VXLAN v4

VXLAN on SR Linux uses a tunnel model where VXLAN interfaces are bound to network instances, in the same way that subinterfaces are bound to network instances. Up to one VXLAN interface per network instance is supported.

Configuration of VXLAN on SR Linux is tied to EVPN. VXLAN configuration consists of the following steps:

1. Configure a tunnel interface and VXLAN interface.

   A tunnel interface for VXLAN is configured as vxlan<N>, where N can be 0 to 255.

   A VXLAN interface is configured under a tunnel interface. At a minimum, a VXLAN interface must have an index, type, and the ingress VXLAN network identifier (VNI).

   • The index can be a number in the range 0 to 4294967295.

   • The type can be bridged or routed and indicates whether the vxlan-interface can be linked to a MAC-VRF (bridged) or IP-VRF (routed).

   • The system looks for the ingress VNI in incoming VXLAN packets to classify them to this VXLAN interface and its network instance.

   Configuration of an explicit VXLAN interface egress source IP is not permitted, given that the data path supports one source tunnel IP address for all VXLAN interfaces. The source IP used in the VXLAN interfaces is the IPv4 address of sub-interface system0.0 in the default network instance.

2. Associate the VXLAN interface to a network instance.

   A VXLAN interface can only be associated with one network instance, and a network instance can have only one VXLAN interface.

3. Associate the VXLAN interface to a BGP-EVPN instance.

   The VXLAN interface must be linked to a BGP-EVPN instance so that VXLAN destinations can be dynamically discovered and used to forward traffic.

The following configuration example shows these steps:

tunnel-interface vxlan1 {
  // (Step 1) Creation of the tunnel-interface and vxlan-interface
    vxlan-interface 1 {
        type bridged
        ingress {
            vni 1
        }
        egress {
            source-ip use-system-ipv4-address
        }
    }
}
network-instance blue {
    type mac-vrf
    admin-state enable
    description "network instance blue"
    interface ethernet-1/2.1 {
    }
    vxlan-interface vxlan1.1 {
  // (Step 2) Association of the vxlan-interface to the network-instance
    }
    protocols {
        bgp-evpn {
            bgp-instance 1 {
                admin-state enable
                vxlan-interface vxlan1.1
  // (Step 3) Association of the vxlan-interface to the bgp-evpn instance
                evi 1
            }
        }
        bgp-vpn {
            bgp-instance 1 {
                route-distinguisher {
                    route-distinguisher 1.1.1.1:1
                }
                route-target {
                    export-rt target:1234:1
                    import-rt target:1234:1
                }
            }
        }
    }
}

When EVPN routes are received with VXLAN encapsulation, the SR Linux creates VXLAN Termination Endpoints (VTEPs) from the EVPN route next-hops, and each VTEP is allocated an index number (per source and destination tunnel IP addresses).

When a VTEP is created in the vxlan-tunnel table and a non-zero index allocated, a tunnel-table entry is also created for the tunnel in the tunnel-table.

If the next hop is not resolved to any route in the network-instance default route-table, the index in the vxlan-tunnel table shows as 0 for the VTEP, and no tunnel-table entry would be created in the tunnel-table for that VTEP.

The following example shows the created vxlan-tunnel entries and tunnel-table entries on reception of IMET routes from three different PEs.

--{ [FACTORY] + candidate shared default }--[  ]--
# info from state tunnel vxlan-tunnel vtep *
    tunnel {
        vxlan-tunnel {
            vtep 10.22.22.2 {
                index 677716962894
 // index allocated per source and destination tunnel IP addresses.
 Index of 0 would mean that 10.22.22.2 is not resolved in the route-table
 and no tunnel-table entry is created.
                last-change "17 hours ago"
            }
            vtep 10.33.33.3 {
                index 677716962900
                last-change "17 hours ago"
            }
            vtep 10.44.44.4 {
                index 677716962897
                last-change "17 hours ago"
            }
        }
    }

