Segment routing with IPv6 data plane (SRv6)

This section describes configuration of the SRv6 locator.

An SRv6 SID is a 128-bit IPv6 address which follows the structure defined by RFC 8986:

SRv6 SID={LOCATOR:FUNCTION:ARGUMENT}.

The user must configure the main SRv6 subnet for this node. This is the locator and is, essentially, an IPv6 subnet (prefix and length) that provides reachability (longest prefix match) to all the SIDs originated by this node. The prefix is encoded in the LOCATOR field of the SRv6 SID and can have a length of either 64 or 96 bits.

The locator is further subdivided into a SID block and a node ID. For example, locator 3FFE:0:0:A1::/64 has a SID block of 3FFE:0 and node ID of 0:A1.

All nodes participating in an SRv6 domain must draw their locator and SIDs from the same SID block. In the previous example, the SID block is subnet 3FFE:0::/32.

Use the following commands to configure the SRv6 locator.

• MD-CLI

  *[pr:/configure router "Base" segment-routing segment-routing-v6 locator "test"]
  A:admin@test# tree detail
  +-- admin-state <keyword>
  +-- algorithm <number>
  +-- apply-groups <reference>
  +-- apply-groups-exclude <reference>
  +-- block-length <number>
  +-- function-length <number>
  +-- label-block <reference>
  +-- prefix
  |   +-- ip-prefix <global-unicast-ipv6-address-and-prefix>
  +-- static-function
  |   +-- label-block <reference>
  |   +-- max-entries <number>
  +-- termination-fpe <reference>
  +-- origination-fpe <reference>
  +-- source-address <global-unicast-ipv6-address>
  
  

• classic CLI

  configure+--router
     +--segment-routing
        +--segment-routing-v6
           +--origination-fpe* <fpe>
           +--source-address <ipv6-address>
           +--locator* <locator-name>
              +--admin-state (enable|disable)
              +--termination-fpe <fpe>
              +--algorithm <0, 128-255>
              +--prefix
                 +--ip-prefix <ipv6-address/prefix-length>
              +--block-length <0-96>
              +--function-length <16 | 20-96>
              +--label-block <block-name>
              +--static-function
                        +--max-entries <integer>
                        +--label-block <block-name> 
  

The two reserved label ranges (locator>label-block and locator>static-function>label-block) are mutually exclusive.

If locator>static-function>label-block is configured, then the labels associated with the service functions are drawn as follows:

• from the label block for static service function

• from the dynamic label range for dynamic service functions

If locator>label-block is configured, labels associated with service functions are drawn from the label block for both static and dynamic service functions.

Configuring a function length of 16 requires the use of locator>label-block. Function lengths of 16 are not supported on locator>static-function>label-block.

One locator is required for algorithm 0 and one for each IGP flexible algorithm (128-255). The same locator can be shared by multiple IGP instances for the same algorithm number.

The locator prefix,(in this example, 3FFE:0:0:A1::/64), is advertised in the SRv6 Locator TLV in IS-IS in both algorithm 0 and any configured flexible algorithm number, as defined in draft-ietf-lsr-isis-srv6-extensions. It is also advertised as a prefix in IP Reachability TLV (IS-IS TLV 236) in algorithm 0, so the routers that do not support SRv6 can still route the packet to the next hop of the locator and, eventually, to its destination node.

The FUNCTION field is user-configurable. The ARGUMENT field is set to all zeros and is not configurable. The ARGUMENT length must be signaled as zero in the IS-IS End and End.X SIDs and in the BGP service SIDs. Also, the sum of the LOCATOR and FUNCTION lengths must be less than or equal to 128.

Within algorithm 0 and each IGP flexible algorithm, the locator function (FUNCTION field) assigns the values of the End SID and End.X SID which correspond to the node SID and the adjacency or adjacency SET SID, respectively.

The locator function also assigns the value of the service SIDs owned by this node and advertised in the BGP control plane (End.DT4, End.DT6, End.DT46, and End.DX2).

The FUNCTION field can be subdivided into a static and a dynamic subrange. The user can draw from the static subrange to manually assign an SRv6 SID to a node, a local adjacency, or a service. IS-IS and BGP can draw from the dynamic subrange to assign a SID to a local adjacency or a service. The SID of an adjacency to an IS-IS neighbor, over a broadcast interface (LAN End.X), is always dynamically assigned and is not configurable.

The following CLI commands enable the allocation of an SRv6 SID function value. Manual allocation of a static function value is supported for nodes (End SIDs), adjacencies over a P2P interface (End.X SIDs), and service SIDs. Auto-allocation is supported for adjacencies over a P2P interface (End.X SIDs) and service SIDs.

• MD-CLI

  [pr:/configure router "Base" segment-routing segment-routing-v6]
  A:admin@test# tree detail
  +-- base-routing-instance
  |   +-- apply-groups <reference>
  |   +-- apply-groups-exclude <reference>
  |   +-- locator <reference>
  |       +-- function
  |           +-- end <number>
  |           |   +-- srh-mode <keyword>
  |           +-- end-x-auto-allocate <keyword> protection <keyword>
  |           +-- end-x <number>
  |           |   +-- interface-name <reference>
  |           |   +-- protection <keyword>
  |           |   +-- srh-mode <keyword>
  |           +-- end-dt4
  |           +-- end-dt46
  |           +-- end-dt6
  
  

• classic CLI

  configure
  +--router
  +---segment-routing
  |   +---segment-routing-v6
  |   |   +--- base-routing-instance
  |   |   |   |   locator <locator-name>
  |   |   |   |   +---function
  |   |   |   |   |   |   end <integer>
  |   |   |   |   |   |   +---srh-mode <psp | usp>   
  |   |   |   |   |   +---end-x-auto-allocate <psp|usp> <protected|unprotected>
  |   |   |   |   |   +---end-x <integer>
  |   |   |   |   |   |   +---interface <name>
  |   |   |   |   |   |   +---srh-mode <psp | usp>   
  |   |   |   |   |   |   +---protection <protected|unprotected>
  |   |   |   |   |   +---end-dt4 [<integer>]
  |   |   |   |   |   +---end-dt6 [<integer>]
  |   |   |   |   |   +---end-dt46 [<integer>]

configure router isis segment-routing-v6 micro-segment-locator

The following table lists the TLVs that micro-segment SRv6 supports in addition to the TLVs described in SRv6 IS-IS TLVs.

The following table lists the endpoint behavior codepoint for each SID function encoded in a micro-segment SRv6 SID.

This feature extends the support of SRv6 to multitopology IPv6 (MT2) in IS-IS.

The BGP service control plane required extensions are specified in RFC 9252, BGP Overlay Services Based on Segment Routing over IPv6 (SRv6). BGP requires some changes in the IPv6, VPN-IPv4, VPN-IPv6, and EVPN family routes so that the egress PE can signal the following End programming behaviors to the ingress PE:

• Layer 2 SRv6 service SIDs

  End.DX2

  Layer 2 decapsulation and cross-connect to an Epipe egress SAP, signaled by AD per-EVI routes

• Layer 3 SRv6 service SIDs

  End.DT4

  a VPRN (or GRT) route-table lookup, signaled by VPN-IPv4 or EVPN in Interface-less (EVPN-IFL) IPv4 prefix routes (also by IPv4)

  End.DT6

  a VPRN (or GRT) route-table IPv6 lookup, signaled by VPN-IPv6 or EVPN-IFL IPv6 prefix routes (also by IPv6)

  End.DT46

  a VPRN route-table lookup for IPv4 or IPv6 prefixes, signaled by VPN-IPv4 or VPN-IPv6 or EVPN-IFL IPv4 or IPv6 prefix routes

The following figure shows an example for the End.DX2 behavior for EVPN-VPWS services.

The ingress and egress PEs behave as follows:

• The egress PE (PE6) advertises an A-D per EVI route with the SRv6 Service SID that identifies the End.DX2 behavior. The service SID includes the configured locator in the Epipe (A6::), as well as the allocated function (E9), which identifies the Epipe at the egress PE.

• The ingress PE (PE1) imports the A-D per EVI route and creates an EVPN destination in the corresponding Epipe to A6::E9.

• When PE1 receives frames at the access SAP, it encapsulates the frames into an SRv6 packet using the configured IP SA. The IP DA is the EVPN destination SID.

• Shortest path forwarding is considered in the example shown in End.DX2 behavior for EVPN-VPWS, and therefore the EVPN destination SID is encoded in the IP DA. If TI-LFA is required, PE1 modifies the encapsulation to include an SRH and additional SIDs.

• When the SRv6 packet arrives at PE6, the SID encoded in the IP DA identifies the packet for termination on PE6 and the Epipe for decapsulation and forwarding.

Similar procedures are followed for the other required services.

The following table lists the functions that micro-segment SRv6 implements to support the requirements.

The following BGP extensions are supported, as per RFC 9252:

• SRv6 Service TLV:

  • SRv6 Service TLV encoded in the BGP Prefix-SID attribute

  • SRv6 SID Information Sub-TLV (SRv6 Service Sub-TLV type 1) encoded in the SRv6 Service TLV

  • SRv6 SID Structure Sub-Sub-TLV (SRv6 Service Data Sub-Sub-TLV type 1)

• Transposition of 16 or 20 bits of the FUNCTION to the Label field of the NLRI

• Arg.FE2 arguments used for split-horizon filtering in EVPN multihoming, advertised in the EVPN AD per-ES routes with 16 bits of the argument transposed to the label field of the ESI Label extended community.

The BGP extensions are applied to the following routes by setting the behavior field in the SRv6 Services TLV, as per RFC 8986:

• VPN-IPv4

• VPN-IPv6

• IPv4

• IPv6

• EVPN AD per-EVI

• EVPN AD per-ES

• EVPN MAC/IP

• EVPN Inclusive Multicast Ethernet Tag

The EVPN, VPN-IPv4, VPN-IPv6, IPv4, and IPv6 routes for the SRv6-enabled services are advertised along with the SRv6 Service TLV. The TLV format is described in RFC 9252 and shown in the following figure.

The SRv6 Service TLV encoded in the BGP Prefix-SID attribute can have two different types:

• Type 5 is used for Layer 3 service SIDs or the SIDs signaled for VPRN services with VPN-IP or EVPN-IFL routes. Layer 3 service SIDs are also supported for the base router along with IPv4 or IPv6 routes.

