Monitor and troubleshoot
Documents under this category provide information about monitoring, diagnosing, and troubleshooting router issues.
- 7450 and 7750 Troubleshooting Guide
- 7950 Troubleshooting Guide
- Log Events Guide
  This guide provides information about log events.
- Log Events Search Tool
  A searchable HTML list of the SR OS events.
- OAM and Diagnostics Guide
  This guide describes how to configure features such as service mirroring and Lawful Intercept (LI), and how to use the Operations, Administration, and Maintenance (OAM) and diagnostics tools.

APS

apsEventChannelMismatch

Table 1. apsEventChannelMismatch properties
Property name	Value
Application name	APS
Event ID	2003
Event name	apsEventChannelMismatch
SNMP notification prefix and OID	APS-MIB.apsNotificationsPrefix.3
Default severity	minor
Source stream	main
Message format string	Channel Mismatch is declared
Cause	Channel Mismatch notification is generated due to mismatch between the transmitted K1 channel (phys port) and the received K2 channel (phys port).
Effect	N/A
Recovery	Configure both local and remote with the same channel type.

apsEventFEPLF

Table 2. apsEventFEPLF properties
Property name	Value
Application name	APS
Event ID	2005
Event name	apsEventFEPLF
SNMP notification prefix and OID	APS-MIB.apsNotificationsPrefix.5
Default severity	minor
Source stream	main
Message format string	FEPL failure is declared
Cause	FEPLF (Far-End Protection Line Failure) notification is generated based on SF (Signal Failure) condition on the protection port in the received K1 Byte.
Effect	Traffic will switch (Tx/Rx) to the working port if the traffic is presently Tx-ed/Rx-ed to/from the protection port.
Recovery	N/A

apsEventModeMismatch

Table 3. apsEventModeMismatch properties
Property name	Value
Application name	APS
Event ID	2002
Event name	apsEventModeMismatch
SNMP notification prefix and OID	APS-MIB.apsNotificationsPrefix.2
Default severity	minor
Source stream	main
Message format string	Mode Mismatch is declared
Cause	Mode Mismatch notification is generated due to a conflict between the current local mode (switching direction or architecture) and the received K2 mode information.
Effect	For switching direction mismatch, the operational switching direction is changed to unidirectional. For switch architecture mismatch, the local end runs in 1+1 mode irrespective of the remote end switching architecture.
Recovery	Configure both local and remote end to run in same switching mode (direction/architecture).

apsEventPSBF

Table 4. apsEventPSBF properties
Property name	Value
Application name	APS
Event ID	2004
Event name	apsEventPSBF
SNMP notification prefix and OID	APS-MIB.apsNotificationsPrefix.4
Default severity	minor
Source stream	main
Message format string	PSB Failure is declared
Cause	A PSBF (Protection Switching Byte Failure) notification is generated due to inconsistent Rx K1 byte or invalid Rx K1 Byte.
Effect	A PSBF condition is considered as signal failure (SF) on the protection port.
Recovery	Correct the K1 byte value.

apsEventSwitchover

Table 5. apsEventSwitchover properties
Property name	Value
Application name	APS
Event ID	2001
Event name	apsEventSwitchover
SNMP notification prefix and OID	APS-MIB.apsNotificationsPrefix.1
Default severity	minor
Source stream	main
Message format string	APS switchover from $subject$.
Cause	APS switchover between working port (channel 1) and protection port (channel 0) can happen due to change of status of any port or user-initiated switch commands on any port.
Effect	Traffic is transmitted to and received from the other channel/port.
Recovery	None.

tApsChannelMismatchClear

Table 6. tApsChannelMismatchClear properties
Property name	Value
Application name	APS
Event ID	2007
Event name	tApsChannelMismatchClear
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.2
Default severity	minor
Source stream	main
Message format string	Channel Mismatch is cleared
Cause	The channel mismatch clear notification is generated when the current status of an APS group gets the channel mismatch condition cleared.
Effect	N/A
Recovery	N/A

tApsChanTxLaisStateChange

Table 7. tApsChanTxLaisStateChange properties
Property name	Value
Application name	APS
Event ID	2015
Event name	tApsChanTxLaisStateChange
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.10
Default severity	warning
Source stream	main
Message format string	APS forced Tx-LAIS state changed to $tApsChanTxLaisState$
Cause	The tApsChanTxLaisStateChange notification is generated when there is a change in the value of tApsChanTxLaisState.
Effect	N/A
Recovery	Investigation is required to determine the cause of the change.

