a Commands
aa-anl-list
aa-anl-list
Syntax
aa-anl-list [congested-only] [sort-type { top-by-subs | top-by-rate} [isa mda-id]
aa-anl-list summary
Context
[Tree] (tools>dump>app-assure>group aa-anl-list)
Full Context
tools dump application-assurance group aa-anl-list
Description
This command displays the list of active ANLs detected by AA along with the associated conditions (for example, congestion, measured rate, and number of subscribers).
Parameters
- congested-only
-
Specifies only congested ANLs.
- sort-type
-
Filters by the specified sub-type.
- mda-id
-
Specifies the slot and MDA in the format slot/mda.
- summary
-
Displays summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of aa-anl-list information.
Output ExampleA:Dut-C# tools dump application-assurance group 120:10 aa-anl-list
============================================================================
Application-Assurance Access Network Location List: Group 120:10, ISA 3/1
============================================================================
Type Location Congestion State Rate (kbps) Subscribers
----------------------------------------------------------------------------
AP-MAC+VLAN 23:89:be:c2:64:50+1034 RTT Limits Exceeded 21961 113
AP-MAC+VLAN 83:2d:3d:73:c4:9a+4090 RTT Limits Exceeded 15963 86
AP-MAC+VLAN f2:ee:cc:47:71:f7+0034 Not Congested 6147 12
============================================================================
aa-interface
aa-interface
Syntax
aa-interface isa mda-id
Context
[Tree] (show>app-assure>group aa-interface)
Full Context
show application-assurance group aa-interface
Description
This command displays AA interface information.
Parameters
- mda-id
-
Specifies the MDA ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
aa-sub
aa-sub
Syntax
aa-sub esm sub-ident-string [snapshot]
aa-sub esm-mac esm-mac-name [snapshot]
aa-sub sap sap-id
aa-sub spoke-id sdp-id:vc-id [ snapshot]
aa-sub transit transit-aasub-name [snapshot]
Context
[Tree] (show>app-assure>group aa-sub)
Full Context
show application-assurance group aa-sub
Description
This command displays per-subscriber statistics.
Parameters
- esm sub-ident-string
-
Specifies an existing subscriber identification string.
- esm-mac esm-mac-name
-
Specifies an existing subscriber MAC.
- sap sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- spoke-id sdp-id:vc-id
-
Specifies the spoke SDP ID and VC ID.
- snapshot
-
Specifies that the statistics retrieved include the sum of the statistics from the previous collection windows, and the statistics for any closed flows since the last collection window.
- transit transit-aasub-name
-
Specifies an existing transit subscriber name string up to 32 characters in length.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the aa-sub command information.
Output Example*A:Dut-C# show application-assurance group 1 aa-sub spoke-sdp 1:1 snapshot application count
===============================================================================
Application-Assurance Subscriber 1:1 (spoke-sdp)
Application Statistics (snapshot)
===============================================================================
Application Disc Octets Packets Flows
-------------------------------------------------------------------------------
Unknown 0% 0 0 0
===============================================================================
*A:Dut-C#
show application-assurance group 1 aa-sub {esm <sub-ident-string> | esm-mac <esm-mac-name> | sap <sap-id> | spoke-sdp <sdp-id:vc-id> } summary
===============================================================================
Application-Assurance Subscriber summary (realtime | snapshot)
===============================================================================
AA-Subscriber : <sub-ident-string> or <sap-id> or <sdp-id:vc-id>
ISA assigned : <Slot/MDA> Unassigned
App-Profile : <app-profile-name>
App-Profile divert : Yes or No
capacity-cost : 100 // for sap/spoke-sdp & esm aa-sub)
Traffic Octets Packets Flows
-------------------------------------------------------------------------------
Admitted from subscriber: 0 0 0
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 0 0 0
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Total flow duration: 0 seconds
Terminated flows: 0
Short Duration flows: 0
Medium Duration flows: 0
Long Duration flows: 0
Top App-Groups Octets Packets Flows
-------------------------------------------------------------------------------
<app-group-name> 100000 3000 30
<app-group-name> 90000 3000 30
<app-group-name> 80000 3000 30
-------------------------------------------------------------------------------
Application Service Options (ASO)
-------------------------------------------------------------------------------
Characteristic Value Derived from
-------------------------------------------------------------------------------
Server Block default
ServiceBw SuperUser app-profile
Teleworker Yes override
VideoBoost Priority override
Total characteristics : 4
Total derived from aso defaults : 1
Total derived from app-profile : 1
Total derived from overrides : 2
-------------------------------------------------------------------------------
A:ALA-IPD# show application-assurance group 1 aa-sub {esm <sub-ident-string>
| esm-mac <esm-mac-name> | sap <sap-id> | spoke-sdp <sdp-id:vc-id> | transit
<transit-aasub-name>} summary
===============================================================================
Application-Assurance Subscriber summary (realtime | snapshot)
==============================================================================
AA-Subscriber : 1:1 (spoke-sdp)
ISA assigned : 3/1
App-Profile : app_prof_D_4
App-Profile divert : Yes
Capacity cost : 1
-------------------------------------------------------------------------------
Traffic Octets Packets Flows
-------------------------------------------------------------------------------
Admitted from subscriber: 0 0 0
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 0 0 0
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Total flow duration: 0 seconds
Terminated flows: 0
Short Duration flows: 0
Medium Duration flows: 0
Long Duration flows: 0
Top App-Groups Octets Packets Flows
-------------------------------------------------------------------------------
<app-group-name> 100000 3000 30
<app-group-name> 90000 3000 30
<app-group-name> 80000 3000 30
===============================================================================
A:ALA-IPD#
A:ALA-IPD# show application-assurance group 1 aa-sub transit <transit-aasub-name>
summary
===============================================================================
Application-Assurance Subscriber summary (realtime | snapshot)
===============================================================================
AA-Subscriber : <transit-aasub-name>
App-Profile : <app-profile-name>
aa-filter : aa-ip <aa-ip-filter-id> or aa-prefix <aa-prefix-filter-id>
Parent : SAP <sap-id> or Spoke-SDP <id> or N/A
Parent ISA assigned : <Slot/MDA> or <None (fail-to-closed | fail-to-open)> or
Unassigned or N/A
Parent app-profile : <app-profile-name> or N/A
Parent divert : Yes or No or N/A
Parent capacity-cost : 2000 or N/A
Traffic Octets Packets Flows
-------------------------------------------------------------------------------
Admitted from subscriber: 0 0 0
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 0 0 0
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Total flow duration: 0 seconds
Terminated flows: 0
Short Duration flows: 0
Medium Duration flows: 0
Long Duration flows: 0
Top App-Groups Octets Packets Flows
-------------------------------------------------------------------------------
<app-group-name> 100000 3000 30
<app-group-name> 90000 3000 30
<app-group-name> 80000 3000 30
===============================================================================
A:ALA-IPD#
show application-assurance group 1 aa-sub {esm <sub-ident-string> | esm-mac <esm-mac-name> |sap <sap-id> | spoke-sdp <sdp-id:vc-id> | transit <transit-aasub-name>} count
A:ALA-IPD# show application-assurance group 1 aa-sub {esm <sub-ident-string> | esm-mac <esm-mac-name> | sap <sap-id> | spoke-sdp <sdp-id:vc-id> | transit <transit-aasub-name>} snapshot
count
===============================================================================
Application-Assurance Subscriber esm|sap|spoke-sdp|transit <name>
Application Group, Application and Protocol Statistics (realtime | snapshot)
===============================================================================
Application Group Disc Octets Packets Flows
-------------------------------------------------------------------------------
Games 0% 0 0 0
Mail 0% 0 0 0
Peer to Peer 0% 0 0 0
Unknown 0% 0 0 0
Web 0% 0 0 0
===============================================================================
Application Disc Octets Packets Flows
-------------------------------------------------------------------------------
SIP 0% 0 0 0
-------------------------------------------------------------------------------
Protocol statistics are not configured in statistics>aa-sub
===============================================================================
A:ALA-IPD#
A:ALA-IPD# show application-assurance group 1 aa-sub {esm <sub-ident-string> | esm-mac <esm-mac-name> | sap <sap-id> | spoke-sdp <sdp-id:vc-id> | transit <transit-aasub-name>}
application count detail
===============================================================================
Application-Assurance Subscriber esm|esm-mac|sap|spoke-sdp|transit <name>
Application Statistics (realtime | snapshot)
===============================================================================
Subscriber Application:
Type Octets Packets Flows
-------------------------------------------------------------------------------
name SIP:
Admitted from subscriber: 0 0 0
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 0 0 0
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Max per min from sub: 1000 10
Max per min to sub: 2000 20
Total flow duration: 0 seconds
Terminated flows: 0
Short Duration flows: 0
Medium Duration flows: 0
Long Duration flows: 0
===============================================================================
A:ALA-IPD#
aa-sub
Syntax
aa-sub dsm mac mac-address [snapshot]
aa-sub esm sub-ident-string
aa-sub esm-mac esm-mac-name
aa-sub transit transit-aasub-name
Context
[Tree] (tools>dump>app-assure>group aa-sub)
Full Context
tools dump application-assurance group aa-sub
Description
This command displays AA subscriber information for a specific ISA.
Parameters
- esm-mac-name
-
Specifies the ESM MAC name; a maximum of 32 characters.
- mac-address
-
Specifies the MAC address in xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx format.
- snapshot
-
Displays snapshot statistics.
- sub-ident-string
-
Specifies the AA subscriber identifier string, up to 32 characters.
- transit-aasub-name
-
Specifies the AA transit subscriber name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of AA subscriber information.
Output ExampleA:Dut-C# tools dump application-assurance group 120:10 aa-sub dsm mac 00:01:02:00:00:00 summary
============================================================================
Application-Assurance Subscriber Summary (realtime)
============================================================================
MAC : 00:01:02:00:00:00 (dsm)
ISA assigned : 3/1
Group : 120:10
App-Profile : AppPro1
HTTP URL Parameters : (Not Specified)
Access Network Location : 04:7d:be:fb:64:a8+0243 (Not Congested)
ANL Type : AP-MAC+VLAN
Last HTTP Notified Time : N/A
----------------------------------------------------------------------------
Traffic Octets Packets Flows
----------------------------------------------------------------------------
From subscriber:
Admitted 0 0 0
Denied 0 0 0
Active flows 0
To subscriber:
Admitted 0 0 0
Denied 0 0 0
Active flows 0
Flow counts:
Short duration 0
Med duration 0
Long duration 0
Total flow duration : 0 seconds
----------------------------------------------------------------------------
Application Service Options (ASO)
----------------------------------------------------------------------------
Characteristic Value Derived from
----------------------------------------------------------------------------
Char1 val10 default
============================================================================
aa-sub
Syntax
aa-sub esm sub-ident-string
aa-sub esm-mac esm-mac-name
aa-sub sap sap-id
aa-sub spoke-id sdp-id:vc-id
aa-sub transit transit-aasub-name
Context
[Tree] (tools>perform>app-assure>group aa-sub)
Full Context
tools perform application-assurance group aa-sub
Description
This command performs application assurance group aa-sub operations.
Parameters
- esm sub-ident-string
-
Specifies an existing subscriber identification string.
- esm-mac esm-mac-name
-
Specifies an existing subscriber MAC.
- sap sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- spoke-id sdp-id:vc-id
-
Specifies the spoke SDP ID and VC ID.
- transit transit-aasub-name
-
Specifies an existing transit subscriber name string up to 32 characters in length.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
aa-sub-list
aa-sub-list
Syntax
aa-sub-list [isa mda-id]
aa-sub-list policers-exceeded
aa-sub-list summary
Context
[Tree] (show>app-assure>group aa-sub-list)
Full Context
show application-assurance group aa-sub-list
Description
This command displays AA subscriber lists.
Parameters
- isa mda-id
-
Displays the slot and MDA ID.
- policers-exceeded
-
Displays the policer resources which are exceeded.
- summary
-
Displays summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the aa-sub-list command information.
Output Example*A:Dut-C# show application-assurance group 74:40346 aa-sub-list summary
=============================================================================
Application-Assurance Subscriber Summary for Group 74:40346
=============================================================================
all esm sap spoke-sdp transit esm-mac
-----------------------------------------------------------------------------
Total 100 0 0 0 0 100
Overrides 100 0 0 0 0 100
-----------------------------------------------------------------------------
Total number of aa-subs found : 100
Total number of aa-subs with overrides found : 100
=============================================================================
*A:Dut-C# show application-assurance group 224:10559 aa-sub-list
============================================================================
Application-Assurance Subscriber List for Group 224:10559
============================================================================
type aa-sub ISA App-Profile divert
assigned
----------------------------------------------------------------------------
sap 1/1/1:113 3/2 prof_224_10559_1 Yes
sap 1/1/1:241 3/2 prof_224_10559_1 Yes
sap 1/1/1:369 3/2 prof_224_10559_1 Yes
sap 1/1/1:497 3/2 prof_224_10559_1 Yes
sap 1/1/4:113 3/2 prof_224_10559_2 Yes
sap 1/1/4:241 3/2 prof_224_10559_2 Yes
sap 1/1/4:369 3/2 prof_224_10559_2 Yes
sap 1/1/4:497 3/2 prof_224_10559_2 Yes
----------------------------------------------------------------------------
Total number of aa-subs found : 8
============================================================================
*A:Dut-C#
*A:Dut-C# show application-assurance group 224:10559 aa-sub-list isa 3/2
============================================================================
Application-Assurance Subscriber List for Group 224:10559, isa 3/2
============================================================================
type aa-sub ISA App-Profile divert
assigned
----------------------------------------------------------------------------
sap 1/1/1:113 3/2 prof_224_10559_1 Yes
sap 1/1/1:241 3/2 prof_224_10559_1 Yes
sap 1/1/1:369 3/2 prof_224_10559_1 Yes
sap 1/1/1:497 3/2 prof_224_10559_1 Yes
sap 1/1/4:113 3/2 prof_224_10559_2 Yes
sap 1/1/4:241 3/2 prof_224_10559_2 Yes
sap 1/1/4:369 3/2 prof_224_10559_2 Yes
sap 1/1/4:497 3/2 prof_224_10559_2 Yes
----------------------------------------------------------------------------
Total number of aa-subs found : 8
============================================================================
*A:Dut-C#
A:ALA-IPD# show application-assurance group 2 aa-sub-list [isa <mda-id>]
===========================================================================
Application-Assurance Subscriber List for Group 2, isa <slot/mda>
===========================================================================
type aa-sub ISA App-Profile divert
assigned
---------------------------------------------------------------------------
group 2:50
---------------------------------------------------------------------------
esm Bob 3/1 Grp2P50appProf1 Yes
esm Fred 1/1 Grp2P50appProf2 Yes
sap 1/2/9 3/1 Grp2P50appProf1 Yes
sap 1/2/10 1/1 Grp2P50appProf2 Yes
spoke-sdp 1:7 1/1 Grp2P50appProf1 Yes
spoke-sdp 2:101 3/1 Grp2P50appProf2 Yes
esm-mac Sub3-000102030405 1/1 Grp2P50appProf2 Yes
---------------------------------------------------------------------------
group 2:32656
---------------------------------------------------------------------------
esm Alex 1/1 appProf1 Yes
esm Sub1 3/1 Lite Yes
esm Max 3/1 appProf1 Yes
esm tcpr_sub 1/1 appProf2 Yes
sap 1/2/5 3/1 appProf1 Yes
sap 1/2/6 1/1 appProf1 Yes
sap 2/2/4:111 1/1 Power Yes
spoke-sdp 1:6 1/1 appProf1 Yes
spoke-sdp 2:100 3/1 appProf2 Yes
esm-mac Sub4-000203040506 3/1 appProf2 Yes
---------------------------------------------------------------------------
Number of aa-subs found in group 2:50 : 6
Number of aa-subs found in group 2:32656 : 9
Total number of aa-subs found : 15
===========================================================================
A:ALA-IPD#
A:ALA-IPD# show application-assurance group 2:32656 aa-sub-list [isa <mda-id>
=========================================================================
Application-Assurance Subscriber List for Group 2:32656, isa <slot/mda>
=========================================================================
type aa-sub ISA App-Profile divert
assigned
-------------------------------------------------------------------------
esm Alex 1/1 appProf1 Yes
esm Sub1 3/1 Lite Yes
esm Max 3/1 appProf1 Yes
esm tcpr_sub 1/1 appProf2 Yes
sap 1/2/5 3/1 appProf1 Yes
sap 1/2/6 1/1 appProf1 Yes
sap 2/2/4:111 1/1 Power Yes
spoke-sdp 2:100 1/1 appProf8 Yes
esm-mac diameter_esm-000100000001 3/2 appProf2 Yes
esm-mac diameter_esm-000100000002 3/2 appProf2 Yes
-------------------------------------------------------------------------
Number of aa-subs : 8
=========================================================================
A:ALA-IPD#
*A:Dut-C# show application-assurance group 74 aa-sub-list isa 3/2
==============================================================================
Application-Assurance Subscriber List for Group 74, isa 3/2
==============================================================================
type aa-sub ISA App-Profile divert
assigned
------------------------------------------------------------------------------
group 74:40346
------------------------------------------------------------------------------
esm-mac diameter_esm-000100000001 3/2 appProf2 Yes
esm-mac diameter_esm-000100000002 3/2 appProf2 Yes
aa-sub-list
Syntax
aa-sub-list [filter-by-type sub-type] [ isa mda-id] quarantined-only
aa-sub-list [filter-by-type sub-type] [ isa mda-id] policers-exceeded
aa-sub-list summary
Context
[Tree] (tools>dump>app-assure>group aa-sub-list)
Full Context
tools dump application-assurance group aa-sub-list
Description
This command displays the AA subscriber list for a specific ISA.
Parameters
- filter-by-type sub-type
-
Filters by the specified sub-type.
- mda-id
-
Specifies the slot and MDA in the format slot/mda.
- summary
-
Displays summary information.
- quarantined-only
-
Displays the AA subscribers that are under quarantine.
- policers-exceeded
-
Displays subscribers that have exceeded policer resources.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of AA subscriber list information.
Output Example*A:Dut-C# tools dump application-assurance group 1 aa-sub-list quarantined-only
===============================================================================
Application-Assurance Sub List (quarantined): Group 1, ISA 3/1
===============================================================================
Type AA-Sub App Profile Part
Id
(Quarantined Since) (Last Quarantine Event)
-------------------------------------------------------------------------------
esm Sub1 app-profile-1 0
(01/30/2018 14:25:22) (01/30/2018 15:27:3)
spoke-Sdp 1000:150 app-profile-2 0
(01/30/2018 13:25:22) (01/30/2018 16:27:3)
esm-mac Sub3-000102030405 app-profile-1 0
(01/30/2018 12:25:22) (01/30/2018 17:27:3)
transit t1 app-profile-4 0
(01/30/2018 11:25:22) (01/30/2018 18:27:3)
-------------------------------------------------------------------------------
Number of AA Subscribers : 4
*A:Dut-C# tools dump application-assurance group 1 aa-sub-list summary
==========================================================================
Application-Assurance Subscriber Summary for Group 1, ISA 5/2
==========================================================================
all esm sap spoke- transit dsm esm-mac
sdp
--------------------------------------------------------------------------
Total 0 0 0 0 0 0 0
Overrides 0 0 0 0 0 0 0
Pol Exceeded 0 0 0 0 0 0 0
Congested 0 0 0 0 0 0 0
Quarantined 0 0 0 0 0 0 0
--------------------------------------------------------------------------
Total number of aa-subs found : 0
Total number of aa-subs with overrides found : 0
Total number of aa-subs with policer resources exceeded found : 0
Total number of congested aa-subs found : 0
Total number of quarantined aa-subs found : 0
==========================================================================
aa-sub-search
aa-sub-search
Syntax
aa-sub-search search-type granularity [direction direction] [max-count max-count]
Context
[Tree] (tools>dump>app-assure>group aa-sub-search)
Full Context
tools dump application-assurance group aa-sub-search
Description
This command displays AA aa-sub information.
Parameters
- search-type
-
Specifies the type of search.
- granularity
-
Specifies the granularity of the search.
- direction direction
-
Specifies the network/subscriber direction.
- max-count max-count
-
Specifies the maximum flows to display.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of AA aa-sub information.
Output ExampleA:Dut-C# tools dump application-assurance group 74 aa-sub-search top bytes
===============================================================================
Application-Assurance aa-sub search for Group 74: Top 10 by bytes (both)
===============================================================================
Entry isa SubType SubName
From-sub-count To-sub-count Group:Partition Interval(UTC)
1 3/2 esm-mac "diameter_esm-000100000001"
40 42 74:40346 "01/13/2017 14:39:18"
2 3/2 esm-mac "diameter_esm-000100000002"
40 42 74:40346 "01/13/2017 14:39:18"
3 3/2 esm-mac "diameter_esm-000100000003"
40 42 74:40346 "01/13/2017 14:39:18"
4 3/2 esm-mac "diameter_esm-000100000004"
40 42 74:40346 "01/13/2017 14:39:18"
5 3/2 esm-mac "diameter_esm-000100000005"
40 42 74:40346 "01/13/2017 14:39:18"
6 3/2 esm-mac "diameter_esm-000100000006"
40 42 74:40346 "01/13/2017 14:39:18"
7 3/2 esm-mac "diameter_esm-000100000007"
40 42 74:40346 "01/13/2017 14:39:18"
8 3/2 esm-mac "diameter_esm-000100000008"
40 42 74:40346 "01/13/2017 14:39:18"
9 3/2 esm-mac "diameter_esm-000100000009"
40 42 74:40346 "01/13/2017 14:39:18"
10 3/2 esm-mac "diameter_esm-00010000000a"
40 42 74:40346 "01/13/2017 14:39:18"
Total number of aa-subs found: 10
aa-sub-study
aa-sub-study
Syntax
aa-sub-study esm sub-ident-string [snapshot]
aa-sub-study esm-mac esm-mac-name [snapshot]
aa-sub-study sap sap-id [snapshot]
aa-sub-study spoke-sdp sdp-id:vc-id [snapshot]
aa-sub-study transit transit-aasub-name [ snapshot]
Context
[Tree] (show>app-assure>group aa-sub-study)
Full Context
show application-assurance group aa-sub-study
Description
This command displays per-subscriber special study statistics.
Parameters
- esm sub-ident-string
-
Specifies an existing subscriber identification string.
- esm-mac esm-mac-name
-
Specifies an existing subscriber MAC.
- sap sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- spoke-id sdp-id:vc-id
-
Specifies the spoke SDP ID and VC ID.
- snapshot
-
Specifies that the statistics retrieved include the sum of the statistics from the previous collection windows, and the statistics for any closed flows since the last collection window.
- transit transit-aasub-name
-
Specifies an existing transit subscriber name string.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
aa-sub-using
aa-sub-using
Syntax
aa-sub-using
aa-sub-using app-profile app-profile-name
Context
[Tree] (show>service aa-sub-using)
Full Context
show service aa-sub-using
Description
This command displays the subscribers and associated services diverted to Application Assurance using a specific app profile name.
Parameters
- app-profile-name
-
Specifies the application profile name.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the aa-sub-using command information.
Output Example*A:Dut-C# show service aa-sub-using
===============================================================================
Aa-Subscribers
===============================================================================
aa-sub-type aa-sub-name app-profile-name
-------------------------------------------------------------------------------
esm-mac diameter_esm-000100000001 app-prof~%;&+-!?
esm-mac diameter_esm-000100000002 app-prof~%;&+-!?
....
esm-mac diameter_esm-000100000064 app-prof~%;&+-!?
-------------------------------------------------------------------------------
Number of ESM subs : 0
Number of ESM mac subs : 100
Number of SAP subs : 0
Number of Spoke-Sdp subs : 0
Number of Transit subs : 0
Total number of aa-subs : 100
-------------------------------------------------------------------------------
aaa
aaa
Syntax
aaa
Context
[Tree] (clear aaa)
Full Context
clear aaa
Description
Commands in this context clear authentication, authorization, and accounting data.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
aaa
Syntax
aaa
Context
[Tree] (show aaa)
Full Context
show aaa
Description
Commands in this context display authentication, authorization, and accounting data.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
aaa
Syntax
aaa
Context
[Tree] (tools>dump aaa)
Full Context
tools dump aaa
Description
Commands in this context dump authentication, authorization, and accounting information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
aaa
Syntax
aaa
Context
[Tree] (tools>perform aaa)
Full Context
tools perform aaa
Description
Commands in this context perform AAA operations.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
aarp
aarp
Syntax
aarp
aarp aarpId
Context
[Tree] (show>app-assur aarp)
Full Context
show application-assurance aarp
Description
This command displays the Application Assurance Redundancy Protocol (AARP) instance status.
Parameters
- aarpId
-
Specifies an integer that identifies an AARP instance.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
aarp
Syntax
aarp aarpId event-history [clear]
Context
[Tree] (tools>dump>application-assurance aarp)
Full Context
tools dump application-assurance aarp
Description
This command dumps application-assurance AARP information for a specified instance.
Parameters
- aarpId
-
Specifies the AARP ID.
- event-history
-
Dumps historical information for the instance.
- clear
-
Clears the event history after reading.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
aarp
Syntax
aarp aarpId force-evaluate
Context
[Tree] (tools>perform>app-assure aarp)
Full Context
tools perform application-assurance aarp
Description
This command performs Application Assurance Redundancy Protocol instance operations.
Parameters
- aarpId
-
Specifies an integer that identifies an AARP instance.
- force-evaluate
-
Forces a re-evaluation of the preferred AARP instance.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
abort-startup-wait
abort-startup-wait
Syntax
abort-startup-wait
Context
[Tree] (tools>perform>router>dhcp>server>failover abort-startup-wait)
[Tree] (tools>perform>router>dhcp6>server>pool>failover abort-startup-wait)
[Tree] (tools>perform>router>dhcp6>server>failover abort-startup-wait)
[Tree] (tools>perform>router>dhcp>server>pool>failover abort-startup-wait)
Full Context
tools perform router dhcp local-dhcp-server failover abort-startup-wait
tools perform router dhcp6 local-dhcp-server pool failover abort-startup-wait
tools perform router dhcp6 local-dhcp-server failover abort-startup-wait
tools perform router dhcp local-dhcp-server pool failover abort-startup-wait
Description
This command aborts the running start-up-wait time, forcing the DCHP server to transition immediately to the COMMUNICATIONS-INTERRUPTED state.
The start-up-wait time is started after a boot to enable two redundant routers to synchronize the DHCP server lease database before transitioning to the (PRE-)NORMAL state when the last state record from the peer is synchronized. If the last state record is not received before the start-up-wait time expires, it is assumed that the remote DHCP server is not operational and the DHCP server goes in COMMUNICATIONS-INTERRUPTED state.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
access-group
access-group
Syntax
access-group [group-name]
Context
[Tree] (show>system>security access-group)
Full Context
show system security access-group
Description
This command displays SNMP access group information.
Parameters
- group-name
-
This command displays information for the specified access group.
Platforms
All
Output
The following output is an example of access group information.
Show System Security Access Group Output Fields describes security access group output fields.
Output ExampleA:ALA-4# show system security access-group
===============================================================================
Access Groups
===============================================================================
group name security security read write notify
model level view view view
-------------------------------------------------------------------------------
snmp-ro snmpv1 none no-security no-security
snmp-ro snmpv2c none no-security no-security
snmp-rw snmpv1 none no-security no-security no-security
snmp-rw snmpv2c none no-security no-security no-security
snmp-rwa snmpv1 none iso iso iso
snmp-rwa snmpv2c none iso iso iso
snmp-trap snmpv1 none iso
snmp-trap snmpv2c none iso
===============================================================================
A:ALA-7#
Label |
Description |
---|---|
Group name |
The access group name. |
Security model |
The security model required to access the views configured in this node. |
Security level |
Specifies the required authentication and privacy levels to access the views configured in this node. |
Read view |
Specifies the variable of the view to read the MIB objects. |
Write view |
Specifies the variable of the view to configure the contents of the agent. |
Notify view |
Specifies the variable of the view to send a trap about MIB objects. |
access-group
Syntax
access-group group-name
Context
[Tree] (show>system>security access-group)
Full Context
show system security access-group
Description
This command displays access-group information.
Platforms
All
Output
The following output is an example of access group information.
Show System Security Access-Group Output Fields describes the access-group output fields.
Output ExampleA:ALA-1# show system security access-group
===============================================================================
Access Groups
===============================================================================
group name security security read write notify
model level view view view
-------------------------------------------------------------------------------
snmp-ro snmpv1 none no-security no-security
snmp-ro snmpv2c none no-security no-security
snmp-rw snmpv1 none no-security no-security no-security
snmp-rw snmpv2c none no-security no-security no-security
snmp-rwa snmpv1 none iso iso iso
snmp-rwa snmpv2c none iso iso iso
snmp-trap snmpv1 none iso
snmp-trap snmpv2c none iso
-------------------------------------------------------------------------------
No. of Access Groups: 8
===============================================================================
A:ALA-1#
A:ALA-1# show system security access-group detail
===============================================================================
Access Groups
===============================================================================
group name security security read write notify
model level view view view
-------------------------------------------------------------------------------
snmp-ro snmpv1 none no-security no-security
-------------------------------------------------------------------------------
No. of Access Groups:
...
===============================================================================
A:ALA-1#
Label |
Description |
---|---|
Group name |
The access group name. |
Security model |
The security model required to access the views configured in this node. |
Security level |
Specifies the required authentication and privacy levels to access the views configured in this node. |
Read view |
Specifies the view to read the MIB objects. |
Write view |
Specifies the view to configure the contents of the agent. |
Notify view |
Specifies the view to send a trap about MIB objects. |
No. of access groups |
The total number of configured access groups. |
accounting-policy
accounting-policy
Syntax
accounting-policy [acct-policy-id] [access | network] [associations]
Context
[Tree] (show>log accounting-policy)
Full Context
show log accounting-policy
Description
This command displays accounting policy information.
Parameters
- policy-id
-
Specifies the policy ID that uniquely identifies the accounting policy, expressed as a decimal integer.
- access
-
Specifies to only display access accounting policies.
- network
-
Specifies to only display network accounting policies.
- association
-
Displays accounting-policy associations.
Platforms
All
Output
The following output is an example of accounting policy information.
Show Accounting Policy Output Fields describes accounting policy output fields.
Output ExampleA:ALA-1# show log accounting-policy
==============================================================================
Accounting Policies
==============================================================================
Policy Type Def Admin Oper Intvl File Record Name
Id State State Id
------------------------------------------------------------------------------
1 network No Up Up 15 1 network-ingress-packets
2 network Yes Up Up 15 2 network-ingress-octets
10 access Yes Up Up 5 3 complete-service-ingress-egress
==============================================================================
A:ALA-1#
A:ALA-1# show log accounting-policy 10
==============================================================================
Accounting Policies
==============================================================================
Policy Type Def Admin Oper Intvl File Record Name
Id State State Id
------------------------------------------------------------------------------
10 access Yes Up Up 5 3 complete-service-ingress-egress
Description : (Not Specified)
This policy is applied to:
Svc Id: 100 SAP : 1/1/8:0 Collect-Stats
Svc Id: 101 SAP : 1/1/8:1 Collect-Stats
Svc Id: 102 SAP : 1/1/8:2 Collect-Stats
Svc Id: 103 SAP : 1/1/8:3 Collect-Stats
Svc Id: 104 SAP : 1/1/8:4 Collect-Stats
Svc Id: 105 SAP : 1/1/8:5 Collect-Stats
Svc Id: 106 SAP : 1/1/8:6 Collect-Stats
Svc Id: 107 SAP : 1/1/8:7 Collect-Stats
Svc Id: 108 SAP : 1/1/8:8 Collect-Stats
Svc Id: 109 SAP : 1/1/8:9 Collect-Stats
...
==============================================================================
A:ALA-1#
A:ALA-1# show log accounting-policy network
==============================================================================
Accounting Policies
==============================================================================
Policy Type Def Admin Oper Intvl File Record Name
Id State State Id
------------------------------------------------------------------------------
1 network No Up Up 15 1 network-ingress-packets
2 network Yes Up Up 15 2 network-ingress-octets
==============================================================================
A:ALA-1#
A:ALA-1# show log accounting-policy access
==============================================================================
Accounting Policies
==============================================================================
Policy Type Def Admin Oper Intvl File Record Name
Id State State Id
------------------------------------------------------------------------------
10 access Yes Up Up 5 3 complete-service-ingress
==============================================================================
A:ALA-1#
Label |
Description |
---|---|
Policy ID |
The identifying value assigned to a specific policy. |
Type |
Identifies accounting record type forwarded to the configured accounting file. access — Indicates that the policy is an access accounting policy. network — Indicates that the policy is a network accounting policy. none — Indicates no accounting record types assigned. |
Def |
Yes — Indicates that the policy is a default access or network policy. No — Indicates that the policy is not a default access or network policy. |
Admin State |
Displays the administrative state of the policy. Up — Indicates that the policy is administratively enabled. Down — Indicates that the policy is administratively disabled. |
Oper State |
Displays the operational state of the policy. Up — Indicates that the policy is operationally up. Down — Indicates that the policy is operationally down. |
Intvl |
Displays the interval, in minutes, in which statistics are collected and written to their destination. The default depends on the record name type. |
File ID |
The log destination. |
Record Name |
The accounting record name which represents the configured record type. |
This policy is applied to |
Specifies the entity where the accounting policy is applied. |
accounting-records
accounting-records
Syntax
accounting-records
Context
[Tree] (show>log accounting-records)
Full Context
show log accounting-records
Description
This command displays accounting policy record names.
Platforms
All
Output
The following output is an example of accounting records output information.
Accounting Policy Output Fields describes accounting records output fields.
Label |
Description |
---|---|
Record # |
The record ID that uniquely identifies the accounting policy, expressed as a decimal integer. |
Record Name |
The accounting record name. |
Def. Interval |
The default interval, in minutes, in which statistics are collected and written to their destination. |
aa, video and subscriber records are not applicable to the 7950 XRS.
# show log accounting-records
===========================================================
Accounting Policy Records
===========================================================
Record # Record Name Def. Interval
-----------------------------------------------------------
1 service-ingress-octets 5
2 service-egress-octets 5
3 service-ingress-packets 5
4 service-egress-packets 5
5 network-ingress-octets 15
6 network-egress-octets 15
7 network-ingress-packets 15
8 network-egress-packets 15
9 compact-service-ingress-octets 5
10 combined-service-ingress 5
11 combined-network-ing-egr-octets 15
12 combined-service-ing-egr-octets 5
13 complete-service-ingress-egress 5
14 combined-sdp-ingress-egress 5
15 complete-sdp-ingress-egress 5
16 complete-subscriber-ingress-egress 5
17 aa-protocol 15
18 aa-application 15
19 aa-app-group 15
20 aa-subscriber-protocol 15
21 aa-subscriber-application 15
23 custom-record-subscriber 5
24 custom-record-service 5
25 custom-record-aa-sub 15
26 queue-group-octets 15
27 queue-group-packets 15
28 combined-queue-group 15
29 combined-mpls-lsp-ingress 5
30 combined-mpls-lsp-egress 5
31 combined-ldp-lsp-egress 5
32 saa 5
33 video 10
34 kpi-system 5
35 kpi-bearer-mgmt 5
36 kpi-bearer-traffic 5
37 kpi-ref-point 5
38 kpi-path-mgmt 5
39 kci-iom-3 5
40 kci-system 5
41 kci-bearer-mgmt 5
42 kci-path-mgmt 5
43 complete-kpi 5
44 complete-kci 5
45 kpi-bearer-group 5
46 kpi-ref-path-group 5
47 kpi-kci-bearer-mgmt 5
48 kpi-kci-path-mgmt 5
49 kpi-kci-system 5
50 complete-kpi-kci 5
51 aa-performance 15
52 complete-ethernet-port 15
53 extended-service-ingress-egress 5
54 complete-network-ing-egr 15
55 aa-partition 15
56 complete-pm 5
63 aa-admit-deny 15
0 nat-binding-port-block 0
65 network-interface-ingress-octets 15
66 network-interface-egress-octets 15
67 network-interface-ingress-packets 15
68 network-interface-egress-packets 15
69 combined-network-interface-ingress 15
70 combined-network-interface-egress 15
71 complete-network-interface-ing-egr 15
72 access-egress-octets 15
73 access-egress-packets 15
74 combined-access-egress 15
75 combined-network-egress 15
76 complete-service-activation-test 5
77 combined-mpls-srte-egress 5
===========================================================
Default Collection Interval for Accounting Records lists the accounting record names available and the default collection interval.
Record Type |
Accounting Record Name |
Default Interval |
---|---|---|
1 |
service-ingress-octets |
5 |
2 |
service-egress-octets |
5 |
3 |
service-ingress-packets |
5 |
4 |
service-egress-packets |
5 |
5 |
network-ingress-octets |
15 |
6 |
network-egress-octets |
15 |
7 |
network-ingress-packets |
15 |
8 |
network-egress-packets |
15 |
9 |
compact-service-ingress-octets |
5 |
10 |
combined-service-ingress |
5 |
11 |
combined-network-ing-egr-octets |
15 |
12 |
combined-service-ing-egr-octets |
5 |
13 |
complete-service-ingress-egress |
5 |
14 |
combined-sdp-ingress-egress |
5 |
15 |
complete-sdp-ingress-egress |
5 |
16 |
complete-subscriber-ingress-egress |
5 |
17 |
aa-protocol |
15 |
18 |
aa-application |
15 |
19 |
aa-app-group |
15 |
20 |
aa-subscriber-protocol |
15 |
21 |
aa-subscriber-application |
15 |
23 |
custom-record-subscriber |
5 |
24 |
custom-record-service |
5 |
25 |
custom-record-aa-sub |
15 |
26 |
queue-group-octets |
15 |
27 |
queue-group-packets |
15 |
28 |
combined-queue-group |
15 |
29 |
combined-mpls-lsp-ingress |
5 |
30 |
combined-mpls-lsp-egress |
5 |
31 |
combined-ldp-lsp-egress |
5 |
32 |
saa |
5 |
33 |
video |
10 |
34 |
kpi-system |
5 |
35 |
kpi-bearer-mgmt |
5 |
36 |
kpi-bearer-traffic |
5 |
37 |
kpi-ref-point |
5 |
38 |
kpi-path-mgmt |
5 |
39 |
kci-iom-3 |
5 |
40 |
kci-system |
5 |
41 |
kci-bearer-mgmt |
5 |
42 |
kci-path-mgmt |
5 |
43 |
complete-kpi |
5 |
44 |
complete-kci |
5 |
45 |
kpi-bearer-group |
5 |
46 |
kpi-ref-path-group |
5 |
47 |
kpi-kci-bearer-mgmt |
5 |
48 |
kpi-kci-path-mgmt |
5 |
49 |
kpi-kci-system |
5 |
50 |
complete-kpi-kci |
5 |
51 |
aa-performance |
15 |
52 |
complete-ethernet-port |
15 |
53 |
extended-service-ingress-egress |
5 |
54 |
complete-network-ing-egr |
15 |
55 |
aa-partition |
15 |
56 |
complete-pm |
5 |
63 |
aa-admit-deny |
15 |
0 |
nat-binding-port-block |
0 |
65 |
network-interface-ingress-octets |
15 |
66 |
network-interface-egress-octets |
15 |
67 |
network-interface-ingress-packets |
15 |
68 |
network-interface-egress-packets |
15 |
69 |
combined-network-interface-ingress |
15 |
70 |
combined-network-interface-egress |
15 |
71 |
complete-network-interface-ing-egr |
15 |
72 |
access-egress-octets |
15 |
73 |
access-egress-packets |
15 |
74 |
combined-access-egress |
15 |
75 |
combined-network-egress |
15 |
76 |
complete-service-activation-test |
5 |
77 |
combined-mpls-srte-egress |
5 |
acct-off
acct-off
Syntax
acct-off [radius-server-policy policy-name] [ force] [acct-terminate-cause number]
Context
[Tree] (tools>perform>aaa acct-off)
Full Context
tools perform aaa acct-off
Description
This command triggers a RADIUS Accounting-Off message:
-
for all radius-server-policies that have acct-on-off configured
-
for the specified radius-server-policy if the acct-on-off is configured
The Accounting-Off message is not sent when the last successful event for the radius server policy was an Accounting-Off message. In this case, an Accounting-On should be sent first. By specifying the keyword force, this is overruled.
Parameters
- policy-name
-
Specifies the radius-server-policy for which the Accounting-Off should be sent.
- force
-
Sends an Accounting-On also if the last successful event was an Accounting-Off.
- number
-
Overrides the default Acct-Terminate-Cause (User-Request) in the Accounting-Off message.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
acct-on
acct-on
Syntax
acct-on [radius-server-policy policy-name] [ force]
Context
[Tree] (tools>perform>aaa acct-on)
Full Context
tools perform aaa acct-on
Description
This command triggers a RADIUS Accounting-On message:
-
for all radius-server-policies that have acct-on-off configured.
