policy is applied Explicit events override all delta events; when multiple explicit events occur simultaneously, the event with the lowest priority value defines the in-use priority |
|
Event Oper State |
The operational state of the event |
|
Hold Set Remaining |
The amount of time that must pass before the set state for a VRRP priority control event can transition to the cleared state to dampen flapping events |
|
Priority & Effect |
Delta — the priority-level value is subtracted from the associated virtual router instance’s base priority when the event is set and no explicit events are set; the sum of the priority event priority-level values on all set delta priority events are subtracted from the virtual router base priority to derive the virtual router instance in-use priority value If the delta priority event is cleared, the priority-level is no longer used in the in-use priority calculation |
|
Explicit — the priority-level value is used to override the base priority of the virtual router instance if the priority event is set and no other explicit priority event is set with a lower priority-level The set explicit priority value with the lowest priority-level determines the actual in-use protocol value for all virtual router instances associated with the policy |
|
|
In Use |
Specifies whether the event is currently affecting the in-use priority of some virtual router |
A:ALA-A# show vrrp policy
===============================================================================
VRRP Policies
===============================================================================
Policy Current Current Current Delta Applied
Id Priority & Effect Explicit Delta Sum Limit
-------------------------------------------------------------------------------
1 None None None 1 Yes
2 None None None 1 No
===============================================================================
A:ALA-A#
A:ALA-A# show vrrp policy 1
===============================================================================
VRRP Policy 1
===============================================================================
Description : 10.10.200.253 reachability
Current Priority: None Applied : No
Current Explicit: None Current Delta Sum : None
Delta Limit : 1
-------------------------------------------------------------------------------
Applied To VR Opr Base In-use Master Is
Interface Name Id Pri Pri Pri Master
-------------------------------------------------------------------------------
None
-------------------------------------------------------------------------------
Priority Control Events
-------------------------------------------------------------------------------
Event Type & ID Event Oper State Hold Set Priority In
Remaining &Effect Use
-------------------------------------------------------------------------------
Host Unreach 10.10.200.252 n/a Expired 20 Del No
Host Unreach 10.10.200.253 n/a Expired 10 Del No
Route Unknown 10.10.100.0/24 n/a Expired 1 Exp No
===============================================================================
VRRP Policy Event Output — The following output is an example of VRRP policy event information, and Show VRRP Policy Event Output Fields describes the fields.
Output ExampleA:ALA-A#show vrrp policy 1 event port-down
===============================================================================
VRRP Policy 1, Event Port Down 1/1/1
===============================================================================
Description :
Current Priority: None Applied : Yes
Current Explicit: None Current Delta Sum : None
Delta Limit : 1
-------------------------------------------------------------------------------
Applied To VR Opr Base In-use Master Is
Interface Name Id Pri Pri Pri Master
-------------------------------------------------------------------------------
ies301backup 1 Down 100 100 0 No
-------------------------------------------------------------------------------
Priority Control Event Port Down 1/1/1
-------------------------------------------------------------------------------
Priority : 30 Priority Effect : Delta
Hold Set Config : 0 sec Hold Set Remaining: Expired
Value In Use : No Current State : Cleared
# trans to Set : 6 Previous State : Set-down
Last Transition : 04/13/2007 04:54:35
===============================================================================
A:ALA-A#
A:ALA-A# show vrrp policy 1 event host-unreachable
===============================================================================
VRRP Policy 1, Event Host Unreachable 10.10.200.252
===============================================================================
Description : 10.10.200.253 reachability
Current Priority: None Applied : No
Current Explicit: None Current Delta Sum : None
Delta Limit : 1
-------------------------------------------------------------------------------
Applied To VR Opr Base In-use Master Is
Interface Name Id Pri Pri Pri Master
-------------------------------------------------------------------------------
None
-------------------------------------------------------------------------------
Priority Control Event Host Unreachable 10.10.200.252
-------------------------------------------------------------------------------
Priority : 20 Priority Effect : Delta
Interval : 1 sec Timeout : 1 sec
Drop Count : 3
Hold Set Config : 0 sec Hold Set Remaining: Expired
Value In Use : No Current State : n/a
# trans to Set : 0 Previous State : n/a
Last Transition : 04/13/2007 23:10:24
===============================================================================
A:ALA-A#
A:ALA-A# show vrrp policy 1 event route-unknown
===============================================================================
VRRP Policy 1, Event Route Unknown 10.10.100.0/24
===============================================================================
Description : 10.10.200.253 reachability
Current Priority: None Applied : No
Current Explicit: None Current Delta Sum : None
Delta Limit : 1
-------------------------------------------------------------------------------
Applied To VR Opr Base In-use Master Is
Interface Name Id Pri Pri Pri Master
-------------------------------------------------------------------------------
None
-------------------------------------------------------------------------------
Priority Control Event Route Unknown 10.10.100.0/24
-------------------------------------------------------------------------------
Priority : 1 Priority Effect : Explicit
Less Specific : No Default Allowed : No
Next Hop(s) : None
Protocol(s) : None
Hold Set Config : 0 sec Hold Set Remaining: Expired
Value In Use : No Current State : n/a
# trans to Set : 0 Previous State : n/a
Last Transition : 04/13/2007 23:10:24
===============================================================================
|
Label |
Description |
|---|---|
|
Description |
A text string which describes the VRRP policy |
|
Policy Id |
The VRRP priority control policy associated with the VRRP virtual router instance A value of 0 indicates that no control policy is associated with the virtual router instance |
|
Current Priority |
The base router priority for the virtual router instance used in the master election process |
|
Current Explicit |
When multiple explicitly defined events associated with the priority control policy happen simultaneously, the lowest value of all the current explicit priorities will be used as the in-use priority for the virtual router |
|
Applied |
The number of virtual router instances to which the policy has been applied; the policy cannot be deleted unless this value is 0 |
|
Current Delta Sum |
The sum of the priorities of all the delta events when multiple delta events associated with the priority control policy happen simultaneously; this sum is subtracted from the base priority of the virtual router to give the in-use priority |
|
Delta Limit |
The delta-in-use-limit for a VRRP policy; once the total sum of all delta events has been calculated and subtracted from the base-priority of the virtual router, the result is compared to the delta-in-use-limit value; if the result is less than this value, the delta-in-use-limit value is used as the virtual router in-use priority value; if an explicit priority control event overrides the delta priority control events, the delta-in-use-limit has no effect If the delta-in-use-limit is 0, the sum of the delta priority control events to reduce the virtual router's in-use-priority to 0 can prevent it from becoming or staying master |
|
Applied to Interface Name |
The interface name where the VRRP policy is applied |
|
VR ID |
The virtual router ID for the IP interface |
|
Opr |
Up — indicates that the operational state of the VRRP instance is up |
|
Down — indicates that the operational state of the VRRP instance is down |
|
|
Base Pri |
The base priority used by the virtual router instance |
|
InUse Priority |
The current in-use priority associated with the VRRP virtual router instance |
|
Master Priority |
The priority of the virtual router instance which is the current master |
|
Priority |
The base priority used by the virtual router instance |
|
Priority Effect |
Delta — a delta priority event is a conditional event defined in a priority control policy that subtracts a given amount from the base priority to give the current in-use priority for the VRRP virtual router instances to which the policy is applied |
|
Explicit — a conditional event defined in a priority control policy that explicitly defines the in-use priority for the VRRP virtual router instances to which the policy is applied Explicit events override all delta events; when multiple explicit events occur simultaneously, the event with the lowest priority value defines the in-use priority |
|
|
Current Priority |
The configured delta-in-use-limit priority for a VRRP priority control policy or the configured delta or explicit priority for a priority control event |
|
Event Oper State |
The operational state of the event |
|
Hold Set Remaining |
The amount of time that must pass before the set state for a VRRP priority control event can transition to the cleared state to dampen flapping events |
|
Priority |
The base priority used by the virtual router instance |
|
Priority Effect |
Delta — the priority-level value is subtracted from the associated virtual router instance’s base priority when the event is set and no explicit events are set; the sum of the priority event priority-level values on all set delta priority events are subtracted from the virtual router base priority to derive the virtual router instance in-use priority value If the delta priority event is cleared, the priority-level is no longer used in the in-use priority calculation |
|
Explicit — the priority-level value is used to override the base priority of the virtual router instance if the priority event is set and no other explicit priority event is set with a lower priority-level The set explicit priority value with the lowest priority-level determines the actual in-use protocol value for all virtual router instances associated with the policy |
|
|
Hold Set Config |
The configured number of seconds that the hold-set timer waits after an event enters a set state or enters a higher threshold set state, depending on the event type |
|
Value In Use |
Yes — the event is currently affecting the in-use priority of some virtual router |
|
No — the event is not affecting the in-use priority of some virtual router |
|
|
# trans to Set |
The number of times the event has transitioned to one of the 'set' states |
|
Last Transition |
The time and date when the operational state of the event last changed |
policy
Syntax
policy [policy-id] association
Context
[Tree] (show>system>security>dist-cpu-protection policy)
[Tree] (show>system>security>cpu-protection policy)
Full Context
show system security dist-cpu-protection policy
show system security cpu-protection policy
Description
This command displays CPU protection policy information.
Parameters
- policy-id
-
Displays CPU protection policy information for the specified policy ID.
- association
-
This keyword displays associations for the specified policy ID.
Platforms
All
- show system security dist-cpu-protection policy
7450 ESS, 7750 SR-7/12/12e, 7750 SR-7s, 7750 SR-14s, 7950 XRS
- show system security cpu-protection policy
policy
Syntax
policy policy-assoc-name
Context
[Tree] (show>router>pcep>pcc>pce-assoc policy)
Full Context
show router pcep pcc pce-associations policy
Description
This command displays the policy association information.
If a policy association name is not specified, the information for all configured policy associations is displayed.
Parameters
- policy-assoc-name
-
Specifies the name of the policy association, up to 32 characters.
Platforms
All
Output
The following output is an example of policy association information, and Show Policy Association Descriptions describes the output fields.
Output Example*A:Dut-C>config>router>mpls>lsp# show router pcep pcc pce-associations policy "test_pol"
===============================================================================
PCEP PCC Policy Associations Info
===============================================================================
Assocation Name : test_pol
Association ID : 10 Association Source : 192.168.213.59
===============================================================================
|
Label |
Description |
|---|---|
|
Association Name |
The policy association name |
|
Association ID |
The policy association ID |
|
Association Source |
The source IP address of the policy association. Both IPv4 and IPv6 are supported. |
policy-edits
policy-edits
Syntax
policy-edits
Context
[Tree] (show>router policy-edits)
Full Context
show router policy-edits
Description
This command displays edited policy information that was entered in the classic CLI.
This command is not available in the MD-CLI.
Platforms
All
policy-test
policy-test
Syntax
policy-test plcy-or-long-expr [ plcy-or-expr [plcy-or-expr...{up tp 14 max}] [family family] [rd rd] prefix ip-prefix/ip-prefix-length [ longer] [neighbor ip-address] [display-rejects] [{detail | brief}] [display-rejects-only] [export] [ protocol protocol]
Context
[Tree] (show>router>bgp policy-test)
Full Context
show router bgp policy-test
Description
This command allows the operator to evaluate existing route policy or chain of route policies or route policy logical expression effects, as a BGP import or export policy, by identifying the routes that would be accepted or rejected after the complete evaluation.
When the policy, list of policies or logical expression is used as a BGP export policy, the export keyword must be included. When the policy is used as a BGP import policy, the export keyword should not be included.
Parameters
- plcy-or-long-expr
-
Specifies up to 14 policy names or a long expression.
- plcy-or-expr
-
Specifies the policy name or expression.
- family
-
ipv4, ipv6, vpn-ipv4, vpn-ipv6, label-ipv4, label-ipv6.
- rd
-
Specifies the route distinguisher value in one of the following formats:
-
ip-addr:comm-val
-
2byte-asnumber:ext-comm-val
-
4byte-asnumber:comm-val
-
- ip-prefix/ip-prefix-length
-
Specifies an IPv4 or IPv6 prefix/mask to be evaluated. The keyword longer may be specified to evaluate longer prefix matches (optional).
- ip-address
-
Specifies the IPv4 or IPv6 address of a peer from which the BGP routes to be evaluated were sent, up to 64 characters.
- longer
-
Matches prefixes with a longer prefix-length.
- display-rejects
-
Displays routes that were rejected by the policy. If not specified, only a count of rejected routes are shown.
- detail
-
When the policy modifies route attributes, it displays the modifications made to the routes. This command requires an exact prefix to be specified.
- brief
-
Provides a summarized display of the route attributes modifications. This command requires an exact prefix to be specified.
- display-rejects-only
-
Displays only routes rejected by the policy test.
- export
-
Indicates that the policy test is conducted in the context of a BGP export policy. The analyzed set of routes also include non-BGP routes that can be redistributed by BGP.
- protocol
-
Displays routes by the protocol type. This keyword is only applicable when the export keyword is also present.
Platforms
All
Output
The following output is an example of policy test information, and Show Policy Test Field Descriptions describes the output fields.
Output ExampleA:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 0.0.0.0/0
longer neighbor 220.0.0.2
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network LocalPref MED
Nexthop Path-Id VPNLabel
As-Path
-------------------------------------------------------------------------------
Accepted by Policy
u*>? 4.0.0.6/32 None None
220.0.0.2 None -
14
-------------------------------------------------------------------------------
Total Routes : 17 Routes rejected : 16
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 prefix 0.0.0.0/0 longer neighbor
220.0.0.2
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network
-------------------------------------------------------------------------------
Accepted by Policy
u*>? 4.0.0.6/32
-------------------------------------------------------------------------------
Total Routes : 17 Routes rejected : 16
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 0.0.0.0/0
longer neighbor 220.0.0.2 display-rejects brief
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network
-------------------------------------------------------------------------------
Rejected by Default action
u*>? 2.2.2.2/32
Rejected by Default action
u*>? 4.0.0.1/32
Rejected by Default action
u*>? 4.0.0.2/32
Rejected by Default action
u*>? 4.0.0.3/32
Rejected by Default action
u*>? 4.0.0.4/32
Rejected by Default action
u*>? 4.0.0.5/32
Accepted by Policy
u*>? 4.0.0.6/32
Rejected by Default action
u*>? 6.0.0.1/32
Rejected by Default action
u*>? 7.0.0.1/32
Rejected by Default action
u*>i 10.0.4.0/24
Rejected by Default action
*i 10.12.0.0/24
Rejected by Default action
*i 10.14.0.0/24
Rejected by Default action
u*>i 10.24.0.0/24
Rejected by Default action
*i 12.12.12.12/32
Rejected by Default action
*i 220.0.0.2/32
Rejected by Default action
*i 220.0.0.3/32
Rejected by Default action
u*>i 221.0.0.2/32
-------------------------------------------------------------------------------
Total Routes : 17 Routes rejected : 16
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 prefix 0.0.0.0/0 longer neighbor
220.0.0.2 display-rejects
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network LocalPref MED
Nexthop Path-Id VPNLabel
As-Path
-------------------------------------------------------------------------------
Rejected by Default action
u*>? 2.2.2.2/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.1/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.2/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.3/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.4/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.5/32 None None
220.0.0.2 None -
14
Accepted by Policy
u*>? 4.0.0.6/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 6.0.0.1/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 7.0.0.1/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>i 10.0.4.0/24 None None
220.0.0.2 None -
14
Rejected by Default action
*i 10.12.0.0/24 None 20
220.0.0.2 None -
14
Rejected by Default action
*i 10.14.0.0/24 None None
220.0.0.2 None -
14
Rejected by Default action
u*>i 10.24.0.0/24 None None
220.0.0.2 None -
14
Rejected by Default action
*i 12.12.12.12/32 None 20
220.0.0.2 None -
14
Rejected by Default action
*i 220.0.0.2/32 None None
220.0.0.2 None -
14
Rejected by Default action
*i 220.0.0.3/32 None 10
220.0.0.2 None -
14
Rejected by Default action
u*>i 221.0.0.2/32 None None
220.0.0.2 None -
14
-------------------------------------------------------------------------------
Total Routes : 17 Routes rejected : 16
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 prefix 4.0.0.1/32 detail neighbor
220.0.0.2 display-rejects
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Rejected by Default action
Network : 4.0.0.1/32
Nexthop : 220.0.0.2
Path Id : None
From : 220.0.0.2
Res. Nexthop : 10.14.0.4
Local Pref. : None Interface Name : to-sim-6
Aggregator AS : None Aggregator : None
Atomic Aggr. : Not Atomic MED : None
AIGP Metric : None
Connector : None
Community : target:65530:20
Cluster : No Cluster Members
Originator Id : None Peer Router Id : 14.14.14.10
Fwd Class : None Priority : None
Flags : Used Valid Best Incomplete
Route Source : External
AS-Path : 14
-------------------------------------------------------------------------------
Total Routes : 1 Routes rejected : 1
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.6/32
neighbor 220.0.0.2
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Accepted by Policy
-------------------------------------------------------------------------------
Original Attributes
Network : 4.0.0.6/32
Nexthop : 220.0.0.2
Path Id : None
From : 220.0.0.2
Res. Nexthop : 10.14.0.4
Local Pref. : n/a Interface Name : to-sim-6
Aggregator AS : None Aggregator : None
Atomic Aggr. : Not Atomic MED : None
AIGP Metric : None
Connector : None
Community : target:65530:20
Cluster : No Cluster Members
Originator Id : None Peer Router Id : 14.14.14.10
Fwd Class : None Priority : None
Flags : Used Valid Best Incomplete
Route Source : External
AS-Path : 14
Modified Attributes
Network : 4.0.0.6/32
Nexthop : 220.0.0.2
Path Id : None
From : 220.0.0.2
Res. Nexthop : 10.14.0.4
Local Pref. : None Interface Name : to-sim-6
Aggregator AS : None Aggregator : None
Atomic Aggr. : Not Atomic MED : None
AIGP Metric : None
Connector : None
Community : 2:11 2:12 2:13 target:65530:20
Cluster : No Cluster Members
Originator Id : None Peer Router Id : 14.14.14.10
Fwd Class : None Priority : None
Flags : Used Valid Best Incomplete
Route Source : External
AS-Path : 14
-------------------------------------------------------------------------------
Routes : 1
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.6/32
longer neighbor 220.0.0.2
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network LocalPref MED
Nexthop Path-Id VPNLabel
As-Path
-------------------------------------------------------------------------------
Accepted by Policy
u*>? 4.0.0.6/32 None None
220.0.0.2 None -
14
-------------------------------------------------------------------------------
Routes : 1
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.6/32
longer neighbor 220.0.0.2 detail
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network
-------------------------------------------------------------------------------
Accepted by Policy
u*>? 4.0.0.6/32
-------------------------------------------------------------------------------
Routes : 1
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.0/24
longer neighbor 220.0.0.2 brief
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network
-------------------------------------------------------------------------------
Accepted by Policy
u*>? 4.0.0.6/32
-------------------------------------------------------------------------------
Total Routes : 6 Routes rejected : 5
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.0/24
longer neighbor 220.0.0.2 display-rejects detail
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network
-------------------------------------------------------------------------------
Rejected by Default action
u*>? 4.0.0.1/32
Rejected by Default action
u*>? 4.0.0.2/32
Rejected by Default action
u*>? 4.0.0.3/32
Rejected by Default action
u*>? 4.0.0.4/32
Rejected by Default action
u*>? 4.0.0.5/32
Accepted by Policy
u*>? 4.0.0.6/32
-------------------------------------------------------------------------------
Total Routes : 6 Routes rejected : 5
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.0/24
longer neighbor 220.0.0.2 display-rejects
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network LocalPref MED
Nexthop Path-Id VPNLabel
As-Path
-------------------------------------------------------------------------------
Rejected by Default action
u*>? 4.0.0.1/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.2/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.3/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.4/32 None None
220.0.0.2 None -
14
Rejected by Default action
u*>? 4.0.0.5/32 None None
220.0.0.2 None -
14
Accepted by Policy
u*>? 4.0.0.6/32 None None
220.0.0.2 None -
14
-------------------------------------------------------------------------------
Total Routes : 6 Routes rejected : 5
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.0/24
longer neighbor 220.0.0.2 display-rejects brief
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network
-------------------------------------------------------------------------------
Rejected by Default action
u*>? 4.0.0.1/32
Rejected by Default action
u*>? 4.0.0.2/32
Rejected by Default action
u*>? 4.0.0.3/32
Rejected by Default action
u*>? 4.0.0.4/32
Rejected by Default action
u*>? 4.0.0.5/32
Accepted by Policy
u*>? 4.0.0.6/32
-------------------------------------------------------------------------------
Total Routes : 6 Routes rejected : 5
===============================================================================
A:sim-1# show router bgp policy-test bgpprefix6 family ipv4 prefix 4.0.0.0/24
longer neighbor 220.0.0.2
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP IPv4 Routes
===============================================================================
Flag Network LocalPref MED
Nexthop Path-Id VPNLabel
As-Path
-------------------------------------------------------------------------------
Accepted by Policy
u*>? 4.0.0.6/32 None None
220.0.0.2 None -
14
-------------------------------------------------------------------------------
Total Routes : 6 Routes rejected : 5
A:sim-1# show router bgp policy-test bgpprefix44rj family vpn-ipv4 prefix 0.0.0.0/0
longer neighbor display-rejects
===============================================================================
BGP Router ID:11.11.11.10 AS:11 Local AS:11
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best, b - backup
===============================================================================
BGP VPN-IPv4 Routes
===============================================================================
Flag Network LocalPref MED
Nexthop Path-Id VPNLabel
As-Path
-------------------------------------------------------------------------------
Accepted by Policy
u*>i 1:30:192.14.15.0/24 None None
220.0.0.2 None 131069
14
Accepted by Policy
u*>i 65530:20:8.0.0.1/32 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:10.0.3.0/24 None None
220.0.0.2 None 131070
14 101
Accepted by Policy
u*>i 65530:20:10.13.0.0/24 None None
220.0.0.2 None 131070
14 101
Accepted by Policy
u*>i 65530:20:10.23.0.0/24 None None
220.0.0.2 None 131070
14 101
Accepted by Policy
u*>i 65530:20:13.13.13.13/32 None None
220.0.0.2 None 131070
14 101
Accepted by Policy
u*>i 65530:20:20.20.20.5/32 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:20.20.20.6/32 None None
220.0.0.2 None 131070
14
Rejected by Policy Entry = 10
u*>i 65530:20:44.44.44.0/24 None None
220.0.0.2 None 131070
14 101
Accepted by Policy
u*>i 65530:20:192.14.15.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.16.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.17.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.18.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.19.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.20.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.21.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.22.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.23.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:192.14.25.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 65530:20:196.34.0.0/24 None None
220.0.0.2 None 131070
14
Accepted by Policy
u*>i 220.0.0.2:50:192.50.50.0/24 None None
220.0.0.2 None 131067
14
Accepted by Policy
u*>i 220.0.0.2:50:220.0.0.2/32 None None
220.0.0.2 None 131067
14
-------------------------------------------------------------------------------
Total Routes : 22 Routes rejected : 1
===============================================================================
|
Field |
Description |
|---|---|
|
Status codes |
Codes used for used, suppressed, history, decayed or valid status |
|
Origin codes |
Codes used for IGP, EGP, incomplete, best or backup origin |
|
Flag |
Indicator for network, nexthop or as-path routes |
pool
pool
Syntax
pool pool-name
Context
[Tree] (tools>perform>router>dhcp>server pool)
[Tree] (tools>perform>router>dhcp6>server pool)
Full Context
tools perform router dhcp local-dhcp-server pool
tools perform router dhcp6 local-dhcp-server pool
Description
This command performs local DHCP or DHCP6 server IP address pool tasks.
Parameters
- pool-name
-
Specifies the pool name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pool
Syntax
pool pool-name
pool
Context
[Tree] (show>router>nat pool)
Full Context
show router nat pool
Description
This command displays NAT pool information.
Parameters
- pool-name
-
Specifies the pool name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of this command.
Output Exampleshow router nat pool
===============================================================================
NAT pools
===============================================================================
Pool NAT-group Type Admin-state
-------------------------------------------------------------------------------
MyPool 1 l2Aware inService
MyPool2 1 l2Aware inService
-------------------------------------------------------------------------------
No. of pools: 2
===============================================================================
*A:SR12_PPPOE>show>router>nat# show router "Base" nat pool "privpool"
===============================================================================
NAT Pool privpool
===============================================================================
ISA NAT Group : 3
Pool type : largeScale
Admin state : inService
Mode : auto (napt)
Port forwarding range : 1 - 1023
Port reservation : 128 blocks
Block usage High Watermark (%) : (Not Specified)
Block usage Low Watermark (%) : (Not Specified)
Subscriber limit per IP address : 65535
Active : true
Last Mgmt Change : 01/28/2012 14:47:59
===============================================================================
NAT address ranges of pool privpool
===============================================================================
Range Drain Num-blk
-------------------------------------------------------------------------------
10.0.0.5 - 10.0.0.6 1
-------------------------------------------------------------------------------
No. of ranges: 1
===============================================================================
NAT members of pool privpool ISA NAT group 3
===============================================================================
Member Block-Usage-% Hi
-------------------------------------------------------------------------------
1 < 1 N
2 < 1 N
-------------------------------------------------------------------------------
No. of members: 2
===============================================================================
A:SR12_PPPOE#
pool-ext-stats
pool-ext-stats
Syntax
pool-ext-stats [pool-name]
Context
[Tree] (show>router>dhcp>server pool-ext-stats)
Full Context
show router dhcp local-dhcp-server pool-ext-stats
Description
This command displays extended statistics per DHCPv4 pool in local DHCPv4 server.
The following statistics are included in output:
-
The number of stable leases in the pool
-
The number of provisioned address in the pool
-
The number of used address in the pool
-
The number of free address in the pool
-
The percentage of used address
-
The percentage of free address
For each statistic (except for provisioned addresses), there is current value and peak value, peak value is the highest value since pool creation or last reset via the clear router rt-id dhcp local-dhcp-server svr-name pool-ext-stats command.
Parameters
- pool-name
-
Specifies the name of DHCPv4 local server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of pool extended statistics information.
Output Exampleshow router 500 dhcp local-dhcp-server "d4" pool-ext-stats "pool-1"
===============================================================================
Extended pool statistics for server "d4"
===============================================================================
Current Peak TimeStamp
-------------------------------------------------------------------------------
Pool pool-1
Local:
Stable Leases 0 0 01/07/2013 19:07:11
Provisioned Addresses 101
Used Addresses 0 0 01/07/2013 19:07:11
Free Addresses 101 101 01/07/2013 19:07:11
Used Pct 0 0 01/07/2013 19:07:11
Free Pct 100 100 01/07/2013 19:07:11
Last Reset Time 01/07/2013 19:07:11
-------------------------------------------------------------------------------
Number of entries 1
===============================================================================Extended Pool Statistics Field Descriptions describes extended pool statistics output fields.
|
Field |
Description |
|---|---|
|
Current |
The current pool statistics |
|
Peak |
The peak value since the last reset |
|
Timestamp |
The date and time of the last reset |
|
Pool |
The pool name |
|
Stable Leases |
The number of stable leases in the pool |
|
Provisioned Addresses |
The number of provisioned addresses in the pool |
|
Used Addressed |
The number of used addresses in the pool |
|
Free Addresses |
The number of free addresses in the pool |
|
Used Pct |
The percentage of subnets in use in the pool |
|
Free Pct |
The percentage of unused subnets in the pool |
|
Last Reset Time |
The date and time of the last reset in the pool |
|
Number of entries |
The total number of entries |
pool-ext-stats
Syntax
pool-ext-stats [pool-name]
Context
[Tree] (show>router>dhcp6>server pool-ext-stats)
Full Context
show router dhcp6 local-dhcp-server pool-ext-stats
Description
This command displays extended statistics per DHCPv6 pool in local DHCPv6 server.
The following statistics are included in output:
-
The number of stable leases in the pool
-
The number of provisioned /64 address block in the pool
-
The number of used /64 address block in the pool
-
The number of free /64 address block in the pool
-
The percentage of used address (with /64 address block)
-
The percentage of free address (with /64 address block)
For each statistic (except for Provisioned Addresses), there is current value and peak value, peak value is the highest value since pool creation or last reset via command "clear router <rt-id> dhcp6 local-dhcp-server <svr-name> pool-ext-stats”.
Parameters
- pool-name
-
Specifies the name of DHCPv6 local server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subnet statistics information.
Output Exampleshow router 500 dhcp6 local-dhcp-server "d6" pool-ext-stats "pool-v6"
===============================================================================
Extended pool statistics for server "d6"
===============================================================================
Current Peak TimeStamp
-------------------------------------------------------------------------------
Pool pool-v6
Local:
Stable Leases 0 0 01/07/2013 19:54:52
Provisioned Blks 4
Used Blks 0 0 01/07/2013 19:54:52
Free Blks 4 4 01/07/2013 19:54:52
Used Pct 0 0 01/07/2013 19:54:52
Free Pct 100 100 01/07/2013 19:54:52
Last Reset Time 01/07/2013 19:54:52
-------------------------------------------------------------------------------
Number of entries 1
===============================================================================
DHCP6 Pool Ext Stats Field Descriptions describes DHCP6 extended pool statistics output fields.
|
Field |
Description |
|---|---|
|
Current |
The current pool statistics |
|
Peak |
The peak value since the last reset |
|
TimeStamp |
The date and time of the last reset |
|
Pool |
The pool name |
|
Stable Leases |
The number of stable leases |
|
Provisioned Blks |
The number of provisioned blocks in this pool |
|
Free Blks |
The number of free blocks in this pool |
|
Used Pct |
The percentage of extended statistics in use |
|
Free Pct |
The percentage of /64 blocks currently unused |
|
Last Reset Time |
The date and time of the last reset |
|
Number of entries |
The total number of entries |
pool-ext-stats
Syntax
pool-ext-stats [pool-name]
Context
[Tree] (clear>router>dhcp>server pool-ext-stats)
[Tree] (clear>router>dhcp6>server pool-ext-stats)
Full Context
clear router dhcp local-dhcp-server pool-ext-stats
clear router dhcp6 local-dhcp-server pool-ext-stats
Description
This command clears extended pool statistics.
Parameters
- pool-name
-
Clears information about the pool name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pool-stats
pool-stats
Syntax
pool-stats [pool-name]
Context
[Tree] (show>router>dhcp6>server pool-stats)
Full Context
show router dhcp6 local-dhcp-server pool-stats
Description
This command displays pool statistics.
Parameters
- pool-name
-
Specifies the name of DHCPv6 local server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of pool statistics information.
Output Example*A:vsim-2# show router 500 dhcp6 local-dhcp-server "d6" pool-stats
===============================================================================
DHCPv6 server pool statistics
===============================================================================
Pool : v6-1
-------------------------------------------------------------------------------
Dropped Int no prefix WAN : 0
Dropped Int no prefix SLAAC : 0
===============================================================================
*A:vsim-2#
*A:vsim-2# show router 500 dhcp local-dhcp-server "d4" failover-
failover-pool-stats failover-server-stats
*A:vsim-2# show router 500 dhcp local-dhcp-server "d4" failover-pool-stats
==================================================================
Failover config for pool v4-1
==================================================================
Failover Admin State inService
Failover Oper State normal
Failover Persist Key 0xFFFFFFFF
Administrative MCLT 0h10m0s
Operational MCLT 0h10m0s
Startup Wait Time 0h2m0s
Partner Down Delay 23h59m59s
Ignore MCLT disabled
Failover statistics for pool v4-1
------------------------------------------------------------------
Dropped Invalid Packets 0
Failover Shutdown 0
Lease Already Expired 0
Maximum Lease Count Reached 0
Subnet Not Found 0
Range Not Found 0
Host Conflict 0
Address Conflict 0
Peer Conflict 0
Persistence Congestion 0
No Lease Hold Time Configured 0
Lease Not Found 0
------------------------------------------------------------------
Number of pools found 1
==================================================================
*A:vsim-2#
Failover Pool Statistics Field Descriptions describes pool statistics output field descriptions.
|
Field |
Description |
|---|---|
|
Failover Admin State |
Identifiers the failover state of the DHCP server instance inService — The failover admin state is in service outOfService — The failover admin state is out of service |
|
Failover Oper State |
The operational state of a DHCP server instance |
|
Failover Persist Key |
The maximum amount of time that one server can extend a lease for a client's binding beyond the time known by the partner server |
|
Administrative MCLT |
The administrative Maximum Client Lead Time (MCLT) |
|
Operational MCLT |
Indicates the operational MCLT |
|
Startup Wait Time |
The startup wait time. The startup wait time is the time that one IP address pool attempts to contact the partner IP address pool. During this time, the IP address pool is unresponsive to DHCP client requests. |
|
Partner Down Delay |
The minimum safe-time after the beginning of COMMUNICATIONS-INTERRUPTED state. After the expiry of this time, the server enters the PARTNER-DOWN state. |
|
Ignore McLT |
The ignore McLT status. If, after the transition COMMUNICATIONS-INTERRUPTED-to-PARTNER-DOWN state, the DHCP server instance ignores the safety period with a duration of Maximum Client Lead Time; a 'true’ value has the effect that the DHCP server starts offering IP addresses from the partner's scope immediately after this transition, without waiting for existing leases allocated by the partner and not known by this system to time out. A 'true’ value increases the risk that duplicate addresses are offered; if the transition to PARTNER-DOWN state is likely to be caused by a failure of the partner system rather than a communications problem, this risk is reduced. |
|
Failover statistics for pool |
The failover statistics for each pool |
|
Dropped Invalid Packets |
The number of BNDUPD packets that were dropped because the packet was malformed |
|
Failover Shutdown |
The number of BNDUPD packets that were dropped because the failover state if the DHCP server instance is shut down |
|
Lease Already Expired |
The number of BNDUPD packets that were dropped because the corresponding lease has expired |
|
Maximum Lease Count Reached |
The number of BNDUPD packets that were dropped because the maximum number of leases were reached |
|
Subnet Not Found |
The number of BNDUPD packets that were dropped because a valid subnet could not be found for the lease |
|
Range Not Found |
The number of BNDUPD packets that were dropped because a valid include range could not be found for the lease. |
|
Host Conflict |
The number of BNDUPD packets that were dropped because this DHCP server instance has already leased this address to another host |
|
Address Conflict |
The number of BNDUPD packets that were dropped because this DHCP server instance has already leased another address to this host |
|
Peer Conflict |
The number of BNDUPD packets that were dropped because the failover peer has leased an address within a subnet range of which the failover control is set to local on this local DHCP server instance |
|
Persist Congestion |
The number of BNDUPD packets that were dropped because of persistence congestion on this DHCP server instance |
|
No Lease Hold Time Configured |
The number of BNDUPD packets that were dropped because the lease hold time is zero on this DHCP server instance |
|
Lease Not Found |
The number of Binding Database Update (BNDUPD) remove packets were dropped because the corresponding lease could not be found. |
|
Number of pools found |
The total number of pools found |
pool-threshold-stats
pool-threshold-stats
Syntax
pool-threshold-stats [pool-name] detail [ format {exact | scientific}]
pool-threshold-stats [pool-name]
Context
[Tree] (show>router>dhcp6>server pool-threshold-stats)
Full Context
show router dhcp6 local-dhcp-server pool-threshold-stats
Description
This commands displays pool level threshold stats of local DHCPv6 server. A minimum-free threshold needs to be configured before system collects threshold stats for the prefix.
The stats for each threshold are calculated based on the configured minimum-free prefix length.
For example, a /59 prefix is provision in the local DHCPv6 server, and the server allocated two PD leases, one /62 and one /63. And there is a /63 minimum threshold configured. The threshold stats are calculated based on /63 as the base unit (block). Then the value of current used block would be 3 because there is one /62 lease and one /63 lease, that equals to a total of three /63.
Parameters
- pool-name
-
Specifies the name of the pool in local DHCPv6 server.
- detail
-
Displays detailed output.
- format
-
Specifies the format in the display to be either exact or scientific.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of pool threshold statistics information.
Output Exampleshow router 500 dhcp6 local-dhcp-server "d6" pool-threshold-stats "1"
===============================================================================
Server "d6"
===============================================================================
Operational state : inService
-------------------------------------------------------------------------------
Pool : 1
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
-----------------------------------------------------------------------------
Threshold Used Peak Too low Depleted Peak timestamp
-----------------------------------------------------------------------------
/62 25% 25% N N 01/21/2015 21:52:12
/63 19% 19% N N 01/21/2015 21:52:12
The command shown above displays an overview of pool level thresholds in the specified pool:
-
The Peak field indicates the peak value of used
-
The Too low field indicate if the configured minimum-free threshold is exceeded
-
The Depleted field indicate if there is no available prefix with the length in the provisioned prefix
-
The Peak timestamp field indicates the time of peak used value
show router 500 dhcp6 local-dhcp-server "d6" pool-threshold-stats "1" detail
===============================================================================
Server "d6"
===============================================================================
Operational state : inService
-------------------------------------------------------------------------------
Pool : 1
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
-----------------------------------------------------------------------------
Threshold : /62
-----------------------------------------------------------------------------
Current Provisioned Blks : 8.000000x10^0
Current Used Blks : 2.000000x10^0
Current Free Blks : 6.000000x10^0
Current Used Percent : 25%
Current Used Peak Blks : 2.000000x10^0
Current Used Peak Percent : 25%
Current Used Peak Time : 01/21/2015 21:52:12
Current Free Percent : 75%
Current Free Too Low : N
Current Free Depleted : N
Local Provisioned Blks : 8.000000x10^0
Local Used Blks : 2.000000x10^0
Local Free Blks : 6.000000x10^0
Local Used Peak Blks : 2.000000x10^0
Local Used Peak Percent : 25%
Local Used Peak Time : 01/21/2015 21:52:12
Remote Provisioned Blks : 0.000000x10^0
Remote Used Blks : 0.000000x10^0
Remote Free Blks : 0.000000x10^0
Remote Used Peak Blks : 0.000000x10^0
Remote Used Peak Percent : 0%
Remote Used Peak Time : 01/21/2015 21:47:39
Peak Reset Time : 01/21/2015 21:47:39
Valid Data : Y
-----------------------------------------------------------------------------
Threshold : /63
-----------------------------------------------------------------------------
Current Provisioned Blks : 1.600000x10^1
Current Used Blks : 3.000000x10^0
Current Free Blks : 1.300000x10^1
Current Used Percent : 19%
Current Used Peak Blks : 3.000000x10^0
Current Used Peak Percent : 19%
Current Used Peak Time : 01/21/2015 21:52:12
Current Free Percent : 81%
Current Free Too Low : N
Current Free Depleted : N
Local Provisioned Blks : 1.600000x10^1
Local Used Blks : 3.000000x10^0
Local Free Blks : 1.300000x10^1
Local Used Peak Blks : 3.000000x10^0
Local Used Peak Percent : 19%
Local Used Peak Time : 01/21/2015 21:52:12
Remote Provisioned Blks : 0.000000x10^0
Remote Used Blks : 0.000000x10^0
Remote Free Blks : 0.000000x10^0
Remote Used Peak Blks : 0.000000x10^0
Remote Used Peak Percent : 0%
Remote Used Peak Time : 01/21/2015 21:47:39
Peak Reset Time : 01/21/2015 21:47:39
Valid Data : Y
The above command displays detailed statistics of all pool level thresholds in the specified pool:
-
Blks in the output means the minimum free prefix length.
-
Valid Data output indicates whether the data you see is valid or not. The data is invalid when a background stats update is scheduled or busy.
Pool Threshold Statistics Field Descriptions describes pool threshold statistics output fields.
|
Field |
Description |
|---|---|
|
Operational state |
The operational state of the local DHCP server instance unknown — The operational state is unknown inService — The operational state is in service outOfService — The operational state is out of service transition — The operational state is in transition waitPersistence — The DHCP server instance is waiting for a persistence action to complete. |
|
Pool |
The pool ID |
|
Stable Leases |
The number of stable leases |
|
Advertised leases |
The number of advertised leases |
|
Threshold |
The prefix level threshold |
|
Current Provisioned Blks |
The number of provisioned blocks in this pool |
|
Current Used Blks |
The number of used blocks in this pool |
|
Current Free Blks |
The number of free blocks in this pool |
|
Current Used Percent |
The percentage of used prefixes with the minimum free threshold length in the pool compared to the number of provisioned prefixes |
|
Current Used Peak Blks |
A 64-bit word of the peak value of the number of used blocks in the pool with a prefix length |
|
Current Used Peak Percent |
The peak value of the number of used prefixes with the minimum free threshold length in the pool as a percentage of the provisioned prefixes. This depends on the current failover state of the DHCP server or pool |
|
Current Used Peak Time |
The time at which the peak value of the number of used prefixes in the pool was reached |
|
Current Free Percent |
The percentage of free prefixes with the minimum free threshold length in the pool compared to the number of provisioned prefixes. This depends on the current failover state of the DHCP server or pool |
|
Current Free Too Low |
The number of free prefixes with the minimum free threshold length available in the pool that is below the configured number of prefixes with the minimum free threshold length |
|
Current Free Depleted |
The number of prefixes with the minimum free threshold length available in the pool |
|
Local Provisioned Blks |
A 64-bit word of the number of provisioned prefixes with the minimum free threshold length local in the pool |
|
Local Used Blks |
A 64-bit word of the number of used prefixes with the minimum free threshold length local in the pool |
|
Local Free Blks |
A 64-bit word of the number of free prefixes with the minimum free threshold length local in the pool |
|
Local Used Peak Blks |
A 64-bit word of the peak value of the number of used prefixes with the minimum free threshold length local in the pool |
|
Local Used Peak Percent |
The peak value of the number of used prefixes with the minimum free threshold length local in the pool as a percentage of the provisioned prefixes |
|
Local Used Peak Time |
The time at which the peak value of the number of used prefixes local in the pool was reached |
|
Remote Provisioned Blks |
A 64-bit word of the number of provisioned prefixes with the minimum free threshold length remote in the pool |
|
Remote Used Blks |
A 64-bit word of the number of used prefixes with the minimum free threshold length remote in the pool |
|
Remote Free Blks |
A 64-bit word of the number of free prefixes with the minimum free threshold length remote in the pool |
pool-threshold-stats
Syntax
pool-threshold-stats [pool-name]
Context
[Tree] (clear>router>dhcp6>server pool-threshold-stats)
Full Context
clear router dhcp6 local-dhcp-server pool-threshold-stats
Description
This commands resets the peak stats in the pool level threshold stats in the specified pool. If the pool name is not specified, then the peak stats in all pools in the server are reset.
Parameters
- pool-name
-
Clears information about the specified local DHCPv6 server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pools
pools
Syntax
pools mda-id[/port]
pools mda-id[/port] access-app [pool-name]
pools mda-id[/port] access-app [service service-id]
pools mda-id[/port] access-app queue-group queue-group-name [instance instance-id]
pools mda-id[/port] network-egress [pool-name]
pools mda-id[/port] network-egress queue-group queue-group-name [instance instance-id]
pools mda-id[/port] [direction [{pool-name | service service-id | queue-group queue-group-name} [instance instance-id]]]
pools slot-number
pools slot-number fp fp-number
pools slot-number fp fp-number app-ingress
pools slot-number fp fp-number network-ingress statistics
pools port access-app statistics
pools port network-egress statistics
Context
[Tree] (show pools)
Full Context
show pools
Description
This command displays pool information.
Parameters
- mda-id[/port]
-
Displays the pool information of the specified MDA and port.
- access-app
-
Specifies the pool application as either access ingress or egress.
- pool-name
-
Displays the pool information of the specified pool. If specified, the name must be default.
- service-id
-
Displays the pool information for the specified service.
- queue-group-name
-
Displays the information for the specified queue group.
- instance-id
-
Specifies the identification of a specific instance of the queue group.
- network-egress
-
Displays the network egress information.
- direction
-
Displays the information for the ingress or egress direction.
- slot-number
-
Displays the information for the specified card slot.
- fp-number
-
Displays the information for the specified FP.
- app-ingress
-
Displays the network ingress or access ingress information.
- statistics
-
Displays the buffer pool statistics.
Platforms
All
Output
The following outputs are example of pool information, and Output Fields: show pools describes the output fields.
The pool shared in use stat only increases when a queue is asking for a buffer outside its reserved size. If all the buffers in a pool are assigned to queues within their reserved size, then only the reserved in use size will increase. In case of resv CBS over subscription (CBS sum for all queues is bigger than pool resvCbs), it is possible that pool resv in use stat can increase above the actual pool reserved size.