--{ [FACTORY] + candidate shared default }--[  ]--
# info from state network-instance default tunnel-table ipv4
    network-instance default {
        tunnel-table {
            ipv4 {
                tunnel 10.22.22.2/32 type vxlan owner vxlan_mgr id 1 {
  // tunnel table entry for VTEP 10.22.22.2, created
 after the vxlan-tunnel vtep 10.22.22.2
                    next-hop-group 677716962900 // NHG-ID allocated by fib_mgr
                    metric 0
                    preference 0
                    last-app-update "17 hours ago"
                    vxlan {
                        destination-address 10.22.22.2
                        source-address 10.11.11.1
                        time-to-live 255
                    }
                }
                tunnel 10.33.33.3/32 type vxlan owner vxlan_mgr id 3 {
                    next-hop-group 677716962900
                    metric 0
                    preference 0
                    last-app-update "17 hours ago"
                    vxlan {
                        destination-address 10.33.33.3
                        source-address 10.11.11.1
                        time-to-live 255
                    }
                }
                tunnel 10.44.44.4/32 type vxlan owner vxlan_mgr id 2 {
                    next-hop-group 677716962897
                    metric 0
                    preference 0
                    last-app-update "17 hours ago"
                    vxlan {
                        destination-address 10.44.44.4
                        source-address 10.11.11.1
                        time-to-live 255
                    }
                }
            }
        }
    }

--{ [FACTORY] + candidate shared default }--[  ]--
# info from state network-instance default route-table next-hop-group 677716962900
    network-instance default {
        route-table {
            next-hop-group 677716962900 {
                next-hop 0 {
                    next-hop 677716962900
 // NH ID allocated by fib_mgr for the NHG-ID
                    active true
                }
            }
        }
    }

--{ [FACTORY] + candidate shared default }--[  ]--
# info from state network-instance default route-table next-hop 677716962900
    network-instance default {
        route-table {
            next-hop 677716962900 {
 // resolution of the NH ID
                type direct
                ip-address 10.1.2.2
                subinterface ethernet-1/1.1
            }
        }
    }

Unicast traffic forwarded to VXLAN destinations can be load-balanced on network (underlay) ECMP links or overlay aliasing destinations.

Network LAGs, that is, LAG subinterfaces in the default network instance, are not supported when VXLAN is enabled on the platform. LAG access subinterfaces on MAC-VRFs are supported.

VXLAN-originated packets support double spraying based on overlay ECMP (or aliasing) and underlay ECMP on the default network instance.

Load-balancing is supported for the following:

• encapsulated Layer 2 unicast frames (coming from a subinterface within the same broadcast domain)

• Layer 3 frames coming from an IRB subinterface

For BUM frames, load balancing operates as follows:

• BUM supports spraying in access LAGs based on a hash. That is, BUM flows received from a VXLAN or a Layer 2 subinterface of a MAC-VRF are sprayed across egress access LAG links.

• BUM does not support spraying in underlay VXLAN next-hops. That is, BUM flows received from VXLAN or a Layer 2 subinterface of a MAC-VRF are sent to a single underlay subinterface.

• BUM VXLAN packets are sent to a single member of the next-hop group (NHG) associated with a specific VXLAN multicast destination. The chosen member is based on a hash of the NHG-ID of the VXLAN destination and the number of links in the NHG.

You can configure system filter ACLs to drop incoming VXLAN packets for reasons such as the following:

• the source IP is not recognized

• the destination IP is not an address to be used for termination

• the default destination UDP port is not being used

SR Linux supports logging VXLAN of packets dropped by ACL policies.

A system filter ACL is an IPv4 or IPv6 ACL that is evaluated before tunnel termination has occurred and before interface ACLs have been applied. A system filter can match and drop unauthorized VXLAN tunnel packets before they are decapsulated. When a system filter ACL is created, its rules are evaluated against all transit and terminating IPv4 or IPv6 traffic that is arriving on any subinterface of the router, regardless of where that traffic entered in terms of network instance, subinterface, and so on.

The system filter matches the outer header of tunneled packets; they do not filter the payload of VXLAN tunnels. If the system-filter does not drop the VXLAN-terminated packets, only egress IRB ACLs can match the inner packets. System filters can be applied only at ingress, not egress.

See the SR Linux Configuration Basics Guide for information about configuring system filter ACLs.

When the SR Linux receives a terminating VXLAN packet on a subinterface, it classifies the packet to one of eight forwarding classes and one of three drop probabilities (low, medium, or high). The classification is based on the following considerations:

• The outer IP header DSCP is not considered.

• If the payload packet is non-IP, the classified FC is fc0 and the classified drop probability is lowest.