-
for the specified radius-server-policy if the acct-on-off is configured
The Accounting-On message is not sent when the last successful event for the RADIUS server policy was an Accounting-On message. In this case, an Accounting-Off should be sent first. By specifying the keyword force, this is overruled.
Parameters
- policy-name
-
Specifies the radius-server-policy for which the Accounting-On should be sent.
- force
-
Sends an Accounting-On also if the last successful event was an Accounting-On.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
acct-on-off-group
acct-on-off-group
Syntax
acct-on-off-group [group-name]
Context
[Tree] (show>aaa acct-on-off-group)
Full Context
show aaa acct-on-off-group
Description
This command displays Acct-On-Off group information and the associated RADIUS server policies.
Parameters
- group-name
-
Displays information pertaining to the specified acct-on-off group.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of AAA Acct-On-Off group information.
Output Example# show aaa acct-on-off-group "group-1"
===============================================================================
Acct-On-Off-Group Information
===============================================================================
acct on off group name : group-1
- controlling Radius-Server-policy :
aaa-server-policy-3
- monitored by Radius-Server-policy :
aaa-server-policy-4
-------------------------------------------------------------------------------
Nbr of Acct-on-off-groups displayed : 1
-------------------------------------------------------------------------------
===============================================================================
Label |
Description |
---|---|
acct on off group name |
The name of a RADIUS server policy Accounting-On-Off-Group |
controlling Radius-Server-policy |
The controlling RADIUS server policy name |
monitored by Radius-Server-policy |
The policy monitored a RADIUS server policy. |
Nbr of Acct-on-off-groups displayed |
The RADIUS policy that controls the Acct-On-Off group |
accu-stats
accu-stats
Syntax
accu-stats subscriber subscriber-id
Context
[Tree] (show>subscriber-mgmt accu-stats)
Full Context
show subscriber-mgmt accu-stats
Description
This command displays the accumulated statistics for both online and offline statistics.
Parameters
- subscriber-id
-
Specifies the subscriber ID, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber statistics.
Output ExampleA:active# show subscriber-mgmt accu-stats subscriber home-1
===============================================================================
Subscriber accumulated statistics for "home-1”
===============================================================================
-------------------------------------------------------------------------------
Subscriber accumulated statistics ingress queue 1
-------------------------------------------------------------------------------
packets octets
-------------------------------------------------------------------------------
Offered high priority 0 0
Offered low priority 0 0
Dropped high priority 0 0
Dropped low priority 0 0
Forwarded in-profile 0 0
Forwarded out-of-profile 0 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Subscriber accumulated statistics egress queue 1
-------------------------------------------------------------------------------
packets octets
Forwarded in-profile 0 0
Forwarded out-of-profile 0 0
Dropped in-profile 0 0
Dropped out-of--profile 0 0
-------------------------------------------------------------------------------
===============================================================================
Accumulated Statistics Field Descriptions describes accumulated statistics output fields.
Field |
Description |
---|---|
packets |
The number of packets associated with this policy |
octets |
The number of octets associated with this policy |
Offered high priority |
The number of offered high priority packets or octets |
Offered low priority |
The number of offered low priority packets or octets |
Dropped high priority |
The number of dropped high priority packets or octets |
Forwarded in-profile |
The number of forwarded in-profile packets or octets |
Forwarded out-of-profile |
The number of forwarded out-of-profile packets or octets |
Dropped in-profile |
The number of dropped in-profile packets or octets |
Dropped out-of-profile |
The number of dropped out-of-profile packets or octets |
accu-stats
Syntax
accu-stats active-subs no-accu-stats-policy
accu-stats active-subs sub-profile profile-name
accu-stats inactive-subs
accu-stats subscriber subscriber-id
Context
[Tree] (clear>subscriber-mgmt accu-stats)
Full Context
clear subscriber-mgmt accu-stats
Description
This command removes the accumulated statistics for a subscriber.
Parameters
- active-subs no accu-stats-policy
-
Removes the accumulated statistics that are no longer associated with an accu-stats-policy. These are active subscribers that are referencing a subscriber profile that removed an accu-stats-policy.
- active-subs sub-profile profile-name
-
Removes the accumulated statistics for the specified subscriber profile.
- inactive-subs
-
Removes the accumulated statistics from all inactive subscribers.
- profile-name
-
Specifies the subscriber profile up to 32 characters.
- subscriber-id
-
Specifies the subscriber up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
accu-stats-policy
accu-stats-policy
Syntax
accu-stats-policy
accu-stats-policy policy-name [associations]
Context
[Tree] (show>subscriber-mgmt accu-stats-policy)
Full Context
show subscriber-mgmt accu-stats-policy
Description
This command displays the configuration of the accumulated statistics policy for the subscriber profile that referenced the accumulated statistics policy.
Parameters
- policy-name
-
Specifies the policy name, up to 32 characters.
- associations
-
Lists the sub-profile that referenced the policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management accumulated statistics information.
Output ExampleA:active# show subscriber-mgmt accu-stats-policy "accu-stats-policy-01” associations
===============================================================================
Subscriber profile associations
===============================================================================
no-prof
sub-prof
-------------------------------------------------------------------------------
===============================================================================
No. of subscriber profiles: 2
===============================================================================
A:active# show subscriber-mgmt accu-stats-policy "accu-stats-policy-01”
===============================================================================
Subscriber accumulated statistics policy accu-stats-policy-01
===============================================================================
Description : (Not Specified)
Last management change : 09/23/2016 16:48:46
===============================================================================
===============================================================================
Entries
===============================================================================
Direction Type Id
-------------------------------------------------------------------------------
ingress queue 1
egress queue 1
===============================================================================
Accumulated Statistics Policy Field Descriptions describes subscriber management accumulated statistics policy fields.
Field |
Description |
---|---|
Description |
The user provided description of this policy |
Last management change |
The date and time of the last management change |
Direction Type |
The specific direction for the policer or the queue to be stored, ingress or egress |
ID |
The queue ID |
No. of subscriber profiles |
The number of entries matching the search criteria |
accu-stats-subscribers
accu-stats-subscribers
Syntax
accu-stats-subscribers [subscriber sub-ident] [ sub-profile name]
Context
[Tree] (show>subscriber-mgmt accu-stats-subscribers)
Full Context
show subscriber-mgmt accu-stats-subscribers
Description
This command lists all subscribers on the system that had referenced an accumulated statistics policy. The list contains subscribers that are currently referencing an accu-stats-policy as well as subscribers that no longer reference an accu-stats-policy (due to removal of the policy from the subscriber profile).
Parameters
- sub-ident
-
Specifies a specific subscriber ID, up to 32 characters.
- sub-profile name
-
Lists all subscribers that are referencing the specified subscriber profile, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management accumulated statistics information.
Output Example*DUT# show subscriber-mgmt accu-stats-subscribers
===============================================================================
Subscribers with accumulated statistics
===============================================================================
Subscriber : home-1
Subscriber profile : no-prof
Accumulated-stats policy : accu-stats-policy-01
-------------------------------------------------------------------------------
Subscriber : home-2
Subscriber profile : no-prof
Accumulated-stats policy : accu-stats-policy-02
-------------------------------------------------------------------------------
Subscriber : twamp-host
Subscriber profile : no-prof
Accumulated-stats policy : (Unknown)
-------------------------------------------------------------------------------
No. of Subscribers with accumulated statistics: 3
===============================================================================
Output Example
The show subscriber-mgmt status system command shows the number of subscribers using accumulated statistics and whether the statistics usage has reached the peak value.
*A:Dut-C# show subscriber-mgmt status system
===============================================================================
Subscriber Management System Status
===============================================================================
Chassis 1
-------------------------------------------------------------------------------
Memory usage high : No
DHCP message processing overload : No
Statistics usage high : Yes
Number of subscribers using statistics : 131072
Data-trigger statistics
-------------------------------------------------------------------------------
Packets received : 0
Packets dropped : 0
Packets in queue (actual) : 0
Packets in queue (peak) : 0
Bridged Residential Gateway statistics
-------------------------------------------------------------------------------
BRG initialized : 0
BRG operational : 0
BRG in connectivity verification : 0
BRG on hold : 0
BRG authenticated by proxy : 0
===============================================================================
Status System Field Descriptions describes subscriber management status system fields.
Field |
Description |
---|---|
Chassis |
The chassis number |
Memory usage high |
The memory usage of the subscriber management function on this chassis is near the limit; Yes or No |
DHCP message processing overload |
The subscriber management DHCP message processing function is in overload; Yes or No |
Statistics usage high |
The memory used for subscriber statistics on this chassis is near the limit; Yes or No |
Number of subscribers using statistics |
The number of subscribers using memory to store accumulated statistics |
Packets received |
The number of data packets received that may trigger creation of data-triggered subscriber hosts on this system |
Packets dropped |
The number of data packets dropped that could have triggered creation of data-triggered subscriber hosts on this system |
Packets in queue (actual) |
The number of data packets currently in the waiting queue that may trigger creation of data-triggered subscriber hosts on this system |
Packets in queue (peak) |
The maximum value of the packets in queue object since the start up of this system or the last time that the value of packets in queue was reset |
BRG initialized |
The number of BRGs with the init timer running; waiting for the first host |
BRG operational |
The number of BRGs in the normal operating state, with dynamic hosts |
BRG in connectivity verification |
The number of BRGs with no hosts, pinging the residential gateway |
BRG on hold |
The number of BRGs with no hosts attached, in hold |
BRG authenticated by proxy |
The number of BRGs in this system |
activate-best-dest
activate-best-dest
Syntax
activate-best-dest
Context
[Tree] (tools>perform>filter>redirect-policy activate-best-dest)
Full Context
tools perform filter redirect-policy activate-best-dest
Description
This command allows the operator to force a PBR switch to the best destination selected by the redirect policy when that destination is not currently active as result of sticky destination functionality being enabled for the specified redirect policy. If hold-time-up is running, the timer is also expired.
Platforms
All
activate-primary-action
activate-primary-action
Syntax
activate-primary-action
Context
[Tree] (tools>perform>filter>mac-filter>entry activate-primary-action)
[Tree] (tools>perform>filter>ip-filter>entry activate-primary-action)
[Tree] (tools>perform>filter>ipv6-filter>entry activate-primary-action)
Full Context
tools perform filter mac-filter entry activate-primary-action
tools perform filter ip-filter entry activate-primary-action
tools perform filter ipv6-filter entry activate-primary-action
Description
This command allows an operator to activate the primary action for the given filter policy entry. If the primary action is already active, the command has no effect. If a secondary action is active, the primary action will be activated unless the primary target is down. If the sticky destination timer is running for the primary action entry, it will expire.
Platforms
All
active
active
Syntax
active egress-lsp [tunnel-id]
active detail [family] [egress-if port-id]
active detail [family] [egress-lsp tunnel-id]
active detail [egress-nh ip-address] [family]
active egress-if port-id [summary | detail] [ family]
active egress-lsp tunnel-id [summary | detail] [family]
active egress-nh [family] [summary | detail] ip-address
active ipv4 [summary | detail] [ egress-if port-id]
active ipv4 [summary | detail] [ egress-lsp tunnel-id]
active ipv4 [summary | detail] [ egress-nh ip-address]
active ipv6 [summary | detail] [egress-if port-id]
active ipv6 [summary | detail] [ egress-nh ip-address]
active ipv6 [summary | detail] [ egress-lsp tunnel-id]
active p2mp p2mp-id identifier root ip-address [summary | detail] [ egress-if port-id]
active p2mp p2mp-id identifier root ip-address [ summary | detail] [egress-lsp tunnel-id]
active p2mp p2mp-id identifier root ip-address [summary | detail] [egress-nh ip-address]
active p2mp p2mp-id identifier root ip-address [rd rd] [ summary | detail] [egress-if port-id] inner-root ip-address
active p2mp p2mp-id identifier root ip-address [ rd rd] [summary | detail] [ egress-lsp tunnel-id] inner-root ip-address
active p2mp p2mp-id identifier root ip-address [rd rd] [summary | detail] [egress-nh ip-address] inner-root ip-address
active p2mp [family] [summary | detail] [ egress-if port-id] [opaque-type opaque-type]
active p2mp [family] [summary | detail] [ egress-lsp tunnel-id] [opaque-type opaque-type]
active p2mp [family] [summary | detail] [ egress-nh ip-address] [opaque-type opaque-type]
active p2mp source ip-address group mcast-address root ip-address [summary | detail] [ egress-if port-id] inner-root ip-address
active p2mp source ip-address group mcast-address root ip-address [summary | detail] [ egress-lsp tunnel-id] inner-root ip-address
active p2mp source ip-address group mcast-address root ip-address [summary | detail] [ egress-nh ip-address] inner-root ip-address
active p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [egress-if port-id]
active p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [egress-lsp tunnel-id]
active p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [egress-nh ip-address]
active p2mp source ip-address group mcast-address root ip-address [rd rd] [ summary | detail] [innermost-root ip-address]
active prefixes [family] [summary | detail] [ egress-if port-id] [community community]
active prefixes [family] [summary | detail] [ egress-lsp tunnel-id] [community community]
active prefixes [egress-nh ip-address] [ family] [summary | detail] [ community community]
active prefixes prefix ip-prefix/ip-prefix-length [ summary | detail] [egress-if port-id] [community community]
active prefixes prefix ip-prefix/ip-prefix-length [summary | detail] [egress-lsp tunnel-id] [ community community]
active prefixes prefix ip-prefix/ip-prefix-length [egress-nh ip-address] [summary | detail] [ community community]
active summary [family] [egress-if port-id]
active summary [family] [egress-lsp tunnel-id]
active summary [egress-nh ip-address] [family]
Context
[Tree] (show>router>ldp>bindings active)
Full Context
show router ldp bindings active
Description
This command display information about LDP active bindings.
Parameters
- detail
-
Displays detailed information.
- summary
-
Displays information in a summarized format.
- family
-
Displays either IPv4 or IPv6 active LDP information.
- opaque-type opaque-type
-
Specifies the type of a Multi-Point Opaque Value Element.
- egress-lsp tunnel-id
-
Displays LDP active bindings by matching on the egress RSVP-TE LSP tunnel-id for LDP FECs which are tunneled over a RSVP-TE LSP. The tunnel-id for the RSVP-TE LSP can be found in the output of the show router mpls lsp detail command and in the show router tunnel-table command. It is not the path LSP ID shown in the output of the show router mpls lsp path detail command.
- egress-nh ip-address
-
Displays LDP active bindings by matching egress-nh.
- egress-if port-id
-
Displays LDP active bindings by matching egress-if.
- inner-root ip-address
-
Displays recursive FECs whose inner root address matches the specified address.
- innermost-root ip-address
-
Displays recursive FECs whose inner root address matches the specified address and non-recursive FECs that have a root address that matches the specified address.
- p2mp source ip-address
-
Displays LDP active P2MP source bindings.
- p2mp-id identifier
-
Displays LDP active P2MP identifier bindings.
- group mcast-address
-
Displays the P2MP group multicast address bindings.
- root ip-address
-
Displays root IP address information.
- rd rd
-
Displays information for the route distinguisher.
- prefix ip-prefix/ip-prefix-length
-
Specifies information for the specified IP prefix and mask length.
- community
-
The string defining the LDP community assigned to the session. Allowed values are any string up to 32 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
Output
Output Example*A:Dut-C# show router ldp bindings active
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, M - Community Mismatch, BA - ASBR Backup FEC
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(I) - SR-ISIS Next Hop (O) - SR-OSPF Next Hop
(C) - FEC resolved with class-based-forwarding
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.1/32 Push -- 262143
10.10.2.1 1/1/1
10.20.1.1/32 Swap 262141 262143
10.10.2.1 1/1/1
10.20.1.2/32 Push -- 262143
10.10.12.2 lag-1
10.20.1.2/32 Swap 262140 262143
10.10.12.2 lag-1
10.20.1.3/32 Pop 262143 --
-- --
10.20.1.4/32 Push -- 262143
10.10.11.4 2/1/2
10.20.1.4/32 Swap 262139 262143
10.10.11.4 2/1/2
10.20.1.5/32 Push -- 262143
10.10.5.5 2/1/1
10.20.1.5/32 Swap 262137 262143
10.10.5.5 2/1/1
10.20.1.6/32 Push -- 262137
10.10.11.4 2/1/2
10.20.1.6/32 Swap 262135 262137
10.10.11.4 2/1/2
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 11
===============================================================================
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:101/128 Push -- 262142
fe80::21 1/1/1
3ffe::a14:101/128 Swap 262136 262142
fe80::21 1/1/1
3ffe::a14:102/128 Push -- 262142
fe80::122 lag-1
3ffe::a14:102/128 Swap 262138 262142
fe80::122 lag-1
3ffe::a14:103/128 Pop 262142 --
-- --
3ffe::a14:104/128 Push -- 262142
fe80::114 2/1/2
3ffe::a14:104/128 Swap 262134 262142
fe80::114 2/1/2
3ffe::a14:105/128 Push -- 262142
fe80::55 2/1/1
3ffe::a14:105/128 Swap 262132 262142
fe80::55 2/1/1
3ffe::a14:106/128 Push -- 262136
fe80::114 2/1/2
3ffe::a14:106/128 Swap 262133 262136
fe80::114 2/1/2
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 11
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Generic IPv6 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-C# show router ldp bindings active detail
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
==============================================================================
LDP IPv4 Prefix Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
Prefix : 10.20.1.1/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : 1/1/1
EgrNextHop : 10.10.2.1
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.1/32
Op : Swap
Ing Lbl : 262141 Egr Lbl : 262143
Egr Int/LspId : 1/1/1
EgrNextHop : 10.10.2.1
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.2/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : lag-1
EgrNextHop : 10.10.12.2
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.12.3
Metric : 333 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.2/32
Op : Swap
Ing Lbl : 262140 Egr Lbl : 262143
Egr Int/LspId : lag-1
EgrNextHop : 10.10.12.2
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.12.3
Metric : 333 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.3/32
Op : Pop
Ing Lbl : 262143 Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
Prefix : 10.20.1.4/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : 2/1/2
EgrNextHop : 10.10.11.4
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.4/32
Op : Swap
Ing Lbl : 262139 Egr Lbl : 262143
Egr Int/LspId : 2/1/2
EgrNextHop : 10.10.11.4
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.5/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : 2/1/1
EgrNextHop : 10.10.5.5
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.5.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.5/32
Op : Swap
Ing Lbl : 262137 Egr Lbl : 262143
Egr Int/LspId : 2/1/1
EgrNextHop : 10.10.5.5
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.5.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.6/32
Op : Push
Ing Lbl : -- Egr Lbl : 262137
Egr Int/LspId : 2/1/2
EgrNextHop : 10.10.11.4
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 2000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.6/32
Op : Swap
Ing Lbl : 262135 Egr Lbl : 262137
Egr Int/LspId : 2/1/2
EgrNextHop : 10.10.11.4
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 2000 Mtu : 1500
===============================================================================
No. of IPv4 Prefix Active Bindings: 11
==============================================================================
==============================================================================
LDP IPv6 Prefix Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:101/128
Op : Push
Ing Lbl : -- Egr Lbl : 262142
Egr Int/LspId : 1/1/1
EgrNextHop : fe80::21
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:101/128
Op : Swap
Ing Lbl : 262136 Egr Lbl : 262142
Egr Int/LspId : 1/1/1
EgrNextHop : fe80::21
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:102/128
Op : Push
Ing Lbl : -- Egr Lbl : 262142
Egr Int/LspId : lag-1
EgrNextHop : fe80::122
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.12.3
Metric : 333 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:102/128
Op : Swap
Ing Lbl : 262138 Egr Lbl : 262142
Egr Int/LspId : lag-1
EgrNextHop : fe80::122
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.12.3
Metric : 333 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:103/128
Op : Pop
Ing Lbl : 262142 Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:104/128
Op : Push
Ing Lbl : -- Egr Lbl : 262142
Egr Int/LspId : 2/1/2
EgrNextHop : fe80::114
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:104/128
Op : Swap
Ing Lbl : 262134 Egr Lbl : 262142
Egr Int/LspId : 2/1/2
EgrNextHop : fe80::114
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:105/128
Op : Push
Ing Lbl : -- Egr Lbl : 262142
Egr Int/LspId : 2/1/1
EgrNextHop : fe80::55
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.5.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:105/128
Op : Swap
Ing Lbl : 262132 Egr Lbl : 262142
Egr Int/LspId : 2/1/1
EgrNextHop : fe80::55
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.5.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:106/128
Op : Push
Ing Lbl : -- Egr Lbl : 262136
Egr Int/LspId : 2/1/2
EgrNextHop : fe80::114
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 2000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:106/128
Op : Swap
Ing Lbl : 262133 Egr Lbl : 262136
Egr Int/LspId : 2/1/2
EgrNextHop : fe80::114
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.11.3
Metric : 2000 Mtu : 1500
===============================================================================
No. of IPv6 Prefix Active Bindings: 11
==============================================================================
==============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
==============================================================================
No Matching Entries Found
==============================================================================
==============================================================================
LDP Generic IPv6 P2MP Bindings (Active)
==============================================================================
No Matching Entries Found
==============================================================================
==============================================================================
LDP In-Band-SSM IPv4 P2MP Bindings (Active)
==============================================================================
No Matching Entries Found
==============================================================================
==============================================================================
LDP In-Band-SSM IPv6 P2MP Bindings (Active)
==============================================================================
No Matching Entries Found
==============================================================================
==============================================================================
LDP In-Band-VPN-SSM IPv4 P2MP Bindings (Active)
==============================================================================
No Matching Entries Found
==============================================================================
==============================================================================
LDP In-Band-VPN-SSM IPv6 P2MP Bindings (Active)
==============================================================================
No Matching Entries Found
==============================================================================
*A:Dut-C# show router ldp bindings active egress-if 2/1/2
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.4/32 Push -- 262143
10.10.11.4 2/1/2
10.20.1.4/32 Swap 262139 262143
10.10.11.4 2/1/2
10.20.1.6/32 Push -- 262137
10.10.11.4 2/1/2
10.20.1.6/32 Swap 262135 262137
10.10.11.4 2/1/2
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 4
===============================================================================
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:104/128 Push -- 262142
fe80::114 2/1/2
3ffe::a14:104/128 Swap 262134 262142
fe80::114 2/1/2
3ffe::a14:106/128 Push -- 262136
fe80::114 2/1/2
3ffe::a14:106/128 Swap 262133 262136
fe80::114 2/1/2
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 4
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Generic IPv6 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-C# show router ldp bindings active egress-nh 10.10.11.4
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.4/32 Push -- 262143
10.10.11.4 2/1/2
10.20.1.4/32 Swap 262139 262143
10.10.11.4 2/1/2
10.20.1.6/32 Push -- 262137
10.10.11.4 2/1/2
10.20.1.6/32 Swap 262135 262137
10.10.11.4 2/1/2
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 4
===============================================================================
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Generic IPv6 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-C# show router ldp bindings active ipv4
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.1/32 Push -- 262143
10.10.2.1 1/1/1
10.20.1.1/32 Swap 262141 262143
10.10.2.1 1/1/1
10.20.1.2/32 Push -- 262143
10.10.12.2 lag-1
10.20.1.2/32 Swap 262140 262143
10.10.12.2 lag-1
10.20.1.3/32 Pop 262143 --
-- --
10.20.1.4/32 Push -- 262143
10.10.11.4 2/1/2
10.20.1.4/32 Swap 262139 262143
10.10.11.4 2/1/2
10.20.1.5/32 Push -- 262143
10.10.5.5 2/1/1
10.20.1.5/32 Swap 262137 262143
10.10.5.5 2/1/1
10.20.1.6/32 Push -- 262137
10.10.11.4 2/1/2
10.20.1.6/32 Swap 262135 262137
10.10.11.4 2/1/2
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 11
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv4 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-C# show router ldp bindings active ipv6
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:101/128 Push -- 262142
fe80::21 1/1/1
3ffe::a14:101/128 Swap 262136 262142
fe80::21 1/1/1
3ffe::a14:102/128 Push -- 262142
fe80::122 lag-1
3ffe::a14:102/128 Swap 262138 262142
fe80::122 lag-1
3ffe::a14:103/128 Pop 262142 --
-- --
3ffe::a14:104/128 Push -- 262142
fe80::114 2/1/2
3ffe::a14:104/128 Swap 262134 262142
fe80::114 2/1/2
3ffe::a14:105/128 Push -- 262142
fe80::55 2/1/1
3ffe::a14:105/128 Swap 262132 262142
fe80::55 2/1/1
3ffe::a14:106/128 Push -- 262136
fe80::114 2/1/2
3ffe::a14:106/128 Swap 262133 262136
fe80::114 2/1/2
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 11
===============================================================================
===============================================================================
LDP Generic IPv6 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP In-Band-VPN-SSM IPv6 P2MP Bindings (Active)
===============================================================================
Source
Group RD Op
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-C# show router ldp bindings active summary
No. of IPv4 Prefix Active Bindings: 11
No. of IPv6 Prefix Active Bindings: 11
No. of Generic IPv4 P2MP Active Bindings: 0
No. of Generic IPv6 P2MP Active Bindings: 0
No. of In-Band-SSM IPv4 P2MP Active Bindings: 0
No. of In-Band-SSM IPv6 P2MP Active Bindings: 0
No. of In-Band-VPN-SSM IPv4 P2MP Active Bindings: 0
No. of In-Band-VPN-SSM IPv6 P2MP Active Bindings: 0
*A:Dut-C#
*A:Dut-C# show router ldp bindings active prefixes
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.1/32 Push -- 262143
10.10.2.1 1/1/1
10.20.1.1/32 Swap 262141 262143
10.10.2.1 1/1/1
10.20.1.2/32 Push -- 262143
10.10.12.2 lag-1
10.20.1.2/32 Swap 262140 262143
10.10.12.2 lag-1
10.20.1.3/32 Pop 262143 --
-- --
10.20.1.4/32 Push -- 262143
10.10.11.4 2/1/2
10.20.1.4/32 Swap 262139 262143
10.10.11.4 2/1/2
10.20.1.5/32 Push -- 262143
10.10.5.5 2/1/1
10.20.1.5/32 Swap 262137 262143
10.10.5.5 2/1/1
10.20.1.6/32 Push -- 262137
10.10.11.4 2/1/2
10.20.1.6/32 Swap 262135 262137
10.10.11.4 2/1/2
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 11
===============================================================================
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:101/128 Push -- 262142
fe80::21 1/1/1
3ffe::a14:101/128 Swap 262136 262142
fe80::21 1/1/1
3ffe::a14:102/128 Push -- 262142
fe80::122 lag-1
3ffe::a14:102/128 Swap 262138 262142
fe80::122 lag-1
3ffe::a14:103/128 Pop 262142 --
-- --
3ffe::a14:104/128 Push -- 262142
fe80::114 2/1/2
3ffe::a14:104/128 Swap 262134 262142
fe80::114 2/1/2
3ffe::a14:105/128 Push -- 262142
fe80::55 2/1/1
3ffe::a14:105/128 Swap 262132 262142
fe80::55 2/1/1
3ffe::a14:106/128 Push -- 262136
fe80::114 2/1/2
3ffe::a14:106/128 Swap 262133 262136
fe80::114 2/1/2
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 11
===============================================================================
*A:Dut-C#
*A:Dut-C# show router ldp bindings active prefixes ipv4
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.1/32 Push -- 262143
10.10.2.1 1/1/1
10.20.1.1/32 Swap 262141 262143
10.10.2.1 1/1/1
10.20.1.2/32 Push -- 262143
10.10.12.2 lag-1
10.20.1.2/32 Swap 262140 262143
10.10.12.2 lag-1
10.20.1.3/32 Pop 262143 --
-- --
10.20.1.4/32 Push -- 262143
10.10.11.4 2/1/2
10.20.1.4/32 Swap 262139 262143
10.10.11.4 2/1/2
10.20.1.5/32 Push -- 262143
10.10.5.5 2/1/1
10.20.1.5/32 Swap 262137 262143
10.10.5.5 2/1/1
10.20.1.6/32 Push -- 262137
10.10.11.4 2/1/2
10.20.1.6/32 Swap 262135 262137
10.10.11.4 2/1/2
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 11
===============================================================================
*A:Dut-C#
*A:Dut-C# show router ldp bindings active prefixes ipv6
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:101/128 Push -- 262142
fe80::21 1/1/1
3ffe::a14:101/128 Swap 262136 262142
fe80::21 1/1/1
3ffe::a14:102/128 Push -- 262142
fe80::122 lag-1
3ffe::a14:102/128 Swap 262138 262142
fe80::122 lag-1
3ffe::a14:103/128 Pop 262142 --
-- --
3ffe::a14:104/128 Push -- 262142
fe80::114 2/1/2
3ffe::a14:104/128 Swap 262134 262142
fe80::114 2/1/2
3ffe::a14:105/128 Push -- 262142
fe80::55 2/1/1
3ffe::a14:105/128 Swap 262132 262142
fe80::55 2/1/1
3ffe::a14:106/128 Push -- 262136
fe80::114 2/1/2
3ffe::a14:106/128 Swap 262133 262136
fe80::114 2/1/2
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 11
===============================================================================
*A:Dut-C#
*A:Dut-C# show router ldp bindings active prefixes prefix 3ffe::a14:101/128 detail
egress-if 1/1/1
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
==============================================================================
LDP IPv6 Prefix Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:101/128
Op : Push
Ing Lbl : -- Egr Lbl : 262142
Egr Int/LspId : 1/1/1
EgrNextHop : fe80::21
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:101/128
Op : Swap
Ing Lbl : 262136 Egr Lbl : 262142
Egr Int/LspId : 1/1/1
EgrNextHop : fe80::21
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
===============================================================================
No. of IPv6 Prefix Active Bindings: 2
==============================================================================
*A:Dut-C#
*A:Dut-C# show router ldp bindings active prefixes prefix 3ffe::a14:101/128 egress-
nh fe80::21
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:101/128 Push -- 262142
fe80::21 1/1/1
3ffe::a14:101/128 Swap 262136 262142
fe80::21 1/1/1
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 2
===============================================================================
*A:Dut-C#
*A:SRU4# show router ldp bindings active p2mp
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
8193 77156
192.168.1.1 Pop 255042 --
-- --
8193 77156
192.168.1.1 Swap 255042 259773
192.168.110.110 3/1/5:1
8193 77156
192.168.1.1 Pop 258780BU --
-- --
8193 77156
192.168.1.1 Swap 258780BU 259773
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Pop 255041 --
-- --
8194 77157
192.168.1.1 Swap 255041 259772
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Pop 258779BU --
-- --
8194 77157
192.168.1.1 Swap 258779BU 259772
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Pop 255040 --
-- --
8195 77158
192.168.1.1 Swap 255040 259769
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Pop 258777BU --
-- --
8195 77158
192.168.1.1 Swap 258777BU 259769
*A:SRU4#
The following show output displays recursive FECs.
A:Dut-C# show router ldp bindings active p2mp
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
LF - Lower FEC, UF - Upper FEC
===============================================================================
LDP Recursive with In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
RootAddr
InnerRootAddr
Source Interface
Group Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
10.4.0.2
10.20.1.6
10.0.101.10 73728
192.168.1.1 Pop 262135 --
-- --
10.4.0.2 (UF)
10.20.1.6
10.0.101.10 73728
192.168.1.1 Swap 262135 Stitched
-- --
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.3.0.1 lag-1
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.33.0.1 1/1/2:2
-------------------------------------------------------------------------------
No. of In-Band-SSM IPv4 P2MP Active Bindings: 4
===============================================================================
*A:SRU4# show router ldp bindings active p2mp p2mp-id 1 root 192.168.1.2
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
1 73728
192.168.1.2 Pop 253348 --
-- --
1 73728
192.168.1.2 Swap 253348 256245
192.168.58.6 3/2/3:8
1 73728
192.168.1.2 Pop 260103BU --
-- --
1 73728
192.168.1.2 Swap 260103BU 256245
192.168.58.6 3/2/3:8
-------------------------------------------------------------------------------
No. of Generic IPv4 P2MP Active Bindings: 4
===============================================================================
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp p2mp-id 1 root 192.168.1.2 summary
No. of Generic IPv4 P2MP Active Bindings: 4
*A:SRU4# show router ldp bindings active p2mp p2mp-id 1 root 192.168.1.2 detail
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
==============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 192.168.1.2
-------------------------------------------------------------------------------
Op : Pop
Ing Lbl : 253348
Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 192.168.1.2
-------------------------------------------------------------------------------
Op : Swap
Ing Lbl : 253348
Egr Lbl : 256245
Egr Int/LspId : 3/2/3:8
EgrNextHop : 192.168.58.6
Egr. Flags : None Ing. Flags : None
Egr If Name : src-1.8
Metric : 1 Mtu : 1500
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 192.168.1.2
-------------------------------------------------------------------------------
Op : Pop
Ing Lbl : 260103BU
Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 192.168.1.2
-------------------------------------------------------------------------------
Op : Swap
Ing Lbl : 260103BU
Egr Lbl : 256245
Egr Int/LspId : 3/2/3:8
EgrNextHop : 192.168.58.6
Egr. Flags : None Ing. Flags : None
Egr If Name : src-1.8
Metric : 1 Mtu : 1500
===============================================================================
No. of Generic IPv4 P2MP Active Bindings: 4
==============================================================================
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp p2mp-
id 1 root 192.168.1.2 detail egress-
if 3/2/3:8
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
==============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 192.168.1.2
-------------------------------------------------------------------------------
Op : Swap
Ing Lbl : 253348
Egr Lbl : 256245
Egr Int/LspId : 3/2/3:8
EgrNextHop : 192.168.58.6
Egr. Flags : None Ing. Flags : None
Egr If Name : src-1.8
Metric : 1 Mtu : 1500
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 192.168.1.2
-------------------------------------------------------------------------------
Op : Swap
Ing Lbl : 260103BU
Egr Lbl : 256245
Egr Int/LspId : 3/2/3:8
EgrNextHop : 192.168.58.6
Egr. Flags : None Ing. Flags : None
Egr If Name : src-1.8
Metric : 1 Mtu : 1500
===============================================================================
No. of Generic IPv4 P2MP Active Bindings: 2
==============================================================================
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp p2mp-id 1 root 192.168.1.2 egress-nh
192.168.58.6
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
1 73728
192.168.1.2 Swap 253348 256245
192.168.58.6 3/2/3:8
1 73728
192.168.1.2 Swap 260103BU 256245
192.168.58.6 3/2/3:8
-------------------------------------------------------------------------------
No. of Generic IPv4 P2MP Active Bindings: 2
===============================================================================
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp ipv4 summary
No. of Generic IPv4 P2MP Active Bindings: 8870
No. of In-Band-SSM IPv4 P2MP Active Bindings: 182
No. of In-Band-VPN-SSM IPv4 P2MP Active Bindings: 0
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp ipv4 detail
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
==============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 192.168.1.1
-------------------------------------------------------------------------------
Op : Pop
Ing Lbl : 255042
Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 192.168.1.1
-------------------------------------------------------------------------------
Op : Swap
Ing Lbl : 255042
Egr Lbl : 259773
Egr Int/LspId : 3/1/5:1
EgrNextHop : 192.168.110.110
Egr. Flags : None Ing. Flags : None
Egr If Name : sicily1-1:1
Metric : 1 Mtu : 9194
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 192.168.1.1
-------------------------------------------------------------------------------
Op : Pop
Ing Lbl : 258780BU
Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 192.168.1.1
-------------------------------------------------------------------------------
Op : Swap
Ing Lbl : 258780BU
Egr Lbl : 259773
Egr Int/LspId : 3/1/5:1
EgrNextHop : 192.168.110.110
Egr. Flags : None Ing. Flags : None
Egr If Name : sicily1-1:1
Metric : 1 Mtu : 9194
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8194
Root-Addr : 192.168.1.1
-------------------------------------------------------------------------------
Op : Pop
Ing Lbl : 255041
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp ipv4 egress-if 3/1/5:1
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
8193 77156
192.168.1.1 Swap 255042 259773
192.168.110.110 3/1/5:1
8193 77156
192.168.1.1 Swap 258780BU 259773
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Swap 255041 259772
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Swap 258779BU 259772
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Swap 255040 259769
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Swap 258777BU 259769
192.168.110.110 3/1/5:1
8196 77159
192.168.1.1 Swap 255039 259768
192.168.110.110 3/1/5:1
8196 77159
192.168.1.1 Swap 258772BU 259768
192.168.110.110 3/1/5:1
8197 77160
192.168.1.1 Swap 255034 259762
192.168.110.110 3/1/5:1
8197 77160
192.168.1.1 Swap 258758BU 259762
192.168.110.110 3/1/5:1
8198 77161
192.168.1.1 Swap 255033 259761
192.168.110.110 3/1/5:1
8198 77161
192.168.1.1 Swap 258755BU 259761
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp ipv4 egress-nh 192.168.110.110
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
8193 77156
192.168.1.1 Swap 255042 259773
192.168.110.110 3/1/5:1
8193 77156
192.168.1.1 Swap 258780BU 259773
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Swap 255041 259772
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Swap 258779BU 259772
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Swap 255040 259769
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Swap 258777BU 259769
192.168.110.110 3/1/5:1
8196 77159
192.168.1.1 Swap 255039 259768
192.168.110.110 3/1/5:1
8196 77159
192.168.1.1 Swap 258772BU 259768
192.168.110.110 3/1/5:1
8197 77160
192.168.1.1 Swap 255034 259762
192.168.110.110 3/1/5:1
8197 77160
192.168.1.1 Swap 258758BU 259762
192.168.110.110 3/1/5:1
8198 77161
192.168.1.1 Swap 255033 259761
192.168.110.110 3/1/5:1
8198 77161
192.168.1.1 Swap 258755BU 259761
*A:SRU4#
*A:SRU4# show router ldp bindings active p2mp ipv4 egress-if 3/1/5:1 opaque-type
generic
===============================================================================
LDP Bindings (IPv4 LSR ID 192.168.1.4:0)
(IPv6 LSR ID 3ffe::6e14:104[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
8193 77156
192.168.1.1 Swap 255042 259773
192.168.110.110 3/1/5:1
8193 77156
192.168.1.1 Swap 258780BU 259773
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Swap 255041 259772
192.168.110.110 3/1/5:1
8194 77157
192.168.1.1 Swap 258779BU 259772
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Swap 255040 259769
192.168.110.110 3/1/5:1
8195 77158
192.168.1.1 Swap 258777BU 259769
192.168.110.110 3/1/5:1
8196 77159
192.168.1.1 Swap 255039 259768
192.168.110.110 3/1/5:1
8196 77159
192.168.1.1 Swap 258772BU 259768
192.168.110.110 3/1/5:1
8197 77160
192.168.1.1 Swap 255034 259762
192.168.110.110 3/1/5:1
8197 77160
192.168.1.1 Swap 258758BU 259762
192.168.110.110 3/1/5:1
8198 77161
192.168.1.1 Swap 255033 259761
192.168.110.110 3/1/5:1
8198 77161
192.168.1.1 Swap 258755BU 259761
*A:SRU4#
The following show output displays recursive FECs.
