IES configuration

Sample IES configuration

Figure 78-3: Sample IES configuration

Sample configuration steps

The following high-level tasks are necessary to configure this sample IES.


1	Configure policies as required, for example, QoS access ingress and egress interface, Scheduler, ACL IP, Accounting, and ANCP.
2	Create and configure Subscriber 1.
3	Create and configure Service 1.

Workflow to configure an IES

The following workflow lists the high-level steps required to create an IES. As a prerequisite for creating a IES, this workflow assumes the following:

a group or customer with the required user access privileges has been configured.
the IP or IP/MPLS core network exists.
any required service tunnels are created including the static or dynamic LSP required to create the service tunnel; see To create an IP/MPLS service tunnel .
the access ports for the service are created; see Chapter 16, Port and channel object configuration for more information.
any required pre-defined routing, QoS, scheduling, filter, accounting, and time of day suite policies are created; see Chapter 49, Policies overview for more information. You do not have to create pre-defined policies if policies are created on a per-service basis.
any required MP-BGP for PE-to-PE routing is configured; see Chapter 28, Routing protocol configuration for more information about protocol configuration.

Stages


1	Create the IES. See To create an IES . Choose a customer to associate with the IES. Define the general properties for the IES. Turn up the IES service.
2	As required, configure AA reporting. See To configure an IES for AA reporting .
3	As required, create an IES site or GNE IES site. See To configure an IES site and To configure a GNE site on an IES service .
4	As required, perform one or more of the following on an IES site. Apply routing protocols, such as OSPF, RIP, or IS-IS, to an IES site, if required. See To apply OSPF, RIP, or IS-IS to an IES site . Add an IGMP interface to an IES. See To add an IGMP interface to an IES . Add a PIM interface to an IES. See To add a PIM interface to an IES . Create an L2 SDP spoke termination on an IES service. See To create an L2 SDP spoke termination on an IES service . Add a subscriber interface to an IES. See To configure a subscriber interface on an IES . Add an AA interface to an IES. See To add an AA interface to an IES or a VPRN site . Add an AARP interface to an IES. See To add an AARP interface to an IES or a VPRN site . Add a group interface to an IES. See To configure a group interface on an IES . Configure WLAN GW for an IES group interface. See To configure a WLAN GW on an IES group interface . Add a TMS interface to the IES. See To add a TMS interface to an IES . Implement dual homing using SRR. See To implement dual homing using SRRP . Create and enable a video interface for the IES site, if required. See To add a video interface to an IES or VPRN site .
5	As required, create an L3 access interface on an IES site. See To configure an L3 access interface on an IES site .
6	As required, perform one or more of the following on an IES L3 access interface. Configure custom object attributes for AA reporting. See To configure an IES for AA reporting . Bind the L3 access interface to a VPLS site. See To bind an IES L3 access interface to a VPLS site or VPLS I-site . Apply OSPF, RIP, or IS-IS to an IES L3 interface. See To apply OSPF, RIP, or IS-IS to an IES L3 interface . Assign ingress and egress QoS policies. See To assign ingress and egress QoS policies to an IES L3 access interface or To assign ingress and egress QoS policies to an IES L3 access interface on a 7210 SAS site. Configure scheduling. See To configure scheduling on an IES L3 access interface . Assign ingress and egress ACL filters. See To assign ingress and egress ACL filters to an IES L3 access interface . Assign a virtual port to an IES L3 access interface. See To assign a virtual port to an IES L3 access interface. Associate a local DHCPv4 or DCHPv6 server. See To associate a local DHCPv4 or DHCPv6 server to an IES L3 access interface . Assign an accounting policy. See To assign an accounting policy to an IES L3 access interface . Assign an ANCP policy. See To assign an ANCP policy to an IES L3 access interface . Assign a time of day suite. See To assign a time of day suite to an IES L3 access interface . Configure residential subscriber management. See To configure residential subscriber management for an IES L3 access interface . Assign a DoS protection policy or DDoS protection policy. See To assign a DoS protection policy or DDoS protection policy to an IES L3 access interface . Assign an IP address. See To assign an IP address to an IES L3 access interface . Configure BFD. See To configure BFD for an IES L3 access interface . Configure ICMPv4. See To configure ICMPv4 for an IES L3 access interface . Configure ICMPv6. See To configure ICMPv6 on an IES L3 access interface . Assign an ICMP Ping template. See To assign an ICMP ping template to an IES L3 access interface. Configure ARP. See To configure ARP for an IES L3 access interface . Configure neighbor discovery. See To configure neighbor discovery on an IES L3 access interface . Configure DHCPv4. See To configure DHCPv4 for an IES L3 access interface . Create a VRRP instance. See To create a VRRP instance on an IES L3 access interface for a virtual router . Configure anti-spoofing filters. See To configure anti-spoofing filters for an IES L3 access interface . Configure router advertisement. See To configure router advertisement on an IES L3 access interface . Specify queue overrides. See To specify QoS policy overrides on an IES L3 access interface . Configure DHCPv6. See To configure DHCPv6 on an IES L3 access interface . Configure an MLD interface on the L3 access interface. See To configure an MLD interface on an IES L3 access interface .
7	As required, view IES information. View the IES service operational status. See To view the service operational status . View the service topology map associated with an IES. See To view the service topology .
8	As required, modify an IES. Using the Manage Services form. See To modify an IES . Using the topology view. See To modify an IES using the topology view .
9	As required, delete an IES. See To delete an IES .