s Commands – Part II
session-filter
session-filter
Syntax
session-filter
session-filter session-filter-name
Context
[Tree] (show>app-assure>group session-filter)
Full Context
show application-assurance group session-filter
Description
This command displays session filter information.
Parameters
- session-filter-name
-
Specifies a session-filter-name up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the session-filter command information.
Output Exampleshow application-assurance group <aa-group-id>[:<partition>] session-filter <filter-
name>
# session-filter<filter-id>
========================================================================
AA Session Filter
========================================================================
Filter Name : Block UDP Session Initiation
Applied : Yes Def. Action : Permit
Entries : 1
Description : Block UDP initiated towards subscribers
------------------------------------------------------------------------
Filter Match Criteria
------------------------------------------------------------------------
Entry : 1
Description : (Not Specified)
Protocol : 17
Action : deny
Hit Count : 0 pkts
========================================================================
session-parameters
session-parameters
Syntax
session-parameters [family] [community community]
session-parameters peer-ip-address
Context
[Tree] (show>router>ldp session-parameters)
Full Context
show router ldp session-parameters
Description
This command displays LDP peer information.
Parameters
- peer-ip-address
-
Specify the peer IP address.
- family
-
Displays either IPv4 or IPv6 active LDP information.
- community
-
The string defining the LDP community assigned to the session. Allowed values are any string up to 32 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
Output
Output fields: LDP session parameters describes the LDP session-parameters output.
|
Label |
Description |
|---|---|
|
Peer |
The IP address of the peer. |
|
TTL security |
Enabled — LDP peering sessions protected. Disabled — LDP peering sessions unprotected. |
|
Min-TTL-Value |
Displays the minimum TTL value for an incoming packet. |
|
Auth |
Enabled — Authentication using MD5 message based digest protocol is enabled. Disabled — No authentication is used. |
Example with community RED:
*A:SRU4# show router ldp session-parameters 10.20.1.1
===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.20.1.1
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise : Enabled
Community : RED
===============================================================================
No. of IPv4 Peers: 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
Example without community
*A:Dut-A# show router ldp session-parameters
===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.20.1.2
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.3
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.6
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv4 Peers: 3
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
LDP IPv6 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 3ffe::a14:102
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Disabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 3ffe::a14:103
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Disabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv6 Peers: 2
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
*A:Dut-A# show router ldp session-parameters 3ffe::a14:103
===============================================================================
LDP IPv6 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 3ffe::a14:103
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Disabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv6 Peers: 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
*A:Dut-A# show router ldp session-parameters ipv4
===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.20.1.2
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.3
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.6
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv4 Peers: 3
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
session-tokens
session-tokens
Syntax
session-tokens
Context
[Tree] (tools>dump>sys>sec>support-mode session-tokens)
Full Context
tools dump system security support-mode session-tokens
Description
This command displays the current shell and kernel session tokens on the system.
Platforms
7750 SR-1, 7750 SR-s, 7950 XRS-20e
Output
The following output is an example of session token information.
Output exampleA:node-2>tools>dump>sys>sec>support-mode# session-tokens
No tokens in current session for shell
No tokens in current session for kernel
A:node-2>tools>dump>sys>sec>support-mode#
sessions
sessions
Syntax
sessions [group name] neighbor ip-address] [port port-number] [association] [ statistics]
Context
[Tree] (show>service>id>gsmp sessions)
Full Context
show service id gsmp sessions
Description
This command displays GSMP sessions information.
Parameters
- group
-
A GSMP group defines a set of GSMP neighbors which have the same properties.
- name
-
Specifies a GSMP group name is unique only within the scope of the service in which it is defined.
- ip-address
-
Specifies the ip-address of the neighbor.
- port
-
Specifies the neighbor TCP port number use for this ANCP session.
- association
-
Displays to what object the ANCP-string is associated.
- statistics
-
Displays statistics information about an ANCP session known to the system.
Platforms
All
Output
The following output is an example of GSMP sessions information.
Output ExampleThis show command gives information about the open TCP connections with DSLAMs.
A:active>show>service>id>gsmp# sessions
=======================================================
GSMP sessions for service 999 (VPRN)
=======================================================
Port Ngbr-IpAddr Gsmp-Group
-------------------------------------------------------
40590 192.168.1.2 dslam1
-------------------------------------------------------
Number of GSMP sessions : 1
=======================================================
A:active>show>service>id>gsmp#
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590
=========================================================================
GSMP sessions for service 999 (VPRN), neighbor 192.168.1.2, Port 40590
=========================================================================
State : Established
Peer Instance : 1 Sender Instance : a3cf58
Peer Port : 0 Sender Port : 0
Peer Name : 12:12:12:12:12:12 Sender Name : 00:00:00:00:00:00
timeouts : 0 Max. Timeouts : 3
Peer Timer : 100 Sender Timer : 100
Capabilities : DTD OAM
Conf Capabilities : DTD OAM
Priority Marking : dscp nc2
Local Addr. : 192.168.1.4
Conf Local Addr. : N/A
=========================================================================
A:active>show>service>id>gsmp#
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 association
===============================================================================
ANCP-Strings
===============================================================================
ANCP-String Assoc. State
-------------------------------------------------------------------------------
No ANCP-Strings found
===============================================================================
A:active>show>service>id>gsmp#
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 statistics
===============================================================
GSMP session stats, service 999 (VPRN), neighbor 192.168.1.2, Port 40590
===============================================================
Event Received Transmitted
---------------------------------------------------------------
Dropped 0 0
Syn 1 1
Syn Ack 1 1
Ack 14 14
Rst Ack 0 0
Port Up 0 0
Port Down 0 0
OAM Loopback 0 0
===============================================================
A:active>show>service>id>gsmp#
The following table describes service ID GSMP sessions output fields:
|
Label |
Description |
|---|---|
|
Port |
The port ID number |
|
Ngbr-IpAddr |
The neighbor IP address |
|
Gsmp-Group |
The GSMP group ID |
|
State |
The GSMP state of this TCP connection |
|
Peer Instance |
The unique GSMP ID for each end of the GSMP connection |
|
Peer Port |
The unique GSMP ID for each end of the GSMP connection |
|
Peer Name |
The unique GSMP ID for each end of the GSMP connection |
|
timeouts |
The number of successive timeouts for this session |
|
Peer Timer |
The GSMP keepalive timer |
|
Capabilities |
The ANCP capabilities negotiated for this session |
|
Conf Capabilities |
The ANCP capabilities configured for this session |
|
Priority Marking |
The priority marking configured for this session |
|
Local Addr |
The IP address used by the box's side of the TCP connection |
|
Conf. Local Addr. |
The configured IP address used by the box's side of the TCP connection |
|
Sender Instance |
The instance sent to the neighbor in this session |
|
Sender Port |
The port sent to the neighbor in this session |
|
Sender Name |
The name sent to the neighbor in this session |
|
Max. Timeouts |
The maximum number of successive timeouts configured for this session |
|
Sender Timer |
The timeout value that is announced toward the neighbor. The neighbor uses this timeout value while waiting for an acknowledgment from this system. |
The association command gives an overview of each ANCP string received from this session.
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 association
===============================================================================
ANCP-Strings
===============================================================================
ANCP-String Assoc.
State
-------------------------------------------------------------------------------
7330-ISAM-E47 atm 1/1/01/01:19425.64048 ANCP Up
-------------------------------------------------------------------------------
Number of ANCP-Strings : 1
===============================================================================
A:active>show>service>id>gsmp
sessions
Syntax
sessions [nat-group nat-group-id] [ mda mda-id] [protocol { gre | icmp | icmp6 | tcp | udp | unknown}] [inside-ip ip-prefix[/ ip-prefix-length]] [inside-router router-instance] [inside-port port-number] [ outside-ip ipv4-address] [outside-port port-number] [foreign-ip ip-address] [foreign-port port-number] [ dslite-address ipv6-address] [wlan-gw-ue ieee-address] [next-index index] [upnp] [ member member-id] [nat-policy policy-name] [dest-ip ip-address] [firewall-policy policy-name] [ address-type addr-type] [l2-aware-subscriber sub-ident]
Context
[Tree] (tools>dump>nat sessions)
Full Context
tools dump nat sessions
Description
This command dumps ISA sessions.
Parameters
- icmp
-
Specifies to dump only ICMP information.
- ieee-address
-
Specifies a MAC address, using the format xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
- ip-address
-
Specifies an IPv4 or IPv6 address.
- ipv4-address
-
Specifies an IPv4 address.
- ipv6-address
-
Specifies an IPv6 address.
- mda-id
-
Specifies an MDA ID.
- nat-group-id
-
Specifies a NAT group ID.
- policy-name
-
Specifies a policy name, up to 32 characters maximum.
- port-number
-
Specifies a port number.
- router-instance
-
Specifies a router name or service ID.
- tcp
-
Specifies to dump only TCP information.
- udp
-
Specifies to dump only UDP information.
- upnp
-
Specifies to dump only UPNP information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of this command.
Output Example*A:SR12_PPPOE# tools dump nat sessions
===============================================================================
Matched 2 sessions on Slot #3 MDA #1
===============================================================================
Owner : LSN-Host@10.2.3.4
Router : 100
FlowType : UDP PortFwd
Inside IP Addr : 10.2.3.4 Inside Port : 666
Outside IP Addr : 10.0.0.6 Outside Port : 666
Foreign IP Addr : * Foreign Port : *
Dest IP Addr : * Dest Port : *
-------------------------------------------------------------------------------
Owner : LSN-Host@10.2.3.4
Router : 100
FlowType : TCP PortFwd
Inside IP Addr : 10.2.3.4 Inside Port : 666
Outside IP Addr : 10.0.0.6 Outside Port : 666
Foreign IP Addr : * Foreign Port : *
Dest IP Addr : * Dest Port : *
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
Matched 1 session on Slot #3 MDA #2
===============================================================================
Owner : LSN-Host@2001:db8:470:1F00:FFFF:189
Router : 100
FlowType : TCP Timeout (sec) : 6769
Inside IP Addr : 192.168.16.218 Inside Port : 41555
Outside IP Addr : 10.0.0.5 Outside Port : 1529
Foreign IP Addr : 10.0.0.1 Foreign Port : 22
Dest IP Addr : 10.0.0.1 Dest Port : 22
-------------------------------------------------------------------------------
===============================================================================
*A:SR12_PPPOE#
sessions
Syntax
sessions [test-family {ethernet | ip | mpls}]
sessions [test-family {ethernet | ip | mpls}] detectable-rx-errors
sessions [test-family {ethernet | ip | mpls}] detectable-tx-errors
sessions [test-family {ethernet | ip | mpls}] event-mon
sessions [test-family {ethernet | ip | mpls}] streaming delay
Context
[Tree] (show>oam-pm sessions)
Full Context
show oam-pm sessions
Description
This command shows a summary of the OAM Performance Monitoring sessions.
Parameters
- test-family
-
Shows all sessions that match the specified test family type when an optional filter is included.
- ethernet
-
Specifies Ethernet session types.
- ip
-
Specifies IP session types.
- mpls
-
Specifies MPLS session types.
- event-mon
-
Specifies a summary of all event monitoring and current state for each session.
- detectable-rx-errors
-
Specifies to display all MPLS sessions with a reported non-successful return code. The results of all return codes, other than "success”, are included. When a return code is not available it is reported as "none”. Sessions with a successful return code are filtered and not displayed in the list. This is specific to test-family mpls only.
- detectable-tx-errors
-
Specifies to provide a summary of tests with detectable transmission errors that prevent the test from sending packets. Not all errors are detectable.
- streaming delay
-
Displays all sessions with an assigned delay template.
Platforms
All
Output
The following output is an example of OAM-PM session summary information.
Output Exampleshow oam-pm sessions
============================================================================
OAM Performance Monitoring Session Summary for the Ethernet Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
vpls1000-PM-AL5-1/1/9:1000.1000 Act 2 proactive DMM SLM
vpls1000-PM-YL4-1/1/9:1000.1000 Act 3 proactive DMM SLM
============================================================================
============================================================================
OAM Performance Monitoring Session Summary for the IP Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
============================================================================
============================================================================
OAM Performance Monitoring Session Summary for the MPLS Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
mpls-dm-static-31-28 Act 2 proactive DM
mpls-dm-rsvp-31-to-28 Act 2 proactive DM
mpls-dm-rsvp-auto-31-to-28 Act 2 proactive DM
============================================================================
show oam-pm sessions event-mon
===============================================================================
OAM Performance Monitoring Event Summary for the Ethernet Test Family
===============================================================================
Event Monitoring Table Legend:
F = Forward, B = Backward, R = Round Trip, A = Aggregate,
- = Threshold Not Config, c = Threshold Config, * = TCA Active, P = Pending
===============================================================================
Test FD FDR IFDV FLR CHLI HLI UNAV UDAV UDUN
Session Type FBR FBR FBR FB FBA FBA FBA FBA FBA
-------------------------------------------------------------------------------
vpls1000-PM-AL5-1/1/9:1000.1000 DMM --- --- ---
vpls1000-PM-AL5-1/1/9:1000.1000 SLM -- --- --- --- --- ---
vpls1000-PM-YL4-1/1/9:1000.1000 DMM --c --- ---
vpls1000-PM-YL4-1/1/9:1000.1000 SLM -- --- --- --- --- ---
===============================================================================
===============================================================================
OAM Performance Monitoring Event Summary for the IP Test Family
===============================================================================
Event Monitoring Table Legend:
F = Forward, B = Backward, R = Round Trip, A = Aggregate,
- = Threshold Not Config, c = Threshold Config, * = TCA Active, P = Pending
===============================================================================
Test FD FDR IFDV FLR CHLI HLI UNAV UDAV UDUN
Session Type FBR FBR FBR FB FBA FBA FBA FBA FBA
-------------------------------------------------------------------------------
===============================================================================
show oam-pm sessions detectable-rx-errors
===============================================================================
OAM Performance Monitoring Receive Error Summary: MPLS Test Family
===============================================================================
Test
Session Type MPLS DM Receive Status
-------------------------------------------------------------------------------
S0 DM unexpected MPLS test Rx status code
S2 DM Notify: Data Format Invalid
S3 DM Notify: Initialization in Progress
S4 DM Notify: Data Reset Occurred
S5 DM Notify: Resource Temporarily Unavail
S6 DM unexpected MPLS test Rx status code
S16 DM Error: Unspecified Error
S17 DM Error: Unsupported Version
S18 DM Error: Unsupported Control Code
S19 DM Error: Unsupported Data Format
S20 DM Error: Authentication Failure
S21 DM Error: Invalid Destination Node Id
S22 DM Error: Connection Mismatch
S23 DM Error: Unsupported Mand TLV Object
S24 DM Error: Unsupported Query Interval
S25 DM Error: Administrative Block
S26 DM Error: Resource Unavailable
S27 DM Error: Resource Released
S28 DM Error: Invalid Message
S29 DM Error: Protocol Error
S30 DM unexpected MPLS test Rx status code
S256 DM none
S257 DM Error: Timeout
S258 DM unexpected MPLS test Rx status code
===============================================================================
show oam-pm sessions detectable-tx-errors
===============================================================================
OAM Performance Monitoring Transmit Error Summary: Ethernet Test Family
===============================================================================
Test
Session Type Detectable Transmit Error
-------------------------------------------------------------------------------
vpls1000-PM-YL4-1/1/9:1000.1000 DMM MEP is administratively down
vpls1000-PM-YL4-1/1/9:1000.1000 SLM MEP is administratively down
===============================================================================
===============================================================================
OAM Performance Monitoring Transmit Error Summary: IP Test Family
===============================================================================
Test
Session Type Detectable Transmit Error
-------------------------------------------------------------------------------
===============================================================================
show oam-pm sessions streaming delay
===============================================================================
OAM-PM Streaming Delay Summary for the Ethernet Test Family
===============================================================================
Session Test Type Test State Str Template Admin
-------------------------------------------------------------------------------
eth-circuit-service-epipe1 DMM Inact Up
===============================================================================
===============================================================================
OAM-PM Streaming Delay Summary for the IP Test Family
===============================================================================
Session Test Type Test State Str Template Admin
-------------------------------------------------------------------------------
ip-lpb111-SR-TE-LSP TWL Act Up
ip-circuit-service-vprn2 TWL Act Up
ip-rtr-telemetry-streaming TWL Act Up
===============================================================================
===============================================================================
OAM-PM Streaming Delay Summary for the MPLS Test Family
===============================================================================
Session Test Type Test State Str Template Admin
-------------------------------------------------------------------------------
mpls-dm-rsvp-PE-2-PE-1 DM Act Up
mpls-dm-static-PE-2-PE-1 DM Act Up
mpls-dm-rsvp-PE-2-PE-1-hop1 DM Act Up
mpls-dm-rsvp-auto-PE-2-PE-1 DM Act Template Not Found
===============================================================================
set-epoch-value
set-epoch-value
Syntax
set-epoch-value value
Context
[Tree] (tools>perform>router>pcp-server set-epoch-value)
Full Context
tools perform router pcp-server set-epoch-value
Description
This command sets the epoch value for a specified PCP server.
Parameters
- value
-
Specifies the epoch value.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
set-fabric-speed
set-fabric-speed
Syntax
set-fabric-speed fabric-speed
Context
[Tree] (tools>perform>system set-fabric-speed)
Full Context
tools perform system set-fabric-speed
Description
This command configures the fabric speed. This command is necessary to define the mode of operation for the system.
Default
set-fabric-speed none (for the 7750 SR-7s/14s FP4 and 7950 XRS systems)
set-fabric-speed fabric-speed-d (or the 7750 SR-7s/14s FP5 systems)
set-fabric-speed fabric-speed-a (for the other 7750 SR and 7450 ESS systems)
Parameters
- fabric-speed
-
Specifies the fabric speed of the system.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-7s, 7750 SR-14s, 7950 XRS
set-role
set-role
Syntax
set-role {extension | master | standalone}
Context
[Tree] (tools>perform>chassis set-role)
Full Context
tools perform chassis set-role
Description
This command sets the role of the 7950 XRS chassis from which the command is invoked.
-
When run on a standalone chassis this will update the EEPROM on the (one) Chassis backplane.
-
Master and Extension chassis are blocked if any SFMs are configured as type sfm-x20 (must be sfm-x20-b). The following message displays:
-
When the extension option is specified, the chassis will immediately reboot as part of the command. The following warning and prompt will be provided:
WARNING: You are about to provision the chassis as an XRS-40 Extension chassis. This chassis will immediately reboot after the command is executed. No CLI shell is available directly on an Extension chassis. An Extension chassis will not completely boot up unless it is properly cabled to and controlled by an XRS-40 Master chassis. Do you wish to proceed (yes/no) ? -
When the master option is specified, the chassis will immediately reboot as part of the command. The Operational mode is not changed until a reboot is performed. The following warning and prompt will be provided:
WARNING: You are about to provision the chassis as an XRS- 40 Master chassis. This chassis will immediately reboot after the command is execute Do you wish to proceed (yes/no) ? -
When the master or extension options are specified and the chassis has any SFM slots with a configured type of sfm-x20, then the command will fail with the following message:
Configured sfm-type of sfm-x20 is not compatible with XRS-40 mode operation.If you want to change the role of the chassis anyways, you can deconfigure the SFMs and then change the role.
Platforms
7950 XRS
set-trim-mode
set-trim-mode
Syntax
set-trim-mode set-trim-mode
Context
[Tree] (tools>perform>system set-trim-mode)
Full Context
tools perform system set-trim-mode
Description
This command should only be used with authorized direction of Nokia technical support.
Parameters
- set-trim-mode
-
Specifies the trim operating mode for the system.
Platforms
7450 ESS, 7750 SR-7/12/12e
sflow
sflow
Syntax
sflow
Context
[Tree] (show sflow)
Full Context
show sflow
Description
This command displays the primary and backup receiver statistics, the mapping configuration and a summary of how many ports and SAPs have sFlow enabled.
Platforms
7750 SR, 7750 SR-s, 7950 XRS
Output
The following output is an example of sFlow information. Output fields: sFlow describes the show sFlow output fields.
Output Example*B:bkvm10# show sflow
===============================================================================
sFlow Status
===============================================================================
Receiver : pat
Max Data Size : 312
IP Addr Primary : 10.120.142.163:6343
Packets Sent : 2572
Packet Errors : 2
Last Packet Sent : 07/08/2014 22:23:57nt
IP Addr Backup : N/A
Packets Sent : 0
Packet Errors : 0
Last Packet Sent : No Pkts sent
-----------------------------------
Counter Pollers
-----------------------------------
Port No. of SAPs
-----------------------------------
1/1/2 3
1/2/1 0
-----------------------------------
No. of sFlow counter pollers: 2
-----------------------------------
--------------------------------------------------
Counter Mappings
--------------------------------------------------
Direction Policer/Queue Traffic Type
--------------------------------------------------
egress queue 1 unicast
egress queue 5 multicast
egress queue 8 broadcast
ingress policer 1 unicast
ingress policer 6 multicast
ingress policer 12 broadcast
--------------------------------------------------
No. of sFlow counter mappings: 6
--------------------------------------------------
===============================================================================
|
Label |
Description |
|---|---|
|
sFlow Status |
|
|
Receiver |
Displays the configured name for the sFlow receiver. |
|
Max Data Size |
The configured maximum data size for sFlow UDP packets. |
|
IP Addr Primary |
The primary IP address and destination port for sFlow receiver. |
|
IP Addr Backup |
The backup IP address and destination port for sFlow receiver. |
|
Packets Sent |
The number of packets sent successfully to the primary or backup receiver destination, since the destination was configured, CPM card HA switchover, or system reboot. |
|
Packet Errors |
The number of packets that could not be sent to the primary or backup receiver destination because of an error, since the destination was configured, CPM card HA switchover, or system reboot. An example of an error is destination IP not reachable. |
|
Last Packet Sent |
Displays the date and time of the last packet sent. |
|
Counter Pollers |
|
|
Port |
Displays the port on which sFlow is enabled. |
|
No. of SAPs |
The number of SAPs on the port with sFlow enabled. |
|
No. of sFlow counter pollers |
The number of sFlow counter pollers. |
|
Counter Mappings |
|
|
Direction |
Displays the direction of traffic (ingress or egress) the map entry applies to. |
|
Policer/Queue |
Displays the policer or queue instance being mapped by sFlow map. |
|
Traffic type |
Displays the type of sFlow traffic statistics (unicast, multicast or broadcast) that the policer/queue maps to. |
|
No. of sFlow counter mappings |
The number of entries in the sFlow ingress and egress counter map. |
sfm
sfm
Syntax
sfm sfm-name [force]
Context
[Tree] (clear sfm)
Full Context
clear sfm
Description
This command resets the SFM.
Parameters
- sfm-name
-
Specifies the SFM identifier.
- force
-
Performs the reset without a confirmation prompt.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-2s, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, 7950 XRS
sfm
Syntax
sfm [sfm-name] [detail]
sfm [sfm-name] icport [down] [ degraded]
Context
[Tree] (show sfm)
Full Context
show sfm
Description
This command displays SFM status information.
Parameters
- sfm-name
-
Specifies the SFM identifier.
- icport
-
Displays interconnect port information.
- down
-
Displays interconnect ports that are not operational.
- degraded
-
Displays interconnect ports that are associated with fabric degradation.
- detail
-
Displays detailed information about the SFM.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-2s, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, 7950 XRS
Output
See the following output examples:
A:7950 XRS-20# show sfm
===============================================================================
SFM Summary
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
1 sfm-x20 up up
2 sfm-x20 up up
3 sfm-x20 up up
4 sfm-x20 up up
5 sfm-x20 up up
6 (not provisioned) up unprovisioned
sfm-x20
7 (not provisioned) up unprovisioned
sfm-x20
8 (not provisioned) up unprovisioned
sfm-x20
===============================================================================
A:7950 XRS-20# show sfm 2 detail
===============================================================================
Fabric 2
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
2 (not provisioned) up unprovisioned
sfm-x20
Hardware Data
Part number : xx
CLEI code : xx
Serial number : xx
Manufacture date : xx
Manufacturing string : xx
Manufacturing deviations : xx
Manufacturing assembly number : xx
Administrative state : up
Operational state : unprovisioned
Time of last boot : N/A
Current alarm state : alarm cleared
===============================================================================
Inter Chassis SFM Interconnect
SFM Interconnect Port 1
oper state : no-link
Misconnect Info : Fabric 3 IcPort 14
SFF Status : not-equipped
fabric degrade state : none
*A:myNode# show sfm icport
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFMSFM IcPort IcPort Module Degrade Miscon.Info
Oper State Num Oper State Inserted State SFM IcPort
-------------------------------------------------------------------------------
1 unprovisioned 1 up yes none
1 unprovisioned 2 invalid-conne* no degraded 3 14
2 up 2 indeterminate no none
2 up 3 up no degraded
2 up 5 no-link no none
2 up 14 indeterminate yes degraded
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
*A:myNode# show sfm icport down
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFM SFM IcPortIcPortModuleDegradeMiscon. Info
Oper StateNumOper StateInsertedStateSFMIcPort
-------------------------------------------------------------------------------
1 unprovisioned 2invalid-conne*nodegraded 3 14
2 up 2indeterminatenonone
2 up5no-linknonone
2 up14indeterminateyesdegraded
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:myNode# show sfm icport degraded
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFM SFMIcPortIcPortModuleDegradeMiscon. Info
Oper StateNumOper StateInserted State SFM IcPort
-------------------------------------------------------------------------------
2 up 3 up no degraded
2 up 14 indeterminate yes degraded
===============================================================================
Output fields: SFM describes output fields for the show sfm command.
|
Label |
Description |
|---|---|
|
Slot |
The number of the slot in which the SFM is installed. |
|
Provisioned Type Equipped Type (if different) |
The SFM type provisioned. |
|
Admin State |
The administrative state. |
|
Operational State |
The operational state. |
|
Hardware Data |
|
|
Part number |
The SFM part number. |
|
CLEI code |
The SFM CLEI code. |
|
Serial number |
The SFM serial number. |
|
Manufacture date |
The date the SFM was manufactured. |
|
Manufacturing deviations |
Specifies any manufacturing deviations. |
|
Manufacturing assembly number |
The SFM assembly number. |
|
Administrative state |
Specifies the administrative state of the SFM. |
|
Operational state |
Specifies the operational state of the SFM. |
|
Time of last boot |
Indicates the time stamp of the last system restart. |
|
Current alarm state |
Indicates the current alarm state. |
|
Inter Chassis SFM Interconnect |
|
|
SFM Interconnect Port |
Port number of the interconnect port. |
|
oper state |
Up — The SFM is administratively up. Down — The SFM is administratively down. |
|
Misconnect Info |
Only displayed if the oper state is invalid-connection. |
|
SFF Status |
The SFF status |
|
fabric degrade state |
Indicates state. |
sfm-interco-test
sfm-interco-test
Syntax
sfm-interco-test [sfm x]
Context
[Tree] (tools>perform>system>inter-chassis sfm-interco-test)
Full Context
tools perform system inter-chassis sfm-interco-test
Description
Use this command to run inter-chassis SFM loopback tests for the 7950 XRS.
Run on an out-of-service standalone chassis that will later become the Extension chassis of an XRS-40 system. The out of service chassis (Chassis 1 – future Master chassis) must be connected by means of SFM interconnect links (cable bundles) before this test is run. This test operates without requiring any XCMs in either chassis, but they can be present.
The test should not be initiated from Chassis 1.
The following conditions must be satisfied for the test to be permitted:
-
The system must be in standalone mode; error message:
The test can only be performed on a standalone system
-
The system must have only XRS-40 compatible SFMs provisioned; error message:
The chassis can not have SFMs with a configured type of sfm-x20s-b
when performing the test
-
All provisioned SFMs must be operational; error message:
All provisioned SFMs must be operational before performing the test
-
The same test cannot be running in another session (that is, only one test can be executed at a time); error message:
The test is already in-progress in another session
Other notes (which are also relayed to the operator when the test is attempted):
-
All provisioned XCMs will be reset at the start of the test and will be held in the booting state until the test has completed.
-
All SFMs will be cleared when the operator exits the test. This will trigger a reset of the XCMs and the standby CPM.
Platforms
7950 XRS
Output
The following output is an example of SFM interconnection test information.
Output Example*A:Dut-A# tools perform system inter-chassis sfm-interco-test
WARNING: This test is intended for an out-of-service standalone chassis that is
going to later become the extension chassis of an XRS-40 system.
At the start of the test, all provisioned IOMs will be reset and will be held
in the 'booting' state until the test has completed.
While the test is running avoid altering this system or the attached system
(e.g. do not shutdown, clear, or remove the CPMs/SFMs/IOMs and do not issue
CPM switchovers)
Once testing has completed all SFMs in this system will be cleared.
Do you wish to proceed (y/n)? y
Clearing provisioned IOMs ...
Test executing ...
Displaying results
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFM SFM IcPort IcPort Module Degrade Miscon Info
Oper State Num Oper State Inserted State SFM IcPort
-------------------------------------------------------------------------------
1 up 1 up yes none
1 up 2 up yes none
1 up 3 up yes none
1 up 4 up yes none
1 up 5 up yes none
1 up 6 up yes none
1 up 7 up yes none
1 up 8 up yes none
1 up 9 up yes none
1 up 10 up yes none
1 up 11 up yes none
1 up 12 up yes none
1 up 13 up yes none
1 up 14 up yes none
2 up 1 up yes none
2 up 2 up yes none
2 up 3 up yes none
2 up 4 up yes none
2 up 5 up yes none
2 up 6 up yes none
2 up 7 up yes none
2 up 8 up yes none
2 up 9 up yes none
2 up 10 up yes none
2 up 11 up yes none
2 up 12 up yes none
2 up 13 up yes none
2 up 14 up yes none
3 up 1 up yes none
3 up 2 up yes none
3 up 3 up yes none
3 up 4 up yes none
3 up 5 up yes none
3 up 6 up yes none
3 up 7 up yes none
3 up 8 up yes none
3 up 9 up yes none
3 up 10 up yes none
3 up 11 up yes none
3 up 12 up yes none
3 up 13 up yes none
3 up 14 up yes none
4 up 1 up yes none
4 up 2 up yes none
4 up 3 up yes none
4 up 4 up yes none
4 up 5 up yes none
4 up 6 up yes none
4 up 7 up yes none
4 up 8 up yes none
4 up 9 up yes none
4 up 10 up yes none
4 up 11 up yes none
4 up 12 up yes none
4 up 13 up yes none
4 up 14 up yes none
5 up 1 up yes none
5 up 2 up yes none
5 up 3 up yes none
5 up 4 up yes none
5 up 5 up yes none
5 up 6 up yes none
5 up 7 up yes none
5 up 8 up yes none
5 up 9 up yes none
5 up 10 up yes none
5 up 11 up yes none
5 up 12 up yes none
5 up 13 up yes none
5 up 14 up yes none
6 up 1 up yes none
6 up 2 up yes none
6 up 3 up yes none
6 up 4 up yes none
6 up 5 up yes none
6 up 6 up yes none
6 up 7 up yes none
6 up 8 up yes none
6 up 9 up yes none
6 up 10 up yes none
6 up 11 up yes none
6 up 12 up yes none
6 up 13 up yes none
6 up 14 up yes none
7 up 1 up yes none
7 up 2 up yes none
7 up 3 up yes none
7 up 4 up yes none
7 up 5 up yes none
7 up 6 up yes none
7 up 7 up yes none
7 up 8 up yes none
7 up 9 up yes none
7 up 10 up yes none
7 up 11 up yes none
7 up 12 up yes none
7 up 13 up yes none
7 up 14 up yes none
8 up 1 up yes none
8 up 2 up yes none
8 up 3 up yes none
8 up 4 up yes none
8 up 5 up yes none
8 up 6 up yes none
8 up 7 up yes none
8 up 8 up yes none
8 up 9 up yes none
8 up 10 up yes none
8 up 11 up yes none
8 up 12 up yes none
8 up 13 up yes none
8 up 14 up yes none
===============================================================================
Correct any mis-cabling and replace any suspected faulty equipment. Press Q to
quit the test or any other key to run the test again. q
Test complete, clearing the SFMs to return them to normal operational state.
Done. Exiting test.
sgt-qos
sgt-qos
Syntax
sgt-qos
Context
[Tree] (show>router sgt-qos)
Full Context
show router sgt-qos
Description
This command displays QoS information for self-generated traffic. In the output, "none” means that the default values for each application are used, not that there is no value set. For a list of application defaults, refer to "QoS for Self-Generated (CPU) Traffic on Network Interfaces” in the 7450 ESS, 7750 SR, 7950 XRS, and VSR Quality of Service Guide.
Platforms
All
sham-link
sham-link
Syntax
sham-link [interface-name] [detail]
sham-link interface-name remote ip-address [detail]
Context
[Tree] (show>router>ospf sham-link)
Full Context
show router ospf sham-link
Description
This command displays OSPFv2 sham-link neighbor information.
Parameters
- interface-name
-
Displays only the sham link identified by this interface name, up to 32 characters.
- remote
-
Displays sham-link information for the sham link identified by the specified remote IP address.
- ip-address
-
Displays only the sham link identified by this IP address.
Platforms
All
Output
The following output is an example of OSPFv2 sham-link neighbor information and Output fields: OSPF sham links describes the output fields.
Output Exampleshow router 1 ospf sham-link detail
===============================================================================
Rtr vprn1 OSPFv2 Instance 0 Sham-Links (detail)
===============================================================================
-------------------------------------------------------------------------------
Interface: myshamif1 Remote Nbr: 50.0.1.2
-------------------------------------------------------------------------------
Local IP Address : 50.0.1.1
Area Id : 0.0.0.0 Last Enabled : 08/12/2021 13:09:05
Admin Status : Enabled Oper State : Point To Point
Transit Delay : 1 sec Retrans Intrvl : 5 sec
Hello Intrvl : 1 sec Rtr Dead Intrvl : 3 sec
Cfg Metric : 10 Auth Type : None
If Events : 1
Tot Rx Packets : 0 Tot Tx Packets : 32
Rx Hellos : 0 Tx Hellos : 32
Rx DBDs : 0 Tx DBDs : 0
Rx LSRs : 0 Tx LSRs : 0
Rx LSUs : 0 Tx LSUs : 0
Rx LS Acks : 0 Tx LS Acks : 0
Discards : 0 Tx Failures : 0
Retransmits : 0
Bad Networks : 0
Bad Areas : 0 Bad Dest Addrs : 0
Bad Auth Types : 0 Auth Failures : 0
Bad Neighbors : 0 Bad Pkt Types : 0
Bad Lengths : 0 Bad Hello Int. : 0
Bad Dead Int. : 0 Bad Options : 0
Bad Versions : 0 Bad Checksums : 0
===============================================================================
|
Label |
Description |
|---|---|
|
If Name |
IP interface name |
|
Nbr IP |
IP address of the neighbor |
|
Metric |
The metric associated with the interface |
|
Adm |
The administrative state of the interface |
|
Oper |
The operational state of the interface |
|
No. of OSPF Sham-links |
Number of sham links configured |
|
Tx Failures |
Transmitted OSPF packets that are dropped due to resource shortage |
sham-link-neighbor
sham-link-neighbor
Syntax
sham-link-neighbor [detail]
sham-link-neighbor interface-name remote ip-address [detail]
Context
[Tree] (show>router>ospf sham-link-neighbor)
Full Context
show router ospf sham-link-neighbor
Description
This command displays OSPFv2 sham-link neighbor information.
Parameters
- interface-name
-
Displays only the sham-link neighbor identified by this interface name, up to 32 characters.
- remote
-
Displays sham-link neighbor information for the neighbor identified by the specified remote IP address.
- ip-address
-
Displays only the sham-link neighbor identified by this IP address.
Platforms
All
shared-queue
shared-queue
Syntax
shared-queue [shared-queue-policy-name] [detail]
Context
[Tree] (show>qos shared-queue)
Full Context
show qos shared-queue
Description
This command displays shared-queue policy information.
Parameters
- shared-queue-policy-name
-
The shared-queue policy name.
- detail
-
Displays detailed information about the shared-queue policy.
Platforms
All
Output
The following output is an example of shared-queue QoS policy information, and Output fields: QoS shared queue describes shared-queue QoS policy output fields.
Output Example*A:PE# show qos shared-queue
===============================================================================
Shared Queue Policies
===============================================================================
Policy-Id Description
-------------------------------------------------------------------------------
default Default Shared Queue Policy
policer-output-queues Default Policer Output Shared Queue Policy
egress-pbr-ingress-queues Egress PBR Ingress Shared Queue Policy
===============================================================================
*A:PE#
|
Label |
Description |
|---|---|
|
Policy |
The ID that uniquely identifies the policy. |
|
Description |
A text string that helps identify the policy context in the configuration file. |
shcv-policy
shcv-policy
Syntax
shcv-policy [policy-name]
Context
[Tree] (show>subscr-mgmt shcv-policy)
Full Context
show subscriber-mgmt shcv-policy
Description
This command displays the SHCV policy parameters.
Parameters
- policy-name
-
Specifies the SHCV policy name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of SHCV policy information. Output fields: SHCV policy describes the output fields.
Output Example# show subscriber-mgmt shcv-policy "shcv-1"
===============================================================================
SHCV policy "shcv-1"
===============================================================================
Description : (Not Specified)
Last management change : 09/27/2021 09:50:58
VPLS
IPv4 source address : (Not Specified)
Source MAC address : (Not Specified)
Layer 3
Source IP address origin : interface
Unnumbered source IP address: (Not Specified)
Periodic
Administrative state : enabled
Action : alarm
Interval (minutes) : 30
Retry count : 2
Retry timeout (s) : 10
-------------------------------------------------------------------------------
Triggered
-------------------------------------------------------------------------------
ip-conflict
Administrative state : enabled
Retry count : 1
Retry timeout (s) : 1
host-limit-exceeded
Administrative state : enabled
Retry count : 1
Retry timeout (s) : 1
inactivity
Administrative state : enabled
Retry count : 2
Retry timeout (s) : 10
mobility
Administrative state : enabled
Retry count : 1
Retry timeout (s) : 1
mac-learning
Administrative state : enabled
Retry count : 2
Retry timeout (s) : 10
===============================================================================
|
Label |
Description |
|---|---|
|
Description |
Displays the SHCV policy description |
|
Last management change |
Displays the date and time when the policy was last changed |
|
VPLS |
SHCV parameters applicable for VPLS services |
|
IPv4 source address |
Displays the IPv4 source address (sender IP address) used in SHCV ARP requests sent to host addresses learned using DHCP snooping in a VPLS service |
|
Source MAC address |
Displays the source MAC address used in SHCV ARP requests sent to host addresses learned using DHCP snooping in a VPLS service |
|
Layer 3 |
SHCV parameters applicable for Layer 3 services |
|
Source IP address origin |
Displays the source IP address origin:
|
|
Unnumbered source IP address |
Displays the IPv4 source address (sender IP address) used in SHCV ARP requests for unnumbered hosts |
|
Periodic |
SHCV parameters applicable for periodic and OAM checks |
|
Administrative state |
Displays the administrative state for periodic and OAM checks (enabled, disabled) |
|
Action |
Displays the action for unsuccessful checks:
|
|
Interval (minutes) |
Displays the interval between subsequent periodic checks |
|
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
|
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or execution of the SHCV unsuccessful check action |
|
Triggered |
SHCV parameters applicable for triggered checks |
|
ip-conflict |
SHCV parameters applicable for checks triggered by an IP conflict: a new host with different MAC address and same IP address as an existing host active on the same SAP |
|
Administrative state |
Displays the administrative state for ip-conflict triggered checks (enabled, disabled) |
|
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
|
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the existing host from the system |
|
host-limit-exceeded |
SHCV parameters applicable for checks triggered by a host limit exceeded event |
|
Administrative state |
Displays the administrative state for host-limit-exceeded triggered checks (enabled, disabled) |
|
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
|
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the unresponsive existing host from the system |
|
inactivity |
SHCV parameters applicable for checks triggered by an inactivity detection |
|
Administrative state |
Displays the administrative state for host-limit-exceeded triggered checks (enabled, disabled) |
|
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
|
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the unresponsive inactive host from the system |
|
mobility |
SHCV parameters applicable for checks triggered by a mobility event: a new host with same MAC address and same IP address as an existing host active on a different SAP |
|
Administrative state |
Displays the administrative state for mobility triggered checks (enabled, disabled) |
|
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
|
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the existing host from the system |
|
mac-learning |
SHCV parameters applicable for checks triggered for mac learning of IP only static hosts |
|
Administrative state |
Displays the administrative state for mac-learning triggered checks (enabled, disabled) |
|
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
|
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry |
sid-egress-stats
sid-egress-stats
Syntax
sid-egress-stats adj [interface-name]
sid-egress-stats adj-set [id]
sid-egress-stats all
sid-egress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>ospf sid-egress-stats)
[Tree] (clear>router>isis sid-egress-stats)
Full Context
clear router ospf sid-egress-stats
clear router isis sid-egress-stats
Description
This command clears the IS-IS or OSPF egress SID statistics.
Parameters
- adj
-
Clears the egress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs egress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID egress statistics for the interface specified by this interface name up to 32 characters.
- adj-set
-
Clears the egress statistics of the adjacency set specified by the corresponding ID. Clears all adjacency sets egress statistics if no adjacency set is specified.
- id
-
Clears the SID egress statistics for the identifier specified for this adjacency set.
- all
-
Clears all the SID egress statistics.
- node
-
Clears the egress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs egress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-egress-stats
Syntax
sid-egress-stats adj [interface-name]
sid-egress-stats all
sid-egress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>ospf3 sid-egress-stats)
Full Context
clear router ospf3 sid-egress-stats
Description
This command clears the OSPF3 egress SID statistics.