A:Dut-C# show router ldp bindings active p2mp source 10.0.101.10 group 192.168.1.1
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
LF - Lower FEC, UF - Upper FEC
===============================================================================
LDP Recursive with In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
RootAddr
InnerRootAddr
Source Interface
Group Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
10.4.0.2
10.20.1.6
10.0.101.10 73728
192.168.1.1 Pop 262135 --
-- --
10.4.0.2 (UF)
10.20.1.6
10.0.101.10 73728
192.168.1.1 Swap 262135 Stitched
-- --
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.3.0.1 lag-1
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.33.0.1 1/1/2:2
-------------------------------------------------------------------------------
No. of In-Band-SSM IPv4 P2MP Active Bindings: 4
===============================================================================
A:Dut-C# show router ldp bindings active p2mp source 10.0.101.10 group 192.168.1.1
innermost-root 10.20.1.6
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
LF - Lower FEC, UF - Upper FEC
===============================================================================
LDP Recursive with In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
RootAddr
InnerRootAddr
Source Interface
Group Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
10.4.0.2
10.20.1.6
10.0.101.10 73728
192.168.1.1 Pop 262135 --
-- --
10.4.0.2 (UF)
10.20.1.6
10.0.101.10 73728
192.168.1.1 Swap 262135 Stitched
-- --
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.3.0.1 lag-1
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.33.0.1 1/1/2:2
-------------------------------------------------------------------------------
No. of In-Band-SSM IPv4 P2MP Active Bindings: 4
===============================================================================
A:Dut-C# show router ldp bindings active p2mp source 10.0.101.10 group 192.168.1.1
inner-root 10.20.1.6 root 10.20.1.3
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
LF - Lower FEC, UF - Upper FEC
===============================================================================
LDP Recursive with In-Band-SSM IPv4 P2MP Bindings (Active)
===============================================================================
RootAddr
InnerRootAddr
Source Interface
Group Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.3.0.1 lag-1
10.20.1.3 (LF)
10.20.1.6
10.0.101.10 Unknw
192.168.1.1 Push -- 262139
10.33.0.1 1/1/2:2
-------------------------------------------------------------------------------
No. of In-Band-SSM IPv4 P2MP Active Bindings: 2
*A:Dut-C# show router ldp bindings active prefixes prefix 3ffe::a14:101/128
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
3ffe::a14:101/128 Push -- 262142
fe80::21 1/1/1
3ffe::a14:101/128 Swap 262136 262142
fe80::21 1/1/1
-------------------------------------------------------------------------------
No. of IPv6 Prefix Active Bindings: 2
===============================================================================
*A:Dut-C# show router ldp bindings active prefixes prefix 3ffe::a14:101/128 detail
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3:0)
(IPv6 LSR ID 3ffe::a14:103[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
==============================================================================
LDP IPv6 Prefix Bindings (Active)
==============================================================================
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:101/128
Op : Push
Ing Lbl : -- Egr Lbl : 262142
Egr Int/LspId : 1/1/1
EgrNextHop : fe80::21
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 3ffe::a14:101/128
Op : Swap
Ing Lbl : 262136 Egr Lbl : 262142
Egr Int/LspId : 1/1/1
EgrNextHop : fe80::21
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
===============================================================================
No. of IPv6 Prefix Active Bindings: 2
===============================================================================
*A:Dut-C#
*A:Dut-C>config>router>isis# show router ldp bindings active prefixes prefix
10.20.1.1/32
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID 3ffe::a14:103)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, BA - ASBR Backup FEC
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(I) - SR-ISIS Next Hop (O) - SR-OSPF Next Hop
(C) - FEC resolved with class-based-forwarding
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.1/32(I) Swap 262122 474387
10.10.2.1 1/1/1
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 1
===============================================================================
*A:Dut-C>config>router>isis# show router ldp bindings prefixes prefix 10.20.1.1/32
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID 3ffe::a14:103)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, BA - ASBR Backup FEC
===============================================================================
LDP IPv4 Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl
Peer EgrIntf/LspId
EgrNextHop
-------------------------------------------------------------------------------
10.20.1.1/32 262122U 262131
10.20.1.2:0 --
--
10.20.1.1/32 262122U 262140
10.20.1.4:0 --
--
10.20.1.1/32 262122U 262139
10.20.1.5:0 --
--
-------------------------------------------------------------------------------
No. of IPv4 Prefix Bindings: 3
===============================================================================
*A:Dut-C# show router ldp bindings prefixes prefix 10.20.1.6/32
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, BA - ASBR Backup FEC
===============================================================================
LDP IPv4 Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl
Peer EgrIntf/LspId
EgrNextHop
-------------------------------------------------------------------------------
10.20.1.6/32 262142U 262142
10.20.1.1:0 --
--
10.20.1.6/32 262142U --
10.20.1.2:0 --
--
-------------------------------------------------------------------------------
No. of IPv4 Prefix Bindings: 2
===============================================================================
*A:Dut-C# show router ldp bindings active prefixes prefix 10.20.1.6/32
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.3)
(IPv6 LSR ID ::)
===============================================================================
Label Status:
U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
e - Label ELC
FEC Flags:
LF - Lower FEC, UF - Upper FEC, BA - ASBR Backup FEC
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(I) - SR-ISIS Next Hop (O) - SR-OSPF Next Hop
(C) - FEC resolved with class-based-forwarding
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.6/32(B) Swap 262142 262142
10.20.1.2 LspId 65545
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 1
*A:Dut-C# show router ldp bindings active prefixes prefix 10.20.1.3/32
============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.2:0)
(IPv6 LSR ID ::[0])
============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(C) - FEC resolved with class-based-forwarding
============================================================================
LDP IPv4 Prefix Bindings (Active)
============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
----------------------------------------------------------------------------
10.20.1.3/32 Push -- 262143
10.20.1.3 LspId 5
10.20.1.3/32 Push -- 262143
10.20.1.3 LspId 6
10.20.1.3/32 Push -- 262143
10.20.1.3 LspId 7
10.20.1.3/32 Push -- 262143
10.20.1.3 LspId 8
10.20.1.3/32(C) Swap 262141 262143
10.20.1.3 LspId 5
10.20.1.3/32(C) Swap 262141 262143
10.20.1.3 LspId 6
10.20.1.3/32(C) Swap 262141 262143
10.20.1.3 LspId 7
10.20.1.3/32(C) Swap 262141 262143
10.20.1.3 LspId 8
----------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 8
============================================================================
show router ldp bindings active prefixes prefix 10.20.1.3/32 detail
============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.2:0)
(IPv6 LSR ID ::[0])
============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(C) - FEC resolved with class-based-forwarding
============================================================================
LDP IPv4 Prefix Bindings (Active)
============================================================================
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : LspId 5
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_5
Metric : 1000 Mtu : 1492
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : LspId 6
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_6
Metric : 1000 Mtu : 1492
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : LspId 7
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_7
Metric : 1000 Mtu : 1492
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32
Op : Push
Ing Lbl : -- Egr Lbl : 262143
Egr Int/LspId : LspId 8
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_8
Metric : 1000 Mtu : 1492
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32(C)
Op : Swap
Ing Lbl : 262141 Egr Lbl : 262143
Egr Int/LspId : LspId 5
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_5
Metric : 1000 Mtu : 1492
CBF Default LSP: No CBF FC : None
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32(C)
Op : Swap
Ing Lbl : 262141 Egr Lbl : 262143
Egr Int/LspId : LspId 6
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_6
Metric : 1000 Mtu : 1492
CBF Default LSP: No CBF FC : None
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32(C)
Op : Swap
Ing Lbl : 262141 Egr Lbl : 262143
Egr Int/LspId : LspId 7
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_7
Metric : 1000 Mtu : 1492
CBF Default LSP: Yes CBF FC : be l2 af l1 h2 ef h1 nc
----------------------------------------------------------------------------
Prefix : 10.20.1.3/32(C)
Op : Swap
Ing Lbl : 262141 Egr Lbl : 262143
Egr Int/LspId : LspId 8
EgrNextHop : 10.20.1.3
Egr. Flags : None Ing. Flags : None
Lsp Name : B_C_8
Metric : 1000 Mtu : 1492
CBF Default LSP: No CBF FC : None
============================================================================
No. of IPv4 Prefix Active Bindings: 8
============================================================================
active-subscribers
active-subscribers
Syntax
active-subscribers detail
active-subscribers mirror
active-subscribers [summary]
Context
[Tree] (show>service active-subscribers)
Full Context
show service active-subscribers
Description
This command displays active subscriber information.
Parameters
- detail
-
Displays detailed output.
- mirror
-
Displays active subscriber mirror information.
- summary
-
Displays active subscriber information in a brief format.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of active service subscriber information. Active Subscriber Field Descriptions describes the fields.
Output Example*A:Dut-C# show service active-subscribers
===============================================================================
Active Subscribers
===============================================================================
-------------------------------------------------------------------------------
Subscriber hpolSub1 (hpolSubProf2)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
(1) SLA Profile Instance sap:lag-1:2000.1 - sla:hpolSlaProf1
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
239.1.4.194
00:01:00:00:03:c1 PPP 1 IPCP 1000 Y
-------------------------------------------------------------------------------
(2) SLA Profile Instance sap:lag-1:2000.1 - sla:hpolSlaProf2
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
239.1.4.35
00:01:00:00:03:22 N/A ARP-Host 1000 Y
239.1.4.195
00:01:00:00:03:c2 PPP 1 IPCP 1000 Y
-------------------------------------------------------------------------------
Subscriber hpolSub16 (hpolSubProf1)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
(1) SLA Profile Instance sap:[lag-1:2000.2] - sla:hpolSlaProf1
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
239.1.4.224
00:01:00:00:03:df PPP 1 IPCP 1000 Y
-------------------------------------------------------------------------------
Subscriber hpolSub2 (hpolSubProf1)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
(1) SLA Profile Instance sap:lag-1:2000.1 - sla:hpolSlaProf1
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
239.1.4.196
00:01:00:00:03:c3 PPP 1 IPCP 1000 Y
-------------------------------------------------------------------------------
Number of active subscribers : 3
===============================================================================
*A:Dut-C#
*A:EsrC# show service active-subscribers mirror
===============================================================================
Active Subscribers
===============================================================================
Subscriber user1 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.1 00:00:01:00:00:01 Static
Ingress mirror: 100 l2 af l1 nc
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:11 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
11.1.0.1 00:00:01:00:00:01 Static
Ingress mirror: 100 l2 af l1 nc
---------------------------------------------
Subscriber user10 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.10 00:00:01:00:00:01 Static
Ingress mirror: 100 af ef h1 nc
---------------------------------------------
Subscriber user11 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.11 00:00:01:00:00:02 Static
Egress mirror: 100 l2 ef h1
---------------------------------------------
Subscriber user12 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.12 00:00:01:00:00:03 Static
Ingress mirror: 100 be l2 af l1 h2 ef h1 nc
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------
Subscriber user13 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.13 00:00:01:00:00:01 Static
Ingress mirror: 100 l1 ef h1
---------------------------------------------
Subscriber user14 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.14 00:00:01:00:00:02 Static
Egress mirror: 100 l2 h2 ef h1
---------------------------------------------
Subscriber user15 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.15 00:00:01:00:00:03 Static
Ingress mirror: 100 l1 nc
Egress mirror: 100 l1 nc
---------------------------------------------
Subscriber user16 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.16 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af nc
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:11 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
11.1.0.16 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af nc
---------------------------------------------
Subscriber user17 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla2
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.17 00:00:01:00:00:01 Static
Egress mirror: 100 af l1 h1
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:11 - sla:sla2
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
11.1.0.17 00:00:01:00:00:01 Static
Egress mirror: 100 af l1 h1
---------------------------------------------
Subscriber user18 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla3
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.18 00:00:01:00:00:01 Static
Ingress mirror: 100 h2
Egress mirror: 100 h2
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:11 - sla:sla3
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
11.1.0.18 00:00:01:00:00:01 Static
Ingress mirror: 100 h2
Egress mirror: 100 h2
---------------------------------------------
Subscriber user2 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.2 00:00:01:00:00:01 Static
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:11 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
11.1.0.2 00:00:01:00:00:01 Static
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------
Subscriber user3 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.3 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af l1 h2 ef h1 nc
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:11 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
11.1.0.3 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af l1 h2 ef h1 nc
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------
Subscriber user4 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.4 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------
Subscriber user5 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.5 00:00:01:00:00:01 Static
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------
Subscriber user6 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.6 00:00:01:00:00:01 Static
Ingress mirror: 100 be af l1 h2
Egress mirror: 100 be af l1 h2
---------------------------------------------
Subscriber user7 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.7 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af l1 h2 ef h1 nc
---------------------------------------------
Subscriber user8 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.8 00:00:01:00:00:01 Static
Egress mirror: 100 be af l1 h1 nc
---------------------------------------------
Subscriber user9 (sub1)
---------------------------------------------------------------------------
SLA Profile Instance sap:lag-8:1 - sla:sla1
---------------------------------------------------------------------------
IP Address MAC Address Origin
---------------------------------------------
1.1.0.9 00:00:01:00:00:01 Static
Ingress mirror: 100 be l2 af l1 h2 ef h1 nc
Egress mirror: 100 be l2 af l1 h2 ef h1 nc
===============================================================================
*A:EsrC#
*B:Dut-C# show service active-subscribers detail
===============================================================================
Active Subscribers
===============================================================================
-------------------------------------------------------------------------------
Subscriber basic1
(sub__S1)
-------------------------------------------------------------------------------
I. Sched. Policy : N/A
E. Sched. Policy : HSch1 E. Agg Rate Limit: Max
E. Min Resv Bw : 1
I. Policer Ctrl. : N/A
E. Policer Ctrl. : N/A
I. vport-hashing : Disabled
I. sec-sh-hashing: Disabled
Q Frame-Based Ac*: Disabled
Acct. Policy : N/A Collect Stats : Disabled
ANCP Pol. : N/A
Accu-stats-pol : (Not Specified)
HostTrk Pol. : N/A
IGMP Policy : igmp1
MLD Policy : mld1
PIM Policy : N/A
Sub. MCAC Policy : N/A
NAT Policy : N/A
Firewall Policy : N/A
UPnP Policy : N/A
NAT Prefix List : N/A
Allow NAT bypass : No
NAT access mode : auto
Def. Encap Offset: none Encap Offset Mode: none
Vol stats type : full
Preference : 5
LAG hash class : 1
LAG hash weight : 1
Sub. ANCP-String : "basic1"
Sub. Int Dest Id : ""
Igmp Rate Adj : N/A
RADIUS Rate-Limit: N/A
Oper-Rate-Limit : Maximum
-------------------------------------------------------------------------------
Radius Accounting
-------------------------------------------------------------------------------
Policy : radacct
Session Opti.Stop: False
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
(1) SLA Profile Instance
- sap:1/1/2:51 (VPRN 10 - gi-1-6)
- sla:slaS2S1
-------------------------------------------------------------------------------
Description : SLA Profile Id slaS2S1
Control plane(s) : local
Host Limits : No Limit
Session Limits : No Limit
Egr Sched-Policy : N/A
Ingress Qos-Policy : 11 Egress Qos-Policy : 110
Ingress Queuing Type : Service-queuing (Not Applicable to Policer)
Ingr IP Fltr-Id : N/A Egr IP Fltr-Id : N/A
Ingr IPv6 Fltr-Id : N/A Egr IPv6 Fltr-Id : N/A
Ingress Report-Rate : Maximum
Egress Report-Rate : Maximum
Egress Remarking : from Sap Qos
Credit Control Pol. : N/A
Category Map : (Not Specified)
Use ing L2TP DSCP : false
Default SPI sharing : per-sap
Hs-Agg-Rate-Limit : Maximum
Egress HS Q stat mode: no-override
Bonding Rate-thresh. : high 90 low 80
Bonding Weight : weight 100 5
Hs-Oper-Rate-Limit : Maximum
Egr hqos mgmt status : disabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
3fe0:0:0:10::/64
10:00:00:00:01:10 N/A DHCP6 10 Y
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLA Profile Instance statistics
-------------------------------------------------------------------------------
Packets Octets
Off. HiPrio : 0 0
Off. LowPrio : 5 670
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats (Ingress QoS Policy 11)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 5 670
Queueing Stats (Egress QoS Policy 110)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 5 670
-------------------------------------------------------------------------------
SLA Profile Instance per Queue statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 2 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 3 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 4 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 5 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 6 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 7 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 8 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 9 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 5 670
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 5 670
Egress Queue 1
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 2
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 3
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 5 670
Egress Queue 4
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 5
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 6
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 7
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 8
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
(2) SLA Profile Instance
- sap:1/1/2:113 (VPRN 10 - gi-1-11)
- sla:sla17S1 PPP session:23
-------------------------------------------------------------------------------
Description : SLA Profile Id sla17S1
Control plane(s) : local
Host Limits : No Limit
Session Limits : No Limit
Egr Sched-Policy : N/A
Ingress Qos-Policy : 17 Egress Qos-Policy : 110
Ingress Queuing Type : Service-queuing (Not Applicable to Policer)
Ingr IP Fltr-Id : N/A Egr IP Fltr-Id : N/A
Ingr IPv6 Fltr-Id : N/A Egr IPv6 Fltr-Id : N/A
Ingress Report-Rate : Maximum
Egress Report-Rate : Maximum
Egress Remarking : from Sap Qos
Credit Control Pol. : ccpol
Category Map : (Not Specified)
Use ing L2TP DSCP : false
Default SPI sharing : per-session
Hs-Agg-Rate-Limit : Maximum
Egress HS Q stat mode: no-override
Bonding Rate-thresh. : high 90 low 80
Bonding Weight : weight 100 5
Hs-Oper-Rate-Limit : Maximum
Egr hqos mgmt status : disabled
-------------------------------------------------------------------------------
Credit Control Policy: ccpol
Category Map : catmap1
Diameter Session Gy : router.be;1624914238;80
CC Failure Handling : terminate
Number of categories
static : 1
gx-session : 0
gx-pcc : 0
Category Name : cat1
Ingress Queues : 1
Egress Queues : 1
Ingress Policers : (Not Specified)
Egress Policers : (Not Specified)
Credit Volume Used : 0 Credit Time Used : 213
Credit Volume Avail. : 0 Credit Time Avail. : 87
Credit Volume Thres. : 0 Credit Time Thres. : 0
Credit Expired : False Credit Negotiating : False
Out Of Credit Action : None Quota Holding Time : 0
Validity Time Used : 212 Validity Time Avail. : 988
HTTP Rdr URL Override: (Not Specified)
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
10.1.0.111
10:00:00:00:01:91 PPP 1 IPCP 10 Y
3fe1:0:0:11::/64
10:00:00:00:01:91 PPP 1 SLAAC 10 Y
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLA Profile Instance statistics
-------------------------------------------------------------------------------
Packets Octets
Off. HiPrio : 0 0
Off. LowPrio : 10 1320
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats (Ingress QoS Policy 17)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 10 1320
Queueing Stats (Egress QoS Policy 110)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 10 1320
-------------------------------------------------------------------------------
SLA Profile Instance per Queue statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 2 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 10 1320
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 10 1320
Ingress Queue 3 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 2
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 3
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 10 1320
Egress Queue 4
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 5
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 6
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 7
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Egress Queue 8
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Number of active subscribers : 1
===============================================================================
*B:Dut-C#
Active Subscriber Field Descriptions describes active subscriber output fields.
Field |
Description |
---|---|
Active Subscribers |
The active subscriber’s name |
IP Address |
The IP address of the active subscriber |
MAC Address |
The MAC address of the active subscriber |
Session |
The session type |
Origin |
The IPCP parameter |
Svc |
The service ID |
Fwd |
Option to forward |
Number of active subscribers |
The total number of active subscribers |
adi
adi
Syntax
adi [service service-id] [ interface ip-int-name] [address mcast-address] [source ip-address] [detail]
Context
[Tree] (show>video adi)
Full Context
show video adi
Description
This command displays ad insertion channel information.
Parameters
- service service-id
-
Displays information pertaining to the specified service ID.
- interface ip-int-name
-
Displays information pertaining to the specified interface.
- address mcast-address
-
Displays information pertaining to the specified multicast channel address.
- source ip-address
-
Displays information pertaining to the source IP address.
- detail
-
The output displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
adjacency
adjacency
Syntax
adjacency [detail]
Context
[Tree] (show>service>id>spb adjacency)
Full Context
show service id spb adjacency
Description
This command displays SPB adjacency information.
Parameters
- detail
-
Shows detailed information
Platforms
All
Output
The following output is an example of service SPB adjacency information.
Output Example===============================================================================
ISIS Adjacency
===============================================================================
System ID Usage State Hold Interface MT Enab
-------------------------------------------------------------------------------
Dut-B L1 Up 19 sap:1/2/2:1.1 No
Dut-C L1 Up 21 sap:1/2/3:1.1 No
-------------------------------------------------------------------------------
Adjacencies : 2
===============================================================================
adjacency
Syntax
adjacency [ip-address | ip-int-name | nbr-system-id] [detail]
Context
[Tree] (show>router>isis adjacency)
Full Context
show router isis adjacency
Description
This command displays information regarding IS-IS neighbors. When no ip-address, ip-int-name, or nbr-system-id is specified, then all adjacencies are displayed.
Parameters
- ip-address
-
When specified, only adjacencies with that interface is displayed.
- ip-int-name
-
When specified, only adjacencies with that interface is displayed.
- nbr-system-id
-
When specified, only the adjacency with that ID is displayed.
- detail
-
All output is displayed in the detailed format.
- mt-id-number
-
Specifies the multi topology ID number for this route.
Platforms
All
Output
Standard and Detailed IS-IS Adjacency Output
Standard and Detailed Adjacency Output Fields describes the standard and detailed command output fields for an IS-IS adjacency.
Label |
Description |
---|---|
Interface |
Interface name associated with the neighbor. |
System-id |
Neighbor’s system ID. |
Level |
1-L1 only, 2-L2 only, 3-L1 and L2. |
State |
Up, down, new, one-way, initializing, or rejected. |
Hold |
Hold time remaining for the adjacency. |
SNPA |
Subnetwork point of attachment, MAC address of the next hop. |
Circuit type |
Level on the interface L1, L2, or both. |
Expires In |
Number of seconds until adjacency expires. |
Priority |
Priority to become designated router. |
Up/down transitions |
Number of times neighbor state has changed. |
Event |
Event causing last transition. |
Last transition |
Time since last transition change. |
Speaks |
Supported protocols (only IP). |
IP address |
IP address of neighbor. |
MT enab |
Yes — The neighbor is advertising at least 1 non MTID#0. |
Topology |
Derived from the MT TLV in the IIH
Not supported MTIDs => Topology line suppressed |
*A:Dut-C# show router isis adjacency
===============================================================================
Rtr Base ISIS Instance 0 Adjacency
===============================================================================
System ID Usage State Hold Interface MT-ID
-------------------------------------------------------------------------------
Dut-B L1L2 Up 23 to_Dut-B 0
Dut-D L1L2 Up 23 to_Dut-D1 0
-------------------------------------------------------------------------------
Adjacencies : 2
===============================================================================
*A:Dut-C# show router isis adjacency Dut-D detail
===============================================================================
Rtr Base ISIS Instance 0 Adjacency (detail)
===============================================================================
SystemID : Dut-D SNPA : 00:00:00:00:00:04
Interface : to_Dut-D1 Up Time : 0d 00:05:23
State : Up Priority : 0
Nbr Sys Typ : L1L2 L. Circ Typ : L1L2
Hold Time : 19 Max Hold : 27
Adj Level : L1L2 MT Enabled : No
Topology : Unicast
IPv6 Neighbor : fe80::200:ff:fe00:4
IPv4 Neighbor : 1.3.4.4
IPv4 Adj SID : Label 262139
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Suppressed : Disabled
Number of Restarts: 0
Last Restart at : Never
===============================================================================
*A:Dut-C#
*A:ALA-A# show router isis adjacency 180.0.7.12
===============================================================================
Rtr Base ISIS Instance 0 Adjacency
===============================================================================
System ID Usage State Hold Interface
-------------------------------------------------------------------------------
asbr_east L2 Up 25 if2/5
-------------------------------------------------------------------------------
Adjacencies : 1
===============================================================================
*A:ALA-A#
*A:ALA-A# show router isis adjacency if2/5
===============================================================================
Rtr Base ISIS Instance 0 Adjacency
===============================================================================
System ID Usage State Hold Interface
-------------------------------------------------------------------------------
asbr_east L2 Up 20 if2/5
-------------------------------------------------------------------------------
Adjacencies : 1
===============================================================================
*A:ALA-A#
*A:Dut-A# show router isis adjacency detail
===============================================================================
Rtr Base ISIS Instance 0 Adjacency (detail)
===============================================================================
SystemID : Dut-B SNPA : 20:81:01:01:00:01
Interface : ip-3FFE::A0A:101 Up Time : 0d 00:56:10
State : Up Priority : 64
Nbr Sys Typ : L1 L. Circ Typ : L1
Hold Time : 2 Max Hold : 2
Adj Level : L1 MT Enabled : Yes
Topology : Unicast, IPv6-Unicast
IPv6 Neighbor : FE80::2281:1FF:FE01:1
IPv4 Neighbor : 10.10.1.2
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Supressed : Disabled
Number of Restarts: 0
Last Restart at : Never
SystemID : Dut-B SNPA : 20:81:01:01:00:01
Interface : ip-3FFE::A0A:101 Up Time : 0d 00:56:10
State : Up Priority : 64
Nbr Sys Typ : L2 L. Circ Typ : L2
Hold Time : 2 Max Hold : 2
Adj Level : L2 MT Enabled : Yes
Topology : Unicast, IPv6-Unicast
IPv6 Neighbor : FE80::2281:1FF:FE01:1
IPv4 Neighbor : 10.10.1.2
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Supressed : Disabled
Number of Restarts: 0
Last Restart at : Never
SystemID : Dut-F SNPA : 00:00:00:00:00:00
Interface : ies-1-3FFE::A0A:1501 Up Time : 0d 01:18:34
State : Up Priority : 0
Nbr Sys Typ : L1L2 L. Circ Typ : L1L2
Hold Time : 5 Max Hold : 6
Adj Level : L1L2 MT Enabled : Yes
Topology : Unicast, IPv6-Unicast
IPv6 Neighbor : FE80::2285:FFFF:FE00:0
IPv4 Neighbor : 10.10.21.6
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Supressed : Disabled
Number of Restarts: 0
Last Restart at : Never
===============================================================================
*A:Dut-A#
adjacency
Syntax
adjacency [system-id]
Context
[Tree] (clear>router>isis adjacency)
Full Context
clear router isis adjacency
Description
This command clears and resets the entries from the IS-IS adjacency database.
Parameters
- system-id
-
When the system ID is entered, only the specified entries are removed from the IS-IS adjacency database.
Platforms
All
adjacency
Syntax
adjacency [system-id]
Context
[Tree] (clear>service>id>spb adjacency)
Full Context
clear service id spb adjacency
Description
This command clears and resets IS-IS adjacencies.
Parameters
- system-id
-
Specifies the system ID. When the system ID is entered, only the specified entries are removed from the IS-IS adjacency database.
Platforms
All
adjust-autobandwidth
adjust-autobandwidth
Syntax
adjust-autobandwidth [lsp lsp-name [force [ bandwidth mbps]]]
Context
[Tree] (tools>perform>router>mpls adjust-autobandwidth)
Full Context
tools perform router mpls adjust-autobandwidth
Description
This command initiates an immediate automatic bandwidth adjustment attempt for either one specific LSP or all active LSPs. The automatic bandwidth adjustment is made to the primary or secondary path of the LSP, whichever is the currently active path. If an LSP is not specified, then the system assumes the command applies to all LSPs. The optional force parameter, which is available only when an LSP is referenced, determines whether adjust-up and adjust-down threshold checks are applied. If force is not specified then the maximum average data rate must differ from the current reservation by more than the adjust-up or adjust-down thresholds, otherwise no bandwidth adjustment occurs. If the force option is specified then, bandwidth adjustment ignores the configured thresholds. If a bandwidth is specified as part of the force option then the bandwidth of the LSP is changed to this specific value, otherwise the bandwidth is changed to the maximum average data rate that has been measured by the system in the current adjust interval.
The adjust-count and maximum average data rate are not reset by the manual auto-bandwidth command, whether or not the bandwidth adjustment succeeds or fails. The overflow count is reset only if the manual auto-bandwidth attempt is successful.
Parameters
- lsp-name
-
Specifies the LSP name, up to 64 characters, to which this command applies. If this parameter is not supplied the command applies to all active LSPs.
- mbps
-
Specifies the bandwidth that the LSP should be immediately resized to.
Platforms
All
admin
admin
Syntax
admin
Context
[Tree] (show>app-assure>group>policy admin)
Full Context
show application-assurance group policy admin
Description
This command displays the application-assurance policy uncommitted changes.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the admin command.
Output Example*A:ALA-48>show>app-assure>group>policy# admin
begin
app-filter
entry 10 create
shutdown
exit
exit
app-qos-policy
entry 10 create
shutdown
exit
exit
commit
*A:ALA-48>show>app-assure>group>policy#
admin-group
admin-group
Syntax
admin-group [name]
Context
[Tree] (show>router>if-attribute admin-group)
Full Context
show router if-attribute admin-group
Description
This command displays administrative group statistics.
Parameters
- name
-
Displays entries that are associated with the specified administrative group name, up to 32 characters.
Platforms
All
Output
The following output is an example of administrative group statistics, and Administrative Group Fields describes the fields.
Output Example*A:node-3# show router if-attribute admin-group
==================================================
Interface Administrative Groups
==================================================
Group Name Group Value
--------------------------------------------------
Admin 4
admin 1
--------------------------------------------------
No. of Groups: 2
==================================================
*A:node-3#
Label |
Description |
---|---|
Group Name |
The name of the administrative group |
Group Value |
The integer value of the administrative group |
No. of Groups |
The total number of displayed administrative groups |
admin-lock
admin-lock
Syntax
admin-lock
Context
[Tree] (tools>perform>service>id admin-lock)
Full Context
tools perform service id admin-lock
Description
Commands in this context apply an administrative lock for a spoke SDP that is bound to a VLL SAP, another spoke-\ sdp or a VPLS interface for an MPLS-TP PW. After the PW is locked, it can be put into loopback mode. The command must be executed at both ends of the PW or MS-PW represented by the spoke-\ SDP. Test traffic can then be injected using a test SAP.
Platforms
All
admit-deny-stats
admit-deny-stats
Syntax
admit-deny-stats
Context
[Tree] (tools>dump>app-assure>group admit-deny-stats)
Full Context
tools dump application-assurance group admit-deny-stats
Description
This command displays application-assurance admit-deny statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of AA admit-deny statistics information.
Output Exampletools dump application-assurance group 1 admit-deny-stats
===================================================================================
Application-Assurance Group 1 Admit-Deny Statistics
===================================================================================
-----------------------------------------------------------------------------------
Packet Validation Statistics
Admitted Sub-To-Net Denied Sub-To-Net Admitted Net-To-Sub Denied Net-To-Sub
(Packets) (Packets) (Packets) (Packets)
-----------------------------------------------------------------------------------
Error
0 0 0 0
Fragments: Out-Of-Order
0 0 0 0
Fragments: All
0 0 0 0
Overload
N/A 0 N/A 0
-----------------------------------------------------------------------------------
TCP Validation Statistics
Admitted Sub-To-Net Denied Sub-To-Net Admitted Net-To-Sub Denied Net-To-Sub
(Packets) (Packets) (Packets) (Packets)
-----------------------------------------------------------------------------------
2 0 0 0 0
net 14 1 15 1
-----------------------------------------------------------------------------------
adv-config-policy
adv-config-policy
Syntax
adv-config-policy [policy-name] [association]
Context
[Tree] (show>qos adv-config-policy)
Full Context
show qos adv-config-policy
Description
This command displays advanced QoS policy information.
Parameters
- policy-name
-
The name of the advanced QoS policy.
- association
-
Displays associations related to the specified adv-config-policy.
Platforms
All
Output
The following output is an example of advanced QoS policy information, and Show QoS Scheduler-Hierarchy Customer Output Fields describes the advanced QoS policy fields.
Output Example*A:PE# show qos adv-config-policy "adv1"
===============================================================================
QoS Advanced Configure Policy
===============================================================================
Policy Name : adv1
Description : (Not Specified)
OM Add PIR Prcnt : 0.00 OM Add Rate : 0
OM Add [min-only : false] [active-min-only : false]
OM Gran PIR Prcnt : 0.00 OM Gran Rate : 0
Max Dec PIR Prcnt : 100.00 Max Dec Rate : 0
Abv Off PIR Prcnt : 100.00 Abv Off Rate : max
BWD Gran PIR Prcnt : 0.00 BWD Gran Rate : 0
Fast Start : Disabled Fast Stop : Disabled
Time Average Factor : 0 [dec-only : false]
Hi Rate Hold Time : 0 [active-min-only : false]
Sample Interval : 1 Enqueue on PIR Zero : false
Limit PIR Zero Drain : false Init LUB with min PIR : false
Internal Sched Wght Mode: no-override
Unconsumed Agg-rate : 100.00 Delta Consumed Agg-rate : 20.00
Unconsumed Hi-tier-rate : 100.00 Delta Consumed Hi-tier-rate : 5.00
===============================================================================
*APE#
Label |
Description |
---|---|
Policy Name |
Displays the policy name. |
Description |
Displays the policy description. |
OM Add PIR Prcnt |
Displays the percentage of the administrative PIR by which the measured rate is increased. |
OM Add Rate |
Displays the amount, in kb/s, by which the measured rate is increased. |
OM Add |
min-only — When this option is true, the system uses the specified increase as a minimum offered rate even for inactive queues or policers associated with the policy. active-min-only — When this option is true, the respective rate or percentage is treated as the minimum offered rate for a queue only when the queue has an actual non-zero offered rate. This is intended to limit the artificial increase in offered rate to queues that are currently active. When a queue’s measured offered rate drops to zero, the system stops enforcing the minimum value. |
OM Gran PIR Prcnt |
Displays the percentage of the child’s administrative PIR that is used as the threshold sensitivity to the offered rate change. If a value of 0 or 0.00 is used, the system will interpret this equivalent to no granularity. |
OM Gran Rate |
Displays the explicit rate, in kb/s, that are used as the child’s offered rate change sensitivity value. If a rate sensitivity of 0 is specified, the system interprets this equivalent to no granularity. |
Max Dec PIR Prcnt |
Displays the percentage of the child’s administrative PIR that is used as the decrement limit to the offered rate change. If a value of 100 or 100.00 is used, the system interprets this equivalent as no max-decrement. |
Max Dec Rate |
Displays the rate, in kb/s, that is used as the child’s offered rate change sensitivity value. If a rate sensitivity of 0 is specified, the system interprets this equivalent to no granularity. |
Abv Off PIR Prcnt |
Displays the percentage of the child’s administrative PIR that is used as the fair share increase limit. The new operational PIR result is capped by the child’s PIR. If a value of 0 or 0.00 is specified, the system will disable the fair share increase function and only configure the actual distribution rate. If a value of 100 or 100.00 is used, the system will interpret this equivalent to executing the no above-offered-cap command and return the fair-share operation to the default behavior. |
Abv Off Rate |
Specifies the explicit rate, in kb/s, that is used as the limit to the child’s fair share increase to the operational PIR. The new operational PIR result is capped by the child’s PIR. If a value of 0 is used, the system will disable the fair share increase function and only configure the actual distribution rate. |
BWD Gran PIR Prcnt |
Displays the percentage of the child’s administrative PIR that is used as the rounding step value. If a value of 0 or 0.00 is used, the system will interpret this equivalent to no granularity. |
BWD Gran Rate |
Displays the rate, in kb/s, that is used as the rounding step value. If a value of 0 is used, the system will interpret this equivalent to no granularity. |
Fast Start |
Displays whether fast detection of initial bandwidth on a child policer or queue associated with the policy is enabled. |
Fast Stop |
Displays whether fast detection of lack of offered rate on a child policer or queue associated with the policy is enabled. |
Time Average Factor |
Displays the time average factor used to calculate the weight of the new offered rate using a portion of the previous offered rate. If dec-only is true, the time average factor adjustment is only applied if the new offered rate is decreasing compared to the previous offered rate. |
Hi Rate Hold Time |
Displays the time period that the current offered rate is maintained for a child policer or queue when it is seen that the offered rate is decreasing. The offered measurement that triggers the hold time is used when the hold timer expires, unless a higher offered rate is seen in the interim. When a higher rate is observed, the hold timer is canceled and the higher offered rate is used immediately. If active-min-only is true, the respective rate or percentage is treated as the minimum offered rate for a queue, only when the queue has an actual non-zero offered rate. |
Sample Interval |
Displays the number of intervening sample periods before a new offered rate is measured. |
Enqueue on PIR Zero |
Displays whether enqueue-on-pir-zero is enabled. If it is enabled, when the operational PIR is set to zero, the queue’s MBS remains set to the normal value and is not also set to zero. |
Limit PIR Zero Drain |
If true, the system to use the minimum configurable PIR instead of an H-QoS derived zero operational PIR. |
Init LUB with min PIR |
If true, new queues associated with a LUB context are assigned a minimum rate operational PIR to be applied to the queue for use by enqueued packets prior to an H-QoS iteration. |
Internal Sched Wght Mode |
Specifies the internal scheduler weight: default — Specifies that queues are equally weighted, except at ingress for mixed-speed LAGs without per-fp-inq-queuing enabled and at egress for all mixed-speed LAGs, in which cases the queues are weighted based on port speed. force-equal — Specifies that the queues are always equally weighted. offered-load — Specifies that the queues are weighted based on observed offered load. capped-offered-load — Specifies that the queues are weighted based on observed offered load capped by PIR. |
Unconsumed Agg-rate |
Displays the percentage of the unconsumed aggregate rate that can be given to a queue at the end of an H-QoS pass. |
Delta Consumed Agg-rate |
Displays the percentage of the delta consumed aggregate rate that can be given to a queue at the end of an H-QoS pass. |
Unconsumed Hi-tier-rate |
Displays the percentage of the unconsumed higher tier rate that can be given to a queue at the end of an H-QoS pass. |
Delta Consumed Hi-tier-rate |
Displays the percentage of the delta consumed higher tier rate that can be given to a queue at the end of an H-QoS pass. |
agg-rate
agg-rate
Syntax
agg-rate
Context
[Tree] (show>qos agg-rate)
Full Context
show qos agg-rate
Description
This command displays aggregate rate information.
Platforms
All
aggregate
aggregate
Syntax
aggregate [family] [active] [ detail]
Context
[Tree] (show>router aggregate)
Full Context
show router aggregate
Description
This command displays aggregated routes.
Parameters
- active
-
This keyword filters out inactive aggregates.
- detail
-
This keyword displays detailed information.
- family
-
Specifies the family to display.
Platforms
All
Output
The following output is an example of router aggregate information, and Show Aggregate Field Descriptions describes the output fields.
Output Example*A:ALA-12# show router 3 aggregate
==============================================================================
Aggregates (Service: 3)
==============================================================================
Prefix Summary AS Set Aggr AS Aggr IP-Address State
------------------------------------------------------------------------------
------------------------------------------------------------------------------
No. of Aggregates: 0
-----------------------------------------------------------
*A:ALA-12#
*A:Dut-A>config>router# show router aggregate
===============================================================================
Aggregates (Router: Base)
===============================================================================
Prefix Aggr IP-Address Aggr AS
Summary AS Set State
NextHop NextHopType
-------------------------------------------------------------------------------
10.2.3.0/24 0.0.0.0 0
False False Inactive
10.2.2.2 Indirect
10.2.0.0/16 0.0.0.0 0
False False Active
None
-------------------------------------------------------------------------------
No. of Aggregates: 2
===============================================================================
*A:CPM133>config>router# show router aggregate
===============================================================================
Aggregates (Router: Base)
===============================================================================
Prefix Aggr IP-Address Aggr AS
Summary AS Set State
NextHop Community NextHopType
-------------------------------------------------------------------------------
10.0.0.0/8 0.0.0.0 0
False False Inactive
100:33 Blackhole
-------------------------------------------------------------------------------
No. of Aggregates: 1
===============================================================================
Label |
Description |
---|---|
Prefix |
Displays the destination address of the aggregate route in dotted decimal notation. |
Summary |
Specifies whether the aggregate or more specific components are advertised. |
AS Set |
Displays an aggregate where the path advertised for the route consists of all elements contained in all paths that are being summarized. |
Aggr AS |
Displays the aggregator path attribute to the aggregate route. |
Aggr IP-Address |
The IP address of the aggregated route. |
State |
The operational state of the aggregated route. |
No. of Aggregates |
The total number of aggregated routes. |
alarm-contact-input
alarm-contact-input
Syntax
alarm-contact-input {alarm-contact-input-id | all} [detail]
Context
[Tree] (show>system alarm-contact-input)
Full Context
show system alarm-contact-input
Description
This command displays the alarm contact input information.
Parameters
- alarm-contact-input-id
-
Specifies the alarm contact input pin number. Alarm contact input information is displayed only for the specified pin.
- all
-
Displays alarm contact input information for all pins.
- detail
-
Displays detailed alarm contact input information for the specifies pin or all pins.
Platforms
7750 SR-a
Output
The following output is an example of alarm contact input information, and Alarm Contact Input Field Descriptions describes the output fields.
Output Example============================================================
Alarm Contact Input
============================================================
Alarm Input Pin Number : 1
Description : (Not Specified)
Alarm Input Pin Current State : Disabled
Alarm Severity : major
Alarm Raised : No
Last State Change : 03/18/2021 14:45:31
Alarm Input Pin Number : 2
Description : (Not Specified)
Alarm Input Pin Current State : Disabled
Alarm Severity : major
Alarm Raised : No
Last State Change : 02/21/2021 11:46:45
Alarm Input Pin Number : 3
Description : (Not Specified)
Alarm Input Pin Current State : Disabled
Alarm Severity : major
Alarm Raised : No
Last State Change : 02/22/2021 16:20:00
Alarm Input Pin Number : 4
Description : (Not Specified)
Alarm Input Pin Current State : Disabled
Alarm Severity : major
Alarm Raised : No
Last State Change : 03/18/2021 14:45:31
Label |
Description |
---|---|
Alarm Input Pin Number |
Indicates the alarm contact input pin number. |
Description |
Displays the configured description string for the alarm contact input |
Alarm Input Pin Current State |
Indicates the configured administrative state of the alarm contact input. Disabled — The alarm contact input is disabled (shutdown) and log events will not be generated for changes to the input pin status. Enabled — The alarm contact input is enabled (no shutdown) and log events are generated for changes to the input pin status as long as the log events are not suppressed in event-control configuration. |
Alarm Severity |
Indicates the configured severity of the associated CHASSIS log event. |
Alarm Raised |
Indicates if the input pin is triggered or not. |
Last State Change |
Indicates when the input pin last changed state. |
alarms
alarms
Syntax
alarms [cleared] [count count] [newer-than days] [severity severity-level]
Context
[Tree] (show>system alarms)
Full Context
show system alarms
Description
This command displays facility alarms on the system. Alarm support covers a focused subset of router states that are likely to indicate service impacts (or imminent service impacts) related to the overall state of hardware assemblies (cards, fans, links, and so on).