• Type 6 is used for Layer 2 service SIDs or the SIDs signaled for Epipe or VPLS services. Type 6 is supported along with AD per-EVI and per-ES routes for Epipes.

The SRv6 Service TLV may contain an unordered list of sub-TLVs, but currently the SRv6 Service TLV is advertised with only one sub-TLV: the SRv6 SID Info sub-TLV (type 1). This sub-TLV encodes the following information:

• For the SID value, the entire 128-bit SID is allocated to the service, including the locator configured for the service and the allocated FUNCTION (which can be dynamically allocated or statically configured on the service). The ARGUMENT is always 0.

• SID flags are all zero.

• Endpoint behavior encodes the behavior as in RFC 8986, in decimal values. The following values are relevant for SR OS:

  • 18 – End.DT6

  • 19 – End.DT4

  • 20 – End.DT46

  • 21 – End.DX2

  • 24 – End.DT2m (only for AD per-ES routes)

• One SID Structure Sub-Sub-TLV (Service Data Sub-Sub-TLV type 1)

The SID Structure Sub-Sub-TLV is always included in routes with label fields and always uses the following values when advertised:

• Locator Block Length - encodes the length of the block configured in the locator for the service

• Locator Node Length - the length of the node configured in the locator for the service

• Function Length - configurable in the range 20 to 96

• Argument Length - 0 (default) or 16 (configured)

• Transposition Length (TL) - 20 for EVPN and VPN-IP routes with full SIDs and 16 for micro segments and 0 for IP routes in the base router

• Transposition Offset (TO)

  • for EVPN and VPN-IP routes:

    • If the Function Length equals 20 or 16, the Transposition Offset (TO) value equals the prefix length configured in the locator

    • If the Function Length is greater than 20, the TO value equals:

      (prefix length configured in the locator) + (FunctLength 20)

  • for IP routes in base router, TO value is always 0

• For IP routes in the base router, the TO value is always 0.

The purpose of the SID Structure Sub-Sub-TLV is twofold:

• Advertise the structure of the SRv6 SID used in the service, including the length of the Locator block, node, function and argument.

• Support transposition procedures for efficient service route packing. The FUNCTION is transposed into the label field in the route’s NLRI. Because the rest of the SID is common for routes of the same type in the service, this transposition operation supports efficient packing of routes into the same BGP update.

The following figure shows how the FUNCTION part of the SID is transposed. This example illustrates how transposition works for EVPN-VPWS, and it would be similar for VPN-IP routes.

In the preceding figure, PE6 is configured with an Epipe that uses a configured locator with LB length = 40 bits and LN length = 24 bits. The Function length is set at 24, and 20 bits are always transposed into the NLRI (non-configurable). In the preceding figure, the following rules apply:

• On reception, the router can build any SID out of the received route, irrespective of transposition, as long as the lengths are correctly encoded.

• On transmission, the system performs a transposition for VPN-IP and EVPN service routes as follows:

• • If Function Length is greater than 20 in the Locator configuration, the function bits are put at the right-most bits of the L bits. For example, if LB LEN is 40 bits and the LN Len is 24 bits:

  • If Function Length = 20, the entire function is transposed into the label field, and the following is signaled in the route:

    Length [LBL, LNL, FL, AL] : [40, 24, 20, 0]

    TL:20, TO:64

    *A:PE-4>config>router>segment-routing>srv6>locator# info 
    ----------------------------------------------
                            shutdown
                            block-length 40
                            termination-fpe 1
                            prefix
                                ip-prefix cafe:1:0:4::/64
                            exit
                            static-function
                                max-entries 10
                            exit
    ----------------------------------------------
    *A:PE-4>config>router>segment-routing>srv6>locator# no shutdown 
    
    3 2021/01/19 08:21:16.827 UTC MINOR: DEBUG #2001 Base Peer 1: 2001:db8::3
    "Peer 1: 2001:db8::3: UPDATE
    Peer 1: 2001:db8::3 - Send BGP UPDATE:
        Withdrawn Length = 0
        Total Path Attr Length = 102
        Flag: 0x90 Type: 14 Len: 33 Multiprotocol Reachable NLRI:
            Address Family VPN_IPV4
            NextHop len 12 NextHop 192.0.2.4
            10.0.0.3/32 RD 192.0.2.4:20 Label 524254
        Flag: 0x40 Type: 1 Len: 1 Origin: 0
        Flag: 0x40 Type: 2 Len: 0 AS Path:
        Flag: 0x40 Type: 5 Len: 4 Local Preference: 100
        Flag: 0xc0 Type: 16 Len: 8 Extended Community:
            target:64500:20
        Flag: 0xc0 Type: 40 Len: 37 Prefix-SID-attr:
           SRv6 Services TLV (37 bytes):-
             Type: SRV6 L3 Service TLV (5)
             Length: 34 bytes, Reserved: 0x0
             SRv6 Service Information
             Service Information sub-TLV Type 1
                Type: 1 Len: 30 Rsvd1: 0x0
                SRv6 SID: cafe:1:0:4::
                SID Flags: 0x0 Endpoint Behavior: 0x14 Rsvd2: 0x0
                SRv6 SID Sub-Sub-TLV
                   Type: 1 Len: 6
                   BL:40 NL:24 FL:20 AL0 TL:20 TO:64
    

  • If Function Length = 32, part of the function is transposed into the label field, and the following is signaled in the route:

    Length [LBL, LNL, FL, AL] : [40, 24, 20, 0]

    TL:20, TO:76

    *A:PE-4>config>router>segment-routing>srv6>locator# function-length 32 
    *A:PE-4>config>router>segment-routing>srv6>locator# info 
    ----------------------------------------------
                            shutdown
                            block-length 40
                            function-length 32
                            termination-fpe 1
                            prefix
                                ip-prefix cafe:1:0:4::/64
                            exit
                            static-function
                                max-entries 10
                            exit
    ----------------------------------------------
    *A:PE-4>config>router>segment-routing>srv6>locator# no shutdown 
    
    8 2021/01/19 08:27:09.318 UTC MINOR: DEBUG #2001 Base Peer 1: 2001:db8::3
    "Peer 1: 2001:db8::3: UPDATE
    Peer 1: 2001:db8::3 - Send BGP UPDATE:
        Withdrawn Length = 0
        Total Path Attr Length = 102
        Flag: 0x90 Type: 14 Len: 33 Multiprotocol Reachable NLRI:
            Address Family VPN_IPV4
            NextHop len 12 NextHop 192.0.2.4
            10.0.0.3/32 RD 192.0.2.4:20 Label 524254
        Flag: 0x40 Type: 1 Len: 1 Origin: 0
        Flag: 0x40 Type: 2 Len: 0 AS Path:
        Flag: 0x40 Type: 5 Len: 4 Local Preference: 100
        Flag: 0xc0 Type: 16 Len: 8 Extended Community:
            target:64500:20
        Flag: 0xc0 Type: 40 Len: 37 Prefix-SID-attr:
           SRv6 Services TLV (37 bytes):-
             Type: SRV6 L3 Service TLV (5)
             Length: 34 bytes, Reserved: 0x0
             SRv6 Service Information
             Service Information sub-TLV Type 1
                Type: 1 Len: 30 Rsvd1: 0x0
                SRv6 SID: cafe:1:0:4::
                SID Flags: 0x0 Endpoint Behavior: 0x14 Rsvd2: 0x0
                SRv6 SID Sub-Sub-TLV
                   Type: 1 Len: 6
                   BL:40 NL:24 FL:32 AL0 TL:20 TO:76
    

• The label field of the NLRI (VPN-IP and EVPN routes) encodes the FUNCTION that is dynamically or statically allocated for the service.

With the transposition procedure, multiple NLRIs with the same common SRv6 SID (minus the function) can be packed into the same BGP update, as is done for regular VPN-IP or EVPN route for MPLS tunnels. The packing benefit is illustrated in the following figure.

The service routes that are supported for SRv6 are:

• VPRN services, configured for SRv6:

  • VPN-IPv4 routes

  • VPN-IPv6 routes

• Base router

  • IPv6 routes, if configured for SRv6 in IPv6 family

  • IPv4 routes, if configured for SRv6 in IPv4 family

• Epipe services, configured for SRv6:

  • EVPN AD per-EVI routes

  • EVPN AD per-ES routes, for Epipes that make use of Ethernet Segments

• VPLS services configured for SRv6:
  • EVPN AD per-EVI routes
  • EVPN AD per-ES routes, including the advertisement of arguments
  • EVPN MAC/IP Advertisement routes
  • EVPN Inclusive Multicast Ethernet Tag routes

As specified in RFC 9252, BGP Overlay Services Based on Segment Routing over IPv6 (SRv6), the egress PE may set the next hop to any of its IPv6 addresses. When the IPv6 address value is not covered by the SRv6 locator from which the SRv6 Service SID is allocated, the ingress PE performs reachability checks for the SRv6 Service SID in addition to the BGP next-hop reachability procedures.

Next hop and locator resolution considerations include the following:

• On reception of a BGP SRv6 service route, both the locator and the next hop are resolved independently in the route table.
• For base instance routes (not service routes), the following command triggers the independent resolution of the next hop and the locator reachability (and collates their states that drive route programming):
  • MD-CLI

    configure router bgp segment-routing-v6 family ignore-received-srv6-tlvs false

  • classic CLI

    configure router bgp segment-routing-v6 family no ignore-received-srv6-tlvs

  The locator state is considered only if the preceding command is configured.