• If the payload packet is IP, and there is a classifier policy referenced by the qos classifiers vxlan-default command, that policy is used to determine the FC and drop probability from the header fields of the payload packet.

• If the payload packet is IP, and there is no classifier policy referenced by the qos classifiers vxlan-default command, the default DSCP classifier policy is used to determine the FC and drop probability from the header fields of the payload packet.

When the SR Linux adds VXLAN encapsulation to a packet and forwards it out a subinterface, the inner header IP DSCP value is not modified if the payload packet is IP, even if the egress routed subinterface has a DSCP rewrite rule policy bound to it that matches the packet FC and drop probability. The outer header IP DSCP is set to a static value or copied from the inner header IP DSCP. However, this static or copied value is modified by the DSCP rewrite rule policy that is bound to the egress routed subinterface, if the rule policy exists.

Example:

You can specify a classifier policy that applies to ingress packets received from any remote VXLAN VTEP. The policy applies to payload packets after VXLAN decapsulation has been performed.

The following example specifies a VXLAN classifier policy:

--{ * candidate shared default }--[  ]--
# info qos
    qos {
        classifiers {
            vxlan-default p1 {
                traffic-class 1 {
                    forwarding-class fc0
                }
            }
        }
    }

See the SR Linux Quality of Service Guide for information on configuring QoS.

--{ * candidate shared default }--[  ]--
# info qos
    qos {
        classifiers {
            vxlan-default p1 {
                traffic-class 1 {
                    forwarding-class fc0
                }
            }
        }
    }

--{ candidate shared default }--[  ]--
# info qos rewrite-rules vxlan-outer-header-dscp-policy 
    qos {
        rewrite-rules {
            vxlan-outer-header-dscp-policy vxlan-rewrite-test
            dscp-policy vxlan-rewrite-test 


            }
        }

You can configure SR Linux to collect statistics for VXLAN tunnels. By default, statistics collection for VXLAN tunnels is disabled.

On 7220 IXR-D2/D3 devices, system resources allocated to statistics collection is distributed among Layer 3 or IRB subinterface statistics (if configured), Layer 2 subinterface statistics, and VXLAN statistics.

When Layer 3 or IRB subinterfaces are configured, enabling VXLAN statistics collection reduces the amount of resources available for collecting Layer 2 subinterface statistics:

• If VXLAN statistics collection is disabled (the default), resources are available for collecting statistics for all supported Layer 2 subinterfaces.

• If VXLAN statistics collection is enabled, resources are shared between Layer 2 subinterfaces and VXLAN tunnels, reducing the Layer 2 subinterface scale.

  If the maximum scale is required for Layer 2 subinterfaces, VXLAN statistics collection must be disabled. Disabling VXLAN statistics collection deallocates the resources for VXLAN statistics collection and allocates them to Layer 2 subinterface statistics collection. The VXLAN statistics are not cleared, however; to clear them, use the appropriate tools command. See Clearing VXLAN statistics.

• The amount of resources available for collecting Layer 3 or IRB subinterface statistics does not change if VXLAN statistics collection is enabled or disabled.

--{ candidate shared default }--[  ]--
# info tunnel vxlan-tunnel statistics
    tunnel {
        vxlan-tunnel {
            statistics {
                admin-state enable
            }
        }
    }

--{ running }--[  ]--
# info from state vxlan-tunnel statistics
    vxlan-tunnel {
        statistics {
            in-octets 7296882
            in-packets 83012
            in-discarded-packets 5
            out-octets 7297496
            out-packets 83007
            last-clear 2021-01-29T21:58:40.919Z
        }
    }

--{ running }--[  ]--
# info from state vxlan-tunnel vtep 10.22.22.2
    vxlan-tunnel {
        vtep {
            address 10.22.22.2
            index 677716962894
            last-change 2021-01-29T21:52:34.151Z
            statistics {
                in-octets 7296882
                in-packets 83012
                in-discarded-packets 5
                out-octets 7297496
                out-packets 83007
                last-clear 2021-01-29T21:58:40.919Z
            }
        }
    }

--{ running }--[  ]--
# tools vxlan-tunnel statistics clear

--{ running }--[  ]--
# tools vxlan-tunnel vtep 10.22.22.2 clear