| Add, modify, or delete a call server | |||
|
| GO | |
|
This topic describes the steps to add, modify, or delete a call server from the Lucent CM system. Call servers provide calling features to end users.
Lucent CM supports the following call servers:
Lucent Feature Server 5000 (FS 5000)
Lucent Feature Server 3000 (FS 3000)
The different call servers can provide different sets of call features.
General call server parameters:
|
Parameter |
Description |
|
Call Server ID |
Identifier of the call server. For use by the Lucent CM system only. |
|
Call Server Type |
The type of call server that provides call services. |
|
Enable |
Checkmark box to enable the call server. |
|
Quarantined 1 |
Checkmark box to quarantine the FS 5000 call server. By quarantining the server, you prevent the Lucent CM system from using the server while the server is recovering from a disaster. |
|
Account Name |
System administrator account name for login through the call server connection for configuration. |
|
Password |
Password for the system administrator account. |
|
Verify Password | |
|
Status |
The status of the Lucent CM connection to the call server. |
|
Details |
Button to display call server connection details. |
| 1 |
Parameters showing the FS 5000 call server connection status:
|
Parameter |
Description |
|
Node |
Node name. The node name is the FQDN for the interface. |
|
Status |
The status of the DB and each WPIF interfaces between the call server and the Lucent CM system. |
The FS 5000 parameters display when you select FS 5000 as Call Server Type.
FS 5000 parameters:
|
Parameter |
Description |
|
Host Name |
Host name of the FS 5000 call server. |
|
Host Port |
Host port of the FS 5000 call server. |
|
PSI Protection Call Server ID |
Identifier of the FS 5000 call server that acts as protection call server for PSI-based services. |
The OMC-P parameters display when you select FS 5000 as Call Server Type.
OMC-P parameters:
|
Parameter |
Description |
|
Host Name |
Host name of the OMC-P that manages the FS 5000. |
|
Host Port |
Host port of the SOAP interface on OMC-P that manages the FS 5000. |
|
Account |
System administrator account name for the OMC-P. |
|
Enable |
Checkmark box to enable management of the Lucent CM by OMC-P. |
|
Password |
Password for the OMC-P administrator account. |
|
Verify Password | |
|
Status |
The status of the connection between the Lucent CM server and the OMC-P Server. |
|
Details |
Button to display OMC-P Server connection details. |
|
Lucent CM System Name |
Name of the Lucent CM system in OMC-P. |
|
Call Server Switch Name |
Name of the FS 5000 call server in OMC-P. |
|
Call Server Subscriber DB Name |
Name of the FS 5000 subscriber database in OMC-P. |
Parameters showing the FS 3000 call server connection status:
|
Parameter |
Description |
|
Node |
Node name |
|
OCI-C Status or CAP Status 1 |
The status of the call control interface between the call server and the Lucent CM system. |
|
OCI-P Status or OSS Status 1 |
The status of the provisioning interface between the call server and the Lucent CM system. |
| 1 | If the type of protocol the FS 3000 uses is not known, the column headers are labelled Call Status and Provision Status. |
Important! Until the provisioning interface is CONNECTED, no call logging or Click-To-Dial services are available to end users, and no feature settings can be changed. Also if you enable Autoprovision, no user accounts can be added, modified or deleted.
If the connection to the call server is enabled and the call control interface and provisioning interface is NOT CONNECTED, a problem exists.
The FS 3000 parameters display when you select FS 3000 as Call Server Type.
FS 3000 call server parameters:
|
Parameter |
Description |
|
Primary Call Server |
Host name of the FS 3000 primary application server. |
|
Secondary Call Server |
Host name of the FS 3000 secondary application server. |
|
System Phone Domain |
Domain name for the telephone system. This parameter is the domain that is provisioned for the FS 3000 when it is installed. The domain name can be found in the FS 3000 administration GUI at the system level. Select Resources → Domains. When the domain is incorrect, users cannot be added. System Phone Domain must match provisioning in the FS 3000. |
|
Auto Provision |
Checkmark box to enable automatic user provisioning to the call server. Refer to Auto provisioning on Lucent FS 3000 |
|
Sign on URL |
The URL used to log in to the FS 3000 users web interface. |
|
Time Zone |
The time zone where the call server is located. |
If automatic user provisioning is enabled, the changes that are made using the Lucent CM Explorer are forwarded to the Lucent FS 3000 call server. If automatic user provisioning is disabled, the changes that are made, are not forwarded to the Lucent FS 3000. Changes must be made manually on the Lucent FS 3000 to ensure that configuration data remains synchronized between the Lucent FS 3000 and the Lucent CM.
When auto-provisioning is enabled and no provisioning connection to the Lucent FS 3000 is available, users cannot be deleted. First disable auto-provisioning if you want to delete users when no provisioning connection is available.
Before you delete a call server, you must delete all packages.
Perform the following steps:
1 |
At the Lucent CM Explorer tree view, navigate to the Call server folder (Lucent CM System → Services → Call Server). Result: The Call Server List displays, listing the available call servers. | ||||||||
2 |
| ||||||||
3 |
Configure the general call server parameters and the parameters for the call server type you selected. Important! For the call server to be able to provide services, it must be enabled. Check the Enabled checkmark box to enable the call server. | ||||||||
4 |
Click Add to add the call server. | ||||||||
5 |
Add, modify, or delete the packages that are associated with the call server: | ||||||||
6 |
Click Update to save the call server. Result: The list is updated to reflect the changes. End of steps |
|
|
GO | |
|
| © Lucent Technologies | |||