• Whether the router does next-hop-self or next-hop-unchanged, there is no affect on the RIB-IN processing and reachability because the next-hop behavior is a RIB-OUT parameter.
• If a received route has a resolved next hop but unresolved locator, the show router bgp routes command shows "valid/best" but not "used" in the route flags. The following command displays the locator and the resolution of the locator.

  show router bgp next-hop 192.0.2.3 detail vpn-ipv4

===============================================================================
 BGP Router ID:192.0.2.4        AS:64500       Local AS:64500      
===============================================================================

===============================================================================
BGP VPN Next Hop
===============================================================================
-------------------------------------------------------------------------------
VPN Next Hop          : 192.0.2.3
Autobind              : gre 
Labels                : --
Admin-tag-policy      : --
Strict-tunnel-tagging : N
Color                 : --
Locator               : cafe:1:0:3::/64
-------------------------------------------------------------------------------
Resolving Prefix : 192.0.2.3/32
Preference       : 18                   Metric           : 10
Reference Count  : 6                    Owner            : GRE
Fib Programmed   : Y                    
Resolved Next Hop: 192.168.34.1
Egress Label     : n/a                  TunnelId         : 4294967293
Locator State    : Resolved             
-------------------------------------------------------------------------------
Next Hops : 1
===============================================================================

configure router bgp segment-routing-v6 family upa-trigger next-hop frr

configure service vprn bgp-ipvpn segment-routing-v6 upa-trigger next-hop frr

Route matching criteria and route modifying actions that are specific to BGP routes carrying SRv6 TLVs can be configured for route policies.

SR OS supports the following route matching criteria:

• SRv6 TLV presence as match criterion

  Use the following command in the from clause of a policy-statement entry to configure whether a BGP route with associated SRv6 TLVs matches the entry:

  Note: Named entries are only supported in the MD-CLI.

  • MD-CLI

    configure policy-options policy-statement entry from srv6-tlv
    configure policy-options policy-statement named-entry from srv6-tlv

  • classic CLI

    configure router policy-options policy-statement entry from srv6-tlv

  This match criterion is supported in BGP import policies, BGP export policies, and VRF or VSI import policies.

• SRv6 SID prefix as match criterion

  Use the following command in the from clause of a policy-statement entry to configure a SID or micro-segment (uSID) value in the SRv6 TLV (including the locator and function) to be used as match criterion for a BGP route:

  • MD-CLI

    configure policy-options policy-statement entry from srv6-sid-prefix
    configure policy-options policy-statement named-entry from srv6-sid-prefix

  • classic CLI

    configure router policy-options policy-statement entry from srv6-sid-prefix

  This match criterion uses longest prefix match logic and is supported in BGP import policies, BGP export policies, and VRF or VSI import policies.

SR OS supports the following route modifying actions:

• SRv6 locator modification

  Use the following command in the action clause of a policy-statement entry to modify the SRv6 TLV in a BGP route to use a different locator than the default or the locator added using the command options in the configure router bgp segment-routing-v6 family add-srv6-tlvs context:

  • MD-CLI

    configure policy-options policy-statement entry action srv6-locator
    configure policy-options policy-statement named-entry action srv6-locator

  • classic CLI

    configure router policy-options policy-statement entry action srv6-locator

  This route modifying action is supported in BGP export policies and SRv6-specific VRF export policies.

• SRv6 uSID locator modification

  Use the following command in the action clause of a policy-statement entry to modify the SRv6 TLV in a BGP route to use a different uSID locator than the default or the uSID locator added using the command options in the configure router bgp segment-routing-v6 family add-srv6-tlvs context:

  • MD-CLI

    configure policy-options policy-statement entry action srv6-micro-segment-locator
    configure policy-options policy-statement named-entry action srv6-micro-segment-locator

  • classic CLI

    configure router policy-options policy-statement entry action srv6-micro-segment-locator

  This route modifying action is supported in BGP export policies and SRv6-specific VRF export policies.

SRv6 locator and SID resolution is performed in the RTM and forwarding of all SRv6 packets is performed in the FIB.

The TTM is used to save details of the SRv6 tunnel but is not used directly to forward user or CPM originated packets.

The RTM and FIB are programmed with the routes of the local and remote locators, the local End.X SIDs, and the local End SIDs.

When a policy is applied to export SRv6 routes from the route table to another IS-IS instance, only the IP Reachability TLV and the locator TLV, along with the End SID sub-TLVs, are advertised by the receiving IS-IS instance. Local End, End.X, and LAN End.X routes are not exported nor advertised as separate routes.

• remote locator (route owner = SRv6 IS-IS)

  All routers in the SRv6 domain populate a resolved remote locator prefix received in the SRv6 Locator TLV in the route table and the FIB.

  A SRv6 packet is always forwarded out in the datapath using the FIB.

  For algorithm 0, the same prefix is advertised with the IP reach prefix TLV and the SRv6 Locator TLV. A single route entry is programmed in the route table and the FIB.

  The prefix of an IGP flexible algorithm locator TLV is never advertised with an IP reach prefix TLV. Therefore, the route of the locator TLV is programmed in the route table and the FIB.

  • remote locator with up to 64 ECMP next hops

    IS-IS models a remote locator prefix with two or more ECMP next hops as an IGP route with tunneled next hops using a protected NHLFE with hardware PG-ID per tunneled next hop.

    This implementation provides uniform failover in ECMP. IS-IS allocates a hardware PG-ID to each next hop it establishes an adjacency with. That PG-ID is then used when programming SRv6 routes of a remote locator and of a local adjacency that resolve to this next hop.

    The route table manager programs the route into the FIB. IS-IS creates an SRv6 tunnel for the locator prefix. The tunnel is added to the tunnel table. The IS-IS route entries in the route table and the FIB point to the tunnel ID of this tunnel in the tunnel table.

    Weighted ECMP, when enabled on the interfaces of this IS-IS instance, is supported when forwarding packets over the locator next hops.

  • remote locator with primary or backup next hops

    To provide uniform failover, IS-IS models a remote locator prefix with a primary next hop or a primary and LFA backup next-hop pair as an IGP route with a tunneled next hop using a protected NHLFE with a hardware PG-ID.

    The route table manager programs the route into the FIB. IS-IS creates a SRv6 tunnel for the locator prefix. The tunnel is added to the tunnel table. The IS-IS route entries in the route table and the FIB point to the tunnel ID of this tunnel in tunnel table.

• local locator (route owner = SRv6)

  All routers in the SRv6 domain populate a route entry in the route table and the FIB to terminate packets destined for the local locator. This is modeled like any other local route but with the SRv6-specific route owner.

• local adjacency SID (route owner = IS-IS)

  All routers in the SRv6 domain populate a route entry in the route table and FIB for each local End.X and LAN End.X adjacency SID with primary and backup next hops.

  The route table, and FIB entries are modeled like a remote locator prefix with primary and backup next hops.

• local End SID (route owner = SRv6)

  All routers in the SRv6 domain populate a route entry in the route table and the FIB to terminate packets destined for each local End SID. This is modeled like any other local route but with the SRv6-specific route owner.

With micro-segment SRv6, entries pertaining to local services populate the RTM and FIB. In the FIB, those entries are aggregated. At most, 15 entries are needed to cover the whole service addressing space offered by micro-segment SRv6. The route owner is SRv6.

The tunnel table is not used directly in the SRv6 locator resolution, in SID resolution, or in packet forwarding. All resolution is performed in the RTM and forwarding is performed in the FIB.

Each resolved remote locator or local adjacency creates an entry in TTM (ROUTE_OWNER_SRV6_ISIS). The entries for remote locators and local adjacencies in the RTM and FIB point to the tunnel ID of this tunnel. The TTM entry is not used directly for forwarding SRv6 packets. However, the route resolution behavior for SRv6 services can be modified to preferentially resolve in TTMv6. See SRv6 policy support for Layer 2 and Layer 3 services for more information.

The SRv6 locator and adjacency routes in route table can be used to forward the following user and CPM originated packets:

• user packets

• ICMPv6 echo request and echo reply packets as described in 7450 ESS, 7750 SR, 7950 XRS, and VSR OAM and Diagnostics Guide

• UDP traceroute packets as described in 7450 ESS, 7750 SR, 7950 XRS, and VSR OAM and Diagnostics Guide

Forwarding and terminating of any other CPM originated packets are not supported. Specifically, received management protocol and control plane protocol packets that are encapsulated in SRv6 are dropped.

If the user configures the address of a BGP neighbor, an LDP peer, or an RSVP-TE LSP destination to match a locator prefix or a SID, packets are forwarded over the SRv6 tunnel but are dropped at the destination router.

The SRv6 processing is performed inline in the IP datapath when forwarding service packets over a shortest path SRv6 tunnel at service origination or when terminating an SRv6 packet with the service SID in the DA field of the outer IPv6 header.

SRv6 processing is performed in a specialized SRv6 Forwarding Path Extension (FPE) when forwarding service packets over an SRv6 policy or when terminating an SRv6 packet with a local node SID in the DA field and the service SID in the SRH.

The SRv6 origination and termination cannot share the same FPE. A single FPE can be configured for SRv6 origination. One or more FPEs can be configured for SRv6 termination.

The following figure shows a packet walk-through including the service origination and termination without SRv6 FPE.

The following figure shows a packet walk-through including the service origination and termination with SRv6 FPE.

The DA field of the IPv6 header contains a single SID is of the form 2001:db8:00d1:d547::

Multiple SIDs in the DA field and eventually in the SRH illustrate the following micro-segment SRv6 behavior.

Transit routers in micro-segment SRv6 illustrates the preceding example.

Node F does the same (based on matching on its own identifier).

Node D does the same but processes the packet in the service corresponding to the identifier.

It can be that the path is longer than the number of micro-SIDs that can be compressed in 128 bits. In that case, an SRH is used to convey the rest of the path. Each container in the SRH must be of the same form (a block part followed by a sequence of micro-SIDs). At some node along the path, because of the shift operations, the container in the IPv6 DA expires. At that node, micro-segment SRv6 implements a regular SRv6 END function (or END.X function if the match is on a uA).

For example, if node B receives a packet with 2001:0db8:00b1:: in the DA field, it detects that its own identifier is followed by an EoC. Node B copies the next segment or container from the SRH in the DA field.

When a service is bound to a SRv6 shortest path tunnel, the ingress service SAP or interface sprays the packets over the ECMP next hops of the SRv6 tunnel and LAG links of the outgoing network interfaces.

The default hash calculation on the ingress service SAP or interface is based on the existing hash procedures of an IPv4, IPv6, or an Ethernet packet. For IPv6 service packets, an option is provided to include the packet’s Flow Label field, when not zero, and to hash on the triplet {SA, DA, Flow Label}. The flow-label-load-balancing command is used to enable this behavior on an access or network interface.