Platforms
All
Output
Show Facility Alarms Output Fields describes the alarms output fields.
Use the following command to display facility alarms on the system.
show system alarms
Output
Example
===============================================================================
Alarms [Critical:1 Major:2 Minor:0 Warning:0 Total:3]
===============================================================================
Index Date/Time Severity Alarm Resource
Details
-------------------------------------------------------------------------------
8 2011/04/01 18:36:43.80 MAJOR 7-2011-1 Power Supply 1
Power supply 1, power lost
7 2011/04/01 18:35:57.00 MAJOR 7-2005-1 Chassis 1
Chassis 1: temperature too high
6 2011/04/01 18:35:24.80 CRITICAL 7-2006-1 Fan 1
Fan 1 failed
===============================================================================
Output Example
(ESA)===============================================================================
Alarms [Critical:3 Major:1 Minor:0 Warning:0 Total:4]
===============================================================================
Index Date/Time Severity Alarm Resource
Details
-------------------------------------------------------------------------------
8 2022/08/23 17:06:54.70 MAJOR 7-2426-1 Chassis esa-1
ESA Chassis temperature status degraded
7 2022/08/23 17:06:54.70 CRITICAL 7-2416-1 Chassis esa-1
ESA Chassis fan status degraded
6 2022/08/23 17:06:14.70 CRITICAL 7-2410-1 Chassis esa-1
ESA Chassis power supply 2 status failed
5 2022/08/23 17:06:14.70 CRITICAL 7-2404-1 Chassis esa-1
ESA Chassis power supply 1 status degraded
===============================================================================
Use the following command to display cleared facility alarms on the system.
show system alarms cleared
Output
Example
===============================================================================
Cleared Alarms [Size:500 Total:5 (not wrapped)]
===============================================================================
Index Date/Time Severity Alarm Resource
Details
-------------------------------------------------------------------------------
5 2011/04/01 18:11:55.00 MAJOR 7-2005-1 Chassis 1
Clear Chassis temperature too high alarm
3 2011/04/01 18:11:54.50 CRITICAL 7-2051-1 Power Supply 1
Clear Power Supply failure
2 2011/04/01 18:11:54.40 CRITICAL 7-2050-1 Power Supply 1
Clear Power Supply failure
4 2011/04/01 18:11:54.10 MINOR 7-2004-1 Fan 1
Clear Fan wrong type failure
1 2011/04/01 18:11:54.00 CRITICAL 7-2007-1 Power Supply 1
Clear Power Supply failure
===============================================================================
Output Example (ESA)
===============================================================================
Cleared Alarms [Size:500 Total:14 (not wrapped)]
===============================================================================
Index Date/Time Severity Alarm Resource
Details
-------------------------------------------------------------------------------
15 2022/09/22 14:49:36.00 MAJOR 7-2422-1 Chassis esa-1
ESA Chassis power supply redundancy degraded - cleared, now redundant
14 2022/09/22 14:49:36.00 MAJOR 7-2400-1 Chassis esa-1
ESA Chassis aggregate hardware degraded status cleared, now ok
13 2022/09/22 14:49:31.00 CRITICAL 7-2410-1 Chassis esa-1
ESA Chassis power supply 2 failed status cleared, now ok
12 2022/09/22 11:27:04.80 MAJOR 7-2400-1 Chassis esa-1
ESA Chassis aggregate hardware degraded status cleared, now ok
Label |
Description |
---|---|
Index |
Alarm index number |
Date/Time |
Date and time string for the alarm |
Severity |
Severity level of the alarm |
Alarm |
Alarm identifier |
Resource |
Facility associated with the alarm |
Details |
Description of the alarm |
ale-adjust
ale-adjust
Syntax
ale-adjust
ale-adjust subscriber sub-ident-string
Context
[Tree] (show>service>active-subscribers ale-adjust)
Full Context
show service active-subscribers ale-adjust
Description
This command displays subscriber Access Loop Encapsulation adjust information.
Parameters
- sub-ident-string
-
Displays subscriber Access Loop Encapsulation adjust for the specified subscriber, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
alias
alias
Syntax
alias
Context
[Tree] (show alias)
Full Context
show alias
Description
This command shows command aliases.
This command is not available in the MD-CLI. Use the MD-CLI info detail environment command-alias command.
Platforms
All
Output
The following output is an example of alias information, and Show Alias Output Fields describes the output fields.
Output ExampleA:ALA-103>config>system# show alias
==============================================================================
Alias-Name Alias-command-name
==============================================================================
sri show router interface
sse show service service-using epipe
ssvpls show service service-using vpls
ssvprn show service service-using vprn
ssi show service service-using ies
------------------------------------------------------------------------------
Number of aliases : 5
==============================================================================
A:ALA-103>config>system#
Label |
Description |
---|---|
Alias-Name |
Displays the name of the alias. |
Alias-command-name |
The command and parameter syntax that define the alias. |
Number of aliases |
The total number of aliases configured on the router. |
all
all
Syntax
all
Context
[Tree] (show>service>id all)
Full Context
show service id all
Description
This command displays all information about the service.
Platforms
All
Output
Show All Service-ID Output
Output Example*A:PE-6# show service id 1 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : VPLS
Name : 1
Description : (Not Specified)
Customer Id : 1 Creation Origin : manual
Last Status Change: 05/08/2018 09:40:32
Last Mgmt Change : 05/08/2018 09:40:24
Etree Mode : Disabled
Admin State : Up Oper State : Up
MTU : 1514
SAP Count : 1 SDP Bind Count : 1
Snd Flush on Fail : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Propagate MacFlush: Disabled Per Svc Hashing : Disabled
Allow IP Intf Bind: Disabled
Fwd-IPv4-Mcast-To*: Disabled Fwd-IPv6-Mcast-To*: Disabled
Mcast IPv6 scope : mac-based
Def. Gateway IP : None
Def. Gateway MAC : None
Evpn Mcast GW : Enabled Mcast-GW Type : MEG
Temp Flood Time : Disabled Temp Flood : Inactive
Temp Flood Chg Cnt: 0
SPI load-balance : Disabled
TEID load-balance : Disabled
Src Tep IP : N/A
Vxlan ECMP : Disabled
-------------------------------------------------------------------------------
BGP Information
-------------------------------------------------------------------------------
Split Horizon Group specifics
-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults : ignore
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Sdp Id 65:1 -(192.0.2.5)
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 65:1 Type : Spoke
Spoke Descr : (Not Specified)
Split Horiz Grp : (Not Specified)
Etree Root Leaf Tag: Disabled Etree Leaf AC : Disabled
VC Type : Ether VC Tag : n/a
Admin Path MTU : 0 Oper Path MTU : 8974
Delivery : MPLS
Far End : 192.0.2.5 Tunnel Far End :
Oper Tunnel Far End: 192.0.2.5
LSP Types : LDP
Hash Label : Disabled Hash Lbl Sig Cap : Disabled
Oper Hash Label : Disabled
Entropy Label : Disabled
Admin State : Up Oper State : Down
MinReqd SdpOperMTU : 1514
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 524279 Egress Label : None
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
BFD Template : None
BFD-Enabled : no BFD-Encap : ipv4
Last Status Change : 05/07/2018 16:50:10 Signaling : TLDP
Last Mgmt Change : 05/08/2018 09:40:24
Endpoint : N/A Precedence : 4
PW Status Sig : Enabled
Force Vlan-Vc : Disabled Force Qinq-Vc : none
Class Fwding State : Down
Flags : NoEgrVCLabel
Time to RetryReset : never Retries Left : 3
Mac Move : Blockable Blockable Level : Tertiary
Local Pw Bits : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : None
Peer Vccv CC Bits : None
Application Profile: None
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
OAM MAC Addr : 0 DHCP MAC Addr : 0
Host MAC Addr : 0 Intf MAC Addr : 0
SPB MAC Addr : 0 Cond MAC Addr : 0
BGP EVPN Addr : 0 EVPN Static Addr : 0
MAC Learning : Enabled Discard Unkwn Srce: Disabled
MAC Aging : Enabled
BPDU Translation : Disabled
L2PT Termination : Disabled
MAC Pinning : Disabled
Ignore Standby Sig : False Block On Mesh Fail: False
Oper Group : (none) Monitor Oper Grp : (none)
Auto Learn Mac Prot: Disabled
RestMacProtSrc Act : none
Ingress Qos Policy : (none) Egress Qos Policy : (none)
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
Control Channel Status
-------------------------------------------------------------------------------
PW Status : disabled Refresh Timer : <none>
Peer Status Expire : false
Request Timer : <none>
Acknowledgement : false
MCAC Policy Name :
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
MCAC If-Policy Name:
-------------------------------------------------------------------------------
ETH-CFM SDP-Bind specifics
-------------------------------------------------------------------------------
V-MEP Filtering : Disabled
Squelch ch Levels : None
Squelch ch Ctag Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
LDP Information :
-------------------------------------------------------------------------------
LDP LSP Id : 65541
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn
Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : disabled
OSPF : disabled
TE-LSP : disabled
-------------------------------------------------------------------------------
Stp Service Destination Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Discarding
Port Number : 0 Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
Designated Bridge : N/A Designated Port Id: 0
Fwd Transitions : 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
SAP 1/1/c1/1:1
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/c1/1:1 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 05/07/2018 16:50:10
Last Mgmt Change : 05/08/2018 09:40:32
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Etree Root Leaf Tag: Disabled Etree Leaf Tag : 0
Etree Leaf AC : Disabled
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
OAM MAC Addr : 0 DHCP MAC Addr : 0
Host MAC Addr : 0 Intf MAC Addr : 0
SPB MAC Addr : 0 Cond MAC Addr : 0
BGP EVPN Addr : 0 EVPN Static Addr : 0
Admin MTU : 9000 Oper MTU : 9000
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
ARP Reply Agent : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Mac Learning : Enabled Discard Unkwn Srce: Disabled
Mac Aging : Enabled Mac Pinning : Disabled
BPDU Translation : Disabled
L2PT Termination : Disabled
Vlan-translation : None
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Cflowd : Disabled
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
MCAC Policy Name : MCAC Const Adm St : Enable
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
Use LAG port weight: no
MCAC If-Policy Name:
Restr MacUnpr Dst : Disabled
Auto Learn Mac Prot: Disabled
RestMacProtSrc Act : none
Time to RetryReset : never Retries Left : 3
Mac Move : Blockable Blockable Level : Tertiary
Auth Policy : None
DestMac Rewrite : Disabled
SendBvplsEvpnFlush : Enabled
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a V-MEP Filtering : Disabled
Squelch ch Levels : None
Squelch ch Ctag Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : N/A Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
CIST Desig Bridge : N/A Designated Port : N/A
Forward transitions: 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State : outOfService
Host Limit : 1 Min Auth Interval : 15 minutes
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
DHCP
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down Lease Populate : 0
DHCP Snooping : Down Action : Keep
Proxy Admin State : Down
Proxy Lease Time : N/A
Emul. Server Addr : Not Configured
-------------------------------------------------------------------------------
DHCP6
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down
DHCP Snooping : Down
Interface-Id : AsciiTuple Remote-Id : Disabled
-------------------------------------------------------------------------------
Subscriber Management
-------------------------------------------------------------------------------
Admin State : Down MAC DA Hashing : False
Def Sub-Id : None
Def Sub-Profile : None
Def SLA-Profile : None
Def Inter-Dest-Id : None
Sub-Ident-Policy : None
Subscriber Limit : 1
Single-Sub-Parameters
Prof Traffic Only : False
Non-Sub-Traffic : N/A
Static host management
MAC learn options : N/A
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : N/A
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 11 (Multipoint) (Priority)
Off. Combined : 0 0
Off. Managed : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state : Up Core Connectivity : Down
Stp Admin State : Down Stp Oper State : Down
Mode : Rstp Vcp Active Prot. : N/A
Bridge Id : 80:00.d8:4a:ff:00:00:00 Bridge Instance Id: 0
Bridge Priority : 32768 Tx Hold Count : 6
Topology Change : Inactive Bridge Hello Time : 2
Last Top. Change : 0d 00:00:00 Bridge Max Age : 20
Top. Change Count : 0 Bridge Fwd Delay : 15
MST region revision: 0 Bridge max hops : 20
MST region name :
Root Bridge : N/A
Primary Bridge : N/A
Root Path Cost : 0 Root Forward Delay: 0
Rcvd Hello Time : 0 Root Max Age : 0
Root Priority : 0 Root Port : N/A
-------------------------------------------------------------------------------
Forwarding Database specifics
-------------------------------------------------------------------------------
Service Id : 1 Mac Move : Disabled
Primary Factor : 3 Secondary Factor : 2
Mac Move Rate : 2 Mac Move Timeout : 10
Mac Move Retries : 3
Table Size : 250 Allocated Count : 0
Total In Use : 0
Learned Count : 0 Static Count : 0
OAM MAC Count : 0 DHCP MAC Count : 0
Host MAC Count : 0 Intf MAC Count : 0
Spb Count : 0 Cond MAC Count : 0
BGP EVPN Count : 0 EVPN Static Cnt : 0
EVPN Dup Det Cnt : 0
Remote Age : 900 Local Age : 300
High Watermark : 95% Low Watermark : 90%
Mac Learning : Enabled Discard Unknown : Disabled
Mac Aging : Enabled Relearn Only : False
Mac Subnet Len : 48
Sel Learned FDB : Disabled
-------------------------------------------------------------------------------
IGMP Snooping Base info
-------------------------------------------------------------------------------
Admin State : Down
Querier : No querier found
-------------------------------------------------------------------------------
Port Oper MRtr Pim Send Max Max Max MVR Num
Id Stat Port Port Qrys Grps Srcs Grp From-VPLS Grps
Srcs
-------------------------------------------------------------------------------
sap:1/1/c1/1:1 Up No No No None None None Local 0
sdp:65:1 Down No No No None None None N/A 0
-------------------------------------------------------------------------------
MLD Snooping Base info
-------------------------------------------------------------------------------
Admin State : Down
Querier : No querier found
-------------------------------------------------------------------------------
Port Oper MRtr Send Max Num MVR Num
Id State Port Queries Groups From-VPLS Groups
-------------------------------------------------------------------------------
sap:1/1/c1/1:1 Up No Disabled No Limit Local 0
sdp:65:1 Down No Disabled No Limit N/A 0
-------------------------------------------------------------------------------
DHCP Summary, service 1
-------------------------------------------------------------------------------
Sap/Sdp Snoop Used/ Arp Reply Info Admin
Provided Agent Option State
-------------------------------------------------------------------------------
sap:1/1/c1/1:1 No 0/0 No Keep Down
sdp:65:1 No N/A N/A N/A N/A
-------------------------------------------------------------------------------
Number of Entries : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
ARP host Summary, service 1
-------------------------------------------------------------------------------
Sap Used Provided Admin State
-------------------------------------------------------------------------------
sap:1/1/c1/1:1 0 1 outOfService
-------------------------------------------------------------------------------
Number of SAPs : 1 0
-------------------------------------------------------------------------------
===============================================================================
Service VPLS Group Information
===============================================================================
===============================================================================
No vxlan information for 1
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
-------------------------------------------------------------------------------
===============================================================================
VPLS Sites
===============================================================================
Site Site-Id Dest Mesh-SDP Admin Oper Fwdr
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
All Service-ID Field Descriptions describes the show all service-id command output fields:
Label |
Description |
---|---|
Service Id |
The value that identifies a service |
VPN Id |
The number that identifies the VPN |
Service Type |
The type of service |
SDP Id |
The SDP identifier |
Description |
The text string describing general information about the service |
Customer Id |
The customer identifier |
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer |
SAP Count |
The number of SAPs specified for this service |
SDP Bind Count |
The number of SDPs bound to this service |
Evpn Mcast GW |
The status of the EVPN multicast gateway |
Mcast-GW Type |
The multicast gateway type: MEG, PEG, or MEG-PEG |
Split Horizon Group |
The name of the split horizon group for this service |
Description |
The text string describing the split horizon group |
Last Changed |
The date and time of the most recent management-initiated change to this split horizon group |
SDP Id |
The SDP identifier |
Type |
The service SDP binding type, spoke or mesh |
Admin Path MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented |
Delivery |
The type of delivery used by the SDP: GRE or MPLS |
Admin State |
The administrative state of this SDP |
Oper State |
The operational status of the KeepAlive protocol. |
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP |
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP |
Ingress Filter |
The ID of the ingress filter policy |
Egress Filter |
The ID of the egress filter policy |
Far End |
The IP address of the remote end of the GRE or MPLS tunnel defined by this SDP |
Last Changed |
The date and time of the most recent change to this customer |
Signaling |
The signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
Admin State |
The operating status of the SDP |
Oper State |
The operational state of the SDP |
Hello Time |
The frequency that SDP echo request messages are transmitted on this SDP |
Hello Msg Len |
The length of the SDP echo request messages transmitted on this SDP |
Max Drop Count |
The maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault |
Hold Down Time |
The amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
SDP Delivery Mechanism |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the Far End field. If the SDP type is GRE, then the following message displays: SDP Delivery Mechanism is not MPLS |
Number of SDPs |
The total number SDPs applied to this service ID |
Service Access Points |
|
Service Id |
The value that identifies a service |
Port Id |
The ID of the access port where this SAP is defined |
Description |
The generic information about the SAP |
Encap Value |
The value of the label used to identify this SAP on the access port. |
Admin State |
The desired state of the SAP |
Oper State |
The operating state of the SAP |
Last Changed |
The date and time of the last change |
Admin MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented |
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented |
Ingress qos-policy |
The SAP ingress QoS policy ID |
Egress qos-policy |
The SAP egress QoS policy ID |
Ingress Filter-Id |
The SAP ingress filter policy ID |
Egress Filter-Id |
The SAP egress filter policy ID |
Multi Svc Site |
The multi-service site in which the SAP is a member |
Ingress sched-policy |
The ingress QoS scheduler for the SAP |
Egress sched-policy |
The egress QoS scheduler for the SAP |
Acct. Pol |
The accounting policy applied to the SAP |
Collect Stats |
Accounting statistics collected on the SAP |
Dropped |
The number of packets or octets dropped |
Offered Hi Priority |
The number of high priority packets, as determined by the SAP ingress QoS policy |
Offered Low Priority |
The number of low priority packets, as determined by the SAP ingress QoS policy |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded |
Dropped In Profile |
The number of in-profile packets or octets discarded |
Dropped Out Profile |
The number of out-of-profile packets or octets discarded |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded |
Ingress Queue 1 |
The index of the ingress QoS queue of this SAP |
High priority offered |
The packets or octets count of the high priority traffic for the SAP |
High priority dropped |
The number of high priority traffic packets or octets dropped |
Low priority offered |
The packets or octets count of the low priority traffic |
Low priority dropped |
The number of low priority traffic packets or octets dropped |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded |
Out profile forwarded |
The number of out-of-profile octets (rate above CIR) forwarded |
Egress Queue 1 |
The index of the egress QoS queue of the SAP |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded |
In profile dropped |
The number of in-profile packets or octets dropped for the SAP |
Out profile forwarded |
The number of out-of-profile packets or octets (rate above CIR) forwarded |
Out profile dropped |
The number of out-of-profile packets or octets discarded |
State |
The DHCP relay state on this SAP |
Info Option |
Option 82 processing state on this SAP |
Action |
Option 82 processing state SAP or interface: keep, replace or drop |
Circuit ID |
If index is inserted in Circuit ID sub-option of Option 82 |
Remote ID |
The far-end MAC address inserted in remote ID sub-option of Option 82 |
Managed by Service |
The service-id of the management VPLS managing this SAP |
Managed by SAP |
The SAP ID inside the management VPLS managing this SAP |
Prune state |
The STP state inherited from the management VPLS |
Managed by Service |
The service ID of the management VPLS managing this spoke SDP |
Managed by Spoke |
The SAP ID inside the management VPLS managing this spoke SDP |
Prune state |
The STP state inherited from the management VPLS |
all
Syntax
all
Context
[Tree] (show>service>id all)
Full Context
show service id all
Description
This command displays detailed information for all aspects of the service.
Platforms
All
Output
The following output is an example of all service ID information, and Show Service ID Output Fields describes the output fields.
Output Example*A:PE# show service id 1 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : Epipe
Name : 1
Description : (Not Specified)
Customer Id : 1 Creation Origin : manual
Last Status Change: 08/31/2018 11:12:04
Last Mgmt Change : 08/31/2018 11:09:25
Test Service : No
Admin State : Up Oper State : Up
MTU : 1514
Vc Switching : False
SAP Count : 2 SDP Bind Count : 0
Per Svc Hashing : Disabled
Vxlan Src Tep Ip : N/A
Force QTag Fwd : Disabled
Oper Group : <none>
-------------------------------------------------------------------------------
BGP Information
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults : ignore
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/1
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/1 Encap : null
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 11:12:04
Last Mgmt Change : 08/31/2018 11:09:24
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
LLF Admin State : Down LLF Oper State : Clear
Admin MTU : 1514 Oper MTU : 1514
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Endpoint : N/A
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
Vlan-translation : None
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Application Profile: None
Transit Policy : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Ignore Oper Down : Disabled
Lag Link Map Prof : (none)
Cflowd : Disabled
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : 08/31/2018 11:19:51
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
SAP 1/1/9:1
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/9:1 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 11:09:25
Last Mgmt Change : 08/31/2018 11:23:45
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Endpoint : N/A
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
Vlan-translation : None
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Application Profile: None
Transit Policy : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Ignore Oper Down : Disabled
Lag Link Map Prof : (none)
Cflowd : Disabled
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : 08/31/2018 11:19:51
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
-------------------------------------------------------------------------------
==========================================================================
VLL Sites
==========================================================================
Site Site-Id Dest Admin Oper Fwdr
--------------------------------------------------------------------------
No Matching Entries
==========================================================================
===============================================================================
*A:PE#
Show Service ID Output Fields describes the Show service ID output fields when the all option is specified.
Label |
Description |
---|---|
Service Id |
The service identifier |
VPN Id |
The number which identifies the VPN |
Service Type |
The type of service |
VLL Type |
The the VLL type |
SDP Id |
The SDP identifier for the 7450 ESS or 7750 SR |
Description |
Generic information about the service |
Customer Id |
The customer identifier |
Last Mgmt Change |
The date and time of the most recent management-initiated change |
Endpoint |
The name of the service endpoint for the 7450 ESS or 7750 SR |
Flags |
The conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch,RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, NoSapEpipeRingNode. |
SAP Count |
The number of SAPs specified for this service |
SDP Bind Count |
The number of SDPs bound to this service for the 7450 ESS or 7750 SR |
Split Horizon Group Specifics |
|
Split Horizon Group |
The name of the split horizon group for this VPLS for the 7450 ESS or 7750 SR |
Description |
The description of the split horizon group for the 7450 ESS or 7750 SR |
Last Changed |
The date and time of the most recent management-initiated change to this split horizon group for the 7450 ESS or 7750 SR |
Service Destination Points (SDPs) |
|
SDP Id |
The SDP identifier for the 7450 ESS or 7750 SR |
Type |
Indicates whether this service SDP binding is a spoke or a mesh for the 7450 ESS or 7750 SR |
Admin Path MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented for the 7450 ESS or 7750 SR. |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented for the 7450 ESS or 7750 SR |
Delivery |
The type of delivery used by the SDP: GRE or MPLS for the 7450 ESS or 7750 SR |
Admin State |
The administrative state of this SD for the 7450 ESS or 7750 SR |
Oper State |
The operational state of this SDP for the 7450 ESS or 7750 SR |
Jitter Buffer (packets) |
The jitter buffer length in number of packet buffers for the 7450 ESS or 7750 SR |
Playout Threshold (packets) |
The playout buffer packets threshold in number of packet buffers for the 7450 ESS or 7750 SR |
Playout Threshold (packets) |
Indicates the current packet depth of the jitter buffer for the 7450 ESS or 7750 SR |
Peer Pw Bits |
The bits set by the LDP peer when there is a fault on its side of the pseudowire for the 7450 ESS or 7750 SR. LAC failures occur on the SAP that has been configured on the pipe service, PSN bits are set by SDP-binding failures on the pipe service. The pwNotForwarding bit is set when none of the above failures apply, such as an MTU mismatch failure. This value is only applicable if the peer is using the pseudowire status signaling method to indicate faults. pwNotForwarding — Pseudowire not forwarding lacIngressFault Local — Attachment circuit RX fault lacEgressFault Local — Attachment circuit TX fault psnIngressFault Local — PSN-facing PW RX fault psnEgressFault Local — PSN-facing PW TX fault pwFwdingStandby — Pseudowire in standby mode |
Signaling Override |
The overriding signaled pseudowire type, as configured under the signaled-vc-type-override option for Apipes. This field is only displayed if signaled-vc-type-override is configured for the 7750 SR. |
all
Syntax
all
Context
[Tree] (show>service>id all)
Full Context
show service id all
Description
This command displays detailed information for all aspects of the service.
Platforms
All
Output
The following output is an example of a service displaying all information.
Output Example*A:PE# show service id 1 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : VPLS
Name : 1
Description : (Not Specified)
Customer Id : 1 Creation Origin : manual
Last Status Change: 08/31/2018 11:46:13
Last Mgmt Change : 08/31/2018 11:46:13
Etree Mode : Disabled
Admin State : Up Oper State : Up
MTU : 1514
SAP Count : 2 SDP Bind Count : 0
Snd Flush on Fail : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Propagate MacFlush: Disabled Per Svc Hashing : Disabled
Allow IP Intf Bind: Disabled
Fwd-IPv4-Mcast-To*: Disabled Fwd-IPv6-Mcast-To*: Disabled
Mcast IPv6 scope : mac-based
Def. Gateway IP : None
Def. Gateway MAC : None
Temp Flood Time : Disabled Temp Flood : Inactive
Temp Flood Chg Cnt: 0
SPI load-balance : Disabled
TEID load-balance : Disabled
Src Tep IP : N/A
Vxlan ECMP : Disabled
-------------------------------------------------------------------------------
BGP Information
-------------------------------------------------------------------------------
PW-Template Id : None
-------------------------------------------------------------------------------
Split Horizon Group specifics
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults : ignore
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/1
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/1 Encap : null
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 11:46:13
Last Mgmt Change : 08/31/2018 11:46:13
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Etree Root Leaf Tag: Disabled Etree Leaf Tag : 0
Etree Leaf AC : Disabled
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
OAM MAC Addr : 0 DHCP MAC Addr : 0
Host MAC Addr : 0 Intf MAC Addr : 0
SPB MAC Addr : 0 Cond MAC Addr : 0
BGP EVPN Addr : 0 EVPN Static Addr : 0
Admin MTU : 1514 Oper MTU : 1514
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
ARP Reply Agent : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Mac Learning : Enabled Discard Unkwn Srce: Disabled
Mac Aging : Enabled Mac Pinning : Disabled
BPDU Translation : Disabled
L2PT Termination : Disabled
Vlan-translation : None
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Application Profile: None
Transit Policy : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Cflowd : Disabled
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
MCAC Policy Name : MCAC Const Adm St : Enable
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
Use LAG port weight: no
MCAC If-Policy Name:
Restr MacUnpr Dst : Disabled
Auto Learn Mac Prot: Disabled
RestMacProtSrc Act : none
Time to RetryReset : never Retries Left : 3
Mac Move : Blockable Blockable Level : Tertiary
Auth Policy : None
DestMac Rewrite : Disabled
SendBvplsEvpnFlush : Enabled
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a V-MEP Filtering : Disabled
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : N/A Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
CIST Desig Bridge : N/A Designated Port : N/A
Forward transitions: 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State : outOfService
Host Limit : 1 Min Auth Interval : 15 minutes
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
DHCP
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down Lease Populate : 0
DHCP Snooping : Down Action : Keep
Proxy Admin State : Down
Proxy Lease Time : N/A
Emul. Server Addr : Not Configured
-------------------------------------------------------------------------------
DHCP6
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down
DHCP Snooping : Down
Interface-Id : AsciiTuple Remote-Id : Disabled
-------------------------------------------------------------------------------
Subscriber Management
-------------------------------------------------------------------------------
Admin State : Down MAC DA Hashing : False
Def Sub-Id : None
Def Sub-Profile : None
Def SLA-Profile : None
Def Inter-Dest-Id : None
Def App-Profile : None
Sub-Ident-Policy : None
Subscriber Limit : 1
Single-Sub-Parameters
Prof Traffic Only : False
Non-Sub-Traffic : N/A
Static host management
MAC learn options : N/A
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : N/A
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 11 (Multipoint) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Managed : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
SAP 1/1/9:1
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/9:1 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 11:46:13
Last Mgmt Change : 08/31/2018 11:46:13
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Etree Root Leaf Tag: Disabled Etree Leaf Tag : 0
Etree Leaf AC : Disabled
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
OAM MAC Addr : 0 DHCP MAC Addr : 0
Host MAC Addr : 0 Intf MAC Addr : 0
SPB MAC Addr : 0 Cond MAC Addr : 0
BGP EVPN Addr : 0 EVPN Static Addr : 0
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
ARP Reply Agent : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Mac Learning : Enabled Discard Unkwn Srce: Disabled
Mac Aging : Enabled Mac Pinning : Disabled
BPDU Translation : Disabled
L2PT Termination : Disabled
Vlan-translation : None
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Application Profile: None
Transit Policy : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Cflowd : Disabled
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
MCAC Policy Name : MCAC Const Adm St : Enable
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
Use LAG port weight: no
MCAC If-Policy Name:
Restr MacUnpr Dst : Disabled
Auto Learn Mac Prot: Disabled
RestMacProtSrc Act : none
Time to RetryReset : never Retries Left : 3
Mac Move : Blockable Blockable Level : Tertiary
Auth Policy : None
DestMac Rewrite : Disabled
SendBvplsEvpnFlush : Enabled
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a V-MEP Filtering : Disabled
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : N/A Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
CIST Desig Bridge : N/A Designated Port : N/A
Forward transitions: 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State : outOfService
Host Limit : 1 Min Auth Interval : 15 minutes
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
DHCP
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down Lease Populate : 0
DHCP Snooping : Down Action : Keep
Proxy Admin State : Down
Proxy Lease Time : N/A
Emul. Server Addr : Not Configured
-------------------------------------------------------------------------------
DHCP6
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down
DHCP Snooping : Down
Interface-Id : AsciiTuple Remote-Id : Disabled
-------------------------------------------------------------------------------
Subscriber Management
-------------------------------------------------------------------------------
Admin State : Down MAC DA Hashing : False
Def Sub-Id : None
Def Sub-Profile : None
Def SLA-Profile : None
Def Inter-Dest-Id : None
Def App-Profile : None
Sub-Ident-Policy : None
Subscriber Limit : 1
Single-Sub-Parameters
Prof Traffic Only : False
Non-Sub-Traffic : N/A
Static host management
MAC learn options : N/A
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : N/A
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 11 (Multipoint) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Managed : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state : Up Core Connectivity : Down
Stp Admin State : Down Stp Oper State : Down
Mode : Rstp Vcp Active Prot. : N/A
Bridge Id : 80:00.d8:2c:ff:00:00:00 Bridge Instance Id: 0
Bridge Priority : 32768 Tx Hold Count : 6
Topology Change : Inactive Bridge Hello Time : 2
Last Top. Change : 0d 00:00:00 Bridge Max Age : 20
Top. Change Count : 0 Bridge Fwd Delay : 15
MST region revision: 0 Bridge max hops : 20
MST region name :
Root Bridge : N/A
Primary Bridge : N/A
Root Path Cost : 0 Root Forward Delay: 0
Rcvd Hello Time : 0 Root Max Age : 0
Root Priority : 0 Root Port : N/A
-------------------------------------------------------------------------------
Forwarding Database specifics
-------------------------------------------------------------------------------
Service Id : 1 Mac Move : Disabled
Primary Factor : 3 Secondary Factor : 2
Mac Move Rate : 2 Mac Move Timeout : 10
Mac Move Retries : 3
Table Size : 250 Allocated Count : 0
Total In Use : 0
Learned Count : 0 Static Count : 0
OAM MAC Count : 0 DHCP MAC Count : 0
Host MAC Count : 0 Intf MAC Count : 0
Spb Count : 0 Cond MAC Count : 0
BGP EVPN Count : 0 EVPN Static Cnt : 0
EVPN Dup Det Cnt : 0
Remote Age : 900 Local Age : 300
High Watermark : 95% Low Watermark : 90%
Mac Learning : Enabled Discard Unknown : Disabled
Mac Aging : Enabled Relearn Only : False
Mac Subnet Len : 48
Sel Learned FDB : Disabled
-------------------------------------------------------------------------------
IGMP Snooping Base info
-------------------------------------------------------------------------------
Admin State : Down
Querier : No querier found
-------------------------------------------------------------------------------
Port Oper MRtr Pim Send Max Max Max MVR Num
Id Stat Port Port Qrys Grps Srcs Grp From-VPLS Grps
Srcs
-------------------------------------------------------------------------------
sap:1/1/1 Up No No No None None None Local 0
sap:1/1/9:1 Up No No No None None None Local 0
-------------------------------------------------------------------------------
MLD Snooping Base info
-------------------------------------------------------------------------------
Admin State : Down
Querier : No querier found
-------------------------------------------------------------------------------
Port Oper MRtr Send Max Num MVR Num
Id State Port Queries Groups From-VPLS Groups
-------------------------------------------------------------------------------
sap:1/1/1 Up No Disabled No Limit Local 0
sap:1/1/9:1 Up No Disabled No Limit Local 0
-------------------------------------------------------------------------------
DHCP Summary, service 1
-------------------------------------------------------------------------------
Sap/Sdp Snoop Used/ Arp Reply Info Admin
Provided Agent Option State
-------------------------------------------------------------------------------
sap:1/1/1 No 0/0 No Keep Down
sap:1/1/9:1 No 0/0 No Keep Down
-------------------------------------------------------------------------------
Number of Entries : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
ARP host Summary, service 1
-------------------------------------------------------------------------------
Sap Used Provided Admin State
-------------------------------------------------------------------------------
sap:1/1/1 0 1 outOfService
sap:1/1/9:1 0 1 outOfService
-------------------------------------------------------------------------------
Number of SAPs : 2 0
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
-------------------------------------------------------------------------------
WLAN Gateway specifics
-------------------------------------------------------------------------------
Admin State : disabled
Description : (Not Specified)
SAP-template : (Not Specified)
Last management change : (Not Specified)
No associated WLAN Gateway interface VLAN tag ranges found.
===============================================================================
===============================================================================
Service VPLS Group Information
===============================================================================
===============================================================================
===============================================================================
Egress VTEP, VNI
===============================================================================
Instance VTEP Address Egress VNI Evpn/ Static
Mcast Oper State L2 PBR Static Num.
MACs
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
-------------------------------------------------------------------------------
===============================================================================
VPLS Sites
===============================================================================
Site Site-Id Dest Mesh-SDP Admin Oper Fwdr
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:PE#
Show Service ID All Output Fields describes the command output fields.
Label |
Description |
---|---|
Service Id |
The service identifier. |
VPN Id |
The number which identifies the VPN. |
Service Type |
Specifies the type of service. |
SDP Id |
The SDP identifier. |
Description |
Generic information about the service. |
Customer Id |
The customer identifier. |
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
SAP Count |
The number of SAPs specified for this service. |
SDP Bind Count |
The number of SDPs bound to this service. |
Split Horizon Group |
Name of the split horizon group for this service. |
Description |
Description of the split horizon group. |
Last Changed |
The date and time of the most recent management-initiated change to this split horizon group. |
SDP Id |
The SDP identifier. |
Type |
Indicates whether this service SDP binding is a spoke or a mesh. |
Admin Path MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Delivery |
Specifies the type of delivery used by the SDP: GRE or MPLS. |
Admin State |
The administrative state of this SDP. |
Oper State |
The operational state of this SDP. |
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
Ingress Filter |
The ID of the ingress filter policy. |
Egress Filter |
The ID of the egress filter policy. |
Far End |
Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Last Changed |
The date and time of the most recent change to this customer. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
SDP Delivery Mechanism |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the Far End field. If the SDP type is GRE, then the following message displays: SDP Delivery Mechanism is not MPLS |
Number of SDPs |
The total number SDPs applied to this service ID. |
Service Id |
The service identifier. |
Port Id |
The ID of the access port where this SAP is defined. |
Description |
Generic information about the SAP. |
Encap Value |
The value of the label used to identify this SAP on the access port. |
Admin State |
The administrative state of the SAP. |
Oper State |
The operating state of the SAP. |
Last Changed |
The date and time of the last change. |
Admin MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Ingress qos-policy |
The SAP ingress QoS policy ID. |
Egress qos-policy |
The SAP egress QoS policy ID. |
Ingress Filter-Id |
The SAP ingress filter policy ID. |
Egress Filter-Id |
The SAP egress filter policy ID. |
Multi Svc Site |
Indicates the multi-service site that the SAP is a member. |
Ingress sched-policy |
Indicates the ingress QoS scheduler for the SAP. |
Egress sched-policy |
Indicates the egress QoS scheduler for the SAP. |
Acct. Pol |
Indicates the accounting policy applied to the SAP. |
Collect Stats |
Specifies whether accounting statistics are collected on the SAP. |
Dropped |
The number of packets or octets dropped. |
Offered Hi Priority |
The number of high priority packets, as determined by the SAP ingress QoS policy. |
Offered Low Priority |
The number of low priority packets, as determined by the SAP ingress QoS policy. |
Offered Low Priority |
The number of low priority packets, as determined by the SAP ingress QoS policy. |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
Dropped In Profile |
The number of in-profile packets or octets discarded. |
Dropped Out Profile |
The number of out-of-profile packets or octets discarded. |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
Ingress Queue 1 |
The index of the ingress QoS queue of this SAP. |
High priority offered |
The packets or octets count of the high priority traffic for the SAP. |
High priority dropped |
The number of high priority traffic packets/octets dropped. |
Low priority offered |
The packets or octets count of the low priority traffic. |
Low priority dropped |
The number of low priority traffic packets/octets dropped. |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Out profile forwarded |
The number of out-of-profile octets (rate above CIR) forwarded. |
Egress Queue 1 |
The index of the egress QoS queue of the SAP. |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded. |
In profile dropped |
The number of in-profile packets or octets dropped for the SAP. |
Out profile forwarded |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
Out profile dropped |
The number of out-of-profile packets or octets discarded. |
State |
Specifies whether DHCP Relay is enabled on this SAP. |
Info Option |
Specifies whether Option 82 processing is enabled on this SAP. |
Action |
Specifies the Option 82 processing on this SAP or interface: keep, replace or drop. |
Circuit ID |
Specifies whether the If Index is inserted in Circuit ID sub-option of Option 82. |
Remote ID |
Specifies whether the far-end MAC address is inserted in Remote ID sub-option of Option 82. |
Managed by Service |
Specifies the service-id of the management VPLS managing this SAP. |
Managed by MSTI |
Specifies the MST instance inside the management VPLS managing this SAP. |
Last BPDU from |
The bridge ID of the sender of the last BPDU received on this SAP. |
Managed by SAP |
Specifies the sap-id inside the management VPLS managing this SAP. |
Prune state |
Specifies the STP state inherited from the management VPLS. |
Managed by Service |
Specifies the service-id of the management VPLS managing this spoke-SDP. |
Last BPDU from |
The bridge ID of the sender of the last BPDU received on this SAP. |
Managed by Spoke |
Specifies the sap-id inside the management VPLS managing this spoke-SDP. |
Prune state |
Specifies the STP state inherited from the management VPLS. |
Peer Pw Bits |
Indicates the bits set by the LDP peer when there is a fault on its side of the pseudowire. LAC failures occur on the SAP that has been configured on the pipe service, PSN bits are set by SDP-binding failures on the pipe service. The pwNotForwarding bit is set when none of the above failures apply, such as an MTU mismatch failure. This value is only applicable if the peer is using the pseudowire status signaling method to indicate faults. pwNotForwarding — Pseudowire not forwarding. lacIngressFault Local — Attachment circuit RX fault. lacEgressFault Local — Attachment circuit TX fault. psnIngressFault Local — PSN-facing PW RX fault. psnEgressFault Local — PSN-facing PW TX fault. pwFwdingStandby — Pseudowire in standby mode. |
all
Syntax
all
Context
[Tree] (show>service>id all)
Full Context
show service id all
Description
This command displays detailed information for all aspects of the service.