Parameters
- adj
-
Clears the egress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs egress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID egress statistics for the interface specified by this interface name up to 32 characters.
- all
-
Clears all the SID egress statistics.
- node
-
Clears the egress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs egress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-ingress-stats
sid-ingress-stats
Syntax
sid-ingress-stats adj [interface-name]
sid-ingress-stats adj-set [id]
sid-ingress-stats all
sid-ingress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>isis sid-ingress-stats)
[Tree] (clear>router>ospf sid-ingress-stats)
Full Context
clear router isis sid-ingress-stats
clear router ospf sid-ingress-stats
Description
This command clears the IS-IS or OSPF ingress SID statistics.
Parameters
- adj
-
Clears the ingress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs ingress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID ingress statistics for the interface specified by this interface name up to 32 characters.
- adj-set
-
Clears the ingress statistics of the adjacency set specified by the corresponding ID. Clears all adjacency sets ingress statistics if no adjacency set is specified.
- id
-
Clears the SID ingress statistics for the identifier specified for this adjacency set.
- all
-
Clears all the SID ingress statistics.
- node
-
Clears the ingress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs ingress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-ingress-stats
Syntax
sid-ingress-stats adj [interface-name]
sid-ingress-stats all
sid-ingress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>ospf3 sid-ingress-stats)
Full Context
clear router ospf3 sid-ingress-stats
Description
This command clears the OSPF3 ingress SID statistics.
Parameters
- adj
-
Clears the ingress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs ingress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID ingress statistics for the interface specified by this interface name up to 32 characters.
- all
-
Clears all the SID ingress statistics.
- node
-
Clears the ingress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs ingress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-stats
sid-stats
Syntax
sid-stats adj [interface-name]
sid-stats adj-set [id]
sid-stats node [ip-prefix[/ prefix-length]] [algo algo-id]
sid-stats summary
Context
[Tree] (show>router>ospf sid-stats)
[Tree] (show>router>isis sid-stats)
Full Context
show router ospf sid-stats
show router isis sid-stats
Description
This command displays information about IGP SIDs statistics.
Parameters
- interface-name
-
Displays only the SID statistics identified by this interface name up to 32 characters.
- id
-
Displays the adjacency set ID.
- ip-prefix[/prefix-length]
-
Displays information for the specified IP prefix and prefix length.
- algo-id
-
Displays the algorithm identifier.
- adj
-
Displays the ingress and egress statistics, if any, of the adjacency SID specified by the corresponding interface name. Displays statistics for all adjacency SIDs if none is specified.
- adj-set
-
Displays the ingress and egress statistics, if any, of the adjacency set specified by its associated ID. Displays statistics for all adjacency sets if none is specified.
- node
-
Displays the ingress and egress statistics, if any, of the node SID specified by the corresponding prefix. Displays statistics for all node SIDs if none is specified.
- algo
-
Displays statistics for the specified algorithm identifier.
- summary
-
Displays statistics indices usage for SID statistics.
Platforms
All
Output
The following outputs are examples of SID statistics information and Output fields: SID statistics adjacency set describes the output fields.
Output ExampleThe show router ospf sid-stats adj command displays statistics for adjacency SIDs.
===============================================================================
Label : 20001 Type : adjacency
Prefix : 10.1.2.2/32
Interface : to_Dut-B
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf sid-stats adj-set command displays statistics for adjacency set SIDs.
===============================================================================
Label : 20001 Type : adjacencySet
Prefix : 2.1.20.10/32
Adjacency-set : 23
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf sid-stats node command displays statistics for the specified algorithm.
*A:Dut-C# show router ospf sid-stats node algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Sid Statistics
===============================================================================
Ingress Label : 101282 Type : node
Prefix : 10.20.1.2/32
Algorithm : 128
Ingress Oper State: disabled Egress Oper State : disabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
Ingress Label : 101283 Type : node
Prefix : 10.20.1.3/32
Algorithm : 128
Ingress Oper State: disabled Egress Oper State : disabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
Ingress Label : 101285 Type : node
Prefix : 10.20.1.5/32
Algorithm : 128
Ingress Oper State: disabled Egress Oper State : disabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
-------------------------------------------------------------------------------
Sid count : 3
===============================================================================
*A:Dut-C#
The show router ospf sid-stats node command displays statistics for node SIDs.
===============================================================================
Label : 20001 Type : node
Prefix : 1.1.1.1/32
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf sid-stats summary command displays summary statistics for SIDs.
===============================================================================
Rtr Base OSPFv2 Instance 0 Sid Statistics (summary)
===============================================================================
===============================================================================
SID Statistics summary
===============================================================================
Node Adj Adj-Set
-------------------------------------------------------------------------------
SID Ingress Statistics indexes : 0/0 0/0 0/0
SID Egress Statistics indexes : 0/0 0/0 0/0
-------------------------------------------------------------------------------
<stats>/<sids> : <stats> = number of statistics indexes of specified type
<sids> = total number of SIDs of specified type for which the
statistic is applicable
===============================================================================
|
Label |
Description |
|---|---|
|
Label |
The ILM MPLS label corresponding to the SID. |
|
Type |
The type of the SID. |
|
Prefix |
The prefix corresponding to the node SID, or the IP address of the neighbor (adjacency SID) or the destination IP associated to the adjacency set. |
|
Interface |
The OSPF interface. |
|
Ingress Oper State |
Indicates if ingress statistics are enabled or disabled, or if no statistics index is allocated to that SID (no resources). |
|
Egress Oper State |
Indicates if egress statistics are enabled or disabled, or if no statistics index is allocated to that SID (no resources). |
|
Ingress Octets |
The number of octets received on ingress for that SID. |
|
Egress Octets |
The number of octets sent on egress for that SID. |
|
Ingress Packets |
The number of packets received on ingress for that SID. |
|
Egress Packets |
The number of packets sent on egress for that SID. |
sid-stats
Syntax
sid-stats adj [interface-name]
sid-stats node [ip-prefix[/ prefix-length]]
sid-stats summary
Context
[Tree] (show>router>ospf3 sid-stats)
Full Context
show router ospf3 sid-stats
Description
This command displays information about IGP SIDs statistics.
Parameters
- adj
-
Displays the ingress and egress statistics, if any, of the adjacency SID specified by the corresponding interface name. Displays statistics for all adjacency SIDs if none is specified.
- interface-name
-
Displays only the SID statistics identified by this interface name up to 32 characters.
- node
-
Displays the ingress and egress statistics, if any, of the node SID specified by the corresponding prefix. Displays statistics for all node SIDs if none is specified.
- ip-prefix[/prefix-length]
-
Displays information for the specified IP prefix and prefix length.
- summary
-
Displays stat indices usage for SID statistics.
Platforms
All
Output
The following outputs are an example of SID statistics information
Output ExampleThe show router ospf3 sid-stats adj command displays statistics for adjacency SIDs.
===============================================================================
Label : 20001 Type : adjacency
Prefix : 10.1.2.2/32
Interface : to_Dut-B
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf3 sid-stats node command displays statistics for node SIDs.
===============================================================================
Label : 20001 Type : node
Prefix : 1.1.1.1/32
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf3 sid-stats summary command displays summary statistics for SIDs.
===============================================================================
Rtr Base OSPFv3 Instance 0 Sid Statistics (summary)
===============================================================================
===============================================================================
SID Statistics summary
===============================================================================
Node Adj
-------------------------------------------------------------------------------
SID Ingress Statistics indexes : 0/0 0/0
SID Egress Statistics indexes : 0/0 0/0
-------------------------------------------------------------------------------
<stats>/<sids> : <stats> = number of statistics indexes of specified type
<sids> = total number of SIDs of specified type for which the
statistic is applicable
===============================================================================
site
site
Syntax
site [detail]
site name
Context
[Tree] (show>service>id site)
Full Context
show service id site
Description
This command displays site-specific information for the service.
Parameters
- name
-
Specifies the site name, up to 32 characters in length.
Platforms
All
site
Syntax
site name
Context
[Tree] (clear>service>id site)
Full Context
clear service id site
Description
This command clears site-specific information for the service.
Parameters
- name
-
Clears information about the specified service name, up to 32 characters.
Platforms
All
site-using
site-using
Syntax
site-using [site-name name] [site-id site-id]
Context
[Tree] (show>service site-using)
Full Context
show service site-using
Description
This command displays BGP multihoming sites used by services.
Parameters
- name
-
Specifies the BGP multihoming site name, up to 32 characters.
- site-id
-
Specifies the BGP multihoming site ID.
Platforms
All
sla-profile
sla-profile
Syntax
sla-profile [sla-profile-name [association]]
Context
[Tree] (show>subscr-mgmt sla-profile)
Full Context
show subscriber-mgmt sla-profile
Description
This command displays SLA profile information.
Parameters
- sla-profile-name
-
Specifies an existing SLA profile name.
- association
-
Displays the association information configured with the specified sla-profile-name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management SLA profile information.
Output Example# show subscriber-mgmt sla-profile "sla-profile-1"
===============================================================================
SLA Profile sla-profile-1
===============================================================================
Description : (Not Specified)
Control plane(s) : local
Host Limits : overall 1
ipv4-overall 1
ipv4-arp 1
ipv4-dhcp 1
ipv4-ppp 1
ipv6-overall 1
ipv6-pd-overall 1
ipv6-pd-ipoe-dhcp 1
ipv6-pd-ppp-dhcp 1
ipv6-wan-overall 1
ipv6-wan-ipoe-dhcp 1
ipv6-wan-ipoe-slaac 1
ipv6-wan-ppp-dhcp 1
ipv6-wan-ppp-slaac 1
lac-overall 1
remove-oldest
Session Limits : ipoe 1
pppoe-local 1
pppoe-lac 1
pppoe-overall 1
l2tp-lns 1
l2tp-lts 1
l2tp-overall 1
overall 1
Egr Sched-Policy : N/A
Ingress Qos-Policy : 1 Egress Qos-Policy : 1
Ingress Queuing Type : Service-queuing (Not Applicable to Policer)
Ingr IP Fltr-Id : N/A Egr IP Fltr-Id : N/A
Ingr IPv6 Fltr-Id : N/A Egr IPv6 Fltr-Id : N/A
Ingress Report-Rate : Maximum
Egress Report-Rate : Maximum
Egress Remarking : from Sap Qos
Credit Control Pol. : N/A
Category Map : (Not Specified)
Use ing L2TP DSCP : false
Default SPI sharing : per-sap
Hs-Agg-Rate-Limit : Maximum
Egress HS Q stat mode: no-override
Bonding Rate-thresh. : high 90 low 80
Bonding Weight : weight 100 5
Last Mgmt Change : 09/30/2020 15:22:30
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue Overrides
-------------------------------------------------------------------------------
Queue Rate CIR HiPrio CBS MBS AvgOvrHd StatMode
-------------------------------------------------------------------------------
No ingress overrides configured.
-------------------------------------------------------------------------------
Egress Queue Overrides
-------------------------------------------------------------------------------
Queue Rate CIR HiPrio CBS MBS AvgOvrHd StatMode
HsClssWght HsWrrWght HsWredQueuePol
-------------------------------------------------------------------------------
No egress overrides configured.
-------------------------------------------------------------------------------
Ingress Policer Overrides
-------------------------------------------------------------------------------
Plcr Rate CIR CBS MBS ByteOffset StatMode
-------------------------------------------------------------------------------
No ingress overrides configured.
-------------------------------------------------------------------------------
Egress Policer Overrides
-------------------------------------------------------------------------------
Plcr Rate CIR CBS MBS ByteOffset StatMode
-------------------------------------------------------------------------------
No egress overrides configured.
-------------------------------------------------------------------------------
QoS statistics aggregation
-------------------------------------------------------------------------------
Ingress policers: all
Ingress queues : all
Egress policers : all
Egress queues : all
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Egress HS WRR Group Overrides
-------------------------------------------------------------------------------
WrrGroupId ClassWeight Rate
-------------------------------------------------------------------------------
No egress overrides configured.
===============================================================================
# show subscriber-mgmt sla-profile
===============================================================================
SLA Profiles
===============================================================================
Name Description
-------------------------------------------------------------------------------
sla_default
sla_prof100_VOIP
sla_prof110_VOIP
sla_prof120_VOIP
sla_prof130_VOIP
sla_prof140_VOIP
sla_prof230_VOIP
sla_prof80
sla_prof80_VOIP
sla_prof81_VOIP
sla_prof90_VOIP
sla_profPC1
sla_profPC2
sla_profPC3
-------------------------------------------------------------------------------
Number of SLA Profiles : 14
===============================================================================
A:Dut-A#
# show subscriber-mgmt sla-profile sla_prof100_VOIP association
===============================================================================
SLA Profile sla_prof100_VOIP
-------------------------------------------------------------------------------
SAP Default-Profile Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
SAP Static Host Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
SAP Non-Sub-Traffic-Profile Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
Sub-Ident-Policy Profile Map Associations
-------------------------------------------------------------------------------
Policy-name : sub_ident_all
- Key : sla_prof100_VOIP
-------------------------------------------------------------------------------
Sub-Profile Map Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
Explicit Subscriber Map Associations
-------------------------------------------------------------------------------
No associations found.
===============================================================================
A:Dut-A#
Output fields: SLA profile describes subscriber management SLA profile output fields.
|
Field |
Description |
|---|---|
|
Name |
The Service Level Agreement (SLA) profile name |
|
Description |
The user provided description of this policy |
|
Number of SLA Profiles |
The total number of SLA profiles configured on this node |
|
Control plane(s) |
The SLA profile controlled by local control plane or CUPS control plane |
|
Host Limits |
The configured maximum number of hosts per SLA profile instance |
|
Session Limits |
The configured maximum number of sessions per SLA profile instance |
|
Ingress Qos-Policy |
The ingress QoS policy ID |
|
Egress Qos-Policy |
The egress QoS policy ID |
|
Ingress Queuing Type |
The queuing type |
|
Ingress Filter-Id |
The ingress IP filter |
|
Egress Filter-Id |
The egress IP filter |
|
Last Mgmt Change |
The time and date of the most recent management-initiated change |
|
Queue |
The ingress queue ID |
|
Rate |
The SLA profile queue rate |
|
CIR |
The CIR rate |
|
HiPrio |
The number of high priority packets as determined by the SLA profile ingress QoS policy |
|
CBS |
The amount of reserved buffer space (in bytes) for the policer |
|
MBS |
The amount of buffer space (in bytes) allowed for the policer |
slaac
slaac
Syntax
slaac
Context
[Tree] (clear>service>id slaac)
Full Context
clear service id slaac
Description
Commands in this context clear Stateless Address Auto-Configuration (SLAAC) related data for the service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
slaac
Syntax
slaac
Context
[Tree] (show>service>id slaac)
Full Context
show service id slaac
Description
This command displays SLAAC information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
slm
slm
Syntax
slm lmm [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>oam-pm>session slm)
Full Context
monitor oam-pm session slm
Description
This command monitors the Ethernet Synthetic Loss Measurement (SLM) statistics for the specified test's raw measurement interval.
Parameters
- seconds
-
Specifies the time interval, in seconds.
- repeat
-
Specifies the number of times the command is repeated.
- absolute
-
Specifies that the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Specifies that the rate-per-second is displayed.
Platforms
All
slm
Syntax
slm
Context
[Tree] (show>oam-pm>stats>session slm)
Full Context
show oam-pm statistics session slm
Description
This command selects the session's Ethernet SLM test for the statistical display.
Platforms
All
slope-policy
slope-policy
Syntax
slope-policy [slope-policy-name] [detail]
Context
[Tree] (show>qos slope-policy)
Full Context
show qos slope-policy
Description
This command displays slope policy information.
Parameters
- slope-policy-name
-
The name of the slope policy.
- detail
-
Displays detailed information about the slope policy.
Platforms
All
Output
The following output is an example of slope QoS policy information, and Output fields: QoS slope policy describes slope QoS policy output fields.
Output Example*A:PE# show qos slope-policy "slope1"
===============================================================================
QoS Slope Policy
===============================================================================
Policy : slope1
Description : (Not Specified)
Time Avg : 7
-------------------------------------------------------------------------------
HighPlus Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 75 Admin State : Enabled
Max Avg : 100 Max Prob. : 100
-------------------------------------------------------------------------------
High Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 50 Admin State : Enabled
Max Avg : 65 Max Prob. : 100
-------------------------------------------------------------------------------
Low Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 30 Admin State : Enabled
Max Avg : 40 Max Prob. : 100
-------------------------------------------------------------------------------
Exceed Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 10 Admin State : Enabled
Max Avg : 25 Max Prob. : 100
===============================================================================
*A:PE#
*A:PE# show qos slope-policy "slope1" detail
===============================================================================
QoS Slope Policy
===============================================================================
Policy : slope1
Description : (Not Specified)
Time Avg : 7
-------------------------------------------------------------------------------
HighPlus Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 75 Admin State : Enabled
Max Avg : 100 Max Prob. : 100
-------------------------------------------------------------------------------
High Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 50 Admin State : Enabled
Max Avg : 65 Max Prob. : 100
-------------------------------------------------------------------------------
Low Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 30 Admin State : Enabled
Max Avg : 40 Max Prob. : 100
-------------------------------------------------------------------------------
Exceed Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 10 Admin State : Enabled
Max Avg : 25 Max Prob. : 100
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
Object Type Object Id Application Pool
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
WRED Slot/FP Associations
-------------------------------------------------------------------------------
Slot FP
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
WRED SAP Queue Associations
-------------------------------------------------------------------------------
Policy-Id Queue-Id
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
WRED QoS Queue-Group Associations
-------------------------------------------------------------------------------
Queue-Group Queue-Id
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
*A:PE#
|
Label |
Description |
|---|---|
|
Policy |
The ID that uniquely identifies the policy. |
|
Description |
A string that identifies the policy context in the configuration file. |
|
Time Avg |
The weighting between the previous shared buffer average utilization result and the new shared buffer utilization. |
|
Slope Parameters |
|
|
Start Avg |
Specifies the RED slope position for the shared buffer average utilization value where the packet discard probability starts to increase above zero. |
|
Max Avg |
Specifies the percentage of the shared buffer space for the buffer pool at which point the drop probability becomes one, expressed as a decimal integer. |
|
Admin State |
Enabled The administrative status of the RED slope is enabled. Disabled The administrative status of the RED slope is disabled. |
|
Max Prob. |
Specifies the RED slope position for the maximum non-one packet discard probability value before the packet discard probability rises directly to one. |
smet
smet
Syntax
smet [hunt | detail] [rd rd] [community comm-id] [tag tag] [next-hop next-hop] [aspath-regex reg-exp] [originator-ip ip-address | ipv6-address]
Context
[Tree] (show>router>bgp>routes>evpn smet)
Full Context
show router bgp routes evpn smet
Description
This command displays BGP-EVPN SMET routes.
Parameters
- hunt
-
Displays entries for the specified route.
- detail
-
Displays detailed information.
- rd
-
Displays information for the route distinguisher.
- comm-id
-
Specifies the community ID, up to 72 characters.
- tag
-
Specifies the SMET route tag.
- next-hop
-
Specifies the IPv4 or IPv6 BGP next-hop address.
- reg-exp
-
Displays routes matching the specified regular expression, up to 80 characters.
- ip-address | ipv6-address
-
Specifies the originator IPv4 or IPv6 address, up to 64 characters.
Platforms
All
snippets
snippets
Syntax
snippets [detail]
snippets name snippet-name [instance snippet-instance] [detail]
Context
[Tree] (show>service>dynsvc>script snippets)
Full Context
show service dynamic-services script snippets
Description
This command displays the dynamic services snippets information. A snippet is the name of a set of Python functions to create, modify or destroy configuration; for example: a snippet called 'vprn' to create, modify, or destroy VPRN services.
The CLI output generated by a single dynamic service python function call is a snippet instance.
This command is not available in the MD-CLI.
Parameters
- detail
-
Displays dynamic services snippet information.
- snippet-name
-
Specifies the snippet name.
- snippet-instance
-
Specifies the snippet instance.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of dynamic service snippets.
Output Example# show service dynamic-services script snippets
===============================================================================
Dynamic Services Snippets
===============================================================================
Name Instance Ref-count Dict-len
-------------------------------------------------------------------------------
vprn VRF-1 1 75
vprn_1 1/1/1:1.901 0 190
-------------------------------------------------------------------------------
No. of Snippets: 2
===============================================================================
# show service dynamic-services script snippets detail
===============================================================================
Dynamic Service Snippets
===============================================================================
Snippet : vprn:VRF-1
-------------------------------------------------------------------------------
reference-count : 1
dictionary-length : 75
Root-object
-----------
oid : svcRowStatus.100000
Reserved-id
-----------
id : service-id:100000
-------------------------------------------------------------------------------
Snippet : vprn_1:1/1/1:1.901
-------------------------------------------------------------------------------
reference-count : 0
dictionary-length : 190
Referenced-snippet
------------------
snippet : vprn:VRF-1
-------------------------------------------------------------------------------
No. of Snippets: 2
===============================================================================
Output fields: script snippet describes snippets fields.
|
Output field |
Description |
|---|---|
|
Name |
The snippet name. |
|
Instance |
The snippet instance. |
|
Ref-count reference-count |
The number of times this snippet is referenced by other snippets. |
|
Dict-len dictionary-length |
The length of the python dictionary stored for this snippet. |
|
Root-object |
The object created by a Dynamic Service of which the parent is not created by a Dynamic Service. |
snmp
snmp
Syntax
snmp
Context
[Tree] (show snmp)
Full Context
show snmp
Description
Commands in this context display SNMP configuration.
Platforms
All
snmp
Syntax
snmp
Context
[Tree] (show>system>security snmp)
Full Context
show system security snmp
Description
Commands in this context show SNMP information.
Platforms
All
snmp-trap-group
snmp-trap-group
Syntax
snmp-trap-group [log-id]
Context
[Tree] (show>service>id>log snmp-trap-group)
Full Context
show service id log snmp-trap-group
Description
This command displays SNMP trap group configuration information.
Parameters
- log-id
-
Displays only SNMP trap group information for the specified trap group log ID.
Platforms
All
Output
SNMP Trap Group Output
Output fields: SNMP trap group describes SNMP trap group output fields.
|
Label |
Description |
|---|---|
|
Log-ID |
The log destination ID for an event stream. |
|
Address |
The IP address of the trap receiver. |
|
Port |
The destination UDP port used for sending traps to the destination, expressed as a decimal integer. |
|
Version |
Specifies the SNMP version format to use for traps sent to the trap receiver. Valid values are snmpv1, snmpv2c, snmpv3. |
|
Community |
The community string required by snmpv1 or snmpv2c trap receivers. |
|
Security-Level |
The required authentication and privacy levels required to access the views on this node. |
|
Replay |
Indicates whether or not the replay parameter has been configured, enabled or disabled, for the trap-target address. |
|
Replay from |
Indicates the sequence ID of the first missed notification that will be replayed when a route is added to the routing table by which trap-target address can be reached. If no notifications are waiting to be replayed this field shows n/a. |
|
Last Replay |
Indicates the last time missed events were replayed to the trap-target address. If no events have ever been replayed this field shows never. |
snmp-trap-group
Syntax
snmp-trap-group [log-id-or-log-name]
Context
[Tree] (show>log snmp-trap-group)
Full Context
show log snmp-trap-group
Description
This command displays SNMP trap group configuration information.
Parameters
- log-id-or-log-name
-
Displays only SNMP trap group information for the specified trap group log ID, up to 64 characters.
Platforms
All
Output
The following output is an example of SNMP trap group information.
Output fields: SNMP trap group describes SNMP trap group output fields.
Output ExampleA:SetupCLI>config>log>snmp-trap-group# show log snmp-trap-group 44
===============================================================================
SNMP Trap Group 44
===============================================================================
Description : none
-------------------------------------------------------------------------------
Name : ntt-test
Address : 10.10.10.3
Port : 162
Version : v2c
Community : ntttesting
Sec. Level : none
Replay : disabled
Replay from : n/a
Last replay : never
-------------------------------------------------------------------------------
Name : test2
Address : 10.20.20.5
Port : 162
Version : v2c
Community : ntttesting
Sec. Level : none
Replay : disabled
Replay from : n/a
Last replay : never
===============================================================================
A:SetupCLI>config>log>snmp-trap-group#
|
Label |
Description |
|---|---|
|
Log-ID/Name |
The log destination ID or name for an event stream. |
|
Address |
The IP address of the trap receiver, |
|
Port |
The destination UDP port used for sending traps to the destination, expressed as a decimal integer. |
|
Version |
Specifies the SNMP version format to use for traps sent to the trap receiver. Valid values are snmpv1, snmpv2c, snmpv3. |
|
Community |
The community string required by snmpv1 or snmpv2c trap receivers. |
|
Security-Level |
The required authentication and privacy levels required to access the views on this node. |
|
Replay |
Indicates whether or not the replay parameter has been configured, enabled or disabled, for the trap-target address. |
|
Replay from |
Indicates the sequence ID of the first missed notification that will be replayed when a route is added to the routing table by which trap-target address can be reached. If no notifications are waiting to be replayed this field shows n/a. |
|
Last Replay |
Indicates the last time missed events were replayed to the trap-target address. If no events have ever been replayed this field shows never. |
sntp
sntp
Syntax
sntp
Context
[Tree] (show>system sntp)
Full Context
show system sntp
Description
This command displays SNTP protocol configuration and state.
Platforms
All
Output
The following output is an example of SNTP information, and Output fields: system SNTP describes the output fields.
Output ExampleA:ALA-1# show system sntp
===============================================================================
SNTP
===============================================================================
SNTP Server Version Preference Interval
-------------------------------------------------------------------------------
10.10.20.253 3 Preferred 64
===============================================================================
A:ALA-1#
|
Label |
Description |
|---|---|
|
SNTP Server |
The SNTP server address for SNTP unicast client mode. |
|
Version |
The SNTP version number, expressed as an integer. |
|
Preference |
Normal — When more than one time server is configured, one server can be configured to have preference over another. Preferred — Indicates that this server has preference over another. |
|
Interval |
The frequency, in seconds, that the server is queried. |
sockets
sockets
Syntax
sockets
Context
[Tree] (tools>dump>router>ldp sockets)
Full Context
tools dump router ldp sockets
Description
This command dumps information for all LDP sockets.
Platforms
All
software-repository
software-repository
Syntax
software-repository [repository-name]
Context
[Tree] (show>system software-repository)
Full Context
show system software-repository
Description
This command displays software repository information.
Parameters
- repository-name
-
Specifies the software repository name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
source
source
Syntax
source [ip-address/mask] [type {configured | dynamic | both}] [detail]
Context
[Tree] (show>router>msdp source)
Full Context
show router msdp source
Description
This command displays the discovery method for the multicast source.
Parameters
- ip-address/mask
-
Specifies the source IP address and mask.
- configured
-
Keyword to display user-created sources.
- dynamic
-
Keyword to display dynamically created sources.
- both
-
Keyword to display both user-configured and dynamically created sources.
- detail
-
Keyword to display detailed MSDP source information.
Platforms
All
source-active
source-active
Syntax
source-active [{group ip-address | local | originator ip-address | peer ip-address | source ip-address | group ip-address source ip-address}] [detail]
Context
[Tree] (show>router>msdp source-active)
Full Context
show router msdp source-active
Description
This command displays SA messages accepted by MSDP.
Parameters
- group ip-address
-
Displays information about the specified group IP address.
- local
-
Keyword to display information about local source-active messages.
- originator ip-address
-
Displays information about the specified originator IP address.
- peer ip-address
-
Displays information about the specified peer IP address.
- source ip-address
-
Displays information about the specified source IP address.
- group ip-address
-
Displays information about the specified group IP address.
- detail
-
Keyword to display detailed MSDP source-active information.
Platforms
All
Output
The following output is an example of MSDP source active information, and Output fields: MSDP source active describes the output fields.
Output exampleA:ALA-48# show router msdp source-active
===============================================================================
MSDP Source Active Info
===============================================================================
Grp Address Src Address Origin RP Peer Address State Timer
-------------------------------------------------------------------------------
239.100.0.0 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.1 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.2 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.3 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.4 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.5 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.6 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.7 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.8 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.9 10.112.1.2 10.20.1.1 10.20.1.1 69
-------------------------------------------------------------------------------
MSDP Source Active : 10
===============================================================================
A:ALA-48#
A:ALA-48# show router msdp source-active detail
===============================================================================
MSDP Source Active
===============================================================================
Group Address : 239.100.0.0 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 3d 01:44:25
Group Address : 239.100.0.1 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.2 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.3 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.4 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.5 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.7 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.8 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.9 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
-------------------------------------------------------------------------------
MSDP Source Active : 10
===============================================================================
A:ALA-48#
|
Label |
Description |
|---|---|
|
Grp Address |
The IP address of the group |
|
Src Address |
The IP address of the source |
|
Origin RP |
The origination RP address |
|
Peer Address |
The address of the peer |
|
State Timer |
The time-out value. If the value reaches zero, the SA is removed. |
| Up time | The duration that the SA has been active |
source-active-rejected
source-active-rejected
Syntax
source-active-rejected [peer-group name] [ group ip-address] [source ip-address] [originator ip-address] [peer ip-address]
Context
[Tree] (show>router>msdp source-active-rejected)
Full Context
show router msdp source-active-rejected
Description
This command displays SA messages rejected by MSDP.
Parameters
- peer-group name
-
Displays information about rejected SA messages for the specified peer group.
- group ip-address
-
Displays information about the specified group IP address.
- source ip-address
-
Displays information about the source address of the source active entry that is rejected.
- originator ip-address
-
Displays information about the specified originator IP address.
- peer ip-address
-
Displays information about the peer from which this rejected source active entry was last received.
Platforms
All
Output
The following output is an example of MSDP rejected source active information, and Output fields: MSDP source active rejected describes the output fields.
Output example*A:ALA-48# show router msdp source-active-rejected
===============================================================================
MSDP Source Active Rejected Info
===============================================================================
Grp Address Src Address Origin RP Peer Address Reject Reason
-------------------------------------------------------------------------------
239.100.0.1 10.0.0.1 10.20.0.1 239.0.0.1 Import Policy
239.100.0.2 10.0.0.2 10.20.0.2 239.0.0.2 Export Policy
239.100.0.3 10.0.0.3 10.20.0.3 239.0.0.3 RPF Failure
239.100.0.4 10.0.0.4 10.20.0.4 239.0.0.4 Limit Exceeded
239.100.0.5 10.0.0.5 10.20.0.5 239.0.0.5 Limit Exceeded
239.100.0.6 10.0.0.6 10.20.0.6 239.0.0.6 Limit Exceeded
239.100.0.7 10.0.0.7 10.20.0.7 239.0.0.7 Limit Exceeded
-------------------------------------------------------------------------------
SA Rejected Entries : 7
===============================================================================
*A:ALA-48#
|
Label |
Description |
|---|---|
|
Grp Address |
The IP address of the group |
|
Src Address |
The IP address of the source |
|
Origin RP |
The origination rendezvous point (RP) address |
|
Peer Address |
The address of the peer |
|
Reject Reason |
The reason that the source active entry was rejected |
source-address
source-address
Syntax
source-address
Context
[Tree] (show>service>id source-address)
Full Context
show service id source-address
Description
This command displays the configured source addresses for applications in a VPRN.
Platforms
All
Output
The following output is an example of source address output information, and Output fields: source address describes the output fields.
Output ExampleA:SR-7# show service id 1 source-address
===============================================================================
Source-Address applications
===============================================================================
Application IP address/Interface Name Oper status
-------------------------------------------------------------------------------
telnet 10.20.1.7 Up
radius loopback1 Up
===============================================================================
A:SR-7#
|
Label |
Description |
|---|---|
|
Application |
Displays the application name |
|
IP address/Interface Name |
Displays the source IP address or interface name |
|
Oper status |
Up - The source address is operationally up Down - The source address is operationally down |
source-address
Syntax
source-address
Context
[Tree] (show>system>security source-address)
Full Context
show system security source-address
Description
This command displays the configured source addresses for applications in routing instances.
Platforms
All
Output
The following output is an example of source address output information, and Output fields: source address describes the output fields.
Output ExampleA:SR-7# show system security source-address
===============================================================================
Source-Address applications
===============================================================================
Application IP address/Interface Name Oper status
-------------------------------------------------------------------------------
telnet 10.20.1.7 Up
radius loopback1 Up
===============================================================================
A:SR-7#
|
Label |
Description |
|---|---|
|
Application |
Displays the application name |
|
IP address/Interface Name |
Displays the source IP address or interface name |
|
Oper status |
Up - The source address is operationally up Down - The source address is operationally down |
spb
spb
Syntax
spb
Context
[Tree] (clear>service>id spb)
Full Context
clear service id spb
Description
This command clears SPB related data.
Platforms
All
spb
Syntax
spb
Context
[Tree] (show>service>id spb)
Full Context
show service id spb
Description
Commands in this context display SPB related information.
Platforms
All
spf
spf
Syntax
spf
Context
[Tree] (show>service>id>spb spf)
Full Context
show service id spb spf
Description
This command displays SPF information.
Platforms
All
Output
The following output is an example of service SPB SPF information.
Output ExampleA:cses-B01# show service id spb spf
===============================================================================
Path Table
===============================================================================
Node Interface Nexthop
-------------------------------------------------------------------------------
Fwd Tree: unicast, ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
Fwd Tree: unicast, ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
Fwd Tree: multicast, ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
Fwd Tree: multicast, ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
===============================================================================
spf
Syntax
spf [lfa]
Context
[Tree] (show>router>ospf spf)
[Tree] (show>router>ospf3 spf)
Full Context
show router ospf spf
show router ospf3 spf
Description
This command displays statistics of shortest-path-first (SPF) calculations.
Parameters
- lfa
-
Displays Loop-Free Alternate (LFA) next-hop information.
Platforms
All
Output
SPF Output Fields
Output fields: SPF describes SPF output fields.
|
Label |
Description |
|---|---|
|
Total SPF Runs |
The total number of SPF runs triggered by new or updated LSAs. |
|
Last Full SPF run @ |
The date and time when the last full SPF was run. |
|
Last Full SPF Time |
The duration, in seconds, of the last full SPF calculation. Last Full SPF Time = Intra SPF Time + Inter SPF Time + Extern SPF Time + RTM Updt Time. |
|
Intra SPF Time |
The duration, in seconds, of the Intra-area phase of the last SPF calculation. |
|
Inter SPF Time |
The duration, in seconds, of the Inter-area phase of the last SPF calculation. |
|
Extern SPF Time |
The duration, in seconds, of the External phase of the last SPF calculation. |
|
RTM Updt Time |
The duration, in seconds, of the RTM update phase of the last SPF calculation. |
|
Min/Avg/Max Full SPF Time |
Min The minimum time, in seconds, used to perform a full SPF calculation. Avg The average time, in seconds, of all the full SPF calculations performed by this OSPF router. Max The maximum time, in seconds, used to perform a full SPF calculation. |
|
Total Sum Incr SPF Runs |
The total number of incremental SPF runs triggered by new or updated type-3 and type-4 summary LSAs. |
|
Total Ext Incr SPF Runs |
The total number of incremental SPF runs triggered by new or updated type-5 external LSAs. |
*A:Dut-C# show router ospf spf
===============================================================================
Rtr Base OSPFv2 Instance 0 SPF Statistics
===============================================================================
Total SPF Runs : 6
Last Full SPF run @ : 05/27/2015 08:45:25
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.00/0.00/0.00 secs
Min/Avg/Max RTM Updt Times : 0.00/0.00/0.00 secs
Total Sum Incr SPF Runs : 9
Last Sum Incr SPF run @ : 05/27/2015 08:36:14
Last Sum Incr Calc Time : < 0.01 secs
Total Ext Incr SPF Runs : 0
===============================================================================
*A:Dut-C# show router ospf spf lfa
===============================================================================
Rtr Base OSPFv2 Instance 0 SPF Statistics
===============================================================================
Total SPF Runs : 6
Last Full SPF run @ : 05/27/2015 08:45:25
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.00/0.00/0.00 secs
Min/Avg/Max RTM Updt Times : 0.00/0.00/0.00 secs
Total Sum Incr SPF Runs : 9
Last Sum Incr SPF run @ : 05/27/2015 08:36:14
Last Sum Incr Calc Time : < 0.01 secs
Total Ext Incr SPF Runs : 0
Total LFA SPF Runs : 1
Last LFA SPF run @ : 05/27/2015 08:45:25
Last LFA SPF Time : < 0.01 secs
Min/Avg/Max LFA SPF Times : 0.00/0.00/0.00 secs
===============================================================================
A:Dut-A# show router ospf 1 spf lfa
=======================================================================
Rtr Base OSPFv2 Instance 1 SPF Statistics
=======================================================================
Total SPF Runs : 6
Last Full SPF run @ : 02/20/2012 09:19:35
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.00/0.00/0.00 secs
Min/Avg/Max RTM Updt Times : 0.00/0.00/0.00 secs
Total Sum Incr SPF Runs : 0
Total Ext Incr SPF Runs : 0
Total LFA SPF Runs : 5
Last LFA SPF run @ : 02/20/2012 09:19:35
Last LFA SPF Time : < 0.01 secs
Min/Avg/Max LFA SPF Times : 0.00/0.00/0.00 secs
=======================================================================
A:ALA-A# show router ospf 1 spf
===============================================================================
Rtr Base OSPFv2 Instance 1 SPF Statistics
===============================================================================
Total SPF Runs : 109
Last Full SPF run @ : 11/07/2006 18:43:07
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.02/0.00/0.06 secs
Min/Avg/Max RTM Updt Times : 0.02/0.00/0.06 secs
Total Sum Incr SPF Runs : 333
Last Sum Incr SPF run @ : 11/07/2006 18:43:09
Last Sum Incr Calc Time : < 0.01 secs
Total Ext Incr SPF Runs : 0
===============================================================================
A:ALA-A#
spf-log
spf-log
Syntax
spf-log
Context
[Tree] (show>service>id>spb spf-log)
Full Context
show service id spb spf-log
Description
This command displays SPF Log information.
Platforms
All
Output
The following output is an example of service SPB SPF log information.
Output ExampleA:cses-B01# show service id spb spf-log
===============================================================================
ISIS SPF Log
===============================================================================
When Duration L1 Nodes L2 Nodes Event Count Type
-------------------------------------------------------------------------------
07/23/2012 16:01:13 <0.01s 1 0 1 Reg
07/23/2012 16:01:19 <0.01s 1 0 4 Reg
07/23/2012 16:01:24 <0.01s 3 0 2 Reg
07/23/2012 16:01:29 <0.01s 4 0 1 Reg
-------------------------------------------------------------------------------
Log Entries : 4
-------------------------------------------------------------------------------
spf-log
Syntax
spf-log [detail]
Context
[Tree] (show>router>isis spf-log)
Full Context
show router isis spf-log
Description
This command displays IS-IS SPF log information.
Parameters
- detail
-
Displays detailed spf-log information.
Platforms
All
Output
The following output is an example of SPF log information.
Output Example*A:Dut-C# show router isis spf-log
===============================================================================
Rtr Base ISIS Instance 0 SPF Log
===============================================================================
When Duration L1 Nodes L2 Nodes Event Count Type
-------------------------------------------------------------------------------
01/26/2015 11:22:19 <0.01s - - - pLfa
01/26/2015 11:22:19 <0.01s - - - rLfa
01/26/2015 11:22:20 <0.01s 4 4 25 Reg
01/26/2015 11:22:20 <0.01s - - - Lfa
01/26/2015 11:22:20 <0.01s - - - rLfa
01/26/2015 11:22:24 <0.01s 4 4 11 Reg
01/26/2015 11:22:24 <0.01s - - - Lfa
01/26/2015 11:22:24 <0.01s - - - rLfa
01/26/2015 11:22:32 <0.01s 4 4 21 Reg
01/26/2015 11:22:32 <0.01s - - - Lfa
01/26/2015 11:22:32 <0.01s - - - rLfa
01/26/2015 11:22:33 <0.01s - - - pSpf
01/26/2015 11:22:33 <0.01s - - - pLfa
01/26/2015 11:22:33 <0.01s - - - rLfa
01/26/2015 11:22:41 <0.01s - - - pSpf
01/26/2015 11:22:41 <0.01s - - - pLfa
01/26/2015 11:22:41 <0.01s - - - rLfa
01/26/2015 11:22:51 <0.01s 4 4 4 Reg
01/26/2015 11:22:51 <0.01s - - - Lfa
01/26/2015 11:22:51 <0.01s - - - rLfa
-------------------------------------------------------------------------------
Log Entries : 20
===============================================================================
*A:Dut-C#
A:SetupCLI# show router isis spf-log detail
===============================================================================
Rtr Base ISIS Instance 0 SPF Log
===============================================================================
When : 10/01/2011 03:40:25 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 78
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:26 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:25 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 25
SPF Type : Reg
Reason : NEWAREA NEWREACH LSPCONTENT MANUALREQ
When : 10/01/2011 03:40:27 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:27 Duration : <0.01s
L1 Nodes : 0 L2 Nodes : 0
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Lfa
Reason : LSPCONTENT
When : 10/01/2011 03:40:25 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 75
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:27 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Reg
Reason : LSPCONTENT
===============================================================================
A:SetupCLI#
Output fields: IS-IS SPF log describes the IS-IS SPF log output fields.
|
Label |
Description |
|---|---|
|
When |
Displays the timestamp when the SPF run started on the system. |
|
Duration |
Displays the time (in hundredths of a second) required to complete the SPF run. |
|
L1 Nodes |
Displays the number of Level 1 nodes involved in the SPF run. |
|
L2 Nodes |
Displays the number of Level 2 nodes involved in the SPF run. |
|
Event Count |
Displays the number of SPF events that triggered the SPF calculation. |
|
Type |
Displays the SPF type, Reg (regular) or Lfa (loop free alternative). |
|
Trigger LSP |
Displays the LSP that triggered the SPF run. |
|
Reason |
Displays the reason(s) for the SPF run. NEWADJ: An adjacency changed. NEWLSP: A new LSP was received. NEWAREA: An area changed. NEWREACH: A prefix changed. ECMPCHANGED: An ECMP path changed. NEWMETRIC: A prefix metric changed. RESTART: The graceful restart exited. LSPEXPIRED: An LSP expired. DBCHANGED: The LSP database was cleared by an administrator. LSPCONTENT: The content of an LSP changed. NEWPREF: The external route preference changed. NEWNLPID: The routed protocols (IPv4 or IPv6) changed. MANUALREQ: An SPF calculation was requested by an administrator. ADMINTAGCHANGED: An administrative tag changed. TUNNELCHANGED: An MPLS tunnel changed. |
spf-log
split-horizon-group
split-horizon-group
Syntax
split-horizon-group [group-name]
Context
[Tree] (show>service>id split-horizon-group)
Full Context
show service id split-horizon-group
Description
This command displays service split horizon groups.