The ingress service SAP or interface copies the output of the hash on the inner packet headers into the flow label field of the outer IPv6 header that it pushes on the SRv6 encapsulated packet. This is regardless of whether the flow label is used or not in the computation of the hash on the service packet

When a service is bound to an SRv6 policy, the service packets are first forwarded to the egress network interface of the SRv6 origination FPE to build and push the SRv6 encapsulation. The packets are then handed in to the ingress network interface of the SRv6 origination FPE which sprays the packets over the ECMP next hops of the SRv6 policy and LAG links of the outgoing network interfaces.

The SRv6 origination FPE egress network interface copies the output of the hash on the inner packet headers into the flow label field of the outer IPv6 header that it pushes on the SRv6 encapsulated packet. This is regardless of whether the flow label is used or not in the computation of the hash on the service packet.

The SRv6 origination FPE ingress network interface does not require the flow-label-load-balancing command to be enabled. All SRv6 packets are automatically sprayed to the ECMP next hops of the SRv6 tunnel and LAG links of the outgoing network interfaces using a hash on the triplet {SA, DA, Flow Label} in the SRv6 packet’s outer IPv6 header.

On a transit router, the hashing of SRv6 encapsulated packets can also use the Flow Label field in the outer IPv6 header to provide more entropy to the load-balancing process of SRv6 packets. The flow-label-load-balancing command can be configured on a network interface to hash on the triplet {SA, DA, Flow Label}. By default, a transit router only hashes on the tuple {SA, DA} in the header of a received IPv6 packet with a non-zero flow label field, including when the packet is SRv6. The description of the flow-label-load-balancing command and the detailed behavior of the hash feature based on the IPv6 packet flow label field and its general application to access and network interfaces is described in section IPv6 Flow Label Load Balancing of the 7450 ESS, 7750 SR, 7950 XRS, and VSR Interface Configuration Guide.

The following describes the interaction of the SRv6 feature with other datapath features:

• When SRv6 is enabled on the base router, datapath enables forwarding and receiving SRv6 encapsulated packets on all network interfaces of the router. The datapath, however, drops an SRv6 encapsulated packet if received from or needs forwarding to an access interface (IES, VPRN). A service packet received on either a network interface or an access interface can be encapsulated into a SRv6 packet and forwarded to a network interface.

• SRv6 feature performs concurrently a couple of IPv6 address lookups on a packet received with an SRH. The first lookup is for the current SID in the DA field in the header of the received SRv6 packet and the second is for the next SID in the SRH.

  The datapath repurposes the IPv6 unicast RPF (IPv6 uRPF) check for the next SID lookup, which means the IPv6 uRPF feature cannot be performed on all IPv6 packets received on that interface. CLI enforces this interaction and so SRv6 cannot be enabled in the base router context (config>router>segment-routing>segment-routing-v6) if the IPv6 uPRF check (config>router>if>ipv6>urpf) is enabled on one or more network interfaces.

  Conversely, the IPv6 uRPF check cannot be enabled on a network interface if SRv6 is enabled in the base router context.

  Note: SRv6 does not impact uRPF checks of IPv4 packets received on a network interface.

• When SRv6 is enabled in one or more IGP instances, a transit router cannot check the SA field in the outer IPv6 header of a SRv6 encapsulated packet received on a network interface and that also has an SRH header. Normally an IPv6 packet which uses 0::0 or a link-local address format should be dropped. All other IPv6 packets, including a SRv6 encapsulated packet that does not have an SRH header, are checked for these two situations.

• Policy Based Routing (PBR) is allowed on flows of packets of an SRv6 tunnel. In other words, the user can apply an ACL filter on a network interface which matches on the outer SA and DA fields of the SRv6 packet and execute an action such as a redirection.

  The operator must ensure that SRv6 matching packets are directed to a router that can process and forward the SRv6 packets.

  Note: Redirecting an SRv6 packet even to an SRv6-capable router is not recommended because the processing of the SID list in the SRH can create loops for any of the SIDs in the outer DA and SRH.

The base LFA, remote LFA, and TI-LFA features operate with SRv6 tunnels in the same way as with SR-MPLS tunnels.

The max-srv6-frr-sids command option configures the maximum number of SRv6 SIDs allowed in the segment list of a TI-LFA repair tunnel. A higher max-srv6-frr-sids value results in better coverage by TI-LFA, at the expense of increased packet encapsulation overhead. The SR OS implementation can insert up to 1 additional regular SID or up to 3 additional micro SIDs in the segment list of a TI-LFA repair tunnel.

The max-srv6-frr-sids parameter is used by TI-LFA to limit the search for the P-Q set in the post-convergence path. Users can configure the following values:

• 0

  The IGP LFA SPF restricts the search to TI-LFA backup next hop, which does not require a repair tunnel. This means that the P and Q nodes are the same and match a neighbor of the LFA SPF computing router.

• 1 (default)

  This option corresponds to a repair tunnel to the node SID of a PQ node (P=Q) or to an adjacency SID between adjacent P and Q nodes. With regular 128-bit SIDs, an SRv6 adjacency is globally routable, therefore there is no need to insert the node SID of the P node; the adjacency SID between the P and Q nodes is sufficient.

  With micro-segment SRv6, an adjacency SID is globally routable only if it is combined with the corresponding node SID (<uN,uA>). In that case and in all other cases, the combination counts as a single SID toward the limit configured by max-srv6-frr-sids.

• 2 to 3

  When protecting a node SID, the IGP LFA SPF widens the search to include a repair tunnel to a P-Q set in which P and Q nodes are interconnected with two to three adjacencies. IGP can also protect an adjacency using the backup path of the neighbor’s node SID. In this case, the neighbor’s node SID is added to the SIDs of the adjacencies between the P and Q nodes, for a total of two to three SIDs.

  With micro-segment SRv6, the addition of the neighbor's node SID can exceed the max-srv6-frr-sids value as long as it fits in the same LFA SRH container.

The following is a description of the SRv6 IS-IS tunnel backup path computation. A compression of the SIDs is applied to minimize the SID list of the computed backup path.

The backup path of a remote locator is as follows:

• TI-LFA

  IS-IS adds the segment list of node and adjacency SIDs of the P-Q set to the repair tunnel. The datapath encodes the top SID of this segment list into the DA field of the outer IPv6 header and moves the received SID value in the DA field and the remaining SIDs of the repair tunnel segment list into the LFA SRH. The protected locator prefix backup next hop in the route table points to the tunnel ID of the locator prefix of the top SID of the P-Q set segment list.

• base LFA

  If an alternate equal-cost parallel link to the LFA neighbor exists, IS-IS programs it as a regular IP next hop of the protected locator.

  If the alternate parallel link to the LFA neighbor is not equal-cost, IS-IS programs a null SID repair tunnel. The datapath does not push an LFA SRH in this case. The protected locator prefix backup next hop in the route table points to the tunnel ID of the local adjacency over the outgoing link to the LFA neighbor.

• remote LFA

  IS-IS adds the node SID of the PQ node to the repair tunnel. The datapath encodes this SID into the DA field of the outer IPv6 header and moves the received SID value of the DA field into the LFA SRH. The protected locator prefix backup next hop in the route table points to the tunnel ID of the locator prefix of the PQ node.

  Note: If the P node is a neighbor of the computing node, the SID list is empty and the backup next hop of the protected locator prefix in the route table points to the tunnel ID of the local adjacency over the outgoing link to the LFA neighbor.

The backup path of a local adjacency is as follows:

• TI-LFA

  IS-IS computes the repair tunnel by using the segment list of the P-Q set plus a node SID of the neighbor node on the other side of the protected adjacency. If the Q node is the same as the neighbor node on the other side of the protected adjacency, the repair tunnel is programmed after compressing the SID list to the adjacency SIDs of the links between the P node and the neighbor node. The datapath encodes the top SID of this segment list into the DA field of the outer IPv6 header and moves the received SID value in the DA field and the remaining SIDs of the repair tunnel segment list into the LFA SRH.

• base LFA

  IS-IS attempts first to program a null SID repair tunnel by using the adjacency of an alternate parallel link to the neighbor on the other side of the protected adjacency. The datapath does not push an LFA SRH in this case. The protected locator prefix backup next hop in the route table points to the tunnel ID of the local adjacency over the outgoing link to the LFA neighbor.

  If the first option fails, IS-IS programs a repair tunnel by using the node SID of the neighbor on the other side of the protected adjacency. The datapath encodes that node SID of the neighbor into the DA field of the outer IPv6 header and moves the received value of the DA field into the LFA SRH.

• remote LFA

  IS-IS computes the repair tunnel by using the node SID of the PQ node plus a node SID of the neighbor node on the other side of the protected adjacency. If the PQ node is one hop from the node on the other side of the protected adjacency, the repair tunnel SID list is compressed to the adjacency SID of the link between the PQ node and the neighbor node. The datapath encodes the top SID of this segment list into the DA field of the outer IPv6 header and moves the received SID value in the DA field and the remaining SIDs of the repair tunnel segment list into the LFA SRH.

The following are examples of MTU settings of the SRv6 origination FPE interface (interface-b):

• all default values

  By default, LFA is disabled in IS-IS. The network interface default MTU is 9786 bytes based on default Ethernet MTU of 9800 bytes.

  The SRv6 origination FPE interface MTU defaults to the same value of 9786 bytes; there is no need for further adjustments.

• all default values and RLFA or TI-LFA enabled

  The user must adjust the SRv6 origination FPE interface MTU from the first bullet item case to account for the 24 bytes introduced by LFA.

  SRv6 origination FPE Interface MTU is 9786 - 24 = 9762 bytes.

• a remote constrained network interface and RLFA or TI-LFA enabled

  Assume a specific remote network interface in the SRv6 network is limited to a maximum value of 1500 bytes. The user must adjust the SRv6 origination FPE interface MTU in all the ingress PEs from the first bullet item case, to account for that constrained value, plus the 24 bytes introduced by LFA repair tunnel (Users can adjust for as many LFA SRHs as they need. The following example assumes 1 LFA SRH).

  SRv6 origination FPE Interface MTU = 1500 - 24 = 1476 bytes.