Platforms
All
Output
The following output is an example of service id information, and Show All Service-ID Field Descriptions describes the output fields.
Output ExampleA:PE# show service id 500 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 500 Vpn Id : 0
Service Type : IES
Name : 500
Description : (Not Specified)
Customer Id : 1 Creation Origin : manual
Last Status Change: 08/31/2018 16:07:55
Last Mgmt Change : 08/31/2018 16:07:55
Admin State : Up Oper State : Up
SAP Count : 2 SDP Bind Count : 0
-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults : ignore
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/9:1
-------------------------------------------------------------------------------
Service Id : 500
SAP : 1/1/9:1 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 16:07:55
Last Mgmt Change : 08/31/2018 16:07:55
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Application Profile: None
Transit Policy : None
AARP Id : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : 08/31/2018 16:19:29
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
SAP pw-1:500
-------------------------------------------------------------------------------
Service Id : 500
SAP : pw-1:500 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 16:09:16
Last Mgmt Change : 08/31/2018 16:07:55
Sub Type : regular
Split Horizon Group: (Not Specified)
Admin MTU : 1518 Oper MTU : 8660
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Limit Unused BW : Disabled
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Application Profile: None
Transit Policy : None
AARP Id : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 500
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : pw-sap
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : 08/31/2018 16:19:29
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 500)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
Service Interfaces
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Interface
-------------------------------------------------------------------------------
If Name : int
Admin State : Up Oper (v4/v6) : Up/Down
Down Reason V6 : ifProtoOperDown
Protocols : None
IP Addr/mask : 192.168.0.1/24 Address Type : Primary
IGP Inhibit : Disabled Broadcast Address : Host-ones
HoldUp-Time : 0 Track Srrp Inst : 0
Description : N/A
Ignore Port State : None
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Description : (Not Specified)
If Index : 4 Virt. If Index : 4
Last Oper Chg : 08/31/2018 16:14:20 Global If Index : 258
Mon Oper Grp : None
Srrp En Rtng : Disabled Hold time : N/A
SAP Id : pw-1:500
TOS Marking : Untrusted If Type : IES
SNTP B.Cast : False IES ID : 500
MAC Address : d8:2c:ff:00:00:00 Mac Accounting : Disabled
Ingress stats : Disabled IPv6 DAD : Enabled
TCP MSS V4 : 0 TCP MSS V6 : 0
ARP Timeout : 14400s IPv6 Nbr ReachTime: 30s
ARP Retry Timer : 5000ms IPv6 stale time : 14400s
ARP Limit : Disabled IPv6 Nbr Limit : Disabled
ARP Threshold : Disabled IPv6 Nbr Threshold: Disabled
ARP Limit Log Only: Disabled IPv6 Nbr Log Only : Disabled
ARP Learn Unsolic*: Disabled ND Learn Unsolici*: None
ARP Proactive Ref*: Disabled ND Proactive Refr*: None
ARP Populate Host : Disabled ND Populate Host : Disabled
ARP Route Tag : 0 ND Route tag : 0
IP MTU : (default)
IP Oper MTU : 8660
ARP Populate : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Cflowd (unicast) : None Cflowd (multicast): None
LdpSyncTimer : None
LSR Load Balance : system
EGR Load Balance : both
Vas If Type : none
TEID Load Balance : Disabled
SPI Load Balance : Disabled
uRPF Chk : disabled
uRPF Ipv6 Chk : disabled
uRPF Select VPRN : False
PTP HW Assist : Disabled
Rx Pkts : 0 Rx Bytes : 0
Rx V4 Pkts : N/A Rx V4 Bytes : N/A
Rx V6 Pkts : N/A Rx V6 Bytes : N/A
Tx DBcast Dis. Pk*: 0 Tx DBcast Dis. By*: 0
Mpls Rx Pkts : 0 Mpls Rx Bytes : 0
Mpls Tx Pkts : 0 Mpls Tx Bytes : 0
OperDCpuProtPlcy : N/A
Proxy ARP Details
Rem Proxy ARP : Disabled Local Proxy ARP : Disabled
Policies : none
Proxy Neighbor Discovery Details
Local Pxy ND : Disabled
Policies : none
DHCP no local server
DHCP Details
Description : (Not Specified)
Admin State : Down Lease Populate : 0
Gi-Addr : 192.168.0.1* Gi-Addr as Src Ip : Disabled
* = inferred gi-address from interface IP address
Action : Keep Trusted : Disabled
DHCP Proxy Details
Admin State : Down
Lease Time : N/A
Emul. Server : Not configured
DHCP Relay Proxy Details
Relay ucast : none
Siaddr ovr : N/A
Subscriber Authentication Details
Auth Policy : None
DHCP6 Relay Details
Description : (Not Specified)
Admin State : Down Lease Populate : 0
Oper State : Down Nbr Resolution : Disabled
If-Id Option : None Remote Id : Disabled
Src Addr : Not configured
Python plcy : (Not Specified)
DHCP6 Server Details
Admin State : Down Max. Lease States : 8000
ISA Tunnel redundant next-hop information
Static Next-Hop :
Dynamic Next-Hop :
ICMP Details
Redirects : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
Parameter Problem: Number - 100 Time (seconds) - 10
ICMP Mask Reply : True
ICMPv6 Details
Packet Too Big : Number - 100 Time (seconds) - 10
Parameter Problem: Number - 100 Time (seconds) - 10
Redirects : Number - 100 Time (seconds) - 10
Time Exceeded : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
IPCP Address Extension Details
Peer IP Addr : Not configured
Peer Pri DNS Addr : Not configured
Peer Sec DNS Addr : Not configured
Network Domains Associated
default
-------------------------------------------------------------------------------
Admin Groups
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Srlg Groups
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QoS Queue-Group Redirection Details
-------------------------------------------------------------------------------
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
-------------------------------------------------------------------------------
Interface
-------------------------------------------------------------------------------
If Name : int1
Admin State : Up Oper (v4/v6) : Up/Down
Down Reason V6 : ifProtoOperDown
Protocols : None
IP Addr/mask : 20.0.0.1/30 Address Type : Primary
IGP Inhibit : Disabled Broadcast Address : Host-ones
HoldUp-Time : 0 Track Srrp Inst : 0
Description : N/A
Ignore Port State : None
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Description : (Not Specified)
If Index : 5 Virt. If Index : 5
Last Oper Chg : 08/31/2018 16:07:55 Global If Index : 259
Mon Oper Grp : None
Srrp En Rtng : Disabled Hold time : N/A
SAP Id : 1/1/9:1
TOS Marking : Untrusted If Type : IES
SNTP B.Cast : False IES ID : 500
MAC Address : d8:2c:01:01:00:09 Mac Accounting : Disabled
Ingress stats : Disabled IPv6 DAD : Enabled
TCP MSS V4 : 0 TCP MSS V6 : 0
ARP Timeout : 14400s IPv6 Nbr ReachTime: 30s
ARP Retry Timer : 5000ms IPv6 stale time : 14400s
ARP Limit : Disabled IPv6 Nbr Limit : Disabled
ARP Threshold : Disabled IPv6 Nbr Threshold: Disabled
ARP Limit Log Only: Disabled IPv6 Nbr Log Only : Disabled
ARP Learn Unsolic*: Disabled ND Learn Unsolici*: None
ARP Proactive Ref*: Disabled ND Proactive Refr*: None
ARP Populate Host : Disabled ND Populate Host : Disabled
ARP Route Tag : 0 ND Route tag : 0
IP MTU : (default)
IP Oper MTU : 1500
ARP Populate : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Cflowd (unicast) : None Cflowd (multicast): None
LdpSyncTimer : None
LSR Load Balance : system
EGR Load Balance : both
Vas If Type : none
TEID Load Balance : Disabled
SPI Load Balance : Disabled
uRPF Chk : disabled
uRPF Ipv6 Chk : disabled
uRPF Select VPRN : False
PTP HW Assist : Disabled
Rx Pkts : 3 Rx Bytes : 0
Rx V4 Pkts : N/A Rx V4 Bytes : N/A
Rx V6 Pkts : N/A Rx V6 Bytes : N/A
Tx Pkts : 5 Tx Bytes : 530
Tx V4 Pkts : 5 Tx V4 Bytes : 530
Tx V4 Discard Pkts: 0 Tx V4 Discard Byt*: 0
Tx V6 Pkts : 0 Tx V6 Bytes : 0
Tx V6 Discard Pkts: 0 Tx V6 Discard Byt*: 0
Tx DBcast Dis. Pk*: 0 Tx DBcast Dis. By*: 0
Mpls Rx Pkts : 0 Mpls Rx Bytes : 0
Mpls Tx Pkts : 0 Mpls Tx Bytes : 0
OperDCpuProtPlcy : N/A
Proxy ARP Details
Rem Proxy ARP : Disabled Local Proxy ARP : Disabled
Policies : none
Proxy Neighbor Discovery Details
Local Pxy ND : Disabled
Policies : none
DHCP no local server
DHCP Details
Description : (Not Specified)
Admin State : Down Lease Populate : 0
Gi-Addr : 20.0.0.1* Gi-Addr as Src Ip : Disabled
* = inferred gi-address from interface IP address
Action : Keep Trusted : Disabled
DHCP Proxy Details
Admin State : Down
Lease Time : N/A
Emul. Server : Not configured
DHCP Relay Proxy Details
Relay ucast : none
Siaddr ovr : N/A
Subscriber Authentication Details
Auth Policy : None
DHCP6 Relay Details
Description : (Not Specified)
Admin State : Down Lease Populate : 0
Oper State : Down Nbr Resolution : Disabled
If-Id Option : None Remote Id : Disabled
Src Addr : Not configured
Python plcy : (Not Specified)
DHCP6 Server Details
Admin State : Down Max. Lease States : 8000
ISA Tunnel redundant next-hop information
Static Next-Hop :
Dynamic Next-Hop :
ICMP Details
Redirects : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
Parameter Problem: Number - 100 Time (seconds) - 10
ICMP Mask Reply : True
ICMPv6 Details
Packet Too Big : Number - 100 Time (seconds) - 10
Parameter Problem: Number - 100 Time (seconds) - 10
Redirects : Number - 100 Time (seconds) - 10
Time Exceeded : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
IPCP Address Extension Details
Peer IP Addr : Not configured
Peer Pri DNS Addr : Not configured
Peer Sec DNS Addr : Not configured
Network Domains Associated
default
-------------------------------------------------------------------------------
Admin Groups
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Srlg Groups
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QoS Queue-Group Redirection Details
-------------------------------------------------------------------------------
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
===============================================================================
* indicates that the corresponding row element may have been truncated.
A:PE#
Label |
Description |
---|---|
Service Detailed Information |
|
Service Id |
The service identifier. |
VPN Id |
The number which identifies the VPN. |
Service Type |
Specifies the type of service. |
SDP Id |
The SDP identifier. |
Description |
Generic information about the service. |
Customer Id |
The customer identifier. |
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
SAP Count |
The number of SAPs specified for this service. |
SDP Bind Count |
The number of SDPs bound to this service. |
Service Destination Points (SDPs) |
|
SDP Id |
The SDP identifier. |
Type |
Indicates whether this Service SDP binding is a spoke or a mesh. |
Admin Path MTU |
The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Delivery |
Specifies the type of delivery used by the SDP: GRE or MPLS. |
Admin State |
The administrative state of this SDP. |
Oper State |
The operational state of this SDP. |
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
Ingress Filter |
The ID of the ingress filter policy. |
Egress Filter |
The ID of the egress filter policy. |
Far End |
Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Last Changed |
The date and time of the most recent change to this customer. |
Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
Admin State |
Specifies the operating status of the service. |
Oper State |
The current status of the service. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
SDP Delivery Mechanism |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far-end field. If the SDP type is GRE, then the following message displays: "SDP Delivery Mechanism is not MPLS”. |
Number of SDPs |
The total number SDPs applied to this service ID. |
Service Access Points |
|
Service Id |
The service identifier. |
Port Id |
The ID of the access port where this SAP is defined. |
Description |
Generic information about the SAP. |
Encap |
The value of the label used to identify this SAP on the access port. |
Admin State |
The desired state of the SAP. |
Oper State |
The operating state of the SAP. |
Last Changed |
The date and time of the last change. |
Admin MTU |
The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Ingress qos-policy |
The SAP ingress QoS policy ID. |
Egress qos-policy |
The SAP egress QoS policy ID. |
Ingress Filter-Id |
The SAP ingress filter policy ID. |
Egress Filter-Id |
The SAP egress filter policy ID. |
Multi Svc Site |
Indicates the multi-service site that the SAP is a member. |
Ingress sched-policy |
Indicates the ingress QoS scheduler for the SAP. |
Egress sched-policy |
Indicates the egress QoS scheduler for the SAP. |
Acct. Pol |
Indicates the accounting policy applied to the SAP. |
Collect Stats |
Specifies whether accounting statistics are collected on the SAP. |
SAP Statistics |
|
Dropped |
The number of packets or octets dropped. |
Offered Hi Priority |
The number of high priority packets, as determined by the SAP ingress QoS policy. |
Offered Low Priority |
The number of low priority packets, as determined by the SAP ingress QoS policy. |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
Queueing Stats |
|
Dropped In Profile |
The number of in-profile packets or octets discarded. |
Dropped Out Profile |
The number of out-of-profile packets or octets discarded. |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
SAP per Queue stats |
|
Ingress Queue 1 |
The index of the ingress QoS queue of this SAP. |
High priority offered |
The packets or octets count of the high priority traffic for the SAP. |
High priority dropped |
The number of high priority traffic packets/octets dropped. |
Low priority offered |
The packets or octets count of the low priority traffic. |
Low priority dropped |
The number of low priority traffic packets/octets dropped. |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Out profile forwarded |
The number of out-of-profile octets (rate above CIR) forwarded. |
Egress Queue 1 |
The index of the egress QoS queue of the SAP. |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded. |
IPCP Address Extension Details |
|
In profile dropped |
The number of in-profile packets or octets dropped for the SAP. |
Peer IP Addr |
Specifies the remote IP address to be assigned to the far-end of the associated PPP/MLPPP link via IPCP extensions. |
Peer Pri DNS Addr |
Specifies a unicast IPv4 address for the primary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions. |
Peer Sec DNS Addr |
Specifies a unicast IPv4 address for the secondary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions (optional). |
all
Syntax
all
Context
[Tree] (show>service>id all)
Full Context
show service id all
Description
This command displays detailed information for all aspects of the service.
Platforms
All
Output
The following output is an example of show all service-ID information, and Show All Service-ID Field Descriptions describes the output fields.
Output ExampleIng ipv6 Fltr and Egr ipv6 Fltr are for the 7750 SR only.
Output Example
show service id all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 2 Vpn Id : 0
Service Type : VPRN
Name : (Not Specified)
Description : (Not Specified)
Customer Id : 1 Creation Origin : manual
Last Status Change: 08/21/2013 08:54:14
Last Mgmt Change : 08/21/2013 08:56:06
Admin State : Down Oper State : Down
Route Dist. : None VPRN Type : regular
AS Number : None Router Id : 18.18.18.18
ECMP : Enabled ECMP Max Routes : 1
Max IPv4 Routes : No Limit Auto Bind : None
Max IPv6 Routes : No Limit
Ignore NH Metric : Disabled
Hash Label : Disabled
Vrf Target : None
Vrf Import : None
Vrf Export : None
MVPN Vrf Target : None
MVPN Vrf Import : None
MVPN Vrf Export : None
Car. Sup C-VPN : Disabled
Label mode : vrf
BGP VPN Backup : Disabled
SAP Count : 0 SDP Bind Count : 0
-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults : ignore
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
No Sap Associations
-------------------------------------------------------------------------------
Service Interfaces
-------------------------------------------------------------------------------
No Interface Associations found.
-------------------------------------------------------------------------------
PTP Configuration
-------------------------------------------------------------------------------
Admin State : down Oper State : down
Peer Limit : 25
===============================================================================
show service id all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 9 Vpn Id : 0
Service Type : VPRN
Name : 9
Description : (Not Specified)
Customer Id : 1 Creation Origin : manual
Last Status Change: 08/31/2018 16:07:55
Last Mgmt Change : 08/31/2018 16:07:55
Admin State : Up Oper State : Up
Router Oper State : Up
Route Dist. : 65536:9 VPRN Type : regular
Oper Route Dist : 65536:9
Oper RD Type : configured
AS Number : None Router Id : 1.1.1.1
ECMP : Enabled ECMP Max Routes : 1
Max IPv4 Routes : No Limit
Auto Bind Tunnel
Resolution : disabled
Weighted ECMP : Disabled ECMP Max Routes : 1
Max IPv6 Routes : No Limit
Ignore NH Metric : Disabled
Hash Label : Disabled
Entropy Label : Disabled
Vrf Target : None
Vrf Import : None
Vrf Export : None
MVPN Vrf Target : None
MVPN Vrf Import : None
MVPN Vrf Export : None
Car. Sup C-VPN : Disabled
Label mode : vrf
BGP VPN Backup : Disabled
BGP Export Inactv : Disabled
SAP Count : 1 SDP Bind Count : 0
-------------------------------------------------------------------------------
ETH-CFM service specifics
-------------------------------------------------------------------------------
Tunnel Faults : ignore
-------------------------------------------------------------------------------
VPRN service Network Specifics
-------------------------------------------------------------------------------
Ing Net QoS Policy : none
Ingress FP QGrp : (none) Ing FP QGrp Inst : (none)
Ingress uRPF check : enabled
-------------------------------------------------------------------------------
===============================================================================
Vxlan Tunnel Termination
===============================================================================
Tunnel Term IP FPE ID Last Change
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/10:1
-------------------------------------------------------------------------------
Service Id : 9
SAP : 1/1/10:1 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 08/31/2018 16:07:55
Last Mgmt Change : 08/31/2018 16:07:55
Sub Type : regular
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Q Frame-Based Acct : Disabled Limit Unused BW : Disabled
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Application Profile: None
Transit Policy : None
AARP Id : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Bandwidth : Not-Applicable
Oper DCpu Prot Pol*: _default-access-policy
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Shared Q plcy : n/a Multipoint shared : Disabled
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
E. HS Sec. Shaper : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 0 0
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 0 0
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : 08/31/2018 16:29:08
Packets Octets
CPM Ingress : 0 0
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
For. In/InplusProf : 0 0
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
Service Interfaces
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Interface
-------------------------------------------------------------------------------
If Name : int
Admin State : Up Oper (v4/v6) : Up/Down
Down Reason V6 : ifProtoOperDown
Protocols : None
IP Addr/mask : 20.0.0.2/30 Address Type : Primary
IGP Inhibit : Disabled Broadcast Address : Host-ones
HoldUp-Time : 0 Track Srrp Inst : 0
Description : N/A
Ignore Port State : None
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Description : (Not Specified)
If Index : 3 Virt. If Index : 3
Last Oper Chg : 08/31/2018 16:07:55 Global If Index : 257
Mon Oper Grp : None
Srrp En Rtng : Disabled Hold time : N/A
SAP Id : 1/1/10:1
TOS Marking : Trusted If Type : VPRN
SNTP B.Cast : False
MAC Address : 00:00:00:00:00:01 Mac Accounting : Disabled
Ingress stats : Disabled IPv6 DAD : Enabled
TCP MSS V4 : 0 TCP MSS V6 : 0
ARP Timeout : 14400s IPv6 Nbr ReachTime: 30s
ARP Retry Timer : 5000ms IPv6 stale time : 14400s
ARP Limit : Disabled IPv6 Nbr Limit : Disabled
ARP Threshold : Disabled IPv6 Nbr Threshold: Disabled
ARP Limit Log Only: Disabled IPv6 Nbr Log Only : Disabled
ARP Learn Unsolic*: Disabled ND Learn Unsolici*: None
ARP Proactive Ref*: Disabled ND Proactive Refr*: None
ARP Populate Host : Disabled ND Populate Host : Disabled
ARP Route Tag : 0 ND Route tag : 0
IP MTU : (default)
IP Oper MTU : 1500
ARP Populate : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Cflowd (unicast) : None Cflowd (multicast): None
LdpSyncTimer : None
LSR Load Balance : system
EGR Load Balance : both
Vas If Type : none
TEID Load Balance : Disabled
SPI Load Balance : Disabled
uRPF Chk : disabled
uRPF Ipv6 Chk : disabled
PTP HW Assist : Disabled
Rx Pkts : 9 Rx Bytes : 0
Rx V4 Pkts : N/A Rx V4 Bytes : N/A
Rx V6 Pkts : N/A Rx V6 Bytes : N/A
Tx Pkts : 10 Tx Bytes : 1060
Tx V4 Pkts : 10 Tx V4 Bytes : 1060
Tx V4 Discard Pkts: 0 Tx V4 Discard Byt*: 0
Tx V6 Pkts : 0 Tx V6 Bytes : 0
Tx V6 Discard Pkts: 0 Tx V6 Discard Byt*: 0
Tx DBcast Dis. Pk*: 0 Tx DBcast Dis. By*: 0
Mpls Rx Pkts : 0 Mpls Rx Bytes : 0
Mpls Tx Pkts : 0 Mpls Tx Bytes : 0
OperDCpuProtPlcy : N/A
Proxy ARP Details
Rem Proxy ARP : Disabled Local Proxy ARP : Disabled
Policies : none
Proxy Neighbor Discovery Details
Local Pxy ND : Disabled
Policies : none
DHCP no local server
DHCP Details
Description : (Not Specified)
Admin State : Down Lease Populate : 0
Gi-Addr : 20.0.0.2* Gi-Addr as Src Ip : Disabled
* = inferred gi-address from interface IP address
Action : Keep Trusted : Disabled
DHCP Proxy Details
Admin State : Down
Lease Time : N/A
Emul. Server : Not configured
DHCP Relay Proxy Details
Relay ucast : none
Siaddr ovr : N/A
Subscriber Authentication Details
Auth Policy : None
DHCP6 Relay Details
Description : (Not Specified)
Admin State : Down Lease Populate : 0
Oper State : Down Nbr Resolution : Disabled
If-Id Option : None Remote Id : Disabled
Src Addr : Not configured
Python plcy : (Not Specified)
DHCP6 Server Details
Admin State : Down Max. Lease States : 8000
ISA Tunnel redundant next-hop information
Static Next-Hop :
Dynamic Next-Hop :
ICMP Details
Redirects : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
Parameter Problem: Number - 100 Time (seconds) - 10
ICMP Mask Reply : True
ICMPv6 Details
Packet Too Big : Number - 100 Time (seconds) - 10
Parameter Problem: Number - 100 Time (seconds) - 10
Redirects : Number - 100 Time (seconds) - 10
Time Exceeded : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
IPCP Address Extension Details
Peer IP Addr : Not configured
Peer Pri DNS Addr : Not configured
Peer Sec DNS Addr : Not configured
-------------------------------------------------------------------------------
Admin Groups
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Srlg Groups
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
QoS Queue-Group Redirection Details
-------------------------------------------------------------------------------
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
===============================================================================
* indicates that the corresponding row element may have been truncated.
A:PE#
The following command displays output that is relevant to PW SAPs and Show All Service-ID Field Descriptions describes the output fields.
show service id all
...
-------------------------------------------------------------------------------
SAP pw-3:3
-------------------------------------------------------------------------------
Service Id : 3
SAP : pw-3:3 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 02/03/2015 18:04:39
Last Mgmt Change : 02/03/2015 18:04:13
Sub Type : regular
Split Horizon Group: (Not Specified)
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit: max
Endpoint : N/A
Limit Unused BW : Disabled
Vlan-translation : None
Acct. Pol : None Collect Stats : Disabled
Application Profile: None
Transit Policy : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Ignore Oper Down : Disabled
Lag Link Map Prof : (none)
Cflowd : Disabled
-------------------------------------------------------------------------------
...
Label |
Description |
---|---|
Service Detailed Information |
|
Service Id |
The service identifier. |
VPN Id |
The number which identifies the VPN. |
Customer Id |
The customer identifier. |
Last Status Change |
The date and time of the most recent change in the administrative or operating status of the service. |
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
Admin State |
The current administrative state. |
Oper State |
The current operational state. |
Route Dist. |
Displays the route distribution number. |
AS Number |
Displays the autonomous system number. |
Router Id |
Displays the router ID for this service. |
ECMP |
Displays equal cost multipath information. |
ECMP Max Routes |
Displays the maximum number of routes that can be received from the neighbors in the group or for the specific neighbor. |
Max Routes |
Displays the maximum number of routes that can be used for path sharing. |
Auto Bind |
Specifies the automatic binding type for the SDP assigned to this service. |
Vrf Target |
Specifies the VRF target applied to this service. |
Vrf Import |
Specifies the VRF import policy applied to this service. |
Vrf Export |
Specifies the VRF export policy applied to this service. |
SDP Id |
The SDP identifier. |
Description |
Generic information about the service. |
SAP Count |
The number of SAPs specified for this service. |
SDP Bind Count |
The number of SDPs bound to this service. |
Split Horizon Group |
Name of the split horizon group for this service. |
Description |
Description of the split horizon group. |
Last Changed |
The date and time of the most recent management-initiated change to this split horizon group. |
ETH-CFM Service Specifics |
|
Tunnel Faults |
Whether tunnel faults are ignored or accepted. |
Service Destination Points (SDPs) |
|
SDP Id |
The SDP identifier. |
Type |
Indicates whether this Service SDP binding is a spoke or a mesh. |
Admin Path MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Delivery |
Specifies the type of delivery used by the SDP: GRE or MPLS. |
Admin State |
The administrative state of this SDP. |
Oper State |
The operational state of this SDP. |
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
Ingress Filter |
The ID of the ingress filter policy. |
Egress Filter |
The ID of the egress filter policy. |
Far End |
Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Last Changed |
The date and time of the most recent change to this customer. |
Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
Admin State |
Specifies the operating status of the keepalive protocol. |
Oper State |
The current status of the keepalive protocol. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
SDP Delivery Mechanism |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field. If the SDP type is GRE, then the following message displays: SDP delivery mechanism is not MPLS. |
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Number of SDPs |
The total number SDPs applied to this service ID. |
Service Access Points |
|
Service Id |
The service identifier. |
Port Id |
The ID of the access port where this SAP is defined. |
Description |
Generic information about the SAP. |
Encap Value |
The value of the label used to identify this SAP on the access port. |
Admin State |
The desired state of the SAP. |
Oper State |
The operating state of the SAP. |
Last Changed |
The date and time of the last change. |
Admin MTU |
The desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Ingress qos-policy |
The SAP ingress QoS policy ID. |
Egress qos-policy |
The SAP egress QoS policy ID. |
Ingress Filter-Id |
The SAP ingress filter policy ID. |
Egress Filter-Id |
The SAP egress filter policy ID. |
Multi Svc Site |
Indicates the multi-service site that the SAP is a member. |
Ingress sched-policy |
Indicates the ingress QoS scheduler for the SAP. |
Egress sched-policy |
Indicates the egress QoS scheduler for the SAP. |
Acct. Pol |
Indicates the accounting policy applied to the SAP. |
Collect Stats |
Specifies whether accounting statistics are collected on the SAP. |
SAP Statistics |
|
Dropped |
The number of packets or octets dropped. |
Offered Hi Priority |
The number of high priority packets, as determined by the SAP ingress QoS policy. |
Offered Low Priority |
The number of low priority packets, as determined by the SAP ingress QoS policy. |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
Queueing Stats |
|
Dropped In Profile |
The number of in-profile packets or octets discarded. |
Dropped Out Profile |
The number of out-of-profile packets or octets discarded. |
Forwarded In Profile |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Forwarded Out Profile |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
SAP per Queue stats |
|
Ingress Queue 1 |
The index of the ingress QoS queue of this SAP. |
High priority offered |
The packets or octets count of the high priority traffic for the SAP. |
High priority dropped |
The number of high priority traffic packets/octets dropped. |
Low priority offered |
The packets or octets count of the low priority traffic. |
Low priority dropped |
The number of low priority traffic packets/octets dropped. |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded. |
Out profile forwarded |
The number of out-of-profile octets (rate above CIR) forwarded. |
Egress Queue 1 |
The index of the egress QoS queue of the SAP. |
In profile forwarded |
The number of in-profile packets or octets (rate below CIR) forwarded. |
In profile dropped |
The number of in-profile packets or octets dropped for the SAP. |
Out profile forwarded |
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
Out profile dropped |
The number of out-of-profile packets or octets discarded. |
State |
Specifies whether DHCP relay is enabled on this SAP. |
Info Option |
Specifies whether Option 82 processing is enabled on this SAP. |
Action |
Specifies the Option 82 processing on this SAP or interface: keep, replace or drop. |
Circuit ID |
Specifies whether the If index is inserted in circuit ID sub-option of Option 82. |
Remote ID |
Specifies whether the far-end MAC address is inserted in Remote ID sub-option of Option 82. |
Service Access Points |
|
Managed by Service |
Specifies the service-id of the management VPLS managing this SAP. |
Managed by SAP |
Specifies the sap-id inside the management VPLS managing this SAP. |
Prune state |
Specifies the STP state inherited from the management VPLS. |
Spoke SDPs |
|
Managed by Service |
Specifies the service-id of the management VPLS managing this spoke SDP. |
Managed by Spoke |
Specifies the sap-id inside the management VPLS managing this spoke SDP. |
Prune state |
Specifies the STP state inherited from the management VPLS. |
Peer Pw Bits |
Indicates the bits set by the LDP peer when there is a fault on its side of the pseudowire. LAC failures occur on the SAP that has been configured on the pipe service, PSN bits are set by SDP-binding failures on the pipe service. The pwNotForwarding bit is set when none of the above failures apply, such as an MTU mismatch failure. This value is only applicable if the peer is using the pseudowire status signaling method to indicate faults. pwNotForwarding — Pseudowire not forwarding. lacIngressFault Local — Attachment circuit RX fault. lacEgressFault Local — Attachment circuit TX fault. psnIngressFault Local — PSN-facing PW RX fault. psnEgressFault Local — PSN-facing PW TX fault. pwFwdingStandby — Pseudowire in standby mode. |
IPCP Address Extension Details |
|
Peer IP Addr |
Specifies the remote IP address to be assigned to the far-end of the associated PPP/MLPPP link via IPCP extensions. |
Peer Pri DNS Addr |
Specifies a unicast IPv4 address for the primary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions. |
Peer Sec DNS Addr |
Specifies a unicast IPv4 address for the secondary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions. |
all
Syntax
all
Context
[Tree] (show>service>id>mld-snooping all)
Full Context
show service id mld-snooping all
Description
This command displays detailed information about MLD snooping.
Platforms
All
Output
The following output is an example of service MLD snooping information.
Output Example*A:rbae_C# show service id 1 mld-snooping all
===============================================================================
MLD Snooping info for service 1
-------------------------------------------------------------------------------
MLD Snooping Base info
-------------------------------------------------------------------------------
Admin State : Up
Querier : FE80:db8:12 on SAP 2/1/5
-------------------------------------------------------------------------------
Sap/Sdp Oper MRtr Send Max Num MVR Num
Id State Port Queries Groups From-VPLS Groups
-------------------------------------------------------------------------------
sap:1/1/4 Up No Disabled No Limit Local 0
sap:2/1/5 Up Yes Disabled No Limit Local 0
sdp:31:1 Up No Disabled No Limit N/A 0
sdp:36:1 Up No Disabled No Limit N/A 0
-------------------------------------------------------------------------------
MLD Snooping Querier info
-------------------------------------------------------------------------------
Sap Id : 2/1/5
IP Address : FE80:db8:12
Expires : 11s
Up Time : 0d 00:05:05
Version : 2
General Query Interval : 10s
Query Response Interval : 1.0s
Robust Count : 2
-------------------------------------------------------------------------------
MLD Snooping Multicast Routers
-------------------------------------------------------------------------------
MRouter
Sap/Sdp Id Up Time Expires Version
-------------------------------------------------------------------------------
FE80::12
2/1/5 0d 00:05:05 11s 2
-------------------------------------------------------------------------------
Number of mrouters: 1
-------------------------------------------------------------------------------
MLD Snooping Proxy-reporting DB
-------------------------------------------------------------------------------
Group Address
Mode Up Time Num Sources
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
MLD Snooping SAP 1/1/4 Port-DB
-------------------------------------------------------------------------------
Group Address
Mode Type From-VPLS Up Time Expires Num MC
Src Stdby
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
MLD Snooping SAP 2/1/5 Port-DB
-------------------------------------------------------------------------------
Group Address
Mode Type From-VPLS Up Time Expires Num MC
Src Stdby
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
MLD Snooping SDP 31:1 Port-DB
-------------------------------------------------------------------------------
Group Address
Mode Type From-VPLS Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
MLD Snooping SDP 36:1 Port-DB
-------------------------------------------------------------------------------
Group Address
Mode Type From-VPLS Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
MLD Snooping Static Source Groups
-------------------------------------------------------------------------------
MLD Snooping Statistics
-------------------------------------------------------------------------------
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 43 0 129
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 4 35 0
V1 Done 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad MLD Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Wrong Version : 0
Lcl-Scope Packets : 0
Rsvd-Scope Packets : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
MCAC Policy Drops : 0
MCS Failures : 0
MVR From VPLS Cfg Drops : 0
MVR To SAP Cfg Drops : 0
-------------------------------------------------------------------------------
MLD Snooping Multicast VPLS Registration info
-------------------------------------------------------------------------------
MLD Snooping Admin State : Up
MVR Admin State : Down
MVR Policy : None
-------------------------------------------------------------------------------
Local SAPs/SDPs
-------------------------------------------------------------------------------
Svc Id Sap/Sdp Oper From Num Local
Id State VPLS Groups
-------------------------------------------------------------------------------
1 sap:1/1/4 Up Local 0
1 sap:2/1/5 Up Local 0
1 sdp:31:1 Up N/A 0
1 sdp:36:1 Up N/A 0
-------------------------------------------------------------------------------
MVR SAPs (from-vpls=1)
-------------------------------------------------------------------------------
Svc Id Sap/Sdp Oper From Num MVR
Id State VPLS Groups
-------------------------------------------------------------------------------
No MVR SAPs found.
===============================================================================
*A:rbae_C#
all
Syntax
all
Context
[Tree] (show>service>id>igmp-snooping all)
Full Context
show service id igmp-snooping all
Description
Displays detailed information for all aspects of IGMP snooping on the VPLS service.
Platforms
All
Output
The following output is an example of IGMP snooping information.
Output ExampleThe following example applies to the 7750 SR:
*A:ALA-48>show>service>id>igmp-snooping>snooping# all
===============================================================================
IGMP Snooping info for service 750
===============================================================================
IGMP Snooping Base info
-------------------------------------------------------------------------------
Admin State : Up
Querier : No querier found
-------------------------------------------------------------------------------
Sap/Sdp Oper MRtr Send Max Num Num
Id State Port Queries Groups Groups
-------------------------------------------------------------------------------
sap:1/1/7:0 Down No Disabled No Limit 0
sdp:1:22 Down No Disabled No Limit 0
sdp:8:750 Down No Disabled No Limit 0
-------------------------------------------------------------------------------
IGMP Snooping Querier info
-------------------------------------------------------------------------------
No querier found for this service.
-------------------------------------------------------------------------------
IGMP Snooping Multicast Routers
-------------------------------------------------------------------------------
MRouter Sap/Sdp Id Up Time Expires Version
-------------------------------------------------------------------------------
Number of mrouters: 0
-------------------------------------------------------------------------------
IGMP Snooping Proxy-reporting DB
-------------------------------------------------------------------------------
Group Address Mode Type Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
------------------------------------------------------------------------------
IGMP Snooping SAP 1/1/7:0 Port-DB
-------------------------------------------------------------------------------
Group Address Mode Type Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
IGMP Snooping SDP 1:22 Port-DB
-------------------------------------------------------------------------------
Group Address Mode Type Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
IGMP Snooping SDP 8:750 Port-DB
-------------------------------------------------------------------------------
Group Address Mode Type Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
IGMP Snooping Static Source Groups
-------------------------------------------------------------------------------
IGMP Snooping Statistics
-------------------------------------------------------------------------------
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 0 0 0
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 0 0 0
V3 Reports 0 0 0
V2 Leaves 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad IP Checksum : 0
Bad IGMP Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
===============================================================================
*A:ALA-48>show>service>id>snooping#
The following example applies to the 7450 ESS:
*A:ALA-42>show>service>id>igmp-snooping>snooping# all
===============================================================================
IGMP Snooping info for service 100
===============================================================================
IGMP Snooping Base info
-------------------------------------------------------------------------------
Admin State : Up
Querier : 10.20.1.6 on SAP 2/2/1:100
-------------------------------------------------------------------------------
Sap/Sdp Oper MRtr Send Max Num MVR Num
Id State Port Queries Groups From-VPLS Groups
-------------------------------------------------------------------------------
sap:1/1/4 Up No Disabled No Limit Local 1
sap:2/2/1:100 Up No Disabled No Limit Local 0
-------------------------------------------------------------------------------
IGMP Snooping Querier info
-------------------------------------------------------------------------------
Sap Id : 2/2/1:100
IP Address : 10.20.1.6
Expires : 3s
Up Time : 0d 00:15:23
Version : 3
General Query Interval : 2s
Query Response Interval : 1.0s
Robust Count : 2
-------------------------------------------------------------------------------
IGMP Snooping Multicast Routers
-------------------------------------------------------------------------------
MRouter Sap/Sdp Id Up Time Expires Version
-------------------------------------------------------------------------------
10.20.1.6 2/2/1:100 0d 00:15:24 2s 3
-------------------------------------------------------------------------------
Number of mrouters: 1
-------------------------------------------------------------------------------
IGMP Snooping Proxy-reporting DB
-------------------------------------------------------------------------------
Group Address Mode Up Time Num Sources
-------------------------------------------------------------------------------
239.0.0.0 exclude 0d 00:00:04 0
-------------------------------------------------------------------------------
Number of groups: 1
-------------------------------------------------------------------------------
IGMP Snooping SAP 1/1/4 Port-DB
-------------------------------------------------------------------------------
Group Address Mode Type From-VPLS Up Time Expires Num Src
-------------------------------------------------------------------------------
239.0.0.0 exclude dynamic local 0d 00:00:05 4s 0
-------------------------------------------------------------------------------
Number of groups: 1
-------------------------------------------------------------------------------
IGMP Snooping SAP 2/2/1:100 Port-DB
-------------------------------------------------------------------------------
Group Address Mode Type From-VPLS Up Time Expires Num Src
-------------------------------------------------------------------------------
Number of groups: 0
-------------------------------------------------------------------------------
IGMP Snooping Static Source Groups
-------------------------------------------------------------------------------
IGMP Snooping Statistics
-------------------------------------------------------------------------------
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 463 0 463
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 0 0 0
V3 Reports 4 4 0
V2 Leaves 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad IP Checksum : 0
Bad IGMP Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
MVR From VPLS Cfg Drops : 0
MVR To SAP Cfg Drops : 0
-------------------------------------------------------------------------------
IGMP Snooping Multicast VPLS Registration info
-------------------------------------------------------------------------------
IGMP Snooping Admin State : Up
MVR Admin State : Down
MVR Policy : None
-------------------------------------------------------------------------------
Local SAPs/SDPs
-------------------------------------------------------------------------------
Svc Id Sap/Sdp Oper From Num Local
Id State VPLS Groups
-------------------------------------------------------------------------------
100 sap:1/1/4 Up Local 1
100 sap:2/2/1:100 Up Local 0
-------------------------------------------------------------------------------
MVR SAPs (from-vpls=100)
-------------------------------------------------------------------------------
Svc Id Sap/Sdp Oper From Num MVR
Id State VPLS Groups
-------------------------------------------------------------------------------
No MVR SAPs found.
-------------------------------------------------------------------------------
*A:ALA-42>show>service>id>snooping#
IGMP Snooping Show All Service-ID Field Descriptions describes the show all service ID command output fields:
Label |
Description |
---|---|
Admin State |
The administrative state of the IGMP instance |
Querier |
The address of the IGMP querier on the IP subnet to which the interface is attached |
Sap/Sdp Id |
The SAP and SDP IDs of the service ID |
Oper State |
The operational state of the SAP and SDP IDs of the service ID |
Mrtr Port |
The multicast router port |
Send Queries |
Send-queries command is enabled or disabled |
Max Num Groups |
The maximum number of multicast groups that can be joined on this SAP or SDP |
MVR From VPLS |
MVR from VPLS enabled |
Num Groups |
The actual number of multicast groups that can be joined on this SAP or SDP |
all
Syntax
all
Context
[Tree] (show>redundancy>multi-chassis all)
Full Context
show redundancy multi-chassis all
Description
This command displays brief multi-chassis redundancy information.