Parameters
- group-name
-
Specifies a group name up to 32 characters.
Platforms
All
Output
The following output is an example of service split horizon group information.
Output ExampleA:ALA-1# show service id 700 split-horizon-group
=============================================================================
Service: Split Horizon Group
=============================================================================
Name Description
-----------------------------------------------------------------------------
R DSL-group1 Split horizon group for DSL
-----------------------------------------------------------------------------
R = Residential Split Horizon Group
No. of Split Horizon Groups: 1
=============================================================================
A:ALA-1#
A:ALA-1# show service id 700 split-horizon-group DSL-group1
===============================================================================
Service: Split Horizon Group
===============================================================================
Name Description
-------------------------------------------------------------------------------
R DSL-group1 Split horizon group for DSL
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
SAP 1/1/3:1
SDP 108:1
SDP 109:1
-------------------------------------------------------------------------------
R = Residential Split Horizon Group
SAPs Associated : 1 SDPs Associated : 2
===============================================================================
A:ALA-1#
spmsi-ad
spmsi-ad
Syntax
spmsi-ad [hunt | detail] [rd rd] [community comm-id] [tag tag] [next-hop next-hop] [aspath-regex reg-exp] [originator-ip ip-address | ipv6-address]
Context
[Tree] (show>router>bgp>routes>evpn spmsi-ad)
Full Context
show router bgp routes evpn spmsi-ad
Description
This command displays BGP-EVPN SPMSI AD routes.
Parameters
- hunt
-
Displays entries for the specified route.
- detail
-
Displays detailed information.
- rd
-
Displays information for the route distinguisher.
- comm-id
-
Specifies the community ID, up to 72 characters.
- tag
-
Specifies the SPMSI AD route tag.
- next-hop
-
Specifies the IPv4 or IPv6 BGP next-hop address.
- reg-exp
-
Displays routes matching the specified regular expression, up to 80 characters.
- ip-address | ipv6-address
-
Specifies the originator IPv4 or IPv6 address, up to 64 characters.
Platforms
All
spoke-sdp
spoke-sdp
Syntax
spoke-sdp sdp-id[:vc-id] {all | counters | stp | l2pt | mrp}
Context
[Tree] (clear>service>statistics>id spoke-sdp)
Full Context
clear service statistics id spoke-sdp
Description
This command clears statistics for the spoke SDP bound to the service.
Parameters
- sdp-id
-
The spoke SDP ID for which to clear statistics
- vc-id
-
The virtual circuit ID on the SDP ID to be reset
- all
-
Clears all queue statistics and STP statistics associated with the SDP
- counters
-
Clears all queue statistics associated with the SDP
- stp
-
Clears all STP statistics associated with the SDP
- l2pt
-
Clears all L2PT statistics associated with the SDP
- mrp
-
Clears all MRP statistics associated with the SDP
Platforms
All
spoke-sdp
Syntax
spoke-sdp sdp-id:vc-id ingress-vc-label
spoke-sdp sdp-id:vc-id l2tpv3
spoke-sdp sdp-id:vc-id vccv-bfd {session | statistics}
Context
[Tree] (clear>service>id spoke-sdp)
Full Context
clear service id spoke-sdp
Description
This command clears and resets the spoke SDP bindings for the service.
Parameters
- sdp-id
-
The spoke SDP ID to be reset.
- vc-id
-
The virtual circuit ID on the SDP ID to be reset.
- ingress-vc-label
-
Specifies to clear the ingress VC label.
- l2tpv3
-
Specifies to clear the session mismatch flag on the spoke-SDP binding after the flag was set to true by a detected mismatch between the configured parameters and the received parameters.
- vccv-bfd
-
Specifies to clear the following information related to VCCV BFD on the spoke-sdp.
- session
-
Clears session information.
- statistics
-
Clears spoke SDP statistics.
Platforms
All
spoke-sdp-fec
spoke-sdp-fec
Syntax
spoke-sdp-fec [1 to 4294967295]
Context
[Tree] (show>service>id spoke-sdp-fec)
Full Context
show service id spoke-sdp-fec
Description
This command displays spoke-SDP FEC information.
Parameters
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of spoke-SDP FEC information.
Output Example===============================================================================
Service Spoke-SDP FEC Information
===============================================================================
Spoke-Sdp-Fec-Id : 1 Admin State : enabled
FEC Type : 129 AII Type : 2
Standby Sig Slave : disabled ICB : disabled
Signaling : auto Auto Config : disabled
PW Template Id : (none) Precedence : 4
Retry Timer : 10 secs Retry Count : 10
Retry Timer Remaining: 0 secs Retries Remaining: 0
SAII Type2 : 3:10.20.1.3:1
TAII Type2 : 6:10.20.1.6:1
Path : n/a
Endpoint : n/a
Oper SDP-Bind : 17407:4294967246
Last Error : <none>
===============================================================================
Entries found: 1
===============================================================================
spoke-sdp-fec-using
spoke-sdp-fec-using
Syntax
spoke-sdp-fec-using [spoke-sdp-fec-id spoke-sdp-fec-id] [ saii-type2 global-id:prefix:ac-id] [taii-type2 global-id:prefix:ac-id] [path name] [ expired]
Context
[Tree] (show>service spoke-sdp-fec-using)
Full Context
show service spoke-sdp-fec-using
Description
Displays the SDPs used by spoke-sdp-fecs at this node.
Parameters
- spoke-sdp-fec-id
-
Specifies the spoke-SDP FEC ID for which to show SDP information.
- global-id
-
Specifies the SAII or TAII global ID.
- prefix
-
Specifies the SAII or TAII prefix.
- ac-id
-
Specifies the SAII or TAII AC ID.
- name
-
Specifies the path name. 32 characters maximum.
- expired
-
Displays information for expired SDPs.
Platforms
All
Output
The following output is an example of spoke-SDP information.
Output Example*A:Dut-C# show service spoke-sdp-fec-using
===============================================================================
Service Spoke-SDP-Fec Information
===============================================================================
SvcId SpokeSdpFec Oper-SdpBind SAII-Type2
Path TAII-Type2
-------------------------------------------------------------------------------
1 1 17407:4294967245 3:10.20.1.3:1
n/a 6:10.20.1.6:1
2 2 17407:4294967247 3:10.20.1.3:2
n/a 6:10.20.1.6:2
3 3 17407:4294967248 3:10.20.1.3:3
n/a 6:10.20.1.6:3
4 4 17407:4294967249 3:10.20.1.3:4
n/a 6:10.20.1.6:4
5 5 17407:4294967250 3:10.20.1.3:5
n/a 6:10.20.1.6:5
6 6 17407:4294967251 3:10.20.1.3:6
n/a 6:10.20.1.6:6
7 7 17407:4294967252 3:10.20.1.3:7
n/a 6:10.20.1.6:7
8 8 17407:4294967253 3:10.20.1.3:8
n/a 6:10.20.1.6:8
9 9 17407:4294967254 3:10.20.1.3:9
n/a 6:10.20.1.6:9
10 10 17407:4294967255 3:10.20.1.3:10
n/a 6:10.20.1.6:10
-------------------------------------------------------------------------------
Entries found: 10
squelch-ingress-levels
squelch-ingress-levels
Syntax
squelch-ingress-levels [all | ctag-space] [ sdp-id[:vc-id]]
Context
[Tree] (show>service>sdp-using>eth-cfm squelch-ingress-levels)
Full Context
show service sdp-using eth-cfm squelch-ingress-levels
Description
This command displays the squelch ingress levels associated with SDP bindings.
Parameters
- sdp-id[:vc-id]
-
Specifies the SDP ID and virtual circuit ID on the SDP ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
sr-adj-sets
sr-adj-sets
Syntax
sr-adj-sets [adjacency-set-id] [detail]
Context
[Tree] (show>router>isis sr-adj-sets)
Full Context
show router isis sr-adj-sets
Description
This command displays IS-IS SR adjacency set log information.
Parameters
- adjacency-set-id
-
Displays SR adjacency set ID information.
- detail
-
Displays detailed SR adjacency set information.
Platforms
All
Output
The following output is an example of sr-adj-sets log information.
Output Example*A:Dut-C# show router isis sr-adj-sets
===============================================================================
Rtr Base ISIS Instance 0 Adjacency Sets
===============================================================================
ID State Label Label Members Members Neighbor
Value Type Total Active System Id
-------------------------------------------------------------------------------
1003 active 524285 DL 1 1 0100.2000.1001
1006 active 524284 DL 1 1 0100.2000.1005
1015 active 18448 SL 1 1 0100.2000.1001
1018 active 18451 SL 1 1 0100.2000.1005
1027 active 524283 DL 1 1 0100.2000.1001
1030 active 524282 DL 1 1 0100.2000.1005
1039 active 18460 SL 1 1 0100.2000.1001
1042 active 18463 SL 1 1 0100.2000.1005
1050 active 524281 DL 2 2 none
1056 active 18471 SL 2 2 none
1063 active 524280 DL 1 1 0100.2000.1001
1066 active 524279 DL 1 1 0100.2000.1005
1075 active 18478 SL 1 1 0100.2000.1001
1078 active 18481 SL 1 1 0100.2000.1005
1087 active 524278 DL 1 1 0100.2000.1001
1090 active 524277 DL 1 1 0100.2000.1005
1099 active 18490 SL 1 1 0100.2000.1001
1102 active 18493 SL 1 1 0100.2000.1005
1110 active 524276 DL 2 2 none
1116 active 18501 SL 2 2 none
-------------------------------------------------------------------------------
DL: dynamic local
SL: static local
-------------------------------------------------------------------------------
No. of SR Adjacency Sets: 20
===============================================================================
Output fields: IS-IS SR adjacency set describes the IS-IS sr-adj-sets output fields.
|
Label |
Description |
|---|---|
|
ID |
Displays the ID |
|
State |
Displays the state (active or inactive) |
|
Label Value |
Displays the label value |
|
Label Type |
Displays the label type, Dynamic Local (DL) or Static Local (SL) |
|
Members Total |
Displays the number of total members |
|
Members Active |
Displays the number of active members |
|
Neighbor System Id |
Displays the neighbor system ID |
|
No. of SR Adjacency Sets |
Displays the number of SR adjacency sets |
sr-adj-sets
Syntax
sr-adj-sets [adjacency-set-id] [detail]
Context
[Tree] (show>router>ospf sr-adj-sets)
Full Context
show router ospf sr-adj-sets
Description
This command displays OSPF SR adjacency set log information.
Parameters
- adjacency-set-id
-
Displays SR adjacency set ID information.
- detail
-
Displays detailed SR adjacency set information.
Platforms
All
Output
The following output is an example of sr-adj-sets log information.
Output Example*A:Dut-C# show router ospf sr-adj-sets
===============================================================================
Rtr Base OSPF Instance 0 Adjacency Sets
===============================================================================
ID State Label Label Members Members Neighbor
Value Type Total Active System Id
-------------------------------------------------------------------------------
1003 active 524285 DL 1 1 0100.2000.1001
1006 active 524284 DL 1 1 0100.2000.1005
1015 active 18448 SL 1 1 0100.2000.1001
1018 active 18451 SL 1 1 0100.2000.1005
1027 active 524283 DL 1 1 0100.2000.1001
1030 active 524282 DL 1 1 0100.2000.1005
1039 active 18460 SL 1 1 0100.2000.1001
1042 active 18463 SL 1 1 0100.2000.1005
1050 active 524281 DL 2 2 none
1056 active 18471 SL 2 2 none
1063 active 524280 DL 1 1 0100.2000.1001
1066 active 524279 DL 1 1 0100.2000.1005
1075 active 18478 SL 1 1 0100.2000.1001
1078 active 18481 SL 1 1 0100.2000.1005
1087 active 524278 DL 1 1 0100.2000.1001
1090 active 524277 DL 1 1 0100.2000.1005
1099 active 18490 SL 1 1 0100.2000.1001
1102 active 18493 SL 1 1 0100.2000.1005
1110 active 524276 DL 2 2 none
1116 active 18501 SL 2 2 none
-------------------------------------------------------------------------------
DL: dynamic local
SL: static local
-------------------------------------------------------------------------------
No. of SR Adjacency Sets: 20
===============================================================================
Output fields: OSPF SR adjacency set describes the OSPF sr-adj-sets output fields.
|
Label |
Description |
|---|---|
|
ID |
Displays the ID. |
|
State |
Displays the state (active or inactive). |
|
Label Value |
Displays the label value. |
|
Label Type |
Displays the label type, Dynamic Local (DL) or Static Local (SL). |
|
Members Total |
Displays the number of total members. |
|
Members Active |
Displays the number of active members. |
|
Neighbor System Id |
Displays the neighbor system ID. |
|
No. of SR Adjacency Sets |
Displays the number of SR adjacency sets. |
sr-adjacencies
sr-adjacencies
Syntax
sr-adjacencies [ip-int-name | ip-address] [detail]
Context
[Tree] (tools>dump>router>isis sr-adjacencies)
Full Context
tools dump router isis sr-adjacencies
Description
This command displays IS-IS SR adjacency information.
Parameters
- ip-int-name
-
Specifies the IP interface name. An interface name cannot be in the form of an IP address. Interface names can be any string up to 32 characters long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
- ip-address
-
Specifies the interface’s IP address.
Platforms
All
sr-adjacencies
Syntax
sr-adjacencies [ip-int-name | ip-address] [detail]
sr-adjacencies [remote ip-address] [ detail]
Context
[Tree] (tools>dump>router>ospf3 sr-adjacencies)
[Tree] (tools>dump>router>ospf sr-adjacencies)
Full Context
tools dump router ospf3 sr-adjacencies
tools dump router ospf sr-adjacencies
Description
This command displays OSPFv2 or OSPFv3 SR adjacency information.
Parameters
- ip-int-name
-
Specifies the IP interface name. An interface name cannot be in the form of an IP address. Interface names can be any string up to 32 characters, composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
- ip-address
-
Specifies the interface’s IP address.
Platforms
All
Output
Output Example*A:Dut-C>config>router>ospf3# /tools dump router ospf3 0 sr-adjacencies detail
===============================================================================
Rtr Base OSPFv3 Instance 0 Segment Routing Adjacencies (detail)
Legend:
label stack is ordered from bottom-most to top-most
===============================================================================
-------------------------------------------------------------------------------
Interface DUTC_TO_DUTA.1.0
-------------------------------------------------------------------------------
Nbr RouterID : 10.20.1.1 Nbr State : FULL
Label : 524287 PgID : 9
SID Protection : Enabled Curr Hold Time : 15
Area ID : 0.0.0.1 SR MTU : 1492
Neighbor IP : fe80::200:ff:fe00:1-"DUTC_TO_DUTA.1.0"
LFA Labels : 30004/70005
LFA Next hop : fe80::200:ff:fe00:6-"DUTC_TO_DUTF.1.0"
LFA Glob Itf id: 26 LFA Loc Itf id : 3
-------------------------------------------------------------------------------
Interface DUTC_TO_DUTF.1.0
-------------------------------------------------------------------------------
Nbr RouterID : 10.20.1.6 Nbr State : FULL
Label : 524286 PgID : 10
SID Protection : Enabled Curr Hold Time : 15
Area ID : 0.0.0.1 SR MTU : 1492
Neighbor IP : fe80::200:ff:fe00:6-"DUTC_TO_DUTF.1.0"
LFA Labels : 30003/20005
LFA Next hop : fe80::200:ff:fe00:1-"DUTC_TO_DUTA.1.0"
LFA Glob Itf id: 25 LFA Loc Itf id : 2
-------------------------------------------------------------------------------
No. of SR Adjacencies: 2
===============================================================================
sr-database
sr-database
Syntax
sr-database [sid sid] [prefix ip-address] [nh-type {sr | bgp | rsvp}] [ipv4-unicast | ipv6-unicast] [algo algo-id] [detail]
Context
[Tree] (tools>dump>router>isis sr-database)
Full Context
tools dump router isis sr-database
Description
This command displays IS-IS SR database information.
Parameters
- sid
-
Displays information for the specific segment identifier.
- ip-address
-
Specifies the IP address in dotted decimal notation.
- sr
-
Displays information for SR next-hop route.
- bgp
-
Displays information for BGP next-hop route.
- rsvp
-
Displays information for RSVP next-hop route.
- ipv4-unicast
-
Displays IPv4 unicast parameters.
- ipv6-unicast
-
Displays IPv6 unicast parameters.
- algo algo-id
-
Filters information based on the specific algorithm only.
- detail
-
Displays detailed IS-IS SR database information.
Platforms
All
Output
The following outputs are examples of IS-IS SR database information, and Output fields: IS-IS SR database describes the output fields.
Output Example*A:Dut-E# tools dump router isis sr-database
===============================================================================
Rtr Base ISIS Instance 0 SR Database
===============================================================================
SID Label Prefix Last-act Lev MT RtmPref TtmPref Metric IpNh SrNh
Mtu MtuPrim MtuBk D xL LT Act AdvSystemId SrErr
-------------------------------------------------------------------------------
0 60000 1.0.33.3 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1003 SR_ERR_OK
1 60001 1.0.44.4 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1004 SR_ERR_OK
2 60002 1.0.55.5 Local - - - - - - -
- - - 0 - - +R 0100.2000.1005 SR_ERR_OK
3 60003 1.0.66.6 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1006 SR_ERR_OK
4 60004 1.0.11.1 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1001 SR_ERR_OK
5 60005 1.0.22.2 LfaNhops 1 0 15 11 300 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1002 SR_ERR_OK
6 60006 10.20.1.3 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1003 SR_ERR_OK
7 60007 10.20.1.4 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1004 SR_ERR_OK
8 60008 10.20.1.5 Local - - - - - - -
- - - 0 - - +R 0100.2000.1005 SR_ERR_OK
9 60009 10.20.1.6 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1006 SR_ERR_OK
10 60010 10.20.1.1 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1001 SR_ERR_OK
11 60011 10.20.1.2 LfaNhops 1 0 15 11 300 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1002 SR_ERR_OK
-------------------------------------------------------------------------------
No. of Entries: 12
-------------------------------------------------------------------------------
Lev = route level
IpNh = number of IP next-hops
SrNh = number of SR-tunnel next-hops
D = duplicate pending
xL = exclude from LFA
LT = LFA type (L:LFA, R:RLFA, T:TILFA, n:nodeProtection)
Act = tunnel active state (R:reported, F:failed, +:SR-ack)
===============================================================================
*A:Dut-C# tools dump router isis sr-database detail
===============================================================================
Rtr Base ISIS Instance 0 SR Database
Legend:
label stack is ordered from bottom-most to top-most
===============================================================================
-------------------------------------------------------------------------------
SID 601
-------------------------------------------------------------------------------
Label : 20601 Adv System Id : 0010.0100.1001
Prefix : 1.1.1.1
Route Level : 1 MT Id : 0
Rtm Preference : 15 Ttm Preference : 11
Metric : 10 Last Action : TnlChange
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.1.3.1 N 4 2 19 1 20601 0
-------------------------------------------------------------------------------
SID 602
-------------------------------------------------------------------------------
Label : 20602 Adv System Id : 0010.0100.1002
Prefix : 1.1.1.2
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 10 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.2.3.2 N 5 3 15 1 20602 0
-------------------------------------------------------------------------------
SID 603
-------------------------------------------------------------------------------
Label : 20603 Adv System Id : 0010.0100.1003
Prefix : 1.1.1.3 Type : Local
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
-------------------------------------------------------------------------------
SID 604
-------------------------------------------------------------------------------
Label : 20604 Adv System Id : 0010.0100.1004
Prefix : 1.1.1.4
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 20 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.2.3.2 N 5 3 15 0 20604 0
-------------------------------------------------------------------------------
SID 605
-------------------------------------------------------------------------------
Label : 20605 Adv System Id : 0010.0100.1005
Prefix : 1.1.1.5
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 10 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.3.5.5 N 6 4 17 1 20605 0
-------------------------------------------------------------------------------
SID 606
-------------------------------------------------------------------------------
Label : 20606 Adv System Id : 0010.0100.1006
Prefix : 1.1.1.6
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 20 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.3.5.5 N 6 4 17 0 20606 0
-------------------------------------------------------------------------------
SID 611 Algorithm 128
-------------------------------------------------------------------------------
Label : 20611 Adv System Id : 0010.0100.1001
Prefix : 1.1.1.1
Route Level : 1 MT Id : 0
Rtm Preference : 15 Ttm Preference : 11
Metric : 10 Last Action : TnlChange
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.1.3.1 N 4 2 19 1 20611 0
-------------------------------------------------------------------------------
SID 613
-------------------------------------------------------------------------------
Label : 20613 Adv System Id : 0010.0100.1003
Prefix : 1.1.1.3 Type : Local
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
-------------------------------------------------------------------------------
SID 614 Algorithm 128
-------------------------------------------------------------------------------
Label : 20614 Adv System Id : 0010.0100.1004
Prefix : 1.1.1.4
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 20 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.2.3.2 N 5 3 15 0 20614 0
-------------------------------------------------------------------------------
SID 615 Algorithm 128
-------------------------------------------------------------------------------
Label : 20615 Adv System Id : 0010.0100.1005
Prefix : 1.1.1.5
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 10 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.3.5.5 N 6 4 17 1 20615 0
|
Label |
Description |
|---|---|
|
Label |
The ILM MPLS label corresponding to the SID |
|
Prefix |
The route prefix and mask |
|
Metric |
Interface metric for Level 1 and Level 2; if none are set to 0 |
sr-database
Syntax
sr-database [sid sid] [prefix ip-address] [nh-type {sr | ldp | rsvp}] [algo algo-id] [detail]
Context
[Tree] (tools>dump>router>ospf sr-database)
Full Context
tools dump router ospf sr-database
Description
This command displays OSPFv2 SR database information.
Parameters
- sid
-
Displays information for the specific segment identifier.
- ip-address
-
Specifies the IP address in dotted decimal notation.
- algo-id
-
Displays the OSPFv2 database information for the specified algorithm identifier.
Platforms
All
Output
The following output is an example of OSPFv2 SR database information.
Output Example*A:Dut-C# tools dump router ospf sr-database
===============================================================================
Rtr Base OSPFv2 Instance 0 Segment Routing Database
===============================================================================
SID Label St Type Prefix Stitching
Algo AdvRtr Area Flags FRR
-------------------------------------------------------------------------------
2 100002 +R T1 10.20.1.2/32 -
0 10.20.1.2 0.0.0.0 [NnP ] L(R)
3 100003 +R LT1 10.20.1.3/32 -
0 10.20.1.3 0.0.0.0 [NnP ] -
5 100005 +R T1 10.20.1.5/32 -
0 10.20.1.5 0.0.0.0 [NnP ] L(R)
1282 101282 +R T1 10.20.1.2/32 -
128 10.20.1.2 0.0.0.0 [NnP ] -
1283 101283 +R LT1 10.20.1.3/32 -
128 10.20.1.3 0.0.0.0 [NnP ] -
1285 101285 +R T1 10.20.1.5/32 -
128 10.20.1.5 0.0.0.0 [NnP ] -
-------------------------------------------------------------------------------
No. of Entries: 6
-------------------------------------------------------------------------------
St: R:reported I:incomplete W:wrong N:not reported F:failed
+:SR-ack -:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa T:TiLfa (R):Reported (F):Failed
Ln, Rn, Tn: FRR providing node-protection
===============================================================================
*A:Dut-C# tools dump router ospf sr-database algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Algo 128 Segment Routing Database
===============================================================================
SID Label St Type Prefix Stitching
Algo AdvRtr Area Flags FRR
-------------------------------------------------------------------------------
1282 101282 +R T1 10.20.1.2/32 -
128 10.20.1.2 0.0.0.0 [NnP ] -
1283 101283 +R LT1 10.20.1.3/32 -
128 10.20.1.3 0.0.0.0 [NnP ] -
1285 101285 +R T1 10.20.1.5/32 -
128 10.20.1.5 0.0.0.0 [NnP ] -
-------------------------------------------------------------------------------
No. of Entries: 3
-------------------------------------------------------------------------------
St: R:reported I:incomplete W:wrong N:not reported F:failed
+:SR-ack -:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa T:TiLfa (R):Reported (F):Failed
Ln, Rn, Tn: FRR providing node-protection
===============================================================================sr-database
Syntax
sr-database [sid sid] [prefix ip-address] [nh-type {sr | ldp | rsvp}] [detail]
Context
[Tree] (tools>dump>router>ospf3 sr-database)
Full Context
tools dump router ospf3 sr-database
Description
This command displays OSPFv3 SR database information.
Parameters
- sid
-
Displays information for the specific segment identifier.
- ip-address
-
Specifies the IP address in dotted decimal notation.
Platforms
All
Output
Output ExampleA:Dut-E# tools dump router ospf sr-database
===============================================================================
Rtr Base OSPFv2 Instance 0 Segment Routing Database
===============================================================================
SID Label St Type Prefix Stitching
AdvRtr Area Flags FRR
-------------------------------------------------------------------------------
0 60000 +R T1 1.0.33.3/32 -
10.20.1.3 0.0.0.0 [NnP ] T(R)
1 60001 +R T1 1.0.44.4/32 -
10.20.1.4 0.0.0.0 [NnP ] Tn(R)
2 60002 +R LT1 1.0.55.5/32 -
10.20.1.5 0.0.0.0 [NnP ] -
3 60003 +R T1 1.0.66.6/32 -
10.20.1.6 0.0.0.0 [NnP ] T(R)
4 60004 +R T1 1.0.11.1/32 -
10.20.1.1 0.0.0.0 [NnP ] Tn(R)
5 60005 +R T1 1.0.22.2/32 -
10.20.1.2 0.0.0.0 [NnP ] Tn(R)
6 60006 +R T1 10.20.1.3/32 -
10.20.1.3 0.0.0.0 [NnP ] T(R)
7 60007 +R T1 10.20.1.4/32 -
10.20.1.4 0.0.0.0 [NnP ] Tn(R)
8 60008 +R LT1 10.20.1.5/32 -
10.20.1.5 0.0.0.0 [NnP ] -
9 60009 +R T1 10.20.1.6/32 -
10.20.1.6 0.0.0.0 [NnP ] T(R)
10 60010 +R T1 10.20.1.1/32 -
10.20.1.1 0.0.0.0 [NnP ] Tn(R)
11 60011 +R T1 10.20.1.2/32 -
10.20.1.2 0.0.0.0 [NnP ] Tn(R)
-------------------------------------------------------------------------------
No. of Entries: 12
-------------------------------------------------------------------------------
St: R:reported I:incomplete W:wrong N:not reported F:failed
+:SR-ack -:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa T:TLfa (R):Reported (F):Failed
Rn: RLfa + node-protect Tn: TLfa + node-protect
===============================================================================
*A:Dut-F# tools dump router ospf sr-database detail
====================================================================================
Rtr Base OSPFv2 Instance 0 Segment Routing Database (detail)
====================================================================================
SID Label Sts Prefix Type AdvRtr Area Flags
TnlID FRR
lsId AdvRtr Area Type
------------------------------------------------------------------------------------
0 70000 +R 1.0.33.3/
32 T1 10.20.1.3 0.0.0.1 [NnP ] 2 R(R)
7.16.0.9 10.20.1.2 0.0.0.0 T3
7.0.0.4 10.20.1.3 0.0.0.1 T1 <<<< Best
1 70001 +R 1.0.44.4/
32 T1 10.20.1.4 0.0.0.0 [NnP ] 2 L(R)
7.16.0.5 10.20.1.2 0.0.0.1 T3
7.0.0.4 10.20.1.4 0.0.0.0 T1 <<<< Best
2 70002 +R 1.0.55.5/
32 T1 10.20.1.5 0.0.0.0 [NnP ] 2 R(R)
7.16.0.3 10.20.1.2 0.0.0.1 T3
7.0.0.4 10.20.1.5 0.0.0.0 T1 <<<< Best
3 70003 +R 1.0.66.6/
32 LT1 10.20.1.6 0.0.0.1 [NnP ] 0 -
7.16.0.8 10.20.1.2 0.0.0.0 T3
7.0.0.6 10.20.1.6 0.0.0.1 T1 <<<< Best
4 70004 +R 1.0.11.1/
32 T1 10.20.1.1 0.0.0.1 [NnP ] 2 L(R)
7.16.0.13 10.20.1.2 0.0.0.0 T3
7.0.0.4 10.20.1.1 0.0.0.1 T1 <<<< Best
5 70005 +R 1.0.22.2/
32 T1 10.20.1.2 0.0.0.1 [NnP ] 2 R(R)
7.16.0.11 10.20.1.2 0.0.0.0 T3
7.0.0.6 10.20.1.2 0.0.0.1 T1 <<<< Best
6 70006 +R 10.20.1.3/
32 T1 10.20.1.3 0.0.0.1 [NnP ] 2 R(R)
7.16.0.10 10.20.1.2 0.0.0.0 T3
7.0.0.5 10.20.1.3 0.0.0.1 T1 <<<< Best
7 70007 +R 10.20.1.4/
32 T1 10.20.1.4 0.0.0.0 [NnP ] 2 L(R)
7.16.0.6 10.20.1.2 0.0.0.1 T3
7.0.0.5 10.20.1.4 0.0.0.0 T1 <<<< Best
8 70008 +R 10.20.1.5/
32 T1 10.20.1.5 0.0.0.0 [NnP ] 2 R(R)
7.16.0.4 10.20.1.2 0.0.0.1 T3
7.0.0.5 10.20.1.5 0.0.0.0 T1 <<<< Best
9 70009 +R 10.20.1.6/
32 LT1 10.20.1.6 0.0.0.0 [NnP ] 0 -
7.16.0.2 10.20.1.2 0.0.0.1 T3
7.0.0.7 10.20.1.6 0.0.0.0 T1 <<<< Best
10 70010 +R 10.20.1.1/
32 T1 10.20.1.1 0.0.0.1 [NnP ] 2 L(R)
7.16.0.12 10.20.1.2 0.0.0.0 T3
7.0.0.5 10.20.1.1 0.0.0.1 T1 <<<< Best
11 70011 +R 10.20.1.2/
32 T1 10.20.1.2 0.0.0.0 [NnP ] 2 R(R)
7.16.0.7 10.20.1.2 0.0.0.1 T3
7.0.0.7 10.20.1.2 0.0.0.0 T1 <<<< Best
994 70994 +R 1.0.44.4/
32 T1 10.20.1.5 0.0.0.0 [NnPB ] 0 -
7.16.0.1 10.20.1.5 0.0.0.0 T1 <<<< Best
995 70995 +R 1.0.55.5/
32 T1 10.20.1.4 0.0.0.0 [NnPB ] 0 -
7.16.0.1 10.20.1.4 0.0.0.0 T1 <<<< Best
996 70996 +R 1.0.22.2/
32 LT1 10.20.1.6 0.0.0.1 [NnPB ] 0 -
997 70997 - 1.0.66.6/
32 T1 10.20.1.2 0.0.0.1 [NnPB ] - -
7.16.0.1 10.20.1.2 0.0.0.1 T1 <<<< Best
998 70998 +R 1.0.33.3/
32 T1 10.20.1.1 0.0.0.1 [NnPB ] 0 -
7.16.0.1 10.20.1.1 0.0.0.1 T1 <<<< Best
999 70999 +R 1.0.11.1/
32 T1 10.20.1.3 0.0.0.1 [NnPB ] 0 -
7.16.0.1 10.20.1.3 0.0.0.1 T1 <<<< Best
------------------------------------------------------------------------------------
Sts: R:reported I:incomplete W:wrong N:not reported F:failed +:SR-ack -
:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa (R):Reported (F):Failed
====================================================================================
*A:Dut-F#
sr-label
sr-label
Syntax
sr-label
Context
[Tree] (show>router>bgp sr-label)
Full Context
show router bgp sr-label
Description
This command displays BGP SR label information.
Platforms
All
sr-lfa-coverage
sr-lfa-coverage
Syntax
sr-lfa-coverage [flex-algo {flex-algo-id | all}]
Context
[Tree] (show>router>isis sr-lfa-coverage)
Full Context
show router isis sr-lfa-coverage
Description
This command displays IS-IS SR LFA coverage information. This corresponds to the coverage provided by the various LFA algorithms for SR-ISIS tunnel, SR-TE LSP, and LDP FEC if the fast-reroute backup-sr-tunnel option is enabled. The LFA algorithms activate the backup next hops in the following preference order:
-
TI-LFA
-
LFA
-
R-LFA
Parameters
- flex-algo flex-algo-id
-
Displays SR LFA coverage information for the specified algorithm.
- all
-
Displays all the flexible algorithms that are configured.
Platforms
All
Output
The following output is an example of SR LFA coverage information, and Output fields: IS-IS SR LFA coverage describes the output fields.
Output Example*A:Dut-C>config>router>isis# show router isis 0 sr-lfa-coverage
===============================================================================
Rtr Base ISIS Instance 0 SR LFA Coverage
===============================================================================
MT-ID SidType Level Proto LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
node-sid 4(40%) 6(60%) 0(0%) 10/10(100%)
adj-sid 0(0%) 2(100%) 0(0%) 2/2(100%)
===============================================================================
A:Dut-A# show router isis 0 sr-lfa-coverage flex-algo 128
===============================================================================
Rtr Base ISIS Instance 0 Flex-Algo 128 SR LFA Coverage
===============================================================================
MT-ID SidType Level Proto LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
A:Dut-A# show router isis 0 sr-lfa-coverage flex-algo all
===============================================================================
Rtr Base ISIS Instance 0 Flex-Algo 128 SR LFA Coverage
===============================================================================
MT-ID SidType Level Proto LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
Output fields: IS-IS SR LFA coverage describes the IS-IS SR LFA coverage output fields.
|
Label |
Description |
|---|---|
|
MT-ID |
Displays the MT identification |
|
SidType |
Displays the SID type |
|
Level |
Displays the level |
|
Proto |
Displays the protocol |
|
LFA |
Displays the LFA |
|
RLFA |
Displays the RLFA |
|
TIFLA |
Displays the TI-LFA |
|
Coverage |
Displays the percentage of coverage |
sr-lfa-coverage
Syntax
sr-lfa-coverage [area area-id] [flex-algo { flex-algo-id | all}]
Context
[Tree] (show>router>ospf sr-lfa-coverage)
Full Context
show router ospf sr-lfa-coverage
Description
This command displays the details of the OSPF SR LFA coverage. This corresponds to the coverage provided by the various LFA algorithms for SR-OSPF tunnel, SR-TE LSP, and LDP FEC if fast-reroute backup-sr-tunnel option is enabled. The LFA algorithms activate the backup next hops using the preference order:
-
TI-LFA
-
LFA
-
R-LFA
Parameters
- area area-id
-
Displays all interfaces configured in this area.
- flex-algo flex-algo-id
-
Displays the OSPF SR LFA coverage details for the specified segment routing algorithm.
- flex-algo all
-
Displays the OSPF SR LFA coverage details for all segment routing algorithms.
Platforms
All
Output
The following output is an example of OSPF SR LFA coverage, and Output fields: OSPF SR LFA coverage describes the output fields.
Output Example*A:Dut-C# show router ospf sr-lfa-coverage flex-algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Flex-Algo 128 SR LFA Coverage
===============================================================================
SidType Area LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
node-sid 0.0.0.0 2(100%) 0(0%) 0(0%) 2/2(100%)
===============================================================================
*A:Dut-C#
|
Label |
Description |
|---|---|
|
SidType |
Displays the SID type. |
|
Area |
Displays the OSPF area. |
|
LFA |
Displays the LFA. |
|
RLFA |
Displays the RLFA. |
|
TIFLA |
Displays the TI-LFA. |
|
Coverage |
Displays the percentage of coverage. |
sr-lfa-coverage
Syntax
sr-lfa-coverage [area area-id]
Context
[Tree] (show>router>ospf3 sr-lfa-coverage)
Full Context
show router ospf3 sr-lfa-coverage
Description
This command displays the details of the OSPF SR LFA coverage. This corresponds to the coverage provided by the various LFA algorithms for SR-OSPF tunnel, SR-TE LSP, and LDP FEC if fast-reroute backup-sr-tunnel option is enabled. The LFA algorithms activate the backup next hops using the preference order:
-
TI-LFA
-
LFA
-
R-LFA
Parameters
- area area-id
-
Displays all interfaces configured in this area.
Platforms
All
Output
Output Example*A:Dut-C>config>router>ospf3# show router ospf3 0 sr-lfa-coverage
===============================================================================
Rtr Base OSPFv3 Instance 0 SR LFA Coverage
===============================================================================
SidType Area LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
node-sid 0.0.0.1 4(40%) 6(60%) 0(0%) 10/10(100%)
adj-sid 0.0.0.1 0(0%) 2(100%) 0(0%) 2/2(100%)
===============================================================================
The following table describes the OSPF SR LFA coverage output fields.
|
Label |
Description |
|---|---|
|
SidType |
Displays the SID type. |
|
Area |
Displays the OSPF area. |
|
LFA |
Displays the LFA. |
|
RLFA |
Displays the RLFA. |
|
TIFLA |
Displays the TI-LFA. |
|
Coverage |
Displays the percentage of coverage. |
sr-lfa-info
sr-lfa-info
Syntax
sr-lfa-info [ipv4-unicast | ipv6-unicast | mt mt-id-number] [prefix ip-prefix[/prefix-length]] [algo algo-id] [detail]
sr-lfa-info adjacency [id ip-int-name | ip-address | nbr-system-id] [mt mt-id-number] [assign-type {static | dynamic}] [sid value] [detail]
Context
[Tree] (show>router>isis sr-lfa-info)
Full Context
show router isis sr-lfa-info
Description
This command displays LFA information for an SR-ISIS remote node SID tunnel and SR-ISIS local adjacency SID tunnel.
Parameters
- ipv4-unicast
-
Keyword used to display LFA information of IPv4 unicast SR-ISIS tunnels.
- ipv6-unicast
-
Keyword used to display LFA information of IPv6 unicast SR-ISIS tunnels.
- mt-id-number
-
Filters information based on the specific MT ID value.
- ip-prefix/prefix-length
-
Displays the LFA information for the SR-ISIS tunnel of the specified IP prefix.
- algo-id
-
Filters information based on a specific SR algorithm only.
- detail
-
Keyword to display detailed information.
- adjacency
-
Keyword to display adjacency SID LFA information.
- ip-int-name | ip-address | nbr-system-id
-
Displays the LFA information for the SR-ISIS local adjacency identified as an IP interface, IP address, or neighbor system ID.
- assign-type
-
Keyword to display filters information based on the specific SID assignment type.
- value
-
Displays LFA information for the specified SID value.