SRv6 processing is performed in a specialized SRv6 FPE when forwarding service packets over a SRv6 policy or when terminating a SRv6 packet with a local node SID in the DA field and the service SID in the SRH. The SRv6 FPE also processes service packets forwarded over a SRv6 shortest path tunnel when the service SID in the DA field matches a non-locator IPv6 route in the FIB. A non-locator IPv6 route is an ISIS route of the locator prefix advertised without a locator TLV, a static route, an OSPF route, or a BGP route of the locator prefix.

The following guidelines apply for the SRv6 FPE:

• An internal or external Port Cross-Connect (PXC) can be used for the SRv6 FPE.

• The SRv6 origination or termination FPE cannot be shared with other applications, but the same physical ports can be used when configuring PXC ports for multiple FPEs of different applications.

  As an example of how two FPEs can share the same physical port (therefore the same bandwidth), define two PXC ports, both sharing the same underlaying physical port; for instance:

  FPE 1 is associated with PXC-1 and FPE 2 is associated with PXC-2, where PXC-1 and PXC-2 are both assigned to port 1/1/1

• Some considerations about the SRv6 termination FPE follow:

  • It is configured per locator.

  • Multiple locators can optionally use the same or different FPE.

  • Received SRv6 traffic for a specific (local) locator is redirected to the SRv6 termination FPE interface-a.

• Some considerations about the SRv6 origination FPE follow:

  • There is only one SRv6 origination FPE supported per system.

  • The SRv6 origination and termination FPEs are always different.

• SRv6 FPE redundancy and load-balancing:

  • Each FPE can use a LAG composed of as many PXC ports as needed (there is no specific limitation in the number of PXC members per LAG).

  • LAG members can be PXC ports in the same or a different card.

The following CLI is required to create the FPE of type srv6 origination or termination and apply it to a locator. All locators may be associated with the same or a different FPE.

configure
+--fwd-path-ext
   +--fpe <fpe-id>
      +--application
         +--srv6 <origination|termination> 
            +--interface-a
               +--qos <network-policy-id>
            +--interface-b
               +--mtu <1280-9786>
               +--qos <network-policy-id>

configure
+--router
|    +--segment-routing
|    |    +--segment-routing-v6
|    |    |    +--origination-fpe <fpe>
|    |    |    +--source-address <ipv6-address>
|    |    |    +--locator <locator-name>
|    |    |    |    +--termination-fpe <fpe>

VPRN services support SRv6 End.DT4, End.DT6, and End.DT46 behaviors. VPRNs support IPv4 and IPv6 routes that are advertised in VPN-IPv4 and VPN-IPv6 families, as well as in EVPN IP prefix routes in the Interface-less mode.

The following classic CLI commands configure a VPRN for SRv6 with the VPN-IP families.

configure
+--service
|   +---vprn <service-id>
|   |   +---segment-routing-v6 <instance-id>
|   |   |   +---locator <locator-name>
|   |   |   |   +---function
|   |   |   |   |   +---end-dt4 <integer>
|   |   |   |   |   +---end-dt6 <integer>
|   |   |   |   |   +---end-dt46 <integer>
|   |   +---bgp-ipvpn
|   |   |   +---segment-routing-v6 <bgp-instance-id>
|   |   |   |   +---srv6-instance <id> default-locator <name>
|   |   |   |   +---source-address <ipv6-address>
|   |   |   |   +---route-distinguisher <rd>  
|   |   |   |   +---vrf-export  
|   |   |   |   +---vrf-import  
|   |   |   |   +---vrf-target  
|   |   |   |   +---default-route-tag <number>
|   |   |   |   +---shutdown

The following MD-CLI commands configure a VPRN for SRv6 with the VPN-IP families.

configure
+--service
|   +---vprn <service-id>
|   |   +-- segment-routing-v6 <number>
|   |   |   +-- apply-groups <reference>
|   |   |   +-- apply-groups-exclude <reference>
|   |   |   +-- locator <reference>
|   |   |       +-- apply-groups <reference>
|   |   |       +-- apply-groups-exclude <reference>
|   |   |       +-- function
|   |   |           +-- end-dt4
|   |   |           |   +-- value <number>
|   |   |           +-- end-dt46
|   |   |           |   +-- value <number>
|   |   |           +-- end-dt6
|   |   |           |   +-- value <number>
|   |   +---bgp-ipvpn
|   |   |   +-- segment-routing-v6 <number>
|   |   |       +-- admin-state <keyword>
|   |   |       +-- apply-groups <reference>
|   |   |       +-- apply-groups-exclude <reference>
|   |   |       +-- default-route-tag <number>
|   |   |       +-- domain-id <string>
|   |   |       +-- evi <number>
|   |   |       +-- route-distinguisher <string | keyword>
|   |   |       +-- source-address <global-unicast-ipv6-address>
|   |   |       +-- srv6
|   |   |       |   +-- default-locator <reference>
|   |   |       |   +-- instance <reference>
|   |   |       +-- vrf-export
|   |   |       |   +-- apply-groups <reference>
|   |   |       |   +-- apply-groups-exclude <reference>
|   |   |       |   +-- policy <string | reference>
|   |   |       +-- vrf-import
|   |   |       |   +-- apply-groups <reference>
|   |   |       |   +-- apply-groups-exclude <reference>
|   |   |       |   +-- policy <string | reference>
|   |   |       +-- vrf-target
|   |   |           +-- community <string>
|   |   |           +-- export-community <string>
|   |   |           +-- import-community <string>

The following classic CLI commands configure a VPRN for SRv6 with EVPN-IFL.

configure
+--service
|   +---vprn <service-id>
|   |   +-- segment-routing-v6 <number>
|   |   |   +-- apply-groups <reference>
|   |   |   +-- apply-groups-exclude <reference>
|   |   |   +-- locator <reference>
|   |   |       +-- apply-groups <reference>
|   |   |       +-- apply-groups-exclude <reference>
|   |   |       +-- function
|   |   |           +-- end-dt4
|   |   |           |   +-- value <number>
|   |   |           +-- end-dt46
|   |   |           |   +-- value <number>
|   |   |           +-- end-dt6
|   |   |           |   +-- value <number>
|   |   +---bgp-evpn
|   |   |   +---segment-routing-v6 <bgp-instance-id>
|   |   |   |   +---srv6-instance <id> default-locator <name>
|   |   |   |   +---source-address <ipv6-address>
|   |   |   |   +---route-distinguisher <rd>  
|   |   |   |   +---vrf-export  
|   |   |   |   +---vrf-import  
|   |   |   |   +---vrf-target  
|   |   |   |   +---default-route-tag <number>
|   |   |   |   +---shutdown

The following MD-CLI commands configure a VPRN for SRv6 with EVPN-IFL.

configure
+--service
|   +---vprn <service-id>
|   |   +-- segment-routing-v6 <number>
|   |   |   +-- apply-groups <reference>
|   |   |   +-- apply-groups-exclude <reference>
|   |   |   +-- locator <reference>
|   |   |       +-- apply-groups <reference>
|   |   |       +-- apply-groups-exclude <reference>
|   |   |       +-- function
|   |   |           +-- end-dt4
|   |   |           |   +-- value <number>
|   |   |           +-- end-dt46
|   |   |           |   +-- value <number>
|   |   |           +-- end-dt6
|   |   |           |   +-- value <number>
|   |   +---bgp-evpn
|   |   |   +-- segment-routing-v6 <number>
|   |   |       +-- admin-state <keyword>
|   |   |       +-- apply-groups <reference>
|   |   |       +-- apply-groups-exclude <reference>
|   |   |       +-- default-route-tag <number>
|   |   |       +-- domain-id <string>
|   |   |       +-- evi <number>
|   |   |       +-- resolution <keyword>
|   |   |       +-- route-distinguisher <string | keyword>
|   |   |       +-- source-address <global-unicast-ipv6-address>
|   |   |       +-- srv6
|   |   |       |   +-- default-locator <reference>
|   |   |       |   +-- instance <reference>
|   |   |       +-- vrf-export
|   |   |       |   +-- apply-groups <reference>
|   |   |       |   +-- apply-groups-exclude <reference>
|   |   |       |   +-- policy <string | reference>
|   |   |       +-- vrf-import
|   |   |       |   +-- apply-groups <reference>
|   |   |       |   +-- apply-groups-exclude <reference>
|   |   |       |   +-- policy <string | reference>
|   |   |       +-- vrf-target
|   |   |           +-- community <string>
|   |   |           +-- export-community <string>
|   |   |           +-- import-community <string>

The associated locator must be configured to enable SRv6 on the VPRN service. In addition, the following rules apply:

• The function value can either be statically configured or dynamically allocated.

• Any Layer 3 function behavior can be configured, although VPN-IPv4 and EVPN-IFL IPv4 routes are advertised with end-dt4 or end-dt46 in that preference order (if they exist) and VPN-IPv6 and EVPN-IFL IPv6 routes are advertised with end-dt6 or end-dt46 in that preference order.

• The VPRN or label mode is not relevant to SRv6 and setting it has no effect on the behavior of the SRv6 feature.

• The following are supported:

  • BGP-IPVPN and BGP-EVPN (EVPN-IFL) families are simultaneously supported in the same VPRN where SRv6 is enabled.

  • Up to two BGP instances per VPRN are supported.

  • The two BGP instances can be associated with the same family or different families.

  • A family can have two BGP instances of SRv6 encapsulation.

  • In addition, two BGP-IPVPN instances can be configured with SRv6 and MPLS encapsulations respectively. Two BGP-EVPN instances can also be configured with SRv6 and MPLS encapsulations, respectively.

• The following applies to VPRN feature interaction with SRv6:

  • The following commands under the VPRN context only operate on MPLS encapsulations:

    • class-forwarding

    • entropy-label

    • hash-label

    • label-mode

    • ttl-propagate

  • The following commands under the VPRN context are mutually exclusive with SRv6:

    • carrier-carrier-vpn

    • network-interface

    • export-inactive-bgp

  • The following VPRN commands and features operate on MPLS and SRv6 encapsulations:

    • vprn-type

    • allow-export-bgp-vpn

    • ecmp-unequal-cost

    • bgp-vpn-backup

    • Unicast protocols on PE-CE interfaces

    • Commands such as ipsec, nat, and subscriber-interfaces are supported (no interaction).

