Configuration Commands

sFlow System Commands

sflow

Syntax

sflow

Context

config>sflow

Description

This command enables context to configured sflow agent parameters.

egress-counter-map

Syntax

egress-counter-map policer policer-id traffic-type {unicast | multicast | broadcast} [create]

egress-counter-map queue queue-id traffic-type {unicast | multicast | broadcast} [create]

no egress-counter-map policer policer-id

no egress-counter-map queue queue-id

Context

config>sflow

Description

This command configures the egress counter map for sFlow. The map must be configured so sFlow agent understands how to interpret data collected against SAP queues and policers. Multiple queues and policers can be mapped to the same traffic-type using separate line entries.

The no form of this command deletes a SAP policy queue/policer from the map.

Default

No mapping is created by default.

Parameters

policer-id

Specifies the policer ID in a SAP egress QoS policy. If the SAP policy does not have a policer with the specified ID, the map entry will be ignored for this SAP.

Values

1 — 8

queue-id

Specifies the queue ID in a SAP egress QoS policy. If the SAP policy does not have a queue with the specified ID, the map entry will be ignored for this SAP.

Values

1 — 8

ingress-counter-map

Syntax

ingress-counter-map policer policer-id traffic-type {unicast | multicast | broadcast} [create]

ingress-counter-map queue queue-id traffic-type {unicast | multicast | broadcast} [create]

no ingress-counter-map policer policer-id

no ingress-counter-map queue queue-id

Context

config>sflow

Description

This command configures the ingress counter map for sFlow. The map must be configured so sFlow agent understands how to interpret data collected against SAP queues and policers. Multiple queues/policers can be mapped to the same traffic-type using separate line entries.

The no form of this command deletes a SAP policy queue/policer from the map.

Default

No mapping is created by default.

Parameters

policer-id

Specifies the policer ID in a SAP ingress QoS policy. If the SAP policy does not have a policer with the specified ID, the map entry will be ignored for this SAP.

Values

1 — 32

queue-id

Specifies the queue ID in a SAP ingress QoS policy. If the SAP policy does not have a queue with the specified ID, the map entry will be ignored for this SAP.

Values

1 — 32

receiver

Syntax

receiver receiver-name [create]

no receiver

Context

config>sflow

Description

This command creates an sFlow receiver context or enters existing sFlow receiver context for the sFlow agent.

The no form of this command deletes an existing sFlow receiver context.

Default

No receivers are created by default.

Parameters

receiver-names

String of up to 127 characters.

ip-addr-primary

Syntax

ip-addr-primary ip-address[:port]

no ip-addr-primary

Context

config>sflow>receiver

Description

This command configures primary IPv4 or IPv6 destination address for the sFlow agent to send sFlow datagrams to. Optionally a destination port can also be configured (by default port 6343 is used).

The no form of this command deletes primary sFlow receiver destination.

Default

no ip-addr-primary

Parameters

ip-address

Specifies the IPv4 or IPv6 address to send the sFlow datagrams to.

Values

a.b.c.d (IPv4) x:x:x:x:x:x:x:x (IPv6) [x:x:x:x:x:x:x:x] (IPv6) x - [0..FFFF]H

port

Specifies the UDP destination port to send the sFlow datagrams to.

Values

1 — 65535

ip-addr-backup

Syntax

ip-addr-backup ip-address[:port]

no ip-addr-backup

Context

config>sflow>receiver

Description

This command configures back-up IPv4 or IPv6 destination address for the sFlow agent to send sFlow datagrams to. Optionally a destination port can also be configured (by default port 6343 is used).

The no form of this command deletes backup sFlow receiver destination.

Default

no ip-addr-backup

Parameters

ip-address

Specifies the IPv4 or IPv6 address to send the sFlow datagrams to.

Values

a.b.c.d (IPv4) x:x:x:x:x:x:x:x (IPv6) [x:x:x:x:x:x:x:x] (IPv6) x - [0..FFFF]H

port

Specifies the UDP destination port to send the sFlow datagrams to.

Values

1 — 65535

max-data-size

Syntax

max-data-size bytes

Context

config>sflow>receiver

Description

This configures maximum data size for sFlow UDP datagrams sent to the collector.

To restore default configuration, execute max-data-size 1400.

Default

1400 bytes

Parameters

bytes

An integer

Values

200— 1500