Platforms
All
Output
The following output is an example of multi-chassis all information, and Redundancy multi-chassis all Field Descriptions describes the output fields.
Output ExampleB:Dut-B# show redundancy multi-chassis all
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address : 10.10.10.2
Description : Mc-Lag peer 10.10.10.2
Authentication : Disabled
Source IP Address : 0.0.0.0
Admin State : Enabled
===============================================================================
B:Dut-B#
B:Dut-B# show lag detail
===============================================================================
LAG Details
===============================================================================
LAG 1
-------------------------------------------------------------------------------
Description: Description For LAG Number 1
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Lag-id : 1 Mode : access
Adm : up Opr : up
Thres. Exceeded Cnt : 9 Port Threshold : 0
Thres. Last Cleared : 05/20/2006 00:12:35 Threshold Action : down
Dynamic Cost : false Encap Type : null
Configured Address : 1c:71:ff:00:01:41 Lag-IfIndex : 1342177281
Hardware Address : 1c:71:ff:00:01:41 Adapt Qos : distribute
Hold-time Down : 0.0 sec
LACP : enabled Mode : active
LACP Transmit Intvl : fast LACP xmit stdby : enabled
Selection Criteria : highest-count Slave-to-partner : disabled
Number of sub-groups: 1 Forced : -
System Id : 1c:71:ff:00:00:00 System Priority : 32768
Admin Key : 32768 Oper Key : 32666
Prtr System Id : 20:f4:ff:00:00:00 Prtr System Priority : 32768
Prtr Oper Key : 32768
MC Peer Address : 10.10.10.2 MC Peer Lag-id : 1
MC System Id : 00:00:00:33:33:33 MC System Priority : 32888
MC Admin Key : 32666 MC Active/Standby : active
MC Lacp ID in use : true MC extended timeout : false
MC Selection Logic : peer decided
MC Config Mismatch : no mismatch
-------------------------------------------------------------------------------
Port-id Adm Act/Stdby Opr Primary Sub-group Forced Prio
-------------------------------------------------------------------------------
331/2/1 up active up yes 1 - 32768
331/2/2 up active up 1 - 32768
331/2/3 up active up 1 - 32768
331/2/4 up active up 1 - 32768
-------------------------------------------------------------------------------
Port-id Role Exp Def Dist Col Syn Aggr Timeout Activity
-------------------------------------------------------------------------------
331/2/1 actor No No Yes Yes Yes Yes Yes Yes
331/2/1 partner No No Yes Yes Yes Yes Yes Yes
331/2/2 actor No No Yes Yes Yes Yes Yes Yes
331/2/2 partner No No Yes Yes Yes Yes Yes Yes
331/2/3 actor No No Yes Yes Yes Yes Yes Yes
331/2/3 partner No No Yes Yes Yes Yes Yes Yes
331/2/4 actor No No Yes Yes Yes Yes Yes Yes
331/2/4 partner No No Yes Yes Yes Yes Yes Yes
===============================================================================
B:Dut-B#
Label |
Description |
---|---|
Peer IP Address |
The multi-chassis redundancy peer. |
Description |
The text string describing the peer. |
Authentication |
If configured, displays the authentication key used between this node and the MC peer. |
Source IP Address |
The source address used to communicate with the MC peer. |
Admin State |
The administrative state of the peer. |
all
Syntax
all [color color] [end-point {ipv4-address | ipv6-address}] [preference preference-id] [distinguisher distinguisher-id] [tunnel-id tunnel-id]
all summary
Context
[Tree] (show>router>seg-rt>sr-policies all)
Full Context
show router segment-routing sr-policies all
Description
This command displays the traffic statistics of all or a filtered set of the BGP and static policies, or displays summary parameters.
Parameters
- color
-
Specifies the color to filter on.
- ipv4-address | ipv6-address
-
Specifies the end-point IPv4 or IPv6 address to filter on.
- preference-id
-
Specifies the preference ID to filter on.
- distinguisher-id
-
Specifies the distinguisher ID to filter on.
- summary
-
Displays the summary information for the BGP and static policies.
- tunnel-id
-
Specifies the tunnel ID to filter on.
Platforms
All
Output
The following output is an example of traffic statistics for all BGP and static policies.
Output Example
A:node-2# show router segment-routing sr-policies all
===============================================================================
SR-Policies Path
===============================================================================
-------------------------------------------------------------------------------
Type : srMpls
Active : No Owner : static
Color : 10
Head : 0.0.0.0 Endpoint Addr : 3ffe::a14:103
RD : 6 Preference : 10
BSID : 50001
TunnelId : 917508 Age : 12
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 LastReEvalReason: route-add
NumActPathChange: 0 Last Change : 08/18/2023 05:42:53
Act S-BFD Sess. : 1 S-BFD Threshold : 1
Maintenance Plcy: policy1
Ret Path BFD Lbl: 50008
Path Segment Lists:
Segment-List : 1 Weight : 1
Num Segments : 2 Last Change : 08/17/2023 17:11:08
1 MPLS Label : 524282 State : resolved-up
2 MPLS Label : 524280 State : N/A
-------------------------------------------------------------------------------
Type : srMpls
Active : Yes Owner : static
Color : 10
Head : 0.0.0.0 Endpoint Addr : 3ffe::a14:103
RD : 5 Preference : 20
BSID : 50001
TunnelId : 917508 Age : 12
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 LastReEvalReason: route-add
NumActPathChange: 0 Last Change : 08/18/2023 05:42:52
Act S-BFD Sess. : 1 S-BFD Threshold : 1
Maintenance Plcy: policy1
Ret Path BFD Lbl: 50008
Path Segment Lists:
Segment-List : 1 Weight : 1
Num Segments : 2 Last Change : 08/17/2023 17:11:08
1 MPLS Label : 524281 State : resolved-up
2 MPLS Label : 524282 State : N/A
===============================================================================
all
Syntax
all
Context
[Tree] (show>redundancy>multi-chassis>omcr all)
Full Context
show redundancy multi-chassis omcr all
Description
This command displays detailed information about OMCR.
Platforms
7750 SR
all-sources
all-sources
Syntax
all-sources
Context
[Tree] (tools>dump>app-assure>group>ipassist all-sources)
Full Context
tools dump application-assurance group ip-identification-assist all-sources
Description
This command displays the statistics related to IP identification assist for top applications.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of statistics related to IP identification assist for top applications.
Output Example
===============================================================================
Application-Assurance ip-identification-assist all-sources:
===============================================================================
group 1
ip-identification-assist no shutdown
passive-dns enabled
positive-app-id enabled
--------------------------------------------------------------------------------
isa 1/1
--------------------------------------------------------------------------------
Application Name IPs in cache IPs added IPs updated IP lookups found Parent Application Name
---------------------------------- ------------ ---------------------- ---------------------- ---------------------- ----------------------------------
"Application1" 6 6 0 0 "ParentApplication1"
Dns Snoop 6 6 0 0
Positive App Id 0 0 0 0
"Application2 " 4 4 0 0 "ParentApplication1"
Dns Snoop 4 4 0 0
Positive App Id 0 0 0 0
"Application3" 8 8 0 0 "ParentApplication1"
Dns Snoop 8 8 0 0
Positive App Id 0 0 0 0
"Application4" 12 12 0 0 "ParentApplication1"
Dns Snoop 12 12 0 0
Positive App Id 0 0 0 0
"Application5" 12 12 0 0 "ParentApplication2"
Dns Snoop 12 12 0 0
Positive App Id 0 0 0 0
"Application6" 53 53 0 0 "ParentApplication3"
Dns Snoop 53 53 0 0
Positive App Id 0 0 0 0
"Application7" 3 3 0 0 "ParentApplication3"
Dns Snoop 3 3 0 0
Positive App Id 0 0 0 0
"Application8" 6 6 0 0 "ParentApplication2"
Dns Snoop 6 6 0 0
Positive App Id 0 0 0 0
"Application9" 6 6 0 0 "ParentApplication4"
Dns Snoop 6 6 0 0
Positive App Id 0 0 0 0
"Application10" 16 16 0 0 "ParentApplication5"
Dns Snoop 16 16 0 0
Positive App Id 0 0 0 0
"Application11" 8 8 0 0 "ParentApplication6"
Dns Snoop 8 8 0 0
Positive App Id 0 0 0 0
"Application12" 6 6 0 0 "ParentApplication7"
Dns Snoop 6 6 0 0
Positive App Id 0 0 0 0
"Application13" 2 2 0 0 "ParentApplication2"
Dns Snoop 2 2 0 0
Positive App Id 0 0 0 0
"Application14" 8 8 0 0 "ParentApplication3"
Dns Snoop 8 8 0 0
Positive App Id 0 0 0 0
---------------------------------- ------------ ---------------------- ---------------------- ----------------------------------
TOTAL (14 applications) 150 150 0 0
Dns Snoop 150 150 0 0
Positive App Id 0 0 0 0
===============================================================================
all-subscriptions
all-subscriptions
Syntax
all-subscriptions
Context
[Tree] (show>log>cli all-subscriptions)
Full Context
show log cli all-subscriptions
Description
This command displays all subscriptions to all event logs that have a destination of 'cli'.
Platforms
All
ancp
ancp
Syntax
ancp ancp-sub-string string
Context
[Tree] (clear>subscr-mgmt ancp)
Full Context
clear subscriber-mgmt ancp
Description
This command clears subscriber ANCP data.
Parameters
- string
-
Specifies the ANCP string to clear, up to 63 characters, corresponding to this subscriber ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
ancp-policy
ancp-policy
Syntax
ancp-policy [policy-name]
ancp-policy policy-name association
Context
[Tree] (show>subscr-mgmt ancp-policy)
Full Context
show subscriber-mgmt ancp-policy
Description
This command displays subscriber Access Node Control Protocol (ANCP) policy information.
Parameters
- policy-name
-
Displays information for the specified ANCP policy.
- association
-
Displays the information configured with the ANCP policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management ANCP policy information.
Output ExampleA:cses-E11>config>subscr-mgmt>ancp# show subscriber-mgmt ancp-policy "test"
===============================================================================
ANCP Policy "test"
===============================================================================
I. Rate Reduction : 0 kbps
I. Rate Adjustment : 100 percent
I. Rate Monitor : 63360 kbps
I. Rate Monitor Alarm : Yes
I. Rate Modify : N/A
E. Rate Reduction : 0 kbps
E. Rate Adjustment : 100 percent
E. Rate Monitor : 0 kbps
E. Rate Monitor Alarm : no
E. Rate Modify : N/A
Port Down : N/A
Last Mgmt Change: 02/13/2013 19:15:28
===============================================================================
*A:cses-E11>config>subscr-mgmt>ancp#
ANCP Policy Field Descriptions describes ANCP policy output fields.
Field |
Description |
---|---|
I. Rate Reduction |
The ingress rate reduction to be applied for this subscriber in order to account for its video viewership |
I. Rate Adjustment |
The ingress rate adjustment |
I. Rate Monitor |
The ingress rate monitor |
I. Rate Monitor Alarm |
The ingress rate monitor alarm |
I. Rate Modify |
The ingress rate modification that is to be applied |
E. Rate Reduction |
The egress rate reduction to be applied for this subscriber in order to account for its video viewership |
E. Rate Adjustment |
The egress rate adjustment |
E. Rate Monitor |
The egress rate monitor |
E. Rate Monitor Alarm |
The egress rate monitor alarm |
E. Rate Modify |
The egress-rate modification that is to be applied |
Port Down |
The status of the port down configuration |
Last Mgmt Change |
The date and time of the last management change |
ancp-policy
Syntax
ancp-policy [policy-name]
Context
[Tree] (show>subscriber-management ancp-policy)
Full Context
show subscriber-mgmt ancp-policy
Description
This command displays subscriber ANCP policy information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management ANCP policy information.
Output ExampleA:active# show subscriber-mgmt ancp-policy
===============================================================================
ANCP Policies
===============================================================================
adsl-operator1
vdsl-operator1
-------------------------------------------------------------------------------
Number of ANCP policies : 2
===============================================================================
A:active#
A:active# show subscriber-mgmt ancp-policy adsl-operator1
===============================================================================
ANCP Policy "adsl-operator1"
===============================================================================
I. Rate Reduction : 0 kbps
I. Rate Adjustment : 100 percent
I. Rate Monitor : 0 kbps
I. Rate Monitor Alarm : no
I. Rate Modify : scheduler "root"
E. Rate Reduction : 10 kbps
E. Rate Adjustment : 100 percent
E. Rate Monitor : 0 kbps
E. Rate Monitor Alarm : no
E. Rate Modify : scheduler "root"
Port Down : N/A
Last Mgmt Change: 01/26/2007 17:10:51
================================================================================
A:active#
A:active# show subscriber-mgmt ancp-policy adsl-operator1 association
===============================================================================
ANCP Policy "adsl-operator1" associations
===============================================================================
SAP Static Map Associations
-------------------------------------------------------------------------------
- SAP : 1/1/3 Svc-id : 333 (VPLS)
String : "ANCP-String-1"
String : "ANCP-String-2"
------------------------------------------------------------------------------
MSS Static Map Associations
-------------------------------------------------------------------------------
- Cust-id : 1 MSS-name: mss1
String : "ANCP-String-3"
-------------------------------------------------------------------------------
Subscriber Associations
-------------------------------------------------------------------------------
No associations found.
Number of associations : 3
===============================================================================
A:active#
ANCP Policy Field Descriptions describes subscriber management ANCP policy fields.
Field |
Description |
---|---|
I. Rate Reduction |
The ingress rate reduction applied for this policy |
I. Rate Adjustment |
The ingress rate adjustment percentage |
I. Rate Monitor |
The ingress rate monitor rate |
I. Rate Monitor Alarm |
The ingress rate monitor enabled; yes or no |
I. Rate Modify |
The ingress rate modify scheduler policy |
E. Rate Reduction |
The egress rate reduction applied for this policy percentage |
E. Rate Adjustment |
The egress rate adjustment |
E. Rate Monitor |
The egress rate monitor rate |
E. Rate Monitor Alarm |
The egress rate monitor enabled; yes or no |
E. Rate Modify |
The egress rate monitor rate |
Port Down |
The actions taken on port-down |
Last Mgmt Change |
The time of the last modification of this entry |
SAP |
The ANCP static map entry SAP ID |
Svc-id |
The service ID associated with this static map |
String |
The ANCP string |
Cust-id |
The ID of the customer in which the multi-service-site specifies |
MSS-name |
The name of the multi-service-site used by this subscriber |
Number of associations |
The total number associations matching the search criteria |
ancp-string
ancp-string
Syntax
ancp-string
ancp-string ancp-string
ancp-string customer customer-id site customer-site-name
ancp-string sap sap-id
Context
[Tree] (show>subscriber-management ancp-string)
Full Context
show subscriber-mgmt ancp-string
Description
This command displays subscriber ANCP string information.
Parameters
- ancp-string
-
Specify the ASCII representation of the DSLAM circuit-id name.
- customer-id
-
Specify the associated existing customer name.
- customer-site-name
-
Specify the associated customer’s configured MSS name.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management ANCP string information.
Output ExampleA:active# show subscriber-mgmt ancp-string
===============================================================================
ANCP-Strings
===============================================================================
ANCP-String Assoc State
-------------------------------------------------------------------------------
"ANCP-String-1" SAP Up
"ANCP-String-2" SAP Down
"ANCP-String-3" MSS Up
"ANCP-String-4" MSS Unknown
"ANCP-String-5" ANCP Up
"ANCP-String-6" MSS Unknown
-------------------------------------------------------------------------------
Number of ANCP-Strings : 6
===============================================================================
A:active#
*A:Dut-C# show subscriber-mgmt ancp-string hpolSub43
===============================================================================
ANCP-String "hpolSub43"
===============================================================================
Type : SUB - "hpolSub43"
State : Up Ancp Policy: ancpPol
I. Rate : 100 kbps E. Rate : 200 kbps
Adj I. Rate: N/A Adj E. Rate: 200 kbps
Act I. Rate: N/A Act E. Rate: 182 kbps
Service Id : 1 (VPRN)
Group : Alu
Neighbor : 10.100.100.1:49063
===============================================================================
*A:Dut-C#
Other applicable show command output:
A:active# show service id 333 sap 1/1/3 detail
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id : 333
SAP : 1/1/3 Encap : null
...
-------------------------------------------------------------------------------
ANCP Override
-------------------------------------------------------------------------------
Ing Sched Name: root
- PIR : 100 kbps
- String : "ANCP-String-1"
Egr Sched Name: root
- PIR : 100 kbps
- String : "ANCP-String-1"
-------------------------------------------------------------------------------
...
Dro. InProf : 0 0
Dro. OutProf : 0 0
===============================================================================
A:active#
A:active# show service customer 1 site mss1
===============================================================================
Customer 1
===============================================================================
Customer-ID : 1
Description : Default customer
...
-------------------------------------------------------------------------------
ANCP Override
-------------------------------------------------------------------------------
Egr Sched Name: root
- PIR : 90 kbps
- String : "ANCP-String-3"
-------------------------------------------------------------------------------
Service Association
-------------------------------------------------------------------------------
No Service Association Found.
===============================================================================
A:active#
ANCP String Field Descriptions describes ANCP string output fields.
Field |
Description |
---|---|
ANCP-String |
The ANCP string name |
Assoc |
The entity associated with the ANCP string |
State |
The state of the entity associated with the ANCP string |
Number of ANCP-Strings |
The number of ANCP strings matching the search criteria |
Type |
The location the ANCP string is configured |
Ancp Policy |
The ANCP policy name |
I. Rate |
The ingress rate |
E. Rate |
The egress rate |
Adj I. Rate |
The adjusted ingress rate |
Adj E. Rate |
The adjusted egress rate |
Act I. Rate |
The actual ingress rate |
Act E. Rate |
The actual egress rate |
Service Id |
The service ID |
Group |
The group name |
Neighbor |
The neighbor address |
anycast
anycast
Syntax
anycast [family] [detail]
Context
[Tree] (show>router>pim anycast)
Full Context
show router pim anycast
Description
This command displays PIM anycast rp-set information.
Parameters
- family
-
Specifies the address family.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of a PIM anycast configuration.
Output ExampleA:dut-d# show router pim anycast
===================================================
PIM Anycast RP Entries
===================================================
Anycast RP Anycast RP Peer
---------------------------------------------------
100.100.100.1 10.102.1.1
10.103.1.1
10.104.1.1
---------------------------------------------------
PIM Anycast RP Entries : 3
===================================================
PIM Anycast Fields provides PIM anycast field descriptions
Label |
Description |
---|---|
Anycast Address |
Displays the candidate anycast address. |
Anycast RP Peer |
Displays the candidate anycast RP peer address. |
anysec
anysec
Syntax
anysec port port-id
Context
[Tree] (tools>dump anysec)
Full Context
tools dump anysec
Description
This command dumps ANYsec information.
Parameters
- port-id
-
Specifies the port ID.
Platforms
7750 SR-1-24D, 7750 SR-1-46S, 7750 SR-1-48D, 7750 SR-1-92S, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-1se
anysec
Syntax
anysec encryption-group group-name peer ip-address statistics
Context
[Tree] (clear anysec)
Full Context
clear anysec
Description
This command clears ANYsec statistics.
Parameters
- group-name
-
Specifies the encryption group name, up to 32 characters.
- ip-address
-
Specifies a peer IP address.
- statistics
-
Keyword used to clear ANYsec statistics
Platforms
7750 SR-1-24D, 7750 SR-1-46S, 7750 SR-1-48D, 7750 SR-1-92S, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-1se
anysec
Syntax
anysec
Context
[Tree] (show anysec)
Full Context
show anysec
Description
This command displays ANYsec information.
Platforms
7750 SR-1-24D, 7750 SR-1-46S, 7750 SR-1-48D, 7750 SR-1-92S, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-1se
app-filter
app-filter
Syntax
app-filter [entry-id]
Context
[Tree] (show>app-assure>group>policy app-filter)
Full Context
show application-assurance group policy app-filter
Description
This command displays application-assurance policy filter information.
Parameters
- entry-id
-
Specifies an existing application filter entry.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
app-group
app-group
Syntax
app-group [app-group-name] count [detail]
app-group count top granularity [max-count max-count]
Context
[Tree] (show>app-assure>group>aa-sub app-group)
[Tree] (show>app-assure>group app-group)
Full Context
show application-assurance group aa-sub app-group
show application-assurance group app-group
Description
This command displays per-application-group statistics. System-wide statistics displayed account for all flows completed and the last internal snapshot of the active flows.
Parameters
- app-group-name
-
Displays information about the specified application group name.
- count
-
Displays the counters for the application group.
- detail
-
Displays detailed information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the app-group command information.
Output ExampleA:ALU>show>app-assure>group# app-group count
===============================================================================
App-group Statistics
===============================================================================
Application Group Disc Octets Packets Flows
-------------------------------------------------------------------------------
File Transfer 0% 0 0 0
Games 0% 3865532 4952 144
Infrastructure 0% 174524 1217 1177
Instant Messaging 0% 2979117 9930 97
Local Content 0% 10581539 10942 74
Mail 0% 57940 346 24
MultiMedia 0% 76911464 79417 198
NNTP 0% 0 0 0
Peer to Peer 0% 10903442 13901 485
Premium Partner 0% 0 0 0
Remote Connectivity 0% 0 0 0
Server 0% 1097 8 2
Suspect 72% 1012 11 11
Tunneling 0% 19872617 33989 204
Unknown 0% 5243395 27510 2648
Web 0% 82135303 91828 2152
-------------------------------------------------------------------------------
A:ALU>show>app-assure>group#
A:ALU>show>app-assure>group# app-group "MultiMedia" count detail
===============================================================================
App-group "MultiMedia" Statistics
===============================================================================
Application Group:
Type Octets Packets Flows
-------------------------------------------------------------------------------
MultiMedia:
Admitted from subscriber: 193605 1797 23
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 4835822 3366 23
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Total flow duration: 433 seconds
Terminated flows: 46
Short Duration flows: 36
Medium Duration flows: 10
Long Duration flows: 0
Active subscribers: 0
===============================================================================
A:ALU>show>app-assure>group#
app-group
Syntax
app-group [app-group-name]
Context
[Tree] (show>app-assure>group>policy app-group)
Full Context
show application-assurance group policy app-group
Description
This command displays application-assurance policy application group information.
Parameters
- app-group-name
-
Specifies the application group name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
app-group
Syntax
app-group [app-group-name] count
Context
[Tree] (show>app-assure>group>aa-sub>um app-group)
Full Context
show application-assurance group aa-sub usage-monitor app-group
Description
This command displays usage monitor statistics for the application group.
Parameters
- app-group-name
-
Specifies the application group name, up to 32 characters.
- count
-
Displays counters for the application group.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
app-group
Syntax
app-group [app-group-name] count [detail]
Context
[Tree] (tools>dump>app-assure>group>aa-sub app-group)
Full Context
tools dump application-assurance group aa-sub app-group
Description
This command displays per-subscriber per-app-group statistics.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
app-profile
app-profile
Syntax
app-profile [app-prof-name]
app-profile app-prof-name associations
Context
[Tree] (show app-assure group policy app-profile)
Full Context
show application-assurance group policy app-profile
Description
This command displays application-assurance policy application profile information.
Parameters
- app-prof-name
-
Specifies an existing application profile name.
- associations
-
Displays subscriber management associations.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
app-qos-policy
app-qos-policy
Syntax
app-qos-policy [entry-id]
app-qos-policy non-zero
Context
[Tree] (show>app-assure>group>policy app-qos-policy)
Full Context
show application-assurance group policy app-qos-policy
Description
This command displays application-assurance policy application QoS policy information.
Parameters
- entry-id
-
Specifies an existing application QoS policy entry id.
- non-zero
-
Selects only non-zero count entries.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
app-service-option
app-service-option
Syntax
app-service-option [characteristic-name]
Context
[Tree] (show>app-assure>group>policy app-service-option)
Full Context
show application-assurance group policy app-service-option
Description
This command displays application-assurance policy application service option information.
Parameters
- characteristic-name
-
Specifies the characteristic name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
application
application
Syntax
application [application-name] count [detail]
application count top granularity [max-count max-count]
Context
[Tree] (show>app-assure>group application)
[Tree] (show>app-assure>group>aa-sub application)
[Tree] (show>app-assure>group>aa-sub-study application)
Full Context
show application-assurance group application
show application-assurance group aa-sub application
show application-assurance group aa-sub-study application
Description
This command displays per-application statistics. The system-wide statistics displayed account for all flows completed and the last internal snapshot of the active flows.
Subscriber statistics are available for special-study subscribers and account for all completed and active flows at the moment of this statistics request.
Parameters
- application-name
-
Displays information about the specified application name.
- count
-
Displays counter information.
- detail
-
Displays detailed information.
- top
-
Displays counters sorted by granularity.
- granularity
-
Displays counters sorted by octets, packets, or floe. This is indicated by granularity.
- max-count
-
If the value is greater than 0, displays up to the indicated value of statistic rows. If 0, displays all.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the application command information.
Output ExampleA:ALU-ABC>show>app-assure>group# application count
===============================================================================
Application Statistics
===============================================================================
Application Disc Octets Packets Flows
-------------------------------------------------------------------------------
...
DHT 0% 0 0 0
DNS_53 0% 96781 627 627
DNS_Local 0% 0 0 0
DNS_Server 0% 276 3 3
DNS_Suspect 100% 736 8 8
FTP 0% 0 0 0
...
-------------------------------------------------------------------------------
A:ALU-ABC>show>app-assure>group#
A:ALU-ABC>show>app-assure>group# application "POP3" count detail
===============================================================================
Application "POP3" Statistics
===============================================================================
Application:
Type Octets Packets Flows
-------------------------------------------------------------------------------
POP3:
Admitted from subscriber: 14095 149 10
Denied from subscriber: 0 0 0
Active flows from subscriber: 0
Admitted to subscriber: 30707 128 10
Denied to subscriber: 0 0 0
Active flows to subscriber: 0
Total flow duration: 7 seconds
Terminated flows: 20
Active subscribers: 0
A:ALU-ABC>show>app-assure>group#
A:ALU>show>app-assure>group# application "HTTP_Video" count detail
===============================================================================
Application "HTTP_Video" Statistics
===============================================================================
Application:
Type Octets Packets Flows
-------------------------------------------------------------------------------
HTTP_Video:
Admitted from subscriber: 369528 5404 36
Denied from subscriber: 0 0 0
Active flows from subscriber: 1
Admitted to subscriber: 15387734 10629 36
Denied to subscriber: 0 0 0
Active flows to subscriber: 1
Total flow duration: 463 seconds
Terminated flows: 72
Short Duration flows: 66
Medium Duration flows: 6
Long Duration flows: 0
Active subscribers: 1
===============================================================================
A:ALU>show>app-assure>group#
application
Syntax
application [app-name]
Context
[Tree] (show>app-assure>group>policy application)
Full Context
show application-assurance group policy application
Description
This command displays application-assurance policy application information.
Parameters
- app-name
-
Specifies the application name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
application
Syntax
application [application-name] count
Context
[Tree] (show>app-assure>group>aa-sub>um application)
Full Context
show application-assurance group aa-sub usage-monitor application
Description
This command displays usage monitor statistics for the application.
Parameters
- application-name
-
Specifies the application name, up to 32 characters.
- count
-
Displays counters for the application.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
application
Syntax
application [application-name] count [detail]
Context
[Tree] (tools>dump>app-assure>group>aa-sub application)
Full Context
tools dump application-assurance group aa-sub application
Description
This command displays per-subscriber per-application statistics.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
application
Syntax
application [app-name] [{dscp | dot1p}]
Context
[Tree] (show>router>sgt-qos application)
Full Context
show router sgt-qos application
Description
This command displays application QoS settings.
Parameters
- app-name
-
Specifies the application.
- dscp
-
Specifies to show DSCP values only.
- dot1p
-
Specifies to show dot1p values only.
Platforms
All
Output
The following output is an example of SGT QoS application information.
Output ExampleA:ALA-A# show router sgt-qos application
===============================================================================
DSCP Application Values
===============================================================================
Application Configured DSCP Value Default DSCP Value(s)
-------------------------------------------------------------------------------
bgp none nc1
bmp none af41
call-trace none af41
cflowd none nc1
dhcp none nc1, af41, nc2
diameter none af41
dns none af41
ftp none af41
grpc none af41
gtp none nc2, nc1
http none af41
icmp none be, nc1
igmp none nc1
igmp-reporter none nc1
l2tp none nc1
ldp none nc1
mld none nc1
mpls-udp-return none nc1
msdp none nc1
mtrace2 none nc1
ndis none nc1, nc2
ntp none nc1
ospf none nc1
pcep none nc1
pim none nc1
ptp none nc1
radius none nc1
rip none nc1
rsvp none nc1
sflow none nc1
snmp none af41
snmp-notification none af41
srrp none nc1
ssh none af41
syslog none af41
tacplus none af41
telnet none af41
tftp none af41
traceroute none be
vrrp none nc1
===============================================================================
===============================================================================
Dot1p Application Values
===============================================================================
Application Configured Dot1p Value Default Dot1p Value
-------------------------------------------------------------------------------
arp none 7
isis none 7
pppoe none 7
===============================================================================
A:ALA-A#
Some applications have multiple DSCP default values depending on the context or service.
application-assurance
application-assurance
Syntax
application-assurance
Context
[Tree] (clear application-assurance)
Full Context
clear application-assurance
Description
This command clears application assurance commands.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
application-assurance
Syntax
application-assurance
Context
[Tree] (show application-assurance)
Full Context
show application-assurance
Description
Commands in this context display application assurance commands.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
application-assurance
Syntax
application-assurance
Context
[Tree] (tools>dump application-assurance)
Full Context
tools dump application-assurance
Description
Commands in this context dump application assurance information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
application-assurance-group
application-assurance-group
Syntax
application-assurance-group [aa-group-id [ load-balance [unassigned]]]
Context
[Tree] (show>isa application-assurance-group)
Full Context
show isa application-assurance-group
Description
This command displays ISA group information.
Parameters
- aa-group-id
-
Specifies the AA ISA group ID.
- load-balance
-
Specifies load balancing information.
- unassigned
-
Specifies load balancing unassigned aa-sub information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
Show Application Assurance Group Output Fields describes the show command output fields:
Label |
Description |
---|---|
ISA-AA Group Index |
Indicates the group number of this group of MDAs. |
Description |
|
Primary ISA-AA |
Displays the primary slot and card number and whether the status is up or down and is either active or standby. |
Backup ISA-AA |
Displays the backup slot and card number and whether the status is up or down and is either active or standby. The status should be up and standby. |
Last Active change |
Indicates the last time a successful change was performed. |
Admin State |
Displays the administrative state, up or down. |
Oper State |
Displays the operational state, up or down. |
Diverted FCs |
Displays the forwarding class to be diverted. |
Fail to mode |
Displays how traffic is handled when there are no available ISA-AA cards to handle the traffic, either failToWire or failToOpen. |
Partitions |
Indicates whether partitions are enabled or disabled within an ISA-AA group. When the value of this object is set to enabled, partitions can be created in the tmnxBsxAaGrpPartTable. |
Egress from subscriber |
|
Pool |
Displays the buffer pool as defined in TIMETRA-PORT-MIB::tmnxObjectAppPool for subscriber to network traffic egressing towards the ISA-AA MDA. |
Reserved Cbs |
Displays the percentage of the buffer pool reserved for high priority traffic for subscriber to network traffic egressing towards the ISA-AA MDA. |
Slope Policy |
Displays the policy as defined in TIMETRA-QOS-MIB::tSlopePolicyTable for subscriber to network traffic egressing towards the ISA-AA MDA. |
Queue Policy |
Displays the policy as defined in TIMETRA-QOS-MIB::tNetworkQueueTable for subscriber to network traffic egressing towards the ISA-AA MDA. |
Scheduler Policy |
Displays the policy as defined in TIMETRA-QOS-MIB::tSlopePolicyTable for network to subscriber traffic egressing towards the ISA-AA MDA |
Egress to subscriber |
|
Pool |
Displays the buffer pool as defined in TIMETRA-PORT-MIB::tmnxObjectAppPool for network to subscriber traffic egressing towards the ISA-AA MDA. |
Reserved Cbs |
Displays the percentage of the buffer pool reserved for high priority traffic for network to subscriber traffic egressing towards the ISA-AA MDA. |
Slope Policy |
Displays the policy as defined in TIMETRA-QOS-MIB::tSlopePolicyTable for network to subscriber traffic egressing towards the ISA-AA MDA. |
Queue Policy |
Displays the policy as defined in TIMETRA-QOS-MIB::tNetworkQueueTable for network to subscriber traffic egressing towards the ISA-AA MDA. |
Scheduler Policy |
Displays the policy as defined in TIMETRA-QOS-MIB::tSchedulerPolicyTable for network to subscriber traffic egressing towards the ISA-AA MDA. |
Overload Sub-quarantine |
Displays the overload quarantine state, up or down. |
Overload Cut Through |
Displays the overload cut through state, enabled or disabled. |
*A:Dut-A# show isa application-assurance-group 1
===============================================================================
ISA Application-assurance-groups
===============================================================================
ISA-AA Group Index : 1
Description : (Not Specified)
Subscriber Scale : residential
WLAN GW Group Index : N/A
Primary ISA-AA : 5/1 up/active
Backup ISA-AA : none
Minimum ISA Generation : 2
Last Active change : 04/06/2018 10:18:50
Admin State : Up
Oper State : Up
Diverted FCs : be l2
Fail to mode : fail-to-wire
Partitions : disabled
QoS
Egress from subscriber
Pool : default
Reserved Cbs : default
Slope Policy : aa_spol1
Queue Policy : aa_nqpolEgr
Scheduler Policy : aa_pspFrmSub
Egress to subscriber
Pool : default
Reserved Cbs : default
Slope Policy : aa_spol1
Queue Policy : aa_nqpolEgr
Scheduler Policy : aa_pspToSub
Capacity Cost
High Threshold : 4294967295
Low Threshold : 0
Overload Sub-quarantine : Down
Overload Cut Through : disabled
Transit Prefix
Max IPv4 entries : 0
Max IPv6 entries : 0
Max IPv6 remote entries : 0
HTTP Enrichment
Max Packet Size : 1500 octets
Shared Resources
TCP Advanced Functions : 100%
===============================================================================
A:ALU>show>isa#
*A:Dut-C>show isa application-assurance-group 1 load-balance
===============================================================================
ISA Application-assurance-group 1
===============================================================================
load-balance status : Complete
isa-capacity-cost-threshold : low 0
: high 4294967295
-------------------------------------------------------------------------------
capacity aa-sub aa-sub ip transit-prefix-entries
cost stats addresses ipv4 v4-rm ipv6 v6-rm
-------------------------------------------------------------------------------
1/2 4 4 8 3 0 0 0 0
3/1 3 3 6 1 0 0 0 0
Mda Limit n/a 1024 32768 16384 0 0 0 0
=============================================================================
aa-sub type count for group 1
=============================================================================
all esm esm-mac sap spoke-sdp transit
-----------------------------------------------------------------------------
1/2 4 1 3 0 0 0
3/1 3 2 1 0 0 0
Unassigned(*) 0 0 0 0 0 n/a**
-------------------------------------------------------------------------------
(*) Subscribers are not initially load balanced until configuration and
persistence files have been processed.
(**) For unassigned transits, refer to unassigned subscriber load-balance
screen for details.
-------------------------------------------------------------------------------
Last tools load-balance complete reason:
Tool never performed or last performed on another AA group
Subs moved : 0
Next sub : n/a
Service Id : n/a
===============================================================================
*A:Dut-C# show isa application-assurance-group 84 load-balance unassigned
===============================================================================
ISA Application-assurance-group 84 unassigned
===============================================================================
type SvcId aa-sub App-Profile
-------------------------------------------------------------------------------
esm 2 Sub1 Cost30
esm 50 Sub2 Cost31
sap 29 2/1/10:527 Cost29
sap 30 2/1/10:528 Cost29
sap 31 2/1/10:529 Cost29
sap 31 2/1/10:530 Cost29
sap 31 2/1/10:531 Cost29
sap 32 2/1/10:546 Cost29
sap 32 2/1/10:547 Cost29
sap 33 2/1/10:548 Cost29
spoke 201 199:10 Cost27
spoke 202 199:17 Cost10
spoke 202 199:18 Cost10
spoke 202 199:19 Cost10
esm-mac 100 Sub3-000102030405 Cost30
===============================================================================
*A:Dut-C#
applications
applications
Syntax
applications
Context
[Tree] (show>log applications)
Full Context
show log applications
Description
This command displays a list of all application names that can be used in event-control and filter commands.
Platforms
All
Output
The following output is an example of log application information.
Output Example*A:7950 XRS-20# show log applications
===================================
Log Event Application Names
===================================
Application Name
-----------------------------------
BGP
...
CHASSIS
...
IGMP
...
LDP
LI
...
MIRROR
...
MPLS
...
OSPF
PIM
...
PORT
...
SYSTEM
...
USER
...
VRTR
...
===================================
A:ALA-1#
applications
Syntax
applications [isa mda-id/esa-vm-id]
Context
[Tree] (tools>dump>app-assure>group>ipassist applications)
Full Context
tools dump application-assurance group ip-identification-assist applications
Description
This command dumps statistics showing the amount of traffic detected by IP identification assist for supported applications.
Parameters
- isa mda-id
-
Specifies the slot and MDA of the ISA in the format slot/mda.
- isa esa-vm-id
-
Specifies the ESA and ESA VM in the format esa-esa-id/vm-id.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
Use the following command to display statistics showing how much traffic is detected by the IP identification assist feature for supported applications.
tools dump application-assurance group 1:0 ip-identification-assist applications isa 1/1
Output
Example===============================================================================
Application-Assurance group 1:0 ip-identification-assist application statistics
===============================================================================
isa 1/1
--------------------------------------------------------------------------------
Application Name Detection flows packets octets
---------------------------------- ---------- ------------------------- ------------------------- -------------------------
"Apple" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 32 (100.0%) 43768 (100.0%) 39252130 (100.0%)
"Apple App Store and iTunes" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
"Apple Music" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
"Apple iCloud" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
"Facebook" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 84 (100.0%) 90580 (100.0%) 96430386 (100.0%)
"Google" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 382 (100.0%) 25980 (100.0%) 21150315 (100.0%)
"Google Play Store" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
"Instagram" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 52 (100.0%) 18714 (100.0%) 18655139 (100.0%)
"Netflix" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 78 (100.0%) 59059 (100.0%) 52961501 (100.0%)
"Snapchat" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
"Spotify" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 85 (100.0%) 35703 (100.0%) 32556052 (100.0%)
"Twitter" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 38 (100.0%) 20555 (100.0%) 16997835 (100.0%)
"Whats App" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
"YouTube" app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 6 (100.0%) 27562 (100.0%) 31582683 (100.0%)
---------------------------------- ---------- ------------------------- ------------------------- -------------------------
TOTAL (14 applications) app-filter 0 ( 0.0%) 0 ( 0.0%) 0 ( 0.0%)
ip-assist 757 (100.0%) 321921 (100.0%) 309586041 (100.0%)
===============================================================================
aps
aps
Syntax
aps [aps-id] [detail]
Context
[Tree] (show aps)
Full Context
show aps
Description
This command displays Automated Protection Switching (APS) information.
Parameters
- aps-id
-
Displays information for the specified APS group ID.
