Procedure 12-6: Suspend OC-12 UPSR to OC-48 UPSR upgrade
Overview
 |
NOTICE Service-disruption hazard |
If a node has been taken out of the Ring Upgrade Mode, the node cannot be returned to the original pre-upgrade state without affecting service.
All nodes connected to the UPSR using the Main slots must be in the provisioned Ring Upgrade Mode.
Important!
This procedure starts at the last node upgraded. The last node upgraded must be connected to the UPSR using the Main slots. Suspending an upgrade at a node connected to the UPSR using port pairs in the Function/Growth slots is not supported.
This procedure assumes that the last node upgraded is a Alcatel-Lucent 1665 DMXtend. However, the Alcatel-Lucent 1665 DMX can also be connected to a UPSR using the Main slots. If the upgrade is suspended at a Alcatel-Lucent 1665 DMX node, refer to the Alcatel-Lucent 1665 Data Multiplexer (DMX) User Operations Guide, 365-372-301, Procedure 12-7: Suspend OC-12 UPSR to OC-48 UPSR upgrade.
Use this procedure to temporarily suspend an OC-12 UPSR to OC-48 UPSR upgrade at a Alcatel-Lucent 1665 DMXtend node connected to the UPSR using single-rate circuit packs.
To temporarily stop the upgrade at a Alcatel-Lucent 1665 DMXtend node connected to the UPSR using multirate circuit packs in the Main/Function/Growth slots, refer to Procedure 12-27: Suspend UPSR/1+1 upgrade at node (multirate circuit packs).
Suspending an upgrade in progress temporarily stops the upgrade.
To return all nodes in the ring to their pre-upgrade state, refer to Procedure 12-5: Back out OC-12 UPSR to OC-48 UPSR upgrade.
When the ring upgrade is temporarily suspended before completion, some spans are operating at the OC-12 line rate and some at the OC-48 line rate. This requires two nodes that are equipped with an OC-12 OLIU circuit pack in one Main slot and an OC-48 OLIU circuit pack in the other Main slot. These nodes are the starting node and the last node upgraded. These nodes must be connected to the UPSR using the Main slots. Suspending an upgrade at a node connected to the UPSR using port pairs in the Function/Growth slots is not supported.
To continue to operate temporarily with different circuit packs in the Main slots, the starting node and the nodes that have been upgraded must remain in the Ring Upgrade Mode.
|
NOTICE Equipment damage |
Rocking circuit packs back and forth when removing or installing them can damage circuit pack and/or shelf connectors.
Do not rock circuit packs back and forth when removing or installing them. Carefully slide circuit packs into or out of the shelf slot.
| |
NOTICE Service-disruption hazard |
Removing or installing circuit packs during a System Reset can cause system errors.
Do not remove or install a circuit pack during a System Reset. If a System Reset occurs, wait until the System Reset is complete, then remove or install the circuit pack.
Before you begin
Prior to performing this procedure:
-
Refer to Laser safety and Electrostatic discharge in Chapter 1, Safety.
-
Review the applicable Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Software Release Description for any detailed procedures or cautions that may apply to this suspend procedure.
Steps
Important!
This procedure starts at the last node upgraded. This procedure assumes that the last node upgraded is a Alcatel-Lucent 1665 DMXtend.
When optical fibers are disconnected during this procedure, inc. LOS, section DCC channel failed, and neighbor SYSCTL CP unavailable alarms are reported. The holdover mode active condition may also be reported depending on the provisioned system timing mode.
Complete the following steps to temporarily suspend an OC-12 to OC-48 UPSR upgrade at a Alcatel-Lucent 1665 DMXtend.
1 |
Identify the last node that was upgraded.
Reference: Procedure 14-2: Connect Personal Computer (PC) and establish WaveStar® CIT session | ||||||
2 |
Important! Both Main slots have been upgraded, and the Configuration → Update System → Upgrade command has been performed. All traffic is now active on Main slot M1, and the system is reporting an inc. OC48 LOS alarm for Main slot M2. Local operating procedures for removing a circuit pack may vary. One method is to disconnect the optical fibers and remove the circuit pack. Another method is to verify the circuit pack active/standby status, perform manual switches if the circuit pack is active, and then disconnect the optical fibers and remove the circuit pack. Determine the local operating procedures for removing a circuit pack before removing the OC-48 OLIU circuit pack in Main slot M2.