Platforms
All
Output
The following outputs are examples of LFA information, and the associated tables describe the output fields:
- SR-ISIS remote node SID tunnel
- SR-ISIS local adjacency SID tunnel
- Output example (adjacency SID with LFA backup using a parallel interface), Output example (adjacency SID with LFA backup not using a parallel interface), Output fields: IS-IS SR LFA adjacency SID information
- Output example (adjacency SID with LFA backup using a parallel interface detail), Output example (adjacency SID with LFA backup not using a parallel interface detail), Output fields: IS-IS SR LFA adjacency SID detailed information
show router isis sr-lfa-info prefix 192.0.2.1/32 algo 253
==========================================================================
Rtr Base ISIS Instance 0 SR LFA Info
==========================================================================
Prefix Algo MT
NextHop
LFA-NextHop LfaType (Pr-Type)
Backup-Node NodeType SID SID-Type
--------------------------------------------------------------------------
192.0.2.1/32 253 0
192.168.13.1
192.168.36.2(L) TI-LFA (Link)
1920.0000.2006 P-Node 524285 Adjacency
1920.0000.2004 TR-Node 524287 Adjacency
1920.0000.2002 TR-Node 524287 Adjacency
1920.0000.2001 Q-Node - -
--------------------------------------------------------------------------
No. of Entries: 1
Pr-Type : Link = linkProtection, Node = nodeProtection
==========================================================================
|
Label |
Description |
|---|---|
|
Rtr Base ISIS Instance 0 SR LFA Info |
|
|
Prefix |
Displays the prefix IP address |
|
Algo |
Displays the algorithm ID |
|
MT |
Displays the Multi-Topology value |
|
NextHop |
Displays the next-hop IP address |
|
LFA-NextHop |
Displays the LFA next-hop IP address |
|
LfaType (Pr-Type) |
Displays the LFA type and protection type |
|
Backup-Node |
Displays the backup node system ID |
|
NodeType |
Displays the node type |
|
SID |
Displays the SID value |
|
SID-Type |
Displays the SID type |
|
No. of Entries |
Displays the total number of entries |
show router isis sr-lfa-info prefix 192.0.2.1/32 algo 253 detail
===============================================================================
Rtr Base ISIS Instance 0 SR LFA Info (detail)
===============================================================================
-------------------------------------------------------------------------------
SR Tunnel Prefix : 192.0.2.1/32
-------------------------------------------------------------------------------
Algorithm : 253
MT : 0
NextHop : 192.168.13.1
LFA-NextHop : 192.168.36.2
LFA-Type : TI-LFA
LFA-Protection : Link Protection
-------------------------------------------------------------------------------
Displaying Backup-Node-Info
-------------------------------------------------------------------------------
Node-count : 4
Node-SysID : 1920.0000.2006
Node-Type : P-Node
SID : 524285
SID-Type : Adjacency
Node-SysID : 1920.0000.2004
Node-Type : TR-Node
SID : 524287
SID-Type : Adjacency
Node-SysID : 1920.0000.2002
Node-Type : TR-Node
SID : 524287
SID-Type : Adjacency
Node-SysID : 1920.0000.2001
Node-Type : Q-Node
SID : -
SID-Type : -
-------------------------------------------------------------------------------
No. of Entries: 1
===============================================================================
|
Label |
Description |
|---|---|
|
Rtr Base ISIS Instance 0 SR LFA Info (detail) |
|
|
SR Tunnel Prefix |
Displays the SR tunnel prefix IP address |
|
Algorithm |
Displays the algorithm ID |
|
MT |
Displays the MT value |
|
NextHop |
Displays the next-hop IP address |
|
LFA-NextHop |
Displays the LFA next-hop IP address |
|
LFA-Type |
Displays the LFA type |
|
LFA-Protection |
Displays the LFA protection type |
|
Displaying Backup-Node-Info |
|
|
Node-count |
Displays the number of nodes |
|
Node-SysID |
Displays the node system ID |
|
Node-Type |
Displays the node type |
|
SID |
Displays the SID value |
|
SID-Type |
Displays the SID type |
|
No. of Entries |
Displays the total number of entries |
*A:Dut-C# /show router isis sr-lfa-info adjacency id "to_Dut-E"
==========================================================================
Rtr Base ISIS Instance 0 SR LFA Info Adjacency
==========================================================================
Interface NbrSysId MT
NbrIp
AdjSID Assign-Type
LFA-NextHop LfaType (Pr-Type)
Backup-Node NodeType SID SID-Type
--------------------------------------------------------------------------
to_Dut-E Dut-E 0
192.168.35.2
524275 Dynamic
192.169.35.2(L) LFA (Link)
to_Dut-E Dut-E 0
fe80::205:feff:fe00:0
524274 Dynamic
fe80::205:feff:fe00:0-"to_Dut-E1"(L) LFA (Link)
--------------------------------------------------------------------------
No. of Entries: 2
Pr-Type : Link = linkProtection, Node = nodeProtection
==========================================================================
/show router isis sr-lfa-info adjacency id "to_Dut-E"
==========================================================================
Rtr Base ISIS Instance 0 SR LFA Info Adjacency
==========================================================================
Interface NbrSysId MT
NbrIp
AdjSID Assign-Type
LFA-NextHop LfaType (Pr-Type)
Backup-Node NodeType SID SID-Type
--------------------------------------------------------------------------
to_Dut-E Dut-E 0
192.168.35.2
524275 Dynamic
192.168.23.1(L) TI-LFA (Link)
1920.0000.2004 PQ-Node 30004 Prefix
1920.0000.2005 Nbr-Node 50005 Prefix
to_Dut-E Dut-E 0
fe80::205:feff:fe00:0
524274 Dynamic
fe80::202:feff:fe00:0-"to_Dut-B"(L) TI-LFA (Link)
1920.0000.2004 PQ-Node 30024 Prefix
1920.0000.2005 Nbr-Node 50025 Prefix
--------------------------------------------------------------------------
No. of Entries: 2
Pr-Type : Link = linkProtection, Node = nodeProtection
==========================================================================|
Label |
Description |
|---|---|
|
Rtr Base ISIS Instance 0 SR LFA Info Adjacency |
|
|
Interface |
Displays the interface name and address |
|
NbrSysId |
Displays the neighbor system ID |
|
MT |
Displays the MT value |
|
NbrIp |
Displays the neighbor IP address |
|
AdjSID |
Displays the adjacency SID value |
|
Assign-type |
Displays the assign type |
|
LFA-NextHop |
Displays the LFA next-hop IP address |
|
Backup-Node |
Displays the backup node |
|
NodeType |
Displays the node type |
|
LfaType (Pr-Type) |
Displays the LFA type and protection type |
|
SID |
Displays the SID |
|
SID-Type |
Displays the SID type |
A:Dut-C# /show router isis sr-lfa-info adjacency id "to_Dut-E" detail
===============================================================================
Rtr Base ISIS Instance 0 SR LFA Info Adjacency (detail)
===============================================================================
-------------------------------------------------------------------------------
Interface : to_Dut-E Neighbor IP: 192.168.35.2
-------------------------------------------------------------------------------
Neighbor : Dut-E
MT : 0
AdjSID : 524275
Assign-Type : Dynamic
LFA-NextHop : 192.169.35.2
LFA-Type : LFA
LFA-Protection : Link Protection
-------------------------------------------------------------------------------
Displaying Backup-Node-Info
-------------------------------------------------------------------------------
Node-count : 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Interface : to_Dut-E Neighbor IP: fe80::205:feff:fe00:0
-------------------------------------------------------------------------------
Neighbor : Dut-E
MT : 0
AdjSID : 524274
Assign-Type : Dynamic
LFA-NextHop : fe80::205:feff:fe00:0-"to_Dut-E1"
LFA-Type : LFA
LFA-Protection : Link Protection
-------------------------------------------------------------------------------
Displaying Backup-Node-Info
-------------------------------------------------------------------------------
Node-count : 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of Entries: 2
===============================================================================show router isis sr-lfa-info adjacency id "to_Dut-E" detail
===============================================================================
Rtr Base ISIS Instance 0 SR LFA Info Adjacency (detail)
===============================================================================
-------------------------------------------------------------------------------
Interface : to_Dut-E Neighbor IP: 192.168.35.2
-------------------------------------------------------------------------------
Neighbor : Dut-E
MT : 0
AdjSID : 524275
Assign-Type : Dynamic
LFA-NextHop : 192.168.23.1
LFA-Type : TI-LFA
LFA-Protection : Link Protection
-------------------------------------------------------------------------------
Displaying Backup-Node-Info
-------------------------------------------------------------------------------
Node-count : 2
Node-SysID : 1920.0000.2004
Node-Type : PQ-Node
SID : 30004
SID-Type : Prefix
Node-SysID : 1920.0000.2005
Node-Type : Nbr-Node
SID : 50005
SID-Type : Prefix
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Interface : to_Dut-E Neighbor IP: fe80::205:feff:fe00:0
-------------------------------------------------------------------------------
Neighbor : Dut-E
MT : 0
AdjSID : 524274
Assign-Type : Dynamic
LFA-NextHop : fe80::202:feff:fe00:0-"to_Dut-B"
LFA-Type : TI-LFA
LFA-Protection : Link Protection
-------------------------------------------------------------------------------
Displaying Backup-Node-Info
-------------------------------------------------------------------------------
Node-count : 2
Node-SysID : 1920.0000.2004
Node-Type : PQ-Node
SID : 30024
SID-Type : Prefix
Node-SysID : 1920.0000.2005
Node-Type : Nbr-Node
SID : 50025
SID-Type : Prefix
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of Entries: 2
===============================================================================|
Label |
Description |
|---|---|
|
Rtr Base ISIS Instance 0 SR LFA Info Adjacency |
|
|
Interface |
Displays the interface name and address |
|
Neighbor IP |
Displays the neighbor IP address |
|
MT |
Displays the MT value |
|
Neighbor |
Displays the neighbor |
|
AdjSID |
Displays the adjacency SID value |
|
Assign-Type |
Displays the assign type |
|
LFA-NextHop |
Displays the LFA next-hop IP address |
| LFA-Type |
Displays the LFA type |
|
LFA-Protection |
Displays the LFA protection type |
|
Displaying Backup-Node-Info |
|
|
Node-count |
Displays the number of nodes |
|
Node-SysID |
Displays the node system ID |
|
Node-Type |
Displays the node type |
|
SID |
Displays the SID value |
|
SID-Type |
Displays the SID type |
|
No. of Entries |
Displays the total number of entries |
sr-policies
sr-policies
Syntax
sr-policies
Context
[Tree] (clear>router>seg-rt sr-policies)
Full Context
clear router segment-routing sr-policies
Description
Commands in this context clear SR policies statistics.
Platforms
All
sr-policies
Syntax
sr-policies
Context
[Tree] (show>router>seg-rt sr-policies)
Full Context
show router segment-routing sr-policies
Description
Commands in this context display SR policy information.
Platforms
All
sr-policies
Syntax
sr-policies
Context
[Tree] (monitor>router>seg-rt sr-policies)
Full Context
monitor router segment-routing sr-policies
Description
Commands in this context monitor Segment Routing SR Policy Statistics.
Platforms
All
sr-policy-ipv4
sr-policy-ipv4
Syntax
sr-policy-ipv4 [rd rd] [color color] [endpoint ip-address]
Context
[Tree] (show>router>bgp>routes sr-policy-ipv4)
Full Context
show router bgp routes sr-policy-ipv4
Description
This command displays BGP SR policy IPv4 routes.
Parameters
- ip-address
-
Specifies the endpoint IPv4 address.
Platforms
All
sr-policy-ipv6
sr-policy-ipv6
Syntax
sr-policy-ipv6 [rd rd] [color color] [endpoint ipv6-address]
sr-policy-ipv6 hunt [rd rd] [color color] [endpoint ipv6-address]
Context
[Tree] (show>router>bgp>routes sr-policy-ipv6)
Full Context
show router bgp routes sr-policy-ipv6
Description
This command displays BGP SR policy IPv6 routes.
Parameters
- ipv6-address
-
Specifies the endpoint IPv6 address, up to 64 characters
Platforms
All
sr-te
sr-te
Syntax
sr-te
Context
[Tree] (clear>router>mpls>lsp>auto-lsp sr-te)
Full Context
clear router mpls lsp auto-lsp sr-te
Description
This command resets and restarts all auto SR-TE LSPs.
Platforms
All
sr-te
Syntax
sr-te
Context
[Tree] (clear>router>mpls>lsp sr-te)
Full Context
clear router mpls lsp sr-te
Description
This command resets and restarts all SR-TE LSPs.
Platforms
All
sr-te-cspf
sr-te-cspf
Syntax
sr-te-cspf [path-computation-method path-computation-method] to ip-address [path path-name] [from ip-address] [include-bitmap bitmap] [exclude-bitmap bitmap] [hop-limit limit] [metric-type-te] [local-sr-protection local-sr-protection] [label-stack-reduction] [max-sr-labels label-stack-size] [exclude-address excl-addr [excl-addr]] [exclude-node excl-node-id [excl-node-id]] [skip-interface interface-name] [metric-type metric-type] [delay-metric-limit delay-metric-limit]
Context
[Tree] (tools>perform>router>mpls sr-te-cspf)
Full Context
tools perform router mpls sr-te-cspf
Description
This command computes and returns one or more SR-TE paths and corresponding label stack to a specific destination router and with the specified constraints.
By default, or when the user specifies the value of ip-to-label for the path-computation-method parameter, MPLS passes the to path and the from parameters to TE-DB, which converts the list of hops into a label stack by scanning the TE database for adjacency and node SID information that belongs to the router or link identified by each hop address. If the conversion is successful, the TE database returns the actual selected hop SIDs plus labels, as well as the configured path hop addresses that were used as the input for this conversion. None of the TE constraint parameters are used in this path computation method.
When the user specifies the value of local-cspf for the path-computation-method parameter, MPLS passes all parameters of the tools command, including the TE constraint parameters. In this case, a full CSPF is run using these parameters.
When the user runs this tools command without specifying a path name, CSPF returns the set of candidate ECMP paths. When the user specifies a path name, CSPF returns a single path, which is selected randomly similar to a configured SR-TE LSP, with the path-computation-method local-cspf command enabled.
Parameters
- to ip-address
-
Specifies the destination address.
- path path-name
-
Specifies the path name, up to 64 characters.
- from ip-address
-
Specifies the originating IP address.
- path-computation-method path-computation-method
-
Specifies the path computation method of the LSP path.
- hop-limit limit
-
Specifies the maximum number of hops for the path.
- exclude-bitmap bitmap
-
Specifies a bit-map of the admin groups that should be excluded in the path computation. Accepted in decimal, hex, or binary.
- include-bitmap bitmap
-
Specifies a bit-map of the admin groups that should be included in the path. Accepted in decimal, hex, or binary.
- metric-type-te
-
Specifies the use of the TE metric to optimize the path. By default, the link IGP metric is used.
This parameter is deprecated. When used, it is automatically translated to metric-type te and an INFO message is displayed that the parameter is deprecated and metric-type te should be used instead.
- local-sr-protection
-
Specifies the local LFA protection desired for the CSPF computed explicit path with adjacency SIDs.
- label-stack-reduction
-
Specifies to apply label stack reduction to the CSPF computed explicit path with adjacency SIDs.
- max-sr-labels label-stack-size
-
Specifies the maximum label stack size of the CSPF computed path with or without label stack reduction.
- exclude-address ip-addr
-
Specifies a list of up to eight IP addresses that should be excluded in the path computation.
- exclude-node excl-node-id
-
Specifies a list of up to eight addresses that should be excluded during the path computation.
- skip-interface interface-name
-
Specifies an interface name, up to 32 characters, that should be skipped during the path computation.
- metric-type metric-type
-
Specifies the metric type.
- delay-metric-limit delay-metric-limit
-
This parameter is valid for metric-type delay only and specifies the upper limit of the delay for a path, in microseconds. If metric-type delay and delay-metric-limitare specified, this command returns the lowest latency path that satisfies the delay-metric-limit. If metric-type delay is specified and the delay-metric-limit is not, the lowest latency path through the network is returned.
Platforms
All
sr-te-lsp
sr-te-lsp
Syntax
sr-te-lsp [lsp-name] [status {up | down}] [detail] path [path-name] [auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte| on-demand-p2p-srte}] [family family]
sr-te-lsp count
sr-te-lsp [lsp-name] [detail] [ auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [family family]
sr-te-lsp [lsp-name] [status {up | down}] [to {ip-address | ipv6-address}] [detail] [auto-lsp { all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [family family]
sr-te-lsp [lsp-name] activepath [ auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [family family]
sr-te-lsp [lsp-name] egress-stats
sr-te-lsp [lsp-name] path [path-name] [ auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] mbb
sr-te-lsp [lsp-name] path [path-name] [auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [detail] [dns]
Context
[Tree] (show>router>mpls sr-te-lsp)
Full Context
show router mpls sr-te-lsp
Description
This command displays SR-TE LSP information.
Parameters
- lsp-name
-
Specifies the SR-TE LSP name, up to 64 characters.
- status
-
Keyword used to filter the output based on the status of the SR-TE LSP.
- detail
-
Keyword used to display detailed information.
- path-name
-
Specifies the SR-TE LSP path name, up to 64 characters.
- auto-lsp
-
Keyword used to display the type of automatic LSP.
- family
-
Displays the family of IP addresses.
- count
-
Keyword used to display the total number of SR-TE LSPs.
- to {ip-address | ipv6-address}
-
Keyword used to display the IPv4 or IPv6 address of the egress router for the LSP.
- egress-stats
-
Keyword used to display the traffic statistics for the specified SR-TE LSP or for all SR-TE LSPs if none is explicitly specified. Traffic statistics are provided for primary path, secondary path if any, and secondary standby paths, if any. Statistics are preserved across switchover only for primary and secondary standby paths.
- mbb
-
Keyword used to display make-before-break (MBB) information.
- activepath
-
Keyword used to display the SR-TE active paths, which are candidate paths selected as the best paths by the SR policy make-before-break (MBB) information.
- dns
-
Keyword used to display reverse DNS resolution of actual and explicit hop information.
Platforms
All
Output
The following outputs are examples of MPLS SR-TE LSP information. The associated tables describe the output fields.
Output ExampleThe following outputs apply to an SR-TE LSP for which the path is computed using the local SR-TE CSPF method.
*A:Dut-C# show router mpls sr-te-lsp "C_F_70000"
===============================================================================
MPLS SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-------------------------------------------------------------------------------
C_F_70000 10.20.1.6 1 N/A Up Up
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "C_F_70000" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : C_F_70000
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.3 To : 10.20.1.6
Adm State : Up Oper State : Up
LSP Up Time : 0d 11:40:44 LSP Down Time : 0d 00:00:00
Transitions : 3 Path Changes : 3
Retry Limit : 0 Retry Timer : 10 sec
Hop Limit : 255 Negotiated MTU : 1484
PathCompMethod : local-cspf
FallbkPathComp : not-applicable
Metric : 1000 Metric Type : igp
Local Sr Protec*: preferred Label Stack Reduction: Enabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 1000
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : C_F_70000
Up Time : 0d 11:40:44
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "C_F_70000" activepath
===============================================================================
MPLS LSP: C_F_70000 (active paths)
===============================================================================
Legend :
# - Manually switched path
#F - Manually forced switched path
===============================================================================
LSP Name : C_F_70000
LSP Id : 26114
Path Name : C_F_70000
Active Path : Primary
To : 10.20.1.6 LSP Type : SR-TE
===============================================================================
*A:Dut-C# tools perform router mpls sr-te-cspf to 10.20.1.6 path "C_F_70000" hop-
limit 3 label-stack-reduction path-computation-method local-cspf max-sr-labels 4
Req CSPF TE path
From: this node To: 10.20.1.6
CSPF TE Path
To: 10.20.1.6
[1] Source Add 10.20.1.3 Cost 4000
Hop 1 -> Label 524242 NH 10.10.2.3 --> 10.10.2.1 (10.20.1.1) Cost 1000 Color 0x0
Hop 2 -> Label 434687 NH :: --> 10.20.1.2 (10.20.1.2) Cost 1000 Color 0x0
Hop 3 -> Label 435087 NH :: --> 10.20.1.4 (10.20.1.4) Cost 1000 Color 0x0
Hop 4 -> Label 435487 NH :: --> 10.20.1.6 (10.20.1.6) Cost 1000 Color 0x0
*A:Dut-C#
*A:Dut-C# tools perform router mpls resignal sr-te-lsp "C_F_70000" path "C_F_70000"
*A:Dut-C#
1 2019/07/03 19:36:37.768 UTC WARNING: MPLS #2014 Base VR 1:
"LSP path C_F_70000::C_F_70000 resignaled as a result of manualResignal MBB"
*A:Dut-C# tools perform router mpls sr-te-cspf to 10.20.1.6 path "C_F_70000" hop-
limit 3 label-stack-reduction path-computation-method local-cspf max-sr-labels 4
Req CSPF TE path
From: this node To: 10.20.1.6
CSPF TE Path
To: 10.20.1.6
[1] Source Add 10.20.1.3 Cost 4000
Hop 1 -> Label 524242 NH 10.10.2.3 --> 10.10.2.1 (10.20.1.1) Cost 1000 Color 0x0
Hop 2 -> Label 434687 NH :: --> 10.20.1.2 (10.20.1.2) Cost 1000 Color 0x0
Hop 3 -> Label 435087 NH :: --> 10.20.1.4 (10.20.1.4) Cost 1000 Color 0x0
Hop 4 -> Label 435487 NH :: --> 10.20.1.6 (10.20.1.6) Cost 1000 Color 0x0
*A:Dut-C#
*A:Dut-C# tools perform router mpls resignal sr-te-lsp "C_F_70000" path "C_F_70000"
*A:Dut-C#
1 2019/07/03 19:36:37.768 UTC WARNING: MPLS #2014 Base VR 1:
"LSP path C_F_70000::C_F_70000 resignaled as a result of manualResignal MBB"
The following show outputs display an LSP with BFD configured to use controlled return path. The following tables describe the MPLS SR-TE LSP detail fields and the MPLS SR-TE LSP path detail fields.
*A:Dut-C# /show router mpls sr-te-lsp detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : to_A_SR_TE
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 3.3.3.3
To : 1.1.1.1
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:00:05 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 2 sec
Hop Limit : 255 Negotiated MTU : 1496
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
ReturnPathLabel : None
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled Override Tunnel ELC : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : path_A
Up Time : 0d 00:00:09
Bandwidth : 0 Mbps
Secondary : path_A2
Down Time : 0d 00:00:50
Bandwidth : 0 Mbps
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : template-1.1.1.1-671747
LSP Type : OneHopP2PSrTe LSP Tunnel ID : 16386
LSP Index : 81921 TTM Tunnel Id : 671747
From : 30.30.2.2
To : 1.1.1.1
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:00:08 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : srte BFD Ping Intvl : N/A
BFD Enable : True BFD Failure-action : None
WaitForUpTimer : 4
ReturnPathLabel : 35002
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled Override Tunnel ELC : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
OriginTemplName : template
Admin Tags : None
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Primary(a) : path_A
Up Time : 0d 00:00:09
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
|
Label |
Description |
|---|---|
|
LSP Name |
The name of the LSP |
|
LSP Type |
The type of the LSP |
| LSP Tunnel ID |
The tunnel ID number for the LSP used in the interaction with PCC/PCE |
|
LSP Index |
The LSP index used for indexing the LSP in the MIB table shared with the RSVP-TE LSP |
|
TTM Tunnel Id |
The tunnel ID number for the tunnel representing the LSP in the tunnel table |
|
From |
The IP address for the ingress router for the LSP |
|
To |
The IP address for the egress router for the LSP |
|
Admin State |
The administrative state of the LSP |
|
Oper State |
The operational state of the LSP |
|
LSP Up Time |
The length of time the LSP has been operational |
|
LSP Down Time |
The amount of time the LSP has been down |
|
Transitions |
The number of transitions that have occurred for the LSP |
|
Path Changes |
The number of times the path has changed |
|
Retry Limit |
The number of attempts that the software makes to reestablish the LSP after it has failed |
|
Retry Timer |
The time, in seconds, for LSP reestablishment attempts after LSP failure |
| Hop Limit |
The maximum number of hops that an LSP can traverse, including the ingress and egress routers |
|
Negotiated MTU |
The size of the maximum transmission unit (MTU) that is negotiated during establishment of the LSP |
|
PathCompMethod |
pce — PCE path computation method is configured local-cspf — Local CSPF path computation method is configured none — No computation method is configured |
| FallbkPathComp |
none — No fallback method is configured local-cspf — Local CSPF fallback is configured |
|
Metric |
The cost of the TE path for the LSP |
|
Local Sr Protection |
The local LFA protection wanted for the CSPF computed explicit path with adjacency SIDs |
|
Label Stack Reduction |
The label stack reduction applied to the CSPF computed explicit path with adjacency SIDs |
|
Load Bal Wt |
The load balance weight value |
| Include Grps |
The included groups. None indicates that no groups are included |
|
Exclude Grps |
The excluded groups. None indicates that no groups are excluded |
|
Egress Stats |
The traffic statistics for the specified SR-TE LSP or for all SR-TE LSPs if none is explicitly specified. Traffic statistics are provided for primary path, secondary path, if any, and secondary standby paths, if any. Statistics are preserved across switch over for primary and secondary standby paths |
|
BFD Template |
The BFD template name |
|
BFD Ping Intvl |
The BFD ping interval |
|
BFD Enable |
The operational state of the BFD on the LSP |
|
BFD Failure-action |
The failure action that is configured for the BFD LSP |
|
WaitForUpTimer |
The BFD wait for up timer value |
|
ReturnPathLabel |
The return path label added to the MPLS label to the bottom of the label stack for S-BFD. With this configured, the S-BFD packet returns to the initiator through the MPLS return path |
|
Revert Timer |
The length of time before a named LSP using the secondary path to revert to the primary path |
| Next Revert In |
The next revert interval |
|
Entropy Label |
The enabled or disabled status for the entropy label |
|
Oper Entropy Label |
Indicates that the entropy label is in use |
|
Negotiated EL |
Indicates if the entropy label is negotiated for the LSP |
| Override Tunnel ELC |
The enabled or disabled status of the override tunnel ELC |
| VPRNAutoBind |
The enabled or disabled status for VRPN autobind |
| IGP Shortcut |
The enabled or disabled status for IGP shortcut |
| BGP Shortcut |
The enabled or disabled status for BGP shortcut |
| IGP LFA |
The enabled or disabled status for IGP LFA |
| BGPTransTun |
The enabled or disabled status for BGP transport tunnels |
| Oper Metric |
The enabled or disabled status of the operational metric |
| PCE Report |
The enabled or disabled status of PCE report |
| PCE Control |
The enabled or disabled status of PCE control |
| Max SR Labels |
The maximum label stack size of the computed path with or without label stack reduction |
| Additional FRR Labels |
The additional FRR labels value that the router is configured to take into account during TI-LFA |
| Path Profile |
The path profile value for the LSP |
| Admin Tags | The administrative tag names. None indicates that there are no tags. |
| Primary (a) |
The preferred path for the LSP |
|
Up Time |
The total time in increments that the LSP path has been operational |
| Bandwidth |
The amount of bandwidth in Mb/s reserved for the LSP path |
| Secondary |
The alternate path that the LSP uses if the primary path is not available |
| Downtime |
The time that the LSP has been down |
| Bandwidth |
The amount of bandwidth in Mb/s reserved for the LSP path |
*A:Dut-C# /show router mpls sr-te-lsp path detail
===============================================================================
MPLS SR-TE LSP
Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE to_A_SR_TE
Path path_A
-------------------------------------------------------------------------------
LSP Name : to_A_SR_TE
Path LSP ID : 3072
From : 3.3.3.3
To : 1.1.1.1
Admin State : Up Oper State : Up
Path Name : path_A
Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:11 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 2 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper SetupPriority: 7
Hold Priority : 0 Oper HoldPriority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None None
Exclude Groups : Oper ExcludeGroups:
None None
Last Resignal : n/a
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1496 Path Trans : 1
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
1.1.1.1(1.1.1.1)(N-SID) Record Label : 19410
BFD Configuration and State
Template : srte Ping Interval : N/A
Enable : True State : up
ReturnPathLabel : 35001
WaitForUpTimer : 4 sec OperWaitForUpTimer: 4 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
-------------------------------------------------------------------------------
LSP SR-TE to_A_SR_TE
Path path_A2
-------------------------------------------------------------------------------
LSP Name : to_A_SR_TE
Path LSP ID : 3074
From : 3.3.3.3
To : 1.1.1.1
Admin State : Up Oper State : Up
Path Name : path_A2
Path Type : Secondary
Path Admin : Up Path Oper : Down
Path Up Time : 0d 00:00:00 Path Down Time : 0d 00:01:53
Retry Limit : 0 Retry Timer : 2 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: N/A
MetricType : igp Oper MetricType : N/A
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : N/A
Hop Limit : 255 Oper HopLimit : N/A
Setup Priority : 7 Oper SetupPriority: N/A
Hold Priority : 0 Oper HoldPriority : N/A
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None N/A
Exclude Groups : Oper ExcludeGroups:
None N/A
Last Resignal : n/a
IGP/TE Metric : N/A Oper Metric : N/A
Oper MTU : N/A Path Trans : 0
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
No Hops Specified
Srlg : Disabled Srlg Disjoint : False
BFD Configuration and State
Template : srte Ping Interval : N/A
Enable : True State : notApplicable
ReturnPathLabel : 35002
WaitForUpTimer : 4 sec OperWaitForUpTimer: 4 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
-------------------------------------------------------------------------------
LSP SR-TE template-1.1.1.1-671747
Path path_A
-------------------------------------------------------------------------------
LSP Name : template-1.1.1.1-671747
Path LSP ID : 14336
From : 30.30.2.2
To : 1.1.1.1
Admin State : Up Oper State : Up
Path Name : path_A
Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:12 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 2 Oper HopLimit : 2
Setup Priority : 7 Oper SetupPriority: 7
Hold Priority : 0 Oper HoldPriority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None None
Exclude Groups : Oper ExcludeGroups:
None None
Last Resignal : n/a
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1496 Path Trans : 1
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
30.30.2.1(1.1.1.1)(A-SID) Record Label : 524282
BFD Configuration and State
Template : None Ping Interval : N/A
Enable : False State : up
ReturnPathLabel : None
WaitForUpTimer : 4 sec OperWaitForUpTimer: 4 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
show router mpls sr-te-lsp path detail dns
===============================================================================
MPLS SR-TE LSP
Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE C_F_65536
Path C_F_1
-------------------------------------------------------------------------------
LSP Name : C_F_65536
Path LSP ID : 13312
From : 10.20.1.3
To : 10.20.1.6
Admin State : Up Oper State : Up
Path Name : C_F_1
Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:27 Path Down Time : 0d 00:00:00
Retry Limit : 10 Retry Timer : 10 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper SetupPriority: 7
Hold Priority : 0 Oper HoldPriority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None None
Exclude Groups : Oper ExcludeGroups:
None None
Last Resignal : n/a
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1488 Path Trans : 1
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
10.20.1.4(S)
Dut-D.nokia.com
-> 10.20.1.5(S)
Dut-E.nokia.com
-> 10.20.1.6(S)
Dut-F.nokia.com
Actual Hops :
10.10.11.4(10.20.1.4)(A-SID) Record Label : 524279
toHUB.Dut-D.nokia.com
(Dut-D.nokia.com)
-> 10.10.6.5(10.20.1.5)(A-SID) Record Label : 524281
toD.Dut-E.nokia.com
(Dut-E.nokia.com)
-> 10.10.10.6(10.20.1.6)(A-SID) Record Label : 524281
toE.Dut-F.nokia.com
(Dut-F.nokia.com)
BFD Configuration and State
Template : None Ping Interval : N/A
Enable : False State : notApplicable
ReturnPathLabel : None
BFD Source Addr : None
WaitForUpTimer : 4 sec OperWaitForUpTimer: 0 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
===============================================================================
5. sr-te (ipV6)
6. Command:
show router mpls sr-te-lsp path detail dns
7. Logs:
===============================================================================
MPLS SR-TE LSP
Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE C_F_65536
Path C_F_1
-------------------------------------------------------------------------------
LSP Name : C_F_65536
Path LSP ID : 60928
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : C_F_1
Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:51:10 Path Down Time : 0d 00:00:00
Retry Limit : 10 Retry Timer : 10 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper SetupPriority: 7
Hold Priority : 0 Oper HoldPriority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None None
Exclude Groups : Oper ExcludeGroups:
None None
Last Resignal : n/a
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1488 Path Trans : 1
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
3ffe::a14:104(S)
Dut-D.nokia.com
-> 3ffe::a14:105(S)
Dut-E.nokia.com
-> 3ffe::a14:106(S)
Dut-F.nokia.com
Actual Hops :
3ffe::a0a:b04
(3ffe::a14:104)(A-SID)
Record Label : 524279
toHUB.Dut-D.nokia.com
(Dut-D.nokia.com)
3ffe::a0a:605
-> (3ffe::a14:105)(A-SID)
Record Label : 524281
toD.Dut-E.nokia.com
(Dut-E.nokia.com)
3ffe::a0a:a06
-> (3ffe::a14:106)(A-SID)
Record Label : 524281
3ffe::a0a:a06
(Dut-F.nokia.com)
BFD Configuration and State
Template : None Ping Interval : N/A
Enable : False State : notApplicable
ReturnPathLabel : None
BFD Source Addr : None
WaitForUpTimer : 4 sec OperWaitForUpTimer: 0 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
|
Label |
Description |
|---|---|
|
LSP Name |
The name of the LSP |
| Path LSP ID |
The path LSP ID |
|
From |
The IP address for the ingress router for the LSP |
|
To |
The IP address for the egress router for the LSP |
|
Admin State |
The administrative state of the LSP |
|
Oper State |
The operational state of the LSP |
|
Path Name |
The name of the LSP path |
|
Path Type |
The type of LSP path |
|
Path Admin |
The administrative state of the LSP path |
|
Path Oper |
The operational state of the LSP path |
|
Path Up Time |
The length of time the LSP path has been operational |
|
Path Down Time |
The length of time the LSP path has been down |
|
Retry Limit |
The number of attempts that the software makes to reestablish the path after it has failed |
|
Retry Timer |
The time, in seconds, for path reestablishment attempts after LSP failure |
| Retry Attempt |
The number of retry attempts |
|
Next Retry In |
The next retry value |
|
PathCompMethod |
The path computation method for the specific LSP pce — PCE path computation method is configured local-cspf — Local CSPF path computation method is configured none — No computation method is configured |
| OperPathCompMethod |
The operational state of the path computation method pce — PCE path computation method is configured local-cspf — Local CSPF path computation method is configured none — No computation method is configured |
|
MetricType |
The cost of the TE path for the specific LSP |
|
Oper MetricType |
The operational state of cost of the TE path |
|
LocalSrProt |
The local LFA protection for the CSPF computed explicit path with adjacency SIDs |
|
Oper LocalSrProt |
The operational state of LFA protection for the CSPF computed explicit path with adjacency SIDs |
|
LabelStackRed |
The label stack reduction applied to the CSPF computed explicit path with adjacency SIDs |
|
Oper LabelStackRed |
The operational state of the label stack reduction applied to the CSPF computed explicit path with adjacency SIDs |
|
Bandwidth |
The amount of bandwidth in Mb/s to be reserved |
|
Oper Bandwidth |
The operational state of the bandwidth |
|
Hop Limit |
The maximum number of hops for the path |
|
Oper HopLimit |
The operational state of the maximum number of hops for the path |
|
Setup Priority |
The setup priority value to use for the path |
|
Oper SetupPriority |
The operational state of the setup priority value for the path |
|
Hold Priority |
The hold priority to use for the path |
|
Oper HoldPriority |
The operational state of the hold priority for the path |
|
PCE Updt ID |
The update ID |
|
PCE Updt State |
The update state |
|
PCE Upd Fail Code |
The update failure code |
| PCE Report |
The enabled or disabled status of PCE report |
|
Oper PCE Report |
The operational state of the PCE report |
|
PCE Control |
The enabled or disabled status of PCE control |
| Oper PCE Control |
The operational state of PCE control |
| Include Groups |
The included groups. None indicates that no groups are included |
| Oper IncludeGroups |
The operational state of the included groups |
| Exclude Groups |
The excluded groups. None indicates that no groups are included |
|
Oper ExcludeGroups |
Oper ExcludeGroups |
|
Last Resignal |
The last resignal time |
|
IGP/TE Metric |
The IGP or TE metric value |
|
Oper Metric |
The operational metric value |
| Oper MTU |
The largest service frame size that can be transmitted to the far-end router without requiring the packet to be fragmented |
|
Path Trans |
The path transmission value |
|
Degraded |
The degraded status |
| Failure Code | The reason code for in-progress MBB value. A value of none indicates that no failure has occurred. |
| Failure Node | The IP address of the node in the LSP path at which the in-progress MBB failed. When no failure has occurred this value is none. |
| Explicit Hops |
The explicit configured hops for an LSP path |
|
Actual Hops |
The actual hops an LSP path takes |
| Record Label |
The record label value |
|
BFD Configuration and State |
|
| Template |
Indicates if the BFD template configured |
| Ping Interval |
The BFD ping interval value |
| Enable |
Indicates if BFD is enabled |
| State |
The state of BFD |
|
ReturnPathLabel |
The return path label to add to the MPLS label on the bottom of the label stack for S-BFD. When configured, the S-BFD packet returns to the initiator through the MPLS return path. |
|
BFD Source Addr |
The BFD source address |
| WaitForUpTimer |
The BFD wait for up timer value |
| OperWaitForUpTimer |
The operational state of the wait for up timer value |
| WaitForUpTmLeft |
The length of time remaining for the wait for up timer |
|
StartFail Rsn |
The start fail RSN value |
The following outputs apply to an SR-TE auto-LSP for which the path is computed by the hop-to-label translation method.
*A:Phoenix 199# show router mpls sr-te-lsp "sr-te-level2-mesh-192.168.48.223-
716805" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : sr-te-level2-mesh-192.168.48.223-716805
LSP Type : MeshP2PSrTe LSP Tunnel ID : 61444
LSP Index : 126979 TTM Tunnel Id : 716805
From : 192.168.48.199 To : 192.168.48.2*
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:02:12 LSP Down Time : 0d 00:00:00
Transitions : 3 Path Changes : 3
Retry Limit : 0 Retry Timer : 30 sec
PathCompMethod : none
FallbkComp : not-applicable
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Enabled
PCE Control : Disabled
Max SR Labels : 8 Additional FRR Labels: 2
Path Profile :
None
Primary(a) : loose-anycast-sid Up Time : 0d 00:02:12
Bandwidth : 0 Mbps
===============================================================================
*A:Phoenix 199# show router mpls sr-te-lsp "sr-te-level2-mesh-192.168.48.223-
716805" path detail
===============================================================================
MPLS SR-TE LSP sr-te-level2-mesh-192.168.48.223-716805 Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
SR-TE LSP sr-te-level2-mesh-192.168.48.223-716805 Path loose-anycast-sid
-------------------------------------------------------------------------------
LSP Name : sr-te-level2-mesh-192.168.48.223-716805
Path LSP ID : 20480
From : 192.168.48.199 To : 192.168.48.223
Admin State : Up Oper State : Up
Path Name : loose-anycast-sid Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 02:30:28 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : local-cspf OperPathCompMethod : local-cspf
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Enabled Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
192.168.48.99(L)
Actual Hops :
192.168.48.99 (192.168.48.185)(N-SID) Record Label : 200099
-> 192.168.48.223 (192.168.48.223)(N-SID) Record Label : 200323
===============================================================================
*A:Phoneix 199# show router mpls sr-te-lsp
- sr-te-lsp [<lsp-name>] [status {up|down}] [detail] path [<path-name>]
[auto-lsp {all|mesh-p2p-srte|one-hop-p2p-srte}]
- sr-te-lsp [<lsp-name>] [detail] [auto-lsp {all|mesh-p2p-srte|
one-hop-p2p-srte}]
- sr-te-lsp [<lsp-name>] [status {up|down}] [to <ip-address>] [detail]
[auto-lsp {all|mesh-p2p-srte|one-hop-p2p-srte}]
<lsp-name> : [64 chars max]
<up|down> : up|down
<ip-address> : a.b.c.d
<detail> : keyword
<path> : keyword
<path-name> : [32 chars max]
<all|mesh-p2p-srte*> : keyword - specify type of auto-lsp
*A:Phoneix 199# show router mpls sr-te-lsp auto-lsp all
===============================================================================
MPLS Auto SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-------------------------------------------------------------------------------
sr-te-level2-mesh-192.168.48.221- 192.168.48.221 61443 N/A Up Up
716804
sr-te-level2-mesh-192.168.48.223- 192.168.48.223 61444 N/A Up Up
716805
-------------------------------------------------------------------------------
LSPs : 2
===============================================================================
*A:Phoneix 199# show router mpls sr-te-lsp auto-lsp mesh-p2p-srte
===============================================================================
MPLS Auto SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-------------------------------------------------------------------------------
sr-te-level2-mesh-192.168.48.221- 192.168.48.221 61443 N/A Up Up
716804
sr-te-level2-mesh-192.168.48.223- 192.168.48.223 61444 N/A Up Up
716805
-------------------------------------------------------------------------------
LSPs : 2
===============================================================================
The following output is an example of SR-TE LSP count statistics.
===============================================================================
MPLS SR-TE LSP Count
===============================================================================
Total IpV4 IpV6
-------------------------------------------------------------------------------
SR-TE LSPs 0 0 0
Mesh SR-TE LSPs 0 0 0
One Hop SR-TE LSPs 0 0 0
PCE Init SR-TE LSPs 0 0 0
===============================================================================
Output fields: MPLS SR-TE LSP describes the MPLS SR-TE LSP count statistics output fields.
|
Label |
Description |
|---|---|
|
LSP Name |
The name of the LSP used in the path. |
|
Adm State |
Down — The path is administratively disabled. Up — The path is administratively enabled. |
|
PathCompMethod |
pce — PCE path computation method is configured. local-cspf — Local CSPF path computation method is configured. |
|
FallbkPathComp |
none — No fallback method is configured. local-cspf — Local CSPF fallback is configured. |
|
Retry Limit |
The number of attempts that the software should make to reestablish the LSP after it has failed. |
|
Hop Limit |
The maximum number of hops that an LSP can traverse, including the ingress and egress routers. |
|
Retry Timer |
The time in seconds, for LSP re-establishment attempts after an LSP failure. |
|
LSP Up Time |
The total time in increments that the LSP path has been operational. |
|
LSP Down Time |
The total time in increments that the LSP path has not been operational. |
|
SR-TE LSPs |
Displays the number of SR-TE LSPs |
|
Mesh SR-TE LSPs |
Displays the number of mesh SR-TE LSPs |
|
One Hop-P2P SR-TE LSPs |
Displays the number of one-hop SR-TE LSPs |
|
PCE Init SR-TE LSPs |
Displays the number of PCE initiated SR-TE LSPs |
The following outputs apply to a router-controlled or to a PCC-controlled SR-TE LSP for which the path is computed using the hop-to-label transition method.