*A:PE# show pools 5/1
===============================================================================
MDA Pools
===============================================================================
Slot/MDA App. Pool Name Actual ResvCBS PoolSize
Admin ResvCBS
-------------------------------------------------------------------------------
5/1 Acc-Ing default 0 0
30%
5/1 Acc-Egr default 0 0
30%
5/1 Net-Egr default 0 0
Sum
===============================================================================
===============================================================================
Port Pools
===============================================================================
Port App. Pool Name Actual ResvCBS PoolSize
Admin ResvCBS
-------------------------------------------------------------------------------
5/1/1 Acc-Ing default 16128 52224
30%
5/1/1 Acc-Egr default 23040 75264
30%
5/1/1 Net-Egr default 0 0
Sum
5/1/2 Acc-Ing default 0 0
30%
5/1/2 Acc-Egr default 0 0
30%
5/1/2 Net-Egr default 32256 75264
Sum
5/1/3 Acc-Ing default 0 0
30%
5/1/3 Acc-Egr default 0 0
30%
5/1/3 Net-Egr default 32256 75264
Sum
5/1/4 Acc-Ing default 0 0
30%
5/1/4 Acc-Egr default 0 0
30%
5/1/4 Net-Egr default 32256 75264
Sum
5/1/5 Acc-Ing default 0 0
30%
5/1/5 Acc-Egr default 0 0
30%
5/1/5 Net-Egr default 32256 75264
Sum
===============================================================================
*A:PE#
*A:PE# show pools 5/1/5 network-egress
===============================================================================
Pool Information
===============================================================================
Port : 5/1/5
Application : Net-Egr Pool Name : default
CLI Config. Resv CBS : Sum
Resv CBS Step : 0% Resv CBS Max : 0%
Amber Alarm Threshold: 0% Red Alarm Threshold : 0%
-------------------------------------------------------------------------------
Queue-Groups
-------------------------------------------------------------------------------
Queue-Group:Instance : qg1:1
-------------------------------------------------------------------------------
Utilization State Start-Avg Max-Avg Max-Prob
-------------------------------------------------------------------------------
HiPlus-Slope Down 85% 100% 80%
High-Slope Down 70% 90% 80%
Low-Slope Down 50% 75% 80%
Exceed-Slope Down 30% 55% 80%
Time Avg Factor : 7
Pool Total : 75264 KB
Pool Shared : 43008 KB Pool Resv : 32256 KB
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Current Resv CBS Provisioned Rising Falling Alarm
%age all Queues Alarm Thd Alarm Thd Color
-------------------------------------------------------------------------------
Sum 32232 KB NA NA Green
Pool Total In Use : 0 KB
Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB
WA Shared In Use : 0 KB
HiPlus-Slope Drop Pr*: 0 Hi-Slope Drop Prob : 0
Lo-Slope Drop Prob : 0 Excd-Slope Drop Prob : 0
===============================================================================
Queue Information
===============================================================================
===============================================================================
Queue : 1 Net=be Port=5/1/5
===============================================================================
FC Map : be
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 37632 KB Oper MBS : 37632 KB
High-Plus Drop T*: 37632 KB High Drop Tail : 37632 KB
Low Drop Tail : 33792 KB Exceed Drop Tail : 33792 KB
CBS : 744 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 2 Net=l2 Port=5/1/5
===============================================================================
FC Map : l2
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 37632 KB Oper MBS : 37632 KB
High-Plus Drop T*: 37632 KB High Drop Tail : 37632 KB
Low Drop Tail : 33792 KB Exceed Drop Tail : 33792 KB
CBS : 2256 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 3 Net=af Port=5/1/5
===============================================================================
FC Map : af
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 37632 KB Oper MBS : 37632 KB
High-Plus Drop T*: 37632 KB High Drop Tail : 37632 KB
Low Drop Tail : 33792 KB Exceed Drop Tail : 33792 KB
CBS : 7488 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 4 Net=l1 Port=5/1/5
===============================================================================
FC Map : l1
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 18816 KB Oper MBS : 18816 KB
High-Plus Drop T*: 18816 KB High Drop Tail : 18816 KB
Low Drop Tail : 16896 KB Exceed Drop Tail : 16896 KB
CBS : 2256 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 5 Net=h2 Port=5/1/5
===============================================================================
FC Map : h2
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 10000000 Oper CIR : Max
Admin MBS : 37632 KB Oper MBS : 37632 KB
High-Plus Drop T*: 37632 KB High Drop Tail : 37632 KB
Low Drop Tail : 33792 KB Exceed Drop Tail : 33792 KB
CBS : 7488 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 6 Net=ef Port=5/1/5
===============================================================================
FC Map : ef
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 10000000 Oper CIR : Max
Admin MBS : 37632 KB Oper MBS : 37632 KB
High-Plus Drop T*: 37632 KB High Drop Tail : 37632 KB
Low Drop Tail : 33792 KB Exceed Drop Tail : 33792 KB
CBS : 7488 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 7 Net=h1 Port=5/1/5
===============================================================================
FC Map : h1
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 1000000 Oper CIR : 1000000
Admin MBS : 18816 KB Oper MBS : 18816 KB
High-Plus Drop T*: 18816 KB High Drop Tail : 18816 KB
Low Drop Tail : 16896 KB Exceed Drop Tail : 16896 KB
CBS : 2256 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 8 Net=nc Port=5/1/5
===============================================================================
FC Map : nc
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 1000000 Oper CIR : 1000000
Admin MBS : 18816 KB Oper MBS : 18816 KB
High-Plus Drop T*: 18816 KB High Drop Tail : 18816 KB
Low Drop Tail : 16896 KB Exceed Drop Tail : 16896 KB
CBS : 2256 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : netQGrp->qg1:1(5/1/5)->1
===============================================================================
FC Map : not-applicable
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 12288 KB Oper MBS : 12288 KB
High-Plus Drop T*: 12288 KB High Drop Tail : 12288 KB
Low Drop Tail : 10944 KB Exceed Drop Tail : 9792 KB
CBS : 0 KB Depth : 0
Slope : not-applicable
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:PE#
*A:PE# show pools 5/1/1 access-ingress
===============================================================================
Pool Information
===============================================================================
Port : 5/1/1
Application : Acc-Ing Pool Name : default
CLI Config. Resv CBS : 30%(default)
Resv CBS Step : 0% Resv CBS Max : 0%
Amber Alarm Threshold: 0% Red Alarm Threshold : 0%
-------------------------------------------------------------------------------
Utilization State Start-Avg Max-Avg Max-Prob
-------------------------------------------------------------------------------
HiPlus-Slope Down 85% 100% 80%
High-Slope Down 70% 90% 80%
Low-Slope Down 50% 75% 80%
Exceed-Slope Down 30% 55% 80%
Time Avg Factor : 7
Pool Total : 52224 KB
Pool Shared : 36096 KB Pool Resv : 16128 KB
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Current Resv CBS Provisioned Rising Falling Alarm
%age all Queues Alarm Thd Alarm Thd Color
-------------------------------------------------------------------------------
30% 0 KB NA NA Green
Pool Total In Use : 0 KB
Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB
WA Shared In Use : 0 KB
HiPlus-Slope Drop Pr*: 0 Hi-Slope Drop Prob : 0
Lo-Slope Drop Prob : 0 Excd-Slope Drop Prob : 0
===============================================================================
Queue Information
===============================================================================
===============================================================================
Queue : 1->5/1/1:1->1
===============================================================================
FC Map : be l2 af l1 h2 ef h1 nc
Dest Tap : 5/1 Dest FP : 1
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin FIR : 0 Oper FIR : 0
Admin MBS : 12288 KB Oper MBS : 12288 KB
High-Plus Drop Tail : 12288 KB High Drop Tail : 12288 KB
Low Drop Tail : 10944 KB Exceed Drop Tail : 9792 KB
CBS : 0 KB Depth : 0
Slope : not-applicable
===============================================================================
===============================================================================
Queue : 1->5/1/1:1->11
===============================================================================
FC Map : be l2 af l1 h2 ef h1 nc
Dest Tap : MCast Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin FIR : 0 Oper FIR : 0
Admin MBS : 12288 KB Oper MBS : 12288 KB
High-Plus Drop Tail : 12288 KB High Drop Tail : 12288 KB
Low Drop Tail : 10944 KB Exceed Drop Tail : 9792 KB
CBS : 0 KB Depth : 0
Slope : not-applicable
===============================================================================
No Matching Entries
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:PE#
*A:PE# show pools 5/1/1 access-egress
===============================================================================
Pool Information
===============================================================================
Port : 5/1/1
Application : Acc-Egr Pool Name : default
CLI Config. Resv CBS : 30%(default)
Resv CBS Step : 0% Resv CBS Max : 0%
Amber Alarm Threshold: 0% Red Alarm Threshold : 0%
-------------------------------------------------------------------------------
Queue-Groups
-------------------------------------------------------------------------------
Queue-Group:Instance : policer-output-queues:1
-------------------------------------------------------------------------------
Utilization State Start-Avg Max-Avg Max-Prob
-------------------------------------------------------------------------------
HiPlus-Slope Down 85% 100% 80%
High-Slope Down 70% 90% 80%
Low-Slope Down 50% 75% 80%
Exceed-Slope Down 30% 55% 80%
Time Avg Factor : 7
Pool Total : 75264 KB
Pool Shared : 52224 KB Pool Resv : 23040 KB
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Current Resv CBS Provisioned Rising Falling Alarm
%age all Queues Alarm Thd Alarm Thd Color
-------------------------------------------------------------------------------
30% 0 KB NA NA Green
Pool Total In Use : 0 KB
Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB
WA Shared In Use : 0 KB
HiPlus-Slope Drop Pr*: 0 Hi-Slope Drop Prob : 0
Lo-Slope Drop Prob : 0 Excd-Slope Drop Prob : 0
===============================================================================
Queue Information
===============================================================================
===============================================================================
Queue : 1->5/1/1:1->1
===============================================================================
FC Map : be l2 af l1 h2 ef h1 nc
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 12288 KB Oper MBS : 12288 KB
High-Plus Drop Tail : 12288 KB High Drop Tail : 12288 KB
Low Drop Tail : 10944 KB Exceed Drop Tail : 9792 KB
CBS : 0 KB Depth : 0
Slope : not-applicable
===============================================================================
===============================================================================
Queue : accQGrp->policer-output-queues:1(5/1/1)->1
===============================================================================
FC Map : not-applicable
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 12288 KB Oper MBS : 12288 KB
High-Plus Drop Tail : 12288 KB High Drop Tail : 12288 KB
Low Drop Tail : 10944 KB Exceed Drop Tail : 9792 KB
CBS : 0 KB Depth : 0
Slope : not-applicable
===============================================================================
===============================================================================
Queue : accQGrp->policer-output-queues:1(5/1/1)->2
===============================================================================
FC Map : not-applicable
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 12288 KB Oper MBS : 12288 KB
High-Plus Drop Tail : 12288 KB High Drop Tail : 12288 KB
Low Drop Tail : 10944 KB Exceed Drop Tail : 9792 KB
CBS : 0 KB Depth : 0
Slope : not-applicable
===============================================================================
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:PE#
:admin@Dut-A# show pools 1/1/c1/1 access-ingress statistics
===============================================================================
Pool Stats Information
===============================================================================
-------------------------------------------------------------------------------
Packets/Octets
-------------------------------------------------------------------------------
Fwd: 15/15000
Drop due to:
Queue: 13038037/13038037000
Exceed-Slope: 0/0
Low-Slope: 0/0
High-Slope: 0/0
HiPlus-Slope: 0/0
Pool Shared: 0/0
Pool Total: 0/0
Other: 0/0
Total: 13038052/13038052000
===============================================================================Output Fields: show pools describes the output fields for the show pools command.
|
Label |
Description |
|---|---|
|
Type |
Specifies the pool type. |
|
ID-FP |
Specifies the card-FP or MDA-FP or card, MDA, or port designation. |
|
Application/Type |
Specifies what the pool would be used for. The pools could be used for access or network traffic at either ingress or egress. |
|
Pool Name |
Specifies the name of the pool being used. |
|
Resv CBS |
Specifies the percentage of pool size reserved for CBS. |
|
Utilization |
Specifies the type of the slope policy. |
|
State |
The administrative status of the port. |
|
Start-Avg |
Specifies the percentage of the buffer utilized after which the drop probability starts to rise above 0. |
|
Max-Avg |
Specifies the percentage of the buffer utilized after which the drop probability is 100 percent. This implies that all packets beyond this point will be dropped. |
|
Time Avg Factor |
Specifies the time average factor the weighting between the previous shared buffer average utilization result and the new shared buffer utilization in determining the new shared buffer average utilization. |
|
Actual ResvCBS |
Specifies the actual percentage of pool size reserved for CBS. |
|
Admin ResvCBS |
Specifies the percentage of pool size reserved for CBS. |
|
PoolSize |
Specifies the size in percentage of buffer space. The value '-1' implies that the pool size should be computed as per fair weighting between all other pools. |
|
Pool Total |
Displays the total pool size. |
|
Pool Shared |
Displays the amount of the pool which is shared. |
|
Pool Resv |
Specifies the percentage of reserved pool size. |
|
Pool Total In Use |
Displays the total amount of the pool which is in use. |
|
Pool Shared In Use |
Displays the amount of the pool which is shared that is in use. |
|
Queue |
Specifies the number of packets/octets discarded in the queue. |
|
Exceed-Slope |
Specifies the number of packets/octets discarded because of wred-slope (exceed). |
|
Low-Slope |
Specifies the number of packets/octets discarded because of wred-slope (low). |
|
High-Slope |
Specifies the number of packets/octets discarded because of wred-slope (high). |
|
HiPlus-Slope |
Specifies the number of packets/octets discarded because of wred-slope (hiPlus). |
|
Pool Shared |
Specifies the number of packets/octets discarded by exceeding shared-buffer-pool size. |
|
Pool Total |
Specifies the number of packets/octets discarded after the total size of the bufferpool is reached. |
pools
Syntax
pools port-id {access-ingress | access-egress | network-egress} statistics
pools slot-number fp fp-number {network-ingress} statistics
Context
[Tree] (clear pools)
Full Context
clear pools
Description
This command clears buffer pool statistics.
Parameters
- port-id
-
Clears information for the specified port.
- slot-number
-
Clears information for the specified card slot.
- fp-number
-
Clears information for the specified FP.
- statistics
-
Clears buffer pool statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS
port
port
Syntax
port [port-id] [statistics [egress-aggregate]] [detail]
port port-id associations
port [port-id] description [detail]
port port-id dotx1 [detail]
port aps
port [port-id] cem
port port-id ethernet [association | detail]
port port-id ethernet [association | detail] efm-oam [event-logs [{failure | degraded}] [{active | cleared}]]
port port-id ethernet [association | detail] lldp [nearest-bridge | nearest-non-tpmr | nearest-customer] [remote-info] [detail]
port A/gnss
port B/gnss
port port-id hs-secondary-shaper secondary-shaper-name [statistics | associations]
port port-id hs-secondary-shaper
port port-id hw-agg-shaper-scheduler [statistics] [monitor-threshold]
port port-id macsec sub-port sub-port-id [detail] [statistics]
port port-id monitor-threshold
port port-id optical
port port-id otu
port port-id port-queues queue queue-id
port port-id port-queues queue-depth [queue queue-id]
port port-id port-scheduler statistics
port port-id queue-group [ingress | egress] [ queue-group-name] [access | network] [instance instance-id]
port port-id queue-group [ingress | egress] [ queue-group-name] [access | network] associations [instance instance-id]
port port-id queue-group [ingress | egress] queue-group-name [access | network] [instance instance-id] queue-depth [queue queue-id]
port port-id queue-group [ingress | egress] [ queue-group-name] [access | network] statistics [instance instance-id]
port port-id queue-group summary
port port-id vport vport-name monitor-threshold
Context
[Tree] (show port)
Full Context
show port
Description
This command displays port or channel information.
If the port-id parameter only specifies a portion of a port identifier, a summary of all ports that start with that portion is displayed. For example, specifying a slot number and MDA number displays a summary of all ports on that MDA. If no port-id is provided, a summary of all ports in the system is displayed.
If the detail keyword is specified without any port-id, the detailed output of every port is displayed. This is useful for generating a complete report or as an input into the | match post-filtering command to display only specific fields for all ports (customized summaries).
If the port-id specifies a unique port, information about that port is displayed. The specific information displayed depends on the type of port. Additional information can be displayed if the detail keyword is included. In addition, information subsets can be displayed by using various keywords. For example, the otu keyword displays only the OTU interface information for the port.
When the associations keyword is specified and the port-id is a member of a LAG, the command is interpreted as a request to display the associations of that LAG (see the show lag lag-id associations command).
Parameters
- port-id
-
Specifies the physical port ID in the form slot/mda/port. The following table describes the port ID values.
Table 33. Port ID values Product
Slot
MDA
Port
Values
7750 SR-12
1 to 10
1, 2
1 to 60
(depending on the MDA type)
—
7750 SR-7
1 to 5
1, 2
—
7950 XRS
1 to 20
—
—
7450 ESS-7
—
—
1 to 4
7450 ESS-12
—
—
1 to 0
7750 SR single-slot FP5
—
—
A/gnss
7750 SR-2se
—
—
A/gnss
B/gnss
Channelized MDAs
CHOC12-SFP
—
slot/mda/port [1 to 4]. [1 to 3]. [1 to 28]. [..24]
For example, 7/2/1.1.1.28.24
CHOC3-SFP
—
slot/mda/port. [1 to 3]. [1 to 28]. [..24]
For example, 7/2/1.1.28.24
DS3
—
slot/mda/port. [1 to 28] . [..24]
For example, 7/1/1.1.1
- access
-
Specifies that the queue group name is on an access port.
- active
-
Keyword to display only active events.
- aps
-
Displays ports on APS groups.
- associations
-
Displays a list of port association.
- cem
-
Displays CEM encap ports and channels.
- cleared
-
Keyword to display remote information about the bridge MAC.
- degraded
-
Keyword to display degrade severity events.
- description
-
Displays port description strings.
- detail
-
Provides detailed information.
- dot1x
-
Displays information about 802.1x status and statistics.
- egress
-
Specifies whether the queue group name is an egress policy.
- egress-aggregate
-
Displays aggregate egress statistics.
- ethernet
-
Displays Ethernet port information.
- failure
-
Keyword to display failure severity events.
- A/gnss
-
Displays interface information for the GNSS port on CPM A.
- B/gnss
-
Displays interface information for the GNSS port on CPM B.
- hs-secondary-shaper
-
Displays information about a specific HS secondary shaper on a port.
- ingress
-
Specifies whether the queue group name is an ingress policy.
- instance-id
-
Specifies the identification of a specific instance of the queue group.
- macsec
-
Displays the MACsec information for the port.
- monitor-threshold
-
Displays the exceed-count for the port-scheduler under Vport (if specified) or for a physical port.
- optical
-
Displays optical information.
- otu
-
Displays optical transport unit (OTU) information.
- nearest-bridge
-
Displays nearest bridge information.
- nearest-customer
-
Displays nearest customer information.
- nearest-non-tpmr
-
Displays nearest Two-Port MAC Relay (TPMR) information.
- network
-
Specifies that the queue group name is on a network port.
- port-scheduler
-
Displays the packet and octet counters for traffic exiting the specified port with an applied port scheduler policy, showing the total forwarded and dropped packets and octets, and the forwarded and dropped packets and octets per level.
- queue
-
Displays the queue information.
- queue-depth
-
Displays queue depth information for the specified queue group queue.
- queue-group
-
Displays the queue group information.
- queue-group-name
-
Specifies the name of an existing queue group template, up to 32 characters.
- queue-id
-
Specifies the queue identification.
- remote-info
-
Displays remote information about the bridge MAC.
- secondary-shaper-name
-
Displays information about the HS secondary name, up to 32 characters.
- statistics
-
Displays port statistics.
- vport-name
-
Specifies the name of the Vport up, to 32 characters in length.
Platforms
All
Output
The following sections provide output examples. Output Fields: show port <port-id> provides an alphabetized list of descriptions for the output fields.
-
Output Example: show port <port-id> (Summary Table of Ports)
-
Output Example: show port <port-id> detail (Ethernet Interface Port)
-
Output Example: show port <port-id> (Excerpt Showing CFP Port with a QSFP28 Adapter)
-
Output Example: show port <port-id> ethernet efm-oam event-logs
-
Output Example: show port <port-id> ethernet efm-oam event-logs
-
Output Example: show port <port-id> ethernet lldp remote-info detail
-
Output Example: show port <port-id> macsec sub-port <sub-port-id> detail
-
Output Example: show port <port-id> macsec sub-port <sub-port-id> statistics
-
Output Example: show port <port-id> for a QSFP-LS optical line system
-
Output Example: show port <port-id> port-scheduler statistics
-
Output Example: show port <port-id> port-queues queue <queue-id>
-
Output Example: show port <port-id> (Showing Channelized Ports)
-
Output Example: show port <port-id> [statistics [egress-aggregate]] [detail]
-
Output Example: show port detail for a satellite uplink port
-
Output Example: show port detail for a satellite client port
*A:cses-V22# show port
===============================================================================
Ports on Slot 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
1/1/1 Down Yes Up 8704 8704 - netw null xcme GIGE-LX 10KM
1/1/2 Up Yes Up 1514 1514 - accs null xcme GIGE-LX 10KM
1/1/3 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/4 Up Yes Up 1514 1514 - accs null xcme GIGE-LX 10KM
1/1/5 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/6 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/7 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/8 Up Yes Up 8704 8704 - hybr dotq xcme GIGE-LX 10KM
1/1/9 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/10 Down Yes Down 8704 8704 - netw null xcme GIGE-LX 10KM
A:admin@mci(right-b4)# show port
===============================================================================
Ports on Slot 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
1/1/m1/1 Link Up anchor 100G
1/1/c1 Up Link Up conn 100GBASE-LR4*
1/1/c1/1 Up No Down 9212 9212 - netw null xgige
1/1/c1/2 Down No Down 9212 9212 - netw null xgige
1/1/c1/3 Down No Down 9212 9212 - netw null xgige
...
===============================================================================
Ports on Port Cross Connect 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
pxc-1.a Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-1.b Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-2.a Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-2.b Up Yes Link Up 1574 1574 - hybr dotq xgige
*A:ALU-1# show port 1/1
==============================================================================
Ports on Slot 1
==============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port SFP/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
------------------------------------------------------------------------------
1/1/1 Down No Down 1518 1518 1 accs dotq gige
1/1/2 Down No Down 1578 1578 - netw null gige
1/1/3 Down No Down 1578 1578 - netw null gige
1/1/4 Up No Down 1514 1514 - accs null gige
1/1/5 Up No Down 1578 1578 - netw null gige
==============================================================================
*A:ALU-1#
A:ALA-1# show port 1/1/6 associations
==============================================================================
Interface Table
==============================================================================
Router/ServiceId Name Encap Val
------------------------------------------------------------------------------
Router: Base if1000 1000
Router: Base if2000 2000
------------------------------------------------------------------------------
Interfaces
==============================================================================
A;ALA-1#
A:ALU-1# show port 5/1/4 detail
===============================================================================
Ethernet Interface
===============================================================================
Description : 10-Gig Ethernet
Interface : 5/1/4 Oper Speed : 10 Gbps
Link-level : Ethernet Config Speed : N/A
Admin State : up Oper Duplex : full
Oper State : down Config Duplex : N/A
Physical Link : No MTU : 9212
Single Fiber Mode : No Min Frame Length : 64 Bytes
IfIndex : 170000384 Hold time up : 0 seconds
Last State Change : 04/28/2017 13:09:15 Hold time down : 0 seconds
Hold Time Down Rmng: 0 cs Hold Time Up Rmng: 0 cs
Last Cleared Time : N/A DDM Events : Enabled
Phys State Chng Cnt: 10 RS-FEC Mode : None
Configured Mode : network Encap Type : null
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Ing. Pool Policy : n/a
Egr. Pool Policy : n/a
Net. Egr. Queue Pol: default
Egr. Sched. Pol : n/a
HS Scheduler Plcy : default
HS Port Pool Plcy : default
Monitor Port Sched : Disabled
Monitor Agg Q Stats: Disabled
Auto-negotiate : N/A MDI/MDX : N/A
Oper Phy-tx-clock : not-applicable
Accounting Policy : None Collect-stats : Disabled
Acct Plcy Eth Phys : None Collect Eth Phys : Disabled
Egress Rate : Default Ingress Rate : Default
Oper Egress Rate : unrestricted
Load-balance-algo : Default LACP Tunnel : Disabled
Access Bandwidth : Not-Applicable Booking Factor : 100
Access Available BW: 0
Access Booked BW : 0
Sflow : Disabled
Dampening State : Active Current Penalties: 2297
Suppress Threshold : 1500 Reuse Threshold : 1000
Max Penalties : 4000 Max Suppress Time: 40 seconds
Half Life : 20 seconds
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Sync. Status Msg. : Disabled Rx Quality Level : N/A
Tx DUS/DNU : Disabled Tx Quality Level : N/A
SSM Code Type : sdh ESMC Tunnel : Disabled
PTP TS Capability : ethernet
Down On Int. Error : Disabled DOIE Tx Disable : Disabled
CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds
CRC Mon SF Thresh : Disabled
Sym Mon SD Thresh : Disabled Sym Mon Window : 10 seconds
Sym Mon SF Thresh : Disabled Tot Sym Mon Errs : 0
EFM OAM : Disabled EFM OAM Link Mon : Disabled
Ignr EFM OAM State : False
Configured Address : 10:e8:78:4d:24:f0
Hardware Address : 10:e8:78:4d:24:f0
Cfg Alarm : remote local
Transceiver Data
Transceiver Status : operational
Transceiver Type : SFP
Model Number : 3HE04823AAAA01 ALA IPU3ANKEAA
TX Laser Wavelength: 1310 nm Diag Capable : yes
Connector Code : LC Vendor OUI : 00:90:65
Manufacture date : 2016/07/23 Media : Ethernet
Serial Number : AW40PC8
Part Number : FTLX1471D3BCL-A5
Optical Compliance : 10GBASE-LR
Link Length support: 10km for SMF
===============================================================================
Transceiver Digital Diagnostic Monitoring (DDM), Internally Calibrated
===============================================================================
Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +38.1 +78.0 +73.0 -8.0 -13.0
Supply Voltage (V) 3.31 3.70 3.60 3.00 2.90
Tx Bias Current (mA) 40.3 85.0 80.0 20.0 15.0
Tx Output Power (dBm) -1.29 2.00 1.00 -7.00 -8.00
Rx Optical Power (avg dBm) -1.38 2.50 2.00 -18.01 -20.00
===============================================================================
===============================================================================
===============================================================================
OTU Interface
===============================================================================
OTU Status : Disabled
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Utilization (300 seconds) 0.00% 0.00%
===============================================================================
Ethernet Statistics
===============================================================================
Broadcast Pckts : 0 Drop Events : 0
Multicast Pckts : 0 CRC/Align Errors : 0
Undersize Pckts : 0 Fragments : 0
Oversize Pckts : 0 Jabbers : 0
Collisions : 0
Octets : 0
Packets : 0
Packets of 64 Octets : 0
Packets of 65 to 127 Octets : 0
Packets of 128 to 255 Octets : 0
Packets of 256 to 511 Octets : 0
Packets of 512 to 1023 Octets : 0
Packets of 1024 to 1518 Octets : 0
Packets of 1519 or more Octets : 0
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 0 0
Multicast Packets 0 0
Broadcast Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
===============================================================================
Per Threshold MDA Discard Statistics
===============================================================================
Packets Octets
-------------------------------------------------------------------------------
Threshold 0 Dropped : 0 0
Threshold 1 Dropped : 0 0
Threshold 2 Dropped : 0 0
Threshold 3 Dropped : 0 0
Threshold 4 Dropped : 0 0
Threshold 5 Dropped : 0 0
Threshold 6 Dropped : 0 0
Threshold 7 Dropped : 0 0
Threshold 8 Dropped : 0 0
Threshold 9 Dropped : 0 0
Threshold 10 Dropped : 0 0
Threshold 11 Dropped : 0 0
Threshold 12 Dropped : 0 0
Threshold 13 Dropped : 0 0
Threshold 14 Dropped : 0 0
Threshold 15 Dropped : 0 0
===============================================================================
===============================================================================
Ingress Port Forwarding Engine Drop Reason Statistics
===============================================================================
IPv4 Header Error 0
IPv4 Invalid Address 0
IPv6 Header Error 0
IPv6 Invalid Address 0
IP Route Blackholed 0
ACL Filter Discards 0
Unicast RPF Check Failed 0
BFD Spoof Check Failed 0
Unicast MAC Destination Address Mismatch 0
Multicast MAC With Unicast Dest IP 0
Unknown MAC Destination Address Discarded in VPLS 0
L2 Service MTU Exceeded 0
Needs ICMP 0
===============================================================================
===============================================================================
Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 2 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 3 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 4 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 5 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 6 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 7 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 8 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 9 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 10 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 11 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 12 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 13 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 14 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 15 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 16 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Egress Queue 1 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 2 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 3 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 4 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 5 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 6 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 7 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 8 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
===============================================================================
B:Dut-A# show port 3/2/1
===============================================================================
...
===============================================================================
Adapter Data
Adapter Type : cfp-to-qsfp28
Model Number : 3HE13894AARA01
Vendor OUI : 00:00:00
Manufacture date : 2018/07/07
Serial Number : RS183000030002
Part Number : 3HE13894AARA01
A:Dut-C# show port 2/1/11 dot1x
===============================================================================
802.1x Port Status
===============================================================================
Port control : force-auth
Port status : authorized
Authenticator PAE state : force-auth
Backend state : idle
Reauth enabled : no Reauth period : N/A
Max auth requests : 2 Transmit period : 30
Supplicant timeout : 30 Server timeout : 30
Quiet period : 60
Radius-plcy : N/A
Tunneling : false
===============================================================================
802.1x Session Statistics
===============================================================================
authentication method : remote-radius
last session id : PAC-04258000-6E64D82E
last session time : 49213d04h
last session username : N/A
last session term cause : N/A
user tx octets : 1525626453326
user tx frames : 329677551
user rx octets : 1399995911442
user rx frames : 302536308
===============================================================================
Macsec
===============================================================================
Admin State : Up
eapol-destination-address :
Security Zone : 3
ca-name : dut_B_C_256_01
===============================================================================
*A:ALA-12>config# show port 1/1/1 ethernet
===============================================================================
Ethernet Interface
===============================================================================
Description : 1-Gig/10-Gig Ethernet
Interface : 1/1/1 Oper Speed : 10 Gbps
Link-level : Ethernet Config Speed : 10 Gbps
Admin State : down Oper Duplex : full
Oper State : down
Config Duplex : N/A
Physical Link : No MTU : 8704
Single Fiber Mode : No Min Frame Length : 64 Bytes
IfIndex : 35684352 Hold time up : 0 seconds
Last State Change : 06/09/2022 17:09:47 Hold time down : 0 seconds
Hold Time Down Rmng: 0 cs Hold Time Up Rmng: 0 cs
Last Cleared Time : N/A DDM Events : Enabled
Phys State Chng Cnt: 0
RS-FEC Config Mode : None
RS-FEC Oper Mode : None
Configured Mode : network Encap Type : null
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: default
Egr. Sched. Pol : n/a
DCPU Prot Policy : _default-port-policy
Oper DCPU Prot Plcy: _default-port-policy
Monitor Port Sched : Disabled
Monitor Agg Q Stats: Disabled
Monitor Oper Group : test
Auto-negotiate : N/A MDI/MDX : N/A
Oper Phy-tx-clock : not-applicable
Accounting Policy : None Collect-stats : Disabled
Acct Plcy Eth Phys : None Collect Eth Phys : Disabled
Egress Rate : Default Ingress Rate : Default
Oper Egress Rate : Unrestricted
Load-balance-algo : Default LACP Tunnel : Disabled
Access Bandwidth : Not-Applicable Booking Factor : 100
Access Available BW: 0
Access Booked BW : 0
Sflow : Disabled
Discard Rx Pause : Disabled
Suppress Threshold : 2000 Reuse Threshold : 1000
Max Penalties : 16000 Max Suppress Time: 20 seconds
Half Life : 5 seconds
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Sync. Status Msg. : Disabled Rx Quality Level : N/A
Tx DUS/DNU : Disabled Tx Quality Level : N/A
SSM Code Type : sdh ESMC Tunnel : Disabled
Down On Int. Error : Disabled DOIE Tx Disable : Disabled
CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds
CRC Mon SF Thresh : Disabled
Sym Mon SD Thresh : Disabled Sym Mon Window : 10 seconds
Sym Mon SF Thresh : Disabled Tot Sym Mon Errs : 0
EFM OAM : Disabled EFM OAM Link Mon : Disabled
Ignr EFM OAM State : False
Configured Address : b6:1b:01:01:00:01
Hardware Address : b6:1b:01:01:00:01
Cfg Alarm : remote local
Transceiver Data
Transceiver Status : operational
Transceiver Type : SFP DCO : Disabled
Model Number : 3HE04823AAAA01 ALA IPU3ANKEAA
TX Laser Wavelength: 1310 nm Diag Capable : yes
Connector Code : LC Vendor OUI : 00:90:65
Manufacture date : 2009/12/17 Media : Ethernet
Serial Number : UGR04DK
Part Number : FTLX1471D3BCL-A5
Optical Compliance : 10GBASE-LR
Link Length support: 10km for SMF
===============================================================================
Transceiver Digital Diagnostic Monitoring (DDM), Internally Calibrated
===============================================================================
Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +25.4 +78.0 +73.0 -8.0 -13.0
Supply Voltage (V) 3.31 3.70 3.60 3.00 2.90
Tx Bias Current (mA) 35.6 85.0 80.0 20.0 15.0
Tx Output Power (dBm) -1.46 2.00 1.00 -7.00 -8.00
Rx Optical Power (avg dBm) -2.18 2.50 2.00 -18.01 -20.00
===============================================================================
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Utilization (300 seconds) 0.00% 0.00%
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 0 0
Multicast Packets 0 0
Broadcast Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
show port 1/1/1 ethernet efm-oam
===============================================================================
Ethernet Oam (802.3ah)
===============================================================================
Admin State : down
Oper State : disabled
Mode : active
Pdu Size : 1518
Config Revision : 0
Function Support : LB
Transmit Interval : 1000 ms
Multiplier : 5
Hold Time : 0
Tunneling : false
Loop Detected : false
Grace Tx Enable : true (inactive)
Grace Vendor OUI : 00:16:4d
Dying Gasp on Reset: true (inactive)
Soft Reset Tx Act : none
Trigger Fault : none
Vendor OUI : 00:16:4d (alu)
Vendor Info : 00:01:00:02
No Peer Information Available
Loopback State : None
Loopback Ignore Rx : Ignore
Ignore Efm State : false
Link Monitoring : disabled
Peer RDI Rx
Critical Event : out-of-service
Dying Gasp : out-of-service
Link Fault : out-of-service
Event Notify : log-only
Local SF Action Discovery
Event Burst : 1 Ad Link Mon Cap : yes
Port Action : out-of-service
Dying Gasp : disabled
Critical Event : disabled
Errored Frame Errored Frame Period
Enabled : no Enabled : no
Event Notify : enabled Event Notify : enabled
SF Threshold : 1 SF Threshold : 1
SD Threshold : disabled (0) SD Threshold : disabled (0)
Window : 10 ds Window : 1488095 frames
Errored Symbol Period Errored Frame Seconds Summary
Enabled : no Enabled : no
Event Notify : enabled Event Notify : enabled
SF Threshold : 1 SF Threshold : 1
SD Threshold : disabled (0) SD Threshold : disabled (0)
Window (time) : 10 ds Window : 600 ds
Window (symbols) : 125000000
===============================================================================
Active Failure Ethernet OAM Event Logs
===============================================================================
Number of Logs : 0
===============================================================================
===============================================================================
Ethernet Oam Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Information 0 0
Loopback Control 0 0
Unique Event Notify 0 0
Duplicate Event Notify 0 0
Unsupported Codes 0 0
Frames Lost 0
===============================================================================
show port 1/2/1 ethernet efm-oam event-logs
==============================================================================
Active Failure Ethernet OAM Event Logs
===============================================================================
Log Index : 2
Event Time Reference : 10d 03:58:24
Location : remote
Type : Dying Gasp
Event Total : 1
Port Affecting : yes
-------------------------------------------------------------------------------
Number of Logs : 1
===============================================================================
===============================================================================
Active Degraded Ethernet OAM Event Logs
===============================================================================
Number of Logs : 0
===============================================================================
===============================================================================
Cleared Failure Ethernet OAM Event Logs
===============================================================================
Number of Logs : 0
===============================================================================
===============================================================================
Cleared Degraded Ethernet OAM Event Logs
===============================================================================
Number of Logs : 0
===============================================================================
show port 1/1/1 ethernet lldp remote-info detail
==============================================================================
Link Layer Discovery Protocol (LLDP) Port Information
==============================================================================
Port 1/1/1 Bridge nearest-bridge Remote Peer Information
-------------------------------------------------------------------------------
Remote Peer Index 9 at timestamp 12/08/2014 21:34:30:
Supported Caps : bridge router
Enabled Caps : bridge router
Chassis Id Subtype : 4 (macAddress)
Chassis Id : D8:1C:FF:00:00:00
PortId Subtype : 5 (interfaceName)
Port Id : 31:2F:32:2F:32
"1/2/2"
Port Description : n/a
System Name : cses-V28
System Description : TiMOS-B-0.0.I4269 both/i386 Nokia 7750 SR Copyright
(c) 2000-2016 Nokia.
All rights reserved. All use subject to applicable
license agreements.
Built on Wed Dec 3 19:14:27 PST 2014 by builder in /
rel0.0/I4269/panos/main
Remote Peer Index 9 management addresses at time 12/08/2014 21:34:30:
Address SubType : 1 (IPv4)
Address : 10.1.1.28
Address If SubType : 2 Address If Id : 1
Address OID : .1.3.6.1.4.1.6527.1.3.3
Port 1/1/1 Bridge nearest-non-tpmr Remote Peer Information
-------------------------------------------------------------------------------
No remote peers found
Port 1/1/1 Bridge nearest-customer Remote Peer Information
-------------------------------------------------------------------------------
No remote peers found
==============================================================================
show port 1/1/1 ethernet lldp detail
==============================================================================
Link Layer Discovery Protocol (LLDP) Port Information
==============================================================================
Port 1/1/1 Bridge nearest-bridge
-------------------------------------------------------------------------------
Admin State : txAndRx Notifications : Disabled
Tunnel Nearest Bridge : Disabled
Transmit TLVs : portDesc sysName sysDesc sysCap
PortID TLV Subtype : tx-if-name
Management Address Transmit Configuration:
Index 1 (system) : Enabled Address : 10.1.1.31
Index 2 (IPv6 system) : Disabled Address : ::
Port LLDP Stats:
Tx Frames : 11749 Tx Length Err Frames : 0
Rx Frames : 70399 Rx Frame Discard : 0
Rx Frame Errors : 0 Rx TLV Discard : 0
Rx TLV Unknown : 0 Rx Ageouts : 3
Port 1/1/1 Bridge nearest-non-tpmr
-------------------------------------------------------------------------------
Admin State : disabled Notifications : Disabled
Transmit TLVs : None
PortID TLV Subtype : tx-local
Management Address Transmit Configuration:
Index 1 (system) : Disabled Address : 10.1.1.31
Index 2 (IPv6 system) : Disabled Address : ::
Port LLDP Stats:
Tx Frames : 0 Tx Length Err Frames : 0
Rx Frames : 0 Rx Frame Discard : 0
Rx Frame Errors : 0 Rx TLV Discard : 0
Rx TLV Unknown : 0 Rx Ageouts : 0
Port 1/1/1 Bridge nearest-customer
-------------------------------------------------------------------------------
Admin State : disabled Notifications : Disabled
Transmit TLVs : None
PortID TLV Subtype : tx-local
Management Address Transmit Configuration:
Index 1 (system) : Disabled Address : 10.1.1.31
Index 2 (IPv6 system) : Disabled Address : ::
Port LLDP Stats:
Tx Frames : 0 Tx Length Err Frames : 0
Rx Frames : 0 Rx Frame Discard : 0
Rx Frame Errors : 0 Rx TLV Discard : 0
Rx TLV Unknown : 0 Rx Ageouts : 0
==============================================================================
# show port A/gnss
===============================================================================
GNSS Physical Interface
===============================================================================
Description : GNSS receiver
Interface : A/gnss Port IfIndex : 1611137290
Admin Status : up Oper Status : up
Physical Link : Yes
Constellation : gps
Ant. Cable Delay : 0 Elev. Mask Angle : 10
Antenna Status : ok Visible Satellites : 9
Sync Status : locked Used Satellites : 7
Receiver Status : Position Hold
Time : 2020/04/23 18:47:38 Latitude : +45.34811
UTC Offset : 17 Longitude : -75.92142
Firmware Version : 2.04.0 Altitude (m MSL) : 90
===============================================================================
*A:Dut-C# show port 2/1/11 macsec sub-port 1 statistics
===============================================================================
MACsec Statistics
===============================================================================
-------------------------------------------------------------------------------
txSecyStats
-------------------------------------------------------------------------------
Untagged Packets : 0
Too Long Packets : 0
-------------------------------------------------------------------------------
txSCSecyStats
-------------------------------------------------------------------------------
TxSc SCI PortNum : 1
Protected Packets : 0
Encrypted Packets : 0
Protected Octets : 0
Encrypted Octets : 0
-------------------------------------------------------------------------------
txSASecyStats
-------------------------------------------------------------------------------
AN : 0
Protected SA Packets : 0
Encrypted SA Packets : 0
AN : 1
Protected SA Packets : 0
Encrypted SA Packets : 0
AN : 2
Protected SA Packets : 0
Encrypted SA Packets : 0
AN : 3
Protected SA Packets : 0
Encrypted SA Packets : 0
-------------------------------------------------------------------------------
rxSecyStats
-------------------------------------------------------------------------------
No Tag Packets : 4681
Bad Tag Packets : 0
No SCI Packets : 0
Overrun Packets : 0
-------------------------------------------------------------------------------
rxSCSecyStats
-------------------------------------------------------------------------------
SCI : a47b2ce1110d0001
No Using SA Packets : 0
Late Packets : 0
Not Valid Packets : 0
Delayed Packets : 0
Unchecked Packets : 0
OK Packets : 0
Validated Octets : 0
Decrypted Octets : 0
-------------------------------------------------------------------------------
rxSASecyStats
-------------------------------------------------------------------------------
SCI : a47b2ce1110d0001
AN : 2
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 0
AN : 3
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 0
-------------------------------------------------------------------------------
rxSCSecyStats
-------------------------------------------------------------------------------
SCI : a47b2ce1128e0001
No Using SA Packets : 0
Late Packets : 0
Not Valid Packets : 0
Delayed Packets : 0
Unchecked Packets : 0
OK Packets : 0
Validated Octets : 0
Decrypted Octets : 0
-------------------------------------------------------------------------------
rxSASecyStats
-------------------------------------------------------------------------------
SCI : a47b2ce1128e0001
AN : 0
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 0
AN : 1
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 0
AN : 2
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 0
AN : 3
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 0
===============================================================================
A:Dut-C# show port 2/1/11 macsec statistics
===============================================================================
MACsec Statistics
===============================================================================
-------------------------------------------------------------------------------
txSecyStats
-------------------------------------------------------------------------------
Untagged Packets : 0
Too Long Packets : 0
-------------------------------------------------------------------------------
rxSecyStats
-------------------------------------------------------------------------------
No Tag Packets : 758
Bad Tag Packets : 0
No SCI Packets : 0
Overrun Packets : 0
-------------------------------------------------------------------------------
txSCSecyStats
-------------------------------------------------------------------------------
Protected Packets : 0
Encrypted Packets : 355170025
Protected Octets : 0
Encrypted Octets : 1637917300250
-------------------------------------------------------------------------------
rxSCSecyStats
-------------------------------------------------------------------------------
SCI : 00:00:a4:7b:2c:e1
No Using SA Packets : 0
Late Packets : 0
Not Valid Packets : 0
Delayed Packets : 0
Unchecked Packets : 0
OK Packets : 325904694
Validated Octets : 0
Decrypted Octets : 1502922287478
-------------------------------------------------------------------------------
txSASecyStats
-------------------------------------------------------------------------------
AN : 0
Protected SA Packets : 0
Encrypted SA Packets : 355170201
-------------------------------------------------------------------------------
rxSASecyStats
-------------------------------------------------------------------------------
SCI : 00:00:a4:7b:2c:e1
AN : 0
No Using SA Packets : 0
Not Valid Packets : 0
OK Packets : 325904947
===============================================================================
In the "Coherent Optical Module” section of the output example, the configurable Tx Pwr values are only shown if the module supports this option.
*A:ALU-1# show port 4/1/1 optical detail
===============================================================================
Optical Interface
===============================================================================
Transceiver Data
Transceiver Status : operational
Transceiver Type : MSA-100GLH
Model Number : 28-0089-XX
TX Laser Wavelength: 1558.172 nm
TX Laser Frequency : 192.400 THz
Laser Tunability : fully-tunable
Config Freq (MHz) : 195300000 Min Freq (MHz) : 191300000
Oper Freq (MHz) : 195300000 Max Freq (MHz) : 196100000
Fine Tune Range : 6000 MHz Fine Tune Resolution : 1 MHz
Supported Grids : 100GHz 75GHz 50GHz 25GHz 12.5GHz 6.25GHz
Diag Capable : yes
Number of Lanes : 1
Connector Code : LC Vendor OUI : 00:03:fa
Manufacture date : 2012/07/16 Media : Ethernet
Serial Number : 122900645
Part Number : AC100-201-00E
Optical Compliance : DWDM-TUN
Link Length support: 80km for SMF
===============================================================================
Transceiver Digital Diagnostic Monitoring (DDM)
===============================================================================
Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +60.9 +80.0 +70.0 +0.0 -5.0
Supply Voltage (V) 12.07 13.00 12.60 11.40 11.00
===============================================================================
===============================================================================
Transceiver Lane Digital Diagnostic Monitoring (DDM)
===============================================================================
High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Lane Temperature (C) +75.0 +70.0 +20.0 +15.0
Lane Tx Bias Current (mA) 10.0 9.0 3.0 2.0
Lane Tx Output Power (dBm) 3.00 2.00 0.00 -1.00
Lane Rx Optical Pwr (avg dBm) 8.16 5.00 -20.00 -23.01
-------------------------------------------------------------------------------
Lane ID Temp(C)/Alm Tx Bias(mA)/Alm Tx Pwr(dBm)/Alm Rx Pwr(dBm)/Alm
-------------------------------------------------------------------------------
1 +48.4 5.1 0.99 -10.45
===============================================================================
===============================================================================
Coherent Optical Module
===============================================================================
Cfg Tx Target Power: 1.00 dBm
Cfg Rx LOS Thresh : -23.00 dBm
Disp Control Mode : automatic Sweep Start Disp : -25500 ps/nm
Cfg Dispersion : 0 ps/nm Sweep End Disp : 2000 ps/nm
CPR Window Size : 4 symbols
Cfg Tx Pwr Minimum : -22.90 dBm
Cfg Tx Pwr Maximum : 4.00 dBm
Cfg Alarms : modflt mod netrx nettx hosttx
Alarm Status :
Defect Points :
Rx Q Margin : 10.1 dB Chromatic Disp : 1 ps/nm
SNR X Polar : 19.7 dB Diff Group Delay : 0 ps
SNR Y Polar : 19.8 dB Pre-FEC BER : 0.000E+00
Module State : ready
Tx Turn-Up States : init laserTurnUp laserReadyOff laserReady
modulatorConverge outputPowerAdjust
Rx Turn-Up States : init laserReady waitForInput adcSignal opticalLock
demodLock
===============================================================================
-------------------------------------------------------------------------------
Coherent Optical Port Statistics (Elapsed Seconds: 1281709)
-------------------------------------------------------------------------------
Statistic Current Average Minimum Maximum
-------------------------------------------------------------------------------
Rx BER 9.060E-04 2.500E-01 0.000E+00 5.000E-01
Rx SNR (dB) 17.9 9.0 0.0 18.0
Rx OSNR (dB) 29.5 15.0 0.0 30.1
Rx Chromatic Disp (ps/nm) 2050 1027 0 2054
Rx Diff Group Delay (ps) 1 1 0 2
Rx Freq Offset (MHz) 108 90 -42 223
Rx Q (dB) 9.8 4.9 0.0 9.9
Rx Signal Power (dBm) -0.04 -2.57 -99.00 0.44
Tx Total Power (dBm) -11.88 -3.01 -99.00 0.00
Rx Total Power (dbm) -11.88 -3.01 -99.00 0.00
Polar Depend Loss (dB) 0.6 0.6 0.5 0.7
State of polar ROC (krad/s) 0 65535 65535 0
Rx Media Frame Error Count 122 65535 65535 0
-------------------------------------------------------------------------------
show port 1/1/c2
===============================================================================
QSFP-DD Connector
===============================================================================
Description : QSFP-DD Connector
Interface : 1/1/c2
Admin State : up
Oper State : up
IfIndex : 1610899584
Last State Change : 09/28/2023 16:43:14
Last Cleared Time : N/A DDM Events : Enabled
Breakout : no breakout
RS-FEC Config Mode : None
Transceiver Data
Transceiver Status : unsupported
Transceiver Type : QSFP28 DCO : Disabled
OLS : Enabled OLS Egr Amp Gain : 22.00 dB
Model Number : none
TX Laser Wavelength: 1550 nm Diag Capable : yes
Number of Lanes : 2
Connector Code : CS Vendor OUI : 00:1c:73
Manufacture date : 2022/10/21 Media : Ethernet
Serial Number : P20600032
Part Number : QSFP-AMP-ZR
Optical Compliance : QSFP-AMP-ZR
Link Length support: 100km for SMF
===============================================================================
Transceiver Digital Diagnostic Monitoring (DDM)
===============================================================================
Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +33.1 +70.0 +65.0 +0.0 -5.0
Supply Voltage (V) 3.29 3.46 3.40 3.20 3.13
===============================================================================
===============================================================================
Transceiver Lane Digital Diagnostic Monitoring (DDM)
===============================================================================
High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Pump Temperature (C) +75.0 +70.0 +5.0 +0.0
Amplifier Gain (dB) 25.50 25.10 0.00 0.00
Amplifier Output Power (dBm) 17.10 17.00 0.00 -6.04
Amplifier Input Power (dBm) 14.80 13.80 -22.52 -26.20
-------------------------------------------------------------------------------
Amp ID Pump Temp(C)/Alm Gain (dB)/Alm Out Pwr(dBm)/Alm In Pwr(dBm)/Alm
-------------------------------------------------------------------------------
EgrAmp +33.6 22.00 1.35 -21.94
IngAmp +33.5 20.30 2.80 -18.18
===============================================================================
===============================================================================
A:ALA-49>config>port# show port 3/2/1 otu detail
===============================================================================
OTU Interface
===============================================================================
OTU Status : Enabled FEC Mode : enhanced
Data Rate : 11.049 Gb/s
Cfg Alarms : loc los lof lom otu-ber-sf otu-bdi fec-sf
Alarm Status :
SF/SD Method : FEC SF Threshold : 1E-5
SD Threshold : 1E-7
SM-TTI Tx (auto) : ALA-49:3/2/1/C17
SM-TTI Rx : (Not Specified)
===============================================================================
OTU Statistics
===============================================================================
Statistics Count
-------------------------------------------------------------------------------
FEC Corrected 0s 0
FEC Corrected 1s 0
FEC Unrrectable Sub-rows 0
FEC SES 0
SM BIP8 0
SM BEI 0
SM SES 0
PM BIP8 0
PM BEI 0
PM SES 0
===============================================================================
*A:PE1# show port 5/1/5 port-scheduler statistics
===============================================================================
Port 5/1/5 Port Scheduler
===============================================================================
Policy-Name : esp1
Description : (Not Specified)
Last Cleared Time : 11/16/2018 15:30:10
Packets Octets
Forwarded: 211912 27124736
Dropped* : 853335 109226880
-------------------------------------------------------------------------------
Port Scheduler per Level Queueing Statistics
Packets Octets
Level : 8
Forwarded: 0 0
Dropped* : 0 0
Level : 7
Forwarded: 0 0
Dropped* : 0 0
Level : 6
Forwarded: 0 0
Dropped* : 0 0
Level : 5
Forwarded: 0 0
Dropped* : 0 0
Level : 4
Forwarded: 0 0
Dropped* : 0 0
Level : 3
Forwarded: 0 0
Dropped* : 0 0
Level : 2
Forwarded: 84784 10852352
Dropped* : 270297 34598016
Level : 1
Forwarded: 127128 16272384
Dropped* : 583038 74628864
-------------------------------------------------------------------------------
* indicates that the policer drop statistics are not included if HQoS policers
are managed by the scheduler.