- detail
-
Displays detailed APS information.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
Output
See the following output examples:
*A:Dut-A# show aps aps-1
===============================================================================
APS Group Info
===============================================================================
Interface Admin Oper MC-Ctl Work Prot Active Tx/Rx
State State State Circuit Circuit Circuit K1 Byte
-------------------------------------------------------------------------------
aps-1 Up Up N/A 1/5/1 1/9/5 1/5/1 PC-Tx: No-Req
===============================================================================
*A:Dut-A#
*A:Dut-A# show aps aps-1 detail
===============================================================================
APS Group: aps-1
===============================================================================
Description : APS Group
Group Id : 1 Active Circuit : 1/5/1
Admin Status : Up Oper Status : Up
Working Circuit : 1/5/1 Protection Circuit : 1/9/5
Switching-mode : Uni-1plus1 Switching-arch : 1+1(sig,data)
Revertive-mode : Non-revertive Revert-time (min) :
Rx K1/K2 byte : 0x00/0x00 (No-Req on Protect)
Tx K1/K2 byte : 0x00/0x00 (No-Req on Protect)
Current APS Status : OK
Multi-Chassis APS : No
Neighbor : 0.0.0.0
Control link state : N/A
Advertise Interval : 1000 msec Hold Time : 3000 msec
APS SF Hold Time : 6000 msec APS SD Hold Time : 9000 msec
Mode mismatch Cnt : 0 Channel mismatch Cnt : 0
PSB failure Cnt : 0 FEPL failure Cnt : 0
-------------------------------------------------------------------------------
APS Working Circuit - 1/5/1
-------------------------------------------------------------------------------
Admin Status : Up Oper Status : Up
Current APS Status : OK No. of Switchovers : 0
Last Switchover : None Switchover seconds : 0
Signal Degrade Cnt : 1 Signal Failure Cnt : 1
Last Switch Cmd : No Cmd Last Exercise Result : Unknown
Tx L-AIS : None
-------------------------------------------------------------------------------
APS Protection Circuit - 1/9/5
-------------------------------------------------------------------------------
Admin Status : Up Oper Status : Up
Current APS Status : OK No. of Switchovers : 0
Last Switchover : None Switchover seconds : 0
Signal Degrade Cnt : 1 Signal Failure Cnt : 1
Last Switch Cmd : No Cmd Last Exercise Result : Unknown
Tx L-AIS : None
===============================================================================
*A:Dut-A#
Output Example: show aps (Protect MC-APS Node)
B:Dut-E# show aps
==================================================================================
APS Group Info
==================================================================================
Interface Admin Oper MC-Ctl Work Prot Active Tx/Rx
State State State Circuit Circuit Circuit K1 Byte
----------------------------------------------------------------------------------
aps-20 Up Up N/A 3/1/1 3/1/2 3/1/1 PC-Tx: No-Req
==================================================================================
B:Dut-E#
B:Dut-E# show aps aps-30 detail
===============================================================================
APS Group: aps-30
===============================================================================
Description : APS Group
Group Id : 30 Active Circuit : N/A
Admin Status : Up Oper Status : Up
Working Circuit : N/A Protection Circuit : 2/2/2
Switching-mode : Bi-directional Switching-arch : 1+1
Revertive-mode : Non-revertive Revert-time (min) :
Rx K1/K2 byte : 0x00/0x05 (No-Req on Protect)
Tx K1/K2 byte : 0x00/0x05 (No-Req on Protect)
Current APS Status : OK
Multi-Chassis APS : Yes
Neighbor : 10.1.1.1
Control link state : Up
Advertise Interval : 1000 msec Hold time : 3000 msec
Mode mismatch Cnt : 0 Channel mismatch Cnt : 0
PSB failure Cnt : 0 FEPL failure Cnt : 1
-------------------------------------------------------------------------------
APS Working Circuit - Neighbor
-------------------------------------------------------------------------------
Admin Status : N/A Oper Status : N/A
Current APS Status : OK No. of Switchovers : 0
Last Switchover : None Switchover seconds : 0
Signal Degrade Cnt : 0 Signal Failure Cnt : 0
Last Switch Cmd : No Cmd Last Exercise Result : Unknown
Tx L-AIS : None
-------------------------------------------------------------------------------
APS Protection Circuit - 2/2/2
-------------------------------------------------------------------------------
Admin Status : Up Oper Status : Up
Current APS Status : OK No. of Switchovers : 0
Last Switchover : None Switchover seconds : 0
Signal Degrade Cnt : 0 Signal Failure Cnt : 0
Last Switch Cmd : No Cmd Last Exercise Result : Unknown
Tx L-AIS : None
===============================================================================
B:Dut-E#
Output Fields: show aps
Output Fields: show aps describes output fields for the show aps command.
Label |
Description |
---|---|
Interface |
Specifies the APS interface name (the APS group port). |
Admin State |
Up — APS is administratively up. Down — APS port is administratively down. |
Oper State |
Up — APS port is operationally up. Down — APS is operationally down. |
MC-CTL State |
Specifies the multi-chassis state. |
Work Circuit |
Specifies the working circuit ID. |
Prot Circuit |
Specifies the physical port that acts as the protection circuit for this APS group. |
Active Circuit |
Specifies the active circuit. |
Tx/Rx K1 Byte |
Displays the value of the SONET/SDH K1 byte received or transmitted on the protection circuit. |
Group Id |
Displays the APS group name. |
Protection Circuit |
Displays the physical port that will act as the protection circuit for this APS group. |
Switching-mode |
Displays the switching mode of the APS group. |
Switching-arch |
The architecture of the APS group. |
Revertive-mode |
Displays the revertive mode of the APS group. non-revertive — Traffic remains on the protection line until another switch request is received. revertive — When the condition that caused a switch to the protection line has been cleared the signal is switched back to the working line. |
Revert-time |
Displays the configured time, in minutes, to wait after the working circuit has become functional again, before making the working circuit active again. If the revertive mode is non-revertive, then this field will be empty. |
Rx K1/K2 byte |
Displays the value of the SONET/SDH K1/K2 byte received on the interface. |
Tx K1/K2 byte |
Displays the value of the SONET/SDH K1/K2 byte transmitted on the interface. |
Current APS Status |
Displays the current APS status. |
Mode Mismatch Cnt |
Indicates the number of times a conflict occurs between the current local mode and the received K2 mode information. |
Channel mismatch Cnt |
Indicates the number of mismatches between the transmitted K1 channel and the received K2 channel has been detected. |
PSB failure Cnt |
Displays a count of Protection Switch Byte (PSB) failure conditions. This condition occurs when either an inconsistent APS byte or an invalid code is detected. |
FEPL failure Cnt |
Displays a count of far-end protection-line (FEPL) failure conditions. This condition is declared based on receiving SF on the protection line in the K1 byte. |
No. of Switchovers |
Displays the number of times a switchover has occurred. |
Last Switchover |
Displays the time stamp of the last switchover. |
Switchover seconds |
Displays the cumulative Protection Switching Duration (PSD) time in seconds. For a working channel, this is the cumulative number of seconds that service was carried on the protection line. For the protection line, this is the cumulative number of seconds that the protection line has been used to carry any working channel traffic. This information is only valid if revertive switching is enabled. |
Signal Degrade Cnt |
Displays the number of times the signal was degraded. |
Signal Failure Cnt |
Displays the number of times the signal failed. |
Last Switch Cmd |
Reports the last switch command that was performed on a circuit. |
Last Exercise Result |
The result of the last exercise request on a circuit. |
Neighbor address |
Displays the neighbor IP address. |
Advertise Interval |
Displays the advertise interval. |
Hold time |
Displays the hold time. |
aps
Syntax
aps aps-id [clear]
aps mc-aps-signaling [clear]
aps mc-aps-ppp [clear]
Context
[Tree] (tools>dump aps)
Full Context
tools dump aps
Description
This command displays Automated Protection Switching (APS) information.
Parameters
- aps-id
-
Specifies the APS ID.
- clear
-
Removes all Automated Protection Switching (APS) operational commands.
- mc-aps-signaling
-
Displays multi-chassis APS signaling information.
- mc-aps-ppp
-
Displays multi-chassis APS PPP information.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
Output
The following output is an example of APS information.
Output Example*A:AS_SR7_2# tools dump aps aps-33
GrpId = 33, state = Running, mode:cfg/oper = Bi-directional/Bi-directional
revert = 0, workPort: N/A, protPort: 2/1/1, activePort: working
rxK1 = 0x0 (No-Req on Protect), physRxK1 = 0x0, rxK2 = 0x5
txK1 = 0x0 (No-Req on Protect), physTxK1 = 0x0, txK2 = 0x5
K1ReqToBeTxed = 0x0, K1ChanToBeTxed = 0x0, lastRxReq = 0xc
MC-APS Nbr = 10.100.100.1 (Up), advIntvl = 10, hold = 30
workPort: status = OK, Tx-Lais = None, sdCnt = 1, sfCnt = 1
numSwitched = 1, switchSecs = 0, lastSwitched = 07/25/2007 08:00:12
disCntTime = , alarms = , switchCmd = No Cmd
protPort: status = OK, Tx-Lais = None, sdCnt = 1, sfCnt = 0
numSwitched = 1, switchSecs = 0, lastSwitched = 07/25/2007 08:03:39
disCntTime = , alarms = , switchCmd = No Cmd
GrpStatus: OK, mmCnt = 1, cmCnt = 1, psbfCnt = 1, feplfCnt = 2
LocalSwitchCmd: priority = No-Req, portNum = 0
RemoteSwitchCmd: priority = No-Req, portNum = 0
Running Timers = mcAdvIntvl mcHold
processFlag = apsFailures = , sonet = Y
DebugInfo: dmEv = 0, dmClrEv = 0, amEv = 1, amClrEv = 1
cmEv = 1, cmClrEv = 1, psbfEv = 1, psbfClrEv = 1
feplfEv = 2, feplfClrEv = 2, wtrEv = 0, psbfDetectEv = 0
wSdEv = 1, wSfEv = 2, pSdEv = 1, pSfEv = 1
portStatusEv = 8, rxK1Ev = 9, txLaisEv = 2, lastEvName = FeplClr
CtlUpEv = 3, CtlDnEv = 2, wAct = 0, wDeAct = 0
Seq Event TxK1/K2 RxK1/K2 Dir Active Time
=== ======= ======= ======= ===== ====== ================
000 ProtAdd 0xc005 0x0000 Tx--> Work 497 02:18:10.590
001 RxKByte 0xc005 0x6dea Rx<-- Work 497 02:20:14.820
002 RxKByte 0xc005 0xc005 Rx<-- Work 497 02:21:30.970
003 RxKByte 0xc005 0x2005 Rx<-- Work 497 02:21:36.530
004 pSFClr 0x0005 0x2005 Tx--> Work 497 02:21:40.590
005 RxKByte 0x0005 0x0005 Rx<-- Work 497 02:21:40.600
006 RxKByte 0x0005 0xc115 Rx<-- Work 497 02:25:22.840
007 RxKByte 0x2115 0xc115 Tx--> Prot 497 02:25:22.840
008 RxKByte 0x2115 0xa115 Rx<-- Prot 000 00:00:47.070
009 RxKByte 0x2115 0x1115 Rx<-- Prot 000 00:00:47.560
010 RxKByte 0x2115 0xc005 Rx<-- Prot 000 00:00:57.010
011 RxKByte 0x2005 0xc005 Tx--> Work 000 00:00:57.010
012 RxKByte 0x2005 0x0005 Rx<-- Work 000 00:01:06.170
013 RxKByte 0x0005 0x0005 Tx--> Work 000 00:01:06.170
Output Example
:AS_SR7_1# tools dump aps mc-aps-ppp
pppmMcsModStarted = Yes
pppmMcsDbgDoSync = Yes
pppmMcsApsGrpHaAuditDone = Yes
pppmMcsPostHaSyncedApsGrpId = 47
pppmMcsMcApsChanCnt = 1280
pppmMcsDbgRxPktCnt = 2560
pppmMcsDbgRxPktNotProcessedCnt = 0
pppmMcsDbgRxPktInvalidCnt = 0
pppmMcsDbgInconsistentRxPktDropCnt = 0
pppmMcsDbgInconsistentTxPktDropCnt = 1176
pppmMcsDbgTxPktNotSentCnt = 0
pppmMcsDbgTxPktSentCnt = 25
pppmMcsDbgEvtDropCnt = 0
pppmMcsDbgMemAllocErrCnt = 0
pppmMcsDbgReTxCnt = 0
pppmMcsDbgReTxExpCnt = 0
pppmMcsDbgReReqCnt = 0
pppmMcsStateAckQueueCnt (curr/peek) = 0/130
pppmMcsStateReqQueueCnt (curr/peek) = 0/1280
pppmMcsStateReReqQueueCnt (curr/peek) = 0/256
pppmMcsStateTxQueueCnt (curr/peek) = 0/512
pppmMcsStateReTxQueueCnt (curr/peek) = 0/130
MC-APS Peer Info :
--------------------
Grp 13 Addr 10.100.100.2 - Up
Grp 20 Addr 10.100.100.2 - Up
Grp 35 Addr 10.100.100.2 - Up
Grp 43 Addr 10.100.100.2 - Up
Grp 47 Addr 10.100.100.2 - Up
Number of pppmMcs Evt Msgs dispatched:
ctl_link_state : 0
ctl_link_up_tmr : 0
ctl_link_down_tmr : 0
ha_audit_done : 0
Output Example
*A:eth_aps_sr7# tools dump aps mc-aps-signaling
MC-APS Control Debug Counters :
-------------------------------
Ctl Pkt Rx = 0
Invalid Rx Ctl Pkt = 0
Incompatible Rx Ctl Pkt = 0
Nbr not Rx Ctl Pkt = 0
Invalid Rx Ctl Pkt Tlv = 0
Ctl Pkt Rx-ed before HaReady = 0
Not sent Tx Ctl Pkt = 0
MC-APS-LAG Debug Counters :
---------------------------
Ctl Pkt Rx from IOM = 0
Not processed Rx Ctl Pkt = 0
Invalid Rx Ctl Pkt = 0
Incompatible Rx Ctl Pkt = 0
Rx Ctl Pkt queueing failed = 0
Ctl Pkt Tx (direct) = 0
Ctl Pkt Tx (UDP socket) = 0
Not sent Tx Ctl Pkt = 0
Route Update = 0
Matched Route Update = 0
Msg Buf Alloc Failed = 0
MC-APS-LAG NbrRoute Entries :
-------------------------------
NbrAddr 10.1.1.1 NextHopAddr ::
EgressIfIndex = 0
EgressPortId = Unknown
app refCnt = 1
refCntTotal = 1
aps
Syntax
aps
Context
[Tree] (tools>perform aps)
Full Context
tools perform aps
Description
Commands in this context perform Automated Protection Switching (APS) operations.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
arbiter-stats
arbiter-stats
Syntax
arbiter-stats
Context
[Tree] (clear>qos arbiter-stats)
Full Context
clear qos arbiter-stats
Description
Commands in this context clear arbiter statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
arbiter-stats
Syntax
arbiter-stats
Context
[Tree] (monitor>qos arbiter-stats)
Full Context
monitor qos arbiter-stats
Description
Commands in this context configure monitor functionality for arbiter statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
arbiter-stats
Syntax
arbiter-stats
Context
[Tree] (show>qos arbiter-stats)
Full Context
show qos arbiter-stats
Description
Commands in this context display arbiter statistics information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
area
area
Syntax
area [area-id] [detail] [ lfa]
area [area-id] [detail] lfa flex-algo flex-algo-id
area [area-id] [detail] lfa flex-algo all
Context
[Tree] (show>router>ospf area)
Full Context
show router ospf area
Description
This command displays configuration information about all areas or the specified area.
Parameters
- area-id
-
Displays the OSPF area ID expressed in dotted decimal notation or as a 32-bit decimal integer.
- flex-algo-id
-
Displays the flexible algorithm identifier.
- detail
-
Displays detailed operational and statistical information about the specified area.
- lfa
-
Displays Loop-Free Alternate (LFA) next-hop information. This information corresponds to the backup next hops for IP links and nodes written in RTM by the base LFA feature.
- flex-algo
-
Displays OSPFv2 information for the specified algorithm identifier.
- flex-algo all
-
Displays OSPFv2 information for all flexible algorithms.
Platforms
All
Output
The following outputs are examples of OSPF area outputs.
OSPF Area Output Fields describes the standard and detailed command output fields for an OSPF area.
Label |
Description |
---|---|
Area Id |
A 32 bit integer uniquely identifying an area. |
Type |
NSSA — This area is configured as an NSSA area. Standard — This area is configured as a standard area (not NSSA or Stub). Stub — This area is configured as a stub area. |
SPF Runs |
The number of times that the intra-area route table has been calculated using this area’s link state database. |
LSA Count |
The total number of link-state advertisements in this area’s link state database, excluding AS External LSAs. |
LSA Cksum Sum |
The 32-bit unsigned sum of the link-state database advertisements LS checksums contained in this area’s link state database. This checksum excludes AS External LSAs (type-5). |
No. of OSPF Areas |
The number of areas configured on the router. |
Virtual Links |
The number of virtual links configured through this transit area. |
Active IFs |
The active number of interfaces configured in this area. |
Area Bdr Rtrs |
The total number of ABRs reachable within this area. |
AS Bdr Rtrs |
The total number of ASBRs reachable within this area. |
Last SPF Run |
The time when the last intra-area SPF was run on this area. |
Router LSAs |
The total number of router LSAs in this area. |
Network LSAs |
The total number of network LSAs in this area. |
Summary LSAs |
The summary of LSAs in this area. |
Asbr-summ LSAs |
The summary of ASBR LSAs in this area. |
Nssa-ext LSAs |
The total number of NSSA-EXT LSAs in this area. |
Area opaque LSAs |
The total number of opaque LSAs in this area. |
Total Nbrs |
The total number of neighbors in this area. |
Total IFs |
The total number of interfaces configured in this area. |
Total LSAs |
The sum of LSAs in this area excluding autonomous system external LSAs. |
Blackhole Range |
False — No blackhole route is installed for aggregates configured in this area. True — A lowest priority blackhole route is installed for aggregates configured in this area. |
Export Database |
False — The extended TE Database (TE-DB) is not exported in this area. True — The extended TE Database (TE-DB) is exported in this area. |
Export Policies |
The export policies configured in this area. |
Export Fltrd LSAs |
The total number of LSAs filtered by area export policies. |
Import Policies |
The import policies configured in this area. |
Import Fltrd LSAs |
The total number of LSAs filtered by area import policies. |
A:SetupCLI# show router ospf 0 area detail
===============================================================================
Rtr Base OSPFv2 Instance 0 Areas (detail)
===============================================================================
-------------------------------------------------------------------------------
Area Id: 0.0.0.0
-------------------------------------------------------------------------------
Area Id : 0.0.0.0 Type : Standard
Key Rollover Int.: 10 LFA : Include
Virtual Links : 0 Total Nbrs : 0
Active IFs : 0 Total IFs : 2
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 0 Last SPF Run : Never
Router LSAs : 0 Network LSAs : 0
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 1
Total LSAs : 1 LSA Cksum Sum : 0xd6af
Blackhole Range : False Unknown LSAs : 0
Export Database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
-------------------------------------------------------------------------------
Area Id: 1.1.1.1
-------------------------------------------------------------------------------
Area Id : 1.1.1.1 Type : Stub
Default Cost : 16777215 Import Summary : Send Summary
Key Rollover Int.: 10 LFA : Exclude
Virtual Links : 0 Total Nbrs : 0
Active IFs : 0 Total IFs : 1
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 0 Last SPF Run : Never
Router LSAs : 0 Network LSAs : 0
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 1
Total LSAs : 1 LSA Cksum Sum : 0xf493
Blackhole Range : False Unknown LSAs : 0
Export database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
-------------------------------------------------------------------------------
Area Id: 2.2.2.2
-------------------------------------------------------------------------------
Area Id : 2.2.2.2 Type : Standard
Key Rollover Int.: 10 LFA : Include
Virtual Links : 1 Total Nbrs : 0
Active IFs : 0 Total IFs : 0
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 0 Last SPF Run : Never
Router LSAs : 0 Network LSAs : 0
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 1
Total LSAs : 1 LSA Cksum Sum : 0xd6af
Blackhole Range : True Unknown LSAs : 0
Export database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
===============================================================================
A:SetupCLI#
*A:Dut-B# show router ospf area 0.0.0.0 detail
===============================================================================
Rtr Base OSPFv2 Instance 0 Area 0.0.0.0 (detail)
===============================================================================
-------------------------------------------------------------------------------
Configuration
-------------------------------------------------------------------------------
Area Id : 0.0.0.0 Type : Standard
-------------------------------------------------------------------------------
Statistics
-------------------------------------------------------------------------------
Virtual Links : 0 Total Nbrs : 2
Active IFs : 3 Total IFs : 3
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 7 Last SPF Run : 10/26/2006 10:09:18
Router LSAs : 3 Network LSAs : 3
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 3
Total LSAs : 9 LSA Cksum Sum : 0x28b62
Blackhole Range : True Unknown LSAs : 0
Export database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
===============================================================================
*A:Dut-B# show router ospf 0 area 0.0.0.0 lfa
=======================================================================
Rtr Base OSPFv2 Instance 0 Path Table
=======================================================================
Node Interface Nexthop
LFA Interface LFA Nexthop
-----------------------------------------------------------------------
10.20.1.1 to_Dut-A1 10.20.1.1
to_Dut-C1 10.20.1.3
10.20.1.3 to_Dut-C1 10.20.1.3
to_Dut-A1 10.20.1.1
10.20.1.4 to_Dut-D1 10.20.1.4
10.20.1.6 to_Dut-D1 10.20.1.4
to_Dut-C1 10.20.1.3
=======================================================================
*A:Dut-B#
*A:Dut-B# show router ospf 0 area 0.0.0.0 lfa detail
=======================================================================
Rtr Base OSPFv2 Instance 0 Path Table (detail)
=======================================================================
OSPF Area : 0.0.0.0
-----------------------------------------------------------------------
Node : 10.20.1.1 Metric : 10
Interface : to_Dut-A1 Nexthop : 10.20.1.1
LFA Interface : to_Dut-C1 LFA Metric : 20
LFA type : linkProtection LFA Nexthop : 10.20.1.3
Node : 10.20.1.3 Metric : 10
Interface : to_Dut-C1 Nexthop : 10.20.1.3
LFA Interface : to_Dut-A1 LFA Metric : 20
LFA type : linkProtection LFA Nexthop : 10.20.1.1
Node : 10.20.1.4 Metric : 10
Interface : to_Dut-D1 Nexthop : 10.20.1.4
Node : 10.20.1.6 Metric : 20
Interface : to_Dut-D1 Nexthop : 10.20.1.4
LFA Interface : to_Dut-C1 LFA Metric : 30
LFA type : nodeProtection LFA Nexthop : 10.20.1.3
=======================================================================
*A:Dut-B#
Output Example: show router ospf area lfa
flex-algo
*A:Dut-C# show router ospf area lfa flex-algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Flex-Algo 128 Path Table
===============================================================================
10.20.1.2 C1/1/5-B1/1/8 10.20.1.2
C1/1/7-E1/1/1 10.20.1.5
10.20.1.5 C1/1/7-E1/1/1 10.20.1.5
C1/1/5-B1/1/8 10.20.1.2
===============================================================================
*A:Dut-C#
area
Syntax
area [area-id] [detail] [ lfa]
Context
[Tree] (show>router>ospf3 area)
Full Context
show router ospf3 area
Description
This command displays configuration information about all areas or the specified area. When detail is specified operational and statistical information will be displayed.
Parameters
- area-id
-
Displays the OSPF area ID expressed in dotted decimal notation or as a 32-bit decimal integer.
- detail
-
Displays detailed information about the specified area.
- lfa
-
Displays Loop-Free Alternate (LFA) next-hop information. This information corresponds to the backup next hops for IP links and nodes written in RTM by the base LFA feature.
Platforms
All
Output
OSPF Area Output
The following table describes the standard and detailed command output fields for an OSPF area.
Label |
Description |
---|---|
Area Id |
A 32 bit integer uniquely identifying an area. |
Type |
NSSA — This area is configured as an NSSA area. Standard — This area is configured as a standard area (not NSSA or Stub). Stub — This area is configured as a stub area. |
SPF Runs |
The number of times that the intra-area route table has been calculated using this area’s link state database. |
LSA Count |
The total number of link-state advertisements in this area’s link state database, excluding AS External LSAs. |
LSA Cksum Sum |
The 32-bit unsigned sum of the link-state database advertisements LS checksums contained in this area’s link state database. This checksum excludes AS External LSAs (type-5). |
No. of OSPF Areas |
The number of areas configured on the router. |
Virtual Links |
The number of virtual links configured through this transit area. |
Active IFs |
The active number of interfaces configured in this area. |
Area Bdr Rtrs |
The total number of ABRs reachable within this area. |
AS Bdr Rtrs |
The total number of ASBRs reachable within this area. |
Last SPF Run |
The time when the last intra-area SPF was run on this area. |
Router LSAs |
The total number of router LSAs in this area. |
Network LSAs |
The total number of network LSAs in this area. |
Summary LSAs |
The summary of LSAs in this area. |
Asbr-summ LSAs |
The summary of ASBR LSAs in this area. |
Nssa-ext LSAs |
The total number of NSSA-EXT LSAs in this area. |
Area opaque LSAs |
The total number of opaque LSAs in this area. |
Total Nbrs |
The total number of neighbors in this area. |
Total IFs |
The total number of interfaces configured in this area. |
Total LSAs |
The sum of LSAs in this area excluding autonomous system external LSAs. |
Blackhole Range |
False — No blackhole route is installed for aggregates configured in this area. True — A lowest priority blackhole route is installed for aggregates configured in this area. |
Export Database |
False — The extended TE Database (TE-DB) is not exported in this area. True — The extended TE Database (TE-DB) is exported in this area. |
Export Policies |
The export policies configured in this area. |
Export Fltrd LSAs |
The total number of LSAs filtered by area export policies. |
Import Policies |
The import policies configured in this area. |
Import Fltrd LSAs |
The total number of LSAs filtered by area import policies. |
A:SetupCLI# show router ospf 0 area detail
===============================================================================
Rtr Base OSPFv2 Instance 0 Areas (detail)
===============================================================================
-------------------------------------------------------------------------------
Area Id: 0.0.0.0
-------------------------------------------------------------------------------
Area Id : 0.0.0.0 Type : Standard
Key Rollover Int.: 10 LFA : Include
Virtual Links : 0 Total Nbrs : 0
Active IFs : 0 Total IFs : 2
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 0 Last SPF Run : Never
Router LSAs : 0 Network LSAs : 0
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 1
Total LSAs : 1 LSA Cksum Sum : 0xd6af
Blackhole Range : False Unknown LSAs : 0
Export Database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
-------------------------------------------------------------------------------
Area Id: 1.1.1.1
-------------------------------------------------------------------------------
Area Id : 1.1.1.1 Type : Stub
Default Cost : 16777215 Import Summary : Send Summary
Key Rollover Int.: 10 LFA : Exclude
Virtual Links : 0 Total Nbrs : 0
Active IFs : 0 Total IFs : 1
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 0 Last SPF Run : Never
Router LSAs : 0 Network LSAs : 0
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 1
Total LSAs : 1 LSA Cksum Sum : 0xf493
Blackhole Range : False Unknown LSAs : 0
Export database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
-------------------------------------------------------------------------------
Area Id: 2.2.2.2
-------------------------------------------------------------------------------
Area Id : 2.2.2.2 Type : Standard
Key Rollover Int.: 10 LFA : Include
Virtual Links : 1 Total Nbrs : 0
Active IFs : 0 Total IFs : 0
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 0 Last SPF Run : Never
Router LSAs : 0 Network LSAs : 0
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 1
Total LSAs : 1 LSA Cksum Sum : 0xd6af
Blackhole Range : True Unknown LSAs : 0
Export database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
===============================================================================
A:SetupCLI#
*A:Dut-B# show router ospf area 0.0.0.0 detail
===============================================================================
Rtr Base OSPFv2 Instance 0 Area 0.0.0.0 (detail)
===============================================================================
-------------------------------------------------------------------------------
Configuration
-------------------------------------------------------------------------------
Area Id : 0.0.0.0 Type : Standard
-------------------------------------------------------------------------------
Statistics
-------------------------------------------------------------------------------
Virtual Links : 0 Total Nbrs : 2
Active IFs : 3 Total IFs : 3
Area Bdr Rtrs : 0 AS Bdr Rtrs : 0
SPF Runs : 7 Last SPF Run : 10/26/2006 10:09:18
Router LSAs : 3 Network LSAs : 3
Summary LSAs : 0 Asbr-summ LSAs : 0
Nssa ext LSAs : 0 Area opaque LSAs : 3
Total LSAs : 9 LSA Cksum Sum : 0x28b62
Blackhole Range : True Unknown LSAs : 0
Export database : False
Export Policies : None
Export Fltrd LSAs: 0
Import Policies : None
Import Fltrd LSAs: 0
===============================================================================
*A:Dut-B# show router ospf 0 area 0.0.0.0 lfa
=======================================================================
Rtr Base OSPFv2 Instance 0 Path Table
=======================================================================
Node Interface Nexthop
LFA Interface LFA Nexthop
-----------------------------------------------------------------------
10.20.1.1 to_Dut-A1 10.20.1.1
to_Dut-C1 10.20.1.3
10.20.1.3 to_Dut-C1 10.20.1.3
to_Dut-A1 10.20.1.1
10.20.1.4 to_Dut-D1 10.20.1.4
10.20.1.6 to_Dut-D1 10.20.1.4
to_Dut-C1 10.20.1.3
=======================================================================
*A:Dut-B#
*A:Dut-B# show router ospf 0 area 0.0.0.0 lfa detail
=======================================================================
Rtr Base OSPFv2 Instance 0 Path Table (detail)
=======================================================================
OSPF Area : 0.0.0.0
-----------------------------------------------------------------------
Node : 10.20.1.1 Metric : 10
Interface : to_Dut-A1 Nexthop : 10.20.1.1
LFA Interface : to_Dut-C1 LFA Metric : 20
LFA type : linkProtection LFA Nexthop : 10.20.1.3
Node : 10.20.1.3 Metric : 10
Interface : to_Dut-C1 Nexthop : 10.20.1.3
LFA Interface : to_Dut-A1 LFA Metric : 20
LFA type : linkProtection LFA Nexthop : 10.20.1.1
Node : 10.20.1.4 Metric : 10
Interface : to_Dut-D1 Nexthop : 10.20.1.4
Node : 10.20.1.6 Metric : 20
Interface : to_Dut-D1 Nexthop : 10.20.1.4
LFA Interface : to_Dut-C1 LFA Metric : 30
LFA type : nodeProtection LFA Nexthop : 10.20.1.3
=======================================================================
*A:Dut-B#
arp
arp
Syntax
arp {[ip-address] | [mac ieee-address] | [ sap sap-id] | [interface ip-int-name] | [ sdp sdp-id:vc-id] | [summary] }
Context
[Tree] (show>service>id arp)
Full Context
show service id arp
Description
This command displays the ARP cache entries for this service.
Parameters
- ip-address
-
Specifies the IP address in IP address dotted decimal notation.
- ieee-mac-address
-
Specifies the 48-bit MAC address in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.
- sap-id
-
Specifies a Service Access Point (SAP) within a service.
- ip-int-name
-
Specifies the name of the IP interface. Interface names can be from 1 to 32 alphanumeric characters. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed between double quotes.
- sdp-id
-
Specifies the SDP identifier. Allowed values are integers in the range of 1 and 17407 for existing SDPs.
- vc-id
-
Specifies the virtual circuit identifier.
Platforms
All
Output
The following output is an example of service ID information. Service-ID ARP Field Descriptions describes the output fields.
Output ExampleA:ALA-A# show service id 100 base
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Type Age Interface Port
-------------------------------------------------------------------------------
10.1.0.1 00:00:66:66:66:01 Other 00h00m00s ies-10-101.1.0.1 1/1/4
239.1.1.2 00:00:5e:00:01:64 Other 00h00m00s ies-10-239.1.1.2 1/1/3
239.1.1.201 00:00:22:2e:a5:61 Static 00h00m00s ies-10-239.1.1.2 1/1/3
239.1.1.202 00:00:22:2e:a5:62 Static 00h00m00s ies-10-239.1.1.2 1/1/3
===============================================================================
A:ALA-A#
Label |
Description |
---|---|
IP Address |
Specifies the IP address of the ARP cache entry. |
MAC Address |
Specifies the MAC address associated with the IP address. |
Type |
Other — Learned through normal ARP queries. Static — Configured by static-arp commands. Managed — Learned from DHCP snooping or configured by host commands. |
Age |
Indicates age of the ARP entry. |
Interface |
Indicates the name of the IP interface. |
Port |
Indicates the port upon which the entry was learned. |
arp
Syntax
arp {all | ip-address}
arp interface {ip-int-name | ip-address}
Context
[Tree] (clear>router arp)
Full Context
clear router arp
Description
This command clears all or specific ARP entries.
The scope of ARP cache entries cleared depends on the command line options specified.
Parameters
- all
-
Clears all ARP cache entries.
- ip-address
-
Clears the ARP cache entry for the specified IP address.
- ip-int-name
-
Clears all ARP cache entries for the IP interface with the specified name, up to 32 characters.
- ip-address
-
Clears all ARP cache entries for the specified IP interface with the specified IP address.
Platforms
All
arp
Syntax
arp
Context
[Tree] (clear>service>id arp)
Full Context
clear service id arp
Description
This command clears all ARP entries. This command is only valid for Ipipe and VPRN services.
Platforms
All
arp
Syntax
arp [{ip-int-name | ip-address[/mask] | mac ieee-mac-address | summary}] [arp-type]
Context
[Tree] (show>router arp)
Full Context
show router arp
Description
This command displays the router ARP table sorted by IP address. If no command line options are specified, all ARP entries are displayed.
Parameters
- ip-int-name
-
Only displays ARP entries associated with the specified IP interface name.
- ip-address[/mask]
-
Only displays ARP entries associated with the specified IP address and mask.
- ieee-mac-address
-
Only displays ARP entries associated with the specified MAC address.
- summary
-
Displays an abbreviate list of ARP entries.
- arp-type
-
Only displays ARP information associated with the keyword.
Platforms
All
Output
ARP Table Output — The following output is an example of router ARP table information, and ARP Fields describes the ARP table output fields.
Output Example*B:7710-Red-RR# show router arp
===============================================================================
ARP Table (Router: Base)
===============================================================================
IP Address MAC Address Expiry Type Interface
-------------------------------------------------------------------------------
10.20.1.24 00:16:4d:23:91:b8 00h00m00s Oth system
10.10.4.11 00:03:fa:00:d0:c9 00h57m03s Dyn[I] to-core-sr1
10.10.4.24 00:03:fa:41:8d:20 00h00m00s Oth[I] to-core-sr1
-------------------------------------------------------------------------------
No. of ARP Entries: 3
===============================================================================
A:ALA-A# show router ARP 10.10.0.3
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Expiry Type Interface
-------------------------------------------------------------------------------
10.10.0.3 04:5d:ff:00:00:00 00:00:00 Oth system
===============================================================================
A:ALA-A#
A:ALA-A# show router ARP to-ser1
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Expiry Type Interface
-------------------------------------------------------------------------------
10.10.13.1 04:5b:01:01:00:02 03:53:09 Dyn to-ser1
===============================================================================
A:ALA-A#
Label |
Description |
---|---|
IP Address |
The IP address of the ARP entry |
MAC Address |
The MAC address of the ARP entry |
Expiry |
The age of the ARP entry |
Type |
Dyn — he ARP entry is a dynamic ARP entry Inv — the ARP entry is an inactive static ARP entry (invalid) Oth — the ARP entry is a local or system ARP entry Sta — the ARP entry is an active static ARP entry |
*Man |
The ARP entry is a managed ARP entry |
Int |
The ARP entry is an internal ARP entry |
[I} |
The ARP entry is in use |
Interface |
The IP interface name associated with the ARP entry |
No. of ARP Entries |
The number of ARP entries displayed in the list |
arp-host
arp-host
Syntax
arp-host [wholesaler service-id] {[sap sap-id | interface interface-name | ip-address ip-address[/mask] | mac ieee-address | {[ port port-id] [no-inter-dest-id | inter-dest-id inter-dest-id]}]} [detail]
arp-host statistics [sap sap-id | interface interface-name]
arp-host summary {[interface interface-name | saps ]
Context
[Tree] (show>service>id arp-host)
Full Context
show service id arp-host
Description
This command displays ARP host related information.
Parameters
- service-id
-
The VPRN service ID of the wholesaler. When specified in this context, SAP, SDP, interface, IP address and MAC parameters are ignored.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- interface-name
-
Displays information for the specified IP interface. 32 characters maximum.
- ip-address[/mask]
-
Displays information associated with the specified IP address.
- ieee-address
-
Specifies the MAC address.
- port-id
-
Specifies the port ID.
- no-inter-dest-id
-
Displays the information about no intermediate destination ID.
- inter-dest-id
-
Indicates the intermediate destination identifier received from either the DHCP or the RADIUS server or the local user database. 32 characters maximum
- detail
-
Displays detailed information.
- statistics
-
Displays ARP host statistics.
- summary
-
Displays summary information.
- saps
-
Displays SAP ARP host related information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example ARP host information for specified service IDs.
Output Example*A:Dut-C# show service id 2 arp-host
===============================================================================
ARP host table, service 2
===============================================================================
IP Address Mac Address Sap Id Remaining MC
Time Stdby
-------------------------------------------------------------------------------
128.128.1.2 00:80:00:00:00:01 2/1/5:2 00h04m41s
128.128.1.3 00:80:00:00:00:02 2/1/5:2 00h04m42s
128.128.1.4 00:80:00:00:00:03 2/1/5:2 00h04m43s
128.128.1.5 00:80:00:00:00:04 2/1/5:2 00h04m44s
128.128.1.6 00:80:00:00:00:05 2/1/5:2 00h04m45s
128.128.1.7 00:80:00:00:00:06 2/1/5:2 00h04m46s
128.128.1.8 00:80:00:00:00:07 2/1/5:2 00h04m47s
128.128.1.9 00:80:00:00:00:08 2/1/5:2 00h04m48s
128.128.1.10 00:80:00:00:00:09 2/1/5:2 00h04m49s
128.128.1.11 00:80:00:00:00:0a 2/1/5:2 00h04m50s
-------------------------------------------------------------------------------
Number of ARP hosts : 10
===============================================================================
*A:Dut-C#
*A:Dut-C# show service id 2 arp-host ip-address 128.128.1.2 detail
===============================================================================
ARP hosts for service 2
===============================================================================
Service ID : 2
IP Address : 128.128.1.2
MAC Address : 00:80:00:00:00:01
SAP : 2/1/5:2
Remaining Time : 00h04m58s
Sub-Ident : "alu_1_2"
Sub-Profile-String : ""
SLA-Profile-String : ""
App-Profile-String : ""
ARP host ANCP-String : ""
ARP host Int Dest Id : ""
RADIUS-User-Name : "128.128.1.2"
Session Timeout (s) : 301
Start Time : 02/09/2009 16:35:07
Last Auth : 02/09/2009 16:36:34
Last Refresh : 02/09/2009 16:36:38
Persistence Key : N/A
Subscriber Host Limit Overrides
ipv4-arp : 1
ipv4-dhcp : 1
ipv4-ppp : 1
ipv4-overall : 1
ipv6-pd-ipoe-dhcp : 1
ipv6-pd-ppp-dhcp : 1
ipv6-pd-overall : 1
ipv6-wan-ipoe-dhcp : 1
ipv6-wan-ipoe-slaac : 1
ipv6-wan-ppp-dhcp : 1
ipv6-wan-ppp-slaac : 1
ipv6-wan-overall : 1
ipv6-overall : 1
lac-overall : 1
overall : 1
SLA Profile Instance Host Limit Overrides
ipv4-arp : 1
ipv4-dhcp : 1
ipv4-ppp : 1
ipv4-overall : 1
ipv6-pd-ipoe-dhcp : 1
ipv6-pd-ppp-dhcp : 1
ipv6-pd-overall : 1
ipv6-wan-ipoe-dhcp : 1
ipv6-wan-ipoe-slaac : 1
ipv6-wan-ppp-dhcp : 1
ipv6-wan-ppp-slaac : 1
ipv6-wan-overall : 1
ipv6-overall : 1
lac-overall : 1
overall : 1
Subscriber Session Limit Overrides
ipoe : 1
pppoe-local : 1
pppoe-lac : 1
pppoe-overall : 1
l2tp-lns : 1
l2tp-lts : 1
l2tp-overall : 1
overall : 1
SLA Profile Instance Session Limit Overrides
ipoe : 1
pppoe-local : 1
pppoe-lac : 1
pppoe-overall : 1
l2tp-lns : 1
l2tp-lts : 1
l2tp-overall : 1
overall : 1
-------------------------------------------------------------------------------
Number of ARP hosts : 1
===============================================================================
*A:Dut-C#
*A:Dut-C# show service id 2 arp-host statistics
==============================================================================
ARP host statistics
==============================================================================
Num Active Hosts : 20
Received Triggers : 70
Ignored Triggers : 10
Ignored Triggers (overload) : 0
SHCV Checks Forced : 0
Hosts Created : 20
Hosts Updated : 40
Hosts Deleted : 0
Authentication Requests Sent : 40
==============================================================================
*A:Dut-C#
*A:Dut-C# show service id 2 arp-host summary
=============================================================
ARP host Summary, service 2
=============================================================
Sap Used Provided Admin State
-------------------------------------------------------------
sap:2/1/5:2 20 8000 inService
-------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------
=============================================================
*A:Dut-C#
Service ARP Host Field Descriptions describes service ARP host information.