tApsFEPLFClear

Table 8. tApsFEPLFClear properties
Property name	Value
Application name	APS
Event ID	2009
Event name	tApsFEPLFClear
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.4
Default severity	minor
Source stream	main
Message format string	FEPL Failure is cleared
Cause	The FEPLF clear notification is generated when the current status of an APS group gets the FEPLF condition cleared.
Effect	N/A
Recovery	N/A

tApsLocalSwitchCommandClear

Table 9. tApsLocalSwitchCommandClear properties
Property name	Value
Application name	APS
Event ID	2011
Event name	tApsLocalSwitchCommandClear
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.6
Default severity	warning
Source stream	main
Message format string	Local - $apsCommandSwitch$ cleared
Cause	The tApsLocalSwitchCommandClear notification is generated when an APS switch command in the local node gets cleared. Note that a switch command in the local node can be cleared either due to execution of the clear switch command in the local node or due to presence of a higher priority condition in the local or remote node.
Effect	N/A
Recovery	N/A

tApsLocalSwitchCommandSet

Table 10. tApsLocalSwitchCommandSet properties
Property name	Value
Application name	APS
Event ID	2010
Event name	tApsLocalSwitchCommandSet
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.5
Default severity	warning
Source stream	main
Message format string	Local - $apsCommandSwitch$ set
Cause	The tApsLocalSwitchCommandSet is generated when any of the following APS switch commands is executed on an APS channel in the local node. The switch commands are lockoutOfProtection, forcedSwitchWorkToProtect, forcedSwitchProtectToWork, manualSwitchWorkToProtect, and manualSwitchProtectToWork.
Effect	N/A
Recovery	N/A

tApsMcApsCtlLinkStateChange

Table 11. tApsMcApsCtlLinkStateChange properties
Property name	Value
Application name	APS
Event ID	2014
Event name	tApsMcApsCtlLinkStateChange
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.9
Default severity	warning
Source stream	main
Message format string	Control link state changed to $tApsMcApsCtlLinkState$
Cause	The tApsMcApsCtlLinkStateChange notification is generated when there is a change in the value of tApsMcApsCtlLinkState.
Effect	N/A
Recovery	Investigation is required to determine the cause of the change.

tApsModeMismatchClear

Table 12. tApsModeMismatchClear properties
Property name	Value
Application name	APS
Event ID	2006
Event name	tApsModeMismatchClear
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.1
Default severity	minor
Source stream	main
Message format string	Mode Mismatch is cleared
Cause	The Mode mismatch clear notification is generated when the current status of an APS group gets the mode mismatch condition cleared.
Effect	N/A
Recovery	N/A

tApsPrimaryChannelChange

Table 13. tApsPrimaryChannelChange properties
Property name	Value
Application name	APS
Event ID	2016
Event name	tApsPrimaryChannelChange
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.11
Default severity	minor
Source stream	main
Message format string	Switch of the primary APS channel to $apsStatusK1K2Trans$.
Cause	The tApsPrimaryChannelChange notification is generated when there is a switch of the primary APS channel. Object apsStatusK1K2Trans indicates the new primary APS channel.
Effect	N/A
Recovery	Investigation is required to determine the cause of the change.

tApsPSBFClear

Table 14. tApsPSBFClear properties
Property name	Value
Application name	APS
Event ID	2008
Event name	tApsPSBFClear
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.3
Default severity	minor
Source stream	main
Message format string	PSB Failure is cleared
Cause	The PSBF clear notification is generated when the current status of an APS group gets the PSBF condition cleared.
Effect	N/A
Recovery	N/A

tApsRemoteSwitchCommandClear

Table 15. tApsRemoteSwitchCommandClear properties
Property name	Value
Application name	APS
Event ID	2013
Event name	tApsRemoteSwitchCommandClear
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.8
Default severity	warning
Source stream	main
Message format string	Remote - $apsCommandSwitch$ cleared
Cause	The tApsRemoteSwitchCommandClear is generated when the received K1 byte (APS-MIB::apsStatusK1K2Rcv) from a peer indicates that an APS switch command just got cleared on an APS channel in the remote (peer) node.
Effect	N/A
Recovery	N/A

tApsRemoteSwitchCommandSet

Table 16. tApsRemoteSwitchCommandSet properties
Property name	Value
Application name	APS
Event ID	2012
Event name	tApsRemoteSwitchCommandSet
SNMP notification prefix and OID	TIMETRA-APS-MIB.tApsNotifications.7
Default severity	warning
Source stream	main
Message format string	Remote - $apsCommandSwitch$ set
Cause	The tApsRemoteSwitchCommandSet is generated when the received K1 byte (APS-MIB::apsStatusK1K2Rcv) from a peer indicates that an APS switch command just got executed on an APS channel in the remote (peer) node.
Effect	N/A
Recovery	Investigation is required to determine the cause of the change.

March 15, 2024