===============================================================================
# show port port-queues queue-depth queue 5
===============================================================================
Queue Depth Information (Port-based Network Egress)
===============================================================================
-------------------------------------------------------------------------------
Name : Queue: 5 Port=1/1/1
MBS : Def
Violation Threshold Percnt: xx.xx
Violation Total Count : xxx
Violation Last Seen : Thu Mar 26 12:39:33 PDT 2020
-------------------------------------------------------------------------------
Queue Depths (percentage)
-------------------------------------------------------------------------------
0%-10% 11%-20% 21%-30% 31%-40% 41%-50% 51%-60% 61%-70% 71%-80% 81%-90% 91%-100%
-------------------------------------------------------------------------------
100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
-------------------------------------------------------------------------------
Average Elapsed Time : 0d 00:11:11
Wghtd Avg Queue Poll Interval : 100 ms
Wghtd Avg HiWtrMark Poll Interval: 1000 ms
-------------------------------------------------------------------------------
===============================================================================
*A:PE# show port 5/1/1 queue-group ingress
===============================================================================
Ethernet Port 5/1/1 Access Ingress Queue-Group
===============================================================================
Group Name : qg1
Description : (Not Specified)
Sched Policy : None Acct Pol : None
Collect Stats : disabled
Queues
-------------------------------------------------------------------------------
Ing. QGroup : qg1 Queue-Id : 1 (Unicast) (Priority)
Description : (Not Specified)
Admin PIR : max* Admin CIR : 0*
PIR Rule : closest* CIR Rule : closest*
Admin FIR : 0* FIR Rule : closest*
CBS : def* MBS : def*
Monitor Depth : not-applicable
Low Drop Tail : def*
* means the value is inherited
===============================================================================
===============================================================================
*A:PE#
*A:PE# show port 5/1/1 queue-group egress
===============================================================================
Ethernet port 5/1/1 Access Egress queue-group
===============================================================================
Group Name : qg1 Instance-Id : 1
Description : (Not Specified)
Sched Policy : None Acct Pol : None
Collect Stats : disabled Agg. Limit : max
Limit Unused BW : Disabled
Frame Based Acc : Disabled
HS Turbo Queues : Disabled
Queues
-------------------------------------------------------------------------------
Queue-Group : qg1 Instance-Id : 1 Queue-Id : 1
Description : (Not Specified)
Admin PIR : 50000* Admin CIR : 0*
PIR Rule : closest* CIR Rule : closest*
CBS : def* MBS : 1000 KB*
Weight : not-applicable CIR Weight : not-applicable
Monitor Depth : not-applicable
HiPlus Drop Tail : def* Hi Drop Tail : def*
Low Drop Tail : def* Exceed Drop *: def*
* means the value is inherited
===============================================================================
Host-Matches
-------------------------------------------------------------------------------
No Host-Matches found
-------------------------------------------------------------------------------
Group Name : policer-output-qu* Instance-Id : 1
Description : (Not Specified)
Sched Policy : None Acct Pol : None
Collect Stats : disabled Agg. Limit : max
Limit Unused BW : Disabled
Frame Based Acc : Disabled
HS Turbo Queues : Disabled
Queues
-------------------------------------------------------------------------------
Queue-Group : policer-output-qu* Instance-Id : 1 Queue-Id : 1
Description : Default egress policer output queues.
Admin PIR : max* Admin CIR : 0*
PIR Rule : closest* CIR Rule : closest*
CBS : def* MBS : def*
Weight : not-applicable CIR Weight : not-applicable
Monitor Depth : not-applicable
HiPlus Drop Tail : def* Hi Drop Tail : def*
Low Drop Tail : def* Exceed Drop *: def*
Queue-Group : policer-output-qu* Instance-Id : 1 Queue-Id : 2
Description : Default egress policer output queues.
Admin PIR : max* Admin CIR : 0*
PIR Rule : closest* CIR Rule : closest*
CBS : def* MBS : def*
Weight : not-applicable CIR Weight : not-applicable
Monitor Depth : not-applicable
HiPlus Drop Tail : def* Hi Drop Tail : def*
Low Drop Tail : def* Exceed Drop *: def*
* means the value is inherited
===============================================================================
Host-Matches
-------------------------------------------------------------------------------
No Host-Matches found
-------------------------------------------------------------------------------
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:PE#
*A:PE# show port 5/1/1 queue-group summary
===============================================================================
Port queue-group summary
===============================================================================
Access-egress queue groups:
----------------------------
qg1
policer-output-queues
Total number of access-egress queue groups : 2
Network-egress queue groups:
----------------------------
Total number of network-egress queue groups : 0
Access-ingress queue groups:
----------------------------
qg1
Total number of access-ingress queue groups : 1
===============================================================================
*A:PE#
A:ALA-48# show port 1/2/1.sts192 detail
============================================================================
WAN Interface Sublayer Path Info
============================================================================
Oper Status : up
Signal Label : 0x1a Rx Signal Label : 0x1a
Trace String : Nokia 7750 SR
Rx Trace Str(Hex) : 89 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Cfg Alarm : pais plop prdi pplm prei puneq plcd
Alarm Status :
============================================================================
Sonet Path
============================================================================
Far End
-------------------------------------------
ES-P 1 0
SES-P 1 0
UAS-P 0 0
CV-P 10 0
============================================================================
============================================================================
Transmit:
LOP-P : 0
Fifo Error : 96
Max Packet Error : 0
Min Packet Error : 0
LLP Packet Error : 0
FIFO Underflow Error : 0
Receive:
LOP-P : 0
AIS-P : 1
RDI-P : 0
PLM-P : 0
LCD-P : 0
Unequipped : 0
Remote Error : 6
Parity Error : 10
Fifo Error : 0
Max Pkt Error : 0
Min Pkt Error : 0
FCS Error : 0
Packet Abort Error : 0
Addr Ctrl Invalid : 0
============================================================================
Port Statistics
============================================================================
Input
Output
----------------------------------------------------------------------------
Unicast Packets 369758853
5312
Multicast Packets 0
0
Broadcast Packets 0
0
Discards 0
0
Unknown Proto Discards 0
============================================================================
A:ALA-48#
A:ALA-7# show port 7/1/1.ds0grp-1.1
================================================================================
TDM DS0 Chan Group
================================================================================
Description : DS3
Interface : 7/1/1.ds0grp-1.1
TimeSlots : 1
Speed : 64 CRC : 16
Admin Status : up Oper status : down
Last State Change : 2007/04/11 01:14:37 Chan-Grp IfIndex : 656441433
Configured mode : access Encap Type : bcp-null
Admin MTU : 1522 Oper MTU : 1522
Physical Link : No
================================================================================
Port Statistics
=======================================================================
Input Output
-----------------------------------------------------------------------
Unicast Packets 0 0
Multicast Packets 0 0
Broadcast Packets 0 0
Discards 0 0
Unknown Proto Discards 0
=======================================================================
A:ALA-7#
A:ALA-48# show port 3/1/3.e3
===============================================================================
TDM Interface
===============================================================================
Description : E3
Interface : 3/1/3.e3
Type : e3 Framing : g751
Admin Status : up Oper status : down
Physical Link : No Clock Source : loop-timed
Last State Change : 04/11/2007 06:54:28 Port IfIndex : 589398019
Configured mode : access Encap Type : bcp-null
Admin MTU : 1518 Oper MTU : 1518
CRC : 16 Channelized : none
Idle Cycle Flags : flags Loopback : none
FEAC Loop Respond : Disabled In FEAC Loop : No
BERT Pattern : none BERT Duration : N/A
===============================================================================
A:ALA-48#
The output displays the aggregate egress queue statistics for ports configured with monitor-agg-egress-queue-stats which have non-zero counters. This can be shown for a single port, or all ports on an MDA or card. When the detail parameter is added, the output includes those ports with counters that are all zero.
*A:PE# show port 2 statistics egress-aggregate detail
===============================================================================
Port 2/1/1 Egress Aggregate Statistics on Slot 2
===============================================================================
Forwarded Dropped Total
-------------------------------------------------------------------------------
PacketsIn 303 0 303
PacketsOut 0 0 0
OctetsIn 25996 0 25996
OctetsOut 0 0 0
===============================================================================
===============================================================================
Port 2/1/2 Egress Aggregate Statistics on Slot 2
===============================================================================
Forwarded Dropped Total
-------------------------------------------------------------------------------
PacketsIn 140 0 140
PacketsOut 0 0 0
OctetsIn 9598 0 9598
OctetsOut 0 0 0
===============================================================================
*A:Dut-A# show port 1/1/2 vport "vp1"
========================================================================
Ethernet port 1/1/2 Access Egress vport
========================================================================
VPort Name : vp1
Description : (Not Specified)
Sched Policy : psp
Host-Matches
------------------------------------------------------------------------
Dest: dslam1
------------------------------------------------------------------------
========================================================================
*A:Dut-A#
*A:Dut-A# show port 1/1/2 vport "vp1" associations
========================================================================
Ethernet port 1/1/2 Access Egress vport
========================================================================
------------------------------------------------------------------------
VPort "vp1"
------------------------------------------------------------------------
svc-id : 1
sap : 1/1/2:1
subscr: s1
ip : 10.1.1.2
mac : 00:00:00:00:00:01 pppoe-sid: N/A
========================================================================
*A:Dut-A
*A:Dut-A# show port 1/1/1 vport "abc" monitor-threshold
===============================================================================
Port 1/1/1 Vport "abc" Monitor Threshold Info
===============================================================================
Attribute Exceed Count Config Rate Threshold Prcnt
-------------------------------------------------------------------------------
Agg-Eps 0 212 32
Lvl-1 0 12323 89
Lvl-2 0 32132 32
Lvl-5 0 2323 4
Grp-01234567890123458746513513355656 0 2121 12
-------------------------------------------------------------------------------
Start Time : 01/07/2015 16:53:16 End Time : 01/07/2015 16:53:36
Total Samples :
===============================================================================
*A:Dut-A
If the Vport name is omitted, statistics for all Vports are displayed (bulk read). The statistics are displayed only for the levels, groups, and agg-eps for which the monitor-threshold is enabled. The output information filtering per level, group, or agg-eps is not embedded in the show commands natively. Instead, the output can be filtered with the match extensions for the show command. For example, show port 1/1/1 vport test monitor-threshold | match Lvl-1.
*A:sne# show port 1/1/4 vport statistics
===============================================================================
Port 1/1/4 Access Egress vport
===============================================================================
VPort Name : vp1
Description : (Not Specified)
Sched Policy : portschedpol1
Rate Limit : Max
Rate Modify : disabled
Modify delta : 0
Vport Queueing Statistics
Last Cleared Time : N/A
Packets Octets
Forwarded: 0 0
Dropped : 0 0
-------------------------------------------------------------------------------
Vport per Level Queueing Statistics
Packets Octets
Level : 8
Forwarded: 0 0
Dropped : 0 0
Level : 7
Forwarded: 0 0
Dropped : 0 0
Level : 6
Forwarded: 0 0
Dropped : 0 0
Level : 5
Forwarded: 0 0
Dropped : 0 0
Level : 4
Forwarded: 0 0
Dropped : 0 0
Level : 3
Forwarded: 0 0
Dropped : 0 0
Level : 2
Forwarded: 0 0
Dropped : 0 0
Level : 1
Forwarded: 0 0
Dropped : 0 0
Host-Matches
-------------------------------------------------------------------------------
Dest: dslam1
-------------------------------------------------------------------------------
===============================================================================
*A:sne#
*A:cses-V22# show port
===============================================================================
Ports on Slot 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
1/1/1 Down Yes Up 8704 8704 - netw null xcme GIGE-LX 10KM
1/1/2 Up Yes Up 1514 1514 - accs null xcme GIGE-LX 10KM
1/1/3 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/4 Up Yes Up 1514 1514 - accs null xcme GIGE-LX 10KM
1/1/5 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/6 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/7 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/8 Up Yes Up 8704 8704 - hybr dotq xcme GIGE-LX 10KM
1/1/9 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/10 Down Yes Down 8704 8704 - netw null xcme GIGE-LX 10KM
A:admin@mci(right-b4)# show port
===============================================================================
Ports on Slot 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
1/1/m1/1 Link Up anchor 100G
1/1/c1 Up Link Up conn 100GBASE-LR4*
1/1/c1/1 Up No Down 9212 9212 - netw null xgige
1/1/c1/2 Down No Down 9212 9212 - netw null xgige
1/1/c1/3 Down No Down 9212 9212 - netw null xgige
...
===============================================================================
Ports on Port Cross Connect 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
pxc-1.a Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-1.b Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-2.a Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-2.b Up Yes Link Up 1574 1574 - hybr dotq xgige
Output Example: show port detail for a satellite uplink port
show port esat-1/1/c5/u1 detail
===============================================================================
Ethernet Interface
===============================================================================
Description : 400-Gig Ethernet
Interface : esat-1/1/c5/u1 Oper Speed : 400 Gbps
Link-level : Ethernet Config Speed : N/A
Admin State : up Oper Duplex : full
Oper State : up
Config Duplex : N/A
Physical Link : Yes MTU : 9212
Single Fiber Mode : No Min Frame Length : 64 Bytes
IfIndex : 1140966017 Hold time up : 0 seconds
Last State Change : 09/30/2023 07:42:28 Hold time down : 0 seconds
Hold Time Down Rmng: 0 cs Hold Time Up Rmng: 0 cs
Last Cleared Time : N/A
Phys State Chng Cnt: 55
RS-FEC Config Mode : None
RS-FEC Oper Mode : cl119
Far-end port ID : 1/x1/1/c2/1
Configured Mode : access Encap Type : 802.1q
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: n/a
Egr. Sched. Pol : n/a
HwAggShaper Sch Pol: n/a
Monitor Port Sched : Disabled
Monitor Agg Q Stats: Disabled
Monitor Oper Group : none
Monitor HwAggShap *: Disabled
Auto-negotiate : N/A MDI/MDX : N/A
Oper Phy-tx-clock : not-applicable
Accounting Policy : None Collect-stats : Disabled
Acct Plcy Eth Phys : None Collect Eth Phys : Disabled
Egress Rate : Default Ingress Rate : Default
Oper Egress Rate : Unrestricted
Load-balance-algo : Default LACP Tunnel : Disabled
Access Bandwidth : Not-Applicable Booking Factor : 100
Access Available BW: 0
Access Booked BW : 0
Sflow : Disabled
Discard Rx Pause : Disabled
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Sync. Status Msg. : Disabled Rx Quality Level : N/A
Tx DUS/DNU : Disabled Tx Quality Level : N/A
SSM Code Type : sdh ESMC Tunnel : Disabled
PTP TS Capability :
CRC Mon SD Thresh : 6*10E-7 CRC Mon Window : 10 seconds
CRC Mon SF Thresh : 4*10E-5
EFM OAM : Disabled EFM OAM Link Mon : Disabled
Ignr EFM OAM State : False
Configured Address : e4:41:64:7b:42:27
Hardware Address : e4:41:64:7b:42:27
Cfg Alarm : remote local
----------------------------------------------------------------------
Ethernet Bandwidth Notification Message Information
----------------------------------------------------------------------
ETH-BN Egr Rate Changes: Disabled
ETH-BN Rate (kbps) : None
----------------------------------------------------------------------
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 12287868837323 12276482441319
Packets 29574258275 29537765516
Errors 0 0
===============================================================================
Ethernet Statistics
===============================================================================
Broadcast Pckts : 1235438977 Drop Events : 0
Multicast Pckts : 3667667411 CRC/Align Errors : 0
Undersize Pckts : 0 Fragments : 0
Oversize Pckts : 0 Jabbers : 0
Collisions : 0
Octets : 24564351278642
Packets : 59112023791
Packets of 64 Octets : 19931
Packets of 65 to 127 Octets : 49484559475
Packets of 128 to 255 Octets : 3035408192
Packets of 256 to 511 Octets : 1661149068
Packets of 512 to 1023 Octets : 1094762996
Packets of 1024 to 1518 Octets : 668024442
Packets of 1519 or more Octets : 3168099687
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 27115598668 27093318735
Multicast Packets 1838494691 1829172720
Broadcast Packets 620164916 615274061
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
===============================================================================
Sat Port Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Sat Egress Queue 1 Packets Octets
Fwd Stats : 8257120707 4112066787804
Drop Stats : 0 0
Sat Egress Queue 2 Packets Octets
Fwd Stats : 317138867 21905134529
Drop Stats : 0 0
Sat Egress Queue 3 Packets Octets
Fwd Stats : 312021096 22007488810
Drop Stats : 0 0
Sat Egress Queue 4 Packets Octets
Fwd Stats : 14673309206 998842948449
Drop Stats : 0 0
Sat Egress Queue 5 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 6 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 7 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 8 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
===============================================================================
Output Example: show port detail for a satellite client port
show port esat-1/1/c2/4 detail
===============================================================================
Ethernet Interface
===============================================================================
Description : 25-Gig Ethernet
Interface : esat-1/1/c2/4 Oper Speed : 25 Gbps
Link-level : Ethernet Config Speed : N/A
Admin State : down Oper Duplex : full
Oper State : down
Config Duplex : N/A
Physical Link : No MTU : 9208
Single Fiber Mode : No Min Frame Length : 64 Bytes
IfIndex : 1140932868 Hold time up : 0 seconds
Last State Change : 09/30/2023 07:41:51 Hold time down : 0 seconds
Hold Time Down Rmng: 0 cs Hold Time Up Rmng: 0 cs
Last Cleared Time : N/A
Phys State Chng Cnt: 0
RS-FEC Config Mode : None
RS-FEC Oper Mode : None
Configured Mode : network Encap Type : null
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: default
Egr. Sched. Pol : n/a
DCPU Prot Policy : _default-port-policy
Oper DCPU Prot Plcy: _default-port-policy
HwAggShaper Sch Pol: n/a
Monitor Port Sched : Disabled
Monitor Agg Q Stats: Disabled
Monitor Oper Group : none
Monitor HwAggShap *: Disabled
Auto-negotiate : N/A MDI/MDX : N/A
Oper Phy-tx-clock : not-applicable
Accounting Policy : None Collect-stats : Disabled
Acct Plcy Eth Phys : None Collect Eth Phys : Disabled
Egress Rate : Default Ingress Rate : Default
Oper Egress Rate : Unrestricted
Load-balance-algo : Default LACP Tunnel : Disabled
Access Bandwidth : Not-Applicable Booking Factor : 100
Access Available BW: 0
Access Booked BW : 0
Sflow : Disabled
Discard Rx Pause : Disabled
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Sync. Status Msg. : Disabled Rx Quality Level : N/A
Tx DUS/DNU : Disabled Tx Quality Level : N/A
SSM Code Type : sdh ESMC Tunnel : Disabled
PTP TS Capability :
CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds
CRC Mon SF Thresh : Disabled
EFM OAM : Disabled EFM OAM Link Mon : Disabled
Ignr EFM OAM State : False
Configured Address : e4:41:64:7b:42:12
Hardware Address : e4:41:64:7b:42:12
Cfg Alarm : remote local
Alarm Status : local
Reported Alarms : local
----------------------------------------------------------------------
Ethernet Bandwidth Notification Message Information
----------------------------------------------------------------------
ETH-BN Egr Rate Changes: Disabled
ETH-BN Rate (kbps) : None
----------------------------------------------------------------------
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 735804410152 735804410344
Packets 5454727392 5454727395
Errors 0 0
===============================================================================
Ethernet Statistics
===============================================================================
Broadcast Pckts : 3 Drop Events : 0
Multicast Pckts : 0 CRC/Align Errors : 0
Undersize Pckts : 0 Fragments : 0
Oversize Pckts : 0 Jabbers : 0
Collisions : 0
Octets : 1471608820496
Packets : 10909454787
Packets of 64 Octets : 2333235065
Packets of 65 to 127 Octets : 8495213712
Packets of 128 to 255 Octets : 0
Packets of 256 to 511 Octets : 0
Packets of 512 to 1023 Octets : 0
Packets of 1024 to 1518 Octets : 0
Packets of 1519 or more Octets : 81006010
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 5454727392 5454727392
Multicast Packets 0 0
Broadcast Packets 0 3
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
===============================================================================
Ingress Port Forwarding Engine Drop Reason Statistics
===============================================================================
IPv4 Header Error 0
IPv4 Invalid Address 0
IPv6 Header Error 0
IPv6 Invalid Address 0
IP Route Blackholed 0
ACL Filter Discards 0
Unicast RPF Check Failed 0
BFD Spoof Check Failed 0
Unicast MAC Destination Address Mismatch 0
Multicast MAC With Unicast Dest IP 0
Unknown MAC Destination Address Discarded in VPLS 0
L2 Service MTU Exceeded 0
Needs ICMP 0
===============================================================================
===============================================================================
Sat Port Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Sat Egress Queue 1 Packets Octets
Fwd Stats : 5454727392 757623319720
Drop Stats : 0 0
Sat Egress Queue 2 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 3 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 4 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 5 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 6 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 7 Packets Octets
Fwd Stats : 0 0
Drop Stats : 0 0
Sat Egress Queue 8 Packets Octets
Fwd Stats : 3 204
Drop Stats : 0 0
===============================================================================
===============================================================================
Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 2 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 3 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 4 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 5 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 6 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 7 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 8 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 9 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 10 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 11 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 12 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 13 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 14 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 15 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 16 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Egress Queue 1 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 2 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 3 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 4 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 5 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 6 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 7 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
Egress Queue 8 Packets Octets
In/Inplus Prof fwded : 0 0
In/Inplus Prof dropped: 0 0
Out/Exc Prof fwded : 0 0
Out/Exc Prof dropped : 0 0
===============================================================================
Output Fields: show port <port-id> describes the output fields for the show port <port-id> command.
|
Label |
Description |
|---|---|
|
50GHz Ch Min/Max |
The 50 GHz channel minimum and maximum |
|
100GHz Ch Min/Max |
The 100 GHz channel minimum and maximum |
|
Acct Pol |
The accounting policy for the egress queue-group |
|
ACL Filter Discards |
The packet was dropped by a filter (ACL) on the line card (such as IP or MAC filter). Packets dropped by CPM filters or ESM anti-spoof filters do not increment this counter. |
|
Active Pre-Shared Key CKN |
The active PSK CAK name |
|
Active Pre-Shared Key Index |
The active pre-shared key index: 1 to 2 (default 1) |
|
Adapter Type |
The type of adapter module |
|
Addr Ctrl Invalid |
The number of invalid address control received |
|
Address |
The IP address associated with the index |
|
Admin CIR |
The administrative Committed Information Rate (CIR) parameters for the queue. The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. |
|
Admin FIR |
The admin queue FIR rate |
|
Admin PIR |
The administrative Peak Information Rate (PIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the switch fabricor out an egress interface. |
|
Admin State |
Up — The entity is administratively up Down — The entity is administratively down |
|
Agg. Limit |
The agg-rate adaptation rule setting |
|
AIS |
The number of AIS cells transmitted and received on this connection for both end to end and segment |
|
AIS-P |
The number of AIS-P packets received |
|
Alarm Status |
The bits used to indicate alarms: loc — A loss of clock which causes the operational state of the port to be downed lais — Line alarm indication signal errors lrdi — Line remote defect indication errors. LRDIs are caused by remote LOF, LOC, and LOS ss1f — Section synchronization failure as reported by the S1 byte sb1err — Section B1 errors lb2erSd — Line signal degradation BER errors lb2erSf — Line signal failure BER errors slof — Section loss of frame errors slos — Section loss of signal errors stxptr — Section synchronization error on the transmit side. Indicates if there is a positive or negative justification count per channel srxptr — Section synchronization error on the receive side. Indicates if there is a positive or negative justification count per SONET path lrei — Line error condition raised by the remote as a result of B1 errors received from this node |
|
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets |
|
Altitude (m MSL) |
The altitude of the GNSS antenna above mean sea level, in meters |
|
Amplifier Gain (dB) |
The amplifier gain high and low warning alarms |
|
Amplifier Input Power (dBm) |
The amplifier input power high and low warning alarms |
|
Amplifier Output Power (dBm) |
The amplifier output power high and low warning alarms |
|
AN |
The AN for identifying the receiving SA |
|
Ant. Cable Delay |
The amount of time, in nanoseconds, compensated for signal delay because of cable length Refer to the cable manufacturer data to determine accurate signal delay statistics for the type and length of cable used |
|
Antenna status |
ok: valid antenna connection under-current: open condition. The port remains operationally up in the event that any GNSS splitters used do not provide a load. over-current: short circuit, or maximum power limits for the receiver have been exceeded no-bias voltage: antenna power disabled |
|
Assigned ports |
Specifies all ports that contain this CA |
|
authentication method |
The 802.1x session authentication method |
|
Authenticator PAE state |
The 802.1x port authenticator PAE state |
|
Auto-negotiate |
True — The link attempts to automatically negotiate the link speed and duplex parameters False — The duplex and speed values are used for the link |
|
Average Elapsed Time |
The average elapsed time |
|
Backend state |
The 802.1x port backend state |
|
Bad Tag Packets |
The number of received packets discarded with an invalid SecTAG or a zero value Packet Number (PN) or an invalid Integrity Check Value (ICV) |
|
BFD Spoof Check Failed |
The received BFD packet either failed the TTL check (single hop BFD TTL should be 255) or failed the source IP address lookup of known sessions. This counter may increment when BFD sessions are first configured since one side may start sending before the other is completely programmed and ready. |
| Breakout | The connector breakout configured for the port |
|
Broadcast Packets Input/Output |
The number of packets, delivered by this sub-layer to a higher (sub-) layer, which were addressed to a broadcast address at this sub-layer. The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. |
|
Broadcast Packets |
Input — The number of input broadcast packets Output — The number of output broadcast packets |
|
Broadcast Pckts |
The number of packets, delivered by this sub-layer to a higher (sub-) layer, which were addressed to a broadcast address at this sub-layer. The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. |
|
CA name/ca-name |
The CA name assigned to the port |
|
Cast Type |
The connection topology type |
|
CBS |
The CBS value defining the reserved size for the queue |
|
Cells |
The number of input and output cells HEC discarded cells are not included in the input cell numbers |
|
Cfg Alarm |
The alarms that are reported when raised or cleared. Alarms that are not in this list are not reported when they are raised or cleared but appear in the Alarm Status. pais — Path alarm indication signal errors plop — Path loss of pointer (per tributary) errors prdi — Path remote defect indication errors pb3err — Path B3 errors pplm — Path payload mismatch. As a result, the path can be operationally downed prei — Path error condition raised by the remote as a result of B3 errors received from this node puneq — Unequipped path errors. plcd — Path loss of codegroup delineation error. It is applicable only when the value of tmnxPortEtherXGigMode is set to 'wan'. |
|
Cfg MTU |
The configured MTU |
|
Cfg Rx Channel |
The configured DWDM ITU channel at which the coherent optical module is expected to operate |
|
Cfg Rx LOS Thresh |
The configured LOS threshold of the average input power |
|
Cfg Tx Pwr Maximum |
The maximum power setting supported by the transceiver (only displayed if the equipped optical module supports configurable transmit power) |
|
Cfg Tx Pwr Minimum |
The minimum power setting supported by the transceiver (only displayed if the equipped optical module supports configurable transmit power) |
|
Cfg Tx Target power |
The manually-configured average target output power |
|
Chan-Grp IfIndex |
The channel group’s interface index number which reflects its initialization sequence |
|
Cipher Suite |
The cipher suite used for encrypting the SAK: gcm-aes-128, gcm-aes-256, gcm-aes-xpn-128, gcm-aes-xpn-256 |
|
CIR Rule |
min — The operational CIR for the queue is equal to or greater than the administrative rate specified using the rate command except where the derived operational CIR is greater than the operational PIR. If the derived operational CIR is greater than the derived operational PIR, the operational CIR will be made equal to the operational PIR. max — The operational CIR for the queue is equal to or less than the administrative rate specified using the rate command. closest — The operational CIR for the queue is the rate closest to the rate specified using the rate command without exceeding the operational CIR. |
|
CIR Weight |
The weight the queue or scheduler uses at the within-CIR port priority level |
|
Clear Tag Mode |
In the case of VLAN-tagged traffic, if the traffic is crossing a network, one or two VLAN tags can be transmitted in clear text so that this traffic can receive preferential treatment over the network based on 802.1 q-tag or p-bits. Values: single-tag, dual-tag |
|
Coherent Optical Module |
Information for the coherent optical module |
|
Coherent Optical Port Statistics |
Statistics for the coherent optical port For Coherent CFP, the Rx Power field displays per-channel power. |
|
Collect-stats Collect Stats |
Enabled — The collection of accounting and statistical data for the network Ethernet port is enabled. When applying accounting policies the data by default will be collected in the appropriate records and written to the designated billing file. Disabled — Collection is disabled. Statistics are still accumulated by the IOM cards, however, the CPU will not obtain the results and write them to the billing file. |
|
Collisions |
The best estimate of the total number of collisions on this Ethernet segment |
|
Config Duplex |
Full — The link is set to full duplex mode Half — The link is set to half duplex mode |
|
Config Revision |
The configuration revision |
|
Config Speed |
The configured speed of the interface |
|
Configured Address |
The configured Ethernet MAC address |
|
Configured Freq |
The configured frequency for the transceiver |
|
Configured Mode |
network — The port is configured for transport network use access — The port is configured for service access |
|
Configured Mode |
network — The port is configured for transport network use access — The port is configured for service access. Channelized ports are always access ports |
|
Configured VCs |
The number of configured VCs |
|
Connector Code |
The vendor organizationally unique identifier field (OUI) contains the IEEE company identifier for the vendor |
|
Constellation |
The type of GNSS satellite navigation system used |
|
CRC |
The precision of the cyclic redundancy check. 16 — A 16-bit CRC calculation. 32 — A 32-bit CRC calculation. 32-bit CRC increases the error detection ability, but it also adds some performance overhead. |
|
CRC Mon SD Thresh |
The error rate (for CRC errors) at which to declare the Signal Degrade (SD) condition on an Ethernet interface. If the field displays Disabled, no error rate has been specified. |
|
CRC Mon SF Thresh |
The CRC error rate at which to declare the Signal Fail (SF) condition on an Ethernet interface. If the field displays Disabled, no error rate has been specified. |
|
CRC Mon Window |
The size of the sliding window, in seconds, over which the Ethernet frames are sampled to detect signal fail or signal degrade conditions. |
|
CRC/Align Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). |
|
CRC-10 Errors |
The number of cells discarded on this VPL with CRC 10 errors |
|
CRC-32 Errors |
The number of valid AAL-5 SDUs and AAL-5 SDUs with CRC-32 errors received by the AAL-5 VCC |
|
CSE |
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface |
|
CV-P |
The number of Coding Violations |
|
Current Freq |
The current frequency |
|
Current Penalties |
The current accumulated penalties for port dampening |
|
DAC Percent |
The DAC percentage of the transceiver |
|
Dampening State |
The port dampening state: Disabled, Idle, or Active |
|
Data Rate |
The data rate at which the port is operating. When OTU is encapsulating 10-Gigabit Ethernet WAN, the data rate is 10.709 Gb/s, the G.709 standard OTU2 data rate. When OTU is encapsulating 10-Gigabit Ethernet LAN, the data rate is either 11.049 Gb/s or 11.096 Gb/s, depending on the otu2-lan-data-rate configuration parameter of the port's OTU parameters. These data rates (11.049 Gb/s and 11.096 Gb/s) are considered OTU2e data rates that are non-standard or over-clocked with respect to G.709, but have become widely used in optical networking to transport un-altered 10-Gigabit Ethernet LAN payloads. |
|
DDM Events |
Enabled — DDM events are enabled Disabled — DDM events are disabled |
|
Decrypted Octets |
The number of octets of plain text recovered from received packets that were integrity protected and encrypted |
|
Delayed Packets |
The number of received packets with the condition a PN lower than the lower bound of the replay protection on this SC |
|
Description |
A text description for the entity |
|
Diag Capable |
Indicates whether the transceiver is capable of performing diagnostics |
|
Discards |
Input — The number of discarded input packets Output — The number of discarded output packets |
|
Discards Input/Output |
The number of inbound packets chosen to be discarded to possibly free up buffer space |
|
Disp Control Mode |
The current operational mode of the tunable dispersion compensation module |
|
DOIE Tx Disable |
Enabled — Laser is enabled if an internal MAC transmit error is encountered Disabled — Laser is disabled if an internal MAC transmit error is encountered |
|
Dot1Q Ethertype |
The Ethertype expected when the port's encapsulation type is Dot1Q |
|
Down On Int. Error |
Enabled — Down on internal error feature is enabled Disabled — Down on internal error feature is disabled |
|
Down-when-looped |
The feature is enabled or disabled |
|
Drop Count |
The number of keepalive or LQR messages that were missed before the line was brought down |
|
Dropped |
The number of dropped packets and octets |
|
Drop Events |
The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected. |
|
Dropped CLP |
The number of times the CLP1 cells have been dropped. CLP1 cells have lower priority than CLP0 cells and are expected to be discarded first in times of congestion. |
|
Dying Gasp |
Indicates whether dying gasp is enabled or disabled |
|
Dying Gasp on Reset |
EFM OAM dying gasp messages on reset: true or false |
|
eapol-destination-address |
The destination MAC address used in the EAPoL packet for MACsec Key Agreement (MKA) PDUs |
|
EgrAmp |
The egress amplifier alarm information, including:
|
|
Encryption Offset |
The encryption offset configured on this node: 0, 30, 50. In the case of IP traffic, the IP header can be transmitted in clear text so that the traffic is routed accordingly when crossing the network. A value of 30 is used for IPv4 and 50 for IPv6. |
|
EFM OAM |
Enabled — EFM OAM is enabled Disabled — EFM OAM is disabled |
|
EFM OAM Link Mon |
Enabled — Link monitoring functionality is enabled Disabled — Link monitoring functionality is disabled |
|
Egr. Sched. Pol |
The port scheduler policy or that the default policy default is in use |
|
Egress CBR |
The total CBR bandwidth consumed on this interface in the egress direction |
|
Egress NRT-VBR |
The total non-real-time variable bit rate (nrt-VBR) bandwidth consumed on this interface in the egress direction |
|
Egress Octets |
The egress octets on a per-port basis |
|
Egress Packets |
The egress packets on a per-port basis |
|
Egress Rate |
The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate |
|
Egress RT-VBR |
The total real-time variable bit rate (rt-VBR) bandwidth consumed on this interface in the egress direction |
|
Egress UBR |
The total unspecified bit rate (UBR) bandwidth consumed on this interface in the egress direction |
|
Elev. Mask Angle |
The configured elevation angle below which satellites are ignored. The default elevation mask angle is 10°. Five or more satellites must be in view of the GNSS receiver antenna at all times when the receiver is in the process of obtaining a position fix, and these satellites must be above the configured elevation mask angle. |
|
Encap-match |
Specifies which types of traffic MACsec is enabled for |
|
Encap Type |
Null — Ingress frames will not use any tags or labels to delineate a service dot1q — Ingress frames carry 802.1Q tags where each tag signifies a different service |
|
Encap Value |
The dot1q or qinq encapsulation value on the port for this IP interface |
|
Encrypted Octets |
The number of plain text octets that are integrity protected and encrypted on the transmitting SC |
|
Encrypted Packets |
The number of packets that are integrity protected and encrypted for this transmitting SA |
|
Encrypted SA Packets |
The number of packets that are integrity protected and encrypted for this SA |
|
Encryption Offset |
Specifies the encryption offset configured on this node: 0, 30, 50. In the case of IP traffic, the IP header can be transmitted in clear text so that the traffic is routed accordingly when crossing the network. A value of 30 will be used for IPv4 and 50 for IPv6. |
|
Endpoint Type |
The endpoint type |
|
Errored Frame Enabled |
Specifies whether errored frames are enabled |
|
Errored Frame Event Notify |
Specifies whether errored frame events notification is enabled |
|
Errored Frame Period Enabled |
Specifies whether an errored frame period is enabled |
|
Errored Frame Period Event Notify |
Specifies whether an errored frame period event notification is enabled |
|
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
|
ESMC Tunnel |
Indicates whether ESMC frames are tunneled in Epipe or VPLS service |
|
ES-P |
The number of Errored Seconds |
|
Exceed Drop |
The queue depth beyond which exceed-profile packets are not accepted into the queue and are discarded |
|
Excess Collisns |
The number of frames for which transmission on a particular interface fails due to excessive collisions |
|
Far End |
The SONET path far end |
|
FCS Errors |
The number of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check |
|
FEC Corrected 0s |
The number of bits that were received as 0s but corrected to 1s |
|
FEC Corrected 1s |
The number of bits that were received as 1s but corrected to 0s |
|
FEC Mode |
Type of FEC (Forward Error Correction) in effect: g709, enhanced or disabled. When g709 is selected, the standard FEC method is used. When enhanced is selected, a proprietary FEC algorithm is used that extends optical reach in long haul applications. When disabled the bytes that are reserved for FEC in the OTU frame are transmitted as zeros and the FEC decoder is bypassed, but OTU framing is still in effect. |
|
FEC SES |
The number of severely Errored seconds were the number of uncorrectable sub-rows was greater than 15% of the maximum |
|
FEC Uncorrectable Sub-Rows |
The number of sub-rows that were not corrected because too many errors were detected |
|
Fifo Error |
The number of FIFO errors |
|
Fine Tuning |
Indicates whether the transceiver supports fine tuning for the frequency |
|
FIR Rule |
The queue FIR rule |
|
Firmware Version |
Firmware version of the GNSS receiver |
|
FR Interface Status |
The status of the Frame Relay interface as determined by the performance of the DLCMI. If no DLCMI is running, the Frame Relay interface stays in the running state indefinitely. |
|
Forwarded |
The number of forwarded packets and octets |
|
FP Number |
The number of the FP that manages this port |
|
Fragments |
The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
|
Frame Based Acc |
Frame-based accounting for queues parented to the scheduling policy and for the schedulers within the scheduler policy |
|
Grace Tx Enable |
Specifies whether grace Tx is enabled |
|
Grace Vendor OUI |
The EFM OAM grace vendor Organizationally Unique Identifier (OUI) |
|
Grp-<name> Group Name |
The group name |
|
Half Life |
The time, in seconds, that must pass before penalties decay to one-half the initial amount |
|
Hardware Address |
The interface's hardware or system assigned MAC address at its protocol sub-layer |
|
HEC Errors (Dropped) |
The number of cells with uncorrectable HEC errors on this interface |
|
HEC Errors (Fixed) |
The number of fixed HEC errors on this interface |
|
HiPlus Drop Tail |
The queue depth beyond which inplus-profile packets are not accepted into the queue and are discarded |
|
Hi Drop Tail |
The queue depth beyond which in-profile packets are not accepted into the queue and are discarded |
|
Hold Time |
The EFM OAM hold-time |
|
Hold time down |
The link down dampening time in seconds. The down timer controls the dampening timer for link down transitions |
|
Hold Time Down Rmng |
The time remaining for a hold down timer. If the hold timer is not active, this displays zero. |
|
Hold time up |
The link up dampening time in seconds. The port link dampening timer value which reduces the number of link transitions reported to upper layer protocols. |
|
Hold Time Up Rmng |
The time remaining for a hold up timer. If the hold timer is not active, this displays zero. |
|
HS Turbo Queues |
HS turbo queues that allow the corresponding HSQ queue group queues for higher throughput |
|
IfIndex |
The interface's index number which reflects its initialization sequence |
|
Ignore Efm State |
The suppress port operational state changes due to EFM OAM: true or false |
|
Ignr EFM OAM State |
Enabled — Any failure in the protocol state machine does not impact the state of the port Disabled — The port state is affected by any existing EFM-OAM protocol fault condition |
|
Index 1 |
Management IP information, one per type maximum (system IPv4, IPv6 system, oob, oob IPv6) |
|
IngAmp |
The ingress amplifier alarm information, including:
|
|
In Packets |
The number of echo-reply packets received |
|
In Pause Frames |
The number of In Pause frames |
|
Ingress CBR |
The total CBR bandwidth consumed on this interface in the ingress direction |
|
Ingress NRT-VBR |
The total non-real-time variable bit rate (nrt-VBR) bandwidth consumed on this interface in the ingress direction |
|
Ingress Octets |
The ingress octets on a per-port basis |
|
Ingress Packets |
The ingress packets on a per-port basis |
|
Ingress Port Forwarding Engine Drop Reason Statistics |
When any of the packet counters increments, it indicates that a packet was dropped in the ingress data path or extracted to the control plane for further processing. The detailed per-reason drop statistics are available per-port for Ethernet ports (local on the 7450 ESS, 7750 SR, 7950 XRS, or satellite client ports) and for PXC sub-ports. An aggregate forwarding engine drop counter (packet and byte) is available per-SAP. |
|
Ing. QGroup |
The ingress queue group name |
|
Ingress Rate |
The maximum amount of ingress bandwidth (in mb/s) that this Ethernet port can receive with the configured sub-rate using packet-based accounting |
|
Ingress RT-VBR |
The total real-time variable bit rate (rt-VBR) bandwidth consumed on this interface in the ingress direction |
|
Ingress UBR |
The total unspecified bit rate (UBR) bandwidth consumed on this interface in the ingress direction |
|
Host-Matches |
A string optionally used by subscriber management to map subscriber's and subscriber host's queued traffic to a specific egress port virtual port |
|
Input/Output |
When the collection of accounting and statistical data is enabled, then octet, packet, error, and utilization statistics are displayed |
|
Instance-Id |
The queue-group instance ID |
|
Int MAC Rx Errs |
The number of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error |
|
Int MAC Tx Errs |
The number of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error |
|
Interface |
The port ID displayed in the slot/mda/port format |
|
Interface-name port-id |
The interface name of the port |
|
ip ip-address |
The IP address |
|
IP Route Blackholed |
The destination IP address of the packet matches a black hole route |
|
IPv4 Header Error |
The IPv4 packet header contains an error such as an IPv4 header checksum error, an invalid IP version number (not 4 or 6), or an incorrect Total Length field |
|
IPv4 Invalid Address |
An error in the source (SA) or destination (DA) IPv4 address was detected. For example class D or class E IPv4 DAs, loopback SA (127.0.0.0/8), 0.0.0.0/8 DA, SA is a subnet broadcast or network address and cases where the IPv4 address is a multicast address but the Ethernet destination address is not RFC1112 compliant. RFC1112 checks are also carried out on Ipipe traffic. |
|
IPv6 Header Error |
The IPv6 packet header contains an error such as an incorrect Payload Length field or an IP version not equal to '6' when the Ethernet etype indicates it is IPv6 |
|
IPv6 Invalid Address |
An error in the source (SA) or destination (DA) IPv6 address was detected. For example, an unspecified IPv6 DA, an IPv6 multicast SA and cases where the IPv6 address is a multicast address but the Ethernet destination address is not RFC2464 compliant. RFC 2464 checks are also carried out on IPIPE traffic. |
|
Jabbers |
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
|
Keep Alive |
The time interval, in seconds, between keep-alive PDUs |
|
L2 Service MTU Exceeded |
The length of the packet received on a SAP bound to a layer 2 service (such as VPLS or EPIPE) exceeded the configured MTU for the service |
|
LACP Tunnel |
Indicates whether LACP packet tunneling is enabled or disabled |
|
LAG ID |
The LAG or multi-link trunk (MLT) that the port is assigned to |
|
Laser Tunability |
The laser tune-ability of the transceiver |
|
Last Changed |
The date and time when the interface connection entered its current operational state |
|
Last Cleared Last Cleared Time |
The date and time the restart count reset to zero |
|
Last cleared time Last Cleared Time |
The time of the last clear |
|
last session id |
The 802.1x last session ID |
|
last session term cause |
The 802.1x last session term cause |
|
last session time |
The 802.1x last session time |
|
last session username |
The 802.1x last session username |
|
Last State Change |
The system time moment that the entity is up |
|
Last Unknown VPI/VCI |
The last unknown VPI/VCI that was received on this interface |
|
Late Collisions |
The number of times that a collision is detected on a particular interface later than one slot time into the transmission of a packet |
|
Late Packets |
The number of received packets that have been discarded due to replay window protection on this SC |
|
Latitude |
The latitude of the GNSS antenna |
|
LCD-P |
The number of LCD-P packets received |
|
Level |
The level number |
|
Licensed |
The licensed state |
|
Limit Unused BW |
The aggregate rate overrun protection on the aggregate context |
|
Link Length support |
The link length support for the transceiver |
|
Link Monitoring |
The EFM OAM link monitoring parameters: enabled or disabled |
|
Link-level |
Ethernet — The port is configured as Ethernet SONET — The port is configured as SONET-SDH |
|
LMI Type |
The LMI type |
|
Load-balance-algo |
The load balancing algorithm used on the port |
|
Local Magic Number |
The local magic number to be sent to the peer. The magic number provides a method to detect loopbacks. If the value of the local magic number is the same as the value of remote magic number, then it is possible that the link might be looped back. If the two magic numbers do not match, then the link is not looped back. |
|
Longitude |
The longitude of the GNSS antenna |
|
Loopback |
The number of loopback requests and responses transmitted and received on this connection for both end to end and segment |
|
Loop Detected |
True — Loop detected False — No loop detected |
|
LOP-P |
The number of Loss Of Pointer path (LOP) occurrences |
|
Low Drop Tail |
The low drop tail percent reduction from MBS |
|
mac mac-address |
The MAC address |
|
MAC Chip Number |
The number of the MAC chip that manages this port |
|
Macsec Encrypt |
Enabled — MACsec encryption is enabled on the traffic. All fields behind source or destination MAC addresses are encrypted on each packet. Disabled — MACsec encryption is disabled for the traffic. The packet fields are sent in clear text but data integrity is checked on each packet, and the MACsec overhead (header and ICV) is still added to each packet. |
|
macsec-enabled |
The MACsec is enabled or disabled |
|
Manufacture date |
The manufacturing date of the hardware component in the mmddyyyy ASCII format |
|
Max auth requests |
The 802.1x port maximum authorization requests |
|
Max Packet Error |
The number of maximum packet errors |
|
Min Packet Error |
The number of minimum packet errors |
|
Max Penalties |
The maximum penalty value for port dampening |
|
Maximum Frequency |
The supported maximum frequency for the transceiver |
|
Max Suppress Time |
Elapsed time, in seconds, after the link comes up before the worst case accumulated penalties have decayed to the reuse threshold |
|
MBS |
The MBS value defining the maximum size for the queue |
|
Media |
The media supported for the SFP |
|
Min Frame Length |
The configured minimum transmitted frame length |
|
Minimum Frequency |
The supported minimum frequency for the transceiver |
|
MKA Key Server Priority |
The MKA key server priority: 0 to 255 (default 16). A priority of 0 means more it is more likely to become the MKA server. If multiple participants have the same priority, the MAC address becomes the differentiator for electing the MKA server. |
|
Mode |
The mode of the interface. It can be set as Data Terminal Equipment (DTE) or Data Circuit-terminating Equipment (DCE) |
|
Mode |
The mode of OAM operation for an Ethernet port: active or passive |
|
Model Number |
The model number of the transceiver or adapter |
|
Monitor Depth |
Queue depth monitoring for the specified queue enabled or disabled |
|
Monitor Oper Group |
Operational group being monitored |
|
Monitor Port Sched |
Enabled — Congestion monitoring on an Egress Port Schedule (EPS) is enabled Disabled — Congestion monitoring on an EPS is disabled |
|
MTU |
The size of the largest packet which can be sent/received on the Ethernet physical interface, specified in octets |
|
Mult Collisions |
The number of frames that are involved in more than one collision and are subsequently transmitted successfully |
|
Multicast MAC With Unicast Dest IP |
The Ethernet destination (MAC) address is multicast but the IP address is unicast |
|
Multicast Packets Input/Output |
The number of packets, delivered by this sub-layer to a higher (sub-) layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both group and functional addresses. The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. |
|
Multicast Packets |
Input — The number of input multicast packets Output — The number of output multicast packets |
|
Multicast Pckts |
The number of packets, delivered by this sub-layer to a higher (sub-) layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. |
|
Name |
The entity name |
|
Needs ICMP |
The received packet requires the router to generate an ICMP message. For example, the IP packet TTL is expired or the destination host, network, or ESM subscriber is unreachable. Host unreachable can occur, among other reasons, if the destination address (for example, 10.0.1.2) of a packet resolves to a loopback interface subnet (for example, 10.0.1.1/24) but does not match the specific loopback address (for example, 10.0.1.1). Destination unreachable can also occur, for example, in response to an IPv6 packet received by a router from a point-to-point link (a non-Ethernet link) destined to an address within a subnet assigned to that same link (other than one of the receiving router's own addresses) as described in RFC 4443. |
|
Net. Egr. Queue Pol |
The network egress queue policy or that the default policy is used |
|
No SCI Packets |
The number of received packets discarded with unknown SCI information when the C bit in the SecTAG is set |
|
No Tag Packets |
The number of received packets discarded without the MAC security tag (SecTAG) |
|
No Using SA Packets |
The number of received packets that have been discarded on this SA which is not currently in use |