    • ECMP and edge PIC are supported for SRv6 and also across routes of the same family with different encapsulations; for example, the same prefix is resolved to SRv6 and MPLS tunnels.

    • Route target-based leaking is supported for SRv6 routes in the VPRN.

As is the case with existing MPLS encapsulation, BGP Path Attribute Propagation between BGP owners of the same VPRN route table is supported, including routes with SRv6 encapsulation.

• BGP Path Attribute propagation for SRv6 routes does not require enabling a CLI knob

• In cases where multiple BGP owners coexist in the same VPRN route table with a single instance, propagation is supported in the following cases, irrespective of the encapsulation of the route (MPLS or SRv6):

  • VPN-IPv4/6 ← → EVPN-IFL

  • VPN-IPv4/6 ← → VPN-IPv4/6 – when allow-export-bgp-vpn is enabled

  • EVPN-IFL← → EVPN-IFL – when allow-export-bgp-vpn is enabled

  • VPN-IPv4/6 ← → IPv4/v6

  • EVPN-IFL ← → IPv4/v6

  • VPN-IPv4/6 ← → EVPN-IFF (requires iff-attribute-uniform-propagation)

  • EVPN-IFL ← → EVPN-IFF (requires iff-attribute-uniform-propagation)

• In the case of multi-instance bgp VPRNs, VPN-IPv4/6 and EVPN-IFL routes received in one instance are readvertised into the other instance, including all the BGP Path Attributes of the original route.

• The following attributes are filtered out before the path attributes are propagated in all the previously described cases:

  • all type 0x06 extended communities

  • the BGP encapsulation extended community

  • the BGP encapsulation attribute

  • the BGP Prefix-SID attribute (which includes SRv6 Service SID TLVs)

  • all Route Target extended communities

To allow a seamless migration from MPLS tunnels to SRv6 in VPRN services, both MPLS auto-bind tunnels and SRv6 are supported in the same VPRN service.

Routes for the same prefix follow regular route table selection in the VPRN. At the end of the selection process, if there are still SRv6 and MPLS routes, the SRv6 route is selected first and the MPLS route is removed from consideration.

In the base router BGP instance, BGP routes may be originated, propagated or received with SRv6 TLVs in the prefix SID attribute. The processing rules are expected to use the following logic:

• A VPN-IPv4 or VPN-IPv6 route that is imported by the base router BGP instance from a VPRN (through the VRF export process), and that already has a prefix SID attribute with an SRv6 TLV at this stage, is advertised to all VPN-IPv4 and VPN-IPv6 peers of the base router BGP instance, with the next-hop-self as normal. There is no option to strip the SRv6 TLV or prefix SID attribute toward any of these peers, however, there is an option to drop the entire route toward selected peers or groups. This is similar to the effect of a BGP export policy that drops the route, but route policies cannot match routes based on the presence of an SRv6 TLV.

• An IPv6 route that is imported by the base router BGP instance from another protocol’s route that was added to base router route table (static, OSPF, IS-IS, and so on) does not have a prefix SID attribute carrying the SRv6 TLV added to it by default. Adding a prefix SID can only be achieved by configuring the config>router>bgp>segment-routing-v6>family ipv6 add-srv6-tlvs command; however, this command also has the effect of adding a prefix SID attribute with SRv6 TLV to BGP IPv6 routes received from other peers without the SRv6 TLV and that are propagated to other family IPv6 peers with next-hop-self applied.

• Any BGP route received with a prefix SID attribute carrying SRv6 TLVs that is not an imported VPN-IPv4, VPN-IPv6, or EVPN route or an IPv6 unlabeled unicast route is treated the same as an existing route, that is, by ignoring the prefix SID attribute contents, resolving the route based only on its BGP next hop, and propagating the prefix SID attribute to other peers unchanged.

• If an IPv6 unlabeled unicast route is received with a prefix SID attribute carrying an SRv6 TLV and the config>router>bgp>segment-routing-v6>family ipv6 ignore-received-srv6-tlvs command is configured, that route is treated the same as an existing route, that is, by ignoring the prefix SID attribute contents, resolving the route based only on its BGP next hop, and propagating the attribute to other peers unchanged, irrespective of the next-hop-self.

• If an IPv6 unlabeled unicast route is received with a prefix SID attribute carrying an SRv6 TLV and the config>router>bgp>segment-routing-v6>family ipv6 ignore-received-srv6-tlvs command is set to FALSE, that route is considered resolved only if its BGP next hop is reachable and the locator prefix is reachable. The datapath or FNH programming and IGP cost to reach the next hop (used by the BGP decision process) is based on the route to the locator prefix. The IPv6 route is propagated to other family IPv6 peers with the prefix SID attribute and its SRv6 TLV unchanged, irrespective of the next-hop-self.

• An IPv6 unlabeled unicast route that is received without a prefix SID attribute containing an SRv6 TLV does not have a prefix-SID attribute carrying the SRv6 TLV added to it by default, even if it is re-advertised with the next-hop-self applied. This can only be achieved by configuring the config>router>bgp>segment-routing-v6>family ipv6 add-srv6-tlvs; however, this command also has the effect of adding a prefix SID attribute with SRv6 TLV to imported or redistributed routes.

configure
+--router
   +--segment-routing
|   |   +--- base-routing-instance
|   |   |   |   locator <locator-name>
|   |   |   |   +---function
|   |   |   |   |   +---end-dt6 <integer>

configure
+--router
   +--bgp
      +--segment-routing-v6
         +--source-address <ipv6-address>
         +--family* 
            +--add-srv6-tlvs
            |  +--locator <locator-name>
            +--ignore-received-srv6-tlvs

Epipe services support SRv6 End.DX2 behavior. Currently, the SRv6 SID for End.DX2 is signaled by EVPN-VPWS AD per-EVI routes.

Use the following CLI commands to configure an Epipe service for SRv6:

+--epipe
   +--segment-routing-v6 <instance-id> 
   |  +--locator <locator-name>  
   |  |  +--function 
   |  |  |  +--end-dx2 <integer>
   |  +--bgp-evpn
   |  |  +-- segment-routing-v6 <number>
   |  |  |   +-- admin-state <keyword>
   |  |  |   +-- default-route-tag <number>
   |  |  |   +-- ecmp <number>
   |  |  |   +-- force-vc-forwarding <keyword>
   |  |  |   +-- oper-group <reference>
   |  |  |   +-- route-next-hop
   |  |  |   |   +-- ip-address <ip-address>
   |  |  |   |   +-- system-ipv4
   |  |  |   |   +-- system-ipv6
   |  |  |   +-- source-address <global-unicast-ipv6-address>
   |  |  |   +-- srv6
   |  |  |       +-- default-locator <reference>
   |  |  |       +-- instance <reference>

Where the following conditions apply:

• The SRv6 Epipe is configured with the locator that is used. This determines the SID structure and value that is advertised in the AD per EVI route for the service.

• A single SRv6 instance with a single locator is supported on Epipes.

• The SRv6 Epipe uses an End.DX2 function value that, if not configured, is dynamically allocated by the system, out of the dynamic range available for the locator. If the end-dx2 function is configured, then this value is used instead of a dynamic value.

• The following is supported in SRv6 Epipes:

  ecmp

  used for aliasing on remote SRv6 EVPN ES destinations

  force-vlan-vc-forwarding

  used to preserve one VLAN tag in the payload of the SRv6 tunnel. On termination, the VLAN tag is transparently passed through the termination SRv6 FPE.

  default-route-tag

  used to allow easy matching of the service routes on export policies

  oper-group

  required for fault-propagation and fate-sharing with the monitoring objects

  route-next-hop

  required to control the advertised BGP next hop for the EVPN AD per-EVI route. When EVPN Multihoming is used, this value must match the ES originating-ip and the ES route-next-hop value.

EVPN-VPWS is the control plane technology to signal SRv6 Epipes. The local-attachment-circuit Ethernet-tag value is advertised in an AD per-EVI route that may have a zero or non-zero ESI (if multihoming is used). The AD per-EVI routes are advertised along with the Layer-2 SRv6 Services TLV encoding with an End.DX2 behavior and using the transposition procedures described in Transposition procedures when advertising service routes. Upon reception the ingress PE creates an EVPN destination, as long as the received route includes the remote expected Ethernet-tag and route-target. The following CLI excerpt shows a configuration example and the created EVPN SRv6 destination on the PE:

*A:PE-3# configure service epipe 200 
*A:PE-3>config>service>epipe# info 
----------------------------------------------
            segment-routing-v6 1 create
                locator "LOC-1"
                    function
                        end-dx2 200
                    exit
                exit
            exit
            bgp
            exit
            bgp-evpn
                local-attachment-circuit ac-23 create
                    eth-tag 23
                exit
                remote-attachment-circuit ac-5 create
                    eth-tag 5
                exit
                evi 200
                segment-routing-v6 bgp 1 srv6-instance 1 default-locator "LOC-1" create
                    source-address 2001:db8::3
                    ecmp 2
                    route-next-hop system-ipv6
                    no shutdown
                exit
            exit
            sap lag-1:200 create
                no shutdown
            exit
            no shutdown
----------------------------------------------
*A:PE-3>config>service>epipe# /show service id 200 segment-routing-v6 destinations 

===============================================================================
TEP, SID
===============================================================================
Instance  TEP Address                        Segment Id
-------------------------------------------------------------------------------
1         2001:db8::5                        cafe:1:0:5:c:8000::
-------------------------------------------------------------------------------
Number of TEP, SID: 1
-------------------------------------------------------------------------------
===============================================================================

===============================================================================
Segment Routing v6 Ethernet Segment Dest
===============================================================================
Instance  Eth SegId                       Num. Macs     Last Change
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================

SRv6 Epipes support EVPN Multihoming. Their associated Ethernet Segments (ES) can be shared among MPLS services and other SRv6 services.

EVPN Multihoming for SRv6 Epipes follows these guidelines:

• The ES used by SRv6 Epipes is only supported in evi-rt mode, therefore separate AD per-ES routes per service are advertised for SRv6 Epipes.