| ||||||
3 |
Important! This step is optional. If the OC-48 OLIU circuit pack in Main slot M2 is the active circuit pack for timing and the circuit pack is removed, the system performs an automatic protection switch and subsequent transmission hits (less than 60 ms) will occur. If desired, perform this step to determine the timing state of the OC-48 OLIU circuit pack in Main slot M2. Select View → Timing/Sync. Observe the value of the Active Circuit Pack parameter to determine the active circuit pack for timing. Click Close. | ||||||
4 |
Important! This step is optional. If the OC-48 OLIU circuit pack in Main slot M2 is the active circuit pack for timing, an optional manual timing switch can be performed before replacing the circuit pack in Main slot M2. Transmission hits (less than 60 ms) will occur for each separate protection switch. If the OC-48 OLIU circuit pack in Main slot M1 is the active circuit pack for timing, do not perform this step. To perform an optional manual timing switch, select Fault → Timing/Sync Protection Switch → Main Circuit Pack Timing Switch. Select the Manual Switch Command and click OK. Result: A dialog box appears asking you to confirm executing this command. Click Yes. | ||||||
5 |
If required, repeat Step 3 to verify that the circuit pack in Main slot M1 is now the active circuit pack for timing. | ||||||
6 |
Open the faceplate latch on the OC-48 OLIU circuit pack in Main slot M2. If the circuit pack is active for timing and/or transmission, opening the latch causes timing and/or transmission switches. Disconnect the optical fibers from the OC-48 OLIU circuit pack in Main slot M2. Then replace the OC-48 OLIU circuit pack in Main slot M2 with the original OC-12 OLIU circuit pack. Result: The inc. OC48 LOS alarm for Main slot M2 clears, and system reports an unexpected CP type alarm for Main slot M2. Reference: Procedure 4-2: Install OLIU circuit packs in Main slots | ||||||
7 |
At both ends of the optical span, perform the following to connect the original OC-12 OLIU circuit pack in Main slot M2 and the required OC-12 circuit pack/port at the opposite end of the original OC-12 optical span:
Reference: Procedure 14-4: Perform connection and verification of optical facility | ||||||
8 |
Important! The UPD/INIT button does not work during this upgrade. At the System View select Configuration → Update System → Upgrade. Select main-2 as the Directed Slot Choice and click OK. Result: A dialog box appears asking you to confirm executing this command. Click Yes. The original OC-12 OLIU circuit pack in Main slot M2 is tested and autoprovisioned. The system performs an automatic path protection switch, and all traffic is now active on Main slot M2. Transmission hits (less than 60 ms) occur as traffic switches from the circuit pack in Main slot M1 to the circuit pack in Main slot M2. The unexpected CP type alarm for Main slot M2 clears, and the system reports an unexpected CP type alarm for Main slot M1. | ||||||
9 |
Open the faceplate latch on the OC-48 OLIU circuit pack in Main slot M1. If the circuit pack is active for timing and/or transmission, opening the latch causes timing and/or transmission switches. Disconnect the optical fibers from the OC-48 OLIU circuit pack in Main slot M1. Then replace the OC-48 OLIU circuit pack in Main slot M1 with a temporary replacement OC-48 OLIU circuit pack. Result: The temporary replacement OC-48 OLIU circuit pack in Main slot M1 is tested and autoprovisioned. The unexpected CP type alarm for Main slot M1 clears, and the system reports an unexpected circuit pack type condition for Main slot M1. The system also reports an inc. OC12 LOS alarm for Main slot M1. Reference: Procedure 4-2: Install OLIU circuit packs in Main slots | ||||||
10 |
At both ends of the optical span, perform the following to connect the temporary replacement OC-48 OLIU circuit pack in Main slot M1 and the required OC-48 circuit pack/port at the opposite end of the OC-48 optical span:
Result: The inc. OC12 LOS alarm for Main slot M1 clears, and the system still reports an unexpected circuit pack type condition for Main slot M1. Reference: Procedure 14-4: Perform connection and verification of optical facility STOP! End of Procedure. The upgrade procedure is now temporarily suspended and traffic is supported to the adjacent nodes. To resume the upgrade, replace the temporary replacement OC-48 OLIU circuit pack in Main slot M1 with the upgrade OC-48 OLIU circuit pack, perform a system update, and replace the OC-12 OLIU circuit pack in Main slot M2 with the upgrade OC-48 OLIU circuit pack. Refer to Procedure 12-4: Upgrade OC-12 UPSR to OC-48 UPSR. To back out the upgrade, refer to Procedure 12-5: Back out OC-12 UPSR to OC-48 UPSR upgrade. | ||||||
11 |
Important! Main slot M1 has been upgraded, and the Configuration → Update System → Upgrade command has been performed. All traffic is now active on Main slot M1. Local operating procedures for removing a circuit pack may vary. One method is to disconnect the optical fibers and remove the circuit pack. Another method is to verify the circuit pack active/standby status, perform manual switches if the circuit pack is active, and then disconnect the optical fibers and remove the circuit pack. Determine the local operating procedures for removing a circuit pack before removing the OC-48 OLIU circuit pack in Main slot M1.