|
Notifications |
LLDP notifications (enabled, disabled) |
|
Not Valid Packets |
The number of not valid packets that have been discarded on this active SA |
|
Number OCD Events |
The number of times the Out of Cell Delineation (OCD) events occurred |
|
Number of Lanes |
The number of lanes of the transceiver |
|
Number of Logs |
The number of logs |
|
Octets |
The number of input and output octets. HEC discarded cells are not included in the input octet numbers. |
|
Octets |
The total number of octets received |
|
OctetsIn Dropped |
The number dropped egress octets that were in-profile |
|
OctetsIn Forwarded |
The number of forwarded egress octets that were in-profile |
|
OctetsIn Total |
The total number of egress octets that were forwarded and dropped |
|
OctetsOut Dropped |
The number of dropped egress octets that were out-of-profile |
|
OctetsOut Forwarded |
The number of forwarded egress octets that were in-profile |
|
OctetsOut Total |
The total number of egress octets that were forwarded and dropped |
|
OK Packets |
The number of validated packets on this SA |
|
Oper Duplex |
full — The link is set to full duplex mode half — The link is set to half duplex mode |
|
Oper Egress Rate |
The operational egress bandwidth (in kilobits per second) that the Ethernet interface can generate |
|
Oper MTU |
The negotiated size of the largest packet that can be sent on the port SONET/SDH, channel, specified in octets. For channels that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the channel. |
|
Oper Speed |
The operating speed of the interface |
|
Oper State |
up — The entity is operationally up down — The entity is operationally down Additionally, the lag-id of the LAG it belongs to in addition to the status of the LAG member (active or standby) is specified |
|
Oper Status |
The operational status of the port |
|
Oper Status |
up: the port is operationally up (communication between the main board and the GNSS receiver is established and the port is ready to receive GNSS signals) down: the port is operationally down (none of the up conditions have been met) |
|
Operational Channel |
The operational channel for the transceiver |
|
Operational Frequency |
The operational frequency for the transceiver |
|
Optical Compliance |
The optical compliance code of the transceiver |
|
Optical Compliance |
The optical compliance code of the transceiver |
|
Other |
The number of OAM cells that are received but not identified |
|
OTU Status |
The status of the OTU (Optical Transport Unit): enabled or disabled. When OTU is enabled, and additional layer of framing encapsulates an MDA's natively programmed mode of operation, 10-Gigabit Ethernet LAN or WAN, adding SONET-Like Framing with FEC (Forward Error Correction). When OTU is disabled, the MDA operates in a 10-Gigabit Ethernet LAN or WAN as per Ethernet provisioning. |
|
Out packets |
The number of echo-request packets sent |
|
Out Pause Frames |
The number of Out Pause frames |
|
Over Sized SDUs |
The total number of oversized SDU discards |
|
Overrun Packets |
The number of packets discarded because the number of received packets exceeded the cryptographic performance capabilities |
|
Oversize Pckts |
The total number of packets received that were longer than can be accepted by the physical layer of that port (9900 octets excluding framing bits, but including FCS octets for GE ports) and were otherwise well formed |
|
Packet Abort Error |
The number of packets aborted due to errors received |
|
Packets |
The total number of packets received |
|
Packets |
The number of input and output packets. Packets discarded due to HEC or oversize discards are not counted. CRC errors are also in the packet counts show up on the VC level statistics but not on the port level. |
|
PacketsIn Dropped |
The number dropped egress packets that were out-of-profile |
|
PacketsIn Forwarded |
The number of forwarded egress packets that were in-profile |
|
PacketsIn Total |
The total number of egress packets that were forwarded and dropped |
|
PacketsOut Dropped |
The number of dropped egress packets that were out-of-profile |
|
PacketsOut Forwarded |
The number of forwarded egress packets that were in-profile |
|
PacketsOut Total |
The total number of egress packets that were forwarded and dropped |
|
Parity Error |
The number of parity errors received |
|
Part Number |
The vendor part number contains ASCII characters, defining the vendor part number or product name |
|
PBB Ethertype |
The Ethertype used for PBB encapsulation |
|
Per Threshold MDA Discard Statistics |
See the 7450 ESS, 7750 SR, 7950 XRS, and VSR Interface Configuration Guide, "Packet Classification and Scheduling” section |
|
Phy Link Physical Link |
Yes — A physical link is present No — A physical link is not present |
|
Phys State Chng Cnt |
Increments when a fully qualified (de-bounced) transition occurs at the physical layer of an Ethernet port which includes the following transitions of the Port State as shown in the show port summary: - from "Down” to either "Link Up” or "Up” - from either "Link Up” or "Up” to "Down” This counter does not increment for changes purely in the link protocol states (for example, "Link Up" to "Up"). The counter is reset if the container objects for the port are deleted (for example, MDA deconfigured, or IOM type changes). |
|
PIR Rule |
min — The operational PIR for the queue is equal to or greater than the administrative rate specified using the rate command max — The operational PIR for the queue is equal to or less than the administrative rate specified using the rate command closest — The operational PIR for the queue is the rate closest to the rate specified using the rate command |
|
Physical Link |
Yes — A physical link is present No — A physical link is not present For GNSS ports: Yes — The port is operationally up (communication between the main board and the GNSS receiver is established and the port is ready to receive GNSS signals. For example, if the GNSS port is configured, the operational status is up, the receiver status is 3D FIX, and you disconnect the GNSS RF cable from the port, the physical link on the port still shows as up. No — The port is operationally down (none of the up conditions apply) |
|
PLM-P |
The number of PLM-P packets received |
|
PM BEI |
The number of backward error indications received from the far end in the path monitor overhead |
|
PM BIP8 |
The number of detected BIP-8 errors in the path monitor overhead |
|
PM SES |
The section monitor severely errored seconds where the number of PM-BIP8 was greater than 15% of the maximum |
|
Polar Depend Loss (dB) |
The polarization dependent loss in decibels |
|
Policy-Name |
The policy name |
|
Port control |
The 802.1x port control: auto, force-auth, force-unauth |
|
Port Encap |
Null — Ingress frames will not use tags or labels to delineate a service dot1q — Ingress frames carry 802.1Q tags where each tag signifies a different service |
|
Port ID |
The port ID that is configured or displayed. |
|
Port <id> Bridge nearest-bridge |
|
|
Port <id> Bridge nearest-non-tpmr |
|
|
Port <id> Bridge nearest-customer |
|
|
Port IfIndex |
The GNSS interface index number, which reflects its initialization sequence |
|
Port Mode |
Network — The port is configured for transport network use Access — The port is configured for service access Hybrid — The port is configured for both access and network use |
|
Port State |
Up — The port is physically present and has physical link present Down — The port is physically present but does not have a link. This state may also be considered as Link Down Ghost — A port that is not physically present None — The port is in its initial creation state or about to be deleted Link Up — A port that is physically present and has physical link present Note that when Link Up appears at the lowest level of a SONET/SDH path or a TDM tributary, it means the physical connection is active but the port is waiting on some other state before data traffic can flow. It is a waiting state and indicates that data traffic will not flow until it transitions to the Up state. |
|
Port status |
The 802.1x port status |
|
PorID TLV Subtype |
The encoding of the port identifier TLVs transmitted to the peer (tx-if-alias, tx-if-name, tx-local) |
|
Port Type |
The type of port or optics installed |
|
Present Channel |
The channel that the transceiver is currently on |
|
Protected Octets |
The number of plain text octets that are integrity protected but not encrypted on the transmitting SC |
|
Protected Packets |
The number of packets that are integrity protected but not encrypted for this transmitting SA |
|
Protected SA Packets |
The number of packets that are integrity protected but not encrypted for this SA |
|
Protocol |
The applicable protocols for the specified port |
|
PTP TS Capability |
The encapsulation format for 1588 port-based timestamping
|
|
Pump Temperature (C) |
The pump temperature high and low warning alarms |
|
QinQ Ethertype |
The Ethertype expected when the port's encapsulation type is QinQ |
|
Queue |
The queue information |
|
Queue Depths (percentage) |
The queue depth percentages |
|
Queue-Id |
The queue-id that uniquely identifies the queue |
|
Quiet period |
The 802.1x port quiet period: 1 to 3600 seconds |
|
Radius-plcy |
The 802.1x port RADIUS policy name |
|
Range |
The usable range to fine tune the frequency |
|
RDI |
The number of RDI cells transmitted and received on this connection for both end to end and segment |
|
RDI-P |
The number of RDI-P packets received |
|
Reassembly Timeouts |
The number of reassembly timeout occurrences |
|
Reauth enabled |
no — The 802.1x port reauth enabled is not up yes — The 802.1x port reauth enabled is up |
|
Reauth period |
The 802.1x port reauthorization period |
|
Receiver status |
Acquiring Satellites: GNSS receiver is attempting to track satellite Position Hold: GNSS receiver position is determined and GNSS receiver is no longer solving for position; TRAIM algorithm is correcting for time bias 2D Fix: GNSS receiver is attempting to obtain a two-dimensional position (latitude, longitude) solution 3D Fix: GNSS receiver is attempting to obtain a three-dimensional position (latitude, longitude, altitude) solution Unknown: default state on power-up Communication Lost: occurs after 30 s of missing Channel/Data/Status messages or TRAIM status messages from the GNSS receiver Communication Established: occurs after a successful reestablishment of communication following a Communication Lost status |
|
Remote Error |
The number of remote error received |
|
Remote Magic Number |
The magic number sent by the peer. If the value of remote magic number is the same as the value of the local magic number, then it is possible that the link might be looped back. If the two magic numbers do not match, then the link is not looped back. |
|
Replay Protection |
Enabled — Replay Protection is enabled Disabled — Replay Protection is disabled If replay protection is enabled for this CA, the out of replay-window packets will be discarded. Otherwise, the Replay Window Size value is ignored. The default value is disabled, so that when adding MACsec to an interface, it will not affect traffic immediately. |
|
Replay Window Size |
The size, in packets, of the replay window. Each packet is assigned a unique packet number. Replay protection enforces strict ordering of the packets and protects against replay attacks. In networks where out-of-order packets are expected, the window size can be set up to 4294967295. |
|
Request Interval |
The time interval in seconds at which keepalive requests are issued |
|
Resolution |
The resolution used to fine tuning the frequency |
|
Restart Count |
The number of times that this Control Protocol has reached the 'open' state |
|
Retry |
The minimum wait time, in seconds, before re-enabling the port after loop detection |
|
Reuse Threshold |
The threshold at which the port up state is no longer suppressed, after the port has been in a suppressed state and the accumulated penalties decay drops below this threshold |
|
RS-FEC Mode |
The RS-FEC mode |
|
RxDTV Adjust |
The Rx DTV adjust status |
|
Rx Ageouts |
The number of LLDP frames received on the port with a properly formatted TLV that was not supported on the receiving port |
|
Rx Frames |
The number of LLDP frames received on the port |
|
Rx Frame Discard |
The number of LLDP frames received but discarded on the port |
|
Rx Frame Errors |
The number of LLDP frames received with errors on the port |
|
Rx Media Frame Error Count |
The receive media frame error count |
|
Rx TLV Discard |
The number of LLDP frames received on the port discarded because of the TLV |
|
Rx TLV Unknown |
The number of LLDP frames received on the port with a properly formatted TLV that was not supported on the receiving port |
|
Rx Total Power (dbm) |
The receive total power |
|
Rx Quality Level |
Indicates which QL value has been received from the interface |
|
Rx Signal Label |
The received signal label |
|
Rx Trace Str (Hex) |
The received SONET path trace string in hexadecimal |
|
sap |
The physical port identifier portion of the SAP definition |
| Sat Port Queue Statistics | The satellite queue statistics with per-queue forward and drop information (packet and octet counters) for satellite uplink and client ports |
|
Sched Policy |
The name of the scheduler policy assigned to the virtual port |
|
SCI |
The Secure Channel Identifier (SCI) |
|
SD Threshold |
The configured error rate threshold at which the SD (Signal Degrade) alarm is raised |
|
Security Zone |
The security zone this port belongs |
|
Serial Number |
The vendor serial number of the hardware component |
|
Server timeout |
The 802.1x port server timeout |
|
Service-id port-id |
The service IDs affected by the encap-match configured under this sub-port. One or more services can be affected by the match (by using * or by targeting ports with traffic aggregations, for example). |
|
SES-P |
The number of Severely Errored Seconds |
|
SF Threshold |
The configured error rate threshold at which the SF (Signal Fail) alarm is raised |
|
SF/SD Method |
The selected method for declaring the SF (Signal Fail) or SD (Signal Degrade) alarm. When BIP8 is selected, the error rate of SM-BIP8 errors in the OTU frames declares SF or SD (This is very similar to SONET SF/SD which uses a rate of B2 errors). When FEC is selected, the rate of corrected bits declares SF or SD. This effectively indicates that the link would be degraded (SD) or failed (SF) if FEC was disabled and gives the user an early warning that the link is degrading or is about to fail. |
|
Sflow |
Enabled — sFlow data collection for the port is enabled Disabled — sFlow data collection is disabled |
|
C/QS/S/XFP/MDI MDX |
Additional information related to the port. This can include optical compliance and the link length if available from the installed optics. If there is no optical compliance information programmed in the part, “Unspecified” is displayed. GIGE — The GigE SFP type FASTE — The FastE SFP type GIGX — The GigX SFP type MDI — Indicates that the Ethernet interface is of type MDI (Media Dependent Interface) MDX — Indicates that the Ethernet interface is of type MDX (Media Dependent Interface with crossovers) |
|
Shaped Bandwidth |
The total shaped bandwidth consumed on this interface in the egress direction |
|
Signal Label |
The C2 byte value |
|
Single Fiber Mode |
Yes - Single fiber option is configured No - Single fiber option is not configured |
|
Slot ID |
The slot number of the card in the chassis |
|
SM BEI |
The number of backward error indications received from the far end in the section monitor overhead |
|
SM BIP8 |
The number of detected BIP-8 errors in the section monitor overhead |
|
SM SES |
Section monitor severely errored seconds where the number of SM-BIP8 was greater than 15% of the maximum |
|
SM-TTI Rx |
This is the SM-TTI (Section Monitor Trail Trace Identifier received by this port. When the received TTI is a printable string of characters, it will be displayed as a text string. When the received TTI contains one or more non-printable characters, it will be displayed at a sequence of 64 hex bytes. When the received TTI is all zeros, the string "Not Specified” will be displayed. |
|
SM-TTI Tx (<mode>) |
This is the configured SM-TTI (Section Monitor Trail Trace Identifier) to be transmitted by this port in the OTU overhead bytes. The modes are auto, string, or bytes. In the auto and string modes, a printable character string will be displayed. In bytes mode, up to 64 hex bytes are displayed. |
|
Sngl Collisions |
The number of frames that are involved in a single collision, and are subsequently transmitted successfully |
|
Speed |
The speed of the DS0 channels used in the associated channel-group |
|
SQE Errors |
The number of times that the SQE TEST ERROR is received on a particular interface |
|
SSM Code Type |
The SSM code type in use on the port |
|
State of polar ROC (krad/s) |
The state of polarization rate of change |
|
Subport |
The MACsec sub-port used. Multiple MACsec instances can be configured under one port, matching traffic based on the encap-match parameter. |
|
subscr Subscriber |
The subscriber ID |
|
Supplicant timeout |
The 802.1x port supplicant timeout |
|
Supply Voltage (V) |
The supply voltage of the DDM |
|
Supported Grids |
A list of supported grids for the transceiver |
|
Suppress Threshold |
The threshold at which the port up state is suppressed until the accumulated penalties drop below the reuse threshold again |
|
Svc ID svc-id |
The service identifier |
|
Symbol Errors |
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present |
|
Sym Mon SD Thresh |
The error rate (for symbol errors) at which to declare the Signal Degrade (SD) condition on an Ethernet interface. If the field displays Disabled, no error rate has been specified |
|
Sym Mon SF Thresh |
The symbol error rate at which to declare the Signal Fail (SF) condition on an Ethernet interface. If the field displays Disabled, no error rate has been specified |
|
Sym Mon Window |
The size of the sliding window, in seconds, over which the errors are measured |
|
Sync Status |
locked: GNSS time is within alarm limits not locked: GNSS time is outside of the alarm limits and/or there is an insufficient number of tracked satellites |
|
Sync. Status Msg |
Whether synchronization status messages are enabled or disabled |
|
Tagged Cells |
The number of cells that have been demoted from CLP0 to CLP1 |
|
Temperature (C) |
The temperature of the DDM |
|
Threshold exceeded |
The number of times that the drop count was reached |
|
Time |
GPS date and time |
|
Time to link drop |
The time remaining before the link will be declared dropped if a keepalive echo reply packet is not received |
|
TimeSlots |
The DS0 time slot used in the T1/E1 channel-group |
|
Too long Frames |
The number of frames received on a particular interface that exceed the maximum permitted frame size |
|
Too Long Packets |
The number of transmitted packets discarded because the packet length is greater than the Maximum Transmission Unit (MTU) of the Ethernet physical interface |
|
Total number of access-egress queue groups |
The total number of access-egress queue groups associated with the queue-group summary |
|
Total number of network-egress queue groups |
The total number of network-egress queue groups associated with the queue-group summary |
|
Total number of access-ingress queue groups |
The total number of access-ingress queue groups associated with the queue-group summary |
|
Tot Sym Mon Errs |
The total number of symbol errors |
|
Trace String |
The SONET path trace string |
|
Traffic Statistics |
See the 7450 ESS, 7750 SR, 7950 XRS, and VSR Interface Configuration Guide, "Statistics on Physical PXC Ports” section |
|
Transceiver Code |
The code for the transmission media |
|
Transceiver Digital Diagnostic Monitoring (DDM) |
Transceiver Digital Diagnostic Monitoring (DDM) information, such as temperature and supply voltage |
|
Transceiver Lane Digital Diagnostic Monitoring (DDM) |
Transceiver lane DDM information, such as lane temperature and Tx bias current |
|
Transceiver Status |
The status of the transceiver |
|
Transceiver Type |
The type of transceiver |
|
Transmit Interval |
The transmit interval of OAMPDUs |
|
Transmit period |
The 802.1x port transmit period |
|
Transmit TLVs |
The LLDP TLV to transmit (port-desc, sys-name, sys-desc, sys-cap) |
|
Trigger Fault |
The triggered EFM OAM fault |
|
Tunneling |
true — The 802.1x port tunneling is on false — The 802.1x port tunneling is not on. |
|
Tunnel Nearest Bridge |
The nearest bridge tunneling frames (enabled, disabled) |
|
Tx DUS/DNU |
Whether the QL value is forcibly set to QL-DUS/QL-DNU |
|
Tx Frames |
The number of LLDP frames transmitted from the port |
|
TX Laser Frequency |
The transceiver laser frequency |
|
TX Laser Wavelength |
The transceiver laser wavelength |
|
Tx Length Err Frames |
The number of LLDP frames transmitted with length error from the port |
|
Tx Quality Level |
The QL value being transmitted out of the interface |
|
Type |
The connection type |
|
UAS-P |
The number of Unavailable Seconds |
|
Unchecked Packets |
The number of packets that have failed the integrity check on this SC |
|
Unequipped |
The number of unequipped packets received |
|
Undersize Pckts |
The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed |
|
Unicast MAC Destination Address Mismatch |
The unicast destination MAC address is a null address or does not match any of the expected MAC addresses associated with the receiving interface. Packets with multicast or broadcast MAC addresses do not increment this counter |
|
Unicast Packets |
Input — The number of input unicast packets Output — The number of output unicast packets |
|
Unicast Packets Input/Output |
The number of packets, delivered by this sub-layer to a higher (sub-) layer, which were not addressed to a multicast or broadcast address at this sub-layer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. |
|
Unicast Packets Input/Output |
The number of packets, delivered by this sub-layer to a higher (sub-) layer, which were not addressed to a multicast or broadcast address at this sub-layer |
|
Unicast RPF Check Failed |
The IP packet failed the unicast reverse path forwarding (uRPF) check |
|
Unknown MAC Destination Address Discarded in VPLS |
The MAC destination address lookup in the MAC FDB failed and the VPLS service is configured to discard packets with unknown destination MAC addresses |
|
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received through the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
|
Unknown Proto Discards |
Input — The number of discarded unknown protocol packets |
|
Untagged Packets |
The number of transmitted packets without the MAC security tag (SecTAG) when the value oftmnxMacsecConnAssocReplayProtect for the configured CA is set to 'false' |
|
Use Broadcast Addr |
True — Indicates that the broadcast address is to be used for the destination MAC address False — Indicates that the local port MAC address is to be used for the destination MAC address |
|
Used Satellites |
Displays the number of tracked satellites |
|
user rx frames |
The 802.1x session user Rx frames |
|
user rx octets |
The 802.1x session user Rx octets |
|
user tx frames |
The 802.1x session user Tx frames |
|
user tx octets |
The 802.1x session user Tx octets |
|
UTC offset |
Displays the difference between GPS time and UTC time UTC time = GPS time – UTC offset |
|
Utilization Input/Output |
The value computed as the average of the traffic observed over the configured interval, presented as a percentage of the maximum possible traffic |
|
Validated Octets |
The number of octets of plain text recovered from received packets that were integrity protected but not encrypted |
|
Vendor OUI |
The vendor-specific Organizationally Unique Identifier (OUI) field containing the IEEE company identifier for the vendor |
|
Violation Last Seen |
The date and time of the last violation |
|
Violation Threshold Percnt |
The violation threshold percentage |
|
Violation Total Count |
The violation total count |
|
Visable Satellites |
The number of satellites that the GNSS receiver should see at the current time. This number can be 0 if the GNSS receiver has not yet downloaded an almanac, even if Used Satellites is more than 0. |
|
VPI/VCI |
The VPI/VCI values |
|
Vport Name |
The virtual port name |
|
Weight |
The relative weight of this scheduler in comparison to other child schedulers and queues at the same strict level |
|
Wghtd Avg Queue Poll Interval |
The weighted average queue poll interval |
|
Wghtd Avg HiWtrMark Poll Interval |
The weighted average high water mark queue poll interval |
port
Syntax
port [detail]
Context
[Tree] (show port)
Full Context
show port
Description
This command displays information about all ports configured on all cards in the chassis.
Parameters
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of port information.
Output Example*A:cses-V22# show port
===============================================================================
Ports on Slot 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
1/1/1 Down Yes Up 8704 8704 - netw null xcme GIGE-LX 10KM
1/1/2 Up Yes Up 1514 1514 - accs null xcme GIGE-LX 10KM
1/1/3 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/4 Up Yes Up 1514 1514 - accs null xcme GIGE-LX 10KM
1/1/5 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/6 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/7 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/8 Up Yes Up 8704 8704 - hybr dotq xcme GIGE-LX 10KM
1/1/9 Up Yes Up 1518 1518 - accs dotq xcme GIGE-LX 10KM
1/1/10 Down Yes Down 8704 8704 - netw null xcme GIGE-LX 10KM
A:admin@mci(right-b4)# show port
===============================================================================
Ports on Slot 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
1/1/m1/1 Link Up anchor 100G
1/1/c1 Up Link Up conn 100GBASE-LR4*
1/1/c1/1 Up No Down 9212 9212 - netw null xgige
1/1/c1/2 Down No Down 9212 9212 - netw null xgige
1/1/c1/3 Down No Down 9212 9212 - netw null xgige
...
===============================================================================
Ports on Port Cross Connect 1
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
pxc-1.a Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-1.b Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-2.a Up Yes Link Up 1574 1574 - hybr dotq xgige
pxc-2.b Up Yes Link Up 1574 1574 - hybr dotq xgige
port
Syntax
port {port-id | connector-id | connector-port-id | aps-id | esa-vm-id} statistics
port port-id ethernet dampening
port port-id ethernet efm-oam events [local | remote]
port port-id exp-secondary-shaper shaper-name statistics
port port-id fwd-engine drop-reason statistics
port port-id hs-secondary-shaper shaper-name statistics
port port-id monitor-threshold
port port-id hs-pool high-water-mark {[standard value] | [alternate value]}
port port-id phys-state-change-count
port port-id port-scheduler statistics
port port-id queue-group queue-group-name [instance instance-id] queue-depth [ queue queue-id] {ingress | egress} [ access | network]
port port-id queue-group queue-group-name [ instance instance-id] [access | network] { ingress | egress} statistics
port port-id vport [name] monitor-threshold
port port-id vport name statistics
Context
[Tree] (clear port)
Full Context
clear port
Description
This command clears port statistics for the specified ports.
Parameters
- port-id
-
Specifies the physical port identifier.
- aps-id
-
Specifies the APS group identifier.
aps-group-id[.channel]
aps
keyword
group-id
1 to 64
- esa-vm-id
-
Specifies the ESA VM identifier.
- statistics
-
Clears the statistics for the specified port.
- cp
-
Clears Connection Profile statistics.
- interface-connection
-
Clears interface-connection statistics.
- ilmi
-
Clears ILMI information. This parameter is only applicable for ports/bundles that support ILMI.
- pvc
-
Clears PVC statistics.
- pvp
-
Clears PVP statistics.
- pvt
-
Clears PVT statistics.
- slot
-
Specifies the slot number.
- mda
-
The MDA number.
- port-connection
-
Clears port-connection statistics.
- phys-state-change-count
-
Clears the counter that tracks physical port state transitions for ethernet ports ("Phys State Chng Cnt" in "show port" output, or tmnxPortPhysStateChangeCount in the TIMETRA-PORT-MIB).
- port-scheduler
-
Clears the packet and octet counters for the port scheduler that is applied to the specified port.
- queue-group-name
-
Clears the specified port queue group name. It uniquely identifies a port ingress queue group in the managed system, up to 32 characters.
- instance-id
-
Specifies the specific instance of a queue group.
- ingress
-
Clears ingress queue group information.
- egress
-
Clears egress queue group information.
- access
-
Clears access mode statistics for the queue group.
- network
-
Clears network mode statistics for the queue group.
- ethernet
-
Specifies that an Ethernet port will have the clear functions executed.
- dampening
-
Clears the current accumulated penalties of the exponential port dampening feature for the port. The accumulated penalties can be cleared only with this command keyword.
- efm-oam
-
Clears efm-oam statistics on the port.
- events
-
Specifies an efm-oam event will be cleared.
- local
-
Specifies that only local EFM OAM events will be cleared.
- remote
-
Specifies that only remote (received from peer) events will be cleared. Local and remote is not specified.
- shaper-name
-
Clears information about the specified shaper name, up to 32 characters.
- name
-
Clears information about the specified Vport name up to 32 characters.
- standard value
-
Clears high water marks within specific standard port class pools using the standard parameters.
- alternate value
-
Clears high water marks within specific alternative port class pools using the alternative parameters.
Platforms
All
port
Syntax
port port-id
Context
[Tree] (tools>dump port)
Full Context
tools dump port
Description
Commands in this context dump port information.
Parameters
- port-id
-
Specifies the physical port ID.
port-id
slot/mda/port
aps-id
aps-group-id
aps
keyword
group-id
1 to 128
Platforms
All
port
Syntax
port [sap sap-id | sdp sdp-id:vc-id] [group [grp-ip-address]] [detail] [family]
Context
[Tree] (show>service>id>pim-snooping port)
Full Context
show service id pim-snooping port
Description
This command displays PIM port information.
Parameters
- sap-id
-
Displays the port information associated with the specified SAP
- sdp-id:vc-id
-
Displays the port information associated with the specified SDP
- grp-ip-address
-
Specifies the IP multicast group address for which this entry contains information
- detail
-
Displays detailed port information
- family
-
Displays either IPv4 or IPv6 information for the specified port
Platforms
All
Output
The following output is an example of service PIM snooping information.
Output Example*A:PE# show service id 1 pim-snooping port
===============================================================================
PIM Snooping Ports ipv4
===============================================================================
Sap/Sdp Id Opr
-------------------------------------------------------------------------------
SAP:1/1/1 Up
SAP:1/1/2 Up
===============================================================================
*A:PE#
port
Syntax
port port-id [{ingress | egress}] [{access | network}] queue-group queue-group-name [instance instance-id] [{ detail | root-detail | thresholds | priority-info | depth}] [arbiter {name | root}]
Context
[Tree] (show>qos>policer-hierarchy port)
Full Context
show qos policer-hierarchy port
Description
This command displays information about the policer hierarchy per port.
Parameters
- port-id
-
Displays information about the specified port.
- ingress
-
Displays ingress port information.
- egress
-
Displays egress port information.
- access
-
Displays policer-hierarchy statistics applied on the specified access port.
- network
-
Displays policer hierarchy statistics applied on the specified network port.
- queue-group-name
-
Displays information about the specified queue group name, up to 32 characters.
- instance-id
-
Displays information about the instance of the named queue group.
- detail
-
Displays detailed information.
- root-detail
-
Displays detailed information about the arbiter root.
- thresholds
-
Displays the threshold, parenting, rate, and traffic information related to a policer.
- priority-info
-
Displays the threshold information related to the root arbiter.
- depth
-
Displays the bucket depth, parenting, rate, and traffic information related to a policer.
- name
-
Displays information about the name of the QoS arbiter of this forwarding plane.
- root
-
Displays information about the arbiter root.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
port
Syntax
port port-id queue-group queue-group-name [scheduler scheduler-name] [{ ingress | egress}] [{access | network}] [instance instance-id] [detail]
port port-id vport name summary
port port-id [detail]
port port-id vport name [scheduler scheduler-name] [ detail]
Context
[Tree] (show>qos>scheduler-hierarchy port)
Full Context
show qos scheduler-hierarchy port
Description
This command displays scheduler hierarchy information per port.
Parameters
- port-id
-
Specifies the port ID.
port-id
slot/mda/port [.channel]
eth-sat-id
esat-id/slot/port
esat
keyword
id
1 to 20
pxc-id
pxc-id.sub-port
pxc
keyword
id
1 to 64
sub-port
a, b
- detail
-
Displays detailed information.
- queue-group-name
-
Displays information about the specified queue group on the port.
- scheduler-name
-
Displays information about the specified scheduler policy on the port.
- ingress
-
Specifies to display ingress queue group information.
- egress
-
Specifies to display egress queue group information.
- access
-
Displays scheduler-hierarchy statistics applied on an access port.
- network
-
Displays scheduler-hierarchy statistics applied on a network port.
- instance-id
-
Specifies the identification of a specific instance of the queue group.
- vport name
-
Displays statistics for the named VPORT.
Platforms
All
Output
The following output is an example of port scheduler hierarchy information, and Show QoS Schedule-Hierarchy Port Output Fields describes port scheduler hierarchy fields.
Output Example*A:Dut-R# show qos scheduler-hierarchy port 1/2/1 detail
===============================================================================
Scheduler Hierarchy - Port 1/2/1
===============================================================================
Port-scheduler-policy p1
Port Bandwidth : 10000000 Max Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 8]
Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 7]
Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 6]
Rate : max
Consumed : 0 Offered : 0
(Q) : 2->1/2/1:1->3
Assigned : 768 Offered : 0
Consumed : 0
Weight : 0
[Within CIR Level 5]
Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 4]
Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 3]
Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 2]
Rate : max
Consumed : 0 Offered : 0
(S) voip(SAP 1/2/1:1)
Assigned : 0 Offered : 0
Consumed : 0
Weight : 40
(S) all(SAP 1/2/1:1)
Assigned : 19000 Offered : 0
Consumed : 0
Weight : 50
[Within CIR Level 1]
Rate : max
Consumed : 0 Offered : 0
[Within CIR Level 0]
Rate : 0
Consumed : 0 Offered : 0
[Above CIR Level 8]
Rate : max
Consumed : 0 Offered : 0
[Above CIR Level 7]
Rate : max
Consumed : 0 Offered : 0
[Above CIR Level 6]
Rate : max
Consumed : 0 Offered : 0
[Above CIR Level 5]
Rate : max
Consumed : 0 Offered : 0
[Above CIR Level 4]
Rate : max
Consumed : 0 Offered : 0
[Above CIR Level 3]
Rate : max
Consumed : 0 Offered : 0
[Above CIR Level 2]
Rate : max
Consumed : 0 Offered : 0
(S) voip(SAP 1/2/1:1)
Assigned : 10000000 Offered : 0
Consumed : 0
Weight : 30
(S) all(SAP 1/2/1:1)
Assigned : 960000 Offered : 0
Consumed : 0
Weight : 50
[Above CIR Level 1]
Rate : max
Consumed : 0 Offered : 0
(Q) : 2->1/2/1:1->3
Assigned : 786 Offered : 0
Consumed : 0
Weight : 1
===============================================================================
*A:Dut-R#
|
Label |
Description |
|---|---|
|
S |
Displays the scheduler name. |
|
Q |
Displays the queue ID and information. |
|
Admin CIR/PIR: |
Specifies the configured value of CIR/PIR. |
|
Assigned CIR/PIR: |
Specifies the on-the-wire PIR/CIR rate given to a member by that parent level. |
|
Offered CIR/PIR: |
Specifies the on-the-wire offered load on that member. |
|
Consumed CIR/PIR: |
Specifies the amount of scheduler bandwidth used by this member. |
port
Syntax
port port-id queue-group queue-group-name [egress] [{access | network}] [instance instance-id] [ detail]
port port-id vport name [detail]
Context
[Tree] (show>qos>agg-rate port)
Full Context
show qos agg-rate port
Description
This command displays the H-QoS aggregate rate limit per port or Vport.
Parameters
- port-id
-
Specifies the port ID.
port-id
slot/mda/port [.channel]
eth-sat-id
esat-id/slot/port
esat
keyword
id
1 to 20
pxc-id
pxc-id.sub-port
pxc
keyword
id
1 to 64
sub-port
a, b
- queue-group queue-group-name
-
Displays information about the specified queue group on the port.
- egress
-
Displays egress queue group information.
- access
-
Displays H-QoS aggregate rate limit information on an access port.
- network
-
Displays H-QoS aggregate rate limit information on a network port.
- instance instance-id
-
Specifies the identification of a specific instance of the queue-group.
- vport name
-
Displays H-QoS aggregate rate limit information for the specified Vport.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of QoS port aggregation rate output, and Show QoS Aggregation Rate Port Output Fields describes the QoS port aggregation rate fields.
Output Example*A:PE# show qos agg-rate port 1/1/1 queue-group "qg1" instance 1 access egress
===============================================================================
Aggregate Rate Information - Queue Group Port 1/1/1
===============================================================================
-------------------------------------------------------------------------------
Egress Scheduler Policy :
Egress Queue-Group : qg1 Instance-Id : 1
-------------------------------------------------------------------------------
Root (Egr)
| slot(1)
| AdminRate : 10000
| OperRate : 0
| Limit Unused Bandwidth : disabled
| OnTheWireRates : false
| LastMileOnTheWireRates : false
|
-------------------------------------------------------------------------------
===============================================================================
*A:PE#
|
Label |
Description |
|---|---|
|
Egress Scheduler Policy |
Indicates the name of the egress scheduler policy. |
|
Egress Queue-Group |
Indicates the queue group name. |
|
Instance-Id |
Indicates the identifier of a specific instance of the queue group. |
|
AdminRate |
Displays the configured aggregate rate in the subscriber profile. |
|
OperRate |
Displays the actual downstream rate. |
|
Limit Unused Bandwidth |
Indicates whether the limit-unused-bandwidth command is enabled to protect against exceeding the aggregated bandwidth |
|
OnTheWireRates |
Indicates whether the displayed rates are on-the-wire rates. |
|
LastMileOnTheWireRates |
Indicates whether the displayed rates are on-the-wire rates for the last mile only. |
port
Syntax
port port-id [detail]
Context
[Tree] (show>system>ptp port)
Full Context
show system ptp port
Description
This command displays port information.
Parameters
- port-id
-
Specifies the port ID.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of PTP port information and Show PTP Port Output Fields describes the output fields.
Output Exampleshow system ptp port===============================================================================
IEEE 1588/PTP Ethernet Port Summary Information
===============================================================================
Port PTP Adm/Opr PTP State Neighbors Tx Rate Rx Rate
-------------------------------------------------------------------------------
10/2/16 up/up passive 5 12312 4400
1/1/1 up/up slave 1 12312 4400
1/1/2 up/up master 61 12312 4400
1/1/3 up/down disabled 0 0 0
1/1/4 up/up listening 0 0 0
-------------------------------------------------------------------------------
No. of PTP Ports : 5 Total 99999 999999
|
Label |
Description |
|---|---|
|
IEEE 1588/PTP Ethernet Port Summary Information |
|
|
Port |
The port ID |
|
PTP Adm/Opr |
The PTP administrative and operational states |
|
PTP State |
The PTP state |
|
Neighbors |
The neighbors |
|
Tx Rate |
The transmit rate |
|
Rx Rate |
The receive rate |
|
No. of PTP Ports |
The total number of PTP ports |
The following output is an example of PTP port details information and Show PTP Port Detail Output Fields describes the output fields.
Output Exampleshow system ptp port 1/1/4 detail===============================================================================
IEEE 1588/PTP Ethernet Port Information
===============================================================================
Port : 1/1/4
PTP Admin State : up PTP Oper State : up
Local MAC Add : ca:47:01:04:00:02 Mulicast MAC Addr : 01:1b:19:00:00:00
Cfg Sync Rate : 64 pkt/s Cfg Delay Req Rate : 64 pkt/s
Master-Only : false G.8275 Priority : 128
PTP Port Number : 1 PTP Port State : master
Neighbors : 1 Timestamp Point : port
Port Asymmetry : 0 ns
Profile Name : Primary
Profile : ITU-T G.8275.2 Domain : 44
===============================================================================
IEEE 1588/PTP Ethernet Port Neighbor Clocks
Port MAC Address Clock Id Rx Rate Notes
-------------------------------------------------------------------------------
1/1/4 d0:1a:01:01:00:04 ce42fffffe000000 24 unusable
-------------------------------------------------------------------------------
No. of Neighbor Clocks: 1
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
PTP Packets 253 11
Announce 243 1
Sync 0 0
Follow Up 0 0
Delay Request 0 0
Delay Response 0 0
Signaling 10 10
Other 0 0
Discards 0 0
Bad PTP domain 0 0
Alternate Master 0 0
Out Of Sequence 0 0
Packet Timing Signal Fail - Unusable 2848 0
Other 0 0
================================================================================
|
Label |
Description |
|---|---|
|
IEEE 1588/PTP Ethernet Port Information |
|
|
Port |
The port ID |
|
PTP Admin State |
The PTP administrative state |
|
PTP Oper State |
The PTP operational state |
|
Local MAC Addr |
The local MAC address op |
|
Mulicast MAC Addr |
The multicast MAC address |
|
Cfg Sync Rate |
The configured synchronization rate |
|
Cfg Delay Req Rate |
The configured delay request rate |
|
Master-Only |
The master-only value |
|
G.8275 Priority |
The G.8275 priority |
|
PTP Port Number |
The PTP port number |
|
PTP Port State |
The PTP port state |
|
Neighbors |
The neighbors |
|
Timestamp Point |
The timestamp point |
|
Port Asymmetry |
The port asymmetry time |
|
Profile Name |
The profile name |
|
Profile |
The profile |
|
Domain |
The domain |
|
IEEE 1588/PTP Ethernet Port Neighbor Clocks |
|
|
Port |
The port ID |
|
MAC Address |
The MAC address |
|
Clock Id |
The clock ID |
|
Rx Rate |
The receive rate |
|
Notes |
The additional notes |
|
No. of Neighbor Clocks |
The number of neighbor clocks |
|
IEEE 1588/PTP Packet Statistics |
|
|
Input |
The number of input packets within the specified category |
|
Output |
The number of output packets within the specified category |
port
Syntax
port port-id neighbor ieee-address ptsf-unusable statistics
Context
[Tree] (clear>system>ptp port)
Full Context
clear system ptp port
Description
This command clears PTP port information.
Parameters
- port-id
-
Clears the specified port ID.
- ieee-address
-
Specifies the MAC address.
- ptsf-unusable
-
Keyword used to clear the PTSF-unusable condition associated with a neighbor port.
- statistics
-
Keyword used to clear statistics information of the specified port ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
port
Syntax
port port-id [port-id] [ interval seconds] [repeat repeat] [ absolute | rate] [multiclass]
port all-ethernet-rates [interval seconds] [ repeat repeat]
Context
[Tree] (monitor port)
Full Context
monitor port
Description
This command enables port traffic monitoring. The specified port(s) statistical information displays at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified port(s). The subsequent statistical information listed for each interval is displayed as a delta to the previous display.
When the rate is specified, the "rate per second" for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- port-id
-
Specify up to 5 port IDs. Port-IDs are only MLPPP bundles or bundle protection groups when the multiclass is specified.
port-id
slot/mda/port [.channel]
eth-sat-id
esat-id/slot/port
esat
keyword
id
1 to 20
pxc-id
pxc-id.sub-port
pxc
keyword
id
1 to 64
sub-port
a, b
aps-id
aps-group-id[.channel]
aps
keyword
group-id
1 to 64
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
When the absolute is specified, the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
When the rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
- all-ethernet-rates
-
Enables port traffic monitoring and utilization output for all data Ethernet ports enabled in the system, in a table output format.
Platforms
All
Output
The following outputs are examples of port information.
Output ExampleA:ALA-12>monitor# port 2/1/4 interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for Port 2/1/4
===============================================================================
Input Output
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Octets 0 0
Packets 39 175
Errors 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Octets 0 0
Packets 39 175
Errors 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Octets 0 0
Packets 39 175
Errors 0 0
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Octets 0 0
Packets 39 175
Errors 0 0
===============================================================================
A:ALA-12>monitor#
A:ALA-12>monitor# port 2/1/4 interval 3 repeat 3 rate
===============================================================================
Monitor statistics for Port 2/1/4
===============================================================================
Input Output
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Octets 0 0
Packets 39 175
Errors 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Rate)
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
===============================================================================
A:ALA-12>monitor#
===============================================================================
*A:Cpm-A> monitor port bundle-fr-1/1.1
===============================================================================
Monitor statistics for Port bundle-fr-1/1.1
===============================================================================
Input Output
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
--------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
The following output is an example of port Ethernet information.
Output ExampleA:ALA-12>monitor# port all-ethernet-rates interval 3 repeat 100
===============================================================================
Monitor statistics for all Ethernet Port Rates
===============================================================================
Port-Id D Bits Packets Errors Util
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
5/1/1 I 0 0 0 0.00
O 0 0 0 0.00
5/2/1 I 0 0 0 0.00
O 0 0 0 0.00
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
5/1/1 I 0 0 0 0.00
O 0 0 0 0.00
5/2/1 I 0 0 0 0.00
O 0 0 0 0.00
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
5/1/1 I 0 0 0 0.00
O 0 0 0 0.00
5/2/1 I 0 0 0 0.00
O 0 0 0 0.00
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Rate)
-------------------------------------------------------------------------------
5/1/1 I 4286480384 697669 0 43.98
I 4286382080 697653 0 43.98
5/2/1 I 4254070784 692394 0 43.64
I 4253952000 692375 0 43.64
-------------------------------------------------------------------------------
At time t = 12 sec (Mode: Rate)
-------------------------------------------------------------------------------
5/1/1 I 9746288640 1586K 0 99.99
I 9746216960 1586K 0 99.99
5/2/1 I 9746280448 1586K 0 99.99
I 9746167808 1586K 0 99.99
===============================================================================
A:ALA-12>monitor#
port
Syntax
port port-id [port-id] atm [aal-5 | cp cp-id | ilmi | interface-connection | pvc vpi/vci [aal-5 | oam] | pvp vpi [aal-5 | oam | pvt vpi1.vpi2] [interval seconds] [repeat repeat] [absolute | rate]
port port-id [port-id] hw-agg-shaper-sched [interval seconds] [repeat repeat] [absolute | rate]
port port-id [port-id] hw-agg-shaper-sched [interval seconds] [repeat repeat] monitor-threshold
port port-id [port-id] [interval seconds] [repeat repeat] [absolute | rate] [multiclass]
port port-id [port-id] port-scheduler [ interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor port)
Full Context
monitor port
Description
This command enables port traffic monitoring. Various keywords can be used to monitor specific attributes of the ATM port. The specified port(s) statistical information displays at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified port(s). The subsequent statistical information listed for each interval is displayed as a delta to the previous display.
When the rate is specified, the "rate per second" for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- port-id
-
Specifies up to five port IDs. Port-IDs are only be MLPPP bundles or bundle protection groups when the multiclass is specified.
port-id
slot/mda/port [.channel]
aps-id
aps-group-id[.channel]
aps
keyword
group-id
1 to 64
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays the rate-per-second for each statistic, instead of the delta.
- monitor-threshold
-
Displays the exceed count for the port-scheduler under Vport (if specified) or for a physical port.
- multiclass
-
Monitors multiclass statistics.
- port-scheduler
-
Monitors the packet and octet counters for traffic exiting the specified port for the applicable applied port scheduler policy.
- atm
-
Monitors ATM statistics.
- aal-5
-
Monitors the AAL-5 statistics for the port.
- cp-id
-
Monitors ATM connection profile statistics.
- ilmi
-
Monitors ATM ILMI statistics.
- interface-connection
-
Monitors ATM interface connection statistics.
- pvc vpi/vci
-
Monitors ATM PVC statistics.
- pvp vpi
-
Monitors ATM PVP statistics
- pvt vpi1.vpi2
-
Monitors ATM PVT statistics.
- oam
-
Monitors ATM PVC/PVP OAM statistics.
Platforms
All
Output
The following output is an example of port ATM information.
Output ExampleA:ALA-49# monitor port 9/1/1 atm interval 3 repeat 2 absolute
===============================================================================
Monitor ATM statistics for Port 9/1/1
===============================================================================
Input Output
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Octets 0 0
Cells 0 0
Unknown VPI/VCI Cells 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Octets 0 0
Cells 0 0
Unknown VPI/VCI Cells 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Octets 0 0
Cells 0 0
Unknown VPI/VCI Cells 0
===============================================================================
A:ALA-49#
*A:PE1# monitor port 5/1/5 port-scheduler interval 11 repeat 1
===============================================================================
Monitor Port Scheduler statistics for Port 5/1/5
===============================================================================
Forwarded Dropped
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Total
Octets 2177303552 2687166080
Packets 17010184 20993485
Level 1
Octets 1306180608 1936799360
Packets 10204536 15131245
Level 2
Octets 871122944 750366720
Packets 6805648 5862240
Level 3
Octets 0 0
Packets 0 0
Level 4
Octets 0 0
Packets 0 0
Level 5
Octets 0 0
Packets 0 0
Level 6
Octets 0 0
Packets 0 0
Level 7
Octets 0 0
Packets 0 0
Level 8
Octets 0 0
Packets 0 0
-------------------------------------------------------------------------------
At time t = 11 sec (Mode: Delta)
-------------------------------------------------------------------------------
Total
Octets 29900288 36902528
Packets 233596 288301
Level 1
Octets 17937408 26597632
Packets 140136 207794
Level 2
Octets 11962880 10304896
Packets 93460 80507
Level 3
Octets 0 0
Packets 0 0
Level 4
Octets 0 0
Packets 0 0
Level 5
Octets 0 0
Packets 0 0
Level 6
Octets 0 0
Packets 0 0
Level 7
Octets 0 0
Packets 0 0
Level 8
Octets 0 0
Packets 0 0
===============================================================================
*A:PE1#
*A:PE1# monitor port 5/1/5 vport "dslam-3" interval 11 repeat 1 rate
===============================================================================
Monitor Port Scheduler statistics for Port 5/1/5
===============================================================================
Forwarded Dropped
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Total
Octets 2207203840 2724068608
Packets 17243780 21281786
Level 1
Octets 1324118016 1963396992
Packets 10344672 15339039
Level 2
Octets 883085824 760671616
Packets 6899108 5942747
Level 3
Octets 0 0
Packets 0 0
Level 4
Octets 0 0
Packets 0 0
Level 5
Octets 0 0
Packets 0 0
Level 6
Octets 0 0
Packets 0 0
Level 7
Octets 0 0
Packets 0 0
Level 8
Octets 0 0
Packets 0 0
-------------------------------------------------------------------------------
At time t = 11 sec (Mode: Rate)
-------------------------------------------------------------------------------
Total
Octets 3909578 4825079
Packets 30544 37696
Bits 31276624 38600632
Utilization (% of port capacity) 0.36 0.44
Level 1
Octets 2345386 3477723
Packets 18323 27170
Bits 18763088 27821784
Utilization (% of port capacity) 0.21 0.32
Level 2
Octets 1564192 1347356
Packets 12220 10526
Bits 12513536 10778848
Utilization (% of port capacity) 0.14 0.12
Level 3
Octets 0 0
Packets 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
Level 4
Octets 0 0
Packets 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
Level 5
Octets 0 0
Packets 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
Level 6
Octets 0 0
Packets 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
Level 7
Octets 0 0
Packets 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
Level 8
Octets 0 0
Packets 0 0
Bits 0 0
Utilization (% of port capacity) 0.00 0.00
===============================================================================
port
Syntax
port port-id egress network queue-group queue-group-name instance instance-id [ interval seconds] [repeat repeat] [absolute | rate] [arbiter [root | name]]
Context
[Tree] (monitor>qos>arbiter-stats port)
Full Context
monitor qos arbiter-stats port
Description
This command monitors arbiter statistics in an egress port queue group.
Parameters
- port port-id
-
port-id
slot/mda/port [.channel]
eth-sat-id
esat-id/slot/port
esat
keyword
id
1 to 20
pxc-id
pxc-id.sub-port
pxc
keyword
id
1 to 64
sub-port
a, b
- egress network
-
Specifies statistics are for an egress network queue group.
- queue-group queue-group-name
-
Specifies the name of the queue group up to 32 characters.
- instance instance-id
-
Specifies the identification of a specific instance of the queue-group.
- interval seconds
-
Configures the interval for each display in seconds.
- repeat repeat
-
Configures how many times the command is repeated.
- absolute
-
When the absolute keyword is specified, the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
When the rate keyword is specified, the rate-per-second for each statistic is displayed.
- arbiter name
-
Specify the name of the policer control policy arbiter.
- root
-
Specify the root arbiter.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
port
Syntax
port port-id queue-group queue-group-name [ ingress | egress] [interval seconds] [repeat repeat] [ absolute | rate] [access | network] [instance instance-id]
port port-id vport name [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>qos>scheduler-stats port)
Full Context
monitor qos scheduler-stats port
Description
This command enables port traffic monitoring.
Parameters
- port port-id
-
Specifies the port ID.
- queue-group queue-group-name
-
Specifies the name of the queue group up to 32 characters.
- instance instance-id
-
Specifies the identification of a specific instance of the queue-group.
- ingress
-
Specifies statistics are for an ingress queue group.
- egress
-
Specifies statistics are for an egress queue group.