*A:Dut-A# show router mpls sr-te-lsp "srTeRtrControlled" path "1" detail
=======================================================================
MPLS SR-TE LSP srTeRtrControlled Path 1 (Detail)
=======================================================================
Legend :
S - Strict L - Loose
=======================================================================
-----------------------------------------------------------------------
SR-TE LSP srTeRtrControlled Path 1
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled
Path LSP ID : 1024
From : 10.20.1.1 To : 10.20.1.6
Admin State : Up Oper State : Up
Path Name : 1 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:03:19 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : disabled Oper LabelStackRed : disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Inherited Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1484 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
10.20.1.2(S) -> 10.20.1.3(L)
Actual Hops :
10.10.1.2 (10.20.1.2) Record Label : 262143
-> 10.20.1.3 (10.20.1.3) Record Label : 102003
-> 10.20.1.6 (10.20.1.6) Record Label : 103006
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp "srTeRtrControlled" detail
=======================================================================
MPLS SR-TE LSPs (Originating) (Detail)
=======================================================================
-----------------------------------------------------------------------
Type : Originating
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled
LSP Type : SrTeLsp LSP Tunnel ID : 2
LSP Index : 65537 TTM Tunnel Id : 655363
From : 10.20.1.1 To : 10.20.1.6
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:06:09 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1484
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Inherited Max SR Labels : 6
PCE Control : Disabled
Path Profile:
None
Primary(a) : 1 Up Time : 0d 00:06:09
Bandwidth : 0 Mbps
=======================================================================
Outputs with other filters:
---------------------------
*A:Dut-A# show router mpls sr-te-lsp
===============================================================================
MPLS SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-----------------------------------------------------------------------
sr-te1 10.20.1.6 1 N/A Up Up
srTeRtrControlled 10.20.1.6 2 N/A Up Up
-----------------------------------------------------------------------
LSPs : 2
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp path
=======================================================================
MPLS SR-TE LSP Path
=======================================================================
-----------------------------------------------------------------------
LSP Name : sr-te1 To : 10.20.1.6
Adm State : Up Oper State : Up
-----------------------------------------------------------------------
Path Name Type Adm Opr
-----------------------------------------------------------------------
1 Primary Up Up
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled To : 10.20.1.6
Adm State : Up Oper State : Up
-----------------------------------------------------------------------
Path Name Type Adm Opr
-----------------------------------------------------------------------
1 Primary Up Up
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp to 10.20.1.6
=======================================================================
MPLS SRTE LSPs (Originating)
=======================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-----------------------------------------------------------------------
sr-te1 10.20.1.6 1 N/A Up Up
srTeRtrControlled 10.20.1.6 2 N/A Up Up
-----------------------------------------------------------------------
LSPs : 2
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp status up
=======================================================================
MPLS SR-TE LSPs (Originating)
=======================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-----------------------------------------------------------------------
sr-te1 10.20.1.6 1 N/A Up Up
srTeRtrControlled 10.20.1.6 2 N/A Up Up
-----------------------------------------------------------------------
LSPs : 2
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp "srTeRtrControlled" status up detail path "1"
=======================================================================
MPLS SR-TE LSP srTeRtrControlled Path 1 (Detail)
=======================================================================
Legend :
S - Strict L - Loose
=======================================================================
-----------------------------------------------------------------------
SR-TE LSP srTeRtrControlled Path 1
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled
Path LSP ID : 1024
From : 10.20.1.1 To : 10.20.1.6
Admin State : Up Oper State : Up
Path Name : 1 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:07:12 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : none
FallbkPathComp : not-applicable
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Inherited Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1484 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
10.20.1.2(S) -> 10.20.1.3(L)
Actual Hops :
10.10.1.2 (10.20.1.2) Record Label : 262143
-> 10.20.1.3 (10.20.1.3) Record Label : 102003
-> 10.20.1.6 (10.20.1.6) Record Label : 103006
=======================================================================
The following outputs apply to PCE-computed SR-TE LSPs.
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" path detail
===============================================================================
MPLS SR-TE LSP srte_lsp Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
===============================================================================
-------------------------------------------------------------------------------
SR-TE LSP srte_lsp Path fully_loose
-------------------------------------------------------------------------------
LSP Name : srte_lsp
Path LSP ID : 2
From : 10.20.1.2 To : 10.20.1.5
Admin State : Up Oper State : Up
Path Name : fully_loose Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 10:48:05 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Enabled Oper PCE Report : Enabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 20 Oper Metric : 20
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
192.168.2.1 Record Label : 131071
-> 192.168.5.5 Record Label : 131068
===============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : srte_lsp
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.2 To : 10.20.1.5
Adm State : Up Oper State : Up
LSP Up Time : 0d 10:48:17 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : pce
FallbkPathComp : none
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 20
PCE Report : Enabled
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile :
None
Primary(a) : fully_loose Up Time : 0d 10:48:17
Bandwidth : 0 Mbps
===============================================================================
The following outputs apply to a PCE-computed SR-TE LSP when pce-report sr-te is enabled under MPLS.
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" path detail
===============================================================================
MPLS SR-TE LSP srte_lsp Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
===============================================================================
-------------------------------------------------------------------------------
SR-TE LSP srte_lsp Path fully_loose
-------------------------------------------------------------------------------
LSP Name : srte_lsp
Path LSP ID : 2
From : 10.20.1.2 To : 10.20.1.5
Admin State : Up Oper State : Up
Path Name : fully_loose Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 10:51:47 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod: : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Inherited Oper PCE Report : Enabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 20 Oper Metric : 20
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
192.168.2.1 Record Label : 131071
-> 192.168.5.5 Record Label : 131068
===============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : srte_lsp
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.2 To : 10.20.1.5
Adm State : Up Oper State : Up
LSP Up Time : 0d 10:52:16 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : pce
FallbkPathComp : none
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 20
PCE Report : Inherited
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile :
None
Primary(a) : fully_loose Up Time : 0d 10:52:16
Bandwidth : 0 Mbps
===============================================================================
The following outputs apply to PCE-controlled SR-TE LSPs.
*A:Dut-B>config>router>pcep>pcc# /show router mpls sr-te-lsp "srte_lsp" path detail
=============================================================================
MPLS SR-TE LSP srte_lsp Path (Detail)
=============================================================================
Legend :
S - Strict L - Loose
=============================================================================
-----------------------------------------------------------------------------
SR-TE LSP srte_lsp Path fully_loose
-----------------------------------------------------------------------------
LSP Name : srte_lsp
Path LSP ID : 2
From : 10.20.1.2 To : 10.20.1.5
Admin State : Up Oper State : Up
Path Name : fully_loose Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:07 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod: : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Enabled Oper PCE Report : Enabled
PCE Control : Enabled Oper PCE Control : Enabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 20 Oper Metric : 20
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
192.168.2.1 Record Label : 131071
-> 192.168.5.5 Record Label : 131068
=============================================================================
*A:Dut-B>config>router>pcep>pcc# /show router mpls sr-te-lsp "srte_lsp" detail
=============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
=============================================================================
-----------------------------------------------------------------------------
Type : Originating
-----------------------------------------------------------------------------
LSP Name : srte_lsp
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.2 To : 10.20.1.5
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:01:38 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : pce
FallbkPathComp : none
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 20
PCE Report : Enabled
PCE Control : Enabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile :
None
Primary(a) : fully_loose Up Time : 0d 00:01:38
Bandwidth : 0 Mbps
=============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router pcep pcc lsp-db
=============================================================================
PCEP Path Computation Client (PCC) LSP Update Info
=============================================================================
PCEP-specific LSP ID: 3
LSP ID : 2 LSP Type : seg-rt
Tunnel ID : 1 Extended Tunnel Id : 10.20.1.2
LSP Name : srte_lsp::fully_loose
Source Address : 10.20.1.2 Destination Address : 10.20.1.5
LSP Delegated : True Delegate PCE Address: 10.20.1.24
Oper Status : active
=============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" path
=============================================================================
MPLS SR-TE LSP srte_lsp Path
=============================================================================
-----------------------------------------------------------------------------
LSP Name : srte_lsp To : 10.20.1.5
Adm State : Up Oper State : Up
-----------------------------------------------------------------------------
Path Name Type Adm Opr
-----------------------------------------------------------------------------
fully_loose Primary Up Up
=============================================================================
The following output applies to SR-TE LSP path statistics.
*A:Dut-C# show router mpls sr-te-lsp path family ipv6 status up
===============================================================================
MPLS SR-TE LSP Path
===============================================================================
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
To : 3ffe::a14:106
Adm State : Up Oper State : Up
-------------------------------------------------------------------------------
Path Name Type Adm Opr
-------------------------------------------------------------------------------
pe1_pe2 Primary Up Up
pe1_pe2_Stby Standby Up Up
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106"
===============================================================================
MPLS SR-TE LSPs (Originating)
===============================================================================
LSP Name Tun Protect Adm Opr
To Id Path
-------------------------------------------------------------------------------
3ffe::a14:106 1 N/A Up Up
3ffe::a14:106
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 3ffe::a14:103
To : 3ffe::a14:106
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:05:11 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : pe1_pe2
Up Time : 0d 00:05:13
Bandwidth : 0 Mbps
Secondary : pe1_pe2_Sec
Down Time : 0d 00:01:23
Bandwidth : 0 Mbps
Standby : pe1_pe2_Stby
Up Time : 0d 00:01:09
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" path
===============================================================================
MPLS SR-TE LSP 3ffe::a14:106 Path
===============================================================================
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
To : 3ffe::a14:106
Adm State : Up Oper State : Up
-------------------------------------------------------------------------------
Path Name Type Adm Opr
-------------------------------------------------------------------------------
pe1_pe2 Primary Up Up
pe1_pe2_Sec Secondary Up Dwn
pe1_pe2_Stby Standby Up Up
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" path detail
===============================================================================
MPLS SR-TE LSP 3ffe::a14:106 Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59904
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:09:24 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priori*: 7 Oper Setup Priority : 7
Hold Priority: 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None None
Exclude Grou*: Oper Exclude Groups :
None None
Last Resignal: n/a
IGP/TE Metric: 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:101(L)
-> 3ffe::a14:106(L)
Actual Hops :
3ffe::a14:101
(3ffe::a14:101)(N-SID)
Record Label : 454488
3ffe::a14:106
-> (3ffe::a14:106)(N-SID)
Record Label : 424493
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2_Sec
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59906
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2_Sec Path Type : Secondary
Path Admin : Up Path Oper : Down
Path Up Time : 0d 00:00:00 Path Down Time : 0d 00:05:35
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : N/A
MetricType : igp Oper MetricType : N/A
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed: Disabled Oper LabelStackRed : N/A
Bandwidth : No Reservation Oper Bandwidth : N/A
Hop Limit : 255 Oper HopLimit : N/A
Setup Priori*: 7 Oper Setup Priority : N/A
Hold Priority: 0 Oper Hold Priority : N/A
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None N/A
Exclude Grou*: Oper Exclude Groups :
None N/A
Last Resignal: n/a
IGP/TE Metric: N/A Oper Metric : N/A
Oper MTU : N/A Path Trans : 2
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:102(L)
-> 3ffe::a14:106(L)
Actual Hops :
No Hops Specified
Srlg : Disabled Srlg Disjoint : False
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2_Stby
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59908
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2_Stby Path Type : Standby
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:05:21 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priori*: 7 Oper Setup Priority : 7
Hold Priority: 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None None
Exclude Grou*: Oper Exclude Groups :
None None
Last Resignal: n/a
IGP/TE Metric: 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:102(L)
-> 3ffe::a14:106(L)
Actual Hops :
3ffe::a14:102
(3ffe::a14:102)(N-SID)
Record Label : 454489
3ffe::a14:106
-> (3ffe::a14:106)(N-SID)
Record Label : 439493
Srlg : Disabled Srlg Disjoint : False
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" status up detail path "pe1_pe2"
family ipv6
===============================================================================
MPLS SR-TE LSP 3ffe::a14:106 Path pe1_pe2 (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59904
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:16:20 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priori*: 7 Oper Setup Priority : 7
Hold Priority: 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None None
Exclude Grou*: Oper Exclude Groups :
None None
Last Resignal: n/a
IGP/TE Metric: 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:101(L)
-> 3ffe::a14:106(L)
Actual Hops :
3ffe::a14:101
(3ffe::a14:101)(N-SID)
Record Label : 454488
3ffe::a14:106
-> (3ffe::a14:106)(N-SID)
Record Label : 424493
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" activepath
===============================================================================
MPLS LSP: 3ffe::a14:106 (active paths)
===============================================================================
Legend :
# - Manually switched path
#F - Manually forced switched path
===============================================================================
LSP Name : 3ffe::a14:106
LSP Id : 59904
Path Name : pe1_pe2
Active Path : Primary
To : 3ffe::a14:106
LSP Type : SR-TE
===============================================================================
*A:Dut-C>config>router>mpls# show router mpls sr-te-lsp "3ffe::a14:106" egress-stats
===============================================================================
SR-TE LSP Egress Statistics
===============================================================================
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
-------------------------------------------------------------------------------
Admin State : Up
Path Name : pe1_pe2
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Path Name : pe1_pe2_Sec
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Path Name : pe1_pe2_Stby
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Total for all paths
Tot.Aggr Pkts : 0 Tot.Aggr Octets : 0
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" to 3ffe::a14:106 detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 3ffe::a14:103
To : 3ffe::a14:106
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:50:36 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : pe1_pe2
Up Time : 0d 00:50:39
Bandwidth : 0 Mbps
Secondary : pe1_pe2_Sec
Down Time : 0d 00:46:48
Bandwidth : 0 Mbps
Standby : pe1_pe2_Stby
Up Time : 0d 00:46:34
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
The following output applies to SR-TE LSP egress statistics.
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "lsp1" egress-stats
===============================================================================
SR-TE LSP Egress Statistics
===============================================================================
-------------------------------------------------------------------------------
LSP Name : lsp1
-------------------------------------------------------------------------------
Admin State : Up
Path Name : p1
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Path Name : p2
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Total for all paths
Tot.Aggr Pkts : 0 Tot.Aggr Octets : 0
Packet Rate pps : 0 Bit Rate Mbps : 0
===============================================================================
Output fields: MPLS SR-TE LSP egress statistics describes the MPLS SR-TE LSP egress statistics output fields.
|
Label |
Description |
|---|---|
|
LSP Name |
The name of the LSP for which the statistics are provided |
|
Admin State |
The administrative state of the LSP |
|
Path Name |
The path name of the LSP |
|
StatsOperState |
Indicates whether the system is able to allocate a statistical index to that specific path |
|
Aggregate Pkts |
The number of packets recorded by the statistical index for that path |
|
Aggregate Octets |
The number of octets recorded by the statistical index for that path |
|
Tot.Aggr Pkts |
The sum of packets over all paths of the LSP |
|
Tot.Aggr Octets |
The sum of octets over all paths of the LSP |
|
Packet Rate |
The packet rate for the LSP (across all paths, for all FCs in/out-of profile) expressed in packets per second |
|
Bit Rate |
The bit rate for the LSP (across all paths, for all FCs in/out-of profile) expressed in Mb/s |
sr-te-lsp-egress-stats
sr-te-lsp-egress-stats
Syntax
sr-te-lsp-egress-stats lsp-name
Context
[Tree] (clear>router>mpls sr-te-lsp-egress-stats)
Full Context
clear router mpls sr-te-lsp-egress-stats
Description
This command clears or resets the egress statistics for MPLS SR-TE LSP.
Parameters
- lsp-name
-
Specifies the LSP to clear, up to 64 characters.
Platforms
All
sr-te-lsp-egress-stats
Syntax
sr-te-lsp-egress-stats lsp lsp-name [interval seconds] [repeat repeat] [ absolute| rate] [bits ]
Context
[Tree] (monitor>router>mpls sr-te-lsp-egress-stats)
Full Context
monitor router mpls sr-te-lsp-egress-stats
Description
This command monitors MPLS SR-TE LSP Egress Statistics.
Parameters
- lsp-name
-
Specifies the LSP name.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
- bits
-
Displays output value in bits.
Platforms
All
src-access-list
src-access-list
Syntax
src-access-list [list-name]
Context
[Tree] (show>system>security>snmp src-access-list)
Full Context
show system security snmp src-access-list
Description
This command displays source access lists and the hosts for each. Including the list-name parameter modifies the output show only the specified src-access-list.
Platforms
All
Output
The following output is an example of SR access list information.
Output fields: source access list describes the source access list output fields.
Output ExampleA:ALA-1# show system security snmp src-access-list
=============================================================================
Source Access Lists
=============================================================================
List Name
HostName Host Address
-----------------------------------------------------------------------------
L1
H1 10.100.100.1
H2 10.100.100.2
L2
HA 10.100.101.1
HB 10.100.101.2
-----------------------------------------------------------------------------
Total Access Lists: 2
=============================================================================
A:ALA-1#
A:ALA-1# show system security snmp src-access-list L1
=============================================================================
Source Access Lists
=============================================================================
List Name
HostName Host Address
-----------------------------------------------------------------------------
L1
H1 10.100.100.1
H2 10.100.100.2
-----------------------------------------------------------------------------
Total Access Lists: 1
=============================================================================
A:ALA-1#
|
Label |
Description |
|---|---|
|
List Name |
Displays the name of the src-access-list. |
|
Host Name |
Displays the name of the src-host. |
|
Host Address |
Displays the IP address of the src-host. |
|
Total Access Lists |
Displays the total number of source access lists. |
src-bmac-lsb
src-bmac-lsb
Syntax
src-bmac-lsb
Context
[Tree] (tools>dump>redundancy src-bmac-lsb)
Full Context
tools dump redundancy src-bmac-lsb
Description
This command dumps PBB source Backbone MAC address LSB information.
Platforms
All
srlg-database
srlg-database
Syntax
srlg-database [router-id ip-address] [interface ip-address]
Context
[Tree] (show>router>mpls srlg-database)
Full Context
show router mpls srlg-database
Description
This command displays MPLS SRLG database information.
Parameters
- router-id ip-address
-
Specifies a 32-bit integer uniquely identifying the router in the Autonomous System. By convention to ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router. The router-id can be either the local one or some remote router.
- interface ip-address
-
Specifies the IP address of the interface.
Platforms
All
srlg-group
srlg-group
Syntax
srlg-group [name]
Context
[Tree] (show>router>if-attribute srlg-group)
Full Context
show router if-attribute srlg-group
Description
This command displays SRLG statistics.
Parameters
- name
-
Displays entries that are associated with the specified SRLG name, up to 32 characters.
Platforms
All
Output
The following output is an example of SRLG statistics, and Output fields: SRLG describes the fields.
Output ExampleB:CORE2# show router if-attribute srlg-group
==================================================
Interface Srlg Groups
==================================================
Group Name Group Value Penalty Weight
--------------------------------------------------
1 1 100
2 2 200
3 3 300
--------------------------------------------------
No. of Groups: 3
==================================================
B:CORE2#
|
Label |
Description |
|---|---|
|
Group Name |
The name of the SRLG |
|
Group Value |
The integer value of the SRLG |
|
Penalty Weight |
The penalty weight that is assigned to the SRLG |
|
No. of Groups |
The total number of displayed SRLGs |
srrp
srrp
Syntax
srrp
Context
[Tree] (clear>router srrp)
Full Context
clear router srrp
Description
Commands in this context clear and reset SRRP virtual router instances.
Platforms
All
srrp
Syntax
srrp [srrp-id [detail]]
Context
[Tree] (show srrp)
Full Context
show srrp
Description
This command displays information related to the SRRP.
Parameters
- srrp-id
-
Specifies the SRRP ID.
- detail
-
Displays detailed information.
Platforms
All
srrp-sync-database
srrp-sync-database
Syntax
srrp-sync-database [instance instance-id] [ peer ip-address]
Context
[Tree] (tools>dump>redundancy>multi-chassis srrp-sync-database)
Full Context
tools dump redundancy multi-chassis srrp-sync-database
Description
This command dumps SRRP database information and applies to the 7450 ESS.
Parameters
- ip-address
-
Specifies the peer’s IP address.
- instance-id
-
Dumps information for the specified Subscriber Router Redundancy Protocol instance configured on this system.
Platforms
All
ssh
ssh
Syntax
ssh [detail | server-lists | client-lists | server-public-keys]
Context
[Tree] (show>system>security ssh)
Full Context
show system security ssh
Description
This command displays all SSH sessions and the SSH status and fingerprint. The type of SSH application (CLI, SCP, SFTP, or NETCONF) is indicated for each SSH connection.
Parameters
- detail
-
Keyword to display detailed information.
- server-lists
-
Keyword to display the lists of cipher, MAC, KEX, and host key algorithms allowed by the SSH server.
- client-lists
-
Keyword to display the lists of cipher, MAC, KEX, and host key algorithms allowed by the SSH client.
- server-public-keys
-
Keyword to display the SSH server public keys.
Platforms
All
Output
The following outputs are examples of SSH information, and Output fields: ssh describes the output fields.
Output example (show system security ssh)===============================================================================
SSH Server
===============================================================================
Administrative State : Enabled
Operational State : Up
Preserve Key : Disabled
Key-re-exchange : 60 minutes / 1024 MB
SSH Protocol Version 2 : Enabled
Host Key Fingerprints :
RSA : MD5:51:02:1d:28:0e:b3:49:f9:71:79:2e:67:a3:25:55:74
SHA256:pYOhLriNg0sXo+Ekh3cl7OsrlteLLjV/MKCGxbQSuXQ
ECDSA-SHA2-NISTP256 : MD5:d8:63:f5:9a:01:0f:24:4e:26:06:ab:a4:05:08:fb:52
SHA256:LZ/CHBwn+zCNyLGtTS45UJd8xvjq75hgsnQHvQRvpkU
ECDSA-SHA2-NISTP521 : MD5:fa:7d:9f:16:a7:e1:17:89:52:0d:d3:bc:0d:c8:1d:ef
SHA256:VWiLxOjcNivVYvJIVc3W2oMNUAT0vMl9ckQsnbXF4+I
-------------------------------------------------------------------------------
Connection ConnectionID
Username ConnectionStatus
RouterInstance Key-re-exchange
Version KEX
Cipher
MAC
HostKey
SessionID ChannelID ServerName ChannelStatus
-------------------------------------------------------------------------------
192.168.135.227 23
admin connected
management 60 minutes / 1024 MB
SSHv2 ecdh-sha2-nistp256
aes128-ctr
hmac-sha2-256
ecdsa-sha2-nistp256
23 0 cli connected
-------------------------------------------------------------------------------
Number of SSH connections : 1
Number of SSH sessions : 1
=======================================================
===============================================================================
SSH Server Global
===============================================================================
Administrative State : Enabled
Operational State : Up
Preserve Key : Disabled
Key-re-exchange : 60 minutes / 1024 MB
SSH Protocol Version 2 : Enabled
Host Key Fingerprints :
RSA : MD5:51:02:1d:28:0e:b3:49:f9:71:79:2e:67:a3:25:55:74
SHA256:pYOhLriNg0sXo+Ekh3cl7OsrlteLLjV/MKCGxbQSuXQ
ECDSA-SHA2-NISTP256 : MD5:d8:63:f5:9a:01:0f:24:4e:26:06:ab:a4:05:08:fb:52
SHA256:LZ/CHBwn+zCNyLGtTS45UJd8xvjq75hgsnQHvQRvpkU
ECDSA-SHA2-NISTP521 : MD5:fa:7d:9f:16:a7:e1:17:89:52:0d:d3:bc:0d:c8:1d:ef
SHA256:VWiLxOjcNivVYvJIVc3W2oMNUAT0vMl9ckQsnbXF4+I
===============================================================================
SSH Server Router Instance [Base]
===============================================================================
Access allowed : Allowed
-------------------------------------------------------------------------------
Connection ConnectionID
Username ConnectionStatus
Key-re-exchange
Version KEX
Cipher
MAC
HostKey
SessionID ChannelID ServerName ChannelStatus
-------------------------------------------------------------------------------
No entries found
===============================================================================
SSH Server Router Instance [management]
===============================================================================
Access allowed : Allowed
-------------------------------------------------------------------------------
Connection ConnectionID
Username ConnectionStatus
Key-re-exchange
Version KEX
Cipher
MAC
HostKey
SessionID ChannelID ServerName ChannelStatus
-------------------------------------------------------------------------------
192.168.135.227 23
admin connected
60 minutes / 1024 MB
SSHv2 ecdh-sha2-nistp256
aes128-ctr
hmac-sha2-256
ecdsa-sha2-nistp256
23 0 cli connected
-------------------------------------------------------------------------------
Number of SSH connections : 1
Number of SSH sessions : 1
===============================================================================
===============================================================================
SSH Server configurable algorithm lists
===============================================================================
SSHv2 Cipher List : aes256-ctr
aes192-ctr
aes128-ctr
aes128-cbc
3des-cbc
aes192-cbc
aes256-cbc
-------------------------------------------------------------------------------
SSHv2 MAC List : hmac-sha2-512
hmac-sha2-256
hmac-sha1
hmac-sha1-96
hmac-md5
hmac-md5-96
-------------------------------------------------------------------------------
SSHv2 KEX List : ecdh-sha2-nistp521
ecdh-sha2-nistp384
ecdh-sha2-nistp256
diffie-hellman-group16-sha512
diffie-hellman-group14-sha256
diffie-hellman-group14-sha1
diffie-hellman-group-exchange-sha1
diffie-hellman-group1-sha1
-------------------------------------------------------------------------------
SSHv2 Host Key List : ecdsa-sha2-nistp521
ecdsa-sha2-nistp256
rsa-sha2-512
rsa-sha2-256
ssh-rsa
===============================================================================
===============================================================================
SSH Client configurable algorithm lists
===============================================================================
SSHv2 Cipher List : aes256-ctr
aes192-ctr
aes128-ctr
aes128-cbc
3des-cbc
aes192-cbc
aes256-cbc
-------------------------------------------------------------------------------
SSHv2 MAC List : hmac-sha2-512
hmac-sha2-256
hmac-sha1
hmac-sha1-96
hmac-md5
hmac-md5-96
-------------------------------------------------------------------------------
SSHv2 KEX List : ecdh-sha2-nistp521
ecdh-sha2-nistp384
ecdh-sha2-nistp256
diffie-hellman-group16-sha512
diffie-hellman-group14-sha256
diffie-hellman-group14-sha1
diffie-hellman-group-exchange-sha1
diffie-hellman-group1-sha1
-------------------------------------------------------------------------------
SSHv2 Host Key List : ecdsa-sha2-nistp521
ecdsa-sha2-nistp384
ecdsa-sha2-nistp256
rsa-sha2-512
rsa-sha2-256
ssh-ed25519
ssh-rsa
===============================================================================
===============================================================================
SSH Server Public Keys
===============================================================================
ECDSA-SHA2-NISTP521 : AAAAE2VjZHNhLXNoYTItbmlzdHA1MjEAAAAIbmlzdHA1MjEAAAC
FBAC/KEjM6eNmM6ltKRBqhhimf9VL/
l5OXhltfKKmJ28iWh7D7hFQGlVwW1UbvrZkBuuAu4LKobEpxGSx
yWnEZBIKZADU9ygImM94ZsznyVRUlK26KhwoglMHfeahsXJLSVt
MbAB7AYLfbFBudboPDUOHAAxD4I+hGgo/V8JXY5SmJ22jEA==
ECDSA-SHA2-NISTP256 : AAAAE2VjZHNhLXNoYTItbmlzdHAyNTYAAAAIbmlzdHAyNTYAAAB
BBGvOLOnLcBuknK4GVzmh35WSoLZf8WxCvteB1U8ltwvECqSsoP
lq3sPhwxaFSHD43HLIzO/848jihVjGqb3owvY=
SSH-RSA : AAAAB3NzaC1yc2EAAAADAQABAAABAQDxOTlF36RZBvMlQ1eM+Hx
exDUA/DRxdXs+S9IrEhqBczbt9/bNn/
8UmzRS5rcvT2Lo3F5x8OUe7VvFJmxDXZjTSWvxS3RqkDA6DR+O5
4aWv+m5ZLSDWCeDRUydDPuYfTL6QTHEiL6SC+Q2BTfso3YYi6Yr
a0lIhcbiuAnphClBJc9s3t2D/C5rOn2/
TjGjOOtikKnpCrJzDdGYQnev2+0O6hTNCx3R4f171HYSZUQP8AU
csasQMxOYHDKk5DJH8zSN/JPpsz2lQnNRIH4/
xY+KQzYAsvkqSO6RWienXnqBo4H59WeeCgR3WKRX7eRUVaAOkcR
ghmLqnS8fIZMmFRyz
===============================================================================
|
Label |
Description |
|---|---|
|
Administrative State |
Enabled — The administrative state of the SSH server is enabled Disabled — The administrative state of the SSH server is disabled |
|
Operational State |
Up — The operational state of the SSH server is up Down — The operational state of the SSH server is down |
|
Preserve Key |
Enabled — preserve-key is enabled Disabled — preserve-key is disabled |
|
Key-re-exchange |
The maximum amount of time and the maximum number of megabytes to be transmitted before a key re-exchange is initiated by the server |
|
SSH Protocol Version 2 |
Enabled — SSH2 is enabled Disabled — SSH2 is disabled |
|
Host Key Fingerprints |
The key fingerprint is the server identity. If a client attempts and fails to verify the key fingerprint of the server, the client session is disconnected. |
|
Connection |
The IP address of the connected routers (remote client) |
|
ConnectionID |
The connection ID |
|
Username |
The name of the user |
|
ConnectionStatus |
The connection status |
|
Version |
The SSH version |
|
KEX |
KEX algorithm negotiated between SR OS SSH server and SSH client |
|
Cipher |
Cipher algorithm negotiated between SR OS SSH server and SSH client |
|
MAC |
MAC algorithm negotiated between SR OS SSH server and SSH client |
|
HostKey |
Host key algorithm negotiated between SR OS SSH server and SSH client |
|
SessionID |
The session ID |
|
ChannelID |
The channel ID |
|
ServerName |
The server name |
|
ChannelStatus |
The channel status |
| Number of SSH connections | The total number of SSH connections |
|
Number of SSH sessions |
The total number of active SSH sessions |
ssid
ssid
Syntax
ssid
Context
[Tree] (show>subscr-mgmt>wlan-gw ssid)
Full Context
show subscriber-mgmt wlan-gw ssid
Description
This command displays SSID information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
ssm-translate
ssm-translate
Syntax
ssm-translate
ssm-translate interface interface-name
Context
[Tree] (show>router>igmp ssm-translate)
Full Context
show router igmp ssm-translate
Description
This command displays IGMP SSM translate configuration information.
Parameters
- interface-name
-
Specifies the IP interface name, up to 32 characters.
Platforms
All
Output
The following output is an example of SSM translate information. Output fields: IGMP provides IGMP field descriptions.
Output Example=================================================================
IGMP SSM Translate Entries
=================================================================
Group Range Source Interface
-----------------------------------------------------------------
<239.1.1.1 - 239.1.1.2> 10.1.1.1 -
<239.1.1.1 - 239.1.1.5> 00.1.1.2 ies-abc
-----------------------------------------------------------------
|
Label |
Description |
|---|---|
|
Group Range |
The address ranges of the multicast groups for which this router can be an RP. |
|
Source |
The unicast address that sends data on an interface. |
|
SSM Translate Entries |
The total number of SSM translate entries. |
ssm-translate
Syntax
ssm-translate
ssm-translate interface interface-name
Context
[Tree] (show>router>mld ssm-translate)
Full Context
show router mld ssm-translate
Description
This command displays MLD SSM translate configuration information.
Parameters
- interface-name
-
Specifies the IP interface name, up to 32 characters.
Platforms
All
Output
MLD Interface Output
The following table provides MLD field descriptions.
|
Label |
Description |
|---|---|
|
Start Address End Address |
The address ranges of the multicast groups for which this router can be an RP. |
|
Source Address |
The unicast address that sends data on an interface. |
|
Interface |
The interface name. |
|
SSM Translate Entries |
The total number of SSM translate entries. |
*A:ALA-BA# show router mld static
===============================================================================
MLD SSM Translate Entries
===============================================================================
Start Address : ff0e::db8:9
End Address : ff0e::db8:c
Source Address : 2001:db8::1
Start Address : ff04:db8:2
End Address : ff04:db8:10
Source Address : 2001:db8:3:4:5:6:7:8
Interface : lax-vls
Start Address : ff0e:db8:db8:9
End Address : ff0e:db8:db8:c
Source Address : 2001:db8::1
Interface : lax-vls
-------------------------------------------------------------------------------
SSM Translate Entries : 3
===============================================================================
*A:ALA-BA#
standby
standby
Syntax
standby
Context
[Tree] (show>system>ptp standby)
Full Context
show system ptp standby
Description
This command displays information for PTP on the standby control module.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e, 7750 SR-2s, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, 7950 XRS
Output
The following output is an example of PTP standby information.
Output Example# show system ptp standby
===============================================================================
IEEE 1588/PTP Clock Information
===============================================================================
-------------------------------------------------------------------------------
Local Clock
-------------------------------------------------------------------------------
Clock Type : boundary PTP Profile : ITU-T G.8275.1
Domain : 24 Network Type : sdh
Admin State : up Oper State : up
Announce Interval : 8 pkt/s Announce Rx Timeout: 3 intervals
Peer Limit : none (Base Router)
G.8275 Priority : 128 PTSF-unusable : disabled
Clock Id : a47b2cfffe441e1f Clock Class : 165
Clock Accuracy : unknown Clock Variance : ffff (not computed)
Clock Priority1 : 128 Clock Priority2 : 128
-------------------------------------------------------------------------------
Parent Clock
-------------------------------------------------------------------------------
Port : 1/1/3 Remote MAC Address : a4:7b:2c:e2:f1:a2
Parent Clock Id : 242124fffe49e335 Remote PTP Port : 1
GM Clock Id : 242124fffe49e335 GM Clock Class : 6
GM Clock Accuracy : within 100 ns GM Clock Variance : 0x4e5d (1.8E-15)
GM Clock Priority1: 128 GM Clock Priority2 : 128
-------------------------------------------------------------------------------
Time Properties
-------------------------------------------------------------------------------
Timescale : PTP
Frequency Traceable : yes
Time Traceable : yes
Time Source : GPS
UTC Offset : +37 seconds
Leap Second : no leap second pending
-------------------------------------------------------------------------------
Frequency Recovery
-------------------------------------------------------------------------------
PTP Recovery State: initial Last Changed : 2021/09/02 11:04:48
Frequency Offset : -367.370 ppb
===============================================================================
standby-ip-addresses
standby-ip-addresses
Syntax
standby-ip-addresses
Context
[Tree] (show>subscr-mgmt>vrgw>brg>gateway standby-ip-addresses)
Full Context
show subscriber-mgmt vrgw brg gateway standby-ip-addresses
Description
This command shows associated home-aware pool standby IP addresses.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
start
start
Syntax
start
Context
[Tree] (tools>perform>router>l2tp>group>tunnel start)
Full Context
tools perform router l2tp group tunnel start
Description
This command triggers an attempt to start the control connection for a specified L2TP tunnel.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
start
Syntax
start route-downloader-name [force]
Context
[Tree] (tools>perform>aaa>route-downloader start)
Full Context
tools perform aaa route-downloader start
Description
This command causes the download process to start immediately. If an ongoing download is already in progress then no further action is needed, except if the force keyword is added. In case the force keyword is added, then the current download is aborted and a new one is immediately restarted. If aborting the current download, the internal route table should not be emptied or cleared.
Parameters
- route-downloader-name
-
Specifies the route downloader name, up to 32 characters.
- force
-
Causes the current download to be aborted and a new one is immediately restarted.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
static
static
Syntax
static [sap sap-id | sdp sdp-id:vc-id]
Context
[Tree] (show>service>id>mld-snooping static)
Full Context
show service id mld-snooping static
Description
This command displays MLD snooping static group membership data.
Platforms
All
Output
The following output is an example of MLD snooping static group membership information.
Output Example*A:rbae_C# show service id 1 mld-snooping static
===============================================================================
MLD Snooping Static Source Groups for service 1
-------------------------------------------------------------------------------
MLD Snooping Static Source Groups for SDP 36:1
-------------------------------------------------------------------------------
Source
Group
-------------------------------------------------------------------------------
2011:db8:1
FF04:db8:2
*
FF04:db8:3
-------------------------------------------------------------------------------
Static (*,G)/(S,G) entries: 2
===============================================================================
*A:rbae_C#
static
Syntax
static [sap sap-id | sdp sdp-id:vc-id]
Context
[Tree] (show>service>id>igmp-snooping static)
Full Context
show service id igmp-snooping static
Description
This command displays information on static IGMP snooping source groups for the VPLS service.
Parameters
- sap sap-id
-
Displays static IGMP snooping source groups for a specific SAP.
- sdp sdp-id
-
Displays the IGMP snooping source groups for a specific spoke or mesh SDP.
- vc-id
-
The virtual circuit ID on the SDP ID for which to display information.
Platforms
All
Output
Output Example*A:ALA-1>show>service>id>snooping# static
===============================================================================
IGMP Snooping Static Source Groups for SAP 1/1/2
-------------------------------------------------------------------------------
Source Group
-------------------------------------------------------------------------------
* 239.0.0.2
* 239.0.0.3
-------------------------------------------------------------------------------
Static (*,G)/(S,G) entries: 2
-------------------------------------------------------------------------------
IGMP Snooping Static Source Groups for SDP 10:10
-------------------------------------------------------------------------------
Source Group
-------------------------------------------------------------------------------
1.1.1.1 239.0.0.10
-------------------------------------------------------------------------------
Static (*,G)/(S,G) entries: 1
===============================================================================
*A:ALA-1>show>service>id>snooping#
Output fields: IGMP snooping source groups describes the show output fields.
|
Label |
Description |
|---|---|
|
Source |
Displays the IP source address used in IGMP queries. |
|
Group |
Displays the static IGMP snooping source groups for a specified SAP. |
static
Syntax
static [ip-int-name | ip-address]
Context
[Tree] (show>router>igmp static)
Full Context
show router igmp static
Description
This command displays static IGMP, (*,G) and (S,G) information.
Parameters
- ip-int-name
-
Displays information associated with the specified IP interface name, up to 32 characters.
- ip-address
-
Displays information associated with the specified IP address.
Platforms
All
Output
The following output is an example of IGMP static information. Output fields: IGMP static provides static IGMP field descriptions.
Output Example*A:ALA-BA# show router 100 igmp static
==================================================================
IGMP Static Group Source
==================================================================
Source Group Interface
------------------------------------------------------------------
10.11.11.11 239.136.22.3 IGMP_to_CE
* 239.1.1.1 IGMP_to_CE
10.22.22.22 239.255.255.255 IGMP_to_CE
------------------------------------------------------------------
Static (*,G)/(S,G) Entries : 3
==================================================================
*A:ALA-BA#
|
Label |
Description |
|---|---|
|
Source |
Entries that represent a source address from which receivers are interested/not interested in receiving multicast traffic. |
|
Group |
The IP multicast group address for which this entry contains information. |
|
Interface |
Displays the interface name. |
static
Syntax
static [ip-int-name | ip-address]
Context
[Tree] (show>router>mld static)
Full Context
show router mld static
Description
This command displays static MLD, (*,G) and (S,G) information.
Parameters
- ip-int-name
-
Displays the information associated with the specified IP interface name.
- ip-address
-
Displays the information associated with the specified IP address.
Platforms
All
Output
The following output is an example of MLD static information. Output fields: MLD static provides static MLD field descriptions.
Output Example*A:ALA-BA# show router mld static
===============================================================================
Rtr Base MLD Static Group Sources
===============================================================================
Source Interface
Group Start [Group Step]
[Group End] [Group Count]
-------------------------------------------------------------------------------
2001:db8:2016:10ff::4 lax-vls
ff05:db8:1
* lax-vls
ff06:db8:1
* lax-vls
ff01:db8:1 ::4:0
ff01:db8:100:0 64
3::1 lax-vls
ff05:db8:1 ::1
ff05:db8:20 32
* lax-vls
ff05:db8:2:1 ::1
ff05:db8:2:3ff 1023
3::1 lax-vls
ff05:db8:3:0 ::64
ff05:db8:4:0 656
3::2 lax-vls
ff05:db8:3:0 ::64
ff05:db8:4:0 656
4::1 flax-vlsoo
ff05:db8:3:0 ::64
ff05:db8:4:0 656
5::1 lax-vls
ff05:db8:3:0 ::64
ff05:db8:4:0 656
-------------------------------------------------------------------------------
Static (*,G)/(S,G) Entries : 9
===============================================================================
*A:ALA-BA#
|
Label |
Description |
|---|---|
|
Source |
The entries which represents a source address from which receivers are interested/not interested in receiving multicast traffic. |
|
Group |
The IP multicast group address for which this entry contains information. |
|
Interface |
The interface name. |
static
Syntax
static [head-end {local | ip-address}] [ color color] [end-point { ipv4-address | ipv6-address}] [preference preference-id] [distinguisher distinguisher-id]
static summary
Context
[Tree] (show>router>seg-rt>sr-policies static)
Full Context
show router segment-routing sr-policies static
Description
This command displays the traffic statistics of all or a filtered set of the static policies, or displays summary parameters.
Parameters
- head-end local
-
Filters on local head end.
- head-end ip-address
-
Filters on the head end IP address value.
- color
-
Filters on the color.
- ipv4-address | ipv6-address
-
Filters on the end-point IPv4 or IPv6 address.
- preference-id
-
Filters on the preference ID.
- distinguisher-id
-
Filters on the distinguisher ID.
- summary
-
Displays the summary information of the static policies.
Platforms
All
Output
The following output is an example of traffic statistics for the static policies.