| ||||||
12 |
Important! This step is optional. If the OC-48 OLIU circuit pack in Main slot M1 is the active circuit pack for timing and the circuit pack is removed, the system performs an automatic protection switch and subsequent transmission hits (less than 60 ms) will occur. If desired, perform this step to determine the timing state of the OC-48 OLIU circuit pack in Main slot M1. Select View → Timing/Sync. Observe the value of the Active Circuit Pack parameter to determine the active circuit pack for timing. Click Close. | ||||||
13 |
Important! This step is optional. If the OC-48 OLIU circuit pack in Main slot M1 is the active circuit pack for timing, an optional manual timing switch can be performed before replacing the circuit pack in Main slot M1. Transmission hits (less than 60 ms) will occur for each separate protection switch. If the OC-48 OLIU circuit pack in Main slot M2 is the active circuit pack for timing, do not perform this step. To perform an optional manual timing switch, select Fault → Timing/Sync Protection Switch → Main Circuit Pack Timing Switch. Select the Manual Switch Command and click OK. Result: A dialog box appears asking you to confirm executing this command. Click Yes. | ||||||
14 |
If required, repeat Step 12 to verify that the circuit pack in Main slot M2 is now the active circuit pack for timing. | ||||||
15 |
Important! This step is optional. If the OC-48 OLIU circuit pack in Main slot M1 is the active circuit pack for transmission and the circuit pack is removed, the system performs an automatic protection switch and subsequent transmission hits (less than 60 ms) will occur. If desired, perform this step to determine the transmission state of the OC-48 OLIU circuit pack in Main slot M1. Select Reports → Path Protection List and observe the value of the Current Role parameter for the m1-()-() paths supported by the circuit pack in Main slot M1 (Ring 1). Record the active paths supported by the circuit pack in Main slot M1 (Ring 1). Click Close. | ||||||
16 |
Important! This step is optional. If the OC-48 OLIU circuit pack in Main slot M1 is an active circuit pack for transmission, optional manual switches can be performed before replacing the circuit pack in Main slot M1. In UPSRs, each path supported by the circuit pack in Main slot M1 must be switched separately. Transmission hits (less than 60 ms) will occur for each separate protection switch. If the OC-48 OLIU circuit pack in Main slot M1 is not an active circuit pack for transmission, proceed to Step 18. To perform an optional manual transmission switch, select Fault → Protection Switch. Expand Path Protection, click on the required m-1-() path and Select. Select the Manual Switch Type and click Apply. Result: A dialog box appears asking you to confirm executing this command. Click Yes. The system reports a manual switch condition for the affected path. | ||||||
17 |
Repeat Step 16 for each path supported by the circuit pack in Main slot M1. Click Close. | ||||||
18 |
If required, repeat Step 15 to verify that the circuit pack in Main slot M2 is now the active circuit pack for transmission. | ||||||
19 |
Open the faceplate latch on the OC-48 OLIU circuit pack in Main slot M1. If the circuit pack is active for timing and/or transmission, opening the latch causes timing and/or transmission switches. Disconnect the optical fibers from the OC-48 OLIU circuit pack in Main slot M1. Then replace the OC-48 OLIU circuit pack in Main slot M1 with the temporary replacement OC-48 OLIU circuit pack. Result: The system reports an unexpected CP type alarm for Main slot M1. Reference: Procedure 4-2: Install OLIU circuit packs in Main slots | ||||||
20 |
At both ends of the optical span, perform the following to connect the temporary replacement OC-48 OLIU circuit pack in Main slot M1 and the required OC-48 circuit pack/port at the opposite end of the OC-48 optical span:
Reference: Procedure 14-4: Perform connection and verification of optical facility | ||||||
21 |
Important! The UPD/INIT button does not work during this upgrade. At the System View select Configuration → Update System → Upgrade. Select main-1 (default) as the Directed Slot Choice and click OK. Result: A dialog box appears asking you to confirm executing this command. Click Yes. The temporary replacement OC-48 OLIU circuit pack in Main slot M1 is tested and autoprovisioned. The system performs an automatic path protection switch, and all traffic is now active on Main slot M1. Transmission hits (less than 60 ms) occur as traffic switches from the circuit pack in Main slot M2 to the circuit pack in Main slot M1. The unexpected CP type alarm for Main slot M1 clears, and the system reports an unexpected circuit pack type condition for Main slot M2. STOP! End of Procedure. The upgrade procedure is now temporarily suspended and traffic is supported to the adjacent nodes. To resume the upgrade, replace the temporary replacement OC-48 OLIU circuit pack in Main slot M1 with the upgrade OC-48 OLIU circuit pack, perform a system update, and replace the OC-12 OLIU circuit pack in Main slot M2 with the upgrade OC-48 OLIU circuit pack. Refer to Procedure 12-4: Upgrade OC-12 UPSR to OC-48 UPSR. To back out the upgrade, refer to Procedure 12-5: Back out OC-12 UPSR to OC-48 UPSR upgrade. End of steps |
UPSR example