- interval seconds
-
Configures the interval for each display in seconds.
- repeat repeat
-
Configures how many times the command is repeated.
- absolute
-
When the absolute keyword is specified, the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
When the rate keyword is specified, the rate-per-second for each statistic is displayed.
- access
-
Displays scheduler statistics applied on an access port.
- network
-
Displays scheduler statistics applied on a network port.
Platforms
All
port
Syntax
port port-id exp-secondary-shaper shaper-name [interval seconds] [repeat repeat] [absolute | rate]
port port-id vport name [interval seconds] [repeat repeat]
Context
[Tree] (monitor>qos port)
Full Context
monitor qos port
Description
This command monitors expanded secondary shaper statistics.
Parameters
- port-id
-
Specifies the port ID.
- shaper-name
-
Displays statistics for the named exp secondary shaper.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic.
- vport name
-
Displays statistics for the named Vport.
Platforms
All
port
Syntax
port port-id queue-group queue-group-name [ egress] [network] [instance instance-id] [ arbiter {name | root}]
Context
[Tree] (clear>qos>arbiter-stats port)
Full Context
clear qos arbiter-stats port
Description
This command clears the arbiter statistics per port.
Parameters
- port-id
-
Specifies the port ID.
- queue-group-name
-
Specifies the queue group name, up to 32 characters.
- network
-
Clears the egress network queue group statistics.
- instance-id
-
Specifies the ID of a specific instance for the queue group.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
port
Syntax
port port-id queue-group queue-group-name [ingress | egress] [access | network] [instance instance-id] [scheduler scheduler-name]
port port-id vport name [scheduler scheduler-name]
Context
[Tree] (clear>qos>scheduler-stats port)
Full Context
clear qos scheduler-stats port
Description
This command clears the scheduler statistics per port.
Parameters
- port-id
-
Specifies the ID of a specific instance for the queue group.
- queue-group-name
-
Specifies the queue group name, up to 32 characters.
- ingress
-
Clears statistics for the ingress queue group.
- egress
-
Clears statistics for the egress queue group.
- access
-
Clears scheduler statistics applied on an access port.
- network
-
Clears scheduler statistics applied on a network port.
- instance-id
-
Specifies the ID of a specific instance for the queue group.
- name
-
Specifies the Vport name, up to 32 characters.
- scheduler-name
-
Specifies the scheduler name, up to 32 characters.
Platforms
All
port
Syntax
port port-id egress [network] [ queue-group queue-group-name] [instance instance-id] [ arbiter name | root]
Context
[Tree] (show>qos>arbiter-stats port)
Full Context
show qos arbiter-stats port
Description
This command displays the arbiter statistics per port.
Parameters
- port-id
-
Displays information about the specified port.
- network
-
Displays arbiter statistics applied on a network port.
- queue-group-name
-
Specifies the queue group name, up to 32 characters.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
port
Syntax
port port-id network egress queue-group group-name instance instance-id [ detail]
Context
[Tree] (show>qos>policer port)
Full Context
show qos policer port
Description
This command displays the policer statistics per port.
Parameters
- port-id
-
Displays information about the specified port.
- group-name
-
Specifies the queue group name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
port
Syntax
port port-id vport name [scheduler scheduler-name]
Context
[Tree] (show>qos>scheduler-stats port)
Full Context
show qos scheduler-stats port
Description
This command displays the Vport scheduler stats.
Parameters
- port-id
-
Displays information for the specified port.
- name
-
Displays information for the specified Vport.
- scheduler-name
-
Displays information for the specified scheduler-name.
Platforms
All
Output
The following output is an example of Vport scheduler information.
Output Example*A:BNG# show qos scheduler-stats port 1/1/1 vport "dslam1" scheduler "dslam-sched"
===============================================================================
Scheduler Stats
===============================================================================
Scheduler Forwarded Packets Forwarded Octets
-------------------------------------------------------------------------------
Egress Schedulers
dslam-sched 0 0
===============================================================================
*A:BNG#
Vport Scheduler Statistics Field Descriptions describes Vport scheduler statistics output fields.
|
Field |
Description |
|---|---|
|
Scheduler |
The scheduler name |
|
Forwarded Packets |
The number of forwarded packets, as determined by the subscriber ingress scheduler policy |
|
Forwarded Octets |
The number of forwarded octets, as determined by the subscriber ingress scheduler policy |
port-db
port-db
Syntax
port-db sap sap-id
port-db sap sap-id detail
port-db sap sap-id group grp-ipv6-address
port-db sdp sdp-id:vc-id [detail]
port-db sdp sdp-id:vc-id group grp-ipv6-address
Context
[Tree] (show>service>id>mld-snooping port-db)
Full Context
show service id mld-snooping port-db
Description
This command displays MLD snooping information related to a specific SAP.
Platforms
All
Output
The following output is an example of MLD snooping information for a specific SAP.
Output Example*A:rbae_C# show service id 1 mld-snooping port-db sap 1/1/4
===============================================================================
MLD Snooping SAP 1/1/4 Port-DB for service 1
===============================================================================
Group Address
Mode Type From-VPLS Up Time Expires Num MC
Src Stdby
-------------------------------------------------------------------------------
FF04::1
include dynamic local 0d 00:00:19 0s 1
FF04::2
include dynamic local 0d 00:00:18 0s 1
-------------------------------------------------------------------------------
Number of groups: 2
===============================================================================
*A:rbae_C#
*A:rbae_C# show service id 1 mld-snooping port-db sap 1/1/4 detail
===============================================================================
MLD Snooping SAP 1/1/4 Port-DB for service 1
-------------------------------------------------------------------------------
MLD Group FF04::1
-------------------------------------------------------------------------------
Mode : include Type : dynamic
Up Time : 0d 00:00:33 Expires : 0s
Compat Mode : MLD Version 2
V1 Host Expires : 0s :
MVR From-VPLS : local MVR To-SAP : local
MC Standby : no
-------------------------------------------------------
Source Address
Up Time Expires Type Fwd/Blk
-------------------------------------------------------
2011::1
0d 00:00:33 20s dynamic Fwd
-------------------------------------------------------------------------------
MLD Group FF04::2
-------------------------------------------------------------------------------
Mode : include Type : dynamic
Up Time : 0d 00:00:32 Expires : 0s
Compat Mode : MLD Version 2
V1 Host Expires : 0s :
MVR From-VPLS : local MVR To-SAP : local
MC Standby : no
-------------------------------------------------------
Source Address
Up Time Expires Type Fwd/Blk
-------------------------------------------------------
2011::1
0d 00:00:33 20s dynamic Fwd
-------------------------------------------------------------------------------
Number of groups: 2
===============================================================================
*A:rbae_C#
port-db
Syntax
port-db sap sap-id [detail]
port-db sap sap-id group grp-address
port-db sdp sdp-id:vc-id [detail]
port-db sdp sdp-id:vc-id group grp-ip-address
vxlan vtep ip-address vni vni-id
Context
[Tree] (show>service>id>igmp-snooping port-db)
Full Context
show service id igmp-snooping port-db
Description
This command displays information on the IGMP snooping port database for the VPLS service.
Parameters
- grp-ip-address
-
Displays the IGMP snooping port database for a specific multicast group address
- sap-id
-
Displays the IGMP snooping port database for a specific SAP
- sdp-id
-
Displays only IGMP snooping entries associated with the specified mesh SDP or spoke-SDP. For a spoke-SDP, the VC ID must be specified, for a mesh SDP, the VC ID is optional.
- vc-id
-
The virtual circuit ID on the SDP ID for which to display information
- grp-address
-
Displays IGMP snooping statistics matching the specified group address.
- ip-address
-
Displays IGMP snooping statistics matching one particular source within the multicast group.
- vxlan vtep ip-address vni <1..16777215>
-
Displays the IGMP snooping entries associated with a specific VXLAN binding, given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI).
- vni
-
The VXLAN Network Identifier (VNI) for which to display information.
Platforms
All
Output
Output Example*A:ALA-1>show>service>id>snooping# port-db sap 1/1/2
===============================================================================
IGMP Snooping SAP 1/1/2 Port-DB for service 10
===============================================================================
Group Address Mode Type Up Time Expires Num Sources
-------------------------------------------------------------------------------
239.0.0.1 include dynamic 0d 00:04:44 0s 2
Group Address Mode Type From-VPLS Up Time Expires Num Src
-------------------------------------------------------------------------------
239.0.0.1 include dynamic Local 0d 00:04:44 0s 2
-------------------------------------------------------------------------------
Number of groups: 1
===============================================================================
*A:ALA-1>show>service>id>snooping#
*A:ALA-1>show>service>id>snooping# port-db sap 1/1/2 detail
===============================================================================
IGMP Snooping SAP 1/1/2 Port-DB for service 10
===============================================================================
IGMP Group 239.0.0.1
-------------------------------------------------------------------------------
Mode : include Type : dynamic
Up Time : 0d 00:04:57 Expires : 0s
Compat Mode : IGMP Version 3
V1 Host Expires : 0s V2 Host Expires : 0s
-------------------------------------------------------
Source Address Up Time Expires Type Fwd/Blk
-------------------------------------------------------
1.1.1.1 0d 00:04:57 20s dynamic Fwd
1.1.1.2 0d 00:04:57 20s dynamic Fwd
-------------------------------------------------------------------------------
Number of groups: 1
===============================================================================
*A:ALA-1>show>service>id>snooping#
IGMP Snooping Port Database Fields describes the show output fields.
|
Label |
Description |
|---|---|
|
Group Address |
The IP multicast group address for which this entry contains information. |
|
Mode |
Specifies the type of membership reports received on the interface for the group. In the include mode, reception of packets sent to the specified multicast address is requested only from those IP source addresses listed in the source-list parameter of the IGMP membership report. In the exclude mode, reception of packets sent to the specified multicast address is requested from all IP source addresses except those listed in the source-list parameter. |
|
Type |
Indicates how this group entry was learned. If this group entry was learned by IGMP, the value is set to dynamic. For statically configured groups, the value is set to static. |
|
Compatibility mode |
Specifies the IGMP mode. This is used for routers to be compatible with older-version routers. IGMPv3 hosts must operate in Version 1 and Version 2 compatibility modes. IGMPv3 hosts must keep state per local interface regarding the compatibility mode of each attached network. A host's compatibility mode is determined from the host compatibility mode variable which can be in one of three states: IGMPv1, IGMPv2 or IGMPv3. This variable is kept per interface and is dependent on the version of general queries heard on that interface as well as the older-version querier present timers for the interface. |
|
V1 host expires |
The time remaining until the local router will assume that there are no longer any IGMP Version 1 members on the IP subnet attached to this interface. Upon hearing any IGMPv1 membership report, this value is reset to the group membership timer. While this time remaining is non-zero, the local router ignores any IGMPv2 leave messages for this group that it receives on this interface. |
|
V2 host expires |
The time remaining until the local router will assume that there are no longer any IGMP Version 2 members on the IP subnet attached to this interface. Upon hearing any IGMPv2 membership report, this value is reset to the group membership timer. While this time remaining is non-zero, the local router ignores any IGMPv3 leave messages for this group that it receives on this interface. |
|
Source address |
The source address for which this entry contains information. |
|
Up Time |
The time since the source group entry was created. |
|
Expires |
The amount of time remaining before this entry will be aged out. |
|
Number of sources |
Indicates the number of IGMP group and source specific queries received on this SAP. |
|
Forwarding/Blocking |
Indicates whether this entry is on the forward list or block list. |
|
Number of groups |
Indicates the number of groups configured for this SAP. |
port-db
Syntax
port-db sap sap-id [group grp-ip-address]
port-db sap sap-id group grp-ip-address source src-ip-address
port-db sdp sdp-id:vc-id [group grp-ip-address]
port-db sdp sdp-id:vc-id group grp-ip-address source src-ip-address
port-db [group grp-ip-address] vxlan vtep ip-address vni vni-id
port-db group grp-ip-address source src-ip-address vxlan vtep ip-address vni vni-id
Context
[Tree] (clear>service>id>igmp-snooping port-db)
Full Context
clear service id igmp-snooping port-db
Description
This command clears the information on the IGMP snooping port database for the VPLS service.
Parameters
- sap-id
-
Clears IGMP snooping statistics matching the specified SAP ID and optional encapsulation value
- sdp-id
-
Clears only IGMP snooping entries associated with the specified mesh SDP or spoke-SDP. For a spoke-SDP, the VC ID must be specified, for a mesh SDP, the VC ID is optional.
- vc-id
-
Clears information for the specified virtual circuit ID on the SDP ID
- grp-ip-address
-
Clears IGMP snooping statistics matching the specified group address
- src-ip-address
-
Clears IGMP snooping statistics matching the specified particular source
- vxlan vtep ip-address vni <1..16777215>
-
Clears the IGMP snooping statistics associated with a specific VXLAN destination given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI).
- vni-id
-
Displays information for the specified VXLAN Network Identifier (VNI)
Platforms
All
port-db
Syntax
port-db sap sap-id [group grp-ip-address]
port-db sap sap-id group grp-ip-address source src-ip-address
port-db sdp sdp-id:vc-id [group grp-ip-address]
port-db sdp sdp-id:vc-id group grp-ip-address source src-ip-address
port-db [group grp-ip-address] vxlan vtep ip-address vni vni-id
port-db group grp-ip-address source src-ip-address vxlan vtep ip-address vni vni-id
Context
[Tree] (clear>service>id>mld-snooping port-db)
Full Context
clear service id mld-snooping port-db
Description
This command clears MLD snooping port-db group data.
Parameters
- sap-id
-
Clears IGMP snooping statistics matching the specified SAP ID and optional encapsulation value
- sdp-id
-
Clears only IGMP snooping entries associated with the specified mesh SDP or spoke-SDP. For a spoke-SDP, the VC ID must be specified, for a mesh SDP, the VC ID is optional.
- vc-id
-
Clears information for the specified virtual circuit ID on the SDP ID
- grp-ip-address
-
Clears IGMP snooping statistics matching the specified group address
- src-ip-address
-
Clears IGMP snooping statistics matching the specified particular source
- vxlan vtep ip-address vni <1..16777215>
-
Clears the IGMP snooping statistics associated with a specific VXLAN destination given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI).
- vni-id
-
Displays information for the specified VXLAN Network Identifier (VNI)
Platforms
All
port-forwarding-action
port-forwarding-action
Syntax
port-forwarding-action
Context
[Tree] (tools>perform>nat port-forwarding-action)
Full Context
tools perform nat port-forwarding-action
Description
This command displays NAT port forwarding actions.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
port-forwarding-entries
port-forwarding-entries
Syntax
port-forwarding-entries
Context
[Tree] (show>service>nat port-forwarding-entries)
Full Context
show service nat port-forwarding-entries
Description
This command displays port forwarding entries.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of this command.
Output Example*A:SR12_PPPOE# show service nat port-forwarding-entries
===============================================================================
NAT port forwarding entries
===============================================================================
Subscriber
iRtr iAddress prot iPort type
oRtr oAddress persist-id oPort expiry
===============================================================================
100 10.2.3.4 tcp 666 classic-lsn-sub
Base 10.0.0.6 N/A 666 N/A
100 10.2.3.4 udp 666 classic-lsn-sub
Base 10.0.0.6 N/A 666 N/A
-------------------------------------------------------------------------------
No. of entries: 2
===============================================================================
*A:SR12_PPPOE#
port-list
port-list
Syntax
port-list [port-list-name]
port-list port-list-name references
Context
[Tree] (show>filter>match-list port-list)
Full Context
show filter match-list port-list
Description
This command displays TCP/UDP/SCTP port values or ranges for match criteria in IPv4 and IPv6 ACL and CPM filter policies.
Parameters
- port-list-name
-
A string of up to 32 characters of printable ASCII characters. If special characters are used, the string must be enclosed within double quotes.
- references
-
Displays the filter policies, policy entries and source/destination/port match type per entry referring to this match list.
Platforms
All
port-list
Syntax
port-list
port-list port-list-name [association]
Context
[Tree] (show>qos>match-list port-list)
Full Context
show qos match-list port-list
Description
This command displays the list of configured QoS port lists or the details of a specific QoS port list together with the network QoS policies in which it is used and the entry number within that policy.
Parameters
- port-list-name
-
Displays a port list, up to 32 characters of printable ASCII characters. If special characters are used, the string must be enclosed within double quotes.
- association
-
Displays the network QoS policy and entry number in which the specified port list is used.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of QoS port list information. Output Fields: show qos match-list port-list describes the output fields.
Output Example*A:PE# show qos match-list port-list
===============================================================================
QoS Match Port List
===============================================================================
Port List Name Description Num Ports/Ranges
-------------------------------------------------------------------------------
portlist1 2
portlist2 2
-------------------------------------------------------------------------------
No. of Port-List: 2
===============================================================================
*A:PE#
*A:PE# show qos match-list port-list "portlist1"
===============================================================================
QoS Match Port List
===============================================================================
Port List Name : portlist1
Description : (Not Specified)
-------------------------------------------------------------------------------
Ports/Ranges
-------------------------------------------------------------------------------
80 90-100
-------------------------------------------------------------------------------
No. of Ports/Ranges : 2
-------------------------------------------------------------------------------
===============================================================================
*A:PE#
*A:PE# show qos match-list port-list "portlist1" association
===============================================================================
QoS Match IP Prefix List
===============================================================================
Port List Name : portlist1
Description : (Not Specified)
-------------------------------------------------------------------------------
Ports/Ranges
-------------------------------------------------------------------------------
80 90-100
-------------------------------------------------------------------------------
No. of Ports/Ranges : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Association
-------------------------------------------------------------------------------
QoS Policy ID Criteria Entry
-------------------------------------------------------------------------------
10 (network-egress) 10 (destination-port)
-------------------------------------------------------------------------------
===============================================================================
|
Label |
Description |
|---|---|
|
Port List Name |
Displays the port list name. |
|
Description |
Displays the port list description. |
|
Num Ports/Range |
Displays the number of ports or range of ports. |
|
No. of Port-List |
Displays the number of port lists. |
|
QoS Policy ID |
Displays the QoS policy ID. |
port-map
port-map
Syntax
port-map [client-map-id]
Context
[Tree] (show>system>satellite>eth-sat port-map)
[Tree] (show>system>satellite>tdm-sat port-map)
Full Context
show system satellite eth-sat port-map
show system satellite tdm-sat port-map
Description
This command displays information about configured satellites port maps.
Parameters
- client-map-id
-
Specifies the client map to display. If a client port is associated with a resilient secondary uplink, a second line shows the current secondary uplink association.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
- show system satellite eth-sat port-map
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
- show system satellite tdm-sat port-map
Output
The following output is an example of TDM satellite port map information.
Output ExampleA:admin@Dut-A# show system satellite eth-sat 1 port-map
===============================================================================
Satellite Port Mapping Information
===============================================================================
Client Port Adm Oper Uplink Port Adm Oper Host Port Adm Oper Act
-------------------------------------------------------------------------------
esat-1/1/1 Down Down esat-1/1/u4 Up Up 2/1/2 Up Up Y
esat-1/1/u2 Up Up 1/1/2 Up Up N
esat-1/1/2 Down Down esat-1/1/u4 Up Up 2/1/2 Up Up Y
esat-1/1/u1 Up Up 1/1/1 Up Up N
esat-1/1/3 Down Down esat-1/1/u4 Up Up 2/1/2 Up Up Y
esat-1/1/u1 Up Up 1/1/1 Up Up N
esat-1/1/4 Down Down esat-1/1/u4 Up Up 2/1/2 Up Up Y
esat-1/1/u2 Up Up 1/1/2 Up Up N
port-policy
port-policy
Syntax
port-policy
port-policy policy-name
port-policy policy-name associations
Context
[Tree] (show port-policy)
Full Context
show port-policy
Description
This command displays port policy information.
Parameters
- policy-name
-
Specifies the port policy name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
port-queues
port-queues
Syntax
port-queues queue-depth [queue queue-id]
Context
[Tree] (clear>port port-queues)
Full Context
clear port port-queues
Description
This command clears the port queues and queue depth.
Parameters
- queue-depth
-
Clears the queue depth.
- queue-id
-
Specifies the queue ID.
Platforms
All
port-queues
Syntax
port-queues queue queue-id
port-queues queue-depth [queue queue-id]
Context
[Tree] (show>port port-queues)
Full Context
show port port-queues
Description
This command displays port queues, queue override, and queue depth information.
Parameters
- queue-depth
-
Displays queue depth information for the specified queue group queue.
- queue-id
-
Specifies the queue ID.
Platforms
All
port-recorder
port-recorder
Syntax
port-recorder detail [flow-count flows] [ byte-count kbytes] [isa mda-id /esa-vm-id] url file-url
port-recorder status [isa mda-id/esa-vm-id]
port-recorder top granularity [ max-count max-count] [isa mda-id]
Context
[Tree] (tools>dump>app-assure>group port-recorder)
Full Context
tools dump application-assurance group port-recorder
Description
This command saves the port recorded by the tool into a file. The port-recorder is configured using debug commands.
Parameters
- flow-count flows
-
Match ports with flow count greater than the specified value.
- bytes-count kbytes
-
Match ports with bytes count greater than the specified value.
- status
-
Displays the current status of the port-recorder with current-time, start-time, stop-time, sample-rates as well as number of bytes and flows for UDP and TCP traffic on the specified AA ISA card. The port-recorder is configured using debug commands.
- top
-
Displays by bytes or flows the top ports recorded by the tool on a particular AA ISA.
- mda-id/esa-vm-id
-
Specifies the AA ISA.
- file-url
-
Specifies the URL for the file to direct the port-recorder output to.
- granularity
-
Specifies if the output is sorted by bytes or flows.
- max-count
-
Specifies the maximum number of values to display.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
port-scheduler
port-scheduler
Syntax
port-scheduler [interval seconds] [ repeat repeat] [absolute| rate]
Context
[Tree] (monitor>port port-scheduler)
Full Context
monitor port port-scheduler
Description
This command monitors port scheduler statistics.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
port-scheduler
Syntax
port-scheduler statistics
Context
[Tree] (clear>port port-scheduler)
Full Context
clear port port-scheduler
Description
This command clears port scheduler statistics.
Parameters
- statistics
-
Clears port scheduler statistics.
Platforms
All
port-scheduler
Syntax
port-scheduler statistics
Context
[Tree] (show>lag port-scheduler)
Full Context
show lag port-scheduler
Description
This command displays port scheduler policy information applied to the LAG.
Parameters
- statistics
-
Displays statistics for the port scheduler policy applied to the LAG.
Platforms
All
port-scheduler
Syntax
port-scheduler statistics
Context
[Tree] (show>port port-scheduler)
Full Context
show port port-scheduler
Description
This command displays port schedule policy information applied to the port.
Parameters
- statistics
-
Displays port schedule policy statistics.
Platforms
All
port-scheduler-policy
port-scheduler-policy
Syntax
port-scheduler-policy [port-scheduler-policy-name] [ association]
port-scheduler-policy port-scheduler-policy-name network-policy network-queue-policy-name
port-scheduler-policy port-scheduler-policy-name sap-egress policy-id
port-scheduler-policy port-scheduler-policy-name scheduler-policy scheduler-policy-name
port-scheduler-policy port-scheduler-policy-name scheduler-policy scheduler-policy-name sap-egress policy-id
Context
[Tree] (show>qos port-scheduler-policy)
Full Context
show qos port-scheduler-policy
Description
This command displays port-scheduler policy information
Parameters
- port-scheduler-policy-name
-
Displays information for the specified existing port scheduler policy.
- association
-
Displays associations related to the specified port scheduler policy.
- network-policy network-queue-policy-name
-
Displays information for the specified existing network queue policy.
- sap-egress policy-id
-
Displays information for the specified existing SAP egress policy.
- scheduler-policy scheduler-policy-name
-
Displays information for the specified existing scheduler policy.
Platforms
All
Output
The following output is an example of QoS port scheduler policy information, and Show QoS Port Scheduler Output Fields describes the QoS port scheduler policy fields.
Output Example*A:Dut-R# show qos port-scheduler-policy p1
===============================================================================
QoS Port Scheduler Policy
===============================================================================
Policy-Name : p1
HQOS Algorithm : default
Max Rate : max Last changed : 05/21/2007 10:39:15
Lvl1 PIR : max Lvl1 CIR : max
Lvl2 PIR : max Lvl2 CIR : max
Lvl3 PIR : max Lvl3 CIR : max
Lvl4 PIR : max Lvl4 CIR : max
Lvl5 PIR : max Lvl5 CIR : max
Lvl6 PIR : max Lvl6 CIR : max
Lvl7 PIR : max Lvl7 CIR : max
Lvl8 PIR : max Lvl8 CIR : max
Orphan Lvl : default Orphan Weight : default
Orphan CIR-Lvl : default Orphan CIR-Weight : default
===============================================================================
QoS Port Scheduler Policy
===============================================================================
Policy-Name : p1
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
- Port : 5/1/1
===============================================================================
*A:Dut-R#
The following configuration displays dist-lag-rate-shared and percent-rate for level, group and max-rate in a port-scheduler-policy.
*B:vineshDut-A>config>qos>port-sched-plcy# info
----------------------------------------------
dist-lag-rate-shared
max-rate percent 30.00
group "test" create
percent-rate 20.00 cir 20.00
exit
level 1 percent-rate 10.00 percent-cir 10.00
level 2 percent-rate 20.00 percent-cir 20.00
level 3 percent-rate 30.00 percent-cir 30.00
level 4 percent-rate 40.00 percent-cir 40.00
level 5 percent-rate 50.00 percent-cir 50.00
level 6 percent-rate 60.00 percent-cir 60.00
level 7 percent-rate 70.00 percent-cir 70.00
level 8 percent-rate 80.00 percent-cir 80.00
Overrides
*B:vineshDut-A>config>port# info
----------------------------------------------
ethernet
mode access
egress-scheduler-policy "psp2"
egress-scheduler-override create
max-rate percent 50.00
level 1 percent-rate 10.00 percent-cir 10.00
level 2 percent-rate 20.00 percent-cir 20.00
level 3 percent-rate 30.00 percent-cir 30.00
level 4 percent-rate 40.00 percent-cir 40.00
level 5 percent-rate 50.00 percent-cir 50.00
level 6 percent-rate 60.00 percent-cir 60.00
level 7 percent-rate 70.00 percent-cir 70.00
level 8 percent-rate 80.00 percent-cir 80.00
exit
autonegotiate limited
exit
no shutdown
----------------------------------------------
The following output is an example of port-scheduler-policy Dist Lag Rate and percent parameters.
*B:vineshDut-A>config>port# /show qos port-scheduler-policy "psp2"
===============================================================================
QoS Port Scheduler Policy
===============================================================================
Policy-Name : psp2
Description : (Not Specified)
HQOS Algorithm : default
Max Rate : max Max Rate Percent : 30.00
Dist LAG Rate : True Last changed : 07/16/2014 21:31:51
Group : test
Group PIR : max Group CIR : max
Group PIR Percent : 20.00 Group CIR Percent : 20.00
Lvl1 PIR : max Lvl1 CIR : max
Lvl1 PIR Percent : 10.00 Lvl1 CIR Percent : 10.00
Lvl2 PIR : max Lvl2 CIR : max
Lvl2 PIR Percent : 20.00 Lvl2 CIR Percent : 20.00
Lvl3 PIR : max Lvl3 CIR : max
Lvl3 PIR Percent : 30.00 Lvl3 CIR Percent : 30.00
Lvl4 PIR : max Lvl4 CIR : max
Lvl4 PIR Percent : 40.00 Lvl4 CIR Percent : 40.00
Lvl5 PIR : max Lvl5 CIR : max
Lvl5 PIR Percent : 50.00 Lvl5 CIR Percent : 50.00
Lvl6 PIR : max Lvl6 CIR : max
Lvl6 PIR Percent : 60.00 Lvl6 CIR Percent : 60.00
Lvl7 PIR : max Lvl7 CIR : max
Lvl7 PIR Percent : 70.00 Lvl7 CIR Percent : 70.00
Lvl8 PIR : max Lvl8 CIR : max
Lvl8 PIR Percent : 80.00 Lvl8 CIR Percent : 80.00
Orphan Lvl : default Orphan Weight : default
Orphan CIR-Lvl : default Orphan CIR-Weight : default
===============================================================================
Part of show port Output
-------------------------------------------------------------------------------
Egr Port Sched Override
-------------------------------------------------------------------------------
Max Rate : max* Max Rate Percent : 50.00
Lvl1 PIR : max* Lvl1 CIR : max*
Lvl1 PIR Percent : 10.00 Lvl1 CIR Percent : 10.00
Lvl2 PIR : max* Lvl2 CIR : max*
Lvl2 PIR Percent : 20.00 Lvl2 CIR Percent : 20.00
Lvl3 PIR : max* Lvl3 CIR : max*
Lvl3 PIR Percent : 30.00 Lvl3 CIR Percent : 30.00
Lvl4 PIR : max* Lvl4 CIR : max*
Lvl4 PIR Percent : 40.00 Lvl4 CIR Percent : 40.00
Lvl5 PIR : max* Lvl5 CIR : max*
Lvl5 PIR Percent : 50.00 Lvl5 CIR Percent : 50.00
Lvl6 PIR : max* Lvl6 CIR : max*
Lvl6 PIR Percent : 60.00 Lvl6 CIR Percent : 60.00
Lvl7 PIR : max* Lvl7 CIR : max*
Lvl7 PIR Percent : 70.00 Lvl7 CIR Percent : 70.00
Lvl8 PIR : max* Lvl8 CIR : max*
Lvl8 PIR Percent : 80.00 Lvl8 CIR Percent : 80.00
* means the value is inherited
-------------------------------------------------------------------------------
|
Label |
Description |
|---|---|
|
Policy Name |
Displays the port scheduler policy name. |
|
HQOS Algorithm |
Displays the port scheduler H-QoS algorithm used to calculate the operational rates for the children connected to the port scheduler. |
|
Max Rate |
Displays the explicit maximum frame-based bandwidth limit of this port scheduler. |
|
Lvlx PIR |
Displays the total bandwidth limit, PIR, for the specified priority level. |
|
Lvlx CIR |
Displays the within-CIR bandwidth limit for the specified priority level. |
|
Orphan Lvl |
Displays above-CIR port priority of orphaned queues and scheduler. |
|
Orphan Weight |
Displays the weight of orphaned queues and schedulers that are above-CIR. |
|
Orphan CIR-Lvl |
Displays the port priority of orphaned queues and schedulers that are within-CIR. |
|
Orphan CIR-Weight |
Displays the weight of orphaned queues and schedulers that are within-CIR. |
|
Associations |
Displays associations related to the specified port scheduler policy. |
|
Mode |
Displays the port scheduler policy mode (STRICT, RR, WRR, WDRR). |
|
Accounting |
Displays whether the accounting mode is frame-based or packet-based |
|
Last Changed |
Displays the last time the configuration changed. |
|
Queue # |
Displays the weight of the queue if configured. |
port-topology
port-topology
Syntax
port-topology [uni-dir]
Context
[Tree] (show>system port-topology)
Full Context
show system port-topology
Description
This command generates a listing of the internal connections within the router. These include connections to satellite ports. Use of the uni-dir keyword will list each connection twice; once for each direction.
Parameters
- uni-dir
-
Specifies to list each direction as a separate row.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of port topology information.
Output Example*A:Dut-A# show system port-topology
===============================================================================
Port Topology
===============================================================================
Port Far-end
Id Port Id
-------------------------------------------------------------------------------
esat-1/1/u1 1/1/1
esat-1/1/u2 1/1/2
esat-1/1/u3 1/2/1
esat-1/1/u4 1/2/2
esat-20/1/u1 1/1/3
esat-20/1/u2 1/2/3
esat-20/1/u3 2/1/3
esat-20/1/u4 2/2/3
-------------------------------------------------------------------------------
No. of Number of port-topology associations: 8
===============================================================================
port-tree
port-tree
Syntax
port-tree port-id
Context
[Tree] (show port-tree)
Full Context
show port-tree
Description
This command displays the tree for SONET/SDH or TDM ports/channels WAN PHY mode (xgig wan) Ethernet ports.
Parameters
- port-id
-
Specifies the physical port ID.
Platforms
All
Output
The following output is an example of port information, and Output Fields: show port-tree <port-id> describes the output fields.
Output Example: show port-tree <port-id>A:ALA-48>config# show port-tree 7/1/1
ifIndex type, sonet-sdh-index (* = provisioned)
=========== =======================================
119570432 Port, N/A *
656441345 DS3, none *
656441405 DS1, 1 *
656441430 DS1, 2
656441455 DS1, 3
656441480 DS1, 4
656441505 DS1, 5
656441530 DS1, 6
656441555 DS1, 7
656441580 DS1, 8
656441605 DS1, 9
656441630 DS1, 10
656441655 DS1, 11
656441680 DS1, 12
656441705 DS1, 13
656441730 DS1, 14
656441755 DS1, 15
656441780 DS1, 16
656441805 DS1, 17
656441830 DS1, 18
656441855 DS1, 19
656441880 DS1, 20
656441905 DS1, 21
656441930 DS1, 22
656441980 DS1, 24
656442005 DS1, 25
656442030 DS1, 26
656442055 DS1, 27
656442080 DS1, 28
A:ALA-48>config#
|
Label |
Description |
|---|---|
|
IfIndex |
Displays the interface index number which reflects its initialization sequence. |
|
type |
Specifies the type. |
|
sonet-sdh-index |
Specifies the sonet-sdh-index. |
|
* |
When an asterisk (*) is displayed after the sonet-sdh-index, the port/channel is provisioned. |
port-xc
port-xc
Syntax
port-xc [pxc pxc-id]
Context
[Tree] (show>port-xc port-xc)
Full Context
show port-xc
Description
This command displays information about Port Cross-Connect (PXC) information.
Parameters
- pxc-id
-
Specifies the PXC ID.
Platforms
All
Output
The following output is an example of PXC information, and Output Fields: port-xc describes the output fields.
Output Example*A:cses-B04# show port-xc
===============================================================================
Port Cross-Connect Information
===============================================================================
PXC Admin Oper Port Description
Id State State Id
-------------------------------------------------------------------------------
1 Up Up 1/x1/1/c1/1 fpe based pw-ports
2 Up Up 1/x1/1/c2/1 (Not Specified)
3 Up Up 1/x1/1/c3/1 (Not Specified)
4 Up Up 1/x1/1/m1/1 (Not Specified)
5 Up Up 1/x1/1/m1/1 (Not Specified)
-------------------------------------------------------------------------------
No. of PXCs: 5
===============================================================================
*A:cses-B04#
show port 1/1/m1/1
===============================================================================
Anchor
===============================================================================
Description : Anchor
Interface : 1/1/m1/1
FP Number : 1 MAC Chip Number : 1
Licensed : Yes
Admin State : down
Oper State : up
IfIndex : 1610903569
Last State Change : 12/07/2020 07:02:21
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Ing. Acc. Wt. : 50 Egr. Acc. Wt. : 50
Ing. Net. Wt. : 50 Egr. Net. Wt. : 50
===============================================================================
|
Label |
Description |
|---|---|
|
PXC Id |
The port cross-connect identifier |
|
Admin State |
The administrative state of the port |
|
Oper State |
The operational state of the port |
|
Port Id |
The port ID |
|
Description |
The PXC ID description |
|
Interface |
The port ID |
|
MAC Chip Number |
The MAC chip number for this port |
|
Licensed |
Yes — The port is licensed and can be used in a service configuration. No — The port is unlicensed and may not be used |
|
IFIndex |
Displays the interface's index number which reflects its initialization sequence. |
|
Last State Change |
Displays the last time the operational status of the port changed state. |
|
Ing. Pool % Rate |
The increment or decrement of the active bandwidth associated with the ingress port. This active bandwidth affects the amount of ingress buffer space managed by the port. |
|
Egr. Pool % Rate |
The increment or decrement of the active bandwidth associated with the egress port. This active bandwidth affects the amount of egress buffer space managed by the port. |
positive-app-id
positive-app-id
Syntax
positive-app-id
Context
[Tree] (tools>dump>app-assure>group>ipassist positive-app-id)
Full Context
tools dump application-assurance group ip-identification-assist positive-app-id
Description
This command dumps the statistics related to IP identification assist for top applications using IP addresses learned from successfully classified traffic using the AA application database.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
Use this command to dump the statistics.
tools dump application-assurance group "1" ip-identification-assist positive-app-id isa "1/1"===============================================================================
Application-Assurance ip-identification-assist positive-app-id:
===============================================================================
group 1
ip-identification-assist no shutdown
passive-dns enabled
positive-app-id enabled
--------------------------------------------------------------------------------
isa 1/1
--------------------------------------------------------------------------------
Application Name IPs in cache IPs added IPs updated IP lookups found Parent Application Name
---------------------------------- ------------ ---------------------- ---------------------- ---------------------- ----------------------------------
"Application1" 0 0 0 0 "ParentApplication1"
"Application2" 0 0 0 0 "ParentApplication1"
"Application3" 0 0 0 0 "ParentApplication1"
"Application4" 0 0 0 0 "ParentApplication1"
"Application5" 0 0 0 0 "ParentApplication2"
"Application6" 0 0 0 0 "ParentApplication3"
"Application7" 0 0 0 0 "ParentApplication3"
"Application8" 0 0 0 0 "ParentApplication2"
"Application9" 0 0 0 0 "ParentApplication4"
"Application10" 0 0 0 0 "ParentApplication5"
"Application11" 0 0 0 0 "ParentApplication6"
"Application12" 0 0 0 0 "ParentApplication7"
"Application13" 0 0 0 0 "ParentApplication2"
"Application14" 0 0 0 0 "ParentApplication3"
---------------------------------- ------------ ---------------------- ---------------------- ----------------------------------
TOTAL (14 applications) 0 0 0 0
===============================================================================post-policer-mapping
post-policer-mapping
Syntax
post-policer-mapping [post-policer-name] [ association | detail]
Context
[Tree] (show>qos post-policer-mapping)
Full Context
show qos post-policer-mapping
Description
This command displays information about post-policer mapping policies. Omitting the policy name will list all policies.
Parameters
- post-policer-name
-
Specifies the name of the post-policer mapping policy, up to 32 characters.
- association
-
Displays the entities associated with the post-policer mapping policy.
- detail
-
Displays the detailed information for the post-policer mapping policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
Output
This section shows output example for post-policer mapping.
Output Example*A:PE# show qos post-policer-mapping
===============================================================================
Post Policer Mapping Summary
===============================================================================
Policy Description
-------------------------------------------------------------------------------
ppm1 Map FC EF/exceed to BE/out
-------------------------------------------------------------------------------
Policies
===============================================================================
*A:PE#
*A:PE# show qos post-policer-mapping detail
===============================================================================
Post Policer Mapping Information
===============================================================================
Policy Name : ppm1
Description : Map FC EF/exceed to BE/out
-------------------------------------------------------------------------------
Post Policer Mapping Information
-------------------------------------------------------------------------------
FC Profile Mapped-FC Mapped-Profile
-------------------------------------------------------------------------------
ef Exceed be Out
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Sap Egress Associations
-------------------------------------------------------------------------------
Policy ID
-------------------------------------------------------------------------------
10
-------------------------------------------------------------------------------
===============================================================================
power-management
power-management
Syntax
power-management [zone]
Context
[Tree] (show>chassis power-management)
Full Context
show chassis power-management
Description
This command shows the power management requirement and utilization information.
Parameters
- zone
-
The chassis power zone.
Platforms
7750 SR-12e, 7750 SR-s, 7950 XRS
Output
The following output is an example of power management information, and Output Fields: show chassis power-management describes the output fields.
Output Example: show chassis power-management*A:Dut-A# show chassis power-management
===============================================================================
Chassis Information
===============================================================================
Power Management Information
Power Management Mode : basic
Power Safety Level : 100%
Power Safety Alert : 0 watts
Power-Zone : 1
Number of PEQs : 12
PEQ number : 1
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : shutdown
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0116
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : down
Operational state : down
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 2
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : (Not Specified)
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1249G0022
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : unprovisioned
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 3
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0141
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 4
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1249G0201
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 5
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0123
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 6
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0061
Manufacture date : 12182012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 7
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARB01
CLEI code : IPUPAJHUAA
Serial number : NS13226A310
Manufacture date : 06042013
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 82-0532-02
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 8
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0152
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 9
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0122
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 10
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0146
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 11
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1249G0202
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
PEQ number : 12
PEQ Equipped Type : apeq-dc-2000
PEQ Provisioned Type : apeq-dc-2000
Status : up
Input Feed Status : input B down
Hardware Data
Part number : 3HE07114AARA01
CLEI code : IPUPAJHUAA
Serial number : NS1250G0115
Manufacture date : 12202012
Manufacturing deviations : (Not Specified)
Manufacturing assembly number : 8205320107
Administrative state : up
Operational state : up
Time of last boot : 2014/01/07 11:01:44
Current alarm state : alarm active
===============================================================================
PCM number : 1
PCM Equipped Type : not detected
PCM Provisioned Type : (not provisioned)
PCM number : 2
PCM Equipped Type : not detected)
PCM Provisioned Type : (not provisioned)
PCM number : 3
PCM Equipped Type : not detected
PCM Provisioned Type : (not provisioned)
PCM number : 4
PCM Equipped Type : not detected
PCM Provisioned Type : (Not provisioned)
PCM number : 5
PCM Equipped Type : not detected
PCM Provisioned Type : (Not provisioned)
PCM number : 6
PCM Equipped Type : indeterminate
PCM Provisioned Type : (Not provisioned)
PCM number : 7
PCM Equipped Type : indeterminate
PCM Provisioned Type : (Not provisioned)
PCM number : 8
PCM Equipped Type : indeterminate
PCM Provisioned Type : (Not provisioned)
PCM number : 9
PCM Equipped Type : indeterminate
PCM Provisioned Type : dual-pcm
PCM number : 10
PCM Equipped Type : quad-pcm
PCM Provisioned Type : (Not provisioned)
Power-Zone : 1
Status : up
Input Feed Status : power to all inputs
Hardware Data
Part number : Sim Part#
CLEI code : Sim CLEI
Serial number : peq-12
Manufacture date : 01012003
Manufacturing deviations : Sim MfgDeviation peq-12
Manufacturing assembly number : 01-2345-67
PCM number : 11
PCM Equipped Type : quad-pcm
PCM Provisioned Type : quad-pcm
Power-Zone : 1
Status : up
Input Feed Status : power to all inputs
Hardware Data
Part number : Sim Part#
CLEI code : Sim CLEI
Serial number : peq-12
Manufacture date : 01012003
Manufacturing deviations : Sim MfgDeviation peq-12
Manufacturing assembly number : 01-2345-67
PCM number : 12
PCM Equipped Type : quad-pcm
PCM Provisioned Type : quad-pcm
Power-Zone : 1
Status : up
Input Feed Status : power to all inputs
Hardware Data
Part number : Sim Part#
CLEI code : Sim CLEI
Serial number : peq-12
Manufacture date : 01012003
Manufacturing deviations : Sim MfgDeviation peq-12
Manufacturing assembly number : 01-2345-67
-------------------------------------------------------------------------------
Chassis Control Module (CCM) Information
CCM Slot : A
Equipped : yes
Hardware Data
Part number : Sim Part#
CLEI code : Sim CLEI
Serial number : ccm-1
Manufacture date : 01012003
Manufacturing deviations : Sim MfgDeviation ccm-1
Manufacturing assembly number : 01-2345-67
Administrative state : up
Operational state : up
Temperature : -128C
Temperature threshold : 75C
Time of last boot : N/A
Current alarm state : alarm cleared
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 52.80 Volts (09/10/2014 18:09:58)
Current : 52.80 Volts
Peak : 52.80 Volts (09/10/2014 18:09:58)
Wattage
Minimum : 20.00 Watts (09/10/2014 18:09:58)
Current : 20.00 Watts
Peak : 20.00 Watts (09/10/2014 18:09:58)
Max Required : 22.00 Watts
Amperage
Minimum : 0.38 Amps (09/10/2014 18:09:58)
Current : 0.38 Amps
Peak : 0.38 Amps (09/10/2014 18:09:58)
CCM Slot : B
Equipped : yes
Hardware Data
Part number :
CLEI code :
Serial number :
Manufacture date :
Manufacturing deviations : (Not Specified)
Manufacturing assembly number :
Administrative state : up
Operational state : up
Temperature : 0C
Temperature threshold : 75C
Time of last boot : N/A
Current alarm state : alarm cleared
Hardware Resources (Power-Zone 1)
Voltage
Minimum : 0.00 Volts (N/A)
Current : 0.00 Volts
Peak : 0.00 Volts (N/A)
Wattage
Minimum : 0.00 Watts (N/A)
Current : 0.00 Watts
Peak : 0.00 Watts (N/A)
Max Required : 0.00 Watts
Amperage
Minimum : 0.00 Amps (N/A)
Current : 0.00 Amps
Peak : 0.00 Amps (N/A)
===============================================================================
Chassis 2 Detail
===============================================================================
|
Label |
Description |
|---|---|
|
Power Management Mode |
Specifies the configured power management mode: None, Basic, or Advanced. |
|
Power Safety Level |
Specifies the configured Power Safety Level, which is a percentage of the worst case power consumption level. |
|
Power Safety Alert |
Specifies the configured power level in watts, which causes the system to raise an alarm if the available power level drops below a set level. |
|
Power-Zone |
Specifies the chassis power zone. |
|
Number of PEQs |
Specifies the total number of APEQs installed. |
|
PEQ number: |
Specifies the APEQ to which the information is associated |
|
PEQ Equipped Type |
Specifies the APEQ type installed. |
|
PEQ Provisioned Type |
Specifies the APEQ type provisioned. |
|
Status |
Specifies the APEQ status. |
|
Input Feed Status |
Specifies the feed status. This field indicates that power is detected on all inputs or lists the inputs where no power is detected. |
|
PCM Equipped Type |
Indicates the type of PCM installed in the specified PIM or PCM slot:
Some PCMs can only be verified for presence based on power available at the associated APEQ. These are indicated as indeterminate. When the equipped type is quad-pcm, the additional fields of Power-Zone, Status, and Input Feed Status and Hardware Data are displayed. |
|
PCM Provisioned Type |
One of the following types:
For a given PCM number, if the equipped type is not detected and the provisioned type is not specified, the PCM is not displayed. |
|
Hardware Data: |
|
|
Part number |
The APEQ part number. |
|
CLEI code |
The APEQ CLEI code. |
|
Serial number |
The APEQ serial number. |
|
Manufacture date |
The date the APEQ was manufactured. |
|
Manufacturing deviations |
Specifies any manufacturing deviations. |
|
Manufacturing assembly number |
The APEQ assembly number. |
|
Administrative state |
Specifies the administrative state of the APEQ. |
|
Operational state |
Specifies the operational state of the APEQ. |
|
Time of last boot |
Indicates the time stamp of the last system restart. |
|
Current alarm state |
Indicates the current alarm state. |
power-module
power-module
Syntax
power-module [power-module-id] [detail]
Context
[Tree] (show>chassis>power-shelf power-module)
Full Context
show chassis power-shelf power-module
Description
This command displays the power-module.
Parameters
- power-module-id
-
Specifies the power module ID.
- detail
-
Displays detailed power module information.
Platforms
7750 SR-s
Output
The following output is an example of a power module
Output Example: show chassis power-shelf power-moduleA:DUT-A# show chassis power-shelf 1 power-module
===============================================================================
Power Shelf Summary
===============================================================================
Slot Provisioned Type Admin Operational Zone Input Output
Equipped Type (if diff) State State Mode
-------------------------------------------------------------------------------
1 ps-a10-shelf-dc up up 1 80A on
===============================================================================
===============================================================================
Power Module Summary
===============================================================================
Slot Provisioned Type Admin Operational Input Zone
Equipped Type (if diff) State State A B
-------------------------------------------------------------------------------
1 ps-a-dc-6000 up up Y Y 1
2 ps-a-dc-6000 up up Y Y 1
===============================================================================
A:DUT-A# show chassis power-shelf 2 power-module
===============================================================================
Power Shelf Summary
===============================================================================
Slot Provisioned Type Admin Operational Zone Input Output
Equipped Type (if diff) State State Mode
-------------------------------------------------------------------------------
2 ps-b10-shelf-ac/hv up up 1 N/A on
===============================================================================
===============================================================================
Power Module Summary
===============================================================================
Slot Provisioned Type Admin Operational Input Zone
Equipped Type (if diff) State State A B
-------------------------------------------------------------------------------
1 ps-b-ac/hv-6000 up up Y Y 1
2 ps-b-ac/hv-6000 up down N N 1
5 ps-b-ac/hv-6000 up down N N 1
===============================================================================
A:DUT-A#
A:DUT-A# show chassis power-shelf 2 power-module 1 detail
===============================================================================
Power Shelf Summary
===============================================================================
Slot Provisioned Type Admin Operational Zone Input Output
Equipped Type (if diff) State State Mode
-------------------------------------------------------------------------------
2 ps-b10-shelf-ac/hv up up 1 N/A on
===============================================================================
===============================================================================
Power Module 1 detail
===============================================================================
Slot Provisioned Type Admin Operational Input Zone
Equipped Type (if diff) State State A B
-------------------------------------------------------------------------------
1 ps-b-ac/hv-6000 up up Y Y 1
Power Module Specific Data
Output Status : ok
Hardware Data
Platform type : N/A
Part number : 3HE11183AARA0101
CLEI code : GA-PSUHVDC
Serial number : NS1736W0096
Manufacture date : 09152017
Manufacturing deviations : For Internal Use Only
Manufacturing assembly number :
Time of last boot : 2020/07/07 11:13:07
Current alarm state : alarm cleared
===============================================================================
A:DUT-A# show chassis power-shelf 2 detail
===============================================================================
Power Shelf 2 detail
===============================================================================
Slot Provisioned Type Admin Operational Zone Input Output
Equipped Type (if diff) State State Mode
-------------------------------------------------------------------------------
2 ps-b10-shelf-ac/hv up up 1 N/A on
Power Shelf Specific Data
Description : (Not Specified)
Controller serial number : NS1745W0143
Hardware Data
Platform type : N/A
Part number : 3HE11179AARA
CLEI code : T-REX-HVDC
Serial number : NS1747W0004
Manufacture date : 12212017
Manufacturing deviations : For Internal Use Only
Manufacturing assembly number :
Time of last boot : 2020/07/07 11:13:07
Current alarm state : alarm cleared
Hardware Data
Platform type : N/A
Part number : 3HE11181AARA
CLEI code : M-SHELFCON
Serial number : NS1745W0143
Manufacture date : 11152017
Manufacturing deviations : For Internal Use Only
Manufacturing assembly number :
Time of last boot : 2020/07/07 11:13:07
Current alarm state : alarm cleared
===============================================================================
A:DUT-A#
power-module
Syntax
power-module power-module-id
Context
[Tree] (clear>chassis>power-shelf power-module)
Full Context
clear chassis power-shelf power-module
Description
This command toggles the output power of the power module, turning it off for two seconds then on. This procedure can be used to clear an ovSD (output voltage shutdown) fault. The only alternative method to clear the ovSD fault is to physically remove the power module from the power shelf and re-insert. Running this command does not clear the latched faults.