Output Example Information for Static Policies *A:Dut-C# show router segment-routing sr-policies static
===============================================================================
SR-Policies Path
===============================================================================
-------------------------------------------------------------------------------
Type : srv6
Active : Yes Owner : static
Color : 10
Head : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
RD : 5 Preference : 14
SRv6 BSID 1 : 3333:3:3:3:0:b::
TunnelId : 917510 Age : 759
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 ReEvalReason : none
NumActPathChange: 0 Last Change : 06/13/2022 17:40:54
Maintenance Policy: N/A
Path Segment Lists:
Segment-List : 1 Weight : 1
S-BFD State : Down S-BFD Transitio*: 0
Num Segments : 1 Last Change : 06/10/2022 17:07:01
Seg 1 SID : 2222:2:2:2:0:a:: State : resolved-up
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router segment-routing sr-policies static end-point 3ffe::a14:102
===============================================================================
SR-Policies Path
===============================================================================
-------------------------------------------------------------------------------
Type : srv6
Active : Yes Owner : static
Color : 10
Head : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
RD : 5 Preference : 14
SRv6 BSID 1 : 3333:3:3:3:0:b::
TunnelId : 917510 Age : 426
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 ReEvalReason : none
NumActPathChange: 0 Last Change : 06/13/2022 17:40:54
Maintenance Policy: N/A
Path Segment Lists:
Segment-List : 1 Weight : 1
S-BFD State : Down S-BFD Transitio*: 0
Num Segments : 1 Last Change : 06/10/2022 17:07:01
Seg 1 SID : 2222:2:2:2:0:a:: State : resolved-up
===============================================================================
* indicates that the corresponding row element may have been truncated.
static-arp
static-arp
Syntax
static-arp [{ip-int-name | ip-address | mac ieee-mac-address}]
Context
[Tree] (show>router static-arp)
Full Context
show router static-arp
Description
This command displays the router static ARP table sorted by IP address. If no options are present, all ARP entries are displayed.
Parameters
- ip-int-name
-
Only displays static ARP entries associated with the specified IP interface name.
- ip-address
-
Only displays static ARP entries associated with the specified IP address.
- ieee-mac-address
-
Only displays static ARP entries associated with the specified MAC address.
Platforms
All
Output
Static ARP Table Output — The following output is an example of static AARP table information, and Output fields: static ARP describes the output fields.
Output ExampleA:ALA-A# show router static-arp
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
10.200.1.1 00:00:5a:01:00:33 00:00:00 Inv to-ser1a
-------------------------------------------------------------------------------
No. of ARP Entries: 1
===============================================================================
A:ALA-A#
A:ALA-A# show router static-arp 10.200.1.1
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.1.1 00:00:5a:01:00:33 00:00:00 Inv to-ser1
===============================================================================
A:ALA-A#
A:ALA-A# show router static-arp to-ser1
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
===============================================================================
A:ALA-A#
A:ALA-A# show router static-arp mac 00:00:5a:40:00:01
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
===============================================================================
A:ALA-A#
|
Label |
Description |
|---|---|
|
IP Address |
The IP address of the static ARP entry |
|
MAC Address |
The MAC address of the static ARP entry |
|
Age |
The age of the ARP entry. Static ARPs always have 00:00:00 for the age |
|
Type |
Inv — the ARP entry is an inactive static ARP entry (invalid) Sta — the ARP entry is an active static ARP entry |
|
Interface |
The IP interface name associated with the ARP entry |
|
No. of ARP Entries |
The number of ARP entries displayed in the list |
static-host
static-host
Syntax
static-host [sap sap-id] [wholesaler service-id] [port port-id][inter-dest-id intermediate-destination-id] [detail] [mac ieee-address] [ip-address ip-prefix[ /prefix-length]]
static-host [sap sap-id ][wholesaler service-id ][port port-id] no-inter-dest-id [ detail]
static-host summary
Context
[Tree] (show>service>id static-host)
Full Context
show service id static-host
Description
This command displays static hosts configured on this service.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- intermediate-destination-id
-
Specifies the intermediate destination identifier which is encoded in the identification strings up to 32 characters.
- summary
-
Displays summary static host information.
- detail
-
Displays detailed static host information.
- service-id
-
The service ID of the wholesaler.
- ieee-address
-
Specifies the MAC address.
- ip-prefix[/prefix-length]
-
Specifies the IP address.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of service static host information.
Output Example*A:ALA-48# show service id 88 static-host
===============================================================================
Static Hosts for service 88
===============================================================================
Sap IP Address Configured MAC Dynamic MAC
Subscriber Admin State Fwding State
-------------------------------------------------------------------------------
1/2/20:0 10.10.10.104 N/A N/A
N/A Down Not Fwding
3/2/4:50/5 10.144.145.1 N/A N/A
N/A Up Fwding
-------------------------------------------------------------------------------
Number of static hosts : 2
===============================================================================
*A:ALA-48#
static-lsp
static-lsp
Syntax
static-lsp [lsp-name]
static-lsp {transit | terminate}
static-lsp count
Context
[Tree] (show>router>mpls static-lsp)
Full Context
show router mpls static-lsp
Description
This command displays MPLS static LSP information.
Platforms
All
Output
The following output is an example of MPLS static LSP information.
Output fields: MPLS static LSP describes the MPLS static LSP output fields.
|
Label |
Description |
|---|---|
|
Lsp Name |
The name of the LSP used in the path up to 64 characters in length. |
|
To |
The system IP address of the egress router for the LSP. |
|
Next Hop |
The system IP address of the next hop in the LSP path. |
|
In I/F |
The ingress interface. |
|
Out Label |
The egress interface. |
|
Out I/F |
The egress interface. |
|
Adm |
Down — The path is administratively disabled. Up — The path is administratively enabled. |
|
Opr |
Down — The path is operationally down. Up — The path is operationally up. |
|
LSPs |
The total number of static LSPs. |
A:ALA-12# show router mpls static-lsp
===============================================================================
MPLS Static LSPs (Originating)
===============================================================================
Lsp Name To Next Hop Out Label Out I/F Adm Opr
-------------------------------------------------------------------------------
NYC_SJC_customer2 100.20.1.10 10.10.1.4 1020 1/1/1 Up Up
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
A:ALA-12#
*A:SRU4>config>router>mpls# show router mpls static-lsp transit
===============================================================================
MPLS Static LSPs (Transit)
===============================================================================
In Label In Port Out Label Out Port Next Hop Adm Opr
-------------------------------------------------------------------------------
240 aps-1 440 1/1/10 10.22.11.3 Up Up
241 aps-1 441 1/1/10 10.22.11.3 Up Up
242 aps-1 442 1/1/10 10.22.11.3 Up Up
243 aps-1 443 1/1/10 10.22.11.3 Up Up
244 aps-1 444 1/1/10 10.22.11.3 Up Up
245 aps-1 445 1/1/10 10.22.11.3 Up Up
246 aps-1 446 1/1/10 10.22.11.3 Up Up
247 aps-1 447 1/1/10 10.22.11.3 Up Up
248 aps-1 448 1/1/10 10.22.11.3 Up Up
249 aps-1 449 1/1/10 10.22.11.3 Up Up
250 aps-1 450 1/1/10 10.22.11.3 Up Up
251 aps-1 451 1/1/10 10.22.11.3 Up Up
252 aps-1 452 1/1/10 10.22.11.3 Up Up
253 aps-1 453 1/1/10 10.22.11.3 Up Up
...
207 3/2/8 407 1/1/9 10.22.10.3 Up Up
208 3/2/8 408 1/1/9 10.22.10.3 Up Up
209 3/2/8 409 1/1/9 10.22.10.3 Up Up
-------------------------------------------------------------------------------
LSPs : 256
===============================================================================
*A:SRU4>config>router>mpls#
A:ALA-12# show router mpls static-lsp terminate
===============================================================================
MPLS Static LSPs (Terminate)
===============================================================================
In Label In I/F Out Label Out I/F Next Hop Adm Opr
-------------------------------------------------------------------------------
1021 1/1/1 n/a n/a n/a Up Up
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
A:ALA-12#
static-policy
static-policy
Syntax
static-policy
static-policy name [detail]
Context
[Tree] (show>router>seg-rt>sr-policies static-policy)
Full Context
show router segment-routing sr-policies static-policy
Description
This command displays information about all static policies or the specified static policy.
Parameters
- name
-
Specifies the name of the static policy, up to 64 characters.
- detail
-
Displays detailed information about the static policy.
Platforms
All
Output
The following outputs are examples of information for a specified static policy.
Output Example Information for a Specific Static Policy*A:Dut-C# show router segment-routing sr-policies static-policy "a1"
===============================================================================
SR-Policies Static Policy
===============================================================================
Policy Name: a1
Type : srv6
Admin Status : Up Color : 10
Head End Addr : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
Preference : 14
RD : 5
SRv6 BSID 1 : N/A
Locator : C1
Function : End.B6.Encaps.Red Function Value : -
Function Stat*: error
Segment Lists Configuration:
Segment-List : 1 Weight : 1
Admin Status : Up Last Change : 06/13/2022 17:40:54
Segment Stack:
SRv6 SID 1: 2222:2:2:2:0:a::
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router segment-routing sr-policies static-policy "a1" detail
===============================================================================
SR-Policies Static Policy
===============================================================================
Policy Name: a1
Type : srv6
Admin Status : Up Color : 10
Head End Addr : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
Preference : 14
RD : 5
SRv6 BSID 1 : N/A
Locator : C1
Function : End.B6.Encaps.Red Function Value : -
Function Stat*: error
Path Entry:
Active : Yes Owner : static
TunnelId : 917510 Age : 346
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 ReEvalReason : none
NumActPathChange: 0 Last Change : 06/13/2022 17:40:54
Maintenance Policy: N/A
Path Segment Lists:
Segment-List : 1 Weight : 1
S-BFD State : Down S-BFD Transitio*: 0
Num Segments : 1 Last Change : 06/10/2022 17:07:01
Seg 1 SID : 2222:2:2:2:0:a:: State : resolved-up
===============================================================================
* indicates that the corresponding row element may have been truncated.
static-route
static-route
Syntax
static-route [family] [{ip-prefix/prefix-length | preference preference | [ next-hop ip-address | tag tag}] [ detail]
Context
[Tree] (show>router static-route)
Full Context
show router static-route
Description
This command displays the static entries in the routing table. If no options are present, all static routes are displayed sorted by prefix.
Parameters
- family
-
Specifies the type of routing information to be distributed by this peer group.
- ip-prefix/prefix-length
-
Displays static routes only matching the specified ip-prefix and mask.
- preference
-
Only displays static routes with the specified route preference.
- ip-address
-
Only displays static routes with the specified next hop IP address.
- tag
-
Displays the tag used to add a 32-bit integer tag to the static route. The tag is used in route policies to control distribution of the route into other protocols.
- detail
-
Displays detailed static routes information.
Platforms
All
Output
Static Route Output — The following output is an example of static route information, and Output fields: static route describes the fields.
Output ExampleA:ALA-A# show router static-route
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.250.0/24 5 1 ID 10.200.10.1 to-ser1 Y
192.168.252.0/24 5 1 NH 10.10.0.254 n/a N
192.168.253.0/24 5 1 NH to-ser1 n/a N
192.168.253.0/24 5 1 NH 10.10.0.254 n/a N
192.168.254.0/24 4 1 BH black-hole n/a Y
===============================================================================
A:ALA-A#
A:ALA-A# show router static-route 192.168.250.0/24
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.250.0/24 5 1 ID 10.200.10.1 to-ser1 Y
===============================================================================
A:ALA-A#
A:ALA-A# show router static-route preference 4
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.254.0/24 4 1 BH black-hole n/a Y
===============================================================================
A:ALA-A#
A:ALA-A# show router static-route next-hop 10.10.0.254
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.253.0/24 5 1 NH 10.10.0.254 n/a N
===============================================================================
A:ALA-A#
===============================================================================
Static Route Table (Router: Base) Family: IPv6
===============================================================================
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::10:20:1:6
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: any Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : disabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::20:20:1:6
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: any Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : disabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::20:20:1:5
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: any Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : disabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::10:20:1:5
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: filter Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : enabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
No. of Static Routes: 4
===============================================================================
*A:Dut-C#
A:Router#show router static-route 10.10.10.10/32 detail
===============================================================================
Static Route Table (Router: Base) Family: IPv4
===============================================================================
Prefix : 10.10.10.10/32
CommunityList : (Not Specified)
Tag : 0
Backup Tag : 0
Nexthop : 1.13.1.1 Validate Nexthop : No
Type : Nexthop
Backup Nexthop : 2.23.1.1 Backup Status : Active
Backup
Interface : Dut-C-Dut-A-1 Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Nexthop Tag : 0
Creation Origin : manual Load Bal Weight : n/a
BFD : disabled
Nexthop Community:
CPE-check : disabled
LDP Sync : disabled
-------------------------------------------------------------------------------
No. of Static Routes: 1
===============================================================================
A:Router#
|
Label |
Description |
|---|---|
|
IP Addr/mask |
The static route destination address and mask |
|
Pref |
The route preference value for the static route |
|
Metric |
The route metric value for the static route |
|
Type |
BH — the static route is a black hole route; the nexthop for this type of route is black-hole ID — the static route is an indirect route, where the nexthop for this type of route is the non-directly connected next hop NH — the route is a static route with a directly connected next-hop; the next-hop for this type of route is either the next-hop IP address or an egress IP interface name |
|
Nexthop |
The next hop for the static route destination |
|
Protocol |
The protocol through which the route was learned |
|
Interface |
The egress IP interface name for the static route n/a — indicates there is no current egress interface because the static route is inactive or a black hole route |
|
Active |
N — the static route is inactive; for example, the static route is disabled or the next hop IP interface is down Y — the static route is active |
|
No. of Routes |
The number of routes displayed in the list |
|
Backup Nexthop |
The backup next hop for the static route destination |
|
Backup Tag |
The tag value used for the static route when the primary next hop fails and the backup next hop is active |
|
Backup Status |
The status of the backup next hop |
static-route
Syntax
static-route ldp-sync-status
Context
[Tree] (tools>dump>router static-route)
Full Context
tools dump router static-route
Description
This command enables the synchronization status that static route keeps track of LDP interfaces.
Parameters
- ldp-sync-status
-
Specifies the LDP synchronization status.
Platforms
All
Output
The following output is an example of static route information.
Output Example*A:Dut-C# tools dump router static-route ldp-sync-status
===============================================================================
Sync Status of LDP interfaces
===============================================================================
If If Name Timer Running? Timeout Time
Index Yes/No Used Left
-------------------------------------------------------------------------------
2 ip-10.10.2.3 Yes 30 5
3 ip-10.10.3.3 No 30 0
4 ip-10.10.5.3 No 30 0
5 ip-10.10.22.3 No 30 0
6 ip-10.10.12.3 No 30 0
===============================================================================
static-sa
static-sa
Syntax
static-sa
static-sa name sa-name
static-sa spi spi
Context
[Tree] (show>ipsec static-sa)
Full Context
show ipsec static-sa
Description
This command displays IPsec static-SA information.
Parameters
- sa-name
-
Specifies the SA name.
- spi
-
Specifies the spi.
Platforms
All
station
station
Syntax
station [station-name]
Context
[Tree] (show>router>bmp station)
Full Context
show router bmp station
Description
This command displays BGP monitor (BMP) information.
Parameters
- station-name
-
Specifies the station name of a BMP monitoring station, up to 32 characters.
Platforms
All
Output
The following output is an example of BMP monitor information.
Output Example*A:Dut-C# show router bmp station
===============================================================================
BMP Stations (monitoring router "Base")
===============================================================================
Station Name Session State Since Msgs Sent
-------------------------------------------------------------------------------
lys ESTABLISHED 05/08/2018 15:32:12 103054
myr ESTABLISHED 05/08/2018 15:32:13 100007
-------------------------------------------------------------------------------
No. of BMP Stations: 2
===============================================================================
*A:Dut-C# show router bmp station "lys"
===============================================================================
BMP Station "lys" (monitoring router "Base")
===============================================================================
Admin State : enabled Global BMP State : enabled
Station Address : 100.3.7.7 Station Port : 12344
Via Router : Base TCP Auth Keychain:
Stats Report : 15 seconds Routes Report : 5 seconds
Connect Interval : 120 seconds Local Routes : reporting
Initiation Msg : Hello Station Lys
Reported families: ipv4
Session State : ESTABLISHED Last Change : 05/08/2018 15:32:12
Local Address : 100.3.7.3 Local Port : 51041
Stat Report Msgs : 3028 Route Report Msgs: 100021
Peer Up Msgs : 4 Peer Down Msgs : 0
Initiation Msgs : 1 Goodbye Msgs : 0
Bytes sent : 10926521
Stats Timer : 1 seconds left Routes Timer : 3 seconds left
Connect Timer : not running Monitored Peers : 3 of 4
Output queue : 0/50 Last Msg Sent : 05/15/2018 09:27:31
===============================================================================
*A:Dut-C#
station
Syntax
station station-name
station all
Context
[Tree] (clear>service>id>bmp station)
[Tree] (clear>router>bmp station)
Full Context
clear service id bmp station
clear router bmp station
Description
This command clears BMP station connections.
Parameters
- station-name
-
Specifies the BMP monitoring station name, up to 32 characters.
Platforms
All
station
Syntax
station [station-name]
Context
[Tree] (show>bmp station)
Full Context
show bmp station
Description
This command displays BMP station information.
Parameters
- station-name
-
Specifies the station name, up to 32 characters.
Platforms
All
statistics
statistics
Syntax
statistics [interface ip-int-name | ip-address]
Context
[Tree] (show>router>dhcp statistics)
Full Context
show router dhcp statistics
Description
This command displays statistics for DHCP Relay and DHCP snooping.
If no IP address or interface name is specified, all configured interfaces are displayed.
If an IP address or interface name is specified, only data regarding the specified interface is displayed.
Parameters
- ip-int-name | ip-address
-
Displays statistics for the specified IP interface.
Platforms
All
Output
The following command displays DHCP statistics information, and Output fields: DHCP statistics describes the output fields.
show router dhcp statistics====================================================================
DHCP Global Statistics (Router: Base)
====================================================================
Rx Packets : 0
Tx Packets : 0
Rx Malformed Packets : 0
Rx Untrusted Packets : 0
Client Packets Discarded : 0
Client Packets Relayed : 0
Client Packets Snooped : 0
Client Packets Proxied (RADIUS) : 0
Client Packets Proxied (Diameter) : 0
Client Packets Proxied (User-Db) : 0
Client Packets Proxied (Lease-Split) : 0
Server Packets Discarded : 0
Server Packets Relayed : 0
Server Packets Snooped : 0
DHCP RELEASEs Spoofed : 0
DHCP FORCERENEWs Spoofed : 0
Client packets streamed : 0
Routed Subnet Transparent Forwarded
Client Packets (BOOTREQUEST) : 0
Server Packets (BOOTREPLY) : 0
Other Opcode Packets : 0
====================================================================
|
Label |
Description |
|---|---|
|
Rx Packets |
The number of packets received from the DHCP clients |
|
Tx Packets |
The number of packets transmitted to the DHCP clients |
|
Rx Malformed Packets |
The number of malformed packets received from the DHCP clients |
|
Rx Untrusted Packets |
The number of untrusted packets received from the DHCP clients |
|
Client Packets Discarded |
The number of packets received from the DHCP clients that were discarded |
|
Client Packets Relayed |
The number of packets received from the DHCP clients that were forwarded |
|
Client Packets Snooped |
The number of packets received from the DHCP clients that were snooped |
|
Client Packets Proxied (RADIUS) |
The number of client packets proxied through RADIUS |
|
Client Packets Proxied (Diameter) |
The number of client packets proxied through Diameter |
|
Client Packets Proxied (User-Db) |
The number of client packets proxied through User-Db |
|
Client Packets Proxied (Lease-Split) |
The number of client packets proxied through a lease split |
|
Server Packets Discarded |
The number of packets received from the DHCP server that were discarded |
|
Server Packets Relayed |
The number of packets received from the DHCP server that were forwarded |
|
Server Packets Snooped |
The number of packets received from the DHCP server that were snooped |
|
DHCP RELEASEs Spoofed |
The number of spoofed DHCP releases |
|
DHCP FORCERENEWs Spoofed |
The number of spoofed FORCERENEW messages |
|
Client packets streamed |
The number of client packets streamed |
|
Routed Subnet Transparent Forwarded |
|
|
Client Packets (BOOTREQUEST) |
The number of DHCP client packets (BOOTREQUEST) received on a subscriber interface with the source IP in a routed subnet that is associated with a routed IPoE session or host. The routed-subnet-transparent-forwarding command must be configured in the routing instance. |
|
Server Packets (BOOTREPLY) |
The number of DHCP server packets (BOOTREPLY) received on a subscriber interface with the source IP in a routed subnet that is associated with a routed IPoE session or host. The routed-subnet-transparent-forwarding command must be configured in the routing instance. |
|
Other Opcode Packets |
The number of DHCP packets (Opcode field that are different from BOOTREQUEST and BOOTREPLY) received on a subscriber interface with the source IP in a routed subnet associated with a routed IPoE session or host. The routed-subnet-transparent-forwarding command must be configured in the routing instance. Note: When transparent forwarding is
enabled, the system does not check if the DHCP packet is
valid and therefore packets with an Opcode field
different from BOOTREQUEST and BOOTREPLY are
forwarded.
|
statistics
Syntax
statistics [interface ip-int-name]
Context
[Tree] (show>router>dhcp6 statistics)
[Tree] (show>service>id>dhcp6 statistics)
Full Context
show router dhcp6 statistics
show service id dhcp6 statistics
Description
This command displays statistics for DHCPv6 relay and snooping.
Parameters
- ip-int-name
-
Specifies to display interface name information.
Platforms
All
Output
The following output is an example of DHCP6 statistics information.
Output ExampleA:Dut-A# show service id 20 dhcp6 statistics
====================================================================
DHCP Statistics, service 20, all interfaces
====================================================================
Packets received : 0
Packets transmitted : 0
Packets dropped : 0
====================================================================
====================================================================
DHCP Statistics, service 21, all SAPs
====================================================================
Client packets snooped : 2
Client packets forwarded : 2
Client packets dropped : 19
Server packets snooped : 2
Server packets forwarded : 2
Server packets dropped : 0
====================================================================A:Dut-A# show service id 1000 dhcp6 statistics
====================================================================
DHCP Statistics, service 1000, all interfaces
====================================================================
Packets received : 16063
Packets transmitted : 16061
Packets dropped : 0
====================================================================
====================================================================
DHCP Statistics, service 1000, all SAPs
====================================================================
Client packets snooped : 0
Client packets forwarded : 0
Client packets dropped : 0
Server packets snooped : 0
Server packets forwarded : 0
Server packets dropped : 0
==================================================================== Output fields: DHCP6 statistics describes DHCP6 output statistics.
|
Field |
Description |
|---|---|
|
Client Packets Dropped |
The number of DHCPv6 client packets snooped on SAP ingress and dropped, for example: DHCPv6 client packet received on an LDRA enabled network-facing SAP |
|
Client Packets Forwarded |
The number of DHCPv6 client packets snooped on SAP ingress and forwarded |
|
Client Packets Snooped |
The number of DHCPv6 client packets snooped on SAP ingress |
|
Server Packets Dropped |
The number of DHCPv6 server packets snooped on SAP ingress and dropped, for example: DHCPv6 server packet received on an LDRA enabled client-facing SAP |
|
Server Packets Forwarded |
The number of DHCPv6 server packets snooped on SAP ingress and forwarded |
|
Server Packets Snooped |
The number of DHCPv6 server packets snooped on SAP ingress |
statistics
Syntax
statistics [[sap sap-id] | [sdp sdp-id:vc-id] | [interface interface-name]]
Context
[Tree] (show>service>id>dhcp statistics)
Full Context
show service id dhcp statistics
Description
This command displays DHCP relay statistics.
Parameters
- ip-int-name
-
Displays DHCP statistics on the specified interface.
- interface-name
-
Displays DHCP statistics for the specified interface name.
- sap-id
-
Displays DHCP statistics for the specified SAP.
Platforms
All
Output
The following output is an example of DHCP statistics information.
Output Example*A:ALA-48# show service id 88 dhcp statistics interface SpokeTerm
===================================================================
DHCP Statistics for interface SpokeTerm
===================================================================
Rx Packets : 0
Tx Packets : 0
Rx Malformed Packets : 0
Rx Untrusted Packets : 0
Client Packets Discarded : 0
Client Packets Relayed : 0
Client Packets Snooped : 0
Client Packets Proxied (RADIUS) : 0
Client Packets Proxied (Lease-Split) : 0
Server Packets Discarded : 0
Server Packets Relayed : 0
Server Packets Snooped : 0
DHCP RELEASEs Spoofed : 0
DHCP FORCERENEWs Spoofed : 0
===================================================================
*A:ALA-48#
Output fields: DHCP statistics interface describes DHCP statistics output fields.
|
Field |
Description |
|---|---|
|
Rx Packets |
The number of received packets |
|
Tx Packets |
The number of transmitted packets |
|
Rx Malformed |
The number of malformed packets received |
|
Rx Untrusted Packets |
The number of untrusted packets received |
|
Client Packets Discarded |
The number of client packets discarded |
|
Client Packets Relayed |
The number of client packets relayed |
|
Client Packets Snooped |
The number of client packets snooped |
|
Client Packets Proxied (RADIUS) |
The number of client packets proxied through RADIUS |
|
Client Packets Proxied (Lease-Split) |
The number of client packets proxied through a lease split |
|
Server Packets Discarded |
The number of discarded server packets |
|
Server Packets Relayed |
The number of relayed server packets |
|
Server Packets Snooped |
The number of snooped server packets |
|
DHCP RELEASEs Spoofed |
The number of spoofed DHCP releases |
|
DHCP FORCERENEWs Spoofed |
The number of spoofed FORCERENEW messages |
statistics
Syntax
statistics
statistics interface {ip-int-name | ip-address}
statistics sap sap-id
Context
[Tree] (show>service>id>ppp statistics)
Full Context
show service id ppp statistics
Description
This command displays PPP statistics.
Parameters
- ip-int-name
-
Displays information about the specified interface, up to 32 characters.
- ip-address
-
Displays information about the specified IP address.
- sap-id
-
Displays information for the specified SAP.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
statistics frag-stats
statistics map-domain domain-name mapping-rule rule-name
Context
[Tree] (clear>nat>map statistics)
Full Context
clear nat map statistics
Description
This command clears MAP statistics.
Parameters
- domain-name
-
Clears MAP statistics for the specified domain name, up to 32 characters.
- rule-name
-
Clears MAP statistics for the specified mapping rule name, up to 32 characters.
Platforms
7750 SR-1-24D, 7750 SR-1-46S, 7750 SR-1-48D, 7750 SR-1-92S, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-1se, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, VSR
statistics
Syntax
statistics [{ip-address | ip-int-name}]
Context
[Tree] (clear>router>dhcp statistics)
Full Context
clear router dhcp statistics
Description
This command clears statistics for DHCP statistics.
If no IP address or interface name is specified, then statistics are cleared for all configured interfaces.
If an IP address or interface name is specified, then only data regarding the specified interface is cleared.
Parameters
- ip-int-name
-
Clears DHCP statistics for the specified interface name.
- ip-address
-
Clears DHCP statistics for the specified IP address.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>router>dhcp6 statistics)
Full Context
clear router dhcp6 statistics
Description
This command clears DHCP6 statistics.
Platforms
All
statistics
Syntax
statistics
statistics interface ip-int-name | ipv6-address
statistics sap sap-id
Context
[Tree] (clear>service>id>dhcp6 statistics)
Full Context
clear service id dhcp6 statistics
Description
This command clears DHCPv6 statistics for interfaces and VPLS SAPs.
Parameters
- ip-int-name
-
Clears DHCPv6 statistics for the specified interface name.
- ipv6-address
-
Clears DHCPv6 statistics for the specified IP address.
- sap-id
-
Clears DHCPv6 statistics for the specified VPLS SAP.
Platforms
All
statistics
Syntax
statistics [{sap sap-id | sdp sdp-id:vc-id | interface { ip-address | ip-int-name}}]
Context
[Tree] (clear>service>id>dhcp statistics)
Full Context
clear service id dhcp statistics
Description
This command clears DHCP statistics.
Parameters
- sap-id
-
Clears the specified SAP information.
- sdp-id
-
The specified SDP to be cleared.
- vc-id
-
Specifies the virtual circuit ID on the SDP ID to be cleared.
- ip-address
-
Specifies the interface IP address.
- ip-int-name
-
Specifies the interface name, up to 32 characters.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>subscr-mgmt>gtp statistics)
Full Context
show subscriber-mgmt gtp statistics
Description
This command displays GTP statistics information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of GTP statistics.
Output ExampleNode# show subscriber-mgmt gtp statistics
===============================================================================
GTP statistics
===============================================================================
tx echo requests : 23
tx echo responses : 0
tx errors : 0
rx echo requests : 0
rx echo responses : 23
rx errors : 0
rx version not supported : 0
rx zero TEID responses : 0
path faults : 0
path restarts : 0
tx invalid msgs : 0
tx create PDP context requests : 0
tx create PDP context responses : 0
tx delete PDP context requests : 0
tx delete PDP context responses : 0
tx create session requests : 0
tx create session responses : 1
tx delete session requests : 0
tx delete session responses : 0
tx delete bearer requests : 0
tx delete bearer responses : 0
tx create bearer responses : 0
tx update bearer responses : 0
tx modify bearer requests : 0
tx modify bearer responses : 1
tx change notification responses : 0
tx rls access bearers responses : 0
tx error indication count : 0
tx downlink notifications : 0
tx stop paging indication : 0
tx end marker : 0
rx invalid msgs : 0
rx create PDP context requests : 0
rx create PDP context responses : 0
rx delete PDP context requests : 0
rx delete PDP context responses : 0
rx create session requests : 1
rx create session responses : 0
rx delete session requests : 0
rx delete session responses : 0
rx delete bearer requests : 0
rx delete bearer responses : 0
rx create bearer requests : 0
rx update bearer requests : 0
rx modify bearer requests : 1
rx modify bearer responses : 0
rx change notification requests : 0
rx rls access bearers request : 0
rx error indication count : 0
rx downlink notification ack : 0
rx downlink notification fail : 0
rx invalid pkt length : 0
rx unknown pkts : 0
rx missing IE pkts : 0
rx bad UDP header pkts : 0
rx discarded pkts : 0
rx in-session discarded pkts : 0
rx pkts : 25
tx discarded pkts : 0
tx pkts : 25
rx UDP checksum error : 0
===============================================================================
statistics
Syntax
statistics
Context
[Tree] (show>router>l2tp statistics)
Full Context
show router l2tp statistics
Description
This command displays L2TP statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of L2TP statistics information.
Output Example*A:Dut-C# show router l2tp statistics
===============================================================================
L2TP Statistics
===============================================================================
Tunnels Sessions
-------------------------------------------------------------------------------
Active : 3 Active : 6
Setup history since 04/17/2009 18:38:41
Total : 4 Total : 9
Failed : 0 Failed : 0
Failed Auth : 0
===============================================================================
*A:Dut-C#
statistics
Syntax
statistics [{sap sap-id | interface ip-int-name | ip-address}]
Context
[Tree] (show>service>id>pppoe statistics)
Full Context
show service id pppoe statistics
Description
This command displays PPPoE statistics.
Parameters
- sap-id
-
Displays information for the specified SAP.
- ip-int-name
-
Displays information about the specified interface.
- ip-address
-
Displays information about the specified IP address.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PPPoE statistics information.
Output Example*A:ALA-49# show service id 20 pppoe statistics
===============================================================================
PPPoE statistics for IES service 20
===============================================================================
Packet Type Received Transmitted
-------------------------------------------------------------------------------
PADI 2 -
PADO - 2
PADR 2 -
PADS - 2
PADT 0 0
session 9838 9839
-------------------------------------------------------------------------------
Drop Counters
-------------------------------------------------------------------------------
Rx Invalid Version : 0
Rx Invalid Type : 0
Rx Invalid Code : 0
Rx Invalid Session : 0
Rx Invalid Length : 0
Rx Invalid Tags : 0
Rx Invalid AC-Cookie : 0
Rx Dropped : 0
===============================================================================
*A:ALA-49#
statistics
Syntax
statistics
Context
[Tree] (clear>router>l2tp>tunnel statistics)
[Tree] (clear>router>l2tp>peer statistics)
[Tree] (clear>router>l2tp>group statistics)
[Tree] (clear>router>l2tp statistics)
Full Context
clear router l2tp tunnel statistics
clear router l2tp peer statistics
clear router l2tp group statistics
clear router l2tp statistics
Description
This command clears statistics for the specified context.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics [{sap sap-id | interface ip-int-name | ip-address}]
Context
[Tree] (clear>service>id>pppoe statistics)
Full Context
clear service id pppoe statistics
Description
This command clears PPPoE statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (show>service>dynsvc>script statistics)
Full Context
show service dynamic-services script statistics
Description
This command displays dynamic service script statistics. Only non-zero values are shown.
The script statistics can be cleared with the "clear service statistics dynamic-services” command.
This command is not available in the MD-CLI.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of Dynamic Services script statistics information, and Output fields: dynamic services script statistics describes the output fields.
Output Example# show service dynamic-services script statistics
===============================================================================
Dynamic Services Script Statistics
===============================================================================
Description Counter
-------------------------------------------------------------------------------
python scripts with 0 retries due to timeout 46
setup - jobs launched 16
setup - jobs handled 16
setup - success 13
setup - syntax error 1
setup - execution failed 2
teardown - jobs launched 15
teardown - jobs handled 15
teardown - success 14
teardown - syntax error 1
-------------------------------------------------------------------------------
No. of Script Statistics: 10
-------------------------------------------------------------------------------
Last Cleared Time: 02/26/2013 09:59:07
===============================================================================
|
Output field |
Description |
|---|---|
|
Description |
The name of the script. |
|
Counter |
The number of times the script executed. |
|
python scripts with 0 retries due to timeout |
The number of retries due to timeouts. |
|
setup |
The setup script action. jobs launched — The number of times the setup jobs launched. jobs handled — The number of times the setup jobs were handled. success — The number of times the setup jobs were successful. syntax error — The number of setup syntax errors. execution failed — The number of times the setup failed. |
|
teardown |
The teardown script action. jobs launched — The number of times the teardown jobs launched. jobs handled — The number of times the teardown jobs were handled. success — The number of times the teardown jobs were successful. syntax error — The number of teardown syntax errors. |
statistics
Syntax
statistics iom (slot | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics mda (mda | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics port (port-id | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics pw-port (pw-port | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics system (pw-port | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics service (svc-id | all) [host | session | summary] [non-zero-value-only]
statistics service {svc-id} subscriber-interface { sub-itf | all} [host | session | summary] [non-zero-value-only]
statistics service {svc-id} group-interface { grp-itf | all} [host | session | summary] [non-zero-value-only]
statistics sla-profiles
statistics sub-profiles
statistics system [host | session | subscriber | summary] [non-zero-value-only]
Context
[Tree] (show>subscr-mgmt statistics)
Full Context
show subscriber-mgmt statistics
Description
This command displays enhanced subscriber management statistics per port, PW port, MDA, IOM, system, service, subscriber interface, or group interface.
For each statistic, a current value and peak value is displayed. The peak value is the highest generated value since the last reset as a result of a system boot or the clear subscriber-mgmt peakvalue-stats command.
The user can execute the clear subscriber-mgmt peakvalue-stats command to reset the peak values.
Parameters
- iom slot
-
Displays specified IOM slot information.
- mda mda
-
Displays specified slot and mda information.
- port port-id
-
Specifies to display information for both the physical port ID and LAG.
- pw-port pw-port
-
Specifies to display information for a pseudowire port ID.
- all
-
Displays statistics of all IOM or MDA or port or pseudowire port in the system
- host
-
Displays v4/v6 host statistics only.
- session
-
Displays PPPoX/LAC/LNS session statistics only.
- sla-profiles
-
Displays the current and historical statistics for SLA profiles.
- service svc-id
-
Displays the current and historical statistics for service level profiles.
- sub-profiles
-
Displays the current and historical statistics for subscriber profiles.
- subscriber
-
Displays subscriber statistics only.
- subscriber-interface sub-itf
-
Displays specified subscriber interface level statistics, up to 32 characters.
- group-interface grp-itf
-
Displays specified group-interface level statistics, up to 32 characters.
- summary
-
Displays summary statistics only.
- non-zero-value-only
-
Displays only non-zero value counters.
The following tables describe the counters available in the show subscriber management statistics command output.
The following terminology is used to indicate applicability of the stats:
-
ESM — Enhanced Subscriber Management. Subscriber traffic forwarded via subscriber queues. Enabled with SAP sub-sla-mgmt in no shutdown state
-
BSM — Basic Subscriber Management. Subscriber traffic forwarded via SAP queues. SAP sub-sla-mgmt must be in shutdown state. For DHCP, dhcp lease-populate or dhcp6-relay lease-populate must be enabled to count the leases. For IPv4, if anti-spoof is enabled on the SAP, a subscriber host is instantiated.
-
Routed CO — IES or VPRN service with subscriber interface and group interface constructs
-
Bridged CO — VPLS service with DHCPv4 lease management enabled (lease-populate)
-
regular interface — IES or VPRN interface (none subscriber-interface or group-interface)
-
Host (also subscriber host) — A resource in the system that is used for traffic forwarding and security related actions. The creation of a subscriber host entry is linked to anti-spoof being enabled on a SAP. For ESM, anti-spoof is mandatory and hence every connected {IP/MAC} consumes by default a subscriber host entry. A DHCP6 IA-PD can also be modeled as a managed route. In this case, no subscriber host is instantiated. For BSM, anti-spoof is optional on regular interfaces. An IPv4 static-host and DHCPv4 lease do not result in a subscriber host instantiation when anti-spoof is disabled on the SAP.
Table 50. Output fields: host and protocol statistics Section
Counter
Counts
Applies to
IPv4
PPP Hosts - IPCP
IPv4 local terminated PPP hosts (PTA, LNS)
ESM, Routed CO
IPOE Hosts - DHCP
DHCPv4 hosts (lease states)
ESM, Routed CO, Bridged CO
IPOE Hosts - ARP
ARP hosts
ESM, Routed CO, Bridged CO
IPOE Hosts – Static
IPv4 static hosts
ESM, Routed CO, Bridged CO
IPOE Mngd Hosts – Data-trig
Data triggered IPv4 hosts
ESM, Routed CO
IPOE Mngd Hosts – AAA
vRGW managed static IPv4 addresses: IPv4 static hosts created via RADIUS (Alc-Reserved-Addresses)
ESM, Routed CO
IPOE Mngd Hosts – GTP
IPv4 GTP access host
ESM, Routed CO
IPOE Mngd Hosts – Bonding
IPv4 hosts associated with an internal IPoE session of a connection bonding subscriber context
ESM, Routed CO
IPOE Hosts BSM - DHCP
DHCPv4 hosts (lease states: anti-spoof and lease-populate enabled)
BSM, Routed CO, Bridged CO, regular interface
IPOE Hosts BSM – Static
IPv4 static hosts (with anti-spoof enabled)
BSM, Routed CO, Bridged CO, regular interface
IPOE BSM - DHCP
DHCPv4 lease states (with lease-populate enabled, no anti-spoof)
BSM, Routed CO, Bridged CO, regular interface
IPOE BSM – Static
IPv4 static hosts (no anti-spoof)
BSM, Routed CO, Bridged CO, regular interface
IPv6
PPP Hosts – SLAAC
Local terminated IPv6 wan-host – SLAAC (PTA, LNS)
ESM, Routed CO
PPP Hosts - DHCP6 (NA)
Local terminated IPv6 wan-host (PTA, LNS) – DHCP6 IA-NA leases over PPP
ESM, Routed CO
PPP Hosts - DHCP6 (PD)
Local terminated IPv6 pd-host (PTA, LNS) – DHCP6 IA-PD leases over PPP (excluding PD as managed route)
ESM, Routed CO
PPP Mngd Routes - DHCP6 (PD)
IPv6 (PTA, LNS) – DHCP6 IA-PD leases over PPP (PD as managed route only)
ESM, Routed CO
IPOE Hosts – SLAAC
IPv6 wan-host – SLAAC
ESM, Routed CO
IPOE Hosts - DHCP6 (NA)
IPv6 wan-host – DHCP6 IA-NA leases
ESM, Routed CO
IPOE Hosts - DHCP6 (PD)
IPv6 pd-host – DHCP6 IA-PD leases (excluding PD as managed route)
ESM, Routed CO
IPOE Mngd Routes - DHCP6 (PD)
IPv6 – DHCP6 IA-PD leases (PD as managed route only)
ESM, Routed CO
IPOE Hosts – Static (WAN)
IPv6 static hosts with prefix-length equal to /128
ESM, Routed CO
IPOE Hosts – Static (Pfx)
IPv6 static hosts with prefix-length shorter than /128
ESM, Routed CO
IPOE Mngd Hosts – Data-trig (Pfx)
Data triggered IPv6 Prefix host (prefix length shorter than /128)
ESM, Routed CO
IPOE Mngd Hosts – Data-trig (Pfx)
Data triggered IPv6 Prefix host (prefix length shorter than /128)
ESM, Routed CO
IPv6 (Cont)
IPOE Mngd Routes – Data-trig (Pfx)
Data triggered IPv6 Prefix (prefix length shorter than /128) modeled as a managed route
ESM, Routed CO
IPOE Mngd Hosts - AAA
(currently unused)
Not applicable
IPOE Mngd Hosts – GTP (SLAAC)
IPv6 (SLAAC) GTP Access host
ESM, Routed CO
IPOE Mngd Hosts - Bonding
IPv6 hosts associated with an internal IPoE session of a connection bonding subscriber context..