Field |
Description |
---|---|
IP Address |
The IP address |
Mac Address |
The MAC address of the this ARP host |
Sap Id |
The service SAP ID |
Remaining Time |
The remaining time |
MC Stdby |
The MC standby |
Number of ARP hosts |
The total number of ARP hosts |
Service ID |
The service identifier |
Sub-Ident |
The name of the subscriber identification policy |
Sub-Profile-String |
The name of the subscriber profile |
SLA-Profile-String |
The name of the SLA profile |
App-Profile-String |
The application profile string |
ARP host ANCP-String |
The name of the ARP host |
ARP host Int Dest Id |
The ARP host internal destination ID |
RADIUS-User-Name |
The RADIUS user name |
Session Timeout (s) |
The session timeout value |
Start Time |
The start time |
Last Auth |
The date and time of the last authentication |
Last Refresh |
The date and time of the last refresh |
Persistence Key |
The key value that can be used to track this ARP host in the persistence file. |
Subscriber Host Limit Overrides and SLA Profile Instance Host Limit Overrides: (only shown when overrides are active) |
|
ipv4-arp |
The total number of IPv4 ARP hosts limit |
ipv4-dhcp |
The total number of IPv4 DHCP hosts limit |
ipv4-ppp |
The total number of IPv4 PPP hosts limit |
ipv4-overall |
The total number of IPv4 hosts limit |
ipv6-pd-ipoe-dhcp |
The total number of IPv6 IPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-ppp-dhcp |
The total number of IPv6 PPPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-overall |
The total number of IPv6 DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-wan-ipoe-dhcp |
The total number of IPv6 IPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ipoe-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-ppp-dhcp |
The total number of IPv6 PPPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ppp-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-overall |
The total number of IPv6 WAN hosts limit |
ipv6-overall |
The total number of IPv6 hosts limit |
lac-overall |
The total number of L2TP LAC hosts limit |
overall |
The total number of subscriber hosts limit |
Subscriber Session Limit Overrides and SLA Profile Instance Session Limit Overrides: (only shown when overrides are active) |
|
ipoe |
The total number of IPoE sessions limit |
ppoe-local |
The total number of PPPoE local terminated sessions (PTA) limit |
ppoe-lac |
The total number of PPPoE L2TP LAC sessions limit |
ppoe-overall |
The total number of PPPoE sessions limit |
l2tp-lns |
The total number of L2TP LNS sessions limit |
l2tp-lts |
The total number of L2TP LTS sessions limit |
l2tp-overall |
The total number of L2TP sessions limit |
overall |
The total number of subscriber sessions limit |
Number of hosts |
The total number of hosts matching the search criteria |
MC-Stdby |
The number of SAPs defined on this service on a port which is in multi-chassis standby mode |
arp-host
Syntax
arp-host {all | mac ieee-address | sap sap-id | ip-address ip-address[/mask]}
arp-host {port port-id | {inter-dest-id intermediate-destination-id | no-inter-dest-id} [port port-id]}
arp-host statistics [sap sap-id | interface interface-name]
Context
[Tree] (clear>service>id arp-host)
Full Context
clear service id arp-host
Description
This command clears ARP host data.
Parameters
- all
-
Clears all ARP host statistics.
- ieee-address
-
Clears the ARP host MAC address information. The 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.
- sap-id
-
Clears the specified SAP information.
- ip-address[/mask]
-
Clears the specified IP address and mask.
- port-id
-
Clear the specified port ID information.
- intermediate-destination-id
-
Displays information about the specified intermediate destination ID. 32 characters maximum.
- no-inter-dest-id
-
Displays the information about no intermediate destination ID.
- interface-name
-
Clears the interface name. 32 characters maximum.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
arp-table
arp-table
Syntax
arp-table [ip ipv4-address] [class class] [next-index index]
Context
[Tree] (tools>dump>wlan-gw>lanext>bd arp-table)
Full Context
tools dump wlan-gw lanext bd arp-table
Description
This command dumps the specified ARP table entries for the specified HLE BD.
Parameters
- ipv4-address
-
Specifies the IP address of the ARP entry to be displayed.
- class
-
Specifies the source on which to filter the ARP table entries.
- index
-
Specifies the next set of results if there are more results than the current output. The additional results are shown at the bottom of the current output.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of ARP table information.
Output Exampletools>dump>wlan-gw>lanext>bd# arp-table
===============================================================================
MATCHED 1 ARP ENTRY ON SLOT #2 MDA #1
===============================================================================
IP ADDRESS MAC ADDRESS CLASS TIMESTAMP
-------------------------------------------------------------------------------
192.168.0.1 AA:BB:CC:00:00:01 ACCESS 05/30/2017 23:49:11
===============================================================================
aspath-regex
aspath-regex
Syntax
aspath-regex reg-exp {detail | longer}
aspath-regex reg-exp
aspath-regex reg-exp hunt
Context
[Tree] (show>router>bgp>routes aspath-regex)
Full Context
show router bgp routes aspath-regex
Description
This command displays BGP routes with an AS path matching the specified regular expression.
aspath-regex is a parameter of the show router bgp routes command. Depending on the parameters that are used to issue the command, the output can display a narrower or wider set of routes, including routes belonging to other address families. See the show router bgp routes command description for syntax variants, parameter descriptions and values, and output examples.
Platforms
All
association
association
Syntax
association [ma-index | ma-admin-name] [ detail]
Context
[Tree] (show>eth-cfm association)
Full Context
show eth-cfm association
Description
This command displays ETH-CFM association information.
Parameters
- ma-index
-
Specifies the maintenance association (MA) index.
- ma-admin-name
-
Specifies the administrative name for the association, up to 64 characters.
- detail
-
Keyword to display detailed information for the ETH-CFM association.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of ETH-CFM association information, and the following table describes the output fields.
Output ExampleA:node-2# show eth-cfm association
===============================================================================
CFM Association Table
===============================================================================
Md-index Ma-index Name Int Hold Bridge-id MEPS TxSid
md-admin-name
ma-admin-name
bridge-name
-------------------------------------------------------------------------------
10 100 vpls-100-0 1 n/a 1 no
10
100
vpls-100
12 1000 vpls-100-1 1 n/a 4 yes
12
vpls-100-1
vpls-100
===============================================================================
*A:node-2# show eth-cfm association 1 detail
-------------------------------------------------------------------------------
Domain 1 Associations:
-------------------------------------------------------------------------------
Md-index : 1 Ma-index : 1
Name Format : charString CCM-interval : 10
Name : test-ma-1
Bridge-id : 2 MHF Creation : defMHFnone
PrimaryVlan : 0 Num Vids : 0
Remote Mep Id : 1
Remote Mep Id : 4
Remote Mep Id : 5
-------------------------------------------------------------------------------
Label |
Description |
---|---|
Md-index |
Displays the maintenance domain (MD) index |
Ma-index |
Displays the maintenance association (MA) index |
Name |
Displays the part of the maintenance association identifier which is unique within the maintenance domain name |
Int |
Displays the CCM transmission interval for all MEPs in the association |
Hold |
Displays the CCM hold time, in milliseconds, that is added before the defect condition is raised. A value of "n/a" indicates that the MEP is not subsecond and does not support the CCM hold time. |
Bridge-id |
Displays the bridge-identifier value for the domain association |
MEPS |
Displays the total local and remote maintenance association end point (MEP) |
TxSid |
Yes — the Sender ID TLV is included in the supported ETH-CFM PDUs No — the Sender ID TLV is not included in the supported ETH-CFM PDUs |
md-admin-name |
Displays the administrative MD name |
ma-admin-name |
Displays the administrative MA name |
bridge-name |
Displays the administrative bridge-identifier name |
association
Syntax
association
association name [statistics]
Context
[Tree] (show>subscr-mgmt>pfcp association)
Full Context
show subscriber-mgmt pfcp association
Description
This command displays PFCP association information. If no parameters are entered, it displays an overview of all PFCP associations present on the system.
Parameters
- name
-
Specifies the name of the configured PFCP association, up to 32 characters, for which detailed overview information is displayed.
- statistics
-
Specifies that the packet counters for each PFCP message and upstream IBCP message for the specified PFCP association name are displayed.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following outputs are examples of PFCP association output information and the corresponding table describes the output fields:
-
Output Example: show subscriber-mgmt pfcp association; PFCP Association Field Descriptions
-
Output Example: show subscriber-mgmt pfcp association name; PFCP Association Name Field Descriptions
-
Output Example: show subscriber-mgmt pfcp association name statistics
#BNG-UPF# show subscriber-mgmt pfcp association
===============================================================================
PFCP Associations
===============================================================================
Name Description
-------------------------------------------------------------------------------
bng-cpf (Not Specified)
-------------------------------------------------------------------------------
No. of configured PFCP Associations: 1
===============================================================================
PFCP Association Field Descriptions describes the output fields for the show subscriber-mgmt pfcp association command.
Label |
Description |
---|---|
Name |
Displays the name of each PFCP association configured in the system |
Description |
Displays the description of each PFCP association, if configured |
===============================================================================
A:BNG-UPF# show subscriber-mgmt pfcp association "bng-cpf"
===============================================================================
PFCP Association bng-cpf
===============================================================================
Admin Status : up
Oper Status : up
Router : to_cpf
Interface : endpoint
Peer Node Id : 17.17.17.10
Peer Address : 17.17.17.10
Local Node Id : 192.0.2.11
Local Address : 192.0.2.11
UP Features : FTUP TREU PDIU FRRT ADPDP MNOP IP6PL
UP BBF Features : PPPOE IPOE LCPKO
UP NOKIA Features : BULKAUDIT
CP Features :
Setup Retry : 1 second
Release Timeout : 1 hour
Path Restoration Time : (Not Specified)
Heartbeat Interval : 1 minute
Heartbeat Timeout : 5 seconds
Heartbeat Retries : 4
Tx Timeout : 5 seconds
Tx Retries : 3
Tx TTL : 255
NAT group : (Not Specified)
Created : 01/08/2021 16:26:07
Last Updated : 01/08/2021 16:26:07
===============================================================================
PFCP Association Name Field Descriptions describes the output fields for the show subscriber-mgmt pfcp association name command.
Label |
Description |
---|---|
Admin Status |
Administrative status of this PFCP association down — association is administratively disabledup — association is administratively enabled |
Oper Status |
Operational status of this PFCP association down — association is operationally disabledup — association is operationally enabled |
Router |
Router name for this association |
Interface |
Interface for this association |
Peer Node Id |
CPF peer node ID |
Peer address |
CPF peer node IP address |
Local Node Id |
Local UPF node ID |
Local address |
Local UPF node IP address |
UP Features |
UPF features |
UP BBF Features |
UPF BBF features |
UP NOKIA Features |
UPF Nokia features |
CP Features |
CPF features |
Setup Retry |
Configured time to wait before an association setup retry attempt after failure |
Release Timeout |
Configured time to wait for a response to a release request |
Path Restoration Time |
Configured time to wait before the path is declared down |
Heartbeat Interval |
Configured interval time between two heartbeat request messages |
Heartbeat Timeout |
Configured time the system waits for a heartbeat response message |
Heartbeat Retries |
Configured number of retries after the heartbeat timeout expires |
Tx Timeout |
Configured transmit timeout |
Tx Retries |
Configured transmit retries |
Tx TTL |
Configured transmit TTL |
NAT group |
Configured NAT group |
Created |
PFCP association create time |
Last Updated |
PFCP association update time |
===============================================================================
A:BNG-UPF# show subscriber-mgmt pfcp association "bng-cpf" statistics
===============================================================================
PFCP Statistics for Association 'bng-cpf'
===============================================================================
PFCP Session Related Messages
Session Establish Req : 1 Session Establish Resp : 1
Session Establish Resp fail: 0
Session Modify Req : 0 Session Modify Resp : 0
Session Modify Resp fail : 0
Session Deletion Req : 1 Session Deletion Resp : 0
Session Deletion Resp fail : 1
Session Report Req : 0 Session Report Resp : 0
Session Report Resp fail : 0
Session Report DDR Req : 0 Session Report DDR Rsp : 0
Session Report DDR Rsp fail: 0
Session Report UR Req : 0 Session Report UR Rsp : 0
Session Report UR Rsp fail : 0
Session Report EIR Req : 0 Session Report EIR Rsp : 0
Session Report EIR Rsp fail: 0
Session Report UPIR Req : 0 Session Report UPIR Rsp : 0
Session Report UPIR Rs fail: 0
PFCP Session Audit Related Messages
Session Modify Req : 0 Session Modify Resp : 0
Session Modify Resp fail : 0
Session Report Req : 0 Session Report Rsp : 0
Session Report Rsp fail : 0
PFCP Node Related Messages
Node Report Req : 0 Node Report Resp : 0
Node Report Resp fail : 0
Assoc Setup Req Rx : 0 Assoc Setup Resp Rx : 1
Assoc Setup Resp fail Rx : 0
Assoc Setup Req Tx : 1 Assoc Setup Resp Tx : 0
Assoc Setup Resp fail Tx : 0
Assoc Upd Req Rx : 0 Assoc Upd Resp Rx : 0
Assoc Upd Resp fail Rx : 0
Assoc Upd Req Tx : 0 Assoc Upd Resp Tx : 0
Assoc Upd Resp fail Tx : 0
Assoc Upd Req with ARR : 0 Assoc Upd Req with GRP : 0
Assoc Upd Req ARR & GRP : 0
Assoc Release Req : 0 Assoc Release Resp : 0
Assoc Release Resp fail : 0
Heartbeat Req Rx : 2 Heartbeat Resp Rx : 0
Heartbeat Req Tx : 0 Heartbeat Resp Tx : 2
Heartbeat Aud Trig Req Tx : 0 Heartbeat Aud Trig Rsp Rx : 0
Heartbeat Aud Start Req Rx : 0 Heartbeat Aud Start Rsp Tx : 0
Heartbeat Aud End Req Rx : 0 Heartbeat Aud End Rsp Tx : 0
IBCP upstream packet statistics
Ipoe Rx Pkts : 0
Pppoe Ctrl Rx Pkts : 0
Pppoe Data Rx Pkts : 0
Tx Pkts to Smf : 0
IBCP upstream packet discard statistics
Missing pkt detection rule : 0
Default tnl trigger missing: 0
Default tunnel missing : 0
Parsing error : 0
Tx error : 0
IBCP default tunnel
overwrite : 0
Last cleared time : 01/08/2021 16:26:07
==============================================================================
associations
associations
Syntax
associations
Context
[Tree] (show>router>dhcp6>local-dhcp-server associations)
[Tree] (show>router>dhcp>local-dhcp-server associations)
Full Context
show router dhcp6 local-dhcp-server associations
show router dhcp local-dhcp-server associations
Description
This command displays the interfaces associated with this DHCP or DHCP6 server.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of information associated with this DHCP or DHCP6 server.
Output Example*A:SUB-Dut-A# show router dhcp local-dhcp-server dhcpS1 associations
===============================================================================
DHCP server s1 router 3
===============================================================================
Associations Admin
-------------------------------------------------------------------------------
tosim5 Up
===============================================================================
*A:SUB-Dut-A#
*A:SUB-Dut-A# show router dhcp6 local-dhcp-server abc associations
===============================================================================
DHCP server abc router 3
===============================================================================
Associations Admin
-------------------------------------------------------------------------------
tosimxyz Up
===============================================================================
*A:SUB-Dut-A#
DHCP6 Summary Field Descriptions describes DHCP associations fields.
Label |
Description |
---|---|
Associations |
The entity associated with the local DHCP server |
Admin |
The administrative state |
associations
Syntax
associations
associations per-link-hash interface
associations per-link-hash class {1 | 2 | 3} interface
associations link-map-profile [link-map-profile] interface
associations per-link-hash [class {1 | 2| 3}] sap
associations link-map-profile [link-map-profile] sap
Context
[Tree] (show>lag associations)
Full Context
show lag associations
Description
This command displays LAG association information.
Parameters
- link-map-profile
-
Displays information about a specified LAG link map profile.
Platforms
All
auth-keychain
auth-keychain
Syntax
auth-keychain [keychain]
Context
[Tree] (show>router>bgp auth-keychain)
Full Context
show router bgp auth-keychain
Description
This command displays BGP sessions using a particular authentication keychain.
Parameters
- keychain
-
Specifies an existing keychain name.
Platforms
All
Output
The following output is an example of authentication keychain information.
Output Example*A:ALA-48# show router 2 bgp auth-keychain
===============================================================================
Sessions using key chains
===============================================================================
Peer address Group Keychain name
-------------------------------------------------------------------------------
10.20.1.3 1 eta_keychain1
30.1.0.2 1 eta_keychain1
===============================================================================
*A:ALA-48#
*A:ALA-48>config>router>bgp# show router bgp group "To_AS_10000"
===============================================================================
BGP Group : To_AS_10000
-------------------------------------------------------------------------------
Group : To_AS_10000
-------------------------------------------------------------------------------
Group Type : No Type State : Up
Peer AS : 10000 Local AS : 200
Local Address : n/a Loop Detect : Ignore
Import Policy : None Specified - Default Accept
Export Policy : ospf3
Hold Time : 90 Keep Alive : 30
Cluster Id : 0.0.0.100 Client Reflect : Enabled
NLRI : Unicast Preference : 170
TTL Security : Disabled Min TTL Value : n/a
Graceful Restart : Enabled Stale Routes Time: 360
Auth key chain : testname
List of Peers
- 10.0.0.8 :
To_Router B - EBGP Peer
Total Peers : 1 Established : 0
-------------------------------------------------------------------------------
Peer Groups : 1
===============================================================================
*A:ALA-48>config>router>bgp#
*A:ALA-48>config>router>bgp# show router bgp neighbor 10.0.0.8
===============================================================================
BGP Neighbor
-------------------------------------------------------------------------------
Peer : 10.0.0.8
Group : To_AS_10000
-------------------------------------------------------------------------------
Peer AS : 10000 Peer Port : 0
Peer Address : 10.0.0.8
Local AS : 200 Local Port : 0
Local Address : 0.0.0.0
Peer Type : External
State : Active Last State : Idle
Last Event : stop
Last Error : Cease
Local Family : IPv4
Remote Family : Unused
Hold Time : 90 Keep Alive : 30
Active Hold Time : 0 Active Keep Alive : 0
Cluster Id : 0.0.0.100
Preference : 99 Num of Flaps : 0
Recd. Paths : 0
IPv4 Recd. Prefixes : 0 IPv4 Active Prefixes : 0
IPv4 Suppressed Pfxs : 0 VPN-IPv4 Suppr. Pfxs : 0
VPN-IPv4 Recd. Pfxs : 0 VPN-IPv4 Active Pfxs : 0
Mc IPv4 Recd. Pfxs. : 0 Mc IPv4 Active Pfxs. : 0
Mc IPv4 Suppr. Pfxs : 0 IPv6 Suppressed Pfxs : 0
IPv6 Recd. Prefixes : 0 IPv6 Active Prefixes : 0
Input Queue : 0 Output Queue : 0
i/p Messages : 0 o/p Messages : 0
i/p Octets : 0 o/p Octets : 0
i/p Updates : 0 o/p Updates : 0
TTL Security : Disabled Min TTL Value : n/a
Graceful Restart : Enabled Stale Routes Time : 360
Advertise Inactive : Disabled Peer Tracking : Disabled
Advertise Label : None
Auth key chain : testname
Local Capability : RouteRefresh MP-BGP
Remote Capability :
Import Policy : None Specified - Default Accept
Export Policy : ospf3
-------------------------------------------------------------------------------
Neighbors : 1
===============================================================================
*A:ALA-48>config>router>bgp#
*A:ALA-48>config>router>bgp# show router bgp auth-keychain testname
=========================================================================
Sessions using key chain: keychain
=========================================================================
Peer address Group Keychain name
-------------------------------------------------------------------------
10.0.0.8 To_AS_10000 testname
=========================================================================
*A:ALA-48>config>router>bgp#
authentication
authentication
Syntax
authentication user-name user-name password password [circuit-id circuit-id] [ circuit-id-hex circuit-id-hex] [derived-id derived-id] [ mac ieee-address] [remote-id remote-id] [ remote-id-hex remote-id-hex] [sap-id sap-id] [ service-name service-name]
Context
[Tree] (tools>perform>subscr-mgmt>loc-user-db>ppp authentication)
Full Context
tools perform subscriber-mgmt local-user-db ppp authentication
Description
This command authenticates the PPPoE user name.
Parameters
- user-name
-
Specifies the PPP user name up to 253 characters.
- password
-
Specifies the password of this host up to 64 characters.
- circuit-id
-
Specifies the circuit ID up to 127 characters.
- circuit-id-hex
-
Specifies the circuit ID in hexadecimal format.
- derived-id
-
Specifies an ASCII string that uniquely identifies a host, and is derived by a Python script from packet content available during a DHCP transaction up to 255 characters.
- ieee-address
-
Specifies information about the MAC address of the PPP session.
- remote-id
-
Specifies that information that goes into the remote-id sub-option in the DHCP relay packet, up to 255 characters.
- remote-id-hex
-
Specifies the remote ID in hexadecimal format.
- sap-id
-
Specifies a SAP ID, up to 255 characters.
- service-name
-
Specifies the service name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
authentication
Syntax
authentication policy-name association
authentication [policy-name]
authentication [policy-name] statistics
authentication coa-statistics
Context
[Tree] (show>subscr-mgmt authentication)
Full Context
show subscriber-mgmt authentication
Description
This command displays subscriber management RADIUS authentication policy information and statistics.
Parameters
- policy-name
-
Specifies the subscriber management RADIUS authentication policy name, up to 32 characters, for which information is requested.
- association
-
Displays SAP, interface, local user database host, AA and L2TP associations of this policy.
- coa-statistics
-
Displays the overall statistics for incoming RADIUS Change of Authorization (CoA) messages and Disconnect Messages. For dropped requests, a counter for different drop reasons is available.
- statistics
-
Displays a list of policies with basic statistics (without specifying a policy name) or detailed statistics, including per-server statistics for the specified policy-name. These statistics apply only to the legacy RADIUS server configuration method where the servers are directly configured in the authentication policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management authentication information.
Output Example# show subscriber-mgmt authentication
===============================================================================
Authentication Policies
===============================================================================
Name Description
-------------------------------------------------------------------------------
auth-policy-1 Radius auth policy - servers
auth-policy-2 Radius auth policy - radius-server-policy
-------------------------------------------------------------------------------
Number of Authentication Policies : 2
===============================================================================
# show subscriber-mgmt authentication "auth-policy-2"
===============================================================================
Authentication Policy auth-policy-2
===============================================================================
Description : Radius auth policy - radius-server-policy
Re-authentication : Yes Username Format : MAC Address
PPPoE Access Method : PAP/CHAP Username Mac-Format : "aa:"
PPP-Username Oper : None
PPP-Domain-Name : N/A
Username Oper : None
Domain-Name : N/A
Acct-Stop-On-Fail :
RADIUS Server Policy : "aaa-server-policy-1"
Fallback Action : deny
Last Mgmt Change : 06/24/2013 21:16:50
-------------------------------------------------------------------------------
Include Radius Attributes
-------------------------------------------------------------------------------
Remote Id : Yes Circuit Id : Yes
NAS Port Id : Yes NAS Identifier : Yes
PPPoE Service Name : Yes DHCP Vendor Class Id : Yes
Access Loop Options : Yes MAC Address : Yes
NAS Port Prefix : None NAS Port Suffix : None
NAS-Port-Type : Yes (standard) Acct Session Id : Host
Calling Station Id : Yes (sap-string) Called Station Id : Yes
Tunnel Server Attr : Yes DHCP Options : Yes
NAS Port : Yes
NAS Port Bits Spec : *3s*1m*4p*12o*12i
-------------------------------------------------------------------------------
Radius Servers
-------------------------------------------------------------------------------
Router : management + Base Source Address : N/A
Access Algorithm : Direct Retry : 3
Timeout (s) : 5 Hold down time (s) : 30
-------------------------------------------------------------------------------
Index IP Address Port Pend-Req-Limit Out/Overload time (s) Oper State
-------------------------------------------------------------------------------
No Radius Servers configured.
-------------------------------------------------------------------------------
Accept Radius Attributes
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Radius Script Policies
-------------------------------------------------------------------------------
Access-Request : "N/A"
Access-Accept : "N/A"
Change-of-Authorization : "N/A"
===============================================================================
# show subscriber-mgmt authentication "auth-policy-2" association
===============================================================================
Authentication Policy auth-policy-2
===============================================================================
-------------------------------------------------------------------------------
SAP Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
Interface Associations
-------------------------------------------------------------------------------
Service-Id : 3000 (VPRN)
- If Name : group-int-ws-1-1
-------------------------------------------------------------------------------
Local-User-Db PPPoE Host Associations
-------------------------------------------------------------------------------
Local-User-Db : ludb-1
- Host : host-1
-------------------------------------------------------------------------------
Local-User-Db DHCP Host Associations
-------------------------------------------------------------------------------
Local-User-Db : ludb-1
- Host : default
-------------------------------------------------------------------------------
Application Assurance Associations
-------------------------------------------------------------------------------
No associations found.
===============================================================================
No associated L2TP groups found.
No associated L2TP tunnels found.
# show subscriber-mgmt authentication statistics
===============================================================================
Authentication Policy Statistics
===============================================================================
Policy Name Subscr. Pkts Subscr. Pkts Subscr. Pkts
Authenticated Rejected Rejected
Send Failed
-------------------------------------------------------------------------------
auth-policy-1 0 0 0
auth-policy-2 0 0 0
-------------------------------------------------------------------------------
Number of Authentication Policies : 2
===============================================================================
# show subscriber-mgmt authentication "auth-policy-1" statistics
===============================================================================
Authentication Policy Statistics
===============================================================================
-------------------------------------------------------------------------------
Policy name : auth-policy-1
subscriber packets authenticated : 0
subscriber packets rejected : 0
subscriber packets rejected send failed : 0
-------------------------------------------------------------------------------
radius server requests requests requests requests requests requests
idx IP-address accepted rejected no reply md5 failed pending send failed
-------------------------------------------------------------------------------
1 172.16.1.1 0 0 0 0 0 0
-------------------------------------------------------------------------------
===============================================================================
# show subscriber-mgmt authentication coa-statistics
===============================================================================
Radius Notify Statistics Change-Of-Authorization Disconnect-Messages
===============================================================================
Requests Received 7 10
Requests Accepted 5 6
Requests Rejected 2 4
Requests Dropped 0 0
No Auth Policy found 0 0
Invalid message 0 0
Out of resources 0 0
Authentication failure 0 0
===============================================================================
Label |
Description |
---|---|
Re-authentication |
Whether re-authentication on IPOE renewal is enabled |
Username Format |
The user name format in RADIUS message |
PPPoE Access Method |
The PPPoE access method, none, padi, pap-chap |
Username Mac-Format |
The username is represented when contacting a RADIUS server. |
PPP-Username Oper |
The PPP user name operation |
PPP-Domain-Name |
The PPP domain name |
Username Oper |
The username |
Acct-Stop-On-Fail |
The failure condition a RADIUS accounting-stop message indicating the failure has to be sent |
RADIUS Server Policy |
The RADIUS server policy name |
Fallback Action |
The authentication action in case no RADIUS server is available |
Lack Mgmt Change |
The time of the most recent management-initiated change to this policy server |
Remote Id |
The value of the remote ID sub-option |
NAS Port Id |
NAS port ID generation enabled or disabled |
PPPoE Service Name |
The PPPoE service name |
Access Loop Options |
The generation of the DSL forum access loop characteristics RADIUS attributes enabled or disabled |
NAS Port Prefix |
The type of prefix added to the NAS-Port attribute if included in RADIUS authentication request messages |
NAS-Port-Type |
The kind of value to be put in the RADIUS NAS-Port-Type attribute if included in RADIUS authentication request messages |
Calling Station Id |
The string will be put in the RADIUS Calling-Station-Id attribute if included in RADIUS authentication request messages |
Tunnel Server Attr |
The tunnel-server-attrs RADIUS attribute enabled or disabled |
NAS Port |
The NAS-Port attribute included or excluded |
NAS Port Bits Spec |
The number that will be put in the RADIUS NAS-Port attribute if included in RADIUS authentication request messages |
Circuit Id |
Circuit ID generation enabled or disabled |
NAS Identifier |
NAS-Identifier RADIUS attribute enabled or disabled |
DHCP Vendor Class Id |
dhcp-vendor-class-id RADIUS attribute enabled or disabled |
MAC Address |
The generation of the client MAC address RADIUS attribute enabled or disabled |
NAS Port Suffix |
The type of suffix is added to the NAS-Port-Id attribute if included in RADIUS accounting-request messages |
Acct Session Id |
The RADIUS accounting session id for this subscriber host |
DHCP Options |
DHCP options enabled or disabled |
Router |
The RADIUS router name |
Access Algorithm |
The algorithm used to access the set of RADIUS servers |
Timeout (s) |
The timeout for a response from the RADIUS server |
Source Address |
The source address of the RADIUS message |
Retry |
The number of retries for contacting the RADIUS server |
Hold down time (s) |
The hold down time |
Index IP Address |
The IP address of the index |
Port |
The port ID |
Pend-Req-Limit |
The limit of the number of pending RADIUS authentication requests for this RADIUS server |
Out/Overload time (s) |
The accumulated time that the value of the object RADIUS server has been equal to 'overloaded' since created |
Oper State |
The operational state |
Access-Request |
The number of Access-Request packets received by this RADIUS proxy server |
Access-Accept |
The number of Access-Accept packets received by this RADIUS proxy server |
Change-of-Authorization |
Change of authorization enabled or disabled |
Policy Name |
The authentication policy name |
Subscr. Pkts Authenticated |
The number of subscriber packets authenticated |
Subscr. Pkts Rejected |
The number of subscriber packets rejected |
Subscr. Pkts Rejected Send Failed |
The number of subscriber messages (such as DHCP and PPPoE) failed to be sent |
subscriber packets authenticated |
The number of subscriber packets authenticated |
subscriber packets rejected |
The number of subscriber packets rejected |
subscriber packets send failed |
The number of subscriber packets failed to be sent |
Requests Received |
The number of notify Change-of-Authorization requests received |
Requests Accepted |
The number of notify Change-of-Authorization requests accepted |
Requests Rejected |
The number of notify Change-of-Authorization requests rejected |
Requests Dropped |
The number of notify Change-of-Authorization requests dropped |
No Auth Policy found |
The number of notify Change-of-Authorization requests found |
Invalid message |
The number of notify Change-of-Authorization requests rejected because of decode errors |
Out of resources |
The number of notify Change-of-Authorization requests rejected due to lack of resources |
Authentication Failure |
The number of notify Change-of-Authorization requests which do not have NAS-Port-ID or Framed-IP-Address set or have mismatched subscriber-id |
authentication
Syntax
authentication [policy-name]
authentication coa-statistics
Context
[Tree] (clear>subscr-mgmt authentication)
Full Context
clear subscriber-mgmt authentication
Description
This command clears subscriber authentication data.
Parameters
- policy-name
-
Clears the specifies existing authentication policy name.
- coa-statistics
-
Clears statistics for incoming RADIUS Change of Authorization requests.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
authentication
Syntax
authentication
Context
[Tree] (show>service>id authentication)
Full Context
show service id authentication
Description
Commands in this context show session authentication information.
Platforms
All
authentication
Syntax
authentication
Context
[Tree] (clear>service>id authentication)
Full Context
clear service id authentication
Description
Commands in this context clear session authentication information.
Platforms
All
authentication
Syntax
authentication
Context
[Tree] (show>router authentication)
Full Context
show router authentication
Description
This command enables the command to display authentication statistics.
Platforms
All
authentication
Syntax
authentication
Context
[Tree] (clear>router authentication)
Full Context
clear router authentication
Description
This command clears authentication related data.
Platforms
All
authentication
Syntax
authentication [statistics]
Context
[Tree] (show>system>security authentication)
Full Context
show system security authentication
Description
This command displays system login authentication configuration and statistics.
Parameters
- statistics
-
Appends login and accounting statistics to the display.
Platforms
All
Output
The following output is an example of authentication information.
Show System Security Authentication Output Fields describes system security authentication output fields.
Output ExampleA:ALA-4# show system security authentication statistics
============================================================================
Authentication sequence : radius tacplus ldap local
============================================================================
type status timeout (secs) retry count
server address
server name
----------------------------------------------------------------------------
radius up 3 3
192.168.0.10:1812
tacplus up 3 n/a
192.168.1.10:49
ldap up 3 3
10.1.1.1:389
----------------------------------------------------------------------------
radius admin/oper status : up/up
UDP port : 1812
tacplus admin/oper status : up/up
ldap admin/oper status : up/up
health check : enabled (interval 30 secs)
----------------------------------------------------------------------------
No. of Servers: 3
===============================================================================
Login Statistics
===============================================================================
server address conn accepted rejected
errors logins logins
-------------------------------------------------------------------------------
192.168.0.10 0 0 0
192.168.1.10 0 0 0
10.1.1.1 0 0 0
local n/a 0 0
===============================================================================
Authorization Statistics (TACACS+)
===============================================================================
server address conn sent rejected
errors pkts pkts
-------------------------------------------------------------------------------
192.168.1.10 0 0 0
===============================================================================
Accounting Statistics
===============================================================================
server address conn sent rejected
errors pkts pkts
-------------------------------------------------------------------------------
192.168.0.10 0 0 0
192.168.1.10 0 0 0
============================================================================
Label |
Description |
---|---|
sequence |
The sequence in which authentication is attempted |
type |
The type of server |
status |
The status of the server |
timeout (secs) |
The number of seconds the system waits for a response from a server |
retry count |
The number of retry attempts to contact the server |
server address |
The IP address of the server |
server name |
The optional description of the server |
admin/oper status |
The administrative and operational status for each type, and RADIUS server ports in use |
health check |
Whether the servers are periodically monitored |
No. of Servers |
The total number of configured servers |
conn errors |
The number of connection errors |
accepted logins |
The number of logins accepted by the server |
rejected logins |
The number of logins rejected by the server |
sent pkts |
The number of packets sent |
rejected pkts |
The number of packets rejected |
authentication-origin
authentication-origin
Syntax
authentication-origin [priority [priority]]
Context
[Tree] (show>subscr-mgmt authentication-origin)
Full Context
show subscriber-mgmt authentication-origin
Description
This command displays subscriber authentication origin information.
Parameters
- priority
-
Displays information about the specified authentication origin priority override.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of authentication origin information. Show Authentication Origin Output Fields describes authentication origin output fields.
Output Example*A:cses-V26>config>subscr-mgmt>auth-orig# show subscriber-mgmt authentication-origin
===============================================================================
Authentication Origins
===============================================================================
Priority Source
-------------------------------------------------------------------------------
1 python
2 diameterGx
3 ludb
4 radius
5 diameterNasreq
6 localAddressAssignment
7 gtp
8 dhcp
-------------------------------------------------------------------------------
Number of Authentication Origins : 8
===============================================================================
*A:cses-V26>config>subscr-mgmt>auth-orig#
Field |
Description |
---|---|
Priority |
The relative order of authentication priorities |
Source |
The source of authentication priority |
Number of Authentication Origins |
The number of authentication origins |
authentication-server-check
authentication-server-check
Syntax
authentication-server-check server-address ip-address [port port] {{user-name user-name password password} | attr-from-file file-url} secret key [source-address ip-address] [timeout seconds] [ router router-instance | service-name service-name] nas-identifier nas-id [ debug]
Context
[Tree] (tools>perform>security authentication-server-check)
Full Context
tools perform security authentication-server-check
Description
This command is used to perform an authentication check on the RADIUS server.
Parameters
- server-address ip-address
-
Specifies the IP address of the RADIUS server.
- port
-
Specifies the port of the RADIUS server.
- user-name
-
Specifies the user name, up to 253 characters.
- password
-
Specifies the user password, up to 64 characters.
- file-url
-
Specifies to attach additional VSAs from a file.
- key
-
Specifies the secret key shared between the RADIUS client and server, up to 64characters.
- source address ip-address
-
Specifies the source address used for the access-request message.
- seconds
-
Specifies the time to wait for the RADIUS server response.
- router-instance
-
Specifies the router instance that should be used by the access request message.
- service-name
-
Specifies the service name that should be used by the access request message, up to 64 characters.
- nas-id
-
Specifies the NAS identifier, up to 64 characters.
- debug
-
Specifies to display the full debug message, including all VSAs and full hex sting, of the RADIUS reply message.
Platforms
All
auto-boot
auto-boot
Syntax
auto-boot {retry | terminate}
auto-boot echo [debugger]
no auto-boot echo [debugger]
Context
[Tree] (tools>perform auto-boot)
Full Context
tools perform auto-boot
Description
This command starts and stops the auto-boot process. It is also used to enable the display of auto-discovery information in the CLI.
This command can be used only if the auto-boot flag is enabled in the BOF.
The no form of this command disables the display of auto-discovery information.
Parameters
- retry
-
Executes the auto-boot process.
- terminate
-
Stops an ongoing auto-boot process.
- echo
-
Enables the display of auto-discovery information in the CLI.
- debugger
-
Includes debugging information in the displayed auto-discovery information.
Platforms
7450 ESS-7, 7750 SR-1, 7750 SR-7, 7750 SR-1e, 7750 SR-2e, 7750 SR-s
auto-boot
Syntax
auto-boot [detail]
auto-boot log
Context
[Tree] (tools>dump auto-boot)
Full Context
tools dump auto-boot
Description
This command displays auto-boot process information.
Parameters
- detail
-
Displays detailed information.
- log
-
Saves auto-boot process information to a log file.
Platforms
7450 ESS-7, 7750 SR-1, 7750 SR-7, 7750 SR-1e, 7750 SR-2e, 7750 SR-s
auto-disc
auto-disc
Syntax
auto-disc [hunt | detail] [rd rd] [community comm-id] [tag tag] [next-hop next-hop] [esi esi] [aspath-regex reg-exp]
Context
[Tree] (show>router>bgp>routes>evpn auto-disc)
Full Context
show router bgp routes evpn auto-disc
Description
This command displays BGP-EVPN auto discovery routes.
Parameters
- hunt
-
Displays entries for the specified route.
- detail
-
Displays detailed information.
- rd
-
Displays information for the route distinguisher.
- comm-id
-
Specifies the community ID, up to 72 characters.
- tag
-
Specifies the auto discovery route tag.
- next-hop
-
Specifies the IPv4 or IPv6 BGP next-hop address.
- esi
-
Specifies a 10-byte ESI by which to filter the displayed information. For example,ESI-0 | ESI-MAX or 00-11-22-33-44-55-66-77-88-99 with any of these separators('-',':',' ')
- reg-exp
-
Displays routes matching the specified regular expression, up to 80 characters.
Platforms
All
auto-discovered-meps
auto-discovered-meps
Syntax
auto-discovered-meps [mep-id] domain md-index association ma-index
Context
[Tree] (clear>eth-cfm auto-discovered-meps)
Full Context
clear eth-cfm auto-discovered-meps
Description
This command clears remote MEPs that were auto discovered. The function clears a specific auto-discovered MEP learned within an association or all auto-discovered MEPs in the association. When the mep-id representing the auto-discovered MEP is omitted and only the domain md-index and association ma-index are provided, all auto-discovered MEPs in the association are cleared. At a minimum the domain md-index and the association ma-index must be provided.
Only auto-discovered MEPs may be cleared. This command has no effect on manually configured MEPs.
Parameters
- mep-id
-
Specifies the MEP ID of the remote MEP that was auto-discovered.
- md-index
-
Specifies the domain context in which the remote MEP was auto-discovered.
- ma-index
-
Specifies the association context in which the remote MEP was auto-discovered.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
auto-lsp
auto-lsp
Syntax
auto-lsp
Context
[Tree] (clear>router>mpls>lsp auto-lsp)
Full Context
clear router mpls lsp auto-lsp
Description
Commands in this context reset and restart all auto LSPs.
Platforms
All
auto-node-provisioning
auto-node-provisioning
Syntax
auto-node-provisioning
Context
[Tree] (tools>perform>system auto-node-provisioning)
Full Context
tools perform system auto-node-provisioning
Description
This command initiates auto-provisioning of the node on all ports that are operationally up but do not have an IP address.
Platforms
All
autoconfigure
autoconfigure
Syntax
autoconfigure
Context
[Tree] (clear>router autoconfigure)
Full Context
clear router autoconfigure
Description
Commands in this context clear IP autoconfiguration information.
Platforms
7450 ESS-7, 7750 SR-1, 7750 SR-7, 7750 SR-1e, 7750 SR-2e, 7750 SR-s
autoconfigure
Syntax
autoconfigure
Context
[Tree] (show router autoconfigure)
Full Context
show router autoconfigure
Description
Commands in this context display IP autoconfiguration information.
Platforms
7450 ESS-7, 7750 SR-1, 7750 SR-7, 7750 SR-1e, 7750 SR-2e, 7750 SR-s