Parameters
- power-module-id
-
Specifies the power-module ID.
Platforms
7750 SR-s
power-module
Syntax
power-module power-module-id telemetry
Context
[Tree] (tools>dump>power-shelf power-module)
Full Context
tools dump power-shelf power-module
Description
This command displays the specified power module information, telemetry, and fault data. When a fault is no longer active it remains marked as a latched fault for tracking purposes until manually cleared.
Parameters
- power-module-id
-
Displays information about the specified power-module ID.
- telemetry
-
Displays telemetry and fault data for the specified power module.
Platforms
7750 SR-s
power-module
Syntax
power-module power-module-id clear-faults
Context
[Tree] (tools>perform>power-shelf power-module)
Full Context
tools perform power-shelf power-module
Description
This command clears all the latched faults for inactive faults.
Parameters
- power-module-id
-
Specifies power-module ID.
- clear-faults
-
Clears fault conditions against the specified power module.
Platforms
7750 SR-s
power-shelf
power-shelf
Syntax
power-shelf [power-shelf-id] [ detail] [chassis chassis-name]
Context
[Tree] (show>chassis power-shelf)
Full Context
show chassis power-shelf
Description
This command displays the power shelf.
Parameters
- power-shelf-id
-
Specifies the power shelf ID.
- detail
-
Displays detailed power shelf information.
- chassis-name
-
Specifies the chassis name, up to 256 characters maximum.
Platforms
7750 SR-s
Output
The following output is an example of power shelves
Output Example: show chassis power-shelfA:DUT-A# show chassis power-shelf
===============================================================================
Power Shelf Summary
===============================================================================
Slot Provisioned Type Admin Operational Zone Input Output
Equipped Type (if diff) State State Mode
-------------------------------------------------------------------------------
1 ps-a10-shelf-dc up up 1 80A on
2 ps-b10-shelf-ac/hv up up 1 N/A on
===============================================================================
power-shelf
Syntax
power-shelf power-shelf-id
Context
[Tree] (clear>chassis power-shelf)
Full Context
clear chassis power-shelf
Description
Commands in this context clear power-shelf components.
Parameters
- power-shelf-id
-
Specifies power-shelf ID.
Platforms
7750 SR-s
power-shelf
Syntax
power-shelf power-shelf-id
Context
[Tree] (tools>dump power-shelf)
Full Context
tools dump power-shelf
Description
Commands in this context display power-shelf information.
Parameters
- power-shelf-id
-
Displays information about the specified power-shelf.
Platforms
7750 SR-s
power-shelf
Syntax
power-shelf power-shelf-id
Context
[Tree] (tools>perform power-shelf)
Full Context
tools perform power-shelf
Description
Commands in this context configure power-shelf parameters.
Parameters
- power-shelf-id
-
Specifies the power-shelf ID.
Platforms
7750 SR-s
ppp
ppp
Syntax
ppp
Context
[Tree] (show>service>id ppp)
Full Context
show service id ppp
Description
Commands in this context display service PPP information for the specified service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
ppp
Syntax
ppp
Context
[Tree] (tools>perform>subscr-mgmt>loc-user-db ppp)
Full Context
tools perform subscriber-mgmt local-user-db ppp
Description
This command provides the tools to control PPPoE entries in the local user database.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
ppp
Syntax
ppp
Context
[Tree] (show>call-trace ppp)
Full Context
show call-trace ppp
Description
Commands in this context display Point-to-Point Protocols (PPP) call trace information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
ppp-policy
ppp-policy
Syntax
ppp-policy [ppp-policy-name [association]]
Context
[Tree] (show>subscr-mgmt ppp-policy)
Full Context
show subscriber-mgmt ppp-policy
Description
This command displays PPP policy information.
Parameters
- ppp-policy-name
-
Specifies an existing PPP policy.
- association
-
Displays the object the PPP policy is associated.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PPP policy information and Show Subscriber Management PPP Policy Field Descriptions describes the field descriptions.
|
Label |
Description |
|---|---|
|
Description |
Specifies the description. |
|
Last Mgmt Change |
Specifies the date and time of the last management change. |
|
PPP-mtu |
Specifies the configured maximum PPP MTU size. |
|
Force PPP-mtu >1492 |
Specifies if PPPoE MRU negotiations greater than 1492 bytes are enabled without receiving a "PPP-Max-Payload" tag in the PADI/PADR client message (Yes, No). |
|
Keepalive Interval |
Specifies the keepalive interval, in seconds. |
|
Keepalive Multiplier |
Specifies the keepalive multiplier value. |
|
Disable AC-Cookies |
Specifies to disable AC cookies (Yes, No). |
|
PADO Delay |
Specifies the PADO delay value, in milliseconds. |
|
Max Sessions-Per-Mac |
Specifies the maximum number of sessions with the same client MAC address and active on the same SAP or MSAP. |
|
Reply-On-PADT |
Specifies to reply on PADT (Yes, No). |
|
Allow Same CID |
Specifies to allow the same Circuit ID for multiple PPPoE sessions with the same client MAC address and active on the same SAP when using the internal DHCPv4 client for IPv4 address allocation (Yes, No). |
|
Re-establish Session |
Specifies if a PPPoE session can be re-established upon receiving a PADR from a PPPoE client that previously disconnected without sending a PADT and for which a session is still active in the BNG (PADR, Disabled). |
|
PPP-Authentication |
Specifies the PPP Authentication method (PAP, CHAP, pref-PAP or pref-CHAP). |
|
PPP-CHAP Challenge |
Specifies the minimum and maximum length of a PPP CHAP Challenge (in bytes). |
|
PPP-Init-Delay (ms) |
Specifies the delay in milliseconds for sending an LCP configure request after the discovery phase. |
|
IPCP negotiate subnet |
Specifies if IPCP subnet negotiation is enabled (Yes, No). |
|
Unique SIDs-Per-SAP |
Specifies the unique SIDs per-SAP (disabled, per-capture-sap, per-msap). |
|
Reject-Disabled-Ncp |
Specifies if an LCP protocol reject is sent for an unconfigured NCP (Yes, No). |
|
Ignore-Magic-Num |
Specifies if the LCP peer magic number should be ignored (Yes, No). |
|
Session Timeout |
Specifies the session timeout value in seconds (default = unlimited). |
|
SID Allocation |
Specifies the PPPoE Session ID allocation method (sequential, random). |
|
PADO AC-Name |
Specifies the AC name used in PADO messages. |
|
Default username |
Specifies the default username for PAP or CHAP authentication. |
|
Default password |
Specifies the default PAP password (Specified, Not specified). |
|
Accept MRRU |
Specifies to accept MRRU (true, false). |
|
Request short sequence nr. |
Specifies to request short sequence numbers (true, false). |
|
Endpoint class |
Specifies the endpoint class (null, ipv4-address or mac-address). |
|
Endpoint address |
Specifies the endpoint IPv4 or mac address. |
# /show subscriber-mgmt ppp-policy "ppp-policy-1"
===============================================================================
PPP Policy "ppp-policy-1"
===============================================================================
Description : (Not Specified)
Last Mgmt Change : 01/09/2020 16:40:19
PPP-mtu : N/A Force PPP-mtu >1492 : No
Keepalive Interval : 30s Keepalive Multiplier : 3
Disable AC-Cookies : No PADO Delay : 0msec
Max Sessions-Per-Mac : 1 Reply-On-PADT : No
Allow Same CID : No Re-establish Session : Disabled
PPP-Authentication : pref-CHAP PPP-CHAP Challenge : 32 - 64
PPP-Init-Delay (ms) : 0 IPCP negotiate subnet: No
Unique SIDs-Per-SAP : disabled Reject-Disabled-Ncp : No
Ignore-Magic-Num : No Session Timeout : unlimited
SID Allocation : sequential
PADO AC-Name : (Not Specified)
Default username : (Not Specified)
Default password : (Not Specified)
-------------------------------------------------------------------------------
PPP Custom Options
-------------------------------------------------------------------------------
Protocol Number Value
-------------------------------------------------------------------------------
No options configured.
-------------------------------------------------------------------------------
MLPPP
-------------------------------------------------------------------------------
Accept MRRU : false
Request short sequence nr. : false
Endpoint class : null
Endpoint address : (Not Specified)
-------------------------------------------------------------------------------
ppp-policy
Syntax
ppp-policy [ppp-policy-name [association]]
Context
[Tree] (show>subscr-mgmt ppp-policy)
Full Context
show subscriber-mgmt ppp-policy
Description
This command displays PPP policy information.
Parameters
- ppp-policy-name
-
Specifies an existing PPP policy.
- association
-
Displays the object the PPP policy is associated.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PPP policy information and Show Subscriber Management PPP Policy Field Descriptions describes the field descriptions.
|
Label |
Description |
|---|---|
|
Description |
Specifies the description. |
|
Last Mgmt Change |
Specifies the date and time of the last management change. |
|
PPP-mtu |
Specifies the configured maximum PPP MTU size. |
|
Force PPP-mtu >1492 |
Specifies if PPPoE MRU negotiations greater than 1492 bytes are enabled without receiving a "PPP-Max-Payload" tag in the PADI/PADR client message (Yes, No). |
|
Keepalive Interval |
Specifies the keepalive interval, in seconds. |
|
Keepalive Multiplier |
Specifies the keepalive multiplier value. |
|
Disable AC-Cookies |
Specifies to disable AC cookies (Yes, No). |
|
PADO Delay |
Specifies the PADO delay value, in milliseconds. |
|
Max Sessions-Per-Mac |
Specifies the maximum number of sessions with the same client MAC address and active on the same SAP or MSAP. |
|
Reply-On-PADT |
Specifies to reply on PADT (Yes, No). |
|
Allow Same CID |
Specifies to allow the same Circuit ID for multiple PPPoE sessions with the same client MAC address and active on the same SAP when using the internal DHCPv4 client for IPv4 address allocation (Yes, No). |
|
Re-establish Session |
Specifies if a PPPoE session can be re-established upon receiving a PADR from a PPPoE client that previously disconnected without sending a PADT and for which a session is still active in the BNG (PADR, Disabled). |
|
Max Sessions-Per-Cid |
Specifies the maximum number of sessions with the same Agent Circuit ID that can be active on the same SAP or MSAP. |
|
Allow No CID |
Specifies whether PPPoE sessions without an Agent Circuit ID to be established on a SAP or MSAP with a max-sessions-per-cid limit configured (Yes, No). |
|
PPP-Authentication |
Specifies the PPP Authentication method (PAP, CHAP, pref-PAP or pref-CHAP). |
|
PPP-CHAP Challenge |
Specifies the minimum and maximum length of a PPP CHAP Challenge (in bytes). |
|
PPP-Init-Delay (ms) |
Specifies the delay in milliseconds for sending an LCP configure request after the discovery phase. |
|
IPCP negotiate subnet |
Specifies if IPCP subnet negotiation is enabled (Yes, No). |
|
Unique SIDs-Per-SAP |
Specifies the unique SIDs per-SAP (disabled, per-capture-sap, per-msap). |
|
Reject-Disabled-Ncp |
Specifies if an LCP protocol reject is sent for an unconfigured NCP (Yes, No). |
|
Ignore-Magic-Num |
Specifies if the LCP peer magic number should be ignored (Yes, No). |
|
Session Timeout |
Specifies the session timeout value in seconds (default = unlimited). |
|
SID Allocation |
Specifies the PPPoE Session ID allocation method (sequential, random). |
|
PADO AC-Name |
Specifies the AC name used in PADO messages. |
|
Default username |
Specifies the default username for PAP or CHAP authentication. |
|
Default password |
Specifies the default PAP password (Specified, Not specified). |
|
Accept MRRU |
Specifies to accept MRRU (true, false). |
|
Request short sequence nr. |
Specifies to request short sequence numbers (true, false). |
|
Endpoint class |
Specifies the endpoint class (null, ipv4-address or mac-address). |
|
Endpoint address |
Specifies the endpoint IPv4 or mac address. |
# /show subscriber-mgmt ppp-policy "ppp-policy-1"
===============================================================================
PPP Policy "ppp-policy-1"
===============================================================================
Description : (Not Specified)
Last Mgmt Change : 01/09/2020 16:40:19
PPP-mtu : N/A Force PPP-mtu >1492 : No
Keepalive Interval : 30s Keepalive Multiplier : 3
Disable AC-Cookies : No PADO Delay : 0msec
Max Sessions-Per-Mac : 1 Reply-On-PADT : No
Allow Same CID : No Re-establish Session : Disabled
Max Sessions-Per-Cid : 10
Allow No CID : No
PPP-Authentication : pref-CHAP PPP-CHAP Challenge : 32 - 64
PPP-Init-Delay (ms) : 0 IPCP negotiate subnet: No
Unique SIDs-Per-SAP : disabled Reject-Disabled-Ncp : No
Ignore-Magic-Num : No Session Timeout : unlimited
SID Allocation : sequential
PADO AC-Name : (Not Specified)
Default username : (Not Specified)
Default password : (Not Specified)
-------------------------------------------------------------------------------
PPP Custom Options
-------------------------------------------------------------------------------
Protocol Number Value
-------------------------------------------------------------------------------
No options configured.
-------------------------------------------------------------------------------
MLPPP
-------------------------------------------------------------------------------
Accept MRRU : false
Request short sequence nr. : false
Endpoint class : null
Endpoint address : (Not Specified)
-------------------------------------------------------------------------------
pppoe
pppoe
Syntax
pppoe
Context
[Tree] (show>service>id pppoe)
Full Context
show service id pppoe
Description
Commands in this context display PPPoE information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pppoe
Syntax
pppoe
Context
[Tree] (clear>call-trace pppoe)
Full Context
clear call-trace pppoe
Description
Commands in this context clear the PPPoE job.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pppoe
Syntax
pppoe
Context
[Tree] (clear>service>id pppoe)
Full Context
clear service id pppoe
Description
Commands in this context clear PPPoE-related data for the specified service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pppoe-client
pppoe-client
Syntax
pppoe-client [brg-id brg-ident]
pppoe-client [brg-id brg-ident] [ detail]
pppoe-client [brg-id brg-ident] [ statistics]
Context
[Tree] (show>subscr-mgmt>vrgw>brg pppoe-client)
Full Context
show subscriber-mgmt vrgw brg pppoe-client
Description
This command displays information of PPPoE clients started by the vRGW.
Parameters
- brg-ident
-
Specifies the string identifying the BRG, up to 32 characters maximum.
- detail
-
Displays detailed PPPoE client information.
- statistics
-
Displays PPPoE client statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PPPoE client information.
Output ExampleNode# show subscriber-mgmt vrgw brg pppoe-client
================================================================
PPPoE Clients
================================================================
Id
Svc-Id MAC PPPoE-Sid Up-Time
IP-Address IPv6-Prefix
----------------------------------------------------------------
00:0c:29:00:00:10
20 00:0c:29:00:00:10 1 0d 00:00:05
10.255.1.16 2001:db8:101::/64
----------------------------------------------------------------
No. of PPPoE Clients: 1
================================================================
Node# show subscriber-mgmt vrgw brg pppoe-client detail
===============================================================================
PPPoE Clients detail
===============================================================================
Id : 00:0c:29:00:00:10
Service Id : 20
MAC Address : 00:0c:29:00:00:10
Up Time : 0d 00:00:27
Policy : clnt_plcy
PPPoE Session Id : 1
Service Name : (Not Specified)
AC MAC : 08:06:ff:00:00:02
AC Name : BNG
LCP State : opened
IPCP State : opened
IPv6CP State : opened
Local Magic Num : 201366211
Remote Magic Num : 374038276
Remote MRU : 1492
PPP User-Name : 00:0c:29:00:00:10
PPP Auth-Protocol : none
IP Address : 10.255.1.16
Primary DNS : 1.1.1.1
Secondary DNS : 1.1.2.2
Primary NBNS : 2.2.1.1
Secondary NBNS : 2.2.2.2
IPv6 Intf Id : 02:0c:29:ff:fe:00:00:10
IPv6 Prefix : 2001:db8:101::/64
Prefix Timeout : 86375
Primary IPv6 DNS : 2001:db8:dddd:1::1
Secondary IPv6 DNS : 2001:db8:dddd:2::1
-------------------------------------------------------------------------------
No. of PPPoE Clients: 1
===============================================================================
Node# show subscriber-mgmt vrgw brg pppoe-client statistics
==================================================
PPPoE Clients statistics
==================================================
Id : 00:0c:29:00:00:10
Packet Type Received Transmitted
PADI - 1
PADO 1 -
PADR - 1
PADS 1 -
PADT 0 0
Session 9 9
LCP Echo Request
(since restart) 0 21
LCP Echo Reply
(since restart) 21 0
RS - 1
RA 1 -
DHCP6 Info - 1
DHCP6 Reply 1 -
--------------------------------------------------
Rx Dropped : 0
--------------------------------------------------
No. of PPPoE Clients: 1
==================================================
pppoe-client
Syntax
pppoe-client
Context
[Tree] (tools>perform>subscr-mgmt>brg pppoe-client)
Full Context
tools perform subscriber-mgmt vrgw brg pppoe-client
Description
This command enables tools for controlling PPPoE clients in a BRG.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pppoe-client-policy
pppoe-client-policy
Syntax
pppoe-client-policy [name]
pppoe-client name associations
Context
[Tree] (show>subscr-mgmt pppoe-client-policy)
Full Context
show subscriber-mgmt pppoe-client-policy
Description
This command displays PPPoE client policy information.
Parameters
- name
-
Specifies the PPPoE client policy name, up to 32 characters.
- associations
-
Displays information associated with the policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
prefix-ext-stats
prefix-ext-stats
Syntax
prefix-ext-stats ipv6-address/prefix-length
prefix-ext-stats pool pool-name
Context
[Tree] (show>router>dhcp6>server prefix-ext-stats)
Full Context
show router dhcp6 local-dhcp-server prefix-ext-stats
Description
This command displays extended statistics per DHCPv6 prefix in local DHCPv6 server.
The following statistics are included in output:
-
The number of stable leases in the prefix
-
The number of provisioned /64 address block in the prefix
-
The number of used /64 address block in the prefix
-
The number of free /64 address block in the prefix
-
The percentage of used address (with /64 address block)
-
The percentage of free address (with /64 address block)
For each statistic (except for Provisioned Addresses), there is current value and peak value, peak value is the highest value since prefix creation or last reset via command clear>router rt-id>dhcp6>local-dhcp-server svr-name>prefix-ext-stats.
When the pool parameter is used, the statistics of each prefix in the pool are displayed.
Parameters
- ipv6-address/prefix-length
-
Specifies the IPv6 prefix.
- pool-name
-
The name of DHCPv6 local server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of prefix extended stats information.
Output Exampleshow router 500 dhcp6 local-dhcp-server "d6" prefix-ext-stats 2001:ABCD::/62
===============================================================================
Extended statistics for prefix 2001:ABCD::/62
===============================================================================
Current Peak TimeStamp
-------------------------------------------------------------------------------
Local:
Failover Oper State Active
Stable Leases 0 0 01/07/2013 19:54:52
Provisioned Blks 4
Used Blks 0 0 01/07/2013 19:54:52
Free Blks 4 4 01/07/2013 19:54:52
Used Pct 0 0 01/07/2013 19:54:52
Free Pct 100 100 01/07/2013 19:54:52
Last Reset Time 01/07/2013 19:54:52
-------------------------------------------------------------------------------
Number of entries 1
===============================================================================
Prefix Extended Statistics Field Descriptions describes extended prefix statistics output fields.
|
Field |
Description |
|---|---|
|
Current |
The current extended prefix statistics |
|
Peak |
The peak value since the last reset |
|
TimeStamp |
The date and time of the last reset |
|
Failover Oper State |
The operational state of the DHCP specified prefix |
|
Stable Leases |
The number of stable leases |
|
Provisioned Blks |
The number of provisioned blocks |
|
Used Blks |
The number of used blocks |
|
Free Blks |
The number of free blocks |
|
Used Pct |
The percentage of extended prefixes in use |
|
Free Pct |
The percentage of free prefixes in use |
|
Last Reset Time |
The date and time of the last reset |
|
Number of entries |
The total number of entries |
prefix-ext-stats
Syntax
prefix-ext-stats ipv6-address/prefix-length
prefix-ext-stats pool pool-name
Context
[Tree] (clear>router>dhcp6>server prefix-ext-stats)
Full Context
clear router dhcp6 local-dhcp-server prefix-ext-stats
Description
This command reset the begin time of peak values in output of the show router rt-id dhcp6 local-dhcp-server svr-name prefix-ext-stats command/
Parameters
- ipv6-address/prefix-length
-
Clears information about the specified IPv6 prefix.
- pool-name
-
Clears information about the specified local DHCPv6 server pool name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
prefix-label
prefix-label
Syntax
prefix-label
Context
[Tree] (show>router>bgp prefix-label)
Full Context
show router bgp prefix-label
Description
This command displays BGP Prefix label information.
Platforms
All
prefix-sids
prefix-sids
Syntax
prefix-sids [ipv4-unicast| ipv6-unicast | ipv4-multicast | ipv6-multicast | mt mt-id-number] [ ip-prefix[/prefix-length]] [sid sid] [ adv-router system-id | hostname] [srms | no-srms] [algo algo-id]
Context
[Tree] (show>router>isis prefix-sids)
Full Context
show router isis prefix-sids
Description
This command displays IS-IS prefix SIDs.
Parameters
- ipv4-unicast
-
Displays IPv4 unicast parameters.
- ipv6-unicast
-
Displays IPv6 unicast parameters.
- ipv4-multicast
-
Displays IPv4 multicast parameters.
- ipv6-multicast
-
Displays IPv6 multicast parameters.
- mt-id-number
-
Displays multi-topology parameters.
- ip-prefix[/prefix-length]
-
Displays information about the specified IP prefix and length.
- sid
-
Displays information for the specific segment identifier.
- system-id | hostname
-
Displays information for the specific IS-IS advertising router. Host name up to 38 characters.
- srms
-
Displays parameters filtered for segment routing mapping server.
- no-srms
-
Displays parameters filtered for no segment routing mapping server.
- algo-id
-
Displays information for the specified algorithm.
Platforms
All
Output
The following outputs are examples of prefix SID information, and IS-IS Prefix SIDs Output Fields describes the output fields.
Output Example*A:Dut-B#
*A:Dut-B# show router isis 0 prefix-sids
===============================================================================
Rtr Base ISIS Instance 0 Prefix/SID Table
===============================================================================
Prefix SID Lvl/Typ SRMS AdvRtr
Algo MT Flags
-------------------------------------------------------------------------------
10.20.1.1/32 1 2/Int. N Dut-A
0 0 NnP
10.20.1.1/32 11 2/Int. N Dut-A
128 0 NnP
10.20.1.2/32 2 1/Int. N Dut-B
0 0 NnP
10.20.1.2/32 12 1/Int. N Dut-B
128 0 NnP
10.20.1.2/32 2 2/Int. N Dut-B
0 0 NnP
10.20.1.2/32 12 2/Int. N Dut-B
128 0 NnP
10.20.1.3/32 3 2/Int. N Dut-C
0 0 NnP
10.20.1.3/32 13 2/Int. N Dut-C
128 0 NnP
10.20.1.4/32 4 2/Int. N Dut-B
0 0 RNnP
10.20.1.4/32 14 2/Int. N Dut-B
128 0 RNnP
10.20.1.4/32 4 1/Int. N Dut-D
0 0 NnP
10.20.1.4/32 14 1/Int. N Dut-D
128 0 NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 12 (4 unique)
-------------------------------------------------------------------------------
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
Flags: R = Re-advertisement
N = Node-SID
nP = no penultimate hop POP
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
===============================================================================
*A:Dut-B# show router isis 0 prefix-sids algo 128
===============================================================================
Rtr Base ISIS Instance 0 Prefix/SID Table
===============================================================================
Prefix SID Lvl/Typ SRMS AdvRtr
Algo MT Flags
-------------------------------------------------------------------------------
10.20.1.1/32 11 2/Int. N Dut-A
128 0 NnP
10.20.1.2/32 12 1/Int. N Dut-B
128 0 NnP
10.20.1.2/32 12 2/Int. N Dut-B
128 0 NnP
10.20.1.3/32 13 2/Int. N Dut-C
128 0 NnP
10.20.1.4/32 14 2/Int. N Dut-B
128 0 RNnP
10.20.1.4/32 14 1/Int. N Dut-D
128 0 NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 6 (4 unique)
-------------------------------------------------------------------------------
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
Flags: R = Re-advertisement
N = Node-SID
nP = no penultimate hop POP
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
===============================================================================
A:Dut-A>config>router# show router isis prefix-sids
===============================================================================
Rtr Base ISIS Instance 0 Prefix/SID Table
===============================================================================
Prefix SID Lvl/Typ SRMS AdvRtr
Shared MT Flags
-------------------------------------------------------------------------------
1.0.0.1/32 4001 1/Int. N Dut-A
Yes 0 NnP
1.0.0.1/32 4001 2/Int. N Dut-A
Yes 0 NnP
10.20.0.1/32 301 1/Int. N Dut-A
No 0 NnP
10.20.0.1/32 301 2/Int. N Dut-A
No 0 NnP
10.20.0.2/32 402 1/Int. N Dut-B
N.A. 0 NnP
10.20.0.2/32 402 2/Int. N Dut-B
N.A. 0 NnP
3ffe::100:1/128 6001 1/Int. N Dut-A
Yes 0 NnP
3ffe::100:1/128 6001 2/Int. N Dut-A
Yes 0 NnP
3ffe::a14:1/128 401 1/Int. N Dut-A
No 0 NnP
3ffe::a14:1/128 401 2/Int. N Dut-A
No 0 NnP
3ffe::a14:2/128 402 1/Int. N Dut-B
N.A. 0 NnP
3ffe::a14:2/128 402 2/Int. N Dut-B
N.A. 0 NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 12 (6 unique)
-------------------------------------------------------------------------------
SRMS: Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
Flags: R = Re-advertisement
N = Node-SID
nP = no penultimate hop POP
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
Shared: Yes = local shared Node-SID
No = not a local shared Node-SID
N.A. = not applicable for Remote prefix-sid
===============================================================================
*A:Dut-C#
|
Label |
Description |
|---|---|
|
Prefix |
Displays the IP prefix for the SID |
|
SID |
Displays the SID value |
|
Adv-Rtr |
Displays the IP address of the advertised router |
|
SRMS |
Displays whether the prefix SID is advertised by the SR mapping server (Y or N) or selected to be programmed (S) |
|
Flags |
Displays the SID flags |
|
No. of Prefix/SIDs |
Displays the number of Prefix/SIDs |
prefix-sids
Syntax
prefix-sids [ip-prefix[/prefix-length]] [ sid sid] [adv-router router-id] [ algo algo-id]
Context
[Tree] (show>router>ospf prefix-sids)
Full Context
show router ospf prefix-sids
Description
This command displays OSPF prefix SIDs.
Parameters
- ip-prefix[/prefix-length]
-
Displays information about the specified IP prefix and length, up to 64 characters.
- sid
-
Displays information for the specific segment identifier.
- router-id
-
Displays information for the specific advertising router identified by its router identifier.
- algo-id
-
Displays the algorithm identifier.
Platforms
All
Output
The following outputs are examples of OSPF prefix SIDs information, and OSPF Prefix SIDs Output Fields describes the output fields.
Output Example*A:Dut-F# show router ospf prefix-sids
========================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
========================================================================
Prefix Area RtType SID
Adv-Rtr Flags
------------------------------------------------------------------------
1.0.11.1/32 0.0.0.0 INTER-AREA 4
10.20.1.2 NnP
1.0.11.1/32 0.0.0.1 INTRA-AREA 4
10.20.1.1 NnP
1.0.11.1/32 0.0.0.1 INTRA-AREA 999
10.20.1.3 NnPB
1.0.22.2/32 0.0.0.0 INTER-AREA 5
10.20.1.2 NnPA
1.0.22.2/32 0.0.0.1 INTRA-AREA 5
10.20.1.2 NnP
1.0.22.2/32 0.0.0.1 INTRA-AREA 996
10.20.1.6 NnPB
1.0.33.3/32 0.0.0.0 INTER-AREA 0
10.20.1.2 NnP
1.0.33.3/32 0.0.0.1 INTRA-AREA 0
10.20.1.3 NnP
1.0.33.3/32 0.0.0.1 INTRA-AREA 998
10.20.1.1 NnPB
1.0.44.4/32 0.0.0.0 INTRA-AREA 1
10.20.1.4 NnP
1.0.44.4/32 0.0.0.0 INTRA-AREA 994
10.20.1.5 NnPB
1.0.44.4/32 0.0.0.1 INTER-AREA 1
10.20.1.2 NnP
1.0.55.5/32 0.0.0.0 INTRA-AREA 2
10.20.1.5 NnP
1.0.55.5/32 0.0.0.0 INTRA-AREA 995
10.20.1.4 NnPB
1.0.55.5/32 0.0.0.1 INTER-AREA 2
10.20.1.2 NnP
1.0.66.6/32 0.0.0.0 INTER-AREA 3
10.20.1.2 NnP
1.0.66.6/32 0.0.0.1 INTRA-AREA 3
10.20.1.6 NnP
1.0.66.6/32 0.0.0.1 INTRA-AREA 997
10.20.1.2 NnPB
10.20.1.1/32 0.0.0.0 INTER-AREA 10
10.20.1.2 NnP
10.20.1.1/32 0.0.0.1 INTRA-AREA 10
10.20.1.1 NnP
10.20.1.2/32 0.0.0.0 INTRA-AREA 11
10.20.1.2 NnP
10.20.1.2/32 0.0.0.1 INTER-AREA 11
10.20.1.2 NnPA
10.20.1.3/32 0.0.0.0 INTER-AREA 6
10.20.1.2 NnP
10.20.1.3/32 0.0.0.1 INTRA-AREA 6
10.20.1.3 NnP
10.20.1.4/32 0.0.0.0 INTRA-AREA 7
10.20.1.4 NnP
10.20.1.4/32 0.0.0.1 INTER-AREA 7
10.20.1.2 NnP
10.20.1.5/32 0.0.0.0 INTRA-AREA 8
10.20.1.5 NnP
10.20.1.5/32 0.0.0.1 INTER-AREA 8
10.20.1.2 NnP
10.20.1.6/32 0.0.0.0 INTRA-AREA 9
10.20.1.6 NnP
10.20.1.6/32 0.0.0.1 INTER-AREA 9
10.20.1.2 NnP
------------------------------------------------------------------------
No. of Prefix/SIDs: 30
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
========================================================================
*A:Dut-F#
*A:Dut-C# show router ospf prefix-sids sid 66
========================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
========================================================================
Prefix Area RtType SID
Adv-Rtr Active Flags
------------------------------------------------------------------------
10.20.1.6/32 0.0.0.0 INTER-AREA 66
10.20.1.4 N NnP
10.20.1.6/32 0.0.0.0 INTER-AREA 66
10.20.1.5 Y NnP
10.20.1.6/32 0.0.0.1 INTER-AREA 66
10.20.1.2 N NnP
------------------------------------------------------------------------
No. of Prefix/SIDs: 3
Flags: N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
========================================================================
*A:Dut-C#
*A:Dut-C>config>router>ospf3# show router ospf3 0 prefix-sids
=========================================================================
Rtr Base OSPFv3 Instance 0 Prefix-Sids
=========================================================================
Prefix Area RtType SID
Adv-Rtr SRMS Flags
-------------------------------------------------------------------------
3ffe::100:b01/128 0.0.0.1 INTRA-AREA 4
10.20.1.1 N NnPA
3ffe::100:1602/128 0.0.0.1 INTRA-AREA 5
10.20.1.2 N NnPA
3ffe::100:2103/128 0.0.0.1 INTRA-AREA 0
10.20.1.3 N NnPA
3ffe::100:2c04/128 0.0.0.1 INTER-AREA 1
10.20.1.2 N NnP
3ffe::100:2c04/128 0.0.0.1 INTER-AREA 1
10.20.1.6 N NnP
3ffe::100:3705/128 0.0.0.1 INTER-AREA 2
10.20.1.2 N NnP
3ffe::100:3705/128 0.0.0.1 INTER-AREA 2
10.20.1.6 N NnP
3ffe::100:4206/128 0.0.0.1 INTRA-AREA 3
10.20.1.6 N NnPA
3ffe::a14:101/128 0.0.0.1 INTRA-AREA 10
10.20.1.1 N NnPA
3ffe::a14:102/128 0.0.0.1 INTER-AREA 11
10.20.1.2 N NnPA
3ffe::a14:102/128 0.0.0.1 INTER-AREA 11
10.20.1.6 N NnP
3ffe::a14:103/128 0.0.0.1 INTRA-AREA 6
10.20.1.3 N NnPA
3ffe::a14:104/128 0.0.0.1 INTER-AREA 7
10.20.1.2 N NnP
3ffe::a14:104/128 0.0.0.1 INTER-AREA 7
10.20.1.6 N NnP
3ffe::a14:105/128 0.0.0.1 INTER-AREA 8
10.20.1.2 N NnP
3ffe::a14:105/128 0.0.0.1 INTER-AREA 8
10.20.1.6 N NnP
3ffe::a14:106/128 0.0.0.1 INTER-AREA 9
10.20.1.2 N NnP
3ffe::a14:106/128 0.0.0.1 INTER-AREA 9
10.20.1.6 N NnPA
-------------------------------------------------------------------------
No. of Prefix/SIDs: 18
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
=========================================================================
*A:Dut-C#
*A:Dut-C# show router ospf prefix-sids
===============================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
===============================================================================
Prefix Area RtType SID
Algo Adv-Rtr SRMS Flags
-------------------------------------------------------------------------------
10.20.1.2/32 0.0.0.0 INTRA-AREA 2
0 10.20.1.2 N NnP
10.20.1.2/32 0.0.0.0 INTRA-AREA 1282
128 10.20.1.2 N NnP
10.20.1.3/32 0.0.0.0 INTRA-AREA 3
0 10.20.1.3 N NnP
10.20.1.3/32 0.0.0.0 INTRA-AREA 1283
128 10.20.1.3 N NnP
10.20.1.5/32 0.0.0.0 INTRA-AREA 5
0 10.20.1.5 N NnP
10.20.1.5/32 0.0.0.0 INTRA-AREA 1285
128 10.20.1.5 N NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 6
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
===============================================================================
*A:Dut-C#
*A:Dut-C#
*A:Dut-C#
*A:Dut-C# show router ospf prefix-sids algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
===============================================================================
Prefix Area RtType SID
Algo Adv-Rtr SRMS Flags
-------------------------------------------------------------------------------
10.20.1.2/32 0.0.0.0 INTRA-AREA 1282
128 10.20.1.2 N NnP
10.20.1.3/32 0.0.0.0 INTRA-AREA 1283
128 10.20.1.3 N NnP
10.20.1.5/32 0.0.0.0 INTRA-AREA 1285
128 10.20.1.5 N NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 3
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
===============================================================================
*A:Dut-C#
A:Dut-A>config>router# show router ospf prefix-sids
===============================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
===============================================================================
Prefix Area RtType SID Shared
Adv-Rtr SRMS Flags
-------------------------------------------------------------------------------
1.0.0.1/32 0.0.0.0 INTRA-AREA 4001 Yes
10.20.0.1 N NnP
10.20.0.1/32 0.0.0.0 INTRA-AREA 101 No
10.20.0.1 N NnP
10.20.0.2/32 0.0.0.0 INTRA-AREA 402 N.A.
10.20.0.2 N NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 3
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
Shared : Yes = local shared Node-SID
No = not a local shared Node-SID
N.A. = not applicable for Remote prefix-sid
===============================================================================
|
Label |
Description |
|---|---|
|
Prefix |
Displays the IP prefix for the SID |
|
Area |
Displays the OSPF area |
|
RtType |
Displays the route type (INTRA-AREA or INTER-AREA) |
|
SID |
Displays the SID value |
|
Adv-Rtr |
Displays the IP address of the advertised router |
|
SRMS |
Displays whether the prefix SID is advertised by the SR mapping server (Y or N) or selected to be programmed (S) |
|
Flags |
Displays the SID flags |
|
No. of Prefix/SIDs |
Displays the number of Prefix/SIDs |
prefix-sids
Syntax
prefix-sids [ip-prefix[/prefix-length]] [ sid sid] [adv-router router-id]
Context
[Tree] (show>router>ospf3 prefix-sids)
Full Context
show router ospf3 prefix-sids
Description
This command displays OSPF prefix SIDs.
Parameters
- ip-prefix[/prefix-length]
-
Displays information about the specified IP prefix and length, up to 64 characters.
- sid
-
Displays information for the specific segment identifier.
- router-id
-
Displays information for the specific advertising router identified by its router ID.
Platforms
All
Output
The following outputs are examples of OSPFv3 prefix SIDs information, and OSPFv3 Prefix SIDs Output Fields describes the output fields.
Output Example*A:Dut-F# show router ospf prefix-sids
========================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
========================================================================
Prefix Area RtType SID
Adv-Rtr Flags
------------------------------------------------------------------------
1.0.11.1/32 0.0.0.0 INTER-AREA 4
10.20.1.2 NnP
1.0.11.1/32 0.0.0.1 INTRA-AREA 4
10.20.1.1 NnP
1.0.11.1/32 0.0.0.1 INTRA-AREA 999
10.20.1.3 NnPB
1.0.22.2/32 0.0.0.0 INTER-AREA 5
10.20.1.2 NnPA
1.0.22.2/32 0.0.0.1 INTRA-AREA 5
10.20.1.2 NnP
1.0.22.2/32 0.0.0.1 INTRA-AREA 996
10.20.1.6 NnPB
1.0.33.3/32 0.0.0.0 INTER-AREA 0
10.20.1.2 NnP
1.0.33.3/32 0.0.0.1 INTRA-AREA 0
10.20.1.3 NnP
1.0.33.3/32 0.0.0.1 INTRA-AREA 998
10.20.1.1 NnPB
1.0.44.4/32 0.0.0.0 INTRA-AREA 1
10.20.1.4 NnP
1.0.44.4/32 0.0.0.0 INTRA-AREA 994
10.20.1.5 NnPB
1.0.44.4/32 0.0.0.1 INTER-AREA 1
10.20.1.2 NnP
1.0.55.5/32 0.0.0.0 INTRA-AREA 2
10.20.1.5 NnP
1.0.55.5/32 0.0.0.0 INTRA-AREA 995
10.20.1.4 NnPB
1.0.55.5/32 0.0.0.1 INTER-AREA 2
10.20.1.2 NnP
1.0.66.6/32 0.0.0.0 INTER-AREA 3
10.20.1.2 NnP
1.0.66.6/32 0.0.0.1 INTRA-AREA 3
10.20.1.6 NnP
1.0.66.6/32 0.0.0.1 INTRA-AREA 997
10.20.1.2 NnPB
10.20.1.1/32 0.0.0.0 INTER-AREA 10
10.20.1.2 NnP
10.20.1.1/32 0.0.0.1 INTRA-AREA 10
10.20.1.1 NnP
10.20.1.2/32 0.0.0.0 INTRA-AREA 11
10.20.1.2 NnP
10.20.1.2/32 0.0.0.1 INTER-AREA 11
10.20.1.2 NnPA
10.20.1.3/32 0.0.0.0 INTER-AREA 6
10.20.1.2 NnP
10.20.1.3/32 0.0.0.1 INTRA-AREA 6
10.20.1.3 NnP
10.20.1.4/32 0.0.0.0 INTRA-AREA 7
10.20.1.4 NnP
10.20.1.4/32 0.0.0.1 INTER-AREA 7
10.20.1.2 NnP
10.20.1.5/32 0.0.0.0 INTRA-AREA 8
10.20.1.5 NnP
10.20.1.5/32 0.0.0.1 INTER-AREA 8
10.20.1.2 NnP
10.20.1.6/32 0.0.0.0 INTRA-AREA 9
10.20.1.6 NnP
10.20.1.6/32 0.0.0.1 INTER-AREA 9
10.20.1.2 NnP
------------------------------------------------------------------------
No. of Prefix/SIDs: 30
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
========================================================================
*A:Dut-F#
*A:Dut-C# show router ospf prefix-sids sid 66
========================================================================
Rtr Base OSPFv2 Instance 0 Prefix-Sids
========================================================================
Prefix Area RtType SID
Adv-Rtr Active Flags
------------------------------------------------------------------------
10.20.1.6/32 0.0.0.0 INTER-AREA 66
10.20.1.4 N NnP
10.20.1.6/32 0.0.0.0 INTER-AREA 66
10.20.1.5 Y NnP
10.20.1.6/32 0.0.0.1 INTER-AREA 66
10.20.1.2 N NnP
------------------------------------------------------------------------
No. of Prefix/SIDs: 3
Flags: N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
========================================================================
*A:Dut-C#
*A:Dut-C>config>router>ospf3# show router ospf3 0 prefix-sids
=========================================================================
Rtr Base OSPFv3 Instance 0 Prefix-Sids
=========================================================================
Prefix Area RtType SID
Adv-Rtr SRMS Flags
-------------------------------------------------------------------------
3ffe::100:b01/128 0.0.0.1 INTRA-AREA 4
10.20.1.1 N NnPA
3ffe::100:1602/128 0.0.0.1 INTRA-AREA 5
10.20.1.2 N NnPA
3ffe::100:2103/128 0.0.0.1 INTRA-AREA 0
10.20.1.3 N NnPA
3ffe::100:2c04/128 0.0.0.1 INTER-AREA 1
10.20.1.2 N NnP
3ffe::100:2c04/128 0.0.0.1 INTER-AREA 1
10.20.1.6 N NnP
3ffe::100:3705/128 0.0.0.1 INTER-AREA 2
10.20.1.2 N NnP
3ffe::100:3705/128 0.0.0.1 INTER-AREA 2
10.20.1.6 N NnP
3ffe::100:4206/128 0.0.0.1 INTRA-AREA 3
10.20.1.6 N NnPA
3ffe::a14:101/128 0.0.0.1 INTRA-AREA 10
10.20.1.1 N NnPA
3ffe::a14:102/128 0.0.0.1 INTER-AREA 11
10.20.1.2 N NnPA
3ffe::a14:102/128 0.0.0.1 INTER-AREA 11
10.20.1.6 N NnP
3ffe::a14:103/128 0.0.0.1 INTRA-AREA 6
10.20.1.3 N NnPA
3ffe::a14:104/128 0.0.0.1 INTER-AREA 7
10.20.1.2 N NnP
3ffe::a14:104/128 0.0.0.1 INTER-AREA 7
10.20.1.6 N NnP
3ffe::a14:105/128 0.0.0.1 INTER-AREA 8
10.20.1.2 N NnP
3ffe::a14:105/128 0.0.0.1 INTER-AREA 8
10.20.1.6 N NnP
3ffe::a14:106/128 0.0.0.1 INTER-AREA 9
10.20.1.2 N NnP
3ffe::a14:106/128 0.0.0.1 INTER-AREA 9
10.20.1.6 N NnPA
-------------------------------------------------------------------------
No. of Prefix/SIDs: 18
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
=========================================================================
A:Dut-A>config>router# show router ospf3 prefix-sids
===============================================================================
Rtr Base OSPFv3 Instance 0 Prefix-Sids
===============================================================================
Prefix Area RtType SID Shared
Adv-Rtr SRMS Flags
-------------------------------------------------------------------------------
3ffe::100:1/128 0.0.0.0 INTRA-AREA 6001 Yes
10.20.0.1 N NnPA
3ffe::a14:1/128 0.0.0.0 INTRA-AREA 201 No
10.20.0.1 N NnPA
3ffe::a14:2/128 0.0.0.0 INTRA-AREA 402 N.A.
10.20.0.2 N NnPA
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 3
SRMS : Y/N = prefix SID advertised by SR Mapping Server (Y) or not (N)
S = SRMS prefix SID is selected to be programmed
SID Flags : N = Node-SID
nP = no penultimate hop POP
M = Mapping server
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
I = Inter Area flag
A = Attached flag
B = Backup flag
Shared : Yes = local shared Node-SID
No = not a local shared Node-SID
N.A. = not applicable for Remote prefix-sid
===============================================================================
|
Label |
Description |
|---|---|
|
Prefix |
Displays the IP prefix for the SID |
|
Area |
Displays the OSPF area |
|
RtType |
Displays the route type (INTRA-AREA or INTER-AREA) |
|
SID |
Displays the SID value |
|
Adv-Rtr |
Displays the IP address of the advertised router |
|
SRMS |
Displays whether the prefix SID is advertised by the SR mapping server (Y or N) or selected to be programmed (S) |
|
Flags |
Displays the SID flags |
|
No. of Prefix/SIDs |
Displays the number of Prefix/SIDs |
prefix-sids
Syntax
prefix-sids [interface ip-int-name] [ipv4 | ipv6]
Context
[Tree] (show>router>seg-rt>sr-mpls prefix-sids)
Full Context
show router segment-routing sr-mpls prefix-sids
Description
This command displays information about the prefix SIDs and their state on the router.
Parameters
- ip-int-name
-
Displays information about the specified interface, up to 32 characters.
- ipv4
-
Displays the prefix SIDs that are IPv4 capable.
- ipv6
-
Displays the prefix SIDs that are IPv6 capable.
Platforms
All
Output
The following output is an example of prefix SIDs information, and Prefix SIDs Output Fields describes the output fields.
Output Example*A:Dut-A# show router segment-routing sr-mpls prefix-sids
===============================================================================
Rtr Base SR-MPLS Prefix-SIDs
===============================================================================
Interface Name AF SID Label State
-------------------------------------------------------------------------------
System IPv4 123 100123 enabled
System IPv6 234 100234 ifFailed
loopback.0 IPv4 345 100345 ifDown
loopback.0 IPv6 456 100456 ifDown
loopback.4 IPv4 567 100567 failed
loopback.4 IPv6 - - adminDown
loopback.6 IPv4 - - adminDown
loopback.6 IPv6 678 100678 notPref
-------------------------------------------------------------------------------
No. of Prefix-SIDs: 4
===============================================================================
|
Label |
Description |
|---|---|
|
Interface Name |
The name of the loopback or system interface |
|
AF |
The address family associated with the prefix SID |
|
SID |
The SID index |
|
Label |
The SID label |
|
State |
The operational state of the prefix SID
|
prefix-stats
prefix-stats
Syntax
prefix-stats ipv6-address/prefix-length
prefix-stats pool pool-name
Context
[Tree] (show>router>dhcp6>local-dhcp-server prefix-stats)
Full Context
show router dhcp6 local-dhcp-server prefix-stats
Description
This command displays prefix statistics.
Parameters
- ipv6-address
-
Specifies the base IP address of the subnet. This address must be unique within the subnet and specified in dotted decimal notation. Allowed values are IP addresses in the range 1.0.0.0 – 223.255.255.255 (with support of /31 subnets).
- pool-name
-
Specifies the name of DHCPv6 local server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
prefix-threshold-stats
prefix-threshold-stats
Syntax
prefix-threshold-stats pool pool-name detail [ format {exact | scientific}]
prefix-threshold-stats pool pool-name
prefix-threshold-stats ipv6-address/prefix-length detail [format {exact | scientific}]
prefix-threshold-stats ipv6-address/prefix-length
Context
[Tree] (show>router>dhcp6>server prefix-threshold-stats)
Full Context
show router dhcp6 local-dhcp-server prefix-threshold-stats
Description
This commands displays prefix level threshold stats of local DHCPv6 server prefix. A minimum-free threshold needs to be configured before system collects threshold stats for the prefix.