• If evi-rt-set is configured in the ES, the SRv6 services are skipped when packing route-targets for the AD per-ES route. This is the same behavior as having a Epipe services with a configured vsi-export policy; the system also skips the route-targets for Epipes with vsi-export when packing multiple route-targets in the same AD per-ES route.

• The advertised AD per-ES route for the SRv6 Epipe includes a Layer-2 SRv6 Services TLV with a SID value of zero. The used behavior code point is End.DT2M. In addition, the AD per-ES route is also advertised with an ESI Label extended community that encodes the implicit-null value in the ESI label field. A debug example of a received AD per-ES route for SRv6 follows:

  22 2021/05/21 18:23:10.247 UTC MINOR: DEBUG #2001 Base Peer 1: 2001:db8::2
  "Peer 1: 2001:db8::2: UPDATE
  Peer 1: 2001:db8::2 - Received BGP UPDATE:
      Withdrawn Length = 0
      Total Path Attr Length = 125
      Flag: 0x90 Type: 14 Len: 48 Multiprotocol Reachable NLRI:
          Address Family EVPN
          NextHop len 16 Global NextHop 2001:db8::2
          Type: EVPN-AD Len: 25 RD: 192.0.2.2:200 ESI: 01:d8:47:ff:00:00:00:00:01:
  00, tag: MAX-ET Label: 0 
      Flag: 0x40 Type: 1 Len: 1 Origin: 0
      Flag: 0x40 Type: 2 Len: 0 AS Path:
      Flag: 0x40 Type: 5 Len: 4 Local Preference: 100
      Flag: 0xc0 Type: 16 Len: 16 Extended Community:
          target:64500:200
          esi-label:3/Single-Active
      Flag: 0xc0 Type: 40 Len: 37 Prefix-SID-attr:
         SRv6 Services TLV (37 bytes):-
           Type: SRV6 L2 Service TLV (6)
           Length: 34 bytes, Reserved: 0x0
           SRv6 Service Information
           Service Information Sub-TLV Type 1
              Type: 1 Len: 30 Rsvd1: 0x0
              SRv6 SID: ::
              SID Flags: 0x0 Endpoint Behavior: 0x18 Rsvd2: 0x0
              SRv6 SID Sub-Sub-TLV
                 Type: 1 Len: 6
                 BL:0 NL:0 FL:0 AL0 TL:0 TO:0
  

The creation of ES destinations follows the same rules as in EVPN-VPWS services with MPLS transport, except that the ES destination is resolved to remote SRv6 SIDs, as shown in the following example:

*A:PE-5# show service id 200 segment-routing-v6 destinations 

===============================================================================
TEP, SID
===============================================================================
Instance  TEP Address                        Segment Id
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================

===============================================================================
Segment Routing v6 Ethernet Segment Dest
===============================================================================
Instance  Eth SegId                       Num. Macs     Last Change
-------------------------------------------------------------------------------
1         01:d8:47:ff:00:00:00:00:01:00   0             06/18/2021 17:04:15
-------------------------------------------------------------------------------
Number of entries: 1
-------------------------------------------------------------------------------
===============================================================================
*A:PE-5# show service id 200 segment-routing-v6 esi 01:d8:47:ff:00:00:00:00:01:00 

===============================================================================
Segment Routing v6 Ethernet Segment Dest
===============================================================================
Instance  Eth SegId                       Num. Macs     Last Change
-------------------------------------------------------------------------------
1         01:d8:47:ff:00:00:00:00:01:00   0             06/18/2021 17:04:15
-------------------------------------------------------------------------------
Number of entries: 1
-------------------------------------------------------------------------------
===============================================================================

===============================================================================
Segment Routing v6 Dest TEP Info
===============================================================================
Instance  TEP Address                   Segment Id          Last Change
-------------------------------------------------------------------------------
1         2001:db8::2                   cafe:1:0:2:c:8000:: 06/18/2021 17:04:15
-------------------------------------------------------------------------------
Number of entries : 1
-------------------------------------------------------------------------------
===============================================================================

VPLS services support SRv6 End.DT2M behavior for BUM traffic and End.DT2U behavior for known unicast traffic. The SRv6 SID for End.DT2M is signaled by EVPN Inclusive Multicast Ethernet Tag (IMET) routes, whereas the SID for End.DT2U is signaled along with EVPN MAC/IP routes.

Use the following contexts to configure a VPLS service for SRv6:

• MD-CLI

  configure service vpls "1" segment-routing <instance-id>   
  configure service vpls "1" bgp-evpn segment-routing-v6 <number>  

• classic CLI

  configure service vpls "1" segment-routing-v6 <instance-id>
  configure service vpls "1" bgp-evpn segment-routing-v6 srv6-instance 1 default-locator 

The following conditions apply for a VPLS service for SRv6:

• The SRv6 VPLS is configured using the locator. This determines the SID structure and value that is advertised along with the EVPN IMET and MAC/IP routes for the service.

• A single SRv6 instance with a single locator is supported on VPLS services.

• SRv6 VPLS services use End.DT2M and End.DT2U SIDs. Their corresponding function values, if not configured, are allocated automatically by the router. Dynamic or static, both function values (End.DT2M and End.DT2U) are needed so the EVPN routes for the services are advertised. While both values are different locally on the service, the router accepts the same value for End.DT2M and End.DT2U functions from a remote PE for the same service.

• If the following command is configured on the PEs attached to the same service, the service MTU value is advertised in the EVPN Layer 2 Attributes extended community along with the IMET routes.
  • MD-CLI

    configure service vpls bgp-evpn routes incl-mcast advertise-l2-attributes

  • classic CLI

    configure service vpls bgp-evpn incl-mcast-l2-attributes-advertisement

  Upon receiving the signaled MTU from an egress PE, the ingress PE compares the received and local MTU. In case of a mismatch, the EVPN SRv6 destination goes operationally down, and the operational flag MTU-Mismatch shows the reason. Use the following command to configure the router to ignore the MTU signaled by the remote PE and bring up the SRv6 destination if there are no other reasons to keep it down.

  configure service vpls bgp-evpn ignore-mtu-mismatch

• The following commands are supported in SRv6 VPLS services:

  • force-vlan-vc-forwarding

    This command preserves one VLAN tag in the payload of the SRv6 tunnel.

  • default-route-tag

    This command matches BGP EVPN routes for the service on export policies, typically to add or modify BGP attributes.

  • oper-group

    This command is required for fault-propagation purposes.

  • protected-src-mac-violation-action discard

    This command is required for loop avoidance, along with mac-duplication blackhole.

  • split-horizon-group

    This command is used for seamless integration with spoke SDPs and migration from EVPN-MPLS services (in multi-instance services).

  • route-next-hop

    This command is used to control the BGP next-hop used for service routes. If not configured, it is system-ipv4 by default.

  • source-address

    If not configured, it is inherited from the locator’s source address. The source address does not need to be reachable or even exist on a local interface. This is possible because the source address is not looked up in the datapath at the remote PE.

  • resolution {route-table | tunnel-table | fallback-tunnel-to-route-table}

    This command is used to set the resolution of SRv6 routes in the route table or tunnel table (needed for SRv6 policy), and even a fallback from tunnel to route-table resolution.

A:PE-2# configure service vpls 1900 
A:PE-2>config>service>vpls# info 
            segment-routing-v6 1 create
                locator “LOC-1"
                    function
                        end-dt2u
                        end-dt2m
                    exit
                exit
            exit
            bgp
            exit
            bgp-evpn
                evi 1900
                segment-routing-v6 bgp 1 srv6-instance 1 default-locator "LOC-1" create
                    source-address 2001:db8::2
                    route-next-hop 2001:db8::2
                    no shutdown
                exit
            exit
            stp
                shutdown
            exit
            no shutdown            

show service id 1900 segment-routing-v6 instance 1

===============================================================================
Segment Routing v6 Instance 1 Service 1900
===============================================================================
Locator                                                           
  Type         Function  SID                                     Status
-------------------------------------------------------------------------------
LOC-1
  End.DT2U       *504273 cafe:1:0:2:7b1d:1000::                  ok
  End.DT2M       *504272 cafe:1:0:2:7b1d::                       ok
===============================================================================

show router segment-routing-v6 local-sid end-dt2u end-dt2m 

===============================================================================
Segment Routing v6 Local SIDs
===============================================================================
SID                                               Type           Function
  Locator                                                        
  Context                                                        
-------------------------------------------------------------------------------
cafe:1:0:2:7b1d::                                 End.DT2M       504272
  LOC-1
  SvcId: 1900 Name: bd-1900-srv6
cafe:1:0:2:7b1d:1000::                            End.DT2U       504273
  LOC-1
  SvcId: 1900 Name: bd-1900-srv6
-------------------------------------------------------------------------------
SIDs : 2
-------------------------------------------------------------------------------
===============================================================================

show service id 1900 segment-routing-v6 destinations

===============================================================================
TEP, SID (Instance 1)
===============================================================================
TEP Address                   Segment Id                       Oper  Mcast Num
                                                               State       MACs
-------------------------------------------------------------------------------
2001:db8::3                   cafe:1:0:3:7b1d:7000::           Up    BUM   1
2001:db8::4                   cafe:1:0:4:7:b1db::              Up    BUM   0
2001:db8::5                   cafe:1:0:5:7b1d:d000::           Up    BUM   0 
2001:db8::5                   cafe:1:0:5:7b1d:e000::           Up    None  1
-------------------------------------------------------------------------------
Number of TEP, SID: 4
-------------------------------------------------------------------------------
===============================================================================

===============================================================================
Segment Routing v6 Ethernet Segment Dest
===============================================================================
Instance  Eth SegId                       Num. Macs     Last Change
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================

show router bgp routes evpn incl-mcast community target:64500:1900 next-hop 2001:db8::5 hunt 

===============================================================================
 BGP Router ID:192.0.2.2        AS:64500       Local AS:64500      
===============================================================================
 Legend -
 Status codes  : u - used, s - suppressed, h - history, d - decayed, * - valid
                 l - leaked, x - stale, > - best, b - backup, p - purge
 Origin codes  : i - IGP, e - EGP, ? - incomplete