ESM, Routed CO
IPOE BSM - DHCP6 (NA)
IPv6 – DHCP6 IA-NA leases (lease-populate)
BSM, regular interface
IPOE BSM - DHCP6 (PD)
IPv6 – DHCP6 IA-PD leases (lease-populate)
BSM, regular interface
Total
PPP Hosts
Local terminated PPP hosts (PTA, LNS)
ESM
IPOE Hosts
Total IPv4 and IPv6 IPOE hosts
ESM
IPv4 Hosts
Total IPv4 hosts, PPP (PTA, LNS) and IPOE
ESM
IPv6 Hosts
Total IPv6 hosts, PPP (PTA, LNS) and IPOE
ESM
IPv6 PD Mngd Routes
Total DHCP6 IA-PD leases modeled as a managed route. PPP (PTA, LNS) and IPOE
ESM
L2TP LAC Hosts
L2TP LAC hosts – single host per single or dual stack PPP session
Counter also increases for outgoing LTS sessions.
ESM, Routed CO
L2TP LNS Hosts
L2TP LNS hosts – single host per single or dual stack PPP session
ESM, Routed CO
Internal Hosts
Subscriber hosts for internal use. For example, LNS redirect hosts (for LTS, an LNS redirect host is also instantiated).
The internal LNS redirect host only counts against the system limit and not against the per line card limit.
ESM
Total (Cont)
Non-Sub-Traffic L2-Hosts
A host on a single subscriber SAP in a VPLS service that enables non-IP traffic to be forwarded using the specified SLA profile instance queues.
Host on a single subscriber SAP attached to an IES or VPRN group-interface that enables traffic normally forwarded using the SAP queues to flow using the specified SLA profile instance queues.
configure>service>vpls service-id>sap sap-id>sub-sla-mgmt single-sub-parameters>non-sub-traffic sub-profile sub-profile-name sla-profile sla-profile-name [subscriber sub-ident-string] [app-profile app-profile-name]
ESM, Routed CO, Bridged CO
DHCP leases
Total number of DHCPv4 lease states
ESM, BSM
DHCPv6 leases
Total number of DHCPv6 lease states
ESM, BSM
Subscriber Hosts
Counter displayed in the output of show>subscriber-mgmt>statistics [ iom | mda | port | pw-port]
ESM
System Hosts Scale
Counter displayed in the output of show>subscriber-mgmt>statistics system
This counter matches the number of hosts accounted for in the system wide limit.
ESM
Table 51. Output fields: PPP session statistics Section
Counter
Counts
Applies to
Local
PPP Sessions - PPPoE
Local terminated PPPoE sessions (PTA)
ESM, Routed CO
PPP Sessions - PPPoEoA
Local terminated PPPoEoA sessions (PTA)
ESM, Routed CO
PPP Sessions - PPPoA
Local terminated PPPoA sessions (PTA)
ESM, Routed CO
PPP Sessions - L2TP (LNS)
Local terminated PPP sessions (L2TP LNS)
ESM, Routed CO
LAC
PPP Sessions - PPPoE
Tunneled PPPoE session (L2TP LAC)
ESM, Routed CO
PPP Sessions - PPPoEoA
Tunneled PPPoEoA session (L2TP LAC)
ESM, Routed CO
PPP Sessions - PPPoA
Tunneled PPPoA session (L2TP LAC)
ESM, Routed CO
PPP Sessions - L2TP (LTS)
Tunneled PPP session (L2TP LTS)
ESM, Routed CO
Total
PPP Sessions - established
PPP sessions that are established (at least one active host attached) – PTA/LAC/LTS/LNS
ESM, Routed CO
PPP Sessions - in setup
PPP sessions in setup (session created, host setup in progress) – PTA/LAC/LTS/LNS
ESM, Routed CO
PPP Sessions - local
Local terminated PPPoX sessions (PTA, L2TP LNS)
ESM, Routed CO
PPP Sessions - LAC
Tunneled PPPoX session (L2TP LAC, L2TP LTS)
ESM, Routed CO
L2TP
L2TP Tunnels - originator
Number of L2TP Tunnels originated on this node. (LAC/LTS)
ESM, Routed CO
.L2TP Tunnels - receiver
Number of L2TP Tunnels terminated on this node. (LNS/LTS)
ESM, Routed CO
Total L2TP Tunnels
Number of L2TP Tunnels originated or terminated on this node.
ESM, Routed CO
Table 52. Output fields: IPoE session statistics Section
Counter
Counts
Applies to
Total
IPOE Sessions - established
IPoE sessions that are established (at least one active host attached).
ESM, Routed CO
IPOE Sessions- in setup
IPoE sessions in setup (session created, host setup in progress).
ESM, Routed CO
Table 53. Output fields: subscriber statistics Section
Counter
Counts
Applies to
Total
Subscribers
Total number of active subscribers.
ESM, Routed CO, Bridged CO
Table 54. Output fields: subscriber management statistics summary Section
Counter
Counts
Hosts
IPv4
IPv6
Total IPv4 hosts
Total IPv6 hosts
Sessions
PPP
IPOE
Total PPP sessions established
Total IPOE sessions established
Subscribers
Total number of active subscribers
-
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following outputs are examples of subscriber management statistics information.
Output ExampleA:PE-1# show subscriber-mgmt statistics port 1/1/4 summary
===============================================================================
SubMgmt Statistics
===============================================================================
| Hosts | Sessions | Subscribers
Port Id | IPv4 IPv6 | PPP IPOE |
-------------------------------------------------------------------------------
1/1/4 | 2 2 | 1 1 | 2 (Curr)
| 3 3 | 1 2 | 3 (Peak)
===============================================================================
A:PE-1# show subscriber-mgmt statistics sla-profiles
===============================================================================
SLA Profile Statistics
===============================================================================
SLA-Profile Name Current Peak Peak Timestamp
-------------------------------------------------------------------------------
tv-prof 0 0
hsi-prof 1 1 12/29/2016 15:50:50
hsi-iptv--prof 0 0
no-prof-1 1 1 01/03/2017 20:00:37
hsi-voip-prof 0 2 12/29/2016 18:42:44
-------------------------------------------------------------------------------
Total 2
===============================================================================
A:PE-1# show subscriber-mgmt statistics sub-profiles
===============================================================================
Subscriber Profile Statistics
===============================================================================
Subscriber-Profile Name Current Peak Peak Timestamp
-------------------------------------------------------------------------------
no-prof 2 3 12/29/2016 18:42:44
sub-10M 0 0
sub-10M-UPNP 0 0
sub-20M 0 0
sub-20M-UPNP 0 0
-------------------------------------------------------------------------------
Total 2
===============================================================================
A:pe1# show subscriber-mgmt statistics system
===============================================================================
Subscriber Management Statistics for System
===============================================================================
Type Current Peak Peak Timestamp
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Host & Protocol Statistics
-------------------------------------------------------------------------------
IPv4 PPP Hosts - IPCP 0 0
PPP Hosts - PFCP 0 0
IPOE Hosts - DHCP 0 0
IPOE Hosts - ARP 0 0
IPOE Hosts - Static 0 0
IPOE Hosts - PFCP 0 0
IPOE Mngd Hosts - Data-trig 0 0
IPOE Mngd Hosts - AAA 0 0
IPOE Mngd Hosts - GTP 0 0
IPOE Mngd Hosts - Bonding 0 0
IPOE Hosts BSM - DHCP 0 0
IPOE Hosts BSM - Static 0 0
IPOE BSM - DHCP 0 0
IPOE BSM - Static 0 0
-------------------------------------------------------------------------------
IPv6 PPP Hosts - SLAAC 0 0
PPP Hosts - DHCP6 (NA) 0 0
PPP Hosts - DHCP6 (PD) 0 0
PPP Mngd Routes - DHCP6 (PD) 0 0
PPP Hosts - PFCP (SLAAC) 0 0
PPP Hosts - PFCP (NA) 0 0
PPP Hosts - PFCP (PD) 0 0
IPOE Hosts - SLAAC 0 0
IPOE Hosts - DHCP6 (NA) 0 0
IPOE Hosts - DHCP6 (PD) 0 0
IPOE Mngd Routes - DHCP6 (PD) 0 0
IPOE Hosts - Static (WAN) 0 0
IPOE Hosts - Static (Pfx) 0 0
IPOE Hosts - PFCP (SLAAC) 0 0
IPOE Hosts - PFCP (NA) 0 0
IPOE Hosts - PFCP (PD) 0 0
IPOE Mngd Hosts - Data-trig (WAN) 0 0
IPOE Mngd Hosts - Data-trig (Pfx) 0 0
IPOE Mngd Routes - Data-trig (Pfx) 0 0
IPOE Mngd Hosts - AAA 0 0
IPOE Mngd Hosts - GTP (SLAAC) 0 0
IPOE Mngd Hosts - Bonding 0 0
IPOE BSM - DHCP6 (NA) 0 0
IPOE BSM - DHCP6 (PD) 0 0
-------------------------------------------------------------------------------
Total PPP Hosts 0 0
IPOE Hosts 0 0
IPv4 Hosts 0 0
IPv6 Hosts 0 0
IPv6 PD Mngd Routes 0 0
L2TP LAC Hosts 0 0
L2TP LNS Hosts 0 0
Internal Hosts 0 0
Non-Sub-Traffic L2-Hosts 0 0
DHCP Leases 0 0
DHCPv6 Leases 0 0
PFCP Hosts 0 0
System Hosts Scale 0 0
-------------------------------------------------------------------------------
statistics
Syntax
statistics sub-profile {sub-profile-name | all}
statistics sla-profile {sla-profile-name | all}
Context
[Tree] (clear>subscriber-mgmt statistics)
Full Context
clear subscriber-mgmt statistics
Description
This command clears the current and historical statistics.
Parameters
- sub-profile-name
-
Clears the statistics for a specific subscriber profile, limited to 32 characters.
- sub-profile all
-
Clears all subscriber profile statistics.
- sla-profile-name
-
Clears the statistics for a specific SLA profile, limited to 32 characters.
- sla-profile all
-
Clears all SLA profile statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics interface subscriber-interface [ id srrp-id]
Context
[Tree] (clear>router>srrp statistics)
Full Context
clear router srrp statistics
Description
This command clears statistics for SRRP instances.
Parameters
- subscriber-interface
-
Specifies an existing subscriber interface name up to 32 characters.
- srrp-id
-
Specifies an existing SRRP ID.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>service statistics)
Full Context
clear service statistics
Description
This command clears the statistics for a service.
Platforms
All
statistics
Syntax
statistics [policy name] [sap sap-id]
Context
[Tree] (show>service>id>auth statistics)
Full Context
show service id authentication statistics
Description
This command displays session authentication statistics for this service.
Parameters
- policy name
-
Specifies an existing authentication policy name.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
Platforms
All
Output
The following output is an example of service authentication statistics information
Output Example*A:ALA-48# show service id 700 authentication statistics
================================================================
Authentication Statistics for service 700
================================================================
Client Packets Authenticate Fail : 0
Client Packets Authenticate Ok : 0
================================================================
*A:ALA-48#
statistics
Syntax
statistics [sap sap-id | sdp sdp-id:vc-id]
Context
[Tree] (show>service>id>mld-snooping statistics)
Full Context
show service id mld-snooping statistics
Description
This command displays MLD snooping statistics.
Platforms
All
Output
The following output is an example of MLD snooping statistics information.
Output Example*A:rbae_C# show service id 1 mld-snooping statistics
===============================================================================
MLD Snooping Statistics for service 1
===============================================================================
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 109 0 327
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 438 87 0
V1 Done 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad MLD Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Wrong Version : 0
Lcl-Scope Packets : 0
Rsvd-Scope Packets : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
MCAC Policy Drops : 0
MCS Failures : 0
MVR From VPLS Cfg Drops : 0
MVR To SAP Cfg Drops : 0
===============================================================================
*A:rbae_C#
statistics
Syntax
statistics [evpn-mpls | sap sap-id | sdp sdp-id:vc-id | vxlan vtep ip-address vni vni]
Context
[Tree] (show>service>id>igmp-snooping statistics)
Full Context
show service id igmp-snooping statistics
Description
This command displays IGMP snooping statistics for the VPLS service.
Parameters
- evpn-mpls
-
Displays IGMP snooping statistics for EVPN-MPLS destinations
- sap-id
-
Displays IGMP snooping statistics for a specific SAP
- sdp-id
-
Displays the IGMP snooping statistics for a specific spoke or mesh SDP
- vc-id
-
The virtual circuit ID on the SDP ID for which to display information
- vxlan vtep ip-address vni <1..16777215>
-
Displays the IGMP snooping entries associated with a specific VXLAN binding, given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI). This parameter only applies to the 7450 ESS or 7750 SR.
- vni
-
The VXLAN Network Identifier (VNI) for which to display information. This parameter only applies to the 7450 ESS or 7750 SR.
Platforms
All
Output
Output Example*A:ALA-1>show>service>id>snooping# statistics
===============================================================================
IGMP Snooping Statistics for service 1
===============================================================================
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 4 0 4
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 0 0 0
V3 Reports 0 0 0
V2 Leaves 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad IP Checksum : 0
Bad IGMP Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
MVR From VPLS Cfg Drops : 0
MVR To SAP Cfg Drops : 0
===============================================================================
*A:ALA-1>show>service>id>snooping#
statistics
Syntax
statistics [ip-int-name | ip-address]
statistics group-interface [fwd-service service-id] [ip-int-name]
statistics host [ip-address]
Context
[Tree] (show>router>igmp statistics)
Full Context
show router igmp statistics
Description
This command displays IGMP statistics information.
Parameters
- ip-int-name
-
Displays information associated with the specified IP interface name, up to 32 characters.
- ip-address
-
Displays information associated with the specified IP address.
Platforms
All
Output
The following output is an example of IGMP statistics information. Output fields: IGMP statistics provides statistical IGMP field descriptions.
Output Example*A:ALA-BA# show router igmp interface "IGMP_to_CE"
==================================================
IGMP Interface IGMP_to_CE Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 0
Report V1 0 0
Report V2 0 0
Report V3 0 0
Leaves 0 0
--------------------------------------------------
Interface General Statistics
--------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Drops : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
MCAC Policy Drops : 0
--------------------------------------------------
Interface Source Group Statistics
--------------------------------------------------
(S,G) : 0
(*,G) : 0
==================================================
*A:ALA-BA#
*B:Dut-C# show router igmp statistics host
==================================================
IGMP Host Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 1739
Report V1 0 0
Report V2 0 0
Report V3 10 0
Leaves 0 0
-------------------------------------------------------------------------------
General Host Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Bad Receive If : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
MCAC Policy Drops : 0
==================================================
*B:Dut-C#
|
Label |
Description |
|---|---|
|
IGMP Interface Statistics |
Lists the IGMP statistics for a particular interface. |
|
Message Type |
Queries — The number of IGMP general queries transmitted or received on this interface. |
|
Report — The total number of IGMP V1, V2, or V3 reports transmitted or received on this interface. |
|
|
Leaves — The total number of IGMP leaves transmitted on this interface. |
|
|
Received |
The total number of IGMP packets received on this interface. |
|
Transmitted |
The total number of IGMP packets transmitted from this interface. |
|
General Interface Statistics |
The general IGMP statistics. |
|
Bad Length |
The total number of IGMP packets with bad length received on this interface. |
|
Bad Checksum |
The total number of IGMP packets with bad checksum received on this interface. |
|
Unknown Type |
The total number of IGMP packets with unknown type received on this interface. |
|
Drops |
The total number of IGMP packets dropped on this interface. |
|
Rx Non Local |
The total number of IGMP packets received from a non-local sender. |
|
Rx Wrong Version |
The total number of IGMP packets with wrong versions received on this interface. |
|
Policy Drops |
The total number of IGMP packets dropped by import policies on this interface. |
|
No Router Alert |
The total number of IGMPv3 packets received on this interface which did not have the router alert flag set. |
|
Rx Bad Encodings |
The total number of IGMP packets with bad encodings received on this interface. |
|
Rx Pkt Drops |
The total number of IGMP receive packet drops on this interface. |
|
Local Scope Pkts |
The total number of IGMP packets with local scope received on this interface. |
|
Resvd Scope Pkts |
The total number of IGMP packets with reserved scope received on this interface. |
|
MCAC Policy Drops |
The total number of IGMP packets dropped by MCAC policies on this interface. |
statistics
Syntax
statistics all
statistics sap sap-id
statistics sdp sdp-id:vc-id
statistics vxlan vtep ip-address vni vni-id
Context
[Tree] (clear>service>id>mld-snooping statistics)
Full Context
clear service id mld-snooping statistics
Description
This command clears MLD snooping statistics.
Parameters
- sap-id
-
Clears MLD snooping statistics for the specified SAP.
- sdp-id
-
Clears MLD snooping statistics associated with the specified SDP. For a spoke-SDP, the VC ID must be specified; for a mesh SDP, the VC ID is optional.
- vni-id
-
Clears the MLD snooping statistics for the specified VXLAN VNI id.
- ip-address
-
Specifies a specific configured static egress VTEP to clear the MLD snooping statistics associated only with the VTEP.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>service>id>authentication statistics)
Full Context
clear service id authentication statistics
Description
This command clears session authentication statistics for this service.
Platforms
All
statistics
Syntax
statistics {evpn-mpls | all | sap sap-id | sdp sdp-id:vc-id | vxlan vtep ip-address vni vni-id}]
Context
[Tree] (clear>service>id>igmp-snooping statistics)
Full Context
clear service id igmp-snooping statistics
Description
This command clears IGMP snooping statistics for the VPLS service.
Parameters
- all
-
Clears the IGMP snooping information for all port objects in the service
- evpn-mpls
-
Clears IGMP snooping statistics for EVPN-MPLS destinations
- sap-id
-
Clears the IGMP snooping information on the specified SAP
- sdp-id
-
Clears only IGMP snooping entries associated with the specified mesh SDP or spoke-SDP. For a spoke-SDP, the VC ID must be specified, for a mesh SDP, the VC ID is optional.
- vc-id
-
Clears statistics for the specified virtual circuit ID on the SDP ID
- vxlan vtep ip-address vni <1..16777215>
-
Clears the IGMP snooping statistics associated with a specific VXLAN destination given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI). This parameter only applies to the 7450 ESS or 7750 SR.
- vni-id
-
Displays information for the specified VXLAN Network Identifier (VNI). This parameter only applies to the 7450 ESS or 7750 SR.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>subscr-mgmt>wlan-gw statistics)
Full Context
show subscriber-mgmt wlan-gw statistics
Description
This command displays statistics information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (show>service>id>spb statistics)
Full Context
show service id spb statistics
Description
This command displays SPB statistics.
Platforms
All
Output
The following output is an example of service SPB statistics information.
Output ExampleA:cses-B01# show service id spb statistics
===============================================================================
ISIS Statistics
===============================================================================
ISIS Instance : 1024 SPF Runs : 4
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 31 31 0 9 0
IIH 532 532 0 533 0
CSNP 479 479 0 479 0
PSNP 9 9 0 27 0
Unknown 0 0 0 0 0
===============================================================================
statistics
Syntax
statistics [sap sap-id] [ sdp sdp-id:vc-id] [family]
Context
[Tree] (show>service>id>pim-snooping statistics)
Full Context
show service id pim-snooping statistics
Description
This command displays PIM statistics information.
Parameters
- sap-id
-
Displays the statistics associated with the specified SAP
- sdp-id:vc-id
-
Displays the statistics associated with the specified SDP
- family
-
Displays either IPv4 or IPv6 statistics
Platforms
All
Output
The following output is an example of service PIM snooping statistics information.
Output Example*A:PE# show service id 1 pim-snooping statistics
=================================================================
PIM Snooping Statistics ipv4
=================================================================
Message Type Received Transmitted Rx Errors
-----------------------------------------------------------------
Hello 36 - 0
Join Prune 8 8 0
Total Packets 44 8
-------------------------------------------------------------------------------
General Statistics
-------------------------------------------------------------------------------
Rx Neighbor Unknown : 0
Rx Bad Checksum Discard : 0
Rx Bad Encoding : 0
Rx Bad Version Discard : 0
Join Policy Drops : 0
-------------------------------------------------------------------------------
Source Group Statistics
-------------------------------------------------------------------------------
(S,G) : 1
(*,G) : 0
=================================================================
*A:PE#
statistics
Syntax
statistics {all | ipv4 | ipv6 | mac}
statistics group grp-address
Context
[Tree] (clear>service>id>mfib statistics)
Full Context
clear service id mfib statistics
Description
This command clears multicast FIB statistics for the VPLS service.
Parameters
- all
-
Clears all statistics for the service ID
- ipv4
-
Clears IPv4 address statistics for the service ID
- ipv6
-
Clears IPv6 address statistics for the service ID
- mac
-
Clears MAC address statistics for the service ID
- grp-address
-
Specifies an IGMP multicast group address that receives data on an interface
Platforms
All
statistics
Syntax
statistics [evpn-mpls | sap sap-id | sdp sdp-id:vc-id | vxlan vtep ip-address vni vni-id] [family]
Context
[Tree] (clear>service>id>pim-snooping statistics)
Full Context
clear service id pim-snooping statistics
Description
This command clears PIM snooping statistics for the specified SAP or SDP.
Parameters
- sap-id
-
Clears PIM snooping statistics for the specified SAP
- sdp-id:vc-id
-
Clears PIM statistics for the specified SDP. For a spoke-SDP, the VC ID must be specified; for a mesh SDP, the VC ID is optional.
- family
-
Displays either IPv4 or IPv6 information
- evpn-mpls
-
Clears PIM snooping statistics for EVPN-MPLS destinations
Platforms
All
statistics
Syntax
statistics [summary] [sap sap-id]
Context
[Tree] (show>service>id>host-connectivity-verify statistics)
Full Context
show service id host-connectivity-verify statistics
Description
This command displays host connectivity verification statistics.
Parameters
- sap-id
-
Specifies the SAP ID to show statistics for.
- summary
-
Displays host connectivity verify summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of host connectivity verification statistics information, and Output fields: host connectivity verify statistics describes the output fields.
Output ExampleA:ALA-48>show>service>id# host-connectivity-verify statistics sap 1/1/9:0
==============================================================================
Host connectivity check statistics
==============================================================================
Svc SapId/ DestIp Last Time Oper
Id SdpId Address Response Expired State
------------------------------------------------------------------------------
1000 551/2/3:0 10.144.145.1 Up
==============================================================================
A:ALA-48>show>service>id#
|
Label |
Description |
|---|---|
|
Svc Id |
The service identifier. |
|
SapId/SdpId |
The SAP and SDP identifiers. |
|
DestIp Address |
The destination IP address. |
|
Last Response |
The time when the last response was received. |
|
Time Expired |
Displays whether the interval value has expired. |
|
Oper State |
Displays the current operational state of the service. |
statistics
Syntax
statistics
Context
[Tree] (show>router>vrrp statistics)
Full Context
show router vrrp statistics
Description
This command displays statistics for VRRP instance.
Platforms
All
Output
The following output is an example of VRRP statistics information, and table describes the fields.
Output ExampleA:ALA-48# show router vrrp statistics
===============================================================================
VRRP Global Statistics
===============================================================================
VR Id Errors : 0 Version Errors : 0
Checksum Errors : 0
===============================================================================
|
Label |
Description |
|---|---|
|
VR Id Errors |
Displays the number of virtual router ID errors |
|
Version Errors |
Displays the number of version errors |
|
Checksum Errors |
Displays the number of checksum errors |
statistics
Syntax
statistics
statistics interface interface-name [vrid virtual-router-id]
statistics interface interface-name vrid virtual-router-id ipv6
Context
[Tree] (clear>router>vrrp statistics)
Full Context
clear router vrrp statistics
Description
This command clears statistics for VRRP instances on an IP interface or VRRP priority control policies.
Parameters
- interface-name
-
Clears the VRRP statistics for all VRRP instances on the specified IP interface.
- virtual-router-id
-
Clears the VRRP statistics for the specified VRRP instance on the IP interface.
- ipv6
-
Clears IPv6 statistics for the specified interface.
Platforms
All
statistics
Syntax
statistics [ip-addr | ip-int-name]
Context
[Tree] (show>router>rip statistics)
Full Context
show router rip statistics
Description
Display Interface level statistics for the RIP protocol.
If no IP address or interface name is specified, then all configured RIP interfaces are displayed.
If an IP address or interface name is specified, then only data regarding the specified RIP interface is displayed.
Parameters
- ip-addr | ip-int-name
-
Displays statistics for the specified IP interface.
Platforms
All
Output
The following output is an example of RIP statistics information, and Output fields: RIP statistics describes the output fields.
Output ExampleRIP Statistics
===============================================================================
Learned Routes : 0 Timed Out Routes : 0
Current Memory : 120624 Maximum Memory : 262144
-------------------------------------------------------------------------------
Interface "to-web"
-------------------------------------------------------------------------------
Primary IP : 10.1.1.3 Update Timer : 30
Timeout Timer : 180 Flush Timer : 120
Counter Total Last 5 Min Last 1 Min
------------------------------------------------------------------------------
Updates Sent 0 0 0
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
RIPv1 Updates Received 0 0 0
RIPv1 Updates Ignored 0 0 0
RIPv1 Bad Routes 0 0 0
RIPv1 Requests Received 0 0 0
RIPv1 Requests Ignored 0 0 0
RIPv2 Updates Received 0 0 0
RIPv2 Updates Ignored 0 0 0
RIPv2 Bad Routes 0 0 0
RIPv2 Requests Received 0 0 0
RIPv2 Requests Ignored 0 0 0
Authentication Errors 0 0 0
==============================================================================
*A:ALA-12#
|
Label |
Description |
|---|---|
|
Learned Routes |
The number of RIP-learned routes exported to RIP neighbors. |
|
Timed Out Routes |
The number of routes that have been timed out. |
|
Current Memory |
The amount of memory used by this RIP router instance. |
|
Maximum Memory |
The amount of memory allocated for this RIP router instance. |
|
Interface |
Displays the name of each interface configured in RIP and associated RIP statistics. |
|
Primary IP |
The interface IP address. |
|
Update Timer |
The current setting of the RIP update timer value expressed in seconds. |
|
Timeout Timer |
The current RIP timeout timer value expressed in seconds. |
|
Flush Timer |
The number of seconds after a route has been declared invalid that it is flushed from the route database. |
|
Updates Sent |
Total — The total number of RIP updates that were sent. Last 5 Min — The number of RIP updates that were sent in the last 5 minutes. Last 1 Min — The number of RIP updates that were sent in the last 1 minute. |
|
Triggered Updates |
Total — The total number of triggered updates sent. These updates are sent before the entire RIP routing table is sent. Last 5 Min — The number of triggered updates that were sent in the last 5 minutes. Last 1 Min — The number of triggered updates that were sent in the last 1 minute. |
|
Bad Packets Received |
Total — The total number of RIP updates received on this interface that were discarded as invalid. Last 5 Min — The number of RIP updates received on this interface that were discarded as invalid in the last 5 minutes. Last 1 Min —The number of RIP updates received on this interface that were discarded as invalid in the last 1 minute. |
|
RIPv1 Updates Received |
Total — The total number of RIPv1 updates received. Last 5 Min — The number of RIPv1 updates received in the last 5 minutes. Last 1 Min — The number of RIPv1 updates received in the last 1 minute. |
|
RIPv1 Updates Ignored |
Total — The total number of RIPv1 updates ignored. Last 5 Min — The number of RIPv1 updates ignored in the last 5 minutes. Last 1 Min — The number of RIPv1 updates ignored in the last 1 minute. |
|
RIPv1 Bad Routes |
Total — The total number of bad routes received from the peer. Last 5 Min — The number of bad routes received from the peer in the last 5 minutes. Last 1 Min — The number of bad routes received from the peer in the last minute. |
|
RIPv1 Requests Received |
Total — The total number of times the router received RIPv1 route requests from other routers. Last 5 Min — The number of times the router received RIPv1 route requests from other routers in the last 5 minutes. Last 1 Min — The number of times the router received RIPv1 route requests from other routers in the last 1 minute. |
|
RIPv1 Requests Ignored |
Total — The total number of times the router ignored RIPv1 route requests from other routers. Last 5 Min — The number of times the router ignored RIPv1 route requests from other routers in the last 5 minutes. Last 1 Min — The number of times the router ignored RIPv1 route requests from other routers in the last 1 minute. |
|
RIPv2 Updates Received |
Total — The total number of RIPv2 updates received. Last 5 Min — The number of RIPv2 updates received in the last 5 minutes. Last 1 Min — The number of RIPv2 updates received in the last minute. |
|
RIPv2 Updates Ignored |
Total — The total number of RIPv2 updates ignored. Last 5 Min — The number of RIPv2 updates ignored in the last 5 minutes. Last 1 Min — The number of RIPv2 updates ignored in the last minute. |
|
RIPv2 Bad Routes |
Total — The total number of bad routes received from the peer. Last 5 Min — The number of bad routes received from the peer in the last 5 minutes. Last 1 Min — The number of bad routes received from the peer in the last minute. |
|
RIPv2 Requests Received |
Total — The total number of times the router received RIPv2 route requests from other routers. Last 5 Min — The number of times the router received RIPv2 route requests from other routers in the last 5 minutes. Last 1 Min — The number of times the router received RIPv2 route requests from other routers in the last minute. |
|
RIPv2 Requests Ignored |
Total — The total number of times the router ignored RIPv2 route requests from other routers. Last 5 Min — The number of times the router ignored RIPv2 route requests from other routers in the last 5 minutes. Last 1 Min —The number of times the router ignored RIPv2 route requests from other routers in the last minute. |
|
Authentication Errors |
Total — The total number of authentication errors to secure table updates. Last 5 Min — The number of authentication errors to secure table updates in the last 5 minutes. Last 1 Min —The number of authentication errors to secure table updates in the last minute. |
statistics
Syntax
statistics [neighbor {ip-address | ip-int-name}]
Context
[Tree] (clear>router>rip statistics)
Full Context
clear router rip statistics
Description
This command clears statistics for RIP neighbors.
Parameters
- {ip-address | ip-int-name}
-
Clears the statistics for the specified RIP interface.
Platforms
All
statistics
Syntax
statistics [neighbor {ip-int-name | ip-address}]
Context
[Tree] (clear>router>ripng statistics)
Full Context
clear router ripng statistics
Description
This command clears statistics for RIPng neighbors.
Parameters
- {ip-int-name | ip-address}
-
Clears the statistics for the specified RIPng interface.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>ldp statistics)
Full Context
show router ldp statistics
Description
This command displays LDP instance statistics related information.
Platforms
All
Output
Output Example*A:Dut-A# show router ldp statistics
===============================================================================
LDP Statistics for IPv4 LSR ID 10.20.1.1:0
IPv6 LSR ID 3ffe::a14:101[0]
===============================================================================
Session/Discovery
-------------------------------------------------------------------------------
Active IPv4 Sess : 3 Active IPv6 Sess : 3
Active IPv4 LinkAdj: 2 Active IPv6 LinkAdj : 2
Active IPv4 TargAdj: 1 Active IPv6 TargAdj : 1
Active IPv4 If : 2 Inactive IPv4 If : 0
Active IPv6 If : 2 Inactive IPv6 If : 0
Active IPv4 Peers : 1 Inactive IPv4 Peers : 0
Active IPv6 Peers : 1 Inactive IPv6 Peers : 0
IPv4 Attempted Sess: 0 IPv6 Attempted Sess : 0
IPv4 OLoad If : 0 IPv4 OLoad Targ Peers: 0
IPv6 OLoad If : 0 IPv6 OLoad Targ Peers: 0
-------------------------------------------------------------------------------
Protocol Stats
-------------------------------------------------------------------------------
No Hello Err : 0 Param Adv Err : 0
Max PDU Err : 0 Label Range Err : 0
Bad LDP Id Err : 0 Bad PDU Len Err : 0
Bad Mesg Len Err : 0 Bad TLV Len Err : 0
Unknown TLV Err : 0 Bad Proto Ver Err : 0
Malformed TLV Err : 0 Keepalive Expired Err: 0
Shutdown Notif Sent: 0 Shutdown Notif Recv : 0
-------------------------------------------------------------------------------
Prefixes
-------------------------------------------------------------------------------
IPv4 Pfx FECs Sent : 10 IPv4 Pfx FECs Recv : 10
IPv6 Pfx FECs Sent : 10 IPv6 Pfx FECs Recv : 10
IPv4PfxFecOLSessSnt: 0 IPv4PfxFecOLSessRecv : 0
IPv6PfxFecOLSessSnt: 0 IPv6PfxFecOLSessRecv : 0
IPv4PfxFecInOLoad : 0 IPv6PfxFecInOLoad : 0
-------------------------------------------------------------------------------
P2MP
-------------------------------------------------------------------------------
IPv4 P2MP FECs Sent: 0 IPv4 P2MP FECs Recv : 0
IPv6 P2MP FECs Sent: 0 IPv6 P2MP FECs Recv : 0
IPv4P2MPFecOLSessSn: 0 IPv4P2MPFecOLSessRecv: 0
IPv6P2MPFecOLSessSn: 0 IPv6P2MPFecOLSessRecv: 0
IPv4P2MPFecInOLoad : 0 IPv6P2MPFecInOLoad : 0
-------------------------------------------------------------------------------
Services
-------------------------------------------------------------------------------
Svc FEC128s Sent : 0 Svc FEC128s Recv : 0
Svc FEC129s Sent : 0 Svc FEC129s Recv : 0
Svc Fec128 OLSessSn: 0 Svc Fec128 OLSessRecv: 0
Svc Fec129 OLSessSn: 0 Svc Fec129 OLSessRecv: 0
Svc Fec128 InOLoad : 0 Svc Fec129 InOLoad : 0
===============================================================================
statistics
Syntax
statistics
Context
[Tree] (clear>router>ldp statistics)
Full Context
clear router ldp statistics
Description
This command clears LDP instance statistics.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>rsvp statistics)
Full Context
show router rsvp statistics
Description
This command displays global statistics in the RSVP instance.
Platforms
All
Output
The following output is an example of RSVP statistics information.
Output fields: RSVP statistics describes RSVP statistics output fields.
|
Label |
Description |
|---|---|
|
PATH Timeouts |
The total number of path timeouts. |
|
RESV Timeouts |
The total number of RESV timeouts. |
*A:SR1# /show router rsvp statistics
===============================================================================
RSVP Global Statistics
===============================================================================
PATH Timeouts : 0 RESV Timeouts : 0
GR Helper PATH Tim*: 0 GR Helper RESV Tim*: 0
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:SRU4>show>router>rsvp# statistics
===============================================================================
RSVP Global Statistics
===============================================================================
PATH Timeouts : 1026 RESV Timeouts : 182
===============================================================================
*A:SRU4>show>router>rsvp#
statistics
Syntax
statistics lsp-ldp head ip-prefix/prefix-length src-ip ip-address
statistics lsp-ldp tail ip-prefix/prefix-length dst-ip ip-address
statistics src-ip ip-address dst-ip ip-address
statistics all
statistics src-ip ip-address dst-ip ip-address lsp-rsvp {head | tail} tunnel-id [0..4294967295] lsp-id [0..4294967295]
statistics mpls-tp lsp-name path {working | protect}
statistics p2mp-interface interface-name
statistics src-ip ip-address lsp-rsvp {head | tail} rsvp-session-name [256 chars max]
Context
[Tree] (clear>router>bfd statistics)
Full Context
clear router bfd statistics
Description
This command clears BFD statistics.
Parameters
- all
-
Clears all statistics for the BFD instance.
- dst-ip ip-address
-
Clears statistics about the specified destination IPv4 or IPv6 address.
- ip-prefix/prefix-length
-
Clears statistics for the specified IP prefix.
- lsp-id [0..4294967295]
-
Clears statistics about the specified LSP ID.
- lsp-ldp head
-
Clears statistics for the head of the LSP LDP link.
- lsp-ldp tail
-
Clears statistics for the tail of the LSP LDP link.
- lsp-rsvp {head | tail}
-
Clears statistics about the specified link type.
- mpls-tp lsp-name
-
Clears statistics about the specified MPLS TP LSP.
- p2mp-interface interface-name
-
Clears statistics about the specified P2MP interface.
- path {working | protect}
-
Clears statistics about the working or protect path.
- rsvp-session-name [256 chars max]
-
Clears statistics about the specified RSVP session.
- src-ip ip-address
-
Clears statistics about the specified source IPv4 or IPv6 address.
- tunnel-id [0..4294967295]
-
Clears statistics about the specified tunnel ID.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>router>rsvp statistics)
Full Context
clear router rsvp statistics
Description
This command clears global statistics for the RSVP instance, for example, clears path and resv timeout counters.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>isa statistics)
Full Context
show isa statistics
Description
Commands in this context display ISA statistical information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (clear>video statistics)
Full Context
clear video statistics
Description
This command clears video related statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-s
statistics
Syntax
statistics
Context
[Tree] (show>router>bier statistics)
Full Context
show router bier statistics
Description
This command displays BIER statistics.
Platforms
All
statistics
Syntax
statistics group-interface [fwd-service service-id] ip-in-name
statistics group-interface all
statistics host ip-address
statistics host all
statistics [interface ip-int-name | ip-address]
Context
[Tree] (clear>router>igmp statistics)
Full Context
clear router igmp statistics
Description
This command clears IGMP statistics on a specified interface or IP address.
An interface, group, and source cannot be specified at the same time.
Parameters
- group-interface interface-name
-
Clears the IGMP statistics on the specified group interface.
- group-interface all
-
Clears the IGMP statistics on all group interfaces.
- service-id
-
Specifies the service ID.
- host ip-address
-
Clears the IGMP statistics on the specified host.
- host all
-
Clears the IGMP statistics on all hosts.
- interface ip-int-name
-
Clears the IGMP statistics on the specified interface.
- interface ip-address
-
Clears the IGMP statistics on the specified IP address.
Platforms
All
statistics
Syntax
statistics policy policy-name [bundle bundle-name] [ protocol {igmp | pim | igmpSnpg | mld}]
statistics
Context
[Tree] (show>router>mcac statistics)
Full Context
show router mcac statistics
Description
This command displays MCAC statistics.
Parameters
- policy-name
-
Specifies an existing multicast CAC (MCAC) policy name.
- bundle-name
-
Displays statistics for the specified existing multicast bundle name.
- protocol {igmp | pim | igmpSnpg | mld}
-
Displays statistics for the specified applicable protocol.
Platforms
All
statistics
Syntax
statistics [ip-int-name | ipv6-address]
statistics ipsec-interface ip-int-name
Context
[Tree] (show>router>mld statistics)
Full Context
show router mld statistics
Description
This command displays MLD statistics information.
Parameters
- ip-int-name
-
Displays information associated with the specified IP interface name, up to 32 characters.
- ipv6-address
-
Displays information associated with the specified IPv6 address.
- ipsec-interface ip-int-name
-
Displays information associated with the specified dynamic name for the MLD-enabled child_SA.
Platforms
All
Output
The following output is an example of MLD statistics information. Output fields: MLD statistics provides statistical MLD field descriptions.
Output Example*A:ALA-BA# show router mld statistics
==================================================
MLD Interface Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 9
Report V1 0 0
Report V2 0 0
Dones 0 0
-------------------------------------------------------------------------------
General Interface Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Bad Receive If : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Rx Pkt Drops : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
MCAC Policy Drops : 0
-------------------------------------------------------------------------------
Source Group Statistics
-------------------------------------------------------------------------------
(S,G) : 0
(*,G) : 5
==================================================
*A:Dut-A#
|
Label |
Description |
|---|---|
|
MLD Interface Statistics |
The MLD statistics for a particular interface. |
|
Message Type |
Queries — The number of MLD general queries transmitted or received on this interface. Report — The total number of MLD V1 or V2 reports transmitted or received on this interface. Dones — The total number of MLD dones transmitted on this interface. |
|
Received |
The total number of MLD packets received on this interface. |
|
Transmitted |
The total number of MLD packets transmitted from this interface. |
|
General Interface Statistics |
The general MLD statistics. |
|
Bad Length |
The total number of MLD packets with bad length received on this interface. |
|
Bad Checksum |
The total number of MLD packets with bad checksum received on this interface. |
|
Unknown Type |
The total number of MLD packets with unknown type received on this interface. |
|
Bad Receive If |
The total number of MLD packets incorrectly received on this interface. |
|
Rx Non Local |
The total number of MLD packets received from a non-local sender. |
|
Rx Wrong Version |
The total number of MLD packets with wrong versions received on this interface. |
|
Policy Drops |
The total number of MLD packets dropped by import policies on this interface. |
|
No Router Alert |
The total number of MLD packets received on this interface which did not have the router alert flag set. |
|
Rx Bad Encodings |
The total number of MLD packets with bad encodings received on this interface. |
|
Rx Pkt Drops |
The total number of MLD receive packet drops on this interface. |
|
Local Scope Pkts |
The total number of MLD packets with local scope received on this interface. |
|
Resvd Scope Pkts |
The total number of MLD packets with reserved scope received on this interface. |
|
MCAC Policy Drops |
The total number of MLD packets dropped by MCAC policies on this interface. |
statistics
Syntax
statistics group-interface [fwd-service service-id] ip-int-name
statistics group-interface all
statistics host ipv6-address
statistics host all
statistics [ip-int-name | ipv6-address]
statistics ipsec-interface ip-int-name
Context
[Tree] (clear>router>mld statistics)
Full Context
clear router mld statistics
Description
This command clears MLD statistics parameters.