The stats for each threshold are calculated based on the configured minimum-free prefix length.
For example, a /59 prefix is provision in the local DHCPv6 server, and the server allocated two PD leases, one /62 and one /63. And there is a /63 minimum threshold configured. The threshold stats are calculated based on /63 as the base unit (block). Then the value of the current used block would be 3 because there is one /62 lease and one /63 lease, that equals to a total three /63.
Parameters
- pool pool-name
-
Specifies the name of the pool in local DHCPv6 server, up to 32 characters.
- detail
-
Displays detailed output statistics.
- format
-
Specifies that the number format in the display is either exact or scientific.
- ipv6-address/prefix-length
-
Specifies the IPv6 prefix with prefix length.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of prefix threshold information.
Output Exampleshow router 500 dhcp6 local-dhcp-server "d6" leases
===============================================================================
Leases for DHCPv6 server d6
===============================================================================
IP Address/Prefix Lease State Remaining Fail
Link-local Address LifeTime Ctrl
-------------------------------------------------------------------------------
8888:0:0:ffe0:db8:/62
fe80::3:ffff:fe00:db8:111 stable 18h19m2s local
8888:0:0:ffe4::/63
fe80::3:ffff:fe00:db8:211 stable 19h49m37s local
-------------------------------------------------------------------------------
2 leases found
===============================================================================
show router 500 dhcp6 local-dhcp-server "d6" prefix-threshold-stats pool "1"
===============================================================================
Server "d6"
===============================================================================
Operational state : inService
-------------------------------------------------------------------------------
Pool : 1
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
-------------------------------------------------------------------------------
Prefix : 8888:0:0:ffe0:db8:/59
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
Draining : N
-----------------------------------------------------------------------------
Threshold Used Peak Too low Depleted Peak timestamp
-----------------------------------------------------------------------------
/62 25% 25% Y N 01/20/2015 23:51:36
/63 19% 19% N N 01/21/2015 05:00:53
===============================================================================
The command shown above displays an overview of prefix level thresholds in the specified pool:
-
The Peak field indicates the peak value of used.
-
The Too low field indicate if the configured minimum-free threshold is exceeded.
-
The Depleted field indicate if there is no available prefix with the length in the provisioned prefix.
-
The Peak timestamp field indicates the time of peak used value.
show router 500 dhcp6 local-dhcp-server "d6" prefix-threshold-stats pool "1" detail
===============================================================================
Server "d6"
===============================================================================
Operational state : inService
-------------------------------------------------------------------------------
Pool : 1
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
-------------------------------------------------------------------------------
Prefix : 8888:0:0:ffe0::/59
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
Draining : N
-----------------------------------------------------------------------------
Threshold : /62
-----------------------------------------------------------------------------
Current Provisioned Blks : 8.000000x10^0
Current Used Blks : 2.000000x10^0
Current Free Blks : 6.000000x10^0
Current Used Percent : 25%
Current Used Peak Blks : 2.000000x10^0
Current Used Peak Percent : 25%
Current Used Peak Time : 01/21/2015 21:59:02
Current Free Percent : 75%
Current Free Too Low : N
Current Free Depleted : N
Local Provisioned Blks : 8.000000x10^0
Local Used Blks : 2.000000x10^0
Local Free Blks : 6.000000x10^0
Local Used Peak Blks : 2.000000x10^0
Local Used Peak Percent : 25%
Local Used Peak Time : 01/21/2015 21:59:02
Remote Provisioned Blks : 0.000000x10^0
Remote Used Blks : 0.000000x10^0
Remote Free Blks : 0.000000x10^0
Remote Used Peak Blks : 0.000000x10^0
Remote Used Peak Percent : 0%
Remote Used Peak Time : 01/21/2015 21:59:02
Peak Reset Time : 01/21/2015 21:59:02
Valid Data : Y
-----------------------------------------------------------------------------
Threshold : /63
-----------------------------------------------------------------------------
Current Provisioned Blks : 1.600000x10^1
Current Used Blks : 3.000000x10^0
Current Free Blks : 1.300000x10^1
Current Used Percent : 19%
Current Used Peak Blks : 3.000000x10^0
Current Used Peak Percent : 19%
Current Used Peak Time : 01/21/2015 21:59:13
Current Free Percent : 81%
Current Free Too Low : N
Current Free Depleted : N
Local Provisioned Blks : 1.600000x10^1
Local Used Blks : 3.000000x10^0
Local Free Blks : 1.300000x10^1
Local Used Peak Blks : 3.000000x10^0
Local Used Peak Percent : 19%
Local Used Peak Time : 01/21/2015 21:59:13
Remote Provisioned Blks : 0.000000x10^0
Remote Used Blks : 0.000000x10^0
Remote Free Blks : 0.000000x10^0
Remote Used Peak Blks : 0.000000x10^0
Remote Used Peak Percent : 0%
Remote Used Peak Time : 01/21/2015 21:59:13
Peak Reset Time : 01/21/2015 21:59:13
Valid Data : Y
The command shown above displays detailed statistics of all prefix level thresholds in the specified pool:
-
Blks means the minimum free prefix length.
-
Valid Data output indicates whether the data is or is not valid. The data is invalid when a background stats update is scheduled or busy.
show router 500 dhcp6 local-dhcp-server "d6" prefix-threshold-
stats 8888:0:0: ffe0:db8:/59
===============================================================================
Server "d6"
===============================================================================
Operational state : inService
-------------------------------------------------------------------------------
Pool : 1
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
-------------------------------------------------------------------------------
Prefix : 8888:0:0:ffe0:db8:/59
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
Draining : N
-----------------------------------------------------------------------------
Threshold Used Peak Too low Depleted Peak timestamp
-----------------------------------------------------------------------------
/62 25% 25% N N 01/21/2015 21:59:02
/63 19% 19% N N 01/21/2015 21:59:13
The command shown above displays an overview of prefix level thresholds in the specified provision prefix.
show router 500 dhcp6 local-dhcp-server "d6" prefix-threshold-stats 8888:0:0:ffe0::/
59 detail
===============================================================================
Server "d6"
===============================================================================
Operational state : inService
-------------------------------------------------------------------------------
Pool : 1
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
-------------------------------------------------------------------------------
Prefix : 8888:0:0:ffe0:db8:/59
-------------------------------------------------------------------------------
Stable leases : 2
Advertised leases : 0
Draining : N
-----------------------------------------------------------------------------
Threshold : /62
-----------------------------------------------------------------------------
Current Provisioned Blks : 8.000000x10^0
Current Used Blks : 2.000000x10^0
Current Free Blks : 6.000000x10^0
Current Used Percent : 25%
Current Used Peak Blks : 2.000000x10^0
Current Used Peak Percent : 25%
Current Used Peak Time : 01/21/2015 21:59:02
Current Free Percent : 75%
Current Free Too Low : N
Current Free Depleted : N
Local Provisioned Blks : 8.000000x10^0
Local Used Blks : 2.000000x10^0
Local Free Blks : 6.000000x10^0
Local Used Peak Blks : 2.000000x10^0
Local Used Peak Percent : 25%
Local Used Peak Time : 01/21/2015 21:59:02
Remote Provisioned Blks : 0.000000x10^0
Remote Used Blks : 0.000000x10^0
Remote Free Blks : 0.000000x10^0
Remote Used Peak Blks : 0.000000x10^0
Remote Used Peak Percent : 0%
Remote Used Peak Time : 01/21/2015 21:59:02
Peak Reset Time : 01/21/2015 21:59:02
Valid Data : Y
-----------------------------------------------------------------------------
Threshold : /63
-----------------------------------------------------------------------------
Current Provisioned Blks : 1.600000x10^1
Current Used Blks : 3.000000x10^0
Current Free Blks : 1.300000x10^1
Current Used Percent : 19%
Current Used Peak Blks : 3.000000x10^0
Current Used Peak Percent : 19%
Current Used Peak Time : 01/21/2015 21:59:13
Current Free Percent : 81%
Current Free Too Low : N
Current Free Depleted : N
Local Provisioned Blks : 1.600000x10^1
Local Used Blks : 3.000000x10^0
Local Free Blks : 1.300000x10^1
Local Used Peak Blks : 3.000000x10^0
Local Used Peak Percent : 19%
Local Used Peak Time : 01/21/2015 21:59:13
Remote Provisioned Blks : 0.000000x10^0
Remote Used Blks : 0.000000x10^0
Remote Free Blks : 0.000000x10^0
Remote Used Peak Blks : 0.000000x10^0
Remote Used Peak Percent : 0%
Remote Used Peak Time : 01/21/2015 21:59:13
Peak Reset Time : 01/21/2015 21:59:13
Valid Data : Y
The command displayed above displays detailed statistics of prefix level thresholds in the specified provision prefix.
Prefix Threshold Statistics Field Descriptions describes prefix threshold statistics output fields.
|
Field |
Description |
|---|---|
|
Operational state |
The operational state of the local DHCP server instance unknown — The operational state is unknown inService — The operational state is in service outOfService — The operational state is out of service transition — The operational state is in transition waitPersistence — The DHCP server instance is waiting for a persistence action to complete. |
|
Pool |
The number of pools in the specified prefix |
|
Stable leases |
The number of stable leases associated with the prefix |
|
Advertised leases |
The advertised leases associated with the prefix |
|
Prefix |
The specified prefix |
|
Draining |
The draining state Y — enabled N — disabled |
|
Threshold |
The prefix level threshold |
|
Current Provisioned Blks |
The number of provisioned blocks for this prefix |
|
Current Used Blks |
The number of used blocks for this prefix |
|
Current Free Blks |
The number of free blocks for this prefix |
|
Current Used Percent |
The percentage of used prefixes with the minimum free threshold length for this prefix |
|
Current Used Peak Blks |
A 64-bit word of the peak value of the number of used blocks for this prefix |
|
Current Used Peak Percentage |
The peak value of the number of used prefixes with the minimum free threshold length in the pool as a percentage of the provisioned prefixes. |
|
Current Used Peak Time |
The time at which the peak value of the number of used prefixes in the pool was reached |
|
Current Free Percent |
The percentage of free prefixes with the minimum free threshold length in the pool compared to the number of provisioned prefixes. |
|
Current Free Too Low |
The number of free prefixes with the minimum free threshold length available in the pool that is below the configured number of prefixes with the minimum free threshold length |
|
Current Free Depleted |
The number of prefixes with the minimum free threshold length available |
|
Local Provisioned Blks |
A 64-bit word of the number of provisioned prefixes with the minimum free threshold length local |
|
Local Used Blks |
The higher 64-bits word of the number of used prefixes with the minimum free threshold length |
|
Local Free Blks |
A 64-bit word of the number of free prefixes with the minimum free threshold length |
|
Local Used Peak Blks |
A 64-bit word of the peak value of the number of used prefixes with the minimum free threshold length |
|
Local Used Peak Percent |
The peak value of the number of used prefixes with the minimum free threshold length local in the pool as a percentage of the provisioned prefixes |
|
Local Used Peak Time |
The time at which the peak value of the number of used prefixes local in the pool was reached |
|
Remote Provisioned Blks |
A 64-bit word of the number of provisioned prefixes with the minimum free threshold length |
|
Remote Used Blks |
A 64-bit word of the number of used prefixes with the minimum free threshold length remote in the pool |
|
Remote Free Blks |
A 64-bit word of the number of free prefixes with the minimum free threshold length remote in the pool |
|
Remote Used Peak Blks |
The higher 64-bit word of the number of used prefixes with the minimum free threshold length |
|
Remote Used Peak Percent |
The peak value of the number of used prefixes with the minimum free threshold length remote in the pool as a percentage of the provisioned prefixes |
|
Remote Used Peak Time |
The time at which the peak value of the number of used prefixes remote in the pool was reached. |
|
Peak Reset Time |
The time at which the peak values have been reset |
|
Valid Dada |
The actual status of the threshold statistics data of the pool. Y — the data is up to date and may be used. N — the data is being recalculated in the background and is not stable for further use |
prefix-threshold-stats
Syntax
prefix-threshold-stats ipv6-address/prefix-length
prefix-threshold-stats pool pool-name
Context
[Tree] (clear>router>dhcp6>server prefix-threshold-stats)
Full Context
clear router dhcp6 local-dhcp-server prefix-threshold-stats
Description
This commands resets the peak stats in the prefix level threshold stats in the specified provision prefix or pool.
Parameters
- pool-name
-
Clears information about the specified pool in local DHCPv6 server.
- ipv6-address/prefix-length
-
Clears information about the specified IPv6 prefix with prefix length.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
prefixes
prefixes
Syntax
prefixes prefix ip-prefix/ip-prefix-length [ summary | detail] [session ip-addr[ label-space]] [community community]
prefixes prefix [family] [summary | detail] [session ip-addr[label-space]] [community community]
prefixes [family] [summary | detail] [ egress-if port-id] [community community]
prefixes [family] [summary | detail] [ egress-lsp tunnel-id] [community community]
prefixes [egress-nh ip-address] [family] [ summary | detail] [community community]
prefixes prefix ip-prefix/ip-prefix-length [ summary | detail] [egress-if port-id] [community community]
prefixes prefix ip-prefix/ip-prefix-length [ summary | detail] [egress-lsp tunnel-id] [community community]
prefixes prefix ip-prefix/ip-prefix-length [ egress-nh ip-address] [summary | detail] [community community]
Context
[Tree] (show>router>ldp>bindings prefixes)
Full Context
show router ldp bindings prefixes
Description
This command displays LDP Prefix fec bindings.
Parameters
- prefix ip-prefix/ip-prefix-length
-
Specify information for the specified IP prefix and mask length.
- session ip-addr[label-space]
-
Specify information for the specified IP address and label space.
- detail
-
Displays detailed information.
- summary
-
Displays information in a summarized format.
- family
-
Displays either IPv4 or IPv6 active LDP information.
- egress-lsp tunnel-id
-
Specifies the tunnel identifier for this egress LSP.
- egress-nh ip-address
-
Displays LDP active bindings by matching egress-nh.
- egress-if port-id
-
Displays LDP active bindings by matching egress-if.
- community
-
The string defining the LDP community assigned to the session. Allowed values are any string up to 32 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
Output
Output Example*A:SRU4# show router ldp bindings prefixes
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.4)
(IPv6 LSR ID 3ffe::6e14:104)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, M - Community Mismatch, BA - ASBR Backup FEC
===============================================================================
LDP IPv4 Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl
Peer EgrIntf/LspId
EgrNextHop FEC-Flags
-------------------------------------------------------------------------------
0.0.0.0/0 -- 16910
10.100.1.1:0 --
--
1.1.1.0/24 3U 14828
10.100.1.1:0 --
--
1.1.1.0/24 3U 3e
10.20.1.1:0
*A:Dut-C>config>router>ldp# show router ldp bindings prefixes detail
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.4)
(IPv6 LSR ID 3ffe::6e14:104)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, M - Community Mismatch, BA - ASBR Backup FEC
==============================================================================
LDP IPv4 Prefix Bindings
==============================================================================
-------------------------------------------------------------------------------
Prefix : 0.0.0.0/0
-------------------------------------------------------------------------------
Peer : 10.100.1.1:0
Community : RED
Ing Lbl : -- Egr Lbl : 16910
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
Egr If Name : n/a
-------------------------------------------------------------------------------
Prefix : 1.1.1.0/24
-------------------------------------------------------------------------------
Peer : 10.100.1.1:0
Community : RED
Ing Lbl : 3U Egr Lbl : 14828
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
Egr If Name : n/a
-------------------------------------------------------------------------------
Prefix : 1.1.1.0/24
-------------------------------------------------------------------------------
prefixes
Syntax
prefixes [family] [summary | detail] [ egress-if port-id] [community community]
prefixes [family] [summary | detail] [ egress-lsp tunnel-id] [community community]
prefixes [egress-nh ip-address] [family] [ summary | detail] [community community]
prefixes prefix ip-prefix/ip-prefix-length [summary | detail] [egress-if port-id] [community community]
prefixes prefix ip-prefix/ip-prefix-length [summary | detail] [egress-lsp tunnel-id] [community community]
prefixes prefix ip-prefix/ip-prefix-length [egress-nh ip-address] [summary | detail] [community community]
Context
[Tree] (show>router>ldp>bindings>active prefixes)
Full Context
show router ldp bindings active prefixes
Description
This command displays LDP active prefix bindings.
Parameters
- ip-prefix/ip-prefix-length
-
Specifies information for the IP prefix and mask length.
- ip-address
-
Specifies the IPv4 or IPv6 address.
- family
-
Specifies the address family.
- port-id
-
Specifies the port ID.
- tunnel-id
-
Specifies the tunnel ID.
- community
-
The string defining the LDP community assigned to the session. Allowed values are any string up to 32 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
profile
profile
Syntax
profile [user-profile-name]
Context
[Tree] (show system security profile)
Full Context
show system security profile
Description
This command displays user profile information.
If the profile-name is not specified, then information for all profiles are displayed.
Parameters
- user-profile-name
-
Displays information for the specified user profile.
Platforms
All
Output
The following output is an example of user profile output information.
Show User Profile Output Fields describes user profile output fields.
Output ExampleA:ALA-7# show system security profile administrative
===============================================================================
User Profile
===============================================================================
User Profile : administrative
Def. Action : permit-all
-------------------------------------------------------------------------------
Entry : 10
Description :
Match Command: configure system security
Action : permit
-------------------------------------------------------------------------------
Entry : 20
Description :
Match Command: show system security
Action : permit
-------------------------------------------------------------------------------
No. of profiles:
===============================================================================
A:ALA-7#
|
Label |
Description |
|---|---|
|
User Profile |
Displays the profile name used to deny or permit user console access to a hierarchical branch or to specific commands. |
|
Def. action |
Permit all — Permits access to all commands. Deny — Denies access to all commands. None — No action is taken. |
|
Entry |
The entry ID in a policy or filter table. |
|
Description |
Displays the text string describing the entry. |
|
Match Command |
Displays the command or subtree commands in subordinate command levels. |
|
Action |
Permit all — Commands matching the entry command match criteria are permitted. Deny — Commands not matching the entry command match criteria are not permitted. |
|
No. of profiles |
The total number of profiles listed. |
profile
Syntax
profile [profile-name]
Context
[Tree] (show system security profile)
Full Context
show system security profile
Description
This command displays user profiles for CLI command tree permissions.
Parameters
- profile-name
-
Specify the profile name to display information about a single user profile. If no profile name is displayed, the entire list of profile names are listed.
Platforms
All
Output
The following output is an example of profile information.
Show Profile Output Fields describes the profile output fields.
Output ExampleA:ALA-48>config>system>snmp# show system security profile
===============================================================================
User Profile
===============================================================================
User Profile : test
Def. Action : none
-------------------------------------------------------------------------------
Entry : 1
Description :
Match Command:
Action : unknown
===============================================================================
User Profile : default
Def. Action : none
-------------------------------------------------------------------------------
Entry : 10
Description :
Match Command: exec
Action : permit
-------------------------------------------------------------------------------
Entry : 20
Description :
Match Command: exit
Action : permit
-------------------------------------------------------------------------------
Entry : 30
Description :
Match Command: help
Action : permit
-------------------------------------------------------------------------------
...
-------------------------------------------------------------------------------
Entry : 80
Description :
Match Command: enable-admin
Action : permit
===============================================================================
User Profile : administrative
Def. Action : permit-all
-------------------------------------------------------------------------------
Entry : 10
Description :
Match Command: configure system security
Action : permit
-------------------------------------------------------------------------------
Entry : 20
Description :
Match Command: show system security
Action : permit
===============================================================================
-------------------------------------------------------------------------------
No. of profiles: 3
===============================================================================
A:ALA-48>config>system>snmp#
|
Label |
Description |
|---|---|
|
User Profile |
default — Displays the action to be given to the user profile if none of the entries match the command. administrative — Specifies the administrative state for this profile. |
|
Def. Action |
none — No action is given to the user profile when none of the entries match the command. permit-all — The action to be taken when an entry matches the command. |
|
Entry |
10 - 80 — Displays an entry which represents the configuration for a system user. |
|
Description |
A text string describing the entry. |
|
Match Command |
administrative — Enables the user to execute all commands. configure system security — Enables the user to execute the config system security command. enable-admin — Enables the user to enter a special administrative mode by entering the enable-admin command. exec — Enables the user to execute (exec) the contents of a text file as if they were CLI commands entered at the console. exit — Enables the user to execute the exit command. help — Enables the user to execute the help command. logout — Enables the user to execute the logout command. password — Enables the user to execute the password command. show config — Enables the user to execute the show config command. show — Enables the user to execute the show command. show system security — Enables the user to execute the show system security command. |
|
Action |
permit — Enables the user access to all commands. deny-all — Denies the user access to all commands. |
protection-template
protection-template
Syntax
protection-template
Context
[Tree] (show>router>mpls>mpls-tp protection-template)
Full Context
show router mpls mpls-tp protection-template
Description
This command displays MPLS-TP protection template information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of MPLS protection template fields.
Output Example*A:mlstp-dutA# show router mpls mpls-tp protection-template
===============================================================================
MPLS-TP Protection Templates
===============================================================================
Template Name : privatebed-protection-template Router ID : 1
Protection Mode: one2one Direction : bidirectional
Revertive : revertive Wait-to-Restore: 300sec
Rapid-PSC-Timer: 10ms Slow-PSC-Timer : 5sec
===============================================================================
protocol
protocol
Syntax
protocol
Context
[Tree] (clear>router>bgp protocol)
Full Context
clear router bgp protocol
Description
This command resets the entire BGP protocol. If the AS number was previously changed, the BGP AS number does not inherit the new value.
Platforms
All
protocol
Syntax
protocol [protocol-name] count [detail]
protocol count [detail]
protocol count top granularity [max-count max-count]
Context
[Tree] (show>app-assure>group protocol)
[Tree] (show>app-assure>group>aa-sub protocol)
Full Context
show application-assurance group protocol
show application-assurance group aa-sub protocol
Description
This command displays per-protocol statistics. The system-wide statistics displayed account for all flows completed and the last internal snapshot of the active flows.
Subscriber statistics are available for special study subscribers and account for all completed and active flows at the moment of this statistics request.
Parameters
- protocol-name
-
Displays information about the specified protocol name.
- count
-
Displays protocol counters.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the protocol command.
Output ExampleA:ALU>show>app-assure>group# protocol count
===============================================================================
Protocol Statistics
===============================================================================
Protocol Disc Octets Packets Flows
-------------------------------------------------------------------------------
aim_oscar 0% 0 0 0
aim_oscar_file_xfer 0% 0 0 0
aim_oscar_video_voice 0% 0 0 0
aim_toc 0% 0 0 0
bittorrent 0% 0 0 0
...
A:ALU>show>app-assure>group# protocol "http_audio" count detail
===============================================================================
Protocol "http_audio" Statistics
===============================================================================
Protocol:
Type Octets Packets Flows
-------------------------------------------------------------------------------
http_audio:
Admitted from subscriber: 14958 201 2
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 587590 396 2
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Total flow duration: 21 seconds
Terminated flows: 4
Short Duration flows: 4
Medium Duration flows: 0
Long Duration flows: 0
Active subscribers: 1
===============================================================================
A:ALU>show>app-assure>group#
protocol
Syntax
protocol [protocol-name]
protocol [protocol-name] detail
Context
[Tree] (show>app-assure protocol)
Full Context
show application-assurance protocol
Description
This command displays application-assurance policy protocols loaded from the isa-aa.tim file.
Parameters
- protocol-name
-
Displays all protocols from the isa-aa.tim file.
- detail
-
Displays detailed information about the specified protocol name.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the protocol command information.
Output ExampleA:ALU-ABC>show>app-assure# protocol
===============================================================================
Application Assurance Protocols
===============================================================================
Protocol : Description
-------------------------------------------------------------------------------
aim_oscar : America Online Oscar Instant Messaging.
aim_oscar_file_xfer : America Online Oscar File Transfer.
aim_oscar_video_voice : America Online Oscar Video and Voice
Traffic.
aim_toc : America Online Talk to Oscar Instant
Messaging.
bittorrent : BitTorrent peer to peer protocol.
...
A:ALU-ABC>show>app-assure#
A:ALU-ABC>show>app-assure# protocol tftp
===============================================================================
Application Assurance Protocols
===============================================================================
Protocol : Description
-------------------------------------------------------------------------------
tftp : IETF RFC 1350: Trivial File Transfer
Protocol.
===============================================================================
A:ALU-ABC>show>app-assure#
protocol-list
protocol-list
Syntax
protocol-list [protocol-list-name]
protocol-list protocol-list-name references
Context
[Tree] (show>filter>match-list protocol-list)
Full Context
show filter match-list protocol-list
Description
This command displays the protocol-list information.
Parameters
- protocol-list-name
-
A string of up to 32 characters of printable ASCII characters. If special characters are used, the string must be enclosed within double quotes.
- references
-
Displays the filter policies and policy entries referring to this match.
Platforms
All
protocol-protection
protocol-protection
Syntax
protocol-protection
Context
[Tree] (show>system>security>cpu-protection protocol-protection)
Full Context
show system security cpu-protection protocol-protection
Description
This command display all interfaces with non-zero drop counters.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-7s, 7750 SR-14s, 7950 XRS
protocol-protection
Syntax
protocol-protection
Context
[Tree] (clear>cpu-protection protocol-protection)
Full Context
clear cpu-protection protocol-protection
Description
This command clears the interface counts of packets dropped by protocol protection.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-7s, 7750 SR-14s, 7950 XRS
provider-tunnel
provider-tunnel
Syntax
provider-tunnel
provider-tunnel spmsi-tunnels [detail]
Context
[Tree] (show>service>id provider-tunnel)
Full Context
show service id provider-tunnel
Description
This command displays the service provider tunnel information.
Platforms
All
Output
The following command displays the service provider tunnel information and Show provider tunnel output fields describes the output fields.
show service id provider-tunnel===============================================================================
Service Provider Tunnel Information
===============================================================================
Type : inclusive Root and Leaf : enabled
Admin State : disabled Data Delay Intvl : 15 secs
PMSI Type : ldp LSP Template :
Remain Delay Intvl : 0 secs LSP Name used : 8193
PMSI Owner : bgpEvpnMpls
Oper State : up Root Bind Id : 32767
-------------------------------------------------------------------------------
Type : selective wildcard-spmsi : enabled
Admin State : enabled Data Delay Intvl : 15 secs
PMSI Type : ldp Maximum-p2mp-spmsi : 10
PMSI Owner : bgpEvpnMpls
Oper State : up
Group-range : 239.1.0.0/16 s-pmsi-threshold : 10 kbps
Pe-threshold-add : 2 Pe-threshold-delete: 10
Group-range : 239.2.0.0/24 s-pmsi-threshold : 0 kbps
Pe-threshold-add : 3 Pe-threshold-delete: 5
===============================================================================
Tthe following command displays the service provider tunnel information and Show provider tunnel output fields describes the output fields.
show service id provider-tunnel===============================================================================
Service Provider Tunnel Information
===============================================================================
Type : inclusive Root and Leaf : disabled
Admin State : disabled Data Delay Intvl : 15 secs
PMSI Type : none LSP Template :
Remain Delay Intvl : 0 secs LSP Name used :
PMSI Owner : none
-------------------------------------------------------------------------------
Type : selective Wildcard SPMSI : enabled
Admin State : enabled Data Delay Intvl : 5 secs
PMSI Type : mLdp Max P2MP SPMSI : 10
PMSI Owner : bgpEvpnMpls
Group range : 224.0.0.0/4
S-PMSI Threshold : 0 kbps
PE Threshold add : 65535 PE Threshold del : 65535
Group range : 239.0.0.0/8
S-PMSI Threshold : 1 kbps
PE Threshold add : 65535 PE Threshold del : 65535
===============================================================================The following command displays the service provider tunnel SPMSI information and Show provider tunnel output fields describes the output fields.
show service id provider-tunnel spmsi-tunnels===============================================================================
LDP Spmsi Tunnels
===============================================================================
LSP ID : 8199
Root Address : 192.0.2.4
S-PMSI If Index : 73743
Num. Leaf PEs : 2
Uptime : 0d 00:00:00
Group Address : 239.0.0.4
Source Address : 10.0.0.4
Origin IP Address : 192.0.2.4
State : TX Join Pending
Remain Delay Intvl : 3
-------------------------------------------------------------------------------
LSP ID : 8197
Root Address : 192.0.2.4
S-PMSI If Index : 73739
Uptime : 0d 00:28:37
Group Address : * (wildcard)
Source Address : *
Origin IP Address : 192.0.2.4
State : TX Joined
Remain Delay Intvl : 0
-------------------------------------------------------------------------------
===============================================================================The following command displays the service provider tunnel SPMSI detailed information and Show provider tunnel output fields describes the output fields.
show service id provider-tunnel spmsi-tunnels detail===============================================================================
LDP Spmsi Tunnels
===============================================================================
LSP ID : 8199
Root Address : 192.0.2.4
S-PMSI If Index : 73743
Num. Leaf PEs : 2
Uptime : 0d 00:00:03
Group Address : 239.0.0.4
Source Address : 10.0.0.4
Origin IP Address : 192.0.2.4
State : TX Joined
Remain Delay Intvl : 0
Group Receiver PE : 192.0.2.2, 192.0.2.3
-------------------------------------------------------------------------------
LSP ID : 8197
Root Address : 192.0.2.4
S-PMSI If Index : 73739
Uptime : 0d 00:28:44
Group Address : * (wildcard)
Source Address : *
Origin IP Address : 192.0.2.4
State : TX Joined
Remain Delay Intvl : 0
-------------------------------------------------------------------------------
===============================================================================|
Label |
Description |
|---|---|
|
Service Provider Tunnel Information |
|
|
Type |
The provider tunnel type (inclusive or selective) |
|
Root and Leaf |
The root and leaf status |
|
Admin State |
The administrative state |
|
Data Delay Intvl |
The data delay interval in seconds |
|
PMSI Type |
The PMSI type |
|
LSP Template |
The LSP template name |
|
Remain Delay Intvl |
The remaining delay interval in seconds |
|
LSP Name used |
The LSP name |
|
PMSI Owner |
The PMSI owner |
|
Oper State |
The operational state |
|
Root Bind Id |
The root binding ID |
|
wildcard-spmsi/Wildcard SPMSI |
The wildcard SPMSI status |
|
Maximum-p2mp-spmsi/Max P2MP SPMSI |
The maximum P2MP SPMSI value |
|
Group-range/Group range |
The group range |
|
s-pmsi-threshold/ S-PMSI Threshold |
The SPMSI threshold so that the root node attempts to setup an S-PMSI tree, in Kbps |
|
Pe-threshold-add/ PE Threshold add |
The PE threshold add value |
|
Pe-threshold-delete/PE Threshold del |
The PE threshold delete value |
|
LDP Spmsi tunnels |
|
|
LSP ID |
The LSP ID |
|
Root Addr/Root Address |
The root address |
|
Spmsi IfIndex/S-PMSI If Index |
The SPMSI If Index value |
|
Num. Leaf PEs |
The number of leaf PEs |
|
Number of SGs |
The number of SGs |
|
Uptime |
The cummulative up time |
|
Group Address |
The group address |
|
Source Address |
The source address |
|
Origin IP Address |
The origin IP address |
|
State |
The state value |
|
S-pmsi Threshold |
The SPMSI threshold value |
|
Remain Delay Intvl |
The remaining delay interval in seconds |
|
Group Receiver PE |
The group receiver PE IP address |
|
Leaf Address |
The Leaf IP addresses |
|
Pe-threshold-add |
The PE threshold add value |
|
Pe-threshold-delete |
The PE threshold delete value |
|
Current Receiver PE Count |
The current receive PE count value |
|
LDP Spmsi Tunnels |
The total number of SPMSI tunnels |
provider-tunnel-using
provider-tunnel-using
Syntax
provider-tunnel-using leaf-only [bgp-ad | bgp-vpls | bgp-evpn-mpls]
provider-tunnel-using root-and-leaf [bgp-ad | bgp-vpls | bgp-evpn-mpls]
Context
[Tree] (show>service provider-tunnel-using)
Full Context
show service provider-tunnel-using
Description
This command displays the list of provider tunnels existing in the router for all services. The output can be filtered based on the provider tunnel owner.
Parameters
- leaf-only
-
Displays the leaf-only provider tunnels for all services.
- root-and-leaf
-
Displays the root and leaf provider tunnels for all services.
- bgp-ad
-
Filters the provider tunnels owned by BGP AD services.
- bgp-vpls
-
Filters the provider tunnels owned by BGP VPLS services.
- bgp-evpn-mpls
-
Filters the provider tunnels owned by BGP EVPN-MPLS services.
Platforms
All
Output
The following output is an example of provider tunnel using information.
Output ExampleA:PE-76# show service provider-tunnel-using root-and-leaf
=====================================================
Provider-Tunnel Using (Root-and-Leaf)
=====================================================
SvcId SdpId Owner Admin Oper
State State
-----------------------------------------------------
300 32767:4294967294 bgpEvpnMpls Up Up
-----------------------------------------------------
Number of Root-and-Leaf : 1
=====================================================
A:PE-76# show service provider-tunnel-using root-and-leaf bgp-evpn-mpls
=====================================================
Provider-Tunnel Using (Root-and-Leaf)
=====================================================
SvcId SdpId Owner Admin Oper
State State
-----------------------------------------------------
300 32767:4294967294 bgpEvpnMpls Up Up
-----------------------------------------------------
Number of Root-and-Leaf : 1
=====================================================
provider-tunnels
provider-tunnels
Syntax
provider-tunnels [type {originating | terminating}
Context
[Tree] (tools>dump>service>id provider-tunnels)
Full Context
tools dump service id provider-tunnels
Description
This command dumps the inclusive or selective provider tunnels based on type.
Platforms
All
Output
Use the following command to display terminating provider tunnels.
tools dump service id provider-tunnels type terminating ========================================================================
VPLS 1001 Inclusive Provider Tunnels Terminating
========================================================================
ipmsi (RSVP) P2MP-ID Tunl-ID Ext-Tunl-ID
------------------------------------------------------------------------
1001 61440 10.20.1.1
1001 64944 10.20.1.2
------------------------------------------------------------------------Use the following command to display originating provider tunnels.
tools dump service id provider-tunnels type originating
========================================================================
VPLS 1001 Inclusive Provider Tunnels Originating
========================================================================
ipmsi (RSVP) P2MP-ID Tunl-ID Ext-Tunl-ID
------------------------------------------------------------------------
ipmsi-1001-73728 1001 61440 10.20.1.3
-----------------------------------------------------------------------Use the following command to display both originating and terminating provider tunnels.
tools dump service id provider-tunnels
========================================================================
VPLS 1001 Inclusive Provider Tunnels Originating
========================================================================
ipmsi (RSVP) P2MP-ID Tunl-ID Ext-Tunl-ID
------------------------------------------------------------------------
ipmsi-1001-73728 1001 61440 10.20.1.3
------------------------------------------------------------------------
========================================================================
VPLS 1001 Inclusive Provider Tunnels Terminating
========================================================================
ipmsi (RSVP) P2MP-ID Tunl-ID Ext-Tunl-ID
------------------------------------------------------------------------
1001 61440 10.20.1.1
1001 64944 10.20.1.2
-----------------------------------------------------------------------Use the following command to display both originating and terminating provider tunnels.
tools dump service id provider-tunnels===============================================================================
VPLS 10000 Inclusive Provider Tunnels Originating
===============================================================================
No Tunnels Found
-------------------------------------------------------------------------------
===============================================================================
VPLS 10000 Inclusive Provider Tunnels Terminating
===============================================================================
No Tunnels Found
-------------------------------------------------------------------------------
===============================================================================
VPLS 10000 Selective Provider Tunnels Originating
===============================================================================
spmsi (LDP) Source-Addr Group-Addr Root-Addr LSP-ID Lsp-Name
-------------------------------------------------------------------------------
10.0.0.4 239.0.0.4 192.0.2.4 8199 8199
* * 192.0.2.4 8197 8197
-------------------------------------------------------------------------------
===============================================================================
VPLS 10000 Selective Provider Tunnels Terminating
===============================================================================
spmsi (LDP) Source-Addr Group-Addr Root-Addr LSP-ID Lsp-Name
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------proxy-arp
proxy-arp
Syntax
proxy-arp [ip-address] [detail]
proxy-arp [ip-address] dynamic
Context
[Tree] (show>service>id proxy-arp)
Full Context
show service id proxy-arp
Description
This command displays, in a table, the existing proxy-ARP entries for a particular service. The table is populated by EVPN MAC routes that contain a MAC and an IP address, as well as static entries or dynamic entries from snooped ARP messages on access SAP or SDP-bindings.
A 7750 SR, 7450 ESS, or 7950 XRS that receives an ARP request from a SAP or SDP-binding performs a lookup in the proxy-ARP table for the service. If a match is found, the router replies to the ARP and does not allow ARP flooding in the VPLS service. If a match is not found, the ARP is flooded within the service if the configuration allows it.
The command allows for specific IP addresses to be displayed. Dynamic IP entries associated to a MAC list are displayed with the corresponding MAC list and resolve timers information.
Parameters
- ip-address
-
Specifies an IP address.
- detail
-
Displays detailed information.
- dynamic
-
Displays detailed information about dynamic entries.
Platforms
All
Output
Output Example*A:PE-3# show service id 5 proxy-arp
-------------------------------------------------------------------------------
Proxy Arp
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : enabled
Age Time : disabled Send Refresh : 120 secs
Table Size : 250 Total : 1
Static Count : 0 EVPN Count : 0
Dynamic Count : 1 Duplicate Count : 0
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Garp Flood : enabled Req Flood : enabled
Static Black Hole : disabled
EVPN Route Tag : 10
-------------------------------------------------------------------------------
*A:PE-3# show service id 5 proxy-arp detail
-------------------------------------------------------------------------------
Proxy Arp
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : enabled
Age Time : disabled Send Refresh : 120 secs
Table Size : 250 Total : 1
Static Count : 0 EVPN Count : 0
Dynamic Count : 1 Duplicate Count : 0
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Garp Flood : enabled Req Flood : enabled
Static Black Hole : disabled
EVPN Route Tag : 10
-------------------------------------------------------------------------------
===============================================================================
VPLS Proxy Arp Entries
===============================================================================
IP Address Mac Address Type Status Last Update
-------------------------------------------------------------------------------
10.0.0.1 00:ca:fe:ca:fe:01 dyn active 12/20/2016 12:38:28
-------------------------------------------------------------------------------
Number of entries : 1
===============================================================================
*A:PE-3# show service id 5 proxy-arp dynamic
===============================================================================
Proxy ARP Dyn Cfg Summary
===============================================================================
IP Addr Mac List
-------------------------------------------------------------------------------
10.0.0.1 list-1
-------------------------------------------------------------------------------
Number of Entries: 1
===============================================================================
*A:PE-3# show service id 5 proxy-arp dynamic 10.0.0.1
===============================================================================
Proxy ARP Dyn Cfg Detail
===============================================================================
IP Addr Mac List Resolve Time Remaining
(mins) Resolve Time
(secs)
-------------------------------------------------------------------------------
10.0.0.1 list-1 1 0
-------------------------------------------------------------------------------
Number of Entries: 1
===============================================================================
proxy-arp
Syntax
proxy-arp [ip-address ip-address] [ detail]
Context
[Tree] (show>service>id proxy-arp)
Full Context
show service id proxy-arp
Description
This command displays the proxy-ARP entries existing for a particular service. A 7750 SR, 7450 ESS or 7950 XRS router receiving an ARP request from a SAP or SDP-binding will perform a lookup in the proxy-arp table for the service. If the router finds a match, it will reply to the ARP and will not let the ARP be flooded in the VPLS service. If the router does not find a match, the ARP will be flooded within the service. The command allows for specific IP addresses to be shown.
The detail parameter allows the user to display all the entries. An individual IP address entry can also be shown.
Platforms
All
Output
The following output is an example of service proxy ARP information.
Output Example:PE71(1)# show service id 600 proxy-arp
-------------------------------------------------------------------------------
Proxy Arp
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : enabled
Age Time : 200 secs Send Refresh : 120 secs
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 3
Hold down : max
Anti Spoof MAC : 00:ca:ca:ca:ca:ca
EVPN
-------------------------------------------------------------------------------
Garp Flood : disabled Req Flood : disabled
-------------------------------------------------------------------------------
A:PE71(1)# show service id 600 proxy-arp detail
-------------------------------------------------------------------------------
Proxy Arp
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : enabled
Age Time : 200 secs Send Refresh : 120 secs
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 3
Hold down : max
Anti Spoof MAC : 00:ca:ca:ca:ca:ca
EVPN
-------------------------------------------------------------------------------
Garp Flood : disabled Req Flood : disabled
-------------------------------------------------------------------------------
===============================================================================
VPLS Proxy Arp Entries
===============================================================================
IP Address Mac Address Type Status Last Update
-------------------------------------------------------------------------------
172.16.0.1 00:ca:fe:ca:fe:02 evpn active 12/01/2014 12:02:27
172.16.0.61 00:ca:de:ba:ca:00 dyn active 12/01/2014 15:40:10
172.16.0.100 00:00:00:00:00:01 stat inActv 12/01/2014 12:01:57
172.16.0.102 00:00:00:00:00:02 stat inActv 12/01/2014 12:01:57
-------------------------------------------------------------------------------
Number of entries : 4
===============================================================================
A:PE71(1)#
proxy-arp
Syntax
proxy-arp
Context
[Tree] (tools>perform>service>id proxy-arp)
Full Context
tools perform service id proxy-arp
Description
Commands in this context provide proxy-arp tools.
Platforms
All
proxy-arp
Syntax
proxy-arp
proxy-arp duplicate [ip-address]
proxy-arp dynamic [ip-address]
Context
[Tree] (clear>service>id proxy-arp)
Full Context
clear service id proxy-arp
Description
This command allows all the duplicate or dynamic proxy-ARP entries to be cleared from the table. Individual IP entries can also be specified.
Platforms
All
proxy-arp
Syntax
proxy-arp usage
Context
[Tree] (tools>dump>service proxy-arp)
Full Context
tools dump service proxy-arp
Description
This command provides information about the usage and limit of the system-wide proxy-arp table for all the services. The command also shows if the limit has been exceeded and a trap raised.
Platforms
All
Output
Output Example*A:Dut# tools dump service proxy-arp usage
Proxy arp Usage
Current Usage : 10
System Limit : 511999
High Usage Trap Raised: No
High Usage Threshold: 95 percent
High Usage Clear Threshold: 90 percent
proxy-arp-nd
proxy-arp-nd
Syntax
proxy-arp-nd mac-list
proxy-arp-nd mac-list name
proxy-arp-nd mac-list name associations
Context
[Tree] (show>service proxy-arp-nd)
Full Context
show service proxy-arp-nd
Description
This command displays MAC address list information including MAC lists, MAC list details, and associations used in the proxy-arp-nd context.
Parameters
- name
-
Name of the MAC address list for which the detailed information is shown; the name can be up to 32 characters.
- associations
-
Mandatory keyword to display the service ID and dynamic IP to which the MAC list is associated.
Platforms
All
Output
Output Example*A:PE-3# show service proxy-arp-nd mac-list
===============================================================================
MAC List Information
===============================================================================
MAC List Name Last Change Num Macs Num Assocs
-------------------------------------------------------------------------------
list-1 12/20/2016 09:21:13 3 1
-------------------------------------------------------------------------------
Number of Entries: 1
===============================================================================
*A:PE-3# show service proxy-arp-nd mac-list "list-1"
===============================================================================
MAC List MAC Addr Information
===============================================================================
MAC Addr Last Change
-------------------------------------------------------------------------------
00:ca:fe:ca:fe:01 12/20/2016 09:21:13
00:ca:fe:ca:fe:02 12/20/2016 09:21:13
00:ca:fe:ca:fe:03 12/20/2016 09:21:13
-------------------------------------------------------------------------------
Number of Entries: 3
===============================================================================
*A:PE-3# show service proxy-arp-nd mac-list "list-1" associations
===============================================================================
MAC List Associations
===============================================================================
Service Id IP Addr
-------------------------------------------------------------------------------
5 10.0.0.1
-------------------------------------------------------------------------------
Number of Entries: 1
===============================================================================
proxy-db
proxy-db
Syntax
proxy-db [detail]
proxy-db group grp-ipv6-address
Context
[Tree] (show>service>id>mld-snooping proxy-db)
Full Context
show service id mld-snooping proxy-db
Description
This command displays proxy-reporting database entries.
Platforms
All
Output
The following output is an example of MLD snooping proxy database information.
Output Example*A:rbae_C# show service id 1 mld-snooping proxy-db
===============================================================================
MLD Snooping Proxy-reporting DB for service 1
===============================================================================
Group Address
Mode Up Time Num Sources
-------------------------------------------------------------------------------
FF04:db8:1
include 0d 00:01:01 1
FF04:db8:2
include 0d 00:01:00 1
-------------------------------------------------------------------------------
Number of groups: 2
===============================================================================
*A:rbae_C#
*A:rbae_C# show service id 1 mld-snooping proxy-db detail
===============================================================================
MLD Snooping Proxy-reporting DB for service 1
-------------------------------------------------------------------------------
MLD Group FF04::1
-------------------------------------------------------------------------------
Up Time : 0d 00:01:03 Mode : include
---------------------------------------------------------------------------
Source Address Up Time
---------------------------------------------------------------------------
2011:db8:1 0d 00:01:03
-------------------------------------------------------------------------------
MLD Group FF04:db8:2
-------------------------------------------------------------------------------
Up Time : 0d 00:01:02 Mode : include
---------------------------------------------------------------------------
Source Address Up Time
---------------------------------------------------------------------------
2011:db8:1 0d 00:01:02
-------------------------------------------------------------------------------
Number of groups: 2
===============================================================================
*A:rbae_C#
proxy-db
Syntax
proxy-db [detail]
proxy-db group grp-address
Context
[Tree] (show>service>id>igmp-snooping proxy-db)
Full Context
show service id igmp-snooping proxy-db
Description
This command displays information on the IGMP snooping proxy reporting database for the VPLS service.
Parameters
- grp-ip-address
-
Displays the IGMP snooping proxy reporting database for a specific multicast group address.
Platforms
All
Output
Output Example*A:ALA-1>show>service>id>snooping# proxy-db
===============================================================================
IGMP Snooping Proxy-reporting DB for service 10
===============================================================================
Group Address Mode Up Time Num Sources
-------------------------------------------------------------------------------
239.0.0.1 include 0d 00:05:40 2
-------------------------------------------------------------------------------
Number of groups: 1
===============================================================================
*A:ALA-1>show>service>id>snooping#
*A:ALA-1>show>service>id>snooping# proxy-db detail
===============================================================================
IGMP Snooping Proxy-reporting DB for service 10
-------------------------------------------------------------------------------
IGMP Group 239.0.0.1
-------------------------------------------------------------------------------
Up Time : 0d 00:05:54 Mode : include
------------------------------
Source Address Up Time
------------------------------
1.1.1.1 0d 00:05:54
1.1.1.2 0d 00:05:54
-------------------------------------------------------------------------------
Number of groups: 1
===============================================================================
*A:ALA-1>show>service>id>snooping#
IGMP Snooping proxy Fields describes the show output fields.
|
Label |
Description |
|---|---|
|
Group Address |
The IP multicast group address for which this entry contains information. |
|
Mode |
Specifies the type of membership report(s) received on the interface for the group. In the include mode, reception of packets sent to the specified multicast address is requested only from those IP source addresses listed in the source-list parameter of the IGMP membership report. In the "exclude” mode, reception of packets sent to the specified multicast address is requested from all IP source addresses except those listed in the source-list parameter. |
|
Up Time |
The total operational time in seconds. |
|
Num Sources |
Indicates the number of IGMP group and source specific queries received on this interface. |
|
Number of groups |
Number of IGMP groups. |
|
Source Address |
The source address for which this entry contains information. |
proxy-nd
proxy-nd
Syntax
proxy-nd [ipv6-address] [detail]
proxy-nd [ipv6-address] dynamic
Context
[Tree] (show>service>id proxy-nd)
Full Context
show service id proxy-nd
Description
This command displays, in a table, the existing proxy-ND entries for a particular service. The table is populated by the EVPN MAC routes containing a MAC and an IPv6 address, as well as static entries or dynamic entries from snooped NA messages on access SAP or SDP-bindings.
A 7750 SR, 7450 ESS, or 7950 XRS that receives a Neighbor Solicitation (NS) from a SAP or SDP-binding performs a lookup in the proxy-ND table for the service. If a match is found, the router replies to the NS and does not allow NS flooding in the VPLS service. If a match is not found, the NS is flooded in the service if the configuration allows it.
The command allows for specific IPv6 addresses to be shown. Dynamic IPv6 entries associated to a MAC list are shown with the corresponding MAC list and resolve timers information.
Parameters
- ipv6-address
-
Specifies an IPv6 address.
- detail
-
Displays detailed information.
- dynamic
-
Displays detailed information about dynamic entries.
Platforms
All
Output
The following output is an example of proxy ND information and Output Fields: show service proxy-nd detail <ipv6-address> describes the output fields.