===============================================================================
BGP EVPN Inclusive-Mcast Routes
===============================================================================
-------------------------------------------------------------------------------
RIB In Entries
-------------------------------------------------------------------------------
Network        : n/a
Nexthop        : 2001:db8::5
Path Id        : None                   
From           : 2001:db8::5
Res. Nexthop   : fe80::b449:1ff:fe01:1f
Local Pref.    : 100                    Interface Name : int-PE-2-PE-5
Aggregator AS  : None                   Aggregator     : None
Atomic Aggr.   : Not Atomic             MED            : None
AIGP Metric    : None                   IGP Cost       : 10
Connector      : None
Community      : target:64500:1900
Cluster        : No Cluster Members
Originator Id  : None                   Peer Router Id : 192.0.2.5
Flags          : Used Valid Best IGP 
Route Source   : Internal
AS-Path        : No As-Path
EVPN type      : INCL-MCAST             
Tag            : 0                      
Originator IP  : 2001:db8::5
Route Dist.    : 192.0.2.5:1900
Route Tag      : 0                      
Neighbor-AS    : n/a
Orig Validation: N/A                    
Source Class   : 0                      Dest Class     : 0
Add Paths Send : Default                
Last Modified  : 00h14m18s              
SRv6 TLV Type  : SRv6 L2 Service TLV (6)
SRv6 SubTLV    : SRv6 SID Information (1)
Sid            : cafe:1:0:5::
Full Sid       : cafe:1:0:5:7b1d:d000::
Behavior       : End.DT2M (24)
SRv6 SubSubTLV : SRv6 SID Structure (1)
Loc-Block-Len  : 32                     Loc-Node-Len   : 32
Func-Len       : 20                     Arg-Len        : 0
Tpose-Len      : 20                     Tpose-offset   : 64
-------------------------------------------------------------------------------
PMSI Tunnel Attributes : 
Tunnel-type    : Ingress Replication    
Flags          : Type: RNVE(0) BM: 0 U: 0 Leaf: not required
MPLS Label     : 8068560                
Tunnel-Endpoint: 2001:db8::5
-------------------------------------------------------------------------------
 
-------------------------------------------------------------------------------
RIB Out Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Routes : 1
===============================================================================      

show router bgp routes evpn mac community target:64500:1900 next-hop 2001:db8::5 hunt

===============================================================================
 BGP Router ID:192.0.2.2        AS:64500       Local AS:64500      
===============================================================================
 Legend -
 Status codes  : u - used, s - suppressed, h - history, d - decayed, * - valid
                 l - leaked, x - stale, > - best, b - backup, p - purge
 Origin codes  : i - IGP, e - EGP, ? - incomplete

===============================================================================
BGP EVPN MAC Routes
===============================================================================
-------------------------------------------------------------------------------
RIB In Entries
-------------------------------------------------------------------------------
Network        : n/a
Nexthop        : 2001:db8::5
Path Id        : None                   
From           : 2001:db8::5
Res. Nexthop   : fe80::b449:1ff:fe01:1f
Local Pref.    : 100                    Interface Name : int-PE-2-PE-5
Aggregator AS  : None                   Aggregator     : None
Atomic Aggr.   : Not Atomic             MED            : None
AIGP Metric    : None                   IGP Cost       : 10
Connector      : None
Community      : target:64500:1900
                 mac-mobility:Seq:0/Static
Cluster        : No Cluster Members
Originator Id  : None                   Peer Router Id : 192.0.2.5
Flags          : Used Valid Best IGP 
Route Source   : Internal
AS-Path        : No As-Path
EVPN type      : MAC                    
ESI            : ESI-0
Tag            : 0                      
IP Address     : n/a
Route Dist.    : 192.0.2.5:1900         
Mac Address    : 00:ca:ca:de:ba:ca      
MPLS Label1    : LABEL 504286           MPLS Label2    : n/a
Route Tag      : 0                      
Neighbor-AS    : n/a
Orig Validation: N/A                    
Source Class   : 0                      Dest Class     : 0
Add Paths Send : Default                
Last Modified  : 00h14m26s              
SRv6 TLV Type  : SRv6 L2 Service TLV (6)
SRv6 SubTLV    : SRv6 SID Information (1)
Sid            : cafe:1:0:5::
Full Sid       : cafe:1:0:5:7b1d:e000::
Behavior       : End.DT2U (23)
SRv6 SubSubTLV : SRv6 SID Structure (1)
Loc-Block-Len  : 32                     Loc-Node-Len   : 32
Func-Len       : 20                     Arg-Len        : 0
Tpose-Len      : 20                     Tpose-offset   : 64
 
-------------------------------------------------------------------------------
RIB Out Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Routes : 1
=============================================================================== 

The router supports BGP extensions for SRv6 policies as defined in draft-ietf-idr-segment-routing-te-policy-11 Advertising Segment Routing Policies in BGP. BGP uses the sr-policy-ipv6 address family for SR policies with SAFI SR Policy (73).

SRv6 segment lists are signaled using a series of SRv6 SID sub-TLVs, as follows:

• Segment sub-TLV Type B – SID only, in the form of an IPv6 address
• SRv6 binding SID sub-TLV

The SRv6 endpoint behavior sub-TLV is not included.

The router supports one binding SID per SRv6 policy. The application of binding SIDs for SRv6 policies is similar to those for SR policies with an MPLS data plane. The binding SID is programmed using the function type End.B6.Encaps.Red (as defined in RFC 8986).

Each tunnel in the tunnel table has a protocol owner. The router programs SRv6 polices in TTMv6 with srv6-pol as protocol owner.

If two SR policies have the same color and endpoint but a different technology (MPLS and SRv6), the router programs a separate tunnel for each.

The router treats the TTM preference for SRv6 policies the same as for MPLS-based SR policies. The router populates the TTMv6 tunnel table with the SRv6 tunnel for the SRv6 policy. IGP provides the most accurate MTU value and programs the SR tunnel MTU value in the TTM. The MTU value includes the lowest MTU among the ECMP next hops or the primary/LFA next hops for each remote locator tunnel and local adjacency SID tunnel.

Next the MTU of the SRv6 policy is derived as follows:

The following services can resolve their next hop over an SRv6 policy in TTMv6:

• VPRNv4
• VPRNv6
• EVPN VPLS and VPWS
• BGP Shortcuts
• EVPN IFL

As with MPLS SR policies, the next hop resolution is based on the color (if present) and on the comparison of the next hop with the SR policy endpoint. The color, the endpoint, and the head end define a matching policy, but a matching policy can be an SR MPLS policy or an SRv6 policy. Therefore, the service also uses the data plane technology of the policy to select the tunnel type to resolve over. The following restrictions apply:

• MPLS services cannot resolve over SRv6 tunnels
• SRv6 services can only resolve over SRv6 tunnels

An SRv6 service cannot fall back to an MPLS tunnel type. Suppose the configuration of the resolution allows an SRv6 policy, but an SRv6 policy with a matching color and endpoint does not exist in TTMv6. In that case, the SRv6 service can fall back to any SRv6 shortest path tunnel in TTMv6 or RTM, if the locator of the tunnel matches the locator of the SRv6 service.

Use the resolution command in the following contexts to configure the resolution options:

S-BFD and end-to-end protection, using Linear or ECMP protection modes, are supported for static and BGP SRv6 policies. To configure S-BFD and, optionally, a protection mode, apply a maintenance policy to a static or BGP SRv6 policy. The router attempts to establish an S-BFD session on each segment list of the SRv6 policy.

See Seamless BFD and end-to-end protection for SR policies for information about how to configure S-BFD and protection. S-BFD with a routed return path and S-BFD with a controlled return path are supported. In routed return path, the S-BFD reply packet is sent using a routed path from the reflector. In controlled return path, the S-BFD packet is returned to the initiator via a specified traffic engineered path such as an SRv6 Policy.

In routed return path, S-BFD packets are encapsulated in the SRv6 policy packet using a segment routing header which includes a SID containing the endpoint address of the SRv6 policy as the last SID of the header. The following figure shows S-BFD encapsulation over an SRv6 policy with routed return path.

In controlled return path, a SID specified at the initiator router is also inserted in the SRH for S-BFD packets. This SID refers to a binding SID on an SRv6 policy configured at the far-end of the S-BFD session (usually the endpoint of the SRv6 policy). Echo mode is also used for the S-BFD session. The following figure shows S-BFD encapsulation over an SRv6 policy with controlled return path.

SRv6 policies support egress statistics similar to SR MPLS policies. See Traffic statistics, Segment routing with MPLS data plane (SR-MPLS), and Segment routing policies.

SRv6 policies do not support ingress statistics.

Traffic statistics related commands that are defined in the following context affect both SRv6 and segment routing MPLS policies. It is not possible to enable or disable statistics for only one type of policy.

configure router segment-routing sr-policies

SRv6 policies support micro-segment SRv6. With the seamless introduction of micro-segment SRv6 , the term SRv6 policy now refers to policies using regular (128-bit) SIDs or uSIDs (16-bit), or a combination of both.

All services supported on SRv6 policies before the introduction of micro-segment support continue to be supported. The same applies to applications interacting with SRv6 policies: maintenance policies, sBFD, OAM, PBR, and traffic statistics.

When assigning an IPv6 address from a classic SRv6 locator, the feature reserves the least significant octet of the locator subnet for IPv6 address of system and loopback interfaces. This is the main subnet of the locator with bits to the right of the node ID set to zero, except for the interface bits.

The following is an example of the address assignment.

This feature supports a mask value of /128 only. A maximum of 255 addresses can be allocated from the last octet of the locator. A value of zero for that octet represents the identifier of the entire subnet and is not allocatable.

When assigning an IPv6 address from a micro-segment SRv6 locator, the feature reserves the least significant octet of the micro-segment locator subnet for IPv6 address of system and loopback interfaces. This is the main subnet of the locator with bits to the right of the uN set to zero, except the interface bits.

The following is an example of the address assignment.

• locator subnet: fc00:0:105::/48
• locator subnet identifier: fc00:0:105:0:0:0:0:0
• system/loopback interface addresses allowed are: fc00:0:105:0:0:0:0:00[01-FF]/128

This feature supports a mask value of /128 only. A maximum of 255 addresses can be allocated from the last octet of the locator. A value of zero for that octet represents the identifier of the entire subnet and is not allocatable.