Parameters
- service-id
-
Clears the MLD statistics for the service ID.
- group-interface interface-name
-
Clears the MLD statistics on the specified group interface.
- group-interface all
-
Clears the MLD statistics on all group interfaces.
- host all
-
Clears the MLD statistics on all hosts.
- host ipv6-address
-
Clears the MLD statistics on the specified host.
- ip-int-name
-
Clears statistics for the specified MLD interface name.
- ipv6-address
-
Clears statistics for the specified MLD IPv6 address.
- ipsec-interface ip-int-name
-
Clears statistics information for the specified dynamic name for the MLD-enabled child_SA.
Platforms
All
statistics
Syntax
statistics [peer ip-address]
Context
[Tree] (show>router>msdp statistics)
Full Context
show router msdp statistics
Description
This command displays statistics information related to a MSDP peer.
Parameters
- ip-address
-
Displays information about the specified peer IP address.
Platforms
All
Output
The following output is an example of MSDP statistics information, and Output fields: MSDP statistics describes the output fields.
Output exampleA:ALA-48# show router msdp statistics
===============================================================================
MSDP Statistics
===============================================================================
Glo ActSrc Lim Excd: 0
-------------------------------------------------------------------------------
Peer Address : 10.20.1.1
-------------------------------------------------------------------------------
Last State Change : 0d 11:33:16 Last message Peer : 0d 00:00:17
RPF Failures : 0 Remote Closes : 0
SA Msgs Sent : 0 SA Msgs Recvd : 709
SA req. Msgs Sent : 0 SA req. Msgs Recvd : 0
SA res. Msgs Sent : 0 SA res. Msgs Recvd : 0
KeepAlive Msgs Sent: 694 KeepAlive Msgs Recd: 694
Unknown Msgs Sent : 0 Error Msgs Recvd : 0
-------------------------------------------------------------------------------
Peers : 1
===============================================================================
A:ALA-48#
|
Label |
Description |
|---|---|
| Glo ActSrc Lim Excd | The number of times the active source limit was exceeded across all MSDP sessions |
| Peer address | The IP address of the peer |
|
Last State Change |
The date and time the peer state changed |
|
RPF Failures |
The number of reverse path forwarding (RPF) failures |
|
SA Msgs Sent |
The number of SA messages sent |
|
SA req. Msgs Sent |
The number of SA request messages sent |
|
SA res. Msgs Sent |
The number of SA response messages sent |
|
KeepAlive Msgs Sent |
The number of keepalive messages sent |
|
Unknown Msgs Sent |
The number of unknown messages received |
|
Last message Peer |
The time the last message was received from the peer |
|
Remote Closes |
The number of times the remote peer close |
|
SA Msgs Recvd |
The number of SA messages received |
|
SA req. Msgs Recvd |
The number of SA request messages received |
|
SA res. Msgs Recvd |
The number of SA response messages received |
|
KeepAlive Msgs Recd |
The number of keepalive messages received |
|
Error Msgs Recvd |
The number of unknown messages received |
statistics
Syntax
statistics [peer ip-address]
Context
[Tree] (clear>router>msdp statistics)
Full Context
clear router msdp statistics
Description
This command clears IP address statistics of the peer to which Multicast Source Discovery Protocol (MSDP) source-active (SA) requests for groups matching this entry's group range were sent.
Parameters
- ip-address
-
Clears the statistics of the specified IP address.
Platforms
All
statistics
Syntax
statistics [ip-int-name | mt-int-name | ip-address | mpls-if-name] [family]
Context
[Tree] (show>router>pim statistics)
Full Context
show router pim statistics
Description
This command displays statistics for a particular PIM instance.
Parameters
- ip-int-name
-
Displays interface information associated with the specified IP interface name.
- mt-int-name
-
Displays information about the default core group address of the Multicast Distribution Tree (MDT) for the VPRN instance. The Multicast Tunnel (MT) interface for a VPRN is created when this object is set to a valid group address.
Syntax: vprn-id-mt-grp-ip-address
- ip-address
-
Displays interface information associated with the specified IP address.
- mpls-if-name
-
Displays information about the specified MPLS interface name.
Syntax: mpls-if-index
- family
-
Displays statistics information for the specified family.
Platforms
All
Output
The following output is an example of PIM statistics information. Output fields: PIM statistics provides PIM statistics output field descriptions
Output ExampleA:ALA-1# show router pim statistics
=================================================================
PIM Statistics ipv4
=================================================================
Message Type Received Transmitted Rx Errors
-----------------------------------------------------------------
Hello 18009 12834 0
Join Prune 9135 1129 10
Core RPFV JP 0 0 0
MVPN RPFV JP 0 0 0
Asserts 0 0 0
Register 0 0 0
Null Register 0 0 0
Register Stop 0 0 0
BSM 0 0 0
Candidate RP Adv 0 0 0
Auto-RP Announce 2049 0 0
Auto-RP Mapping 2066 0 0
PIM DM Grafts 0 0 0
PIM DM Graft Acks 0 0 0
Total Packets 31231 13963
-----------------------------------------------------------------
Intra-AS AD 0 0 0
Inter-AS AD 0 0 0
Mdt-Safi 1323 10 0
S-PMSI AD 0 0 0
Leaf AD 0 0 0
Source-Active AD 0 0 0
Shared Tree Join 0 0 0
Source Tree Join 0 0 0
Total BGP Packets 1323 10
-------------------------------------------------------------------------------
General Statistics
-------------------------------------------------------------------------------
Rx Invalid Register : 0
Rx Neighbor Unknown : 10
Rx Bad Checksum Discard : 0
Rx Bad Encoding : 0
Rx Bad Version Discard : 0
Rx CRP No Router Alert : 0
Rx BSM Router Alert Drops : 0
Rx BSM Wrong If Drops : 0
Rx Invalid Join Prune : 0
Rx Invalid Auto-RP PDU : 0
RPF Mismatch Auto-RP Mapping PDU : 65
RPF Mismatch Auto-RP Announce PDU : 80
Rx Unknown PDU Type : 0
Join Policy Drops : 0
Register Policy Drops : 0
Bootstrap Import Policy Drops : 0
Bootstrap Export Policy Drops : 0
Mcac Policy Drops : 0
Fwd Candidate RP Adv : 0
Fwd Candidate RP Adv Drops : 0
S-pmsi Join TLV PDUs txd. : 0
S-pmsi Join TLV PDUs rcd. : 0
S-pmsi Join TLV PDUs txd. Drops : 0
S-pmsi Join TLV PDUs rcd. Drops : 0
S-pmsi Maximum-P2mp-Spmsi Hits : 0
P2mp Pmsi Create Failures : 0
P2mp Pmsi Request Failures : 0
PDU Drops on Non-PIM/Down Intf : 0
Active Tx S-pmsis : 0
Active Tx MS-pmsis : 0
Active Rx S-pmsis : 0
Active Rx Pseudo S-pmsis : 0
Total Tx S-pmsis : 0
Total Rx S-pmsis : 0
-------------------------------------------------------------------------------
Source Group Statistics
-------------------------------------------------------------------------------
(S,G) : 2
(*,G) : 2
(*,*,RP) : 0
================================================================
|
Label |
Description |
|---|---|
|
PIM Statistics |
The section listing the PIM statistics for a particular interface |
|
Message Type |
The type of message. Hello — The number of PIM hello messages received or transmitted Join Prune — The number of PIM join prune messages received or transmitted Asserts — The number of PIM assert messages received or transmitted Register — The number of register messages received or transmitted Null Register — The number of PIM null register messages received or transmitted Register Stop — The number of PIM register stop messages received or transmitted BSM — The number of PIM Bootstrap messages (BSM) received or transmitted Candidate RP Adv — The number of candidate RP advertisements Auto-RP Announce — The number of auto-RP announce (224.0.1.39) messages received or transmitted Auto-RP Mapping — The number of auto-RP mapping (224.0.1.40) messages received or transmitted |
|
Message Type |
PIM DM Grafts — The number of PIM graft messages received or transmitted PIM DM Graft Acks — The number of PIM graft acknowledgment messages received or transmitted Total Packets — The total number of packets transmitted and received. |
|
Received |
The number of messages received |
|
Transmitted |
The number of multicast data packets transmitted |
|
Rx Errors |
The total number of receive errors |
|
General Interface Statistics |
The section listing the general PIM interface statistics |
|
Register TTL Drop |
The number of multicast data packets which could not be encapsulated in Register messages because the time to live (TTL) was zero |
|
Tx Register MTU Drop |
The number of Bootstrap messages received on this interface but were dropped |
|
Rx Invalid Register |
The number of invalid PIM register messages received |
|
Rx Neighbor Unknown |
The number of PIM messages (other than hello messages) which were received and were rejected because the adjacency with the neighbor router was not already established |
|
Rx Bad Checksum Discard |
The number of PIM messages received, and which were discarded because of bad checksum |
|
Rx Bad Encoding |
The number of PIM messages with bad encodings received |
|
Rx Bad Version Discard |
The number of PIM messages with bad versions received |
|
Rx CRP No Router Alert |
The number of candidate-rp advertisements (C-RP-Adv) received, and which had no router alert option set |
|
Rx Invalid Join Prune |
The number of invalid PIM join prune messages received |
|
Rx Unknown PDU Type |
The number of packets received with an unsupported PIM type |
|
Join Policy Drops |
The number of times the join policy match resulted in dropping PIM join-prune message or one of the source group contained in the message |
|
Register Policy Drops |
The number of times the register policy match resulted in dropping PIM register message |
|
Bootstrap Import Policy Drops |
The number of Bootstrap messages received that were dropped because of Bootstrap import policy |
|
Bootstrap Export Policy Drops |
The number of Bootstrap messages that were not transmitted because of Bootstrap export policy. |
|
Source Group Statistics |
The section listing the source group statistics |
|
(S,G) |
The number of entries in which the type is (S,G) |
|
(*,G) |
The number of entries in which the type is (*,G) |
|
(*,*,RP) |
The number of entries in which the type is (*, *, rp) |
statistics
Syntax
statistics [family]
statistics [interface ip-int-name | mt-int-name | int-ip-address] [family]
statistics [group grp-ip-address] [source ip-address] [family]
Context
[Tree] (clear>router>pim statistics)
Full Context
clear router pim statistics
Description
This command clears PIM statistics on a specified interface or IP address.
An interface and group or source cannot be specified at the same time.
Parameters
- ip-int-name
-
Clears PIM statistics on the specified interface.
- ip-address
-
Clears PIM statistics on the specified IP address.
- mt-int-name
-
Clears the default core group address of the Multicast Distribution Tree (MDT) for the VPRN instance. The Multicast Tunnel (MT) interface for a VPRN is created when this object is set to a valid group address.
syntax: vprn-id-mt-grp-ip-address
- grp-ip-address
-
When only the group address is specified and no source is specified, (*,G) statistics are cleared. When the group address is specified along with the source address, then the (S,G) statistics are reset to zero.
- ip-address
-
When the source address is specified along with the group address, then the (S,G) statistics are reset to zero.
- family
-
Clears statistics family information.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>p2mp-sr-tree statistics)
Full Context
show router p2mp-sr-tree statistics
Description
This command displays P2MP SR tree statistics.
Platforms
All
Output
The following output is an example of P2MP SR tree statistics information.
The "Programming failures” count in tree SID statistics are not High Availability (HA) compatible and are reset upon an activity switch of the CPMs.
A:node-2>show>router>p2mp-sr-tree# statistics
============================================================
P2MP-SR Statistics
============================================================
General
Total Number of p2mp-policies : 2
static : 2
pce : 0
sr-policy : 0
Total Number candidate-paths : 2
static : 2
pce : 0
sr-policy : 0
Total Number replication-segments : 4
static : 4
pce : 0
sr-policy : 0
Total Number downstream-nodes : 2
static : 2
pce : 0
sr-policy : 0
Total Number push : 2
Total Number swap : 1
Total Number pop : 1
Total Number tunnel-allocated : 2
Total Number downstream-node interfaces
inService : 1
outOfService : 0
unsupported : 0
mismatched : 0
without BFD : 0
BackPressure
DataPlane backpressure active : disabled
DataPlane backpressure count : 0
Errors
Unknown Originator Owner : 0
Duplicate TreeIds : 0
Programming failures
NhIdx : 0
Labels : 0
Tunnels : 0
Protection Grp : 0
===============================================================================
P2MP Policies
===============================================================================
Policy-Name
RootAddr TreeId State NumPaths
Tunnel Active-Path
Candidate-Path Origin ASN PLSP-ID
State Create-Time Preference Desc
-------------------------------------------------------------------------------
p2mp_policy_8193_10.20.1.3
10.20.1.3 8193 inService 1
73740 cp_1
cp_1 static 0 --
inService 1d 02:25:09 0 1
p2mp_policy_8194_10.20.1.3
10.20.1.3 8194 inService 1
73745 cp_1
cp_1 static 0 --
inService 1d 02:25:10 0 1
-------------------------------------------------------------------------------
Total P2MP Policies : 2
===============================================================================
statistics
Syntax
statistics
Context
[Tree] (show>eth-cfm statistics)
Full Context
show eth-cfm statistics
Description
This command displays the ETH-CFM statistics counters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of ETH-CFM statistics information. Output fields: ETH-CFM statistics describes the ETH-CFM statistics fields.
Output Exampleshow eth-cfm statistics
===============================================================================
ETH-CFM System Statistics
===============================================================================
Rx Count : 10513196 Tx Count : 2294783
Dropped Congestion : 0 Discarded Error : 764766
AIS Currently Act : 0 AIS Currently Fail : 0
===============================================================================
=================================
ETH-CFM System Op-code Statistics
=================================
Op-code Rx Count Tx Count
---------------------------------
ccm 4588504 2294779
lbr 0 0
lbm 2 0
ltr 0 1
ltm 1 0
ais 0 0
lck 0 0
tst 0 0
laps 0 0
raps 0 0
mcc 0 0
lmr 0 0
lmm 0 0
1dm 0 0
dmr 0 0
dmm 4012644 0
exr 0 0
exm 0 0
csf 0 0
vsr 0 0
vsm 0 0
1sl 0 0
slr 0 0
slm 1912045 0
other 0 0
---------------------------------
Total 10513196 2294780
=================================
|
Label |
Description |
|---|---|
|
Rx Count |
The ETH-CFM CPU receive rate, in PPS |
|
Tx Count |
The ETH-CFM CPU transmit rate, in PPS |
|
Dropped Congestion |
The number of valid or supported ETH-CFM packets not processed by the CPU as a result of resource contention |
|
Discard Error |
The number of ETH-CFM packets that did not pass validation |
statistics
Syntax
statistics session session-name dm meas-interval { 5-mins | 15-mins | 1-hour | 1-day | raw} interval-number interval-number [ all | bins | summary]
statistics session session-name dmm meas-interval { 5-mins | 15-mins | 1-hour | 1-day | raw} interval-number interval-number [ all | bins | summary]
statistics session session-name lmm meas-interval { 5-mins| 15-mins| 1-hour| 1-day| raw} interval-number interval-number
statistics session session-name slm meas-interval { 5-mins| 15-mins| 1-hour| 1-day| raw} interval-number interval-number
statistics session session-name twamp-light meas-interval { 5-mins | 15-mins | 1-hour | 1-day | raw} interval-number interval-number delay [ all | bins | summary]
Context
[Tree] (show>oam-pm statistics)
Full Context
show oam-pm statistics
Description
This command shows the delay statistics for the specified test using the parameters specified.
Parameters
- session-name
-
Identifies the session to be queried.
- dm
-
Specifies that the delay test is from the MPLS test family and is using dm style measurements for the delay.
- dmm
-
Specifies that the delay test is from the Ethernet test family and is using dmm style measurements for the delay.
- lmm
-
Specifies the loss test is from the Ethernet test family and is using lmm style measurements for the loss.
- slm
-
Specifies that the loss test is from the Ethernet test family and is using slm style measurements for the loss.
- twamp-light
-
Specifies that the delay test is from the IP test family and is using twamp-light style measurements for the delay.
- meas-interval
-
Identifies the measurement interval to query for the statistics. When raw is specified, the interval number is not to be included because there is only one raw cumulative bin.
- interval-number
-
Specifies the numerical reference that indicates the position from the latest sample window. The number 1 is the most recent with all higher numbers being that position in the past from current.
- [all | bins | summary]
-
Specifies a keyword to filter the output.
- delay
-
Indicates that the statistics being queried are for delay. TWAMP-Light PDUs carry both delay and loss informational elements and it is not clear from only the test type name which statistic the operator requires.
- loss
-
Indicates the statistics being queried are for loss. TWAMP-Light PDUs carry both delay and loss informational elements and it is not clear from only the test type name which statistic the operator requires. This keyword is specific to twamp-light.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>eth-cfm statistics)
Full Context
clear eth-cfm statistics
Description
This command clears the eth-cfm statistics counters maintained in clearEthCfmStatistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
statistics interface {ip-int-name | ip-address}
statistics policy name
Context
[Tree] (show>router>authentication statistics)
Full Context
show router authentication statistics
Description
This command displays interface or policy authentication statistics.
Parameters
- ip-int-name | ip-address
-
Specifies an existing interface name or IP address.
- name
-
Specifies an existing policy name.
Platforms
All
Output
Authentication Statistics Output — The following output is an example of authentication statistics, and Output fields: authentication statistics describes the fields.
Output ExampleA:ALU-3>show>router>auth# statistics
===================================================================
Authentication Global Statistics
===================================================================
Client Packets Authenticate Fail : 0
Client Packets Authenticate Ok : 12
===================================================================
|
Label |
Description |
|---|---|
|
Client Packets Authenticate Fail |
The number of packets that failed authentication |
|
Client Packets Authenticate Ok |
The number of packets that were authenticated |
statistics
Syntax
statistics [interface ip-int-name | ip-address]
Context
[Tree] (clear>router>authentication statistics)
Full Context
clear router authentication statistics
Description
This command clears authentication statistics.
Parameters
- ip-int-name
-
Clears the authentication statistics for the specified interface name. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
- ip-address
-
Clears the authentication statistics for the specified IP address.
Platforms
All
statistics
Syntax
statistics [policy policy-id]
Context
[Tree] (clear>vrrp statistics)
Full Context
clear vrrp statistics
Description
Commands in this context clear and reset VRRP entities.
Parameters
- policy-id
-
Clears statistics for the specified policy.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>system>ptp statistics)
Full Context
show system ptp statistics
Description
This command displays the message and error statistics for the node.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of PTP statistics information, and Output fields: system PTP statistics describes the output fields.
Output Example# show system ptp statistics
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
PTP Packets 0 0
Announce 0 0
Sync 0 0
Follow Up 0 0
Delay Request 0 0
Delay Response 0 0
Signaling 0 0
Request Unicast Transmission TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Grant Unicast Transmission (Accepted) TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Grant Unicast Transmission (Denied) TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Cancel Unicast Transmission TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Ack Cancel Unicast Transmission TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Other TLVs 0 0
Other 0 0
Event Packets timestamped at port 0 0
Event Packets timestamped at cpm 0 0
Discards 0 0
Bad PTP domain 0 0
Alternate Master 0 0
Out Of Sequence 0 0
Peer Disabled 0 0
Packet Timing Signal Fail - Unusable 0 0
maxStepsRemoved exceeded 0 0
Other 0 0
===============================================================================
===============================================================================
IEEE 1588/PTP Frequency Recovery State Statistics
===============================================================================
State Seconds
-------------------------------------------------------------------------------
Initial 0
Acquiring 0
Phase-Tracking 0
Locked 0
Hold-over 0
===============================================================================
===============================================================================
IEEE 1588/PTP Event Statistics
===============================================================================
Event Sync Flow Delay Flow
-------------------------------------------------------------------------------
Packet Loss 0 0
Excessive Packet Loss 0 0
Excessive Phase Shift Detected 0 0
Too Much Packet Delay Variation - Freq 0 0
Too Much Packet Delay Variation - Time
===============================================================================
===============================================================================
IEEE 1588/PTP Clock Time Recovery State Statistics
===============================================================================
State Seconds
-------------------------------------------------------------------------------
Initial 1280
Acquiring 63
Locked 0
Hold-over 0
===============================================================================
===============================================================================
IEEE 1588/PTP Message Rates Per Second
===============================================================================
UDP/IP Ethernet
Packet Type Input Output Input Output
-------------------------------------------------------------------------------
Announce 0 0 0 0
Sync 0 0 0 0
Follow Up 0 0 0 0
Delay Request 0 0 0 0
Delay Response 0 0 0 0
Other 0 0 0 0
-------------------------------------------------------------------------------
Total 0 0 0 0
===============================================================================
|
Counter |
Counts |
|
|---|---|---|
|
PTP Packets (packet type) |
Input |
The number of input packets for the specified packet type |
|
Output |
The number of output packets for the specified packet type |
|
|
Discards (reason type) |
Input |
The number of discarded input packets for the specified reason |
|
Output |
The number of discarded output packets for the specified reason |
|
|
State (state type) |
Seconds |
The number of seconds for the specified state type |
|
Event (event type) |
Sync Flow |
The number of sync flows for the specified event type |
|
Delay Flow |
The number of delay flows for the specified event type |
|
|
Packet Type (packet type) |
UDP/IP Input/Output |
The number of UDP/IP input or output packets for the specified packet type |
|
Ethernet Input/Output |
The number of Ethernet input or output packets for the specified packet type |
|
statistics
Syntax
statistics
Context
[Tree] (clear>application-assurance>group statistics)
Full Context
clear application-assurance group statistics
Description
This command clears application assurance statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (clear>redundancy>multi-chassis>mcr statistics)
Full Context
clear redundancy multi-chassis mc-ring statistics
Description
This command clears multi-chassis ring.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>system>ptp statistics)
Full Context
clear system ptp statistics
Description
This command clears all PTP statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
Context
[Tree] (clear>system statistics)
Full Context
clear system statistics
Description
This command clears system specific statistics.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>certificate statistics)
Full Context
show certificate statistics
Description
This command shows certificate related statistics.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>isis statistics)
Full Context
show router isis statistics
Description
This command displays information regarding IS-IS traffic statistics.
Platforms
All
Output
The following output is an example of IS-IS statistics output.
Output Example*A:Dut-C# show router isis statistics
===============================================================================
Rtr Base ISIS Instance 0 Statistics
===============================================================================
ISIS Instance : 0
Purge Initiated : 0 LSP Regens. : 17
Sid SRGB err : 0 Sid dupl err : 0
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
SPF Statistics
SPF Runs : 7
Last runTimeStamp: 01/26/2015 11:22:50
Partial SPF Runs : 3
Last runTimeStamp: 01/26/2015 11:22:51
LFA Statistics
LFA Runs : 7
Last runTimeStamp: 01/26/2015 11:22:51
Partial LFA Runs : 3
Last runTimeStamp: 01/26/2015 11:22:41
RLFA Statistics
RLFA Runs : 10
Last runTimeStamp: 01/26/2015 11:22:51
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 164 164 0 151 0
IIH 146 146 0 147 0
CSNP 288 288 0 291 0
PSNP 71 71 0 74 0
Unknown 0 0 0 0 0
===============================================================================
*A:Dut-C#
Output fields: IS-IS statistics describes IS-IS statistics output fields.
|
Label |
Description |
|---|---|
|
Purge Initiated |
The number of times purges have been initiated. |
|
SPF Runs |
The number of times shortest path first calculations have been made. |
|
LSP Regens |
The count of LSP regenerations. |
|
Requests |
The number of CSPF requests made to the protocol. |
|
Paths Found |
The number of responses to CSPF requests for which paths satisfying the constraints were found. |
|
PDU Type |
The PDU type. |
|
Received |
The count of link state PDUs received by this instance of the protocol. |
|
Processed |
The count of link state PDUs processed by this instance of the protocol. |
|
Dropped |
The count of link state PDUs dropped by this instance of the protocol. |
|
Sent |
The count of link state PDUs sent out by this instance of the protocol. |
|
Retransmitted |
The count of link state PDUs that had to be retransmitted by this instance of the protocol. |
statistics
statistics
Syntax
statistics
Context
[Tree] (show>router>ospf statistics)
[Tree] (show>router>ospf3 statistics)
Full Context
show router ospf statistics
show router ospf3 statistics
Description
This command displays the global OSPF statistics.
Platforms
All
Output
The following output is an example of global OSPF statistic information and Output fields: OSPF statistics describes the output fields.
Output Exampleshow router ospf statistics
===============================================================================
Rtr Base OSPFv2 Instance 0 Statistics
===============================================================================
Rx Packets : 441 Tx Packets : 463
Rx Hellos : 361 Tx Hellos : 371
Rx DBDs : 9 Tx DBDs : 7
Rx LSRs : 3 Tx LSRs : 3
Rx LSUs : 54 Tx LSUs : 72
Rx LS Acks : 14 Tx LS Acks : 10
New LSAs Recvd : 57 New LSAs Orig : 8
Ext LSAs Count : 0 No of Areas : 1
No of Interfaces : 4 No of Neighbors : 3
Discards : 3 Tx Failures : 3
Retransmits : 2
Bad Networks : 0 Bad Virt Links : 0
Bad Areas : 0 Bad Dest Addrs : 0
Bad Auth Types : 0 Auth Failures : 0
Bad Neighbors : 0 Bad Pkt Types : 0
Bad Lengths : 0 Bad Hello Int. : 2
Bad Dead Int. : 1 Bad Options : 0
Bad Versions : 0 Bad Checksums : 0
SID SRGB errors : 0 SID dupl errors : 0
Failed SPF Attempts : 0 Bad MTUs : 0
CSPF Requests : 0 CSPF Request Drops : 0
CSPF Path Found : 0 CSPF Path Not Found : 0
Total SPF Runs : 6 Total LFA SPF Runs : 0
Total RLFA SPF Runs : 0 Total TI-LFA SPF Runs: 0
===============================================================================
show router ospf3 statistics
===============================================================================
Rtr Base OSPFv3 Instance 0 Statistics
===============================================================================
Rx Packets : 525 Tx Packets : 564
Rx Hellos : 387 Tx Hellos : 387
Rx DBDs : 8 Tx DBDs : 7
Rx LSRs : 3 Tx LSRs : 3
Rx LSUs : 113 Tx LSUs : 156
Rx LS Acks : 14 Tx LS Acks : 11
New LSAs Recvd : 77 New LSAs Orig : 12
Ext LSAs Count : 0 No of Areas : 1
No of Interfaces : 4 No of Neighbors : 3
Discards : 0 Tx Failures : 0
Retransmits : 0
Bad Networks : 0 Bad Virt Links : 0
Bad Areas : 0 Bad Dest Addrs : 0
Bad Auth Types : 0 Auth Failures : 0
Bad Neighbors : 0 Bad Pkt Types : 0
Bad Lengths : 0 Bad Hello Int. : 0
Bad Dead Int. : 0 Bad Options : 0
Bad Versions : 0 Bad Checksums : 0
SID SRGB errors : 0 SID dupl errors : 0
Failed SPF Attempts : 0 Bad MTUs : 0
CSPF Requests : 0 CSPF Request Drops : 0
CSPF Path Found : 0 CSPF Path Not Found : 0
Total SPF Runs : 7 Total LFA SPF Runs : 0
Total RLFA SPF Runs : 0 Total TI-LFA SPF Runs: 0
===============================================================================
|
Label |
Description |
|---|---|
|
Rx Packets |
The total number of OSPF packets received on all OSPF enabled interfaces. |
|
Tx Packets |
The total number of OSPF packets transmitted on all OSPF enabled interfaces. |
|
Rx Hellos |
The total number of OSPF Hello packets received on all OSPF enabled interfaces. |
|
Tx Hellos |
The total number of OSPF Hello packets transmitted on all OSPF enabled interfaces. |
|
Rx DBDs |
The total number of OSPF database description packets received on all OSPF enabled interfaces. |
|
Tx DBDs |
The total number of OSPF database description packets transmitted on all OSPF enabled interfaces |
|
Rx LSRs |
The total number of OSPF Link State Requests (LSRs) received on all OSPF enabled interfaces. |
|
Tx LSRs |
The total number of OSPF Link State Requests (LSRs) transmitted on all OSPF enabled interfaces. |
|
Rx LSUs |
The total number of OSPF Link State Update (LSUs) received on all OSPF enabled interfaces. |
|
Tx LSUs |
The total number of OSPF Link State Update (LSUs) transmitted on all OSPF enabled interfaces. |
|
Rx LS Acks |
The total number of OSPF Link State Acknowledgments (LSAs) received on all OSPF enabled interfaces. |
|
New LSAs Recvd |
The total number of new OSPF Link State Advertisements received on all OSPF enabled interfaces. |
|
New LSAs Orig |
The total number of new OSPF Link State Advertisements originated on all OSPF enabled interfaces. |
|
Ext LSAs Count |
The total number of OSPF External Link State Advertisements. |
|
No of Areas |
The number of areas configured for this OSPF instance. |
|
Total SPF Runs |
The total number of incremental SPF runs triggered by new or updated LSAs. |
|
Ext SPF Runs |
The total number of incremental SPF runs triggered by new or updated type-5 external LSAs. |
|
Retransmits |
The total number of OSPF Retransmits transmitted on all OSPF enabled interfaces. |
|
Discards |
The total number of OSPF packets discarded on all OSPF enabled interfaces. |
|
Bad Networks |
The total number of OSPF packets received on all OSPF enabled interfaces with invalid network or mask. |
|
Bad Virt Links |
The total number of OSPF packets received on all OSPF enabled interfaces that are destined to a virtual link that does not exist. |
|
Bad Areas |
The total number of OSPF packets received on all OSPF enabled interfaces with an area mismatch. |
|
Bad Dest Addrs |
The total number of OSPF packets received on all OSPF enabled interfaces with the incorrect IP destination address. |
|
Bad Auth Types |
The total number of OSPF packets received on all OSPF enabled interfaces with an invalid authorization type. |
|
Auth Failures |
The total number of OSPF packets received on all OSPF enabled interfaces with an invalid authorization key. |
|
Bad Neighbors |
The total number of OSPF packets received on all OSPF enabled interfaces where the neighbor information does not match the information this router has for the neighbor. |
|
Bad Pkt Types |
The total number of OSPF packets received on all OSPF enabled interfaces with an invalid OSPF packet type. |
|
Bad Lengths |
The total number of OSPF packets received on all OSPF enabled interfaces with a total length not equal to the length given in the packet itself. |
|
Bad Hello Int. |
The total number of OSPF packets received on all OSPF enabled interfaces where the hello interval given in packet was not equal to that configured for the respective interface. |
|
Bad Dead Int. |
The total number of OSPF packets received on all OSPF enabled interfaces where the dead interval given in the packet was not equal to that configured for the respective interface. |
|
Bad Options |
The total number of OSPF packets received on all OSPF enabled interfaces with an option that does not match those configured for the respective interface or area. |
|
Bad Versions |
The total number of OSPF packets received on all OSPF enabled interfaces with bad OSPF version numbers. |
|
Tx Failures |
Transmitted OSPF packets that are dropped due to resource shortage. |
statistics
Syntax
statistics
Context
[Tree] (clear>router>ospf statistics)
[Tree] (clear>router>ospf3 statistics)
Full Context
clear router ospf statistics
clear router ospf3 statistics
Description
This command clears all neighbor, router, interface, SPF and global statistics of this OSPF instance.
Platforms
All
statistics
Syntax
statistics [ipv6-address | ip-int-name]
Context
[Tree] (show>router>ripng statistics)
Full Context
show router ripng statistics
Description
This command displays the interface level statistics for the RIPng protocol.
If no IPv6 address or interface name is specified, then all configured RIPng interfaces are displayed.
If an IPv6 address or interface name is specified, then only data regarding the specified RIPng interface is displayed.
Parameters
- ipv6-address | ip-int-name
-
Displays statistics for the specified IPv6 interface.
Platforms
All
Output
The following output are examples of RIPng statistics information.
Output Example*A:Dut-C>config>router>if# show router ripng statistics
===============================================================================
RIP-NG Statistics
===============================================================================
Learned Routes : 40 Timed Out Routes : 0
Current Memory : 1,199,016 Maximum Memory : 2,097,152
-------------------------------------------------------------------------------
Interface "one"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:3:3/1* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 221 180 5
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 225 185 3
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
-------------------------------------------------------------------------------
Interface "two"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:103:3* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 220 183 5
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 229 183 5
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
-------------------------------------------------------------------------------
Interface "three"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:12:3/* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 224 184 6
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 221 182 4
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
-------------------------------------------------------------------------------
Interface "four"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:112:3* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 220 182 8
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 227 185 4
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C>config>router>if# show router ripng statistics "one"
===============================================================================
RIP-NG Statistics
===============================================================================
Learned Routes : 40 Timed Out Routes : 0
Current Memory : 1,199,016 Maximum Memory : 2,097,152
-------------------------------------------------------------------------------
Interface "one"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:3:3/1* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 224 183 8
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 230 190 8
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
===============================================================================
* indicates that the corresponding row element may have been truncated.
statistics
Syntax
statistics
statistics manager all
statistics manager manager-name
Context
[Tree] (clear>system>management-interface>remote-management statistics)
Full Context
clear system management-interface remote-management statistics
Description
This command clears the statistics for remote management managers. If the command is run without specifying the manager, the statistics for all remote managers are cleared.
Parameters
- manager
-
Keyword to specify that clears statistics only for a specific manager.
- manager-name
-
Specifies the configured name of the manager, up to 64 characters, for which the statistics are cleared.
- all
-
Clears statistics for all managers.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>subscr-mgmt>pfcp statistics)
Full Context
show subscriber-mgmt pfcp statistics
Description
This command displays the packet counters for each PFCP message and upstream IBCP message.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PFCP statistics information.
Output ExampleA:BNG-UPF# show subscriber-mgmt pfcp statistics
===============================================================================
PFCP System Statistics
===============================================================================
PFCP Session Related Messages
Session Establish Req : 3 Session Establish Resp : 3
Session Establish Resp fail: 0
Session Modify Req : 2 Session Modify Resp : 2
Session Modify Resp fail : 0
Session Deletion Req : 1 Session Deletion Resp : 1
Session Deletion Resp fail : 0
Session Report Req : 1 Session Report Resp : 1
Session Report Resp fail : 0
Session Report DDR Req : 0 Session Report DDR Rsp : 0
Session Report DDR Rsp fail: 0
Session Report UR Req : 0 Session Report UR Rsp : 0
Session Report UR Rsp fail : 0
Session Report EIR Req : 0 Session Report EIR Rsp : 0
Session Report EIR Rsp fail: 0
Session Report UPIR Req : 1 Session Report UPIR Rsp : 1
Session Report UPIR Rs fail: 0
PFCP Session Audit Related Messages
Session Modify Req : 0 Session Modify Resp : 0
Session Modify Resp fail : 0
Session Report Req : 0 Session Report Rsp : 0
Session Report Rsp fail : 0
PFCP Node Related Messages
Node Report Req : 0 Node Report Resp : 0
Node Report Resp fail : 0
Assoc Setup Req Rx : 0 Assoc Setup Resp Rx : 1
Assoc Setup Resp fail Rx : 0
Assoc Setup Req Tx : 1 Assoc Setup Resp Tx : 0
Assoc Setup Resp fail Tx : 0
Assoc Upd Req Rx : 0 Assoc Upd Resp Rx : 0
Assoc Upd Resp fail Rx : 0
Assoc Upd Req Tx : 0 Assoc Upd Resp Tx : 0
Assoc Upd Resp fail Tx : 0
Assoc Upd Req with ARR : 0 Assoc Upd Req with GRP : 0
Assoc Upd Req ARR & GRP : 0
Assoc Release Req : 0 Assoc Release Resp : 0
Assoc Release Resp fail : 0
Heartbeat Req Rx : 417 Heartbeat Resp Rx : 1
Heartbeat Req Tx : 1 Heartbeat Resp Tx : 417
Heartbeat Aud Trig Req Tx : 0 Heartbeat Aud Trig Rsp Rx : 0
Heartbeat Aud Start Req Rx : 0 Heartbeat Aud Start Rsp Tx : 0
Heartbeat Aud End Req Rx : 0 Heartbeat Aud End Rsp Tx : 0
IBCP upstream packet statistics
Ipoe Rx Pkts : 0
Pppoe Ctrl Rx Pkts : 10
Pppoe Data Rx Pkts : 16
Tx Pkts to Smf : 26
IBCP upstream packet discard statistics
Missing pkt detection rule : 0
Default tnl trigger missing: 0
Default tunnel missing : 0
Parsing error : 0
Tx error : 0
IBCP default tunnel
overwrite : 0
Number of PFCP Sessions : 2
-------------------------------------------------------------------------------
===============================================================================statistics
Syntax
statistics lsp-path [lsp-index lsp-index] [path-lspid path-lspid ][prefix ip-prefix/prefix-length] [ src ip-address | ipv6 address]
statistics lsp-path all
statistics sr-policy [lsp-index lsp-index] [path-lspid path-lspid] [prefix ip-prefix/prefix-length] [ src ip-address | ipv6 address]
statistics sr-policy all
Context
[Tree] (clear>router>bfd>seamless-bfd statistics)
Full Context
clear router bfd seamless-bfd statistics
Description
This command clears BFD statistics.
Parameters
- lsp-path
-
Keyword to clear the S-BFD statistics for LSP path.
- sr-policy
-
Keyword to clear the S-BFD statistics for SR policy.
- all
-
Keyword to clear all S-BFD statistics.
- lsp-index lsp-index
-
Specifies the LSP index.
- path-lspid path-lspid
-
Specifies the path LSP ID.
- prefix
-
Keyword to clear information by far-end prefix.
- ip-prefix/prefix-length
-
Specifies an IP prefix for which to clear S-BFD statistics, and the length of the prefix.
- ip-address | ipv6-address
-
Specifies the IP address for which to clear S-BFD statistics.
Platforms
All
statistics
Syntax
statistics [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>router>isis statistics)
Full Context
monitor router isis statistics
Description
This command displays statistical IS-IS traffic information at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified router statistics. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of ISIS statistics.
Output ExampleA:ALA-12>monitor>router>isis# statistics interval 3 repeat 2 absolute
===============================================================================
ISIS Statistics
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 74 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 74 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 74 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
===============================================================================
A:ALA-12>monitor>router>isis# statistics interval 3 repeat 2 rate
===============================================================================
ISIS Statistics
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 76 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 0
Purge Initiated : 0 LSP Regens. : 0
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 0 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 0
Purge Initiated : 0 LSP Regens. : 0
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 1 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
===============================================================================
A:ALA-12>monitor>router>isis#
statistics
Syntax
statistics [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>router>ldp statistics)
Full Context
monitor router ldp statistics
Description
Monitor statistics for LDP instance at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the LDP statistics. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of LDP statistics information.
Output ExampleA:ALA-12>monitor>router>ldp# statistics interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for LDP instance
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
===============================================================================
A:ALA-12>monitor>router>ldp#
A:ALA-12>monitor>router>ldp# statistics interval 3 repeat 3 rate
===============================================================================
Monitor statistics for LDP instance
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 0 Serv FECs Recv : 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 0 Serv FECs Recv : 0
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Rate)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 0 Serv FECs Recv : 0
===============================================================================
A:ALA-12>monitor>router>ldp#
statistics
Syntax
statistics [interval seconds] [ repeat repeat] [absolute| rate]
Context
[Tree] (monitor>eth-cfm statistics)
Full Context
monitor eth-cfm statistics
Description
This command monitors control plane traffic statistics.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics all
statistics neighbor ip-address [port port-number]
Context
[Tree] (clear>service>id>gsmp statistics)
Full Context
clear service id gsmp statistics
Description
This command clears General Switch Management Protocol (GSMP) statistics.
Parameters
- all
-
Clears all GSMP related statistics.
- ip-address
-
Specifies the IP address.
- port-number
-
Specifies port number.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>system>ptp>port statistics)
Full Context
clear system ptp port statistics
Description
This command clears PTP port statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
Context
[Tree] (clear>service>id>subhosts statistics)
Full Context
clear service id subscriber-hosts statistics
Description
This command clears subscriber host HTTP redirect statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (show>li>x-interfaces statistics)
Full Context
show li x-interfaces statistics
Description
Commands in this context display statistics of the X1, X2, and X3 interfaces.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
Context
[Tree] (clear>router>bier statistics)
Full Context
clear router bier statistics
Description
This command clears BIER statistics.
Platforms
All
statistics
Syntax
statistics [policy policy-name]
Context
[Tree] (clear>router>mcac statistics)
Full Context
clear router mcac statistics
Description
This command clears and resets MCAC statistics.
Parameters
- policy-name
-
Specifies the policy name, up to 32 characters.
Platforms
All
statistics
Syntax
statistics [portal name] [ all-portals]
Context
[Tree] (clear>router>wpp statistics)
Full Context
clear router wpp statistics
Description
This command clears WPP statistics.
Parameters
- portal-name
-
Specifies the portal name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (clear>router>autoconfigure>rtr-adv statistics)
Full Context
clear router autoconfigure router-advertisement statistics
Description
This command clears router-advertisement statistics.
Platforms
7450 ESS-7, 7750 SR-1, 7750 SR-7, 7750 SR-1e, 7750 SR-2e, 7750 SR-s
statistics
Syntax
statistics
Context
[Tree] (clear>system>management-interface>netconf>call-home>all-client statistics)
Full Context
clear system management-interface netconf call-home all-client statistics
Description
This command resets statistics for all NETCONF call-home clients.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>system>management-interface>netconf>listen statistics)
Full Context
clear system management-interface netconf listen statistics
Description
This command resets NETCONF listen server statistics.
Platforms
All