Output ExampleA:node-2>show>service>id# proxy-nd
-------------------------------------------------------------------------------
Proxy ND
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : disabled
Age Time : disabled Send Refresh : 120 secs
Table Size : 250 Total : 2
Static Count : 1 EVPN Count : 1
Dynamic Count : 0 Duplicate Count : 0
Process DAD NS : enabled
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Unknown NS Flood : enabled ND Advertise : Host
Rtr Unsol NA Flood: enabled Host Unsol NA Fld : enabled
EVPN Route Tag : 0
-------------------------------------------------------------------------------The following output is an example of proxy ND detailed information and Output Fields: show service proxy-nd detail <ipv6-address> describes the output fields.
Output ExampleA:node-2>show>service>id# proxy-nd detail
-----------------------------------------------------------------------------
Proxy ND
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : disabled
Age Time : disabled Send Refresh : 120 secs
Table Size : 250 Total : 2
Static Count : 1 EVPN Count : 1
Dynamic Count : 0 Duplicate Count : 0
Process DAD NS : enabled
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Unknown NS Flood : enabled ND Advertise : Host
Rtr Unsol NA Flood: enabled Host Unsol NA Fld : enabled
EVPN Route Tag : 0
-------------------------------------------------------------------------------
===============================================================================
VPLS Proxy ND Entries
===============================================================================
IP Address Mac Address Type Status Flags Last Update
-------------------------------------------------------------------------------
2001:db8:15::4 00:ca:ca:00:00:04 stat active R I O 12/05/2022 15:20:34
2001:db8:15::5 00:ca:ca:00:00:05 evpn active R 12/05/2022 15:21:28
-------------------------------------------------------------------------------
Number of entries : 2
Legend : I=Immutable, O=Override, R=Router, H=Host
===============================================================================The following output is an example of proxy ND detailed information and Output Fields: show service proxy-nd detail <ipv6-address> describes the output fields.
Output ExampleA:node-2>show>service>id# proxy-nd detail
ipv6-address
-------------------------------------------------------------------------------
Proxy ND
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : disabled
Age Time : disabled Send Refresh : 120 secs
Table Size : 250 Total : 2
Static Count : 1 EVPN Count : 1
Dynamic Count : 0 Duplicate Count : 0
Process DAD NS : enabled
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Unknown NS Flood : enabled ND Advertise : Host
Rtr Unsol NA Flood: enabled Host Unsol NA Fld : enabled
EVPN Route Tag : 0
-------------------------------------------------------------------------------
IP Address : 2001:db8:15::4 MAC Address : 00:ca:ca:00:00:04
Type : stat Status : active
Rtr/Host : Rtr
Immutable : Yes EVPN Override : Yes|
Label |
Description |
|---|---|
| Proxy ND | |
|
Admin State |
The administrative state of proxy-nd |
|
Dyn Populate |
The addition of dynamic entries to the table |
|
Age Time |
The aging timer for proxy entries, where entries are flushed upon timer expiry |
|
Send Refresh |
The time at which to send a refresh message in seconds |
|
Table Size |
The maximum number of learned and static entries allowed in the proxy table of the service |
|
Total |
The total number of entries in the service |
|
Static Count |
The current number of static entries in the service |
|
EVPN Count |
The current number of EVPN entries in the service |
|
Dynamic Count |
The current number of dynamic entries in the service |
|
Duplicate Count |
The current number of duplicate entries in the service |
|
Process DAD NS |
The response to DAD neighbor solicitations |
| Dup Detect | |
|
Detect Window |
The window size in minutes |
|
Num Moves |
The number of moves required to declare a duplicate entry |
|
Hold down |
The hold-down time for a duplicate entry |
| Anti Spoof MAC |
The MAC address to replace the proxy-nd offending entry's MAC |
| EVPN | |
|
Unknown NS Flood |
Displays if unknown Neighbor Solicitation messages floods into the EVPN network |
|
ND Advertise |
The advertisement of static or dynamic entries that are learned as host or routers |
|
Rtr Unsol NA Flood |
Displays if system floods router unsolicited Neighbor Advertisements to EVPN |
|
Host Unsol NA Fld |
Displays if the system floods host unsolicited Neighbor Advertisements to the EVPN |
|
EVPN Route Tag |
The route tag of the entry |
|
IP Address |
The IP address of proxy-nd |
|
Mac Address |
The optional anti-spoof-mac to use |
|
Type |
The type of entry |
|
Status |
The status of entry |
| Rtr/Host | The static or dynamic entries are learned as host or routers |
| Immutable | - |
| EVPN Override | The EVPN override context |
The following output is an example of proxy ND dynamic information and Output Fields: show service proxy-nd dynamic describes the output fields.
Output ExampleA:node-2>show>service>id# proxy-nd dynamic
===============================================================================
Proxy ND Dyn Cfg Summary
===============================================================================
IP Addr Mac List
-------------------------------------------------------------------------------
2001:db8:1000::1 list-1
-------------------------------------------------------------------------------
Number of Entries: 1
===============================================================================The following output is an example of proxy ND dynamic information and Output Fields: show service proxy-nd dynamic describes the output fields.
Output ExampleA:node-2>show>service>id# proxy-nd dynamic
ipv6-address
==============================================================================
Proxy ND Dyn Cfg Detail
===============================================================================
IP Addr Mac List
Resolve Time(mins) Remaining Resolve Time(secs)
-------------------------------------------------------------------------------
2001:db8:1000::1 list-1
1 0
-------------------------------------------------------------------------------
Number of Entries: 1
===============================================================================|
Label |
Description |
|---|---|
| Proxy ND Dyn Cfg Summary | |
| IP Addr | The IP address of proxy-nd dynamic |
|
Mac List |
The MAC list for dynamic entry |
|
Resolve Time (mins) |
The resolve time in minutes |
|
Remaining Resolve Time (secs) |
The remaining resolve time in seconds |
|
Number of Entries |
The total number of entries |
proxy-nd
Syntax
proxy-nd
Context
[Tree] (tools>perform>service>id proxy-nd)
Full Context
tools perform service id proxy-nd
Description
Commands in this context provide proxy-nd tools.
Platforms
All
proxy-nd
Syntax
proxy-nd
proxy-nd duplicate [ipv6-address]
proxy-nd dynamic [ipv6-address]
Context
[Tree] (clear>service>id proxy-nd)
Full Context
clear service id proxy-nd
Description
This command allows all the duplicate or dynamic proxy-ND entries to be cleared from the table. Individual IPv6 entries can also be specified.
Platforms
All
proxy-nd
Syntax
proxy-nd usage
Context
[Tree] (tools>dump>service proxy-nd)
Full Context
tools dump service proxy-nd
Description
This command provides information about the usage and limit of the system-wide proxy-nd table for all the services. The command also shows if the limit has been exceeded and a trap raised.
Platforms
All
Output
Output Example*A:Dut# tools dump service proxy-nd usage
Proxy nd Usage
Current Usage : 0
System Limit : 511999
High Usage Trap Raised: No
High Usage Threshold: 95 percent
High Usage Clear Threshold: 90 percent
psb
psb
Syntax
psb [endpoint endpoint-address] [sender sender-address] [tunnelid tunnel-id] [lspid lsp-id] [detail] [status {up | down}]
Context
[Tree] (tools>dump>router>rsvp psb)
Full Context
tools dump router rsvp psb
Description
This command displays path state block (PSB) information for RSVP.
When a PATH message arrives at an LSR, the LSR stores the label request in the local PSB for the LSP. If a label range is specified, the label allocation process assigns a label from that range.
The PSB contains the IP address of the previous hop, and the session, sender, and TSPEC. This information is used to route the corresponding RESV message back to LSR 1.
Parameters
- endpoint endpoint-address
-
Specifies the IP address of the last hop.
- sender sender-address
-
Specifies the IP address of the sender.
- tunnelid tunnel-id
-
Specifies the SDP ID.
- lspid lsp-id
-
Specifies the label switched path that is signaled for this entry.
- detail
-
Displays detailed RSVP PSB information.
- status {up | down}
-
Specifies the LSP status.
Platforms
All
Output
The following output is an example of MPLS RSVP PSB information.
Output Example*A:Dut-C# tools dump router rsvp psb detail
--------------------------------------------------------------------------------
PSB:
P2P: Session (To: 10.20.1.6 - 6 - 10.20.1.3), Sender (10.20.1.3 - 41986) PHop 0.0.0
.0
PSB CurrState: PRIMARYS_CONNECTED PrevState: PRIMARYS_INIT Flags: 0x0
LocalLabel 0 OutLabel 524277
Incoming IfIndex: Interface: Local API(-1)
Refresh interval 5, Send Path refresh in 1 secs, Path Refresh timeout 0 secs
PrevHop: Ctype 1 Addr 0.0.0.0, LIH 0
DnStream Nbr: Addr-> 10.10.11.4 IfIndex ip-10.10.11.3(5)
UpStream Neighbor is NULLP
Session Attribute:
Session Name: 6::6
HoldPri: 0 SetupPri: 7 Flags: 0x6
Ctype: 7, IncludeGroup: 0x0 IncludeAllGroup: 0x0 ExcludeGroup: 0x0
ClassType: Absent
TSpec: Flags 0x8000 QOSC 1, PDR (infinity), PBS 0.000 bps, CDR (0.000 bps) MTU: 150
0
CSPF Hop List: ->
(1) Ipv4Addr 10.10.11.3 RtrId 10.20.1.3 EgrAdmGrp 0x0 (Strict)
(2) Ipv4Addr 10.10.11.4 RtrId 10.20.1.4 EgrAdmGrp 0x0 (Strict)
(3) Ipv4Addr 10.10.9.6 RtrId 10.20.1.6 EgrAdmGrp 0x0 (Strict)
PSB RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.11.3(10.20.1.3)
PSB SENT RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.11.3(0.0.0.0)
PSB FILTERSPEC RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.11.4(10.20.1.4)
(2) * Flags : 0x1 : Global
(2) * Label : 524277
(3) * Flags : 0x0 : I
(3) * IPv4 -> 10.10.9.6(10.20.1.6)
(4) * Flags : 0x1 : Global
(4) * Label : 524279
PSB ERO : ->
(1) IPv4Prefix 10.10.11.4/32, Strict
(2) IPv4Prefix 10.10.9.6/32, Strict
PSB SENT ERO : ->
(1) IPv4Prefix 10.10.11.4/32, Strict
(2) IPv4Prefix 10.10.9.6/32, Strict
SendTempl: Sender:10.20.1.3_41986
Sent AdSpec: Flags 0x2
AdSpec General
- Service Break bit : 0x0
- IS Hop Count : 0x0
- Path Bandwidth Estimate : 0x0
- Minimum Path latency : 0xffffffff
- Composed path MTU : 1500
AdSpec Controlled Load
- Service Break bit : 0x0
Num Paths Received :0
Num Paths Transmitted:6
Num Resvs Received :7
Num Resvs Transmitted:0
Num Summmary Paths Received :0
Num Summmary Paths Transmitted:0
Num Summmary Resvs Received :0
Num Summmary Resvs Transmitted:0
Created at 1804 (26 secs back)
--------------------------------------------------------------------------------
Total PSB Count : 1
*A:Dut-C#
*A:Dut-D# show router mpls lsp transit
===============================================================================
MPLS LSPs (Transit)
===============================================================================
Legend : @ - Active Detour
===============================================================================
From To In I/F Out I/F State LSP Name
-------------------------------------------------------------------------------
10.20.1.3 10.20.1.6 1/1/4 1/1/2 Up
6::6
-------------------------------------------------------------------------------
LSPs : 1
-------------------------------------------------------------------------------
*A:Dut-D# tools dump router rsvp psb detail
--------------------------------------------------------------------------------
PSB:
P2P: Session (To: 10.20.1.6 - 6 - 10.20.1.3), Sender (10.20.1.3 - 41986) PHop 10.10
.11.3
PSB CurrState: PRIMARYS_CONNECTED PrevState: PRIMARYS_INIT Flags: 0x0
LocalLabel 524277 OutLabel 524279
Incoming IfIndex: ip-10.10.11.4(5)
Refresh interval 5, Send Path refresh in 3 secs, Path Refresh timeout 24 secs
Send Resv refresh in 4 secs
PrevHop: Ctype 1 Addr 10.10.11.3, LIH 5
DnStream Nbr: Addr-> 10.10.9.6 IfIndex ip-10.10.9.4(3)
UpStream Nbr: Addr-> 10.10.11.3 IfIndex ip-10.10.11.4(5)
Session Attribute:
Session Name: 6::6
HoldPri: 0 SetupPri: 7 Flags: 0x6
Ctype: 7, IncludeGroup: 0x0 IncludeAllGroup: 0x0 ExcludeGroup: 0x0
ClassType: Absent
TSpec: Flags 0x8000 QOSC 1, PDR (infinity), PBS 0.000 bps, CDR (0.000 bps) MTU: 150
0
PSB RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.11.3(0.0.0.0)
PSB SENT RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.9.4(0.0.0.0)
(2) * Flags : 0x0 : I
(2) * IPv4 -> 10.10.11.3(0.0.0.0)
PSB FILTERSPEC RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.9.6(0.0.0.0)
(2) * Flags : 0x1 : Global
(2) * Label : 524279
PSB ERO : ->
(1) IPv4Prefix 10.10.11.4/32, Strict
(2) IPv4Prefix 10.10.9.6/32, Strict
PSB SENT ERO : ->
(1) IPv4Prefix 10.10.9.6/32, Strict
SendTempl: Sender:10.20.1.3_41986
Received AdSpec: Flags 0x2
AdSpec General
- Service Break bit : 0x0
- IS Hop Count : 0x0
- Path Bandwidth Estimate : 0x0
- Minimum Path latency : 0xffffffff
- Composed path MTU : 1500
AdSpec Controlled Load
- Service Break bit : 0x0
Sent AdSpec: Flags 0x2
AdSpec General
- Service Break bit : 0x0
- IS Hop Count : 0x0
- Path Bandwidth Estimate : 0x0
- Minimum Path latency : 0xffffffff
- Composed path MTU : 1500
AdSpec Controlled Load
- Service Break bit : 0x0
Num Paths Received :12
Num Paths Transmitted:12
Num Resvs Received :13
Num Resvs Transmitted:14
Num Summmary Paths Received :0
Num Summmary Paths Transmitted:0
Num Summmary Resvs Received :0
Num Summmary Resvs Transmitted:0
Created at 1786 (55 secs back)
--------------------------------------------------------------------------------
Total PSB Count : 1
*A:Dut-D#
*A:Dut-F# show router mpls lsp terminate
===============================================================================
MPLS LSPs (Terminate)
===============================================================================
Legend : @ - Active Detour
===============================================================================
From To In I/F Out I/F State LSP Name
-------------------------------------------------------------------------------
10.20.1.3 10.20.1.6 1/1/1 n/a Up
6::6
-------------------------------------------------------------------------------
LSPs : 1
-------------------------------------------------------------------------------
*A:Dut-F# tools dump router rsvp psb detail
--------------------------------------------------------------------------------
PSB:
P2P: Session (To: 10.20.1.6 - 6 - 10.20.1.3), Sender (10.20.1.3 - 41986) PHop 10.10
.9.4
PSB CurrState: PRIMARYS_CONNECTED PrevState: PRIMARYS_IDLE Flags: 0x0
LocalLabel 524279 OutLabel 0
Incoming IfIndex: ip-10.10.9.6(2)
Refresh interval 5, Send Path refresh in 0 secs, Path Refresh timeout 23 secs
Send Resv refresh in 3 secs
PrevHop: Ctype 1 Addr 10.10.9.4, LIH 3
DnStream, Nbr: Addr-> 0.0.0.0 IfIndex Interface: Local API(-1)
UpStream Nbr: Addr-> 10.10.9.4 IfIndex ip-10.10.9.6(2)
Session Attribute:
Session Name: 6::6
HoldPri: 0 SetupPri: 7 Flags: 0x6
Ctype: 7, IncludeGroup: 0x0 IncludeAllGroup: 0x0 ExcludeGroup: 0x0
ClassType: Absent
TSpec: Flags 0x8000 QOSC 1, PDR (infinity), PBS 0.000 bps, CDR (0.000 bps) MTU: 150
0
PSB RRO : ->
(1) * Flags : 0x0 : I
(1) * IPv4 -> 10.10.9.4(0.0.0.0)
(2) * Flags : 0x0 : I
(2) * IPv4 -> 10.10.11.3(0.0.0.0)
PSB SENT RRO : ->
NULL RRO
PSB FILTERSPEC RRO : ->
NULL RRO
PSB ERO : ->
(1) IPv4Prefix 10.10.9.6/32, Strict
SendTempl: Sender:10.20.1.3_41986
Received AdSpec: Flags 0x2
AdSpec General
- Service Break bit : 0x0
- IS Hop Count : 0x0
- Path Bandwidth Estimate : 0x0
- Minimum Path latency : 0xffffffff
- Composed path MTU : 1500
AdSpec Controlled Load
- Service Break bit : 0x0
Num Paths Received :16
Num Paths Transmitted:0
Num Resvs Received :0
Num Resvs Transmitted:18
Num Summmary Paths Received :0
Num Summmary Paths Transmitted:0
Num Summmary Resvs Received :0
Num Summmary Resvs Transmitted:0
Created at 1773 (74 secs back)
--------------------------------------------------------------------------------
Total PSB Count : 1
ptp
ptp
Syntax
ptp
Context
[Tree] (show>service>id ptp)
Full Context
show service id ptp
Description
This command displays Precision Timing Protocol (PTP) information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following command shows PTP service information and Output Fields: show service id <id> ptp describes the output fields.
show service id ptp-------------------------------------------------------------------------------
PTP Configuration
-------------------------------------------------------------------------------
Admin State : up Oper State : up
Peer Limit : none
===============================================================================
|
Label |
Description |
|---|---|
|
Admin State |
The administrative state of PTP |
|
Oper State |
The operational state of PTP |
|
Peer Limit |
The maximum number of PTP peers that the system may create automatically |
ptp
Syntax
ptp
Context
[Tree] (show>system ptp)
Full Context
show system ptp
Description
This command displays Precision Time Protocol (PTP) configuration and state information. This information can be displayed for the entire node or on a per router instance basis.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of PTP information, and System PTP Field Descriptions describes the output fields.
Output Exampleshow system ptp==============================================================================
IEEE 1588/PTP Clock Information
===============================================================================
-------------------------------------------------------------------------------
Local Clock
-------------------------------------------------------------------------------
Clock Type : boundary PTP Profile : ITU-T G.8275.2
Domain : 44 Network Type : sdh
Admin State : up Oper State : up
Announce Interval : 1 pkt/2 s Announce Rx Timeout: 3 intervals
Peer Limit : none (Base Router)
G.8275 Priority : 128 PTSF-unusable : n/a
Clock Id : e48184fffeae2b34 Clock Class : 165
Clock Accuracy : unknown Clock Variance : ffff (not computed)
Clock Priority1 : 128 Clock Priority2 : 128
Steps Removed : 11
Sync Uncertain : true Reason Uncertain : PTP time not locked
TxWhileSyncUncert : true
-------------------------------------------------------------------------------
Parent Clock
-------------------------------------------------------------------------------
Port : A/gnss
Parent Clock Id : ca47fffffe000000 Remote PTP Port : 65534
GM Clock Id : ca47fffffe000000 GM Clock Class : 6
GM Clock Accuracy : within 100 ns GM Clock Variance : 0x4e5d (1.8E-15)
GM Clock Priority1: 128 GM Clock Priority2 : 128
Sync Uncertain : false
-------------------------------------------------------------------------------
Backup Clock Source
-------------------------------------------------------------------------------
IP Address : 1.1.1.1
Router : Base
-------------------------------------------------------------------------------
Time Properties
-------------------------------------------------------------------------------
Timescale : PTP
Frequency Traceable : yes
Time Traceable : yes
Time Source : GPS
UTC Offset : +37 seconds
Leap Second : no leap second pending
-------------------------------------------------------------------------------
Central Frequency Clock
-------------------------------------------------------------------------------
Status : locked Quality : prc
Reference Selected : ptp
-------------------------------------------------------------------------------
PTP Frequency Recovery
-------------------------------------------------------------------------------
Frequency Recovery State : locked Changed : 2022/01/15 03:58:10
Frequency Offset : +53.931 ppb
-------------------------------------------------------------------------------
PTP Time Recovery
-------------------------------------------------------------------------------
Current Time : 2022/01/15 07:23:57.7 (UTC)
Time Recovery State : locked Changed : 2022/01/15 07:11:15
Last Packet Offset From Master : +7,628 ns Last Calc: 2022/01/15 07:23:59
Last Packet Mean Path Delay : +32,563 ns Last Calc: 2022/01/15 07:23:59
Last Adjustment : +33 ns Last Calc: 2022/01/15 07:23:59
===============================================================================
|
Label |
Description |
|---|---|
|
Local Clock |
|
|
Clock Type |
The type of clock of the network element.
|
|
PTP Profile |
The Precision Time Protocol (PTP) profile specifies the standard to which PTP conforms
|
|
Domain |
The domain in which PTP 1588 runs on the system |
|
Network Type |
The SR OS is configured to use PTP clock classes corresponding to either SONET or SDH quality levels |
|
Admin State |
The administrative state of PTP |
|
Oper State |
The operational state of PTP |
|
Announce Interval |
The packet rate requested in REQUEST_UNICAST_TRANSMISSION signaling messages for announce packets |
|
Announce Rx Timeout |
The number of announce intervals that have to occur without receiving a PTP announce message before the PTP event ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES occurs |
|
Peer Limit |
The maximum number of PTP peers that may be automatically created by the system on this router instance |
|
G.8275.1 Priority |
The priority used in the best TimeTransmitter clock algorithm for the local (internal) PTP port when Clock Profile is g8275dot1-2014 |
|
PTSF-unusable |
The PTSF unusable administrative state |
|
Clock ID |
The clock Identity value of the local PTP clock (defaultDS) |
|
Clock Class |
The clockClass value of the local PTP clock (defaultDS) |
|
Clock Accuracy |
The clockAccuracy value accuracy of the local PTP clock (defaultDS) |
|
Clock Variance |
The offsetScaledLogVariance value of the local PTP clock (defaultDS) |
|
Clock Priority1 |
The priority1 value of the local PTP clock (defaultDS) |
|
Clock Priority2 |
The priority2 value of the local PTP clock (defaultDS) |
|
Steps Removed |
The steps removed value used in Announce messages sent from this PTP clock |
|
Sync Uncertain |
For the local clock: the value of the synchronization uncertainty that is used in Announce messages transmitted by this node. For the parent clock: the value received in the Announce messages from that clock. |
|
Reason Uncertain |
Provides an explanation for a Sync Uncertain true indication.
|
|
TxWhileSyncUncertain |
The value of the tx-while-sync-uncertain configuration item |
|
PTP Port State |
The PTP port state. Only shown for ordinary clocks which contain only one PTP port |
|
Last Changed |
The date and time of the last change of the PTP port state |
|
Parent Clock |
|
|
Port |
The port that is being used as a backup to a local GNSS time source |
|
Remote MAC Address |
The MAC address of the parent clock port sending PTP message to the local PTP clock |
|
Parent Clock ID |
The clock Identity of the parent clock |
|
Remote PTP Port |
The port number of the PTP port on the parent clock that is used to communicate with the local PTP clock |
|
Local Clock is Parent Clock |
Displayed if there is no external parent clock |
|
GM Clock Id |
The clockIdentity value of the grandmaster clock advertised by the parent clock |
|
GM Clock Class |
The clockClass value of the grandmaster clock advertised by the parent clock |
|
GM Clock Accuracy |
The clockAccuracy value of the grandmaster clock advertised by the parent clock |
|
GM Clock Variance |
The offsetScaledLogVariance value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority1 |
The priority1 value of the grandmaster clock advertised by the parent clock |
|
GM Clock Priority2 |
The priority2 value of the grandmaster clock advertised by the parent clock |
|
Backup Clock Source |
|
|
IP Address |
The address of the external clock that is being used as a backup to a local GNSS time source |
|
Router |
The routing instance that contains the external PTP clock being used as a backup |
|
Time Properties |
|
|
Timescale |
The time scale of the time distributed by PTP |
|
Frequency Traceable |
Indicates if the time distributed by PTP is traceable a primary reference |
|
Time Traceable |
Indicates if the time distributed by PTP is traceable to a primary reference |
|
Time Source |
The source of time used by the grandmaster clock |
|
UTC Offset |
The current offset between the International Atomic Time (TAI) and Universal Coordinated Time (UTC) timescales |
|
Leap Second |
Indicates if there is a leap second pending |
|
Central Frequency Clock |
|
|
Status |
The state of the central frequency clock |
|
Quality |
The quality level of the source into the central frequency clock |
|
Reference Selected |
The reference currently in use as the source into the central frequency clock |
|
PTP Frequency Recovery |
|
|
Frequency Recovery State |
The state of the frequency recovery algorithm.
|
|
Last Changed |
The date and time of the last change of the PTP Recovery State |
|
Frequency Offset |
The offset computed by the frequency recovery algorithm required to align the local oscillator to the frequency of the parent clock. The value is provided in parts per billion. Positive values indicate that the recovered clock is faster than nominal, and negative values indicate that the recovered clock is slower than nominal. |
|
PTP Time Recovery |
|
|
Current Time |
The date and time. If the timescale is PTP, then the time is converted to UTC time based on the current offset between UTC and PTP time. |
|
Time Recovery State |
The state of the time recovery algorithm.
|
|
Last Packet Offset From Master |
The offsetFromMaster calculated from the last packet exchange with the parent clock |
|
Last Calc |
The time at which the previous field was calculated |
|
Last Packet Mean Path Delay |
The meanPathDelay calculated from the last packet exchange with the parent clock |
|
Last Adjustment |
The nanosecond change to the local time scale that last came out of the time recovery algorithm |
ptp
ptsf-unusable
ptsf-unusable
Syntax
ptsf-unusable
Context
[Tree] (clear>system>ptp>port>neighbor ptsf-unusable)
Full Context
clear system ptp port neighbor ptsf-unusable
Description
This command clears the PTSF-unusable condition from the neighbor PTP clock.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
public-static-devices
public-static-devices
Syntax
public-static-devices [mac ieee-address]
Context
[Tree] (show>subscr-mgmt>vrgw>brg>gateway public-static-devices)
Full Context
show subscriber-mgmt vrgw brg gateway public-static-devices
Description
This command displays public static device mappings.
Parameters
- ieee-address
-
Specifies the MAC address, up to 30 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
pw
pw
Syntax
pw
Context
[Tree] (tools>perform>service>id>admin-lock pw)
[Tree] (tools>perform>service>id>loopback pw)
Full Context
tools perform service id admin-lock pw
tools perform service id loopback pw
Description
In the admin-lock context, this command administratively locks the specified spoke SDP by locking the host service. The command must be executed at both ends of the PW or MS-PW represented by the spoke SDP. Test traffic can then be injected using a test SAP.
In the loopback context, this command enters the MPLS-TP PW context for starting or stopping a loopback on a specified spoke SDP. An administrative lock should first be applied to both ends of the PW or MS-PW represented by the spoke SDP prior to configuring the loopback.
Loopback functions for MPLS-TP pseudowire can be specified for either a T-PE or S-PE.
Platforms
All
pw-port
pw-port
Syntax
pw-port [pw-port-id] [detail]
pw-port sdp sdp-id
pw-port sdp none
pw-port [pw-port-id] statistics
Context
[Tree] (show pw-port)
Full Context
show pw-port
Description
Displays pseudo-wire port information.
If no optional parameters are specified, the command displays a summary of all defined PW ports. The optional parameters restrict output to only ports matching the specified properties.
Parameters
- pw-port-id
-
Specifies the pseudo-wire port identifier.
- detail
-
Displays detailed port information that includes all the pw-port output fields.
- sdp-id
-
The SDP ID for which to display matching PW port information.
- statistics
-
Displays port statistics information.
Platforms
All
Output
The following outputs are example of PW port information.
Output Example#show pw-port
============================================================================
PW Port Information
============================================================================
PW Port Encap SDP IfIndex VC-Id
----------------------------------------------------------------------------
1 dot1q 1 1526726657 1
2 qinq 1 1526726658 2
3 dot1q 1 1526726659 3
4 qinq 1 1526726660 4
============================================================================
#show pw-port 3
============================================================================
PW Port Information
============================================================================
PW Port Encap SDP IfIndex VC-Id
----------------------------------------------------------------------------
3 dot1q 1 1526726659 3
============================================================================
#show pw-port sdp none
============================================================================
PW Port Information
============================================================================
PW Port Encap SDP IfIndex VC-Id
----------------------------------------------------------------------------
5 dot1q 1526726661
============================================================================
#show pw-port sdp 1
============================================================================
PW Port Information
============================================================================
PW Port Encap SDP IfIndex VC-Id
----------------------------------------------------------------------------
1 dot1q 1 1526726657 1
2 qinq 1 1526726658 2
3 dot1q 1 1526726659 3
4 qinq 1 1526726660 4
============================================================================
Show PW-Port Output Fields describes the pw-port output fields.
|
Label |
Description |
|---|---|
|
PW Port |
The PW port identifier |
|
Encap |
The encapsulation type of the PW port |
|
SDP |
The SDP identifier |
|
IfIndex |
The interface index used for the PW port |
|
VC-Id |
The Virtual Circuit identifier |
#show pw-port 10 detail
===============================================================================
PW Port Information
===============================================================================
PW Port : 10
Encap : dot1q
SDP : 1
IfIndex : 1526726666
VC-Id : 2
Description : PW Port
Dot1Q Ethertype : 0x8100
Service ID : 20211
Down on Peer Tldp PW Status Faults: No
Oper Up on MH Standby : No
===============================================================================
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 10)
===============================================================================
SDP Binding port : 1/1/c1/3
VC-Id : 2 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Dot1Q Ethertype : 0x8100
Control Word : Not Preferred
Entropy Label : Enabled
Service MTU : default
Admin Ingress label : None Admin Egress label : None
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
#show service id 2147483649 sdp 1:2 detail
===============================================================================
Service Destination Point (Sdp Id : 1:2) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 1:2 -(10.20.1.2)
-------------------------------------------------------------------------------
Description : Default sdp description
SDP Id : 1:2 Type : Spoke
Spoke Descr : (Not Specified)
Split Horiz Grp : (Not Specified)
Etree Root Leaf Tag: Disabled Etree Leaf AC : Disabled
VC Type : Ether VC Tag : n/a
Admin Path MTU : 0 Oper Path MTU : 1514
Delivery : MPLS
Far End : 10.20.1.2 Tunnel Far End :
Oper Tunnel Far End: 10.20.1.2
LSP Types : LDP
Hash Label : Disabled Hash Lbl Sig Cap : Disabled
Oper Hash Label : Disabled
Entropy Label : Enabled
Admin State : Up Oper State : Up
MinReqd SdpOperMTU : n/a
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 524276 Egress Label : 524281
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
BFD Template : None
BFD-Enabled : no BFD-Encap : ipv4
BFD Fail Action : none BFD Oper State : notConfigured
BFD WaitForUpTimer : 0 secs
BFD Time Remain : 0 secs
Last Status Change : 03/29/2021 14:47:13 Signaling : TLDP
Last Mgmt Change : 03/29/2021 14:47:13
Endpoint : N/A Precedence : 4
PW Status Sig : Enabled
Force Vlan-Vc : Disabled Force Qinq-Vc : none
Class Fwding State : Down
Local Pw Bits : None
Peer Pw Bits : None
Peer Fault Ip : None
Application Profile: None
Transit Policy : None
MAC Pinning : Disabled
Oper Group : (none) Monitor Oper Grp : (none)
Ingress Qos Policy : (none) Egress Qos Policy : (none)
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
LDP Information :
-------------------------------------------------------------------------------
LDP LSP Id : 65537
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn
Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : disabled
OSPF : disabled
TE-LSP : disabled
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
Show PW-Port Detail Output Fields describes the pw-port detail output fields.
|
Label |
Description |
|---|---|
|
PW Port |
The PW port identifier. |
|
Encap |
The encapsulation type of the PW port. |
|
SDP |
The SDP identifier |
|
IfIndex |
The interface index used for the PW port |
|
VC-Id |
The virtual circuit identifier |
|
Description |
The description of the PW port |
|
Dot1Q Ethertype |
The Dot1Q ethernet type |
|
Service Id |
The service ID |
|
Down on Peer Tldp PW Status Faults |
The down on peer TLDP PW status faults |
|
Oper Up on MH Standby |
The operational up status on MH standby |
|
I. Fwd. Pkts |
The number of forwarded packets ingressing this PW port |
|
I. Fwd. Octs |
The number of forwarded octets ingressing this PW port |
|
E. Fwd. Pkts |
The number of forwarded packets egressing this PW port |
|
I. Dro. Pkts |
The number of dropped packets on ingress |
|
I. Dro. Octs |
The number of dropped octets on ingress |
|
E. Fwd. Octets |
The number of forwarded octets egressing this PW port |
The following outputs are examples of VSR PW port information.
Output ExampleThe following output is an example using the L2oGRE tunnel type for the VSR only.
show pw-port 10
===================================================================
PW Port Information
===================================================================
PW Port Encap SDP:VC-Id IfIndex Epipe
-------------------------------------------------------------------
10 dot1q N/A 1526726666 10239
===================================================================
show pw-port 10
=====================================================================
PW Port Information
=====================================================================
PW Port Encap SDP:VC-Id IfIndex
---------------------------------------------------------------------
10 dot1q 1:2 1526726666
=====================================================================
The following output is an example using the MPLS tunnel type for the VSR only.
*A:Dut-C# show pw-port 10
=====================================================================
PW Port Information
=====================================================================
PW Port Encap SDP:VC-Id IfIndex
---------------------------------------------------------------------
10 dot1q 17281:100010 1526726666
=====================================================================
*A:vSIM# show pw-port 1 statistics
===============================================================================
Pw-Port 1
===============================================================================
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 22514728 E. Fwd. Octets : 22424666292
Grp Enc Stats :
I. Dro. Inv. Spi. : 0 I. Dro. OthEncPkts.: 0
E. Dro. Enc. Pkts. : 0
The following output is an example of the PW port statistics output for the VSR only.
*A:Dut-B# show pw-port 10 statistics
===============================================================================
Pw-Port 10
===============================================================================
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
Grp Enc Stats :
I. Dro. Inv. Spi. : 0 I. Dro. OthEncPkts.: 0
E. Dro. Enc. Pkts. : 0
The following table describes the show pw-port output fields.
|
Label |
Description |
|---|---|
|
PW Port |
The PW port identifier |
|
Encap |
The encapsulation type of the PW port |
|
SDP:VD-Id |
This field is not applicable to the Flex PW port |
|
IfIndex |
The interface index used for the PW port |
|
Epipe |
The ID of the Epipe service in which this PW port is configured. The tunnel type that is terminated on this PW port can be determined from the Epipe. |
|
Description |
The description string for the PW port |
|
Service Id |
The ID of the Epipe service in which this PW port is configured |
|
Admin Status |
The Admin status of the SDP |
|
Oper Status |
The operational status of the SDP |
|
I. Fwd. Pkts. |
The number of forwarded packets ingress in this PW port |
|
I. Fwd. Octs. |
The number of forwarded octets ingressing this PW port |
|
E. Fwd. Pkts. |
The number of forwarded packets egressing this PW port |
|
I. Dro. Pkts. |
The number of dropped packets on ingress |
|
I. Dro. Octs. |
The number of dropped octets on ingress |
|
E. Fwd. Octets. |
The number of forwarded octets egressing this PW port |
|
Grp Enc Stats |
Not applicable to Flex PW port |
pw-port
Syntax
pw-port [pw-port-id] [detail]
pw-port sdp sdp-id
pw-port sdp none
pw-port pw-port-id statistics
Context
[Tree] (show pw-port)
Full Context
show pw-port
Description
This command displays FPE-based PW-port configuration information, state information and forwarding statistics.
Parameters
- pw-port-id
-
Specifies the PW-port ID.
- sdp-id
-
Displays PW port information based on the known internal SDP ID
- sdp none
-
Displays information about FPE-based PW-ports that are not associated with any internal SDPs
- statistics
-
Displays forwarding statistics, such as the number or forwarded or dropped frames (Ethernet, VLANs, payload)
Platforms
All
Output
The following output is an example of PW port information.
PW-Port Field Descriptions describes the show pw-port command output fields.
Output Example*A:vSIM# show pw-port 1
===================================================================
PW Port Information
===================================================================
PW Port Encap SDP IfIndex VC-Id
-------------------------------------------------------------------
1 dot1q 17406 1526726657 100001
*A:vSIM# show pw-port 1 detail
===============================================================================
PW Port Information
===============================================================================
PW Port : 1
Encap : dot1q
SDP : 17406
IfIndex : 1526726657
VC-Id : 100001
Description : test
===============================================================================
===============================================================================
Service Destination Point (Sdp Id 17406 Pw-Port 1)
===============================================================================
SDP Binding port : pxc-1.b
VC-Id : 100001 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Admin Ingress label : 262142 Admin Egress label : 262143
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
*A:vSIM# show pw-port 1 statistics
===============================================================================
Service Destination Point (Sdp Id 17406 Pw-Port 1)
===============================================================================
SDP Binding port : pxc-1.b
VC-Id : 100001 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Admin Ingress label : 262142 Admin Egress label : 262143
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
*A:vSIM# show pw-port sdp 17406
===================================================================
PW Port Information
===================================================================
PW Port Encap SDP IfIndex VC-Id
-------------------------------------------------------------------
1 dot1q 17406 1526726657 100001
*A:vSIM# show pw-port sdp none
===================================================================
PW Port Information
===================================================================
PW Port Encap SDP IfIndex VC-Id
-------------------------------------------------------------------
2 dot1q 1526726658
===========================================================
|
Label |
Description |
|---|---|
|
PW-Port |
Displays the PW port ID. |
|
Encap |
Displays the PW port encapsulation (dot1q or qinq). |
|
SDP |
Displays the Internal SDP to which this PW port is bound. |
|
IfIndex |
Displays the Internal interface index. |
|
VC-Id |
Displays the VC-id of the internal spoke SDP that interconnects external PW to this PW port. |
|
Description |
Displays the description of this PW port. |
|
SDP Binding Port |
Displays the PXC sub-port to which this PW port is bound. This is termination side of PXC, always denoted as .b side. |
|
VC Type |
Displays the VC type of the PW port. |
|
Admin Status |
Displays the admin status of the internal SDP. |
|
Oper Status |
Displays the operational status of the internal SDP. |
|
Admin Ingress Label |
Displays the ingress VC-label associated with this PW port. |
|
Admin Egress Label |
Displays the egress VC-label associated with this PW port. |
|
Oper Flags |
Displays the operational flags on the internal SDP. |
|
Monitor Oper-Group |
Displays the operational group that is being monitored by this PW port. |
|
I. Fwd. Pkts. |
Displays the number of forwarded packets ingressing this PW port. |
|
I. Fwd. Octs. |
Displays the number of forwarded octets ingressing this PW port. |
|
E. Fwd. Pkts. |
Displays the number of forwarded packets egressing this PW port. |
|
I. Dro. Pkts. |
Displays the number of dropped packets on ingress. |
|
I. Dro. Octs. |
Displays the number of dropped octets on ingress. |
|
E. Fwd. Octets. |
Displays the number of forwarded octets egressing this PW port. |
pw-port
Syntax
pw-port pw-port-id statistics
Context
[Tree] (clear pw-port)
Full Context
clear pw-port
Description
This command clears PW port statistics for the specified ID.
Platforms
All
pw-port-list
pw-port-list
Syntax
pw-port-list
Context
[Tree] (show>service>system pw-port-list)
Full Context
show service system pw-port-list
Description
This command displays system PW port list information.
Platforms
VSR
Output
The following output is an example of system pw-port-list information.
Output Example*A:Dut-B>config>service>system# show service system pw-port-list
===============================================================================
PW Port List
===============================================================================
Ports
-------------------------------------------------------------------------------
1/1/1
1/1/2
1/1/3
1/1/4
1/1/5
1/1/6
-------------------------------------------------------------------------------
Number of Entries: 6
===============================================================================
pw-sap-using
pw-sap-using
Syntax
pw-sap-using
Context
[Tree] (show>service pw-sap-using)
Full Context
show service pw-sap-using
Description
This command displays service SAP PW port information.
Platforms
All
Output
The following output is an example of PW SAP port information.
Output Example===============================================================================
Service Access Points
===============================================================================
PortId SvcId Ing. Ing. Egr. Egr. Adm Opr
QoS Fltr QoS Fltr
-------------------------------------------------------------------------------
pw-1:0 1 1 none 1 none Up Up
pw-1:1 1 1 none 1 none Up Up
pw-2:2.1 2 1 none 1 none Up Up
pw-2:0.* 2 1 none 1 none Up Up
pw-2:1.* 2 1 none 1 none Up Up
pw-3:3 3 1 none 1 none Up Up
pw-4:4.* 4 1 none 1 none Up Up
-------------------------------------------------------------------------------
Number of SAPs : 7
-------------------------------------------------------------------------------
===============================================================================
pw-template
pw-template
Syntax
pw-template [policy-id]
Context
[Tree] (show>service pw-template)
Full Context
show service pw-template
Description
This command displays PW template information.
Platforms
All
Output
The following output is an example of PW template information.
Output Example*A:Dut-B# show service pw-template 1
=======================================================================
PW Template Information
=======================================================================
PW Tmpl Id : 1
Use Provisioned Sdp : enabled VcType : vlan
Acctg Policy : default Collect Stats : disabled
Mac-Learning : enabled Mac-Ageing : enabled
Discard Unkn Src : disabled Limit MacMove : blockable
Mac-Pinning : disabled Vlan VcTag : 4095
MAC Address Limit : no limit Rest Prot Src Mac: disabled
Auto Learn Mac Prot : disabled RestProtSrcMacAct: disable
Block On Peer Fault : disabled
SHG
Name :
Description : (Not Specified)
Rest Prot Src Mac : disabled Rest Unprot Dst : disabled
Auto Learn Mac Prot : disabled RestProtSrcMacAct: disable
Egress
Mac FilterId : none Ip FilterId : none
Ipv6 FilterId : none QoS NetPlcyId : none
Port RedirectQGrp : none Instance Id : none
Ingress
Mac FilterId : none Ip FilterId : none
Ipv6 FilterId : none QoS NetPlcyId : none
Fp RedirectQGrp : none Instance Id : none
IGMP
Fast Leave : disabled Import Plcy : none
Last Memb Intvl : 10 deci-secs Max Nbr Grps : 0
Send Queries : disabled
Version : 3
Force VlanVc Fwd : disabled Control Word : disabled
Hash Label : disabled Hash Lbl Sig Cap : disabled
Last Changed : 02/12/2013 22:11:49
-----------------------------------------------------------------------
Included SDP-Groups
-----------------------------------------------------------------------
red
-----------------------------------------------------------------------
pxc
pxc
Syntax
pxc [pxc-id]
Context
[Tree] (show>port pxc)
Full Context
show port pxc
Description
This command displays PXC port information.
Parameters
- pxc-id
-
Specifies the PXC ID.
Platforms
All
python
python
Syntax
python
Context
[Tree] (clear python)
Full Context
clear python
Description
Commands in this context clear Python commands.
Platforms
All
python
Syntax
python
Context
[Tree] (show python)
Full Context
show python
Description
Commands in this context display Python information.
Platforms
All
python
Syntax
python
Context
[Tree] (tools>dump python)
Full Context
tools dump python
Description
Commands in this context dump Python information.
Platforms
All
python-policy
python-policy
Syntax
python-policy name cache
python-policy name cache hex-key hex-string
python-policy name cache string-key string-key
Context
[Tree] (tools>dump>python python-policy)
Full Context
tools dump python python-policy
Description
This command dumps all cached entries or a specified entry of a specified Python policy.
The DDP key in the output is the python cache persistency record key.
The DDP Key in the output could be used for the tools>dump>persistence>python command.
Parameters
- name
-
Specifies the name of the Python policy, up to 32 characters.
- string-key
-
Specifies the key of the entry to be updated in ASCII strong format, up to 512 characters maximum.
- hex-key
-
Specifies the key of the entry to be updated in hex string format.
Platforms
All
python-policy
Syntax
python-policy name cache hex-key hex-string set-lifetime [lifetime]
python-policy name cache string-key [512 chars max] set-lifetime [lifetime]
Context
[Tree] (tools>perform python-policy)
Full Context
tools perform python-policy
Description
This command set the lifetime of a specified python cache entry.
Parameters
- name
-
Specifies the name of the Python policy, up to 32 characters.
- string-key
-
Specifies the key of the entry to be updated in ASCII strong format.
- hex-string
-
Specifies the key of the entry to be updated in hex string format.
- set-lifetime
-
Specifies the new lifetime of the entry.
Platforms
All
python-policy
Syntax
python-policy
python-policy policy-name [association]|
Context
[Tree] (show>python python-policy)
Full Context
show python python-policy
Description
This command displays information about the currently configured Python policy.
The system will display a list of currently configured Python policy names if no parameter is specified.
Parameters
- policy-name
-
Specifies the Python policy name, up to 32 characters, to display.
- association
-
Displays the associations of the specified Python policy.
Platforms
All
Output
The following output is an example of DHCP Python policy information
Output Exampleshow python python-policy "dhcp"
===============================================================================
Python policy "dhcp"
===============================================================================
Description : (Not Specified)
-------------------------------------------------------------------------------
Messages
-------------------------------------------------------------------------------
Type Dir Script
-------------------------------------------------------------------------------
dhcpDiscover egress dhcpv4
dhcpRequest egress dhcpv4
dhcpAck ingress dtc
-------------------------------------------------------------------------------
No. of Messages: 3
-------------------------------------------------------------------------------
===============================================================================
show python python-policy "dhcp" association
===============================================================================
Python Policy Association
===============================================================================
Location
-------------------------------------------------------------------------------
Service: 500, GrpIf g1, dhcp
-------------------------------------------------------------------------------
No. of Python policy association: 1
===============================================================================
python-policy
Syntax
python-policy name cache all
python-policy name cache hex-key hex-string
python-policy name cache string-key string-key
Context
[Tree] (clear>python python-policy)
Full Context
clear python python-policy
Description
This command clears Python policy data.
Parameters
- name
-
Specifies the name of the Python policy, up to 32 characters.
- string-key
-
Specifies the key of the entry to be updated in ASCII strong format, up to 512 characters maximum.
- hex-string
-
Specifies the key of the entry to be updated in hex string format.
Platforms
All
python-script
python-script
Syntax
python-script
python-script script-name [association | source-in-use]
Context
[Tree] (show>python python-script)
Full Context
show python python-script
Description
This command displays information about the currently configured Python script.
The system will display a list of currently configured Python script names if no parameter is specified.
Parameters
- script-name
-
Specifies the Python script name, up to 32 characters, to display information.
- association
-
Displays the associations of the specified Python script.
- source-in-use
-
Displays the Python source code in use.
Platforms
All
Output
The following output is an example of Python script information.
Output Exampleshow python python-script "dhcpv4"
===============================================================================
Python script "dhcpv4"
===============================================================================
Description : (Not Specified)
Admin state : inService
Oper state : inService
Action on fail: drop
Protection : none
Primary URL : cf1:/dhcpv4.py
Secondary URL : (Not Specified)
Tertiary URL : (Not Specified)
Active URL : primary
Last changed : 01/26/2014 05:02:10
===============================================================================
show python python-script "dhcpv4" association
===============================================================================
Python Script Association
===============================================================================
Policy Type Dir
-------------------------------------------------------------------------------
dhcp dhcpDiscover egress
dhcp dhcpRequest egress
-------------------------------------------------------------------------------
No. of Python script association: 2
===============================================================================
python-script
Syntax
python-script
Context
[Tree] (tools>perform python-script)
Full Context
tools perform python-script
Description
Commands in this context perform Python script operations.
Platforms
All
python-script
Syntax
python-script script-name nat-group nat-group-id statistics
python-script script-name wlan-gw-group wlan-gw-group-id statistics
Context
[Tree] (clear>python python-script)
Full Context
clear python python-script
Description
This command clears Python script statistics.
Parameters
- script-name
-
Specifies the Python script name, up to 32 characters, to display information.
- wlan-gw-group-id
-
Specifies the WLAN-GW group ID.
- nat-group-id
-
Specifies the NAT group ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s
python-script protect
python-script protect
Syntax
python-script protect input file-url hmac-sha256 key secret-key output file-url
Context
[Tree] (tools>perform python-script protect)
Full Context
tools perform python-script protect
Description
This command converts a normal (unprotected) Python script file into an SRPY format with specified key.
Parameters
- input file-url
-
Specifies the URL of the input script file, up to 180 characters.
- key secret-key
-
Specifies the key used to compute the hash, up to 128 characters.
- output file-url
-
Specifies the URL of the output script file, up to 180 characters.
Platforms
All
python-script reload
python-script reload
Syntax
python-script reload name
Context
[Tree] (tools>perform python-script reload)
Full Context
tools perform python-script reload
Description
This command reloads and recompiles the primary, secondary, and tertiary scripts in the specified Python script, in that order. The system uses the first script that comes up.
Executing this command may update the last modified time for the system configuration.
Parameters
- name
-
Specifies the name of the Python script to be reloaded, up to 32 characters.
Platforms
All